Amsec Biometric Instuctions

Amsec Biometric Instuctions
Biometric Safe Lock
Operating and Installation
Instructions
Part #4305278
Revised 02/10
Biometric Entry Pad
1.Fingerprint Reader Window
2.LCD Screen
3.Digital Pad
4.“Reset” Button
Electronic Actuator
American Security Products Co
Part #4305278
AMSEC Biometric Safe Lock Operating Instructions
ATTENTION:
• For indoor use only.
• Use one 9V alkaline battery. Manufacturer recommends to use Duracell™ or
Energizer® Alkaline batteries. Always use an alkaline battery for high quality
performance, otherwise controller might not work well.
• Battery Low Voltage: 5.4 ± 0.2V. The display will alert low battery when battery voltage
reaches 5.4±0.2V. PLEASE REPLACE THE BATTERY IMMEDIATELY.
Note: The voltage is checked during each time the entry pad is verifying fingerprints. In
the case of low battery, when the LCD screen light is off, i.e. the entry pad is not working;
the battery voltage will be a little higher than 5.4±0.2V. In this case, the battery does not
have enough power for operations other than fingerprint verification to unlock.
• When the display alerts low battery, the Biometric Entry Pad can only be operated to lock
or unlock. Operations, such as enrolling, deleting or time-delay setting, are not permitted.
Security level classification
Level 1: Entry pad can be operated by a code. (Factory Default)
Level 2: Entry pad must be operated by a fingerprint and its bound code. It is a higher
security level. Factory default security level is Level 2.
Level 3: Entry pad must be operated by a fingerprint or a code.
Note: Security Level 3 is a “Non-U.L. Certificated Operating Mode”.
For safety and security, all codes will be automatically deleted when security level is
changed. ID No. 01 code will be default code 1234567890.
Battery Replacement Instructions
In the back of Entry Pad you will see one 9 V alkaline battery. Take the battery out of the
battery compartment. Gently pull on the battery until it drops out.
Gently remove the connector by unsnapping it from the two terminals on the top of the
battery.
Never Pull on the Battery Leads.
Connect a new 9 V alkaline battery to the battery clip.
Put the battery and the leads completely back into the battery compartment.
For mounting and wiring information refer to the installation instructions in this manual.
02/10 American Security Products Co
Part #4305278
AMSEC Biometric Safe Lock Operating Instructions
Contents
1. Enroll the first fingerprint and its bound code for quick start (level 2). . . . . . . . . . . . . . . . . 5
2. Enroll the second fingerprint and its bound code (level 2). . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
3. Enroll additional fingerprint and its bound code (Level 2). . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4. Set time delay (Level 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
5. Unlock by an enrolled fingerprint and its bound code (Level 2). . . . . . . . . . . . . . . . . . . . . . . 7
6. Set/Change code (Level 2). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
7. Disable User (Level 2). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
8. Enable User (Level 2). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
9. Wrong try penalty (Level 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
10. Delete one user (Level 2). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
11. Delete all users (Level 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
12. Set Security Level. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
13. Set/Change the first code for quick start (Level 1) (Factory Default). . . . . . . . . . . . . . . . . 13
14. Enroll the second and additional codes (Level 1). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
15.
Enroll the first fingerprint for quick start (Level 3). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
16. Enroll the second and additional fingerprints (Level 3). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
17.
Set/Change code (Level 1 & Level 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
18. Set time delay (Level 1 & Level 3). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
19. Unlock by an enrolled user (Level 1 & Level 3). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
20. Disable /Enable user (Level 1). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
21.
Delete one user (Level 1 & Level 3). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
22. Delete all users (Level 1 & Level 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
23. Set number of doors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
24. Authorize Unlocking Doors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
25. System INFO.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
02/10
American Security Products Co
Part #4305278
AMSEC Biometric Safe Lock Operating Instructions
1. Enroll the first fingerprint and its bound code for quick start (Level 2)
Install Battery: In the back of entry pad, you will find a battery case. Install a brand new
9V alkaline battery.
12/11:34
8.6V
12/11:34
Capacity: 30 Users
Used: 00 User(s)
9.20071105-23
8.6V
Enroll
New User
12/11:34
8.6V
Place
Finger
Place your finger on the fingerprint reader window and hold.
12/11:34
8.6V
12/11:34
Enrolling

8.6V
Checking

12/11:34
8.6V
ID: 01
Enrolled
Note: Hold your finger on the reader window until the above displays finish one by one.
The first fingerprint with an ID No. 01 is enrolled.
12/11:34
8.6V
New Code
__
Enter a code (10 digits).
12/11:34
8.6V
Repeat
Enter the same code again.
__
12/11:34
8.6V
ID: 01
Code Saved
The first fingerprint and its bound code with ID No. 01 are enrolled successfully.
Note: The default password (1234567890) will be deleted automatically after the first
fingerprint and code are enrolled successfully.
2. Enroll the second fingerprint and its bound code (Level 2)
Place the first enrolled finger on the reader window and hold.
12/11:34
8.6V
Verifying

12/11:34
8.6V
ID: 01
Verified
12/11:34
8.6V
Enter Code
__
Enter the code (ID No. 01).
02/10 American Security Products Co
Part #4305278
AMSEC Biometric Safe Lock Operating Instructions
12/11:34
12/11:34
8.6V
8.6V
Lock Open
06 sec
User Code
Verified
Now the actuator is unlocked.
12/11:34
8.6V
Select
Menu
Press “Menu/OK”.
Press “” or “” to select “Enroll New User”.
12/11:34
8.6V
Enroll
New User
Press “Menu/OK” again.
Place your finger (different from the first one) on the fingerprint reader window and
hold.
12/11:34
8.6V
Enrolling

12/11:34
8.6V
Checking

12/11:34
8.6V
ID: 02
Enrolled
The second fingerprint, with an ID No. 02, is enrolled
12/11:34
8.6V
New Code
Enter a code (10 digits).
__
12/11:34
8.6V
Repeat
Enter the same code again.
__
12/11:34
8.6V
ID: 01
Code Saved
The second fingerprint and its bound code with ID No. 02 are enrolled successfully.
Note: The first two enrolled fingerprints and codes with ID No. 01 and 02 are administrators’
fingerprints and codes.
02/10
American Security Products Co
Part #4305278
AMSEC Biometric Safe Lock Operating Instructions
3. Enroll additional fingerprint and its bound code (Level 2)
Place an enrolled administrator’s finger (ID No. 01 or 02) on the reader window and hold.
After the fingerprint and its bound code are verified successfully, the LCD screen shows
“Select Menu”. Follow the same steps as to enroll the second administrator’s fingerprint
and code to complete the enrollment.
4. Set time delay (Level 2)
Place an enrolled administrator’s finger (ID No. 01 or 02) on the reader window and hold.
After the fingerprint and its bound code are verified successfully, then the LCD screen
shows “Select Menu”, press “Menu/OK”. Press “” or “” to select “Set/Cancel Time Delay”.
12/11:34
8.6V
Set/Cancel
Time Delay
12/11:34
Press “Menu/OK”.
8.6V
Time Delay
00 min
Press “” or “” to set time delay (1 to 99 min). Press “Menu/OK”
12/11:34
8.6V
Time Window
01 min
Press “” or “” to set Time Window (0 to 15 min). Press “Menu/OK”.
ATTENTION:
During Time Delay period, user can operate the entry pad, such as enrolling deleting etc.,
but the actuator will not be unlocked.
After the original time delay is changed successfully, the time delay for the first time
unlocking is the same as the original one. The new time delay will be effective afterwards.
When changing time delay, if the period is longer than the previous one, the new time
delay will be effective in the next unlocking. If the period is shorter than the previous one,
the new time delay will be effective after the next unlocking.
5. Unlock by an enrolled fingerprint and its bound code (Level 2)
Place an enrolled fingerprint on the fingerprint reader window and hold until the LCD
shows “ID No. Verified”. Enter its bound code. After the bound code is verified, the entry
pad will be unlocked after Time Delay ends.
02/10 American Security Products Co
Part #4305278
AMSEC Biometric Safe Lock Operating Instructions
For example:
Time Delay is set 20 minutes and Time Window 10 minutes. Place an enrolled finger
(e.g. ID 03) on the fingerprint reader window and hold. After successful fingerprint’s
verification, enter its bound code. Then, the LCD will show:
12/11:34
8.6V
Time Delay
Start
The entry pad will start counting up. The LCD screen flashes every 15 seconds for the
past time. When time delay finishes counting, two beeps will sound and the LCD screen
will show:
12/11:34
8.6V
TM Window
10:00
The entry pad will start counting down again. The LCD screen flashes every 15 seconds
for remaining time.
During the 10 minute time window, user can verify an enrolled fingerprint and enter
code again to unlock the entry pad with the LCD showing:
12/11:34
8.6V
Lock Open
06 sec
The entry pad is unlocked.
Note: When the entry pad starts its Time Delay process, user can operate the entry pad, but
the actuator will not be unlocked even if the verification is successful.
If no enrolled fingerprint or code is successfully verified during Time Window period, the
actuator will be locked to the end and the LCD will show:
12/11:34
8.6V
TM Window
End
Note: If the Time Window is set 0 minutes, there is no need to verify second time. When
Time Delay ends, the actuator will be unlocked automatically.
02/10
American Security Products Co
Part #4305278
AMSEC Biometric Safe Lock Operating Instructions
6. Set/Change code (Level 2)
Unlock with the enrolled fingerprint and its bound code that you want to set/change
code (e.g. ID No. 03). The LCD will show “ID: 03 Verified” and “Lock Open 06 sec”, followed
by “Select Menu” and:
12/11:34
8.6V
Set/Change
Code
12/11:34
Press “Menu/OK”.
8.6V
New Code
__
Enter a code (10 digits).
12/11:34
8.6V
Repeat
Enter the same code again.
__
12/11:34
8.6V
ID: 03
Code Saved
Now the user code with an ID No. 03 is enrolled successfully.
7. Disable user (Level 2)
Unlock with an administrator’s fingerprint and code (ID No. 01 or 02). When the LCD
shows “Select Menu”, press “Menu/OK”. Press“ ” or “” to select Disable User.
12/11:34
8.6V
Disable
User
Press “Menu/OK”.
Press “” or “” to select the ID No. to disable (e.g. ID 03).
12/11:34
8.6V
ID: 03 User
Disable?
12/11:34
Press “Menu/OK”.
8.6V
ID: 03 User
Disable?
Now the user (ID No. 03) is disabled.
02/10 American Security Products Co
Part #4305278
AMSEC Biometric Safe Lock Operating Instructions
Note: Administrators cannot be disabled.
8. Enable User (Level 2)
Unlock by an administrator. When the LCD shows “Select Menu”, press “” or “” to
select “Enable User”.
12/11:34
8.6V
Enable
User
Press “Menu/OK”.
Press “” or “” to select the ID No. to enable (e.g. ID 03).
12/11:34
8.6V
ID: 03 User
Enable?
12/11:34
Press “Menu/OK”.
8.6V
ID: 03 Code
Enabled
Now the user (ID No. 03) is enabled. Repeat these steps for each user, (ID No. 4 and so on.
9. Wrong entry penalty
Four (4) consecutive invalid code entries initiate a 4-minute delay period with the LCD
showing:
12/11:34
8.6V
Device
Locked
The entry pad is shut down and no operation is permitted.
Then, the entry pad will start counting down with the LCD flashing the remaining time
every 15 seconds. e.g.
12/11:34
8.6V
Locked
03:45
After the count down is finished, the entry pad is ready to use again.
10 02/10
American Security Products Co
Part #4305278
AMSEC Biometric Safe Lock Operating Instructions
Note: Two more consecutive invalid codes will restart an additional 4 minute delay
period. An attempt to unlock by an enrolled fingerprint will not terminate the delay
period.
10. Delete One User (Level 2)
Unlock by an administrator. When the LCD shows “Select Menu”, press “” or “” to
select “Delete One User”.
12/11:34
8.6V
Delete
One User
Press “Menu/OK”.
Press “” or “” to select the ID No. to delete (e.g. ID 03).
12/11:34
8.6V
Delete
ID: 03?
12/11:34
Press “Menu/OK”.
8.6V
User ID: 03
Deleted
Now the user with ID No. 03 user is deleted.
11. Delete All Users (Level 2)
Unlock by an administrator. When the LCD shows “Select Menu”, press “” or “” to
select “Delete All Users”.
12/11:34
8.6V
Delete
All Users
12/11:34
Press “Menu/OK”.
8.6V
Delete All
OK?
Press “Menu/OK” again.
The entry pad starts deleting users from ID No. 01 to ID No. 30. When the LCD screen
shows “All Users Deleted”, all users are deleted successfully.
02/10 11
American Security Products Co
Part #4305278
AMSEC Biometric Safe Lock Operating Instructions
12. Set Security Level
Unlock the entry pad by an administrator. When the LCD shows “Select Menu”, press “”
or “” to select the security level you want.
For example, if you set the level to Level 2, find and select Security Level 2.
12/11:34
8.6V
Security
Level 2
12/11:34
Press “Menu/OK”.
8.6V
12/11:34
Open Lock by
Fingerprint and Code
8.6V
12/11:34
Set to Security Level 2.
All Users will be deleted
8.6V
Delete
All Users?
Press “Menu/OK” again.
12/11:34
8.6V
Deleting
ID: 01
12/11:34
8.6V
All Users
Deleted
12/11:34

8.6V
Deleting
ID: 30
12/11:34
8.6V
Security
Level 2 Set
Follow the same steps to set to Level 3.
12/11:34
8.6V
Security
Level 1
12/11:34
Press “Menu/OK”.
8.6V
Security
Level 1 Set
If you want to set Level 3, find and select Security Level 3 and press “Menu/OK”.
“Open Lock by Fingerprint or Code”, “Set to Security Level 3, All Users will be deleted” and
“Delete All Users?” will be displayed on the LCD screen. Press “Menu/OK” again. All users
will be deleted and the security level is set to Level 3.
Note: Security Level 3 is a “Non-U.L. Certificated Operating Mode”.
12 02/10
American Security Products Co
Part #4305278
AMSEC Biometric Safe Lock Operating Instructions
Note: For safety and security, all codes will be automatically deleted when security level
is changed. ID No. 01 code will be default code 1234567890.
13. Set/Change the first code for quick start (Level 1) (Factory Default)
When setting Security Level is changed Level 2 to Level 1, the default code is
1234567890. Press “Code”.
12/11:34
8.6V
Enter Code
__
Enter the default code, 123456790.
When the LCD screen shows “Select Menu”, press “” or “” to select “Set/Change Code”.
12/11:34
8.6V
Set/Change
Code
12/11:34
Press “Menu/OK”.
8.6V
Repeat
Enter a code (10 digits).
__
12/11:34
8.6V
ID: 01
Code Saved
Enter the same code again.
The first code with an ID No. 01 is changed successfully.
Note: All enrolled codes with corresponding ID No. will keep effective when security
level is changed from Level 2 to Level 1. The default code will be automatically replaced
by the code with ID No. 01.
14. Enroll the second and additional codes (Level 1)
Press “ Code”. Enter an administrator’s code (ID No. 01 or 02). When the LCD screen
shows “Select Menu”, press “Menu/OK”. Press “” or “” to select “Enroll New User”.
12/11:34
8.6V
Enroll
New User
02/10 Press “Menu/OK”.
13
American Security Products Co
Part #4305278
AMSEC Biometric Safe Lock Operating Instructions
12/11:34
8.6V
New Code
Enter a code (10 digits).
__
12/11:34
8.6V
Repeat
Enter the same code again.
__
12/11:34
8.6V
ID: 02
Code Saved
The second code with an ID No. 02 is enrolled successfully.
Note: The first two enrolled codes with ID No. 01 and 02 are administrators’ codes.
15. Enroll the first fingerprint for quick start (level 3)
When setting Security Level is changed to Level 3, place a finger on the fingerprint
reader window.
12/11:34
8.6V
Place
Finger
Place your finger on the fingerprint reader window and hold.
12/11:34
8.6V
Enrolling

12/11:34
8.6V
Checking

12/11:34
8.6V
ID: 01
Enrolled
The first fingerprint with an ID No. 01 is enrolled successfully
Note: The default password, 1234567890 will be deleted automatically after the first
fingerprint is enrolled successfully.
16. Enroll the second or additional fingerprints (level 3)
Place the first enrolled finger (ID No. 01) on the reader window and hold. When the LCD
screen shows “Select Menu”, press “” or “” to select Enroll New User.
14 02/10
American Security Products Co
Part #4305278
AMSEC Biometric Safe Lock Operating Instructions
12/11:34
8.6V
Enroll
New User
12/11:34
Press “Menu/OK” again.
8.6V
Place
Finger
Place your finger (different from the first one) on the fingerprint reader window and hold.
12/11:34
8.6V
Enrolling

12/11:34
8.6V
Checking

12/11:34
8.6V
ID: 02
Enrolled
The second fingerprint, with an ID No. 02, is enrolled successfully.
Note: The first two enrolled fingerprints with ID No. 01 and 02 are administrators’
fingerprints.
Unlock by an administrator. Follow the same steps to enroll additional fingerprints.
17. Set/Change code (Level 1 & Level 3)
Unlock with the code (Level 1) or fingerprint (Level 3) which you want to set/Change
code. After successful verification, follow the same steps in 13. Set/Change the first code
for quick start (Level 1).
Note: User code can be set or changed only after being enabled. (Level 3)
Unlock by an administrator. When the LCD screen shows “Select Menu”, press “”
or “” to select “Enable User Code” and press “Menu/OK”.
Press “” or “” to select the ID No. of user (For example: ID No. 03 user code) to
be enabled and press “Menu/OK”.
When the LCD screen shows “ID No.: 03 Code Enabled”, the No. 03 user code is
enabled successfully.
18. Set time delay (Level 1 & Level 3)
Unlock by an administrator. After successfully verification, follow the same steps in 4 (Set
time delay in Level 2).
19. Unlock by an enrolled user (Level 1 & Level 3)
Press “ Code” and enter an enrolled code. Or place an enrolled fingerprint on the
02/10 15
American Security Products Co
Part #4305278
AMSEC Biometric Safe Lock Operating Instructions
fingerprint reader window. The LCD shows “ID No. Verified” followed by Time Delay.
For example:
Time Delay is set 20 minutes and Time Window 10 minutes. After an enrolled code is
verified successfully, the LCD shows:
12/11:34
8.6V
Time Delay
20:00
The entry pad will start counting down. The LCD screen flashes every 15 seconds for
remaining time. When Time Delay finishes counting down, two beeps will sound and the
LCD screen will show:
12/11:34
8.6V
TM Window
10:00
The entry pad will start counting down again. The LCD screen flashes every 15 seconds
for remaining time .
During the 10 minute Time Window, user can verify an enrolled code or fingerprint again
to unlock the entry pad with the LCD showing:
12/11:34
8.6V
Lock Open
06 sec
Note: When the entry pad starts its Time Delay process, user can operate the entry
pad normally, but the actuator will not be unlocked even if the verification is
successful.
If no enrolled code or fingerprint is verified successfully during Time Window
period, the actuator will be locked to the end and the LCD will show:
12/11:34
8.6V
TM Window
End
Note: If the Time Window is set 0 minute, there is no need to verify second time. When
Time Delay ends, the actuator will be unlocked automatically
16 If Time Delay is set 0 minute, Time Window will automatically be 0 minute After
successful verification, the actuator will be unlocked automatically.
02/10
American Security Products Co
Part #4305278
AMSEC Biometric Safe Lock Operating Instructions
20. Disable /Enable user (Level 1 & Level 3)
Unlock by an administrator. After successful verification, follow the same steps in 7
(Disable user in Level 2) or 8 (Enable user in Level 2).
Note: Administrators can not be disabled.
21. Delete One User (Level 1 & Level 3)
Unlock by an administrator. After successfully verification, follow the same steps in 11
(Delete one user in Level 2).
22. Delete All Users (Level 1 & Level 3)
Unlock by an administrator. After successfully verification, follow the same steps in 12
(Delete All Users in Level 2).
Note: When all users are deleted successfully in Level 1, the default code, 1234567980,
will be effective as ID No. 01.
23. Set number of doors
Unlock by an administrator (ID No. 01 or 02) . When the LCD screen shows “Select Menu”.
Press “” or “” to select “Set number of doors”.
12/11:34
8.6V
Set Number
of Doors
12/11:34
Press “Menu/OK”.
8.6V
Number of
Doors: 01
Press “” or “” to set number of doors. For example, to set the number of doors to 2,
select 02 and press “Menu/OK”. Now the number of doors is set to 2 successfully.
Note: The default number of doors is 01.
If setting the number of doors to be 02, 03 or 04, after the entry pad verifies user
successfully, push “12” to unlock Door 1, or push “345” to unlock Door 2, or push
“678” to unlock Door 3, or push “90” to unlock Door 4.
If setting the number of doors to be 01, after the entry pad verifies user
successfully, the door will open directly.
Note: If Security Level is changed or system is recovered, the number of doors will
remain.
02/10 17
American Security Products Co
Part #4305278
AMSEC Biometric Safe Lock Operating Instructions
24. Authorize Unlocking Doors
Unlock by an administrator. When the LCD screen shows “Select Menu”, press “” or “”
to select “Authorize Doors”.
12/11:34
8.6V
Authorize
Doors
12/11:34
Press “Menu/OK”.
8.6V
User ID
From: 03
Press “” or “” to set the first ID in the group, the users will be authorized. Press “Menu/
OK”.
12/11:34
8.6V
User ID
From: 05
Press “” or “” to set the last ID in the group the users will be authorized. For example,
to authorize users with ID No. from 03 to 05, press “Menu/OK”.
12/11:34
Doors
Auth.
8.6V
1234
oxxx
“Door 1234” means maximum number of doors. “Auth. oxxx” means whether each door
is authorized to open by the group or not. Letter “o” means the group is authorized to
open the door. Letter “x” means the group is not authorized.
When one letter flashes, press “” or “” to set “o” or “x”.
Press “Menu/OK” to confirm. Press “Back”, the left letter will flash again and it can be set
again.
Note: Administrators (ID No. 01 and 02) can open all doors.
For example, to authorize users with ID No. 03, 04 and 05 to be able to open Door
2: when the LCD screen shows:
12/11:34
Doors
Auth.
8.6V
1234
oxxx
The first letter “x” is flashing. Press “” or “” to set it to be “x”. Press “Menu/OK”.
18 02/10
American Security Products Co
Part #4305278
AMSEC Biometric Safe Lock Operating Instructions
The second letter will flash. Press “” or “” to set “o”. Press “Menu/OK”.
Press “Menu/OK” twice to confirm the condition of Door 3 and 4.
12/11:34
Doors
Auth.
8.6V
1234
xoxx
Now the authorization is successful. Users with ID No. 03, 04 and 05 can open Door 2.
25. System INFO.
Press “Menu/OK”. The screen will show “Select Menu”. Press “” or “” to select “System
INFO.”.
Press “Menu/OK” and the LCD will show:
12/11:34
8.6V
Capacity: 30 Users
Used: 00 User(s)
9.20071105-23
It means that up to 30 users can be enrolled into the entry pad and there is no user
enrolled now. The entry pad version is 9.20071105-23.
02/10 19
PURCHASE RECORD
Model #:________________________________________________
Serial #:_ _______________________________________________
Date of Purchase:________________________________________
Purchased From:_________________________________________
Company:_______________________________________________
Address:________________________________________________
City____________________ State_______ Zip Code____________
Telephone #:_ ___________________________________________
Email Address:_ _________________________________________
Website:________________________________________________
If you would like us to send AMSEC Safe information to a friend or
have any questions concerning our complete line of security products,
please send your request to:
AMERICAN SECURITY
PRODUCTS COMPANY
11925 Pacific Ave
Fontana, CA 92337
Visit us on the web at:
www.amsecusa.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement