2014 Catalogue (Download PDF)

2014 Catalogue (Download PDF)
TABLE OF CONTENTS
Company Profile. . . . . . . . . . . . . . . . . . . 4-5
MR16 LED Emergency Lighting . . . . . . . 6-7
Nexus® Management System. . . . . . . . . 8-9
EXIT SIGNS
Table of contents. . . . . . . . . . . . . . . . . . . 13
Introduction. . . . . . . . . . . . . . . . . . . . . 14-15
EDE Series . . . . . . . . . . . . . . . . . . . . . 16-17
EX30 Series. . . . . . . . . . . . . . . . . . . . . 18-19
EAE Series. . . . . . . . . . . . . . . . . . . . . . . . 20
EX3 Series. . . . . . . . . . . . . . . . . . . . . . . . 21
C8SR3 Series . . . . . . . . . . . . . . . . . . . . . . 22
EX3F Series. . . . . . . . . . . . . . . . . . . . . . . 23
C8SR35 Series . . . . . . . . . . . . . . . . . . . . 24
C8ES35 & C8SE35 Series. . . . . . . . . . . . 25
C8E/S35R Series. . . . . . . . . . . . . . . . . . . 26
PRE Series . . . . . . . . . . . . . . . . . . . . . . . 27
Prestige™ LPEX100 Series . . . . . . . . . . . 28
Prestige™ LPSR100 Series . . . . . . . . . . . 29
LPEX300 Series. . . . . . . . . . . . . . . . . . . . 30
LPSR300 Series . . . . . . . . . . . . . . . . . . . 31
C8ES300 & C8SE300 Series . . . . . . . . . . 32
EA Series. . . . . . . . . . . . . . . . . . . . . . . . . 33
LPEX50 Series. . . . . . . . . . . . . . . . . . . . . 34
C8SR50 Series . . . . . . . . . . . . . . . . . . . . 35
LPEX Series. . . . . . . . . . . . . . . . . . . . . . . 36
LPEX54 Series. . . . . . . . . . . . . . . . . . . . . 37
C8ES70 & C8SE70 Series. . . . . . . . . . . . 38
ES70B12 & SE70B12 Series. . . . . . . . . . 39
EAC Series . . . . . . . . . . . . . . . . . . . . . 40-41
LPEX50-P Series. . . . . . . . . . . . . . . . . . . 42
C8SR50-P Series. . . . . . . . . . . . . . . . . . . 43
ES Series. . . . . . . . . . . . . . . . . . . . . . . . . 44
EX10 Series. . . . . . . . . . . . . . . . . . . . . . . 45
C8SR10 Series . . . . . . . . . . . . . . . . . . . . 46
C8ES10 & C8SE10 Series. . . . . . . . . . . . 47
ESC Series . . . . . . . . . . . . . . . . . . . . . . . 48
EX10-P & LPEX10-P Series . . . . . . . . . . 49
SR Series. . . . . . . . . . . . . . . . . . . . . . . 50-51
12ESL-EX Series. . . . . . . . . . . . . . . . . . . 52
12ESL-SR Series. . . . . . . . . . . . . . . . . . . 53
EP Series. . . . . . . . . . . . . . . . . . . . . . . . . 54
Premier™ Exit Series. . . . . . . . . . . . . . . . 55
Premier™ Combo Series. . . . . . . . . . . 56-57
C8SRPK Series. . . . . . . . . . . . . . . . . . . . 58
C8ESPK & C8SEPK Series . . . . . . . . . . . 59
C8SRPK-P Series . . . . . . . . . . . . . . . . 60-61
Survive-All™ EN Series . . . . . . . . . . . . . . 62
Survive-All™ LPEX600 Series . . . . . . . . . 63
Survive-All™ ENC Series. . . . . . . . . . . . . 64
Survive-All™ LPEX600-N Series . . . . . . . 65
EH Series . . . . . . . . . . . . . . . . . . . . . . . . 66
LPEXHZ Series . . . . . . . . . . . . . . . . . . . . 67
EHC Series . . . . . . . . . . . . . . . . . . . . . 68-69
EXHZ Series . . . . . . . . . . . . . . . . . . . . 70-71
EX Series. . . . . . . . . . . . . . . . . . . . . . . 72-73
LPEX-XP Series. . . . . . . . . . . . . . . . . . 74-75
C8SRXP Series . . . . . . . . . . . . . . . . . . 76-77
EXP Exit Series. . . . . . . . . . . . . . . . . . 78-79
EXP Sortie Series . . . . . . . . . . . . . . . . 80-81
ET Series. . . . . . . . . . . . . . . . . . . . . . . . . 82
Special Wording . . . . . . . . . . . . . . . . . . . 83
LED Retrofit Kits. . . . . . . . . . . . . . . . . 84-86
Pendant Kit. . . . . . . . . . . . . . . . . . . . . . . 87
Wire Guards . . . . . . . . . . . . . . . . . . . . 88-89
EZ2™ Canopy . . . . . . . . . . . . . . . . . . . . . . 90
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . 91
BATTERY UNITS
Table of contents. . . . . . . . . . . . . . . . . . . 95
Introduction. . . . . . . . . . . . . . . . . . . . . 96-97
Lux-Ray™ Series . . . . . . . . . . . . . . . . . 98-99
Retract-a-Lite™ Series . . . . . . . . . . . . . 100
Mini Retract-a-Lite™ Series . . . . . . . . . 101
Provider™ Series . . . . . . . . . . . . . . . . . . 102
Distinction™ Recessed Series. . . . . . . . . 103
Distinction™ Series . . . . . . . . . . . . . 104-105
DEL Series . . . . . . . . . . . . . . . . . . . 106-107
ESLT Series. . . . . . . . . . . . . . . . . . . 108-109
Wonderpack™ WP36 Series. . . . . . . . . . 110
Eclipse™ Series. . . . . . . . . . . . . . . . . . . 111
JMLC Series . . . . . . . . . . . . . . . . . . 112-113
JMLA Series . . . . . . . . . . . . . . . . . . . . . 114
JEM18P Series . . . . . . . . . . . . . . . . . . . 115
Premier™ Series . . . . . . . . . . . . . . . 116-117
ESL Series. . . . . . . . . . . . . . . . . . . . 118-119
Survive-All™ NXM Series. . . . . . . . . 120-121
IPE Series. . . . . . . . . . . . . . . . . . . . . . . 122
SIPE Series. . . . . . . . . . . . . . . . . . . . . . 123
ESLPK Series . . . . . . . . . . . . . . . . . 124-125
HZM Series. . . . . . . . . . . . . . . . . . . 126-127
ESLNX Series . . . . . . . . . . . . . . . . . 128-129
48 & FPS Series . . . . . . . . . . . . . . . . . . 130
Glossary . . . . . . . . . . . . . . . . . . . . . . . . 131
REMOTE FIXTURES
Table of contents. . . . . . . . . . . . . . . . . . 135
Introduction. . . . . . . . . . . . . . . . . . . 136-137
Lux-Ray™ Series . . . . . . . . . . . . . . . . . . 138
EF40 & EF40-P Series . . . . . . . . . . . . . 139
Retract-a-Lite™ Series . . . . . . . . . . . . . 140
3
Mini Retract-a-Lite™ Series . . . . . . . . . 141
Literay™ Series . . . . . . . . . . . . . . . . . . . 142
EF9/EF9Q/EF9M Series. . . . . . . . . . . . . 143
EF15 Series. . . . . . . . . . . . . . . . . . . . . . 144
EF18/EF18D/EF18T Series. . . . . . . . . . 145
Distinction™ Series . . . . . . . . . . . . . . . . 146
Distinction™ EFR Series . . . . . . . . . . . . 147
Survive-All™ EF39&EF39-P Series. 148-149
EF25 Series. . . . . . . . . . . . . . . . . . . . . . 150
EF26/EF26DS/EF26D Series. . . . . . . . . 151
EF11 Series. . . . . . . . . . . . . . . . . . . . . . 152
EF30 Series. . . . . . . . . . . . . . . . . . . . . . 153
EF41 Series. . . . . . . . . . . . . . . . . . . . . . 154
EFXPR. . . . . . . . . . . . . . . . . . . . . . . . . . 155
Lamp Charts. . . . . . . . . . . . . . . . . . 156-158
Glossary . . . . . . . . . . . . . . . . . . . . . . . . 159
CENTRAL SYSTEMS
Table of contents. . . . . . . . . . . . . . . . . . 163
What is Emex . . . . . . . . . . . . . . . . . 164-165
IPS Single Phase Series. . . . . . . . . 166-167
IPS Three Phase Series . . . . . . . . . 168-169
System Options. . . . . . . . . . . . . . . . . . . 170
User Interface & Display Functions. . . 171
Central System Request Data Form. . . 172
Unity Series. . . . . . . . . . . . . . . . . . . 174-175
CH Series . . . . . . . . . . . . . . . . . . . . 176-178
OPTION & ACCESSORIES
Table of contents. . . . . . . . . . . . . . . . . . 183
LED Retrofit Kits. . . . . . . . . . . . . . . 184-185
LED BULB Series . . . . . . . . . . . . . . . . . 186
48 & FPS Series . . . . . . . . . . . . . . . . . . 187
EZ2™ Canopy . . . . . . . . . . . . . . . . . . . . . 188
Pendant Kit. . . . . . . . . . . . . . . . . . . . . . 189
Wire Guards . . . . . . . . . . . . . . . . . . 190-191
Nexus® Management System. . . . . 192-193
TECHNICAL INFORMATION
Table of contents. . . . . . . . . . . . . . . . . . 197
Wire Size Guide. . . . . . . . . . . . . . . . . . . 198
Battery Unit Capacity Chart . . . . . . . . . 199
Electrical Code . . . . . . . . . . . . . . . . 200-201
Building Code . . . . . . . . . . . . . . . . . 202-205
Fire & Genrator Room Code. . . . . . . . . 206
Limited Warranty . . . . . . . . . . . . . . . . . 207
Product Index . . . . . . . . . . . . . . . . . . . . 208
COMPANY PROFILE
UNIQUE NORTH AMERICAN
THOMAS & BETTS MANUFACTURING
FACILITY
Vertically-integrated manufacturing and production
capabilities in North America give Thomas & Betts complete
control over lead time, service, and quality down to the
smallest detail. We produce exactly what we need when
we need it, without waiting for large production runs or
overseas shipping. With everything under one roof, we can
ensure that our stringent quality standards are met at every
step in the process from design to production to order
fulfillment.
INNOVATIVE
The in-house research and development team of highly
skilled professional electrical and mechanical engineers,
designers, and technicians at Thomas & Betts includes
specialists with over twenty-five years of experience in
the emergency lighting industry. This multi-disciplinary
group uses advanced technology in all specialties from
mechanical design to operating system software, RF and
power electronic design, lighting design, and LED drivers to
continuously create innovative emergency lighting solutions.
Comprehensive engineering services are provided to meet
special requests from customers for unique applications.
Quality and safety are designed into each product at
conception, and customized testing equipment is created to
ensure that each unit meets codes and conforms to internal
quality control standards including ease of installation and
reliability over time.
Fuelled by the creativity, innovation and commitment of every
employee, the Thomas & Betts facility is a centre of excellence
in emergency lighting.
RELIABLE
Technologically advanced printed circuit board production
lines at the Thomas & Betts manufacturing facility produce
thousands of circuit boards daily. Skilled production
personnel are trained according to IPC standards, and
use board traceability and tracking software to ensure
quality. Universal SMT (surface mount technology) boards
and TH (through-hole) insertion boards are produced in
house on multiple lines. Every station is ESD (electro-static
discharge) protected to eliminate static hazards, and our
ROHS-compliant wave soldering machine meets lead-free
criteria. Automatic insertion equipment and automatic
silicone coating application ensure high productivity and
quality. Highly efficient electro-mechanical assembly lines
are optimized for low volume, high mix production runs
with thousands of final assemblies produced each day.
Customizations such as specific punching, exact wording,
and color matching can be completed quickly using our
in-house machine shop and painting capabilities.
All orders undergo functional testing and quality inspection,
with high-voltage, high-amperage power outage simulations
available to test all central power systems for each
customer’s specific requirements. Specialized facilities
include a dark room for color contrast measurement;
temperature and humidity controlled environments; wall,
ceiling and suspended ceiling installation simulations; and
cycle testing automation.
4
EFFICIENT
Large inventories are ready to ship from warehouses
across the country for fast delivery. To reduce the carbon
footprint and minimize the environmental impact of
operations, a Sustainable Development policy is in effect
at the Thomas & Betts manufacturing facilities. Through
a series of initiatives, reductions in usage of water, water
bottles, electricity and natural gas, packaging, and pallets
have already been realized. Forward-looking initiatives
include reductions in paper, further recycling of pallets, and
implementation of an eco-delivery schedule.
Frequent investments in new equipment improve lead time and
enforce the high quality and reliability standards of Thomas
& Betts. The new AOI (automated optical inspection) machine
added to the printed circuit board operation in 2012 is one of
the first of its kind in use in North America.
The Thomas & Betts manufacturing facility has been ISO 9001
compliant since 2001.
5
MR16 LED EMERGENCY LIGHTING
MR16 LED ILLUMINATION
MR16 LED LAMP BENEFITS
With the remarkable technology development in the last
decade, the light-emitting diode (LED) is becoming the
preferred solution in low- and medium-power lighting
applications. The emergency lighting industry is no
exception: today virtually every new product introduced to
market includes “white” LEDs for emergency illumination.
• CSA C22.2 No. 141 certified.
• Energy-efficient LED MR16 lamp provides equivalent
lighting performance to a much higher watt halogen
MR16 lamp.
• Reduces required battery capacity by 75%, providing
necessary illumination with fewer remote heads and
battery units for project cost savings.
Extremely efficient and long-lasting, LED lamps become the
natural alternative to incandescent lamps due to three main
advantages:
•S
mall profile, compact white lighting is ideal for
architectural applications.
• = lamp efficacy: 50 - 70 lumen per watt compared to 15 30 lumen per watt of the best halogen lamp.
•V
ibration-resistant LED stands up to industrial
environments.
• = operational life: 30,000+ hours, equivalent to a lifetime
warranty in emergency lighting.
• Ideal for indoor and outdoor use.
• = lower lamp temperature (80 - 120°C) is a huge benefit
for lighting in hazardous locations.
340-LUMEN 5W MR16 LED
Keeping pace with technology, in 2012 we introduced a
12V-5W MR16 LED lamp. With a typical luminous flux of 340
lumens, this lamp has the same lighting performance as
a 20W high-output halogen MR16. A twin emergency head
installed at a height of 7.5ft illuminates more than a 70ft
path of egress.
200-LUMEN 4W MR16 LED
Leading the technology trend, Emergi-Lite® offers a
complete series of 4W MR16 LED lamps available for all
the standard battery voltages: 6V, 12V, 24V and 120V. With
up to 30,000 hours of operational life and a luminous
flux of typically 200 lumens, they are available with most
emergency heads designed to hold an MR16 lamp and meet
the majority of illumination specifications. For example: one
pair of LED emergency heads installed at a height of 7.5ft,
illuminates a 6ft by 40ft path of egress.
Compared to halogen lamps (16-20W), these 4W MR16
LED lamps illuminate the same area of egress during an
emergency situation by using 75% less power. This has
a direct impact on the battery size, reducing the back-up
capacity needs by 75%. Consequently, it also reduces the
total cost of the application, with the use of smaller battery
capacity units, the possibility of using fewer fixtures due to
superior illumination, thus also reducing electrical wiring,
and it it reduces the environmental footprint.
40’
1FC
ave
rag
e
70’
1FC
ave
rag
e
7.5’
6’
510-LUMEN 6W MR16 LED
New in Fall 2013, we intoduce a 12V - 6W MR16 LED lamp,
which offer typical luminous flux of 510 lumens. Like the
lower wattage MR16 LED lamps, this new lamp is specially
designed for emergency lighting. It offers the same lighting
preformance as the 35W or 20W Mr16 IR. A twin emergency
head installed at a height of 7.5’ illuminates approximately
100’ path of egress.
7.5’
6’
100’
1FC
ave
rag
e
7.5’
6’
6
CASE STUDY: FEWER MR16
LED UNITS REQUIRED
•R
educed Maintenance and Testing Costs, with fewer units
to maintain and test in the Emergency Lighting System.
Emergency lighting units with MR16 LED lamps provide the
same illumination at floor level using significantly fewer
units.
•R
educed Lamp Replacement Costs. LED lamps have a
30,000+ hour lamp life compared to only a few hundred
hours typical with incandescent lamps.
•R
educed Installation Costs, due to reduced product and
labour requirements.
•R
educed Environmental Impact, less product materials,
less batteries, less transportation, less packaging, less
labor, less waste.
•R
educed Energy Costs, keeping fewer batteries charged
at full capacity to be ready to respond to an emergency
situation at any time.
COMPARE
Where the building code requires an average of 1 foot-candle and a minimum of 0.1 foot-candle at floor level along the path
of egress on a 150’ x 9’ x 9’ corridor with an egress door at one end, a 150’ x 6’ path of egress, and a 7.5’ unit mounting
height.
4W MR16 LED LAMPS
STANDARD WEDGE-BASE 9W
INCANDESCENT LAMP
Same Standard Emergency Lighting Units with
4W MR16 LED Lamps
Standard Emergency Lighting Units
with 9W wedge-base incandescent lamps
LAMP
SUFFIX
5W MR16 LED LAMPS
LAMP
SUFFIX
VOLTAGE
WATTAGE
LI
12
5
VOLTAGE
WATTAGE
LUMENS REPLACEMENT #
LA
6
4
130
580.0097-E
LG
12
4
170
580.0093-E
LL
24
4
200
580.0098-E
NEW! 6W MR16 LED LAMPS
LUMENS REPLACEMENT #
340
580.0104-E
7
LAMP
SUFFIX
VOLTAGE
WATTAGE
LJ
12
6
LUMENS REPLACEMENT #
510
580.0106-E
NEXUS® EMERGENCY LIGHTING
MANAGEMENT SYSTEM
MAXIMIZE SYSTEM AVAILABILITY
ARE YOU PREPARED FOR A SAFETY
INSPECTION?
By allowing maintenance personnel to easily maintain and
monitor the emergency lighting system without having
to manually check each unit, Nexus® reduces the hours
required to disrupt the power supply for inspections. With
Nexus®, monthly tests and reports on the status of all
emergency lights and exit signs can be done individually, in
groups, or together.
Building & Life Safety Codes oblige building owners/
managers to ensure the safe evacuation of a building
in the event of an emergency. In the interest of public
safety, building owners/managers must meet the outlined
requirements for exit signs and emergency lighting
equipment, including the following:
Advantages of the Nexus® system include saving labor;
maximizing system availability by testing units in groups
and stages rather than setting all units in recovery mode;
and the convenience of self-monitoring. Nexus® indicates
the location of a faulty unit and reports it instantly without
requiring a manual search.
• Conduct a discharge test every month.
• Conduct functional tests annually.
• Keep a log book of maintenance information.
Complying with these requirements can be labour intensive
and costly, especially in large buildings where testing every
emergency light requires many man-hours.
UPDATE STATUS INSTANTLY
Nexus® passes messages both to and from the emergency
units to instruct the units to perform all mandatory testing
by communicating between the emergency units and a
centrally located controller.
Disrupting the power supply during lengthy inspections can
also put public safety at risk.
MANAGE TESTING WITH NEXUS® TO SAVE
TIME AND COSTS
Nexus® is a proven system supported by a 5-year warranty,
and can contribute to LEED certification and support green
building initiatives.
Nexus® is a real-time monitoring system that manages
the status of your entire Emergency Lighting and Exit Sign
system from a central control unit. Nexus® runs diagnostics,
performs required monthly and annual functional tests,
generates maintenance logs and runs compliance reports.
Available in wired or wireless (RF) versions, Nexus®
installations often pay for themselves in less than two years.
In addition to operational savings, Nexus® helps increase
system reliability and performance and reduces the risk
of failed inspections. One building or a group of properties
under the same management can be monitored with Nexus®.
8
SMALL SYSTEM EXAMPLE
In a system of fewer than 100 units it is most likely that
the only hardware required, other than the emergency
units themselves, is a controller. All communication
would occur wirelessly and installation would not
vary greatly from a non-monitored system. Once the
units are in place, the system will establish the mesh
network. The building itself could be quite large as each
unit only needs to be able to communicate with its close
neighbours and does not need to communicate directly
with the controller.
LARGE SYSTEM EXAMPLE
The Nexus® RF system has been designed to be
extremely flexible and provides for a range of system
options. Each large site will need to be assessed
for the best system solution with the assistance of
Thomas & Betts technical staff.
The basic Nexus® RF system is designed to run on an
Ethernet network which is present in most modern
buildings; however, through a range of interface cards
the backbone of the network could be WLAN.
As with the small system example, site performance
will be optimized through the careful selection and
placement of Area Controller Routers and the Area
Controller to form efficient clusters. Building layout
and materials will also play some role in determining
the best solution to deliver a highly effective means of
testing and maintenance requirements.
9
EX3F
EX35
C8ES35
LPEX-50
LPEX300
PREMIER
LPEX-XP
EXP
LPEX54
EXIT
SIGNS
TABLE OF CONTENTS
Project/Location:
MR16 LED EMERGENCY LIGHTING
Contractor:
Date:
Prepared by:
MR16 LED ILLUMINATION
MR16 LED LAMP BENEFITS
With the remarkable technology development in the last
decade, the light-emitting diode (LED) is becoming the
preferred solution in low- and medium-power lighting
applications. The emergency lighting industry is no
exception: today virtually every new product introduced to
market includes “white” LEDs for emergency illumination.
• CSA C22.2 No. 141 certified.
• Energy-efficient LED MR16 lamp provides equivalent
lighting performance to a much higher watt halogen
MR16 lamp.
• Reduces required battery capacity by 75%, providing
necessary illumination with fewer remote heads and
battery units for project cost savings.
Extremely efficient and long-lasting, LED lamps become the
natural alternative to incandescent lamps due to three main
advantages:
• Small profile, compact white lighting is ideal for
architectural applications.
• = lamp efficacy: 50 - 70 lumen per watt compared to 15 30 lumen per watt of the best halogen lamp.
• Vibration-resistant LED stands up to industrial
environments.
• = operational life: 30,000+ hours, equivalent to a lifetime
warranty in emergency lighting.
• Ideal for indoor and outdoor use.
• = lower lamp temperature (80 - 120°C) is a huge benefit
for lighting in hazardous locations.
340-LUMEN 5W MR16 LED
200-LUMEN 4W MR16 LED
Keeping pace with technology, in 2012 we introduced a
12V-5W MR16 LED lamp. With a typical luminous flux of 340
lumens, this lamp has the same lighting performance as
a 20W high-output halogen MR16. A twin emergency head
installed at a height of 7.5ft illuminates more than a 70ft
path of egress.
Leading the technology trend, Emergi-Lite® offers a
complete series of 4W MR16 LED lamps available for all
the standard battery voltages: 6V, 12V, 24V and 120V. With
up to 30,000 hours of operational life and a luminous
flux of typically 200 lumens, they are available with most
emergency heads designed to hold an MR16 lamp and meet
the majority of illumination specifications. For example: one
pair of LED emergency heads installed at a height of 7.5ft,
illuminates a 6ft by 40ft path of egress.
510-LUMEN 6W MR16 LED
New in Fall 2013, we intoduce a 12V - 6W MR16 LED lamp,
which offer typical luminous flux of 510 lumens. Like the
lower wattage MR16 LED lamps, this new lamp is specially
designed for emergency lighting. It offers the same lighting
preformance as the 35W or 20W Mr16 IR. A twin emergency
head installed at a height of 7.5’ illuminates approximately
100’ path of egress.
Compared to halogen lamps (16-20W), these 4W MR16
LED lamps illuminate the same area of egress during an
emergency situation by using 75% less power. This has
a direct impact on the battery size, reducing the back-up
capacity needs by 75%. Consequently, it also reduces the
total cost of the application, with the use of smaller battery
capacity units, the possibility of using fewer fixtures due to
superior illumination, thus also reducing electrical wiring,
and it it reduces the environmental footprint.
40-FT. PATH OF EGRESS 2 X 4W MR16 LED
70-FT. PATH OF EGRESS 2 X 5W MR16 LED
6
INTRODUCTION
EDE SERIES
EX30 SERIES
EAE SERIES
EX3 SERIES
C8SR3 SERIES
EX3F SERIES
C8SR35 SERIES
P.14-15
P.16-17
P.18-19
P.20
P.21
P.22
P.23
P.24
C8ES35/SE35
SERIES
C8E/S35R
SERIES
PRE SERIES
LPEX100 SERIES
LPSR100 SERIES
LPEX300 SERIES
LPSR300 SERIES
C8ES300 SERIES
P.25
P.26
P. 27
P. 28
P. 29
P. 30
P. 31
P. 32
EA SERIES
LPEX50 SERIES
C8SR50 SERIES
LPEX SERIES
LPEX54 SERIES
C8ES70/SE70
SERIES
ES70B12/SE
SERIES
EAC SERIES
P. 33
P. 34
P. 35
P. 36
P. 37
P. 38
P. 39
P. 40-41
LPEX50-P
SERIES
C8SR50-P
SERIES
ES SERIES
EX10 SERIES
C8SR10 SERIES
C8ES10/SE10
SERIES
ESC SERIES
EX10-P & LPEX10-P
SERIES
P. 42
P. 43
P. 44
P. 45
P. 46
P. 47
P. 48
P. 49
SR SERIES
12ESL-EX
SERIES
12ESL-SR SERIES
EP SERIES
PREMIER EXIT
SERIES
PREMIER COMBO
SERIES
C8SRPK SEIRES
C8ESPK/SEPK
SERIES
P. 50-51
P. 52
P. 53
P. 54
P. 55
P. 56-57
P. 58
P. 59
C8SRPK-P
SERIES
EN SERIES
LPEX600 SERIES
ENC SERIES
LPEX600-N SERIES
EH SERIES
LPEXHZ SERIES
EHC SERIES
P. 60-61
P. 62
P. 63
P. 64
P. 65
P. 66
P. 67
P. 68-69
EXHZ SERIES
EX SERIES
LPEX-XP SERIES
C8SRXP SERIES
EXP SERIES
EXP SERIES
ET SERIES
SPECIAL WORDING
P. 70-71
P. 72-73
P. 74-75
P. 76-77
P. 78-79
P. 80-81
P. 82
P. 83
GLOSSARY
U
Auto-diagnostic
UN
Auto-diagnostic
(non-audible)
CT
CW1
CW3
L
Automatically tests and continuously monitors your emergency lighting unit . If a problem occurs, the unit will send a visual
(flashing or blinking LED indicator) and audible warning . Complies with Fire Code requirements .
Automatically tests and continuously monitors your emergency lighting unit . If a problem accurs, the unit will send a visual
(flashing or blinking LED indicator) warning . Complies with Fire Code requirements .
Cab-tire
Unit supplied with a cab-tire cable used for special hardwire applications .
Cold weather, 120VAC
120VAC input cold weather protection feature for applications where temperatures can reach -40° C .
Cold weather, 347VAC
Line cord (120V)
347VAC input cold weather protection feature for applications where temperatures can reach -40° C .
When ordering a battery unit with the LC option, we supply and pre-install a line cord with a standard 3 prong 120V plug .
Just hang the fixture and plug it in to a standard receptacle! Only available on 120V units .
A protective teflon coating that is applied to the glass lens of a lighting fixture to prevent broken shards from falling in the
event the glass is accidently broken or vandalised .
FP
Teflon coated lens
X2
Remote test receiver
Used to perform maintenance tests by means of radio receiver in conjunction with a transmitter (HHC option) on battery
units that are out of reach . Simply point the receiver at the unit .
NEXUS® system interface
The NEXUS® system interface is a computerized maintenance system for emergency lighting that, once programmed, will
perform the tests, keep written records and send a notification if anything needs to be fixed . One full system can address
hundreds of units in as many buildings as you need from a single location .
NEX
D3
Time delay (15 minutes)
Normally, when the AC power is restored, all emergency lighting lamps are turned off . However, in some cases, such as
when metal halide lamps are used, it is possible that the general lighting will not be available for several minutes after the
blackout (or brownout) period . Battery units with the D3 option will keep some energy in store to ensure that the emergency
lighting stays on or comes back on for at least 15 minutes once the regular AC power has been restored .
Time delay
(programmable)
Same as the D3 option but can be programmed for 5, 10 or 15 minutes delay .
TP
Tamper-proof screws
Screws that require a special bit . Can be used on certain units to deny access to unauthorized personnel .
TL
Twistlock plug
Used to facilitate the connection and removal of battery units for maintenance purposes .
D
89
RETROFIT KITS
PENDANT KIT
WIRE GUARDS
EZ2 CANOPY
GLOSSARY
P. 84-86
P. 87
P. 88-89
P. 90
P. 91
13
Project/Location:
Contractor:
EXIT SIGNS OVERVIEW
Date:
Prepared by:
Electrical Exit Signs (connected to a source of power) differ
from battery units in that they shall be illuminated at all
times during normal AC operation, and not only upon loss
of AC power. This has a direct impact on the admissible
energy consumption referenced in government regulations
(National Resources Canada NRCan, CSA C-860), which is a
maximum of 5W per legend single or double face. A legend
is defined as a single word, either “SORTIE” or “EXIT”. There
are also bilingual Exit Signs with: “SORTIE EXIT” or “EXIT
SORTIE”, quite common in applications such as airports or
federal buildings. A bilingual Exit Sign is acceptable up to
a maximum of 10W. The legend must also meet visibility
standards including: lettering dimensions (minimum
150mm height, etc.), average brightness, uniformity, and
lettering/background contrast ratio. The most popular light
source is based upon solid state LED technology, which is
capable of meeting both lumen output and energy
efficiency requirements.
In addition to electrical Exit Signs, there are power free,
self-luminous signs, incorporate radioactive materials such
as tritium gas as a light source.Their brightness level is
very low, that is 2-3% of the minimum level required for an
electrical sign. However, they are safer and easier to install
in hazardous/explosion-proof environments such as coal
mines, natural gas installations, etc. As these signs are not
electrical signs, they are not subject to CSA standards such
as C860-07.
BACK-LIT AND EDGE-LIT EXIT SIGNS
EXPLOSION-PROOF ENVIRONMENT EXIT
SIGNS
COMBINATION UNITS
A well established fixture type, the combination unit or
“combo”, includes both a small battery-powered Emergency
Lighting unit and an AC/DC Exit Sign. An economical and
easy to install alternative (installs to a single electrical box),
the combo offers both an Exit Sign indicating the direction of
egress as well as emergency lighting on the path of egress.
Two different methods are used to illuminate the legend.
The most common is found in back-lit signs, which use a
light source located behind the legend, illuminated through
a red diffuser panel. The other method uses a clear, white
or mirrored plastic (acrylic) face panel on which the legend
is etched or silkscreened. The light source is installed in the
top portion of the panel. Light is transmitted from the top
edge of the panel, which is where the “Edge-Lit” Exit Sign
gets its name from. In general, back-lit Exit Signs are more
economical and provide more uniform illumination of the
legend. On the other hand, acrylic Edge-Lit Exit Signs are
considered more high-end, elegant fixtures.
Does CSA C860 standard apply to all Exit Signs, and in all
applications? Actually, there are no exceptions. Compliance
is required in all cases, even though the solution may be
hard to find. For example, equipment for use in hazardous
locations, such as areas classified under Class I, Division
1 (or Class I, Zones 0 and 1), defined as locations where
flammable gases, vapors or liquids are present frequently
or under normal operating conditions.
Required luminaires are designed specifically to meet CSA
standards for explosion-proof equipment. The heavyduty luminaires are rated for lamp wattages ranging
from 50-250W. Constructed of die-cast aluminum, the
units feature a resistant prismatic glass globe providing
hemispherical light distribution. Until now, because of
these characteristics, traditional Exit Signs were using
15-25W incandescent lamps in order to provide sufficient
illumination of the legend. Conversely, an LED Exit Sign is
typically rectangular and relatively thin (4-8cm) with an axial
light source consisting of a line of LEDs to provide indirect
illumination of the legend through multiple reflections. So,
how is it possible to develop an LED Exit Sign that meets
NRCan/CSA-C860 using a bulky heavy-duty luminaire
dedicated to hazardous locations Class I, Division 1?
BATTERY, REMOTE, AC AND OTHER POWER
SOURCES
Three types of fixtures are available for emergency lighting
applications. The first type is the Self-Powered Exit Sign,
with a rechargeable battery for emergency mode operation.
Next is the Remote Exit Sign, or AC/DC Exit Sign: in addition
to a normal AC power supply, it includes a DC input (6VDC,
12VDC, etc.) for remote power supplied by from a separate
battery backup. Installation of such Exit Signs requires DC
wiring between both fixtures. Finally, the AC-only Exit Signs
are for applications where emergency power is supplied
from an AC Central System. A variation on Exit Sign design
uses photo-luminescent materials for the legend (letters
and/or background). According to the National Building
Code, photo-luminescent Exit Signs must be continuously
illuminated by a dedicated light source connected to an
emergency power supply.
The Thomas & Betts R&D group has found a solution and
developed a special LED lamp series that is easy to install
in the lamp base of explosion-proof type luminaires. This
special LED lamp consumes less than 5W in either AC or
DC current of high performance ALINGAP LEDs configured
in a unique pattern. Horizontal distribution is 360 degrees
radially and vertical distribution is directly focused on the
sign legend.
14
Project/Location:
Contractor:
Date:
Prepared by:
The outstanding results of ALINGAP technology have
enabled the engineers at Thomas & Betts to design a new
generation of Exit Signs with sustained lighting performance
and reduced power consumption. The ALINGAP LED signs
have an initial level of legend illumination that is 35 to 50 %
higher than the severe requirements of CSA/C860 and UL924
standards.
This innovative design meets the visibility criteria on
standard size legends (EXIT 28cm x 15cm, SORTIE 42cm x
15cm), while limiting power consumption to between 3 to
4.7W per Exit Sign.
LED lamps are dedicated to various voltage ratings: 6V, 12V,
24V or 120V and operate on DC and AC, supplying power to
the Exit Sign from emergency lighting unit equipment or
central AC or DC systems. Lamps are listed/certified CSA
C-US to CSA T.I.L. B-69 and UL1993 standards for LED
technology based lamps or lamps with integral ballast.
This further reinforces the assurance of performance and
safety of the Exit Signs using these lamps. The new Exit
Sign series from Thomas & Betts includes fixtures designed
for installation in all hazardous location classifications:
Class I Divisions 1 and 2, Groups A, B, C and D; Class II
Divisions 1 and 2, Groups E, F, and G; Class III Divisions
1 and 2. Specifiers specialized in industrial lighting are
now assured that they can specify certified hazardous
location equipment also approved and compliant to
NRCan/CSA C-860 standards.Sustained R&D efforts in the
optoelectronics industry have lead to a new development in
LED manufacturing: “ALINGAP” technology. Based on the
compound of four elements: Aluminum, Indium, Gallium
and Phosphorous, it offers higher light efficacy, with the
lumen/watt ratio 300% to 500 % higher than the traditional
GaAs LED. In addition, the new technology also significantly
improves the maintained light output of the LED by utilizing
materials that operate at lower temperatures than the
previous generation of LEDs.
This increase will compensate for the expected 27% light
degradation over time, allowing the equipment to still
meet the visibility criteria more than ten years after field
installation.
Unlike other emergency lighting manufacturers, who only
guarantee equipment against functional defects,
Emergi-Lite® ALINGAP Exit Signs are designed for 10 years+
of CSA/UL photometric compliance.
Make sure your customer writes “ALINGAP LED” in his
specification for Exit Signs. This represents the best
assurance for Energy Efficiency, Long Life and Maintained
Performance.
Due to increased market awareness on the subject,
LED manufacturers have started to publish test results
and statistical data related to the light degradation
phenomenon. Among other data publicly available on
the Internet, an article from a leading semiconductor
manufacturer (*Agilent Technologies, Application Brief
I-018) describes the results of a High-Temperature
Operating Life (HTOL) test carried on ALINGAP LEDs
during a 16,000-hour time frame. Based on the test results,
the authors estimate that ALINGAP LEDs exposed to
100,000 hours (11.4 years) of continuous use at an ambient
temperature of +55°C would exhibit an overall light output
degradation of about 27%, which translates to an annual
loss rate 10 times lower than the average light loss of
traditional GaAs LEDs.
15
Project/Location:
Project/Location:
EDE Series
Contractor:
Contractor:
Date:
Die-Cast Aluminum Pictogram
Edge-Lit Sign
Date:
Prepared by:
Prepared by:
Lumacell Model:
TYPICAL SPECIFICATIONS
FEATURES
•S
elf-Powered models provide minimum 120 minutes of
emergency lighting
Supply and install the Emergi-Lite® EDE Series of Die-Cast
pictogram Edge-Lit signs.
• Die-Cast aluminum construction
When specified for surface mount, the unit shall come standard with a
trim plate, trim ring, back box and canopy made of Die-Cast aluminum
with
finish. The trim plate shall have a
profile and allow
for wall- or ceiling-mount installation. The trim ring shall allow for
semi-recessed installation in walls or ceilings with cavity. The canopy
shall allow for wall, end, or ceiling mount.
• Modular design offers great choice of architectural profiles
•U
niversal Die-Cast back-box for surface or semi-recessed
mounting on ceilings or walls
•L
ED strip module can be rotated in the unit for either wall or
ceiling mount
•F
lat Die-Cast trim plate and galvanized steel back-box for
recessed ceiling mount
• Clear acrylic panel with pictogram legend
•C
omes standard with double-face panels for use in single-face
and double-face applications
• White LED light source
•U
niversal AC input: two-wire 120 to 347VAC; universal DC input:
two-wire 6 to 24VDC
•E
nergy efficient – consumes less than 2.5W in AC and
DC-remote modes
• Meets or exceeds CSA 22.2 No.141-10
When specified for recessed ceiling-mount, the unit shall come
standard with a flat trim plate of Die-Cast aluminum with
finish, a back box of galvanized steel, and a hardware kit for back box
installation between ceiling joists. The back box shall be provided with
conduit knock-outs at the top, back and end.
All Edge-Lit units shall have the trim plate snap and lock in the
housing with torsion spring retainers, thereby eliminating any visible
screws or hardware. The legend shall be printed on a clear acrylic
panel. The panel shall come standard with double-face legend, for
single-face and double-face applications. The light source shall be
long-life white light-emitting diodes (LED) and shall provide even illumination in normal and emergency operation. The Edge-Lit sign shall
operate with universal 2-wire AC input voltage of 120 to 347VAC at less
than 2.5W and universal 2-wire DC input voltage from 6 to 24VDC at
less than 2.5W. The Edge-Lit sign in a Self-Powered
configuration shall use a sealed Nickel-Cadmium battery of 2.4V
nominal voltage and shall stay illuminated during emergency operation
for at least two hours upon AC failure.
When specified, the Self-Powered unit shall include non-audible
auto-test functions, managed by a micro-controller: it shall execute
automatic tests for 5 minutes every 30 days, 30 minutes every 60 days
and two hours annually. When a fault is detected a red flashing LED
shall identify the failure type: battery, charger circuitry, or LED lamps.
The Edge-Lit sign shall be listed CSA 22.2 No.141-10.
The equipment shall be Emergi-Lite® Model:
.
POWER CONSUMPTION
MODEL
AC SPECS
DC SPECS
AC-only
120 to 347VAC
Less than 2.5W
-
-
AC/DC standard
120 to 347VAC
Less than 2.5W
6 to 24VDC
Less than 2.5W
Self-Powered
120 to 347VAC
Less than 3.5W
Nickel-Cadmium battery
Minimum 2 hours
Self-Powered diagnostic
120/347VAC
Less than 3.5W
Nickel-Cadmium battery
Minimum 2 hours
16
Project/Location:
EDE Series
Contractor:
Date:
Die-Cast Aluminum Pictogram
Edge-Lit Sign
Prepared by:
DIMENSIONS
Dimensions are approximate and subject to change.
ANGULAR TRIM
4” [10.0 cm]
111/2” [29.2 cm]
27/8” [7.4 cm]
113/4” [29.8 cm]
67/8” [17.3 cm]
8” [20.3 cm]
1 ” [2.9 cm]
45/8” [11.6 cm]
21/2” [6.4 cm]
1/8
61/4” [15.7 cm]
45/8” [11.6 cm]
115/8” [29.6 cm]
163/4” [42.7 cm]
16” [40.8 cm]
93/4” [24.7 cm]
3 ” [8.3 cm]
4” [10.0 cm]
21/2” [6.4 cm]
27/8” [7.4 cm]
1/4
13” [32.9 cm]
CIRCULAR TRIM
4” [10.0 cm]
16” [40.8 cm]
111/2” [29.2 cm]
27/8” [7.4 cm]
8” [20.3 cm]
67/8” [17.3 cm]
61/4” [15.7 cm]
45/8” [11.6 cm]
21/2” [6.4 cm]
113/4” [29.8 cm]
1 ” [2.9 cm]
93/4” [24.7 cm]
4 ” [11.6 cm]
5/8
115/8” [29.6 cm]
163/4” [42.7 cm]
1/8
4” [10.0 cm]
3 ” [8.3 cm]
21/2” [6.4 cm]
27/8” [7.4 cm]
1/4
13” [32.9 cm]
FLAT TRIM
37/8” [9.9 cm]
15” [38.1 cm]
37/8” [9.9 cm]
6” [17.8 cm]
67/8” [17.4 cm]
31/4” [8.3 cm]
13” [32.9 cm]
ORDERING INFORMATION
SERIES
FACES/ARROW
EDE= die-cast edge-lit
pictogram exit sign
1= one face, no arrows
L= arrow left, single face
R= arrow right, single face
2= two face, no arrows
A= universal two, arrow left or right
COLOUR
rushed
A= b
aluminum
B= black
C= chrome
P= polished brass
W= factory white
Z= bronze
TRIM
A= angular
C= circular
F= flat
(fully recessed)
VOLTAGE
AC= AC only, 120 to 347VAC
U= 120 to 347VAC, 6 to 24VDC
U48= 120 to 347VAC, 48VDC
UI= Self-Powered, 120 to 347VAC
ID= Self-Powered (non-audible), 120/347VAC
ID2= Self-Powered (non-audible), 120/277VAC
NEX= Nexus® system interface**
NEXRF= wireless Nexus® system interface**
**Consult your sales representative for options
available with the Nexus® system
EXAMPLE: EDE2ACU
Unlike EXIT signs, the pictogram sign is not available in double arrow configurations.
17
Project/Location:
EX30 Series
Contractor:
Date:
Die-Cast Edge-Lit
Exit Sign
DESIGN UPGRADE INTRODUCING NEW FEATURES:
Prepared by:
TYPICAL SPECIFICATIONS
Supply and install the Emergi-Lite® EX30 Series of Die-Cast
Edge-Lit Exit Signs.
1. E
asier installation: component-free back-box housing and
canopy can be installed in advance, like a regular junction box.
The unit specified for universal mounting shall come standard with
a trim plate, trim ring, back box and canopy all made of die-cast
aluminum with _____ finish. The trim plate shall have a _____
profile and allow for wall- or ceiling-mount installation. The trim
ring shall allow for recessed installation in walls or ceilings with
cavity. The canopy shall allow for wall, end, or ceiling mount. The
back box shall be provided with conduit knock-outs at the top, back
and end.
2. 2 0 – 30% less power consumption: max. 1.4W (AC-only
models) and max. 2.5W (self-powered)
3. B
i-color LED pilot light allows visual diagnostic without need
to open the unit (self-test and diagnostic option)
4. Listed by CSA
5. Also available with white LEDs for custom-design
legends: pictograms, special wording, etc. (ask our sales
representatives)
The unit specified for recessed ceiling shall come standard with a
flat trim plate of Die-Cast aluminum with _____ finish, and a back
box of 20-gauge galvanized steel. The back box shall be provided with
conduit knock-outs at the top, back and end.
FEATURES
All models shall be provided with a hardware kit including two 27”
adjustable bar hangers for back box recessed installation.
• Die-Cast aluminum construction
• Modular design for universal mounting
The unit shall have the trim plate snap and lock in the housing with
torsion spring retainers, thereby eliminating any visible screws or
hardware. The legend shall be printed on a clear acrylic panel.
The panel shall have a U-shape and the legend shall have precision
etched 6” high and 3/4” stroke red letters with laser-edged contour
and with a white, clear or mirror background. The light source shall
be long-life light-emitting diodes (LED) and shall provide even
illumination in normal and emergency operation. Red LED
technology shall be ALINGAP. The unit shall operate with two-wire
universal AC input voltage from 120 to 347VAC and two-wire
universal DC input from 6 to 24VDC, each input at less than 1.4W.
•T
rim plate choices: pyramid or round for universal mounting
and flat (recessed ceiling)
• Component-free back-box ready to pre-install
•L
ED strip module can be rotated in the unit for either wall or
ceiling mount
•U
-shaped clear acrylic panel with laser-etched contour for
legend letters
• Long-life LED light source; red LEDs of ALINGAP technology
• Two-wire universal AC input: 120 to 347VAC 50/60Hz
The Edge-Lit sign in a Self-Powered configuration shall use a sealed
Nickel-Cadmium battery and shall stay illuminated during
emergency operation for at least 90 minutes upon AC failure.
• Sealed, maintenance-free Nickel-Cadmium battery
• Meets or exceeds CSA 22.2 No.141-10
The Self-Powered unit with self-test and silent diagnostic functions
shall be managed by a micro-controller: it shall execute automatic
tests for one minute every 30 days, 30 minutes every 60 days and 90
minutes annually. A diagnostic circuit shall continuously monitor the
performance of the battery, charger module and LED lamps. When
a fault is detected the pilot light shall change colour from green to
red and flash with a specific code. The red light is steady-on in case
of battery disconnect; it will flash with one blink for battery failure,
two blinks for charger failure and four blinks for LED lamp failure. A
label with the diagnostic legend shall be visible next to the pilot light.
The Edge-Lit sign shall be certified CSA C22.2 No.141 and CSA-C860.
The Exit Sign shall be Emergi-Lite® Model:
.
POWER CONSUMPTION
MODEL
AC SPECS
DC SPECS
AC-only
120 to 347VAC
Less than 1.4W
AC/DC - remote
120 to 347VAC
Less than 1.4W
6 to 24VDC
Less than 1.4W
Self-Powered
120 to 347VAC
Less than 2.3W
Nickel-Cadmium battery
Minimum 90 minutes
Self-Powered diagnostic
120/347VAC
Less than 2.3W
Nickel-Cadmium battery
Minimum 90 minutes
18
-
Project/Location:
EX30 Series
Contractor:
Date:
Die-Cast Edge-Lit
Exit Sign
Prepared by:
DIMENSIONS
Dimensions are approximate and subject to change.
163/4” [42.7 cm]
4” [10.0 cm]
16” [40.8 cm]
45/8” [11.6 cm]
121/8” [30.9 cm]
27/8” [7.4 cm]
85/8” [21.9 cm]
71/2” [19.0 cm]
123/8” [31.5 cm]
21/2” [6.4 cm]
61/4” [15.7 cm]
11/8” [2.9 cm]
4” [10.0 cm]
45/8” [11.6 cm]
121/4” [31.3 cm]
27/8” [7.4 cm]
105/8” [27.1 cm]
3 ” [8.3 cm]
1/4
21/2” [6.4 cm]
DIE-CAST EDGE-LIT
13” [32.9 cm]
DIE-CAST RECESSED EDGE-LIT
37/8” [9.9 cm]
71/2” [19 cm]
75/8” [19.4 cm]
37/8” [19.9 cm]
31/4” [8.3 cm]
15” [38.1 cm]
13” [32.9 cm]
ORDERING INFORMATION
SERIES
EX3
FACES
1= single
face
2= double
face
HOUSING
COLOUR
B= black
BA= brushed
aluminum
BR= bronze
CH= chrome
olished
PB= p
brass
W= factory
white
FUNCTION
A= AC only, 120 to 347VAC
U=120 to 347VAC, 6 to 24VDC
I= Self-Powered diagnostic,
120/347VAC
D= Self-Powered, 120 to 347VAC*
D2= Self-Powered diagnostic,
120/277VAC
NEX= NEXUS® system interface**
NEXRF= wireless NEXUS® system
interface**
LEGEND
COLOUR
R= red
G= green
* Self-Powered (90 Min time base)
** Consult your sales representative for
options available with the NEXUS®
system.
EXAMPLE: EX31WURWA
19
BACKGROUND
COLOUR
C= clear single face
M= mirror
W= white
CHEVRONS
TRIM OPTION
N= no chevrons
AL= chevron left
AR= chevron
right
A= one chevron,
double face
DA= double
chevron,
double face
A= angular, universal
mount
C= circular, universal
mount
F= flat trim, ceiling
mount, recessed only
Project/Location:
Contractor:
EAE Series
Date:
Aluminum Slim Edge-Lit
Pictogram Sign
Prepared by:
TYPICAL SPECIFICATIONS
FEATURES
Supply and install the Emergi-Lite® EAE Series slim-profile pictogram
Edge-Lit Exit Sign. The unit shall operate with universal 2-wire AC
input voltage of 120 to 347VAC at less than 3W and universal 2-wire
DC input voltage from 6 to 24VDC at less than 2.5W. The housing
assembly shall be constructed of extruded aluminum with textured
finish and
colour. The canopy shall be of Die-Cast aluminum
and allow for wall, end, or ceiling mount. The legend shall be printed
on a pure-acrylic panel. The panel shall come standard with doubleface legend, for single-face and double-face applications. The light
source shall be long-life white light-emitting diodes (LED) and shall
provide even illumination in normal and emergency operation. The
pictogram Edge-Lit Exit Sign in a Self-Powered configuration shall
use a sealed Nickel-Cadmium battery of 2.4V nominal voltage and
shall stay
illuminated during emergency operation for at least two hours upon
AC failure.
• Slim-profile extruded aluminum housing
• Low-profile EZ2 Die-Cast aluminum canopy
• Universal surface mounting – wall, ceiling or end mount
•C
lick-to-open housing door allows easy access to the panel and
electrical wiring
• Extruded acrylic panel with pictogram legend
•C
omes with double-face panels for use in single-face and
double-face applications
• Long-life white LED light source
• Meets or exceeds CSA.222 No.141-10
•U
niversal AC input: two-wire 120 to 347VAC; standard DC input:
two-wire 6 to 24VDC
•E
nergy efficient – consumes less than 3W in AC or DC-remote
mode
The pictogram Edge-Lit Exit Sign shall be listed CSA 22.2 No.141-10.
•S
elf-Powered models provide minimum two hours of
emergency lighting
The equipment shall be Emergi-Lite® Model:
.
DIMENSIONS
Dimensions are approximate and subject to change.
DC SPECS
AC-only
Less than
3W
-
-
AC/DC
standard
120 to
347VAC
Less than
3W
6 to 24VDC
Less than
2.5W
AC/48VDC
120 to
347VAC
Less than
3W
48VDC
2W
AC/120VDC
120 to
347VAC
Less than
3W
120VDC
4.7W
Two-wire
120V AC/DC
120VAC
Less than
3.5W
120VDC
Less than
3.5W
Nickel-Cadmium
battery
Minimum 2
hours
Self-Powered 120 to 347VAC Less than 4W
95/8” [24.4 cm]
AC SPECS
120 to
347VAC
< PICTOGRAM
LEFT FROM HERE
PICTOGRAM >
RIGHT FROM HERE
41/4” [10.7 cm]
12” [30.5 cm]
101/8” [25.7 cm]
MODEL
105/8” [27.0 cm]
POWER CONSUMPTION
121/2” [31.9 cm]
103/4” [27.3 cm]
105/8” [27.0 cm]
15/8” [4.2 cm]
PICTOGRAM
STRAIGHT FROM
HERE
ORDERING INFORMATION
SERIES
EAE= extruded aluminum edge-lit pictogram
exit sign
FACES / ARROW
(UNIVERSAL MOUNTING)
1= one face, no arrow
L= single face left arrow
R= single face right arrow
2= two faces, no arrow
A= two faces, arrow left or right
COLOUR
TA= textured aluminum
OW= off-white
VOLTAGE
AC= 120 to 347VAC only
U= 120 to 347VAC; 6 to 24VDC
UI= 120 to 347VAC Self-Powered*
U48= 120 to 347VAC; 48VDC
U120= 120 to 347VAC; 120VDC
2120= 2 wires 120VAC/VDC
*Self-Powered (90 min. time base)
EXAMPLE: EAE2OWAC
20
Project/Location:
EX3 Series
Contractor:
Date:
Aluminum Slim
Edge-Lit Exit Sign
Prepared by:
FEATURES
TYPICAL SPECIFICATIONS
• E xtruded aluminum housing
Supply and install the Emergi-Lite® EX3 Series LED slim-profile Edge-Lit
Exit Sign. The unit shall operate with universal two-wire AC input voltage
from 120VAC to 347VAC at less than 1.5W and universal two-wire DC input
voltage from 6VDC to 24VDC at less than 1.5W for single and double face
legends.
• Die-Cast aluminum E22 canopy
• Universal surface mounting: wall, ceiling or end mount
•C
lick-to-open housing door allows easy access to the panel and
electrical wiring
The housing assembly shall be fabricated of extruded aluminum with
a textured finish and
colour. The canopy shall be of die-cast
aluminum and allow for ceiling, wall, or end mount installation. The
light source shall be ten (10) long-life LEDs installed on a PCB strip.
Red LED technology shall be ALINGAP. The acrylic panel shall have a
curved contour.
• A crylic panel with curved contour
• Legend with 6” letters and easy to add-on directional indicators
•S
imple, two-wire universal AC input (120V to 347VAC 50/60Hz)
prevents installation errors
• Simple, two-wire universal DC input: 6V to 24VDC
The legend shall have 6” high, 3/4” stroke red letters on a clear
background, unless otherwise specified. The unit shall be equipped with
stick-on translucent directional indicators, to be installed in the field as
required by the code.
•E
nergy efficient power consumption: less than 1.5W in AC or DC
mode
• Meets or exceeds CSA 22.2 No.141-10
The Exit Sign in a Self-Powered configuration shall be equipped with
sealed Nickel-Cadmium batteries and will provide a minimum of 90
minutes of emergency illumination upon AC failure.
POWER CONSUMPTION
MODEL
The equipment shall be CSA 22.2 No.141-10 approved.
AC SPECS
AC/DC red
120 to 347VAC
Less than
1.5W
6 to 24VDC
Less than
1.5W
AC/DC
green
120 to 347VAC
Less than
2W
6 to 24VDC
Less than
1.5W
SelfPowered
red
120 to 347VAC
Less than
2.5W
Nickel-Cadmium
battery
Min. 90
minutes
Less than 3W
Nickel-Cadmium
battery
Min. 90
minutes
Self-Powered
120 to 347VAC
green
The equipment shall be Emergi-Lite® Model:
DC SPECS
DIMENSIONS
Dimensions are approximate and subject to change.
121/2” [31.8 cm]
41/4” [10.7 cm]
12” [30.5 cm]
15/8” [4.2 cm]
101/2” [26.6 cm]
101/8” [25.6 cm]
CEILING MOUNT
111/4” [28.6 cm]
END MOUNT
12” [30.5 cm]
111/8” [28.2 cm]
WALL MOUNT
ORDERING INFORMATION
SERIES/FACES
EX38= single face
EX39= double face
HOUSING COLOUR
TA= textured aluminum
OW= off-white
VOLTAGE
-AC= AC only
-U= AC/DC
-UI= Self-Powered (90 minutes)
-EM120-2W= 120VAC, 120VDC, 2 wires
Other colours available,
Consult your sales represnatative.
FACEPLATE COLOURS
-RC= red/clear*
-RW= red/white
-RM= red/mirror
-GC= green/clear*
-GM= green/mirror
*Not available on double face.
EXAMPLE: EX38TA-U-RC
21
.
Project/Location:
C8SR3 Series
Contractor:
Date:
Aluminum Slim
Edge-Lit “Sortie” Sign
FEATURES
Prepared by:
TYPICAL SPECIFICATIONS
• Extruded aluminum housing
Supply and install the Emergi-Lite® C8SR3 Series LED slim-profile
Edge-Lit “Sortie” Sign. The unit shall operate with universal two-wire
AC input voltage from 120VAC to 347VAC at less than 2W and universal
two-wire DC input voltage from 6VDC to 24VDC at less than 1.5W for
single and double face legends.
• Slim-Profile cast aluminum canopy
• Universal surface mounting: wall, ceiling or end mount
•C
lick-to-open housing door allows easy access to the panel and
electrical wiring
The housing assembly shall be fabricated of extruded aluminum with
a textured finish and
colour. The canopy shall be of Die-Cast
aluminum and allow for ceiling, wall, or end mount installation. The
light source shall be fourteen (14) long-life LEDs installed on a PCB
strip. Red LED technology shall be ALINGAP. The acrylic panel shall
have a curved contour.
• Acrylic panel with curved contour
• Legend with 6” letters and easy to add-on directional indicators
•S
imple, two-wire universal AC input (120V to 347VAC 50/60Hz)
prevents installation errors
• Simple, two-wire universal DC input: 6V to 24VDC
The legend shall have 6” high, 3/4” stroke red letters on a clear
background, unless otherwise specified.
•L
ong-life LED light source of ALINGAP technology assures low
maintenance costs
•S
elf-Powered models provide 90 minutes of emergency
illumination
The unit shall be equipped with stick-on translucent directional
indicators, to be installed in the field as required by the code. The Exit
Sign in a Self-Powered configuration shall be equipped with sealed
Nickel-Cadmium batteries and will provide a minimum of 90 minutes
of emergency illumination upon AC failure.
• CSA certified, meets or exceeds CSA 22.2 No. 141 requirements
The equipment shall be CSA 22.2 No. 141 approved.
•E
nergy-efficient power consumption: less than 3W in AC or DC
mode
The equipment shall be Emergi-Lite® Model:
POWER CONSUMPTION
MODEL
AC SPECS
DC SPECS
AC/DC
120 to 347VAC
Less
than 2W
Self-Powered
120 to 347VAC
Less
than 3W
6 to 24VDC
Less than
1.5W
Nickel-Cadmium
battery
Min. 90
minutes
DIMENSIONS
Dimensions are approximate and subject to change.
177/8” [45.3 cm]
183/8” [46.6 cm]
CEILING MOUNT
41/4” [10.7 cm]
177/8” [45.3 cm]
15/8” [4.2 cm]
11” [27.9 cm]
101/2” [26.6 cm]
115/8” [29.6 cm]
END MOUNT
111/2” [29.2 cm]
WALL MOUNT
ORDERING INFORMATION
SERIES
C8SR38= single face
C8SR39= double face
HOUSING COLOUR
TA= textured aluminum
OW= off-white
VOLTAGE
-AC= AC only
-U= universal (AC/DC)
-UI= Self-Powered (90 Minutes)
Other colours available.
Consult your sales representative.
FACEPLATE COLOURS
-RC= red/clear*
-RW= red/white
-RM= red/mirror
*Single face only.
EXAMPLE: C8SR38TA-AC-RC
22
Project/Location:
EX3F Series
Contractor:
Date:
Low-Profile Recessed
Edge-Lit Exit Sign
Prepared by:
FEATURES
TYPICAL SPECIFICATIONS
• Equipped with bar hanger kit for easy installation
The Emergi-Lite® EX3F Series combines a low-profile modular
design with state-of-the-art technology and ease of installation.
Elegantly discreet, these Exit Signs complement interior designs
while providing mounting versatility and energy efficiency.
• Rugged, 20-gauge steel back box
• Formed steel flat trim plate
• Choice of finishes: textured aluminum or off-white
Supply and install the Emergi-Lite® EX3F Series LED low-profile
recessed Edge-Lit Exit Sign. The unit shall operate with universal
two-wire AC input voltage from 120VAC to 347VAC at less than 1.5W
and universal two-wire DC input voltage from 6VDC to 24VDC at less
than 1.5W for single and double face legends. The housing assembly
shall be of rugged 20-gauge steel and shall include a bar hanger kit
for easy installation. The trim plate shall be low-profile and
manufactured of formed steel with a textured finish and _____ colour.
The light source shall be eight (8) long-life LEDs installed on a PCB
strip. Red LED technology shall be ALINGAP. The whole electrical
circuit shall be contained in a plastic housing fixed on the trim plate.
The acrylic panel shall have a curved contour. The legend shall
have 6” high, 3/4” stroke red letters on a clear background, unless
otherwise specified. The unit shall be equipped with stick-on
translucent directional indicators, to be installed in the field as
required by the Code.
•A
crylic panel with curved contour provides superior clarity and
illumination
• Legend with 6” letters and easy to add-on directional chevrons
• Choice of legend background: clear, white or mirror
•S
imple, two-wire universal AC input (120V to 347VAC 50/60Hz)
prevents installation errors
• Simple, two-wire universal DC input: 6V to 24VDC
• Long-life
LED light source of ALINGAP technology assures low
maintenance costs
• Energy-efficient power consumption: less than 1.5W in AC or DC mode
•S
elf-Powered models provide 90 minutes of emergency
illumination
•C
SA certified, meets or exceeds C860-01 and NRCAN/C860-01
requirements
• Meets or exceeds CSA22.2 No. 141-10
The Exit Sign in a Self-Powered configuration shall be equipped with
sealed Nickel-Cadmium batteries and will provide a minimum of 90
minutes of emergency illumination upon AC failure.
DIMENSIONS
The equipment shall be CSA-C860 and NRCAN/C860-01 approved.
CSA22.2 No. 141-10
The equipment shall be Emergi-Lite® Model:
.
Dimensions are approximate and subject to change.
16” [40.6 cm]
41/4” [10.8 cm]
151/8” [38.3 cm]
33/8” [8.5 cm]
MODEL
33/8” [8.6 cm]
71/8” [18.1 cm]
7” [17.7 cm]
POWER CONSUMPTION
AC SPECS
120 to 347VAC
Less than
1.5W
AC/DC-remote 120 to 347VAC
Less than
1.5W
6 to 24VDC
Less than
1.5W
Self-Powered
Less than
2.5W
Nickel-Cadmium
battery
Min. 90
minutes
AC-only
113/4” [29.7 cm]
DC SPECS
120 to 347VAC
-
ORDERING INFORMATION
SERIES / FACES
EX38F= single face
EX39F= double face
HOUSING COLOUR
VOLTAGE
TA= textured aluminum
OW= off-white
-U= AC/DC
-AC= AC Only
-UI= Self-Powered (90 Minutes)
PANEL COLOUR
-RC= red/clear*
-RW= red/white
-RM= red/mirror
-GC= green/clear*
-GM= green/mirror
*Single face only.
EXAMPLE: EX38FTA-U-RC
23
Project/Location:
Contractor:
C8SR35 Series
Date:
Edge-Lit “Sortie” Sign
Prepared by:
FEATURES
TYPICAL SPECIFICATIONS
• Universal
back box designed for surface or recessed mounting on
ceilings or walls
Supply and install the Emergi-Lite® C8SR35 Series LED “SORTIE’’
Exit Sign.
• Modular
retainer clips allow “snap-in” installation of face panel
after installation of back box
The equipment shall operate with universal two-wire AC input voltage
from 120VAC to 347VAC at less than 4.5W and universal two-wire
DC input voltage from 6VDC to 48VDC at less than 2.5W for single
or double face legend. The housing assembly shall be fabricated of
die-cast aluminum and consist of a universal die cast aluminum back
box. The back box shall be provided with conduit knockouts on top,
back, and end. The trim plate shall have a round shape and attach to
the housing assembly with two (2) torsion spring retainers, thereby
eliminating all visible screws or hardware. The LED light strip shall
be contained within the trim plate.
• Extruded acrylic panels with precision-etched lettering legend
• LED
strip design allows for rotation for either ceiling or wall
mounting
• Long-life, energy-efficient ALINGAP technology LED light source
reduces maintenance and energy costs
• Energy efficient – consumes less than 5W in AC or DC mode
• Meets or exceeds C860 requirements
Red LED technology shall be ALINGAP. The polished acrylic face
panel shall have precision etched 6” high, 3/4” stroke red letters
with a white, clear or mirror background. For recessed applications,
please contact your regional sales representative .
• Meets or exceeds CSA22.2 No.141-10
POWER CONSUMPTION
MODEL
AC SPECS
DC SPECS
AC/DC red
120 to
347VAC
Less than
4.5W
6 to 48VDC
Less than
2.5W
Self-Powered
red
120 to
347VAC
Less than
5W
Nickel-Cadmium
battery
Min. 60
minutes
The Exit Sign in a Self-Powered configuration shall stay illuminated
during emergency operation for at least 60 minutes upon AC failure.
The Exit Sign shall be CSA 860 and CSA22.2 No. 141 approved.
The equipment shall be Emergi-Lite® Model:
.
DIMENSIONS
Dimensions are approximate and subject to change.
45/8” [11.6 cm]
27/8” [7.4 cm]
85/8” [21.9 cm]
113/8” [28.9 cm]
123/8” [31.5 cm]
61/4” [15.7 cm]
45/8” [11.6 cm]
121/4” [31.3 cm]
4” [10 cm]
21/2” [6.4 cm]
121/8” [30.9 cm]
233/8” [59.4 cm]
225/8” [57.5 cm]
31/4” [8.3 cm]
191/2” [49.7 cm]
181/2” [46.8 cm]
105/8” [27.1 cm]
C8SR36R
4” [10 cm]
WALL MOUNT RECESSED
11/8” [2.9 cm]
105/8” [27.1 cm]
21/2” [6.4 cm]
27/8” [7.4 cm]
137/8” [35.4 cm]
ORDERING INFORMATION
SERIES
C8SR36= single face
C8SR36R= recessed
single
face wall
mount, no
chevrons
C8SR37= double face
HOUSING COLOUR
W= factory white
BA= brushed aluminum
B= black
SUPPLY
-U= universal AC/DC
-UI= Self-Powered
EXAMPLE: C8SR36W-U-RC
24
FACEPLATE COLOURS
CHEVRONS
-RC= red/clear*
-RM= red/mirror
-RW= red/white
Blank= no chevrons
-AL= chevron left*
-AR= chevron right*
-DA= double chevron
-A= one chevron each
side, double face
*Single face only.
*Not available on double face
Project/Location:
C8ES35 & C8SE35
Series
Contractor:
Date:
Bilingual Edge-Lit Sign
Prepared by:
TYPICAL SPECIFICATIONS
FEATURES
•U
niversal back box designed for surface or recessed mounting on
ceilings or walls
Supply and install the Emergi-Lite® C8ES35 or C8SE35 Series LED
Edge-Lit sign. The equipment shall operate with universal two-wire
AC input voltage from 120VAC to 347VAC at less than 8.6W and
universal 2-wires DC input voltage from 6VDC to 48VDC at less than
4.5W for single and double face signs. The housing assembly shall
be fabricated of aluminum and consist of a universal aluminum
back box. The back box shall be provided with conduit knockouts
on top and back. The trim plate shall have a round shape and shall
attach to the housing assembly with two (2) torsion spring retainers
thereby eliminating all visible hardware. The LED light strip shall
be contained within the trim plate. Red LED technology shall be
ALINGAP.
•M
odular retainer clips allow “snap-in” installation of face panel
after installation of back box
•L
ED Edge-Lit, extruded acrylic face panels with precision-etched
lettering
•L
ED strip design allows for rotation for either ceiling or wall
mounting
•L
ong life, energy-efficient ALINGAP technology LED light source
reduces maintenance and energy costs
• Energy efficient – consumes less than 8.6W in AC or DC mode
The polished acrylic face panel shall have precision-etched 6” high,
3/4” stroke red letters with a white, clear or mirror background, with
the words EXIT and SORTIE side by side.
• CSA certified, meets or exceeds CSA 22.2 No. 141 requirements
POWER CONSUMPTION
MODEL
AC SPECS
The Exit Sign in a Self-Powered configuration shall stay illuminated
during emergency operation for at least 30 minutes upon AC failure.
DC SPECS
AC/DC red
120 to
347VAC
Less than
8.6W
6 to 48VDC
Less than
4.5W
Self-Powered
red
120 to
347VAC
Less than
8.6W
Nickel-Cadmium
battery
Min. 30
minutes
The Exit Sign shall be CSA-C860 and CSA22.2 No. 141 approved.
The equipment shall be Emergi-Lite® Model:
.
DIMENSIONS
Dimensions are approximate and subject to change.
4” [10 cm]
21/2” [6.4 cm]
27/8” [7.4 cm]
121/8” [30.9 cm]
45/8” [11.6 cm]
85/8” [21.9 cm]
61/4” [15.7 cm]
121/8” [30.9 cm]
45/8” [11.6 cm]
121/4” [31.3 cm]
31/4” [8.3 cm]
71/2” [19 cm]
C8ES35
313/8” [79.7 cm]
343/8” [87.2 cm]
61/4” [15.7 cm]
71/2” [19 cm]
121/8” [30.9 cm]
C8SE35
313/8” [79.7 cm]
343/8” [87.2 cm]
ORDERING INFORMATION
SERIES
FACES
C8ES= e
xit
sortie
C8SE= s ortie
exit
36= single face
37= double face
36R= recessed,
single face*
37R= recessed,
double face*
HOUSING
COLOUR
W= factory white
BA= brushed
aluminum
B= black
POWER SOURCE
-U= universal AC/DC,
6 to 48VDC
elf-Powered,
-I= S
120/347VAC
*Consult your sales
representative
FACEPLATE COLOUR
-RC= red/clear*
-RM= red/mirror
-RW= red/white
*Not available on double face.
EXAMPLE: C8ES36W-I-RC
25
CHEVRONS
Blank= no chevrons
-AL= chevron left
-AR= chevron right
-DA= double chevrons
-A= one chevron each side, double face
Project/Location:
Contractor:
C8E/S35R Series
Date:
Bilingual Square Edge-Lit Sign
FEATURES
Prepared by:
TYPICAL SPECIFICATIONS
• The
Edge-Lit front panels are fabricated of extruded acrylic,
with precision etched lettering
Supply and install the Emergi-Lite® C8E/S35R Series LED Edge-Lit
bilingual Exit Sign. The equipment shall operate with universal
two-wire AC input voltage from 120VAC to 347VAC at less than 4W and
universal two-wire DC input voltage from 6VDC to 48VDC at less than
2W for single or double face signs.
• Normal
AC operation and emergency
DC operation: 120-347VAC and 6-48VDC
• Also available in a Self-Powered configuration
The housing assembly shall be fabricated of Die-Cast aluminum and
consist of a universal die cast aluminum back box. The back box shall be
provided with conduit knockouts on top and in the back.
•L
ong life, energy-efficient ALINGAP technology LED light source
reduces maintenance and energy costs
• Meets or exceeds C860 requirements
The trim plate shall have an angular (prismatic) shape and attach to
the housing assembly with two (2) torsion spring retainers thereby
eliminating all visible hardware.
• Meets or exceeds CSA 22.2 No. 141 requirements
The LED light strip shall be contained within the trim plate. Red LED
technology shall be ALINGAP. The polished acrylic face panel shall
have precision etched 6” high, 3/4” stroke red letters with a white, clear
or mirror background, with the text ”EXIT” and “SORTIE” positioned
one on top of the other. When directional chevrons are specified, they
will be printed next to the word “EXIT”.
The Exit Sign specified for recessed applications will be supplied with a
flat trim plate.
POWER CONSUMPTION
MODEL
AC SPECS
DC SPECS
AC/DC red
120 to
347VAC
Less than
3W
6 to 48VDC
Less than
1.5W
Self-Powered
red
120 to
347VAC
Less than
3W
Nickel-Cadmium
battery
Min. 30
minutes
The bilingual Exit Sign in a Self-Powered configuration shall stay
illuminated during emergency operation for at least 30 minutes upon
AC failure.
The Exit Sign shall be CSA-C860 approved and meets CSA 22.2 No. 141
The equipment shall be Emergi-Lite® Model:
.
DIMENSIONS
Dimensions are approximate and subject to change.
163/4
16”" [42.7
[42.7cm]cm]
3
4
1
8
14 "cm]
[36.0cm]
141/8” [36
3
4
1
4
18" [45.6cm]
18” [45.6
cm]
" [44.9cm]
173/417
” [44.9
cm]
61/46” [15.7
cm]
" [15.7cm]
4" [10.0cm]
4” [10 cm]
1
4
" [41.2cm]
161/416” [41.2
cm]
5
8
1
2
1 ” [2.9 cm]
1
2
21/2” [6.4
cm]
2 " [6.4cm]
5
8
45/8” [11.6 cm]
4 " [11.6cm]
45/8”4 [11.6
cm]
" [11.6cm]
21/2
[6.4 cm]
2 "”[6.4cm]
1/8 1
18 " [2.9cm]
7
8
17177/8" ”[45.4cm]
[45.4 cm]
4”4"[10
cm]
[10.0cm]
16” [40.8
cm]
16" [40.8cm]
7
8
7
8
1
4
2 " [7.4cm]
27/8” [7.4
cm]
27/8
[7.4 cm]
2 "”[7.4cm]
31/4
[8.3 cm]
3 "”[8.3cm]
137/8
" [35.4cm]
13
” [35.4 cm]
7
8
ORDERING INFORMATION
SERIES
C8ES= exit/sortie
C8SE= sortie/exit
FACES
36B12=
single face
37B12=
double face
HOUSING COLOUR
W= factory white
BA= brushed aluminum
B= black
POWER SOURCE
Blank= universal AC/DC
to 48VAC
-I= Self-Powered
120/347 VAC
FACEPLATE COLOUR
RC= red/clear*
RW= red/white
RM= red/mirror
*Not available on double face.
EXAMPLE: C8E/S36RW-RC-AL
26
CHEVRONS
Blank= no chevrons
-AL= chevron left
-AR= chevron right
-DA= double chevron
-A= one chevron, each
side double face
Project/Location:
Contractor:
Date:
PRE Series
Prepared by:
Die-Cast LED Exit Sign
TYPICAL SPECIFICATIONS
FEATURES
• Housing of Die-Cast aluminum in a variety of finishes
Stylish, built of Die-Cast aluminum, the new PRE Series offers
superior workmanship, versatile mounting capabilities and
economical, long-lasting LED performance.
Supply and install the Emergi-Lite® PRE Series Exit Sign. The
frame, face plate(s), back plate and canopy shall be constructed of
Die-Cast aluminum of ______ finish and ______ color. No screws are
necessary to hold the faceplate(s) or the back plate to the housing.
The unit shall be suitable for installation on wall, end, or ceiling
mount. The faceplates shall come standard with knockout chevrons.
The light source shall be light emitting diodes (LEDs). Red LED
technology shall be ALINGAP. The LEDs shall provide illumination
in normal and emergency operation and shall be mounted inside
the exit housing, not on the face. An LED-sensitive diffuser shall
be mounted in front of the LEDs to provide the 6” high by ¾” stroke
letters with even illumination. The Exit Sign in a Self-Powered
configuration shall be equipped with a sealed, maintenance-free
Nickel-Cadmium battery. The equipment shall operate with a
dual-voltage input of 120/347VAC 60Hz with less than 3.5W of
consumption. The equipment shall stay illuminated at least 90
minutes upon AC failure. The Exit Sign shall be listed to UL924
standard and be approved for use in damp locations. When specified,
the Self-Powered model equipped with advanced diagnostic shall
self-test by simulating a power failure for one minute every 30 days,
30 minutes every 60 days and 90 minutes every 360 days. A diagnostic
circuit shall continuously monitor the performance of the battery,
charger module and LED lamps. Upon failure detection the system
shall display the error on the AC pilot lamp, which will change color
from green to red and will flash with a specific code. The red light
shall be steady-on in case of “Battery Disconnect”; it shall flash with
one blink for “Battery failure”, two blinks for “Charger failure” and
four blinks for “LED lamp failure”. A label with the diagnostic legend
• Slim-line canopy for top and end mounting
• Universal mounting or wall, end, or ceiling mounting
• Universal, field-selectable knock-out chevrons
• Long-life LED light source. Red LED’s of ALINGAP technology
• Dual voltage input: 120/347VAC 60Hz
• Low power consumption: less than 3.5W in any configuration
• Self-Powered
models with sealed maintenance-free Nickel-Cadmium
batteries
• Meets or exceeds CSA 22.2 No. 141 requirements
• Five-year full warranty
DIMENSIONS
Dimensions are approximate and subject to change.
85/8” [21.9 cm]
91/8” [23.1 cm]
51/2” [13.9 cm]
43/8” [11.1 cm]
127/8” [32.7 cm]
17/8” [4.7 cm]
shall be visible next to the pilot light.
The Exit Sign shall be Emergi-Lite® Model:
POWER CONSUMPTION
MODEL
AC SPECS
.
DC SPECS
AC only
120/347VAC
Less than 3W
-
-
AC/DC remote
120/347VAC
Less than 3W
6 to 48VDC
Less than 1.5W
Self-Powered
120/347VAC
Less than 3.5W
Nickel-Cadmium battery
Minimum 90 minutes
Self-Powered with diagnostic
120/347VAC
Less than 3W
Nickel-Cadmium battery
Minimum 90 minutes
ORDERING INFORMATION
ENCLOSURE
COLOUR
SERIES
PRED= LED die
cast
BA= black/ brushed
aluminum
A= brushed aluminum
WA= white/ brushed
aluminum
W= factory white
B= black
UNIT TYPE
VOLTAGE
LEGEND COLOUR
OPTIONS
AC= AC only
AC2C1= dual AC circuit (2 x 120V)
UD= 120/277 or 120/347VAC & 6 to 48VDC
IDN= Self-Powered diagnostic
Nickel-Cadmium (90 Min)
IN= Self-Powered Nickel-Cadmium
(90 Min)
NEX= NEXUS® system interface (90 Min)*
EXUS® wireless system
NEXRF= N
interface (90 Min)*
Blank= dual AC
circuit
only
2= 120/277VAC
3= 120/347VAC
R1= single face red
R2= double face red
G1= single face green
G2= double face green
-TP=tamper-proof screws
-VRTP= vandal resistant
shield with
tamper-proof
screws*
*Consult your sales representative for options
available with the NEXUS® system.
EXAMPLE: PREDAAC2R1
27
*Indicate single or double face
Project/Location:
Prestige™ LPEX100
Series
Contractor:
Date:
Die-Cast Aluminum Exit Sign
FEATURES
TYPICAL SPECIFICATIONS
•S
lim contoured body design with brushed aluminum faceplate
(single or double face option)
Supply and install the Emergi-Lite® LPEX100 Series LED Exit
Signs. The equipment shall operate with universal two-wire AC
input voltage from 120VAC to 347VAC at less than 3W and universal
two-wire DC input voltage from 6VDC to 48VDC at less than 1.5W
for single and double face signs. The faceplate(s) and the back plate
shall snap together and shall be made of Die-Cast aluminum. The
light source shall be light emitting diodes (LED). The LED lamps
shall provide illumination in normal and emergency operation and
shall be mounted inside the exit on a plastic frame/reflector. Red
LED technology shall be ALINGAP. An LED-sensitive diffuser shall
be mounted behind the legend to provide the 6” high by 3/4” stroke
letters with even illumination.
• Durable powder-coated Die-Cast construction
• Energy efficient - consumes less than 3W
• Universal mounting – wall, end or ceiling mounting
• Long-life, energy-efficient ALINGAP technology LED light source
reduces maintenance and energy costs
•D
iagnostic/self-test feature comes standard on all Self-Powered
models
•1
00% bright, even illumination in both normal and emergency
operation
The Self-Powered model shall stay illuminated during emergency
operation for at least 90 minutes (red) and at least 60 minutes (green)
upon AC failure. The Self-Powered model shall include self-testing
and self-diagnostic functions: the equipment shall automatically test
itself for 5 minutes every 30 days, 30 minutes every 60 days and 90
minutes annually. A “Service Required” lamp shall be located near
the test switch and flash in the case of a fault detection. A two-LED
diagnostic display shall be located inside the equipment and shall be
capable of identifying the source of failure that may occur (battery,
charger circuitry, or LED lamp failure).
• Maintenance-free, long-life sealed nickel cadmium battery
• Normal
AC and emergency DC operation – 120 to 347V universal
AC input; 6 to 48V universal DC input
• NEXUS® compatible (for more information on NEXUS®, please
consult your sales representative)
• CSA certified meets or exceeds CSA 22.2 No. 141 requirements
The Exit Sign shall be CSA-C860 approved and meets CSA 22.2 No.141
DIMENSIONS
The equipment shall be Emergi-Lite® Model:
Dimensions are approximate and subject to change.
460.0079-E
93/4” [24.8 cm]
87/8” [23 cm]
61/4” [16 cm]
13 ” [33 cm]
1/8
13/4” [4.3 cm]
ORDERING INFORMATION
LPEX= exit
102= single face,
universal mount
103= double face,
universal mount
HOUSING
FACEPLATES COLOURS
WW= factory white
BB= black
AA= brushed aluminum
CH= all chrome
PB= all polished brass
BZ= bronze
BA= black/brushed aluminum
WA= white/brushed aluminum
Other colours available.
Consult your sales representative.
Wall Mount
460.0027-E
End Mount
460.0028-E
Ceiling Mount
POWER CONSUMPTION
14” [35 cm]
FACEPLATES
.
WIRE GUARDS
45/8” [11.8 cm]
SERIES
Prepared by:
MODEL
AC SPECS
DC SPECS
AC/DC red
120/347VAC Less than 2W
6 to 48VDC
Less than 1.5W
AC/DC green
120/347VAC Less than 2W
6 to 48VDC
Less than 1.5W
SelfPowered red
Nickel-Cadmium
Min. 90 minutes
120/347VAC Less than 3W
battery
Self-Powered
green
120/347VAC Less than 3W
MODEL
Nickel-Cadmium
Min. 60 minutes
battery
OPTIONS
U= 120 to 347VAC, 6 to 48VDC
ID= 120 to 347VAC Self-Powered
c/w auto-diagnostics
NEX= NEXUS® wired system
interface*
-TP= tamper-proof screws
-VRTP= vandal resistant shield with
tamper-proof screws*
-G= green legend
990.0119-E= tamper-proof bit**
*Consult your sales representative for
options available with the NEXUS®
system.
* Indicate single or double face
**One bit needed per order.
EXAMPLE: LPEX102BAU-TP
28
Project/Location:
Prestige™ LPSR100
Series
Contractor:
Date:
Die-Cast Aluminum “Sortie” Sign
Prepared by:
FEATURES
TYPICAL SPECIFICATIONS
• Durable, powder-coated Die-Cast construction
Supply and install the Emergi-Lite® LPSR100 Series LED “SORTIE’’
Exit Signs. The equipment shall operate with universal two-wire AC
input voltage from 120VAC to 347VAC at less than 3W and universal
two-wire DC input voltage from 6VDC to 48VDC at less than 1.5W for
single or double face signs. The faceplate(s) and the back plate shall
snap together and shall be made of Die-Cast aluminum. The Exit Sign
shall have a maximum depth of 1-3/4’’.
• Slim
contoured body design with brushed aluminum faceplate
(single or double face option)
• Diagnostic/self-test
feature comes standard on all
Self-Powered units
• Universal mounting – wall, end or ceiling mounting
The light source shall be light emitting diodes (LEDs). The LED
lamps shall provide illumination in normal and emergency operation
and shall be mounted inside the exit. Red LED technology shall
be ALINGAP. A LED-sensitive diffuser shall be mounted behind
the legend to provide the 6” high by 3/4” stroke letters with even
illumination.
