Zanussi | ZERB 8643 | Specifications | Zanussi ZERB 8643 Specifications

ZANUSSI
FRIDGE - FREEZER
ZERB 8643
INSTRUCTION BOOK
GB
200370060
A/ZE/15. (05.)
This instruction book contains safety precautions, information on use and helpful hints and tips.
To ensure you use this appliance effectively and safely, please read this instruction book carefully
before installing or using it and retain for future reference.
The symbols below help you to find things more easily:
Safety precautions
Warnings and Safety information
Hints, useful information
Environmental information
The symbol on the product or on its packaging indicates that this product may not be treated as
household waste. Instead it shall be handed over to the applicable collection point for the recycling of
electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help
prevent potential negative consequences for the environment and human health, which could otherwise
be caused by inappropriate waste handling of this product. For more detailed information about recycling
of this product, please contact your local city office, your household waste disposal service or the shop
where you purchased the product.
2
IMPOR TANT S AFET Y INS TR UCTIONS
These warnings are provided in the interests of your safety. Ensure that you understand them all
before installing or using this appliance. Your safety is of paramount importance. If you are unsure
about any of the meanings or these warnings contact the Customer Care Department.
Prior to installation
Check the appliance for transport damage. Under no
circumstances should a damaged appliance be
installed. In the event of damage please contact your
retailer.
Installation
This appliance is heavy. Care should be taken when
moving it.
It is dangerous to alter the specifications or attempt to
modify this product in any way.
Ensure that the appliance does not stand on the
electrical supply cable. If the supply cable is damaged, it
must be replaced by a cable available from your local
Service Force Centre.
Make sure that the power plug has not been
squashed or damaged during transit.
- A damaged power plug may overheat and cause a fire.
As you unpack the appliance, check carefully for
any signs of transit damage.
Do not place heavy articles or the fridge/freezer
itself on the power cord.
- There is a risk of a short circuit and fire.
Do not remove the power cord by pulling on its lead,
particularly when the fridge/freezer is being pulled
out of its niche.
- Damage to the cord may cause a short-circuit, fire
and/or electric shock.
- If the power cord is damaged, it must be replaced by a
certified service agent or qualified service personnel.
If the power plug socket is loose, do not insert the
power plug.
- There is a risk of electric shock or fire.
Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.
Parts which heat up should not be exposed. Whenever
possible, the back of the appliance should be close to a
wall, but leaving the required distance for ventilation, as
stated in the installation instructions.
The appliance should be left for 2 hours after installation
before it is turned on, in order to allow the refrigerant to
settle.
Child Safety
Do not allow children to tamper with the controls or play
with the product.
Keep packaging materials away from children to prevent
the risk of suffocation!
Do not damage the refrigerant circuit.
Do not use electrical appliances inside the food
storage compartments of the appliance.
During Use
This appliance is designed for domestic use only,
specifically for the storage of edible foodstuffs. It is
not intended for commercial or industrial use.
Containers with flammable gases or liquids can leak
at low temperatures. Do not store any containers with
flammable materials, such as spray cans, fire
extinguisher refill cartridges etc. in the appliance.
Frozen food should not be refrozen once it has
thawed out.
Do not place carbonated or fizzy drinks in the freezer
compartment.
Ice lollies can cause 'frost/freezer burns' if consumed
straight from the freezer.
Do not remove items from the freezer compartment if
your hands are damp/wet, as this could cause skin
abrasions or frost/freezer burns.
Bottles and cans must not be placed in the freezer
compartment they can burst when the contents
freeze.
Manufacturers' recommended storage times should
be adhered to. Refer to relevant instructions.
Maintenance and Cleaning
Before cleaning, always switch off the appliance and
disconnect from the electrical supply.
When unplugging always pull the plug from the mains
socket, do not pull on the cable.
Servicing
This product should be serviced by an authorised
engineer and only genuine spare parts should be
used.
Under no circumstances should you attempt to repair
the appliance yourself. Repairs carried out by
inexperienced persons may cause injury or serious
malfunctioning. Contact your local Service Force
Centre.
Safety precautions for isobutane
Warning
The refrigerant isobutane (R 600a) is contained within
the refrigerant circuit of the appliance, a natural gas with
a high level of environmental compatibility, which is
nevertheless flammable.
Keep ventilation openings, in the appliance enclosure or
in the built-in structure, clear of obstruction.
Do not use mechanical devices or other means to
accelerate the defrosting process, other than those
recommended by the manufacturer.
This appliance does not contain gases which could
damage the ozone layer.
Avoid damaging the cooling unit.
The packaging used on this appliance marked with the
symbol is recyclable.
At the end of the Appliance Life
When disposing of your appliance use an authorised
disposal site.
Remove the plug and ensure that any locks or
catches are removed, to prevent young children
being trapped inside.
The Appliance and the Environment
Keep this instruction book for future reference and
ensure it is passed on to any new owner.
3
C ONTENT S
Instructions for the Installer
Instructions for the User
Important Safety Instructions
General Information
Description of the appliance, main parts
Switch and indicator set
Handling the appliance
Putting it into use
Controlling the temperature, setting
How to use the refrigerator
Storing in the refrigerator
Storage time and temperature of foods
How to use the freezer
Freezing
Storing in the freezer
How to make ice cubes
Some useful information and advice
Hints and ideas
How to save energy
The appliance and environment
Maintenance
Defrosting
Regular cleaning
When the refrigerator is not in use
Trouble shooting
How to change the bulb
If something does not work
Service and Spare Parts
Customer Care Department
Guarantee Conditions
4
3
5
5
6
6
6
6
7
7
8
8
8
8
8
8
8
9
9
9
11
11
11
11
11
13
13
14
Technical data
Installing the appliance
Transportation, unpacking
Cleaning
Placement
Change of door opening direction
Electrical connection
Storage time chart
15
15
15
15
15
17
18
19
INS TR UCTIONS F OR THE USER
General information
This appliance is designed for the storage of
refrigerated and frozen food in a domestic
environment.
To ensure correct operation, the appliance should
be located where the ambient temperature is
between 10-32 °C.
Description of the appliance, main parts
A - Refrigerator
B - Freezer
1. Top with indicating switch
2. Lighting box
3. Glass shelves
4. Bottle rack
5. Cooling surface
6. Defrost water drain
7. Glass shelf
8. Vegetable boxes
9. Data label
10. Freezing compartment
11. Storing compartment(s)
12. Defrost water outlet
13. Bottom plinth
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
Adjustable feet
Butter compartment lid
Egg tray
Door shelf
Door gasket
Bottle shelf
Handles
Ice tray
Condenser
Defrost water outlet tube
Spacer
Evaporator tray
Compressor
Rollers
5
Switch and indicator set
The following component can be found under a cover
in the top frame:
A. Thermostat knob of the appliance
It is for setting the temperature in the appliance.
Handling the appliance
Putting it into use
Place the accessories into the appliance then plug to
the mains socket.
The thermostat knob is under a cover in the top
frame.You can switch the appliance on and set the
temperature with it by turning the knob clockwise.
The next paragraph will give instructions for setting.
Controlling the temperature, setting
The thermostat interrupts the operation of the
appliance automatically for more or less time
depending on the setting then restarts it assuring the
required temperature.
The closer it is set to „Max.” position the more
intensive the refrigerating will be. When the thermostat
knob is set to „Medium” position (between „Min.” and
„Max.”), in the freezing compartment -18 °C, in the
fresh food compartment +5 °C can be reached.
Setting it to „Medium” position is adequate for
everyday use.
The temperature coming about in the refrigerator is
effected by not only the position of the thermostat but
the ambient temperature, frequency of door openings
and the quantity of food put into it newly, etc.
In the maximum „Max.” position - in case of
increased demand e.g. during heatwaves - the
compressor may operate continually. This does not
cause damages to the appliance.
6
How to use the refrigerator
For adequate cooling developing interior air
circulation is necessary. For this reason you are
asked not to cover the air circulation gaps behind the
shelves (e.g with tray etc.).
Do not put hot food into the refrigerator.
Allow it to reach room temperature naturally.
In this way the unnecessary frost building up can
be avoided.
Foods can take over odours from each
other. So it is essential to put foods in closed
dishes or wrap them in cellophane, aluminium
foil, grease-proof paper or cling film before
placing them into the refrigerator. This way foods
will keep their moisture e.g. vegetables will not
dry out after some days.
Storing in the refrigerator
When placing the different kinds of food take into
consideration the sketch below in figure:
1. Confectionery, ready-cooked foods, foods in
dishes, fresh meat, cold cuts, drinks
2. Milk, dairy products, foods in dishes
3. Fruits, vegetables, salads
4. Cheese, butter
5. Eggs
6. Yoghurt, sour cream
7. Small bottles, soft drinks
8. Big bottles, drinks
Storage time and temperature of
foods
The storage time chart at the end of the instruction
book gives information about storage time.
The storage time can not be determined exactly in
advance, as it depends on the freshness and handling
of the cooled food. That is why the storage time made
known is only informative.
If you do not want to use up deep-frozen foods bought
immediately they can be stored for about 1 day (until
dissolving) in the refrigerator.
7
How to use the freezer
How to make ice cubes
Freezing
To make ice cubes fill the enclosed ice cube tray
with water and put it to the frozen food
compartment. Wetting the bottom of the tray and
setting thermostatic control knob to maximum
position can shorten preparing time. After finishing
do not forget to reset the thermostatic control to the
suitable position.
The appliance can be used to freeze fresh food of
quantity specified on the data label. Freezing different
products should always be done after proper
preparing as follows.
Set the thermostat knob to a medium position.
Put the previously frozen food - or some of it - to
another basket or baskets. Put the fresh food into the
upper basket, leaving enough space for airflow. If
there is some previously frozen food left in the upper
basket, put this food into the back of the basket
avoiding the contact between the fresh food and the
already frozen food.
Run the appliance this way for 24 hours.
After 24 hours set the thermostat knob according to
your choice or leave it in a medium position, which is
in general appropriate for everyday cooling needs.
Should you want to freeze the quantity declared by the
producer, remove the upper basket from the
appliance and put the fresh food uniformly distributed
directly on the cooling surface.
Setting the thermostat knob to a higher (e.g.
maximum) position is not recommended.
Although doing so would make the freezing time
shorter, on the other hand the temperature of the
fridge compartment may go permanently below 0°C,
what yields freezing the food and drinks stored there.
Never freeze food in bigger quantity than
given in the 'Technical data' at the same
time, otherwise freezing will not be thorough and
after dissolving various deterioration may take
place (losing taste and aroma, lysing, etc.).
Do not make ice during freezing preferably,
because making ice reduces freezing capacity.
Ready ice cubes can be taken out of the tray under
running water then twist or hit it. If the ice tray
freezes to the compartment, avoid using metal
tools or knife to take it out as the cooling system
can be damaged.
Some useful information
and advice
The variable shelves are worth paying attention
to, which increases the usability of the fresh food
compartment considerably. Rearranging the
shelves is also possible when the door is open at
an angle of 90°.
After opening and closing the door of freezer
vacuum will rise inside the appliance because of
the low temperature. So wait 2-3 minutes after
closing the door - if you want to open it again while inner pressure equalises.
Take care of operating the freezer at a position of
thermostatic control so that the inside
temperature can never go above -18 °C, since
temperature higher than this can deteriorate
frozen foods.
It is practical to make sure of faultless operation
of the appliance daily so as to notice possible
failure in time and prevent deterioration of frozen
foods.
Storing in the freezer
Hints and ideas
It is practical to replace frozen products into the
basket(s) after freezing has finished. Doing this you
could make room in the freezing compartment for
another freezing. Intermediate freezing does not
deteriorate foods already stored.
In large quantities of food are to be stored, remove the
baskets except the lowermost one from appliance and
place food on the cooling surface.
Do not forget to keep to the storage time given
on the packaging of frozen products if you buy
them frozen. To store home-frozen products see the
storing instructions placed in the door of the freezer.
Symbols signify the various foods, numbers mean
maximum storing time given in months.
It is safe to store quick-frozen, frozen foods only
if they have not dissolved even for a short time
until placing them into the freezer. If the deep-frozen
food has already dissolved, refreezing is not
recommended, it has to be used up as soon as
possible.
8
In this chapter practical hints and ideas are given
about how to use the appliance to reach maximum
energy saving and there is environmental
information about the appliance as well.
How to save energy
Avoid putting the appliance in a sunny place and
near anything that gives off heat.
Be sure that the condenser and the compressor
are well ventilated. Do not cover the sections
where ventilation is.
Wrap products in tightly closing dishes or cling
film to avoid building up unnecessary frost.
Do not leave the door open longer than
necessary and avoid unnecessary openings.
Put warm foods into the appliance only when
they are at room temperature.
Keep the condenser clean.
The appliance and environment
This appliance does not contain gases which could
damage the ozone layer, in either its refrigerant circuit
or insulation materials. The appliance shall not be
discarded together with the urban refuse and rubbish.
Avoid damaging the cooling unit, especially at the rear
near the heat exchanger. Information on your local
disposal sites may be obtained from your municipal
authorities.
The materials used on this appliance marked with the
sympol
are recyclable.
Maintenance
Defrosting
Bleeding part of the moisture of cooling chambers in
form of frost and ice goes with the operation of the
appliance.
Thick frost and ice has an insulating effect, so it
reduces cooling efficiency as the temperature
increases in the cooling chambers, they need more
energy.
At this type of appliance defrosting the cooling surface
of the refrigerator is automatic without any external
intervention.The thermostatic control interrupts the
operation of compressor at regular intervals for more
or less time - during this cooling is interrupted - the
temperature of the cooling surface goes above 0 °C
due to interior heating load of the compartment, so
defrosting occurs. When the surface temperature of
the cooling surface has reached +3 - +4 °C the
thermostatic control restarts operation of the system.
Melting water flows through defrost water outlet
leaded through the back into the evaporator tray
maintained on the top of compressor and evaporates
due to its warmth.
Check and clean the outlet of melting
water coming during defrosting regularly a label inside the appliance warns you for this. If
it is clogged the melting water gathered can
cause earlier failure as it can go to the insulating
of the appliance.
Clean the melting water outlet with the supplied pipe
scraper that can be seen in the figure. The pipe
scraper has to be stored in the outlet.
The most typical case of clogging up in the melting
water outlet when you put food wrapped in some
paper into the appliance and this paper contacts back
plate of the refrigerator and freezes to it. If you remove
the food right at this moment the paper will tear and it
can cause clogging up in the outlet by getting into it.
So you are asked to be careful - because of the above
- when placing foods wrapped in paper into the
appliance.
9
In case of increased demand e.g. during
heatwaves, the refrigerator temporarily happens
to operate constantly - during this the automatic
defrosting does not work.
Remaining small ice and frost stains on back plate of
the refrigerator after defrosting period is not abnormal.
The freezer can not be equipped with automatic
defrosting set since the deep-frozen and frozen foods
do not endure melting temperature.
When small frost and ice occurs scrape off and
remove frost and ice coating with the supplied plastic
scraper.
When ice coating is so thick that it cannot be removed
with the plastic scraper, the cooling gill have to be
defrosted. Frequency of defrosting depends on usage
(generally 2-3 times a year).
Take the frozen foods out of the appliance, and put
them into a basket lined with paper or cloth. Store
them in a possibly cool place or replace them into
another refrigerator.
Pull out the mains plug from the mains socket, so both
parts of the appliance are out of operation.
Open the doors of both parts of the appliance and
clean the refrigerator according to 'Regular cleaning'.
Maintain and clean the freezer as following:
Sweep off the melting water with a cloth or sponge in
direction of sides of the cooling plates. The melting
water swept down gathers in the outlet channel
practically formed in the bottom of the appliance and
can be removed according to figure.
Put an adequately high bowl or dish under the outlet.
The bowl in figure is not a piece of accessories to the
appliance!
Wipe the surfaces after defrosting and leading the
water out.
Put the mains plug into the mains socket and put
foods taken out back to their places.
It is recommended to operate the appliance at the
highest position of the thermostatic control for some
hours so that it can reach the sufficient storing
temperature as soon as possible.
10
Regular cleaning
It is recommended to wash the inside of the refrigerator in
3-4 weeks time using lukewarm water then wipe it (it is
practical to clean the inside of the freezer and defrost it at
a time).
Household cleaner or soap must not be used.
After breaking the circuit wash the appliance with
lukewarm water then wipe it. Clean the door gasket with
clean water. After cleaning apply voltage to the appliance.
It is recommended to remove the dust and dirt collected
on the back of the refrigerator and the condenser and to
clean the evaporative tray on top of the compressor once
or twice a year.
When the refrigerator
is not in use
In case the appliance will not be used for a long time
follow these steps:
Break the circuit of the appliance.
Remove foods from the refrigerator.
Defrost and clean it as written before.
Leave the door open to avoid a build up of air inside.
Trouble shooting
How to change the bulb
Should the light fail to work you can change it as below:
Break the circuit of the appliance.
Press the rear hook (1) and at the same time slide the
cover in the direction indicated by the arrow (2). So the
bulb can be replaced. (Bulb type: T 25 230-240 V,
25 W, E 14 thread)
After changing the bulb replace the cover, snap it in
place and apply voltage to the appliance.
If something does not work
During operation of the appliance some smaller but
annoying trouble can often occur, which does not
require calling a technician out. In the following chart
information is given about them to avoid unnecessary
charges on service.
We draw your attention that operation of appliance goes
with certain sounds (compressor- and circulating
sound). This is not trouble, but means normal
operation.
We draw it to your attention again that the
appliance operates discontinuously, so the
stopping of compressor does not mean being nocurrent. That is why you must not touch the electrical
parts of the appliance before breaking the circuit.
11
Problem
Possible cause
It is too warm in the Thermostatic control can be set wrongly.
refrigerator.
If products are not cold enough or
placed wrongly.
The door does not close tightly or it is not
shut properly.
It is too warm in the Thermostatic control can be set wrongly.
freezer.
The door does not close tightly or it is not
shut properly.
Products in big quantity to be frozen
were put in.
Products to be frozen are placed too
closely to each other.
Water flows at the back It is normal. During automatic defrosting
plate of the refrigerator. frost melts on the back plate.
Water flows into the The outlet of the chamber can be
chamber.
clogged up.
Products placed in can prevent water
from flowing into the collector.
Water flows onto the The melting water outlet flows not into
floor.
the evaporative tray above the
compressor.
There are too much frost Products are not wrapped properly.
and ice.
Doors are not shut properly or do not
close tightly.
The thermostatic control can be set
wrongly.
The
compressor The thermostatic control is set wrongly.
operates continually.
Doors are not shut properly or do not
close tightly.
Products in big quantity to be frozen
were put in.
Too warm food was put in.
The appliance is in too warm place.
Solution
Set the thermostat knob to higher
position.
Place the products to the appropriate
place.
Check if the door closes well and the
gasket is unhurt and clean.
Set the thermostat knob to higher
position.
Check if the door closes well and the
gasket is unhurt and clean.
Wait some hours and then check the
temperature again.
Place the products in a way so that
cold air could circulate among them.
Clean the outlet.
Replace the products so that they can
not touch the back plate directly.
Put the melting water outlet to the
evaporative tray.
Wrap the products better.
Check if the doors close well and the
gaskets are undamaged and clean.
Set the thermostat knob to a position
that gives higher temperature.
Set the thermostat knob to a position
that gives higher temperature.
Check if the doors close well and the
gaskets are unhurt and clean.
Wait some hours and then check the
temperature again.
Put food at max. room temperature.
Try to reduce the temperature in the
room where the appliance stands.
The appliance does not Plug is not connected to the mains Connect the mains plug properly.
work at all. Neither socket properly.
cooling, nor lighting The fuse burnt out.
Change the fuse.
works.
Start the appliance according to
The thermostatic control is not on.
instructions in chapter 'Putting it into
use'.
There is no voltage in the mains socket. Call an electrician.
(Try to connect another appliance into it.)
The appliance is noisy. The appliance is not supported properly. Check if the appliance stands stable
(all the four feet should be on the
floor).
Inasmuch as the advice does not lead to result, call the nearest brand-mark service.
12
Ser vice and Spar e P ar ts
In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact your
local Service Force Centre by telephoning:08705 929929
Your telephone call will be automatically routed to the Service Force Centre covering your post code area.
For the address of your local Service Force Centre and further information about Service Force, please visit
the website at www.serviceforce.co.uk
Before calling out an engineer, please ensure you have read the details under the heading "Something Not
Working."
When you contact the Service Force Centre you will need to give the following details:
1. Your name, address and post code
2. Your telephone number
3. Clear and concise details of the fault
4. The model and serial number of the appliance (found on the rating plate)
5. The purchase date
Please note that a valid purchase receipt or guarantee documentation is required for in-guarantee
service calls.
For Customer Service in Ireland please
contact us at the aderess below:
Zanussi - Electrolux
Electrolux Group (Irl) Ltd
Long Mile Road
Doublin 12
Republic of Ireland
Tel: +353 (0)1 4090751
Email: service.eid@electrolux.ie
Cus t omer Car e Depar tment
For general enquiries concerning your Zanussi - Electrolux appliance or for further information on
Zanussi - Electrolux products, please contact our Customer Care Department by letter or telephone at the
adresses below or visit our website at www.zanussi-electrolux.co.uk
Customer Services Department
Major Appliances
Zanussi - Electrolux
Addington Way
Luton
Bedfordshire
LU4 9QQ
08705 727727 (*)
*calls to this number may be recorded for training purposes.
13
Guar ant ee Conditions
We Zanussi - Electrolux undertake that if within 12
months of the date of the purchase this
ZANUSSI - ELECTROLUX appliance or any part
thereof is proved to be defective by reason only of
faulty workmanship or materials, the company will, at
our option repair or replace the same FREE OF
CHARGE for labour, materials or carriage on condition
that:
The appliance has been correctly installed and
used only on the electrical supply stated on the
rating plate.
The appliance has been used for normal domestic
purposes only, and in accordance with the
manufacturer's instructions.
The appliance has not been serviced, maintained,
repaired, taken apart or tampered with by any
person not authorised by us.
All service work under this guarantee must be
undertaken by a Service Force Centre.
Any appliance or defective part replaced shall
become the Company's property.
Home visits are made between 8.30am and 5.30pm
Monday to Friday. Visits may be available outside
these hours in which case a premium will be charged.
EXCLUSIONS
This Guarantee does not cover:
Damage or calls resulting from transportation,
improper use or neglect, the replacemet of any light
bulbs or removable parts of glass or plastic.
Costs incurred for calls to put right an appliance
improperly installed or calls to appliances outside
the United Kingdom.
Appliances found to be in use within a commercial
environment, plus those which are the subject of
rental agreements.
Products of Zanussi - Electrolux manufacture
which are not marketed by Zanussi - Electrolux.
The guarantee is in addition to your statutory and legal
rights.
14
EUROPEAN GUARANTEE
If you should move to another country within
Europe then your guarantee moves with you to your
new home subject to the following qualifications:
The guarantee starts from the date you first
purchased your product.
The guarantee is for the same period and to the
same extent for labour and parts as exists in the
new country of use for this brand or range of
products.
This guarantee relates to you and cannot be
transferred to another user.
Your new home is within the European
Community (EC) or European Free Trade Area.
The product is installed and used in accordance
with our instructions and is only used
domestically, i.e. a normal household.
The product is installed taking into account
regulations in your new country.
Before you move please contact your nearest
Customer Care Centre, listed below, to give them
details of your new home. They will then ensure that
the local Service Organisation is aware of your
move and able to look after you and your
appliances.
France
Germany
Italy
Sweden
UK
Ireland
Senlis
Nurenberg
Pordenone
Stockholm
Luton
Dublin
+33 (0) 344 62 29 29
+49 (0) 800 234 7378
+39 (0) 0434 39 4700
+46 (0) 8 672 53 90
+44 (0) 8705 727 727
+353 (0)1 4090751
Ins tr uctions f or the Ins t aller
Technical data
Model
Gross capacity (l)
Net capacity (l)
Width (mm)
Height (mm)
Depth (mm)
Energy consumption (kWh/24h)
(kWh/year)
Energy class, according to EU standards
Freezing capacity (kg/24h)
Rising time (h)
Rated current (A)
Weight (kg)
Number of compressors
ZERB 8643
Freezer:
249
Refrigerator: 109
Freezer:
245
Refrigerator: 92
595
1890
632
0,96
350
A
4
20
0,9
73
1
Installing the appliance
Transportation, unpacking
Class of climate
Ambient temperature
It is recommended to deliver the appliance in
original packaging, in vertical position
considering the protective warning on packaging.
SN
+10 ... +32 °C
N
+16 ... +32 °C
After each transportation the appliance must not be
switched on for approx. 2 hours.
ST
+18 ... +38 °C
Unpack the appliance and check if there are damages
on it. Report possible damages immediately to the
place you bought it. In that case retain packaging.
Cleaning
Remove every adhesive tape and everything else,
which ensure the accessories not to move in the
appliance.
Wash the inside of the appliance using lukewarm
water and mild detergent. Use soft cloth.
After cleaning wipe out the inside of the appliance.
If the ambient temperature goes below the lower
data the temperature of the cooling compartment
can go beyond the prescribed temperature.
If the ambient temperature goes beyond the upper
data this means longer operating time of the
compressor, breakdown in the automatic
defrosting increasing temperature in the cooling
compartment or increasing energy consumption.
Mount the spacers supplied in the plastic bag
of the accessories. Hold the spacer as shown
on the Fig., knock it home, then turn it by 90°.
(Into the oval holes of back side of the
appliance.)
Placement
The ambient temperature has an effect on the energy
consumption and proper operation of the appliance.
When placing, take into consideration that it is
practical to operate the appliance between ambient
temperature limits according to the climate class that
is given in the chart below and can be found in the
data label.
15
When placing the appliance ensure that it stands level.
This can be achieved by two adjustable feet at the
bottom in front.
Do not stand the appliance on a sunny place or close
to a radiator or cooker.
If it is unavoidable because of furnishing and the
appliance has to be stood near a cooker take these
minimum distances into consideration:
In case of gas or electric cooker 3 cm must be left,
when it is less put a 0,5-1 cm non-flam insulation
between the two appliances.
In case of oil or coal-fired stove the distance must
be 30 cms since they give off more heat.
The refrigerator is designed to operate when it is
totally pushed to the wall.
When placing the refrigerator keep minimal
distances recommended in figure.
A : placing it under a wall-cupboard
B : placing it freely
16
Change of door opening direction
Should the setting-up place or handling demand it,
door-opening direction can be refitted from righthanded to left-handed.
Appliances on the market are right-handed.
Following operations are to be done on the basis of
figures and explanations:
To perform the operations listed below it is
recommended to ask another person for help who
safely can keep the doors while performing the
operations.
Disconnect the appliance from the electricity
supply.
Open the doors and dismount the double door
hinge (a,b) by removing the screws (2 pieces) (c).
(fig.2)
Take off the double door hinge (a,b,c) by gradually
removing it from the cabinet, slightly tilting both
doors. Do not forget to remove the plastic spacer
(b) under the hinge. (fig.2)
Take off the refrigerator door by pulling it slightly
downwards.
Take of the freezer door by pulling it slightly
upwards.
Remove the plug on the upper side of the
refrigerator door and put it to the other side.
Remove the plug on the upper side of the freezer
door and put it to the other side.
Unscrew the top door hinge pin (d) of the
refrigerator then screw it back on the other side.
(fig.1)
Remove the insert of the plinth (e) by a screwdriver.
(fig.3)
Unmount the lower hinge pin (f) and its washer (h)
and mount them on the other side. (fig.3)
Replace the insert of the plinth (e) on the other
side.
Remove the covering nails (3 pieces) (n,k) of the
double door holder on the left side and put them to
the other side. (fig.2)
Fit the pin of the double door hinge (m) into the left
drill of the freezer door. (fig.2)
Fit the freezer door to the lower door hinge pin (f).
(fig.3)
Fit the refrigerator door to the upper door hinge pin
(d) then slightly tilting both doors fit the pin of the
double door hinge (m) into the left drill of the
refrigerator door.
Opening both doors fix the double door hinge onto
the left side using the screws (2 pieces) (c). Do not
forget to replace the plastic spacer (b) under the
hinge. Be careful that the door edges are parallel
with the edge of the mantle.
Put over the handles (r) on the other side and put
the plastic covering nails (p) supplied in the plastic
bag of this instruction book into the holes set free.
(fig.4)
Put the appliance to its place, set it level, and apply
to voltage it.
In case you do not want to perform the procedures
above, call the nearest brand-mark service.
Technicians will accomplish the refitting expertly for
charge.
fig. 1.
fig. 2.
fig. 3.
fig. 4.
17
Electrical Connection
Any electrical work required to install this
appliance should be carried out by a
qualified electrician or competent person.
This appliance must be earthed.
The manufacturer declines any liability should
these safety measures not be observed.
Electrical Requirements
Before switching on, make sure the electricity supply
voltage is the same as that indicated on the appliance
rating plate.
The appliance is supplied with a 13 amp plug fitted. In
the event of having to change the fuse in the plug
supplied, a 13 amp ASTA approved (BS 1362) fuse
must be used. Should the plug need to be replaced
for any reason. The wires in the mains lead are
coloured in accordance with the following code:
Green and Yellow:
Earth
Blue:
Neutral
Brown:
Live
The wire coloured green and yellow must be
connected to the terminal marked with the letter „E“ or
by the earth symbol
or coloured green and yellow.
The wire coloured blue must be connected to the
terminal „N“ or coloured black.
The wire coloured brown must be connected to the
terminal marked „L“ or coloured red.
Upon completion there must be no cut, or stray
strands of wire present and the cord clamp must be
secure over the outer sheath.
Important!
The plug is must still be accessible after the
appliance has been installed.
The appliance should not be connected to the
electrical supply by means of an extension cable.
In case that the electrical cable has to be
replaced, please contact your local Service Force
Centre.
This appliance complies with the following
E.E.C. Directives:
89/336 EEC of 03.05.89 (Electromagnetic
Compatibility
Directive)
and
subsequent
modifications.
18
A/ZE/15. (05)
73/23 EEC of 19.02.73 (Low Voltage Directive)
and subsequent modifications,
S t or age time char t
Time and method of storage of fresh foods in the refrigerator
Foods
Raw meat
Cooked meat
Roasted meat
Raw minced meat
Cooked minced meat
Cold cuts
Fresh fish
Cooked fish
Tinned fish, open
Fresh chicken
Fried chicken
Fresh duck, goose
Roasted duck, goose
Butter unopened
Butter opened
Milk
Cream
Sour cream
Cheese (hard)
Cheese (soft)
Egg
Spinach, sorrel
Green peas, green beans
Mushroom
Carrot
Tomato
Cabbage
Fruits (Strawberry,
raspberry, etc.)
Tinned fruits opened
Cakes filled with cream
Storage time in days
3
4
5
6
x
x
x
X
x
x
x
X
x
x
1
X
X
X
X
X
X
2
X
X
X
X
X
x
x
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
x
X
x
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
x
x
x
X
X
X
X
X
x
X
x
X
X
X
X
x
X
x
X
X
X
x
x
x
X
X
x
x
x
X
X
X
X
x
X
x
X
X
X
X
X
X
X
X
X
X
X
x
x
x
x
Method of packaging
7
x
x
x
x
x
x
x
X
x
x
x
x
x
x
X
x
x
X
x
x
X
x
X
x
X
x
X
x
X
x
X
x
x
X
X
X
x
x
X
X
x
X
X
x
x
x
cling film, airtight
dish covered
dish covered
dish covered
dish covered
cling film, cellophane, greaseproof paper
cling film, airtight
dish covered
dish covered
cling film, airtight
dish covered
cling film, airtight
dish covered
original packaging
original packaging
original packaging
plastic box
plastic box
aluminium foil
cling film
cling film
cling film
cling film
cling film
cling film
cling film
cling film
dish covered
dish covered
Notation:
X
x
recommended storage time
maximum recommended storage time
19
2005. 07. 04.
ELECTROLUX HOME PRODUCTS OPERATIONS EUROPE
From the Electrolux Group. The world’s No.1 choice.
The Electrolux Group is the world's largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million Electrolux
Group products (such as refrigerators, cookers, washing machines, vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of
approx. USD 14 billion in more than 150 countries around the world.
Printed By Océ Hungária Kft.
© Electrolux plc 2005
Download PDF

advertising