Vivotek IP7134 User`s manual
Vivotek IP7134 is a high-performance network camera offering advanced surveillance capabilities for both indoor and outdoor use. It features a built-in microphone for audio recording, a privacy button for added security, and general I/O terminals for connecting external devices like sensors and alarms. With its vandal-proof and weather-resistant design, it's ideal for various applications, including retail stores, offices, and public areas.
advertisement
P/N:625007400G
Warning Before Installation
Power off the Network Camera as soon as smoke or unusual odors are detected.
Contact your distributor in the event of occurrence.
Keep the Network Camera away from water. If the Network Camera becomes wet, power off immediately.
Contact your distributor in the event of occurrence.
Do not place the Network Camera around heat sources, such as a television or oven.
Refer to your user’s manual for the operating temperature.
Keep the Network Camera away from direct sunlight.
Do not place the Network Camera in high humidity environments.
EN - 1
Do not place the Network Camera on unsteady surfaces.
Do not touch the Network Camera during a lightning storm.
Do not disassemble the Network
Camera.
Do not drop the Network Camera.
Do not insert sharp or tiny objects into the Network Camera.
EN - 2
1
Package Contents
IP7133 / IP7134 Power Adapter
Camera Stand
P
Software CD
Quick Installation Guide Warranty Card
Screws
EN - 3
2
Physical Description
Front Panel
Built-in Microphone
Lens
Status LED
Back Panel
P
Privacy Button
Power Cord Socket
Recessed Reset Button
RESET
ETHERNET
IO
1 2 3 4
Ethernet 10/100
RJ45 Socket
General I/O
Terminal Block
3
Network Deployment
1. If you have external devices such as sensors and alarms, make connections from general I/O terminal block.
1: Power
2: Digital output
3: Digital input
4: Ground
2. Connect the camera to a switch via Ethernet cable.
● Use Category 5 Cross Cable when Network Camera is directly connected to PC.
3. Connect the supplied power cable from the camera to a power outlet.
EN - 4
POWER
COLLISION
1
2 3 4
5
LINK
RECEIVE
PARTITION
4
Assigning an IP Address
1. Install “Installation Wizard 2” from the Software Utility directory on the software CD.
2. The program will conduct an analysis of your network environment. After your network is analyzed, please click on the “Next” button to continue the program.
Installation
Wizard 2
3. The program will search for VIVOTEK Video Receivers, Video Servers, and Network
Cameras on the same LAN.
4. After searching, the main installer window will pop up. Click on the MAC that matches the one labeled on the bottom of your device to connect to the Network Camera via Internet
Explorer.
IP7133
MAC:0002D1533318
!
Assembled from tested components
Complete system not tested
FCC ID: RRK2005100093
0002D1533318
5. Retrieve live video through a web browser or recording software.
EN - 5
5 Confi gure the Wireless Connection
(IP7134 only)
1. Check the SSID for your wireless access point (AP).
2. Go to the IP7134 Confi guration page > Wireless LAN.
3. Type in the SSID the same as your AP.
4. Select the Wireless mode as "Infrastructure".
5. Click Save. The Network Camera will reboot.
6. Wait for the live image to be reloaded to your browser. Then, unplug the power cable and
Ethernet cable from the Network Camera.
7. Replug the power cable to the camera. The Network Camera will now operate in wireless mode.
ADSL/Cable/Hub
AP
POWER COLLISION
1 2
3 4 5
LINK
RECEIVE
PARTITION
Note:
1. SSID, abbreviated from Service Set Identifi er, is the name assigned to the wireless network. The IP7134 factory SSID setting is set to "default".
2. Select "Ad-Hoc" wireless mode if you want the IP7134 to communicate without using an
AP or wireless router.
For further setup, please refer to the user's manual on the software CD.
EN - 6
advertisement
Key Features
- High-resolution imaging with 1/2.8" progressive scan CMOS sensor
- H.264 and MJPEG compression for efficient bandwidth usage
- 3-axis gimbal for flexible positioning
- Built-in microphone and speaker for two-way audio communication
- Motion detection and privacy masking for enhanced security
- IPv6 and ONVIF support for easy integration with other network devices
- Supports wireless connectivity for easy installation and deployment
Frequently Answers and Questions
What is the maximum resolution that the IP7134 can record?
Does the IP7134 support audio recording?
Can the IP7134 be used outdoors?
What is the field of view of the IP7134?
What type of lens does the IP7134 have?
What is the minimum illumination required for the IP7134 to operate?
Related manuals
advertisement