• 100%
bright, even illumination in both normal and emergency
operation
• Long-life, energy-efficient ALINGAP technology LED light source
reduces maintenance and energy costs
• Energy efficient – consumes less than 3W
• Maintenance-free, long-life sealed Nickel-Cadmium battery
The Self-Powered model shall stay illuminated during emergency
operation for at least 60 minutes upon AC failure. The Self-Powered
model shall include self-testing and self-diagnostic functions: the
equipment shall automatically test itself for 5 minutes every 30 days,
30 minutes every 60 days and 90 minutes annually. A “Service” pilot
light shall be located near the test switch and flash in the case of a
fault detection. A two-LED diagnostic display shall be located inside
the equipment and shall be capable of identifying the source of
failure (battery, charger circuitry, or LED lamp failure).
• Normal
AC and emergency DC operation – 120 to 347V universal
AC input; 6 to 48V universal DC input
• NEXUS® compatible (for more information on NEXUS®, please
consult your sales representative)
• CSA certified, meets or exceeds CSA 22.2 No. 141 requirements
The Exit Sign shall be CSA-C860 approved and meets CSA 22.2 No.141
The equipment shall be Emergi-Lite® Model:
.
WIRE GUARDS
DIMENSIONS
Dimensions are approximate and subject to change.
460.0057-E
Wall Mount
460.0048-E
End Mount
460.0058-E
Ceiling Mount
POWER CONSUMPTION
93/4” [24.8 cm]
87/8” [22.5 cm]
61/4” [15.7 cm]
45/8” [11.8 cm]
MODEL
AC SPECS
AC/DC
120/347VAC
Less
than 2W
Self-Powered
120/347VAC
Less
than 3W
13/4” [4.3 cm]
18 ” [46.4 cm]
1/4
DC SPECS
6 to 48VDC
Less than
1.5W
Nickel-Cadmium
battery
Min. 60
minutes
191/8” [48.7 cm]
ORDERING INFORMATION
SERIES
FACEPLATES*
LPSR= LED
sortie
102= single face
103= double face
HOUSING
FACEPLATES COLOURS
WW= white/white
BB= black/black
WA= white/brushed aluminum
BA= black /brushed aluminum
AA= brushed aluminum/brushed
aluminum
CH= chrome/chrome
SUPPLY AND VOLTAGE
OPTIONS
U= 120VAC to 347VAC, 6VDC to 48VDC
ID= 120VAC to 347VDC Self-Powered
including auto-diagnostics
NEX= NEXUS® wired system interface*
-TP= tamper-proof screws
-VRTP= vandal resistant shield with
tamper-proof screws*
990.0119-E= tamper-proof bit**
*Consult your sales representative for options
available with the NEXUS® system.
* Indicate single or double face
** One bit needed per order.
*Universal mounting
Other colours available.
EXAMPLE: LPSR102WWU-TP
29
Project/Location:
Contractor:
LPEX300 Series
Date:
Extruded Aluminum Exit Sign
Prepared by:
TYPICAL SPECIFICATIONS
FEATURES
• Thin profile, 2-piece extruded aluminum housing
Supply and install the Emergi-Lite® LPEX300 Series LED Exit Sign.
The equipment shall operate with universal AC input voltage of
120/277 347VAC at less than 1.5W and universal two-wire DC input
voltage from 6VDC to 24VDC at less than 1.5W for single and double
face signs. The Exit Sign shall consist of a two-piece white extruded
aluminum combined body/faceplate with a maximum depth of 1-1/4”.
The exit shall also include extruded aluminum end caps with white
gaskets in order to provide protection to the internal components
and eliminate any possible light leaks. The exit fixture shall be either
single or double-faced as shown on the drawings. The faceplate
shall be of a stencil design and will incorporate 6” high letters with
a 3/4” stroke. The canopy shall fasten to the exit body for ease of
installation in either ceiling or end mount. The fixture shall contain
a light source, which shall be LED with a long life and shall consist
of separate AC and DC LED sources in the case of AC/DC-remote
equipment. Red LED technology shall be ALINGAP.
• Pre-specified mounting
• Universal, field-selectable chevrons (knockout)
• Energy efficient – consumes less than 3.5W in AC or DC mode
• Long life ALINGAP technology energy-efficient LED light source
•C
SA certified, meets or exceeds CSA 22.2, No. 141 and C860
requirements
• Normal
AC and emergency DC operation –
120, 277 or 347V AC input; 6 to 24V DC input
• Available in single or double face
• Indirect refractive technology provides bright, even illumination
The Exit Sign in a Self-Powered configuration shall be equipped
with a Nickel-Cadmium battery and shall stay illuminated during
emergency operation for at least two hours upon AC failure.
The Exit Sign shall be CSA-C860 approved.
DIMENSIONS
The equipment shall be Emergi-Lite® Model:
.
Dimensions are approximate and subject to change.
WIRE GUARDS
123/8” [31.4 cm]
13/8” [3.4 cm]
ORDERING INFORMATION
LPEX30= LED EXIT
FACEPLATES
2= single face
3= double face
Wall Mount
460.0027-E
End Mount
460.0028-E
Ceiling Mount
MODEL
13” [33.2 cm]
SERIES
460.0079-E
POWER CONSUMPTION
95/8” [24.3 cm]
55/8” [14.2 cm]
87/8” [22.5 cm]
47/8” [12.5 cm]
COLOUR
MOUNTING
W= polar white
B= black
TA= textured
aluminum
BA= brushed
aluminum
-CM= ceiling mount
-EM= end mount
-WM= wall mount
AC SPECS
AC/DC
standard, red
120/277/347VAC
Less than
1.5W
6 to 48VDC
Less
than
1.5W
AC/ special
DC, red
120/277/347VAC
Less than
1.5W
36 or 48 or
120VDC
Less
than 3W
120VAC/DC two
wires, red
120VAC
Less than
3W
120VDC
Less
than 3W
Self-Powered
red
120/347VAC
Less than Nickel-Cadmium
3.5W
battery
VOLTAGE
-U= 120/277/347VAC, 6 to 24VDC
-U36= 120/277/347VAC-36VDC,
4 wires
-U48= 120/277/347VAC-48VDC,
4 wires
20/277/347VAC, 120VDC,
-U120= 1
4 wires
-8= 240VAC, no DC*
-I= 120/347VAC Self-Powered
-2I= 120/277VAC Self-Powered
20VAC-120VDC
-EM120-2W= 1
-2 wires
* Consult your sales representative for
availability and other DC voltages.
EXAMPLE: LPEX302W-CM-UTP
30
DC SPECS
Min. 2
hours
OPTIONS
-TP= tamper-proof screws
990.0119-E= tamper-proof
bit*
*One bit needed per order.
Project/Location:
Contractor:
Date:
LPSR300 Series
Prepared by:
Extruded Aluminum “Sortie” Sign
TYPICAL SPECIFICATIONS
FEATURES
• Thin
profile, two-piece extruded aluminum housing simply slides
together
Supply and install the Emergi-Lite® LPSR300 Series LED Exit Sign.
The equipment shall operate with universal AC input voltage of 120,
277 or 347VAC at less than 1.5W and universal two-wire DC input
voltage from 6VDC to 24VDC at less than 1.5W for single and double
face signs. The Exit Sign shall consist of a two-piece white extruded
aluminum combined body/faceplate with a maximum depth of 1-1/4”.
The exit shall also include extruded aluminum end caps with white
gaskets in order to provide protection to the internal components
and eliminate any possible light leaks. The exit fixture shall be either
single or double-faced as shown on the drawings. The faceplate shall
be of a stencil design and will incorporate 6” high letters with a 3/4”
stroke. The canopy shall fasten to the exit body for ease of
installation in either ceiling or end to wall mount.
• Mounting to be pre-specified
• Standard field-selectable directional knockout chevrons
• Indirect
refractive lighting technology provides bright, even
illumination
• Long life, energy-efficient ALINGAP LED light source
• Energy efficient: consumes less than 3.5W
• Normal
AC and emergency DC operation –
120/277/347VAC and 6V to 24VDC input
• CSA certified, meets or exceeds CSA 22.2 No. 141 requirements
The fixture shall contain a light source, which shall be LED with a
long life and shall consist of separate AC and DC LED sources in
the case of AC/DC-remote equipment. Red LED technology shall be
ALINGAP.
DIMENSIONS
The Exit Sign in a Self-Powered configuration shall be equipped
with a Nickel-Cadmium battery and shall stay illuminated during
emergency operation for at least two hours upon AC failure.
Dimensions are approximate and subject to change.
47/8” [12.5 cm]
The Exit Sign shall be CSA-C860 approved and meets CSA 22.2 No.141
460.0057-E
Wall Mount
460.0048-E
End Mount
460.0058-E
Ceiling Mount
POWER CONSUMPTION
13/8” [3.4 cm]
191/8” [48.6 cm]
.
WIRE GUARDS
95/8” [24.3 cm]
55/8” [14.2 cm]
87/8” [22.5 cm]
The equipment shall be Emergi-Lite® Model:
MODEL
19 ” [50.4 cm]
7/8
AC SPECS
DC SPECS
AC/DC
standard, red
120/277/347VAC
Less than
1.5W
6 to 48VDC
Less
than
1.5W
AC/ special
DC, red
120/277/347VAC
Less than
1.5W
36/48/120VDC
Less
than 3W
120VAC/DC
two wires, red
120VAC
Less than
3W
120VDC
Min. 3W
Self-Powered,
red
120/347VAC
Less than Nickel-Cadmium
3.5W
battery
Min. 2
hours
ORDERING INFORMATION
SERIES
FACEPLATES
LPSR30= SORTIE
2= single face
3= double face
COLOUR
W= polar white
B= black
TA= textured
aluminum
BA= brushed
aluminum
MOUNTING
-CM= ceiling mount
-EM= end mount
-WM= wall mount
SUPPLY VOLTAGE
-U= 120/277/347VAC, 6 to 24VDC
-U36= 120/277/347VAC, 36VDC
-U48= 120/277/347VAC, 48VDC
-U120= 120/277/347VAC, 120VDC
-I= 120/347VAC Self-Powered
20VAC - 120VDC
-EM120-2W= 1
- 2 wires
OPTIONS
-TP= tamper-proof screws
990.0119-E= tamper-proof
bit*
*One bit needed per order.
EXAMPLE: CS4000WHULTP
31
C8ES300 & C8SE300
Series
Bilingual Extruded Aluminum Sign
Contractor:
Date:
Prepared by:
TYPICAL SPECIFICATIONS
FEATURES
• Thin
profile, 2-piece extruded aluminum housing simply slides
together
Supply and install the Emergi-Lite® C8ES300 Series LED Exit Sign.
The equipment shall operate with universal AC input voltage of
120, 277 or 347VAC at less than 1.5W and universal two-wire DC
input voltage from 6VDC to 24VDC at less than 2.5W for single and
double face signs. The Exit Sign shall consist of a two-piece white
extruded aluminum combined body/faceplate with a maximum
depth of 1 1/4”. The exit shall also include extruded aluminum
end caps with white gaskets in order to provide protection to the
internal components and eliminate any possible light leaks. The
exit fixture shall be either single or double-faced as shown on the
drawings. The faceplate shall be of a stencil design and will have
6” high letters with a 3/4” stroke indicating both EXIT and SORTIE
side by side. The canopy shall fasten to the exit body for ease of
installation in either ceiling or wall mount. The fixture shall contain
a light source, which shall be LED with a long life and shall consist
of separate AC and DC LED sources in the case of AC/DC-remote
equipment. Red LED technology shall be ALINGAP.
• P re-specified mounting
• Universal, field-selectable chevrons (knockout)
• Energy efficient – consumes less than 7W in AC or DC mode
• Normal
AC and emergency DC operation
120, 277 or 347V AC input; 6 to 24V DC input
• Available in single or double face
• Custom wording available on request
• Indirect refractive technology provides bright, even illumination
• Long-life ALINGAP technology, energy-efficient LED light
source
• CSA certified, meets or exceeds CSA 22.2 No. 141 requirements
The Exit Sign in a Self-Powered configuration shall be equipped
with a Nickel-Cadmium battery and shall stay illuminated during
emergency operation for at least two hours upon AC failure.
POWER CONSUMPTION
MODEL
Project/Location:
The Exit Sign shall be CSA-C860 approved and meets CSA 22.2 No.141
AC SPECS
The equipment shall be Emergi-Lite® Model:
DC SPECS
AC/DC standard,
red
120/347VAC
Less
than 2W
6 to 48VDC
Less
than 3W
AC/ special DC,
red
120/277/347VAC
Less
than 2W
36 or 48 or
120VDC
Less
than 6W
120VAC/DC two
wires, red
120VAC
Less
than 6W
120VDC
Less
than 6W
Self-Powered,
red
120 or 347VAC
Less
than 7W
Nickel-Cadmium
battery
Min. 2
hours
.
WIRE GUARDS
460.0059-E
Wall Mount
460.0092-E
Ceiling Mount
DIMENSIONS
Dimensions are approximate and subject to change.
55/8” [14.2 cm]
55/8” [14.2 cm]
303/8” [77.1 cm]
95/8” [24.3 cm]
87/8” [22.5 cm]
47/8” [12.5 cm]
13/8” [3.4 cm]
303/8” [77.1 cm]
ORDERING INFORMATION
SERIES
FACES
C8ES30= exit sortie
C8SE30= sortie exit
2= single face
3= double face
COLOUR
W= polar white
B= black
TA= t extured
aluminum
BA= brushed
aluminum
MOUNTING
-CM= ceiling mount
-WM= wall mount
EXEMPLE: C8ES302W-CM-UTP
32
VOLTAGE
-U= 120/277/347VAC, 6 to 24VDC
-U36= 120/277/347VAC-36VDC
-U48= 120/277/347/VAC-48VDC
-U120= 120/277/347/VAC-120VDC
-I= 120VAC, Self-Powered
-3I= 347VAC, Self-Powered
20VAC-120VDC-2
-EM120-2W= 1
wires
OPTIONS
-TP= tamper-proof screws
990.0119-E= tamper-proof bit*
*One bit needed per order.
Project/Location:
Contractor:
EA Series
Date:
Extruded Aluminum Pictogram Sign
Prepared by:
FEATURES
TYPICAL SPECIFICATIONS
• Durable extruded, one-piece aluminum housing and face plates
• White LED light source
Supply and install the Emergi-Lite® EA Series pictogram Exit
Signs. The equipment shall operate with universal 2-wire AC input
voltage of 120 to 347VAC at less than 2.5W and universal 2-wire
DC input voltage from 6 to 24VDC at less than 1.5W for single and
double face signs. The equipment shall be suitable for wall, end, or
ceiling mount. The housing shall be constructed of rugged extruded
aluminum and have a maximum depth of 2-1/2”. The faceplate(s)
shall be constructed of extruded aluminum and shall incorporate
a protective clear polycarbonate panel. Each face plate shall come
standard with two legend films for pictogram and direction selection.
The light source shall be white light-emitting diodes (LED) and shall
provide even illumination in normal and emergency operation. The
pictogram Exit Sign in a Self-Powered configuration shall use a
sealed Nickel-Cadmium battery of 2.4V nominal voltage and shall
stay illuminated during emergency operation for at least two hours
upon AC failure.
The pictogram Exit Sign shall meet CSA 22.2 No.141-10.
• Supplied standard with two pictogram films per face, for direction
selection
• Meets or exceeds CSA 22.2 No.141-10 standard for pictogram exit
signs
• Universal AC input: two-wire 120 to 347VAC; standard DC input:
two-wire 6 to 24VDC
• Energy efficient – consumes less than 2.5W in AC or DC-remote
mode
• Self-Powered model gives standard two hours of back-up lighting
• Universal mounting – end, wall or ceiling
• Easy access to wiring entry for all mounting options
• Comes standard with the Emergi-Lite® EZ2 canopy for quick and
easy installation
The equipment shall be Emergi-Lite® Model:
.
WIRE GUARDS
460.0079-E
DIMENSIONS
Wall mount
460.0027-E
End mount
460.0028-E
Ceiling mount
Dimensions are approximate and subject to change.
PICTOGRAM
STRAIGHT FROM HERE
73/4” [19.7 cm]
63/8” [16.2 cm]
< PICTOGRAM
LEFT FROM HERE
83/4” [22.3 cm]
43/4” [11.9 cm]
131/8” [33.3 cm]
PICTOGRAM >
RIGHT FROM HERE
21/2” [6.3 cm]
141/8” [35.9 cm]
POWER CONSUMPTION
MODEL
AC SPECS
DC SPECS
AC-only
120 to 347VAC
Less than 2.5W
-
-
AC/DC standard
120 to 347VAC
Less than 2.5W
6 to 24VDC
Less than 1.5W
Less than 2.5W
AC/Special DC
120 to 347VAC
Less than 2.5W
36, 48, 120VDC
Two-wire 120V AC/DC
120VAC
Less than 2.5W
120VDC
Less than 2.5W
Self-Powered
120 to 347VAC
Less than 3W
Nickel-Cadmium battery
Minimum two hours
ORDERING INFORMATION
SERIES
EA= pictogram
Exit Sign
FACES / MOUNTING
1= single face
universal mount
2= double face
universal mount
3= single/double face
universal mounting
COLOURS
W= factory white
B= black
G= grey
BA= brushed
aluminum
Other colours available
VOLTAGE
U= 120 to 347VAC;
6 to 24VDC
I= 120 to 347VAC;
Self-Powered/2 hours
U00= 120 to 347VAC only
U36= 120 to 347VAC; 36VDC
U48= 120 to 347VAC; 48VDC
U120= 120 to 347VAC;120VDC
2120= 2-wires 120VAC/VDC
EXAMPLE: EA1WUTP
33
OPTIONS
IDN= Self-Powered diagnostics,
non audible
EXUS® system interface
NEX= N
(90 Min)*
NEXRF= NEXUS® wireless system
interface (90 Min)*
-TP= tamper-proof screws
-VR= v andal-resistant
shield and tamperproof screws
990.0119-E= tamper-proof
bit*
*Consult your sales representative for
options available with the NEXUS® system.
*One bit per order. Sold
separately.
Project/Location:
LPEX50 Series
Contractor:
Date:
Extruded Aluminum
Exit Sign
Prepared by:
FEATURES
TYPICAL SPECIFICATIONS
• Long-life, energy-efficient ALINGAP technology red LED light
source completely enclosed in acrylic module
Supply and install the Emergi-Lite® LPEX50 Series LED Exit Signs.
The equipment shall operate with universal AC input voltage of
120VAC, 277VAC or 347VAC at less than 1.5W and universal two-wire
DC input voltage from 6VDC to 24VDC at less than 1.5W for single or
double face signs.
• Durable, extruded, one-piece aluminum housing
• Single
illumination module lights both single and double face exit
signs
The housing shall be constructed of rugged extruded aluminum and
have a maximum depth of 2-1/2”. The faceplate(s) shall be constructed of extruded aluminum and come standard with knockout
chevrons.
• Highly
energy efficient – consumes less than 2.5W in AC or DC
mode
• Normal
AC and emergency DC operation –
120/277/347V AC input; 6 to 24V DC input
The light source shall be light emitting diodes (LED). The LED lamps
shall provide illumination in normal and emergency operation and
shall be mounted inside the exit housing, not on the face. The red
LED technology shall be ALINGAP. An LED-sensitive diffuser shall
be mounted behind the legend to provide the 6” high by 3/4” stroke
letters with even illumination. The Exit Sign in a Self-Powered
configuration shall stay illuminated during emergency operation for
at least 90 minutes upon AC failure.
• Comes with the Emergi-Lite® EZ2 canopy for quick and
easy installation
• Also available with power pack; see LPEX50-P catalogue sheet
• CSA certified, meets or exceeds CSA 22.2 No. 141 requirements
DIMENSIONS
The Exit Sign shall be CSA-C860 approved and meets CSA 22.2 No.141
Dimensions are approximate and subject to change.
The equipment shall be Emergi-Lite® Model:
.
73/4” [19.7 cm]
83/4” [22.3 cm]
43/4” [11.9 cm]
WIRE GUARDS
460.0079-E
131/8” [33.3 cm]
21/2” [6.3 cm]
141/8” [35.9 cm]
Wall Mount
460.0027-E
End Mount
460.0028-E
Ceiling Mount
POWER CONSUMPTION
MODEL
AC SPECS
DC SPECS
AC/ standard DC, red
120/277/347VAC
Less than 1.5W
6 to 24VDC
Less than 1.5W
AC/ special DC, red
120/277/347VAC
Less than 1.5W
36 or 48 or 120VDC
Less than 2.5W
Minimum 90 minutes
Self-Powered, red
120 to 347VAC
Less than 3W
Nickel-Cadmium battery
AC/ standard DC, green
120 to 347VAC
Less than 1.5W
6 to 24VDC
Less than 1.5W
Self-Powered, green
120 to 347VAC
Less than 3W
Nickel-Cadmium battery
Minimum 90 minutes
ORDERING INFORMATION
SERIES
FACES
COLOUR
LPEX5= LED EXIT
2= single face,
universal
mount
3= double face,
universal
mount
W= factory white
B= black
BA= brushed aluminum
TA= textured aluminum
W= polar white
MOUNTING
-U= 120/277/347VAC, 6 to 24VDC
-EM120-2W= 120VAC, 120VDC 2 wires
-U36= 120/277/347VAC - 36VDC
-U48= 120/277/347VAC - 48VDC
-U120= 120/277/347VAC - 120VDC
-I= 120 to 347VAC Self-Powered
OPTIONS
-TP= tamper-proof screws
-VRSTP= vandal resistant shield with
tamper-proof screws*
-G= green legend
990.0119-E= tamper-proof bit**
*Indicate single or double face.
**One bit needed per order.
EXAMPLE: LPEX52W-U-VRTP
34
Project/Location:
Contractor:
C8SR50 Series
Date:
Extruded Aluminum “Sortie” Sign
Prepared by:
FEATURES
TYPICAL SPECIFICATIONS
• Long life ALINGAP technology LED light source is completely
enclosed in acrylic module
Supply and install the Emergi-Lite® C8SR50 Series LED “SORTIE’’
Exit Signs. The equipment shall operate with universal two-wire AC
input voltage of 120VAC to 347VAC at less than 1.5W and universal
two-wire DC input voltage from 6VDC to 24VDC at less than 1.5W for
single or double face signs.
• Durable, extruded, one-piece aluminum housing
• Single
illumination module lights both single and double face exit
signs
The housing shall be constructed of rugged extruded aluminum and
have a maximum depth of 2-1/2”. The faceplate(s) shall be constructed of extruded aluminum and come standard with knockout
chevrons.
• Highly energy efficient, consumes a maximum of 3W
•N
ormal AC and emergency DC operation – 120V to 347VAC; 6V to
24VDC input
• Also available with power pack; see C8SR50-P catalogue sheet
The light source shall be light emitting diodes (LED). The LED lamps
shall provide illumination in normal and emergency operation and
shall be mounted inside the exit housing, not on the face. The red
LED technology shall be ALINGAP. An LED-sensitive diffuser shall
be mounted behind the legend to provide the 6” high by 3/4” stroke
letters with even illumination. The Exit Sign in a Self-Powered
configuration shall stay illuminated during emergency operation for
at least 60 minutes upon AC failure.
• CSA certified, meets or exceeds CSA 22.2 No. 141 requirements
• Includes Emergi-Lite® EZ2 mounting bracket included, for quick
and easy installation
DIMENSIONS
Dimensions are approximate and subject to change.
The Exit Sign shall be CSA-C860 approved.
The equipment shall be Emergi-Lite® Model:
.
4 ” [11.9 cm]
83/4” [22.3cm]
73/4” [19.7 cm]
63/8” [16.2 cm]
3/4
183/4” [47.5 cm]
WIRE GUARDS
460.0057-E
21/2” [6.3 cm]
193/4” [50.1 cm]
Wall Mount
460.0048-E
End Mount
460.0058-E
Ceiling Mount
POWER CONSUMPTION
MODEL
AC SPECS
DC SPECS
AC/ standard DC, red
120 to 347VAC
Less than 1.5W
6 to 24VDC
Less than 1.5W
AC/ special DC, red
120/277/347VAC
Less than 1.5W
36 or 48 or 120VDC
Less than 3W
Self-Powered, red
120 to 347VAC
Less than 3W
Nickel-Cadmium battery
Min. 60 or 120 minutes
ORDERING INFORMATION
SERIES
C8SR5=
aluminum
SORTIE
FACEPLATE & MOUNTING
2= single face/universal
mounting
3= double face/universal
mounting
COLOUR
W= factory white
B= black
TA= textured
aluminum
W= polar white
BA= brushed
aluminum
VOLTAGE
-U= 120/277/347VAC 6 to 24VDC
20VAC, 120VDC 2
-EM120-2W= 1
wires
-U36= 120/277/347VAC - 36VDC
-U48= 120/277/347VAC - 48VDC
-U120= 120/277/347VAC - 120VDC
-I= 120/347VAC Self-Powered
OPTIONS
-TP= tamper-proof screws
-VRTP=vandal resistant shield with
tamper-proof screws*
-G= green legend
990.0119-E= tamper-proof bit**
*Indicate single or double face.
**One bit needed per order.
EXAMPLE: CS5100WH-UL
35
Project/Location:
LPEX Series
Contractor:
Date:
Triangular Extruded
Aluminum Exit Sign
FEATURES
TYPICAL SPECIFICATIONS
• Rugged extruded aluminum housing
Supply and install the Emergi-Lite® LPEX Series of three-face LED
Exit Signs. The equipment shall operate with universal AC input
voltage of 120, 277 or 347VAC at less than 2W and universal two-wire
DC input voltage from 6VDC to 24VDC at less than 3.5W. The housing
shall be constructed of rugged extruded aluminum painted with a
factory white finish and shall have three face plates oriented
symmetrically at 120 degrees in the horizontal plan.
• Extruded aluminum faceplates
• White finish standard
• Standard field-selectable knockout chevrons
• Long life, energy-efficient LED light source
• ALINGAP technology LED
The faceplates shall be constructed of extruded aluminum and come
standard with knockout chevrons. The light source shall be red light
emitting diodes (LED) of long-life technology ALINGAP. An
LED-sensitive diffuser shall be mounted behind the legend to provide
the 6” high by ¾” stroke letters with even illumination. Each legend
shall be illuminated by one dedicated LED lamp (strip). The LED
lamps shall be oriented two downwards and one upwards and shall
provide illumination in normal and emergency operation. Eventual
failure of one LED lamp shall not affect the well-functioning of the
other two lamps. The Exit Sign shall come standard with a pendant
kit with a 3/8” diameter pipe for ceiling-mount installation.
• CSA certified, meets or exceeds CSA 22.2 No. 141 requirements
DIMENSIONS
Dimensions are approximate and subject to change.
1/8
13
The Exit Sign shall be C860 approved and meets CSA 22.2 No.141
The equipment shall be Emergi-Lite® Model:
117/8”[30.1cm]
]
cm
3.3
”[3
13 1/8
”[3
3.3
cm
]
Prepared by:
.
73/4”[19.7cm]
131/8”[33.3cm]
135/8”[34.7cm]
POWER CONSUMPTION AND UNIT RATING
MODEL
AC SPECS
AC / DC - standard
120/277/347VAC
DC SPECS
Less than 2W
6 to 24VDC
Less than 3.5W
ORDERING INFORMATION
SERIES
LPEX= exit extruded
aluminum
FACES/ MOUNTING
55= 2 sided face (Wall mounting only)
56= 3 sided face
(Pendant mounting only)
COLOUR
W= factory white
VOLTAGE
-U= 1
20/277/347VAC,
6 to 24VDC
OPTIONS
-TP= tamper-proof screws
990.0119-E= tamper-proof
bit*
*One bit per order.
EXAMPLE: LPEX55W-U
36
Project/Location:
Contractor:
LPEX54 Series
Date:
Recessed Exit Sign
Prepared by:
TYPICAL SPECIFICATIONS
FEATURES
• Extruded aluminum faceplate with overlapping trim is standard
Supply and install the Emergi-Lite® LPEX54 Series Exit Sign.
The LPEX54 exit shall be recessed mount. The equipment shall
operate with universal AC input voltage of 120, 277 or 347VAC at less
than 1.5W and universal two wire DC input voltage from 6VDC to
24VDC at less than 1.5W. The face shall be constructed of extruded
aluminum and have an overlapping trim allowing for installation
in any location. The faceplate shall come standard with knockout
chevrons. The recessed back box shall be of rugged steel construction. The light source shall be light emitting diodes (LED). Red LED
technology shall be ALINGAP. The LED lamps shall provide illumination in normal and emergency operation and shall be mounted inside
the exit housing, not on the face. An LED sensitive diffuser shall
be mounted behind the legend to provide the 6” high by 3/4” stroke
letters with even illumination.
• Universal, field-selectable chevrons (knockout)
• Long-life, energy-efficient ALINGAP LED light source
• Indirect refractive technology provides bright, even illumination
• Normal
AC and emergency DC operation –
120 to 347V universal AC input;
6 to 24V two-wire DC input
• Energy efficient – consumes less than 3.5W in AC or DC mode
•N
ickel-Cadmium battery provides at least 90 minutes of
emergency operation in DC mode
• CSA certified, meets or exceeds CSA 22.2 No. 141 requirements
The Exit Sign in a Self-Powered configuration shall be equipped
with a Nickel-Cadmium battery and shall stay illuminated during
emergency operation for at least 90 minutes upon AC failure.
DIMENSIONS
Dimensions are approximate and subject to change.
21/2” [6.5 cm]
The Exit Sign shall be CSA-C860 approved and meets CSA 22.2 No.141
21/4” [5.7 cm]
The equipment shall be Emergi-Lite® Model:
.
71/2” [19 cm]
87/8” [22.7 cm]
123/4” [32.4 cm]
WIRE GUARDS
460.0091-E
143/4” [37.5 cm]
Wall Mount
POWER CONSUMPTION
MODEL
AC SPECS
DC SPECS
AC/ standard DC, red
120/277/347VAC
Less than 1.5W
6 to 24VDC
Less than 1.5W
AC/ special DC, red
120/277/347VAC
Less than 3W
36 or 48 or 120VDC
Less than 2.5W
Nickel-Cadmium
battery
Minimum 90 minutes
Self-Powered, red
120 to 347VAC
Less than 3W
AC/ standard DC, green
120 to 347VAC
Less than 1.5W
6 to 24VDC
Less than 1.5W
Less than 3.5W
Nickel-Cadmium
battery
Minimum 90 minutes
Self-Powered, green
120 to 347VAC
ORDERING INFORMATION
SERIES
LPEX54= LED
aluminum
recessed
EXIT
COLOUR
W= factory white
B= black
BA= brushed aluminum
TA= textured aluminum
VOLTAGE
-U= 120/277/347VAC, 6 to 24VDC
-EM120-2W= 120VAC, 120VDC 2 wires
-U36= 120/277/347VAC - 36VDC
-U48= 120/277/347VAC - 48VDC
-U120= 120/277/347VAC - 120VDC
-I= 120 to 347VAC Self-Powered
OPTIONS
-TP= tamper-proof screws*
-VRTP= vandal resistant shield and tamper-proof screws*
-G= green legend
990.0119-E= tamper-proof bit**
*Indicate single or double face.
**One bit needed per order.
EXAMPLE: LPEX54B-U-VRTP
37
C8ES70 & C8SE70
Series
Project/Location:
Contractor:
Date:
Bilingual Extruded Aluminum
Exit Sign
FEATURES
TYPICAL SPECIFICATIONS
• Durable, extruded, one-piece aluminum housing
Supply and install the Emergi-Lite® bilingual C8ES70 or C8SE70
Series LED Exit Sign. The equipment shall operate with universal
AC input voltage of 120 to 347VAC at less than 2W and universal
two-wire DC input voltage from 6VDC to 24VDC at less than 3.5W for
single and double face signs. The housing shall be constructed of
rugged extruded aluminum and have a maximum depth of 2-1/2”.
The faceplate(s) shall be constructed of extruded aluminum and
come standard with knockout chevrons. The equipment shall have
three (3) canopies that shall fasten for installation in either ceilingor wall-mount applications. The light source shall be light emitting
diodes (LED).
• Long-life, energy-efficient ALINGAP technology red LED light
source completely enclosed in acrylic module
• Single
illumination module lights both single and double face Exit
Signs
• Highly
energy efficient, consumes a maximum of 5.5W in AC or DC
mode (standard model)
•N
ormal AC and emergency DC operation – 120V to 347VAC and 6V
to 24VDC input
• CSA certified, meets or exceeds CSA 22.2 No. 141 requirements
The LED lamps shall provide illumination in normal and emergency
operation and shall be mounted inside the exit housing, not on
the face. Red LED technology shall be ALINGAP An LED-sensitive
diffuser shall be mounted behind the legend to provide the 6” high by
3/4” stroke letters with even illumination.
DIMENSIONS
Dimensions are approximate and subject to change.
The Exit Sign in a Self-Powered configuration shall be equipped
with a Nickel-Cadmium battery and shall stay illuminated during
emergency operation for at least 60 minutes upon AC failure.
83/4” [22.3 cm]
73/4” [19.7 cm]
73/4” [19.7 cm]
43/4” [11.9 cm]
The Exit Sign shall be CSA-C860 approved and meets CSA 22.2 No. 141
The equipment shall be Emergi-Lite® Model:
.
21/2” [6.3 cm]
73/4” [19.7 cm]
29” [73.3 cm]
Prepared by:
WIRE GUARDS
29” [73.3 cm]
460.0059-E
Wall Mount
460.0092-E
Ceiling Mount
POWER CONSUMPTION
MODEL
AC SPECS
DC SPECS
AC/ standard DC, red
120 to 347VAC
Less than 3W
6 to 24VDC
Less than 3.5W
AC/ special DC, red
120/277/347VAC
Less than 5.5W
36 or 48 or 120VDC
Less than 5.5W
Self-Powered, red
120/347VAC
Less than 6W
Nickel-Cadmium battery
Min. 60 or 120 minutes
ORDERING INFORMATION
LIGHT SOURCE
C8= LED
LETTERING
FACE
ES= exit sortie 6”
letters
SE= sortie exit 6”
letters
72= single
face
73= double
face
COLOUR
POWER SOURCE AND VOLTAGE
W= factory white
BA= brushed
aluminum
TA= textured
aluminum
B= black
-U= 120 to 347VAC, 6 to 24VDC
-EM120-2W= 120VAC, 120VDC 2 wires
-U36= 120/277/347VAC - 36VDC
-U48= 120/277/347VAC - 48VDC
-U120= 120/277/347VAC - 120VDC
-I= 120 to 347VAC Self-Powered
OPTIONS
-TP= tamper-proof screws
-VRTP= vandal resistant shield with
tamper-proof screws*
-90= 90 minutes duration
(Self-Powered only)
-120= 120 minutes duration
(Self-Powered only)
990.0119-E= tamper-proof bit**
-3C= 3 canopies
*Indicate single or double face
**One bit needed per order.
EXAMPLE: C8ES72W-U-TP
38
Project/Location:
ES70B12 &
SE70B12 Series
Contractor:
Date:
Prepared by:
Bilingual Extruded Aluminum Sign
TYPICAL SPECIFICATIONS
FEATURES
• Durable, extruded, one-piece aluminum housing
Supply and install the Emergi-Lite® bilingual ES70B12 & SE70B12
Series LED Exit Sign.
• Long-life, energy-efficient ALINGAP technology red LED light
source completely enclosed in acrylic module
The equipment shall operate with universal AC input voltage from
120 to 347VAC at less than 3W and universal two-wire DC input
voltage from 6VDC to 24VDC at less than 3W for single and double
face signs. The housing shall be constructed of rugged extruded
aluminum and have a maximum depth of 2-1/2”. The faceplate(s)
shall be constructed of aluminum and come standard with knockout
chevrons. The equipment shall have one (1) canopy that shall fasten
for installation in either ceiling- or wall-mount applications.
• Double LED module lights both single and double face Exit Signs
• Highly
energy efficient, consumes a maximum of 3W in AC or DC
mode (standard model)
•N
ormal AC and emergency DC operation – 120/277/347VAC and
6V to 24VDC input
• CSA certified, meets or exceeds CSA 22.2 No. 141 requirements
The light source shall be light emitting diodes (LED). The LED lamps
shall provide illumination in normal and emergency operation and
shall be mounted inside the exit housing, not on the face. Red LED
technology shall be ALINGAP. An LED-sensitive diffuser shall be
mounted behind the legend to provide the 6” high by 3/4” stroke
letters with even illumination.
POWER CONSUMPTION
MODEL
AC SPECS
AC/ standard DC,
red
120 to
347VAC
DC SPECS
Less than
3W
6 to
24VDC
The Exit Sign shall be CSA-C860 approved and meets CSA 22.2 No.141
Less than
3W
The equipment shall be Emergi-Lite® Model:
.
DIMENSIONS
Dimensions are approximate and subject to change.
63/8” [16.2 cm]
43/4” [11.9 cm]
63/8” [16.2 cm]
151/4” [38.9 cm]
21/2” [6.3 cm]
151/4” [38.9 cm]
151/4” [38.9 cm]
21/2” [6.3 cm]
151/4” [38.9 cm]
171/4” [43.8 cm]
21/4” [5.7 cm]
151/4” [38.9 cm]
137/8” [35.1 cm]
151/4” [38.9 cm]
RECESSED MOUNT
SE70B12 SERIES
15” [38 cm]
137/8” [35.4 cm]
ES70B12 SERIES
171/4” [43.8 cm]
ORDERING INFORMATION
SERIES
ES= exit sortie
SE= sortie exit
FACES
72= single
face
73= double
face
APPROVAL
B12
COLOUR
W= factory white
B= black
TA= textured
aluminum
POWER SOURCE AND VOLTAGE
-U= 120 to 347VAC, 6 to 24VDC
-EM120-2W= 120VAC, 120VDC 2 wires
-U36= 120/277/347VAC - 36VDC
-U48= 120/277/347VAC - 48VDC
-U120= 120/277/347VAC - 120VDC
-I= 120 to 347VAC Self-Powered
Other colours available.
Consult your sales
representative.
OPTIONS
-TP= tamper-proof screws*
-VRTP= vandal resistant shield with
tamper-proof screws*
-R= recessed mount**
990.0119-E= tamper-proof bit*
*One bit needed per order.
** Not available in Self-Powered
EXAMPLE: ES72B12W-U
39
Project/Location:
EAC Series
Contractor:
Date:
Extruded Aluminum
Combination Unit
Prepared by:
TYPICAL SPECIFICATIONS
FEATURES
• Solid extruded aluminum construction, painted factory white
Supply and install the Emergi-Lite® EAC Series combination
emergency light battery unit and the pictogram Exit Sign. The unit
shall be suitable for universal mounting: wall, end, or ceiling. The
unit shall include a power pack made of steel and a legend housing
including a one-piece extruded aluminum frame. The legend
housing shall have a maximum depth of 2-1/2”. The face plate(s)
shall be of extruded aluminum and shall incorporate a protective
clear polycarbonate panel. Each face plate shall come standard with
two legend films for pictogram and direction selection. The light
source shall be white light-emitting diodes (LED) and shall provide
even illumination in normal and emergency operation. The power
pack shall be complete unit equipment with battery charger and
rechargeable battery. The battery shall be maintenance-free, sealed
Lead-Calcium. In case of AC power failure the equipment shall
provide minimum 30 minutes of emergency lighting. The rated DC
power available for emergency lights shall be 27W or up to 80W, as
specified. The emergency heads shall require no tools to adjust and
aim. The heads shall be made of durable thermoplastic construction
as otherwise specified.
• Universal mounting: end, wall or ceiling
• Meets
or exceeds CSA 22.2 No.141-10 standard for unit equipment
and pictogram safety signs
• Legend illuminated by long-life white LED’s
• Comes
standard with two pictogram films per face, for direction
selection
• 5W
LED emergency lights provide 70’ of egress illumination on a
6-foot wide path
• Sealed, maintenance-free Lead-Calcium battery
• Remote
load capacity: 70’ up to 350’ of egress illumination when
using LED remote heads
Units with “auto-diagnostic option” shall include a micro-controller
circuit to monitor all the critical functions of the equipment and
execute periodical tests of one minute every 30 days, 10 minutes
every 6 months and 30 minutes every 12 months. In case of
equipment malfunction, an LED-based diagnostic display shall
generate a service alarm and indicate the cause of failure: battery,
charger circuit, emergency lamps or exit sign lamps.
The equipment shall meet or exceed the requirements of CSA 22.2
No.141-10 standard.
The equipment shall be Emergi-Lite® Model:
.
WIRE GUARDS
40
460.0081-E
Wall mount
460.0060-E
Ceiling mount
Project/Location:
EAC Series
Contractor:
Date:
Extruded Aluminum
Combination Unit
Prepared by:
DIMENSIONS
11/8” [2.8 cm]
Dimensions are approximate and subject to change.
45/8” [11.7 cm]
123/4” [32.4 cm]
PICTOGRAM
STRAIGHT FROM HERE
71/2” [19.0 cm]
121/8” [30.8 cm]
< PICTOGRAM
LEFT FROM HERE
PICTOGRAM >
RIGHT FROM HERE
61/2” [16.5 cm]
131/8” [33.3 cm]
141/2” [36.7 cm]
POWER CONSUMPTION
MODEL
Pictogram Module
EMERGENCY POWER AVAILABLE FOR LAMPS
AC SPECS
120/347VAC
Less than 1.5W
EAC-627
EAC-640
120/347VAC
0.15/0.05 A
EAC-672
EAC-1250
EAC-1280
120/347VAC
0.25/0.09 A
30MIN
1H00
1H30
2H00
4H00
-
-
-
-
-
27
16
11
9
-
40
23
16
13
-
72
42
30
24
12
50
29
21
16
8
80
46
32
27
13
ORDERING INFORMATION
SERIES
FACES /
MOUNTING
EAC= pictogram
aluminum
combination
unit
1= single face
2= double face
universal
mounting
COLOUR
W= factory
white
B= black
POWER EM.
LIGHTS
627= 6V-27W
640= 6V-40W
672= 6V-72W
1250= 12V-50W
1280= 12V-80W
HEADS
o
Blank= n
heads
1= one head
2= two heads
HEAD STYLE AND WATTAGE
Blank= no heads
LA= MR16 LED, 6V-4W
LG= MR16 LED,
12V-4W
LI= MR16 LED, 12V-5W
LJ= MR16 LED,12V-6W
M18= mini tungsten,
12V-18W, wedge
base
M= mini tungsten,
12V-9W, wedge
base
MQ= mini halogen,
12V-8W, quartz
bi-pin
MQ12= mini halogen,
12V-12W,
quartz bi-pin
MI= MR16 halogen,
6V-6W
MJ= MR16 halogen,
6V-10W
MK= MR16 halogen,
12V-12W
MA= MR16 halogen,
12V-20W
MB= MR16, 12V-35W
MR= MR16, 12V-35W,
high output
41
-TP= tamper-proof screws***
-2= 120/277/VAC input
D3= time delay (15 minutes)**
U= auto-diagnostics *
UN= auto-diagnostics,
non-audible*
NEX= NEXUS® system
interface****
NEXRF= wireless NEXUS®
system interface****
* Not available with 6V-72W
** Time delay only with
auto-diagnostics
*** Bit ordered separately:
990.0119-E
*MB & MR are using EF150
type heads.
EXAMPLE: EAC1W6272LAD­3
OPTIONS
**** Consult your sales
representative for options
available with the NEXUS®
system.
Project/Location:
LPEX50-P Series
Contractor:
Date:
Extruded Aluminum
Combination Unit - 6/12V
FEATURES
Prepared by:
TYPICAL SPECIFICATIONS
Exit Sign
• Extruded aluminum faceplate
Supply and install the Emergi-Lite® LPEX50-P LED Exit Sign and
power pack combination series. The exit housing shall be constructed
of rugged extruded aluminum. The faceplate shall be constructed of
extruded aluminum. The Exit Sign shall have a maximum depth of
2-1/2”. The faceplate(s) shall come standard with knockout chevrons.
The light source shall be light emitting diodes (LED). The LED lamps
shall provide illumination in normal and emergency operation and
shall be mounted inside the exit housing, not on the face. An
LED-sensitive diffuser shall be mounted behind the legend to provide
the 6” high by 3/4” stroke letters with even illumination. The power
pack shall be a completely self-contained emergency unit with its own
charger and rechargeable battery. The housing shall be made of steel,
painted factory white. The unit shall be designed to furnish exit
illumination from the normal AC source. When a power failure
occurs the mounted heads along with the Exit Sign are illuminated
in emergency mode for a minimum of 30 minutes. The power pack is
furnished with a test switch and high charge pilot light and is available
as either 18, 36 or 72W. The heads shall require no tools to adjust and
aim. The heads will be constructed of a durable thermoplastic construction and use 6V, 9W lamps or as otherwise specified.
• Universal, field-selectable chevrons (knockout)
• ALINGAP LED technology
Power Pack
• Completely self-contained unit with rechargeable sealed lead
battery
• Lamp heads require no tools to adjust or aim
• Meets or exceeds CSA 22.2 No. 141 requirements
•DIMENSIONS
Dimensions are approximate and subject to change.
45/8” [11.7 cm]
121/4” [31.1 cm]
121/8” [30.8 cm]
The Exit Sign shall be CSA-C860 approved and meets CSA 22.2 No. 141.
The equipment shall be Emergi-Lite® Model:
71/2”
[19.0 cm]
61/2” [16.5 cm]
.
WIRE GUARDS
131/8” [33.3 cm]
460.0081-E
Wall Mount
460.0060-E
Ceiling Mount
141/2” [36.7 cm]
POWER CONSUMPTION AND UNIT RATING
MODEL
WATTAGE CAPACITY
AC SPECS
1H30
2H00
Exit Sign Module
Less than 1.5W
-
-
-
-
-
LPX5-P1
LPX5-P3
LPX5-P3A
0.15/0.05 A
0.15/0.05 A
0.18/0.07 A
18
36
72
10
21
42
7
15
30
6
12
24
3
6
12
LPX5-P7
0.18/0.07 A
36
21
15
12
6
LPX5-P7A
0.15/0.05 A
72
42
30
24
12
120/347VAC
30MIN
1H00
4H00
ORDERING INFORMATION
SERIES
COLOUR
VOLTAGE
POWERPACK
LPEX52=
single
face
LPEX53=
double
face
W= f actory
white
B= black
BA=
brushed
aluminum*
TA=
textured
aluminum*
Blank=
120/347VAC
-2= 277VAC
-P1= 6V-18W
-P3= 6V-36W
-P3A= 12V-36W
-P7= 6V-72W
-P7A= 12V-72W
*Black heads
OPTIONS
Blank= no options
-G= green legend
D= time delay
U= auto-diagnostics
X2= remote test receiver*
TX2= remote test transmitter***
NEX= NEXUS® system interface**
NEXRF= wireless NEXUS® system interface**
*Remote test transmitter needed.
**Consult your sales representative for options
***One per order
EXAMPLE: LPEX52W-P3/2MQ12
42
NUMBER OF
HEADS
/0= no heads
/1= one head
/2= two heads
HEAD STYLE AND
WATTAGE
LA= MR16 LED, 6V-4W
LG= MR16 LED, 12V-4W
LI= MR16 LED, 12V-5W
LJ= MR16 LED, 12V-6W
M= mini tungsten, 12V-9W,
wedge base
MQ= mini halogen, 12V-8W,
quartz bi-pin
MQ12= mini halogen, 12V-12W,
quartz bi-pin
MI= MR16 halogen, 6V-6W
MJ= MR16 halogen, 6V-10W
MK= MR16 halogen, 12V-12W
MA= MR16 halogen, 12V-20W
Other styles available.
Consult your sales representative.
Project/Location:
C8SR50-P Series
Contractor:
Date:
Extruded Aluminum
Combination Unit - 6/12V
Prepared by:
FEATURES
TYPICAL SPECIFICATIONS
• Extruded aluminum faceplate
Supply and install the Emergi-Lite® C8SR50-P LED “SORTIE’’ Exit
Sign with power pack combination series. The exit housing and the
faceplate(s) shall be constructed of rugged extruded aluminum. The
Exit Sign shall have a maximum depth of 2-1/2”. The faceplate(s)
shall come standard with knockout chevrons.
•R
ugged extruded aluminum housing with a maximum depth of
2-1/2”
• White finish standard
• Standard field-selectable knockout chevrons
The light source shall be light emitting diodes (LED). Red LED
technology shall be ALINGAP. The LED lamps shall provide
illumination in normal and emergency operation and shall be
mounted inside the exit housing, not on the face. An LED-sensitive
diffuser shall be mounted behind the legend to provide the 6” high
by 3/4” stroke letters with even illumination. The power pack shall
be a completely self-contained emergency unit with its own charger
and rechargeable battery. The housing shall be made of steel. The
unit shall be designed to furnish exit illumination from the normal
AC source. When a power failure occurs, the mounted heads
along with the Exit Sign are illuminated in emergency mode for a
minimum of 30 minutes. The power pack is furnished with a test
switch and high charge pilot light and is available as either 18, 36 or
72W. The heads shall require no tools to adjust and aim. The heads
will be constructed of polycarbonate and include 6V, 9W lamps or as
otherwise specified.
• Long
life, energy-efficient LED light source, mounted inside the exit
housing, not on the faceplate.
• ALINGAP technology LED
• NEXUS® compatible (for more information on NEXUS®, please
consult your sales representative)
• Completely
self-contained unit with rechargeable sealed lead-acid
battery
• Lamp heads require no tools to adjust or aim
• Provides
a minimum of 30 minutes of illumination (lamp heads and
exit sign) in emergency mode
• CSA certified, meets or exceeds CSA 22.2 No. 141. requirements
DIMENSIONS
The Exit Sign shall be CSA-C860 approved and meets CSA 22.2 No.141.
45/8”
[11.7 cm]
The equipment shall be Emergi-Lite® Model:
121/4” [31.1 cm]
.
12 ” [30.8 cm]
WIRE GUARDS
71/2” [19.0 cm]
1/8
11/8” [2.8 cm]
Dimensions are approximate and subject to change.
61/2” [16.5 cm]
460.0081-E
Wall Mount
460.0060-E
Ceiling Mount
183/4” [47.5 cm]
201/8” [51.0 cm]
POWER CONSUMPTION AND UNIT RATING
MODEL
WATTAGE CAPACITY
AC SPECS
1H30
2H00
Sortie Sign Module
Less than 2W
-
-
-
-
-
C8SR5= 6V-18W
C8SR5= 6V-36W
C8SR5= 12V-36W
C8SR5= 6V-72W
C8SR5= 12V-72W
0.15/0.05 A
0.15/0.05 A
0.18/0.07 A
0.18/0.07 A
0.15/0.05 A
18
36
72
36
72
10
21
42
21
42
7
15
30
15
30
6
12
24
12
24
3
6
12
6
12
120/347VAC
30MIN
1H00
4H00
ORDERING INFORMATION
SERIES
HOUSING
COLOUR
C8SR52=
single
face
C8SR53=
double
face
W= factory white
B= black
BA= brushed
aluminum*
TA= textured
aluminum*
*Black heads
VOLTAGE
Blank=
120/347VAC
-2= 277VAC
SUPPLY AND
VOLTAGE
-P1= 6V-18W
-P3= 6V-36W
-P3A= 12V-36W
-P7= 6V-72W
-P7A= 12V-72W
OPTIONS
Blank= no options
D= time delay
U= auto-diagnostics
X2= remote test receiver*
TX2= remote test transmitter***
NEX= NEXUS® system interface**
ireless NEXUS® system
NEXRF= w
interface**
*Transmitter test required by command.
** Consult your sales representative for
options
*** One per order
EXAMPLE: C8SR52W-P1D/0M
43
#OF
HEADS
/0= no
heads
ne
/1= o
head
/2= two
heads
MODEL AND POWER HEADLIGHTS
LA= MR16 LED, 6V-4W
LG= MR16 LED, 12V-4W
LI= MR16 LED, 12V-5W
LJ= MR16 LED, 12V-6W
M= mini tungsten, 12V-9W, wedge base
MQ= mini halogen, 12V-8W, quartz bi-pin
MQ12= mini halogen, 12V-12W, quartz bi-pin
MI= MR16 halogen, 6V-6W
MJ= MR16 halogen, 6V-10W
MK= MR16 halogen, 12V-12W
MA= MR16 halogen, 12V-20W
Other models available.
Contact your sales representative.
Project/Location:
Contractor:
ES Series
Date:
All Metal Pictogram Sign
Prepared by:
FEATURES
TYPICAL SPECIFICATIONS
• Metal construction using Canadian cold-rolled steel
•B
ased on a modular design, this product comes pre-assembled
for quick, easy installation
• Long-life white LED light source
• Supplied
standard with two pictogram films per face, for
direction selection
•M
eets or exceeds CSA 22.2 No.141-10 standard for pictogram
exit signs
• Two-wire
universal AC input: 120 to 347VAC; two-wire standard
DC input: 6 to 24VDC
• Energy
efficient – consumes less than 2.5W in AC mode and only
1W in DC-remote
• Self-Powered
model delivers standard two hours of back-up
lighting
• Universal mounting – end, wall or ceiling
Supply and install the Emergi-Lite® ES Series pictogram Exit Signs.
The equipment shall operate with universal 2-wire AC input voltage of
120 to 347VAC at less than 2.5W and universal 2-wire DC input voltage
from 6 to 24VDC at 1W consumption for single and double face signs.
The sign shall be suitable for wall, end, or ceiling mount. The frame
and back plate shall each be of one-piece steel construction. The
faceplate(s) shall be constructed of robust clear polycarbonate panels
with an opaque border coloured factory-white. Each face plate shall
come standard with two legend films for pictogram and directional
indicators. The light source shall be white light-emitting diodes (LED)
and shall provide even illumination in normal and emergency operation.
The pictogram Exit Sign in a Self-Powered configuration shall use a
sealed Nickel-Cadmium battery of 2.4V nominal voltage and shall stay
illuminated during emergency operation for at least two hours upon AC
failure.
The Exit Sign shall be listed CSA 22.2 No.141-10.
The equipment shall be Emergi-Lite® Model:
• Easy access to wiring entry for all mounting options
• Canopy
mounting system designed specifically for ease of
installation
DIMENSIONS
WIRE GUARDS
460.0079-E
End mount
460.0028-E
Ceiling mount
MODEL
PICTOGRAM
STRAIGHT FROM HERE
PICTOGRAM >
RIGHT FROM HERE
75/8” [19.2 cm]
121/8” [30.7 cm]
133/8” [33.9 cm]
87/8” [22.4 cm]
45/8” [11.7 cm]
73/8” [18.7 cm]
Wall mount
460.0027-E
POWER CONSUMPTION
Dimensions are approximate and subject to change.
< PICTOGRAM
LEFT FROM HERE
.
AC SPECS
DC SPECS
AC-only
120 to
347VAC
Less than
2.5W
-
-
AC/DC
standard
120 to
347VAC
Less than
2.5W
6 to 24VDC
Less than
1W
AC/Special DC
120 to
347VAC
Less than
2.5W
36, 48, 120VDC
Less than
2.5W
Two-wire 120V
AC/DC
120VAC
Less than
2.5W
120VDC
Less than
2.5W
Self-Powered
120 to
347VAC
Less than
2.5W
Nickel-Cadmium
Min. 2 hours
battery
21/8” [5.3 cm]
ORDERING INFORMATION
SERIES
ES= steel pictogram
Exit Sign
FACES / MOUNTING
1= single face
universal mounting
2= double face
universal mounting
3= single/double face
universal mounting
VOLTAGE
COLOUR
U= 120 to 347VAC; 6 to 24VDC
I= 120 to 347VAC; Self-Powered/2 hours
U00= 120 to 347VAC only
U36= 120 to 347VAC; 36VDC
U48= 120 to 347VAC; 48VDC
U120= 120 to 347VAC; 120VDC
2120= 2-wires 120VAC/VDC
W= factory white
B= black
G= grey
-TP= tamper-proof screws**
-VRSTP= vandal-resistant shield and
tamper-proof screws**
990.0119-E= tamper-proof bit*
Other colours
available.
*One bit per order. Sold separately.
** Not available on universal faces.
EXAMPLE: ES1UWVR
44
OPTIONS
Project/Location:
Contractor:
EX10 Series
Date:
Prepared by:
All Metal Exit Sign
FEATURES
TYPICAL SPECIFICATIONS
• Two-wire universal AC input
Supply and install the Emergi-Lite® EX10 Series Exit Signs. The
equipment shall operate with universal 2-wire AC input voltage
of 120 to 347VAC at less than 1.5W and universal 2-wire DC input
voltage from 6 to 24VDC at less than 1.5W for single and double face
signs. The sign shall be suitable for wall, end, or ceiling mount. The
faceplates shall be constructed of steel and shall come standard
with knockout chevrons. The frame shall be of one-piece steel
construction.
• Pre-assembled for quick, easy installation
• Universal mounting – end, wall or ceiling
• Supplied
with two stencil plates, red diffusing lenses and
backplate
• Easy access to wiring entry for all mounting options
• Canopy
mounting system designed specifically for ease of
installation
The light source shall be light-emitting diodes (LED). The LED lamps
shall provide illumination in normal and emergency operation and
shall be mounted inside the exit housing, not on the face. Red LEDs
shall be of ALINGAP technology.
• Universal, field-selectable chevrons (knockout)
• Energy efficient – consumes less than 3W in AC or DC mode
• Normal
AC and emergency DC operation – 120 to 347V AC input;
6 to 24V DC input
An LED-sensitive diffuser shall be mounted behind the legend to
provide the 6” high by 3/4” stroke letters with even illumination.
• Long life energy-efficient ALINGAP technology LED light source
• Also available with power pack; see EX10-P catalogue sheet
The Exit Sign in a Self-Powered configuration shall stay illuminated
during emergency operation for at least 90 minutes upon AC failure.
• CSA certified, meets or exceeds CSA 22.2 No. 141. requirements
The Exit Sign shall be CSA-C860 approved and meets CSA 22.2 No.141.
The equipment shall be Emergi-Lite® Model:
POWER CONSUMPTION
DIMENSIONS
Dimensions are approximate and subject to change.
MODEL
AC SPECS
73/8” [18.7 cm]
75/8” [19.2 cm]
87/8” [22.4 cm]
45/8” [11.7 cm]
12 ” [30.7 cm]
2 ” [5.3 cm]
1/8
1/8
133/8” [33.9 cm]
WIRE GUARDS
460.0079-E
DC SPECS
AC-only, red
120 to 347VAC
Less than
1.5W
-
-
AC/DC
standard, red
120 to 347VAC
Less than
1.5W
6 to 24VDC
Less than
1.5W
AC/special DC,
Less than
120/277/ 347VAC
red
3W
36 or 48 or
120VDC
Less than
2.5W
Self-Powered
red
120 to 347VAC
Less than Nickel-Cadmium
3W
battery
Min. 60
minutes
AC-only, green
120 to 347VAC
Less than
1.5W
-
-
AC/DC
standard, green
120 to 347VAC
Less than
1.5W
6 to 24VDC
Less than
2.5W
Self-Powered
green
120 to 347VAC
Less than Nickel-Cadmium
3W
battery
Min. 90
minutes
Wall Mount
460.0027-E
End Mount
460.0028-E
Ceiling Mount
ORDERING INFORMATION
SERIES
EX10= LED EXIT sign / Universal
mount
COLOUR
POWER SOURCE AND VOLTAGE
OPTIONS
W= factory white
B= black
TA= textured aluminum
-U= universal voltage 120 to 347VAC
6 to 24VDC
-U00= 120 to 347VAC, no DC**
-U36= 120/277/347VAC - 36VDC*
-U48= 120/277/347VAC, 48VDC*
-U120= 120/347VAC, 120VDC*
-EM120-2W= 120VAC, 120VDC 2 wires*
-I= Self-Powered 120 to 347VAC
-TP= tamper-proof screws
-VRTP= vandal resistant shield with tamper-proof
screws**
-G= green legend
990.0119-E= tamper-proof bit*
Other colours available,
please contact your sales
representative.
*For green legend, consult your sales representative.
** Supply as single face
*One bit per order.
EXAMPLE: EX10W-U
45
**Indicate single or double face
Project/Location:
Contractor:
C8SR10 Series
Date:
All Metal “Sortie” Sign
Prepared by:
FEATURES
TYPICAL SPECIFICATIONS
• Metal legend panel with red letter panel
Supply and install the Emergi-Lite® C8SR10 Series LED “SORTIE’’ Exit
Signs. The equipment shall operate with universal two-wire AC input
voltage of 120VAC to 347VAC at less than 1.5W and universal two-wire
DC input voltage from 6VDC to 24VDC at less than 1.5W for single or
double face signs.
•M
etal construction using Canadian cold-rolled steel with baked
enamel finish – will not yellow
• Universal mounting – end, wall or ceiling
• Easy access to wiring entry for all mounting options
The sign shall be suitable for wall, end or ceiling mount. The faceplates
shall be constructed of steel and shall come standard with knockout
chevrons. The frame shall be of a one-piece steel construction.
• Canopy
mounting system designed specifically for ease of
installation
• Standard field-selectable directional knockout chevrons
The light source shall be light emitting diodes (LED). The LED lamps
shall provide illumination in normal and emergency operation and
shall be mounted inside the exit housing, not on the face.
• Long life, energy efficient ALINGAP technology light source
• Energy efficient – consumes less than 3W
• Normal
AC and emergency DC operation – 120V to 347VAC and
6V to 24VDC input
• CSA certified, meets or exceeds CSA 22.2 No. 141. requirements
• Metal construction using Canadian cold-rolled steel
• Long-life, energy-efficient ALINGAP technology LED light
source completely enclosed in acrylic module
Red LED technology shall be ALINGAP. An LED-sensitive diffuser shall
be mounted behind the legend to provide the 6” high by 3/4” stroke
letters with even illumination.
The Exit Sign in a Self-Powered configuration shall stay illuminated
during emergency operation for at least 60 minutes upon AC failure.
The Exit Sign shall be CSA-C860 approved and meets CSA 22.2 No. 141.
The equipment shall be Emergi-Lite® Model:
• Also available with power pack; see SR catalogue sheet
WIRE GUARDS
DIMENSIONS
Dimensions are approximate and subject to change.
460.0057-E
Wall Mount
460.0048-E
End Mount
460.0058-E
Ceiling Mount
71/2” [19.1 cm]
83/4” [22.3 cm]
45/8” [11.7 cm]
71/2” [19.1 cm]
.
18” [45.7 cm]
21/8” [5.3 cm]
191/8” [48.5 cm]
POWER CONSUMPTION AND UNIT RATING
MODEL
AC SPECS
DC SPECS
AC/DC standard, red
120 to 347VAC
Less than 1.5W
6 to 24VDC
Less than 1.5W
AC/special DC, red
120/277/347VAC
Less than 2.5W
36 or 48 or 120VDC
Less than 2.5W
Self-Powered red
120 to 347VAC
Less than 3W
Nickel-Cadmium battery
Minimum 60 minutes
ORDERING INFORMATION
SERIES
C8SR10= universal mounting LED
SORTIE
COLOUR
W= factory white
B= black
TG= textured grey
SUPPLY AND VOLTAGE
-U= 120/347VAC, 6/12/24VDC
-I= Self-Powered 120/347VAC
20VAC, 120VDC
-EM120-2W= 1
2 wires
-U36= 120/277/347VAC, 36VDC
-U48= 120/277/347VAC, 48VDC
-U120= 120/347VAC, 120VDC
Other colours available.
Consult your sales
representative.
OPTIONS
-TP= tamper-proof screws
-VRTP= vandal resistant shield with tamper-proof
screws**
990.0119-E= tamper-proof bit*
*One bit needed per order.
** Indicate single or double face
EXAMPLE: C8SR10W-U-TP
46
Project/Location:
C8ES10 & C8SE10
Series
Contractor:
Date:
Prepared by:
Bilingual Steel Sign
TYPICAL SPECIFICATIONS
FEATURES
• Single
illumination module lights both single and double face Exit
Signs
Supply and install the Emergi-Lite® bilingual C8ES10 or C8SE10
Series LED Exit Sign. The equipment shall operate with universal AC
input voltage of 120 to 347VAC at less than 3W and universal two-wire
DC input voltage from 6VDC to 24VDC at less than 3.5W for single
and double face signs. The frame shall be of one-piece steel
construction and have a maximum depth of 2-1/8”. The faceplate(s)
shall be steel and come standard with knockout chevrons. The
equipment shall have two (2) canopies that shall fasten for
installation in ceiling-mount applications. The light source shall be
light emitting diodes (LED). The LED lamps shall provide illumination
in normal and emergency operation and shall be mounted inside the
exit housing, not on the face. Red LED technology shall be ALINGAP.
An LED-sensitive diffuser shall be mounted behind the legend to
provide the 6” high by 3/4” stroke letters with even illumination.
• Highly
energy efficient – consumes a maximum of 5.5W in AC or
DC mode
•N
ormal AC and emergency DC operation –
120 to 347V AC input; 6 to 24V DC input
• Meets or exceeds CSA 22.2 No. 141 requirements.
DIMENSIONS
Dimensions are approximate and subject to change.
73/8” [19 cm]
C8ES10 SERIES
The Exit Sign in a Self-Powered configuration shall stay illuminated
during emergency operation for at least
minutes upon AC
failure.
The Exit Sign shall be CSA-C860 approved and meets CSA 22.2 No.141.
C8SE10 SERIES
The equipment shall be Emergi-Lite® Model:
285/8” [73 cm]
4 ” [12 cm]
83/4” [22 cm]
71/2” [19 cm]
.
WIRE GUARDS
73/8” [19 cm]
5/8
460.0059-E
Wall Mount
460.0092-E
Ceiling Mount
285/8” [73 cm]
21/8” [5 cm]
POWER CONSUMPTION AND UNIT RATING
MODEL
AC SPECS
DC SPECS
AC/DC standard, red
120 to 347VAC
Less than 3W
6 to 24VDC
Less than 3.5W
AC/special DC, red
120/277/347VAC
Less than 5W
36 or 48 or 120VDC
Less than 5W
Self-Powered red
120 to 347VAC
Less than 6W
Nickel-Cadmium Battery
Min. 60 or 120 minutes
ORDERING INFORMATION
SERIES
C8= LED C860
approved
LETTERING
ES= EXIT SORTIE
6” letters
SE= SORTIE EXIT
6” letters
FACES
12= single face
13= double face
COLOUR
W= factory white
B= black
TG= textured grey
POWER SOURCE AND VOLTAGE
-U= 120 to 347VAC, 6 to 24 VDC
-EM120-2M=120VAC, 120VDC, 2 wires
-U36= 120/277/347VAC - 36VDC
-U48= 120/277/347VAC - 48VDC
-U120= 120/277/347VAC - 120VDC
-I= 120 to 347VAC, Self-Powered,
(60 minutes)
-I2= 120 to 347VAC Self-Powered,
(120 minutes )
OPTIONS
Blank= 2 canopies supplied
-TP= tamper-proof screws
-VRTP= vandal resistant
shield with
tamper- proof
screws**
-3C= 3 canopies
990.0119-E= tamper-proof
bit*
*One bit needed per order.
** Indicate single or double face
EXAMPLE: C8ES12W-U-VRTP
47
Project/Location:
Contractor:
ESC Series
Date:
Steel Combination Unit
Prepared by:
TYPICAL SPECIFICATION
FEATURES
• Universal mounting: end, wall or ceiling
Supply and install Emergi-Lite® ESC Series combination emergency
light battery unit and pictogram Exit Sign. The unit shall be made of
solid steel sheet metal and be suitable for universal mounting: wall,
end, or ceiling. The legend housing shall have a maximum depth of
2-1/8”. The legend face plate(s) shall be constructed of robust clear
polycarbonate panel(s) with an opaque border coloured factorywhite. Each face plate shall come standard with two legend films for
pictogram and direction selection. The light source shall be white
light-emitting diodes (LED) and shall provide even illumination in
normal and emergency operation. The power pack shall include one
circuit board with test switch and pilot light for battery charger and
legend LED driver. The unit shall include one 6V or 12V, maintenancefree, sealed Lead-Calcium battery and shall provide minimum 30
minutes of emergency lighting upon AC power failure. The electrical
power available for emergency lights shall be 28W or up to 72W, for 6V
and 50W or up to 80W for 12V, as specified. The emergency heads shall
require no tools to adjust and aim. The equipment shall meet or exceed
the requirements of CSA 22.2 No.141-10 standard.
• Meets
or exceeds CSA 22.2 No.141-10 standard for unit
equipment and pictogram Exit Signs
• Legend illuminated by long-life white LED’s
• Comes
standard with two pictogram films, for direction
selection
• Sealed, maintenance-free, 6V or 12V Lead-Calcium battery
• Remote
load capacity: 80W up to 560’ of egress illumination
when using LED remote heads
DIMENSIONS
Dimensions are approximate and subject to change.
PICTO
STRAIGHT FROM HERE
4 ” [11.7cm]
5/8
12 ” [32.0cm]
61/2” [16.5cm]
71/2” [19.1cm]
121/8” [30.8cm]
133/8” [34.0cm]
6V-44W &
6V-72W units
12V-50W &
12V-80W units
The equipment shall be Emergi-Lite® Model:
45/8” [11.7cm]
11” [28.0cm]
133/4” [34.8cm]
121/2” [31.7cm]
131/2” [34.2cm]
121/4” [31.0cm]
45/8” [11.7cm]
PICTO >
RIGHT FROM HERE
5/8
.
WIRE GUARDS
121/4” [31.2cm]
< PICTO
LEFT FROM HERE
460.0081-E
Wall mount
460.0060-E
Ceiling mount
6” [15.1cm]
6V-28W units
®
POWER CONSUMPTION
MODEL
EMERGENCY POWER AVAILABLE FOR LAMPS
30MIN
1H00
1H30
2H00
4H00
AC SPECS
Pictogram Module
ESC28
ESC44
ESC72
ESC-1250
ESC-1280
Less than 1.5W
120/347VAC
28
44
72
50
80
0.13 / 0.05 A
0.25 / 0.09 A
16
26
42
29
46
12
18
30
21
32
9
15
24
16
27
7
12
8
13
ORDERING INFORMATION
POWER EM.
LIGHTS
SERIES
ESC= pictogram
steel combo
exit sign
28= 6V-28W
44= 6V-44W
72= 6V-72W*
1250= 12V-50W*
1280= 12V-80W*
*Not available with
NEX & NEXRF
HOUSING
COLOUR
W= factory
white
B= black
HEADS
Blank= n
o
heads
1= one head
2= two heads
HEAD STYLE AND WATTAGE
Blank= no heads
LA= MR16 LED, 6V-4W
LG= MR16 LED, 12V-4W
LI= MR16 LED, 12V-5W
LJ= MR16 LED, 12V-6W
M= mini tungsten, 12V-9W, wedge base
MQ= mini halogen, 12V-8W, quartz bi-pin
MQ12= mini halogen, 12V-12W, quartz bi-pin
MI= MR16 halogen, 6V-6W
MJ= MR 16 halogen, 6V-10W
MK= MR16 halogen, 12V-12W
MA= MR16 halogen, 12V-20W
MB= MR16 halogen, 12V-35W*
MR= MR16 high-output, 12V-35W*
*MB & MR are using EL150 type heads
EXAMPLE: ESC28W2LA
48
OPTIONS
-TP= tamper-proof screws*
-2= 120/277VAC input
DF= double face sign
D3= time delay (15 minutes)
NEX= NEXUS® system interface**
NEXRF= wireless NEXUS® system
interface**
U= auto-diagnostics***
UN= auto-diagnostics,
non audible***
* Bit ordered separately: 990.0119-E
** Max. 44W; consult your sales
representative
*** U & UN available for 12V units only
Project/Location:
EX10-P & LPEX10-P
Series
Contractor:
Date:
Prepared by:
Metal Combination Unit
TYPICAL SPECIFICATIONS
FEATURES
ual input voltages 120/347VAC
D
Comes pre-assembled for quick, easy installation
Universal mounting – end, wall or ceiling
Easy access to wiring entry for all mounting options
Canopy mounting system designed specifically for ease of
installation
• Universal fields-selectable chevrons (knock out)
• Energy efficient – complete unit consumes less than 5W
Supply and install the Emergi-Lite® EX10-P & LPEX10-P Series LED
Exit Sign and power pack combination series. The exit housing and
faceplates shall be constructed of steel. The Exit Sign shall have a
maximum depth of 2-1/2”. The faceplate(s) shall come standard with
knockout chevrons. The light source for the Exit Sign shall be
light-emitting diodes (LED). The LED lamps shall provide
illumination in normal and emergency operation and shall be
mounted inside the exit housing, not on the face. Red LEDs shall be
of ALINGAP technology. An LED sensitive diffuser shall be mounted
behind the legend to provide the 6” high by 3/4” stroke letters with
even illumination. The power pack shall be a completely selfcontained emergency unit with its own charger and rechargeable
battery. The housing shall be made of steel. The power pack shall
include a test switch and high charge pilot light. The equipment
shall be designed to furnish exit illumination from the normal AC
source. When a power failure occurs the Exit Sign along with the
emergency heads shall illuminate for a minimum of 30 minutes. The
power available for emergency lights shall be 28W or as otherwise
specified.The heads shall require no tools to adjust and aim. The
heads will be of a durable thermoplastic construction and use 6V, 9W
and 12V, 9W lamps or as otherwise specified. The Exit Sign shall be
CSA-C860 approved and meets CSA 22.2 No. 141.
The equipment shall be Emergi-Lite® Model:
.
•
•
•
•
•
• CSA certified, meets or exceeds CSA 22.2 No. 141 requirements
• Long
life, energy-efficient LED light source, mounted inside the
exit housing, not on the faceplate
DIMENSIONS
Dimensions are approximate and subject to change.
45/8” [11.7 cm]
61/2” [16.6 cm]
121/8” [30.8 cm]
133/8” [34 cm]
121/4”
[31.2 cm]
11”
[28 cm]
73/8” [18.7 cm]
131/2” [34.2 cm]
133/4” [34.8cm]
121/2” [31.7cm]
71/2” [19.1cm]
12V-36W &
12V-72W units
125/8”
[32.0 cm]
121/4” [31 cm]
45/8” [11.7 cm]
45/8” [11.7cm]
EXTRA FACEPLATES
6”
[15.1 cm]
44W & 72W Units
005406-E
Standard Unit 28W
005407-E
WIRE GUARDS
460.0060-E
460.0081-E
005408-E
Ceiling Mount
Wall Mount
Factory white faceplate
+ red diffuser
Black faceplate + red
diffuser
Silver grey faceplate +
red diffuser
005409-E
005410-E
005411-E
Factory white faceplate
+ green diffuser
Black faceplate +
green diffuser
Silver grey faceplate +
green diffuser
POWER CONSUMPTION AND UNIT RATING
MODEL
WATTAGE CAPACITY
AC SPECS
1H30
2H00
4H00
Exit Sign Module
Less than 1.5W
-
-
-
-
-
EX10-P
EX10-P4
EX10-P7
LPEX10-P3A
LPEX10-P7A
0.15/0.05 A
0.15/0.05 A
0.15/0.05 A
less than 5W
less than 5W
28
44
72
76
72
16
26
42
21
42
12
18
30
15
30
9
15
24
12
24
7
12
6
12
120/347VAC
30MIN
1H00
ORDERING INFORMATION
SERIES
COLOUR
VOLTAGE
POWERPACK
OPTIONS
EX10=
6V
W= factory
white
B= black
G= grey*
Blank=
120/347VAC
-2=
120/277VAC
-P= 6V-28W
-P4= 6V-44W
-P7= 6V-72W
P3A = 12V-36W
P7A = 12V-72W
Blank= no options
-TP= tamper-proof screws
-G= green legend
D= time delay
U= auto-diagnostic, audible***
UN= auto-diagnostic, non-audible***
990.0119-E= tamper-proof bit*
NEX= NEXUS® system interface**
NEXRF= wireless NEXUS® system interface**
LPEX10=
12V
*Black
heads
* One bit per order.
**Consult your sales representative for options
available with the NEXUS® system.
***Only available in 12V units.
EXAMPLE: EX10W-P3/2MQ12
49
# OF
HEADS
/0= n
o
head
ne
/1= o
head
/2= t wo
heads
HEAD STYLE AND WATTAGE
LA= MR16 LED, 6V-4W
LG= MR16 LED, 12V-4W
LI= MR16 LED, 12V-5W
LJ= MR16 LED, 12V-6W
M= mini tungsten, 12V-9W, wedge base
MQ= mini halogen, 12V-8W, quartz bi-pin
MQ12= mini halogen, 12V-12W, quartz bi-pin
MI= MR16 halogen, 6V-6W
MJ= MR16 halogen, 6V-10W
MK= MR16 halogen, 12V-12W
MA= MR16 halogen, 12V-20W
Other styles available.
Consult your sales representative
Project/Location:
Contractor:
SR Series
Date:
All Metal “Sortie” Combination Unit
Prepared by:
FEATURES
TYPICAL SPECIFICATIONS
• Pre-assembled for ease of installation
• Metal housing with baked enamel finish – will not yellow
Supply and install the Emergi-Lite® SR Series LED “SORTIE’’ Exit
Sign with power pack series. The exit housing and the faceplate(s)
shall be constructed of steel. The Exit Sign shall have a maximum
depth of 2-1/2”. The faceplate(s) shall come standard with knockout
chevrons.
• Easy access to wiring entry
• Exit Sign with long life, ALINGAP LED light source
• Energy efficient, consumes less than 3W in stand-by mode
The light source shall be light emitting diodes (LED). Red LED
technology shall be ALINGAP. The LED lamps shall provide
illumination in normal and emergency operation and shall be
mounted inside the exit housing, not on the face. An LED-sensitive
diffuser shall be mounted behind the legend to provide the 6” high by
3/4” stroke letters with even illumination.
•P
ower pack comes standard with premium Lead-Calcium battery
•O
ther colours and options are available upon request
•C
SA certified, meets or exceeds CSA 22.2 No. 141 requirements
The power pack shall be a completely self-contained emergency unit
with its own charger and rechargeable battery. The housing shall be
made of steel. The unit shall be designed to furnish exit
illumination from the normal AC source. When a power failure
occurs, the mounted heads along with the Exit Sign are illuminated in
emergency mode for a minimum of 30 minutes. The power pack shall
be furnished with a test switch and high charge pilot light.
The heads shall require no tools to adjust and aim. The heads will
be constructed of durable thermoplastic and use 6V, 9W lamps or as
otherwise specified.
The Exit Sign shall be CSA-C860 approved and meets CSA 22.2 No.141.
The equipment shall be Emergi-Lite® Model:
WIRE GUARDS
50
460.0078-E
Wall Mount
460.0060-E
Ceiling Mount
Project/Location:
Contractor:
SR Series
Date:
All Metal “Sortie” Combination Unit
Prepared by:
DIMENSIONS
Dimensions are approximate and subject to change.
45/8” [11.7 cm]
45/8” [11.7 cm]
18” [45.7 cm]
61/2” [16.6 cm]
121/4” [31.2 cm]
11” [28.0 cm]
73/8” [18.7 cm]
121/4” [31.0 cm]
133/8” [34.1 cm]
191/8” [48.5 cm]
63/8” [16.2 cm]
POWER CONSUMPTION AND UNIT RATING
MODEL
WATTAGE CAPACITY
AC SPECS
30MIN
1H00
1H30
2H00
Sortie Sign Module
Less than 2W
-
-
-
-
4H00
-
R27= 6V-27W
0.25/0.08 A
27
15
12
9
-
0.25/0.08 A
50
30
20
16
8
12R50= 12V-50W
0.25/0.08 A
50
30
20
16
8
12R80= 12V-80W
0.25/0.08 A
80
45
36
27
12
R50= 6V-50W
120/347VAC
ORDERING INFORMATION
SERIES
COLOUR
VOLTAGE
SR12= s ingle
face, wall
or ceiling
mount
niversal
SR10= u
steel
mount
canopy
with two
faceplates
W= factory white
B= black
TG= textured grey*
Blank=
120/347VAC
* Black heads
VOLTAGE
AND SUPPLY
-P= 6V-27W
-P5= 6V-50W
-P5A= 12V-50W
-P8A= 12V-80W
OPTIONS
Blank= no options
-TP= tamper-proof screws
D1= time delay (5 minutes)
D2= time delay (10 minutes)
D3= time delay (15 minutes)
990.0119-E= tamper-proof
bit*
*One bit per proof
EXAMPLE: SR12W-P/0M
51
# OF
HEADS
MODEL AND POWER
HEADLIGHTS
/0= no
heads
/1= one
head
/2= two
heads
LA= MR16 LED, 6V-4W
LG= MR16 LED, 12V-4W
LI= MR16 LED, 12V-5W
LJ= MR16 LED, 12V-6W
M= mini tungsten, 12V-9W, wedge
base
MQ= mini halogen, 12V-8W, quartz
bi-pin
MQ12= mini halogen, 12V-12W, quartz
bi-pin
MI= MR16 halogen, 6V-6W
MJ= MR16 halogen, 6V-10W
MK= MR16 halogen, 12V-12W
MA= MR16 halogen, 12V-20W
Other models available.
Consult your sales representative.
Project/Location:
Contractor:
12ESL-EX Series
Date:
High Capacity Combination Unit
FEATURES
TYPICAL SPECIFICATIONS
• Standard 120/347VAC input
Supply and install the Emergi-Lite® 12ESL-EX Series “Exit” a unit
that combines an illuminated LED Exit Sign with an emergency light
battery unit. The housing and faceplate shall be constructed of steel.
The faceplate shall come standard with knockout chevrons. The light
source for the Exit Sign shall be LED. The LED lamps shall provide
illumination in normal and emergency operation. Red LEDs shall be
of ALINGAP technology. The charger board, the battery and the LEDs
shall be contained in a single housing. A diffuser optimized for LEDs
shall be mounted behind the legend to provide the 6” high by 3/4”
stroke letters with even illumination. The unit shall include a test
switch and high charge pilot light. The equipment shall be designed
to furnish exit illumination from the normal AC source. When a power
failure occurs, the Exit Sign along with the emergency heads shall
illuminate for a minimum of 30 minutes. The power available for
emergency lights shall be at least 110W or as otherwise specified. The
heads shall require no tools to aim and shall be as specified. The Exit
Sign shall be CSA-C860 approved and meets CSA 22.2 No. 141.
The equipment shall be Emergi-Lite® Model:
.
• Wide range of lamp heads available
• Solid-state pulse-type charger standard
• Sealed dust-proof transfer relay
• Auto-diagnostic charger available (110W only)
• Meets or exceeds CSA 22.2 No. 141.
DIMENSIONS
137/8” [35.3 cm]
101/4” [26 cm]
161/8” [41 cm] up to 144W
231/8” [59 cm] 250W and 360W
161/8” [41 cm]
Dimensions are approximate and subject to change.
EXIT
Prepared by:
51/2” [13.8 cm]
WIRE GUARDS
51/2” [13.8 cm]
460.0081-E
460.0034-E
POWER CONSUMPTION AND UNIT RATING
MODEL
*Housing width is 231/8 for 250W and 360W capacity only (cabinet C). For more information
please consult your sales representative
WATTAGE CAPACITY
AC SPECS
Exit Sign Module
12ESL110
12ESL144
12ESL250
12ESL360
Less than 2W
0.25/0.10 A
0.25/0.10 A
0.45/0.15 A
0.45/0.15 A
120/347VAC
Wall Mount 110W and 144W
Wall Mount 250W and 360W
30MIN
1H00
1H30
2H00
4H00
110
144
250
360
64
84
144
210
45
60
100
150
36
48
83
120
18
24
42
60
ORDERING INFORMATION
SERIES, VOLTAGE
AND WATTAGE
12ESL110= 12V - 110W
12ESL144= 12V - 144W
12ESL250= 12V - 250W
12ESL360= 12V - 360W
COLOUR
Blank= f actory
white
B= black
LETTERING
VOLTAGE
OPTIONS
EX= EXIT
Blank=
120/347VAC
2= 277VAC
Blank= no options
U= autodiagnostics
(110W only)
EXAMPLE: 12ESL110EX/2M
52
# OF
HEADS
/0= no
heads
/1= one
head
/2= two
heads
/3= three
heads
HEADS STYLE AND WATTAGE
Blank= large tungsten, 12V-9W, wedge base
-18= large tungsten, 12V-18W, wedge base
-25= large tungsten, 12V-25W, DCB
150MK= MR16 Deco head EF150, 12V-12W
150MA= MR16 Deco head EF150, 12V-20W
150MB= MR16 Deco head EF150, 12V-35W
150MC= MR16 Deco head EF150, 12V-50W
LG= MR16 LED, 12V-4W
LI= MR16 LED, 12V-5W
LJ= MR16 LED, 12V-6W
H= large halogen, 12V-8W, quartz sealed beam
H12= large halogen, 12V-12W, quartz sealed beam
M= mini tungsten, 12V-9W, wedge base
M18= mini tungsten, 12V-18W, wedge base
MQ= mini halogen, 12V-8W, quartz bi-pin
MQ12= mini halogen, 12V-12W, quartz bi-pin
MK= MR16 halogen, 12V-12W
MA= MR16 halogen, 12V-20W
Q= large halogen, 12V-8W, quartz bi-pin
Q12= large halogen, 12V-12W, quartz bi-pin
Q20= large halogen, 12V-20W, quartz bi-pin
Q55= large halogen, 12V-55W, quartz bi-pin
S12= large tungsten, 12V-12W, sealed beam
S18= large tungsten, 12V-18W, sealed beam
S25= large tungsten, 12V-25W, sealed beam
Project/Location:
Contractor:
12ESL-SR Series
Date:
High Capacity Combination Unit
Prepared by:
TYPICAL SPECIFICATIONS
FEATURES
Standard 120/347VAC input
Selection of lamp head styles
Solid state pulse type charger standard
Sealed dust-proof transfer relay
Optional self-diagnostic charger (110W only)
Available in 12V, 110, 144, 250 and 360W
Long life, maintenance free lead acid battery
Fully C860 approved “SORTIE” legend illuminated with ALINGAP
LEDs and meets or exceeds CSA 22.2 No. 141.
• High-quality steel enclosure with corrosion-resistant undercoating
•
•
•
•
•
•
•
•
Supply and install the Emergi-Lite® 12ESL-SR Series LED “SORTIE’’
combo unit. The housing and faceplate shall be constructed of steel.
The faceplate shall come standard with knockout chevrons.
The light source shall be light emitting diodes (LED). The LED lamps
shall provide illumination in normal and emergency operation. Red
LED technology shall be ALINGAP. The power pack, rechargeable
battery and LEDs shall be contained in a single housing. A diffuser
optimized for LEDs shall be mounted behind the legend to provide
the 6” high by 3/4” stroke letters with even illumination. The power
pack is furnished with a test switch and high charge pilot light. The
unit shall be designed to provide Exit Sign illumination from the
normal AC source. When a power failure occurs, the mounted heads
along with the Exit Sign are illuminated in emergency mode for a
minimum of 30 minutes. The power available for emergency lights
shall be 110W or as otherwise specified. The heads shall require no
tools to adjust and aim. The heads will be constructed of durable
thermoplastic and use 6V, 9W lamps or as otherwise specified. The
Exit Sign shall be CSA-C860 approved and meets CSA 22.2 No. 141.
The equipment shall be Emergi-Lite® Model:
DIMENSIONS
Dimensions are approximate and subject to change.
101/4”
[26.1 cm]
137/8” [35.4 cm]
161/8” [41.1 cm]
CABINET C
WIRE GUARDS
460.0034-E
231/8” [58.8 cm]
51/2” [13.8 cm]
Wall Mount
51/2” [13.8 cm]
POWER CONSUMPTION AND UNIT RATING
MODEL
AC SPECS
Sortie Sign Module
12ESL110
12ESL144
12ESL250
12ESL360
30MIN
Less than 2W
0.25/0.10 A
0.25/0.10 A
0.45/0.15 A
0.45/0.15 A
120/347VAC
110
144
250
360
WATTAGE CAPACITY
1H00
1H30
2H00
64
84
144
210
45
60
100
150
36
48
83
120
4H00
18
24
42
60
ORDERING INFORMATION
SERIES, VOLTAGE
AND WATTAGE
12ESL110= 12V - 110W
12ESL144= 12V - 144W
12ESL250= 12V - 250W
12ESL360= 12V - 360W
COLOUR
Blank= factory
white
B= black
LETTERING
VOLTAGE
OPTIONS
SR= SORTIE
Blank=
120/347VAC
2= 277VAC
Blank= n
o
options
U= autodiagnostics
(110W only)
# OF
HEADS
o
/0= n
heads
ne
/1= o
head
/2= t wo
heads
/3= t hree
heads
HEADS STYLE AND WATTAGE
Blank= large tungsten, 12V-9W, wedge base
-18= large tungsten, 12V-18W, wedge base
-25= large tungsten, 12V-25W, DCB
150MK= MR16 Deco head EF150, 12V-12W
150MA= MR16 Deco head EF150, 12V-20W
150MB= MR16 Deco head EF150, 12V-35W
150MC= MR16 Deco head EF150, 12V-50W
LG= MR16 LED, 12V-4W
LI= MR16 LED, 12V-5W
LJ= MR16 LED, 12V-6W
H= large halogen, 12V-8W, quartz sealed beam
H12= large halogen, 12V-12W, quartz sealed beam
M= mini tungsten, 12V-9W, wedge base
M18= mini tungsten, 12V-18W, wedge base
MQ= mini halogen, 12V-8W, quartz bi-pin
MQ12= mini halogen, 12V-12W, quartz bi-pin
MK= MR16 halogen, 12V-12W
MA= MR16 halogen, 12V-20W
Q= large halogen, 12V-8W, quartz bi-pin
Q12= large halogen, 12V-12W, quartz bi-pin
Q20= large halogen, 12V-20W, quartz bi-pin
Q55= large halogen, 12V-55W, quartz bi-pin
S12= large tungsten, 12V-12W, sealed beam
S18= large tungsten, 12V-18W, sealed beam
S25= large tungsten, 12V-25W, sealed beam
Note: Other styles available. Consult your sales
representative.
EXAMPLE: 12ESL110EX/0M
53
Project/Location:
EP Series
Contractor:
Date:
All-Plastic Pictogram Exit Sign
Commercial-grade, universal-mount
and snap-fit
FEATURES
Prepared by:
TYPICAL SPECIFICATIONS
The Emergi-Lite® EP Series is a compact pictogram Exit Sign with
an all-in-one, snap-fit design. Easy to install and affordable, the
EP Series Exit Sign is ideally suited for commercial applications,
especially those in which large numbers of Exit Signs are required.
Supply and install the Emergi-Lite® EP pictogram Exit Sign. The
equipment shall operate with universal 2-wire AC input voltage
of 120 to 347VAC at less than 2.5W and universal 2-wire DC input
voltage from 6 to 24VDC at 1W consumption for single and double
face signs. The sign shall come standard with a canopy and shall be
suitable for wall, end, or ceiling mounting. The frame, faceplates,
back plate and canopy shall each be constructed of a one-piece
UV-stabilized thermoplastic material colored factory white. Each
faceplate shall come standard with two legend films for pictogram
and directional indicators. The light source shall be white
light-emitting diodes (LED) and shall provide even illumination in
normal and emergency operation. The equipment in a
Self-Powered configuration shall use a sealed Nickel-Cadmium
battery of 2.4V nominal voltage. The equipment shall recharge the
battery in 24 hours and stay illuminated at least two hours upon AC
failure.
• Durable, factory white, thermoplastic housing
• Universal mounting: wall-, end-, or ceiling-mount
• Long-life white LED light source
•S
upplied standard with two pictogram films per face, for direction
selection
• Certified CSA 22.2 No.141-10 for pictogram safety signs
•T
wo-wire universal AC input: 120 to 347VAC; two-wire standard
DC input: 6 to 24VDC
•E
nergy efficient – consumes less than 2.5W in AC mode and only
1W in DC-remote
The pictogram Exit Sign shall be listed to the CSA 22.2 No.141-10
standard.
•S
elf-Powered model delivers standard two hours of back-up
lighting
The equipment shall be Emergi-Lite® Model: _________________ .
• Optional vandal-proof shield and tamper-proof screws
DIMENSIONS
Dimensions are approximate and subject to change.
8” [20.3 cm]
87/8” [22.5cm]
61/8” [15.6 cm]
41/2” [11.4 cm]
21/4” [5.7 cm]
121/8” [30.7 cm]
13” [33.0 cm]
POWER CONSUMPTION AND UNIT RATING
MODEL
AC only
AC/DC standard
AC/Special DC
AC SPECS
DC SPECS
120 to 347VAC
120 to 347VAC
120 to 347VAC
Less than 2.5W
Less than 2.5W
Less than 2.5W
6 to 24VDC
36, 48, 120VDC
Less than 1.5W
Less than 2.5W
Two-wire 120V AC/DC
120VAC
Self-Powered
120 to 347VAC
Less than 2.5W
120VDC
Less than 2.5W
Less than 3W
Nickel-Cadmium Battery
Min. 2 hours
ORDERING INFORMATION
SERIES
EP= plastic
sign
LEGEND
Blank= pictogram
FACES/MOUNTING
1= single face, universal
mounting
2= double face, universal
mounting
3= universal face,
universal mounting
ENCLOSURE
COLOUR
W= factory white
B= black
VOLTAGE
I= 120 to 347VAC;
Self-Powered / 2 hours
U= universal 120 to 347VAC;
6 to 24VDC
U00= 120 to 347VAC only
U36= 120 to 347VAC; 36VDC
U48= 120 to 347VAC; 48VDC
U120= 347VAC; 120VDC
24= 6 to 24VDC
2120= 120VAC/VDC
OPTIONS
TP= tamper-proof screws*
VR= vandal resistant shield with
tamper-proof screws*
* Not available with universal face
Unlike EXIT signs, the pictogram sign is not available in double arrow configurations.
EXAMPLE: EP1WUVR
54
Project/Location:
Contractor:
Premier™ Series
Date:
Thermoplastic Exit Sign
Prepared by:
TYPICAL SPECIFICATIONS
FEATURES
• Durable, injection-molded, thermoplastic housing
Supply and install the Emergi-Lite® Premier™ Series Exit Sign.
The standard equipment shall operate with a dual-voltage input
of 120/347VAC with less than 2W of consumption and a universal
two-wire DC input voltage from 6VDC to 48VDC at less than 2.5W for
single and double face signs. The exit shall be suitable for wall, end,
or ceiling mount. The faceplate shall be constructed of durable high
impact thermoplastic. No screws are necessary to hold the faceplate
or the back plate to the housing. The faceplates shall come standard
with snap in/out chevrons. The frame shall consist of one-piece
factory white thermoplastic. The light source shall be light emitting
diodes (LEDs). The LEDs shall provide illumination in normal and
emergency operation and shall be mounted inside the exit housing.
Red LED technology shall be ALINGAP. An LED-sensitive diffuser
shall be mounted in front of the LEDs to provide the 6” high by ¾”
stroke letters with even illumination. The Exit Sign shall be C860
approved.The Exit Sign in a Self-Powered configuration shall be
equipped with a sealed, maintenance-free Nickel-Cadmium battery.
The equipment shall recharge the battery in 24 hours and stay
illuminated at least 90 minutes upon AC failure.
The Self-Powered model equipped with advanced diagnostic shall
self-test by simulating a power failure for one minute every 30 days,
30 minutes every 60 days and 90 minutes every 360 days. A diagnostic
circuit shall continuously monitor the performance of the battery,
charger module and LED lamps. Upon failure detection the system
shall display the error on the AC pilot lamp, which will change color
from green to red and will flash with a specific code. The red light
shall be steady-on in case of “Battery Disconnect”; it shall flash with
one blink for “Battery failure”, two blinks for “Charger failure” and
four blinks for “LED lamp failure. A label with the diagnostic legend
shall be visible next to the pilot light.
.
The equipment shall be Emergi-Lite® Model:
• Long-life, energy-efficient ALINGAP LED light source
•U
niversal mounting - supplied standard with two stencil plates,
red diffusing lens and backplate
• Universal, field-selectable snap in/out chevrons
•A
vailable for wall, end or ceiling mounting
• Energy efficient – consumes less than 3.5W
• Normal AC and emergency DC operation with dual AC input of
120V/347V and universal DC input of 6V to 48V
•C
omes with the Emergi-Lite® EZ2 canopy for quick and easy
installation – see page 40 for more information
• CSA certified, meets or exceeds CSA 22.2 No. 141 requirements
WIRE GUARDS
460.0079-E
Wall Mount
460.0027-E
End Mount
460.0028-E
Ceiling Mount
DIMENSIONS
8” [20.3 cm]
11” [22.9 cm]
Dimensions are approximate and subject to change.
117/8” [30.1 cm]
PREMIER™ FAMILY
2” [5.0 cm]
127/8” [32.8 cm]
POWER CONSUMPTION AND UNIT RATING
MODEL
Premier™ Combo Series
Premier™ Battery Series
P. 56-57
P. 116-117
AC SPECS
DC SPECS
AC only
AC/DC remote
Self-Powered
120/347VAC
120/347VAC
120/347VAC
Less than 2.5W
Less than 2W
Less than 3.5W
6 to 48VDC
Nickel-Cadmium Battery
Less than 1.5W
Minimum 90 minutes
Self-Powewed with diagnostic
120/347VAC
Less than 3W
Nickel-Cadmium Battery
Minimum 90 minutes
ORDERING INFORMATION
SERIES
COLOUR
UNIT CAPACITY
VOLTAGE
PRE= LED plastic
universal
Exit Sign
W= factory
white
B= black
AC= AC only
AC2CI= dual AC circuit (2X 120V)
UD= 120/277 or 120/347VAC & 6 to 48VDC
IN= Self-Powered Nickel-Cadmium
IDN= Self-Powered with self diagnostics
Nickel-Cadmium
NEX= NEXUS® system interface*
NEXRF= wireless NEXUS® system interface*
2= 120/277VAC
3= 120/347VAC
LEGEND COLOUR
R= red
G= green
R1= red single face*
R2= red double face*
G1= green single face*
G2= green double face*
*Used for special wording
signs
*Self-Powered models only
EXAMPLE: PREWAC2R
55
OPTIONS
TP= tamper-proof screws*
VRTP= polycarbonate shield with
tamper-proof screws*
BA= brushed aluminum stencil
990.0119-E= tamper-proof bit**
*Specify single or double face, red
or green.
** One bit needed per order
Project/Location:
Contractor:
Premier™ Series
Date:
Thermoplastic Combination Unit
Prepared by:
FEATURES
TYPICAL SPECIFICATIONS
The PremierTM Series of combination units (emergency light battery
unit with an Exit Sign) are designed with aesthetics, ease of
installation and performance in mind.
• One-pack combination of battery unit and Exit Sign, a compact
and contemporary design
Supply and install the Emergi-Lite® Premier™ Series
combination emergency light battery unit and Exit Sign. The
standard equipment shall operate with a dual voltage input of
120/347VAC. The unit shall be suitable for wall or ceiling mount.
The unit frame and face plates shall be made of injection-molded
durable high-impact thermoplastic and come standard with snap
in/out chevrons. No screws are necessary to hold the faceplate
or backplate to the housing. The one-piece thermoplastic frame
is molded in white (optional black). The faceplates shall feature
a uniformly illuminated legend. The light source shall be light
emitting diodes (LED) and shall provide illumination in normal and
emergency operation and shall be mounted inside the combination
housing. Red LED technology shall be ALINGAP. An LED-sensitive
diffuser shall be mounted behind the legend to provide the 6” high
by 3/4” stroke letters with even illumination.
•D
urable injection-molded thermoplastic housing with
push-to-snap design
•A
vailable in single or double face configurations both with
means for ceiling mounting
®
• C omes with the Emergi-Lite Premier™ EZ2 canopy and
field-selectable snap chevrons for quick and easy installation
• Exit Sign module illuminated by long-life ALINGAP red LEDs
•T
wo MR16 halogen lamps, shielded by a clear polycarbonate
cover
The unit shall be equipped with two emergency heads with
tool-less adjustable swivels (lamps of 12W or less) and long-life
MR-16 type lamps of ___ V and ___ W. Each lamp shall be
protected by a snap-on, shock-absorbent, transparent
polycarbonate cover.
•O
ptional MR16 LED lamps with life expectancy 50,000+ hours
• S ealed, maintenance-free, Lead-Calcium or
Nickel-Metal-Hydride batteries
• Remote load capacity up to 92W
The unit shall be equipped with a test switch and a green pilot
light, located on the face plate above the EXIT legend. The battery
charger shall be driven by a micro-controller. All electronic
circuitry (charger, LED driver, LED’s) shall be installed on a single
printed circuit board PCB.
• Dual voltage input: 120/347VAC or 120/277VAC.
• Optional vandal-resistant shield with tamper-proof screws
• Certified CSA C22.2 No.141
• Optional advance diagnostics circuitry available
The unit equipped with self-testing / self-diagnostic features shall
automatically self test for one minute every 30 days, 10 minutes in
the 6th month and 30 minutes annually. When a fault is detected,
the bi-color pilot light shall turn from green to red and shall flash,
identifying the source of the failure: battery, charger circuitry, lamp
load, LED strip. The Exit Sign module shall be CSA-C860 approved
The combo unit shall be Emergi-Lite® Model:
PREMIER™ FAMILY
.
WIRE GUARDS
460.0078-E
Premier™ Exit Series
Premier™ Battery Series
P. 55
P. 116-117
Wall Mount
POWER CONSUMPTION
MODEL
AC SPECS
Exit Sign Module
Less than 2W
L2
L5
L5A
H5A
H10A
0.11/0.04 A
120/347VAC
0.22/0.08 A
WATTAGE CAPACITY
30MIN
1H00
1H30
2H00
4H00
-
-
-
-
-
20
15
12
8
-
50
30
24
16
8
50
30
24
16
8
50
36
24
18
9
100
72
48
36
18
56
Project/Location:
Contractor:
Premier™ Series
Date:
Thermoplastic Combination Unit
Prepared by:
DIMENSIONS
Dimensions are approximate and subject to change.
111/4” [28.7 cm]
123/8” [31.5 cm]
47/8” [12.3 cm]
17” [43.2 cm]
33/8” [8.6 cm]
ORDERING INFORMATION
SERIES
PRE1= single face
ceiling or
wall mount
PRE2= double face
ceiling mount
PRE1N= single face
wall mount
(less
canopy)
PREU= universal,
2 faces
backplate
and canopy
COLOUR
W=
factory
white
B=
black
VOLTAGE
POWERPACK
LEGEND
3= 120/347VAC
2= 120/277VAC
-L2= 6V-20W
Lead cal
-L5= 6V-50W
Lead cal
2V-50W
-L5A= 1
Lead cal
-H5A= 12V-50W
NiMH
-H10A=
12V-100W
NiMH
Blank=
red legend
G= green
legend
OPTIONS
Blank= no options
-TP= tamper-proof screws
-VRTP= vandal-resistant shield with
tamper-proof screws
D3= time delay (15 minutes)
U= auto-diagnostics
UN= auto-diagnostics, non-audible
990.0119-E= tamper-proof bit
NEX= NEXUS® system interface*
NEXRF= wireless NEXUS® system
interface*
BA= brushed aluminum exit stencil
*Consult your sales representative for options
available with the NEXUS® system.
EXAMPLE: PRE1W3-L2/2MI
57
# OF
HEADS
HEAD STYLE/
WATTAGE
Blank= n
o
heads
2= two heads
LA= MR16 LED,
6V-4W
LG= MR16 LED,
12V-4W
LI= MR16 LED,
12V-5W
LJ= MR16 LED,
12V-6W
MI= MR16
halogen,
6V-6W
MJ= MR16
halogen,
6V-10W
MO= MR16
halogen,
12V-10W
MK= MR16
halogen,
12V-12W
Project/Location:
Contractor:
C8SRPK Series
Date:
NEMA-3R Certified “Sortie” Sign
Prepared by:
FEATURES
TYPICAL SPECIFICATIONS
•G
asketed fiberglass housing designed specially for industrial
applications
Supply and install Emergi-Lite® C8SRPK Series “SORTIE” Exit Signs.
The equipment shall operate with universal two-wire AC input voltage
from 120VAC to 347VAC at less than 1.5W and universal two-wire DC
input voltage from 6VDC to 24VDC at less than 1.5W per face.
• Units are certified NEMA-3R
• Sealed, vandal-resistant clear polycarbonate faceplate
•W
ater, dust and oil resistant, suitable for high abuse areas, wet
locations
•L
ong life, even illumination of the legend provided by
energy-efficient ALINGAP technology LED light source
consuming less than 3W per face
•W
all, ceiling or end mount. Mounting bracket available for ease
of installation
•N
ormal AC and emergency DC operation – 120V to 347VAC and
6V to 24VDC input
• CSA certified, meets or exceeds CSA 22.2 No. 141 requirements
The sign housing shall be of grey fiberglass, specially designed for
industrial environments. The sealed faceplate shall be gasketed,
completely transparent, high abuse and vandal resistant, and will
feature an even illuminated legend.
The light source illuminating the legend shall be ALINGAP technology
red LEDs. The exit in a Self-Powered configuration shall include a
magnetic test switch and a Nickel-Cadmium battery. The Exit Sign
shall stay illuminated during emergency operation for at least 60
minutes upon AC failure.
The Exit Sign shall be CSA-C860 approved and meets CSA 22.2 No.141.
The equipment shall be Emergi-Lite®Model:
.
WIRE GUARDS
DIMENSIONS
195/8” [49.8 cm]
460.0103-E
Wall Mount
460.0104-E
Ceiling Mount
Double face
Single face
121/4” [31.1 cm]
Dimensions are approximate and subject to change.
2” [4.9 cm]
37/8” [9.8 cm]
POWER CONSUMPTION AND UNIT RATING
MODEL
AC SPECS
DC SPECS
AC/DC standard, red
120 to 347VAC
Less than 1.5W
6 to 24VDC
Less than 1.5W
AC/special DC, red
120/277/ 347VAC
Less than 2.5W
36 or 48 or 120VDC
Less than 2.5W
Self-Powered, red
120 to 347VAC
Less than 3W
Nickel-Cadmium battery
Minimum 60 minutes
Note: double face models have double the power consumption above.
ORDERING INFORMATION
SERIES
C8SRPK1= SORTIE, single face, wall, end and ceiling mount
C8SRPK2= SORTIE, double face, wall, end or ceiling mount
SUPPLY AND VOLTAGE
U= 120 - 347VAC 6/12/24VDC
EM120-2W= 120VAC, 120VDC 2 wires
U36= 120/277/347VAC - 36VDC 4 wires
U48= 120/277/347VAC - 48VDC 4 wires
U120= 120/277/347VAC - 120VDC 4 wires
I= Self-Powered, 120-347VAC
EXAMPLE: C8SRPK1U
Special wording available. see page ____. Please consult your sales representative.
58
Project/Location:
C8ESPK & C8SEPK
Series
Contractor:
Date:
Prepared by:
NEMA-3R Certified Bilingual Sign
TYPICAL SPECIFICATIONS
FEATURES
• Certified NEMA-3R
Supply and install Emergi-Lite® C8ESPK or C8SEPK Series
Bilingual LED Exit Sign. The equipment shall operate with universal
two-wire AC input voltage from 120VAC to 347VAC at less than
3W per face and universal two-wire DC input voltage from 6VDC
to 24VDC at less than 3W per face. The housing shall be of gray
fiberglass, gasketed, specially designed for industrial environments. The sealed front cover shall be constructed of heavy-duty
vandal-resistant transparent polycarbonate of 4mm thickness and
shall be bent around the back box for increased rigidity. The front
cover will feature an even illuminated legend with the text ”EXIT”
and “SORTIE” positioned one on top of the other.
•G
asketed fiberglass housing designed specifically for industrial
applications
• Grey finish
• Sealed, vandal-resistant polycarbonate faceplate
•W
all or ceiling mounting; wall or ceiling brackets available for
easy installation
•N
ormal AC and emergency DC operation –
120 to 347V AC input; 6 to 24 DC input
• Meets or exceeds CSA 22.2 No. 141.
The light source shall be the new ALINGAP technology red LED.
The equipment shall be suitable for wall or ceiling mount and be
designed specifically for high abuse areas, wet locations, dust and
oil-tight applications. The equipment in a Self-Powered
configuration shall stay illuminated during emergency operation for
at least 60 minutes upon AC failure.
WIRE GUARDS
460.0103-E
Wall Mount
460.0104-E
Ceiling Mount
The equipment shall be NEMA-3R and C-860 approved and meets
CSA 22.2 No. 141.
DIMENSIONS
The equipment shall be Emergi-Lite® Model:
.
241/8” [61.4 cm]
15” [38.1 cm]
Double face
Single face
15” [38.1 cm]
Dimensions are approximate and subject to change.
2” [4.9 cm]
241/8” [61.4 cm]
37/8” [9.8 cm]
POWER CONSUMPTION AND UNIT RATING
MODEL
AC SPECS
DC SPECS
AC/DC, red
120 to 347VAC
Less than 3W
6 to 24VDC
Less than 3W
Self-Powered, red
120 to 347VAC
Less than 5W
Nickel-Cadmium battery
Minimum 60 minutes
Note: double face models have double the power consumption above.
ORDERING INFORMATION
SERIES
POWER SOURCE AND VOLTAGE
C8ESPK1= single face EXIT over SORTIE
C8SEPK1= single face SORTIE over EXIT
C8ESPK2= double face EXIT over SORTIE
C8SEPK2= double face SORTIE over EXIT
-U= 120 to 347VAC, 6 to 24VDC
-I= Self-Powered, 120 to 347VAC
EXAMPLE: C8ESPK1-U
59
Project/Location:
C8SRPK-P Series
NEMA-3R Certified Combination Unit
FEATURES
•T
his unit is ideal for schools, parking garages, public places,
transit platforms and security areas such as jails
• Units are NEMA-3R cerfified
•G
asketed fiberglass housing designed specially for industrial
applications
• Sealed, vandal-resistant clear polycarbonate faceplate
• Fully integrated unit with charger and rechargeable battery
• Water and snow resistant, suitable for areas subject to
vandalism and wet locations
•S
olid state charger circuitry – capable of full recharge within 24
hours
• Low voltage disconnect circuitry
• Sealed, dust-tight transfer relay
•E
xit light source is ALINGAP technology LED
•P
ower pack includes a magnetic test switch and a high charge
pilot light
• In emergency mode, the long life, sealed nickel battery provides
power to the Exit Sign and lamp heads for a minimum of 30
minutes
Contractor:
Date:
Prepared by:
TYPICAL SPECIFICATIONS
Supply and install Emergi-Lite® C8SRPK-P Series industrial combo
unit. The unit shall be fabricated of industrial grade polycarbonate
designed specifically for industrial environments. The sealed front
cover shall be fabricated of high abuse and vandal-resistant
polycarbonate, and feature an evenly illuminated legend. The word
“SORTIE” shall be illuminated by long life LEDs consuming less than
1.5W per face. The light source shall be ALINGAP technology red LED.
The Exit Sign shall be certified NEMA-3R and designed specifically for
applications such as high abuse areas, wet locations, environments
requiring dust and oil tight equipment or cold temperatures. It shall be
designed to provide normal AC illumination and upon AC failure, the
Exit Sign and lamp heads shall stay illuminated in emergency mode for
a minimum of 30 minutes. The power pack is supplied with a magnetic
test switch and a high charge pilot light.
The combo unit shall be CSA-C860 and NEMA-3R certified and meets
CSA 22.2 No. 141.
The equipment shall be Emergi-Lite® model: _____________________.
WIRE GUARDS
• CSA certified, meets or exceeds CSA 22.2 No. 141 requirements
60
460.0034-E
Wall Mount
460.0104-E
Ceiling Mount
460.0124-E
Double Face, End Mount
Project/Location:
Contractor:
C8SRPK-P Series
Date:
NEMA-3R Certified Combination Unit
Prepared by:
DIMENSIONS
Dimensions are approximate and subject to change.
DOUBLE FACE
95/16” [23.6 cm]
SINGLE FACE
121/4” [31.1 cm]
1213/16” [32.5 cm]
75/16” [18.6 cm]
2” [4.9 cm]
195/8” [49.8 cm]
37/8” [9.8 cm]
POWER CONSUMPTION AND UNIT RATING
MODEL
WATTAGE CAPACITY
AC SPECS
C8SRPK1= single face
C8SRPK2= double face
120/347VAC
30MIN
1H00
1H30
2H00
4H00
0.15/0.06 A
36
21
15
12
6
0.15/0.06 A
72
42
30
24
12
Note: double face models have double the power consumption above
ORDERING INFORMATION
SERIES
VOLTAGE
SUPPLY AND VOLTAGE
C8SRPK1= SORTIE,
single face
C8SRPK2= SORTIE,
double
face
Blank=
120/347VAC
P3= 6V-36W
P7= 6V-72W
NUMBER OF HEADS
Blank= no heads
/1= one head
/2= two heads
LAMP TYPE AND WATTAGE
Blank= tungsten, 6V-9W, par 36
-18= tungsten, 6V-18W, par 36
-25= tungsten, 6V-25W, par 36
H= halogen, 6V-8W, sealed beam
H12= halogen, 6V-12W, sealed beam
H20= halogen, 6V-20W, sealed beam
Q= halogen, 6V-8W, par 36
Q12= halogen, 6V-12W, par 36
Q20= halogen, 6V-20W, par 36
S= tungsten, 6V-8W, sealed beam
S18= tungsten, 6V-18W, sealed beam
S25= tungsten, 6V-25W, sealed beam
Rubber heads also available.
EXAMPLE: C8SRPK1P3H
61
OPTIONS
FP= lens with
teflon coating
Survive-All™
EN Series
Project/Location:
Contractor:
Date:
NEMA-4X & NSF Certified
Pictogram Sign
FEATURES
• NEMA-4X Certified
• NSF compliant for food processing
•P
olymeric enclosure is fully gasketed around lens and canopy to
secure against water leaks
• Sealed, heavy-duty, vandal-resistant polycarbonate face plate
• Suitable for cold weather: -40°C for AC/DC and -20°C for
Self-Powered models (option: -CW)
• Tamper-resistant, concealed test switch with magnetic action
• White LED light source
• Supplied standard with two pictogram films per face, for direction
selection
• Meets or exceeds CSA 22.2 No.141-10 standard for pictogram
Exit Signs
• Universal AC input: two-wire 120 to 347VAC; Standard DC input:
two-wire 6 to 24VDC
• Energy efficient – consumes less than 2.5W in AC or DC-remote
mode
•S
elf-Powered models deliver two hours of back-up lighting
NEMA-4X
The equipment shall be Emergi-Lite® Model:
Dimensions are approximate and subject to change.
14” [35.7 cm]
POWER CONSUMPTION AND UNIT RATING
MODEL
PICTOGRAM >
RIGHT FROM HERE
31/2” [8.7 cm]
37/8” [9.9 cm]
91/4” [23.4 cm]
PICTOGRAM
STRAIGHT FROM
HERE
DOUBLE FACE
TYPICAL SPECIFICATIONS
Supply and install the Emergi-Lite® Survive-All™ EN Series pictogram
Exit Signs. The equipment shall be certified for NEMA- 4X and
designed specifically for high abuse areas, wet locations, and cold
weather applications. The equipment frame shall be of industrial
grade polyvinyl chloride with a gasket around lenses and canopy.
The faceplate(s) shall be constructed of heavy-duty vandal-resistant
polycarbonate and feature an even illuminated legend. Each face plate
shall come standard with two legend films for pictogram and direction
selection. The light source shall be white light-emitting diodes (LED).
The pictogram Exit Sign shall operate with universal 2-wire AC input
voltage of 120 to 347VAC at less than 2.5W and universal 2-wire DC
input voltage from 6 to 24VDC at less than 1W for single and double
face signs. The Self-Powered model shall include a concealed green
pilot light and magnet-sensitive test switch, shall use a sealed
Nickel-Cadmium battery of 2.4V nominal voltage and shall stay
illuminated during emergency operation for at least two hours upon
AC failure. When specified, the Self-Powered model shall include
auto-test functions: it shall execute automatic tests for 5 minutes every
30 days, 30 minutes every 60 days and two hours annually. When a fault
is detected, the bi-colour pilot light shall turn from green to red and
flash following a particular code. The code description shall be visible
on a label next to the pilot light to identify the failure type: battery,
charger circuitry, or LED lamps.
The pictogram Exit Sign shall be listed CSA 22.2 No.141-10 standard.
DIMENSIONS
131/4” [33.6 cm]
Prepared by:
< PICTOGRAM
LEFT FROM HERE
SINGLE FACE
AC SPECS
AC-only
AC/DC standard
AC/Special DC
SURVIVE-ALL NEMA 4X & NSF CERTIFIED FAMILY
™
120 to
347VAC
120 to
347VAC
120 to
347VAC
Two-wire 120V
AC/DC
120VAC
Self-Powered
120 to
347VAC
Auto test
120 / 347VAC
DC SPECS
Less than
2.5W
Less than
2.5W
Less than
2.5W
Less than
2.5W
Less than
3W
Nickel-Cadmium
battery
Less than
1W
Less than
2.5W
Less than
2.5W
Min. 2
hours
Less than
3.5W
Nickel-Cadmium
battery
Min. 2
hours
6 to 24VDC
36, 48, 120VDC
120VDC
-
WIRE GUARDS
ENC SERIES
P. 64
LPEX600
LPEX600-N
SERIES
SERIES
P. 63
P. 65
NXM SERIES
460.0079-E
EF39 & EF39P
SERIES
P.120-121
P.148-149
ORDERING INFORMATION
SERIES
EN= NEMA-4X
& NSF
pictogram
exit sign
FACES/ MOUNTING
COLOUR
1= single face universal W= factory
mounting
white
2= double face
B= black
universal mounting
End mount
460.0028-E
Ceiling mount
VOLTAGE
I= 120 to 347VAC; Self-Powered / 2 hours
ID= 1
20/347VAC; Self-Powered / 2 hours c/w non-audible diagnostic
ID2= 120/ 277VAC; Self-Powered / 2 hours c/w non-audible diagnostic
U= universal 120 to 347VAC; 6 to 24VDC
U00= 120 to 347VAC only
U36= 120 to 347VAC; 36VDC
U48= 120 to 347VAC; 48VDC
U120= 120 to 347VAC; 120VDC
EM120-2W= 2-wires 120VAC/VDC
EXAMPLE: EN1WICW
62
Wall mount
460.0027-E
OPTIONS
Blank= no options
NEX= NEXUS® system
interface*
NEXRF= wireless NEXUS®
system interface*
CW= cold-weather (-20°C for
ID & ID2 only, -40°C for
AC/DC)
*Note: some options are not available
with the NEXUS® system
Project/Location:
Survive-All™
LPEX600 Series
Contractor:
Date:
Polyvinyl Chloride Exit Sign
Prepared by:
FEATURES
TYPICAL SPECIFICATIONS
• NEMA-4X certified
• NSF certified for food processing
• Polyvinyl chloride enclosure is fully gasketed around lens and
canopy to prevent water infiltration
• Sealed faceplate of heavy-duty, vandal-resistant polycarbonate with
evenly illuminated legend
• Suitable for cold weather: -40°C on non Self-Powered sign and
-25°C on Self-Powered (“CW” option)
• Tamper-resistant magnetic test switch
• Self-diagnostic circuitry standard on all Self-Powered models
• Energy efficient – consumes less than 3W in AC or DC mode
• Normal AC and emergency DC operation –
120 to 347V universal AC dual tap; 6 to 48V universal DC
®
• NEXUS compatible
Supply and install Emergi-Lite® Survive-All™ LPEX600 Series LED Exit
Signs. The equipment shall operate with universal two-wire AC input
voltage from 120VAC to 347VAC at less than 3W and universal two-wire
DC input voltage from 6VDC to 48VDC at less than 2W for single and
double face signs. The equipment frame shall be of industrial grade
polyvinyl chloride with a gasket around lenses and canopy designed
specifically for hostile environments. The faceplate(s) shall be
constructed of heavy-duty vandal-resistant polycarbonate and feature
an even illuminated legend. The light source shall be light emitting
diodes (LED). Red LED technology shall be ALINGAP. An LED-sensitive
diffuser shall be mounted behind the legend to provide the 6” high by
3/4” stroke letters with even illumination. The exit shall be certified
for NEMA- 4X and designed specifically for high abuse areas, wet
locations, and cold weather -20°C (-4°F) applications.
The Self-Powered model shall stay illuminated during emergency
operation for at least 90 minutes upon AC failure and shall include a
magnetic test switch and self-testing and self-diagnostic functions.
The equipment shall automatically self test for 5 minutes every 30
days, 30 minutes every 60 days and 90 minutes annually. A “Service
Required” lamp shall be located near the test switch and flash when a
fault is detected. A two-LED diagnostic display shall be located inside
the equipment and shall identify the eventual source of failure (battery,
charger circuitry, or LED lamps).
• Meets or exceeds CSA 22.2 No. 141.
NEMA-4X
DIMENSIONS
The Exit Sign shall be CSA-C860 approved and meets CSA 22.2 No. 141.
Dimensions are approximate and subject to change.
The equipment shall be Emergi-Lite® Model:
14” [35.7 cm]
31/2” [8.7 cm]
37/8” [9.9 cm]
13 ” [33.6 cm]
1/4
POWER CONSUMPTION AND UNIT RATING
91/4” [23.4 cm]
MODEL
SINGLE FACE
DOUBLE FACE
.
SURVIVE-ALL™ NEMA 4X & NSF CERTIFIED FAMILY
AC SPECS
DC SPECS
AC/DC red
120 to 347VAC
Less
than 3W
AC/DC green
120 to 347VAC
Less
than 3W
6 to 48VDC
Less
than 2W
Self-Powered
red
120 to 347VAC
Less
than 3W
Nickel-Cadmium
battery
Min. 90
minutes
Self-Powered
green
120 to 347VAC
Less
than 3W
Nickel-Cadmium
battery
Min. 90
minutes
6 to 48VDC
Less
than 2W
WIRE GUARDS
460.0079-E
ENC SERIES
P. 64
EN SERIES
P. 62
LPEX600-N SERIES
P. 65
NXM SERIES
P.120-121
EF39 & EF39P
SERIES
P.148-149
Wall Mount
460.0027-E
End Mount
460.0028-E
Ceiling Mount
ORDERING INFORMATION
SERIES
LPEX60=
NEMA-4X
& NSF Exit
Sign
FACES/
MOUNTING
2= single face,
universal
mount
3= double face,
universal
mount
HOUSING FACEPLATES
COLOURS
WW= white/white
BB= black/black
BW= black/ white
WB= white/black
GW= grey/ white
GB= grey/black
WA= white/aluminum
BA= black/aluminum
GA= grey/aluminum
VOLTAGE
U= universal 120-347VAC, 6-48VDC
(-40°C standard)
20-347VAC, Self-Powered c/w
ID= 1
diagnostics (non-audible)
EM120-2W= 120VAC,120VDC 2 wires
OPTIONS
Blank= no options
-G= green legend
CW= cold weather
(-25°C for Self-Powered)
NEX= NEXUS® system interface*
NEXRF= wireless NEXUS® system
interface*
*Self-Powered models only.
EXAMPLE: LPEX602WWU4X
63
4X
4X = approved
NEMA-4X
and NSF
Survive-All
ENC Series
Project/Location:
™
Contractor:
Date:
NEMA-4X & NSF Certified
Pictogram Combination Unit
FEATURES
•C
ertified NEMA-4X for wall or ceiling mount
• NSF certified certified for use in food processing areas
• Meets or exceeds CSA 22.2 No.141-10 standard for pictogram
Exit Signs
• Polyvinyl chloride frame, with built-in gasket to prevent water
infiltration
• Sealed, vandal-resistant faceplate of polycarbonate
• Legend illuminated by long-life white LED’s
• Comes standard with two pictogram films per face, for direction
selection
• Two high-performance MR16 LED lamps shielded by a clear
polycarbonate cover
• O ptional 5W LED emergency lights provide 60’ of egress
illumination on a 6-foot wide path
• Sealed, maintenance-free Lead-Calcium or Nickel-Cadmium
batteries
• Remote load capacity: covers with 4W LED lights 100’ up to 230’ of
egress illumination
• Comes standard with auto-diagnostic
• Cold-weather option: -40°C (-40°F) with only 14W extra power
consumption
NEMA-4X
DIMENSIONS
Dimensions are approximate and subject to change.
37/8” [9.9 cm]
31/2” [8.7 cm]
MODEL
91/4” [23.4 cm]
125/8” [32.1 cm]
PICTOGRAM
STRAIGHT FROM HERE
TYPICAL SPECIFICATIONS
Supply and install Emergi-Lite® Survive-All™ ENC Series combination
emergency light battery unit and pictogram Exit Sign. Designed
specifically for industrial environments, the equipment frame shall be
of industrial grade polyvinyl chloride with gaskets around both sides of
frame contour. The back plate shall be made of 1/8” thick aluminum
sheet and shall include knock-outs for installation on an electrical box.
The faceplate(s) shall be constructed of heavy-duty vandal-resistant clear
polycarbonate and feature a uniformly illuminated pictogram legend.
Each face plate shall come standard with two legend films for pictogram
and direction selection. The light source shall be long-life white lightemitting diodes (LED). The unit shall have attached a lower compartment
containing two emergency heads with adjustable swivels and long-life
MR-16 LED lamps of ___ V and ___ W. The heads shall be installed on
a shield housing made of rigid thermoplastic and shall be protected by
a shock-absorbent, clear polycarbonate cover. The standard AC input
voltage shall be 120/347VAC. The unit shall be equipped with a magnetic
test switch and an LED pilot light protected by the clear face plate. The
unit shall perform auto-test functions managed by a micro-controller and
shall automatically self-test for one minute every 30 days, 10 minutes
in the 6th month and 30 minutes annually. When a fault is detected, the
bi-colour pilot light shall turn from green to red and flash following a
particular code. The code description shall be displayed on a label next
to the pilot light to identify the failure type: battery, charger circuitry, LED
lights for the signage, or emergency lights.
The combination unit shall meet or exceed the standard CSA C22.2
No.141-10. The equipment shall be Emergi-Lite® Model:
POWER CONSUMPTION
14” [35.7 cm]
131/4” [33.6 cm]
< PICTOGRAM
LEFT FROM HERE
Prepared by:
EMERGENCY POWER FOR
LAMPS
AC SPECS
30MIN 1H00 1H30 2H00 4H00
Pictogram
120/347VAC
Sign Module
ENC-6L36
PICTOGRAM >
RIGHT FROM HERE
DOUBLE FACE
ENC6L36-CW
ENC-6N36
ENC6N36-CW
ENC-12N60
SINGLE FACE
SURVIVE-ALL™ NEMA 4X & NSF CERTIFIED FAMILY
120/347VAC
Less than
2.5W
-
-
-
-
-
0.10/0.03 A
36
21
15
12
-
0.25/0.08 A
36
21
15
12
-
0.10/0.03 A
36
30
20
16
8
0.25/0.08 A
36
30
20
16
8
0.18/ 0.06 A
60
40
30
20
10
WIRE GUARDS WITH HEADS
EN SERIES
LPEX600 SERIES
LPEX600-N
NXM SERIES
SERIES
P. 62
P. 63
460.0078-E
460.0060-E
EF39 & EF39P
SERIES
P. 65
P.120-121
Wall Mount
End or Ceiling Mount
P.148-149
ORDERING INFORMATION
SERIES
ENC= NEMA-4X
& NSF
pictogram
exit
combo
unit
FACES /
MOUNTING*
HOUSING
COLOUR
BATTERY TYPE AND
POWER
HEAD STYLE AND
WATTAGE
OPTIONS
1= single face
2= double face
B= black
W= factory
white
6N36= 6V-36W
Nickel-Cadmium
12N60= 12V-60W
Nickel-Cadmium
Blank= no heads
LA= MR16 LED, 6V-4W
LG= MR16 LED, 12V-4W
LI= MR16 LED, 12V-5W
LJ= MR16 LED, 12V-6W
MI= MR16 halogen, 6V-6W
MJ= MR16 halogen, 6V-10W
MK= MR16 halogen, 12V-12W
Blank= advanced diagnostic, non-audible (standard)
-2= 120/277VAC input
D3= time delay (15 minutes)
NEX= NEXUS® system interface*
NEXRF= wireless NEXUS® system interface*
CW= cold-weather -40°C (-40°F) to + 25°C (77°F)
only with 6V single-face units
U= advanced diagnostic
*Universal
mounting
EXAMPLE: ENC2W12N60LD7
64
*Some options are not available with NEXUS®.
Survive-All™
LPEX600-N Series
Project/Location:
Contractor:
Date:
NEMA-4X & NSF Certified
Combination Unit
Prepared by:
FEATURES
TYPICAL SPECIFICATIONS
• NEMA-4X certified for wall or ceiling mount
• NSF certified for food processing
• High efficiency MR16 lamps up to 12V, 12W or white LED
emergency lights
• Continuous self-diagnostic monitoring and monthly self-testing
• Fully automatic charger is solid state
• Non-intrusive magnetic test switch
• Cold weather (-40°C) option
• Comes standard with tamper-proof screws
• NEXUS® compatible
• Sealed maintenance-free Nickel Cadmium battery
Supply and install Emergi-Lite® Survive-All™ LPEX600-N
combination of unit equipment and Exit Sign series. The equipment
shall operate under two input voltage, 120VAC or 347VAC. The
equipment frame shall be of industrial grade polyvinyl chloride with a
gasket around lenses and canopy designed specifically for hostile
environments. The unit shall be certified for NEMA-4X for wall and
ceiling mount designed specially for high abuse areas, wet locations,
and cold weather (CW option). The faceplate(s) shall be constructed of
heavy-duty vandal-resistant polycarbonate and feature an even
illuminated legend. The legend light source shall be light emitting
diodes (LED). Red LED technology shall be ALINGAP. Emergency lights
shall be fully adjustable and high efficiency MR16 lamps. The
Emergi-Lite® Advanced Diagnostic Microcontroller board shall supply
the rated load for minimum of 1/2 hour to 87.5% of the rated battery
voltage. The unit shall be rated 120/347 V, 60 Hz and be CSA listed. The
unit shall have an output of
V
W. The battery charger shall
be driven by a micro-controller and shall include functions of Lockout,
Brownout Circuits, and Low Voltage Disconnection. It protects the unit
from over-current, short-circuit, and reverse polarity. The unit shall
self-test for 1 minute every 30 days, 10 minutes on the 6th month and
30 minutes every 12 months. The unit shall be capable of full recharge
in compliance with CSA specifications. The unit shall be furnished with
a magnetic test switch. A “Service Required” lamp shall be located near
the test switch and flash when a fault is detected. A four-LED diagnostic
display shall be located inside the equipment and shall identify the
source of failure: battery, charger circuitry, LED lamps or emergency
lights. The Exit Sign shall be listed CSA-C22.2 No. 141 and CSA-C860
approved.
The equipment shall be Emergi-Lite® Model:
.
• Meets or exceeds CSA 22.2 No. 141
NEMA-4X
DIMENSIONS
Dimensions are approximate and subject to change.
14” [35.7 cm]
37/8” [9.9 cm]
31/2” [8.7 cm]
91/4” [23.4 cm]
125/8” [32.1 cm]
131/4” [33.6 cm]
Note: double face models have double the power consumption above.
POWER CONSUMPTION
SURVIVE-ALL™ NEMA 4X & NSF CERTIFIED FAMILY
MODEL
LPEX60-N3
LPEX600 SERIES
ENC SERIES
NXM SERIES
EF39 & EF39P
LPEX60-N3CW
SERIES
P. 62
P. 63
P. 64
P.120-121
-
-
-
-
120/347VAC 0.15/0.05 A
0.25/0.08 A
36
30
20
15
8
36
30
20
15
8
0.27/0.09 A
60
40
30
24
12
WIRE GUARDS WITH HEADS
WIRE GUARDS WITHOUT HEADS
460.0079-E
460.0027-E
460.0028-E
-
LPEX60-N6A
P.148-149
30MIN 1H00 1H30 2H00 4H00
Less than
2W
Exit Sign Model
EN SERIES
WATTAGE CAPACITY
AC SPECS
460.0078-E
460.0060-E
Wall Mount
End Mount
Ceiling Mount
Wall Mount
End or Ceiling Mount
ORDERING INFORMATION
SERIES
LPEX60=
NEMA 4X
& NSF
Certified*
*Certified
for wall
& ceiling
mount only
FACES
HOUSING/FACE
COLOUR
2= s ingle WW= white/white
WB= white/black
face
ouble WA= white/
3= d
face
aluminum
BB= black/black
BA= black/
aluminum
GA= grey/
aluminum
GW= grey/white
GB= grey/black
VOLTAGE
POWERPACK
Blank= 120 to
347VAC
-2= 120/277VAC
-N3= 6
V-36W
-N6A= 1
2V-60W
OPTIONS
Blank= advanced diagnostics
non-audible (standard)
-G= green legend
U= advanced diagnostics audible
NEX= NEXUS® system interface*
NEXRF= wireless NEXUS® system
interface*
CW= cold weather (-40°C)**
*Consult your sales representative for
options available with the NEXUS® system.
**Available in LPEX602 only. Single face only.
EXAMPLE: LPEX602WW-N3CW/2MI
65
# OF
HEADS
HEAD STYLE AND
WATTAGE
LA= MR16 LED, 6V-4W
Blank= n
o
heads LG= M
R16 LED, 12V-4W
2= two heads LI= MR16 LED, 12V-5W
LJ= MR16 LED, 12V-6W
MI= MR16 halogen,
6V-6W
MJ= MR16 halogen,
6V-10W
MK= MR16 halogen,
12V-12W
Project/Location:
EH Series
Contractor:
Date:
Pictogram Sign
Hazardous Locations
Class I Division 2- compliant
FEATURES
•C
ompliant Class I Division 2, Groups A, B, C and D as per CSA C22.2
No.137-M1981
• Class I Zone 2 Groups IIA, IIB, IIC
•T
emperature Code T6 (maximum + 85°C (185°F)) as per Canadian
Electrical Code, Part I and CSA C22.2 No.137-M1981
• High-impact
thermoplastic frame with built-in gasket to secure
against liquid leaks
• Sealed, heavy-duty, vandal-resistant polycarbonate face plate(s)
•C
oncealed pilot light and test switch with magnetic action
• Long-life white LED light source
• Supplied
standard with two pictogram films per face, for direction
selection
• Meets or exceeds CSA 22.2 No.141-10 standard for pictogram Exit Signs
• Universal
AC input: two-wire 120 to 347VAC; standard DC input:
two-wire 6 to 24VDC
• Energy efficient – consumes less than 2.5W in AC or DC-remote mode
•S
elf-Powered models come standard with auto-diagnostic functions
and deliver two hours of back-up legend illumination
•S
uitable for cold-weather: -40°C (-40°F) for AC/DC and -20°C (-4°F)
for Self-Powered models (option: -CW)
AC-only
120 to 347VAC
AC/DC standard
120 to 347VAC
AC/Special DC
120 to 347VAC
Two-wire 120V
AC/DC
120VAC
Auto-diagnostic
120 / 347VAC
Less than
2.5W
Less than
2.5W
Less than
2.5W
Less than
2.5W
Less than
3.5W
DC SPECS
-
-
6 to 24VDC
36, 48, 120VDC
120VDC
Nickel-Cadmium
battery
Less than
1W
Less than
2.5 W
Less than
2.5 W
DIMENSIONS
Dimensions are approximate and subject to change.
43/8” [11 cm]
Min. two
hours
91/4” [23.4 cm]
CLASS I DIV 2 FAMILY
43/8” [11.1 cm]
AC SPECS
TYPICAL SPECIFICATIONS
Supply and install the Emergi-Lite® EH Series of pictogram Exit
Signs. The equipment shall be certified for Hazardous Locations:
Class I Division 2 Groups A, B, C and D with a temperature code
T6 (maximum 85ºC (185ºF)). The equipment frame shall be of
industrial grade polyvinyl chloride with a gasket around lenses
and canopy. The faceplate(s) shall be constructed of heavy-duty
vandal-resistant polycarbonate and feature an even illuminated
pictogram legend. Each face plate shall come standard with
two legend films for pictogram and direction selection. The light
source shall be long-life white light-emitting diodes (LED). The
pictogram Exit Sign shall operate with universal 2-wire AC input
voltage of 120 to 347VAC at less than 2.5W and universal 2-wire
DC input voltage from 6 to 24VDC at less than 1W for single
and double face signs. The Self-Powered model shall include
a concealed pilot light and magnet-sensitive test switch, shall
use a sealed Nickel-Cadmium battery of 2.4V nominal voltage
and shall stay illuminated during emergency operation for at
least two hours upon AC failure. The Self-Powered model shall
include auto-test functions: it shall execute automatic tests for 5
minutes every 30 days, 30 minutes every 60 days and two hours
annually. When a fault is detected, the bi-colour pilot light shall
turn from green to red and flash following a particular code. The
code description shall be visible on a label next to the pilot light to
identify the failure type: battery, charger circuitry, or LED lamps.
The pictogram Exit Sign shall meet or exceed the CSA 22.2
No.141-10 standard.
The equipment shall be Emergi-Lite® Model:
POWER CONSUMPTION
MODEL
Prepared by:
EHC SERIES
EXHZ SERIES
HZM SERIES
EF41 SERIES
P. 67
P. 68-69
P. 70-71
P.126-127
P.154
< PICTOGRAM
LEFT FROM HERE
PICTOGRAM
STRAIGHT FROM HERE
131/4” [33.6 cm]
LPEXHZ SERIES
21/4” [5.7 cm]
31/2” [8.9 cm]
PICTOGRAM >
RIGHT FROM HERE
ORDERING INFORMATION
SERIES
FACES*
EH= CL.I Div.2
pictogram
Exit Sign
1= single face
2= double
face
*Ceiling or wall
mount only.
HOUSING COLOUR
G= grey
VOLTAGE
ID= 120/ 347VAC; Self-Powered / 2 hours c/w non-audible diagnostic
ID2= 120/ 277VAC; Self-Powered / 2 hours c/w non-audible diagnostic
U= universal 120 to 347VAC; 6 to 24VDC
U00= 120 to 347VAC only
U36= 120 to 347VAC; 36VDC
U48= 120 to 347VAC; 48VDC
U120= 120 to 347VAC; 120VDC
EM120-2W= 2-wires 120VAC/VDC
EXAMPLE: EH1GU
66
OPTIONS
EXUS® system
NEX= N
interface*
NEXRF= wireless NEXUS®
system interface*
CW= cold weather
(-20°C for
Self-Powered, -40°C
for AC/DC)
*Note: some options are not
available with the NEXUS®
system.
.
Project/Location:
LPEXHZ Series
Contractor:
Hazardous Location
LED Exit Sign
Class I Division 2- compliant
Date:
Prepared by:
FEATURES
TYPICAL SPECIFICATIONS
• Certified Class I Zone 2, Groups IIA, IIB and IIC
•C
ertified Class I Division 2, Groups A, B, C and D as per
CSA C22.2 No.137-M1981
• Temperature
Code: T6 (maximum 85ºC as per Canadian
Electrical Code, Part I and CSA C22.2 No.137-M1981)
• CSA certified, meets or exceeds CSA 22.2 No. 141 requirements
• Input voltages: 120 to 347VAC universal AC input; 6 to 48VDC
universal DC input
•H
igh impact thermoplastic frame, with built-in gasket to
prevent water infiltration
•S
uited for areas with the risk of presence of flammable gases,
vapors or liquids able to create an explosive atmosphere
• Sealed faceplate of heavy-duty, vandal-resistant polycarbonate
• Tamper-resistant, hermetically sealed magnetic test switch
• Auto-diagnostic circuitry is standard on Self-Powered models
• Sealed, maintenance-free, Nickel-Cadmium batteries
• B
atteries recharge as per CSA requirements and provide 90
minutes of emergency operation
• Long-life, energy-efficient ALINGAP red LED light source
•E
nergy efficient – consumes less than 3W in AC or DC mode
• Comes standard with industrial-grade, Die-Cast aluminum
electrical box
•S
uitable for cold weather: -20°C (-4°F) (Self-Powered model,
“CW” option) and -40°C (-40°F) (AC only and AC-DC models)
Supply and install Emergi-Lite® LPEXHZ Series LED Exit Signs. The
equipment shall operate with universal two-wire AC input voltage from
120VAC to 347VAC at less than 3W and universal two-wire DC input
voltage from 6VDC to 48VDC at less than 2W for single and double face
signs. Designed specifically for hostile environments, the equipment
frame shall be of industrial grade high impact thermoplastic with a
gasket around lenses and canopy. The faceplate(s) shall be constructed
of heavy-duty vandal-resistant polycarbonate and feature an even
illuminated legend. The light source shall be light emitting diodes
(LED). Red LED technology shall be ALINGAP. An LED-sensitive
diffuser shall be mounted behind the legend to provide the 6” high
by 3/4” stroke letters with even illumination. The equipment shall be
certified for Hazardous Locations: Class I Division 2 Groups A, B, C and
D with a temperature code T6 Maximum 85ºC (185°F). The equipment
shall be designed specifically for high abuse areas, wet location, and
cold weather -20°C (-4°F) applications. The Self-Powered model shall
stay illuminated during emergency operation for at least 90 minutes
upon AC failure and shall include a magnetic test switch and
self-testing/self-diagnostic functions. The equipment shall automatically self test for 5 minutes every 30 days, 30 minutes every 60 days and
90 minutes annually. A “Service required” lamp shall be located near
the test switch and flash when a fault is detected. A two-LED diagnostic
display shall be located inside the equipment and shall identify the
eventual source of failure (battery, charger circuitry, or LED lamps).
The Exit Sign shall be CSA-C860 approved and meets CSA 22.2 No. 141.
The equipment shall be Emergi-Lite® Model:
POWER CONSUMPTION AND UNIT RATING
MODEL
AC SPECS
120 to
347VAC
120 to
347VAC
120 to
347VAC
Less than
3W
Less than
3W
Less than
3W
Self-Powered
green
120 to
347VAC
120VAC/VDC 2
wires, red
120VAC
AC/DC red
WIRE GUARDS
AC/DC green
460.0080-E
Wall Mount
Self-Powered red
DIMENSIONS
Dimensions are approximate and subject to change.
43/8” [11 cm]
91/8” [23.2 cm]
131/4” [33.6 cm]
ORDERING INFORMATION
FACES/MOUNTING
HOUSING/FACEPLATE COLOUR
LPEXHZ
2= single face, ceiling
or wall mount
3= double face, ceiling
mount only
GG= grey/grey
Less than 2W
6 to 48VDC
Less than 2W
Nickel-Cadmium
battery
Min. 90
minutes
Less than
3W
Nickel-Cadmium
battery
Min. 90
minutes
Less than
3W
120VDC
Less than 3W
CLASS I DIV 2 FAMILY
31/2” [8.8 cm]
SERIES
6 to 48VDC
Note: double face models have double the power consumption above.
131/2” [34.2 cm]
21/4” [5.7 cm]
DC SPECS
EH SERIES
EHC SERIES
EXHZ SERIES
HZM SERIES
EF41 SERIES
P. 66
P. 68-69
P. 70-71
P.126-127
P.154
VOLTAGE
OPTIONS
U= universal 120-347VAC, 6-48VDC
ID= 120-347VAC, Self-Powered c/w
non-audible diagnostics
EM120-2W= 120VAC, 120VDC, 2
wires (AC only)
Blank= red legend
-G= green legend
-CW= cold weather -20°C Self-Powered only
NEX= NEXUS® system interface*
NEXRF= wireless NEXUS® system interface*
EXAMPLE: LPEXHZ2GGU
67
*NEXUS® option with Self-Powered models only
Project/Location:
EHC Series
Contractor:
Pictogram Exit Combination Unit
Hazardous Locations
Class I Division 2- compliant
Date:
Prepared by:
TYPICAL SPECIFICATIONS
FEATURES
•C
ertified Class I Division 2, Groups A, B, C and D as per CSA
C22.2 No.137-M1981
Supply and install Emergi-Lite® EHC Series combination emergency
light battery unit and pictogram sign. Designed specifically for hazardous
locations, the equipment frame shall be of industrial grade polyvinyl
chloride with gaskets around both sides of the frame contour. The back
plate shall be made of 1/8” thick aluminum sheet and shall include
knock-outs for installation on an electrical box and four keyholes for alternative installation on a wall surface. The faceplate shall be constructed of
heavy-duty vandal-resistant clear polycarbonate and feature a uniformly
illuminated pictogram legend.
•C
ertified temperature Codes for several types of emergency
lamps
• Certified CSA C22.2 No.141-10
•P
olyvinyl chloride frame, with built-in gasket to prevent water
infiltration
•H
eavy-duty 1/8” thick aluminum back plate with keyholes for
wall-mount installation
The unit shall come standard with two legend films for pictogram and
direction selection. The light source shall be long-life white light-emitting diodes (LED). The unit shall have attached a lower compartment
containing two emergency heads with adjustable swivels and long-life
MR-16 LED lamps of ___ V and ___ W. The heads shall be installed on a
shield housing made of cast aluminum and protected by a shock-absorbent, clear polycarbonate cover. The standard AC input voltage shall be
120/347VAC. The equipment shall be equipped with a magnetic test switch
and one LED pilot light protected by the face plate.
• Sealed, vandal-resistant faceplate of polycarbonate
• Legend illuminated by long-life white LEDs
• Comes standard with two pictogram films for direction selection
•T
wo high-performance MR16 LED lamps shielded by a clear
polycarbonate cover
• 5 W LED emergency lights provide 60‘ of egress illumination on
a 6-foot wide path
The unit shall perform auto-test functions managed by a micro-controller
and shall automatically self-test for one minute every 30 days, 10 minutes
in the 6th month and 30 minutes annually. When a fault is detected, the
bi-color pilot light shall turn from green to red and flash following a
particular code. The code description shall be displayed on a label next
to the pilot light to identify the failure type: battery, charger circuitry, LED
lights for the signage, or emergency lights. The combination unit shall be
approved CSA C22.2 No.141-10 and No.137-M1981 for Class I Division 2
Groups A, B, C and D.
•L
ED emergency lights provide 30-36’ of egress illumination on a
6-foot wide path
•S
ealed, maintenance-free Lead-Calcium or Nickel-Cadmium
batteries
•R
emote load capacity: covers with LED lights 100 ft up to 230 ft of
egress illumination
• Comes standard with auto-diagnostic
•C
old-weather option: -40°C (-40°F) with only 14W extra power
consumption
The combination unit shall be Emergi-Lite® model:
.
TEMPERATURE CODES
CLASS I DIV 2 FAMILY
LPEXHZ SERIES
EXHZ SERIES
EH SERIES
HZM SERIES
EF41 SERIES
P. 67
P. 70-71
P. 66
P.126-127
P.154
LAMP
RATING
TEMPERATURE
CODE
MAX.
TEMPERATURE
REPLACEMENT
PART NUMBER
6V-10W
T3C
160°C (320°F)
580.0079
12V-12W
T3A
180°C (356°F)
580.0080
12V-20W
T2D
215°C (419°F)
580.0068
POWER CONSUMPTION
MODEL
AC SPECS
EMERGENCY POWER AVAILABLE FOR LAMPS
30MIN
1H00
1H30
2H00
4H00
Less than 2.5W
-
-
-
-
-
EHC-6L36
0.10/0.03 A
36
21
15
12
-
EHC-6L36-CW
0.25/0.08 A
36
21
15
12
-
0.10/0.03 A
36
30
20
16
8
EHC-6N36-CW
0.25/0.08 A
36
30
20
16
8
EHC-12N60
0.18/0.06 A
60
40
30
20
10
Pictogram Sign Module
EHC-6N36
120/347VAC
120/347VAC
68
Project/Location:
EHC Series
Contractor:
Pictogram Exit Combination Unit
Hazardous Locations
Class I Division 2- compliant
Date:
Prepared by:
DIMENSIONS
Dimensions are approximate and subject to change.
141/2” [36.8 cm]
31/2” [8.7 cm]
133/4” [34.9 cm]
61/4” [15.9 cm]
PICTO
STRAIGHT FROM HERE
125/8” [32.1 cm]
<PICTO
LEFT FROM HERE
PICTO>
RIGHT FROM HERE
ORDERING INFORMATION
SERIES
EHC= Class I
Zone 2
pictogram
combo
HOUSING
COLOUR
G= grey
BATTERY TYPE AND
POWER
6L36= 6V-36W
Lead-Calcium
6N36= 6V-36W
Nickel-Cadmium
12N60= 12V-60W
Nickel-Cadmium
HEAD STYLE AND WATTAGE
Blank= no heads
LA= MR16 LED, 6V-4W
LG= MR16 LED, 12V-4W
LI= MR16 LED, 12V-5W
MJ= MR16 halogen, 6V-10W
MK= MR16 halogen, 12V-12W
MW= MR16 high output, 12V-20W
OPTIONS
uto-diagnostics,
Blank= a
non-audible
-2= 120/277/VAC input
D1= time delay (5 minutes)
D2= time delay (10 minutes)
D3= time delay (15 minutes)
U= auto-diagnostics, audible
NEX= N
EXUS® system
interface*
NEXRF= wireless NEXUS®
system interface*
CW= cold weather -40°C
(only 6V units)
* Consult your sales
representative.
EXAMPLE: EHCG6N36LD1
69
Project/Location:
EXHZ Series
Contractor:
Combination Unit
Hazardous Location, Class I Zone 2
Date:
Prepared by:
TYPICAL SPECIFICATIONS
FEATURES
• Certified Class I Zone 2, Groups IIA, IIB and IIC
Supply and install Emergi-Lite® EXHZ Series combination
emergency light battery unit and LED Exit Sign. Designed
specifically for hostile environments, the equipment frame shall
be of industrial grade polymer with gaskets around both sides
of the frame contour. The back plate shall be made of 1/8” thick
aluminum sheet and shall include knockouts for installation on
an electrical box and four keyholes for alternative installation on
a wall surface. The faceplate shall be constructed of heavy-duty
vandal-resistant polycarbonate and feature a uniformly illuminated
legend. The light source shall be light emitting diodes (LED). Red
LED technology shall be ALINGAP. An LED-sensitive diffuser shall
be mounted behind the legend to provide the 6” high by 3/4” stroke
letters with even illumination. When specified, the equipment shall
have attached a lower compartment containing two emergency
lights with adjustable swivels and long-life MR-16 halogen lamps
of
V and
W. The lamps shall be shielded by cast
aluminum housing and protected by a shock-absorbent,
transparent polycarbonate cover. The equipment shall be certified
for Hazardous Locations: Class I Division 2 Groups A, B, C and D.
The standard AC input voltage shall be 120/347VAC. The equipment
shall be equipped with a magnetic test switch located behind the
face plate and two LED pilot lights: AC-on and “Service required”.
The unit shall include self-testing/self-diagnostic functions
monitored by a micro-controller and shall automatically self test
for one minute every 30 days, 10 minutes in the 6th month and 30
minutes annually. The “Service required” LED shall light when a
fault is detected. A four-LED diagnostic display located inside the
equipment shall identify the source of the failure (battery, charger
circuitry, or lamp load).
The Exit Sign module shall be CSA-C860 approved.
The combination unit shall be Emergi-Lite® Model:
.
• Certified
Class I Division 2, Groups A, B, C and D as per CSA C22.2
No.137-M1981
• Certified temperature Codes for several types of emergency lamps
• Certified CSA C22.2 No141
• Certified CSA C860
• Polymeric frame, with built-in gasket to prevent water infiltration
• Heavy-duty
1/8” thick aluminum back plate with keyholes for
secure wall-mount installation
• Sealed faceplate of heavy-duty, vandal-resistant polycarbonate
•S
uited for areas with the risk of flammable gases, vapors or liquids
that can create an explosive atmosphere
•E
xit Sign module illuminated by long-life, energy-efficient ALINGAP
red LEDs
•T
wo MR16 halogen lamps, shielded by a cast aluminum housing
and a polycarbonate cover
•S
ealed, maintenance-free, Lead-Calcium or Nickel-Cadmium
batteries
• Remote load capacity
• Comes standard with auto-diagnostic functions
• ½” electrical conduit entry on both sides and at the top
• NEXUS® compatible (for more information on NEXUS®, contact your
sales representative)
WIRE GUARDS
460.0078-E
Wall Mount
TEMPERATURE CODES
CLASS I DIV 2 FAMILY
ENC SERIES
EHC SERIES
EH SERIES
HZM SERIES
EF41 SERIES
P. 67
P. 68-69
P. 66
P.126-127
P.154
EXHZ-N3
EXHZ-L6A
EXHZ-H10A
120/347VAC
MAX.
TEMPERATURE
REPLACEMENT
PART NUMBER
6V-10W
T3C
160°C
580.0079
12V-12W
T3A
180°C
580.0080
12V-20W
T2D
215°C
580.0068
T4A
120°C
580.0097
T4A
120°C
580.0093
T4A
120°C
580.0104
WATTAGE CAPACITY
AC SPECS
EXHZ-L3
TEMPERATURE
CODE
6V-4W
LED
12V-4W
LED
12V-5W
LED
POWER CONSUMPTION
MODEL
LAMP
RATING
30MIN
1H00
1H30
2H00
4H00
0.15/0.06 A
36
21
15
12
-
0.15/0.06 A
36
30
20
15
-
0.30/0.10 A
60
40
30
20
10
0.30/0.10 A
100
72
40
36
18
70
Project/Location:
EXHZ Series
Contractor:
Combination Unit
Hazardous Location, Class I Zone 2
Date:
Prepared by:
DIMENSIONS
Dimensions are approximate and subject to change.
31/2” [8.7 cm]
141/2” [36.8 cm]
61/4” [15.9 cm]
125/8” [31.1 cm]
133/4” [34.9 cm]
ORDERING INFORMATION
SERIES
HOUSING
FACE
COLOUR
EXHZ= combo GG= grey/grey
Exit
Class I
Div. 2
VOLTAGE
CAPACITY
Blank=
N3= 6V- 36W
120/347VAC
Nickel-Cadmium
2=
N6A= 12V - 60W
Nickel-Cadmium
120/277VAC
H10A= 12V-100W NiMH
LEGEND
COLOUR
OPTIONS
Blank= red U= auto-diagnostics, audible
uto-diagnostics,
legend
UN= a
non-audible
G= green
NEX= NEXUS® wired system
legend
interface*
NEXRF= NEXUS® wireless
system interface*
*Consult your sales representative
for options with the NEXUS®
system.
EXAMPLE: EXHZGGN3U12MJ
71
NUMBER
OF HEADS
HEAD STYLE/
WATTAGE
MJ= MR16 halogen,
Blank= n
o
heads
6V-10W
/2= t wo
MK= MR16 halogen,
heads
12V-12W
MW= MR16 high
output, 12V-20W
LA= 6V-4W LED
LG= 12V-4W LED
LI= 12V-5W LED
Project/Location:
EX Series
Contractor:
Hazardous Location “Exit” Sign
TS Series Transfer Panel
Date:
Prepared by:
TYPICAL SPECIFICATIONS
FEATURES
Supply and install the Emergi-Lite® EX Series remote pictogram exit
signs. The lighting fixture shall have a die-cast aluminum body with
gray epoxy powder coat finish and a transparent glass globe. The
light source shall be long-life Light-Emitting Diodes (LED) in a lamp
assembly rated __V. The LED assembly shall emit white light and
shall consume less than 4W in AC or DC current. The legend housing
shall be of industrial-grade 14-gauge steel with gray enamel finish.
The face plate(s) shall consist of three layers: a white translucent
panel, a green/clear legend film and a clear Polycarbonate panel for
rigidity enforcement. Each face plate shall come standard with two
legend films per face, for direction selection.
• CSA Certified for use in hazardous locations:
- Class I, Division 1 and 2, Groups A, B, C, D
- Class II, Division 1 and 2, Groups E, F, G
- Class III, Divisions 1 and 2
• Very low Temperature Codes (see table)
• Listed CSA C22.2 No.137-M1981
• Listed CSA 22.2 No.141-10
•L
ighting fixture of die-cast aluminum with gray epoxy powder coat
finish
•L
egend housing of industrial-grade 14-gauge steel with gray
enamel finish
The equipment shall be certified CSA C22.2 No.137-M1981 for
Hazardous Locations: Class __, Division ___, Groups ______ with the
temperature code: _______.
•S
upplied standard with two pictogram films per face, for direction
selection
The equipment shall be certified CSA 22.2 No.141-10
• Long-life white LED light source
The equipment shall be Emergi-Lite® Model: __________________ .
• Two-wire AC/DC input available in 6, 12, 24 or 120V
• Energy efficient – consumes maximum 4.0W in AC and DC mode
POWER CONSUMPTION AND UNIT RATING
MODEL
AC SPECS
DC SPECS
6VAC
6VDC
12VAC
AC/DC
Maximum 4W
24VAC
120VAC
12VDC
24VDC
Maximum 4W
120VDC
*NOTE: Exit Signs of 6,12 or 24 V must be connected through transfer panels; maximum five Exit Signs per panel.
CERTIFICATION GUIDE FOR EX SERIES (40°C AMBIENT)
SEVERITY CODE
S1
S2
S3
S4
TEMPERATURE CODE
T6
T6
T4A
T6
CSA/UL RATING
Maximum 85o C
Maximum 85o C
Maximum 85o C
Maximum 85o C
*NOTE: Exit Signs of 6,12 or 24 V must be connected through transfer panels; maximum five Exit Signs per panel.
PRODUCT SELECTION GUIDE
ENVIRONMENT
SEVERITY CODE
Class I Div.1 Groups A, B
S1
Class I Div.1 Groups C, D
S2
Class I Div.2 Groups A, B, C, D
S3
Class II Div. 1 & 2 Groups E, F, G
Class III Div.1 and 2
S4
72
Project/Location:
EX Series
Contractor:
Date:
Hazardous Location “Exit” Sign
TS Series Transfer Panel
Prepared by:
DIMENSIONS
6” [15.5cm]
18 1/2” [47.0 cm]
9 5/8” [24.5 cm]
12 3/8” [31.1 cm]
17 3/8” [44.2 cm]
24 1/4” [61.5 cm]
14 1/8” [37.7 cm]
7 1/8” [18.1 cm]
5 1/4” [13.3 cm]
12 3/8” [31.4 cm]
12 3/8” [31.4 cm]
30 3/8” [77.1 cm]
10 7/8” [27.5 cm]
12 3/8” [31.4 cm]
12 3/4” [31.4 cm]
30 3/4” [78.0 cm]
13 3/8” [34.1 cm]
9 1/4” [23.5 cm]
10” [25.4 cm]
4 1/8” [10.4 cm]
SEVERITY S1, S2, S3 & S4
9” [22.9 cm]
NO SEVERITY RATING
8 3/8” [21.3 cm]
8 1/2” [21.5 cm]
3 3/8” [8.4 cm]
” [28.7 cm]
11
1/2
3 1/2” [9 cm]
12 3/8” [31.4 cm]
12 1/4 [31.2 cm]
2 1/2” [5.7 cm]
4” [10.1 cm]
19 3/4” [50 cm]
10 1/4” [27 cm]
3 3/8” [8.4 cm]
28 1/2” [72.3 cm]
8” [15.3 cm]
16 1/4” [41.2 cm]
SEVERITY S4
2. TRANSFER PANELS
33” [83.9cm]
S1 & S2
14 3/5” [15.5cm]
SEVERITY S1 & S2
8” [15.3 cm]
1. EX SERIES
5” [11.5cm]
Dimensions are approximate and subject to change.
< PICTO
LEFT FROM HERE
8” [20.3 cm]
PICTO
STRAIGHT FROM HERE
PICTO >
RIGHT FROM HERE
10 1/2” [25 cm]
ORDERING INFORMATION
1. EX SERIES
SERIES
EX= Hazardous Location
pictogram sign
NO. OF FACES
1= single face
2= double face, universal
mount
SEVERITY CODE
S1= Class I Div.1 Gr. A, B
S2= Class I Div.1 Gr. C, D
S3= Class I Div.2 Gr. A, B, C, D
S4= Class II Div.1&2 Gr. E, F, G
Class III Div.1&2
MOUNTING
C= Ceiling
P= Pendant
W= Wall*
* Wall-mount only available for
severities S2, S3 and S4
INPUT VOLTAGE
6= 6V AC/DC
12= 12V AC/DC
24= 24V AC/DC
120= 120V AC/DC
Unlike EXIT signs, the pictogram sign is not available in double arrow configuration.
EXAMPLE: EX1S1C6
2. TRANSFER PANELS - TS SERIES
AC VOLTAGE
120= 120VAC
347= 347VAC
DC VOLTAGE
-6= 6V
-12= 12V
-24= 24V
-120= 120V
SERIES
TS= Transfer Panel
LOAD POWER
25= 25W*
* 4W per pictogram sign
73
HOUSING
Blank= NEMA1
Project/Location:
LPEX-XP Series
Contractor:
Hazardous Location “Exit” Sign
TS Series Transfer Panels
FEATURES
Date:
Prepared by:
TYPICAL SPECIFICATIONS
LPEX-XP Series Remote Exit Signs
Supply and install the Emergi-Lite® LPEX-XP Series remote Exit Sign. The
exit housing shall be industrial grade 14-gauge steel and finished in grey
enamel. The faceplate will be constructed of heavy-duty 14-gauge steel
and feature universal knockout chevrons and the red letters shall not be
less than 6” in height with a 3/4” stroke. The sign shall come complete
with a
Volt LED lamp, and function from one voltage source only,
in AC and DC current. The LED Lamp shall use ALINGAP LEDs and shall
consume less than 5W in either AC or DC current.
• CSA Certified for use in hazardous locations:
- Class I, Divisions 1 and 2, Groups A, B, C, D
- Class II, Divisions 1 and 2, Groups E, F, G
- Class III, Divisions 1 and 2
• Die-Cast aluminum body with grey epoxy powder coat finish
• Exit housing and faceplate made of industrial-grade
14-gauge steel and finished in grey enamel
The Exit Sign shall be CSA-C860 approved and meets CSA 22.2 No. 141.
The Exit Sign shall be suitable for Class
Group
.
• Faceplate features universal knockout chevrons
• Two-wire input circuit for both AC and DC inputs
, Division
,
The Exit Sign shall be Emergi-Lite® Model:
• Available in 6, 12, 24 and 120VAC/DC
•L
ED lamp with ALINGAP LEDs; consumes less than 5W in AC
and DC mode
.
TS Series Transfer Switch:
Supply and install the Emergi-Lite® TS Series transfer switch for
hazardous location remote Exit Signs. The unit shall have two voltage
inputs:
VAC and
VDC and shall be able to maintain
an output of
V 25W for the permanent supply of a total of five
remote LED Exit Signs.
•N
ew, easy-to-build catalogue number based on the
Emergi-Lite® Severity Codes
• CSA certified, meets or exceeds CSA 22.2 No. 141 requirements
•A
lso available as Self-Powered Exit Sign, battery unit and
combo unit; see EXP catalogue sheet
The transfer switch shall be suitable for Class
,
Division
, Group
or for a NEMA 1 environment.
TS Series Transfer Switch
•A
vailable with explosion-proof housing (Class 1, Division 1) or
NEMA-1 housing (for use outside the hazardous location area)
The unit shall be Emergi-Lite® Model:
.
•S
tandard AC input: 120VAC, optional 277VAC, 347VAC; standard
DC input: 6, 12 or 24VDC
• Two-wire output with permanently present AC/DC low voltage
•O
utput power: 25W, can drive up to five (5) units of the LPEX-XP
remote exit series
POWER CONSUMPTION AND UNIT RATING
MODEL
AC SPECS
DC SPECS
6VAC
6VDC
12VAC
AC/DC red
two-wire
12VDC
Less than 5W
24VAC
Less than 5W
24VDC
120VAC
120VDC
*NOTE: Exit Signs of 6,12 or 24 V must be connected through transfer panels; maximum five Exit Signs per panel.
1.
2.
ENVIRONMENT
SEVERITY CODE
Cl. I, Div. 1, Gr. B
S1
Cl. I, Div. 1, Gr. C, D
S2
CI. I, Div. 2, Gr. B, C, D
S3
Cl. II, Div. 1 & 2, Gr. E, F, G
Cl. III, Div. 1 & 2
S4
CERTIFICATION GUIDE FOR LPEX-XP (40°C AMBIENT)
Severity Code
S1
S2
Temperature Code
T6
CSA/UL rating
74
Max. 85°C
(185°F)
S3
S4
T6
T3C
T3C (E.G.F.)
Max. 85°C
(185°F)
Max.
160°C
(320°F)
Max. 160°C
(320°F)
Project/Location:
LPEX-XP Series
Contractor:
Date:
Hazardous Location “Exit” Sign
TS Series Transfer Panels
Prepared by:
DIMENSIONS
Dimensions are approximate and subject to change.
PENDANT MOUNT
123/8” [31.4 cm]
81/2” [21.5 cm]
147/8” [37.7 cm]
95/8” [24.5 cm]
173/8” [44.2 cm]
241/4” [61.5 cm]
71/8” [18.1 cm]
147/8” [37.7 cm]
51/4” [13.3 cm]
83/8” [21.3 cm]
41/8” [10.4 cm]
CEILING MOUNT
TRANSFER SWITCH
HAZARDOUS
LOCATION
SEVERITY S1, S2, S3, S4
33” [83.9 cm]
DOUBLE PENDANT MOUNT
6” [15 cm] 6” [15 cm]
SEVERITY S1, S2, S3
123/8” [31.4 cm]
303/8” [77.1 cm]
NEMA-1
SEVERITY S3, S4
123/8” [31.4 cm]
303/4” [78 cm]
123/8” [31.4 cm]
91/4” [23.5 cm]
101/4” [26 cm]
10” [25.4 cm]
8” [20.3 cm]
281/2” [72.3 cm]
107/8” [27.5 cm]
31/2” [9 cm]
111/4” [28.7 cm]
123/8” [31.4 cm]
121/4” [31.2 cm]
21/4” [5.7 cm]
4” [10.1 cm]
193/4” [50 cm]
107/8” [27.5 cm]
WALL MOUNT
33/8” [8.4 cm]
CEILING MOUNT
31/8” [7.8 cm]
DOUBLE PENDANT MOUNT
6” [15 cm] 6” [15 cm]
PENDANT MOUNT
9” [22.9 cm]
133/8” [34.1 cm]
ORDERING INFORMATION
Before ordering, identify the environment of your application: Class
, Division
, Group
Refer to table 1 for the Severity Code to use in your catalogue number. For temperature information, please see table 2.
.
3. LPEX-XP
SERIES
MOUNTING
LPEXXP1= exit single face C860
LPEXXP2= exit double face C860 LED
C= ceiling
P= pendant
W= wall*
*Severity 2, 3 and 4 only
SEVERITY CODE
S1= CL.I, Div.1, Gr. A, B
S2= CL.I, Div.1, Gr. C, D
S3= CL.I, Div.2, Gr. A, B, C, D
S4= CL.II, Div.1, & 2 Gr.E, F, G
CL.III, Div.1 & 2
VOLTAGE
-EM6= 6V
-EM12= 12V
-EM24= 24V
-EM120= 120V
LAMP TYPE
Blank= LED less than 5W
EXAMPLE: LPEXXP1CSI-EM6
4. TRANSFER PANELS
AC VOLTAGE
120= 120VAC
347= 347VAC
DC VOLTAGE
-6= 6V
-12= 12V
-24= 24V
-120= 120V
SERIES
-TS= transfer switch
LOAD WATTAGE
-25= 25W*
*5W required per DC Exit load
EXAMPLE: 120-6-TS-25XP
75
HOUSING
Blank= NEMA 1
Project/Location:
C8SRXP Series
Contractor:
Date:
“Sortie” Sign and Transfer Panels
for Hazardous Locations
FEATURES
Prepared by:
TYPICAL SPECIFICATIONS
Remote Sortie Sign Series
Supply and install the Emergi-Lite® C8SRXP Series remote
“SORTIE” sign. The exit housing shall be industrial grade 14-gauge
steel and finished in grey enamel. The faceplate will be constructed
of heavy-duty
14-gauge steel and feature universal
knockout chevrons and the red letters shall not be less than 6” in
height with a 3/4” stroke. The sign shall come complete with a
Volt LED lamp, and function from one voltage source only, in
AC and DC current. The LED Lamp shall use ALINGAP LEDs and shall
consume less than 5W in either AC or DC current.
• CSA certified for use in hazardous locations:
- Class I, Divisions 1 and 2, Groups B, C, D
- Class II, Divisions 1 and 2, Groups E, F, G
- Class III, Divisions 1 and 2
• Die-Cast
aluminum body with grey epoxy powder coat finish
• Sortie Sign housing and faceplate made of 14-gauge steel, grey
enamel finish
The Sortie Sign shall be CSA-C860 approved and meets
CSA 22.2 No. 141.
• Faceplate features universal directional chevrons (knockouts)
• Two-wire circuit for both AC and DC inputs
The Sortie Sign shall be suitable for Class
, Group
.
• Available in 6, 12, 24 and 120VAC/DC
•L
ight source is ALINGAP LEDs; consumes less than 5W in AC or
DC mode
, Division
The Sortie Sign shall be Emergi-Lite® Model:
.
TS Series Transfer Switch:
•N
ew, easy-to-build catalog number based on the Emergi-Lite®
severity codes
Supply and install the Emergi-Lite® TS Series transfer switch for
hazardous location remote Exit Signs. The unit shall have two voltage
inputs:
VAC and
VDC and shall be able to
maintain an output of
V 25W for the permanent supply
of a total of five remote LED Exit Signs.
•C
SA certified, meets or exceeds CSA 22.2 No. 141
• Also available as Self-Powered Exit Sign, battery unit and combo
unit; see EXP catalogue sheet
Transfer Switch
The transfer switch shall be suitable for Class
,
Division
, Group
, or for a NEMA 1
environment.
•A
vailable with housing for hazardous locations
(Class 1, Division 1) or NEMA-1 housing (for use outside the
hazardous location area)
The unit shall be Emergi-Lite® Model:
• Standard AC input: 120VAC, optional: 277VAC, 347VAC
.
• Standard DC input: 6, 12 or 24VDC
• Two-wire output with permanently present AC/DC low voltage
•O
utput power: 25W, can drive up to five (5) remote units Series
C8SRXP
POWER CONSUMPTION AND UNIT RATING
MODEL
AC SPECS
DC SPECS
6VAC
6VDC
12VAC
AC/DC red
two-wire
Less than 5W
24VAC
120VAC
12VDC
Less than 5W
24VDC
120VDC
*NOTE: SORTIE signs of 6,12 or 24 V must be connected through transfer switch; maximum five signs per panel.
2.
1.
ENVIRONMENT
CERTIFICATION GUIDE FOR C8SRXP (40°C AMBIENT)
SEVERITY CODE
Cl. I, Div. 1, Gr. B
S1
Severity Code
Cl. I, Div. 1, Gr. C, D
S2
Temperature Code
T6
T6
T3C
CI. I, Div. 2, Gr. B, C, D
S3
T3C
(E.G.F.)
Cl. II, Div. 1 & 2, Gr. E, F, G Cl. III,
Div. 1 & 2
S4
CSA/UL rating
Max. 85°C
(185°F)
Max. 85°C
(185°F)
Max.
160°C
(320°F)
Max.
160°C
(320°F)
76
S1
S2
S3
S4
Project/Location:
C8SRXP Series
Contractor:
Date:
“Sortie” Sign and Transfer Panels
for Hazardous Locations
Prepared by:
DIMENSIONS
Dimensions are approximate and subject to change.
18” [45.7 cm]
81/2” [21.5 cm]
6” [15.3 cm]
33” [83.9 cm]
105/8” [26.9 cm]
173/8” [44.2 cm]
18” [45.7 cm]
6” [15.3 cm]
83/8” [21.3 cm]
41/8” [10.4 cm]
18” [45.7 cm]
95/8” [24.5 cm]
241/4” [61.5 cm]
147/8” [37.7 cm]
71/8” [18.1 cm]
51/4” [13.3 cm]
161/8” [41.1 cm]
CEILING MOUNT
TRANSFER SWITCH
HAZARDOUS
LOCATION
SEVERITY S1, S2, S3, S4
PENDANT MOUNT
183/8” [46.6 cm]
DOUBLE PENDANT MOUNT
123/8” [31.4 cm]
WALL MOUNT
(ONLY SEVERITY S2)
147/8” [37.7 cm]
SEVERITY S1, S2
42” [106.8 cm]
SEVERITY S3, S4
PENDANT MOUNT
18” [45.7 cm]
9” [22.9 cm]
101/4” [26 cm]
8” [20.3 cm]
91/4” [23.5 cm]
281/2” [72.3 cm]
6” [15.3 cm]
107/8” [27.5 cm]
12 ” [31.2 cm]
6” [15.3 cm]
1/4
41/2” [11.5 cm]
31/2” [9 cm]
4 ” [10.4 cm]
11 ” [28.7 cm]
18” [45.7 cm]
4” [10.2 cm]
1/8
1/4
195/8” [49.9 cm]
3” [7.7 cm]
CEILING MOUNT
103/4” [27.4 cm]
DOUBLE PENDANT MOUNT
123/8” [31.4 cm]
7/8
WALL MOUNT
” [2.1 cm]
NEMA-1
10” [25.4 cm]
42” [106.8 cm]
ORDERING INFORMATION
Before ordering, identify the environment of your application: Class
, Division
, Group
Refer to table 1 for the Severity Code to use in your catalogue number. For temperature information, please see table 2.
.
3. C8SRXP
SERIES
SEVERITY CODE
C8SRXP1= sortie single face
C8SRXP2= sortie double face
S1= CL.I, Div.1&2, Gr. B
S2= CL.I, Div.1&2, Gr. C, D
S3= CL.I, Div.2, Gr. B, C, D
S4= CL.II, Div.1, & 2 Gr.E, F, G CL.III, Div.1 & 2
MOUNTING
C= ceiling
P= pendant
W= wall*
VOLTAGE
*Note: wall mount available only for
severities S2, S3 and S4
6= 6V
12= 12V
24= 24V
120= 120V
EXAMPLE: C8SRXP1S1C6
4. TRANSFER PANELS
AC VOLTAGE
120= 120VAC
347= 347VAC
DC VOLTAGE
-6= 6V
-12= 12V
-24= 24V
-120= 24V
SERIES
-TS= transfer switch
LOAD WATTAGE
-25= 25W*
*5W required per DC “Sortie” load
EXAMPLE: 120-6-TS-25XP
77
HOUSING
Blank= NEMA 1
Project/Location:
EXP Series
Contractor:
Battery Units,
Self-Powered Exit Signs
Combination Units
Date:
Prepared by:
TYPICAL SPECIFICATIONS
CSA certified for use in hazardous locations
The EXP Series of battery equipment is designed to cover emergency
lighting applications for the entire spectrum of hazardous locations,
where inflammable gases, vapors, liquids, dust particles, fabrics or
tissues are permanently present or are likely to exist.
In one simple-to-order catalogue family the EXP Series combines
three traditional emergency lighting products with battery back-up:
battery units with emergency lights, Self-Powered Exit Signs, and
combination units with emergency lights and Exit Sign. The equipment
is also available with additional emergency power capacity to drive
remote heads and Exit Signs.
Supply and install the Emergi-Lite® EXP Series of hazardous location
battery unit equipment. The battery unit housing will be constructed
of Die-Cast aluminum with grey epoxy powder coat finish. The
equipment shall be rated for 120, 277 or 347V, 60 Hz input and be
CSA listed. The equipment shall have an output of
V
and
W and shall supply the rated load for minimum of
1/2 hour to 87.5% of the rated battery voltage. The battery shall be a
long-life, maintenance-free Lead-Calcium type. The charger shall be
fully computer tested and have its charge voltage set in the factory
to ± 1% tolerance. The charger shall be current limited, temperature
compensated, short circuit proof and reverse polarity protected. The
charger shall be furnished with an electronic lockout circuit, which
will connect the battery when the AC circuit is activated, and an
electronic brownout circuit, which will activate the emergency heads
when the utility power dips below 75% of nominal voltage.
Where required the equipment shall come complete with
heads, each of them equipped with
lamp(s) of
W. The head housing shall be Die-Cast aluminum with
grey epoxy powder coat finish. The lenses shall be a clear, impact and
heat resistant prismatic glass globe. The head shall be factory sealed,
with no need for external seals. Where required the equipment shall
come complete with one Exit Sign and will include a transfer circuit
to maintain the Exit Sign permanently lighting in both normal and
emergency operation. The exit housing shall be industrial grade
14-gauge steel and finished in grey enamel. The faceplate will be
constructed of heavy-duty 14-gauge steel and feature universal
knockout chevrons and the red letters shall not be less than 6” in
height with a 3/4” stroke. The sign shall include an LED lamp with
ALINGAP LEDs and shall consume less than 5W in either AC or
battery mode.
FEATURES
• CSA Certified for use in hazardous locations:
- Class I, Divisions 1 and 2, Groups B, C, D*
- Class II, Divisions 1 and 2, Groups E, F, G
- Class III, Divisions 1 and 2
• D
ie-Cast aluminum body with grey epoxy powder coat finish;
clear, impact and heat resistant prismatic glass globe
• Long-life, maintenance-free Lead-Calcium battery
• Battery charger is current limited, temperature compensated,
short-circuit proof and reverse polarity protected
• Emergency heads with one or twin lamp design
• Self-Powered exit (combo) includes a transfer circuit to drive four
remote LED-based remote Exit Signs
• Exit Sign uses an LED lamp with ALINGAP LEDs
• Exit Sign is CSA certified, meets or exceeds C860
• The Self-Powered version is also CSA C22.2 No. 141 certified
The equipment shall be suitable for Class
, Division
. The Exit Sign shall be CSA-C860 approved.
, Group
The equipment shall be Emergi-Lite® Model:
.
POWER CONSUMPTION AND UNIT RATING
MODEL
06EXP36
06EXP72
06EXP108
12EXP72
12EXP144
12EXP200
24EXP144
24EXP288
WATTAGE CAPACITY
AC SPECS
120/347VAC
0.50/0.20 A
0.50/0.20 A
0.50/0.20 A
0.50/0.20 A
0.50/0.20 A
0.50/0.20 A
0.50/0.20 A
0.50/0.20 A
30MIN
1H00
1H30
2H00
4H00
36
72
108
72
144
200
144
288
21
42
63
42
84
117
84
168
15
30
45
30
60
83
60
120
12
24
36
24
48
67
48
96
6
12
18
12
24
33
24
48
NOTE: The wattage capacity applies only to the battery unit. For combo or Self-Powered Exit Signs one must allocate 5W of emergency power for each sign.
1.
2.
ENVIRONMENT
SEVERITY CODE
Cl. I, Div. 1, Gr. B
S1
Cl. I, Div. 1, Gr. C, D
S2
CI. I, Div. 2, Gr. B, C, D
S3
Cl. II, Div. 1 & 2, Gr. E, F, G / Cl. III,
Div. 1 & 2
S4
CERTIFICATION GUIDE FOR EXP (40°C AMBIENT)
Severity Code
Temperature Code
CSA/UL rating
S1
T6
Max. 85°C
(185°F)
NOTE: Units for Class I Group A available without test switch and pilot light allocate 5W of emergency power. Contact your sales representative.
78
S2
S3
T6
T3C
Max. 85°C
(185°F)
Max.
160°C
(320°F)
S4
T3C
(E.G.F.)
Max.
160°C
(320°F)
Project/Location:
EXP Series
Contractor:
Battery Units,
Self-Powered Exit Signs
Combination Units
Date:
Prepared by:
DIMENSIONS
Dimensions are approximate and subject to change.
SMALL CABINET (36-72W)
63/8” [16.3 cm]
227/8” [58.2 cm]
195/8” [50 cm]
227/8” [58.2 cm]
195/8” [50 cm]
95/8” [24.4 cm]
103/8” [26.4 cm]
181/4” [46.5 cm]
207/8” [53 cm]
273/4” [70.5 cm]
143/8” [36.6 cm]
LARGE CABINET (108-288W)
81/4” [20.8 cm]
233/8” [59.2 cm]
201/8” [51 cm]
233/8” [59.2 cm]
201/8” [51 cm]
10” [25.4 cm]
131/8” [33.3 cm]
211/4” [53.9 cm]
305/8” [77.8 cm]
233/4” [60.4 cm]
143/8” [36.6 cm]
ORDERING INFORMATION
Before ordering, identify the environment of your application: Class
, Division
, Group
.
Refer to table 1 for the Severity Code to use in your catalogue number. For temperature information, please see table 2.
3. EXP
DC
VOLTAGE
06= 6V
SERIES
EXP
CAPACITY
CABINET
SIZE
36= 36W
72= 72W
108= 108W
12= 12V
72= 72W
144= 144W
200= 200W
24= 24V
144= 144W
288= 288W
AC
VOLTAGE
Blank=
120VAC
-2= 277VAC
-3= 347VAC
OPTIONS
Blank= no options
D= time delay
(15 minutes)
E1= single face Exit
Sign, LED
E2= double face Exit
Sign, LED
TS= transfer switch
HEAD STYLE AND
WATTAGE
Blank= no heads
/11= single remote,
1 lamp
/12= single remote,
2 lamps
/21= double remote,
1 lamp
SEVERITY CODE*
S1= CL.I, Div.1, Gr. A, B
S2= CL.I, Div.1, Gr. C, D
S3= CL.I, Div.2, Gr. A, B, C, D
S4= CL.II, Div.1, & 2 Gr.E, F, G
CL.III, Div.1 & 2
*For temperature codes, consult
your sales representative.
EXAMPLE: 06EXP36E1/21S312
79
LAMPS
12W= halogen, 6V, 12V,
12W, quartz bi-pin
20W= halogen, 12V, 24V,
20W, quartz bi-pin
Project/Location:
EXP Series
Contractor:
Battery Units,
Self-Powered “Sortie” Signs
Combination Units
CSA certified for use in hazardous locations
The EXP Series of battery equipment is designed to cover emergency
lighting applications for the entire spectrum of hazardous locations,
where inflammable gases, vapors, liquids, dust particles, fabrics or
tissues are permanently present or are likely to exist.
In one simple-to-order catalogue family the EXP Series combines
three traditional emergency lighting products with battery back-up:
battery units with emergency lights, Self-Powered Sortie Signs,
and combination units with emergency lights and Sortie Sign.
The equipment is also available with additional emergency power
capacity to drive remote heads and Sortie Signs.
FEATURES
• CSA Certified for use in hazardous locations:
- Class I, Divisions 1 and 2, Groups A, B, C, D*
- Class II, Divisions 1 and 2, Groups E, F, G
- Class III, Divisions 1 and 2
• D
ie-Cast aluminum body with grey epoxy powder coat finish;
clear, impact and heat resistant prismatic glass globe
• Long life, maintenance-free, Lead-Calcium battery; charger is
current limited, temperature compensated, short-circuit proof
and reverse polarity protected
• Emergency heads with one or twin lamp design
• Sortie Sign is CSA C860 certified
• Self-Powered exit (combo) includes a transfer circuit to drive four
LED-based remote Exit Signs
• Sortie Sign uses a LED lamp with ALINGAP LEDs
• The Self-Powered version is also CSA C22.2 No. 141 certified
Date:
Prepared by:
TYPICAL SPECIFICATIONS
Supply and install the Emergi-Lite® EXP Series of hazardous location
battery unit equipment. The battery unit housing will be constructed of
Die-Cast aluminum with grey epoxy powder coat finish. The equipment
shall be rated for 120, 277 or 347V, 60 Hz input and be CSA listed. The
equipment shall have an output of
V and
W
and shall supply the rated load for a minimum of 1/2 hour to 87.5% of
the rated battery voltage. The battery shall be a long-life,
maintenance-free Lead-Calcium type. The charger shall be fully
computer tested and have its charge voltage set in the factory to ± 1%
tolerance. The charger shall be current limited, temperature
compensated, short circuit proof and reverse polarity protected. The
charger shall be furnished with an electronic lockout circuit, which will
connect the battery when the AC circuit is activated, and an electronic
brownout circuit, which will activate the emergency heads when the
utility power dips below 75% of nominal voltage.
Where required the equipment shall come complete with
heads, each of them equipped with
lamp(s) of
W. The head housing shall be Die-Cast aluminum with grey epoxy
powder coat finish. The lenses shall be a clear, impact and heat
resistant prismatic glass globe. The head shall be factory sealed, with
no need for external seals.
Where required the equipment shall come complete with one Exit Sign
and will include a transfer circuit to maintain the Exit Sign permanently
lighting in both normal and emergency operation. The exit housing
shall be industrial grade 14-gauge steel and finished in grey enamel.
The faceplate will be constructed of heavy-duty 14-gauge steel and
feature universal knockout chevrons and the red letters shall not be
less than 6” in height with a 3/4” stroke. The sign shall include an LED
lamp with ALINGAP LEDs and shall consume less than 5W in either AC
or battery mode.
The equipment shall be suitable for Class
, Division
The Exit Sign shall be CSA-C860 and approved.
The equipment shall be Emergi-Lite® Model:
, Group
.
POWER CONSUMPTION AND UNIT RATING
MODEL
WATTAGE CAPACITY
AC SPECS
1H30
2H00
06EXP36
0.50/0.20 A
36
21
15
12
6
06EXP72
0.50/0.20 A
72
42
30
24
12
06EXP108
0.50/0.20 A
108
63
45
36
18
12EXP72
0.50/0.20 A
72
42
30
24
12
12EXP144
120/347VAC
30MIN
1H00
4H00
0.50/0.20 A
144
84
60
48
24
12EXP200
0.50/0.20 A
200
117
83
67
33
24EXP144
0.50/0.20 A
144
84
60
48
24
24EXP288
0.50/0.20 A
288
168
120
96
48
1.
2.
ENVIRONMENT
SEVERITY CODE
Cl. I, Div. 1, Gr. A, B
S1
Cl. I, Div. 1, Gr. C, D
S2
CI. I, Div. 2, Gr. A, B, C, D
S3
Cl. II, Div. 1 & 2, Gr. E, F, G / Cl. III,
Div. 1 & 2
S4
CERTIFICATION GUIDE FOR EXP (40°C AMBIENT)
Severity Code
S1
S3
S4
Temperature Code
T6
T6
T3C
T3C
(E.G.F.)
CSA/UL rating
Max. 85°C
Max. 85°C
Max.
160°C
Max.
160°C
NOTE: Units for Class I Group A available without test switch and pilot light allocate 5W of emergency power. Contact your sales representative.
80
S2
Project/Location:
EXP Series
Contractor:
Battery Units,
Self-Powered “Sortie” Signs
Combination Units
Date:
Prepared by:
DIMENSIONS
Dimensions are approximate and subject to change.
SMALL CABINET (36-72W)
103/8” [26.4 cm]
171/8” [43.6 cm]
221/2” [57.3 cm]
227/8” [58.2 cm]
195/8” [50 cm]
227/8” [58.2 cm]
195/8” [50 cm]
95/8” [24.4 cm]
61/8” [15.7 cm]
291/2” [70.5 cm]
143/8” [36.6 cm]
LARGE CABINET (108-288W)
131/8” [33.3 cm]
331/2” [84.9 cm]
265/8” [67.6 cm]
211/4” [53.9 cm]
233/8” [59.2 cm]
201/8” [51 cm]
233/8” [59.2 cm]
201/8” [51 cm]
10” [25.4 cm]
81/4” [20.8 cm]
143/8” [36.6 cm]
ORDERING INFORMATION
Before ordering, identify the environment of your application: Class
,Division
,Group
.
Refer to table 1 for the Severity Code to use in your catalogue number. For temperature information, please see table 2.
3. EXP
VOLTAGE
6= 6V
SERIES
EXP
CAPACITY
CABINET
SIZE
36= 36W
72= 72W
108= 108W
12= 12V
72= 72W
144= 144W
200= 200W
24= 24V
144= 144W
288= 288W
AC
VOLTAGE
Blank=
120VAC
-2= 277VAC
-3= 347VAC
OPTIONS
Blank= no options
D= time delay
(15 minutes)
S1= SORTIE single
face, LED
S2= SORTIE double
face, LED
TS= transfer switch
HEAD STYLE AND
WATTAGE
Blank= no heads
/11= single remote, 1
lamp
/12= single remote, 2
lamps
/21= double remote,
1 lamp
SEVERITY CODE
S1= CL.I, Div.1, Gr. A, B
S2= CL.I, Div.1, Gr. C, D
S3= CL.I, Div.2, Gr. A, B, C, D
S4= CL.II, Div.1, & 2 Gr.E, F, G
CL.III, Div.1 & 2
*For temperature codes, consult
your sales representative.
EXAMPLE: 06EXP36S112
81
LAMPS
12= halogen, 6V, 12V,
12W quartz bi-pin
20= halogen, 12V, 24V,
20W, quartz bi-pin
Project/Location:
ET Series
Contractor:
Date:
Power-Free “Exit”, “Sortie” or
Pictogram Sign
FEATURES
Prepared by:
TYPICAL SPECIFICATIONS
• Illumination provided by borosilicate glass tubes, internally
coated with zinc sulphide phosphor and filled with tritium gas
• Minimum brightness at time of manufacture is 0.132 footlambert (0.452 cd/m2)
• Decorative, slim-line heavy-duty ABS housing
• Rugged, impact-resistant polycarbonate face
• Spark-free construction
• Simple installation – universal direction capability, comes
complete with universal mounting hardware
• Stands up to extreme temperatures in outdoor or indoor
applications
• Life expectancy of 10 or 20-year (EXIT), 12-year (SORTIE) and
10-year (PICTOGRAM)
• Available in single or double face
• ISO 9001 Certified for Pictogram Sign
• Pictogram Sign includes universal stencils (straight from here,
left from here and right from here)
Supply and install Emergi-Lite® EX160 (EXIT) or SR160 (SORTIE) or ET
(PICTOGRAM) Series Self-Luminous Exit Signs. The Exit Sign shall be
constructed of a thermoplastic housing and be corrosion proof. The
sealed housing will incorporate no loose or removable parts allowing
for easy installation. The standard minimum guaranteed life will be 10
years. The standard mounting brackets will allow for either end/ceiling
or wall mount. Standard “Exit” and “Sortie” Signs shall be supplied
with white letters that are 6” high by 3/4” stroke. The initial average
minimum brightness shall be 0.132 foot-lambert (0.452 cd/m2).
The equipment shall be Emergi-Lite® Model:
.
WIRE GUARDS
460.0079-E
Wall Mount
460.0027-E
End Mount
460.0028-E
Ceiling Mount
DIMENSIONS
Dimensions are approximate and subject to change.
12-7/8”
[32.612.38”
cm] [32.58cm]1” [2.5 cm]
15.5”
[39.37cm]
1” [2.5cm]
12.38”
[32.58cm]
ORDERING INFORMATION: EXIT OR SORTIE SIGN
BACKGROUND
COLOURS
SERIES
EX162= EXIT sign, single face, universal
mount and chevrons
EX163= EXIT sign, double face, universal
mount and chevrons
SR162= SORTIE sign, single face, universal
mount and chevrons
SR163= SORTIE sign, double face, universal
mount and chevrons
HOUSING
COLOURS
LIFE YEARS
Blank= red
G= green*
G= grey*
W= white*
B= black
* Not available in Sortie
* Not available in Sortie
OPTIONS
-10= 10 years (EXIT only)
-12= 12 years
(SORTIE only)
-20= 20 years
(EXIT only)*
-AF = aluminum frame*
-PC = Polycarbonate shield*
-VR = Vandal cover*
NEW
-N
* Per face.
* Per face.
EXAMPLE: EX162W-10-AF-N
ORDERING INFORMATION: PICTOGRAM SIGN
SERIES
ET= Pictogram Sign
FACES
1 = single face universal
mount and chevrons
2 = double face universal
mount and chevrons
HOUSING COLOURS
W= white
B= black
G= grey
LIFE YEARS
OPTIONS
10= 10 years*
AF = aluminum frame*
PC = Polycarbonate shield*
VR = Vandal cover*
* Standard
* Per face.
Unlike Exit or Sortie, the Pictogram Sign is not available in double arrow configuration.
EXAMPLE: ET1W10AF
82
12
8.35 [21.21cm]
8.35 [21.21cm]
8.35 [21.21cm]
8.56 [21.74cm]
1” [2.5cm]
1” [2.5 cm]
8-1/4”
[21 cm]
8.35
[21.21cm]
8.56 [21.74cm]
8.56
[21.74cm]
8-1/2”
[21.7 cm]
14” [35.5
cm]
15.5” [39.37cm]
12.38”
[32.58cm]
8-1/4”
[21 cm]
8.35
[21.21cm]
[2.5 cm]
1”1”[2.5cm]
15-1/2”
[39.4 cm]
15.5”
[39.37cm]
Project/Location:
Contractor:
Special Wording
Date:
Prepared by:
Illuminated Signage
FEATURES
TYPICAL SPECIFICATIONS
•T
he same sturdy construction and electrical design used in our
Exit Signs is used to produce our custom-worded, illuminated
signage
Custom-worded, illuminated signage is available using the same
sturdy construction and electrical design as Emergi-Lite® Exit
Signage.
•S
ign bodies - steel, extruded and Die-Cast aluminum, weatherproof,
flame-retardant polycarbonate, high impact thermoplastic,
recessed housing
A wide range of sign body options and colour choices are available to
suit any application.
Contact your local Emergi-Lite® sales representative to discuss your
specific requirements.
•A
lso available with Self-Powered canopy and with emergency
lamps
•C
ustom wording – any style of lettering, any language, any
alphabet, any special characters
• Graphics – logos, standard symbols, custom art
• Colour choices – sign bodies, message, faceplate panel
• Illumination – LED (light-emitting diodes) – other light sources
available - consult representative
• White-out, black-out and split picture options
WHITE-OUT OPTION
NON-ILLUMINATED
BLACK-OUT OPTION
ILLUMINATED
NON-ILLUMINATED
When the sign is non-illuminated the acrylic panel in the faceplate appears
blank white. The message appears only when the sign is illuminated.
ILLUMINATED
When the sign is non-illuminated the acrylic panel in the faceplate appears
black. The message appears only when the sign is illuminated.
83
Project/Location:
Contractor:
LED Retrofit Kits
Date:
Prepared by:
Convert high-consumption incandescent and
fluorescent lamps to energy-efficient LED lamps
Converting existing Exit Signage from incandescent or fluorescent
lamps to LED (light emitting diodes) lamps drastically reduces
operating and maintenance costs for building owners and property
managers. As part of energy-efficiency programs, some Canadian
electric utilities are also actively promoting conversion to LED with
incentive and rebate programs for installers and building owners/
managers.
FEATURES
Emergi-Lite® offers four retrofit kit options; all
based on the long-life ALINGAP LED technology:
SNAP II SERIES
• Quick and easy to install
• SNAP II Series
• Long-life, energy-efficient red ALINGAP LED technology
• SNAP III Series
•M
odule features two independent circuits – one for AC input; one
for DC input
• SNAP I Series
• Bulb Series
•U
niversal AC input: 120/277/347VAC; universal two-wire DC input: 6 to
24VDC
Benefits of using LED lamps in Exit Signs:
•E
xceptional energy-efficiency – reduces energy consumption by up
to 90%
• Power consumption of 1.1W per module
• 10 year limited warranty
• Extremely long life – 10 to 25 years
DIMENSIONS
• Important reduction in maintenance and energy costs
Dimensions are approximate and subject to change.
• Average payback is less than two years (see page 6)
• Retrofit kits are easy to install
• Improved visibility and reliability: ALINGAP LED technology
1/8
11
13/16” [2.1
cm]
cm]
8.3
” [2
13/16” [3 cm]
POWER CONSUMPTION
MODEL
SNAP II
AC SPECS
120/277/347VAC
DC SPECS
1.1W
6 to 24VDC
1.3W
ORDERING INFORMATION
SERIES
SNAP II= hardwire retrofit kit 11.0”
(28cm) long
SNAP IIB= hardwire retrofit kit 9.5”
(24cm) long*
*Available in UN voltage only.
EXAMPLE: SNAPII-UN
84
VOLTAGE
-UN= 120/277/347VAC, 6/12/24VDC
-U36= 120/277/347VAC, 36VDC
-U48= 120/277/347VAC, 48VDC
-U120= 120/347VAC, 120VDC
-120V-1H2= 120VAC,120VDC, 2 wires
Project/Location:
Contractor:
LED Retrofit Kits
Date:
Prepared by:
New Design:
0.65W; 60% off power consumption.
SNAP III SERIES
SNAP I SERIES
• E asiest to install in its class
• Easiest to install in its class
• C ompact size makes it ideal for virtually all Exit Signs
• Compact size makes it ideal for virtually all Exit Signs
• C an be retrofitted directly on fluorescent ballast
• Can be retrofitted directly on fluorescent ballast
• L ong-life, energy-efficient red ALINGAP LED technology
•S
uitable for all AC line applications including Exit Signs equipped
with in-line diodes
• Available with AC adaptor for all types of lamp sockets
• Long-life, energy-efficient ALINGAP LED techonology
• 10 year limited warranty
DIMENSIONS
DIMENSIONS
Dimensions are approximate and subject to change.
Dimensions are approximate and subject to change.
]
1 cm
[24.
9 ”
cm]
4.1
/2 [2
91 ”
” [2.1 cm]
13/16
1/2
” [2.1 cm]
13/16
13/16” [3 cm]
13/16” [3 cm]
POWER CONSUMPTION
MODEL
SNAP III
AC SPECS
POWER CONSUMPTION
DC SPECS
120VAC; 86VAC step down from
347VAC
0.65W
N/A
MODEL
N/A
SNAP I
ORDERING INFORMATION
SERIES
SNAP III= for standard applications
AC SPECS
120VAC; 120VAC with in-line
diodes
DC SPECS
2.8W
N/A
ORDERING INFORMATION
BASE
SERIES
-C= candelabra
-I= intermediate
-M= medium
-B= bayonet
-F= G23 compact fluorescent
-UN= complete set of bases
(excludes “F” base)
-H= 120VAC (hardwire)
-2H= 277VAC (hardwire)
-3H= 347VAC (hardwire)
SNAP I = with or
without
in-line
diodes
EXAMPLE: SNAPIII-C
EXAMPLE: SNAPI-C
85
BASE
-C= candelabra
-I= intermediate
-M= medium
-B= bayonet
-F= G23 compact fluorescent
-UN= complete set of bases (excludes “F” base)
-H= 120VAC (hardwire)
-2H= 277VAC (hardwire)
-3H= 347VAC (hardwire)
N/A
Project/Location:
Contractor:
LED Retrofit Kits
Date:
Prepared by:
TYPICAL SPECIFICATIONS
The following is an example of the savings you can generate by
simply installing an LED retrofit kit in an existing incandescent Exit
Sign.
The Retrofit Kit Cost:
Installation cost (per unit) for a
retrofit kit (Labour):
Wattage rating per incandescent lamp in
existing fixture:
BULB SERIES
Number of incandescent lamps per
fixture:
• Quick and easy to install
•A
vailable with a wide range of lamp bases for quick lamp to lamp
replacement
• Long-life, energy-efficient ALINGAP LED techonology
• 120VAC or 120VAC with in-line diode
DIMENSIONS
Dimensions are approximate and subject to change.
11/4” [3.2 cm]
” [2.5 cm]
33/4” [9.6 cm]
” [2.1 cm]
” [2.1 cm]
13/16
13/16
MODEL
AC SPECS
120VAC
0.90W
N/A
N/A
BULB II
120VAC
2.6W
120VDC
2.6W
ORDERING INFORMATION
SERIES
BULBI/HB= standard version
BULBII/HB= with or without in-line diodes
(2.5W), high brightness
2
My existing incandescent exit lamps last
for:
4 Months
My replacement labour cost:
$25.00/Hour
Estimated lamp replacement
time per exit:
20 Minutes
Current material cost for each
Exit Sign lamp:
$1.00/Lamp
$0.060/$ Per kWh
THE PAYBACK FOR YOUR INSTALLATION IS:
1.06 Years
THE ANNUAL RETURN ON INVESTMENT IS:
94.50 %
$70.87
FOR MORE INFORMATION, PLEASE CONSULT YOUR SALES
REPRESENTATIVE.
DC SPECS
BULB I
15W
1.7W
ANNUAL SAVINGS:
POWER CONSUMPTION
$5.00
Wattage rating of Emergi-Lite LMRUNIV
retrofit kit:
My current energy cost:
51/3” [13 cm]
33/4” [9.6 cm]
43/4” [12 cm]
15/16
$70.00
BASE
C= candelabra
I= intermediate
M= medium
B= bayonet
F= G23 compact
fluorescent
EXAMPLE: BULBI-C
86
Project/Location:
Contractor:
Pendant Kit
Date:
Prepared by:
DIMENSIONS
TYPICAL SPECIFICATIONS
Dimensions are approximate and subject to change.
Offered in a variety of colours and lengths, Emergi-Lite® Pendant
Kits are designed to facilitate the installation of Exit Signs at regular
mounting heights.
P1E
Compatible with both horizontal and sloped ceilings, these Pendant
Kits is truly universal and will adapt to any application.
Length
Please consult your sales representative.
P2E
ORDERING INFORMATION
SERIES
LENGTH (IN)
COLOUR
P1E*
6
12
18
24
W= white
B= black
SG= silver grey
P2E*
6
12
18
24
W= white
B= black
SG= silver grey
P23E*
*Edge-Lit
6
12
18
24
W= white
B= black
SG= silver grey
P4E*
*New Premier™ Plastic Exit
6
12
18
24
W= white
B= black
*Other lengths available on demand. Consult your sales representative.
87
Project/Location:
Contractor:
Wire Guards
Date:
Prepared by:
EXIT SIGNS
PART #
MOUNTING
DIMENSIONS
SIGNS
W
H
D
10 1/2”
(26.7 cm
6”
(15.2 cm)
16”
(40.6 cm)
14 1/2”(36.8 cm)
6 1/4”
(15.9 cm)
10 1/2”
(26.5 cm)
28 1/8”
(71.5 cm)
21 1/8”
(53.7 cm)
10”
(25.4 cm)
End Mount
LPEX100
LPEX50
LPEX600-N Series - Nema-4X
Exit
EX160
LPEX300
460.0028-E
Ceiling Mount
LPEX100
LPEX50
LPEX600 - Nema-4X
EX160
460.0034-E
Wall Mount
12ESL-SR Sortie
WP36
LPEX300
EX10
EN
SR160
ES
12ESL-EX
C8SRPK-P
460.0048-E
End Mount
LPSR100
C8SR50
LPSR300
C8SR10
10 1/2”
(26.7 cm)
6”
(15.2 cm)
21”
(53.3 cm)
460.0057-E
Wall Mount
LPSR100
C8SR50
LPSR300
C8SR10
20 3/4”
(52.7 cm)
10” (25.4 cm)
4” (10.2cm)
460.0058-E
Ceiling Mount
LPSR100
C8SR50
LPSR300
C8SR10
21 3/4”
(55.2 cm)
5 1/2”
(14 cm)
10 1/2”
(26.7cm)
460.0059-E
Wall Mount
C8ES300 bilingual
C8SE10
C8ES70 bilingual
C8ES10
460.0060-E
End Mount
LPEX600-N - Nema-4X Combo
EX10-P
460.0060-E
Wall Mount
EN
LPEX600-N Combo
EX10-P
31”
(86.4 cm)
20”
(50.8 cm)
20”
(50.8 cm)
10”
(25.4 cm)
12”
(30.5 cm)
12”
(30.5 cm)
4 1/2”
(14 cm)
15”
(38.1 cm)
15”
(38.1 cm)
460.0078-E
Wall Mount
C8SR50-P Combo
LPEX600-N - Nema-4X Combo
EX10-P
ENC
Premier™ Combo
18”
(45.7 cm)
18”
(45.7 cm)
7”
(17.8 cm)
460.0079-E
Wall Mount
LPEX100
LPEX50
LPEX600 - Nema-4X
EX160
LPEX300
EX10
Premier™ Exit
EN
ES
SR160
14 1/4”
(36.2 cm)
9 7/8”
(25.0 cm)
4 5/8”
(11.7 cm)
460.0080-E
Wall Mount
EXHZ combo (class1 Div2)
LPEXHZ Exit
15 1/4”
(38.7 cm)
14 1/8”
(35.9 cm)
6 1/2”
(16.5 cm)
460.0081-E
Wall Mount
12ESL-EX, EAC, EX10-P,
SR, ESC
20”
(50.8 cm)
17 1/8”
(43.6 cm)
8 1/2”
(21.6 cm)
460.0091-E
Wall Mount
EX10-P
15”
(38.1 cm)
10 1/2”
(26.7 cm)
1”
(2.5 cm)
460.0092-E
Ceiling Mount
C8SR10
C8ES300 Bilingual
C8ES70
EX10-P
C8ES70
31”
(53.3 cm)
4.5”
(11.4 cm)
10”
(25.4 cm)
460.0103-E
Wall Mount
C8SRPK-P
460.0104-E
End Mount
C8SR10
C8E/S35R
25”
(63.5 cm)
10”
(25.4 cm)
20”
(50.8 cm)
460.0027-E
EX10
EN
SR160
ES
88
Project/Location:
Contractor:
Wire Guards
Date:
Prepared by:
BATTERY UNITS
PART
MOUNTING
COMMERCIAL, DECO UNIT
460.0078-E
Wall Mount
460.0081-E
460.0034-E
460.0097-E
DIMENSIONS
W
H
D
“A” Cabinet-6V, 12V, 24V-Max. 144W
8”
(45.7 cm)
8”
(45.7 cm)
7” (17.8 cm)
Wall Mount
“B” Cabinet-6V-180W
12V-200 to 360W
24V-200 to 288W
20” (50.8 cm)
17 1/8”
(43.6 cm)
8 1/2”
(21.6 cm)
28 1/8”
(71.5 cm
21 1/8”
(53.7 cm)
10” (25.4 cm)
Wall Mount
“C” Cabinet-12V-650watts
24V-350 to 720W
Q-BIC
31”(53.3 cm)
70”(17.8 cm)
6”(15.2 cm)
SMALL, 6V
460.0080-E
Wall Mount
14 1/8”
(35.9 cm)
6 1/2”
(16.5 cm)
9” (3.5 cm)
9” (3.5 cm)
17 1/8”
(43.6 cm)
8 1/2”
(21.6 cm)
15 1/4”
(38.7 cm)
6V, 12V - 18 to 72W
INDUSTRIAL
460.0082-E
Wall Mount
460.0081-E
Small Cabinet
12” (30.5 cm)
Medium and Largel Cabinet
20” (50.8 cm)
REMOTE HEADS
PART #
DIMENSIONS
REMOTE HEADS
W
H
8 1/4” (21.5 cm)
D
460.0029-E
EF9, EF9Q, EF9M, EF11, EF25
6 1/4” (15.9 cm)
6 3/4” (17.2 cm)
460.0031-E
EF26D, EF18T, EF11D
460.0032-E
EF26DS, EF150
25 1/4” (64.1 cm)
8 1/2” (21.5 cm)
8 1/2” (21.5 cm)
9 1/2” (24.1 cm)
9 1/2” (24.1 cm)
6 1/8” (15.6 cm)
460.0033-E
460.0035-E
EF15
9 1/2” (24.1 cm)
9 1/2” (24.1 cm)
4”(10.2 cm)
EF18, EF11, EF30, EF26, EF39, EF40
8 1/4” (21.5 cm)
6 1/4”(15.9 cm)
8 1/2” (21.5 cm)
460.0082-E
EF18D, EF11D, EF30D, Literay™, Lux-Ray™, Retract-a-Lite™
12”(30.5 cm)
9”(22.9 cm)
9”(22.9 cm)
460.0100-E
Provider™
14”(35.6 cm)
5.8”(14.7 cm)
5.6”(14.2 cm)
MOUNTING SHELVES
PART # 440.0616-E FOR “A” CABINET
PART # 440.0620-E FOR “B” CABINET
1029/32” [27.69 cm]
71/2”
[19.05
cm]
71/2”
[19.05
cm]
81/32”
[20.4 cm]
51/16”
[12.89
cm]
81/32”
[20.4 cm]
181/16” [45.85 cm]
63/16”
[15.75
cm]
89
111/16” [28.07
cm]
111/32” [28.02
cm]
115/16” [28.7 cm]
151/16” [38.28 cm]
PART # 440.0625-E FOR “C” CABINET
253/32” [63.75 cm]
69/32”
[15.93
cm]
Project/Location:
EZ2 Canopy
™
Quick and Easy Installation
Contractor:
Date:
Prepared by:
DIMENSIONS
63/8”
The EZ2™ Canopy allows the installer to make all of the electrical
connections using both hands without having to juggle with the Exit
Sign, making it our most contractor friendly product feature to date.
Simply attach the backplate to the junction box, clip the canopy on
the Exit Sign, hang the canopy on the back plate, make your
connections using both hands, slide the unit in place, one screw and
the job is done!
11/32”
411/16”
See detail A
See detail C
See detail B
3. Connect the wires, then align and
slide the sign to its final position.
1. Attach the backplate/spider to
the wall before assembly.
2. Hang the unit using
the tabs and the wire eyes.
Detail A
Scale 3.000
Detail B
Scale 3.000
90
Detail C
Scale 3.000
Project/Location:
Contractor:
Date:
Prepared by:
GLOSSARY
U
Auto-diagnostic
Automatically tests and continuously monitors your emergency lighting unit. If a problem occurs, the unit will send a visual
(flashing or blinking LED indicator) and audible warning. Complies with Fire Code requirements.
UN
Auto-diagnostic
(non-audible)
Automatically tests and continuously monitors your emergency lighting unit. If a problem accurs, the unit will send a visual
(flashing or blinking LED indicator) warning. Complies with Fire Code requirements.
CT
Cab-tire
Unit supplied with a cab-tire cable used for special hardwire applications.
CW1
Cold weather, 120VAC
120VAC input cold weather protection feature for applications where temperatures can reach -40° C.
CW3
Cold weather, 347VAC
347VAC input cold weather protection feature for applications where temperatures can reach -40° C.
Line cord (120V)
When ordering a battery unit with the LC option, we supply and pre-install a line cord with a standard 3 prong 120V plug.
Just hang the fixture and plug it in to a standard receptacle! Only available on 120V units.
FP
Teflon coated lens
A protective teflon coating that is applied to the glass lens of a lighting fixture to prevent broken shards from falling in the
event the glass is accidently broken or vandalised.
X2
Remote test receiver
Used to perform maintenance tests by means of radio receiver in conjunction with a transmitter (HHC option) on battery
units that are out of reach. Simply point the receiver at the unit.
NEXUS® system interface
The NEXUS® system interface is a computerized maintenance system for emergency lighting that, once programmed, will
perform the tests, keep written records and send a notification if anything needs to be fixed. One full system can address
hundreds of units in as many buildings as you need from a single location.
Time delay (15 minutes)
Normally, when the AC power is restored, all emergency lighting lamps are turned off. However, in some cases, such as
when metal halide lamps are used, it is possible that the general lighting will not be available for several minutes after the
blackout (or brownout) period. Battery units with the D3 option will keep some energy in store to ensure that the emergency
lighting stays on or comes back on for at least 15 minutes once the regular AC power has been restored.
Time delay
(programmable)
Same as the D3 option but can be programmed for 5, 10 or 15 minutes delay.
TP
Tamper-proof screws
Screws that require a special bit. Can be used on certain units to deny access to unauthorized personnel.
TL
Twistlock plug
Used to facilitate the connection and removal of battery units for maintenance purposes.
L
NEX
D3
D
91
LUX-RAY
DISTINCTION
SURVIVE-ALL
SIPE
IPE
RETRACT
-A-LITE
JMLC
ESLPK
JMLA
ECLIPSE
BATTERY
UNITS
93
Project/Location:
Contractor:
TABLE OF CONTENTS
Date:
Prepared by:
Project/Location:
MR16 LED EMERGENCY LIGHTING
Contractor:
Date:
Prepared by:
MR16 LED ILLUMINATION
MR16 LED LAMP BENEFITS
With the remarkable technology development in the last
decade, the light-emitting diode (LED) is becoming the
preferred solution in low- and medium-power lighting
applications. The emergency lighting industry is no
exception: today virtually every new product introduced to
market includes “white” LEDs for emergency illumination.
• CSA C22.2 No. 141 certified.
• Energy-efficient LED MR16 lamp provides equivalent
lighting performance to a much higher watt halogen
MR16 lamp.
• Reduces required battery capacity by 75%, providing
necessary illumination with fewer remote heads and
battery units for project cost savings.
Extremely efficient and long-lasting, LED lamps become the
natural alternative to incandescent lamps due to three main
advantages:
• Small profile, compact white lighting is ideal for
architectural applications.
• = lamp efficacy: 50 - 70 lumen per watt compared to 15 30 lumen per watt of the best halogen lamp.
• Vibration-resistant LED stands up to industrial
environments.
• = operational life: 30,000+ hours, equivalent to a lifetime
warranty in emergency lighting.
• Ideal for indoor and outdoor use.
• = lower lamp temperature (80 - 120°C) is a huge benefit
for lighting in hazardous locations.
340-LUMEN 5W MR16 LED
200-LUMEN 4W MR16 LED
Keeping pace with technology, in 2012 we introduced a
12V-5W MR16 LED lamp. With a typical luminous flux of 340
lumens, this lamp has the same lighting performance as
a 20W high-output halogen MR16. A twin emergency head
installed at a height of 7.5ft illuminates more than a 70ft
path of egress.
Leading the technology trend, Emergi-Lite® offers a
complete series of 4W MR16 LED lamps available for all
the standard battery voltages: 6V, 12V, 24V and 120V. With
up to 30,000 hours of operational life and a luminous
flux of typically 200 lumens, they are available with most
emergency heads designed to hold an MR16 lamp and meet
the majority of illumination specifications. For example: one
pair of LED emergency heads installed at a height of 7.5ft,
illuminates a 6ft by 40ft path of egress.
510-LUMEN 6W MR16 LED
New in Fall 2013, we intoduce a 12V - 6W MR16 LED lamp,
which offer typical luminous flux of 510 lumens. Like the
lower wattage MR16 LED lamps, this new lamp is specially
designed for emergency lighting. It offers the same lighting
preformance as the 35W or 20W Mr16 IR. A twin emergency
head installed at a height of 7.5’ illuminates approximately
100’ path of egress.
Compared to halogen lamps (16-20W), these 4W MR16
LED lamps illuminate the same area of egress during an
emergency situation by using 75% less power. This has
a direct impact on the battery size, reducing the back-up
capacity needs by 75%. Consequently, it also reduces the
total cost of the application, with the use of smaller battery
capacity units, the possibility of using fewer fixtures due to
superior illumination, thus also reducing electrical wiring,
and it it reduces the environmental footprint.
40-FT. PATH OF EGRESS 2 X 4W MR16 LED
70-FT. PATH OF EGRESS 2 X 5W MR16 LED
6
INTRODUCTION
LUX-RAY LED SERIES
RETRACT-A-LITE
SERIES
MINI RETRACT-ALITE SERIES
PROVIDER SERIES
DISTINCTION
RECESSED SERIES
DISTINCTION
SERIES
DEL SERIES
P. 96-97
P. 98-99
P. 100
P. 101
P. 102
P. 103
P. 104-105
P. 106-107
ESLT SERIES
WONDERPACK WP36
SERIES
ECLIPSE SERIES
JMLC SERIES
JMLA SERIES
JEMP18 SERIES
PREMIER SERIES
ESL SERIES
P. 108-109
P. 110
P. 111
P. 112-113
P. 114
P. 115
P. 116-117
P. 118-119
GLOSSARY
U
Auto-diagnostic
Automatically tests and continuously monitors your emergency lighting unit . If a problem occurs, the unit will send a visual
(flashing or blinking LED indicator) and audible warning . Complies with Fire Code requirements .
UN
Auto-diagnostic
(non-audible)
Automatically tests and continuously monitors your emergency lighting unit . If a problem accurs, the unit will send a visual
(flashing or blinking LED indicator) warning . Complies with Fire Code requirements .
CT
Cab-tire
Unit supplied with a cab-tire cable used for special hardwire applications .
CW1
Cold weather, 120VAC
120VAC input cold weather protection feature for applications where temperatures can reach -40° C .
CW3
Cold weather, 347VAC
347VAC input cold weather protection feature for applications where temperatures can reach -40° C .
L
Line cord (120V)
When ordering a battery unit with the LC option, we supply and pre-install a line cord with a standard 3 prong 120V plug .
Just hang the fixture and plug it in to a standard receptacle! Only available on 120V units .
A protective teflon coating that is applied to the glass lens of a lighting fixture to prevent broken shards from falling in the
event the glass is accidently broken or vandalised .
FP
Teflon coated lens
X2
Remote test receiver
Used to perform maintenance tests by means of radio receiver in conjunction with a transmitter (HHC option) on battery
units that are out of reach . Simply point the receiver at the unit .
NEX
D3
D
NEXUS® system interface
The NEXUS® system interface is a computerized maintenance system for emergency lighting that, once programmed, will
perform the tests, keep written records and send a notification if anything needs to be fixed . One full system can address
hundreds of units in as many buildings as you need from a single location .
Time delay (15 minutes)
Normally, when the AC power is restored, all emergency lighting lamps are turned off . However, in some cases, such as
when metal halide lamps are used, it is possible that the general lighting will not be available for several minutes after the
blackout (or brownout) period . Battery units with the D3 option will keep some energy in store to ensure that the emergency
lighting stays on or comes back on for at least 15 minutes once the regular AC power has been restored .
Time delay
(programmable)
Same as the D3 option but can be programmed for 5, 10 or 15 minutes delay .
TP
Tamper-proof screws
Screws that require a special bit . Can be used on certain units to deny access to unauthorized personnel .
TL
Twistlock plug
Used to facilitate the connection and removal of battery units for maintenance purposes .
89
SURVIVE-ALL™ NXM
SERIES
IPE SERIES
SIPE SERIES
ESLPK SERIES
HZM SERIES
ESLNX SERIES
48 & FPS SERIES
GLOSSARY
P. 120-121
P. 122
P. 123
P. 124-125
P. 126-27
P. 128-129
P. 130
P. 131
95
Project/Location:
BATTERY UNITS OVERVIEW
Contractor:
Date:
Prepared by:
LIFE SAFETY EQUIPMENT
BATTERY UNITS AND REMOTE HEADS
Emergency Lighting, as part of Life Safety Equipment, is one of
the key elements to ensure public safety within buildings. In the
event of failure of the normal power supply, self-powered units
automatically provide the illumination required to evacuate the
building in safe conditions.
There are also battery powered units that will supply power to
several remote emergency lights of different wattages (12W, 20W,
50W, etc.). In this case, remote emergency lights (also referred to
as remote heads) are installed in rooms and corridors, connected
by wiring installed inside the walls. Some 6V self-contained fixtures
can assume a total emergency lighting load up to 150W – 180W.
At this level, the battery current (25A – 30A) begins to generate
significant losses in the external wiring. For this reason, there are
battery units of higher voltages, 12V and 24V, which can respectively
supply power to remote heads totalling up to 360W and 720W.
STANDARDS AND CODES
Requirements for the installation, level, and duration of emergency
lighting in buildings are established by national standards: the
National Building Code of Canada (CNBC-2005), the Canadian
Electrical Code (CEC), and the National Fire Code of Canada
(NFC-2005). Concerning the equipment, performance is established
by the Canadian Standards Association (CSA), for example:
C22.2 No.141, C860, etc.
CENTRAL SYSTEMS
A higher wattage capacity emergency system is a Central System.
In the event of a utility power failure, Central Systems continue to
supply power to the emergency lighting equipment as well as other
critical loads. A Central System that supplies power during a utility
power failure is an emergency power system of which there are two
types of Central Systems: the Direct Current Central System (DC
System) and the Alternating Current Central System (AC inverter,
UPS or Uninterruptible Power Supply/System). The electric power
supplied by these systems can vary from a few KVAs to several
hundred KVAs.
TYPES OF EMERGENCY LIGHTING
Emergency lighting equipment is divided in two main categories:
self-powered emergency lighting equipment, also referred to as
“unit equipment for emergency lighting’’, and central emergency
power systems (separate emergency electrical power supply).
SELF-POWERED
(OR SELF-CONTAINED) EQUIPMENT
INDUSTRIAL ENVIRONMENT
The industrial environment is the most severe in terms of
housing construction requirements. It is defined by a number of
parameters specific to various technical processes within the industry:
temperature range, degree of humidity, degree of protection against
water and dust, resistance to corrosive chemicals, presence of
flammable gases and vapors or combustible particles, etc. An
important performance factor is the degree of protection against
solid particles (dust, etc.) and liquids. This rating is generally defined
and measured as established by the American standard NEMA
250-2003 from the National Electrical Manufacturers Association,
or, alternately, the European IP (ingress protection) code of the
International Electrotechnical Commission (IEC 60529 standard).
To accomplish the required degree of protection and resistance to
corrosive agents, emergency lighting fixtures are designed/fabricated
with gasketed, rugged, polycarbonate or fiberglass housings.
The most common self-powered unit consists of a 6V lead battery
and two lamp heads, also referred to as emergency lights, each
with a 6V, 9W incandescent lamp. Lamps are normally off; the
storage battery has sufficient capacity to actuate and maintain the
emergency lighting for at least 30 minutes in the event of a power
failure. In some applications described in the National Building
Code of Canada, the minimum emergency lighting period can reach
60 minutes or even 120 minutes. This will require battery units of a
greater capacity. Once normal AC power supply is restored, heads
turn off (if they were still on), the fixture recharges the batteries to
full capacity within 24 hours, then returns to the stand-by mode.
A special category exists covering hazardous areas, defined by
technological processes generating (or susceptible to generate)
flammable gases, vapors, flammable liquids or combustible dust
particles in explosive concentrations in the atmosphere. Hydrogen
or acetylene plants, gasoline and natural gas refineries, coal
or magnesium mines, flour mills and textile factories are some
examples. For more details on definitions and classifications of
hazardous areas, consult the Canadian Electrical Code
(CSA C22. 1-06).
96
Project/Location:
Contractor:
Date:
Prepared by:
Considering the risks of explosion or fire, all equipment dedicated
to hazardous areas must meet, special standards such as:
CSA C22.2 No. 30-M1986, No. 137-M1981, No. 213-M1987, etc.
Based on each respective classification (Class, Division, Group),
enclosures and remote heads for hazardous areas are fabricated
of materials which must meet stringent requirements (pure forged
aluminum, fiberglass, etc.) and may require specific components,
such as seals, valves, gasketing, etc in addition to standards
specific to emergency lighting. In view of all these additional
specific characteristics, it can be expected that emergency lighting
equipment approved for hazardous areas will cost more than
fixtures classified for general industrial applications.
The specifier can opt for a higher capacity unit (e.g.: 24V, 720W or a
central DC System) installed in a hidden location, to supply power
to remote heads distributed throughout the building. Another option
would be to install recessed self-contained units concealed in the
ceiling (T-bar), each with two lamp heads and additional capacity
for remote heads. There are also single-lamp battery units (MR16
or PAR36) that can be recessed in the ceiling. As for remote heads,
they are generally fabricated of forged aluminum and contain
halogen MR16 lamps. It is also possible to conceal the battery units
as well as the lamp heads entirely. For example, both the lamp
heads and the housing of the PHANTOM self-contained unit are
concealed in the wall or ceiling cavity, behind its door which rotates
180°. Upon power failure, an electromechanical device opens the
door and exposes the emergency lamp heads to illuminate the path
to safety. At the end of the power failure, this same device retracts
the heads and closes the door.
EMERGENCY LIGHTING ENCLOSURES
Construction requirements for emergency lighting fixtures depends
on the location where the equipment is to be installed. Of all the
components, the enclosure (box or housing) is probably the most
affected by the type of environment where it is located.
To address specifiers’ needs for aesthetics, manufacturers have
developed new products for high end emergency lighting:
dual-function decorative luminaires providing both normal lighting
and emergency lighting. The lamps are powered by one of the
two independent electrical circuits: AC circuit for normal lighting
(including the wall switch), and an uninterrupted AC circuit for
the battery charger and control of the emergency lighting. Since
normal lighting levels are higher than those required for emergency
lighting, manufacturers also offer the same type of luminaire for
normal lighting only. This option provides the final user with the
possibility of alternating self-contained units with standard lighting
fixtures, while maintaining consistency of design.
The enclosure plays many roles: it provides the fixture with a degree
of protection against the environmental conditions, while meeting
technical, aesthetic and functional requirements. Of course, cost
can also be a deciding factor when selecting a fixture.
In general, non-residential lighting is divided in three market
segments: commercial, institutional and industrial. This market
segmentation still applies in the case of emergency lighting.
Typically, the commercial and institutional sectors are more
sensitive to costs and aesthetics, whereas the industrial sector is
more influenced by the technical aspects (fixture durability, etc.).
COMMERCIAL AND INSTITUTIONAL
ENVIRONMENTS
Commercial spaces (stores, restaurants, theatres, hotels, etc.) as
well as institutions are generally air conditioned, so the equipment
operates in normal temperature and humidity conditions. Generally,
the main selection criteria is total lighting costs, which include
equipment and installation. The most economical design for
self-contained units uses sheet metal housings of a neutral
color: white or beige. For the most part, exit signs are housed in
a rectangular box fabricated of steel (sheet metal) or extruded
aluminum, and illuminated from a light source contained within the
assembly (back-lit). Some molded plastic housings also exist (less
expensive material, but also less rigid than metal) – mostly used for
small battery units (lower wattages) and EXIT signs in provinces.
Even if aesthetics is a secondary criteria, manufacturers continue
to develop products which offer a more contemporary look.
AESTHETICS AND ARCHITECTURE
Fortunately, price isn’t everything in the buying decision process.
Some hotel chains, high-end stores and corporate headquarters
are excellent examples.
In these situations, the architect and the lighting designer have
a great influence in specifying emergency lighting fixtures.
The question becomes – what will the architect prefer, a more
decorative or a more unobtrusive, discreet look?
Battery units are becoming increasingly discreet.
97
Project/Location:
Lux-Ray™ LED Series
Rugged, Versatile, Sophisticated
FEATURES
Prepared by:
TYPICAL SPECIFICATIONS
OPTIONS
• Cold weather: (-40°C... 30°C)
• Forward-throw light distribution, for applications of outdoor
exit discharge (OSHA 1910.36)
• High-lumen output: 25 to 50% additional level of illumination
compared to standard models
• Dual-mode operation: normal lighting and/or emergency
lighting with separate AC inputs
• Photo-switch: dusk-to-dawn control of normal lighting
• Remote test: infrared remote control
(keyboard ordered separately)
• Time delay: 15 minutes
IN THE SAME FAMILY
Luxray™ LED Remote Fixture
P.138
NEMA-3R
POWER CONSUMPTION
AC SPECS: 120/347VAC
NORMAL LIGHTING
EMERGENCY LIGHTING
CURRENT (MAX)
POWER (MAX)
CURRENT (MAX)
POWER (MAX)
ACSD, SD, SD-H
0.12/0.05 A
12W
0.05/0.02 A
5W
SD-CW
-
-
0.16/0.06 A
16W
0.24/0.10 A
24W
ACSD-CWP, -CW-RC
Date:
Supply and install the Lux-Ray™ Series of LED emergency lighting
from Emergi-Lite®. The unit body shall include a back-plate and
housing made of Die-Cast aluminum with paint finish color: _______
and a UV- and impact-resistant polycarbonate lens of reduced size:
3-in by 1.5-in. The back-plate shall have knockouts for wires and
wall-mount installation box as well as a threaded hole for rigid
conduit entry at the top of the unit. The back-plate shall have a
built-in electrical box with wire terminals and snap-on connector.
After complete electrical installation of the back-plate the equipment
housing shall be installed by a simple push & snap over the
back-plate.
The emergency lights shall be 4 (four) power light-emitting diodes
(LED) with operational life of minimum 36,000 hours, maintaining at
least 70% of the initial light level (reported L70). The LED lamps shall
have redundant interconnections: eventual failure of one lamp shall
allow other LED lamps to function. The unit shall have a
dual-voltage input rated 120/347VAC, 60Hz. The battery charger shall
include low voltage disconnect to prevent deep discharge, battery
lockout to prevent battery drain prior to energizing the utility power,
and brownout protection which will automatically switch the unit into
emergency mode if the utility power falls below 80% of nominal level.
The unit with Nickel-Metal Hydride battery shall be equipped with
a micro-controller-based non-audible auto-test circuit and provide
minimum 90 minutes of emergency lighting. The unit shall self-test
for one minute every month, 30 minutes every six months and 90
minutes annually.
The pilot light shall be integrated with the test button; it shall
be a bi-color LED and shall change color from normal green to
flashing red when a failure is detected from the battery, charger
circuit or lamps. A label located near the pilot light shall describe
the diagnostic for each flashing code. When specified, models with
dual-mode illumination shall include two separate AC input circuits:
un-switched for emergency lighting and switched for normal
lighting. When specified, models equipped with photo-switch shall
automatically activate the normal lighting only from dusk till dawn,
for additional energy savings. The typical ambient illumination for
the photo-switch shall be 10 lux (to turn-on) and 30 lux (to turn-off).
When specified, the unit shall be controlled by an infrared remote
control keypad (ordered separately). The remote control shall be able
to simulate a power failure of 1 minute, 30 minutes or 90 minutes
and also to cancel the test in progress at any time. For units with
dual-mode lighting the remote keypad shall also control the normal
lighting with on/off switch and dimming functions. The unit shall
be certified to CSA 22.2 No.141-10 for minimum 90 minutes and
No.250.0-08 standards.
The unit shall be Emergi-Lite® model:
.
• Die-Cast aluminum housing, available in four finishes:
dark bronze, off-white, black, and platinum gray
• NEMA-3R Rated for indoor/outdoor wet and damp locations:
0… 40°C
• Wall-mount installation on various junction boxes or via rigid
conduit
• Patent-pending design for easy installation: wall-mount
backplate includes electrical wire box with snap-on connector
• Patent-pending light engine: four power LEDs with redundant
inter-connections and very wide beam
• Clear polycarbonate lens of reduced size (3” x 1.5”),
shock-absorbent and UV-resistant
• Battery: high-temperature rated, Nickel-Metal Hydride
technology
• Power consumption in stand-by: less than 5W
• Self-Test and diagnostic functions operated by
micro-controller
• Certified to CSA 22.2 No.141-10 and No.250.0-08 standards
• 90 minutes run time
MODEL TYPE
Contractor:
n/r*
*Note: Only unswitched AC input; normal lighting with photo-switch or remote control
98
6-12VDC REMOTE
POWER (MAX)
NiMH battery
Project/Location:
Contractor:
Lux-Ray™ LED Series
Date:
Rugged, Versatile, Sophisticated
Prepared by:
TABLE A: SPACING FOR AVERAGE 1FC/NATIONAL
BUILDING CODE, CANADA
WIDE BEAM (STANDARD)
WATTAGE CAPACITY
MODEL TYPE
MOUTING
HEIGHT
SINGLE
CENTRE-TO-CENTRE
Standard
9’
6’ X 50’
6’ X 50’
With option -H
11’
6’ X 60’
With option -FT
12’
6’ X 40’
6’ X 60’
3’ X 70’
-
With option -FTH
15’
6’ X 50’
-
1FC
1FC average
50’
min
imu
28’
m
9’
Indoor reflectance: 80/50/20 and 10-ft wide corridor.
Outdoor reflectance: 0/30/10
6’
Note: The illumination level meets ALL the requirements of the National
Building Code-Canada and the Life Safety Code (NFPA 101):
1) Average of 1 foot-candle or more
2) Minimum at any point of 0.1 foot-candle or more
3) Maximum-to-minimum illumination uniformity ratio of 40:1 or less
FORWARD THROW (OPTIONAL)
TABLE B: SPACING FOR MINIMUM 1FC MAX./
MIN. UNIFORMITY RATIO LESS THAN 3:1
m
imu
min
1fc
WATTAGE CAPACITY
MOUTING
HEIGHT
SINGLE
CENTRE-TO-CENTRE
Standard
9’
4’ X 28’
4’ X 32’
With option -H
With option -FT
11’
12’
4’ X 32’
4’ X 22’
4’ X 40’
-
With option -FTH
15’
4’ X 27’
-
MODEL TYPE
12’
age
aver
1fc
40’
6’
DIMENSIONS
REMOTE CONTROL
Dimensions are approximate and subject to change.
Patent Pending
3” [7.5 cm]
22’
3” [7.5 cm]
6-5/8” [16.8cm]
EMERGENCY LIGHTING
9-1/2” [24 cm]
NORMAL LIGHTING WITH
SWITCH & DIMMING
Window for
photo-switch
(optional)
PART#: TB-RC1-E
ORDERING INFORMATION
SERIES
LUX= L
ux-Ray™ LED
FUNCTION: BATTERY UNITS
SD= Self-Powered & diagnostic
(0… 50°C)
ACSD= Dual-mode AC/Self-Powered
& diagnostic
(0… 40°C)
COLOUR
BK= black
BZ= dark bronze
OW= off white
PG= platinum grey
OPTIONS
-CW= Cold weather (-40°C... 30°C; not available with option -H)
-FT= Forward throw lighting
-H= High lumen output (max. 30°C; model SD only)
-P= Photo-switch (model ACSD only)
-RC= Remote control - infrared*
-D3 = time delay (15 minutes)
-2 = 277VAC 60Hz input
* Remote control keypad (TB-RC1-E) ordered separately.
EXAMPLE: LUXACSDBZ-P
99
Project/Location:
Retract-a-Lite™
Series
Contractor:
Date:
Prepared by:
100% Recessed Emergency Lighting
FEATURES
TYPICAL SPECIFICATIONS
• Door flips 180° when AC fails
Supply and install Emergi-Lite® Retract-a-Lite™ Series. The unit
shall be designed to be concealed in walls or ceilings with a cavity,
including T-bar suspended ceilings. Bar hanger brackets shall be
provided with the Self-Powered unit. The unit equipment shall come
standard with a metal back box containing the batteries, the lamp
assembly and a charging circuitry. The back box shall be constructed
of heavy-duty galvanized steel. The unit components: battery
assembly, charger circuitry and lamp assembly shall have a modular
design and come standard with quick-connect plugs for easy
installation in the back box. The unit equipment shall be completely
concealed in the wall or ceiling during normal power conditions.
Upon a power failure the unit will expose the emergency heads by
rotating its door 180° and then power the lamps. At the restoration
of the AC power or at the end of the battery discharge, the lamps
will turn off and the unit will retract the heads in the wall (ceiling) by
rotating the door by 180°. Under normal conditions, the only visible
parts of the unit shall be the flat door and trim plate, coated with
a high-quality off-white finish that can be customized on site with
paint or other suitable wall covering. The light source shall be 12V
MR16 halogen lamps of specified wattage and light output. The unit
shall supply the rated load for a minimum of 30 minutes or until the
battery is discharged to 87 ½% of its nominal voltage (whichever
duration is longer). The charger circuitry shall utilize a
micro-controller IC that samples the battery in relation to the
ambient temperature, state of charge, and input voltage fluctuations.
The charger shall be current limited, temperature compensated,
short-circuit proof, and reverse-polarity protected. The circuit will
charge in accordance with CSA C22.2 – 141 requirements. The unit
shall be furnished with a recessed, illuminated push button serving
as test switch and status indicator light. When specified, the unit shall
come complete with Emergi-Lite® auto-test micro-controller circuitry
to ensure the equipment readiness and reliability by continuously
monitoring every critical function of the unit. If a problem occurs,
the pilot light located on the front of the unit will change color from
green to red and will flash indicating a fault. A detailed diagnostic
legend shall be available on the door back side and shall provide
fault identification (battery, charger circuitry, lamps) for maintenance
personnel.The auto-test shall simulate a power loss for one minute
monthly, 10 minutes every 6 months, and a full 30-minute test every
12 months.
The equipment shall be Emergi-Lite® model:
.
•F
ully automatic operation – brown-out sensitive transfer
circuit automatically goes to emergency lighting mode
and, when the power is restored or at the end of battery
discharge, the motor turns the door back to its original
closed mode (time delay option required).
•C
ustomized finish – unit sold in white but can be painted or
wallpapered on site to match existing décor
• Heavy-duty back-box – made of heavy-duty, galvanized steel
•H
igh-performance lighting– includes two MR16 halogen
lamps; power range from 2x12W up to 2x50W
• Patent-pending design
• Meets or exceeds CSA 22.2 No.141
DIMENSIONS
Dimensions are approximate and subject to change.
91/8” [23.2 cm]
3 ” [8.6 cm]
77/8” [20.0 cm]
7” [17.8 cm]
237/8” [60.6 cm]
3/8
REPLACEMENT LAMPS: MR16 TYPE
MODEL
LAMP TYPE
VOLTAGE/WATTAGE
580.0080-E
MR16 Halogen
12V-12W
580.0064-E
580.0083-E
580.0076-E
580.0068-E
MR16 Halogen
MR16 Halogen
MR16 Halogen
MR16 High-lumen output
12V-20W
12V-35W
12V-50W
12V-20W H
580.0090-E
MR16 High-lumen output
12V-35W H
580.0089-E
580.0093-E
580.0104-E
580.0106-E
MR16 High-lumen output
MR16 LED
MR16 LED
MR16 LED
12V-50W H
12V-4W
12V-5W
12V-6W
POWER CONSUMPTION
MODEL
RTL75
RTL150
AC ASPECS
120/347
VAC
0.25/0.09 A
WATTAGE CAPACITY
30MIN 1H00 1H30 2H00 4H00
75
40
30
24
15
150
80
60
48
30
ORDERING INFORMATION
SERIES
RTL
POWERPACK
75= 12V-75W
Lead-acid
150= 1
2V-150W
Lead-acid
VOLTAGE
Blank= 120/347VAC
-2= 120/277VAC
NUMBER OF HEADS
/12= MR16, 2x 12W
/20= MR16, 2x 20W
/35= MR16, 2x 35W
/50= MR16, 2x 50W
/20H= MR16, High lumen output, 2x 20W
/35H= MR16, High lumen output, 2x 35W
/50H= High lumen output, 2x 50W MR16
LG= MR16 LED, 12V-4W
LI= MR16 LED, 12V-5W
LJ= MR16 LED, 12V-6W
EXAMPLE: RTL150/35HU
100
OPTIONS
U= auto-diagnostics*
UN= auto-diagnostics,
non-audible*
D3= time delay (15 minutes)
*Minimum lamp load required: 20% of
unit capacity
Project/Location:
Mini Retract-a-Lite™
Series
Contractor:
Date:
Prepared by:
Unseen Solution the Next Generation
FEATURES
TYPICAL SPECIFICATIONS
• Easy to retrofit in finished walls: the unit slides in through an
8.25” by 5.75” hole
Supply and install Emergi-Lite® Mini Retract-a-Lite™ Series. The
unit shall be designed to be completely concealed in walls with a
cavity. The equipment shall consist of a metal housing containing two
modules joined by a flexible bracket and electric conduit. One module
contains the battery, charger circuitry and electrical connection box;
the other module contains the emergency lights installed on the back
of a door able to rotate several turns of 360°. The unit equipment
shall be completely concealed in the wall after installation through a
rectangular opening not larger than 8.25” by 5.75”. In stand-by mode,
the only visible parts of the unit shall be the flat door and trim plate,
coated with a high-quality off-white finish that can be customized on
site with paint or other suitable wall covering. Upon a power failure
the unit will expose the emergency heads by rotating its door 180°
and then will power the lamps. At the restoration of the AC power
or at the end of the battery discharge, the lamps will turn off and
the unit will retract the heads by rotating the door 180° in the same
direction. The unit shall not require the presence of AC power in
order to close the door and conceal the lights. The door of the unit
shall be easy to force-turn (open or close) by hand, in any rotation
direction. The light source shall be 12V MR16 lamps of specified
technology, wattage and light output. The unit shall supply the rated
load for a minimum of 30 minutes or until the battery is discharged
to 87.5% of its nominal voltage (whichever duration is longer). The
charger circuitry shall utilize a micro-controller IC that samples
the battery in relation to the ambient temperature, state of charge,
and input voltage fluctuations. The charger shall be current limited,
temperature compensated, short-circuit proof, and reverse-polarity
protected. The circuit will charge in accordance with CSA C22.2
– 141 requirements. The unit shall be furnished with a recessed,
illuminated push button serving as test switch and status indicator
light. When specified, the unit shall come complete with the
Emergi-Lite® series of auto-test micro-controller circuitry to ensure
the equipment readiness and reliability by continuously monitoring
every critical function of the unit. If a component failure occurs, the
pilot light located on the front of the unit will change colour from
green to red and will flash indicating a fault. A detailed diagnostic
legend shall be available on the back side of the door and shall provide
fault identification (battery, charger circuitry, lamps) for maintenance
personnel. The auto-test shall simulate a power loss for one minute
monthly, 10 minutes every 6 months, and a full 30-minute test every 12
months.
The equipment shall be Emergi-Lite® model:
.
• No back-box needed to pre-install
• Input: Standard AC input 120/347VAC; optional 120/277VAC
• Output: 12VDC with up to 100W of power
• Battery: choice of sealed, maintenance-free Lead-Calcium
or Nickel-Metal Hydride
• Remote capacity: can drive several wall or ceiling-mount 12VDC
remote Retract-a-Lite™ fixtures
• Charger: micro-controller driven, temperature compensated,
high precision, fast recharge
• Remote AC fixture: direct connection to 120 or 347VAC
power generators
• MR16 halogen lamps; power range from 12W to 50W, LED
4W and 5W
• Certification: CSA C22.2 No.141
DIMENSIONS
Dimensions are approximate and subject to change.
31/2” [8.9 cm]
COMPLETE UNIT
175/8” [44.8 cm]
51/4” [13.2 cm]
7” [17.8 cm]
91/8” [23.2 cm]
INSTALLED UNIT
REPLACEMENT LAMPS: MR16 TYPE
MODEL
LAMP TYPE
580.0080-E
MR16 Halogen
VOLTAGE/WATTAGE
12V-12W
580.0064-E
MR16 Halogen
12V-20W
580.0083-E
MR16 Halogen
12V-35W
580.0076-E
MR16 Halogen
12V-50W
580.0068-E
MR16 High-lumen output
12V-20W
580.0090-E
MR16 High-lumen output
12V-35W
580.0089-E
MR16 High-lumen output
12V-50W
MRL80
120/347VAC
-
80
40
24
-
120/347VAC
0.25/0.08 A
100
70
36
24
POWER CONSUMPTION AND UNIT RATING
MODEL
WATTAGE CAPACITY
30MIN 1H00 2H00 3H00
AC SPECS
580.0093-E
MR16 LED
12V-4W
MRH100
580.0104-E
MR16 LED
12V-5W
MRG1
120VAC
Max. 0.95 A
Maximum 100W load
580.0106-E
MR16 LED
12V-6W
MRG2
277VAC
Max. 0.45 A
Maximum 100W load
MRG3
347VAC
Max. 0.35 A
Maximum 100W load
ORDERING INFORMATION
SERIES
MR
POWERPACK
L80= Lead-Calcium,
12V-80W
H100= Nickel-Metal Hydride,
12V-100W
VOLTAGE
Blank=
120/347VAC
-2= 277VAC
NUMBER OF HEADS
/12= MR16, 2x 12W
/20= MR16, 2x 20W
/35= MR16, 2x 35W
/50= MR16, 2x 50W
/20H= MR16, High Lumen output, 2x 20W
/35H= MR16, High Lumen output, 2x 35W
/50H= MR16, High Lumen output, 2x 50W
LI= MR16 LED, 12V-5W
LG= MR16 LED, 12V-4W
LJ= MR16 LED, 12V-6W
EXAMPLE: MRL80/20HUN
101
OPTIONS
U= auto-diagnostics*
UN= auto-diagnostics, non-audible*
D3= time delay (15 minutes)
*Minimum lamp load required: 20% of unit capacity
Project/Location:
Contractor:
Provider™ Series
FEATURES
Date:
Prepared by:
TYPICAL SPECIFICATIONS
• Injection-molded, impact-, scratch- and corrosion-resistant
thermoplastic with a snap-together design
The contractor will install the Emergi-Lite® Provider™ Series battery
unit. The emergency lighting system shall consist of fully automatic
equipment with two (2) emergency lighting heads. The emergency
lighting heads shall require no tools for adjusting or aiming. Each
unit shall contain a fully automatic, solid-state charger with test
switch and AC-on pilot lights. The unit shall contain a sealed transfer
circuit and low-voltage disconnect circuit. The unit equipped with
self-testing /self-diagnostic or Nexus® features shall automatically
self-test for one minute every 30 days, 10 minutes in the 6th month
and 30 minutes annually. When a fault is detected, the bi-colour
pilot light shall turn from green to red and shall flash, identifying the
source of the failure: battery, charger circuitry, lamp load.
The battery shall meet 6V with a capacity of 20 or 36W for 30 minutes.
The unit shall be CSA C22.2 no 141.
.
The unit shall be Emergi-Lite® model: CPRO
•C
ompact and versatile – unit measures only 11.75” x 5” and
can be wall or ceiling mounted
•V
ariety of lamp types including optional MR16 LED lamps
with life expectancy of 50,000+ hours
• Maintenance-free, long-life sealed Lead Calcium battery
•F
ast and easy installation - AC quick connect plug, battery
knockout feature.
•F
ully automatic, solid-state charger with low voltage battery
disconnect, brownout protection, integral test switch and
long-life LED AC-On pilot lights
•C
harger is temperature compensated and reverse polarity
protected
WIRE GUARDS
•N
EXUS® compatible (For more information, please consult
your sales representative)
460.0080-E
• Meets or exceeds CSA 22.2 No.141
Wall Mount
REPLACEMENT LAMPS
DIMENSIONS
Dimensions are approximate and subject to change.
57/8” [15,0 cm]
LAMP TYPE
VOLTAGE/WATTAGE
570.0012-E
Mini tungsten, wedge base
6V–5.4W
580.0079-E
MR16 - Flood
6V–10W
580.0097-E
MR16 – LED
6V–4W
5” [12,7 cm]
113/4” [29.9 cm]
MODEL
POWER CONSUMPTION AND UNIT RATING
MODEL
WATTAGE CAPACITY
AC SPECS
CPRO-1N
120/347VAC
CPRO-2N
30MIN
1H00
1H30
2H00
4H00
0.07/0.03 A
20
15
12
8
-
0.08/0.03 A
36
21
15
12
6
ORDERING INFORMATION
SERIES
CPRO-1N= 6V, 20W
CPRO-2N= 6V, 36W
COLOUR
Blank= factory
white
B= black
INPUT VOLTAGE
Blank= 120/347VAC
2= 120/277VAC
UNIT TYPE
Blank= standard
-U= auto-diagnostics
-UN= auto-diagnostics,
non-audible
-NEX= NEXUS® system
interface*
-NEXRF= wireless NEXUS®
system interface*
* Available with CPRO-1N only
EXAMPLE: CPRO-1N-NEXRFVR/LA
102
OPTIONS
LAMP TYPE
Blank= no options
VR= vandal resistant screws
L= 120VAC c/w line cord –
supplied but not installed
VM= voltmeter*
CM= ceiling mount
TP= tamper-proof screws**
690.0454= tamper-proof bit**
/LA= MR16 LED, 6V-4W
/MJ= MR16, 6V-10W
/ZP= mini tungsten, 6V-5.4W
*Available with Standard unit
type only
** One but per order
Project/Location:
Distinction™ Series
Contractor:
Date:
Decorative Recessed Fixture
Prepared by:
TYPICAL SPECIFICATIONS
FEATURES
• Durable, powder-coated or electroplated Die-Cast aluminum
construction
Recessed heads and housings: The contractor will supply and install
Emergi-Lite® Distinction™ Series internally Self-Powered series. The
unit will have a dual input 120/347VAC 60Hz. Recessed heads will be
constructed of a durable powder coated, or electro plated Die-Cast
aluminum construction and use MR16 halogen light sources and a
5 year Nickel-Cadmium battery.
The recessed head will be adjustable to 0-90° vertical and 0-350°
horizontal angle. The light source will be 6V-6W, MR16 halogen
narrow beam or otherwise specified. The unit shall be equipped
with a sealed, high-temperature Nickel-Cadmium battery which will
supply the emergency lamp for minimum 30 minutes of illumination
in case of power failure.
The equipment shall be Emergi-Lite® Model:
.
• High-performance MR16 halogen light source
• Maintenance-free, sealed Nickel Cadmium battery
• Quick disconnect feature for easy trim installation; easy to access
for maintenance
• Fully automatic, solid-state Pulse-Guard charger with low voltage
battery disconnect, brownout protection, integral test switch and
long-life LED AC-On pilot lights
• Charger is designed for Nickel-Cadmium continuous trickle
charge and is reverse polarity protected
• Recessed, directional, retractable trim
REPLACEMENT LAMPS
• Meets or exceeds CSA 22.2 No.141
DIMENSIONS
ORDERING CODE
LAMP TYPE
580.0074-E
MR16
6V-6W
580.0079-E
MR16
6V-10W
Dimensions are approximate and subject to change.
5” [12.7 cm]
75/8” [19.4 cm]
VOLTAGE/WATTAGE
7” [17.8 cm]
IN THE SAME FAMILY
EFR Distinction™
CLOSED POSITION
o-90°
P. 147
5” [12.7 cm]
19” [48.3 cm]
OPEN POSITION
POWER CONSUMPTION AND UNIT RATING
MODEL
EFR2
EMERGENCY POWER FOR LAMPS
AC SPECS
120/347VAC
0.08/0.03 A
30MIN
1H00
1H30
2H00
4H00
10
-
6
-
-
ORDERING INFORMATION
SERIES
EFR2
COLOUR
WH= white
BK= black
BN= brushed nickel
CH= chrome
PB= polished brass
STANDARD
SP-C= Self-Powered
EXAMPLE: EFR2WHSP-C
103
LAMP WATTAGE
Blank= MR16, 6W
10= MR16,10W
Project/Location:
Distinction Series
Contractor:
™
Date:
Decorative 6, 12 and 24V
Prepared by:
TYPICAL SPECIFICATIONS
High performance and energy efficiency
in a contemporary design.
Supply and install the Emergi-Lite® Distinction™ Series battery units.
The battery unit will supply the rated load for a minimum of
hour to 87.5% of the rated battery/voltage. The unit shall be rated
120 or 347V, 60 Hz and be CSA No.141 listed. The charger shall be
fully computer tested and its charge voltage factory set to + or – 1%
tolerance. A pulse type charger shall be employed to promote long
battery life and reduce the potential for grid corrosion. The charger
shall provide continuous high charge to recharge the battery.
When the battery is at full capacity the charger will shut off. The
pulse charge shall be current limited and precisely regulated by
an electronic circuit which samples the battery in relation to its
temperature, state of charge and input voltage fluctuations. The
charger shall be current limited, temperature compensated,
short-circuit proof and reverse polarity protected.
The unit shall be furnished with an electronic lockout circuit, which
will connect the battery when the AC circuit is activated, and an
electronic brownout circuit, which will activate the emergency lights
when utility power dips below 75% of nominal voltage.
A low voltage battery protection circuit will disconnect the battery
at end of the discharge. The unit will come complete with the
Distinction™ Series diagnostics micro-controller board option. The
unit shall self-test for 1 minute every 30 days, 10 minutes on the 6th
month and 30 minutes every 12 months. The unit shall be furnished
with a sealed dust tight relay, a selectable test switch 1 minute, 5
minutes, 10 minutes or 20 minutes and diagnostics LED indicator
lights to continuously monitor the status of the unit: battery failed,
battery disconnect, charger failure, lamp failure, service alarm, AC
“ON” and charger “ON”.
The unit shall be Emergi-Lite® model:
.
The Distinction™ Series decorative battery units combine a
contemporary design with the latest in high-tech security
capability.
Designed to meet the needs of interior design professionals,
these battery units are also high performance and
energy-efficient.
FEATURES
• Rugged steel cabinet with corrosion-resistant undercoating
• Removable front panel on cabinet provides easy access and
allows unit to be mounted at ceiling height
• Solid-state pulse-type charger – current-limited,
temperature-compensated
• Unit comes standard with electronic lockout and
brownout circuits
• Sealed dust-proof transfer relay, test switch and LED
indicator lights continuously monitor unit status
• Long-life, maintenance-free lead acid battery
•NEXUS® compatible (for more information on NEXUS®,
please consult your sales representative)
• CSA C22.2 No. 141 certified
WIRE GUARDS
DIMENSIONS
460.0078-E
Wall Mount
“A” Cabinet
460.0081-E
Wall Mount
“B” Cabinet
460.0034-E
Wall Mount
“C” Cabinet
REPLACEMENT LAMPS
Dimensions are approximate and subject to change.
d
c
a
b
ORDERING CODE
LAMP TYPE
VOLTAGE/ WATTAGE
570.0074-E
MR16, halogen
6V-6W
570.0079-E
MR16, halogen
6V-10W
570.0080-E
MR16, halogen
12V-12W
570.0093-E
MR16, LED
12V-4W
570.0098-E
MR16, LED
24V-4W
570.0097-E
MR16, LED
6V-4W
570.0104-E
MR16, LED
12V-5W
570.0106-E
MR16, LED
12V-6W
For the complete list, please see the lamp chart on pages 156 to 158
CABINET
DIMENSIONS
A
B
C
D
A
13 1/4”
(33.7 cm)
3 5/8”
(9.2 cm)
10 1/2”
(26.7 cm)
14 1/4”
(36.2 cm)
B
16 1/8”
(40.9 cm)
5 1/2”
(13.9 cm)
10 1/4”
(26.0 cm)
13 7/8”
(35.2 cm)
C
23 1/8”
(58.7 cm)
5 1/2”
(13.9 cm)
10 1/4”
(26.0 cm)
13 7/8”
(35.2 cm)
104
Project/Location:
Distinction™ Series
Contractor:
Date:
Decorative 6, 12 and 24V
Prepared by:
POWER CONSUMPTION AND UNIT RATING
MODEL
WATTAGE CAPACITY
AC SPECS
30MIN
1H00
1H30
2H00
06ESL36
0.10/0.04 A
36
21
15
12
6
06ESL72
0.22/0.08 A
72
42
30
24
12
06ESL108
0.22/0.08 A
108
63
45
36
18
06ESL180
0.22/0.08 A
180
105
75
60
30
12ESL72
0.15/0.06 A
72
42
30
24
12
12ESL100
0.34/0.12 A
100
58
42
33
17
12ESL144
0.40/0.14 A
144
84
60
48
17
12ESL216
0.41/0.14 A
214
84
60
48
24
0.41/0.14 A
220
120
90
72
36
12ESL360
0.43/0.15 A
250
144
100
83
42
24ESL144
0.55 / 0.20 A
360
300
210
170
80
24ESL200
0.67 / 0.23 A
200
117
83
67
33
24ESL288
0.67 / 0.23 A
208
168
120
96
48
24ESL350
0.67 / 0.23 A
350
200
144
120
60
24ESL432
0.67 / 0.23 A
432
250
180
144
72
24ESL550
0.88 / 0.33 A
550
320
230
180
90
24ESL720
0.88 / 0.33 A
720
600
420
340
160
12ESL250
120/347VAC
4H00
* Note: Units provide higher power for minimum one hour of emergency lighting.
ORDERING INFORMATION
SERIES
CAPACITY
COLOUR
VOLTAGE
06ESL= 6V
36= 36W (A)
72= 72W (A)
108= 108W (A)
180= 180W (B)
Blank=
polar white
BK= black
12ESL= 12V
72= 72W (A)
100= 100W (A)
144= 144W (A)
216= 216W (B)
250= 250W (B)
360= 360W (B)
Blank=
120/347VAC
input
-2= 277VAC
input
24ESL= 24V
144= 144W (A)
200= 200W (B)
288= 288W (B)
350= 350W (C)
432= 432W (C)
550= 550W (C)
720= 720W (C)
OPTIONS
# OF HEADS
HEAD STYLE LAMP VOLTAGE-WATTAGE
EF150= closed
A= ammeter
/1= one head
CT= cab-tire
/2= two heads
D= time delay (programmable)
/3= three heads
LW= cord and twist-lock plug
(120V)
P= light activated test switch
T= lamp disconnect
TB= DC terminal block
TX2= remote test transmitter
U= auto-diagnostics*
UN= a
uto-diagnostics,
non-audible*
V= voltmeter
X2= remote test receiver**
NEX= NEXUS® system interface
(for 6V and 12V units
only)***
NEXRF= wireless NEXUS®
system interface***
FB6= 6 cct. fuse panel
TBACDC= AC/DC terminal block
TBAC= AC terminal block
* Minimum lamp load required: 20%
of unit capacity
**One remote test receiver per order
*** Not all options available with the
NEXUS® system. Please consult
your sales representative.
EXAMPLE: 06ESL108U/2EF150MJ
105
MI= MR16, 6V-6W
MJ= MR16, 6V-10W
MK= MR16, 12V-12W
MA= MR16, 12V-20W
MB= MR16, 12V-35W
MC= MR16, 12V-50W
MS= MR16, 24V-12W
MD= MR16, 24V-20W
ME= MR16, 24V-35W
MF= MR16, 24V-50W
LA= MR16 LED, 6V-4W
LG= MR16 LED, 12V-4W
LL= MR16 LED, 24V-4W
LI= MR16 LED, 12V-5W
LJ= MR16 LED, 12V-6W
Project/Location:
DEL Series
Contractor:
Decorative 6, 12 and 24V
Thermoplastic Cube Units
Date:
Prepared by:
TYPICAL SPECIFICATIONS
FEATURES
• Impact-resistant steel center cabinet contains the battery
and charger
Supply and install a complete emergency lighting system as
described herein and shown on the drawings.
The Emergi-Lite® DEL Smart Diagnostic micro-controller board
shall supply the rated load for a minimum of 1/2 hour to 87.5% of the
rated battery voltage. The unit shall be rated 120V or 347V, 60 Hz and
be CSA listed.
The unit shall have an output of
V.
The charger shall be fully computer tested and its charge voltage
factory set to ± 1% tolerance. Chargers with field-adjusted
potentiometers are not acceptable. A pulse-type charger shall be
employed to promote long battery life and reduce the potential for
grid corrosion. The charger shall provide a continuous high charge
to recharge the battery, and when the battery is at full capacity,
the charger will shut off. Periodically the charger shall provide a
pulse of energy to keep the battery topped off. The charger shall
be current limited, temperature compensated, short-circuit proof
and reverse polarity protected. The unit shall be furnished with an
electronic lockout circuit, which will connect the battery when the
AC circuit is activated, and an electronic brownout circuit, which will
activate the emergency heads when utility power dips below 75%
of nominal voltage. A low voltage battery protection circuit shall
be provided and will disconnect the battery from the fused output
circuit at the end of discharge. The unit shall self-test for 1 minute
every 30 days, 10 minutes every 6 months and 30 minutes every 12
months. The unit shall be capable of full recharge in compliance
with CSA specifications. The unit shall be furnished with a sealed,
dust-tight relay, a test switch and diagnostic LED indicator lights to
continuously monitor the status of the unit: Battery Failure, Battery
Disconnected, Charger Failure, Lamp Failure, Service Alarm, AC
-“ON”, Charger High Rate. The unit shall come complete with fully
adjustable 12V or 24V/12W or 20W quartz halogen lamps. Each lamp
shall be housed in an impact-resistant polycarbonate cube. The cube
lens shall be frosted to diffuse light.
The unit shall be Emergi-Lite® model:
.
• Frosted, thermoplastic light cubes protect light modules
against vandalism while providing visual masking and light
diffusion
• Units can be wall or ceiling mounted
• Maintenance-free, sealed Lead-Calcium battery
• Fully automatic, solid-state charger with low voltage battery
disconnect, brownout protection, integral test switch and
LED AC-On pilot lights
• Also available as a remote fixture; see the Remote Fixtures
section of this catalogue
• CSA C22.2 No. 141 certified
• NEXUS® compatible
WIRE GUARDS
460.0097-E
Wall Mount or Ceiling Mount
REPLACEMENT LAMPS
IN THE SAME FAMILY
EF26/EF26DS/EF26D SERIES
P. 151
ORDERING CODE
TYPE
570.0016-E
Mini tungsten
VOLTAGE/ WATTAGE
6V-9W
570.0025-E
Mini tungsten
12V-9W
570.0045-E
Mini tungsten
24V-9W
580.0097-E
MR16, LED
6V-4W
580.0093-E
MR16, LED
12V-4W
580.0104-E
MR16, LED
12V-5W
580.0098-E
MR16, LED
24V-4W
580.0095-E
MR16, LED
120V-4W
580.0106-E
MR16, LED
120V-4W
For the complete list, please see the lamp chart on pages 156 to 158
106
Project/Location:
DEL Series
Contractor:
Decorative 6, 12 and 24V
Thermoplastic Cube Units
Date:
Prepared by:
DIMENSIONS
Dimensions are approximate and subject to change.
303/4” [78.1 cm]
43/4” [12.1 cm]
43/4” [12.1 cm]
41/2” [11.4 cm]
217/8” [55.6 cm]
POWER CONSUMPTION AND UNIT RATING
MODEL
WATTAGE CAPACITY
AC SPECS
1H30
2H00
06DEL36
0.10/0.04 A
36
21
15
12
6
06DEL72
0.22/0.08 A
72
42
30
24
12
06DEL144
0.22/0.08 A
108
63
45
36
18
06DEL180
0.22/0.08 A
180
105
75
60
30
12DEL36
0.10/0.04 A
36
21
15
12
6
0.15/0.06 A
72
42
30
24
12
12DEL144
0.41/0.14 A
144
84
60
48
24
12DEL200
0.41/0.14 A
200
117
83
67
33
12DEL288
0.41/0.14 A
288
168
120
96
48
24DEL144
0.55/0.20 A
144
84
60
48
24
24DEL288
0.67/0.23 A
288
168
120
96
48
12DEL72
120/347VAC
30MIN
1H00
4H00
ORDERING INFORMATION
SERIES
CAPACITY
06DEL=
6V
36= 36W
72= 72W
144= 144W
180= 180W
12DEL=
12V
36= 36W
72= 72W
144= 144W
200= 200W
288= 288W
24DEL=
24V
144= 144W
288= 288W
VOLTAGE
Blank=
120/347VAC input
-2= 277VACinput
# OF
LAMPS
OPTIONS
D= time delay
L= line cord 120V
LW= cord and twist-lock plug 120V
T= lamp disconnect
TB= DC terminal block
TP= tamper-proof screws
U= auto-diagnostics*
UN= auto-diagnostics, non-audible*
X2= remote test receiver**
690.0454-E= tamper-proof bit***
TX2= remote test transmitter
NEX= NEXUS® system interface****
NEXRF= wireless NEXUS® system
interface****
* Minimum lamp load required: 20% of unit
capacity
**Remote test transmitter needed.
***One bit per order.
****Not all options available with the Nexus®
system. Please consult your sales
representative.
EXAMPLE: 06DEL36U/2
107
/2= t wo
lamps
LAMP STYLE/WATTAGE
Blank= tungsten, 6V, 12V, 24V-9W, wedge base
-18= tungsten, 12V, 24V-18W, wedge base
MI= MR16, 6V-6W
MJ= MR16, 6V-10W
MK= MR16, 12V-12W
MA= MR16, 12V-20W
MB= MR16, 12V-35W
MC= MR16, 12V-50W
MS= MR16, 24V-12W
MD= MR16, 24V-20W
ME= MR16, 24V-35W
MF= MR16, 24V-50W
Q= halogen, 6V, 12V-8W, quartz bi-pin
Q12= halogen, 6V, 12V-12W, quartz bi-pin
Q20= mini halogen, 6V,12V, 24V-20W, quartz bi-pin
LA= MR16 LED, 6V-4W
LG= MR16 LED, 12V-4W
LI= MR16 LED, 12V-5W
LL= MR16 LED, 24V-4W
LJ= MR16 LED, 12V-6W
Project/Location:
Contractor:
ESLT Series
Date:
Prepared by:
6, 12, 24V T-Bar Unit
TYPICAL SPECIFICATIONS
Fully recessed units for T-Bar mounting
in suspended ceilings.
Supply and install a complete emergency lighting system as
described herein and shown on the drawings.
The Emergi-Lite® Smart Diagnostic Micro controller board shall
supply the rated load for a minimum of a 30 minutes to 87.5% of the
rated battery voltage. The unit shall be rated 120V or 347V, 60 Hz and
be CSA listed. The unit shall have an output of
V.
The charger shall be fully computer tested and its charge voltage
factory set to ± 1% tolerance. Chargers with field-adjusted
potentiometers are not acceptable. A pulse-type charger shall be
employed to promote long battery life and reduce the potential for
grid corrosion. The charger shall provide a continuous high charge
to recharge the battery and when the battery is at full capacity, the
charger will shut off. Periodically the charger shall provide a pulse of
energy to keep the battery topped off. The charger shall be current
limited, temperature compensated, short-circuit proof and reverse
polarity protected. The unit shall be furnished with an electronic
lockout circuit, which will connect the battery when the AC circuit
is activated, and an electronic brownout circuit, which will activate
the emergency lights when utility power dips below 75% of nominal
voltage. A low voltage battery protection circuit shall be provided
and will disconnect the battery from the fused output circuit at
the end of discharge. The unit shall self-test for 1 minute every 30
days, 10 minutes every 6 months and 30 minutes every 12 months.
The unit shall be capable of full recharge in compliance with a CSA
specifications. The unit shall be furnished with a sealed dust tight
relay, a test switch and seven diagnostic LED indicator lights to
continuously monitor the status of the unit: Battery Failure, Battery
Disconnected, Charger Failure, Lamp Failure, Service Alarm, AC
“ON”, Charger High Rate. The unit shall be T-bar mounted and come
complete with tool-less emergency lighting heads requiring no tools
to adjust or aim.
The unit shall be Emergi-Lite® model:
.
The ESLT Series battery units are designed for T-bar ceiling
grid installation. This slim-line, unobtrusive unit is ideally suited
for any commercial location where there is limited wall space
and where the greater directional flexibility of ceiling-mounted
heads is needed to provide greater light distribution.
FEATURES
• Rugged steel cabinet with corrosion-resistant undercoating.
• Battery and charger are concealed above the ceiling level
in the unit cabinet
• Removable panel provides easy access to battery and
circuitry
• Test switch and LED indicators are mounted on the visible
bottom panel
• Units mount quickly and easily in standard 2’ x 2’ or 2’ x 4’
grids without any additional hardware
• Solid-state pulse-type charger – current-limited,
temperature-compensated, short-circuit proof and
reverse-polarity protected
• Unit comes standard with electronic lockout and brownout
circuits
• Sealed dust-proof transfer relay, test switch and LED
indicator lights
• Long-life, maintenance-free lead acid battery
• NEXUS® compatible (for more information on NEXUS®,
please consult your sales representative)
• CSA C22.2 No. 141 certified
REPLACEMENT LAMPS
CABINET
Large
Cabinet
Small
Cabinet
DIMENSIONS
A
B
C
D
E
F
23 3/4”
7 1/4”
7 1/8”
10 5/8”
5 5/8”
13”
(60.3 cm) (18.4 cm) (18.1 cm) (27.0 cm) (14.3cm) (33.0 cm)
7 1/4”
4 5/8”
10 5/8”
23 3/4”
(60.3 cm) (18.4 cm) (11.7 cm) (27.0 cm)
3 1/4”
(8.3 cm)
13”
(33.0 cm)
DIMENSIONS
ORDERING CODE
LAMP TYPE
VOLTAGE/WATTAGE
570.0016-E
Mini tungsten
6V-9W
570.0025-E
Mini tungsten
12V-9W
570.0045-E
Mini tungsten
24V-9W
580.0104-E
MR16, LED
12V-5W
580.0093-E
MR16, LED
12V-4W
580.00097-E
MR16, LED
6V-4W
580.00098-E
MR16, LED
24V-4W
580.0106-E
MR16, LED
12V-6W
For the complete list, please see the lamp chart on pages 156 to 158
Dimensions are approximate and subject to change.
e
a
b
d
f
c
108
Project/Location:
Contractor:
ESLT Series
Date:
Prepared by:
6, 12, 24V T-Bar Unit
POWER CONSUMPTION AND UNIT RATING
MODEL
WATTAGE CAPACITY
AC SPECS
30MIN
1H00
1H30
2H00
06ESLT36
0.10/0.04 A
36
21
15
12
4H00
6
06ESLT72
0.22/0.08 A
72
42
30
24
12
06ESLT108
0.22/0.08 A
108
63
45
36
18
06ESLT180
0.22/0.08 A
180
105
75
60
30
0.09/0.03 A
36
21
15
12
6
0.15/0.06 A
72
42
30
24
12
17
12ESLT36
12ESLT72
120/347VAC
12ESLT100
0.34/0.12 A
100
58
42
33
12ESLT144
0.40/0.14 A
144
84
60
48
24
12ESLT216
0.41/0.14 A
200
117
83
67
33
24ESLT144
0.55/0.20 A
144
84
60
48
24
24ESLT288
0.67/0.23 A
288
168
120
96
48
ORDERING INFORMATION
SERIES CAPACITY
06ESLT= 36= 36W
6V
72= 72W
108= 108W
180= 180W
12ESLT= 36= 36W
12V
72= 72W
100= 100W
144= 144W
216= 216W
24ESLT= 144= 144W
24V
288= 288W
COLOUR
Blank=
factory
white
BK= black
VOLTAGE
OPTIONS
A= ammeter
Blank=
120/347VAC input CT= cab-tire
-2= 277VAC input D= time delay
LW= twist-lock plug
T= lamp disconnect
(programmable)
FB6= 6 cct. fuse panel
TBACDC= AC/DC terminal
block
TBAC= AC terminal block
P= light activated test switch
TB= DC terminal block
TX2= remote test transmitter
U= auto-diagnostics*
UN= a
uto-diagnostics,
non-audible*
V= voltmeter
X2= remote test receiver**
NEX= NEXUS® system
interface***
NEXRF= wireless NEXUS®
system interface***
# OF HEADS
HEAD STYLE LAMP WATTAGE
/0= no heads
/1= one head
/2= two heads
/3= three
heads
Blank= large tungsten, 6V, 12V, 24V-9W,
wedge base
-18= large tungsten, 12V, 24V-18W, wedge base
-25= large tungsten, 6V, 12V, 24V-25W, DCB
M= mini tungsten, 6V, 12V, 24V-9W, wedge base
M18= mini tungsten, 12V, 24V-18W, wedge base
MQ= mini halogen, 6V, 12V-8W, quartz bi-pin
MQ12= mini halogen, 6V, 12V, 24V-12W,
quartz bi-pin
Q8= large halogen, 6V, 12V- 8W, quartz bi-pin
Q12= large halogen, 6V, 12V-12W, quartz bi-pin
Q20= large halogen, 6V, 12V, 24V-20W,
quartz bi-pin
Q55= large halogen, 12V-55W, quartz H3
Q70= large halogen 24V-70W, quartz H3
MI= MR16, 6V-6W
MJ= MR16, 6V-10W
MK= MR16, 12V-12W
MA= MR16, 12V-20W
MS= MR16, 24V-12W
S= large tungsten, 6V, 12V-8W, sealed beam
S18= large tungsten, 6V, 12V-18W, sealed beam
S25= large tungsten, 6V, 12V-25W, sealed beam
H= large halogen, 6V, 12V-8W, quartz sealed beam
H12= large halogen, 6V, 12V-12W,
quartz sealed beam
H20= large halogen, 6V-20W, quartz sealed beam
EF150MA= MR16 mini deco, 12V-20W*
EF150MB= MR16 mini deco, 12V-35W*
EF150MC= MR16 mini deco, 12V-50W*
EF150MD= MR16 mini deco, 24V-20W*
EF150ME= MR16 mini deco, 24V-35W*
LA= MR16 LED, 6V-4W
LG= MR16 LED, 12V-4W
LI= MR16 LED, 12V-5W
LL= MR16 LED, 24V-4W
LJ= MR16 LED, 12V-6W
EF150MF= MR16 mini-deco, 24V-50W
EF150MS= MR16 mini-deco, 4V-12W
* Minimum lamp load required: 20%
of unit capacity
**Remote test transmitter needed.
*** Not all options available
with the NEXUS® system.
Please consult your sales
representative.
EXAMPLE: 06ESLT108U/2MQ
109
*Aluminum head only
Project/Location:
WonderPack™ WP36
Series
Contractor:
Date:
Thermoplastic
Prepared by:
TYPICAL SPECIFICATIONS
FEATURES
• Injection-molded thermoplastic housing
The Contractor will install the Emergi-Lite® WonderPack™ WP36
Series battery unit.
The emergency lighting system shall consist of fully automatic
equipment with two MR16 glare-free halogen heads. Each unit shall
contain a fully automatic, solid state charger with test switch and
AC on pilot lights.
• Two adjustable glare-free light heads
• Test switch and charge rate indicators
• Emergency mode: min. 90 minutes
• Universal 120/347 VAC input
The unit shall contain a sealed transfer circuit and low voltage
disconnect circuit. The battery shall be 6V with a capacity of 29W for
30 minutes.
• CSA C22.2 No. 141 certified
• Innovative snap together design allows for fast installation
The unit shall be CSA C22.2 no 141.
The unit shall be Emergi-Lite® model:
.
WIRE GUARDS
460.0100-E
Wall Mount or Ceiling Mount
REPLACEMENT LAMPS
DIMENSIONS
ORDERING CODE
LAMP TYPE
VOLTAGE/ WATTAGE
580.0072-E
MR16
6V-6W
580.0079-E
MR16
6V-10W
Dimensions are approximate and subject to change.
41/8” [10.5 cm]
51/2” [14 cm]
121/8” [30.8 cm]
POWER CONSUMPTION AND UNIT RATING
MODEL
AC SPECS
DC SPECS
WP36/2M
120/347VAC
0.06/0.03 A
Less than 6W
6V-10.8W
Min. 90 minutes
WP36/2M10
120/347VAC
0.06/0.03 A
Less than 6W
6V-20W
Min. 30 minutes
ORDERING INFORMATION
SERIES
WP
CAPACITY
36= 6V-29W
VOLTAGE
Blank= 120/347VAC
# OF LAMPS AND TYPE
/2M= two MR16 lamps, 6V-5.4W (standard)
EXAMPLE: WP36/2M10
110
OPTION
Blank= no options
10= MR16 lamps, 10W
Project/Location:
Eclipse™ Series
Contractor:
Date:
Rapid Installation
Decorative Thermoplastic
Prepared by:
FEATURES
TYPICAL SPECIFICATIONS
• Impact-resistant thermoplastic construction
Supply and install the Emergi-Lite® Eclipse™ Series battery unit.
The unit shall come standard with housing and back plate of white
thermoplastic and two prismatic-shaped lenses made of clear
polycarbonate. The unit shall contain a fully automatic, solid-state
charger circuit with test switch button and AC-on LED pilot light. The
charger shall include features like brownout detection, low-battery
disconnect and instant transfer.
The unit shall be equipped with two incandescent emergency lamps
of 6V-5.4W and a maintenance-free Lead-Calcium battery with fiveyear life expectancy.
The total output for emergency lighting shall be 6V-29W for minimum
30 minutes.
The unit shall come standard with a DC-remote cable with in-line
fuse and provide 18W of remote capacity.
The unit shall be listed CSA C22.2 no.141
.
The unit shall be Emergi-Lite® model:
• Wall or ceiling mount
• Pre-wired AC quick-connect plug for fast and easy installation
• Dual-voltage input: 120/347 VAC
• Two wedge-base, incandescent lamps of 6V- 5.4W
• DC-remote fused output of 6V-18W
• Fully automatic, solid-state battery charger with brownout
protection, low-voltage battery disconnect, manual test switch
and LED pilot light
• Maintenance-free, sealed Lead-Calcium battery with life
expectancy of five years
• Listed CSA C22.2 No.141
REPLACEMENT LAMPS
ORDERING CODE
LAMP TYPE
VOLTAGE/ WATTAGE
570.0012-E
Tungsten, wedge base
6V-5.4W
WIRE GUARDS
460.0100-E
Wall Mount or Ceiling Mount
For the complete list, please see the lamp chart on pages 144 to 146
DIMENSIONS
Dimensions are approximate and subject to change.
12” [30.5 cm]
5” [12.6 cm]
23/4” [7 cm]
POWER CONSUMPTION AND UNIT RATING
MODEL
ECL-2
WATTAGE CAPACITY
AC SPECS
120/347VAC
0.06/0.02 A
30MIN
1H00
1H30
2H00
4H00
29W
17W
12W
10W
-
ORDERING INFORMATION
SERIES
ECL
UNIT CAPACITY
-2V= 6V-29W
VOLTAGE
Blank= 120/347VAC
EXAMPLE: ECL-2V
111
OPTIONS
Blank= no options
L= line cord (120V only)
Project/Location:
Contractor:
JMLC Series
Date:
Steel, compact, 6V and 12V
Prepared by:
FEATURES
TYPICAL SPECIFICATIONS
• Compact steel cabinet with corrosion-resistant undercoating
The contractor shall install the Emergi-Lite® JMLC Series battery
units. The emergency lighting system shall consist of fully automatic
equipment with two emergency lighting heads. The unit shall be
rated
V with a capacity of
W for 30 minutes of emergency
operation.
The charger shall be factory set with a charging voltage tolerance of
± 1% to enable a longer battery life. The emergency light heads shall
require no tools for adjusting or aiming. The metal cabinet shall be
made of steel with anti-corrosion undercoating.
The unit equipped with the auto-test micro-controller board shall
self-test 1 minute every 30 days, 10 minutes every 6 months and
30 minutes every 12 months. The unit shall be supplied with a test
switch and diagnostic LED indicator lights to continuously monitor
the status of the unit: Battery Failure, Battery Disconnect, Charger
Failure, Lamp Failure, Service Alarm, main voltage AC “ON”, Charger
High Rate.
The unit shall be CSA Certified to C22.2 no.141.
The unit shall be Emergi-Lite® model:
.
• Quick and easy installation – pre-assembled cordset, no
batteries or board to remove before installation
• Universal Spider knockout pattern for junction box mounting
• Fully automatic solid-state charger with test switch and
AC-on pilot light
• Sealed dust-proof transfer relay circuit and low-voltage
disconnect
• Long-life, maintenance-free sealed
• NEXUS® compatible. Please consult your sales
representative
• Heads require no tools for orientation
• Standard input 120 VAC with line cord installed
• 120/347 VAC without line cord
• Certified CSA C22.2 No.141
WIRE GUARDS
460.0080-E
Wall Mount
POWER CONSUMPTION AND UNIT RATING
MODEL
WATTAGE CAPACITY
AC SPECS
1H30
2H00
06JMLC27
0.06/0.02 A
27
15
11
9
-
06JMLC44
0.18/0.06 A
44
26
18
15
7
12
06JMLC72
120/347 VAC
30MIN
1H00
4H00
0.19/0.07 A
72
42
30
24
12JMLC44
0.31/0.10 A
44
26
18
15
7
12JMLC72
0.31/0.10 A
72
42
30
24
12
REPLACEMENT LAMPS
ORDERING CODE
LAMP TYPE
570.0012-E
Mini tungsten
6V-9W
570.0025-E
Mini tungsten
12V-9W
580.0097-E
MR16, LED
6V-4W
580.0093-E
MR16, LED
12V-4W
580.0104-E
MR16, LED
12V-5W
580.0106-E
MR16, LED
12V-6W
For the complete list, please see the lamp chart on pages 156 to 158
112
VOLTAGE/ WATTAGE
Project/Location:
Contractor:
JMLC Series
Date:
Prepared by:
Steel, compact, 6V and 12V
DIMENSIONS
91/8” [23.1 cm]
Dimensions are approximate and subject to change.
31/4” [8.4 cm]
123/4” [32.3 cm]
ORDERING INFORMATION
SERIES
CAPACITY
06JMLC = 6V
27= 27W*
44= 44W
72= 72W
12JMLC= 12V
44= 44W
72= 72W
COLOUR
Blank=
factory white
BK= black
VOLTAGE
Blank= 1
20VAC
c/w
linecord
-2= 277VAC input
-3= 120/347VAC
input
OPTIONS
# OF HEADS
HEADS STYLE/WATTAGE
Blank= no options
CT= cab-tire
LW= twist-lock plug
U= auto-diagnostics*
UN= auto-diagnostics,
non-audible*
NEX= N
EXUS® system
interface**
NEXRF= w
ireless
NEXUS®
system
interface**
/0= no heads
/1= one head
/2= two heads
Blank= large tungsten, 6V, 12V-9W, wedge base
-18= large tungsten, 12V-18W, wedge base
-25= large tungsten, 6V, 12V-25W, DCB
H= large halogen, 6V, 12V-8W, quartz sealed
beam
H12= large halogen, 6V, 12V-12W, quartz sealed
beam
H20= large halogen, 6V-20W, quartz sealed beam
M= mini tungsten, 6V, 12V-9W, wedge base
M18= mini tungsten, 12V-18W, wedge base
MQ= mini halogen, 6V, 12V-8W, quartz bi-pin
MQ12= mini halogen, 6V, 12V, 24V-12W,
quartz bi-pin
MI= MR16, 6V-6W
MJ= MR16, 6V-10W
MK= MR16, 12V-12W
MA= MR16, 12V-20W
Q= large halogen, 6V, 12V-8W, quartz bi-pin
Q12= large halogen, 6V, 12V-12W, quartz bi-pin
Q20= large halogen, 6V, 12V, 24V-20W, quartz
bi-pin
S= large tungsten, 6V, 12V-9W, sealed beam
S18= large tungsten, 6V, 12V-18W, sealed beam
S25= large tungsten, 6V, 12V-25W, sealed beam
LA= MR16 LED, 6V-4W
LG= MR16 LED, 12V-4W
LI= MR16 LED, 12V-5W
LJ= MR16 LED , 12V-6W
*6V-72W available in ESL
series only.
*Not available
in 12V
**Consult your sales
representative - not
available in 6V-72W.
EXAMPLE: 06JMLC44/2M
113
Project/Location:
Contractor:
JMLA Series
Date:
Decorative, 6 and 12V
Prepared by:
FEATURES
TYPICAL SPECIFICATIONS
Supply and install the Emergi-Lite® JMLA Series battery units.
• Rugged steel cabinet with corrosion-resistant undercoating
The battery unit shall come complete with two MR16 emergency
lighting heads. The unit shall be rated for dual voltage120/347V,
60 Hz and shall provide power to the nominal load for at least 30
minutes to 87.5% of the nominal voltage of the battery. The charger
shall be factory set with a charging voltage tolerance of ±1% to
enable a longer battery life. The emergency light heads shall be fully
adjustable and protected by a clear cover, made of shock-resistant
polycarbonate. The protective cover shall be designed to facilitate
lamp replacement. The heads shall be installed at the bottom of
the unit, providing illumination in any downward direction. The
emergency light heads shall require no tools for orientation. The
unit cabinet shall be made of steel with anti-corrosion undercoating.
The unit equipped with the auto-test diagnostic micro-controller
board shall self-test 1 minute every 30 days, 10 minutes the every 6
months and 30 minutes every 12 months. The unit shall be supplied
with a test switch and diagnostic LED indicator lights to continuously
monitor the status of the unit: Battery Failure, Battery Disconnect,
Charger Failure, Lamp Failure, Service Alarm, main voltage AC “ON”,
Charger High Rate.
The unit shall be CSA Certified to C22.2 no.141.
The unit shall be Emergi-Lite® model:
.
• Removable front panel on cabinet provides easy access and
allows unit to be mounted at ceiling height
• Solid-state pulse-type charger – current-limited,
temperature-compensated, short-circuit proof and reversepolarity protected
• Unit comes standard with electronic lockout and brownout circuits
• Sealed dust-proof transfer relay, test switch and LED indicator
light(s)
• Long-life, maintenance-free lead acid battery
• NEXUS® compatible. Please consult your sales representative
• CSA C22.2 No. 141 Certified
DIMENSIONS
Dimensions are approximate and subject to change.
33/8” [8.6 cm]
123/4” [32.4 cm]
9” [22.9 cm]
REPLACEMENT LAMPS
WIRE GUARDS
460.0080-E
Wall Mount
POWER CONSUMPTION AND UNIT RATING
MODEL
ORDERING CODE
LAMP TYPE
VOLTAGE/ WATTAGE
580.0074-E
MR16
6V-6W
580.0079-E
MR16
6V-10W
580.0080-E
MR16
12V-12W
580.0068-E
MR16
12V-20W
580.0097-E
MR16 LED
6V-4W
580.0093-E
MR16 LED
12V-4W
580.0104-E
MR16 LED
12V-5W
580.0106-E
MR16 LED
12V-6W
WATTAGE CAPACITY
AC SPECS
1H30
2H00
06JMLA27
0.06/0.02 A
27
15
11
9
-
06JMLA44
0.18/0.06 A
44
26
18
15
7
12
06JMLA72
30MIN
1H00
4H00
0.19/0.07 A
72
42
30
24
12JMLA44
0.31/0.10 A
44
26
18
15
7
12JMLA72
0.31/0.10 A
72
42
30
24
12
120/347VAC
ORDERING INFORMATION
SERIES
CAPACITY
06JMLA= 6V
27= 27W*
44= 44W
72= 72W
12JMLA= 12V
44= 44W
72= 72W
COLOUR
VOLTAGE
OPTIONS
Blank= f actory
white
BK= black
Blank= 120/347VAC
-2= 277VAC input
Blank= no options
CT= cab-tire
LC= linecord (120V)
LW= twist-lock plug
U= auto-diagnostics*
UN= a
uto-diagnostics,
non-audible*
NEX= NEXUS® system interface**
NEXRF= wireless NEXUS® system
interface**
* Minimum lamp load required: 20% of
unit capacity
* Not available in 12V
** Consult your sales representative,
not available in 6V-72W. 6V-72W
available in ESL
EXAMPLE: 12JMLA44UN/2MW
114
# OF HEADS HEADS STYLE/WATTAGE
/2= 2 heads
LA= MR16 LED, 6V-4W
LG= MR16 LED, 12V-4W
LI= MR16 LED, 12V-5W
LJ= MR16 LED, 12V-6W
MI= MR16, 6V-6W
MJ= MR16, 6V-10W
MK= MR16, 12V-12W
MW= MR16-IR, 12V-20W
Project/Location:
JEM18P Series
Contractor:
Date:
Compact Emergency Lighting Units
Prepared by:
FEATURES
TYPICAL SPECIFICATIONS
• Compact emergency lighting unit available in factory white
The contractor will install the Emergi-Lite® JEM18P Series
compact emergency lighting unit. The unit housing shall be made of
injection moulded, high impact, corrosion resistant thermoplastic.
The unit dimensions including the emergency heads shall be less
than 24.1cm x 17.1cm x 12.4cm. The unit shall be rated 120VAC
60Hz input and 6VDC nominal output. The unit shall contain a fully
automatic, solid-state battery charger with test switch and AC-on
pilot light. The charger shall be computer tested and shall contain
low-voltage disconnect circuitry to protect the battery from deep
discharge. The battery shall be maintenance-free, sealed leadcalcium and shall supply the emergency heads with power for
minimum 60 minutes during an AC power failure.
• Fully automatic, solid state, voltage sensitive charger with test
switch and AC-on pilot light
• Sealed dust-proof transfer relay circuit and low voltage
disconnect
• Long-life, maintenance-free sealed Lead-Calcium battery
• Housing and heads constructed of injection molded, high impact,
corrosion resistant thermoplastic
• 120VAC standard input
• 60 minutes run time
The unit shall include two emergency heads built of
flame-retardant thermoplastic and shall include two mini-tungsten
6V-9W lamps.
• CSA C22.2 No. 141 certified
The unit shall be CSA C22.2 no 141.
The unit shall be Emergi-Lite® Model:
.
DIMENSIONS
Dimensions are approximate and subject to change.
91/2” [24.1 cm]
63/4” [17.1 cm]
WIRE GUARDS
460.0082-E
Wall Mount or Ceiling Mount
REPLACEMENT LAMPS
97/8” [24.4 cm]
ORDERING CODE
LAMP TYPE
VOLTAGE/WATTAGE
570.0016-E
Mini tungsten
6V-9W
ORDERING INFORMATION
SERIES
JEM= compact plastic
CAPACITY
18P= 18W
LAMP
Blank= 6V-9W
EXAMPLE: JEM18P
115
COLOUR
Blank= factory white
VOLTAGE
Blank= 120VAC input
Project/Location:
Contractor:
Premier™ Series
Date:
Thermoplastic, 6 and 12V
Prepared by:
FEATURES
TYPICAL SPECIFICATIONS
• Designed with aesthetics, ease of installation and performance
in mind
Supply and install the Emergi-Lite® Premier™ Series battery unit
equipment. The unit construction shall include a housing and a front
cover of high-impact thermoplastic moulded in white. No screws
shall be necessary to hold the front cover to the housing. The unit
shall be equipped with two emergency heads with adjustable swivels
and MR-16 lamps of
V
W protected by snap-on shockabsorbent, clear polycarbonate covers. The unit shall be suitable for
wall mount or as otherwise specified.
The unit equipment shall have a dual-voltage input of 120/347VAC
and shall be equipped with a test switch and a green pilot light,
located on the left side. The housing shall host the battery and the
battery charger. The battery charger and other unit functions shall be
driven by a micro-controller. All electronic circuitry shall be installed
on a single printed circuit board.
When specified, the unit equipped with auto-test shall automatically
self-test for one minute every 30 days, 10 minutes every 6 months
and 30 minutes annually. When a fault is detected, the bi-colour pilot
light shall turn from green to red and start flashing. A legend on a
label next to the pilot light shall display the source of failure: battery,
charger circuitry or lamp load.
The unit equipment shall be listed to the standard CSA 22.2 No.141.
.
The unit equipment shall be Emergi-Lite® model:
• Simple, compact and contemporary design
• Wall-mount, ceiling-mount flat or pendant installation
• Two-piece housing of injection-molded thermoplastic
• Two MR16 halogen lamps, shielded by clear polycarbonate covers
• Available with long lasting MR16 LED lamps
• Sealed, maintenance-free, Lead-Calcium battery
• Dual voltage input: 120/347VAC.
• Up to 150W of total battery capacity
• Auto-diagnostics (optional)
• NEXUS® interface (optional)
• Certified CSA 22.2 No.141
WIRE GUARDS
460.0114-E
Wall Mount or flat ceiling mount
REPLACEMENT LAMPS
ORDERING CODE
LAMP TYPE
580.0079-E
MR16 halogen
VOLTAGE/ WATTAGE
6V-10W
580.0080-E
MR16 halogen
12V-12W
580.0064-E
MR16 halogen
12V-20W
580.0093-E
MR16 LED
12V-4W
580.0097-E
MR16 LED
6V-4W
580.0104-E
MR16 LED
12V-5W
580.0106-E
MR16 LED
12V-6W
PREMIER™ FAMILY
116
Premier™ Combo Series
Premier™ Exit Series
P. 56-57
P. 55
Project/Location:
Contractor:
Premier™ Series
Date:
Prepared by:
Thermoplastic, 6 and 12V
DIMENSIONS
Dimensions are approximate and subject to change.
105/8” [26.9 cm]
121/4” [31.0 cm]
37/8” [9.8 cm]
FLAT CEILING MOUNT
POWER CONSUMPTION AND UNIT RATING
MODEL
WATTAGE CAPACITY
AC SPECS
30MIN
1H00
1H30
2H00
PRE40
40
23
16
12
-
PRE72
72
42
30
24
12
12PRE80
120/347VAC
0.25 / 0.09 A
4H00
80
44
32
26
13
12PRE120
120
70
50
40
20
12PRE150
150
84
60
48
24
ORDERING INFORMATION
SERIES
06PRE= 6V
CAPACITY
40= 40W
72= 72W
12PRE= 12V 80= 80W
120= 120W
150= 150W
COLOUR
VOLTAGE
W= factory
white
B= black
Blank=
120/347VAC
2= 120/277VAC
UNIT TYPE
Blank= standard
U= auto-diagnostics*
UN= a
uto-diagnostics
non-audible*
NEX= NEXUS® system
interface**
NEXRF= N
EXUS® wireless
system interface**
* Minimum lamp load required: 20%
of unit capacity
** Not all options are available with
the Nexus® system. Please consult
your sales representative
EXAMPLE: 06PRE40W/2MI
117
OPTIONS
Blank= no options
CM= ceiling mount
D3= time delay
(15 minutes)
LC= line cord (120V)
PM= pendant mount
HEADS
/0= no
heads
/2= two
heads
LAMPS
LA= MR16 LED, 6V-4W
LG= MR16 LED,
12V-4W
LI= MR16 LED,
12V-5W
LJ= MR16 LED,
12V-6W
MI= MR16, 6V-6W
MJ= MR16, 6V-10W
MK= MR16, 12V-12W
MW= MR16-IR,
12V-20W
Project/Location:
Contractor:
ESL Series
Date:
6, 12 and 24V
Prepared by:
TYPICAL SPECIFICATIONS
10-year life expectancy, maintenance-free
emergency lighting units.
Supply and install a complete emergency lighting system as
described herein and shown on the drawings.
The Emergi-Lite® Smart Diagnostic micro-controller board shall
supply the rated load for a minimum of a 1/2 hour to 87.5% of the
rated battery voltage. The unit shall be rated 120V or 347V, 60 Hz and
be CSA listed. The unit shall have an output of:
V
and
W.
The charger shall be fully computer tested and its charge voltage
factory set to ± 1% tolerance. Chargers with field-adjusted
potentiometers are not acceptable. A pulse-type charger shall be
employed to promote long battery life and reduce the potential for
grid corrosion. The charger shall provide a continuous high charge
to recharge the battery, and when the battery is at full capacity, the
charger will shut off.
Periodically the charger shall provide a pulse of energy to keep the
battery topped off. The pulse charger shall be precisely regulated
and shall charge the battery in relation to its temperature, state or
charge and input voltage fluctuations. The charger shall be current
limited, temperature compensated, short-circuit proof and reverse
polarity protected.
The unit shall be furnished with an electronic lockout circuit, which
will connect the battery when the AC circuit is activated, and an
electronic brownout circuit, which will activate the emergency lights
when utility power dips below 75% of nominal voltage. A low voltage
battery protection circuit shall be provided and will disconnect the
load when the battery reaches the end of discharge. The unit shall
self-test for 1 minute every 30 days, 10 minutes every 6 months
and 30 minutes every 12 months. The unit shall be capable of full
recharge in compliance with CSA specifications. The unit shall be
furnished with a sealed dust tight relay, a test switch and diagnostic
LED indicator lights to continuously monitor the status of the unit:
Battery Failure, Battery Disconnected, Charger Failure, Lamp
Failure, Service Alarm, AC “ON”, Charger High Rate. The emergency
lighting heads shall require no tools for orientation.
The unit shall be Emergi-Lite® model:
.
The ESL Series battery units combine long life expectancy,
high-performance design and a reasonable initial cost outlay.
Ideally suited for a range of commercial applications, the long-life
lead acid battery is specifically recommended for environments
where the unit will be exposed to large variances in ambient
temperature.
FEATURES
• Rugged steel cabinet with corrosion-resistant undercoating
• Removable front panel on cabinet provides easy access and
allows the unit to be mounted at ceiling height
• Solid-state pulse-type charger – current-limited, temperaturecompensated, short-circuit proof and reverse-polarity protected.
• Unit comes standard with electronic lockout and brownout
circuits
• Sealed dust-proof transfer relay, test switch and LED indicator
lights
• Long-life, maintenance-free lead acid battery
• NEXUS® compatible (for more information on NEXUS®, please
consult your sales representative)
• CSA C22.2 No. 141 certified
• Standard 120/347 VAC input with line cord kit
DIMENSIONS
CABINET
A
B
C
D
E
A
13 1/4“
(33.7 cm)
3 5/8“
(9.2 cm)
10 1/2“
(26.7 cm)
14 1/4“
(36.2 cm)
16 1/2“
(41.9 cm)
B
16 1/8“
(40.9 cm)
5 1/2“
(13.9 cm)
10 1/4“
(26.0 cm)
13 7/8“
(35.2 cm)
16 1/8“
(41.0 cm)
23 1/8“
(58.7 cm)
5 1/2“
(13.9 cm)
10 1/4“
(26.0 cm)
13 7/8“
(35.2 cm)
16 1/8“
(41.0 cm)
C
WIRE GUARDS
Wall Mount
“A” Cabinet
460.0081-E
Wall Mount
“B” Cabinet
460.0034-E
Wall Mount
“C” Cabinet
REPLACEMENT LAMPS
DIMENSIONS
Dimensions are approximate and subject to change.
d
c
a
460.0078-E
e
ORDERING CODE
LAMP TYPE
VOLTAGE/WATTAGE
570.0016-E
Mini tungsten (MT9W)
6V-9W
570.0025-E
Mini tungsten (MT9W)
12V-9W
570.0045-E
Mini tungsten (MT9W)
24V-9W
580.0093-E
MR16 LED
12V-4W
580.0104-E
MR16 LED
12V-5W
580.0098-E
MR16 LED
24V-4W
580.0106-E
MR16 LED
12V-6W
For the complete list, please see the lamp chart on pages 156 to 158
b
118
Project/Location:
Contractor:
ESL Series
Date:
Prepared by:
6, 12 and 24V
POWER CONSUMPTION AND UNIT RATING
MODEL
WATTAGE CAPACITY
AC SPECS
30 MIN
1H00
1H30
2H00
06ESL36
0.10/0.04 A
36
21
15
12
4H00
6
06ESL72
0.22/0.08 A
72
42
30
24
12
06ESL108
0.22/0.08 A
108
63
45
36
18
06ESL180
0.22/0.08 A
180
105
75
60
30
12ESL36
0.09/0.03 A
36
21
15
12
6
12ESL72
0.15/0.06 A
72
42
30
24
12
12ESL100
0.34/0.12 A
100
58
42
33
17
12ESL144
0.40/0.14 A
144
84
60
48
24
12ESL216
12ESL250
120/347VAC
0.41/0.14 A
216
117
83
67
33
0.41/0.14 A
250
144
100
38
42
12ESL360
0.41/0.14 A
360
200
144
108
60
24ESL144
0.43/0.15 A
144
84
60
48
24
24ESL200
0.55 / 0.20 A
200
117
83
67
33
24ESL288
0.67 / 0.23 A
288
168
120
96
48
24ESL350
0.67 / 0.23 A
350
200
144
120
60
24ESL432
0.67 / 0.23 A
432
250
180
144
72
24ESL550
0.88 / 0.33 A
550
320
230
180
90
24ESL720
0.88 / 0.33 A
720
420
300
240
120
Note: Low wattage LED lamps provide extended time of emergency lighting without additional power.
ORDERING INFORMATION
SERIES
CAPACITY
06ESL= 6V
36= 36W (A)
72= 72W (A)
108= 108W (A)
180= 180W (B)
12ESL= 12V
36= 36W (A)
72= 72W (A)
100= 100W (A)
144= 144W (A)
216= 216W (B)
250= 250W (B)
360= 360W (C)
24ESL= 24V
144= 144W (A)
200= 200W (B)
288= 288W (B)
350= 350W (C)
432= 432W (C)
550= 550W (C)
720= 720W (C)
COLOUR
VOLTAGE
Blank= 1
Blank=
20/347VAC
factory
input
white
-2= 277VAC input
BK= black
OPTIONS
A= ammeter
CT= cab-tire
D= time delay
LW= cord and twist-lock
plug 120V
P= light activated test
switch
T= lamp disconnect
TB= DC terminal block
TBAC= AC terminal block
TX2= remote test
transmitter
U= auto-diagnostics*
UN= auto-diagnostics
non-audible*
V= voltmeter
X2= remote test receiver**
FB6= 6 circuit fuse panel
NEX= NEXUS® system
interface***
NEXRF= wireless
NEXUS® system
interface***
TBACDC= AC/DC terminal
block
*M
inimum lamp load required:
20% of unit capacity
** Remote test transmitter
needed.
***Not all options available with
NEXUS®. Consult your sales
representative.
EXAMPLE: 06ESL108U/2M
119
# OF HEADS
HEADS STYLE/WATTAGE
/0= no heads
/1= one head
/2= two heads
/3= three
heads
Blank= large tungsten, 6V, 12V, 24V-9W, wedge
base
-18= large tungsten, 12V, 24V-18W, wedge base
-25= large tungsten, 6V, 12V, 24V-25W, DCB
LA= MR16 LED, 6V-4W
LG= MR16 LED, 12V-4W
LL= MR16 LED, 24V-4W
LI= MR16 LED, 12V-5W
LJ= MR16 LED, 12V-6W
H= large halogen, 6V, 12V-8W, quartz sealed
beam
H12= large halogen, 6V, 12V-12W, quartz sealed
beam
H20= large halogen, 6V-20W, quartz sealed beam
M= mini tungsten, 6V, 12V, 24V-9W, wedge base
M18= mini tungsten, 12V, 24V-18W, wedge base
MQ= mini halogen, 6V, 12V-8W, quartz bi-pin
MQ12= mini halogen, 6V, 12V, 24V-12W,
quartz bi-pin
MI= MR16, 6V-6W
MJ= MR16, 6V-10W
MK= MR16, 12V-12W
MN= MR16, 24V-20W
MA= MR16, 12V-20W
MS= MR16, 24V-12W
MW= 12V-20W, high-output
Q= large halogen, 6V, 12V-8W, quartz bi-pin
Q12= large halogen, 6V, 12V-12W, quartz bi-pin
Q20= large halogen, 6V, 12V, 24V-20W, quartz
bi-pin
Q55= large halogen, 12V-55W, quartz H3
Q70= large halogen 24V-70W, quartz H3
S= large tungsten, 6V, 12V-8W, sealed beam
S18= large tungsten, 6V, 12V-18W, sealed beam
S25= large tungsten, 6V, 12V-25W, sealed beam
Project/Location:
Survive-All™ NXM
Series
Contractor:
Date:
Prepared by:
NEMA-4X Certified
TYPICAL SPECIFICATIONS
FEATURES
• Fully gasketed cast aluminum back plate with clear
polycarbonate cover – NEMA-4X Certified
Supply and install the Emergi-Lite® NEMA-4X Certified
Survive-All™ NXM Series battery unit. Specifically designed for high
abuse areas, wet locations, and cold weather (CW option -40°C
(-40°F)), the housing shall consist of a fully gasketed Die-Cast with
a cast aluminum back plate and a clear heavy-duty UV resistant
polycarbonate cover. The heads shall be fully adjustable without
tools and the lamps shall be high efficiency halogen MR16. The
standard unit shall be equipped with tamper-proof screws and bits.
The Emergi-Lite® Advanced Diagnostic Micro-controller charger
board shall supply the rated load for a minimum of 30 minutes to
87.5% of the rated battery voltage. The charger incorporates lockout
and brownout circuits, and low voltage disconnection. It protects the
unit from over-current, short-circuit, and reverse polarity. The unit
shall be rated 120/347V, 60Hz. The unit shall have an output of
V. This unit shall self-test for 1 minute every 30 days, 10 minutes
every 6 months and 30 minutes every 12 months. The unit shall
be furnished with a non-intrusive magnetic test switch. A “Service
Required” lamp shall be located near the test switch and flash when
a fault is detected. A four-LED diagnostic display shall be located
inside the equipment and shall identify the source of failure (battery,
charger, circuitry, or lamps).
• Comes standard with non-audible advanced diagnostic,
10 minutes time delay and lamp disconnect
• Audible warning and time delay functions can be enabled
or disabled during installation
• Micro-controller diagnostic system tests, detects and
indicates battery, charger circuitry or MR16 lamp failures
• Non-intrusive magnetic test switch
• Long-life, maintenance-free sealed lead-acid battery
• 1/2” rigid conduit entry on top and back
• Can be installed on 4” junction boxes
• Comes standard with tamper-proof screws and bit
• Cold weather option -40ºC (-40ºF)
• NSF Certified for food processing plants
• CSA C22.2 No. 141 Certified
• NEXUS® compatible
The unit shall be Emergi-Lite® model:
• Standard 120/347VAC input voltage
WIRE GUARDS
460.0031-E
Wall Mount
REPLACEMENT LAMPS
NEMA-4X
ORDERING CODE
LAMP TYPE
580.0074-E
MR16 halogen
VOLTAGE/ WATTAGE
6V-6W
580.0079-E
MR16 halogen
6V-10W
580.0080-E
MR16 halogen
12V-12W
580.0064-E
MR16 halogen
12V-20W
580.0104-E
MR16 LED
12V-5W
580.0097-E
MR16 LED
6V-4W
580.0106-E
MR16 LED
12V-6W
SURVIVE-ALL™ NEMA 4X & NSF CERTIFIED FAMILY
120
ENC SERIES
LPEX600
SERIES
LPEX600-N
SERIES
EN SERIES
EF39 SERIES
P. 62
P. 61
P. 63
P.112-113
P.136
Project/Location:
Survive-All™ NXM
Series
Contractor:
Date:
Prepared by:
NEMA-4X Certified
DIMENSIONS
Dimensions are approximate and subject to change.
53/4” [14.6 cm]
173/4” [45.1 cm]
7” [17.8 cm]
PMK KIT
(SCREWS INCLUDED)
SUPERSTRUT
MOUNTING
BEAM MOUNTING
POWER CONSUMPTION AND UNIT RATING
MODEL
WATTAGE CAPACITY
AC SPECS
06NXM36
0.15/0.06 A
12NXM72
120/347VAC
12NXM108
Cold Weather 36W
Cold Weather 72/108W
120VAC
30MIN
1H00
1H30
2H00
4H00
36
21
15
12
6
0.25/0.10 A
72
42
30
24
12
0.25/0.10 A
108
63
45
36
18
0.45/0.20 A
36
-
-
-
-
0.85 A
72/108
-
-
-
-
*Note: capacity depends on the ambient temperature
ORDERING INFORMATION
SERIES
06NXM= 6
V,
NEMA-4X
12NXM= 1
2V,
NEMA-4X
COLOUR
W= white
BK= black
G= grey
CAPACITY
36= 6V-36W
72= 12V-72W
108= 12V-108W
VOLTAGE
Blank= 120/347VAC
2= 277VAC
OPTIONS
Blank= no options
CW1= cold weather 120VAC
CW3= cold weather 347VAC*
NEX= N
EXUS® system
interface**
NEXRF= wireless NEXUS®
system interface**
PMK-E= universal bracket
(sold separetely)
690.0454-E= additional-bit for
tamper-proof
screws
(sold separately)
*Available in 6V only.
**Consult your sales representative for
options available with the NEXUS®
system.
EXAMPLE: 06NXMW36/2MI
121
# OF HEADS
/2= 2 heads
LAMP
LA= MR16 LED,
6V-4W*
LG= MR16 LED,
12V-4W*
LI= MR16 LED,
12V-5W
LJ= MR16 LED,
12V-6W
MI= MR16, 6V-6W
MJ= MR16, 6V-10W
MK= MR16,
12V-12W
MG= MR16,
12V-20W*
MW= MR16-IR,
12V-20W
*Minimum lamp load
required: 20% of unit
capacity
Project/Location:
IPE Series
Contractor:
Date:
IP65 Linear
Fluorescent Fixture
Prepared by:
TYPICAL SPECIFICATIONS
FEATURES
• IP65 rated
Supply and install Emergi-Lite® IPE Series fluorescent fixtures as
specified. The luminaire shall operate from 120VAC to 277VAC or
347VAC and use high quality instant start or 3-step programmed
rapid start high efficiency electronic ballasts.
The body and lens shall be constructed of UV stabilized industrial
grade vandal-resistant polycarbonate. A durable formed gasket
shall be provided between the enclosure and the lens and shall
be designed specifically for hostile environments. The reflector
shall be made of highly specular material and formed to maximize
light output efficiency. All parts shall be corrosion resistant. A
metal plate used to retain the ballast and reflector also serves to
dissipate heat, therefore lengthening ballast life.
Lamps shall be as specified, either T8 or T5 HO linear fluorescent
lamps, 32W or 54W. The lamps shall not be supplied with the
luminaire. Models with an inverter from the FPSI/FPSU Series
shall illuminate one or two lamps during emergency operation for
at least 90 minutes upon AC failure. During power outage, dual
voltage source (AC/DC) models with an inverter from the 48 Series
shall illuminate one lamp while the DC voltage is present.
The fixture shall be CSA approved and meet IP65 designation
requirements.
The inverters of Series 48 shall be CSA approved.
The inverters of the FPS Series shall be CSA or cUL approved.
The fixture shall be Emergi-Lite® model: __________________
• Polycarbonate enclosure and lens, vandal resistant and UV
stabilized
• Rust proof hardware
• Ceiling, surface or pendant mounting
• Low profile, less than 4” deep
• Ultra efficient specular reflector with optimized shape
• 32W T8 or 54W T5HO
• 90 minutes of emergency operation when installed with our FPSI
or FPSU inverters
• Emergency operation from external DC low voltage power source
when installed with our 48 Series inverters
• Suitable for wet locations
• CSA certified to CSA-E60598-1: 02
DIMENSIONS
Dimensions are approximate and subject to change.
63/4” [17 cm]
503/4” [129 cm]
WIRE GUARDS
33/4” [10 cm]
460.0105-E
Wall Mount or Ceiling Mount
POWER CONSUMPTION
MODEL
36” [91 cm]
AC SPECS
IPE8
120/277VAC
0.54/0.23 A
PF > 0.9
IPE83
347VAC
0.19 A
PF > 0.9
IPE5
120/277VAC
1.03/0.143 A
PF > 0.9
IPE53
347VAC
0.35 A
PF > 0.9
ORDERING INFORMATION
SERIES
IPE= 48” (122cm)
linear fluorescent
LAMP TYPE*
8= 2x lamps 32W T8
5= 2x lamps 54W T5HO
VOLTAGE
ACCESSORIES
Blank= AC only
120/277VAC
3= AC only 347VAC
DC= 120VAC/VDC
Self-powered, one lamp emergency
FPSI-32= inverter for IPE8 (complete code = IPE8FPSI-32)
FPSI⁄U-3= inverter for IPE8-3 (complete code = IPE8-3FPSI⁄U-3)
FPSI⁄U= inverter for IPE5 (complete code= IPE5FPSI⁄U)
Self-powered, two lamps emergency
FPSU-28= inverter for IPE8 (complete code= IPE8FPSU-28)
FPSI⁄U-3= inverter for IPE8-3 (complete code= IPE8-3FPSI⁄U-3)
4806100= 6V, 120VAC
4806100-3= 6V, 347VAC
4812100= 12V, 120VAC
4812100-3= 12V, 347VAC
4824100= 24V, 120VAC
4824100-3= 24V, 347VAC
081282-E= Stainless Steel Clips Kit (10)
Lamps not included
EXAMPLE: IPE8
122
4832100= 32V, 120VAC
4832100-3= 32V, 347VAC
4848100= 48V, 120VAC
4848100-3= 48V, 347VAC
48120100= 120V, 120VAC
48120100-3= 120V, 347VAC
Project/Location:
SIPE Series
Contractor:
Date:
IP65 Linear 2’
Fluorescent Fixture
Prepared by:
FEATURES
TYPICAL SPECIFICATIONS
Supply and install Emergi-Lite® SIPE Series fluorescent fixtures as
specified.
The luminaire shall operate from 120VAC to 277VAC or 347VAC and
use high quality instant start or 3-step programmed rapid start high
efficiency electronic ballasts.
The body and lens shall be constructed of UV stabilized industrial
grade vandal resistant polycarbonate. A durable formed gasket
shall be provided between the enclosure and the lens and shall be
designed specifically for hostile environments. The reflector shall
be made of highly specular material and formed to maximize light
output efficiency. All parts shall be corrosion resistant. A metal plate
used to retain the ballast and reflector also serves to dissipate heat,
therefore lengthening ballast life.
Lamps shall be as specified, either T8 or T5 HO linear fluorescent
lamps, 17W or 24W. The lamps shall not be supplied with the
luminaire.
Models with an inverter from the FPS/48 Series will illuminate one
or two lamps during emergency operation for at least 90 minutes
upon AC failure. During power outage, dual voltage source (AC/DC)
models with an inverter from the 48 Series shall illuminate one lamp
while the DC voltage is present. The fixture shall be CSA approved
and meet IP65 designation requirements.
The inverters of 48 Series shall be CSA approved.
The inverters of the FPS Series shall be CSA or cUL approved.
• Normally On fluorescent fixture
• IP65 rated
• Polycarbonate enclosure and lens, vandal resistant and UV
stabilized
• Rust proof hardware
• Ceiling, surface or pendant mounting
• Low profile, less than 4” deep
• Ultra efficient specular reflector with optimized shape
• 17W T8 or 24W T5HO
• High efficiency and reliable electronic ballast
• 120VAC to 277VAC universal and 347VAC input voltage available
• CSA certified to CAN/CSA-E60598-1:02
• Certified for wet and damp locations
• Certified for AC or DC, 120V operations
INPUT RATING
ORDERING CODE
SIPE8
SIPE5
INPUT
CURRENT
120 - 277/347VAC
0.47/0.20/0.1 A
120VDC
0.3 A
120 - 277/347VAC
0.5/0.22 A
The fixture shall be Emergi-Lite® model: __________________
WIRE GUARDS
460.0106-E
Wall Mount or Ceiling Mount
DIMENSIONS
Dimensions are approximate and subject to change.
33/4” [10 cm]
63/4” [17 cm]
185/8” [47 cm]
263/8” [67 cm]
ORDERING INFORMATION
SERIES
SIPE= vapour proof 24”
LAMP TYPE*
8= 2 F17T8 17W T8 lamps
5= 2 T5HO 24W T5 lamps
*Lamps not included
EXAMPLE: SIPE8
123
VOLTAGE
Blank= 120/277VAC
3= AC only 347VAC
DC= 120/277VAC/VDC
Project/Location:
ESLPK Series
Contractor:
Date:
6, 12 and 24V
NEMA-12 Classified
Harsh environment emergency lighting
units with steel, thermoplastic or
fiberglass cabinets.
Prepared by:
TYPICAL SPECIFICATIONS
Supply and install a complete emergency lighting system as
described herein and shown on the drawings. The Emergi-Lite®
Smart Diagnostic Micro controller board shall supply the rated load
for a minimum of a 1/2 hour to 87.5% of the rated battery voltage.
The unit shall be rated 120V or 347V, 60 Hz and be CSA listed. The
unit shall have an output of
V. The charger shall be fully
computer tested and its charge voltage factory set to ± 1% tolerance.
Chargers with field-adjusted potentiometers are not acceptable. A
pulse-type charger shall be employed to promote long battery life
and reduce the potential for grid corrosion. The charger shall provide
a continuous high charge to recharge the battery and when the
battery is at full capacity, the charger will shut off. Periodically the
charger shall provide a pulse of energy to keep the battery topped
off. The Pulse charge shall be current limited and precisely regulated
by a micro-processing circuit, which samples the battery in relation
to its temperature, state or charge and input voltage fluctuations.
The charger shall be current limited, temperature compensated,
short-circuit proof and reverse polarity protected. The unit shall be
furnished with an electronic lockout circuit, which will connect the
battery when the AC circuit is activated, and an electronic brownout
circuit, which will activate the emergency lights when utility power
dips below 75% of nominal voltage. A low voltage battery protection
circuit shall be provided and will disconnect the battery from the
fused output circuit at the end of discharge. The unit shall selftest for 1 minute every 30 days, 10 minutes every 6 months and 30
minutes every 12 months. The unit shall be capable of full recharge
in compliance with CSA specifications. The unit shall be furnished
with a sealed dust tight relay, a test switch and diagnostic LED
indicator lights to continuously monitor the status of the unit: Battery
Failure, Battery Disconnected, Charger Failure, Lamp Failure,
Service Alarm, AC “ON”, Charger High Rate.
The unit shall be Emergi-Lite® model:
.
The ESLPK Series battery units are specifically designed for
use in industrial facilities where equipment is exposed to dust,
water, oil or corrosive substances. NEMA-12 classified to
protect circuitry from harmful dust or liquid sprays, sealed and
gasketed unit cabinets are available in steel, thermoplastic or
fiberglass in a variety of sizes.
FEATURES
• Solid-state pulse-type charger – current-limited,
temperature compensated, short-circuit proof and reversepolarity protected.
•Unit comes standard with electronic lockout and brownout
circuits
•Sealed dust-proof transfer relay, test switch and LED
indicator lights
• Long-life, maintenance-free sealed lead acid battery
• NEXUS® compatible (for more information on NEXUS®,
please consult your sales representative)
• CSA C22.2 No. 141 certified
• Standard 120/347 VAC input with line cord kit
DIMENSIONS
Dimensions are approximate and subject to change.
CABINET SIZE 1
WIRE GUARDS
d
460.0034-E
e
DIMENSIONS
CABINET
b
Wall Mount
A
B
C
D
E
F
Size 1
13”
5”
103/8”
1215/16”
8”
115⁄8”
Thermoplastic [29.5 cm] (33.0 cm) (12.7 cm) (26.4 cm) (32.8 cm) (20.3 cm)
f
a
c
CABINET SIZE 2, 3, 4 & 5
b
a
f
153/8”
63/4”
21”
143/4”
81/8”
131/4”
(33.8 cm) (38.9 cm) (17.0 cm) (53.3 cm) (37.5 cm) (20.6 cm)
Size 3 Fiberglass
241/4”
91/4”
303/8”
163/8”
(41.5 cm) (61.5 cm) (23.4 cm) (77.3 cm)
-
-
Size 4 Steel
57/8”
191/2”
121/8”
1315/16”
13”
131/4”
(33.0 cm) (33.8 cm) (14.8 cm) (49.6 cm) (30.8 cm) (35.3 cm)
Size 5 Steel
261/4”
16”
20”
91/8”
(40.6 cm) (50.8 cm) (23.3 cm) (66.7 cm)
-
-
REPLACEMENT LAMPS
d
e
Size 2 Fiberglass
c
124
MODEL
LAMP TYPE
570.0016-E
Mini-Tungsten (LH9W)
VOLTAGE/WATTAGE
6V-9W
570.0025-E
Mini-Tungsten (LH9W)
12V-9W
570.0045-E
Mini-Tungsten (LH9W)
24V-9W
Project/Location:
ESLPK Series
Contractor:
Date:
6, 12 and 24V
NEMA-12 Classified
Prepared by:
POWER CONSUMPTION AND UNIT RATING
MODEL
WATTAGE CAPACITY
AC SPECS
1H30
2H00
06ESLK36
0.10/0.04A
36
21
15
12
6
06ESLK72
0.22/0.08A
72
42
30
24
12
06ESLK108
0.22/0.08A
108
63
45
36
18
06ESLK180
0.22/0.08A
180
105
75
60
30
12ESLK36
0.09/0.03A
36
21
15
12
6
12ESLK72
0.15/0.06A
72
42
30
24
12
12ESLK100
0.34/0.12A
100
58
42
33
17
12ESLK144
0.40/0.14A
144
84
60
48
24
0.41/0.14A
200
117
83
67
33
12ESLK250
0.41/0.14A
250
144
100
83
42
12ESLK360
0.43/0.15A
360
200
144
108
60
24ESLK144
0.55/0.20A
144
84
60
48
24
24ESLK288
0.67/0.23A
288
168
120
96
48
24ESLK350
0.67/0.23A
350
200
144
120
60
24ESLK432
0.67/0.23A
432
250
180
144
72
24ESLK550
0.88/0.33A
550
320
230
180
90
24ESLK720
0.88/0.33A
720
400
288
216
120
12ESLK200
120/347VAC
30MIN
1H00
4H00
ORDERING INFORMATION
SERIES
HOUSING
06ESL=
6V
K= metal
PK= P
VC/
fiberglass
CAPACITY AND
CABINET SIZE
36= 36W
72= 72W
108= 108W
180= 180W
12ESL=
12V
36= 36W
72= 72W
100= 100W
144= 144W
200= 200W
250= 250W
360= 360W
24ESL=
24V
144= 144W
288= 288W
350= 350W
432= 432W
550= 550W
720= 720W
VOLTAGE
OPTIONS
Blank=
120/347VAC
input
-2= 277VAC
input
A= ammeter
D= time delay
(programmable)
L= line cord (120V only)
LW= twist-lock plug
P= light activated test
switch
T= lamp disconnect
TX2= remote test
transmitter
TBAC= AC terminal block
TB= DC terminal block
U= auto-diagnostics*
UN= a
uto-diagnostics,
non-audible*
V= voltmeter
X2= remote test
receiver**
NEX= NEXUS® system
interface***
NEXRF= w
ireless
NEXUS® system
interface***
* Minimum lamp load
required: 20% of unit
capacity
** Remote test transmitter
needed.
***Not all options available
with NEXUS®. Consult
your sales representative.
EXAMPLE: 06ESLPK362H
125
# OF
HEADS
/0= n
o
heads
/1= o
ne
head
/2= t wo
heads
HEAD STYLE/LAMP WATTAGE
OPTIONS
Blank= large tungsten, 6V, 12V, 24V9W, wedge base
-18= large tungsten, 12V, 24V-18W,
wedge base
-25= large halogen, 6V, 12V-25W, DCB
Q8= large halogen, 6V, 12V- 8W, quartz
bi-pin
Q12= large halogen, 6V, 12V-12W,
quartz bi-pin
Q20= large halogen, 6V, 12V, 24V-20W,
quartz bi-pin
Q55= large halogen, 12V-55W, quartz
H3
Q70= large halogen 24V-70W, quartz
H3
S= large tungsten, 6V, 12V-8W, sealed
beam
S18= large tungsten, 6V, 12V-18W,
sealed beam
S25= large tungsten, 6V, 12V-25W,
sealed beam
H= large halogen, 6V, 12V-8W, quartz
sealed beam
H12= large halogen, 6V, 12V-12W,
quartz sealed beam
H20= large halogen, 6V-20W, quartz
sealed beam
RS= large rubber, tungsten, 6V-9W,
sealed beam
RS18=large rubber, tungsten, 6V,
12V-18W, sealed beam
RS25= large rubber, tungsten, 6V,
12V-25W, sealed beam
RH= large rubber, halogen, 6V, 12V-8W,
sealed beam
RH12= large rubber, halogen, 6V,
12V-12W, sealed beam
RH20= large halogen, 6V-20W, sealed
beam
FP= f ood
processing
lens
*For details,
consult
your sales
representatives.
Project/Location:
Contractor:
HZM Series
Date:
Hazardous Location Battery Unit
Prepared by:
TYPICAL SPECIFICATIONS
FEATURES
• Certified Class I Zone 2, Groups IIA, IIB and IIC
Supply and install Emergi-Lite® HZM Series battery units. Designed
specifically for Hazardous Location environments, the equipment
frame shall be of industrial grade polymeric material with gaskets
around both sides of the contour. The frame shall be fixed between
two plates made of 1/8” thick aluminum sheet. The back plate
shall include four keyholes for wall-mount installation. The front
plate shall include two water-tight lenses for pilot lights: AC-on
and “Service required”. When specified, the equipment shall have
attached a lower compartment containing two emergency lights with
adjustable swivels and MR-16 halogen lamps. The lamps shall be
shielded by a cast aluminum housing and protected by a shockabsorbent, transparent polycarbonate cover.
The equipment shall be certified for Hazardous Locations: Class
I Division 2 Groups A, B, C and D. The standard equipment shall
have a dual voltage input: 120/347VAC and shall be equipped with a
magnetic test switch located on the left side of the frame.
The unit shall include self-testing/self-diagnostic functions
monitored by a micro-controller and shall automatically self test for
one minute every 30 days, 10 minutes every 6 months and 30 minutes
annually. The “Service required” LED shall light when a fault is
detected. A four-LED diagnostic display located inside the equipment
shall identify the source of the failure (battery, charger circuitry, lamp
load).
The unit shall be listed CSA C22.2 No.141 and No. 137 – M1984
The battery unit shall be Emergi-Lite® model:
.
• Certified Class I Division 2, Groups A, B, C and D as per CSA C22.2
No.137-M1981
• Certified temperature codes for several types of emergency lamps
• Suited for areas with the risk of flammable gases, vapors or
liquids that can create an explosive atmosphere
• Certified CSA C22.2 No141
• Polymeric frame, with built-in gasket to prevent water infiltration
• Heavy-duty 1/8” thick aluminum back plate with keyholes for
secure wall-mount installation
• Two MR16 halogen or LED lamps, shielded by a cast aluminum
housing and a polycarbonate cover
• Sealed, maintenance-free, Lead-Calcium batteries with up to
120W emergency power
• Built-in microcontroller-based battery charger and
auto-diagnostics circuitry
• ½” electrical conduit entry on both sides and at the top
• NEXUS® compatible (for more information on NEXUS®, please
contact your sales representative)
TEMPERATURE CODES
LAMP RATING TEMP. CODE MAX. TEMP. REPLACEMENT PART
6V-10W
T3C
160°C (320°F)
580.0079-E
12V-12W
T3A
180°C (356°F)
580.0080-E
12V-20W
T2D
215°C (419°F)
580.0068-E
Note: Use qualified replacement lamps to avoid risk of over-heating.
POWER CONSUMPTION AND UNIT RATING
MODEL
HZM36
WATTAGE CAPACITY
AC SPECS
120/347VAC
0.15/0.06 A
30MIN
1H00
1H30
2H00
4H00
36
21
15
12
-
HZM72
120/347VAC
0.30/0.10 A
72
42
30
24
12
HZM120
120/347VAC
0.30/0.10 A
120
70
50
40
20
HZM150
120/347VAC
0.30/0.10 A
150
-
72
-
-
126
Project/Location:
Contractor:
HZM Series
Date:
Hazardous Location Battery Unit
Prepared by:
DIMENSIONS
Dimensions are approximate and subject to change.
31/2” [8.7 cm]
141/2” [36.8 cm]
61/4” [15.9 cm]
125/8” [32.1 cm]
133/4” [34.9 cm]
ORDERING INFORMATION
SERIES
06HZM= 6V
12HZM= 12V
CAPACITY
36= 6V-36W
72= 12V-72W
120= 12V-120W
150= 12V-150W
COLOUR
Blank= grey
AC VOLTAGE
Blank=
120/347VAC
-2= 277VAC
OPTIONS
U= auto-diagnostics, audible*
UN= auto-diagnostics
(non-audible)*
NEX= NEXUS® system interface**
NEXRF= wireless NEXUS® system
interface**
* Minimum lamp load required: 20% of unit
capacity
** Consult your sales representative for
options available with the NEXUS® system.
EXAMPLE: 06HZM36UN/2MJ
127
# OF HEADS
/0= no heads
/2= 2 heads
LAMP/WATTAGE
MJ= MR16, 6V-10W
MK= MR16, 12V-12W
MW= MR16-IR, 12V-20W
LA= MR16 LED, 6V-4W
LG= MR16 LED, 12V-4W
LI= MR16 LED, 12V-5W
Project/Location:
ESLNX Series
6, 12 and 24V
NEMA-4X Rated
FEATURES
•Solid-state pulse-type charger – current – limited, temperaturecompensated, short-circuit proof and reverse-polarity protected
•Unit comes standard with electronic lockout and brownout
circuits
•Sealed dust-proof transfer relay, test switch and LED indicator
lights
•Long-life, maintenance-free sealed lead acid battery
•Standard 120/347VAC input voltage with line cord kit
•NEXUS® compatible (for more information on NEXUS®,please
consult your sales representative)
• Certified CSA C22.2 No. 141
POWER CONSUMPTION AND UNIT RATING
06ESLNX72
WATTAGE CAPACITY
30MIN 1H00 1H30 2H00 4H00
72
06ESLNX108
0.22/0.08 A
06ESLNX180
42
30
24
12
108
63
45
36
18
180
105
75
60
30
12ESLNX72
0.15/0.06 A
72
42
30
24
12
12ESLNX100
0.34/0.12 A
100
58
42
33
17
0.40/0.14 A
144
84
60
48
24
0.41/0.14 A
200
117
83
67
33
0.41/0.14 A
250
120
90
83
42
12ESLNX360
0.41/0.14 A
360
200
160
120
60
24ESLNX144
0.55 / 0.20 A
144
84
60
48
24
24ESLNX288
0.67 / 0.23 A
288
168
120
96
48
24ESLNX350
0.67 / 0.23 A
350
200
144
120
60
24ESLNX432
0.67 / 0.23 A
432
250
180
140
72
12ESLNX144
12ESLNX200
120/347
VAC
12ESLNX250
The unit shall be rated 120V or 347V, 60 Hz and shall have an
output of: __ V __ W.
The unit shall be Emergi-Lite® model: _______________________.
WIRE GUARDS
460.0034-E
Prepared by:
Supply and install the Emergi-Lite® NEMA-4X Rated ESLNX Series
battery unit. The unit shall be specifically designed for high abuse
areas and wet locations. The unit enclosure shall be of
fiberglass-reinforced polyester and shall include a hinged door,
fully gasketed and locked with two corrosion-resistant screws. The
emergency head(s) shall be installed at the bottom of the unit and/
or at both sides and shall be covered by a UV-resistant polycarbonate
cover. The bottom head shall include one or two lamps as specified.
The unit shall come with two heads at the sides, each with one
MR16 lamp. The lamps shall be high-efficiency, long-life halogen or
LED type of: __V __W as specified. The lamp swivels shall be easily
adjustable without tools. The unit enclosure shall include a test
switch and a pilot light. The unit shall include sealed,
maintenance-free Lead-Calcium batteries and an electronic module
for the battery charger and other emergency lighting functions. The
charger shall be computer-tested and its maximum charge voltage
set in the factory with ± 1% tolerance.
A pulse-type charger shall be employed to promote long battery
life and reduce the potential for grid corrosion. The charger shall
provide a continuous high charge to recharge the battery and when
the battery is at full capacity, the charger will shut off. Periodically
the charger shall provide a pulse of energy to keep the battery topped
off. The charger shall be current limited, temperature compensated
and short-circuit proof. The unit shall be furnished with an electronic
lockout circuit, which will connect the battery when the AC circuit
is activated, and an electronic brownout circuit, which will activate
the emergency lights when utility power dips below 75% of nominal
voltage. A low voltage battery protection circuit shall be provided and
will disconnect the battery from the fused output circuit at the end of
discharge. When specified, the unit equipped with the
Emergi-Lite® Auto-Diagnostic feature shall include a microcontroller based charger board that will generate an automatic
test for 1 minute every 30 days, 10 minutes every six months and 30
minutes every 12 months.
The micro-controller circuitry shall ensure equipment readiness
and reliability by continuously monitoring every critical function of
the unit. If a component failure occurs, the pilot light located on the
front of the unit will change color from green to red and will flash
indicating a fault. A detailed diagnostic legend shall be available next
to the pilot light and shall provide fault identification (battery, charger
circuitry, lamps) for maintenance personnel.The unit shall be capable
of full recharge in compliance with CSA specifications and supply the
rated load for a minimum of a 1/2 hour to 87.5% of the rated battery
voltage.
•Fully gasketed fiberglass reinforced polyester housing - NEMA 4X
AC SPECS
Date:
TYPICAL SPECIFICATIONS
•Delivers great pathway illumination up to 70 feet, center to center
(with M20WH lamp)
MODEL
Contractor:
Wall Mount
128
Project/Location:
ESLNX Series
Contractor:
Date:
6, 12 and 24V
NEMA-4X Rated
Prepared by:
DIMENSIONS
Dimensions are approximate and subject to change.
131/4” [33.7 cm]
61/4” [15.9 cm]
185/8” [47.3 cm]
131/4” [33.7 cm]
ORDERING INFORMATION
SERIES
HOUSING
06ESL= 6V
NX=
NEMA-4X
12ESL= 12V
NX=
NEMA-4X
24ESL= 24V
NX=
NEMA-4X
CAPACITY
AC VOLTAGE
OPTIONS
# OF HEADS
72= 72W
108= 108W
180= 180W
72= 72W
100= 100W
144= 144W
200= 200W
250= 250W
360= 360W-30min/
160W-90min
144= 144W
288= 288W
350= 350W
432= 432W
Blank= 120/347
VAC input
-2= 277VAC input
Blank= no options
D1= time delay (5 minutes)
D2= time delay (10 minutes)
D3= time delay (15 minutes)
TB= DC terminal block
U= auto-diagnostics*
UN= auto-diagnostics non audible*
NEX= NEXUS® system interface
(6, 12 and 24V)**
NEXRF= wireless NEXUS® system
interface**
/0= no heads
/1= single head bottom
one lamp
/2= double head bottom
two lamps
/S= no head bottom with
single lamp on each
side
/1S= single head bottom
with single lamp on
each side
/2S= double head bottom
with single lamps
on each side
*Minimum lamp load required: 20% of
unit capacity
EXAMPLE: 06ESLNX72/BDLA
** N
ot all options available with NEXUS®.
Please consult your sales
representative.
129
LAMPS
MI= MR16, 6V-6W
MJ= MR16, 6V-10W
MK= MR16, 12V-12W
MA= MR16, 12V-20W
MD= MR16, 24V-20W
MS= MR16, 24V-12W
MW= 12V-20W, High output
LG= LED, 12V-4W
LA= LED, 6V-4W
LI= LED, 12V-5W
LJ= LED, 12V-6W
LL= LED, 24V-4W
Project/Location:
48 Series &
FPS Series
Contractor:
Date:
Prepared by:
Fluorescent Inverters
FEATURES
TYPICAL SPECIFICATIONS
•All FPS Series are fully load tested prior to shipment
48 Series: The electrical contractor shall supply and install
Emergi-Lite® 48 Series remote fluorescent inverter ballasts for
each fixture as shown on plans. The inverter shall operate on
VDC input for
minutes during a power failure.
The fluorescent lamp shall be maintained at
% lumen
output for one lamp only. The inverter is to be connected to the
remote battery unit as shown on plans (battery unit to be selected
according to voltage/wattage and duration required). The inverter
shall be capable of illuminating the fluorescent lamp even when it
is burned out under normal AC operation.
•Inverter is 100% solid state, short and open circuit proof
•Polarized DC input (48 Series only)
•120VAC 60Hz input is standard, 277 and 347VAC available as
options
•25%, 50% or 80% lamp lumen output
•Mounts directly in ballast channel, remote or optional
T-Bar fixture
•CSA listed
FPS Series: The electrical contractor shall supply and install
Emergi-Lite® FPS Series fluorescent inverters for each fixture
as shown on plans. The FPS Series inverter shall operate for
minutes during a power failure. The fluorescent lamp
shall be maintained at
% of nominal lumen output.
The FPS Series inverter shall be capable of illuminating the
fluorescent lamp even when it is out under normal AC operations.
.
DIMENSIONS
Dimensions are approximate and subject to change.
INTERNAL ENCLOSURE (BLACK)
71/4”
[18.4 cm]
23/4”
[7 cm]
151/4” [38.7 cm]
R ENCLOSURE (WHITE)
48 ENCLOSURE (WHITE) - INTERNAL
11/2” [3.8 cm]
41/2”
[11.4 cm]
207/8” [53 cm]
95/8” [24.4 cm]
VOLTAGE
SERIES
OUTPUT %
LUMENS
W
Blank= 120VAC
-2= 277VAC
-3= 347VAC
FPS-800
25
800
10
FPS-1600
50
1600
20
FPS-3200
80
2560
32
LUMENS / (%) FOR 48” TUBE
25= 25% (800 lumens)
Lumen outputs based on averages.
60= 50% (1600 lumens)
24”/20W=1260 48”/40W=3200
96”/75W=6300
100= 80% (2560 lumens)
Inverters will operate T12, T8, or “U”
type lamps.
21/2”
[6.4 cm]
D.C. POWER CONSUMPTION
ORDERING INFORMATION 48 SERIES
4806= 6V
4812= 12V
4824= 24V
4832= 32V
4848= 48V
48120= 120V
45/8”
[11.7 cm]
233/4” [60.3 cm]
3” [7.6 cm]
48 SERIES
31/4”
[8.3 cm]
T ENCLOSURE (FACTORY WHITE)
11/2” [3.8 cm]
EXAMPLE: 4812-25-3
ORDERING INFORMATION FPS SERIES
SERIES
FPS
LUMENS / (%) FOR 48” TUBE
25= 25% (800 lumens)
Lumen outputs based on averages.
60= 50% (1600 lumens)
24”/20W=1260 48”/40W=3200 96”/75W=6300
100= 80% (2560 lumens)
Inverters will operate T12, T8, or “U” type lamps.
MIN. RUNTIME
HOUSING
30= 30 minutes
60= 60 minutes
90= 90 minutes
120= 120 minutes*
Blank= internal*
R= remote mounting enclosure
T= T-Bar
*FPS100 in T-Bar cabinet only.
*Not available for FPS100.
EXAMPLE: FPS60/30
130
AC VOLTAGE
Blank= 120VAC
-2= 277VAC
-3= 347VAC
Project/Location:
Contractor:
Date:
Prepared by:
Glossary
A
Ammeter
Used to measure the current being supplied to the battery while in charge mode.
U
Auto-Diagnostics
Automatically tests and continuously monitors your emergency lighting unit. If a problem occurs, the unit will send a
visual (flashing or blinking LED indicator) and audible warning. Complies with Fire Code requirements.
UN
Auto-Diagnostics,
non-audible
Automatically tests and continuously monitors your emergency lighting unit. If a problem occurs, the unit will send a
visual (flashing or blinking LED indicator) warning. Complies with Fire Code requirements.
CT
Cab-tire
Unit supplied with a cab-tire cable used for special hardwire applications.
CW1
Cold weather, 120VAC
120VAC input cold weather protection feature for applications where temperatures can reach -40° C.
CW3
Cold weather, 347VAC
347VAC input cold weather protection feature for applications where temperatures can reach -40° C.
FB6
6cct. Fuse panel
Panel used to facilitate the connection of multiple input load circuits in high power battery units.
TX2
Remote test transmiter
Used to preform maintenance tests by means of radio transmitter along with a radio receiver (RRT option) on battery
units that are out of reach.
H
Heater & thermostat
Like a heat blanket, used to keep internal temperature optimal for battery units that are installed in cold environments.
L
Line cord (120V)
When ordering a battery unit with the LC option, we supply and pre-install a line cord with a standard 3 prong 120V plug.
Just hang the fixture and plug it in to a standard receptacle! Only available on 120V units.
T
Lamp disconnect
To disconnect the emergency lighting load in an area that is not in use during a prolonged power failure or while the
area is no longer being occupied.
P
Light activated
test switch
Used to remotely test battery units by pointing a flashlight at a photocell mounted on the bottom of a battery unit.
FP
Teflon coated lens
A protective teflon coating that is applied to the glass lens of a lighting fixture to prevent broken shards from falling in
the event the glass is accidently broken or vandalised.
X2
Remote test receiver
Used to preform maintenance tests by means of radio reciever in conjunction with a transmitter (HHC option) on battery
units that are out of reach. Simply point the receiver at the unit
NEX
NEXUS® system interface
The NEXUS® system interface is a computerized maintenance system for emergency lighting that, once programmed,
will perform the tests, keep written records and send notification if anything needs to be fixed. One full system can
address hundreds of units in as many buildings as you need from a single location.
NEXRF
NEXUS® wireless system
interface
The NEXUS® wireless system interface is a computerized maintenance system for emergency lighting that, once
programmed, will perform the tests, keep written records and send notification if anything needs to be fixed. One full
system can address hundreds of units in as many buildings as you need from a single location.
15 minutes time delay
Normally, when the A.C. is restored, all emergency lighting lamps are turned off. However, in some cases such as
when metal halide lamps are used, it is possible that the general lighting will not be available for several minutes after
the blackout (or brownout) period. Battery units with the T3 option will keep some energy in store to ensure that the
emergency lighting stays on or comes back on for at least 15 minutes once the regular A.C. power has been restored.
Time delay
Same as the T3 option but can be programmed for 5, 10, 15 or 20 minutes delay.
TP
Tamper-proof screws
Screws that require a special bit. Can be used on certain units to deny access to unauthorized personnel.
LW
Twistlock plug
Used to facilitate the connection and removal of battery units for maintenance purposes.
AC/DC terminal block
Used to facilitate the connection of large gauge input cables.
TB
DC terminal block
Used to facilitate the connection of large gauge D.C. input cables.
TBAC
AC terminal block
Used to facilitate the connection of large gauge A.C. input cables.
Voltmeter
Indicates voltage being supplied to the battery when in charge mode.
D3
D
TBACDC
V
131
SURVIVE-ALL
DISTINCTION
EF9
RETRACT
-A-LITE
LITRAY
EF40
PROVIDER
LUX
-RAY
EFXPR
REMOTE
FIXTURES
133
Project/Location:
Contractor:
TABLE OF CONTENTS
Date:
Prepared by:
Project/Location:
MR16 LED EMERGENCY LIGHTING
Contractor:
Date:
Prepared by:
MR16 LED ILLUMINATION
MR16 LED LAMP BENEFITS
With the remarkable technology development in the last
decade, the light-emitting diode (LED) is becoming the
preferred solution in low- and medium-power lighting
applications. The emergency lighting industry is no
exception: today virtually every new product introduced to
market includes “white” LEDs for emergency illumination.
• CSA C22.2 No. 141 certified.
• Energy-efficient LED MR16 lamp provides equivalent
lighting performance to a much higher watt halogen
MR16 lamp.
• Reduces required battery capacity by 75%, providing
necessary illumination with fewer remote heads and
battery units for project cost savings.
Extremely efficient and long-lasting, LED lamps become the
natural alternative to incandescent lamps due to three main
advantages:
• Small profile, compact white lighting is ideal for
architectural applications.
• = lamp efficacy: 50 - 70 lumen per watt compared to 15 30 lumen per watt of the best halogen lamp.
• Vibration-resistant LED stands up to industrial
environments.
• = operational life: 30,000+ hours, equivalent to a lifetime
warranty in emergency lighting.
• Ideal for indoor and outdoor use.
• = lower lamp temperature (80 - 120°C) is a huge benefit
for lighting in hazardous locations.
340-LUMEN 5W MR16 LED
200-LUMEN 4W MR16 LED
Keeping pace with technology, in 2012 we introduced a
12V-5W MR16 LED lamp. With a typical luminous flux of 340
lumens, this lamp has the same lighting performance as
a 20W high-output halogen MR16. A twin emergency head
installed at a height of 7.5ft illuminates more than a 70ft
path of egress.
Leading the technology trend, Emergi-Lite® offers a
complete series of 4W MR16 LED lamps available for all
the standard battery voltages: 6V, 12V, 24V and 120V. With
up to 30,000 hours of operational life and a luminous
flux of typically 200 lumens, they are available with most
emergency heads designed to hold an MR16 lamp and meet
the majority of illumination specifications. For example: one
pair of LED emergency heads installed at a height of 7.5ft,
illuminates a 6ft by 40ft path of egress.
510-LUMEN 6W MR16 LED
New in Fall 2013, we intoduce a 12V - 6W MR16 LED lamp,
which offer typical luminous flux of 510 lumens. Like the
lower wattage MR16 LED lamps, this new lamp is specially
designed for emergency lighting. It offers the same lighting
preformance as the 35W or 20W Mr16 IR. A twin emergency
head installed at a height of 7.5’ illuminates approximately
100’ path of egress.
Compared to halogen lamps (16-20W), these 4W MR16
LED lamps illuminate the same area of egress during an
emergency situation by using 75% less power. This has
a direct impact on the battery size, reducing the back-up
capacity needs by 75%. Consequently, it also reduces the
total cost of the application, with the use of smaller battery
capacity units, the possibility of using fewer fixtures due to
superior illumination, thus also reducing electrical wiring,
and it it reduces the environmental footprint.
40-FT. PATH OF EGRESS 2 X 4W MR16 LED
70-FT. PATH OF EGRESS 2 X 5W MR16 LED
6
INTRODUCTION
LUXRAY MC LED SERIES
EF40 & EF40P
SERIES
RETRACT-A-LITE
SERIES
MINI RETARCT-ALITE SERIES
LITERAY SERIES
EF9 / EF9Q / EF9M
SERIES
EF15 SERIES
P. 136-137
P. 138
P. 139
P. 140
P. 141
P. 142
P. 143
P. 144
EF18 / EF18D / EF18T
SERIES
DISTINCTION MC SERIES
DISTINCTION MC EFR
SERIES
SURVIVE-ALL MC
EF39 & EF39P
SERIES
EF25 SERIES
EF26 / EF26DS /
EF26D SERIES
EF11 SERIES
EF30 SERIES
P. 145
P. 146
P. 147
P. 148-149
P. 150
P. 151
P. 152
P. 153
Project/Location:
Lamp Chart
MR16 LED EMERGENCY LIGHTING
Contractor:
Date:
Prepared by:
LAMP TYPE
CODE
VOLTAGE
LUMEN
24V - 18W
MR16 LED ILLUMINATION
PROVIDER®
A
570.0040-E
570.0037-E
570.0031-E
S8, High intensity
tungsten lamps 570.0061-E
double contact
570.0120-E
bayonet base
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
188
126
400
188
12V - 18W
276
24V - 9W
75
580.0012-E
580.0017-E
580.0013-E
580.0011-E
T-2 1/4, Bi-pin
halogen lamps
580.0022-E
6V - 6W
113
6V - 10W
200
6V - 8W
163
6V - 12W
240
6V - 20W
400
12V - 8W
163
12V - 12W
276
580.0014-E
580.0015-E
580.0023-E
24V - 20W
133
580.0016-E
12V - 14W
300
580.0027-E
12V - 20W
314
H3, Incandescent lamp 580.0030-E
wedge base
12V - 55W
748
24V - 70W
791
6V - 7.2W
T-2 3/4,
Bi-pin
halogen
lamps
580.0031-E
570.0026-E
X
B
X
X
X
X
23’
14’
23’
16’
24’
17’
X
X
A
B
x
x
A
EF11
X
X
94
138
6V - 25W
12V - 13W
A
EF15
B
X
400
12V - 9W
570.0038-E
B
EF26 / DS / D
A
10’
400
6V - 13W
570.0011-E
EF18 / D / T
300
24V - 25W
12V - 9W
570.0020-E
EF9 / Q / M
250
6V - 18W
12V - 25W
120V - 15W
570.0025-E
RP-11, High
570.0022-E
intensity tungsten
lamps
570.0030-E
double contact
bayonet base
570.0058-E
X
10’
X
X
B
B
X
X
-
10’
-
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
5’
X
EF30
A
X
X
16’
X
X
X
X
X
X
X
14’
17’
14’
17’
14’
17’
14’
15’
12’
15’
12’
15’
12’
15’
12’
23’
17’
23’
17’
23’
17’
16’
13’
16’
13’
16’
13’
16’
13’
20’
15’
20’
15’
20’
15’
20’
15’
21’
15’
21’
15’
21’
15’
21’
15’
X
X
X
X
34’
26’
34’
26’
34’
26’
X
X
34’
26’
78’
104’
74’
X
X
X
X
X
X
X
X
X
X
150
X
X
12’
5’
12’
-
12’
-
12’
-
12’
-
12V - 9W
138
X
X
14’
8’
18’
13’
18’
13’
18’
13’
18’
13’
570.0028-E
12V - 12W
150
x
x
X
X
X
X
570.0029-E
12V - 18W
264
24’
14’
18’
12’
18’
12’
18’
12’
18’
12’
24V - 9W
113
X
X
12’
2’
15
9’
15’
9’
15’
9’
15’
9’
24V - 18W
240
21’
10’
21’
15’
21’
15’
21’
15’
21’
15’
6V - 5.4W
68
X
X
X
X
X
X
X
X
570.0012-E
X
A= Typical spacing 7’ mounting 6’ wide
B= Typical spacing 15’ mounting 6’ wide
EFXPR
B
A
B
MR16 LED LAMP BENEFITS
With the remarkable technology development in the last
decade, the light-emitting diode (LED) is becoming the
preferred solution in low- and medium-power lighting
applications. The emergency lighting industry is no
exception: today virtually every new product introduced to
market includes “white” LEDs for emergency illumination.
• CSA C22.2 No. 141 certified.
• Energy-efficient LED MR16 lamp provides equivalent
lighting performance to a much higher watt halogen
MR16 lamp.
• Reduces required battery capacity by 75%, providing
necessary illumination with fewer remote heads and
battery units for project cost savings.
Extremely efficient and long-lasting, LED lamps become the
natural alternative to incandescent lamps due to three main
advantages:
• Small profile, compact white lighting is ideal for
architectural applications.
• = lamp efficacy: 50 - 70 lumen per watt compared to 15 30 lumen per watt of the best halogen lamp.
• Vibration-resistant LED stands up to industrial
environments.
• = operational life: 30,000+ hours, equivalent to a lifetime
warranty in emergency lighting.
• Ideal for indoor and outdoor use.
• = lower lamp temperature (80 - 120°C) is a huge benefit
for lighting in hazardous locations.
X
X
17’
108’
100
6V - 9W
570.0025-E
T-5, Incandescent 570.0045-E
lamp wedge base
570.0046-E
570.0016-E
A
340-LUMEN 5W MR16 LED
200-LUMEN 4W MR16 LED
104’
74’
108’
74’
X
X
X
X
X
X
X
X
X
X
X
Keeping pace with technology, in 2012 we introduced a
12V-5W MR16 LED lamp. With a typical luminous flux of 340
lumens, this lamp has the same lighting performance as
a 20W high-output halogen MR16. A twin emergency head
installed at a height of 7.5ft illuminates more than a 70ft
path of egress.
Leading the technology trend, Emergi-Lite® offers a
complete series of 4W MR16 LED lamps available for all
the standard battery voltages: 6V, 12V, 24V and 120V. With
up to 30,000 hours of operational life and a luminous
flux of typically 200 lumens, they are available with most
emergency heads designed to hold an MR16 lamp and meet
the majority of illumination specifications. For example: one
pair of LED emergency heads installed at a height of 7.5ft,
illuminates a 6ft by 40ft path of egress.
510-LUMEN 6W MR16 LED
New in Fall 2013, we intoduce a 12V - 6W MR16 LED lamp,
which offer typical luminous flux of 510 lumens. Like the
lower wattage MR16 LED lamps, this new lamp is specially
designed for emergency lighting. It offers the same lighting
preformance as the 35W or 20W Mr16 IR. A twin emergency
head installed at a height of 7.5’ illuminates approximately
100’ path of egress.
Compared to halogen lamps (16-20W), these 4W MR16
LED lamps illuminate the same area of egress during an
emergency situation by using 75% less power. This has
a direct impact on the battery size, reducing the back-up
capacity needs by 75%. Consequently, it also reduces the
total cost of the application, with the use of smaller battery
capacity units, the possibility of using fewer fixtures due to
superior illumination, thus also reducing electrical wiring,
and it it reduces the environmental footprint.
Typical spacing is based on a 6” wide path and 80.50.20 reflectances.
40-FT. PATH OF EGRESS 2 X 4W MR16 LED
70-FT. PATH OF EGRESS 2 X 5W MR16 LED
154
6
EF41 SERIES
EFXPR SERIES
LAMP CHARTS
GLOSSARY
P. 154
P. 155
P. 156-158
P. 159
135
Project/Location:
Contractor:
REMOTE HEADS OVERVIEW
EMERGENCY LIGHTING HEADS:
PERFORMANCE & TECHNOLOGY
Date:
Prepared by:
PAR36 SEALED BEAM LAMPS
Emergency head performance also depends on lamp optics:
the reflector and the lens. This is especially critical in damp
areas where vapors and water condensation can deteriorate
the electrical contacts and the reflector performance.Sealed
beam lamps are recommended for such applications.
Emergency Lighting Heads represent a key
element of an emergency lighting system
performance. During a power failure, these
lamp heads must provide adequate lighting
levels for safe evacuation.
Sealed beam lamp construction includes a metal coated
glass reflector and a lens, designed to provide a light beam
of a certain opening: narrow, medium, large, etc. The most
common lamps used are those with a 4.5’’ diameter (PAR36),
available in both incandescent and halogen versions. As to
miniature lamps, there are sealed beam lamps dedicated to
long life applications (4,000 hours, 7-8 lumens/Watt) and for
emergency lighting (50 to 300 hours, 12-20 lumens/Watt).
What level of illumination is necessary to ensure safe
evacuation? Minimum levels are established by the National
Building Code of Canada:
“3.2.7.3. Emergency Lighting
Originally, lamp life wasn’t an issue. However, this has become
increasingly important in recent years, with the introduction of
sophisticated emergency lighting fixtures with periodic
self-test and self-diagnostic features. Such a system includes
a micro-controller board that automatically simulates a
power failure and forces the fixture in emergency lighting
mode every 30 days for at least 30 seconds and tests both the
batteries and the lamps. Even if the duration of the self-test is
minimal compared to the lamp life, the repetitive connection
and disconnection cycle of the lamps increases the risk of a
premature failure caused by the initial high current applied.
1 - Emergency lighting shall be provided to an average level
of illumination not less than 10 lx at floor or tread level
2 - Emergency lighting to provide an average level of
illumination of not less than 10 lx at floor or catwalk level
shall be included in a service space referred to in
Sentence 3.2.1.1.7).
3 - The minimum value of the illumination required by Sentences (1)
and (2) shall not be less than 1 lx.”
You have probably already noticed the short lamp life of these light
sources. Who would be interested in using a bulb that only lasts 50
hours? The answer is simple: such a lamp produces 25% to 30%
more light than a lamp of the same wattage but longer lamp life
(i.e. 1,000 hours). By design, the filament in an emergency lighting
head is used at higher temperatures, increasing light output.
MR16 GENERATION
Fortunately, the lamp life issue was resolved with a new
generation of lamps that use MR16 technology (MR16 stands
for Multi-facetted Reflector, 16/8’’ diameter). Increasingly
popular, the MR16 contains everything in one: miniature
halogen lamp, metal coated glass reflector and, for the most
part, a glass lens cemented to the reflector. Easy to install,
MR16 lamps are popular in both residential and commercial
applications, and increasingly specified for emergency lighting.
During a power failure, the emergency power supply is provided
to the heads from batteries. Equipment manufacturers and
customers should use high intensity light sources, with efficient
light levels and distributions.
In addition to their bright directional beam, these lamps offer
good efficacy (11 to 18 lumens/Watt), as well as long life (2,000
to 6,000 hrs). First, the use of a glass lens which is clear
and thin, allows the MR16 to absorb much less light than a
standard diffuser lens; and second, efficient light distribution is
accomplished by the multi-facetted reflector.
MINIATURE LAMPS:
TUNGSTEN AND QUARTZ HALOGEN
Most commonly used emergency lighting heads are fabricated of
an injection-molded thermoplastic housing containing a miniature
lamp, a metallic reflector and a polycarbonate lens. Lamps use a
tungsten filament enclosed in a filling gas mixture of argon and
nitrogen and are generally referred to as incandescent lamps.
200-LUMEN 4W MR16 LED
Leading the technology trend, Emergi-Lite® offers a complete
series of 4W MR16 LED lamps available for all the standard
battery voltages: 6V, 12V, 24V and 120V. With up to 30,000 hours
of operational life and a luminous flux of typically 200 lumens,
they are available with most emergency heads designed to
hold an MR16 lamp and meet the majority of illumination
specifications. For example: one pair of LED emergency heads
installed at a height of 7.5ft, illuminates a 6ft by 40ft path
of egress.Compared to halogen lamps (16-20W), these 4W
MR16 LED lamps illuminate the same area of egress during
an emergency situation by using 75% less power. This has a
direct impact on the battery size, reducing the back-up capacity
needs by 75%. Consequently, it also reduces the total cost
of the application, with the use of smaller battery capacity
units, the possibility of using fewer fixtures due to superior
illumination, thus also reducing electrical wiring, and it it
reduces the environmental footprint.
Better performance is obtained with quartz halogen lamps, which
are still incandescent lamps, but the filling gas (iodide/chloride)
allows the tungsten filament to operate at higher temperatures.
This results in higher luminous intensity, 20 to 30% superior to
standard incandescent lamps of the same wattage and lamp life.
However, using high temperatures also increases vaporization of
the filament which shortens its life. As power failures are relatively
scarce (let’s say 4 to 6 per year) and duration of emergency lighting
between 30 minutes to 2 hours, lamp heads are only used between
3 to 12 hours per year. A lamp with an average life of 50 hours
should therefore be functional for over four years.
Lamp manufacturers offer two types of miniature lamps: long life
and high light output.
136
Project/Location:
Contractor:
Date:
Prepared by:
340-LUMEN 5W MR16 LED
510-LUMEN 6W MR16 LED
Keeping pace with technology, in 2012 we introduced a 12V-5W
MR16 LED lamp. With a typical luminous flux of 340 lumens, this
lamp has the same lighting performance as a 20W high-output
halogen MR16. A twin emergency head installed at a height of 7.5ft
illuminates more than a 70ft path of egress.
New in Fall 2013, we intoduce a 12V - 6W MR16 LED lamp,
which offer typical luminous flux of 510 lumens. Like the lower
wattage MR16 LED lamps, this new lamp is specially designed for
emergency lighting. It offers the same lighting preformance as the
35W or 20W Mr16 IR. A twin emergency head installed at a height of
7.5’ illuminates approximately 100’ path of egress.
STANDARD WEDGE-BASE 9W
INCANDESCENT LAMP
Standard Emergency Lighting Units
with 9W wedge-base incandescent lamps
4W MR16 LED LAMPS
Same Standard Emergency Lighting Units with
4W MR16 LED Lamps
LAMP
SUFFIX
VOLTAGE
WATTAGE
LUMENS REPLACEMENT #
LA
6
4
130
580.0097-E
LG
12
4
170
580.0093-E
LL
24
4
200
580.0098-E
5W MR16 LED LAMP
LAMP
SUFFIX
VOLTAGE
WATTAGE
LI
12
5
LUMENS REPLACEMENT #
340
580.0104-E
NEW! 6W MR16 LED LAMPS
137
LAMP
SUFFIX
VOLTAGE
WATTAGE
LJ
12
6
LUMENS REPLACEMENT #
510
580.0106-E
Remote Fixture
Lux-Ray™ LED
Series
Project/Location:
Contractor:
Date:
Prepared by:
Rugged, Versatile, Sophisticated
FEATURES
•
•
•
•
•
•
TABLE A: SPACING FOR AVERAGE 1FC
our-LED light engine with redundant connections
F
Powder-coated Die-Cast aluminum construction
Clear Polycarbonate lens allows for maximum lumen output
Surface Wall Mount
Certified to the CSA 22.2 No.141 standard
NEMA-3R Damp and Wet locations
MODEL TYPE
• Operating temperature -40°C to + 50°C
OPTIONS
•
•
•
•
•
AC, ACDC, DC
9’
6’ X 50’
With option -H
11’
6’ X 60’
6’ X 50’
With option -FT
12’
6’ X 40’
6’ X 60’
3’ X 70’
-
With option -FTH
15’
6’ X 50’
-
Note: The illumination level meets ALL the requirements of the
National Building Code-Canada and the Life Safety Code
(NFPA 101):
1) Average of 1 foot-candle (10.7 lux) or more
2) Minimum at any point of 0.1 foot-candle (1.07 lux) or more
3) Maximum-to-minimum illumination uniformity ratio of 40:
1 or less
NEMA-3R
WIDE BEAM (STANDARD)
AC SPECS: 120/347VAC
NORMAL
LIGHTING
MODEL TYPE
Standard
Indoor reflectance: 80/50/20 and 10-ft wide corridor.
Outdoor reflectance: 0/30/10
orward-throw light distribution
F
Dual-mode: normal and emergency LED lighting
High-lumen output
Photo-switch: dusk-to-dawn control of normal lighting
Infrared remote control (normal lighting)
POWER CONSUMPTION
WATTAGE CAPACITY
MOUTING
HEIGHT SINGLE CENTRE-TO-CENTRE
EMERGENCY
LIGHTING
6-12VDC
REMOTE
CURRENT
(MAX)
POWER
(MAX)
CURRENT
(MAX)
POWER
(MAX)
POWER
(MAX)
0.12/0.05 A
12W
0.12/0.05 A
12W
8W
1fc
AC, ACDC, DC -H
0.18/0.07 A
18W
0.18/0.07 A
18W
14W
2AC (120VAC only)
0.12 A
12W
0.12 A
12W
-
2AC-H (120VAC only)
0.18 A
18W
0.18 A
18W
-
1fc average
min
imu
m
9’
50’ 28’
6’
*Note: Only unswitched AC input; normal lighting with photo-switch or remote control
DIMENSIONS
FORWARD THROW (OPTIONAL)
Dimensions are approximate and subject to change.
3” [7.5 cm]
65/8” [16.8 cm]
12’
91/2” [24 cm]
3” [7.5 cm]
m
imu
min
1fc
age
aver
1fc
Window for
photo-switch
(optional)
22’
40’
6’
ORDERING INFORMATION
FUNCTION: REMOTE FIXTURES
(-40… +50°C)
SERIES
LUX= Lux-Ray LED
™
AC= AC-only
ACDC= AC/6-12VDC remote
DC= 6-12VDC remote fixture
2AC= AC-only two circuits: 120/120 or 277/277V
COLOUR
OW= off-white
BK= black
DB= dark bronze
PG= platinum grey
OPTION
-FT= Forward throw lighting
-H= High lumen output (max. 30°C)
-P= Photo-switch, normal lighting (models AC, ACDC only)
-RC= Remote control - infrared (models AC, ACDC only)*
-2= 277VAC 60Hz input
* Remote control keypad (TB-RC1-E) ordered separately
EXAMPLE: LUXACDCBK-H-P
138
Project/Location:
EF40 & EF40P
Series
Contractor:
Date:
Prepared by:
Remote Fixture
FEATURES
TYPICAL SPECIFICATIONS
• Quality illumination requires fewer fixtures
Supply and install Emergi-Lite® EF40P Series remote emergency
lighting. These remote fixtures will consist of either single or
double lamp configurations as specified and include a UV resistant
fire retardant polycarbonate back plate and a clear heavy-duty UV
resistant polycarbonate light cover.
The remote fixture shall be certified to CSA C22.2 No. 141.
The head(s) shall be fully adjustable and be equipped with high
efficiency MR16 halogen or LED lamp(s) of _____ V, _____ W.
The remote unit shall be Emergi-Lite® model:
.
• Clear polycarbonate UV and impact resistant lens with
optional tamper-proof screws to prevent tampering.
• Easy lamp replacement
• CSA certified to C22.2 No. 141
• Modern design will blend into surroundings
• Selection of Die-Cast or polycarbonate back plate
• For indoor use only
WIRE GUARDS
DIMENSIONS
460.0029-E
Dimensions are approximate and subject to change.
73/8” [18.7 cm]
Wall Mount
REPLACEMENT LAMPS: MR16 EF40P
47/8” [12.3 cm]
33/4” [9.5 cm]
ORDERING
CODE
LAMP TYPE
580.0074-E
MR16 flood
6V-6W
580.0079-E
MR16 flood
6V-10W
580.0080-E
MR16 flood
12V-12W
VOLTAGE
580.0070-E
MR16 flood
24V-12W
580.0097-E
MR16 LED
6V-4W
580.0093-E
MR16 LED
12V-4W
580.0104-E
MR16 LED
12V-5W
580.0106-E
MR16 LED
12V-6W
580.0098-E
MR16 LED
24V-4W
For the complete list, please see the lamp chart on pages 156 to 158
REPLACEMENT LAMPS: MR16 EF40
ORDERING CODE
LAMP TYPE
VOLTAGE
580.0068-E
MR16 infrared
12V-20W
580.0077-E
MR16 flood
24V-20W
ORDERING INFORMATION: EF40P
SERIES
EF40P= polycarbonate
NUMBER OF LAMPS
LAMP TYPE
Blank= one lamp
D= two lamps
M= MR16
COLOUR
Blank= factory white
B= black
G= grey
LAMP TYPE/VOLTAGE/WATTAGE
6V6W= MR16, 6V-6W
6V10W= MR16, 6V-10W
12V12W= MR16, 12V-12W
24V12W= MR16, 24V -12W
LA= MR16 LED 6V-4W
LG= MR16 LED 12V-4W
LI= MR16 LED 12V-5W
LJ= MR16 LED 12V-6W
LL= MR16 LED 24V-4W
OPTIONS
Blank= no option
T= tamper-proof screws*
*Tamper-proof bit for dry
location Part No. 690.0454-E
(one bit needed per order )
ORDERING INFORMATION: EF40
SERIES
EF40 = Die-Cast
backplate
NUMBER OF LAMPS
Blank= one lamp
D= two lamps
LAMP TYPE
M= MR16
COLOUR
Blank= f actory
white
B= black
G= grey
EXAMPLE: EF40PDM-B-6V6WT
139
LAMP TYPE/VOLTAGE/WATTAGE
12V20W = MR16IR, 12V-20W
24V20W = MR16, 24V-20W
OPTIONS
Blank= no option
T= tamper-proof screws*
*Tamper-proof bit for dry location
Part No. 690.0454-E (one bit
needed per order )
Project/Location:
Retract-a-Lite™
Series
Contractor:
Date:
Prepared by:
Remote Fixture
FEATURES
TYPICAL SPECIFICATIONS
• Remote only visible upon power failure
Supply and install Emergi-Lite® Retract-a-Lite™ Series of remote
fixture: The unit shall be designed to be concealed in walls or ceilings
with a cavity. The unit equipment shall be completely concealed in the
wall or ceiling in the absence of remote power. Upon DC power supply
the unit will rotate its door by 180° to expose the emergency lamps,
and power them. After the DC power disconnect the lamps will turn
off and the unit will conceal the heads by rotating the door by 180°.
The DC-remote unit shall not require the presence of AC power in
order to open or close the door.
Under normal conditions, the only visible parts of the unit shall be
the off-white flat door and trim plate that can be customized on site
with paint or other suitable wall covering. The light source shall be
MR16 halogen lamps of specified wattage and light output.
The remote unit shall be the Emergi-Lite® model:
.
• Front can be painted or wallpapered on-site to match existing
decor
• Fully automatic operation: The unit door opens upon supply with
DC voltage from battery and closes after voltage disconnect.Time
delay option required on battery unit to properly close the door
• AC line voltage not required
• Emergency lights: Two high efficacy MR16 halogen or MR16 LED
lamps
• Certification: CSA C22.2 No.141
DIMENSIONS
REPLACEMENT LAMPS: MR16
Dimensions are approximate and subject to change.
91/8” [23.1 cm]
DC VOLTAGE
JUNCTION
BOX
71/4” [18.3 cm]
71/4” [18.3 cm]
33/4” [9.6 cm]
WIRE GUARDS
460.0082-E
Wall Mount
12RTLR= 12VDC remote
24RTLR= 24VDC remote
LAMP TYPE
VOLTAGE/WATTAGE
MR16 12W Flood
12V-12W
12V-20W
580.0064-E
MR16 20W Flood
580.0083-E
MR16 35W Flood
12V-35W
580.0076-E
MR16 50W Flood
12V-50W
580.0068-E
MR16 IR 20W Flood
12V-20W High-output
580.0090-E
MR16 IR 35W Flood
12V-35W High-output
580.0089-E
MR16 IR 50W Flood
12V-50W High-output
580.0084-E
MR16
24V-35W
580.0070-E
MR16
24V-12W
580.0077-E
MR16
24V-20W
580.0078-E
MR16
24V-50W
580.0093-E
MR16 LED
12V-4W
580.0098-E
MR16 LED
24V-4W
580.0104-E
MR16 LED
12V-5W
580.0106-E
MR16 LED
12V-6W
For the complete list, please see the lamp chart on pages 156 to 158
ORDERING INFORMATION
SERIES
MODEL
580.0080-E
WATTAGE FOR EACH OF THE 2 LAMPS
-12= MR16, 12W
-20= MR16, 20W
-35= MR16, 35W
-50= MR16, 50W
-20H= MR16, High lumen output, 20W
-35H= MR16, High lumen output, 35W
-50H= MR16, High lumen output, 50W
-LG= MR16 LED, 12V-4W
-LI= MR16 LED, 12V-5W
-LL= MR16 LED, 24V-4W
-LJ= MR16 LED, 12V-6W
Note: The remote fixture is compatible with all
Retract-a-Lite™ battery units
EXAMPLE: 12RTLR-20TB
140
OPTIONS
TB= T-Bar mounting kit
Mini
Retract-a-Lite™
Series
Project/Location:
Contractor:
Date:
Prepared by:
For AC Power Generator
FEATURES
TYPICAL SPECIFICATIONS
Supply and install Emergi-Lite® Series Mini Retract-a-Lite™. The
unit shall be designed to be completely concealed in walls with a
cavity. The equipment shall consist of a metal housing containing two
modules joined by a flexible bracket and electric conduit. One module
contains the power transformer and electrical connection box; the
other module contains the emergency lights installed on the back of
a door able to rotate several turns of 360°. The unit equipment shall
be completely concealed in the wall, after the installation through a
rectangular opening not larger than 8.25” by 5.75”.
•Easy to retrofit in finished walls: the unit slides in through an
8.25” by 5.75” hole
• No back-box needed to pre-install
• Output: 12VDC with up to 100W of power
• Direct connection to 120 or 347VAC power generators
• Emergency lights: MR16 halogen and MR16 LED lamps
• Certification: CSA C22.2 No. 141
In stand-by mode, the only visible parts of the unit shall be the
off-white flat door and trim plate that can be customized on site with
paint or other suitable wall covering. Upon AC power supply the unit
will expose the emergency heads by rotating its door 180° and then
will power the lamps. At the end of the AC power, the lamps will turn
off and the unit will retract the heads by rotating the door 180° in the
same direction.
The unit shall not require the presence of AC power in order to close
the door and conceal the lights. The door of the unit shall be easy
to force-turn (open or close) by hand. The light source shall be 12V
MR16 halogen lamps of specified wattage and light output.
The remote unit shall be the Emergi-Lite® model:
DIMENSIONS
Dimensions are approximate and subject to change.
7” [17.8 cm]
COMPLETE UNIT
51/4” [13.2cm]
91/8” [23.2cm]
REPLACEMENT LAMPS
73/4” [19.7cm]
31/2” [8.9 cm]
175/8” [44.9 cm]
INSTALLED UNIT
MODEL
TYPE
VOLTAGE/WATTAGE
580.0080-E
MR16 flood
12V-12W
580.0064-E
MR16 flood
12V-20W
580.0083-E
MR16 flood
12V-35W
580.0076-E
MR16 flood
12V-50W
580.0068-E
MR16 IR flood
12V-20W High output
580.0090-E
MR16 IR flood
12V-35W High output
580.0089-E
MR16 IR flood
12V-50W High output
580.0093-E
MR16 LED
12V-4W
580.0104-E
MR16 LED
12V-5W
580.0106-E
MR16 LED
12V-6W
For the complete list, please see the lamp chart on pages 156 to 158
ORDERING INFORMATION
SERIES
MR
UNIT CAPACITY
G= remote AC generator,
maximum 100W
AC VOLTAGE
Blank= 120VAC
2= 277VAC
3= 347VAC
LAMP WATTAGE (12V MR16)
/12= MR16, 12W
/20= MR16, 20W
/35= MR16, 35W
/50= MR16, 50W
/20H= MR16, High lumen output, 20W
/35H= MR16, High lumen output, 35W
/50H= MR16, High lumen output, 50W
/LG= MR16 LED, 12V-4W
/LI= MR16 LED, 12V-5W
/LJ= MR16 LED, 12V-6W
Note: Testing requires minimum 5 seconds of power supply.
EXAMPLE: MRL80/20HUN
141
Project/Location:
Literay Series
Contractor:
Date:
Wall Mounted
Remote Head
FEATURES
Prepared by:
TYPICAL SPECIFICATIONS
• Outdoor/Indoor installation
Wall mount unit shall be gasketed Die-Cast aluminum housing,
impact resistant polycarbonate diffuser. The lamps shall be
adjustable for aisle or area distribution.
Fixture shall be supplied with gasket and shall be suitable for
installation on any four inch octagonal box.
The remote unit shall be Emergi-Lite® model:
• Compact wall sconce unit for indoor and outdoor use
• High impact resistant polycarbonate diffuser
• Adjustabe lamps
• Die-Cast aluminum housing
• Vandal resistant option
.
REPLACEMENT LAMPS
• CSA Certified to C22.2 No. 141
WIRE GUARDS
460.0082-E
Wall Mount
DIMENSIONS
MODEL
LAMP TYPE
VOLTAGE/WATTAGE
580.0079-E
MR16 Flood
6V-10W
580.0080-E
MR16 Flood
12V-12W
580.0068-E
MR16 Flood
24V-20W
580.0077-E
MR16 Flood
24V-20W
580.0070-E
MR16 Flood
24V-12W
580.0097-E
MR16 LED
6V-4W
580.0093-E
MR16 LED
12V-4W
580.0104-E
MR16 LED
12V-5W
580.0098-E
MR16 LED
24V-4W
580.0106-E
MR16 LED
12V-6W
For the complete list, please see the lamp chart on pages 156 to 158
Dimensions are approximate and subject to change.
5” [12.7 cm]
8” [20.4 cm]
7” [17.9 cm]
ORDERING INFORMATION
SERIES
EF33= exterior remote
LAMP TYPE
Blank=(1) med. base socket
only (max. 60W) no lamp
included
M= MR16
COLOUR
Blank= factory white
B= black
DG= dark grey
BZ= dark bronze
EXAMPLE: EF33M-12V12W
142
VOLTAGE/ WATTAGE
Blank= no lamps
-6V10W= MR16, (2) 6V-10W
-12V12W= MR16, (2) 12V-12W
-12V20W= MR16, (2) 12V-20W
-24V12W= MR16, (2) 24V-12W
-24V20W= MR16, (2) 24V-20W
-12V20WH= MR16, (2) 12V-20W
high-output
-LA= MR16 LED, 6V-4W
-LG= MR16 LED,12V-4W
-LL= MR16 LED,24V-4W
-LI= MR16 LED,12V-5W
-LJ= MR16 LED,12V-6W
OPTIONS
-VR= vandal resistant screws
990.0119-E= t amper-proof
bit*
C= clear lens
*One bit needed per order.
EF9/EF9Q/EF9M
Series
Project/Location:
Contractor:
Micro Tungsten Lamps,
Micro-Quartz Lamps,
MR16 Lamps, or LED
Date:
Prepared by:
FEATURES
TYPICAL SPECIFICATIONS
• Available with tungsten, micro-quartz MR16 or LED lamps
Lamp head and stem shall be injection molded, impact resistant,
flame retardant thermoplastic and shall require no tool for aiming
or adjustment. The lens shall be inverse concave design and fully
adjustable for aisle or area distribution during installation without
the need to energize the lamp. Visual identification of distribution
shall be provided through position of adjustment pins.
Fixture shall be supplied with a canopy for installation on any four
inch octagon box. Housing shall be designed to allow for lamp
replacement if required.
The remote unit shall be the Emergi-Lite® model:
.
• Fire-retardant thermoplastic
o
• 300 rotation
• CSA certified to C22.2 No. 141
• 6, 12 and 24V with various wattages
DIMENSIONS
Dimensions are approximate and subject to change.
WIRE GUARDS
33/16”
[8.2cm]
215/16” [7.4cm]
460.0029-E
Wall ceiling Mount
REPLACEMENT LAMPS
59/16”
[14.2cm]
5” [12.7cm]
3 ”
[8.1cm]
3/16
85/16”
[21.1cm]
413/16”
[12.3cm]
MODEL
AC SPECS
DC SPECS
570.0016-E
Tungsten
6V-9W
570.0045-E
Tungsten
24V-9W
570.0015-E
Halogen (quartz)
12V-12W
570.0097-E
MR16 LED
6V-4W
570.0093-E
MR16 LED
12V-4W
570.0104-E
MR16 LED
24V-4W
570.0098-E
MR16 LED
12V-5W
570.0106-E
MR16 LED
12V-6W
For the complete list, please see the lamp chart on pages 156 to 158
5” [12.7cm]
ORDERING INFORMATION
SERIES
EF9= m
ini,
PAR 18
NUMBER OF LAMPS
Blank= single head
D= double head
T= triple head
LAMP TYPE
Blank= tungsten,
wedge base
Q= halogen, quartz
bi-pin
M= halogen, MR16 LED
COLOUR
Blank= factory white
-B= black
EXAMPLE: EF9Q6V8W
143
VOLTAGE/WATTAGE
-6V9W= 6V-9W, wedge base
-12V9W= 12V-9W, wedge base
-12V18W= 12V-18W, wedge base
-24V9W= 24V-9W, wedge base
-24V18W= 24V-18W, wedge base
-6V8W= 6V-8W, quartz bi-pin
-6V12W= 6V-12W, quartz bi-pin
-12V8W= 12V-8W, quartz bi-pin
-12V12W= 12V-12W, quartz bi-pin
-6V6W= MR16, 6V-6W
-6V10W= MR16, 6V-10W
-12V12W= MR16, 12V-12W
-12V20W= MR16, 12V-20W
-24V12W= MR16, 24V-12W
-24V20W= MR16, 24V-20W
-LI= MR16 LED, 12V-5W
-LG= MR16 LED, 12V-4W
-LA= MR16 LED, 6V-4W
-LL= MR16 LED, 24V-4W
-LJ= MR16 LED, 12V-6W
Recess Mounted
EF15 Series
Project/Location:
Contractor:
Date:
Compact Emergency Lighting
FEATURES
Prepared by:
WIRE GUARDS
• Durable themoplastic trim (metal trim as an option)
460.0033-E
• PAR 36 Gimbal ring adjustable on two planes to 45°
Wall or ceiling mount
REPLACEMENT LAMPS
• Complete unit, no additional housing needed
• Certified CSA C22.2 No.141
DIMENSIONS
MODEL
LAMP TYPE
570.0026-E
Tungsten
VOLTAGE/WATTAGE
6V-9W
570.0025-E
Tungsten
12V-9W
570.0045-E
Tungsten
24V-9W
For the complete list, please see the lamp chart on pages 156 to 158
Dimensions are approximate and subject to change.
1/4
[15.87 cm]
cm]
661/2
”” [15.87
ceiling opening
opening
ceiling
9” [22.86 cm]
51/2”
[13.97 cm]
4 ”
[11.43 cm]
1/2
Wire Box
Back Box
Plaster
51/4”
Frame [13.33 cm]
Trim
Gimbal Ring
ORDERING INFORMATION
SERIES
LAMP TYPE
HOUSING
COLOUR
EF15= PAR 36 recessed
with plastic trim
Blank= tungsten
H= quartz sealed
beam
Q= halogen
S= sealed beam
Blank= plastic trim
M= metal trim
Blank= factory white
BK= black
VOLTAGE/ WATTAGE/ LAMP TYPE
-6V9W= tungsten, 6V - 9W, wedge base
-6V__W= tungsten, 6V - 18 or 25W, D.C.B.
-12V__W= tungsten, 12V - 9 or 18W, wedge base
-12V25W= tungsten, 12V - 25W, D.C.B.
-24V__W= tungsten, 24V - 9 or 18W, wedge base
-24V25W= tungsten, 24V - 25W, D.C.B.
-6V__W= halogen, 6V - 8, 12 or 20W, quartz bi-pin
-12V__W= halogen, 12V - 8, 12, 20 or 55W, quartz bi-pin
-24V__W= halogen, 24V - 20 or 70W, quartz bi-pin
-6V__W= tungsten, 6V - 9, 12, 18 or 25W, sealed beam
-12V__W= tungsten, 12V - 12, 18 or 25W, sealed beam
-6V__W= halogen, 6V - 8, 12 or 20W, quartz sealed beam
-12V__W= halogen, 12V - 8, 12 or 37W, quartz sealed beam
-32V__W= tungsten, 32V - 18 or 25W, D.C.B.
-120V__W= 120V - 10 or 15W, D.C.B.
-120V__W= quartz, 120V - 35 or 50W, D.C.B.
*Available with metal trim only.
NOTE : “___” insert wattage required
EXAMPLE: EF15Q-12V12W
144
EF18/EF18D/
EF18T Series
Project/Location:
Contractor:
Date:
Surface Mounted,
Remote Fixture
Prepared by:
FEATURES
TYPICAL SPECIFICATIONS
• PAR 36, surface-mounted, large remote fixtures
Base and remote head are injection-molded thermoplastic,
shockproof and flame retardant. Shall be supplied factory white or
black. The setting point shall provide visual indication of the light
distribution.
The fixture shall be supplied with a canopy to be installed on any
standard octagonal box. The housing shall be designed to allow lamp
replacement when required.
The remote unit shall be the Emergi-Lite® model:
• Single, double or triple head
• Positive aim swivel
• CSA certified to C22.2 No. 141
REPLACEMENT LAMPS
MODEL
LAMP TYPE
VOLTAGE/WATTAGE
570.0016-E
Mini tungsten, wedge
base
6V-9W
570.0025-E
Mini tungsten, wedge
base
12V-9W
580.0023-E
Mini halogen (quartz),
bi-pin
WIRE GUARDS
24V-20W
For the complete list, please see the lamp chart on pages 156 to 158
470.0035-E
Wall Mount (EF18)
470.0082-E
Wall Mount (EF18D)
470.0078-E
Wall Mount (EF18T)
DIMENSIONS
Dimensions are approximate and subject to change.
63/8” [17.27 cm]
107/8” [27.68 cm]
EF18
43/4” [12.06cm]
123/8” [31.24 cm]
5” [12.7 cm]
35/4” [13 cm]
EF18T
71/4” [18.41 cm]
63/8” [16.2cm]
EF18D
91/2” [24.13 cm]
ORDERING INFORMATION
SERIES
LAMP TYPE
COLOUR
VOLTAGE/WATTAGE/LAMP TYPE
EF18= single
EF18D= double
EF18T= triple
Blank= tungsten
Q= halogen
S= sealed beam
H= quartz sealed beam
Blank= factory white
B= black
C= chrome
M= factory white (metal)
-6V9W= tungsten, 6V - 9W, wedge base
-6V__W= tungsten, 6V - 18 or 25W, D.C.B.
-12V__W= tungsten, 12V - 9 or 18W, wedge base
-12V25W= tungsten, 12V - 25W, D.C.B.
-24V__W= tungsten, 24V - 9 or 18W, wedge base
-24V25W= tungsten, 24V - 25W, D.C.B.
-6V__W= halogen, 6V - 8, 12 or 20W, quartz bi-pin
-12V__W= halogen, 12V - 8, 12, 20 or 55W, quartz bi-pin
-24V__W= halogen, 24V - 20 or 70W, quartz bi-pin
-6V__W= tungsten, 6V - 8, 12, 18 or 25W, sealed beam
-12V__W= tungsten, 12V - 12, 18 or 25W, sealed beam
-6V__W= halogen, 6V - 8, 12 or 20W, quartz sealed beam
-12V__W= halogen, 12V - 8, 12 or 37W, quartz sealed beam
-32V__W= tungsten, 32V - 18 or 25W, D.C.B.
-120V_W= tungsten, 120V-10 or 15W, D.C.B.
-120V35W= halogen, 120V - 35W, D.C.B.
-120V50W= quartz, 120V - 50W, D.C.B*
*Only available in metal heads
EXAMPLE: EF18Q-12V12W
145
OPTION
FP= teflon coated lens
Project/Location:
Distinction Series
™
Surface Designer Series
FEATURES
Date:
Prepared by:
TYPICAL SPECIFICATIONS
• Contemporary, enduring design
The contractor will supply and install Emergi-Lite® Distinction
Series remote heads. These remote heads will consist of either
single, double or triple head configurations according to the design.
Remote heads will be constructed of durable powder coated,
Die-Cast aluminum and use MR16 halogen light sources.
The remote fixtures shall be certified to CSA C22.2 No.250.
The unit shall be Emergi-Lite® model: _______________.
• Available in 1, 2 or 3 head configurations
•Highly resistant powder-coated, Die-Cast aluminum construction
• MR16 halogen lamps: 6W, 10W, 12W, 20W, 35W and 50W
MR16 LED lamps: 4W and 5W
• CSA certified to C22.2 No. 141
DIMENSIONS
WIRE GUARDS
Dimensions are approximate and subject to change.
45/8” [11.7 cm]
5” [12.7 cm]
9 ” [24.6 cm]
5” [12.7 cm]
4” [10.2 cm]
5/8
8” [20.3 cm]
93/4” [24.9 cm]
EF150D
460.0029-E
Wall Mount (EF150)
460.0032-E
Wall Mount (EF150D)
460.0078-E
Wall Mount (EF150T)
REPLACEMENT LAMPS
EF150
41/8” [10.4 cm]
Contractor:
MODEL
LAMP TYPE
VOLTAGE-WATTAGE
580.0074-E
MR16 flood
6V-6W
580.0080-E
MR16 flood
12V-12W
580.0077-E
MR16 flood
24V-20W
580.0097-E
MR16 LED
6V-4W
580.0093-E
MR16 LED
12V-4W
580.0104-E
MR16 LED
12V-5W
580.0098-E
MR16 LED
24V-4W
580.0095-E
MR16 LED
120V-4W
580.0106-E
MR16 LED
12V-6W
For the complete list, please see the lamp chart on pages 156 to 158
EF150T
ORDERING INFORMATION
SERIES
EF150= closed
# OF HEADS
Blank= one head
D= two heads
T= three heads
COLOUR
Blank= white
-B= black
VOLTAGE/WATTAGE
-6V6W= MR16, 6V-6W
-6V10W= MR16, 6V-10W
-12V12W= MR16, 12V-12W
-12V20W= MR16, 12V-20W
-12V35W= MR16, 12V-35W
-12V50W= MR16, 12V-50W
-24V12W= MR16, 24V-12W
-24V20W= MR16, 24V-20W
-24V35W= MR16, 24V-35W
-24V50W= MR16, 24V-50W
-LAC= MR16 LED, 6V-4W
-LGC= MR16 LED, 12V-4W
-LIC= MR16 LED, 12V-5W
-LLC= MR16 LED, 24V-4W
-LJC= MR16 LED, 12V-6W
-LVC= MR16 LED, 120V-4W
-20H= MR16 IR, 12V-20W
-35H= MR16 IR, 12V-35W
-50H= MR16 IR, 12V-50W
EXAMPLE: EF150MD
146
EFR Distinction™
Series
Project/Location:
Contractor:
Date:
Recessed Designer Series
Prepared by:
TYPICAL SPECIFICATIONS
FEATURES
•Contemporary, enduring designs
The contractor will supply and install Emergi-Lite® Distinction™
Collection recessed heads and housing. Recessed heads will be
constructed of durable powder coated metal and use MR16 halogen
lamps.
The light source will be
V,
W MR16 halogen
wide beam (flood) or otherwise specified.
The remote unit shall be Emergi-Lite® model:
,
and the housing shall be Emergi-Lite® model:
.
•4W, 5W, 6W, 10W, 12W, 20W, 35W and 50W lamps
•Wide beam MR16 (flood) or LED light source
•Will blend in with regular decorative recessed fixtures
•Choice of housing for new construction or insulated ceiling
•E
FR8NB and EFR8R are made of powder coated or
electro-plate steel
• EFR9 and EFR2 are made of Die-Cast aluminum
EFR8NB
EFR9
REPLACEMENT LAMPS
EFR8R
EFR2
BACK BOXES
EL-GRHR03
Non-Insulated ceiling 6-24V
New construction
MODEL
LAMP TYPE
VOLTAGE/WATTAGE
580.0079-E
MR16
6V-10W
580.0080-E
MR16
12V-12W
580.0077-E
MR16
24V-20W
580.0104-E
MR16 LED
12V-5W
580.0106-E
MR16 LED
12V-6W
For the complete list, please see the lamp chart on pages 156 to 158
EL-GRHR04
Non-Insulated ceiling 6-24V
Renovation
EL-GRHR05
Non-Insulated ceiling 120V GU10
New construction
EL-GRHR06
Insulated ceiling 6-24V
New construction
DIMENSIONS
Dimensions are approximate and subject to change.
RENOVATION HOUSING
EL-GRH04
143
55/8”
[14.2 cm]
INSULATED CEILINGS
HOUSING EL-GRH06
NON-INSULATED CEILINGS
HOUSING EL-GRH05
5 5/8" cm]
55/8” [14.3
NEW CONSTRUCTION
HOUSING EL-GRH03
4” [10.2 cm]
71/4”
[18.4 cm]
41/2”
[14.4 cm]
4 5/8"
45/8” [11.74
cm]
117.48
6"
6”153.00
[15.3
cm]
73/4” [19.9 cm]
14” - 24” [35.6 - 60.9 cm]
1
31/2”
[8.8 cm]
4” [10.2 cm]
111/4” [28.6 cm]
4” [10.2 cm]
14” - 24” [35.6 - 60.9 cm]
47/16” [36.7 cm]
2
121/2” [31.72
cm]
317.20
12
"
ORDERING INFORMATION
SERIES
EFR=
decorative
recessed
remote
HEAD STYLE
8NB= flat
8R= concave
9= concave
2= pop-out
COLOUR
WH= white
BK= black (18R, 19 & 24 series
only)
BN= brushed nickel (8R, 8NB &
2 series only)
CH= chrome (2 series only)
PB= polished brass
(2 series only)
LAMP TYPE
R16
MR16= M
lamp
VOLTAGE/WATTAGE
-6V6W= MR16, 6V-6W
-6V10W= MR16, 6V-10W
-12V12W= MR16, 12V-12W
-12V20W= MR16, 12V-20W
-12V35W= MR16, 12V-35W
-12V50W= MR16, 12V-50W
-24V12W= MR16, 24V-12W
-24V20W= MR16, 24V-20W
-24V35W= MR16, 24V-35W
-24V50W= MR16, 24V-50W
-LIC= MR16 LED, 12V-5W
-LJC= MR16 LED, 12V-6W
-120V20W= GU10, 120V-20W*
-120V35W= GU10, 120V-35W*
-120V50W= GU10, 120V-50W*
*Available only in “8R & 9”series and with
EL-GRH06 housing
EXAMPLE: EFR8NBN-12V20W
147
Survive-All EF39
& EF39P Series
™
NEMA-4X Certified Remote Fixture
FEATURES
Project/Location:
Contractor:
Date:
Prepared by:
TYPICAL SPECIFICATIONS
• Fully gasketed with a selection of cast aluminum or
polycarbonate back plate
Supply and install Emergi-Lite® EF39P Series remote emergency
lighting fixtures. These remote fixtures will consist of either
single or double lamp configurations according to the design.
These fixtures shall be fully gasketed with a UV resistant and fire
retardant polycarbonate back plate with a clear heavy-duty UV
resistant polycarbonate lens. The unit shall be equipped with two
emergency heads with tool-less adjustable swivels (lamps of 12W
or less). Units shall be NEMA-4X and NSF certified and specifically
designed for high abuse areas, wet and cold weather locations, food
processing plants, as well in applications requiring a resistance to
corrosive agants. The standard unit will come with stainless steel
tamper-proof screws and bit.
The remote fixture shall be certified to CSA C22.2 No. 141. The
head(s) shall be fully adjustable without tools and should be
V
W.
equipped with MR16 halogen lamp(s) of
The remote unit shall be the Emergi-Lite® model:
.
• Clear polycarbonate UV and impact resistant lens
• Choice of single or double lamp models
• Available in 6, 12 and 24V models MR16 or LED
• Easy lamp replacement
• Comes standard with tamper-proof screws and bit
• NSF Certified for food processing plants
• NEMA-4X Certified*
• CSA Certified to C22.2 No. 141
• Suitable for indoor/outdoor installation
*NEMA-4X Certified when installed using a circular NEMA-4X rated junction box
(sold seperatly by Thomas&Betts under P/N CE365D-CAR or CE365DW-CAR and with
plugs P/N P7701W-CAR).
REPLACEMENT LAMPS: MR16
EF39P
NEMA-4X
ORDERING CODE
LAMP TYPE
VOLTAGE
580.0074-E
MR16 flood
6V-6W
580.0079-E
MR16 flood
6V-10W
580.0080-E
MR16 flood
12V-12W
580.0070-E
MR16 flood
24V-12W
580.0097-E
MR16 LED
6V-4W
580.0093-E
MR16 LED
12V-4W
580.0104-E
MR16 LED
12V-5W
580.0106-E
MR16 LED
12V-6W
580.0098-E
MR16 LED
24V-4W
For the complete list, please see the lamp chart on pages 156 to 158
EF39
148
ORDERING CODE
LAMP TYPE
VOLTAGE
580.0068-E
MR16 infrared
12V-20W
580.0077-E
MR16 flood
24V-20W
Survive-All™ EF39
& EF39P Series
Project/Location:
Contractor:
Date:
NEMA-4X Certified Remote Fixture
Prepared by:
DIMENSIONS
Dimensions are approximate and subject to change.
73/8” [18.7 cm]
47/8” [12.3 cm]
33/4” [9.5 cm]
ORDERING INFORMATION: EF39P
SERIES
EF39P= polycarbonate
NEMA 4X
NUMBER OF LAMPS
Blank= one lamp
D= two lamps
LAMP TYPE
M= MR16
COLOUR
Blank= factory white
-B= black
-G= grey
LAMP TYPE/VOLTAGE/WATTAGE
-6V6W= MR16, 6V-6W
-6V10W= MR16, 6V-10W
-12V12W= MR16, 12V-12W
-24V12W= MR16, 24V -12W
-LA= MR16 LED 6V-4W
-LG= MR16 LED 12V-4W
-LI= MR16 LED 12V-5W
-LJ= MR16 LED 12V-6W
-LL= MR16 LED 24V-4W
EXAMPLE: EF39PDM-B-6V6W
ORDERING INFORMATION: EF39
SERIES
EF39= Die-Cast backplate
NEMA 4X
NUMBER OF LAMPS
Blank= one lamp
D= two lamps
LAMP TYPE
M= MR16
COLOUR
Blank= factory white
-B= Black
-G= grey
EXAMPLE: EF39DM-12V20W
149
LAMP TYPE/VOLTAGE/WATTAGE
-12V20W= MR16IR, 12V-20W
-24V20W= MR16, 24V-20W
Project/Location:
EF25 Series
Contractor:
Date:
Weatherproof
Remote Fixture
FEATURES
Prepared by:
DIMENSIONS
• Quality illumination requires fewer fixtures
Dimensions are approximate and subject to change.
• Weatherproof MR16 powder coated cast aluminum light head
• Up to 24V-50W
5” [12.7 cm]
• Available single or double head
47/8” [12.4 cm]
• Preinstalled on a Red Dot weatherproof junction box:
®
- Five Outlets, 41⁄8” Diameter
61/2” [16.5 cm]
- Copper-free aluminum provides increased corrosion
resistance
41/8” [10.6 cm]
- Precision cast and machined surfaces permit safer wire
pulling
23/4” [6.9 cm]
QTY = 2
17/8” [4.7 cm]
- Clean cover edges provide good gasket sealing
63/4” [17.3 cm]
- Precision NPT threads allow trouble-free field installation for
rigid, IMC or EMT conduit
91/8” [23.3 cm]
- Deep slotted stainless steel cover screws for faster
installation
• For use with 6V, 12V or 24V DC MR16 or 12V-5W LED lamps
41/8” [10.6 cm]
171/4” [43.9 cm]
MODEL
LAMP TYPE
580.0079-E
MR16 flood
6V-10W
580.0080-E
MR16 flood
12V-12W
580.0070-E
MR16 flood
24V-12W
580.0104-E
MR16 LED
12V-5W
53/4” [14.7 cm]
REPLACEMENT LAMPS
VOLTAGE-WATTAGE
41/8” [10.6 cm]
For the complete list, please see the lamp chart on pages 156 to 158
ORDERING INFORMATION
SERIES
EF25= weatherproof
remotes
# OF HEADS
Blank= single head
D= double head
COLOUR
LAMP VOLTAGE
Blank= standard color black head/grey
junction box
-6V= 6VDC
-12V= 12VDC
-24V= 24VDC
WATTAGE
6W= MR16, 6W (6V only)
10W= MR16,10W (6V only)
12W= MR16, 12W (12&24V)
20W= MR16, 20W (12&24V)
35W= MR16, 35W (12&24V)
50W= MR16, 50W (12&24V)
20WH= MR16, IR, 20W* (12V only)
35WH= MR16, IR, 35W* (12V only)
50WH= MR16, IR, 50W* (12V only)
LI= MR16 LED, 5W (12V only)
*IR= high output lamp
EXAMPLE: EF25-6V10W
150
EF26/EF26DS/
EF26D Series
Project/Location:
Contractor:
Date:
Surface Mount
Remote Fixture
Prepared by:
FEATURES
TYPICAL SPECIFICATIONS
Remote heads EF26/EF26DS/EF26D Series shall be comprised
of one (single) or two (double or twin) 12W adjustable heads with
halogen lamps. Each lamp shall be housed in an impact-resistant
polycarbonate cube. The cube lens shall be frosted to diffuse the
light.
Heads shall provide mounting holes for installation on a standard
octogonal box.
The remote unit shall be the Emergi-Lite® model:
.
• Cubic, vandal-resistant surface-mounted fixture
• Single, double or twin cube with center body
• Frosted polycarbonate cube
• CSA certified to C22.2 No. 141
DIMENSIONS
Dimensions are approximate and subject to change.
47/8” [12.4 cm]
43/4” [12.1 cm]
57/8” [15.0 cm]43/4” [12.1 cm]
WIRE GUARDS
Wall Mount (EF26)
460.0032-E
Wall Mount (EF26D)
460.0031-E
Wall Mount (EF26DS)
REPLACEMENT LAMPS
43/4” [12.1 cm]
91/2” [24.1 cm]
143/4” [37.4 cm]
57/8” [15.1 cm]
43/4” [12.1 cm]
MODEL
LAMP TYPE
VOLTAGE/WATTAGE
570.0016-E
Mini tungsten, wedge
base
6V-9W
460.00311-E
Mini halogen (quartz),
bi-pin
6V-12W
580.0079-E
MR16, flood
6V-10W
For the complete list, please see the lamp chart on pages 156 to 158
43/4” [12.1 cm]
41/2” [11.3 cm]
460.0035-E
IN THE SAME FAMILY
DEL SERIES
P. 106-107
ORDERING INFORMATION
SERIES
EF26= single cube
EF26D= double cube
EF26DS= twin cube
LAMP STYLE
Blank= tungsten
Q= halogen
M= MR16
COLOUR
Blank= factory white
B= black
LAMP STYLE/WATTAGE
-6V9W= 6V-9W, wedge base
-12V9W= 12V-9W, wedge base
-12V18W= 12V-18W, wedge base
-24V9W= 24V-9W, wedge base
-6V8W= 6V-8W, quartz bi-pin
-6V12W= 6V-12W, quartz bi-pin
-12V8W= 12V-8W, quartz bi-pin
-12V12W= 12V-12W, quartz bi-pin
-12V20W= 12V-20W, quartz bi-pin
-24V20W= 24V-20W, quartz bi-pin
-6V6W= MR16, 6V-6W
-6V10W= MR16, 6V-10W
-12V12W= MR16, 12V-12W
-12V20W= MR16, 12V-20W
-12V35W= MR16, 12V-35W
-12V50W= MR16, 12V-50W
-24V20W= MR16, 24V-20W
-24V35W= MR16, 24V-35W
-24V50W= MR16, 24V-50W
-LA= MR16 LED, 6V-4W
-LG= MR16 LED, 12V-4W
-LI= MR16 LED, 12V-5W
-LL= MR16 LED, 24V-4W
EXAMPLE: RSQBT6V9W
151
-LJ= MR16 LED, 12V-6W
-24V18W= 24V-18W,
wedge base
U10
-120V20W= G
120V-20W
U10
-120V35W= G
120V-35W
OPTIONS
Blank= no options
TP= tamper-proof screws
690.0454-E= t amper-proof
bit*
*One bit per order
Project/Location:
Contractor:
EF11 Series
Date:
Remote Fixture
Prepared by:
FEATURES
WIRE GUARDS
•A
vailable in single, double or triple head fixtures
•D
urable thermoplastic construction suitable for industrial or
high abuse areas
460.0035-E
Wall Mount (EF11)
460.0082-E
Wall Mount (EF11D)
REPLACEMENT LAMPS
• Tool-less adjustment and aiming of lamp heads
• Certified CSA C22.2 No.141
• Weatherproof
MODEL
LAMP TYPE
VOLTAGE-WATTAGE
570.0016-E
Tungsten
6V-9W
570.0025-E
Tungsten
12V-9W
570.0079-E
Tungsten
24V-9W
For the complete list, please see the lamp chart on pages 156 to 158
DIMENSIONS
Dimensions are approximate and subject to change.
43/4” [12.0 cm]
33/4” [9.5 cm]
121/2” [31.8 cm]
71/4” [18.3 cm]
33/4” [9.4 cm]
51/2” [14.0 cm]
71/4” [18.3 cm]
121/2” [31.8 cm]
41/4” [10.7 cm]
41/4” [10.7 cm]
41/4” [10.7 cm]
ORDERING INFORMATION
SERIES
LAMP STYLE
COLOUR
EF11= s ingle, PAR
36
EF11D= double, PAR
36
EF11T= t riple, PAR
36
Blank= tungsten
Q= halogen
Blank= black
W= factory white
VOLTAGE/WATTAGE
-6V9W= tungsten, 6-9W, wedge base
-6V__W= tungsten, 6V-18 or 25W, D.C.B.
-12V__W= tungsten, 12V-9 or 18W, wedge base
-12V25W= tungsten, 12V-25W, D.C.B.
-24V__W= tungsten, 24V-9 or 18W, wedge base
-24V25W= tungsten, 24V-25W, D.C.B.
-6V__W= halogen, 6V-8, 12 or 20W, quartz bi-pin
-12V__W= halogen, 12V-8, 12, 20 or 55W, quartz bi-pin
-24V__W= halogen, 24V-20 or 70 W, quartz bi-pin
-6V__W= tungsten, 6V-8, 12, 18 or 25W, sealed beam
-12V__W= tungsten, 12V-12, 18 or 25W, sealed beam
-6V__W= halogen, 6V-8,12 or 20W, quartz sealed beam
-12V__W= halogen, 12V-8, 12 or 37W, quartz sealed beam
-32V__W= tungsten, 32V-18 or 25W, D.C.B.
-120V__W= tungsten, 120V-10, 15 or 30W, D.C.B.
-120V__W= halogen, 120V-35 or 50W, D.C.B.
*NOTE: “__”= insert wattage required
EXAMPLE: EF11Q-12V12W
152
OPTIONS
FP= teflon coated lens
Project/Location:
Contractor:
EF30 Series
Date:
Remote Fixture
Prepared by:
FEATURES
REPLACEMENT LAMPS
• S ealed beam, surface-mounted, rubber coated industrial
remote fixture
• For use in high pressure hose down areas
MODEL
LAMP TYPE
VOLTAGE-WATTAGE
550.0026-E
Tungsten
12V-12W
• Available only in black
550.0027-E
Tungsten
12V-18W
• C ertified CSA C22.2 No.141
550.0023-E
Tungsten
12V-25W
*Lamps for RS10QWPBH.
For the complete list, please see the lamp chart on pages 156 to 158
DIMENSIONS
Dimensions are approximate and subject to change.
EF30
51/2” [14.1 cm]
131/2” [34.3 cm]
73/4” [19.7 cm]
71/2” [18.9 cm]
55/8” [14.4 cm]
127/8” [32.7 cm]
6” [15.2 cm]
47/8” [12.2 cm]
EF45
41/4” [10.7 cm]
41/4” [10.7 cm]
41/4” [10.7 cm]
41/4” [10.7 cm]
TUNGSTEN SEALED BEAM
HALOGEN QUARTZ, H3
ORDERING INFORMATION
SERIES
EF30= single PAR 36
EF30D= double, PAR 36
LAMP STYLE
S= sealed beam
H= quartz sealed beam
VOLTAGE
-6V__W= tungsten, 6V - 8, 12, 18 or 25W, sealed beam
-12V__W= tungsten, 12V - 12, 18 or 25W, sealed beam
-6V__W= halogen, 6V - 8, 12 or 20W, quartz sealed beam
-12V__W= halogen, 12V - 8, 12 or 37W, quartz sealed beam
OPTIONS
FP= teflon coated lens
*NOTE: “__”= insert wattage required.
EXAMPLE: EF305-6V9W
ORDERING INFORMATION
SERIES
EF45Q= single
ouble
EF45DQ= d
LAMP STYLE
S= sealed beam
H= quartz sealed beam
VOLTAGE
-12V55W= halogen, 12V - 55W, H3
-24V70W= halogen, 24V - 70W, H3
*NOTE: “__”= insert wattage required.
EXAMPLE: EF45QS-12V55W
153
OPTIONS
FP= teflon coated lens
Project/Location:
Contractor:
EF41 Series
Date:
Hazardous Location
Prepared by:
FEATURES
TYPICAL SPECIFICATIONS
• Quality illumination requires fewer fixtures
Supply and install Emergi-Lite® EF41 Series remote emergency
lighting fixture. The fixture shall have a single- or double-lamp
configuration (as specified) and shall include a fully gasketed
Die-Cast aluminum back plate and a clear heavy-duty UV resistant
polycarbonate cover. The fixture shall come standard with a 4”
octagonal box, stainless steel tamper-proof screws and dedicated
screwdriver bit.
• Certified Class I Zone 2, Groups IIA, IIB and IIC
• Certified Class I Division 2, Groups A, B, C and D as per CSA C22.2
No.137-M1981
• Temperature Codes: T3B (10W and 12W MR16 lamps) and T2C
(20W MR16 lamps), as per Canadian Electrical Code, Part I and
CSA C22.2 No.137-M1981)
The fixture shall be certified for use in hazardous locations Class I,
Division 2, Groups A, B, C and D and shall be listed to CSA C22.2
No. 141 and CSA C22.2 No.137-M1981. The fixture shall be rated
with a temperature code for the selected lamps as in the table
below.
• Extreme operational temperature range: -40ºC to +40ºC.
• Choice of single- or double-lamp models
• High-efficacy MR16 halogen lamps of 10W, 12W and 20W (see
specification table)
Each lamp in the fixture shall be able to be oriented without tools
and should be equipped with MR16 halogen lamp(s) of
V
W.
• Input voltage: 6V, 12V, 24V or 120V
• Fully gasketed Die-Cast aluminum back plate
• Clear polycarbonate cover, UV and impact resistant
The remote unit shall be Emergi-Lite® model:
• Easy installation on a 4” octagonal box (included)
.
• Comes standard with tamper-proof screws and bit
• Meets or exceeds CSA 22.2 No.141
DIMENSIONS
REPLACEMENT LAMPS
Dimensions are approximate and subject to change.
MODEL
LAMP TYPE
VOLTAGE/
WATTAGE
TEMPERATURE
CODE
580.0079-E
MR16 Flood
6V-10W
T3B (Max. 165oC)
580.0068-E
MR16-IR
Flood
(high output)
12V-20W-H
T2C (Max. 230oC)
580.0077-E
MR16 Flood
24V-20W
T2C (Max. 230oC)
580.0080-E
MR16 Flood
12V-12W
T3B (Max. 165oC)
580.0070-E
MR16 Flood
24V-12W
T3B (Max. 165oC)
57/8” [14.9 cm]
71/8” [18.1 cm]
JUNCTION
REMOTE
BOX
FIXTURE
3/4
3 ” [9.5 cm] 21/8” [5.4 cm]
45/8” [11.7 cm]
ø 4” JUNCTION
BOX
For the complete list, please see the lamp chart on pages 156 to 158
ORDERING INFORMATION
SERIES
EF41
NUMBER OF LAMPS
Blank= one lamp
D= two lamps
LAMP TYPE
COLOUR
M= MR16
MH= MR16 high output (12V-20W only)
EXAMPLE: EF41M-G-6V10W
154
-G= grey
VOLTAGE/WATTAGE/LAMP TYPE
-6V10W= MR16, 6V-10W
-12V12W= MR16, 12V-12W
-12V20W= MR16, 12V-20W
-24V12W= MR16, 24V-12W
-24V20W= MR16, 24V-20W
-12/20H= MR16 high output, 12V-20W
Project/Location:
Contractor:
EFXPR Series
Date:
Hazardous Location
Prepared by:
FEATURES
TYPICAL SPECIFICATIONS
Supply and install the Emergi-Lite® EFXPR Series of hazardous
location remote heads. The head housing will be Die-Cast aluminum
with grey epoxy powder coat finish. The lens shall be a clear, impact
and heat resistant prismatic glass globe. The head shall be factory
sealed. External seals shall not be required.
The remote shall come complete with a _____ mounting connection
and include _____lamp(s) rated _____ V ______ W.
The remote head shall be suitable for Class _____, Division _____,
Group _____ .
The remote unit shall be Emergi-Lite® model:
.
• CSA Certified for use in hazardous locations:
- Class I, Divisions 1 and 2, Groups A, B, C, D
- Class II, Divisions 1 and 2, Groups E, F, G
- Class III, Divisions 1 and 2
• Die-Cast aluminum body with grey epoxy powder coat finish
• Clear, impact and heat resistant prismatic glass globe
• Available in 6, 12 and 24V
• Available with single-lamp or twin-lamp combination
•New, easy-to-build catalogue number based on the
Emergi-Lite® Severity Codes
REPLACEMENT LAMPS
• Meets or exceeds CSA 22.2 No.141
MODEL
TYPE
6V-12W
580.0015-E
12V-12W
Halogen
580.0027-E
DIMENSIONS
VOLTAGE/WATTAGE
580.0011-E
12V-20W
580.0023-E
24V-20W
Dimensions are approximate and subject to change.
WALL MOUNT
7” [17.8cm]
293/4” [75.6cm]
115/8” [29.5cm]
6” [15.3 m]
151/4” [38.8 cm]
7” [17.8 cm]
26 ” [67.9cm]
91/8” [23cm]
95/8” [24.3cm]
35/8” [9.3cm]
177/8” [45.5cm]
91/8” [23 cm]
17/8” [4.8cm]
3/4
3” [7.7cm]
103/4” [27.3cm]
4” [10.1cm]
PENDANT MOUNT
6” [15.3cm]
25 ” [64 cm]
71/4”
[18.4cm]
135/8” [34.6cm]
6” [15.3cm]
71/4” [18.4cm]
1/4
33/8” [8.4cm]
93/8” [23.8cm]
141/8” [35.9cm]
95/8” [24.5cm]
21” [53.3 cm]
71/4” [18.4cm]
SEVERITY S3, S4
6” [15.3cm]
CEILING MOUNT
51/4” [13.3cm]
71/8” [18.1cm]
115/8” [29.5cm]
SEVERITY S1, S2
DOUBLE PENDANT MOUNT
7” [17.8 cm]
251/8” [63.7 cm]
1.
2.
ENVIRONMENT
SEVERITY CODE
Cl. I, Div. 1, Gr. B
S1
Severity Code
CERTIFICATION GUIDE FOR REMOTE LIGHTING FIXTURES (40°C AMBIENT)
Cl. I, Div. 1, Gr. C, D
S2
Temperature Code
T4A
T6
T1
T3C (E.G.F.)
CI. I, Div. 2, Gr. B, C, D
S3
CSA/UL rating
Max. 120°C (248°F)
Max. 85°C (185°F)
Max. 450°C (842°F)
Max. 165°C (329°F)
S1
S2
S3
S4
ORDERING INFORMATION
SERIES
MOUNTING
EFXPR
C= ceiling mount
P= pendant mount
W= wall mount
NUMBER OF LAMPS
11= single remote, one lamp
12= single remote, two lamps
21= double remote, one lamp*
*Pendant mount only.
SEVERITY CODE
VOLTAGE
S1= CL.1, Div.1, Gr.A, B
S2= CL.1, Div.1, Gr.C, D
S3= CL.1, Div.2, Gr.A, B, C, D
S4= CL.2, Div.1,&2, Gr.E, F, G CL3, Div. 1&2
-6V= 6V
-12V= 12V
-24V= 24V
-120V= 120V
EXAMPLE: EFXPRP11S3-6V12W
155
LAMP WATTAGE/TYPE
12W= halogen, 6V, 12V-12W,
quartz bi-pin
20W= halogen, 12, 24V-20W,
quartz bi-pin
Project/Location:
Contractor:
Lamp Chart
LAMP TYPE
CODE
VOLTAGE
A
MR16 halogen lamps
MR16, LED
lamps
par 36,
Sealed beam
halogen lamps
par 36,
Sealed beam
lamps
t-3 1/4, Xenon
lamps
6V - 6W
Prepared by:
LUMEN
LUXRAY
580.0074-E
Date:
B
40
EF40
LITRAY
A
B
7’
1’
A
B
RETRACT-A-LITE
A
B
EF9 / Q /M
A
B
8’
3’
580.0079-E
6V - 10W (flood)
77
21’
20’
X
X
23’
22’
580.0080-E
12V - 12W (flood)
135
25’
17’
16’
-
31’
19’
31’
19’
54’
41’
36’
-
53’
39’
53’
39’
580.0075-E
12V - 20W*
270
580.0064-E
12V - 20W (flood)
245
50’
36’
65’
50’
580.0068-E 12V - 20WH (flood)
417
70’
54’
70’
54’
580.0090-E 12V - 35WH (flood)
853
130’
110’
130’
110’
171’
580.0089-E 12V - 50WH (flood)
1550
160’
171’
160’
580.0083-E
12V - 35W (flood)
490
96’
86’
96’
86’
580.0076-E
12V - 50W (flood)
785
126’
100’
126’
100’
38’
25’
15’
25’
580.0077-E
24V - 20W (flood)
240
46’
37’
X
X
48’
580.0070-E
24V - 12W (flood)
95
22’
13’
X
X
25’
15’
580.0084-E
24V - 35W (flood)
460
76’
60’
580.0078-E
24V - 50W (flood)
875
139’
12’
580.0065-E
120V - 20W (flood)
100
580.0066-E
120V - 35W (flood)
230
580.0067-E
120V - 50W (flood)
460
580.0097-E
6V - 4W
580.0093-E
12V - 4W
580.0104-E
12V - 5W
26’
17’
130
35’
23’
X
X
X
X
38’
170
39’
23’
28’
-
41’
25’
41’
25’
340
71’
56’
71’
56’
71’
56’
71’
56’
41’
52’
X
X
52’
41’
52’
41’
100’
85’
100’
85’
100’
85’
100’
85’
580.0098-E
24V -4W
200
580.0095-E
120V - 4W
200
580.0106-E
12V - 6W
510
EF18 / D / T
A
B
550.0036-E
6V - 8W
155
X
X
550.0037-E
6V - 10W
190
X
X
550.0021-E
6V - 20W
380
68’
55’
550.0024-E
12V - 8W
130
25’
18’
37’
550.0025-E
12V - 12W
240
45’
550.0030-E
6V - 12W
225
X
X
550.0018-E
6V - 8W
130
17’
14’
550.0016-E
6V - 18W
270
29’
18’
550.0017-E
6V - 25W
400
75’
48’
550.0026-E
12V - 12W
190
31’
23’
550.0027-E
12V - 18W
210
31’
19’
68’
43’
X
X
550.0023-E
12V - 25W
395
570.0213-E
6V - 6W
120
17’
-
570.0214-E
6V - 10W
180
25’
18’
570.0215-E
12V - 6W
105
X
X
570.0216-E
12V - 10W
200
X
X
570.0211-E
24V - 12W
240
A= TYPICAL SPACING 7’ MOUNTING 6’ WIDE
B= TYPICAL SPACING 15’ MOUNTING 6’ WIDE
TYPICAL SPACING IS BASED ON A 6” WIDE PATH AND 80.50.20 REFLECTANCES.
156
Project/Location:
Contractor:
Date:
Prepared by:
EF26 / DS / D
DISTINCTION
A
B
A
X
X
X
X
X
X
31’
EFR
EF15
B
A
B
8’
3’
X
23’
22’
X
19’
31’
A
EF11
B
EF30
A
EF25
B
A
EF39
B
A
EF41
A
B
B
A
B
X
X
X
X
X
X
X
X
X
X
160’
171’
21’
20’
19’
X
X
31’
19’
21’
20’
25’
17’
25’
X
X
17’
X
X
53’
39’
53’
39’
53’
39’
50’
36’
X
X
70’
54’
70’
54’
70’
54’
65’
50’
X
X
130’
110’
130’
110’
130’
110’
X
X
X
X
160’
171’
160’
171’
160’
171’
X
X
96’
86’
96’
86’
96’
86’
X
X
126’
100’
126’
100’
126’
100’
X
X
X
X
48’
38’
X
X
48’
38’
46’
37’
X
X
21’
20’
X
25’
15
X
X
25’
15’
22’
13’
X
X
76’
60’
X
X
X
X
76’
60’
X
X
X
X
139’
12’
X
X
139’
112
X
X
28’
19’
X
X
26’
17’
42’
38’
X
X
X
X
65’
58’
X
X
X
X
X
X
38’
25’
38’
25’
X
X
X
X
41’
25’
41’
25’
X
X
71’
56’
71’
56’
71’
56’
71’
56’
X
X
52’
41’
52’
41’
X
X
43’
39’
100’
85’
100’
85’
100’
85’
100’
85’
Consult
your sales
representative
X
X
X
X
X
X
X
X
68’
55’
68’
55’
68’
55’
25’
18’
25’
18’
25’
18’
45’
37’
45’
37’
45’
37’
X
X
X
X
17’
14’
17’
14’
17’
14’
29’
18’
29’
18’
29’
18’
75’
48’
75’
48’
75’
48’
31’
23’
31’
23’
31’
23’
68’
43’
X
X
X
X
68’
43’
68’
43’
A= TYPICAL SPACING 7’ MOUNTING 6’ WIDE
B= TYPICAL SPACING 15’ MOUNTING 6’ WIDE
TYPICAL SPACING IS BASED ON A 6” WIDE PATH AND 80.50.20 REFLECTANCES.
157
Project/Location:
Contractor:
Lamp Chart
LAMP TYPE
CODE
VOLTAGE
Date:
Prepared by:
LUMEN
PROVIDER®
A
B
EF9 / Q / M
A
EF18 / D / T
B
EF15
EF26 / DS / D
A
EF30
A
B
A
B
A
B
570.0040-E
24V - 18W
250
X
X
X
X
X
X
570.0037-E
6V - 18W
300
10’
-
10’
-
10’
-
570.0031-E
S8, High intensity
tungsten lamps 570.0061-E
double contact
570.0120-E
bayonet base
12V - 25W
400
X
X
X
X
X
X
24V - 25W
400
X
X
X
X
X
X
120V - 15W
94
X
X
16’
5’
X
X
570.0025-E
12V - 9W
138
X
X
X
X
X
570.0020-E
6V - 13W
188
570.0011-E
12V - 9W
126
570.0038-E
6V - 25W
400
X
X
X
X
X
X
RP-11, High
570.0022-E
intensity tungsten
lamps
570.0030-E
double contact
bayonet base
570.0058-E
12V - 13W
188
X
X
X
X
X
X
12V - 18W
276
X
X
X
X
X
X
X
x
B
EF11
x
A
EFXPR
B
A
B
24V - 9W
75
X
X
X
X
X
580.0012-E
6V - 6W
113
X
X
X
X
X
X
X
X
580.0017-E
6V - 10W
200
X
X
X
X
X
X
X
X
580.0013-E
6V - 8W
163
23’
14’
17’
14’
17’
14’
17’
14’
17’
14’
580.0011-E
6V - 12W
240
23’
16’
15’
12’
15’
12’
15’
12’
15’
12’
X
X
580.0022-E
6V - 20W
400
23’
17’
23’
17’
23’
17’
X
X
580.0014-E
12V - 8W
163
24’
17’
16’
13’
16’
13’
16’
13’
16’
13’
580.0015-E
12V - 12W
276
X
X
20’
15’
20’
15’
20’
15’
20’
15’
X
X
580.0023-E
24V - 20W
133
21’
15’
21’
15’
21’
15’
21’
15’
X
X
580.0016-E
12V - 14W
300
X
X
X
X
X
X
580.0027-E
12V - 20W
314
34’
26’
34’
26’
34’
26’
X
X
H3, Incandescent lamp 580.0030-E
wedge base
12V - 55W
748
108’
78’
580.0031-E
24V - 70W
791
104’
74’
570.0026-E
6V - 7.2W
100
X
X
X
X
X
570.0016-E
6V - 9W
150
X
X
12’
5’
12’
-
570.0025-E
12V - 9W
138
X
X
14’
8’
18’
13’
570.0028-E
12V - 12W
150
x
x
T-2 1/4, Bi-pin
halogen lamps
T-2 3/4,
Bi-pin
halogen
lamps
570.0029-E
12V - 18W
264
T-5, Incandescent 570.0045-E
lamp wedge base
570.0046-E
24V - 9W
113
24V - 18W
240
570.0012-E
6V - 5.4W
68
X
X
X
34’
26’
X
X
X
X
X
X
12’
-
18’
13’
12’
-
12’
-
18’
13’
18’
13’
X
X
X
X
12’
14’
18’
12’
18’
12’
18’
12’
18’
12’
2’
15
9’
15’
9’
15’
9’
15’
9’
21’
10’
21’
15’
21’
15’
21’
15’
21’
15’
X
X
X
X
X
X
A= TYPICAL SPACING 7’ MOUNTING 6’ WIDE
B= TYPICAL SPACING 15’ MOUNTING 6’ WIDE
74’
108’
74’
X
24’
X
104’
TYPICAL SPACING IS BASED ON A 6” WIDE PATH AND 80.50.20 REFLECTANCES.
158
Project/Location:
Contractor:
Date:
Prepared by:
Glossary
FP
Food Proccessing
A protective teflon coating that is applied to the glass lens of a lighting fixture to prevent broken
shards from falling if the glass is accidently broken or vandalised.
TP
Tamper-proof screws*
Screws that require a special bit. Can be used on certain units to deny access to unauthorized
personnel.
*Only applicable to remotes
159
CENTRAL
SYSTEMS
UNITY
SERIES
CHSERIES
AC INVERTERS
CENTRAL
SYSTEMS
161
Project/Location:
Contractor:
TABLE OF CONTENTS
Date:
Prepared by:
Project/Location:
Project/Location:
Contractor:
What is Emex?
Date:
A General Presentation about Emex Central Systems
Prepared by:
A General Presentation about Emex Central Systems
True Sine Waveform
Using a solid-state, pulse width modulation (PWM) inverter, the
systems produce pure sinusoidal output waveform with less than 5%
Total Harmonic Distortion (THD) for linear loads.
Reliability
The product is third generation inverter technology. LVD (Low Voltage
Disconnect) circuitry eliminates excessive battery drain after long
power outages.
Batteries
Automatic restart and recharge upon restoration of utility.
Each module has input and output protection and each module
measures and limits its own current.
Alarms and status indications are provided on the front panel display,
which provide clear and concise information, rather than a long list of
parameters, which may be confusing.
This is because an Emergency Lighting system has unique load
characteristics. And since Emergency Lighting is a critical life-safety
installation, it is vital that a Central Battery System is designed with
these load characteristics in mind. EMEX Power central inverter
systems are specifically designed to provide emergency power for
emergency lighting systems in a power failure.
Approvals
- CSA C22.2 No. 141-10 – Emergency Lighting Equipment
- CSA C22.2 No. 107.3 – Uninterruptible Power Systems
- UL 1778 – Uninterruptible Power Systems
Applications
SERIES HIGHLIGHTS
EMEX-Power Systems can be used in almost every type of
building, especially in architecturally sensitive applications or
when maintenance costs and testing of individual unit equipment
becomes significant. Our systems are designed to work with power
factor corrected as well as the most recent T5 and T5-HO electronic
ballasts.
Performance
The EMEX-Power Systems work with lighting loads to provide
full light output for minimum 30 min. It is designed to support
incandescent, fluorescent and LED loads. It will power these loads at
cold starts for all normally off circuits or normally on circuits.
FEATURES
BENEFITS
SELF-DIAGNOSTIC/SELF-TESTING
Programmable monthly and annual self-testing. Proven selfdiagnostic with information stored in separate memory logs for
Test, Event and Alarm. Microprocessor monitoring and control.
In choosing the right AC system to support
emergency lighting it is important to consider
the following questions:
General information on UPS systems:
Recharge period
UPS systems which are designed primarily for computer back-up
generally offer short run times, 5 or 10 minutes. The long run
times required for emergency lighting call for more powerful
chargers to recharge the larger bank of batteries needed in the
time prescribed by CSA.
Overload performance
Overload performance
Is the system able to start the full load without the mains supply
present. How does the system perform in a total power failure (ie
is the system able to start the load without the bypass supply being
available)?
Repeat duty
An emergency lighting load will impose large “in-rush” currents
when starting lamps from cold. However, UPS systems are
often designed to shut down at only 125% overload and revert to
the incoming supply. During a total power failure situation, this
could result in total failure of the emergency lighting system.
Furthermore, a UPS may fail to clear a breaker on a lighting
circuit, meaning that a single short circuit fault could result in loss
of the entire emergency lighting supply.
Energy consumption and battery life
Most UPS systems operate in the “on-line” mode, whereby the
inverter runs constantly to supply the load, and power is taken
from the battery with the charger running constantly. This places
an excessive ripple on the battery (contrary to the advice given
by most battery manufacturers). Also, the system is constantly
generating heat which has a further detrimental effect on battery
life. There are energy costs and heat generation issues must be
addressed when running an on-line system.
CSA141-10 requires a central battery system to fully recharge within
24 hours. Is the charger able to recharge the batteries quickly (80%
in 14 hours or 100% after 24 hours)?
Energy consumption and heat dissipation
Are the inverter and charger permanently running, shortening
the battery life, generating heat, wasting energy and shortening
component life? Are cooling fans running continuously, generating
noise?
Maintenance
Is the system easy to service and maintain? Is the system designed
in a modular format, or would the failure of even a minor component
require the whole system to be shut down and stripped for repair?.
Contractor:
Contractor:
What is Emex?
Date:
SYSTEM DESIGN
The EMEX Power inverter and charger modules utilize solid state
electronics of the highest reliability to provide a rugged, easy to
maintain system with exceptional performance for emergency
lighting use. The system has been designed solely for emergency
lighting, and not modified from other less essential power supply
requirements. As such, the system has exceptional overload
performance without the need to over-specify the rating of the
inverter to ensure faults can be cleared.
COMPLIANCE WITH NFPA101
The self-testing meets the requirements of NFPA and UL. User
programmable time of testing. Test results, events or alarms
can be downloaded from history logs. Load monitoring. Reduced
testing/service time.
What is Emex?
Date:
Prepared by:
A General Presentation about Emex Central Systems
SYSTEM DESIGN
FEATURES
COMPLIANCE WITH NFPA101
The self-testing meets the requirements of NFPA and UL. User
programmable time of testing. Test results, events or alarms
can be downloaded from history logs. Load monitoring. Reduced
testing/service time.
LESS AIR-CONDITIONING
Reduced costs for air-conditioning required to ensure the optimum
operating temperature when compared with equivalent systems
that dissipate much more heat. Higher reliability of fans and
electronic components.
VERSATILE INSTALLATION
Modular design, easy front access freestanding cabinets,
fasten together when more than one cabinet is required.
Optional seismic kit available. All wiring provided is pre-cut
and terminated, along with the necessary hardware for proper
installation.
EASY TO INSTALL
Quick installation and connection through flexible cable entries and
fast access terminal blocks. Low MTTR (<30 min.) due to modular
design, quick disconnect means and frontal access.
COMPLETE PROTECTION
Battery circuit breakers are standard. Modular standard systems
offer overload capacity, short-circuit protection, current- limiting,
low-battery disconnect and brownout protection as standard.
REDUCED DAMAGE RISKS
The full protection of the system will eliminate damage created by
external events and will increase lifetime of the electronics and the
batteries.
COMPLETE PROTECTION
Battery circuit breakers are standard. Modular standard systems
offer overload capacity, short-circuit protection, current- limiting,
low-battery disconnect and brownout protection as standard.
REDUCED DAMAGE RISKS
The full protection of the system will eliminate damage created by
external events and will increase lifetime of the electronics and the
batteries.
INCREASED MTBF
Increased reliability and reduced preventative maintenance. No air
filters needed.
EASY MAINTENANCE
Diagnostics, troubleshooting, preventative maintenance and
service are made easier by using the front panel display or the
history logs.
• LCD display
• Maintenance free standard batteries
• Forced air cooling during emergency and recharge mode only
• Off when on standby
INCREASED MTBF
Increased reliability and reduced preventative maintenance. No air
filters needed.
THERMAL PERFORMANCE
Bonded oversized heat sinks for maximum thermal performance.
Cooling fans are energized only in inverter and recharge modes.
MONITORING AND CONTROL
User friendly programmable interface with LCD display provides
full metering values, easy program and control functions and a
wide range of visual and audible alarms.
EASY MAINTENANCE
Diagnostics, troubleshooting, preventative maintenance and
service are made easier by using the front panel display or the
history logs.
MAX. INPUT
CURRENT (A)(1)
HEAT LOSS IN
EFFIC.
NORMAL MODE
AT FULL
(BTU/HR)
LOAD % 120V 240V 277V 347V
3.0
6.0
9.0
98%
98%
98%
42
67
92
21
33
46
18
29
40
14
23
32
546
BATT.
VDC
120
546
120
546
120
BATT.
ADC
34
68
101
NO. OF
BATT.(1)
10
20
10
IPS CABINET
DIMENSIONS
W”
30
30
30
H”
71
71
71
BATT. CABINET
DIMENSIONS
D”
NO. OF
BATT.
CAB.(1)(2)
W”
H”
D”
27
NA
NA
NA
NA
27
NA
NA
NA
NA
27
NA
NA
NA
NA
IPS
CABINET
WEIGHT
KG(1)
240
290
340
BATT.
TOTAL
BATTERY
CABINET
SYSTEM
WEIGHT
WEIGHT KG
WEIGHT
KG(1)
KG(1)
(EMPTY)(1)
NA
NA
NA
105
210
372
345
500
712
12.0
98%
117
58
51
40
546
120
135
20
30
77
27
1
30
77
27
390
140
550
1080
15.0
98%
142
71
61
49
546
120
168
20
30
77
27
1
30
77
27
440
140
550
1130
1- For 30 min. discharge time. For other discharge times, consult factory.
2- Batteries are installed in the IPS cabinet for 3 to 9.0KVA systems, for 30 minutes only.
• Small profile, compact white lighting is ideal for
architectural applications.
• Vibration-resistant LED stands up to industrial
environments.
• Ideal for indoor and outdoor use.
340-LUMEN 5W MR16 LED
200-LUMEN 4W MR16 LED
Keeping pace with technology, in 2012 we introduced a
12V-5W MR16 LED lamp. With a typical luminous flux of 340
lumens, this lamp has the same lighting performance as
a 20W high-output halogen MR16. A twin emergency head
installed at a height of 7.5ft illuminates more than a 70ft
path of egress.
Keeping pace with technology, in 2012 we introduced a
12V-5W MR16 LED lamp. With a typical luminous flux of 340
lumens, this lamp has the same lighting performance as
a 20W high-output halogen MR16. A twin emergency head
installed at a height of 7.5ft illuminates more than a 70ft
path of egress.
Leading the technology trend, Emergi-Lite® offers a
complete series of 4W MR16 LED lamps available for all
the standard battery voltages: 6V, 12V, 24V and 120V. With
up to 30,000 hours of operational life and a luminous
flux of typically 200 lumens, they are available with most
emergency heads designed to hold an MR16 lamp and meet
the majority of illumination specifications. For example: one
pair of LED emergency heads installed at a height of 7.5ft,
illuminates a 6ft by 40ft path of egress.
510-LUMEN 6W MR16 LED
New in Fall 2013, we intoduce a 12V - 6W MR16 LED lamp,
which offer typical luminous flux of 510 lumens. Like the
lower wattage MR16 LED lamps, this new lamp is specially
designed for emergency lighting. It offers the same lighting
preformance as the 35W or 20W Mr16 IR. A twin emergency
head installed at a height of 7.5’ illuminates approximately
100’ path of egress.
Compared to halogen lamps (16-20W), these 4W MR16
LED lamps illuminate the same area of egress during an
emergency situation by using 75% less power. This has
a direct impact on the battery size, reducing the back-up
capacity needs by 75%. Consequently, it also reduces the
total cost of the application, with the use of smaller battery
capacity units, the possibility of using fewer fixtures due to
superior illumination, thus also reducing electrical wiring,
and it it reduces the environmental footprint.
• Small profile, compact white lighting is ideal for
architectural applications.
• = lamp efficacy: 50 - 70 lumen per watt compared to 15 30 lumen per watt of the best halogen lamp.
• = lower lamp temperature (80 - 120°C) is a huge benefit
for lighting in hazardous locations.
340-LUMEN 5W MR16 LED
200-LUMEN 4W MR16 LED
• Reduces required battery capacity by 75%, providing
necessary illumination with fewer remote heads and
battery units for project cost savings.
• = operational life: 30,000+ hours, equivalent to a lifetime
warranty in emergency lighting.
• Ideal for indoor and outdoor use.
Leading the technology trend, Emergi-Lite® offers a
complete series of 4W MR16 LED lamps available for all
the standard battery voltages: 6V, 12V, 24V and 120V. With
up to 30,000 hours of operational life and a luminous
flux of typically 200 lumens, they are available with most
emergency heads designed to hold an MR16 lamp and meet
the majority of illumination specifications. For example: one
pair of LED emergency heads installed at a height of 7.5ft,
illuminates a 6ft by 40ft path of egress.
• CSA C22.2 No. 141 certified.
• Energy-efficient LED MR16 lamp provides equivalent
lighting performance to a much higher watt halogen
MR16 lamp.
Extremely efficient and long-lasting, LED lamps become the
natural alternative to incandescent lamps due to three main
advantages:
• Vibration-resistant LED stands up to industrial
environments.
• = operational life: 30,000+ hours, equivalent to a lifetime
warranty in emergency lighting.
• = lower lamp temperature (80 - 120°C) is a huge benefit
for lighting in hazardous locations.
ELECTRICAL/MECHANICAL CHARACTERISTICS FOR 30 MINUTES BACK-UP TIME
POWER
RATING
KVA/KW
Date:
MR16 LED LAMP BENEFITS
With the remarkable technology development in the last
decade, the light-emitting diode (LED) is becoming the
preferred solution in low- and medium-power lighting
applications. The emergency lighting industry is no
exception: today virtually every new product introduced to
market includes “white” LEDs for emergency illumination.
• Reduces required battery capacity by 75%, providing
necessary illumination with fewer remote heads and
battery units for project cost savings.
• = lamp efficacy: 50 - 70 lumen per watt compared to 15 30 lumen per watt of the best halogen lamp.
• 30, 60, 90, 120 minutes run times
• Summary alarm form C dry contact
• Generator compatibility
• Electronic and magnetic ballast compatible
BENEFITS
SELF-DIAGNOSTIC/SELF-TESTING
Programmable monthly and annual self-testing. Proven selfdiagnostic with information stored in separate memory logs for
Test, Event and Alarm. Microprocessor monitoring and control.
LOW HEAT DISSIPATION
Very low heat loss in standby operating mode (see specifications
for exact values). Convection cooling in normal mode with forced
air during emergency and recharge mode. Battery cabinets:
convection cooling only.
EASY TO INSTALL
Quick installation and connection through flexible cable entries and
fast access terminal blocks. Low MTTR (<30 min.) due to modular
design, quick disconnect means and frontal access.
Contractor:
Project/Location:
MR16 LED EMERGENCY LIGHTING
Prepared by:
MR16 LED ILLUMINATION
MR16 LED LAMP BENEFITS
• CSA C22.2 No. 141 certified.
• Energy-efficient LED MR16 lamp provides equivalent
lighting performance to a much higher watt halogen
MR16 lamp.
Extremely efficient and long-lasting, LED lamps become the
natural alternative to incandescent lamps due to three main
advantages:
• Automatic event, test and alarm log
EMEX-Power Systems can be used in almost every type of
building, especially in architecturally sensitive applications or
when maintenance costs and testing of individual unit equipment
becomes significant. Our systems are designed to work with power
factor corrected as well as the most recent T5 and T5-HO electronic
ballasts.
Performance
The EMEX-Power Systems work with lighting loads to provide
full light output for minimum 30 min. It is designed to support
incandescent, fluorescent and LED loads. It will power these loads at
cold starts for all normally off circuits or normally on circuits.
LESS AIR-CONDITIONING
Reduced costs for air-conditioning required to ensure the optimum
operating temperature when compared with equivalent systems
that dissipate much more heat. Higher reliability of fans and
electronic components.
MR16 LED EMERGENCY LIGHTING
Date:
Prepared by:
MR16 LED ILLUMINATION
With the remarkable technology development in the last
decade, the light-emitting diode (LED) is becoming the
preferred solution in low- and medium-power lighting
applications. The emergency lighting industry is no
exception: today virtually every new product introduced to
market includes “white” LEDs for emergency illumination.
• Self-testing/Self-diagnostic
• User programmable with password protection
• User programmable variable time delay
• Optional 100% normally Off output
• RS485 MODBUS RTU communication port
• Micro-processor controlled
Approvals
Project/Location:
Contractor:
Contractor:
Date:
Project/Location:
MR16 LED EMERGENCY LIGHTING
Prepared by:
510-LUMEN 6W MR16 LED
New in Fall 2013, we intoduce a 12V - 6W MR16 LED lamp,
which offer typical luminous flux of 510 lumens. Like the
lower wattage MR16 LED lamps, this new lamp is specially
designed for emergency lighting. It offers the same lighting
preformance as the 35W or 20W Mr16 IR. A twin emergency
head installed at a height of 7.5’ illuminates approximately
100’ path of egress.
Compared to halogen lamps (16-20W), these 4W MR16
LED lamps illuminate the same area of egress during an
emergency situation by using 75% less power. This has
a direct impact on the battery size, reducing the back-up
capacity needs by 75%. Consequently, it also reduces the
total cost of the application, with the use of smaller battery
capacity units, the possibility of using fewer fixtures due to
superior illumination, thus also reducing electrical wiring,
and it it reduces the environmental footprint.
MR16 LED ILLUMINATION
MR16 LED LAMP BENEFITS
With the remarkable technology development in the last
decade, the light-emitting diode (LED) is becoming the
preferred solution in low- and medium-power lighting
applications. The emergency lighting industry is no
exception: today virtually every new product introduced to
market includes “white” LEDs for emergency illumination.
• CSA C22.2 No. 141 certified.
• Energy-efficient LED MR16 lamp provides equivalent
lighting performance to a much higher watt halogen
MR16 lamp.
• Reduces required battery capacity by 75%, providing
necessary illumination with fewer remote heads and
battery units for project cost savings.
Extremely efficient and long-lasting, LED lamps become the
natural alternative to incandescent lamps due to three main
advantages:
• Small profile, compact white lighting is ideal for
architectural applications.
• = lamp efficacy: 50 - 70 lumen per watt compared to 15 30 lumen per watt of the best halogen lamp.
• Vibration-resistant LED stands up to industrial
environments.
• = operational life: 30,000+ hours, equivalent to a lifetime
warranty in emergency lighting.
• Ideal for indoor and outdoor use.
• = lower lamp temperature (80 - 120°C) is a huge benefit
for lighting in hazardous locations.
340-LUMEN 5W MR16 LED
200-LUMEN 4W MR16 LED
Keeping pace with technology, in 2012 we introduced a
12V-5W MR16 LED lamp. With a typical luminous flux of 340
lumens, this lamp has the same lighting performance as
a 20W high-output halogen MR16. A twin emergency head
installed at a height of 7.5ft illuminates more than a 70ft
path of egress.
Leading the technology trend, Emergi-Lite® offers a
complete series of 4W MR16 LED lamps available for all
the standard battery voltages: 6V, 12V, 24V and 120V. With
up to 30,000 hours of operational life and a luminous
flux of typically 200 lumens, they are available with most
emergency heads designed to hold an MR16 lamp and meet
the majority of illumination specifications. For example: one
pair of LED emergency heads installed at a height of 7.5ft,
illuminates a 6ft by 40ft path of egress.
510-LUMEN 6W MR16 LED
New in Fall 2013, we intoduce a 12V - 6W MR16 LED lamp,
which offer typical luminous flux of 510 lumens. Like the
lower wattage MR16 LED lamps, this new lamp is specially
designed for emergency lighting. It offers the same lighting
preformance as the 35W or 20W Mr16 IR. A twin emergency
head installed at a height of 7.5’ illuminates approximately
100’ path of egress.
Compared to halogen lamps (16-20W), these 4W MR16
LED lamps illuminate the same area of egress during an
emergency situation by using 75% less power. This has
a direct impact on the battery size, reducing the back-up
capacity needs by 75%. Consequently, it also reduces the
total cost of the application, with the use of smaller battery
capacity units, the possibility of using fewer fixtures due to
superior illumination, thus also reducing electrical wiring,
and it it reduces the environmental footprint.
MR16 LED LAMP BENEFITS
• CSA C22.2 No. 141 certified.
• Energy-efficient LED MR16 lamp provides equivalent
lighting performance to a much higher watt halogen
MR16 lamp.
• Reduces required battery capacity by 75%, providing
necessary illumination with fewer remote heads and
battery units for project cost savings.
Extremely efficient and long-lasting, LED lamps become the
natural alternative to incandescent lamps due to three main
advantages:
• Small profile, compact white lighting is ideal for
architectural applications.
• = lamp efficacy: 50 - 70 lumen per watt compared to 15 30 lumen per watt of the best halogen lamp.
• Vibration-resistant LED stands up to industrial
environments.
• = operational life: 30,000+ hours, equivalent to a lifetime
warranty in emergency lighting.
• Ideal for indoor and outdoor use.
• = lower lamp temperature (80 - 120°C) is a huge benefit
for lighting in hazardous locations.
340-LUMEN 5W MR16 LED
200-LUMEN 4W MR16 LED
Keeping pace with technology, in 2012 we introduced a
12V-5W MR16 LED lamp. With a typical luminous flux of 340
lumens, this lamp has the same lighting performance as
a 20W high-output halogen MR16. A twin emergency head
installed at a height of 7.5ft illuminates more than a 70ft
path of egress.
Leading the technology trend, Emergi-Lite® offers a
complete series of 4W MR16 LED lamps available for all
the standard battery voltages: 6V, 12V, 24V and 120V. With
up to 30,000 hours of operational life and a luminous
flux of typically 200 lumens, they are available with most
emergency heads designed to hold an MR16 lamp and meet
the majority of illumination specifications. For example: one
pair of LED emergency heads installed at a height of 7.5ft,
illuminates a 6ft by 40ft path of egress.
510-LUMEN 6W MR16 LED
New in Fall 2013, we intoduce a 12V - 6W MR16 LED lamp,
which offer typical luminous flux of 510 lumens. Like the
lower wattage MR16 LED lamps, this new lamp is specially
designed for emergency lighting. It offers the same lighting
preformance as the 35W or 20W Mr16 IR. A twin emergency
head installed at a height of 7.5’ illuminates approximately
100’ path of egress.
Compared to halogen lamps (16-20W), these 4W MR16
LED lamps illuminate the same area of egress during an
emergency situation by using 75% less power. This has
a direct impact on the battery size, reducing the back-up
capacity needs by 75%. Consequently, it also reduces the
total cost of the application, with the use of smaller battery
capacity units, the possibility of using fewer fixtures due to
superior illumination, thus also reducing electrical wiring,
and it it reduces the environmental footprint.
ORDERING INFORMATION(1)
SERIES
E= Series
SYSTEM VOLTAGE
KVA/KW
1= 120-120 input-output
2= 120/240-120/240
(3 wire in-out)
3= 277-277
4= 347-347
A= 3
B= 6
C= 9
D= 12
E= 15*
* Other voltages available using
external transformer (sold
separately)
* For 120 minutes
run time, minimum
120/240VAC in/out
RUN TIME
3= 30 minutes
6= 60 minutes
9= 90 minutes
12= 120 minutes
EXTERNAL CIRCUIT
BREAKER
B= no breakers
N####= normally on
F####= normally off
First two digits= Qty.
01 to 99 max (specify)
Last two digits= Amp rating
10, 15, 20, 25... (speficy)
Example :N1020 **
OPTIONS
A= fast recovery charge
B= remote meter panel
C= remote alarm panel
D= ethernet port
E= output trip alarm
F= NEXUS® system interface
G= “inverter on” dry contact
H= normally off full capacity output
I= extended battery warranty*
J= external maintenance bypass
K= seismic mounting bracket
L= drip shield
M= second output terminal block
N= normally on & normally off output**
40-FT. PATH OF EGRESS 2 X 4W MR16 LED
40-FT. PATH OF EGRESS 2 X 4W MR16 LED
70-FT. PATH OF EGRESS 2 X 5W MR16 LED
6
70-FT. PATH OF EGRESS 2 X 5W MR16 LED
40-FT. PATH OF EGRESS 2 X 4W MR16 LED
6
70-FT. PATH OF EGRESS 2 X 5W MR16 LED
40-FT. PATH OF EGRESS 2 X 4W MR16 LED
6
70-FT. PATH OF EGRESS 2 X 5W MR16 LED
6
* Consult your sales representative.
** Full capacity available on either output
EXAMPLE: E1A3N1020
IPS SINGLE
PHASE SERIES
IPS THREE
PHASE SERIES
SYSTEM
OPTIONS
USER INTERFACE
& DISPLAY
FUNCTIONS
CENTRAL SYSTEM
REQUEST DATA
FORM
UNITY SERIES
CH SERIES
P. 164-165
P. 166-167
P. 168-169
P. 170
P. 171
P. 172
P. 174-175
P. 176-178
161
161
Date:
Prepared by:
MR16 LED ILLUMINATION
With the remarkable technology development in the last
decade, the light-emitting diode (LED) is becoming the
preferred solution in low- and medium-power lighting
applications. The emergency lighting industry is no
exception: today virtually every new product introduced to
market includes “white” LEDs for emergency illumination.
WHAT IS EMEX?
160
Contractor:
Prepared by:
FEATURES
• PWM/Power Mosfet technology
- CSA C22.2 No. 141-10 – Emergency Lighting Equipment
- CSA C22.2 No. 107.3 – Uninterruptible Power Systems
- UL 1778 – Uninterruptible Power Systems
Applications
SERIES HIGHLIGHTS
MR16 LED EMERGENCY LIGHTING
Date:
Interruptible emergency lighting inverter system 3KVA –15KVA
The product is third generation inverter technology. LVD (Low Voltage
Disconnect) circuitry eliminates excessive battery drain after long
power outages.
Batteries
Automatic restart and recharge upon restoration of utility.
Each module has input and output protection and each module
measures and limits its own current.
Alarms and status indications are provided on the front panel display,
which provide clear and concise information, rather than a long list of
parameters, which may be confusing.
VERSATILE INSTALLATION
Modular design, easy front access freestanding cabinets,
fasten together when more than one cabinet is required.
Optional seismic kit available. All wiring provided is pre-cut
and terminated, along with the necessary hardware for proper
installation.
MONITORING AND CONTROL
User friendly programmable interface with LCD display provides
full metering values, easy program and control functions and a
wide range of visual and audible alarms.
IPS SINGLE PHASE SERIES
True Sine Waveform
Using a solid-state, pulse width modulation (PWM) inverter, the
systems produce pure sinusoidal output waveform with less than 5%
Total Harmonic Distortion (THD) for linear loads.
Reliability
The EMEX Power inverter and charger modules utilize solid state
electronics of the highest reliability to provide a rugged, easy to
maintain system with exceptional performance for emergency
lighting use. The system has been designed solely for emergency
lighting, and not modified from other less essential power supply
requirements. As such, the system has exceptional overload
performance without the need to over-specify the rating of the
inverter to ensure faults can be cleared.
LOW HEAT DISSIPATION
Very low heat loss in standby operating mode (see specifications
for exact values). Convection cooling in normal mode with forced
air during emergency and recharge mode. Battery cabinets:
convection cooling only.
THERMAL PERFORMANCE
Bonded oversized heat sinks for maximum thermal performance.
Cooling fans are energized only in inverter and recharge modes.
Project/Location:
Project/Location:
Project/Location:
Contractor:
Prepared by:
CHOOSING THE RIGHT SYSTEM
There are a variety of ways in which back-up
power can be provided. However, even though
certain methods are suitable for critical
applications, they may not necessarily be
suitable for Emergency Lighting.
162
163
Project/Location:
Contractor:
What is Emex?
Date:
A General Presentation about Emex Central Systems
Prepared by:
CHOOSING THE RIGHT SYSTEM
There are a variety of ways in which back-up
power can be provided. However, even though
certain methods are suitable for critical
applications, they may not necessarily be
suitable for Emergency Lighting.
This is because an Emergency Lighting system has unique load
characteristics. And since Emergency Lighting is a critical life-safety
installation, it is vital that a Central Battery System is designed with
these load characteristics in mind. EMEX Power central inverter
systems are specifically designed to provide emergency power for
emergency lighting systems in a power failure.
In choosing the right AC system to support
emergency lighting it is important to consider
the following questions:
General information on UPS systems:
Recharge period
UPS systems which are designed primarily for computer back-up
generally offer short run times, 5 or 10 minutes. The long run
times required for emergency lighting call for more powerful
chargers to recharge the larger bank of batteries needed in the
time prescribed by CSA.
Overload performance
An emergency lighting load will impose large “in-rush” currents
when starting lamps from cold. However, UPS systems are
often designed to shut down at only 125% overload and revert to
the incoming supply. During a total power failure situation, this
could result in total failure of the emergency lighting system.
Furthermore, a UPS may fail to clear a breaker on a lighting
circuit, meaning that a single short circuit fault could result in loss
of the entire emergency lighting supply.
Energy consumption and battery life
Most UPS systems operate in the “on-line” mode, whereby the
inverter runs constantly to supply the load, and power is taken
from the battery with the charger running constantly. This places
an excessive ripple on the battery (contrary to the advice given
by most battery manufacturers). Also, the system is constantly
generating heat which has a further detrimental effect on battery
life. There are energy costs and heat generation issues must be
addressed when running an on-line system.
Overload performance
Is the system able to start the full load without the mains supply
present. How does the system perform in a total power failure (ie
is the system able to start the load without the bypass supply being
available)?
Repeat duty
CSA141-10 requires a central battery system to fully recharge within
24 hours. Is the charger able to recharge the batteries quickly (80%
in 14 hours or 100% after 24 hours)?
Energy consumption and heat dissipation
Are the inverter and charger permanently running, shortening
the battery life, generating heat, wasting energy and shortening
component life? Are cooling fans running continuously, generating
noise?
Maintenance
Is the system easy to service and maintain? Is the system designed
in a modular format, or would the failure of even a minor component
require the whole system to be shut down and stripped for repair?.
164
Project/Location:
Contractor:
What is Emex?
Date:
Prepared by:
A General Presentation about Emex Central Systems
SYSTEM DESIGN
True Sine Waveform
Using a solid-state, pulse width modulation (PWM) inverter, the
systems produce pure sinusoidal output waveform with less than 5%
Total Harmonic Distortion (THD) for linear loads.
Reliability
The product is third generation inverter technology. LVD (Low Voltage
Disconnect) circuitry eliminates excessive battery drain after long
power outages.
Batteries
Automatic restart and recharge upon restoration of utility.
Approvals
- CSA C22.2 No. 141-10 – Emergency Lighting Equipment
- CSA C22.2 No. 107.3 – Uninterruptible Power Systems
- UL 1778 – Uninterruptible Power Systems
Applications
EMEX-Power Systems can be used in almost every type of
building, especially in architecturally sensitive applications or
when maintenance costs and testing of individual unit equipment
becomes significant. Our systems are designed to work with power
factor corrected as well as the most recent T5 and T5-HO electronic
ballasts.
The EMEX Power inverter and charger modules utilize solid state
electronics of the highest reliability to provide a rugged, easy to
maintain system with exceptional performance for emergency
lighting use. The system has been designed solely for emergency
lighting, and not modified from other less essential power supply
requirements. As such, the system has exceptional overload
performance without the need to over-specify the rating of the
inverter to ensure faults can be cleared.
Each module has input and output protection and each module
measures and limits its own current.
Alarms and status indications are provided on the front panel display,
which provide clear and concise information, rather than a long list of
parameters, which may be confusing.
SERIES HIGHLIGHTS
Performance
The EMEX-Power Systems work with lighting loads to provide
full light output for minimum 30 min. It is designed to support
incandescent, fluorescent and LED loads. It will power these loads at
cold starts for all normally off circuits or normally on circuits.
FEATURES
BENEFITS
COMPLIANCE WITH NFPA101
The self-testing meets the requirements of NFPA and UL. User
programmable time of testing. Test results, events or alarms
can be downloaded from history logs. Load monitoring. Reduced
testing/service time.
SELF-DIAGNOSTIC/SELF-TESTING
Programmable monthly and annual self-testing. Proven selfdiagnostic with information stored in separate memory logs for
Test, Event and Alarm. Microprocessor monitoring and control.
LOW HEAT DISSIPATION
Very low heat loss in standby operating mode (see specifications
for exact values). Convection cooling in normal mode with forced
air during emergency and recharge mode. Battery cabinets:
convection cooling only.
LESS AIR-CONDITIONING
Reduced costs for air-conditioning required to ensure the optimum
operating temperature when compared with equivalent systems
that dissipate much more heat. Higher reliability of fans and
electronic components.
VERSATILE INSTALLATION
Modular design, easy front access freestanding cabinets,
fasten together when more than one cabinet is required.
Optional seismic kit available. All wiring provided is pre-cut
and terminated, along with the necessary hardware for proper
installation.
EASY TO INSTALL
Quick installation and connection through flexible cable entries and
fast access terminal blocks. Low MTTR (<30 min.) due to modular
design, quick disconnect means and frontal access.
COMPLETE PROTECTION
Battery circuit breakers are standard. Modular standard systems
offer overload capacity, short-circuit protection, current- limiting,
low-battery disconnect and brownout protection as standard.
REDUCED DAMAGE RISKS
The full protection of the system will eliminate damage created by
external events and will increase lifetime of the electronics and the
batteries.
THERMAL PERFORMANCE
Bonded oversized heat sinks for maximum thermal performance.
Cooling fans are energized only in inverter and recharge modes.
INCREASED MTBF
Increased reliability and reduced preventative maintenance. No air
filters needed.
EASY MAINTENANCE
Diagnostics, troubleshooting, preventative maintenance and
service are made easier by using the front panel display or the
history logs.
MONITORING AND CONTROL
User friendly programmable interface with LCD display provides
full metering values, easy program and control functions and a
wide range of visual and audible alarms.
165
Project/Location:
Contractor:
IPS SINGLE PHASE SERIES
Date:
Prepared by:
Interruptible emergency lighting inverter system 3KVA –15KVA
FEATURES
• PWM/Power Mosfet technology
• Self-testing/Self-diagnostic
• User programmable with password protection
• User programmable variable time delay
• Optional 100% normally Off output
• RS485 MODBUS RTU communication port
• Micro-processor controlled
• 30, 60, 90, 120 minutes run times
• Summary alarm form C dry contact
• Generator compatibility
• Electronic and magnetic ballast compatible
• Automatic event, test and alarm log
• LCD display
• Maintenance free standard batteries
• Forced air cooling during emergency and recharge mode only
• Off when on standby
ELECTRICAL/MECHANICAL CHARACTERISTICS FOR 30 MINUTES BACK-UP TIME
POWER
RATING
KVA/KW
MAX. INPUT
CURRENT (A)(1)
HEAT LOSS IN
EFFIC.
NORMAL MODE
AT FULL
(BTU/HR)
LOAD % 120V 240V 277V 347V
BATT.
VDC
BATT.
ADC
NO. OF
BATT.(1)
IPS CABINET
DIMENSIONS
W”
H”
D”
NO. OF
BATT.
CAB.(1)(2)
BATT. CABINET
DIMENSIONS
W”
H”
D”
IPS
CABINET
WEIGHT
KG(1)
BATT.
TOTAL
BATTERY
CABINET
SYSTEM
WEIGHT
WEIGHT KG
WEIGHT
KG(1)
(EMPTY)(1)
KG(1)
3.0
98%
42
21
18
14
546
120
34
10
30
71
27
NA
NA
NA
NA
240
NA
105
345
6.0
98%
67
33
29
23
546
120
68
20
30
71
27
NA
NA
NA
NA
290
NA
210
500
9.0
98%
92
46
40
32
546
120
101
10
30
71
27
NA
NA
NA
NA
340
NA
372
712
12.0
98%
117
58
51
40
546
120
135
20
30
77
27
1
30
77
27
390
140
550
1080
15.0
98%
142
71
61
49
546
120
168
20
30
77
27
1
30
77
27
440
140
550
1130
1- For 30 min. discharge time. For other discharge times, consult factory.
2- Batteries are installed in the IPS cabinet for 3 to 9.0KVA systems, for 30 minutes only.
ORDERING INFORMATION(1)
SERIES
E= Series
SYSTEM VOLTAGE
KVA/KW
1= 120-120 input-output
2= 120/240-120/240
(3 wire in-out)
3= 277-277
4= 347-347
A= 3
B= 6
C= 9
D= 12
E= 15*
* Other voltages available using
external transformer (sold
separately)
* For 120 minutes
run time, minimum
120/240VAC in/out
RUN TIME
3= 30 minutes
6= 60 minutes
9= 90 minutes
12= 120 minutes
EXTERNAL CIRCUIT
BREAKER
B= no breakers
N####= normally on
F####= normally off
First two digits= Qty.
01 to 99 max (specify)
Last two digits= Amp rating
10, 15, 20, 25... (speficy)
Example :N1020 **
EXAMPLE: E1A3N1020
166
OPTIONS
A= fast recovery charge
B= remote meter panel
C= remote alarm panel
D= ethernet port
E= output trip alarm
F= NEXUS® system interface
G= “inverter on” dry contact
H= normally off full capacity output
I= extended battery warranty*
J= external maintenance bypass
K= seismic mounting bracket
L= drip shield
M= second output terminal block
N= normally on & normally off output**
* Consult your sales representative.
** Full capacity available on either output
Project/Location:
Contractor:
IPS SINGLE PHASE SERIES
Date:
Prepared by:
Interruptible emergency lighting inverter system 3KVA –15KVA
SYSTEM SPECIFICATIONS
CABINETS
Modular design, freestanding NEMA type 1 steel cabinets powder
coated for corrosion and scratch resistance. Front access design
through hinged lockable doors requires only 42” front, 2” back and
side clearance and 12” top clearance without drip shield. Top conduit
entry Gland Plate.
GENERAL
DESIGN
Stand-by. PWM inverter type utilizing Power
Mosfet technology with 500ms transfer time.
CONTROL
Microprocessor controlled, 4 x 20-character
display with touch pad controls & functions
METERING
Input & Output Voltage, Battery Voltage,
Battery & Output Current, Output VA,
Temperature
COMMUNICATIONS
INVERTER
Using Power Mosfet/PWM technology the inverter converts
DC voltage supplied by the batteries to AC voltage of a precise
stabilized amplitude and frequency, suitable for most sophisticated
electrical equipment. True sinusoidal output waveform with very low
distortion (less than 5% for linear loads). Overload capability of 120%
continuous, 150% for 1 minute and 200% for 10 seconds.
RS-485 MODBUS RTU Port (DB-9)
ELECTRICAL INPUT
VOLTAGE
INPUT FREQUENCY
120, 277, 347VAC 2-wire or 120/240VAC
3-wire, 1-phase, +10%/ -15%
CHARGER
Fully automatic, temperature compensated, charger recharges
fully discharged batteries in maximum 24 hours at nominal AC
input voltage. AC input current limiting and over-voltage protection
included.
60Hz
ELECTRICAL OUTPUT
VOLTAGE
120, 277, 347VAC 2-wire or 120/240 3-wire,
1-phase
DYNAMIC VOLTAGE
+/-2% for +/-25% load step change, +/-3%
for a 50% load step change, recovery within
3 cycles
BATTERY
OUTPUT FREQUENCY
60Hz +/- 2Hz during emergency mode
System is provided standard with 10 year, maintenance free,
sealed valve regulated, lead calcium batteries. 30, 60, 90 & 120
min. standard discharge time at full load under normal operating
temperature (20ºC to 25ºC). Low Voltage Disconnect protection
included. No special ventilation required.
LOAD POWER FACTOR
0.7 lag to 0.9 lead
SUPERVISION
INVERTER OVERLOAD
120% continious, 150% for 1 minute and 200%
for 10 seconds
PROTECTION
Optional External Distribution Circuit Breaker
Automatic self tests consist of a 2-minute monthly, 1/3 discharge at 6
months and full annual discharge. The front-mounted control panel
includes, a 4-line 20-character LCD display with a keypad to control
and monitor the operation of the system. This allows the operator to
easily “watch” system functions as they occur and check on virtually
any aspect of the system’s operation. Standard RS485 MODBUS RTU
diagnostic interface.
HARMONIC DISTORTION
CREST FACTOR
<5% THD for linear load
3
ENVIRONMENTAL CONDITIONS
STORAGE/TRANSPORT
OPERATING
TEMPERATURE
ALTITUDE
RELATIVE HUMIDITY
AUDIBLE NOISE
32ºF to 104ºF (0ºC to 40ºC) without batteries
68ºF to 86ºF (20ºC to 30ºC) with batteries(1)
ALARMS
System operates safely from 32°F to 104°F
(0°C to 40°C) but optimum operation is
between 68° F and 77°F (20°C to 25°C).
Battery performance can be affected by
temperature.
Battery High/Low, Low Voltage Disconnect, Battery Disconnect,
Maintained Lamp Off, Charger Fail, Supply From Battery, System
Inhibit, Circuit Breaker Trip, Module Breaker Trip, Inverter
Undervoltage, Inverter Overvoltage, Output Overcurrent, Hi Temp,
Over Temp, Unit in Bypass, Inverter Frequency Control Failed,
Processor Reset.
<10,000 feet (above sea level) without
de-rating
0 to 95% non-condensing
OPTIONAL FEATURES
45 dBA at 1m from surface in emergency
mode
External Output Circuit Breakers, Output Trip Alarms, Extended
Battery Warranty, 12 Hours Fast Recharge, External Maintenance
Bypass Switch, Remote Meter Panel, Ethernet Port, Nexus® System
Interface. Dripshield, Remote Alarm Panel, Normally Off Output,
Seismic Mounting Brackets, Dry Contact Relay.
(1) - max. 3 months at 77°F-86°F (25°C-30°C)
SINGLE LINE DIAGRAM
FACTORY START-UP
Includes one additional year of warranty. See warranty conditions.
WARRANTY
(full limited warranty conditions available upon request)
Limited manufacturer warranty is one-year, parts and labor, for
system electronics. Battery warranty is one year full plus 9 years
pro-rata for a total of 10 years, under normal operating conditions.
System must be put in service within 6 months from ship date in
order to validate warranty. Consult factory for other battery types.
167
Project/Location:
Contractor:
IPS THREE PHASE SERIES
Date:
Prepared by:
Interruptible emergency lighting inverter system 4.5KVA –54KVA
FEATURES
• PWM/Power Mosfet technology
• Self-testing/Self-diagnostic
• User programmable with password protection
• User programmable variable time delay
• Optional 100% normally Off output
• RS485 MODBUS RTU communication port
• Micro-processor controlled
• 30, 60, 90, 120 minutes run times
• Summary alarm form C dry contact
• Generator compatibility
• Electronic and magnetic ballast compatible
• Automatic event, test and alarm log
• LCD display
• Maintenance free standard batteries
• Forced air cooling during emergency and recharge modes only
• Off when on standby
ELECTRICAL/MECHANICAL CHARACTERISTICS FOR 30 MINUTES BACK-UP TIME
BATT.
BATT.
TOTAL
HEAT
NO. IPS CABINET NO.
MAX. INPUT
TOTAL
CABINET
CABINET TOTAL IPS
BATT.
POWER EFFIC. CURRENT (A)(1) LOSS IN
BATTERY
NO. OF
NO. OF OF DIMENSIONS OF 20
SYSTEM
BATT. BATT.
CABINET CABINET
DIMENSIONS
DIMENSIONS
RATING AT FULL
WEIGHT
NORMAL
30 BATT.
BATT.
BATT. IPS
WEIGHT
VDC
ADC
WEIGHT WEIGHT KG
(1)
For %all208/
fluorescent/incandescent/LED
loads
KVA/KW LOAD
KG(1)
MODE
CAB.
CAB.(1)(2)
CAB.
480/ 600/
KG(1)
KG(1)(2)
(1)(2)
(1)(2)
W” H” D”
W” H” D”
W” H” D”
(BTU/HR)
120V 277V 347V
(EMPTY)(1)
4.5
98%
29 13
10
546
120
50
20
1
30 71 27
NA
NA NA NA
NA
NA NA NA
265
NA
210
9.0
98%
42 18
14
546
120
101
10
1
30 71 27
NA
NA NA NA
NA
NA NA NA
340
NA
372
475
712
13.5
98%
54 23
19
546
120
151
20
1
30 77 27
1
30 77 27
NA
NA NA NA
415
140
550
1105
18.0
98%
67 29
23
546
120
202
20
1
30 77 27
1
30 77 27
NA
NA NA NA
540
140
744
1424
22.5
98%
79 34
27
546
120
252
30
1
30 77 27
NA
NA NA NA
1
30 71 30
615
165
825
1605
27.0
98%
92 40
32
546
120
303
30
1
30 77 27
NA
NA NA NA
1
30 77 30
690
165
1116
1971
31.5
98%
104 45
36
1092
120
353
30
2
30 77 27
1
30 77 27
NA
NA NA NA
905
140
1116
2161
36.0
98%
117 51
40
1092
120
403
40
2
30 77 27
NA
NA NA NA
1
30 77 30
1030
165
1488
2683
40.5
98%
129 56
45
1092
120
454
40
2
30 77 27
2
30 77 27
NA
NA NA NA
1105
280
1488
2873
45.0
98%
142 61
49
1092
120
504
50
2
30 77 27
1
30 77 27
1
30 77 30
1180
305
1860
3345
49.5
98%
NA 67
53
1092
120
555
50
2
30 77 27
1
30 77 27
1
30 77 30
1255
305
1860
3420
54.0
98%
NA 73
58
1092
120
605
60
2
30 77 27
NA
NA NA NA
2
30 77 30
1380
330
2232
3942
1- For 30 min. discharge time. For other discharge times, consult factory.
2- Batteries are installed in the IPS cabinet for 4.5 to 9.0KVA systems, for 30 minutes only.
ORDERING INFORMATION(1)
SERIES
EIII=
Series
SYSTEM VOLTAGE
1= 120/208 4 wire in-out
2= 277/480
3= 347/600
* Other voltages available using
an external transformer (sold
separately)
KVA/KW
A= 4.5
B= 9
C= 13.5
D= 18
E= 22.5
F= 27
G= 31.5
H= 36
I=40.5
J= 45**
K= 49.5*
L= 54*
RUN TIME
3= 30 minutes
6= 60 minutes
9= 90 minutes
20
12= 1
minutes
* Min. 277/480VAC in/out
EXTERNAL CIRCUIT BREAKER
B= no breakers
N####= normally on
F####= normally off
First two digits= Qty.
01 to 99 max (specify)
Last two digits= Amp rating
10, 15, 20, 25... (specify)
Example: N1020
** For 120/208VAC in/out,120
mins. runtime not available.
OPTIONS
A= fast recovery charge
B= remote meter panel
C= remote alarm panel
D= ethernet port
E= output trip alarm
F= NEXUS® system interface
G= “inverter on” dry contact
H= normally off full capacity output
I= extended battery warranty*
J= external maintenance by pass
K= seismic mounting bracket
L= drip shield
M= second output terminal block
N= normally on & normally off output**
* Consult your sales representative.
** Full capacity available on either output
EXAMPLE: EIII1A3N1020
168
Project/Location:
Contractor:
IPS THREE PHASE SERIES
Date:
Prepared by:
Interruptible emergency lighting inverter system 4.5KVA –54KVA
SYSTEM SPECIFICATIONS
GENERAL
DESIGN
Stand-by. PWM inverter type utilizing Power
Mosfet technology with 500ms transfer time.
CONTROL
Microprocessor controlled, 4 x 20-character
display with touch pad controls & functions
METERING
Input & Output Voltage, Battery Voltage, Battery
& Output Current, Output VA, Temperature
COMMUNICATIONS
RS-485 MODBUS RTU Port (DB-9)
ELECTRICAL INPUT
VOLTAGE
INPUT FREQUENCY
120/208, 277/480, 347/600VAC 3-phase 4-wire
+10% / -15%.
60Hz
ELECTRICAL OUTPUT
VOLTAGE
120/208, 277/480, 347/600VAC 3-phase 4-wire.
DYNAMIC VOLTAGE
+/-2% for +/-25% load step change, +/-3% for a
50% load step change, recovery within 3 cycles
HARMONIC
DISTORTION
<5% THD for linear load
OUTPUT FREQUENCY
60Hz +/- 2Hz during emergency mode
LOAD POWER FACTOR
0.7 lag to 0.9 lead
INVERTER OVERLOAD
120% continuous, 150% for 1 minute and 200%
for 10 seconds
PROTECTION
Optional External Distribution Circuit Breaker
CREST FACTOR
3
ENVIRONMENTAL CONDITIONS
STORAGE/TRANSPORT
32ºF to 104ºF (0ºC to 40ºC) without batteries
68ºF to 86ºF (20ºC to 30ºC) with batteries(1)
OPERATING
TEMPERATURE
System operates safely from 32°F to 104°F (0°C
to 40°C) but optimum operation is between 68°
F and 77°F (20°C to 25°C). Battery performance
can be affected by temperature.
ALTITUDE
<10,000 feet (above sea level) without de-rating
RELATIVE HUMIDITY
AUDIBLE NOISE
0 to 95% non-condensing
45 dBA at 1m from surface in emergency mode
(1) - max. 3 months at 77°F-86°F (25°C-30°C)
SINGLE LINE DIAGRAM
CABINETS
Modular design, freestanding NEMA type 1 steel cabinets powder
coated for corrosion and scratch resistance. Front access design
through hinged lockable doors requires only 42” front, 2” back and
side clearance and 12” top clearance without drip shield. Top conduit
entry Gland Plate.
INVERTER
Using Power Mosfet/PWM technology the inverter converts
DC voltage supplied by the batteries to AC voltage of a precise
stabilized amplitude and frequency, suitable for most sophisticated
electrical equipment. True sinusoidal output waveform with very low
distortion (less than 5% for linear loads). Overload capability of 120%
continuous, 150% for 1 minute and 200% for 10 seconds.
CHARGER
Fully automatic, temperature compensated, charger recharges
fully discharged batteries in maximum 24 hours at nominal AC
input voltage. AC input current limiting and over-voltage protection
included.
BATTERY
System is provided standard with 10 year, maintenance free,
sealed valve regulated, lead calcium batteries. 30, 60, 90 & 120
min. standard discharge time at full load under normal operating
temperature (20ºC to 25ºC). Low Voltage Disconnect protection
included. No special ventilation required.
SUPERVISION
Automatic self tests consist of a 2-minute monthly, 1/3 discharge at
6 months and full annual discharge.The front-mounted control panel
includes, a 4-line 20-character LCD display with keypad to control
and monitor the operation of the system. This allows the operator to
easily “watch” system functions as they occur and check on virtually
any aspect of the system’s operation. Standard RS485 MODBUS RTU
diagnostic interface.
ALARMS
Battery High/Low, Low Voltage Disconnect, Battery Disconnect,
Maintained Lamp Off, Charger Fail, Supply From Battery, System
Inhibit, Circuit Breaker Trip, Module Breaker Trip, Inverter
Undervoltage, Inverter Overvoltage, Output Overcurrent, Hi Temp,
Over Temp, Unit in Bypass, Inverter Frequency Control Failed,
Processor Reset.
OPTIONAL FEATURES
External Output Circuit Breakers, Output Trip Alarms, Extended
Battery Warranty, 12 Hours Fast Recharge, External Maintenance
Bypass Switch, Remote Meter Panel, Ethernet Port, NEXUS® System
Interface. Dripshield, Remote Alarm Panel, Normally Off Output,
Seismic Mounting Brackets, Dry Contact Relay.
FACTORY START-UP
Includes one additional year of warranty. See warranty conditions.
WARRANTY
(full limited warranty conditions available upon request)
Limited manufacturer warranty is one-year, parts and labor, for
system electronics. Battery warranty is one year full plus 9 years
pro-rata for a total of 10 years, under normal operating conditions.
System must be put in service within 6 months from ship date in
order to validate warranty. Consult factory for other battery types.
169
Project/Location:
Contractor:
Systems Options
Date:
Details
Prepared by:
(-A) 12 HOUR FAST RECHARGE
(-H) NORMALLY OFF OUTPUT
Battery charger upgrade option which decreases the time required
to recharge a fully discharged battery to a fully charged state. The
normal 24 hour recharge time is reduced to a 12 hour period.
This output circuit is dedicated for the emergency only equipment.
Emergency only equipment operates during power outages and when
the system is on battery back up. This option leaves the normally off
load circuits off during normal utility power conditions.
(-B) REMOTE METER PANEL
(-I) EXTENDED BATTERY WARRANTY
The panel allows monitoring of parameters and control from remote
locations up to 200 feet away from the inverter system. Also, the
remote panel provides a complete touch pad interface allowing the
user to monitor, control and program the inverter system.
Extends battery warranty from 10 years pro-rated to 20 years
pro-rated.
(-J) EXTERNAL MAINTENANCE BYPASS
SWITCH
(-C) REMOTE SUMMARY ALARM PANEL
Wall mountable box provides visual and audible alarms with silence
switch. The panel consists of LED indicators and built in audible
alarm and may be located up to 1,000 feet away from the inverter
system.
The external maintenance bypass switch is mounted in a maximum
of 42”H x 36”W x 12”D NEMA 1 separate enclosure, used to
completely isolate the inverter system from the connected load and
AC utility input. This option allows the system to be safely powered
down for maintenance or service.
(-D) ETHERNET PORT
(-K) SEISMIC MOUNTING KIT
Interface to ethernet network. Provides status information and allows
system management via internet browser.
The seismic mounting kit option is designed to prevent system
movement during seismic events. Heavy duty brackets are provided
to secure system cabinetry to your surfaces.
(-E) OUTPUT TRIP ALARM
System triggers an alarm when any output breaker trips.
(-L) DRIP SHIELD
(-F) NEXUS® SYSTEM INTERFACE
Hood cover to protect the enclosure against falling water from
sprinkler systems.
Allows remote monitoring of the system from a server (wireless or
cabled communication).
(-M) SECOND OUTPUT TERMINAL BLOCK
(-G) INVERTER ON DRY CONTACTS
The output of the Central System is divided into two. The load can be
connected to either outputs.
Form C dry contacts that will change state when the system transfers
to battery.
(-N) NORMALLY ON & NORMALLY OFF
OUTPUTS
The Central System can have both normally on and normally off
outputs. Either output can handle 100% of the load.
170
Project/Location:
User Interface &
Display Functions
Contractor:
Date:
Prepared by:
METER & READING FUNCTIONS MENU
SERVICE MENU FUNCTIONS
• AC Voltage Output
• AC Current Ouput Normally On
• AC Current Output Normally Off
• Battery Voltage
• Battery Charging Current
• Battery Discharging Current
• KVA Total Output
• Cabinet Internal Temperature
• Inverter Frequency
• Real Time Clock
• Time Delay
• Monthly Test Result
• Half Year Test Result
• Annual Test Result
• Passkeyword protected
• Set Battery Voltage & Current
Ranges
• Set System Voltage & Current
Ranges
• Set System Phase
• Set Normally OFF Load
• Set Language
• Set Real Time Clock & Calendar
• Set Time Delay Function
• Set Manual Test Duration
• Set Self Test Sequence
• Set Buzzer Function
• Event Log Reading
ADMINISTRATION MENU
FUNCTIONS
ALARM AND EVENTS
• Event Logging (1000) Type Date &
Hour
• Transfer Mode
• Standby
• Load Off
• Stop Mode
• Lock-Out Mode
• Forced Transfer
• Battery Volt
• Battery Disconnect
• Mains Out Of Range
• Manual Test
• Monthly Test
• Half Year Test
• Yearly Test
• Modbus Transfer
• Passkeyword protected
• Read/Set Serial Number
• Read/Set Manufacturing Date
• Read/Set Installation Date
• Read Firmware Version
• Read/Clear Battery Elapse Time
• Read/Clear Total Power Failures
• Read/Clear Total Alarms
• Clear Event Log
• Enter Calibration Routine
SYSTEM TESTING
EMEX Central Battery Systems provide manual and automatic test functions. Manual test can be activated any time using the test key
provided on the control panel. Manual testing will do a programmable fixed test time and can be aborted any time by pushing again on
the test key. Automatic test and diagnostic is done following an annual sequence. Every month a quick diagnostic test of 2 minutes is
performed. At the 6 month mark, a 1/3 timed discharge test is done, and at the 12 month, a full discharge, down to LVD is performed.
Pass/Fail and discharge time are registered in the event log. Test time and date is programmed using the Service Menu.
171
Project/Location:
Contractor:
Date:
Central System Request Data
Prepared by:
1) INPUT VOLTAGE
Single phase
(2 wire + ground)
120VAC
Single phase
(3 wire + ground)
120/240VAC
Three phase
(4 wire + ground, Y)
Three phase
(3 wire + ground, Δ)
208VAC
277VAC
120/208VAC
277/480VAC
347/600VAC
208VAC
480VAC
600VAC
277VAC
347VAC
2) OUTPUT VOLTAGE
Single phase
(2 wire + ground)
120VAC
208VAC
Single phase
(3 wire + ground)
120/240VAC
120/277VAC
Three phase
(4 wire + ground, Y)
120/208VAC
277/480VAC
347VAC
347/600VAC
3) SYSTEM CAPACITY
KVA rating:
a) Please consider total power consumption of the complete fixture, not just the lamp wattage
b) Even if the systems can run with 100% load, it is recommended as standard practice to use a system with a capacity at least 20% over
maximum connected load
4) RUNTIME
30 minutes
60 minutes
90 minutes
Fluorescent
L.E.D.
120 minutes
Other
5) TYPE OF LOADS
Incandescent
Others
6) MODE OF OPERATION
Normally ON (24/7)
Normally OFF (emergency only)
7) OUTPUT CIRCUIT BREAKERS
# of CB
Amps
# of poles
Normally “On”
Normally “Off”
Trip alarm
# of CB
Amps
# of poles
Normally “On”
Normally “Off”
Trip alarm
8) OPTIONS (REFER TO AVAILABLE OPTIONS FOR EACH SYSTEM TYPE)
(-A) 12 Hour Fast Recharge
(-H) Normally Off Output
(-B) Remote Meter Panel
(-I) Extended Battery Warranty
(-C) Remote Summary Alarm Panel
(-J) External Maintenance Bypass Switch
(-D) Ethernet Port
(-K) Seismic Mounting Kit
(-E) Output Trip Alarm
(-L) Drip Shield
(-F) NEXUS System Interface
(-M) Second Output Terminal Block
(-G) Inverter On Dry Contacts
(-N) Normally On & Normally Off outputs
®
172
Project/Location:
Unity Series
120VDC Central Single Source
Emergency Lighting System
Contractor:
Date:
Prepared by:
STANDARD FEATURES AND CONTROLS
Time and labour saver only one conduit
required!
• LVD at 91% of nominal
In an existing or new installation where exit signs and emergency
lighting may be supplied by a single 120VDC source using a common
negative wire, one normally on positive and one normaly off positive.
3 wire output from the system reduces the number of conductors by
up to 40%. It also eliminates 50% of the conduit, EMT or BX runs by
using a single common conduit for LED exits and emergency lighting
remotes.
• Temperature Compensation
FEATURES
• Charger Failure Alarm
• Reduced number of conductors
• High Battery Voltage Alarm
•Eliminates 50% of conduit, BX or EMT runs for exit and
emergency lighting
• Test Switch
• Remote Monitor Alarm Panel
• Control and supervision functions on single modular board
• Brownout Protection
•Complete package of full supervisory functions and alarms
included in standard unit
• Dry Contacts
• Ground Fault Alarm (Audible & Visual)
• DC Volt & Ammeter (2% Accuracy)
• AC present LED indicator
• Float level Charge LED indicator
• Equalize level Charge LED indicator
• AC Failure Alarm
• Single-source 120VDC supply for both exit and emergency lights
• Floor-mount cabinet
•BMEC - Ontario Building Materials Evaluation Commission
Approved
• Battery is sealed maintenance free lead calcium
• SPF - sprinkler-proof cabinet comes with drip shield
•All Unity Series systems are designed and manufactured in
Canada
OPTIONAL FEATURES CODE
• CSA and Ontario Hydro approved
•BMEC (Building Materials Evaluation Commission) approved for
compliance to the Ontario Building Code
• Overall reduction on power consumption using LED Exit Signs
OPERATIONS
Unity Series Central Emergency Lighting Systems are available in
free-standing cabinet style enclosures
• Time Delay TD
• 3 Phase Sensing 3PH
• 12 Hour Recharge 12HR
• Battery exerciser
CYC
• Input battery circuit breaker BCB
• Common Zone sensing ZSC
APPLICATION
• Heavy duty, sheet-steel cabinet
New construction or retro-fit, the Unity Series utilizes the latest
technology and engineering to reduce the cost of emergency lighting
installations. The unique 3 wire design allows for the use of just one
conduit. With one positive dc normally energized conductor and a
common negative conductor the LED exits are supplied constant
power. With the same common negative conductor and another
positive DC conductor the remote emergency lights are powered on
demand. Available in sizes from 4120W to 22520W for 30 minutes.
Other runtimes available. Please consult factory.
•Cabinets are painted ASA No. 61 grey electrolyte resistant enamel
• Locking and hinged front door
•Front access to battery charger for ease of inspection and
servicing
CHARGER CONTROLS
Emergi-lite®’s solid state fully automatic charger features single
module control board design. This feature provides cost effective
superior performing equipment, with ease of maintenance and
service ability.
ELECTRICAL
Input: 120V, 208V, 240V, 277V, 347V, 600VAC 60HZ Single Phase
Output: 120VDC 3 wire (normally on positive, common negative and
normally off positive).
Systems have been designed for minimum 1/2 hour operation time
and are capable of full recharge in 24 hours. For systems rating chart
and ordering guide please see next page. Other discharge times are
available upon request.
174
Project/Location:
Contractor:
Unity Series
Date:
120VDC Central Single Source
Emergency Lighting System
Prepared by:
TYPICAL INTERCONNECTION WIRING
DIAGRAM
WARRANTY
The complete system is guaranteed for a period of one (1) year
against defects in workmanship and materials. The battery portion
of the equipment carries a ten (10) year pro-rata warranty during its
useful service life against defects in workmanship and materials.
The battery warranty is subject to the provision of normal testing
and inspection as specified in the Canadian Electrical Code, Section
46-102, and National Fire Code of Canada. Limit room ambient
temperature between 20°C to 25°C (68°F to 77°F). Optimum system
performance occurs at 25°C (77°F). A battery service life is defined
as the period which the battery could still provide at least 80% of its
rated capacity.
EXIT
BATTERY BACKUP
CONDUIT
CONDUIT
APPROVALS
• CSA Certified
SINGLE SUPPLY UNIT UNIQUE
• Ontario Hydro: Rule 46-108 (3)
NORMAL EMERGENCY POWER SUPPLY
UNIT WITH EXIT SIGN AND REMOTE HEADS
ENCLOSURE DIMENSIONS
SYSTEM SERIES
HXWXD
UNI 4120
38” (96.5 cm) x 38” (96.5 cm) x 18” (45.7 cm)
UNI 5660-11260
38” (96.5 cm) x 38” (96.5 cm) x 28” (71.1 cm)
UNI 13140-22520
56” (142.2 cm) x 38” (96.5 cm) x 28” (71.1 cm)
CONDUIT
CAD Drawing illustrates how the Unity Series is applied,
saving time, material and money. Call your local
Emergi-Lite® Representative for further information, or application assistance.
UNIT RATING
SL Series batteries: maintenance free, sealed Lead-Calcium. Watts
at 91% of nominal voltage.
CAPACITY IN WATTS
30 MIN
1H00
1H30
2H00
UNI 4120
4 120
2 450
1 790
1 440
UNI 5660
5 660
4 015
2 935
2 355
UNI 9390
9 390
5 590
4 080
3 290
UNI 11260
11 260
6 700
4 890
3 940
UNI 13140
13 140
7 820
5 710
4 600
UNI 18780
18 780
11 180
8 160
6 580
UNI 22520
22 520
13 400
9 780
7 880
ORDERING INFORMATION
SYSTEM
DESIGNATION
UNI
A.C. INPUT
VOLTAGE
(1PH)
120= 120VAC
208= 208VAC
240= 240VAC
277= 277VAC
347= 347VAC
600= 600VAC
BATTERY TYPE
SG = sealed
Lead Calcium
CAPACITY
IN WATTS
__________*
QTY OF EXIT
SIGNS
50E= 50 Exit
Signs
100E= 100 Exit
Signs
MOUNTING
D.C.
OUTPUT
VOLTAGE
C= Console
120= 120VDC
OPERATING
TIME
30= 30 minutes
60= 60 minutes
90= 90 minutes
120= 120
minutes
For other
discharge times,
please consult
your sales
representative.
*Select from
Battery Capacity
chart in folder
175
OPTIONS
TD= Time delay
(15 minutes)*
3PH= 3 phase
sensing
12HR= 12 hour
recharge
CYC= Battery
exerciser
BCB= Battery
circuit
breaker
ZSC= Common
zone
sensing**
* Specify time.
** Specify No. of zones.
Project/Location:
Contractor:
CH Series
DC Central Emergency Lighting System
Date:
Prepared by:
CHARGING OPERATION
Fully automatic charger, battery and
specified transfer and distribution features
The charger will fully recharge the battery within a twenty four hour
period from a full discharge. The charger maintains regulation of
± 0.5% of voltage for a ± 10% input voltage variation. The charger
provides automatic equalize cycle whenever the charge current
is more than a preset value. The charger operates in an equalize
mode after each utility power return. This ensures maximum battery
capacity at all times, with maintained life expectancy
Emergi-Lite®’s DC Systems are utilized where a large number
of remote heads or standard 120V incandescent fixtures may be
supplied from a single source. The systems offer the advantage of a
central location for maintenance with full supervision of all operating
functions. Contact your Emergi-Lite® representative for information.
FEATURES
STANDARD CONTROLS
• 24, 36 and 120 VDC systems sealed lead acid batteries
The front panel includes the following controls:
• Control and supervision functions on single modular board
• DC Battery Voltmeter (2% Accuracy)
•Complete package of full supervisory functions and alarms
included in standard system
• DC Charge Rate Ammeter (2% Accuracy)
• Green “ac on” LED (on at all times except during power failure)
• Totally sealed maintenance free Lead Calcium batteries
•Green “float” LED (indicates that the battery is receiving float
charge to maintain the battery at full charge at all times)
• All systems are designed and manufactured in Canada
• CSA certified
•Amber “equalize” LED (indicates that the charger is in the high
charge equalize mode, balancing the charge level in the individual
battery cells)
• B
MEC (Building Materials Evaluation Commission) approved for
compliance to the Ontario Building Code
• Brown-out protection
BATTERY
• Test switch
Sealed Maintenance-Free Lead Calcium Gas Recombination
(SL Series)
Uses gas recombination to eliminate the escape of hydrogen. Thick
plates are constructed of high strength material which resists
shedding, flaking, or mechanical failure. Design Life: 10 years under
normal operating conditions.
• A.C input circuit breaker
STANDARD ALARMS
• AC Failure LED and Alarm
• High Battery Voltage LED and Alarm
• Charger Failure LED and Alarm
CHARGER FEATURES
• Ground Leakage Alarm
Emergi-Lite® has developed a unique modular charger design in
which all electronic control functions and pilot lights are mounted
on a single control board. This is connected to the operating power
components using screw type connectors– making the circuit board
easily removable by means of only four screws. Any required field
service, consequently, is faster and significantly simpler than with
older style multiple board designs. All chargers include a contactor
which automatically disconnects the batteries from the load when
battery bank voltage falls below 91% of nominal, in order to prevent
over-discharge of batteries. The operating temperature for the
system is from 20ºC to 25ºC (68ºF to 77ºF). The control board is
temperature compensated in order to meet the battery required float
voltage at temperatures below and above 25°C, as recommended by
battery manufacturers. Internal control allows for spark free battery
bank connection during installation and scheduled maintenance
procedures.
•An audible alarm and a common LED shall indicate “Ground
Leakage” and/or Fuse/Circuit Breaker open/trip alarm
• High ambient temperature
DISTRIBUTION OPTIONS
A separate distribution panel is available for all systems. A choice
of fuses or circuit breakers is available. Fuse Distribution Panel
Select -OPF ( ) for separate distribution fuse panel. Select -OFA ( )
for separate distribution fuse panel with visual and audible alarm on
main console for failure of any fuse.
Note: “( )” indicates the number of circuits required.
Circuit Breaker Distribution Panel Specify - CBO ( ) for separate
circuit breaker panel. Specify - OCA ( ) for separate circuit breaker
panel with visual and audible alarm on main console for tripping or
opening of any breaker.
176
Project/Location:
Contractor:
CH Series
Date:
Prepared by:
DC Central Emergency Lighting System
TRANSFER OPTIONS
TYPICAL SPECIFICATION
• System may be selected to either turn on a normally “off” load or
alternatively on 120VDC systems, maintain a normally “on” load
• Normally “off” (DC load): (CP)
• If the lamp load is going to be turned on in the event of power
failure add suffix –CP to the model number
• Normally “on” (AC/DC load): (TS) 120 V DC systems only
• The 120V incandescent load shall have 120VAC power normally
supplied to it and the load shall be transferred to 120VDC upon
failure. Add suffix –TS to the model number. For other AC input
voltages please contact factory
• Both Normally “on” & “off” loads: (CP/TS)
• Both of the above apply
Provide and install a complete emergency lighting system as
described herein and shown on the drawings. The system shall
consist of a charger, battery and specified transfer and distribution
features. The charger shall be fully automatic solid state type using
integrated circuit control. The output voltage variation shall be ±
0.5% for input variation of ± 10%. The charger shall recharge the
battery within 24 hours after a power failure. The charger shall
include a contactor to automatically disconnect the battery from
the load when the battery voltage falls below 91% of nominal.
The charger shall be of a modular design with all pilot lights and
electronic control functions on a single board mounted behind the
front panel. The single control board shall have LED pilot lights for
the following functions (which shall show through the front panel):
OTHER OPTIONS
• Green “float” Charge LED
• Green “ac on” LED
• Amber “equalize” LED
CODE
DESCRIPTION
Time delay TD
3 phase sensing 3PH
Battery circuit breaker BCB
Battery exerciser
CYC
Common Zone Sensing ZSC( )*
Individual zone sensing, specify number of zones ZSI( )*
•The single control board shall also include LED and an audible
alarm with call-back function for the following alarms:
• AC Failure
• High Battery Voltage
• Charger Failure
• Battery Ground Leakage
• High ambient temperature
* Zone explanation: each specified zone relay monitors an individual lighting circuit in a
building. Should the monitored circuits lose AC power, the connected lighting load will
automatically illuminate:
OPTIONAL ALARMS
a - all zones if ZSC is specified
b - that zone only if ZSI is specified
• Fuse/Circuit Breaker Open/Trip
CABINETS
SELECT SL BATTERY
Systems are available in a free standing floor mount cabinet. The
cabinet shall be constructed of not less than 14 gauge steel with
corrosion resistant undercoating. Standard finish is ASA61 grey
baked enamel.
Select battery bank voltage, capacity and duration of required backup
time. Select AC input voltage. Select system transfer option from CP
(), TS( ), or CP( )/TS( ) where the load watts are shown in brackets.
SELECT OPTIONS
WARRANTY
The equipment shall be provided with a separate distribution panel
with _____ fuses or circuit breakers (select one) rated at ______
Amps.
Optional: All distribution fuse or circuit breaker panels shall
be alarmed so that if a fuse or circuit breaker has failed during
operation, a visual and audible alarm is activated. The system shall
be – Emergi-Lite® System CH (select model number from ordering
information chart). Select remote fixture from fixture section of
Catalogue.
The complete system is guaranteed for a period of one (1) year
against defects in workmanship and materials. The battery portion
of the equipment carries a ten (10) year pro-rata warranty during its
useful service life against defects in workmanship and materials.
The battery warranty is subject to the provision of normal testing
and inspection as specified in the Canadian Electrical Code, Section
46-102, and National Fire Code of Canada. Limit room ambient
temperature between 20°C to 25°C (68°F to 77°F). Optimum system
performance occurs at 25°C (77°F). A battery service life is defined
as the period which the battery could still provide at least 80% of its
rated capacity.
177
Project/Location:
Contractor:
CH Series
Date:
Prepared by:
DC Central Emergency Lighting System
SG SERIES :
FEATURES
• One set of dry contacts for remote fault sensings
Battery Capacity Chart
• Remote alarm panel
• Drip shield (2.5” overhang on console)
NOMINAL BACKUP CAPACITY
MODEL
30 MIN
60 MIN
90 MIN
120 MIN
• Brownout
A
CH24SG820
820W
490W
355W
285W
B
CH24SG1280
1130W
800W
585W
470W
C
CH24SG1875
1875W
1115W
815W
655W
D
CH24SG2250
2250W
1340W
975W
785W
CH24SG820-3755
CABINET DIMENSIONS
SERIES
DIMENSIONS H X W X D
25” X 29” X 14”
E
CH24SG2625
2625W
1560W
1140W
920W
CH36SG1230-3375
F
CH24SG3755
3755W
2235W
1630W
1315W
CH36SG3940
G
CH36SG1230
1230W
730W
537W
432W
CH120SG4120
H
CH36SG1920
1695W
1205W
880W
705W
CH120SG5660-11260
38” X 38” X 28”
CH120SG13140-22520
56” X 38” X 28”
I
CH36SG2815
2815W
1675W
1220W
985W
J
CH36SG3375
3375W
2010W
1465W
1180W
K
CH36SG3940
3940W
2345W
1710W
1380W
L
CH120SG4120
4120W
2450W
1790W
1440W
M
CH120SG5660
5660W
4015W
2935W
2355W
N
CH120SG9390
9390W
5590W
4080W
3290W
O
CH120SG11260
11260W
6700W
4890W
3940W
P
CH120SG13140
13140W
7820W
5710W
4600W
Q
CH120SG18780
18780W
11180W
8160W
6580W
R
CH120SG22520
22520W
13400W
9780W
7880W
38” X 38” X 18”
Electronics and batteries are in the same cabinet.
All capacities are in watts to 91% of nominal voltage. Note: For other voltages and
capacities contact your sales representative.
ORDERING INFORMATION
SYSTEM
DESIGNATION
CH
D.C. OUTPUT
VOLTAGE
24 = 24VDC
36 = 36VDC
120 = 120VDC
BATTERY
TYPE
SG= sealed
LeadCalcium
CAPACITY IN
WATTS
__________*
OPERATING
TIME
30 = 30 min
60 = 60 min
90 = 90 min
120 = 120
min
* Select from
Battery
Capacity chart
in folder
A.C. INPUT
VOLTAGE
(1PH)
120 = 120VAC
208 = 208VAC
240 = 240VAC
277 = 277VAC
347 = 347VAC
600 = 600VAC
TRANSFER
OPTIONS
DISTRIBUTION
OPTIONS
OPTIONS
CP= n
ormally off
load
ormally on
TS= n
load
ormally
CP/TS= n
on and off
load*
OPF= f use
panel*
OFA= f use
panel with
alarm
CBO= c ircuit
breaker
panel*
OCA= c ircuit
breaker
panel
with
breaker
trip alarm
TD= Time delay
(15 minutes)*
3PH= 3 phase
sensing
12HR= 12 hour
recharge
attery
CYC= B
exerciser
BCB= Battery
circuit
breaker
ZSC= Common
zone
sensing**
* Specify time.
*Specify Watts for
each type of load.
178
*Specify number
of circuits
** Specify No. of
zones.
SNAP III
NEXUS
SNAP I
BULB
SNAP II
EZ2
SUSPENSION
RETROFIT KITS
OPTIONS &
ACCESSORIES
Project/Location:
Contractor:
TABLE OF CONTENTS
Date:
Prepared by:
LED RETROFIT KITS
LED BULB SERIES
48 & FPS SERIES
EZ2 CANOPY
PENDANT KIT
WIRE GUARDS
NEXUS
P. 184-185
P. 186
P. 187
P. 188
P. 189
P. 190-191
P. 192-193
183
Project/Location:
Contractor:
LED Retrofit Kits
Date:
Prepared by:
Convert high-consumption incandescent and
fluorescent lamps to energy-efficient LED lamps
Converting existing Exit Signage from incandescent or fluorescent
lamps to LED (light emitting diodes) lamps drastically reduces
operating and maintenance costs for building owners and property
managers. As part of energy-efficiency programs, some Canadian
electric utilities are also actively promoting conversion to LED with
incentive and rebate programs for installers and building owners/
managers.
FEATURES
Emergi-Lite® offers four retrofit kit options; all
based on the long-life ALINGAP LED technology:
•
•
•
•
SNAP II SERIES
•Q
uick and easy to install
• Long-life, energy-efficient red ALINGAP LED technology
• Module features two independent circuits – one for AC input; one
for DC input
• Universal AC input: 120/277/347VAC; universal two-wire DC input: 6 to
24VDC
• Power consumption of 1.1W per module
• 10 year limited warranty
NAP II Series
S
SNAP III Series
SNAP I Series
Bulb Series
Benefits of using LED lamps in Exit Signs:
•E
xceptional energy-efficiency – reduces energy consumption by
up to 90%
• Extremely long life – 10 to 25 years
• Important reduction in maintenance and energy costs
• Average payback is less than two years (see page 6)
• Retrofit kits are easy to install
• Improved visibility and reliability: ALINGAP LED technology
DIMENSIONS
Dimensions are approximate and subject to change.
28
1/8 ” [
11
TYPICAL SPECIFICATION
.3 c
13/16” [2.1
cm]
m]
Converting existing exit signage from incandescent or fluorescent
lamps to LED (light emitting diodes) lamps drastically reduces
operating and maintenance costs for building owners and property
managers.
As part of energy efficiency programs, some Canadian electric
utilities are also actively promoting conversion to LED with incentive
and rebate programs for installers and building owners/managers.
13/16” [3 cm]
POWER CONSUMPTION
MODEL
SNAP II
AC SPECS
120/277/347VAC
DC SPECS
1.1W
6 to 24VDC
1.3W
ORDERING INFORMATION
SERIES
SNAP II= hardwire retrofit kit
11.0” (28cm) long
SNAP IIB= hardwire retrofit kit
9.5” (24cm) long*
*Available in UN voltage only.
EXAMPLE: SNAPII-UN
184
VOLTAGE
-UN= 120/277/347VAC, 6/12/24VDC
-U36= 120/277/347VAC, 36VDC
-U48= 120/277/347VAC, 48VDC
-U120= 120/347VAC, 120VDC
-120V-1H2= 120VAC,120VDC, 2 wires
Project/Location:
Contractor:
LED Retrofit Kits
Date:
Prepared by:
New Design:
0.65W; 60% off power consumption.
SNAP III SERIES
•
•
•
•
•
•
SNAP I SERIES
asiest to install in its class
E
Compact size makes it ideal for virtually all Exit Signs
Can be retrofitted directly on fluorescent ballast
Long-life, energy-efficient red ALINGAP LED technology
Available with AC adaptor for all types of lamp sockets
10 year limited warranty
asiest to install in its class
E
Compact size makes it ideal for virtually all Exit Signs
Can be retrofitted directly on fluorescent ballast
Suitable for all AC line applications including Exit Signs equipped
with in-line diodes
• Long-life, energy-efficient ALINGAP LED techonology
•
•
•
•
DIMENSIONS
DIMENSIONS
Dimensions are approximate and subject to change.
Dimensions are approximate and subject to change.
1/2
9
” [2
4.1
cm
]
13/16
” [2.1 cm]
1/2
9
” [2
4.1
cm
]
13/16
” [2.1 cm]
13/16” [3 cm]
13/16” [3 cm]
POWER CONSUMPTION
MODEL
SNAP III
AC SPECS
POWER CONSUMPTION
DC SPECS
120VAC; 86VAC step down from
347VAC
0.65W
N/A
MODEL
N/A
SNAP I
ORDERING INFORMATION
SERIES
SNAP III= for standard applications
AC SPECS
120VAC; 120VAC with in-line
diodes
DC SPECS
2.8W
N/A
ORDERING INFORMATION
BASE
SERIES
-C= candelabra
-I= intermediate
-M= medium
-B= bayonet
-F= G23 compact fluorescent
-UN= complete set of bases
(excludes “F” base)
-H= 120VAC (hardwire)
-2H= 277VAC (hardwire)
-3H= 347VAC (hardwire)
SNAP I = with or
without
in-line
diodes
EXAMPLE: SNAPIII-C
EXAMPLE: SNAPI-C
185
BASE
-C= candelabra
-I= intermediate
-M= medium
-B= bayonet
-F= G23 compact fluorescent
-UN= complete set of bases (excludes “F” base)
-H= 120VAC (hardwire)
-2H= 277VAC (hardwire)
-3H= 347VAC (hardwire)
N/A
Project/Location:
Contractor:
LED Retrofit Kits
Date:
Prepared by:
TYPICAL SPECIFICATIONS
The following is an example of the savings you can generate by simply
installing an LED retrofit kit in an existing incandescent Exit Sign.
The Retrofit Kit Cost:
Installation cost (per unit) for a
retrofit kit (Labour):
Wattage rating per incandescent lamp in
existing fixture:
Number of incandescent lamps per
fixture:
BULB SERIES
• Quick
and easy to install
• Available with a wide range of lamp bases for quick lamp to lamp
replacement
• Long-life, energy-efficient ALINGAP LED techonology
• 120VAC or 120VAC with in-line diode
DIMENSIONS
Dimensions are approximate and subject to change.
15/16
11/4” [3.2 cm]
” [2.5 cm]
33/4” [9.6 cm]
33/4” [9.6 cm]
43/4” [12 cm]
51/3” [13 cm]
13/16
MODEL
4 Months
My replacement labour cost:
$25.00/Hour
Estimated lamp replacement
time per exit:
20 Minutes
Current material cost for each
Exit Sign lamp:
$1.00/Lamp
DC SPECS
BULB I
120VAC
0.90W
N/A
N/A
BULB II
120VAC
2.6W
120VDC
2.6W
ORDERING INFORMATION
SERIES
BULBI/HB= standard version
BULBII/HB= with or without in-line diodes
(2.5W), high brightness
BASE
C= candelabra
I= intermediate
M= medium
B= bayonet
F= G23 compact
fluorescent
EXAMPLE: BULBI-C
186
$0.060/$ Per kWh
THE PAYBACK FOR YOUR INSTALLATION IS:
1.06 Years
THE ANNUAL RETURN ON INVESTMENT IS:
94.50 %
For more information, please consult your sales representative.
AC SPECS
2
My existing incandescent exit lamps last
for:
” [2.1 cm]
POWER CONSUMPTION
15W
1.7W
ANNUAL SAVINGS:
” [2.1 cm]
$5.00
Wattage rating of Emergi-Lite LMRUNIV
retrofit kit:
My current energy cost:
13/16
$70.00
$70.87
Project/Location:
48 Series &
FPS Series
Contractor:
Date:
Prepared by:
Fluorescent Inverters
FEATURES
TYPICAL SPECIFICATIONS
All FPS Series are fully load tested prior to shipment
Inverter is 100% solid state, short and open circuit proof
Polarized DC input (48 Series only)
120VAC 60Hz input is standard, 277 and 347VAC available as
options
• 25%, 50% or 80% lamp lumen output
• Mounts directly in ballast channel, remote or optional
T-Bar fixture
• CSA listed
•
•
•
•
48 Series: The electrical contractor shall supply and install
Emergi-Lite® 48 Series remote fluorescent inverter ballasts for
each fixture as shown on plans. The inverter shall operate on
VDC input for
minutes during a power failure.
The fluorescent lamp shall be maintained at
% lumen
output for one lamp only. The inverter is to be connected to the
remote battery unit as shown on plans (battery unit to be selected
according to voltage/wattage and duration required). The inverter
shall be capable of illuminating the fluorescent lamp even when it
is burned out under normal AC operation.
FPS Series: The electrical contractor shall supply and install
Emergi-Lite® FPS Series fluorescent inverters for each fixture
as shown on plans. The FPS Series inverter shall operate for
minutes during a power failure. The fluorescent lamp
shall be maintained at
% of nominal lumen output.
The FPS Series inverter shall be capable of illuminating the
fluorescent lamp even when it is out under normal AC operations.
.
DIMENSIONS
Dimensions are approximate and subject to change.
INTERNAL ENCLOSURE (BLACK)
71/4”
[18.4 cm]
23/4”
[7 cm]
151/4” [38.7 cm]
31/4”
[8.3 cm]
T ENCLOSURE (FACTORY WHITE)
11/2” [3.8 cm]
R ENCLOSURE (WHITE)
45/8”
[11.7 cm]
233/4” [60.3 cm]
48 ENCLOSURE (WHITE) - INTERNAL
3” [7.6 cm]
11/2” [3.8 cm]
41/2”
[11.4 cm]
207/8” [53 cm]
95/8” [24.4 cm]
D.C. POWER CONSUMPTION
ORDERING INFORMATION 48 SERIES
48 SERIES
4806= 6V
4812= 12V
4824= 24V
4832= 32V
4848= 48V
48120= 120V
VOLTAGE
SERIES
OUTPUT %
LUMENS
W
Blank= 120VAC
-2= 277VAC
-3= 347VAC
FPS-800
25
800
10
FPS-1600
50
1600
20
FPS-3200
80
2560
32
LUMENS / (%) FOR 48” TUBE
25= 25% (800 lumens)
Lumen outputs based on averages.
60= 50% (1600 lumens)
24”/20W=1260 48”/40W=3200
96”/75W=6300
100= 80% (2560 lumens)
Inverters will operate T12, T8, or
“U” type lamps.
21/2”
[6.4 cm]
EXAMPLE: 4812-25-3
ORDERING INFORMATION FPS SERIES
SERIES
FPS
LUMENS / (%) FOR 48” TUBE
25= 25% (800 lumens)
Lumen outputs based on averages.
60= 50% (1600 lumens)
24”/20W=1260 48”/40W=3200 96”/75W=6300
100= 80% (2560 lumens)
Inverters will operate T12, T8, or “U” type lamps.
MIN. RUNTIME
HOUSING
30= 30 minutes
60= 60 minutes
90= 90 minutes
120= 120 minutes*
Blank= internal*
R= remote mounting enclosure
T= T-Bar
*FPS100 in T-Bar cabinet only.
*Not available for FPS100.
EXAMPLE: FPS60/30
187
AC VOLTAGE
Blank= 120VAC
-2= 277VAC
-3= 347VAC
Project/Location:
EZ2 Canopy
™
Quick and Easy Installation
Contractor:
Date:
Prepared by:
DIMENSIONS
Dimensions are approximate and subject to change.
63/8”
The EZ2™ Canopy allows the installer to make all of the electrical
connections using both hands without having to juggle with the Exit
Sign, making it our most contractor friendly product feature to date.
11/32”
Simply attach the backplate to the junction box, clip the canopy
on the Exit Sign, hang the canopy on the back plate, make your
connections using both hands, slide the unit in place, one screw and
the job is done!
411/16”
See detail A
See detail C
See detail B
3. Connect the wires, then align and slide
the sign to its final position.
1. Attach the backplate/spider to the
wall before assembly.
2. Hang the unit using
the tabs and the wire eyes.
Detail A
Scale 3.000
Detail C
Scale 3.000
Detail B
Scale 3.000
188
Project/Location:
Contractor:
Pendant Kit
Date:
Prepared by:
TYPICAL SPECIFICATIONS
DIMENSIONS
Offered in a variety of colours and lengths, Emergi-Lite® Pendant
Kits are designed to facilitate the installation of Exit Signs at regular
mounting heights.
Dimensions are approximate and subject to change.
P1E
Compatible with both horizontal and sloped ceilings, these Pendant
Kits are truly universal and will adapt to any application.
Length
Please consult your sales representative.
P2E
ORDERING INFORMATION
SERIES
LENGTH (IN)
COLOUR
P1E*
6
12
18
24
W= white
B= black
SG= silver grey
P2E*
6
12
18
24
W= white
B= black
SG= silver grey
P23E*
Edge-Lit
6
12
18
24
W= white
B= black
SG= silver grey
P4E*
New Premier™ Plastic Exit
6
12
18
24
W= white
B= black
*Other lengths available on demand. Consult your sales representative.
189
Project/Location:
Contractor:
Wire Guards
Date:
Prepared by:
EXIT SIGNS
PART #
MOUNTING
DIMENSIONS
SIGNS
W
H
D
10 1/2”
(26.7 cm]
6”
(15.2 cm)
16”
(40.6 cm)
14 1/2”(36.8 cm)
6 1/4”
(15.9 cm)
10 1/2”
(26.5 cm)
28 1/8”
(71.5 cm)
21 1/8”
(53.7 cm)
10”
(25.4 cm)
End Mount
LPEX100
LPEX50
LPEX600-N Series - Nema-4X
Exit
EX160
LPEX300
460.0028-E
Ceiling Mount
LPEX100
LPEX50
LPEX600 - Nema-4X
EX160
460.0034-E
Wall Mount
12ESL-SR Sortie
WP36
LPEX300
EX10
EN
SR160
ES
12ESL-EX
C8SRPK-P
460.0048-E
End Mount
LPSR100
C8SR50
LPSR300
C8SR10
10 1/2”
(26.7 cm)
6”
(15.2 cm)
21”
(53.3 cm)
460.0057-E
Wall Mount
LPSR100
C8SR50
LPSR300
C8SR10
20 3/4”
(52.7 cm)
10” (25.4 cm)
4” (10.2cm)
460.0058-E
Ceiling Mount
LPSR100
C8SR50
LPSR300
C8SR10
21 3/4”
(55.2 cm)
5 1/2”
(14 cm)
10 1/2”
(26.7cm)
460.0059-E
Wall Mount
C8ES300 bilingual
C8SE10
C8ES70 bilingual
C8ES10
460.0060-E
End Mount
LPEX600-N - Nema-4X Combo
EX10-P
460.0060-E
Wall Mount
EN
LPEX600-N Combo
EX10-P
31”
(86.4 cm)
20”
(50.8 cm)
20”
(50.8 cm)
10”
(25.4 cm)
12”
(30.5 cm)
12”
(30.5 cm)
4 1/2”
(14 cm)
15”
(38.1 cm)
15”
(38.1 cm)
460.0078-E
Wall Mount
C8SR50-P Combo
LPEX600-N - Nema-4X Combo
EX10-P
ENC
Premier™ Combo
18”
(45.7 cm)
18”
(45.7 cm)
7”
(17.8 cm)
460.0079-E
Wall Mount
LPEX100
LPEX50
LPEX600 - Nema-4X
EX160
LPEX300
EX10
Premier™ Exit
EN
ES
SR160
14 1/4”
(36.2 cm)
9 7/8”
(25.0 cm)
4 5/8”
(11.7 cm)
460.0080-E
Wall Mount
EXHZ combo (class1 Div2)
LPEXHZ Exit
15 1/4”
(38.7 cm)
14 1/8”
(35.9 cm)
6 1/2”
(16.5 cm)
460.0081-E
Wall Mount
12ESL-EX, EAC, EX10-P,
SR, ESC
20”
(50.8 cm)
17 1/8”
(43.6 cm)
8 1/2”
(21.6 cm)
460.0091-E
Wall Mount
EX10-P
15”
(38.1 cm)
10 1/2”
(26.7 cm)
1”
(2.5 cm)
460.0092-E
Ceiling Mount
C8SR10
C8ES300 Bilingual
C8ES70
31”
(53.3 cm)
4.5”
(11.4 cm)
10”
(25.4 cm)
460.0103-E
Wall Mount
C8SRPK-P
25” (63.5 cm)
15” (38.1 cm)
6” (15.2 cm)
25” (63.5 cm)
10” (25.4 cm)
20” (50.8 cm)
460.0027-E
460.0104-E
End Mount
EX10
EN
SR160
ES
EX10-P
C8ES70
C8E/S35R
C8SR10
190
Project/Location:
Contractor:
Wire Guards &
Mounting Shelves
Date:
Prepared by:
BATTERY UNITS
PART
MOUNTING
460.0078-E
Wall Mount
460.0081-E
460.0034-E
460.0097-E
DIMENSIONS
COMMERCIAL, DECO UNIT
W
H
D
“A” Cabinet-6V, 12V, 24V-Max. 144W
8”
(45.7 cm)
8”
(45.7 cm)
7” (17.8 cm)
Wall Mount
“B” Cabinet-6V-180W
12V-200 to 360W
24V-200 to 288W
20” (50.8 cm)
17 1/8”
(43.6 cm)
8 1/2”
(21.6 cm)
28 1/8”
(71.5 cm]
21 1/8”
(53.7 cm)
10” (25.4 cm)
Wall Mount
“C” Cabinet-12V-650watts
24V-350 to 720W
Q-BIC
31”
(53.3 cm)
70”
(17.8 cm)
6”
(15.2 cm)
SMALL, 6V
460.0080-E
Wall Mount
15 1/4”
(38.7 cm)
6V, 12V - 18 to 72W
14 1/8”
(35.9 cm)
6 1/2”
(16.5 cm)
9” (3.5 cm)
9” (3.5 cm)
17 1/8”
(43.6 cm)
8 1/2”
(21.6 cm)
INDUSTRIAL
460.0082-E
Wall Mount
460.0081-E
Small Cabinet
12” (30.5 cm)
Medium and Large Cabinet
20” (50.8 cm)
REMOTE HEADS
DIMENSIONS
REMOTE HEADS
PART #
W
H
8 1/4” (21.5 cm)
D
460.0029-E
EF9, EF9Q, EF9M, EF11, EF25
6 1/4” (15.9 cm)
6 3/4” (17.2 cm)
460.0031-E
EF26D, EF18T, EF11D
460.0032-E
EF26DS, EF150
25 1/4” (64.1 cm)
8 1/2” (21.5 cm)
8 1/2” (21.5 cm)
9 1/2” (24.1 cm)
9 1/2” (24.1 cm)
6 1/8” (15.6 cm)
460.0033-E
460.0035-E
EF15
9 1/2” (24.1 cm)
9 1/2” (24.1 cm)
4”(10.2 cm)
EF18, EF11, EF30, EF26, EF39, EF40
8 1/4” (21.5 cm)
6 1/4”(15.9 cm)
8 1/2” (21.5 cm)
460.0082-E
EF18D, EF11D, EF30D, Literay™, Lux-Ray™, Retract-a-Lite™
12”(30.5 cm)
9”(22.9 cm)
9”(22.9 cm)
460.0100-E
Provider™
14”(35.6 cm)
5.8”(14.7 cm)
5.6”(14.2 cm)
MOUNTING SHELVES
PART # 440.0620-E FOR “B” CABINET
71/2”
[19.05 cm]
81/32”
[20.4 cm]
115/16” [28.7 cm]
151/16” [38.28 cm]
51/16”
[12.89
cm]
81/32”
[20.4 cm]
111/32” [28.02 cm]
71/2”
[19.05 cm]
1029/32” [27.69 cm]
PART # 440.0625-E FOR “C” CABINET
181/16” [45.85 cm]
63/16”
[15.75 cm]
191
111/16” [28.07 cm]
PART # 440.0616-E FOR “A” CABINET
253/32” [63.75 cm]
69/32”
[15.93 cm]
NEXUS® EMERGENCY LIGHTING
MANAGEMENT SYSTEM
MAXIMIZE SYSTEM AVAILABILITY
ARE YOU PREPARED FOR A SAFETY
INSPECTION?
By allowing maintenance personnel to easily maintain and monitor
the emergency lighting system without having to manually check
each unit, Nexus® reduces the hours required to disrupt the power
supply for inspections. With Nexus®, monthly tests and reports on the
status of all emergency lights and exit signs can be done individually,
in groups, or together.
Building & Life Safety Codes oblige building owners/managers to
ensure the safe evacuation of a building in the event of an emergency.
In the interest of public safety, building owners/managers must meet
the outlined requirements for exit signs and emergency lighting
equipment, including the following:
Advantages of the Nexus® system include saving labor; maximizing
system availability by testing units in groups and stages rather than
setting all units in recovery mode; and the convenience of selfmonitoring. Nexus® indicates the location of a faulty unit and reports
it instantly without requiring a manual search.
• Conduct a discharge test every month.
• Conduct functional tests annually.
• Keep a log book of maintenance information.
Complying with these requirements can be labour intensive and costly,
especially in large buildings where testing every emergency light
requires many man-hours.
UPDATE STATUS INSTANTLY
Disrupting the power supply during lengthy inspections can also put
public safety at risk.
Nexus® passes messages both to and from the emergency units to
instruct the units to perform all mandatory testing by communicating
between the emergency units and a centrally located controller.
MANAGE TESTING WITH NEXUS® TO SAVE
TIME AND COSTS
Nexus® is a proven system supported by a 5-year warranty, and can
contribute to LEED certification and support green building initiatives.
Nexus® is a real-time monitoring system that manages the status of
your entire Emergency Lighting and Exit Sign system from a central
control unit. Nexus® runs diagnostics, performs required monthly
and annual functional tests, generates maintenance logs and runs
compliance reports.
Available in wired or wireless (RF) versions, Nexus® installations often
pay for themselves in less than two years. In addition to operational
savings, Nexus® helps increase system reliability and performance
and reduces the risk of failed inspections. One building or a group
of properties under the same management can be monitored with
Nexus®.
192
SMALL SYSTEM EXAMPLE
In a system of fewer than 100 units it is most likely that the only
hardware required, other than the emergency units themselves,
is a controller. All communication would occur wirelessly and
installation would not vary greatly from a non-monitored system.
Once the units are in place, the system will establish the mesh
network. The building itself could be quite large as each unit
only needs to be able to communicate with its close neighbours
and does not need to communicate directly with the controller.
LARGE SYSTEM EXAMPLE
The Nexus ® RF system has been designed to be extremely
flexible and provides for a range of system options. Each large
site will need to be assessed for the best system solution with
the assistance of Thomas & Betts technical staff.
The basic Nexus® RF system is designed to run on an Ethernet
network which is present in most modern buildings; however,
through a range of interface cards the backbone of the network
could be WLAN.
As with the small system example, site performance will be
optimized through the careful selection and placement of Area
Controller Routers and the Area Controller to form efficient
clusters. Building layout and materials will also play some role
in determining the best solution to deliver a highly effective
means of testing and maintenance requirements.
193
TECHNICAL
INFO
ELECTRICAL
CODE
BUILDING
CODE
WARRANTY
TECHNICAL
INFORMATION
195
Project/Location:
Contractor:
TABLE OF CONTENTS
Date:
Prepared by:
Project/Location:
Project/Location:
Contractor:
Wire Size Guide
What is Emex?
Date:
Prepared by:
When remote fixtures and exit signs are connected to emergency lighting units of less than 50 volts, circuit runs must be sufficient size to maintain a
proper operating voltage to all lamps. The maximum allowable voltage drop should not exceed 5%. Proper wire size can be selected from the following
table or by use of the following formula:
CM= Wire size in circular mills
W= Emergency load in watts
L= Length of circuit in feet
CM = 22 X W X2 L
.05 X E
LENGTH OF WIRE RUN (in feet)
6V
13
18
25
30
35
50
60
75
100
150
200
250
300
400
12
10
8
41
65
110
30
47
75
21
32
54
18
28
45
15
24
39
11
17
27
9
14
22
8
11
18
6
9
14
4
6
9
__
__
7
__
__
__
__
__
__
__
__
__
6
12
12V
10
8
6
4
12
24V
10
8
6
4
12
10
32V
8
6
4
12
48V
120V
10
8
6
165
165
260
415
660
1050
660
120
110
190
300
475
760
440
1040
1668
2640
760
1200
1900
4200
3040
1160
__
840
1340
__
__
__
__
__
__
__
1899
__
__
__
__
__
__
86
85
136
215
340
540
340
71
71
112
180
285
455
284
62
43
61
42
97
154
68
108
245
390
170
275
244
168
544
860
1360
448
720
1140
388
616
980
272
432
680
2160
1810
1560
1100
36
35
52
90
140
225
140
208
360
560
900
29
29
45
72
114
182
116
180
288
456
500
800
435
690
300
480
1280
__
1110
1740
770
1220
640
1020
510
815
__
1620
1300
__
__
__
250
400
728
600
960
1540
__
200
320
22
21
34
54
86
137
84
136
216
344
548
150
240
385
610
970
1367
1139
949
680
__
455
341
__
__
__
1811
__
__
1509
__
__
1085
1729
__
__
__
__
724
1152
1832
543
864
1374
15
14
23
36
57
91
56
92
144
228
364
100
160
255
405
650
227
362
576
916
11
10
17
27
43
68
40
68
108
172
272
75
120
192
305
485
170
9
8
14
21
34
55
32
52
84
136
220
60
96
154
240
390
136
__
__
11
18
28
45
26
Performance
__
The EMEX-Power Systems work with lighting loads to provide
full light output for minimum 30 min. It is designed to support
incandescent, fluorescent and LED loads. It will power these loads at
cold starts for all normally off circuits or normally on circuits.
__
__
__
__
113
68
108
172
274
7792
__
__
3896
__
__
1945
1300
977
__
__
12367
19705
__
__
__
__
6193
9852
__
__
__
__
3093
4820
2067
3289
1553
2471
720
1238
650
1033
60159
__
31327
__
__
15663
__
__
7822
5229
3929
1970
1644
608
966
1538
3132
2614
2445
EMEX-Power Systems can be used in almost every type of
building, especially in architecturally sensitive applications or
when maintenance costs and testing of individual unit equipment
becomes significant. Our systems are designed to work with power
factor corrected as well as the most recent T5 and T5-HO electronic
ballasts.
BENEFITS
SELF-DIAGNOSTIC/SELF-TESTING
Programmable monthly and annual self-testing. Proven selfdiagnostic with information stored in separate memory logs for
Test, Event and Alarm. Microprocessor monitoring and control.
42
63
100
163
260
181
288
458
__
23787
37810
Approvals
- CSA C22.2 No. 141-10 – Emergency Lighting Equipment
- CSA C22.2 No. 107.3 – Uninterruptible Power Systems
- UL 1778 – Uninterruptible Power Systems
Applications
FEATURES
21
34
54
85
100
50
80
128
200
325
217
345
549
14964
10
8
6
The product is third generation inverter technology. LVD (Low Voltage
Disconnect) circuitry eliminates excessive battery drain after long
power outages.
Batteries
Automatic restart and recharge upon restoration of utility.
SERIES HIGHLIGHTS
__
44
72
112
180
271
432
687
12
COMPLIANCE WITH NFPA101
The self-testing meets the requirements of NFPA and UL. User
programmable time of testing. Test results, events or alarms
can be downloaded from history logs. Load monitoring. Reduced
testing/service time.
LOW HEAT DISSIPATION
Very low heat loss in standby operating mode (see specifications
for exact values). Convection cooling in normal mode with forced
air during emergency and recharge mode. Battery cabinets:
convection cooling only.
LESS AIR-CONDITIONING
Reduced costs for air-conditioning required to ensure the optimum
operating temperature when compared with equivalent systems
that dissipate much more heat. Higher reliability of fans and
electronic components.
VERSATILE INSTALLATION
Modular design, easy front access freestanding cabinets,
fasten together when more than one cabinet is required.
Optional seismic kit available. All wiring provided is pre-cut
and terminated, along with the necessary hardware for proper
installation.
EASY TO INSTALL
Quick installation and connection through flexible cable entries and
fast access terminal blocks. Low MTTR (<30 min.) due to modular
design, quick disconnect means and frontal access.
COMPLETE PROTECTION
Battery circuit breakers are standard. Modular standard systems
offer overload capacity, short-circuit protection, current- limiting,
low-battery disconnect and brownout protection as standard.
REDUCED DAMAGE RISKS
The full protection of the system will eliminate damage created by
external events and will increase lifetime of the electronics and the
batteries.
Date:
MR16 LED LAMP BENEFITS
With the remarkable technology development in the last
decade, the light-emitting diode (LED) is becoming the
preferred solution in low- and medium-power lighting
applications. The emergency lighting industry is no
exception: today virtually every new product introduced to
market includes “white” LEDs for emergency illumination.
• CSA C22.2 No. 141 certified.
• Energy-efficient LED MR16 lamp provides equivalent
lighting performance to a much higher watt halogen
MR16 lamp.
• Reduces required battery capacity by 75%, providing
necessary illumination with fewer remote heads and
battery units for project cost savings.
Extremely efficient and long-lasting, LED lamps become the
natural alternative to incandescent lamps due to three main
advantages:
Wire Size Guide
Wire Size Guide
MR16 LED EMERGENCY LIGHTING
Wire Size Guide
6V
510-LUMEN 6W MR16 LED
New in Fall 2013, we intoduce a 12V - 6W MR16 LED lamp,
which offer typical luminous flux of 510 lumens. Like the
lower wattage MR16 LED lamps, this new lamp is specially
designed for emergency lighting. It offers the same lighting
preformance as the 35W or 20W Mr16 IR. A twin emergency
head installed at a height of 7.5’ illuminates approximately
100’ path of egress.
12V
INCREASED MTBF
Increased reliability and reduced preventative maintenance. No air
filters needed.
MONITORING AND CONTROL
User friendly programmable interface with LCD display provides
full metering values, easy program and control functions and a
wide range of visual and audible alarms.
25
30
35
50
60
75
100
150
200
250
300
400
30
47
75
21
32
54
18
28
45
15
24
39
11
17
27
9
14
22
8
11
18
6
9
14
4
6
9
__
__
7
__
__
__
__
__
__
__
__
__
10
8
6
4
10
8
6
4
12
10
8
6
4
12
48V
40-FT. PATH OF EGRESS 2 X 4W MR16 LED
EASY MAINTENANCE
Diagnostics, troubleshooting, preventative maintenance and
service are made easier by using the front panel display or the
history logs.
18
41
65
110
12
24V
32V
10
8
6
165
165
260
415
660
1050
660
120
110
190
300
475
760
440
1040
1668
2640
760
1200
1900
4200
3040
1160
__
840
1340
__
__
__
__
__
__
__
1899
__
__
__
__
__
__
86
85
136
215
340
540
340
71
71
112
180
285
455
284
62
43
61
42
97
154
68
108
245
390
170
275
244
168
544
860
1360
448
720
1140
388
616
980
272
432
680
2160
1810
1560
1100
36
35
52
90
140
225
140
208
360
560
900
29
29
45
72
114
182
116
180
288
456
500
800
435
690
300
480
1280
__
1110
1740
770
1220
640
1020
510
815
__
1620
1300
__
__
__
250
400
728
600
960
1540
__
200
320
22
21
34
54
86
137
84
136
216
344
548
150
240
385
610
970
1367
1139
949
680
__
455
341
__
__
__
1811
__
__
1509
__
__
1085
1729
__
__
__
__
724
1152
1832
543
864
1374
When remote fixtures and exit signs are connected to emergency lighting units of less than 50 volts, circuit runs must be sufficient size to maintain a
proper operating voltage to all lamps. The maximum allowable voltage drop should not exceed 5%. Proper wire size can be selected from the following
table or by use of the following formula:
E= Line Voltage
22= Constant
.05= Factor for max. allowable
voltage drop
CM= Wire size in circular mills
W= Emergency load in watts
L= Length of circuit in feet
CM = 22 X W X2 L
.05 X E
LENGTH OF WIRE RUN (in feet)
13
12
10
8
6
Keeping pace with technology, in 2012 we introduced a
12V-5W MR16 LED lamp. With a typical luminous flux of 340
lumens, this lamp has the same lighting performance as
a 20W high-output halogen MR16. A twin emergency head
installed at a height of 7.5ft illuminates more than a 70ft
path of egress.
Compared to halogen lamps (16-20W), these 4W MR16
LED lamps illuminate the same area of egress during an
emergency situation by using 75% less power. This has
a direct impact on the battery size, reducing the back-up
capacity needs by 75%. Consequently, it also reduces the
total cost of the application, with the use of smaller battery
capacity units, the possibility of using fewer fixtures due to
superior illumination, thus also reducing electrical wiring,
and it it reduces the environmental footprint.
CM= Wire size in circular mills
W= Emergency load in watts
L= Length of circuit in feet
CM = 22 X W X2 L
.05 X E
WATTS
WIRE
SIZE
12
340-LUMEN 5W MR16 LED
200-LUMEN 4W MR16 LED
Leading the technology trend, Emergi-Lite® offers a
complete series of 4W MR16 LED lamps available for all
the standard battery voltages: 6V, 12V, 24V and 120V. With
up to 30,000 hours of operational life and a luminous
flux of typically 200 lumens, they are available with most
emergency heads designed to hold an MR16 lamp and meet
the majority of illumination specifications. For example: one
pair of LED emergency heads installed at a height of 7.5ft,
illuminates a 6ft by 40ft path of egress.
When remote fixtures and exit signs are connected to emergency lighting units of less than 50 volts, circuit runs must be sufficient size to maintain a
proper operating voltage to all lamps. The maximum allowable voltage drop should not exceed 5%. Proper wire size can be selected from the following
table or by use of the following formula:
E= Line Voltage
22= Constant
.05= Factor for max. allowable
voltage drop
LENGTH OF WIRE RUN (in feet)
• Vibration-resistant LED stands up to industrial
environments.
• Ideal for indoor and outdoor use.
CM= Wire size in circular mills
W= Emergency load in watts
L= Length of circuit in feet
CM = 22 X W X2 L
.05 X E
• Small profile, compact white lighting is ideal for
architectural applications.
• = lamp efficacy: 50 - 70 lumen per watt compared to 15 30 lumen per watt of the best halogen lamp.
• = operational life: 30,000+ hours, equivalent to a lifetime
warranty in emergency lighting.
• = lower lamp temperature (80 - 120°C) is a huge benefit
for lighting in hazardous locations.
Contractor:
Date:
Prepared by:
When remote fixtures and exit signs are connected to emergency lighting units of less than 50 volts, circuit runs must be sufficient size to maintain a
proper operating voltage to all lamps. The maximum allowable voltage drop should not exceed 5%. Proper wire size can be selected from the following
table or by use of the following formula:
120V
THERMAL PERFORMANCE
Bonded oversized heat sinks for maximum thermal performance.
Cooling fans are energized only in inverter and recharge modes.
188
Project/Location:
Contractor:
Prepared by:
MR16 LED ILLUMINATION
True Sine Waveform
Using a solid-state, pulse width modulation (PWM) inverter, the
systems produce pure sinusoidal output waveform with less than 5%
Total Harmonic Distortion (THD) for linear loads.
Reliability
Each module has input and output protection and each module
measures and limits its own current.
Alarms and status indications are provided on the front panel display,
which provide clear and concise information, rather than a long list of
parameters, which may be confusing.
WATTS
WIRE
SIZE
MR16 LED EMERGENCY LIGHTING
A General Presentation about Emex Central Systems
SYSTEM DESIGN
The EMEX Power inverter and charger modules utilize solid state
electronics of the highest reliability to provide a rugged, easy to
maintain system with exceptional performance for emergency
lighting use. The system has been designed solely for emergency
lighting, and not modified from other less essential power supply
requirements. As such, the system has exceptional overload
performance without the need to over-specify the rating of the
inverter to ensure faults can be cleared.
E= Line Voltage
22= Constant
.05= Factor for max. allowable
voltage drop
15
14
23
36
57
91
56
92
144
228
364
100
160
255
405
650
227
362
576
916
11
10
17
27
43
68
40
68
108
172
272
75
120
192
305
485
170
9
8
14
21
34
55
32
52
84
136
220
60
96
154
240
390
136
__
__
11
18
28
45
26
__
113
108
172
274
7792
__
__
3896
__
__
1945
1300
977
__
__
12367
19705
__
__
__
__
6193
9852
__
__
__
__
3093
4820
2067
3289
1553
2471
720
1238
650
1033
60159
__
31327
__
__
15663
__
__
7822
5229
3929
1970
1644
608
966
1538
3132
2614
2445
30
35
50
60
75
100
150
200
250
300
400
21
32
54
18
28
45
15
24
39
11
17
27
9
14
22
8
11
18
6
9
14
4
6
9
__
__
7
__
__
__
__
__
__
__
__
__
10
8
6
4
10
8
6
4
12
10
32V
8
6
4
68
181
288
458
__
23787
37810
25
30
47
75
12
24V
42
63
100
163
260
217
345
549
14964
10
8
6
18
41
65
110
12
12V
21
34
54
85
100
50
80
128
200
271
432
687
12
13
12
10
8
12
48V
120V
10
8
6
165
165
260
415
660
1050
660
120
110
190
300
475
760
440
1040
1668
2640
760
1200
1900
4200
3040
1160
__
840
1340
__
__
__
__
__
__
__
1899
__
__
__
__
__
__
86
85
136
215
340
540
340
71
71
112
180
285
455
284
62
43
61
42
97
154
68
108
245
390
170
275
244
168
544
860
1360
448
720
1140
388
616
980
272
432
680
2160
1810
1560
1100
36
35
52
90
140
225
140
208
360
560
900
29
29
45
72
114
182
116
180
288
456
500
800
435
690
300
480
1280
__
1110
1740
770
1220
640
1020
510
815
__
1620
1300
__
__
__
250
400
728
600
960
1540
__
200
320
22
21
34
54
86
137
84
136
216
344
548
150
240
385
610
970
1367
1139
949
680
__
455
341
__
__
__
1811
__
__
1509
__
__
1085
1729
__
__
__
__
724
1152
1832
543
864
1374
15
14
23
36
57
91
56
92
144
228
364
100
160
255
405
650
227
362
576
916
11
10
17
27
43
68
40
68
108
172
272
75
120
192
305
485
170
9
8
14
21
34
55
32
52
84
136
220
60
96
154
240
390
136
__
__
11
18
28
45
26
__
113
108
172
274
7792
__
__
3896
__
__
1945
1300
977
__
__
12367
19705
__
__
__
__
6193
9852
__
__
__
__
3093
4820
2067
3289
1553
2471
720
1238
650
1033
60159
__
31327
__
__
15663
__
__
7822
5229
3929
1970
1644
608
966
1538
3132
2614
2445
25
30
35
50
60
75
100
150
200
250
300
400
30
47
75
21
32
54
18
28
45
15
24
39
11
17
27
9
14
22
8
11
18
6
9
14
4
6
9
__
__
7
__
__
__
__
__
__
__
__
__
10
8
6
4
10
8
6
4
12
10
32V
8
6
4
68
181
288
458
__
23787
37810
18
41
65
110
12
24V
42
63
100
163
260
217
345
549
14964
10
8
6
13
12
10
8
12
12V
21
34
54
85
100
50
80
128
200
271
432
687
12
12
48V
120V
10
8
6
165
165
260
415
660
1050
660
120
110
190
300
475
760
440
1040
1668
2640
760
1200
1900
4200
3040
1160
__
840
1340
__
__
__
__
__
__
__
1899
__
__
__
__
__
__
86
85
136
215
340
540
340
71
71
112
180
285
455
284
62
43
61
42
97
154
68
108
245
390
170
275
244
168
544
860
1360
448
720
1140
388
616
980
272
432
680
2160
1810
1560
1100
36
35
52
90
140
225
140
208
360
560
900
29
29
45
72
114
182
116
180
288
456
500
800
435
690
300
480
1280
__
1110
1740
770
1220
640
1020
510
815
__
1620
1300
__
__
__
250
400
728
600
960
1540
__
200
320
22
21
34
54
86
137
84
136
216
344
548
150
240
385
610
970
1367
1139
949
680
__
455
341
__
__
__
1811
__
__
1509
__
__
1085
1729
__
__
__
__
724
1152
1832
543
864
1374
• Reduces required battery capacity by 75%, providing
necessary illumination with fewer remote heads and
battery units for project cost savings.
15
14
23
36
57
91
56
92
144
228
364
100
160
255
405
650
227
362
576
916
11
10
17
27
43
68
40
68
108
172
272
75
120
192
305
485
170
9
8
14
21
34
55
32
52
84
136
220
60
96
154
240
390
136
__
__
11
18
28
45
26
113
__
__
3896
__
__
1945
1300
977
12367
19705
__
__
__
__
6193
9852
__
__
__
__
3093
4820
2067
3289
1553
2471
720
1238
650
1033
60159
__
31327
__
__
15663
__
__
7822
5229
3929
1970
1644
608
966
1538
3132
2614
2445
Keeping pace with technology, in 2012 we introduced a
12V-5W MR16 LED lamp. With a typical luminous flux of 340
lumens, this lamp has the same lighting performance as
a 20W high-output halogen MR16. A twin emergency head
installed at a height of 7.5ft illuminates more than a 70ft
path of egress.
510-LUMEN 6W MR16 LED
New in Fall 2013, we intoduce a 12V - 6W MR16 LED lamp,
which offer typical luminous flux of 510 lumens. Like the
lower wattage MR16 LED lamps, this new lamp is specially
designed for emergency lighting. It offers the same lighting
preformance as the 35W or 20W Mr16 IR. A twin emergency
head installed at a height of 7.5’ illuminates approximately
100’ path of egress.
Compared to halogen lamps (16-20W), these 4W MR16
LED lamps illuminate the same area of egress during an
emergency situation by using 75% less power. This has
a direct impact on the battery size, reducing the back-up
capacity needs by 75%. Consequently, it also reduces the
total cost of the application, with the use of smaller battery
capacity units, the possibility of using fewer fixtures due to
superior illumination, thus also reducing electrical wiring,
and it it reduces the environmental footprint.
68
108
172
274
7792
__
__
340-LUMEN 5W MR16 LED
200-LUMEN 4W MR16 LED
Leading the technology trend, Emergi-Lite® offers a
complete series of 4W MR16 LED lamps available for all
the standard battery voltages: 6V, 12V, 24V and 120V. With
up to 30,000 hours of operational life and a luminous
flux of typically 200 lumens, they are available with most
emergency heads designed to hold an MR16 lamp and meet
the majority of illumination specifications. For example: one
pair of LED emergency heads installed at a height of 7.5ft,
illuminates a 6ft by 40ft path of egress.
21
42
63
100
163
260
181
288
458
__
23787
37810
• Ideal for indoor and outdoor use.
• = lower lamp temperature (80 - 120°C) is a huge benefit
for lighting in hazardous locations.
__
__
__
__
__
34
54
85
100
50
80
128
200
325
217
345
549
14964
10
8
6
• Vibration-resistant LED stands up to industrial
environments.
• = operational life: 30,000+ hours, equivalent to a lifetime
warranty in emergency lighting.
__
44
72
112
180
271
432
687
12
• Small profile, compact white lighting is ideal for
architectural applications.
• = lamp efficacy: 50 - 70 lumen per watt compared to 15 30 lumen per watt of the best halogen lamp.
WATTS
WIRE
SIZE
6
__
__
__
__
__
44
72
112
180
325
6V
MR16 LED LAMP BENEFITS
• CSA C22.2 No. 141 certified.
• Energy-efficient LED MR16 lamp provides equivalent
lighting performance to a much higher watt halogen
MR16 lamp.
Extremely efficient and long-lasting, LED lamps become the
natural alternative to incandescent lamps due to three main
advantages:
LENGTH OF WIRE RUN (in feet)
WATTS
WIRE
SIZE
6
__
__
__
__
__
44
72
112
180
325
6V
MR16 LED ILLUMINATION
With the remarkable technology development in the last
decade, the light-emitting diode (LED) is becoming the
preferred solution in low- and medium-power lighting
applications. The emergency lighting industry is no
exception: today virtually every new product introduced to
market includes “white” LEDs for emergency illumination.
E= Line Voltage
22= Constant
.05= Factor for max. allowable
voltage drop
70-FT. PATH OF EGRESS 2 X 5W MR16 LED
40-FT. PATH OF EGRESS 2 X 4W MR16 LED
6
188
188
188
70-FT. PATH OF EGRESS 2 X 5W MR16 LED
6
WIRE SIZE GUIDE
BATTERY UNIT
CAPACITY CHART
ELECTRICAL CODE
BUILDING CODE
FIRE &
GENERATOR ROOM
LIMITED WARRANTY
PRODUCT INDEX
P. 198
P. 199
P. 200-201
P. 202-205
P. 200
P. 207
P. 208
161
197
Project/Location:
Contractor:
Wire Size Guide
Date:
Prepared by:
When remote fixtures and exit signs are connected to emergency lighting units of less than 50 volts, circuit runs must
be sufficient size to maintain a proper operating voltage to all lamps. The maximum allowable voltage drop should not
exceed 5%. Proper wire size can be selected from the following table or by use of the following formula:
CM= Wire size in circular mills
W= Emergency load in watts
L= Length of circuit in feet
CM = 22 X W X2 L
.05 X E
E= Line Voltage
22= Constant
.05= Factor for max. allowable
voltage drop
LENGTH OF WIRE RUN (in feet)
WATTS
WIRE
SIZE
13
18
25
30
35
50
60
75
100
150
200
250
300
400
6V
12
10
8
6
41
65
110
165
30
47
75
120
21
32
54
86
18
28
45
71
15
24
39
62
11
17
27
43
9
14
22
36
8
11
18
29
6
9
14
22
4
6
9
15
__
__
7
11
__
__
__
9
__
__
__
__
__
__
__
__
12V
12
10
8
6
4
165
260
415
660
1050
110
190
300
475
760
85
136
215
340
540
71
112
180
285
455
61
97
154
245
390
42
68
108
170
275
35
52
90
140
225
29
45
72
114
182
21
34
54
86
137
14
23
36
57
91
10
17
27
43
68
8
14
21
34
55
__
11
18
28
45
__
__
__
__
__
24V
12
10
8
6
4
660
1040
1668
2640
4200
440
760
1200
1900
3040
340
544
860
1360
2160
284
448
720
1140
1810
244
388
616
980
1560
168
272
432
680
1100
140
208
360
560
900
116
180
288
456
728
84
136
216
344
548
56
92
144
228
364
40
68
108
172
272
32
52
84
136
220
26
44
72
112
180
21
34
54
85
100
32V
12
10
8
6
4
1160
__
__
__
__
840
1340
__
__
__
600
960
1540
__
__
500
800
1280
__
__
435
690
1110
1740
__
300
480
770
1220
__
250
400
640
1020
1620
200
320
510
815
1300
150
240
385
610
970
100
160
255
405
650
75
120
192
305
485
60
96
154
240
390
50
80
128
200
325
42
63
100
163
260
48V
12
10
8
6
__
__
__
__
1899
__
__
__
1367
__
__
__
1139
1811
__
__
949
1509
__
__
680
1085
1729
__
__
__
__
__
455
724
1152
1832
341
543
864
1374
227
362
576
916
170
271
432
687
136
217
345
549
113
181
288
458
68
108
172
274
120V
12
10
8
6
14964
23787
37810
60159
__
__
__
__
7792
12367
19705
31327
__
__
__
__
__
__
__
__
3896
6193
9852
15663
__
__
__
__
__
__
__
__
1945
3093
4820
7822
1300
2067
3289
5229
977
1553
2471
3929
720
1238
1970
3132
650
1033
1644
2614
608
966
1538
2445
198
Project/Location:
Contractor:
Battery Unit Capacity Chart
Date:
Prepared by:
BATTERY UNIT
WATTAGE CAPACITY
ESL
30MIN
1H00
1H30
2H00
4H00
6V - 36W
36
21
15
12
6
6V - 72W
72
42
30
24
12
6V - 108W
108
63
45
36
18
6V - 180W
180
105
75
60
30
12V - 36W
36
21
15
12
6
12V - 72W
72
42
30
24
12
12V - 100W
100
58
42
33
17
12V - 144W
144
84
60
48
24
12V - 200W
200
117
83
67
33
12V - 250W
250
144
100
83
42
12V - 288W
288
168
120
96
48
12V - 360W
360
210
150
120
60
24V - 144W
144
84
60
48
24
24V - 200W
200
117
83
67
33
24V - 288W
288
168
120
96
48
24V - 350W
350
200
144
120
60
24V - 432W
432
250
180
144
72
24V - 550W
550
320
230
180
90
ESLT
ESLPK
199
RETRACT-A-LITE
DEL
Project/Location:
Contractor:
Electrical Code
Date:
Extracts from the Canadian
Electrical Code 2010
Prepared by:
SECTION 46 — EMERGENCY POWER
SUPPLY, UNIT EQUIPMENT, EXIT SIGNS,
AND LIFE SAFETY SYSTEMS
46-106 ARRANGEMENT OF LAMPS
46-000 SCOPE (SEE APPENDIX B)
1
This Section applies to the installation, operation, and maintenance of
(a) emergency power supply and unit equipment intended to provide
power to life safety systems; and
(b) emergency power supply and unit equipment intended to
provide illumination of exit signs, in theevent of failure of the
normal supply, where the emergency power supply is required
by the National Building Code of Canada.
2
This Section applies to the wiring between the emergency power supply
and life safety systems that are required by the National Building Code
of Canada to be provided with an emergency power supply
3
This Section applies to the wiring of exit signs
4
The requirements of this Section supplement or amend the general
requirements of this Code
1
Emergency lights shall be arranged so that the failure of any one lamp
will not leave in total darkness the area normally illuminated by it.
2
No appliance or lamp, other than those required for emergency
purposes, shall be supplied by the
emergency circuits.
46-108 WIRING METHOD (SEE APPENDICES
B AND G)
46-002 SPECIAL TERMINOLOGY (SEE APPENDIX B)
1
Except as permitted by Subrule (3), Rule 46-304(3), and Rule 46-400(2),
the following conductors shall be installed in accordance with Subrule
(2):
(a) conductors required for operation of life safety systems and
installed between an emergency power supply and life safety
systems;
(b) conductors between an emergency power supply and exit signs;
and
(c) conductors between unit equipment and remote lamps.
2
Conductors described in Subrule (1) shall be
(a) installed in metal raceway of the totally enclosed type;
(b) incorporated in a cable having a metal armour or sheath;
(c) installed in rigid non-metallic conduit; or
(d) installed in electrical non-metallic tubing where embedded in at
least 50 mm of masonry or poured concrete.
3
Not with standing Subrule (2), conductors installed in buildings of
combustible construction in accordance with Rules 12-506 to 12-520
shall be permitted to be
(a) run as a non-metallic-sheathed cable; or
(b) installed in a totally enclosed non-metallic raceway.
4
Conductors installed in accordance with Subrule (1) shall be kept entirely
independent of all other conductors and equipment and shall not enter
a luminaire, raceway, box, cabinet, or unit equipment occupied by other
conductors except where necessary
(a) in transfer switches; and
(b) in exit signs and emergency lights supplied from two sources.
5
Conductors between an emergency power supply and any electrical
equipment that is not defined as a “life safety system” in accordance
with this Section shall not enter a luminaire, raceway, box, or cabinet
occupied by conductors installed as described in Subrule (1), except
where necessary in busways, splitters, and other similar enclosures
provided for connection to the overcurrent device for an emergency
power supply described in Rule 46-208(1).
In this Section, the following definitions apply:
Emergency power supply
Emergency power, supplied by a generator, batteries, or a combination
there of, that is required by the National Building Code of Canada.
Life safety systems
Emergency lighting and fire alarm systems that are required to be
provided with anemergency power supply from batteries, generators,
or a combination thereof, and electrical equipment for building services
such as fire pumps, elevators, smoke-venting fans, smoke control fans,
and dampers that are required to be provided with an emergency power
supply by an emergency generator in conformance with the National
Building Code of Canada.
Unit equipment
Unit equipment for emergency lighting conforming to CSA C22.2 No. 141.
GENERAL
46-100 CAPACITY
Emergency power supply and unit equipment shall have adequate capacity and
rating to ensure the satisfactory operation of all connected equipment when
the principal source of power fails.
46-102 INSTRUCTIONS
1
Complete instructions for the operation and care of an emergency power
supply or unit equipment that
shall specify testing at least once every month to ensure security of
operation shall be posted on the
premises in a frame under glass.
2
The form of instructions and their locations shall be in compliance with
the National Building Code of
Canada.
EMERGENCY POWER SUPPLY
46-200 EMERGENCY POWER SUPPLY (SEE
APPENDIX B)
Rules 46-202 to 46-212 apply only to emergency power supply from central
standby power sources.
46-202 TYPES OF EMERGENCY POWER SUPPLY
(SEE APPENDIX G)
46-104 MAINTENANCE
Where batteries are used as a source of the emergency power supply, the
batteries shall be kept
1
The emergency power supply shall be a standby supply consisting of
(a) a storage battery of the rechargeable type having sufficient capacity
to supply and maintain at not less than 91% of full voltage the total
load of the emergency circuits for the time period required by the
National Building Code of Canada, but in no case less than 30 min,
and equipped with a charging means to maintain the battery in a
charged condition automatically; or
(b) a generator.
2
Automobile batteries and lead batteries not of the enclosed glass-jar
type are not considered suitable under Subrule (1) and shall be used
only where a deviation has been allowed in accordance with Rule 2-030.
(a) in proper condition; and
(b) fully charged at all times
200
Project/Location:
Contractor:
Electrical Code
Date:
Extracts from the Canadian
Electrical Code 2010
Prepared by:
3
46-304 SUPPLY CONNECTIONS
Where a generator is used, it shall be
(a) of sufficient capacity to carry the load;
(b) arranged to start automatically without failure and without undue
delay upon the failure of the normal power supply to any transfer
switch connected to this generator; and
(c) in conformance with CSA C282.
Each unit equipment shall be mounted with the bottom of the enclosure not
less than 2 m above the floor, wherever practicable.
1
Receptacles to which unit equipment is to be connected shall be not less
than 2.5 m above the floor, where practicable, and shall be not more than
1.5 m from the location of the unit equipment.
2
All power, control, and communication conductors between an emergency
generator as described in Rule 46-202(3), and electrical equipment required to
be installed as a part of the emergency power supply and located outside the
generator room shall be protected against fire exposure to provide continued
operation in compliance with the National Building Code of Canada.
Unit equipment shall be permanently connected to the supply if
(a) the voltage rating exceeds 250 V; or
(b) the marked input rating exceeds 24 A.
3
Where the ratings in Subrule (2) are not exceeded, the unit equipment
shall be permitted to be connected using the flexible cord and attachment
plug supplied with the equipment.
46-206 CONTROL
4
Unit equipment shall be installed in such a manner that it will be
automatically actuated upon failure of the power supply to the normal
lighting in the area covered by that unit equipment.
46-204 PROTECTION OF ELECTRICAL
CONDUCTORS (SEE APPENDICES B AND G)
1
2
An emergency power supply shall be controlled by automatic transfer
equipment that actuates the emergency power supply upon failure of the
normal current supply and that is accessible only to authorized persons.
46-306 REMOTE LAMPS (SEE APPENDIX B)
An automatic light-actuated device, approved for the purpose, shall be
permitted to be used to control separately the lights located in an area
that is adequately illuminated during daylight hours without the need
for artificial lighting.
46-208 OVERCURRENT PROTECTION
1
2
The overcurrent device for an emergency power supply shall be
coordinated with the overcurrent devices of feeders and branch circuits
supplying life safety systems and other electrical equipment connected
to the emergency power supply in order to provide selective operation of
the branch circuit overcurrent device when a fault occurs in that branch
circuit.
The branch circuit overcurrent devices shall be accessible only to
authorized persons.
2
The size of circuit conductors to remote lamps shall be such that the
voltage drop does not exceed 5% of the marked output voltage of the
unit equipment, or such other voltage drop for which the performance
of unit equipment is certified when connected to the specific remote
lamp being installed.
2
Remote lamps shall be suitable for remote connection and shall be
included in the list of lamps provided with the unit equipment.
3
The number of lamps connected to a single unit equipment shall not
result in a load in excess of the watts output rating marked on the
equipment for the emergency period required by the National Building
Code of Canada, and the load shall be computed from the information
in the list of lamps referred to in Subrule (2).
EXIT SIGNS
46-210 AUDIBLE AND VISUAL TROUBLE-SIGNAL
DEVICES
1
1
46-400 EXIT SIGNS (SEE APPENDICES B AND G)
Every emergency power supply shall be equipped with audible and visual
trouble-signal devices that warn of derangement of the current source
or sources and that indicate when exit signs or life safety systems are
supplied from the emergency power supply.
Audible trouble signals shall be permitted to be wired so that (a) they can
be silenced, but a red warning or trouble light shall continue to provide
the protective function; and
(b) when the system is restored to normal, the audible signal will
(i) sound, indicating the need to restore the silencing switch to its
normal position; or
(ii) reset automatically so as to provide sound for any subsequent
operation of the emergency power supply.
46-212 REMOTE LAMPS
Lamps shall be permitted to be mounted at some distance from the current
supply that feeds them, but the voltage drop in the wiring feeding such lamps
shall not exceed 5% of the applied voltage.
UNIT EQUIPMENT
46-300 UNIT EQUIPMENT (SEE APPENDIX B)
Rules 46-302 to 46-306 apply to individual unit equipment for emergency lighting
only.
46-302 MOUNTING OF EQUIPMENT
Each unit equipment shall be mounted with the bottom of the enclosure not
less than 2 m above the floor, wherever practicable.
201
1
Where exit signs are connected to an electrical circuit, that circuit shall
be used for no other purpose.
2
Notwithstanding Subrule (1), exit signs shall be permitted to be
connected to a circuit supplying emergency lighting in the area where
these exit signs are installed.
3
Exit signs in Subrules (1) and (2) shall be illuminated by an emergency
power supply where emergency lighting is required by the National
Building Code of Canada.
Project/Location:
Contractor:
Building Code
Date:
Extracts from the National Building
Code of Canada 2010
Prepared by:
3.2.6. ADDITIONAL REQUIREMENTS FOR
HIGH BUILDINGS (SEE APPENDIX B.)
3.2.7.4. EMERGENCY POWER FOR LIGHTING
3.2.6.1. APPLICATION
1
This Subsection applies to a building
a) of Group A, D, E or F major occupancy classification that is more
than
i) 36 m high, measured between grade and the floor level of the
top storey, or
ii) 18 m high, measured between grade and the floor level of the
top storey, and in which the cumulative or total occupant load
on or above any storey above grade, other than the first storey,
divided by 1.8 times the width in metres of all exit stairs at that
storey, exceeds 300,
b) containing a Group B major occupancy in which the floor level
of the highest storey of that major occupancy is more than 18 m
above grade,
c) containing a floor area or part of a floor area located above the
third storey designed or intended as a Group B, Division 2 or 3
occupancy, or
d) containing a Group C major occupancy whose floor level is more
than 18 m above grade.
Emergency lighting to provide an average level of illumination of not less
than 10 lx at floor or catwalk level shall be included in a service space
referred to in Sentence 3.2.1.1.(8).
3
The minimum value of the illumination required by Sentences (1) and
(2) shall be not less than 1 lx.
4
In addition to the requirements of Sentences (1) to (3), the installation of
battery-operated emergency lighting in buildings or part thereof where
treatment is provided shall conform to the appropriate requirements of
CSA Z32, “Electrical Safety and Essential Electrical Systems in Health
Care Facilities”.
2
If self-contained emergency lighting units are used, they shall conform
to CSA C22.2 No. 141, “Emergency Lighting Equipment.”
1
Except as required by Articles 3.2.7.6. and 3.2.7.7., an emergency
electrical power supply system shall be installed in conformance with
CAN/CSA-C282, “Emergency Electrical Power Supply for Buildings.”
(See Sentence 3.2.7.8.(1) for emergency electrical power supply for voice
communication systems).
3.4.5. EXIT SIGNS
Emergency lighting shall be provided to an average level of illumination
not less than 10 lx at floor or tread level in
a) exits
b) principal routes providing access to exit in open floor areas and in
service rooms,
c) corridors used by the public,
d) corridors serving sleeping rooms in a treatment occupancy,
e) corridors serving sleeping rooms in a care occupancy, except
corridors serving sleeping rooms within individual suites of care
occupancy,
f) corridors serving classrooms,
g) underground walkways,
h) public corridors,
i) floor areas or parts thereof where the public may congregate
i) in Group A, Division 1 occupancies, or
ii) in Group A, Division 2 and 3 occupancies having an occupant load
of 60 or more,
j) floor areas or parts thereof of daycare centreswhere persons are
cared for, and
k) food preparation areas in commercial kitchens.
2
An emergency power supply shall be
a) p rovided to maintain the emergency lighting required by this
Subsection from a power source such as batteries or generators
that will continue to supply power in the event that the regular
power supply to the building is interrupted, and
b) so designed and installed that upon failure of the regular power it
will assume the electrical load automatically for a period of
i) 2 h for a building within the scope of Subsection 3.2.6.,
ii) 1 h for a building of Group B major occupancy classification that
is not within the scope of Subsection 3.2.6., and
iii) 30 min for a building of any other occupancy. (See Appendix A.)
3.2.7.5. EMERGENCY POWER SUPPLY
INSTALLATION
3.2.7.3. EMERGENCY LIGHTING
1
1
3.4.5.1. EXIT SIGNS
1
2
3
4
5
202
Every exit door shall have an exit sign placed over or adjacent to it if
the exit
serves
a) a building more than 2 storeys in building height,
b) a building having an occupant load of more than 150, or
c) a room or floor area that has a fire escape as part of a required
means of egress
Every exit sign shall
a) be visible on approach to the exit,
b) except as permitted in Sentence (3), consist of a green pictogram
and a white or lightly tinted graphical symbol meeting the colour
specifications referred to in ISO 3
864-1, “Graphical symbols – Safety colours and safety
signs – Part 1: Design principles for safety signs in workplaces
and public areas,” and
c) conform to the dimensions indicated in ISO 7010, “Graphical
symbols – Safety colours and safety signs – Safety signs used
in workplaces and public areas,” for the following symbols (see
Appendix A):
i) E001 emergency exit left,
ii) E002 emergency exit right,
iii) E005 90-degree directional arrow, and
iv) E006 45-degree directional arrow
Internally illuminated exit signs shall be continuously illuminated and
a) where illumination of the sign is powered by an electrical
circuit, be constructed in conformance with CSA C22.2 No. 141,
“Emergency Lighting Equipment,” or
b) where illumination of the sign is not powered by an electrical
circuit, be constructed in conformance with CAN/ULC-S572,
“Photoluminescent and Self-Luminous Signs and Path Marking
Systems.”
Externally illuminated exit signs shall be continuously illuminated
and be constructed in conformance with CAN/ULC-S572,
“Photoluminescent and Self-Luminous Signs and Path Marking
Systems.” (See Appendix A.)
he circuitry serving lighting for externally and internally illuminated
T
exit signs shall
a) serve no equipment other than emergency equipment, and
b) be connected to an emergency power supply as described in
Article 3.2.7.4.
Project/Location:
Contractor:
Building Code
Date:
Extracts from the National Building Code of
Prepared by:
Canada 2010
6
here no exit is visible from a public corridor, from a corridor used by
W
the public in a Group A or B major occupancy, or from principal routes
serving an open floor area having an occupant load of more than 150,
an exit sign conforming to Clauses (2)(b) and (c) with an arrow or
pointer indicating the direction of egress shall be provided.
5
The circuitry serving lighting for externally and internally illuminated
exit signs shall
a) serve no equipment other than emergency equipment, and
b) b e connected to an emergency power supply as described in
Sentences 9.9.12.3.(2), (3) and (7).
7
Except for egress doorways described in Sentence 3.3.2.4.(4), an
exit sign conforming to Sentences (2) to (5) shall be placed over or
adjacent to every egress doorway from rooms with an occupant load of
more than 60 in Group A, Division 1 occupancies, dance halls, licensed
beverage establishments, and other similar occupancies that, when
occupied, have lighting levels below that which would provide easy
identification of the egress doorway.
6
Where no exit is visible from a public corridor, from a corridor used by
the public, or from principal routes serving an open floor area having
an occupant load of more than 150, an exit sign conforming to Clauses
(2)(b) and (c) with an arrow or pointer indicating the direction of egress
shall be provided
9.9.11.4. SIGNS FOR STAIRS AND RAMPS AT EXIT
LEVEL
3.4.5.2. SIGNS FOR STAIRS AND RAMPS AT EXIT
LEVEL
1
1
In a building more than 2 storeys in building height, any part of an exit
ramp or stairway that continues up or down past the lowest exit level
shall have a posted sign clearly indicating that it does not lead to an exit.
9.9.12. LIGHTING
9.9.11. SIGNS
9.9.11.4. SIGNS FOR STAIRS AND RAMPS AT EXIT
LEVEL
9.9.11.1. APPLICATION
1
This Subsection applies to all exits except those serving not more than
one dwelling unit or a house with a secondary suite.
1
9.9.11.2. VISIBILITY OF EXITS
1
2
3
4
This Subsection applies to the lighting of all means of egress except
those within dwelling units or a house with a secondary suite.
9.9.12.2. REQUIRED LIGHTING IN EGRESS
FACILITIES
Exits shall be located so as to be clearly visible or their locations shall
be clearly indicated.
9.9.11.3. EXIT SIGNS
1
In buildings that are 3 storeys in building height, any part of an exit ramp
or stairway that continues up or down past the lowest exit level shall be
clearly marked to indicate that it does not lead to an exit, if the portion
beyond the exit level may be mistaken as the direction of exit travel.
Every exit door shall have an exit sign placed over it or adjacent to it if the
exit serves
a) a building that is 3 storeys in building height,
b) a building having an occupant load of more than 150, or
c) a room or floor area that has a fire escape as part of a required
means of egress.
1
Every exit, public corridor or corridor providing access to exit for the
public shall be equipped to provide illumination to an average level of
not less than 50 lx at floor or tread level and at all points such as angles
and intersections at changes of level where there are stairs or ramps.
2
The minimum value of the illumination required by Sentence (1) shall
be not less than 10 lx
9.9.12.3. EMERGENCY LIGHTING
Every exit sign shall
a) be visible on approach to the exit,
b) except as permitted in Sentence (3), consist of a green pictogram
and a white or lightly tinted graphical symbol meeting the colour
specifications referred to in ISO 3864-1, “Graphical symbols –
Safety colours and safety signs – Part 1: Design principles for safety
signs in workplaces and public areas,” and
c) conform to the dimensions indicated in ISO 7010, “Graphical
symbols – Safety colours and safety signs – Safety signs used
in workplaces and public areas,” for the following symbols (see
A-3.4.5.1.(2)(c) in Appendix A):
i) E001 emergency exit left,
ii) E002 emergency exit right,
iii) E005 90-degree directional arrow, and
iv) E006 45-degree directional arrow.
Internally illuminated exit signs shall be continuously illuminated and
a) where illumination of the sign is powered by an electrical
circuit, be constructed in conformance with CSA C22.2 No. 141,
“Emergency Lighting Equipment,” or
b) where illumination of the sign is not powered by an electrical
circuit, be constructed in conformance with CAN/ULC-S572,
“Photoluminescent and Self-Luminous Signs and Path Marking
Systems.”
Externally illuminated exit signs shall be continuously illuminated and
be constructed in conformance with CAN/ULC-S572, “Photoluminescent
and Self-Luminous Signs and Path Marking Systems.” (See A-3.4.5.1.(4)
in Appendix A.)
203
1
Emergency lighting shall be provided in
a) exits,
b) principal routes providing access to exit in an open floor area,
c) corridors used by the public,
d) underground walkways, and
e) public corridors.
2
Emergency lighting required in Sentence (1) shall be provided from a
source of energy separate from the electrical supply for the building.
3
Lighting required in Sentence (1) shall be designed to be automatically
actuated for a period of at least 30 min when the electric lighting in the
affected area is interrupted.
4
Illumination from lighting required in Sentence (1) shall be provided to
average levels of not less than 10 lx at floor or tread level.
5
The minimum value of the illumination required by Sentence (4) shall be
not less than 1 lx.
6
Where incandescent lighting is provided, lighting equal to 1 W/m2 of
floor area shall be considered to meet the requirement in Sentence (4).
7
Where self-contained emergency lighting units are used, they shall
conform to CSA C22.2 No. 141, “Emergency Lighting Equipment.”
Project/Location:
Contractor:
Building Code
Date:
Extracts from the National Building
Code of Canada 2010
Prepared by:
APPENDIX A
EXPLONATORY MATERIAL
A-3.1.2. Use Classification
The purpose of classification is to determine which requirements apply.
This Code requires classification in accordance with every major occupancy for which the building is used or intended to be used. Where necessary, an application
clause has been inserted in this Part to explain how to choose between the alternative requirements which multiple occupancy classification may present.
A-3.1.2.1.(1) Major Occupancy Classification.
The following are examples of the major occupancy classifications described in Table 3.1.2.1.:
EXAMPLES
Motion picture theatres
Opera houses
Television studios admitting a viewing
audience
Theatres, including experimental theatres
Art galleries
Auditoria
Bowling alleys
Churches and similar places of worship
Clubs, nonresidential
Community halls
Courtrooms
Dance halls
Exhibition halls (other than classified in
Group E)
Gymnasia
Lecture halls
Libraries
Licensed beverage establishments
Museums
Passenger stations and depots
Recreational piers
Restaurants
Schools and colleges, nonresidential
Undertaking premises
Arenas
Indoor swimming pools, with or without
spectator seating
Rinks
GROUP
DIVISION
A
1
A
2
A
3
Amusement park structures (not elsewhere
classified)
Bleachers
Grandstands
Reviewing stands
Stadiums
A
4
Jails
Penitentiaries
Police stations with detention quarters
Prisons
Psychiatric hospitals with detention
quarters
Reformatories with detention quarters
B
1
Care facilities with treatment
Convalescent /recovery/rehabilitation
centres with treatment
Hospices with treatment
Hospitals
Infirmaries
Nursing homes with treatment
Psychiatric hospitals without detention
quarters
Respite centres with treatment
B
2
Assisted/supportive living facilities
Care facilities without treatment
Children’s custodial homes
Convalescent/recovery/rehabilitation
centres without treatment
Group homes
Hospices without treatment
Nursing homes without treatment
Reformatories without detention
quarters
Respite centres without treatment
B
3
Apartments
Boarding houses
Clubs, residential
Colleges, residential
Convents
Dormitories
Hotels
Houses
Lodging houses
Monasteries
Motels
Schools, residential
C
204
Project/Location:
Contractor:
Date:
Prepared by:
EXAMPLES
GROUP
DIVISION
Banks
Barber and hairdressing shops
Beauty parlours
Dental offices
Dry cleaning establishments, selfservice, not using flammable or explosive
solvents or cleaners
Laundries, self-service
Medical offices
Offices
Police stations without detention
quarters
Radio stations
Small tool and appliance rental and
service establishments
D
Department stores
Exhibition halls
Markets
Shops
Stores
Supermarkets
E
Bulk plants for flammable liquids
Bulk storage warehouses for hazardous
substances
Cereal mills
Chemical manufacturing or processing
plants
Distilleries
Dry cleaning plants
Feed mills
Flour mills
Grain elevators
Lacquer factories
Mattress factories
Paint, varnish and pyroxylin product
factories
Rubber processing plants
Spray painting operations
Waste paper processing plants
F
1
Aircraft hangars
Box factories
Candy plants
Cold storage plants
Dry cleaning establishments not using
flammable or explosive solvents or
cleaners
Electrical substations
Factories
Freight depots
Helicopter landing areas on roofs
Laboratories
Laundries, except self-service
Mattress factories
Planing mills
Printing plants
Repair garages
Salesrooms
Service stations
Storage rooms
Television studios not admitting a
viewing audience
Warehouses
Wholesale rooms
Woodworking factories
Workshops
F
2
Creameries
Factories
Laboratories
Light-aircraft hangars (storage only)
Power plants
Salesrooms
Sample display rooms
Storage garages, including open air
parking garages
Storage rooms
Warehouses
Workshops
F
3
A-3.4.5.1.(2)(C) GRAPHICAL SYMBOLS FOR EXIT
SIGNS
ISO 7010, “Graphical” symbols – Safety colours
and safety signs – Safety signs used in workplaces and public areas,” identifies
the following internationally recognized symbols for use at required exits
“EMERGENCY EXIT RIGHT” (E001) SYMBOL FROM ISO
7010
Figure A-3.4.5.1.(2)(c)-B
90-degree directional arrow (E005) from ISO 7010
A-3.4.5.1.(4) Externally Illuminated Signs
An external lighting source is required to properly charge photoluminescent signs.
These types of signs must be lit in conformance with the charging requirements
stated in CAN/ULC-S572.
A-3.4.6. Application to Means of Egress
The requirements in Subsection 3.4.6. apply to interior and exterior exits, as well
as to ramps, stairways and passageways used by the public as access to exit.
The treads, risers, landings, handrails and guards for the latter access to exit
facilities must thus be provided in conformance with the appropriate requirements
for exit facilities.
205
Project/Location:
Contractor:
Fire Code
Generator Room
Extracts from the National Fire
Code of Canada 2010
Extracts from the Canadian Standards
Prepared by:
Association 2010
Date:
2.7. SAFETY TO LIFE
SECTION 6.11
2.7.3. EXIT LIGHTING, EXIT SIGNS AND
EMERGENCY LIGHTING
EMERGENCY LIGHTING
6.11.1
2.7.3.1. INSTALLATION AND MAINTENANCE
The emergency electrical power supply room and the automatic
transfer switch room, where separate, shall be equipped with unit
equipment for emergency lighting that complies with CSA C22.2 No.
141. Sufficient lamps shall be provided to ensure that a minimum
lighting level of 50 lx for 2 h is available at all equipment locations
requiring adjustment or service.
1) Exit lighting, exit signs and emergency lighting shall be provided in
buildings in conformance with the NBC. (See Appendix A.)
2) Exit lighting and exit signs shall be illuminated during times when
the building is occupied.
3) Emergency lighting shall be maintained in operating condition, in
conformance with Section 6.5.
Note: This illumination level is significantly greater than that specified
in the NBCC, which requires 10 lx for egress route emergency lighting
6.5. EMERGENCY POWER SYSTEMS AND
UNIT EQUIPMENT FOR EMERGENCY
LIGHTING
6.11.2
Emergency lighting units shall be tested in accordance with Table 2
and CSA C22.2 No. 141.
6.5.1.1. INSPECTION, TESTING AND MAINTENANCE
6.11.3
1) Except as provided in Articles 6.5.1.2. to 6.5.1.5., emergency power
systems shall be inspected, tested and maintained in conformance
with CAN/CSA-C282, “Emergency Electrical Power Supply for
Buildings.”
2) A n emergency electrical power supply system for emergency
equipment for health care facilities shall be inspected, tested
and maintained in conformance with CSA Z32, “Electrical Safety
and Essential Electrical Systems in Health Care Facilities.” (See
Appendix A.)
The emergency lighting unit shall include
(a) automatic self-diagnostic circuitry; and
(b) a transient voltage surge suppressor on the supply side of power
to the unit.
6.5.1.2. NOTIFICATION
1) When an emergency power system or any part thereof is shut down,
the supervisory staff shall be notified in conformance with Section
2.8.
6.5.1.3. INSTRUCTIONS
1) Where an emergency power system is installed, instructions shall
be provided for switching on essential loads and for starting the
generator when this is not done automatically.
6.5.1.4. RECORDS
1) Written records shall be maintained as required in CAN/CSA-C282,
“Emergency Electrical Power Supply for Buildings”.
6.5.1.6. INSPECTION OF UNIT EQUIPMENT
1) S elf-contained emergency lighting unit equipment shall be
inspected at intervals not greater than one month to ensure that
a) p ilot lights are functioning and not obviously damaged or
obstructed,
b) t he terminal connections are clean, free of corrosion and
lubricated when necessary,
c) the terminal clamps are clean and tight as per manufacturer’s
specifications, and
d) the battery surface is kept clean and dry.
2) Self-contained emergency lighting unit equipment shall be tested
a) a t intervals not greater than one month to ensure that the
emergency lights will function upon failure of the primary power
supply, and
b) a t intervals not greater than 12 months to ensure that the
unit will provide emergency lighting for a duration equal to
the design criterion under simulated power failure conditions.
3) After completion of the test required in Clause (2)(b), the charging
conditions for voltage and current and the recovery period shall
be tested to ensure that the charging system is functioning in
accordance with the manufacturer’s specifications.
206
Project/Location:
Contractor:
Date:
Limited Warranty
Prepared by:
WARRANTY
1.1
Emergi-Lite® emergency lighting equipment units (excluding AC and
DC Central Systems, lamps, pilot lights and fuses) are fully warranted
to be free of defects in material and workmanship under normal use
for a period of one (1) year. Emergi-Lite® emergency lighting equipment
units with the NEXUS® option are fully warranted to be free of defects
in material and workmanship under normal use for a period of five (5)
years. The full warranty period begins on the date of installation or
ninety (90) days from the date of shipment, whichever date is earlier.
3.4
If new replacement parts are shipped before defective goods are
received for evaluation, the replacement parts will be invoiced at the net
price in effect at the time. These charges will be credited if, upon receipt
and evaluation of goods, a defect is determined. Only replacement
parts will be shipped under these circumstances, if field replacement
is possible. Emergi-Lite® factory only reserves the right to ship new unit
equipment for replacement purposes. Unit returned after installation
cannot be restored to 100% saleable condition.
1.2
DC and AC Central Systems are covered by a separate comprehensive
warranty.
4.1
1.3
LED strips used in Emergi-Lite® Exit signs are warranted to be free of
defects in material and workmanship under normal use for a period of
ten (10) years. The full warranty period begins on the date of installation
or ninety (90) days from the date of shipment, whichever date is earlier.
In no event shall Emergi-Lite® be liable for back charges of any kind,
including without limitation, labor charges for field repair or late
penalties.
4.2
1.4
Emergi-Lite® unit equipment batteries are warranted to be free of
defects in material and workmanship under normal use for a period
of one (1) year full and nine (9) years Pro Rata. The full warranty period
begins on the date of installation or ninety (90) days from the date of
shipment, whichever date is earlier. Batteries have a maximum storage
life (shelf life) of 6 months. Batteries must be recharged or placed in
service within the 6 months storage life or battery warranty will be void.
This warranty does not cover damages caused by abuse, improper
maintenance or installation or damage due to installation areas with
other than normal temperatures and environmental conditions per
application specifications. Emergi-Lite® assumes no responsibility
for any damages to people, property, apparatus or otherwise resulting
from improper installation or maintenance of its emergency lighting
unit equipment.
4.3
This warranty does not cover damages caused by abuse, fire or act
of God.
4.4
In no event shall Emergi-Lite® be liable for incidental or consequential
damages.
4.5
The foregoing warranty is in lieu of other warranties, expressed or
implied. Except as stated in this warranty, Emergi-Lite ® shall not be
liable for any defects in, or breach of any contract relating to, the quality
of performance of Emergi-Lite® equipment under any theory of law
including, without limitation, contract, negligence, strict liability or
misrepresentation.
4.6
Emergi-Lite ® warranty coverage shall not apply to any equipment
of another manufacturer used in conjunction with Emergi-Lite ®
equipment.
5.1
Defective goods returned to the factory must be shipped prepaid. Any
and all collect returned shipments will be refused. Freight charges
to return repaired equipment or ship replacement equipment to the
purchaser to be paid by Emergi-Lite®. Factory will return repaired or
replacement goods via same shipping method as received whenever
possible and practical.
2.1
Should defect appear in the equipment or batteries listed in the
paragraph 1.1, 1.2, 1.3 or 1.4 above within the specified full warranty
period, Emergi-Lite ® will repaid or replace equipment without
charge (see paragraph 3.4). Such repair or replacement shall be the
purchaser’s exclusive remedy.
2.2
The Pro Rata Warranty period for batteries begins on the date the full
warranty ends.
2.3
A battery determined to be defective during the Pro Rata Warranty
Period shall be repaired or replaced at a cost equal to the net price in
effect at the time, reduced by the percentage obtained in multiplying
10% by the number of full years remaining in the total warranty
period. Such repair or replacement at this adjusted price shall be the
purchaser’s exclusive remedy.
3.1
All warranties are subject to proper installation and maintenance in
accordance with the instructions supplied.
3.2
Any material deemed defective must be returned freight prepaid, to
a service depot for evaluation (see paragraph 5.1). Any changes in
circuitry or components by other than an authorized Emergi-Lite®
personnel or its service companies will void the warranty.
3.3
All warranties are limited to the repair and/or replacement of parts
or equipment, which, upon examination at our service depot, are
determined to be defective and in our judgment are subject to repair
or replacement under warranty. Replacement of lamps, pilot lights, and
fuses is not included in the warranty.
207
Project/Location:
Contractor:
PRODUCT INDEX
Date:
Prepared by:
NAME
SERIES PG
NAME
SERIES PG
NAME
SERIES PG
NAME
SERIES PG
EDE
EDE
PremierTM Combo
PRE
ESLT
06ESLT
108-109
EF18
EF18
145
EF18D
145
EX30
EX3
16-17
56-57
18-19
C8SRPK
C8SRPK1
58
ESLT
12ESLT
108-109
EF18D
EAE
EAE
20
C8ESPK
C8SRPK2
59
ESLT
24ESLT
108-109
EF18T
EF18T
145
EX3
EX38
21
C8SRPK-P
C8SRPK
60-61
WP36
WP
110
DistinctionTM
EF150
146
EFR
DistinctionTM
EFR
147
EF39
EF39
148-149
EF25
EF25
150
EF26
EF26
151
EF26DS
EF26D
151
EF26D
EF26DS
151
EF11
EF11
152
EF11D
EF11D
152
EF11T
EF11T
152
EF30
EF30
153
EF30D
EF30D
153
EF30T
EF30T
153
EX3
EX39
21
EN
EN
62
Eclipse
ECL
111
C8SR3
C8SR38
22
LPEX600
LPEX60
63
JMLC
06JMLC
112-113
C8SR3
C8SR39
22
ENC
ENC
64
JMLC
12JMLC
112-113
EX3F
EX38F
23
LPEX600-N
LPEX60
65
JMLA
06JMLA
114
EX3F
EX39F
23
EH
EH
66
JMLA
12JMLA
114
C8SR35
C8SR36
24
LPEXHZ
LPEXHZ
67
JEM18P
JEM
115
C8SR35
C8SR36R
24
EHC
EHC
68-69
PremierTM
06PRE
116-117
C8SR35
C8SR37
24
EXHZ
EXHZ
70-71
PremierTM
12PRE
116-117
C8ES35 & C8SE35
C8ES
25
EX
EX
72-73
ESL
06ESL
118-119
C8ES35 & C8SE35
C8SE
25
LPEX-XP
LPEXXP
74-75
ESL
12ESL
118-119
C8E/S35R
C8ES
26
C8SRXP
C8SRXP1
76-77
ESL
24ESL
118-119
PRE
PRED
27
EXP
EXP
78-79
NXM
06NXM
120-121
LPEX100
LPEX
28
EXP
EXP
80-81
NXM
12NXM
120-121
LPSR100
LPSR
29
EX160
EX16
82
EF45Q
EF45Q
154
LPEX300
LPEX30
30
SR160
SR16
82
IPE
IPE
122
EF45DQ
EF45DQ
154
LPSR300
LPSR30
31
ET
ET
82
SIPE
SIPE
123
EF41
EF41
154
C8ES300
C8ES30
32
Retrofit Kits
SNAP II
84
ESLPK
06ESL
124-125
EFXPR
EFXPR
155
EA
EA
33
Retrofit Kits
SNAP III
85
ESLPK
12ESL
124-125
LPEX50
LPEX5
34
Retrofit Kits
SNAP I
85
ESLPK
24ESL
124-125
C8SR50
C8SR5
35
HZM
06HZM
126-127
LPEX
36
BULBI/
HB
86
LPEX
Retrofit Kits
HZM
12HZM
126-127
LPEX54
LPEX54
37
Retrofit Kits
BULBII/
HB
86
ESLNX
06ESL
128-129
ESLNX
12ESL
128-129
ESLNX
24ESL
128-129
48 & FPS
FPS800
130
TM
C8ES70 & C8SE70
C8
38
Pendant Kit
P1E
87
ES70B12
ES
39
Pendant Kit
P2E
87
40-41
Pendant Kit
P23E
87
P4E
87
48 & FPS
FPS1600
130
EAC
EAC
LPEX50-P
LPEX52
42
Pendant Kit
C8SR50-P
C8SR52
43
DEL Lux-Ray
LUX
98-99
48 & FPS
FPS3200
130
ES
ES
44
Retract-a-LiteTM
RTL
100
48 & FPS
FPS
130
EX10
EX10
45
101
DEL Lux-Ray
C8SR10
46
Mini
Retract-a-LiteTM
MR
C8SR10
C8ES10 & C8SE10
C8
47
ProviderTM
CPRO
102
ESC
ESC
48
DistinctionTM
EFR2
103
EX10-P
EX10
49
DistinctionTM
06ESL
104-105
SR
SR12
50-51
DistinctionTM
12ESL
12ESL-EX
12ESL
52
DistinctionTM
12ESL-SR
12ESL
53
EP
EP
Premier TM Exit
PRE
TM
LUX
138
EF40
EF40M
139
Retract-a-LiteTM
12RTLR
140
Retract-a-LiteTM
24RTLR
140
104-105
Mini
Retract-a-LiteTM
MR
141
24ESL
104-105
Literay™
EF33
142
DEL
06DEL
106-107
143
DEL
12DEL
106-107
EF9/EF9Q/
EF9M
EF9
54
55
DEL
24DEL
106-107
EF15
EF15
144
208
TM
www.emergi-lite.ca
All information and specifications contained in this catalogue are subject to change due to
engineer design, errors and omissions.
Illustrations and diagrams within this catalogue may vary from actual products.
© 2013 Thomas&Betts Limited. All rights reserved.
Printed in Canada.
2013/11/3000 Order No.: ELCAT-ENG
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement