EFX® 833 Elliptical Fitness Crosstrainer™ - Experience™ Series

EFX® 833 Elliptical Fitness Crosstrainer™ - Experience™ Series
Operating and Maintaining
the P30 Console
Precor Incorporated
20031 142nd Avenue NE
P.O. Box 7202
Woodinville, WA USA 98072-4002
P30 OM 301096-301 rev E, en
December 2012
Edition Information
OPERATING AND MAINTAINING THE P30 CONSOLE
P/N 301096-301 rev E
Copyright © December 2012 Precor Incorporated. All rights
reserved. Specifications subject to change without notice.
Trademark Note
Precor, AMT, EFX, and Preva are registered trademarks of
Precor Incorporated. Other names in this document may be
the trademarks or registered trademarks of their respective
owners.
Intellectual Property Notice
All rights, title, and interests in and to the software of the
Preva Business Suite, the accompanying printed materials,
any copies of such software, and all data collected via the
Preva Business Suite, are exclusively owned by Precor or its
suppliers, as the case may be.
Precor is widely recognized for its innovative, award-winning
designs of exercise equipment. Precor aggressively seeks U.S.
and foreign patents for both the mechanical construction and
the visual aspects of its product design. Any party
contemplating the use of Precor product designs is hereby
forewarned that Precor considers the unauthorized
appropriation of its proprietary rights to be a very serious
matter. Precor will vigorously pursue all unauthorized
appropriation of its proprietary rights.
Precor Incorporated
20031 142nd Ave NE, P.O. Box 7202
Woodinville, WA 98072-4002
1-800-347-4404
http://www.precor.com
Important Safety Instructions
Important: Save these instructions for future reference.
Read all instructions in the documentation provided with your
exercise equipment, including all assembly guides, user
guides, and owner’s manuals, before installation of this
device.
Note: This product is intended for commercial use.
The display apparatus (hereinafter referred to as the console)
is intended to be shipped with new Precor exercise equipment
(hereinafter referred to as the base unit). It is not packaged for
individual sale.
WARNING
To prevent injury, the console must be
attached securely to the base unit following all
assembly and installation instructions shipped
with the base unit. The console is intended to
be connected to AC mains power through the
furnished power supply ONLY. It should be
powered on only when installed as described
in the assembly and installation instructions
shipped with the base unit. The console is
intended for use only with Precor fitness
equipment, not as a standalone device.
Safety Precautions
Always follow basic safety precautions when using this
equipment to reduce the chance of injury, fire, or damage.
Other sections in this manual provide more details of safety
features. Be sure to read these sections and observe all safety
notices. These precautions include the following:

Read all instructions in this guide before installing and
using the equipment and follow any labels on the
equipment.
4
Operating and Maintaining the P30 Console







Make sure all users see a physician for a complete
physical examination before they begin any fitness
program, particularly if they have high blood pressure,
high cholesterol or heart disease; have a family history of
any of the preceding conditions; are over the age of 45;
smoke; are obese; have not exercised regularly in the past
year; or are taking any medication.
French equivalent of the above notice, for Canadian
markets: Il est conseillé aux utilisateurs de subir un examen
médical complet avant d’entreprendre tout programme
d’exercice, en particulier s’ils souffrent d’hypertension
artérielle, ou de cardiopathie ou ont un taux de cholestérol
élevé, s’ils ont des antécédents familiaux des précédentes
maladies, s’ils ont plus de 45 ans, s’ils fument, s’ils sont
obèses, s’ils n’ont pas fait d’exercices réguliers au cours de
l’année précédente ou s’ils prennent des médicaments. Si vous
avez des étourdissements ou des faiblesses, arrêtez les
exercices immédiatement.
Do not allow children, or people unfamiliar with the
operation of this equipment, on or near it. Do not leave
children unsupervised around the equipment.
Make sure all users wear proper exercise clothing and
shoes for their workouts and avoid loose or dangling
clothing. Users should not wear shoes with heels or
leather soles, and they should check the soles of their
shoes to remove any dirt and embedded stones. They
should also tie long hair back.
Never leave the equipment unattended when it is plugged
in. Unplug the equipment from its power source when it is
not in use, before cleaning it, and before providing
authorized service.
Note: The optional power adapter is considered a power
source for self-powered equipment.
Use the power adapter provided with the equipment. Plug
the power adapter into an appropriate, grounded power
outlet as marked on the equipment.
Care should be taken when mounting or dismounting the
equipment.
For Treadmills: Do not use typing or web surfing features
while walking at speeds that exceed a slow and relaxed
leisurely pace. Always stabilize yourself by holding a
stationary handle bar while using typing or web surfing
features.
Important Safety Instructions







5
For AMT and EFX: Always stabilize yourself by holding a
stationary handle bar while using typing or web surfing
features.
Read, understand, and test the emergency stop
procedures before use.
Keep the power cord or optional power adapter and plug
away from heated surfaces.
Route power cables so that they are not walked on,
pinched, or damaged by items placed upon or against
them, including the equipment itself.
Ensure the equipment has adequate ventilation. Do not
place anything on top of or over the equipment. Do not
use on a cushioned surface that could block the
ventilation opening.
Assemble and operate the equipment on a solid, level
surface.
SPACING—The below minimum spacing
recommendations are based on a combination of the
ASTM (U.S.) voluntary standards and EN (European)
regulations as of October 1, 2012, for access, passage
around, and emergency dismount:
 Treadmills—a minimum of 0.5 m (19.7 in.) on each
side of the treadmill and 2 m (78 in.) behind the
machine.
 Cardio equipment other than treadmills—a
minimum of 0.5 m (19.7 in.) on at least one side, and
0.5 m (19.7 in.) behind or in front the machine.
Careful consideration should be given to the
requirements of the Americans with Disabilities Act
(ADA), US Code 28 CFR (see Section 305). ASTM
standards are voluntary and may not reflect current
industry standards. The actual area for access, passage
around, and emergency dismount is the responsibility of
the facility. The facility should consider the total space
requirements for training on each unit, voluntary and
industry standards, and any local, state, and federal
regulations. Standards and regulations are subject to
change at any time.
Important: These spacing recommendations should be used
when positioning equipment away from sources of heat, such
as radiators, heat registers, and stoves. Avoid temperature
extremes.
6
Operating and Maintaining the P30 Console













Keep equipment away from water and moisture. Avoid
dropping anything on or spilling anything inside the
equipment to prevent electric shock or damage to the
electronics.
When using the treadmill, always attach the safety clip to
your clothing before beginning your workout. Failure to
use the safety clip may pose a greater risk of injury in the
event of a fall.
Keep in mind that heart rate monitors are not medical
devices. Various factors, including the user’s movement,
may affect the accuracy of the heart rate readings. The
heart rate monitors are intended only as exercise aids in
determining heart rate trends in general.
Do not operate electrically powered equipment in damp
or wet locations.
Never operate this equipment if it has a damaged cord or
plug, if it is not working properly, or if it has been dropped,
damaged, or exposed to water. Call for service
immediately if any of these conditions exist.
Maintain the equipment to keep it in good working
condition, as described in the Maintenance section of the
owner’s manual. Inspect the equipment for incorrect,
worn, or loose components, and then correct, replace or
tighten prior to use.
If you plan to move the equipment, obtain help and use
proper lifting techniques.
Equipment Weight Restrictions: Do not use the treadmill
if you weigh more than 500 pounds (225 kg). If you weigh
more than 350 pounds (160 kg), do not run on the
treadmill. For all other fitness equipment, the weight limit
is 350 pounds (160 kg).
Use the equipment only for its intended purpose as
described in this manual. Do not use accessory
attachments that are not recommended by Precor. Such
attachments may cause injuries.
Do not operate the equipment where aerosol (spray)
products are being used or where oxygen is being
administered.
Do not use outdoors.
Do not attempt to service the equipment yourself, except
to follow the maintenance instructions in the owner’s
manual.
Never drop or insert objects into any opening. Keep hands
away from moving parts.
Important Safety Instructions


7
Do not set anything on the stationary handrails,
handlebars, control console, or covers. Place liquids,
magazines, and books in the appropriate receptacles.
Do not lean on or pull on the console at any time.
CAUTION: DO NOT remove the cover, or you may risk injury due
to electric shock. Read the assembly and maintenance guide
before operating. There are no user-serviceable parts inside.
Contact Customer Support if the equipment needs servicing. For
use with single phase AC power only.
Hazardous Materials and Proper Disposal
The batteries within self-powered equipment contain
materials that are considered hazardous to the environment.
Federal law requires proper disposal of these batteries.
If you plan to dispose of your equipment, contact Precor
Commercial Products Customer Support for information
regarding battery removal. Refer to Obtaining Service.
Product Recycling and Disposal
This equipment must be recycled or discarded according to
applicable local and national regulations.
Product labels, in accordance with European Directive
2002/96/EC concerning waste electrical and electronic
equipment (WEEE), determine the framework for the return
and recycling of used equipment as applicable throughout the
European Union. The WEEE label indicates that the product is
not to be thrown away, but rather reclaimed upon end of life
per this Directive.
In accordance with the European WEEE Directive, electrical
and electronic equipment (EEE) is to be collected separately
and to be reused, recycled, or recovered at end of life. Users
of EEE with the WEEE label per Annex IV of the WEEE
Directive must not dispose of end of life EEE as unsorted
municipal waste, but use the collection framework available
to customers for the return, recycling, and recovery of WEEE.
Customer participation is important to minimize any potential
effects of EEE on the environment and human health due to
the potential presence of hazardous substances in EEE. For
proper collection and treatment, refer to Obtaining Service.
8
Operating and Maintaining the P30 Console
Regulatory Notices for Cardiovascular
Exercise Equipment
The regulatory information in this section applies to the
exercise equipment and its control console.
Safety Approvals for Cardiovascular Equipment
Precor equipment has been tested and found to comply with
the following applicable safety standards.
Cardiovascular Type Equipment:
 CAN/CSA, IEC, EN 60335-1 (Household and similar

electrical appliances - Safety)
EN 957 (Stationary training equipment, class S/B
compliant equipment)
Radio Frequency Interference (RFI)
This Precor exercise equipment conforms to the following
national standards defining acceptable limits for radio
frequency interference (RFI).
Federal Communications Commission, Part 15
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a commercial
installation. The equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in
accordance with the owner’s manual instructions, can cause
harmful interference to radio communications.
Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
WARNING
Per FCC rules, changes or modifications not
expressly approved by the manufacturer could
void the user’s authority to operate the
equipment.
Important Safety Instructions
9
Industry Canada
This device complies with RSS-210:2007 of the Spectrum
Management & Telecommunications Radio Standards
Specification. Operation is subject to the following two
conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference
received, including interference that may cause undesired
operation.
This Class A digital apparatus complies with Canadian
ICES-003.
Cet appareil numérique de la classe A est conforme à la norme
NMB-003 du Canada.
ATTENTION: Haute Tension
Débranchez avant de réparer
European Applications
CE compliance is claimed to the following directives:
2004/108/EC EMC Directive
2006/95/EC LVD Directive
2002/95/EC RoHS Directive
Directive compliance has been verified to the following
standards:







EN 55022
EN 55024
EN 60335-1
EN 60065 (P80 and PVS)
10
Operating and Maintaining the P30 Console
Electrical Recommendations: 120 V and
240 V Treadmills
Note: This is a recommendation only. NEC (National Electric
Code) guidelines or local region electric codes must be
followed.
You should have received a power cable that meets your local
electrical code requirements along with the equipment.
Precor treadmills must be connected to a 20 amp individual
branch circuit that can be shared only with one PVS. If you
need additional help with the power connections contact your
Precor authorized dealer.
Important: An individual branch circuit provides a hot conductor
and neutral conductor to a receptacle. The conductors must not be
looped, "daisy-chained", or connected to any other conductors.
The circuit must be grounded according to NEC guidelines or local
region electric codes.
Figure 1: North American 120-volt, 20-amp power receptacle
Figure 2: North American 240-volt, 20-amp power receptacle
Important Safety Instructions
11
Electrical Recommendations: All Equipment
Excluding Treadmills
Note: This is a recommendation only. NEC (National Electric
Code) guidelines or local region electric codes must be
followed.
For equipment fitted with a P80 console or Personal Viewing
System (PVS) screen a separate power connection is
required. For a 20 amp branch circuit up to 10 screens can be
connected. If the branch circuit has any other devices plugged
into the circuit, then the number of screens must be reduced
by the wattage of the other devices.
Note: The typical splitter power cords that have IEC-320 C13
and C14 plugs have a recommended maximum capacity of
five screens.
Figure 3: IEC-320 C13 and C14 plugs
Obtaining Service
Do not attempt to service the equipment except for
maintenance tasks. If any items are missing, contact your
dealer. For more information regarding customer support
numbers or a list of Precor authorized service centers, visit
the Precor web site at http://www.precor.com.
12
Operating and Maintaining the P30 Console
Table of Contents
Important Safety Instructions ................................................... 3
Safety Precautions .................................................................................3
Hazardous Materials and Proper Disposal .................................... 7
Product Recycling and Disposal ....................................................... 7
Regulatory Notices for Cardiovascular Exercise Equipment..... 8
Electrical Recommendations: 120 V and 240 V Treadmills ..... 9
Electrical Recommendations: All Equipment
Excluding Treadmills ....................................................................11
Obtaining Service..................................................................................11
Getting Started ........................................................................ 15
Activating the Console for Self-Powered Equipment ................ 15
Identifying Parts of the Console....................................................... 17
Setting Up the Console ............................................................ 21
System Settings .................................................................................... 21
Setting Club Parameter Values ....................................................... 23
Viewing the Informational Displays .............................................. 27
User ID Entry with CSAFE Equipment........................................... 32
Introducing Users to the P30 Console..................................... 33
Using the Touch Heart Rate Feature ............................................. 33
Using a Chest Strap Transmitter .................................................... 35
Using the Treadmill Safety Clip ...................................................... 35
Treadmill Auto Stop™ (Automatic Stop) Function ................... 37
Starting a Workout .................................................................. 39
Starting a Preset Programmed Workout ...................................... 39
Setting Options................................................................................... 40
Pausing and Resuming an Exercise Session .................................41
Ending a Session.................................................................................. 42
Programs .............................................................................................. 44
Maintenance ............................................................................ 47
Cleaning the Console and Display ................................................. 47
Changing the Belt (Newer Model AMT Only)............................48
14
Operating and Maintaining the P30 Console
Chapter
1
Getting Started
The P30 console offers administrators the ability to set
default values that meet their specific needs. These settings
include items like language, units of measure, and setting a
maximum allowed workout time for each piece of equipment.
Activating the Console for Self-Powered
Equipment
Precor equipment is either self-powered or externally
powered using an optional power adapter. Self-powered
equipment requires the user exercise to initialize the console.
This section provides more detail about powering equipment.
Activating the Console for Self-Powered Equipment
On self-powered equipment, when a user starts exercising,
the console initializes and displays the Welcome banner. A
minimum rate of motion must be maintained for the
Welcome banner to appear. The words PEDAL FASTER (or
the equivalent message depending on the equipment type)
appear in the display when the rate of motion drops below the
minimum requirements.
The equipment saves its battery charge by moving into a
shutdown mode. If the user does not maintain the minimum
rate of motion, a 30-second shutdown process begins.
In this mode, the console displays a countdown indicator and
ignores all keypresses. If no movement is detected or the rate
of motion remains below the minimum, the indicator changes
as the countdown continues.
Note: The user can resume exercising before the countdown
period elapses and the workout will continue from the point at
which it was paused.
16
Operating and Maintaining the P30 Console
Optional Use of the Power Adapter
An optional AC power adapter provides sustained power to
the equipment. This adapter allows you to change settings
without having to pedal the equipment. To purchase the
power adapter, contact your dealer.
If you purchase the optional power adapter, you must also
purchase the internal cable kit. The kit supplies the cable,
bracket, and fasteners that connect the power adapter to the
lower electronics board.
CAUTION: The internal cable kit must be installed by authorized
service personnel. Do not attempt installation on your own as you
could void the Precor Limited Warranty. For more information,
refer to Obtaining Service.
Important: If this equipment includes a P80 console, the optional
power adapter and the internal cable kit must still be installed to
provide continuous power to the base unit and support its internal
battery.
Once the internal cable kit is installed, you can plug the
optional power adapter into the equipment. Plug the opposite
end into the appropriate power source for your equipment
(120 V or 240 V). Review the safety instructions found at the
beginning of this manual before using the power adapter.
CAUTION: When the optional power adapter is in use, make sure
that the power supply cord does not create a safety hazard. Keep
it out of the way of traffic and moving parts. If the power supply
cord or power conversion module is damaged, it must be replaced.
The control console functions differently when the power
adapter is connected. Because the power adapter provides a
constant source of power, a user can pause for brief periods
without initiating shutdown procedures. When the pause time
limit expires and the user has not resumed exercising, the
console returns to the Welcome screen. The default pause
time is 30 seconds for all fitness equipment. Refer to the
manual for your control console for instructions on setting or
changing the pause time limit.
17
Getting Started
Identifying Parts of the Console
The following figure provides information about the console
keys. The number and actions of the console keys may differ
slightly depending on the type of equipment.
Figure 4: P30 console keys
Table 1. Parts of the console
Number Part Name
Average Speed
Pace
Details
Use the ▲ or ▼ arrows to change
which item you want to display
Distance
Calories
Displays the number of calories you
have burned
Heart Rate
Displays your heart rate
Time Elapsed
Use the ▲ or ▼ arrows to change
how the time is displayed
Time Remaining
Upper Text Display Scrolls information to guide the user
18
Operating and Maintaining the P30 Console
Number Part Name
•
•
•
•
Muscle
Monitor - EFX
Details
•
Stride Length AMT
•
Rate per
Minute Climber
•
<blank> - Bike,
Treadmill
Lower Display
Workouts
The Muscle Monitor displays the
muscles used to perform that
workout.
Stride Length describes the
length of your steps during a
workout.
Rate per Minute displays the
number of meters, feet, or steps
that a user has gained during a
workout.
Displays graphical information about
your workout progress
•
Manual
•
Heart Rate
•
Interval
•
Weight Loss*
•
Variety*
•
Performance*
•
Fat Burner - older model AMT
only
* Not available on older model AMT
Quick Start
Press to begin exercising
19
Getting Started
Number Part Name
Options
Details
•
•
Press to enter Goals, Language,
Weight, Age, and Target Heart
Rate information, More Options
Press More Metrics to view
additional metric information
Metrics:
•
Percent Complete
•
Time in Zone
•
Segment Time Remaining
•
Average Speed
•
Pace - Treadmill only
•
Calories per Minute
•
Calories per Hour
•
WATTS
•
METS
•
Target HR
•
Average HR
•
Elevations - Treadmill and
climber only
•
Stride Length - AMT only
•
Show All
•
OFF
Note: If your AMT has a Metrics
key, press that key to view your
metrics information.
Back
Returns user to the previous screen
Pause
For Treadmills: Pauses treadmill
during a workout.
For Self-powered Equipment:
Functions as a reset key. Pressing it
stops the workout program and
displays the workout summary.
OK and Up/Down
arrows
Use to navigate options and settings
Speed or Intensity
Indicator
AMT, AMT with Open Stride ,
bike, treadmill, EFX (single), and EFX
(dual)
TM
20
Operating and Maintaining the P30 Console
Number Part Name
Details
Incline or
Resistance
Indicator
Treadmill, EFX (dual), climber, and
TM
AMT with Open Stride
Number pad
Use to enter numerical information
such as age, weight, and passwords.
Press Clear to delete the numbers
entered.
Press Enter after you have entered
numbers on this number pad.
Chapter
2
Setting Up the Console
Use the System mode to configure settings in ways that
benefit your users and your facility. The System menu is
visible only to administrators and registered service
technicians. Changes made to these settings are saved to the
fitness equipment.
The System Settings categories are:


Club Settings
Informational Display
System Settings
System Setting features remain hidden from club patrons and
can only be accessed using special keypresses. To view the
System Settings, the equipment must be in the Welcome
state and display the Welcome banner. To access the
Welcome banner, you must power the equipment. For
self-powered equipment, use the optional power adapter,
otherwise you will have to maintain the minimum rate of
motion. For more information on self-powered equipment,
refer to Activating the Console for Self-Powered Equipment.
22
Operating and Maintaining the P30 Console
The equipment is in the Welcome state when it is on, but not
actually in use. This means that there is no exercise session,
data entry, or diagnostic operation in progress.
When the equipment is in the Welcome state:
PRECOR scrolls on the lower text display. SELECT A
WORKOUT OR PRESS QUICKSTART TO BEGIN scrolls
in the upper text display.
 The heart rate signal is the only segment activated.
 On the treadmill, the belt is not moving and the lift motor
is off.
Note: On self-powered equipment, the console initializes
when you begin working out. You must maintain a minimum
rate of motion for the Welcome banner to appear.

The changes made in System Setting modes become the
default settings when the display resets to the Welcome
banner.
CAUTION: If you change the Unit of Measure display on the
treadmill, check the speed setting to verify that it is correct.
To view the Club Parameters settings:
1. At the Welcome banner, press Pause.
2. Press the following number keys in sequence to enter the
password:
5651565
3. Press OK.
The Set Club Parameters banner appears.
Table 2. Navigational keys for the system setting modes
Key
Function
▲ or ▼
Navigates the settings menu
OK
Selects a menu setting
BACK
Returns to the previous menu level without saving
changes
PAUSE
Exits the System Settings mode and returns to the
Welcome banner
Setting Up the Console
23
Setting Club Parameter Values
Use this information to customize the equipment for your
setting.
Safety Code (Treadmill only)
Value Range: Enabled or Disabled
(Default: Disabled)
When the equipment is shipped from the factory, the safety
code protection feature is disabled. If you enable the safety
code, your users will need to enter a four digit number to
begin their exercise session and start the running belt. The
code is 1 2 3 4.
Select Language (All Equipment)
Value Range: English, Deutsch, Espanol, Francais,
Netherlands, Portugues, Rucckijj, and Italiano
(Default: English)
Select your preferred language for the console display.
Note: Programming prompts are not affected by language
selection. The prompts in this section continue to appear in
English.
Set Units (All Equipment)
Value Range: U.S. or Metric
(Default: U.S.)
The equipment can display measurements in either Metric or
U.S. Standard.
Important: If you change the Unit of Measure on a treadmill, be
sure to check the speed setting to verify that it is correct.
24
Operating and Maintaining the P30 Console
Set Max Workout Time (All Equipment)
Value Range: 1 to 240 minutes
(Default: 60 minutes)
You can set a maximum workout time per session. Choose a
time limit between 1 and 240 minutes, or select No Limit if
you do not want to set a time limit. For example, if you set the
time limit to 20 minutes, users can only enter a workout time
between 1 and 20 minutes.
Select No Limit if you do not want to set a time limit.
Note: The Military Performance Programs will not complete if
the maximum exercise time limit is less than 40 minutes. Set
the maximum time about 40 minutes if you have enabled
these performance programs.
Set Max Pause Time (All Equipment)
Value Range: 1 to 120 seconds
(Default: 120 seconds)
This setting limits how long equipment remains in a paused
banner during a workout before it resets.
Note: The optional power adapter must be connected on
self-powered equipment to establish a definitive pause time
limit. If the optional power adapter is not attached and the
rate of motion drops below the minimum requirements, the
equipment begins its 30-second shutdown, effectively
eliminating pause mode.
Set Cool Down Time (All Equipment)
Value Range: 0 to 5 minutes
(Default: 5 minutes)
Select the maximum amount of time the equipment remains
in the cool down mode. The cool down time is the period of
time following the completion of a program when the user
exercises at a reduced work rate.
25
Setting Up the Console
Creating a Custom Workout
Value Range: ON or OFF
(Default Value: OFF)
Create a customized program for your workout.
Note: This option is not available on all equipment.
To create a custom program:
1. At the SET CUSTOM PROGRAM prompt, press OK.
The program profile appears in the display and a blinking
column indicates your starting point.
2. Press the down arrow key on the navigational keypad to
select the column you want to change.
3. To change the height of the column, refer to the following
table.
Table 3. Custom Program keys
Equipment
Key Name
Description
Treadmill
INCLINE
Changes the column height and affects
the Custom Program incline.
EFX (835
only)
INCLINE
Changes the column height and affects
the Custom Program ramp incline.
Bike
RESISTANCE Changes the column height and affects
the Custom Program pedal resistance.
Climber
RESISTANCE Changes the height of the column and
affects the Custom Program step
resistance.
4. When you have set the column height, press the down
arrow key on the navigational keypad to move to the next
column. You can press the up arrow key to return to
previous columns.
5. Continue adjusting the profile for each column.
Note: Two custom programs are available on the
treadmill. Some Precor products contain only one custom
program. The prompt indicates which one you have
accessed. To select a second custom program (treadmill
only), press the down arrow key on the navigational
keypad, before pressing OK in step 6.
The Set Custom Program 2 default value is Disabled.
26
Operating and Maintaining the P30 Console
6. When you have finished creating your program, press OK
to save the program profile, and return to the Welcome
banner. Press BACK, to exit this setting without saving
your changes to the custom profile.
Set Speed Limit (Treadmill only)
Value Range: Full speed range of equipment
(Default: Maximum speed)
This setting limits how fast the running belt moves and,
consequently, the number of speed settings that are available
to the user. Use it to set the maximum speed that a user can
enter when using the equipment.
The speed is displayed in miles per hour (mph) or kilometers
per hour (kph) depending upon the units of measure (U.S.
Standard or Metric) selected earlier. The speed ranges values
from 0.5 to 16 mph (0.8 to 25.5 kph).
Set Incline Limit (Treadmill only)
Value Range: Full grade range of equipment
(Default: Maximum grade possible)
Set the maximum percent incline that a user can enter when
using the equipment.
Hidden Programs (Treadmill only)
Value Range: Show Programs or Hide Programs
(Default: Hide Programs)
When set to Show Programs, all Performance Programs are
available to a user through the PERFORMANCE key. These
programs are: Gerkin Fitness Test, USAF PRT, NAVY PRT,
ARMY PFT, USMC PFT, and Federal Law Enf. PEB.
If set to HIDE PROGRAMS, when the user presses
PERFORMANCE, the message WORKOUT NOT AVAILABLE
will scroll in the upper text display.
27
Setting Up the Console
Set Resistance Range (Bike only)
Value Range: High, Medium, or Low
(Default: High)
You can set a low, medium, or high base resistance on the
recumbent or upright bikes. There are 25 levels of resistance
within each base setting, but the base setting affects the
overall resistance range. The following ranges are available:



High: Provides full resistance range.
Medium: Provides approximately two thirds of the
resistance that is available within the high group setting.
Low: Provides approximately one third of the resistance
that is available within the high group setting.
Set Crossramp Auto Level (EFX Dual only)
Value Range: 0 to 20
(Default: 10)
Use this setting to choose a specific ramp incline so that the
EFX automatically returns to that incline at the end of a
workout session.
28
Operating and Maintaining the P30 Console
Viewing the Informational Displays
Information Display settings are values that provide you with
information about the equipment. Types of information
contained in this setting group include, an event log, software
and equipment serial numbers, and usage information.
To view the System settings:
1. At the Welcome banner, press Pause.
2. Press the following number keys in sequence to enter the
password:
65
3. Press Enter.
Use the following table to set up customized Informational
Display values.
Table 4. Informational Displays values
Product Value
Information provided
All
The odometer value correlates to the
type of equipment and the standard
of units, U.S. or Metric, selected in
the programs.
ODOMETER
•
•
•
•
Treadmill and newer model AMT:
Displays the number of
cumulative miles or kilometers
logged to date. In addition, the
AMT displays the number of
vertical strides.
EFX: Displays the number of total
strides logged to date.
Bike: Displays the number of total
revolutions logged to date.
Climber: Displays the number of
floors climbed.
29
Setting Up the Console
Product Value
AMT - BELT USAGE
Newer
Models
Only
Information provided
•
•
•
All
HOUR METER
•
•
Belt Stride Count: Tracks the
number of strides on equipment.
Stride Count Reset: Reset
increases by one each time a
reset is performed.
Odometer at Last Reset: Records
the odometer reading at the time
the belt was changed. The
equipment odometer continues to
count forward after the belt
change.
Displays the number of hours that
the equipment has been in use.
The equipment tracks the elapsed
minutes, but the value that
appears is truncated to the
nearest full hour.
All
UPPER BOOT SW
PART NUMBER
Upper board application software
part number and version
All
UPPER BASE SW
PART NUMBER
Upper base application software
version
All
LOWER BASE SW Lower application software version
PART NUMBER
All
METRICS BOARD
Software number on the Metrics
Board
AMT
STRIDE DIAL SW
PART NUMBER
Stride Dial software number
All
SERIAL NUMBER
Used to determine exact model and
type of equipment
All
USAGE LOG
•
•
All
EVENT LOG
The number of times each
program has been used and
displays the associated
cumulative minutes.
Helpful in determining user
preferences in program selection.
Displays any event codes that may
have been detected by the software.
For more information, refer to Event
Log.
30
Operating and Maintaining the P30 Console
Event Log
The event log holds a maximum of 30 events. After the log
reaches 30 events, older events are erased to make room for
newer ones.
Each event log entry contains the following information:
Event number
Odometer value when the event occurred
Hour meter value at the time the event occurred
Current drawn by the motor when the event occurred
(treadmill only)
The following table contains a list of events detectable by the
software.




Table 5. Event log numbers and descriptions
Event
Description of Event
Number
00
Upper PCA memory location event
02
RAM location event
03
EEPROM checksum event
05
Depressed key at power up
09
Lower PCA memory test event
10
Line Frequency out of acceptable range
11
Watchdog (Upper PCA) low voltage power
12
Watchdog (Lower PCA) low voltage power
13
Fan at incorrect speed (version 1 treadmills)
14
Fan fail (Lower PCA)
15
AC input voltage too high
16
AC input voltage too low
20
Too many maximum power requests in one second
21
Too many maximum consecutive power requests
22
No motor pulses at start up
23
Motor pulses missing after start up
24
Reduce speed requested, speed is not reducing
26
Motor pulse width incorrect
27
Too much drive motor current
28
Temperature too high
31
Setting Up the Console
Event
Description of Event
Number
29
Excessive AC input current
30
Communications event lower board to upper board
31
Incorrect Communications event upper board to lower
board
32
Communication event upper board to lower board
33
Incorrect communications event lower board to upper board
37
E-STOP error (treadmill only)
40
Lift motion detected
42
Lift position value out of range
43
Zero switch not found
44
Un-commanded lift motion
45
Lift going in the wrong direction
50
Too much brake (magnet) current
53
Cannot read target, cannot find home switch
54
Target pulses lost during operation
55
Brake home switch activated unexpectedly
60
Auto Stop sensor failure (treadmill only)
61
Auto Stop not present (treadmill only)
62
Vertical sensor failure (AMT only)
70
Belt replacement, lower control board not read (AMT only)
71
Belt replacement, new lower control board (AMT only)
72
Belt replacement, lower control board version unknown
(AMT only)
73
Belt replacement, lower control board record bad (AMT
only)
74
Belt replacement, lower control board refurbished console
(AMT only)
75
Belt replacement, refurbished lower control board (AMT
only)
76
Belt replacement, console stride count is less than lower
control board (AMT only)
77
Belt replacement, console stride count is greater than lower
control board (AMT only)
78
Belt replacement warning (AMT only)
79
Belt replacement required (AMT only)
32
Operating and Maintaining the P30 Console
User ID Entry with CSAFE Equipment
This equipment is fully compatible with CSAFE protocols.
When the equipment is connected to a CSAFE master device,
the user is prompted to press ENTER and begin an
identification process. The user ID is displayed as five zeros
and indicates the starting point. The following table describes
key functions while in CSAFE mode.
Table 6. CSAFE access keys
Keys
Function
Number
Keypad
Use the number keys to enter a user ID. Once you have
entered the user ID number, press ENTER or OK to
submit the user ID.
CLEAR
Erases individual numbers in the user ID from right to
left.
ENTER or
OK
Submits the user ID.
PAUSE
Resets to the Welcome banner.
Note: User ID entry is bypassed when the user enters
five zeros. No workout statistics are recorded.
A message appears on the display and indicates when the
user ID is accepted by the CSAFE master device. Once
program selection is complete, the user can begin exercising.
Chapter
3
Introducing Users to the P30
Console
CAUTION: Before beginning any fitness program, see your
physician for a thorough physical examination. Seek advice from
your physician to learn the target heart rate appropriate for your
fitness level.
The P30 console offers an easy-to-follow display and multiple
programs to help people meet their exercise needs.
Important: Please review the following sections in this guide with
your users before allowing them to use the fitness equipment:



Important Safety Instructions
Getting Started
Using the Safety Clip (for treadmill only)
Using the Touch Heart Rate Feature
Note: Touch heart rate performance may vary based on a
user’s physiology, fitness level, age, and other factors. You
may experience an erratic readout if your hands are dry, dirty,
or oily, or if the skin on your palms is especially thick. Wearing
hand lotion can also cause an erratic readout. In addition,
make sure that the sensors are clean to ensure proper contact
can be maintained.
To use the touch heart rate feature, place the palm of your
hands directly on the metal heart rate sensors on the
equipment’s handlebars. To ensure an accurate heart rate
readout, make sure you follow these tips:


Both hands must grip the sensors for your heart rate to
register.
It takes a number of consecutive heartbeats (15-20
seconds) for your heart rate to register.
34
Operating and Maintaining the P30 Console



When gripping the sensors, do not grip tightly. Keep a
loose, cupping hold. Holding the grips tightly can affect
the reading.
As you work out, your perspiration will help transmit your
heart rate signal. If you have difficulty using the handheld
grips to determine your heart rate, try the sensors again
later in the workout to see if you can obtain a heart rate
signal.
If the touch heart rate feature does not work for you,
Precor recommends that you use a chest transmitter
strap.
Figure 5: Heart rate target zones
CAUTION: Your heart rate should never exceed 85% of your
maximum aerobic heart rate. Your maximum heart rate is equal to
220 minus your age.
35
Introducing Users to the P30 Console
Using a Chest Strap Transmitter
WARNING Signals used by the Chest Strap Transmitter
(or heart rate strap) may interfere with
pacemakers or other implanted devices.
Consult your physician and the manufacturers
of your Chest Strap Transmitter and implanted
device before using a Chest Strap Transmitter.
Wearing a chest strap transmitter during your workout
provides steady heart rate information. For the equipment to
detect your heart rate, you must grip the touch heart rate
sensors or wear a chest strap transmitter while exercising. In
the presence of both touch and wireless data, the touch data
takes precedence and will display.
Note: To receive an accurate reading, the strap needs to be in
direct contact with the skin on the lower sternum (just below
the bust line for women).
To use a chest strap transmitter:
1. Carefully dampen the back of the strap with tap water.
Important: Do not use deionized water. It does not have the
proper minerals and salts to conduct electrical impulses.
2. Adjust the strap and fasten it around your chest. The
strap should feel snug, not restrictive.
3. Make sure that the chest strap is right-side-up, lies
horizontally across, and is centered in the middle of your
chest.
4. Test the chest strap placement by checking the heart rate
function on the equipment. If a heart rate is registering,
your chest strap placement is correct. If the equipment
does not register a heart rate, readjust the strap and
recheck the heart rate function.
36
Operating and Maintaining the P30 Console
Using the Treadmill Safety Clip
The treadmill is equipped with two different stop functions,
which behave as follows:
If the user …
Then the
And the console …
treadmill belt …
Presses down on the red Slows to a stop Shows that the exercise
STOP button
workout is paused
Pulls on the lanyard
Slows to a stop
attached to the safety
clip and trips the restart
switch
Shows the words PUSH
TO RESET SWITCH and
an arrow pointing to the
Restart switch
The restart switch is located just below the console and
immediately behind the red STOP button, as shown in the
following figure. When it is tripped, the bar pops up,
displaying the words PUSH TO RESET SWITCH on its front
side. The treadmill does not operate while these words are
visible.
Figure 6: Restart switch
Instruct users on how important it is to use the safety clip
while exercising on the treadmill, and demonstrate how they
should attach it to their clothing near the waistline.
Introducing Users to the P30 Console
37
If the restart switch trips during exercise, perform the
following steps:
1. Reattach the safety clip if necessary.
2. Press the restart switch down until it clicks, returning it to
its normal position.
Note: If the restart switch trips, all information about the
current workout is deleted.
3. Start the workout from the beginning, reducing the time
as needed to account for the amount of exercise that has
been completed.
Figure 7: Attaching the safety clip
38
Operating and Maintaining the P30 Console
Treadmill Auto Stop™ (Automatic Stop)
Function
Important: The default setting for this feature is ON. An
administrator can turn off this feature in the System Settings;
however, Precor recommends it remain ON.
The Auto Stop™ (Automatic Stop) feature is designed to
bring the treadmill to a gradual stop when it is not in use. This
might occur if a user steps off the treadmill before the end of
a workout and leaves the treadmill running.
Sixty seconds after a treadmill workout starts or resumes, the
equipment begins Auto Stop monitoring. If a user is detected,
then no message appears, and the selected workout
continues.
If no user is detected after an additional 30 seconds, the
console displays the message NO USER DETECTED,
STOPPING IN 10 SECONDS as notification of the pending
stop. During the display of this message, a ten second
countdown begins. If a user does not override the countdown,
the belt comes to a gradual stop after the countdown is
complete.
Note: Users weighing more than 90 pounds (41 kg) are
detected within the speed and position limits of the feature.
Users weighing 50 pounds (22.7 kg) to 89 pounds (40.5 kg)
may not be detected depending on their speed and location.
Always be aware of and follow the console’s instructions for
proper operation.
Chapter
4
Starting a Workout
CAUTION: If you are using a treadmill, be sure to attach the
security clip to your clothing before starting your workout.
The equipment is in the Welcome state when the words
SELECT A WORKOUT OR PRESS QUICKSTART TO BEGIN
scroll across the scrolling upper text display and PRECOR
scrolls on the lower text display.
If the equipment is connected to CSAFE, the words SELECT A
WORKOUT, PRESS QUICKSTART, OR ENTER TO BEGIN
scroll across the upper text display.
If anything else appears on the screen, press Pause to display
the Welcome banner.
From this screen, there are two ways to begin a workout:
Press Quick Start™.
This action launches the Manual program. Calculations,
such as calories used, are based on a 150-lb (68 kg),
35-year old individual. You can complete a workout using
this program with default values, or you can change
workout settings.
 Press one of the preset workouts.
When a user reaches the club time limit during a workout, the
workout limit in minutes appears before the words CLUB
TIME LIMIT REACHED, WORKOUT ENDING, appear in the
upper text display.

40
Operating and Maintaining the P30 Console
Starting a Preset Programmed Workout
Preset workouts are a great way to tailor your workouts to
your fitness goals, stay challenged, and add variety to your
sessions. Most P30 equipment contains multiple preset
workouts. These workouts include:
Manual
Heart Rate
Interval
Weight Loss (Fat Burner on older model AMT)
Variety
Performance
Climber-specific programs are:











City Steps
Fat Burn
Rolling Hill
Steady Climb
Pyramid
Setting Options
Goal, Language, and Unit options can be set before you begin
a workout. Once you begin a workout or press Quick Start,
you can also enter Age and Weight, and a Target Heart Rate
goal.
Note: After setting personal options, select a workout and
begin exercising or your options will revert to the default
values.
To choose a workout goal before you begin exercising:
1. From the Welcome banner, press OPTIONS.
Goal is the first option.
2. To choose the Goal option, press OK.
Goal options are Time, Distance, and Calories.
3. Use the Up and Down arrows or keypad to increase or
decrease your time, distance, or calorie goal.
4. Once you have entered a goal, press OK.
5. To continue to the next option category, Press OPTIONS
again.
41
Starting a Workout
To choose a language setting before you begin exercising:
1. From the Welcome banner, press OPTIONS.
2. Press OPTIONS again to choose the Language option, and
press OK.
3. Use the Up and Down arrows to navigate the list of
available languages. To select a language, press OK.
Language choices are: English, Deutsch, Espanol, Francais,
Nederlands, Portugues, Rucckijj, and Italiano.
4. To continue to the next option category, press the Up or
Down arrows.
To choose a unit of measure before you begin exercising:
1. From the Welcome banner, press OPTIONS.
2. Press OPTIONS twice to go to UNITS.
3. Use the Up and Down arrows to select a unit of measure.
4. Once you have selected a unit of measure, press OK.
Setting Options after You Begin a Workout
Once you begin a Quick Start workout or choose a Workout,
you can enter your Weight and Age, and a Target Heart Rate
goal. The Language and Units settings are also available.
To enter your Age and Weight during a workout:
1. Press OPTIONS.
2. Weight/Age is the first option. To choose this option,
press OK.
3. Use the Up and Down arrows to increase or decrease
your weight.
4. Once you have selected your weight, press OK.
5. Repeat steps 1 - 4 to enter your age.
6. To continue to the next option category, press the Up or
Down arrows.
The Target Heart Rate option appears.
7. Enter a target heart rate goal, and press OK.
At this time, you can set Units and Language if you have
not selected these options prior to beginning your
workout.
42
Operating and Maintaining the P30 Console
Pausing and Resuming an Exercise Session
When you interrupt a workout, the equipment responds in
one of two ways, depending on how it is powered.
Paused (Externally Powered Equipment)
When the session is paused, the belt speed is slowly reduced
to zero, or the resistance is slowly reduced to the minimum.
The lift motor is turned off leaving the incline or crossramp at
its current position. Data entry is canceled.
When you press Pause on all non-treadmill equipment, it
displays the summary screen with your workout metrics.
After displaying the summary, it returns to the Welcome
screen.
Pending Shutdown (Self-Powered Equipment)
On self-powered machines, the paused state is equivalent to
the pending shutdown state. When you stop working out, the
equipment begins a 30 second countdown.
The accumulated metrics (e.g., time, strides, distance,
calories) hold their current values and do not change. Data
entry may not be started.
To restart the program, begin working out again. The
resistance is reset to what it was when the program was
paused.
If the equipment remains inactive for more than 30 seconds,
the power is lost and the equipment bypasses the workout
summary screen.
Ending a Session
Cooling down is an important aspect of your workout because
it helps reduce muscle stiffness and soreness by transporting
excess lactic acid out of the working muscles. In addition, a
three to five minute cool down allows your heart rate to
return to its normal, resting state.
At the end of your workout, a Summary screen displays your
average heart rate during your workout and your accumulated
workout metrics.
43
Starting a Workout
If you performed a fitness test exercise program, an initial
message presents a fitness score.
The next two messages display the user’s average and
maximum heart rate during the session. These messages are
only displayed if heart rate data was acquired during the
session, i.e., a valid heart rate number was displayed at least
once during the session.
The summary state times out in two minutes, causing a return
to the Welcome banner. If the machine is in a CSAFE Finished
state then the summary state must last for at least the CSAFE
timeout value, typically 10 seconds. If it has not lasted that
long, then before returning to the Welcome banner, the word
RESETTING appears until the CSAFE finished state ends.
Three different types of metrics are captured during a
workout.
Controlled Metrics can be set and changed. They include:
Resistance Level (AMT, EFX, bike)
Speed (treadmill)
Incline (treadmill)
Steps/Minute (climber)
Current Performance Metrics describe the intensity of a
workout in real time. They include:




Calories/Minute, Calories/Hour
Heart Rate
Speed (treadmill, bike)
Revolutions/Minute (bike)
Strides/Minute (AMT, EFX)
Accumulated Metrics describe the overall performance
throughout the entire exercise session. They include:








Time:
Count-down Mode
Count-up Mode
Calories
Distance:
Average Strides/Minute (AMT, EFX)
Average Speed (treadmill, bike)
Floors (climber)
44
Operating and Maintaining the P30 Console
Programs
Preset workouts are a great way to tailor your workouts to
your fitness goals, stay challenged, and add variety to your
sessions. In the following figures, the elevated areas show the
work expenditure for each preset program.
Manual
During this workout, resistance and speed changes are
completely under your control. The profile is initially a flat
line. Any increase or decrease made in one workout segment
will increase or decrease all remaining portions by the same
amount.
Heart Rate
This workout computes your target heart rate based on the
calculation, 60% of 220 minus your age; however, you can
override this value. The equipment adjusts resistance and/or
incline to maintain your target heart rate while you work out.
When a heart rate signal is not received, a heart shape with a
question mark appears in the upper text display. On the
newer model AMT, the heart shape remains lit, but the metric
display appears blank. Recheck your hand grip on the
handheld sensors or the placement of your chest strap.
For the unit to detect your heart rate, you must grip the
handheld heart rate sensors or wear a chest strap while
exercising. In the presence of both handheld and wireless
data, the handheld data takes precedence and displays.
Interval
The Interval workout is primarily for conditioning your
cardiovascular system. This workout is designed to raise and
lower your heart rate in a repeating fashion for a user-defined
period of time by alternating rest and work intervals. Workout
intensity is adjustable.
Weight Loss
The workout time is fixed at 28 minutes. The workout
consists of seven four-minute intervals. You can change the
resistance at any time during the work interval.
Note: This program is called Fat Burner on older AMT
models.
45
Starting a Workout
Variety
During this workout, resistance or ramp/incline vary
throughout the workout in a random pattern.
Performance
Note: When a user presses PERFORMANCE, the message
WORKOUT NOT AVAILABLE will scroll in the upper text
display, if the console is set to HIDE PROGRAMS in the
Settings menu.
The Fitness Test, available by pressing the PERFORMANCE
key, provides a means of comparing your fitness level with the
official fitness test of the International Association of
Firefighters (IAFF). It is written using the Gerkin Protocol,
which is the basis for the official IAFF fitness test and part of
their Wellness and Fitness Initiative.
During the test, the equipment gradually increases the incline
and speed in specific stages. The keypads are disabled.
Whatever stage you are at when the test ends determines
your aerobic capacity and establishes your VO2 max. Once
you complete the test, a fitness score appears as part of the
workout summary.
City Steps (Climber only)
The City Steps Program increases and decreases your step
rate in stages. In each stage, the rate gradually rises to a peak
and then falls quickly back to the starting rate. This pattern is
repeated. You can override the settings for each column. Any
increase or decrease made in one program segment will
increase or decrease all remaining portions by the same
amount.
Fat Burn (Climber only)
This intense program is designed to burn fat and increase
cardiovascular conditioning. Step rate fluctuates mildly within
a high-intensity range. Anytime during the program, you can
override the settings, and the remaining profile columns will
change accordingly. The changes are applied throughout the
remainder of the program.
46
Operating and Maintaining the P30 Console
Rolling Hill (Climber only)
This cardio-conditioning program provides a high step rate.
Like the Aerobic program, it involves several “peaks” and
“valleys” in step rate; however, the dips in intensity during
“rest” periods are smaller, resulting in more consistent
intensity. You can override the settings for each column. The
changes also raise or lower the columns on the remaining
portion of the program profile.
Steady Climb (Climber only)
The Steady Climb program slowly increases the step rate until
it culminates at the end of the program. You can override the
settings for each column. The changes also raise or lower the
columns on the remaining portion of the program profile.
Pyramid (Climber only)
The Pyramid Program slowly increases the step rate to a
“peak” and then slowly decreases back to a slower rate. As
the step rate increases, resistance is decreased and then
increases as the step rate decreases. Any increase or
decrease made in one program segment will increase or
decrease all remaining portions by the same amount.
Chapter
5
Maintenance
To keep the equipment functioning properly, perform the
minor maintenance tasks in this section at the intervals
suggested. Failure to maintain the equipment as described in
this section could void the Precor Limited Warranty.
DANGER
To reduce the risk of electrical shock, always
disconnect the equipment from its power source
before cleaning it or performing any maintenance
tasks. If the equipment uses an optional power
adapter, disconnect the adapter.
Cleaning the Console and Display
The console requires little maintenance once installed. Precor
recommends that you clean the console before and after each
exercise session.
To remove dust and dirt from the console:
 Wipe all exposed surfaces with a soft cloth that you have
moistened with a solution of 30 parts of water to 1 part of
Simple Green® (for more information, visit
www.simplegreen.com).
Important: Do not use any acidic cleaners. Doing so will weaken
the paint or powder coatings and void the Precor Limited
Warranty. Never pour water or spray liquids directly on the
console or console’s screen.



It is important to avoid using any corrosive chemicals on the
console or screen.
Always dampen the cloth and then clean the screen. Be sure
to spray the cleaning liquid onto the cloth, not the console, so
that drips do not seep into the console.
Apply the cleaner with a soft, lint-free cloth. Avoid using gritty
cloths.
48
Operating and Maintaining the P30 Console
Changing the Belt (Newer Model AMT Only)
The newer model AMT uses belts to provide motion. These
belts eventually wear and must be replaced.
When the belt stride count reaches 90 million, the message
BELTS MUST BE CHANGED SOON scrolls on the Welcome
screen. While this message appears, the AMT operates
normally.
Important: If this message displays on your AMT, please contact
Precor Customer Support for assistance.
When the belt stride count reaches 100 million (and the belt
has not been changed), the message BELTS CHANGE
REQUIRED scrolls continuously on the Welcome screen. The
input keys are not functional and the user cannot enter values
or begin a workout until the belts are changed. Please contact
Precor Customer Support to schedule a belt change.
Operating and Maintaining
the P30 Console
Precor Incorporated
20031 142nd Avenue NE
P.O. Box 7202
Woodinville, WA USA 98072-4002
P30 OM 301096-301 rev E, en
December 2012
Assembling and Maintaining
Elliptical Fitness Crosstrainers™
EFX® 883 • EFX® 833
Precor Incorporated
20031 142nd Avenue NE
P.O. Box 7202
Woodinville, WA USA 98072-4002
EFX 8x3 PAG/OM 300712-401 rev H, en
Warranty #36286-114
October 2012
Edition Information
ASSEMBLING AND MAINTAINING ELLIPTICAL FITNESS
CROSSTRAINERS: EFX 883 / 833
P/N 300712-401 rev H
Copyright © October 2012 Precor Incorporated. All rights
reserved. Specifications subject to change without notice.
Trademark Note
Precor, AMT, EFX, and Preva are registered trademarks of
Precor Incorporated. Other names in this document may be
the trademarks or registered trademarks of their respective
owners.
Intellectual Property Notice
All rights, title, and interests in and to the software of the
Preva Business Suite, the accompanying printed materials,
any copies of such software, and all data collected via the
Preva Business Suite, are exclusively owned by Precor or its
suppliers, as the case may be.
Precor is widely recognized for its innovative, award-winning
designs of exercise equipment. Precor aggressively seeks U.S.
and foreign patents for both the mechanical construction and
the visual aspects of its product design. Any party
contemplating the use of Precor product designs is hereby
forewarned that Precor considers the unauthorized
appropriation of its proprietary rights to be a very serious
matter. Precor will vigorously pursue all unauthorized
appropriation of its proprietary rights.
Precor Incorporated
20031 142nd Ave NE, P.O. Box 7202
Woodinville, WA 98072-4002
1-800-347-4404
http://www.precor.com
Important Safety Instructions
Important: Save these instructions for future reference.
Read all instructions in the documentation provided with your
exercise equipment, including all assembly guides, user
guides, and owner’s manuals, before installation of this
device.
Note: This product is intended for commercial use.
The display apparatus (hereinafter referred to as the console)
is intended to be shipped with new Precor exercise equipment
(hereinafter referred to as the base unit). It is not packaged for
individual sale.
WARNING
To prevent injury, the console must be
attached securely to the base unit following all
assembly and installation instructions shipped
with the base unit. The console is intended to
be connected to AC mains power through the
furnished power supply ONLY. It should be
powered on only when installed as described
in the assembly and installation instructions
shipped with the base unit. The console is
intended for use only with Precor fitness
equipment, not as a standalone device.
4
Assembling and Maintaining Elliptical Fitness Crosstrainers: EFX 883 / 833
Safety Precautions
Always follow basic safety precautions when using this
equipment to reduce the chance of injury, fire, or damage.
Other sections in this manual provide more details of safety
features. Be sure to read these sections and observe all safety
notices. These precautions include the following:






Read all instructions in this guide before installing and
using the equipment and follow any labels on the
equipment.
Make sure all users see a physician for a complete
physical examination before they begin any fitness
program, particularly if they have high blood pressure,
high cholesterol or heart disease; have a family history of
any of the preceding conditions; are over the age of 45;
smoke; are obese; have not exercised regularly in the past
year; or are taking any medication.
French equivalent of the above notice, for Canadian
markets: Il est conseillé aux utilisateurs de subir un examen
médical complet avant d’entreprendre tout programme
d’exercice, en particulier s’ils souffrent d’hypertension
artérielle, ou de cardiopathie ou ont un taux de cholestérol
élevé, s’ils ont des antécédents familiaux des précédentes
maladies, s’ils ont plus de 45 ans, s’ils fument, s’ils sont
obèses, s’ils n’ont pas fait d’exercices réguliers au cours de
l’année précédente ou s’ils prennent des médicaments. Si vous
avez des étourdissements ou des faiblesses, arrêtez les
exercices immédiatement.
Do not allow children, or people unfamiliar with the
operation of this equipment, on or near it. Do not leave
children unsupervised around the equipment.
Make sure all users wear proper exercise clothing and
shoes for their workouts and avoid loose or dangling
clothing. Users should not wear shoes with heels or
leather soles, and they should check the soles of their
shoes to remove any dirt and embedded stones. They
should also tie long hair back.
Never leave the equipment unattended when it is plugged
in. Unplug the equipment from its power source when it is
not in use, before cleaning it, and before providing
authorized service.
Note: The optional power adapter is considered a power
source for self-powered equipment.
Use the power adapter provided with the equipment. Plug
the power adapter into an appropriate, grounded power
outlet as marked on the equipment.
Important Safety Instructions








Care should be taken when mounting or dismounting the
equipment.
For Treadmills: Do not use typing or web surfing features
while walking at speeds that exceed a slow and relaxed
leisurely pace. Always stabilize yourself by holding a
stationary handle bar while using typing or web surfing
features.
For AMT and EFX: Always stabilize yourself by holding a
stationary handle bar while using typing or web surfing
features.
Read, understand, and test the emergency stop
procedures before use.
Keep the power cord or optional power adapter and plug
away from heated surfaces.
Route power cables so that they are not walked on,
pinched, or damaged by items placed upon or against
them, including the equipment itself.
Ensure the equipment has adequate ventilation. Do not
place anything on top of or over the equipment. Do not
use on a cushioned surface that could block the
ventilation opening.
Assemble and operate the equipment on a solid, level
surface.
5
6
Assembling and Maintaining Elliptical Fitness Crosstrainers: EFX 883 / 833






SPACING—The below minimum spacing
recommendations are based on a combination of the
ASTM (U.S.) voluntary standards and EN (European)
regulations as of October 1, 2012, for access, passage
around, and emergency dismount:
 Treadmills—a minimum of 0.5 m (19.7 in.) on each
side of the treadmill and 2 m (78 in.) behind the
machine.
 Cardio equipment other than treadmills—a
minimum of 0.5 m (19.7 in.) on at least one side, and
.5 m (19.7 in.) behind or in front the machine.
Careful consideration should be given to the
requirements of the Americans with Disabilities Act
(ADA), US Code 28 CFR (see Section 305). ASTM
standards are voluntary and may not reflect current
industry standards. The actual area for access, passage
around, and emergency dismount is the responsibility of
the facility. The facility should consider the total space
requirements for training on each unit, voluntary and
industry standards, and any local, state, and federal
regulations. Standards and regulations are subject to
change at any time.
Important: These spacing recommendations should be used
when positioning equipment away from sources of heat, such
as radiators, heat registers, and stoves. Avoid temperature
extremes.
Keep equipment away from water and moisture. Avoid
dropping anything on or spilling anything inside the
equipment to prevent electric shock or damage to the
electronics.
When using the treadmill, always attach the safety clip to
your clothing before beginning your workout. Failure to
use the safety clip may pose a greater risk of injury in the
event of a fall.
Keep in mind that heart rate monitors are not medical
devices. Various factors, including the user’s movement,
may affect the accuracy of the heart rate readings. The
heart rate monitors are intended only as exercise aids in
determining heart rate trends in general.
Do not operate electrically powered equipment in damp
or wet locations.
Never operate this equipment if it has a damaged cord or
plug, if it is not working properly, or if it has been dropped,
damaged, or exposed to water. Call for service
immediately if any of these conditions exist.
Important Safety Instructions










7
Maintain the equipment to keep it in good working
condition, as described in the Maintenance section of the
owner’s manual. Inspect the equipment for incorrect,
worn, or loose components, and then correct, replace or
tighten prior to use.
If you plan to move the equipment, obtain help and use
proper lifting techniques.
Equipment Weight Restrictions: Do not use the treadmill
if you weigh more than 500 pounds (225 kg). If you weigh
more than 350 pounds (160 kg), do not run on the
treadmill. For all other fitness equipment, the weight limit
is 350 pounds (160 kg).
Use the equipment only for its intended purpose as
described in this manual. Do not use accessory
attachments that are not recommended by Precor. Such
attachments may cause injuries.
Do not operate the equipment where aerosol (spray)
products are being used or where oxygen is being
administered.
Do not use outdoors.
Do not attempt to service the equipment yourself, except
to follow the maintenance instructions in the owner’s
manual.
Never drop or insert objects into any opening. Keep hands
away from moving parts.
Do not set anything on the stationary handrails,
handlebars, control console, or covers. Place liquids,
magazines, and books in the appropriate receptacles.
Do not lean on or pull on the console at any time.
CAUTION: DO NOT remove the cover, or you may risk injury due
to electric shock. Read the assembly and maintenance guide
before operating. There are no user-serviceable parts inside.
Contact Customer Support if the equipment needs servicing. For
use with single phase AC power only.
8
Assembling and Maintaining Elliptical Fitness Crosstrainers: EFX 883 / 833
Educating Users
Take time to educate users about the Important Safety
Instructions found in both the User Reference Manual and
Product Owner’s Manual. Explain to your club or facility
patrons that they should observe the following precautions:



Hold onto a stationary handrail or handlebar while
assuming the starting position on the equipment.
Face the console at all times.
Hold on to a stationary handrail or handlebar with one
hand whenever you operate the console keys with the
other hand.
Hazardous Materials and Proper Disposal
The batteries within self-powered equipment contain
materials that are considered hazardous to the environment.
Federal law requires proper disposal of these batteries.
If you plan to dispose of your equipment, contact Precor
Commercial Products Customer Support for information
regarding battery removal. Refer to Obtaining Service.
Product Recycling and Disposal
This equipment must be recycled or discarded according to
applicable local and national regulations.
Product labels, in accordance with European Directive
2002/96/EC concerning waste electrical and electronic
equipment (WEEE), determine the framework for the return
and recycling of used equipment as applicable throughout the
European Union. The WEEE label indicates that the product is
not to be thrown away, but rather reclaimed upon end of life
per this Directive.
In accordance with the European WEEE Directive, electrical
and electronic equipment (EEE) is to be collected separately
and to be reused, recycled, or recovered at end of life. Users
of EEE with the WEEE label per Annex IV of the WEEE
Directive must not dispose of end of life EEE as unsorted
municipal waste, but use the collection framework available
to customers for the return, recycling, and recovery of WEEE.
Customer participation is important to minimize any potential
effects of EEE on the environment and human health due to
the potential presence of hazardous substances in EEE. For
proper collection and treatment, refer to Obtaining Service.
9
Important Safety Instructions
Regulatory Notices for the RFID Module
When equipped with a control console as described in this
document, this equipment may include a radio-frequency
identification (RFID) module. The RFID module has been
certified to operate at temperatures between -20°C and 85°C
(-4°F and 185°F).
Radio Frequency Interference (RFI)
The RFID module conforms to the following national
standards defining acceptable limits for radio frequency
interference (RFI).
Federal Communications Commission, Part 15
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a commercial
installation. The equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in
accordance with the owner’s manual instructions, can cause
harmful interference to radio communications.
Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
WARNING
Per FCC rules, changes or modifications not
expressly approved by the manufacturer could
void the user’s authority to operate the
equipment.
10
Assembling and Maintaining Elliptical Fitness Crosstrainers: EFX 883 / 833
Industry Canada
This device complies with RSS-210:2007 of the Spectrum
Management & Telecommunications Radio Standards
Specification. Operation is subject to the following two
conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference
received, including interference that may cause undesired
operation.
This Class A digital apparatus complies with Canadian
ICES-003.
Cet appareil numérique de la classe A est conforme à la norme
NMB-003 du Canada.
ATTENTION: Haute Tension
Débranchez avant de réparer
European Applications
CE compliance is claimed to the following directives:
1999/5/EC R&TTE Directive
2006/95/EC LVD Directive
2002/95/EC RoHS Directive
Directive compliance has been verified to the following
standards:









EN 55022
EN 300 330-1 V1.5.1
EN 300 330-2 V1.3.1
EN 301 489-3 V1.4.1
EN 301 489-1 V1.8.1
EN 60950-1
11
Important Safety Instructions
Regulatory Notices for Cardiovascular
Exercise Equipment
The regulatory information in this section applies to the
exercise equipment and its control console.
Safety Approvals for Cardiovascular Equipment
Precor equipment has been tested and found to comply with
the following applicable safety standards.
Cardiovascular Type Equipment:
 CAN/CSA, IEC, EN 60335-1 (Household and similar

electrical appliances - Safety)
EN 957 (Stationary training equipment, class S/B
compliant equipment)
PVS and P80 Regulatory Notice
This Precor equipment has been tested and found to comply
with the following applicable safety standards.

CAN/CSA, UL, IEC, EN 60065 (Audio, video and similar
electronic apparatus - Safety)
Radio Frequency Interference (RFI)
This Precor exercise equipment conforms to the following
national standards defining acceptable limits for radio
frequency interference (RFI).
Federal Communications Commission, Part 15
This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a commercial
installation. The equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in
accordance with the owner’s manual instructions, may cause
harmful interference to radio communications.
WARNING
Per FCC rules, changes or modifications not
expressly approved by Precor could void the
user’s authority to operate the equipment.
12
Assembling and Maintaining Elliptical Fitness Crosstrainers: EFX 883 / 833
Industry Canada
This Class A digital apparatus complies with Canadian
ICES-003.
Cet appareil numérique de la classe A est conforme à la norme
NMB-003 du Canada.
ATTENTION: Haute Tension
Débranchez avant de réparer
European Applications
CE compliance is claimed to the following directives:
2004/108/EC EMC Directive
2006/95/EC LVD Directive
2002/95/EC RoHS Directive
Directive compliance has been verified to the following
standards:







EN 55022
EN 55024
EN 60335-1
EN 60065 (P80 and PVS)
Important Safety Instructions
13
Electrical Recommendations: All Equipment
Excluding Treadmills
Note: This is a recommendation only. NEC (National Electric
Code) guidelines or local region electric codes must be
followed.
For equipment fitted with a P80 console or Personal Viewing
System (PVS) screen a separate power connection is
required. For a 20 amp branch circuit up to 10 screens can be
connected. If the branch circuit has any other devices plugged
into the circuit, then the number of screens must be reduced
by the wattage of the other devices.
Note: The typical splitter power cords that have IEC-320 C13
and C14 plugs have a recommended maximum capacity of
five screens.
Figure 1: IEC-320 C13 and C14 plugs
Obtaining Service
Do not attempt to service the equipment except for
maintenance tasks. If any items are missing, contact your
dealer. For more information regarding customer support
numbers or a list of Precor authorized service centers, visit
the Precor web site at http://www.precor.com.
14
Assembling and Maintaining Elliptical Fitness Crosstrainers: EFX 883 / 833
Obtaining Updated Documentation
Current Precor product documentation is available at
http://www.precor.com/productmanuals. You may want to
check in for updated information from time to time.
Table of Contents
Important Safety Instructions .................................................... 3
Safety Precautions ................................................................................ 4
Educating Users .................................................................................... 8
Hazardous Materials and Proper Disposal .................................... 8
Product Recycling and Disposal ....................................................... 8
Regulatory Notices for the RFID Module ....................................... 9
Regulatory Notices for Cardiovascular Exercise Equipment.....11
Electrical Recommendations: All Equipment Excluding
Treadmills ...................................................................................... 13
Obtaining Service................................................................................. 13
Obtaining Updated Documentation ...............................................14
Assembling the EFX ...................................................................17
Installation Requirements.................................................................. 18
Performing the Assembly .................................................................. 21
Leveling the EFX .................................................................................. 33
Breaking in the Equipment ............................................................... 34
Installing the Console ............................................................... 35
Threading the Cable Assembly (P80) .......................................... 36
Connecting Cables (P80) ................................................................. 38
Completing the Console Installation (P80)................................ 44
Threading the Cable Assembly (P30) .......................................... 45
Connecting Cables (P30) ................................................................. 47
Completing the Console Installation (P30) .................................49
Verifying That the Heart Rate Display Is Operational ..............50
Maintenance ...............................................................................51
Daily Cleaning ....................................................................................... 51
Daily Inspection................................................................................... 52
Weekly Maintenance......................................................................... 53
Monthly Maintenance ....................................................................... 53
Storing the Chest Strap ..................................................................... 54
Moving the Equipment ...................................................................... 54
Long-Term Storage ............................................................................ 54
16
Assembling and Maintaining Elliptical Fitness Crosstrainers: EFX 883 / 833
Self-Powered Features.............................................................. 55
Informational Displays Prior to Shutdown .................................. 56
Symptoms of a Low Battery ............................................................ 56
Using the Optional Power Adapter ................................................57
The Optional Power Adapter Kit.....................................................57
Replacing the Battery ........................................................................ 58
Commercial Cardiovascular Equipment Limited Warranty..... 59
Chapter
1
Assembling the EFX
WARNING
You will need the assistance of two other
people to assemble this unit. DO NOT attempt
assembly by yourself.
Important: The instructions in the following procedures are
described from the perspective of a person standing directly in
front of the equipment (that is, on the opposite side of the
control console from a person using the equipment). These
descriptions may not match the names of certain parts in the parts
list, because such parts are named relative to the back of the
equipment.
To prepare the EFX for assembly:
 Open the box and assemble the components in the
sequence presented in this guide.
 Assemble and operate your equipment on a hard, level
surface in the area intended for use.
 Use a hand truck or furniture dolly to move the EFX unit.
Important: Do not grasp the unit by any of its plastic parts to
move it. The plastic parts are non-structural covers and are
not capable of supporting the weight of the unit.
 Provide ample space around the unit.
 Assemble the equipment according to the guidelines in
this manual to ensure that you do not void the Precor
Limited Warranty.
Important: Any damage caused during installation is not
covered by the Precor Limited Warranty.
18
Assembling and Maintaining Elliptical Fitness Crosstrainers: EFX 883 / 833

Begin installation of all fasteners by hand, then partially
tighten them. Do not fully tighten fasteners until
instructed to do so.
Important: When wrench-tightening the screws, make sure
the head of the fastener is parallel to the product surface. If it
is not, stop tightening to avoid cross-threading. To avoid
further damage, stop assembly work and contact Customer
Support.
Installation Requirements
Prior to assembly, make sure you have the required tools and
hardware.
Hardware Kit (not to scale)
The hardware kit shipped with this equipment contains the
fasteners and other hardware components shown in the
following table. Before you begin assembly, make sure that
your hardware kit is complete. If not, please contact Precor
Customer Support.
Fasteners
Quantity
Flat washers (⁵₁₆-inch)
14
Split washers (⁵₁₆-inch)
14
Flat head hex drive
screws (¹₄-inch x
⁵₈-inch)
4
Phillips-head machine
screws (#8 x ³₄-inch)
3
Buttonhead screws
(⁵₁₆–inch x�1
� –inch)
14
19
Assembling the EFX
Fasteners
Center cross bar cap
Outer handrail cap (2)
Inner handrail cap (2)
Quantity
Sockethead cap screws
(#8 x 1¹₂-inch)
4
Self-tapping screws (#8
x 1¹₂-inch)
4
Handlebar bolt wrench
1
20
Assembling and Maintaining Elliptical Fitness Crosstrainers: EFX 883 / 833
Upright support covers (right-hand and left-hand sets)
Required Tools
 #2 Phillips screwdriver
 Rubber mallet
 SAE standard hex wrench set
 SAE standard socket set
 Two ⁹₁₆-inch wrenches (open-end and box-end)
 Wire cutter
21
Assembling the EFX
Performing the Assembly
DANGER Do not attempt to connect electrical power until
all assembly procedures are complete and the
console is properly installed.
As you assemble the EFX, make sure to construct the cable
assembly as directed so that the necessary connections are
accessible when you add the console.
To begin assembly:
1. Remove the lift cover and set it aside.
Important: Grease on the lift screw can stain clothing. Be
careful not to get grease on your clothing as you remove the
lift cover. Do not remove the grease from the lift screw,
because it is required for proper operation.
Figure 2: Lift cover removal
22
Assembling and Maintaining Elliptical Fitness Crosstrainers: EFX 883 / 833
2. Thread the cable through the left upright support. Tape it
to the top of the upright support to secure it temporarily.
Important: Do not stretch, crimp, or damage the cable.
Cables damaged by improper installation will not be covered
by the Precor Limited Warranty.
Figure 3: Route the cable
23
Assembling the EFX
3. Attach the left upright support to the base frame using
four buttonhead screws, four split washers, and four
⁵₁₆-inch washers. Partially tighten the fasteners.
Figure 4: Attach the upright support to the base frame
4. Repeat steps 2 through 4 to attach the right upright
support.
5. Using a right-angle ³₁₆" hex wrench, remove the four ¹₄" x
³₄" buttonhead screws securing the central plastic base
cover.
6. Remove the tape at the top of the left upright support.
7. Feed one of the cables you want to install down through
the upright support, then along the inside of the foot
support and back through the central frame member. The
following illustration shows the general path of the cable.
Figure 5: EFX cable path
24
Assembling and Maintaining Elliptical Fitness Crosstrainers: EFX 883 / 833
8. Pull the end of the cable upward through the opening just
behind the lift motor, as shown in the previous illustration.
9. Locate the tabbed end of the modular plug coupler. Snap
this end of the coupler into the square opening in the jack
panel.
10. Slide the quick-disconnect terminal on the grounding lead
of the power cable over the grounding terminal on the
equipment frame.
11. Attach the cable to the appropriate connector inside the
base of the EFX, as shown in the following illustration and
table.
Important: Install coaxial cable using a torque wrench and
torque to not exceed 8 lb-in. If a torque wrench is not
available, install the coaxial cable using a wrench to “snug +
¼ turn.” It is permissible to use a wrench on the internal nut
to aid the tightening process.
Figure 6: Cable connection points inside EFX base
25
Assembling the EFX
Connect …
To …
The console power cable (red
and black, individual leads)
The power connector on the
jack panel
The television cable (black
and round)
The coaxial connector on the
jack panel
The Ethernet cable (black and The eight-connector modular
flat)
jack on the jack panel
12. Repeat steps 7 through 9 for the remaining cables you
want to install.
13. Replace the central plastic base cover, then attach the
four buttonhead screws you removed along with the
cover. Tighten the screws completely.
14. Replace the lift cover that was removed in the first step.
Figure 7: Lift cover replacement
26
Assembling and Maintaining Elliptical Fitness Crosstrainers: EFX 883 / 833
To mount the center column support on the frame:
Note: Check that the base fasteners are loose before
installing the fasteners for the central column support.
1.
Have your assistant support the center column support
while you align the inside mounting brackets with the
upright supports.
2. Fasten the center column support to each upright support
by threading a buttonhead screw, a ⁵₁₆-inch washer, and a
split washer through opposite mounting holes.
Figure 8: Rear view of console attachment
Important: When wrench-tightening the screws, make sure
the head of the fastener is parallel to the product surface. If it
is not, stop tightening to avoid cross-threading. To avoid
further damage, stop assembly work and contact Customer
Support.
27
Assembling the EFX
3. Check alignments and thread the remaining four center
column support screws, four ⁵₁₆-inch washers, and four
split washers. Tighten with a ³₁₆-inch hex key so the
assemblies come together, but leave room for
adjustments.
Figure 9: Attachment of center column support
To tighten the fasteners properly:
CAUTION: Upright support fasteners must be properly aligned
and wrench-tightened in the order described below. If improperly
assembled, the upright supports can rub against the ramp. Before
you begin, verify that the base and lift covers are properly aligned
and that the gap between them is even. If not, move the upright
supports until the covers are properly aligned.
1.
Fully tighten the two sets of fasteners on the back of the
center column support.
Figure 10: Fastener attachment detail
28
Assembling and Maintaining Elliptical Fitness Crosstrainers: EFX 883 / 833
2. Fully tighten the fasteners on the back of each upright
support.
Figure 11: Tighten the back fasteners on the upright supports
3. Fully tighten the fasteners on the lower sides of each
upright support.
Figure 12: Tighten the front fasteners on the upright supports
4. Fully tighten the fasteners on the upper front of the center
column support.
Figure 13: Tighten the front fasteners on the center column
support
29
Assembling the EFX
To attach the handlebars:
Important: Attach one handlebar at a time.
1.
Use a ³₁₆-inch hex wrench to loosen the two screws in the
handlebar clamp. Refer to the following illustration for the
location of these fasteners.
Figure 14: Clamp screw location, EFX handlebar bracket
2. Connect the heart rate cable from the console to the heart
rate cable from the handlebars and place excess cable
inside the handlebar.
Figure 15: Threading of the heart rate cable
Important: Do not stretch, crimp, or damage the cable.
Cables damaged by improper installation will not be covered
by the Precor Limited Warranty.
3. Insert the right handlebar into the handlebar clamp until
the foam grip touches the side of the handlebar clamp.
30
Assembling and Maintaining Elliptical Fitness Crosstrainers: EFX 883 / 833
4. Apply pressure to the handlebar and rotate it back and
forth to ease it into the handlebar clamp.
5. Slide the inner handlebar cap onto the lower handlebar.
6. Thread one hex head screw through the handlebar and
handlebar mount. Partially tighten the screw.
Figure 16: Handrail attachment detail
7. Repeat steps 1 through 7 to attach the opposite
handlebar.
To tighten the handlebars completely:
1. Use the wrench included with the unit, or a 1³₈-inch
socket, box, or open-end wrench, to tighten the handlebar
screws fully.
2. Use a ³₁₆-inch hex wrench to tighten the two handlebar
clamp fasteners fully.
3. Insert the center crossbar cap for each handlebar and
press firmly into place.
Figure 17: Center crossbar cap attachment
Note: When secure, the center crossbar caps hold the lift
cover in place.
31
Assembling the EFX
4. Attach the outer handlebar caps.
Figure 18: Outer handrail caps attachment
To attach the water bottle holder:
1. Position the water bottle holder as shown and attach it to
the right stationary handlebar.
Figure 19: Water bottle attachment
2. Secure the holder using three Phillips-head screws.
To attach the upright support covers:
1. Place one inner and one outer upright support cover
around one of the upright supports, aligning them so that
the arrows on their inside surfaces point toward the front
of the equipment.
2. Line up the protrusions on the outer cover with the screw
holes on the inner cover.
32
Assembling and Maintaining Elliptical Fitness Crosstrainers: EFX 883 / 833
3. Apply pressure to both covers so that the protrusions fit
firmly into the screw holes.
4. Secure the upright support covers using two self-tapping
screws.
Figure 20: Upright support cover attachment (right-hand
cover shown)
5. Slide the covers down and snap them into the base
mount.
Note: Be sure to align the covers so that the lip of each
cover fits inside the edge of the base mount and the hook
on the base mount fits into the corresponding slot on the
cover. When you have snapped the covers into place, the
surfaces of the covers and the base mount should line up
smoothly.
6. Repeat steps 1 through 5 to attach the other pair of
upright support covers.
33
Assembling the EFX
Leveling the EFX
Make sure the unit is level before allowing anyone to use it.
CAUTION: To eliminate movement, make sure the adjustable feet
are in contact with the floor.
To level the unit:
1. Gently rock the unit. If there is any movement, ask your
assistant to tip the unit to one side while you locate the
adjustable feet.
2. Correct the height of each adjustable foot as follows.
If you want to … Then turn the adjustable feet …
Raise the unit
Counterclockwise
Lower the unit Clockwise
Figure 21: Rubber pad and adjustable foot locations
Important: Place the unit on a flat surface. Rotating the
adjustable feet cannot compensate for extremely uneven surfaces.
When you are finished adjusting the unit, place the unit on the
floor and recheck that it is level.
34
Assembling and Maintaining Elliptical Fitness Crosstrainers: EFX 883 / 833
Breaking in the Equipment
Precor equipment does not require an actual break-in period.
However, moving components such as belts, gears, and
bearings can settle while the equipment is being stored or
shipped. This can cause the equipment to operate with a
small amount of roughness or noise when it starts up for the
first time.
The equipment usually returns to smooth operation after a
day or two of normal use. If it does not, contact your dealer
for assistance. For more information, refer to Obtaining
Service.
Chapter
2
Installing the Console
To make installation easier, all Precor Experience Series
consoles use the same mounting hardware and connector
locations whenever possible. The installation sequence for
any of them is as follows:
Threading the cable assembly
Connecting cables
Completing the installation (tightening the mounting
screws and attaching the back cover)
The following sections describe how to perform these tasks.



36
Assembling and Maintaining Elliptical Fitness Crosstrainers: EFX 883 / 833
Threading the Cable Assembly (P80)
Earlier in the installation, you threaded the necessary cables
through the frame of the base unit and out the passthrough
opening in the console mount. As you line up the back plate
on the console with the console mount, you must make sure
that the cable assembly passes correctly through the
openings in both components.
Important: Before you begin the following procedure, remove the
rear cover from the control console. To remove the cover, use your
fingernails to pry the lower edge loose, then swing the cover up
and out as shown in the following illustration.
Figure 22: Removing the access cover from the P80 console
To thread the cable assembly:
1. Make sure that as much of each cable as possible passes
through the opening in the middle of the console mount
on the base unit.
2. Position the console over the console mount.
37
Installing the Console
3. Rest the console on the console mount so that the notch
on the bottom of the console’s back plate rests on the
rectangular hook at the bottom of the console mount, as
shown in the following figure.
Figure 23: Console positioning on base unit
4. Tilt the console forward until it stops. Use one hand to
steady the console in this position, or ask your assistant
to do so.
38
Assembling and Maintaining Elliptical Fitness Crosstrainers: EFX 883 / 833
Connecting Cables (P80)
After the console has been seated, separate the individual
cables out of the end of the cable assembly and attach them
to the appropriate circuit connectors inside the console. Refer
to the following diagram and table to identify the cables and
connectors.
Figure 24: Cable connections, P80 console
39
Installing the Console
Table 1. P80 internal cable connections
Cable
Connector Type
Ethernet (LAN)
Eight-contact modular,
on round black cable
TV in
F-type coaxial
Power
Two-contact plug,
polarized and latched
Data from base unit
Eight-contact modular,
on flat gray cable
Heart rate sensors
Four-contact strip, keyed
Circuit
Connector
Location
Safety key (treadmills Six-contact strip, keyed
only)
CSAFE
Eight-contact modular,
on flat gray cable
Automatic stop
sensor (treadmills
only)
Vertical four-contact
strip, keyed
To simplify installation and maintenance, route and connect
cables 1 through 5 according to the following instructions.
Note: In the illustrations in this section, some cables are
omitted for the sake of clarity.
Connecting the Television Cable
The console’s television tuner is mounted inside the console’s
back plate. The tuner includes a short cable adapter that
allows the television cable to be connected outside the back
plate.
To connect the television cable:
1. Pull the cable out through the lower right corner of the
back plate.
2. Route the cable counterclockwise around the outside of
the back plate.
Important: In the following step, install the cable using a
torque wrench and torque not to exceed 8 lb-in. If a torque
wrench is not available, install the coaxial cable using a plain
wrench and tighten to "snug + ¹₄ turn." You may also use a
wrench on the internal nut to help tighten the connection.
40
Assembling and Maintaining Elliptical Fitness Crosstrainers: EFX 883 / 833
3. Attach the connector on the cable to the connector on the
tuner cable and tighten the two connectors securely using
two ⁷₁₆-inch open-end wrenches. Position both
connectors above the upper right corner of the back plate.
4. Use a plastic tie to secure the connectors to the top of the
back plate. Pass the tie through the two small holes near
the upper right corner of the back plate, then wrap it
around the connectors and tighten it securely. Cut off and
remove the protruding end of the tie.
The following illustration shows how the cable is positioned
once it is installed.
Figure 25: Connecting the television cable
Installing the Console
41
Connecting the Ethernet and Base Unit Data Cables
Both the Ethernet and base unit data cables pass through the
cutaway opening at the upper right corner of the back plate
and connect to nearby modular jacks in the console. Because
of this, it is important to exercise caution when connecting
the cables. The black Ethernet cable connects to a jack just
underneath the perforated metal bracket at the very top of the
opening in the console. The gray base unit data cable
connects to a lower jack closer to the back plate.
Refer to the following illustration for the correct position of
both cables.
CAUTION: If you connect the base unit data cable to the wrong
jack, the equipment will not function.
Figure 26: Connecting the Ethernet and base unit data cables
42
Assembling and Maintaining Elliptical Fitness Crosstrainers: EFX 883 / 833
Connecting the Heart Rate Sensor Cable
The heart rate sensor cable passes through the cutaway
opening at the upper left corner of the back plate, then down
to the small circuit board at the lower left of the console. The
following illustration shows how the cable should look once it
is installed.
Figure 27: Connecting the heart rate cable
Installing the Console
43
Connecting the Power Cable
Route the power cable through the cutaway opening at the
upper left corner of the back plate. In the nearby opening
within the steel console framework, locate the socket that
matches the power cable plug and connect the power cable
to it.
Note: Be sure that the latch on the plug clicks into place on
the socket.
The following illustration shows how the cable should look
once it is installed.
Figure 28: Connecting the power cable
44
Assembling and Maintaining Elliptical Fitness Crosstrainers: EFX 883 / 833
Completing the Console Installation (P80)
Important: To allow enough room to attach the console’s back
cover, you must loosen the bracket holding the upper ends of the
handlebars in place. If you do not loosen the bracket, the cover
may break. Using a ³₁₆-inch hex key, loosen the two socket head
cap screws in the bracket by two or three turns each.
Figure 29: Location of screws on handlebar bracket
Before you complete the final installation steps, double-check
the connections you have made. Make sure that all cables are
fully and securely connected, and that any unneeded cables
are tied back properly.
To complete the installation:
1. Feed extra cable back into the neck tube.
2. Tilt the control console backward (toward yourself) until
the tab on the top edge of its back plate slides along the
top edge of the console mount and the screw holes align
properly.
3. Insert the four ⁵₈-inch flat head screws through the holes
in the console mount and thread them into the holes in
the back plate on the console. Partially tighten the screws
using a ⁵₃₂-inch hex wrench.
4. Line up the two small tabs at the top of the console’s back
cover with the slots at the top of the opening in the
console case. Insert the tabs into the slots.
5. Insert the remaining tabs on the back cover with the
corresponding slots on the console case.
6. Press gently on the edges of the back cover to snap it into
place.
7. Using a ³₁₆-inch hex key, fully retighten the two socket
head cap screws securing the handlebar bracket.
Installing the Console
45
Threading the Cable Assembly (P30)
Earlier in the installation, you threaded the necessary cables
through the frame of the base unit and out the passthrough
opening in the console mount. As you line up the back plate
on the console with the console mount, you must make sure
that the cable assembly passes correctly through the
openings in both components.
Important: Before you begin the following procedure, remove the
rear cover from the control console. Set the cover and its mounting
hardware aside for later use.
To thread the cable assembly:
1. Make sure that as much of each cable as possible passes
through the opening in the middle of the console mount
on the base unit.
2. Position the console over the console mount.
46
Assembling and Maintaining Elliptical Fitness Crosstrainers: EFX 883 / 833
3. Rest the console on the console mount so that the notch
on the bottom of the console’s back plate rests on the
rectangular hook at the bottom of the console mount, as
shown in the following figure.
Figure 30: Console positioning on base unit
4. Tilt the console forward until it stops. Use one hand to
steady the console in this position, or ask your assistant
to do so.
47
Installing the Console
5. Pull all cables upward and forward until you can drape
them over the top of the console’s back plate.
Figure 31: Cable positioning
Connecting Cables (P30)
Important: Pass all cables through the semicircular opening just
above the console mount, as shown in the following figure. Do not
attempt to route any cables through other openings or through the
steel channel above the mount.
Figure 32: Cable routing from the mount into the console
48
Assembling and Maintaining Elliptical Fitness Crosstrainers: EFX 883 / 833
After the console has been seated, separate the individual
cables out of the end of the cable assembly and attach them
to the appropriate circuit connectors inside the console. Refer
to the following diagram and table to identify the cables and
connectors.
Figure 33: Cable connections, P30 and P10 consoles
49
Installing the Console
Table 2. P30 and P10 internal cable connections
Cable
Connector Type
Safety key (treadmills
only)
Six-contact strip, keyed
Circuit
Connector
Location
Automatic stop sensor Four-contact strip,
(treadmills only)
keyed
Data from base unit
Eight-contact modular,
on flat gray cable
Heart rate sensors
Four-contact strip,
keyed
CSAFE
Eight-contact modular,
on flat gray cable
Completing the Console Installation (P30)
Before you complete the final installation steps, double-check
the connections you have made. Make sure that all cables are
fully and securely connected, and that any unneeded cables
are tied back properly.
To complete the installation:
1. Feed extra cable back into the neck tube.
2. Tilt the control console backward (toward yourself) until
the tab on the top edge of its back plate slides along the
top edge of the console mount and the screw holes align
properly.
3. Insert the four ⁵₈-inch flat head screws through the holes
in the console mount and thread them into the holes in
the back plate on the console. Partially tighten the screws
using a ⁵₃₂-inch hex wrench.
50
Assembling and Maintaining Elliptical Fitness Crosstrainers: EFX 883 / 833
4. Line up the two small tabs at the bottom of the console’s
back cover with the slots at the bottom of the console
case. Insert the tabs into the slots.
5. Insert the two #8–32 x ¹₂-inch Phillips-head screws that
you removed earlier into the holes at the top edge of the
console’s back cover. Tighten the screws fully.
Important: Use caution not to pinch the cables between the
back cover and PVS mounting screw heads.
6. Fully tighten the four mounting screws (partially
tightened in step 3) using a ⁵₃₂-inch hex wrench.
Verifying That the Heart Rate Display Is
Operational
To verify that the heart rate display is operational:
1. Begin exercising on the equipment.
2. Grasp both touch-sensitive handlebars.
Note: The heart rate is read within ten seconds. During
that time, the heart on the display flashes. You must
maintain contact with both metal plates on each
handlebar to ensure an accurate reading.
3. Look at the HEART RATE display. After a few seconds, a
number appears indicating your heart rate.
4. If a number does not appear in the HEART RATE display,
perform the following checks:
 Verify that the cable connection is properly
connected.
 Repeat the test with a different person. Although the
heart rate display is generally highly accurate, it may
not work properly for a few individuals.
Note: If you use wireless heart rate monitoring, repeat
this test using a chest strap or a wireless pulse simulator
instead of grasping the touch-sensitive handlebars.
Chapter
3
Maintenance
To keep the equipment functioning properly, perform the
minor maintenance tasks in this section at the intervals
shown on the maintenance checklist. Failure to maintain the
equipment as described in this section could void the Precor
Limited Warranty.
DANGER
To reduce the risk of electrical shock, always
disconnect the equipment from its power source
before cleaning it or performing any maintenance
tasks. If the equipment is self-powered but also
uses the optional power adapter, disconnect the
adapter.
Daily Cleaning
Precor recommends that you clean the equipment before and
after each exercise session. To remove dust and dirt from the
equipment, wipe all exposed surfaces with a soft cloth that
you have moistened with one of the following cleaners:


A solution of 30 parts of water to 1 part of Simple Green®
(for more information, visit www.simplegreen.com)
ENVIR-O-SAFE oxygen enhanced cleaner or multi-task
cleaner concentrate, diluted according to the
manufacturer’s instructions (for more information, visit
www.daleyinternational.com)
52
Assembling and Maintaining Elliptical Fitness Crosstrainers: EFX 883 / 833
Alternatively, you can clean the equipment with Athletix
fitness equipment cleaning wipes (for more information, visit
www.athletixproducts.com)
CAUTION: Read and follow the manufacturer’s instructions,
particularly dilution instructions, before using any cleaner on
Precor fitness equipment. Do not use concentrated cleaners at full
strength, or acidic cleaners of any kind; such cleaners weaken the
protective finish on the equipment and void the Precor Limited
Warranty. Never pour water or spray liquids onto any part of the
equipment. Allow the equipment to dry completely before using.
Vacuum the floor underneath the equipment frequently to
prevent the accumulation of dust and dirt that can interfere
with its operation. Use a soft nylon scrub brush to clean the
grooves on equipment with foot pedals.
Daily Inspection
At least once every day, examine the equipment for the
following problems:
Slipping belts
Loose fasteners
Unusual noises
Worn or frayed power cords
Any other indication that the equipment may be in need
of service
Important: If you determine that the equipment needs service,
disconnect all power connections (television, Ethernet, and power)
and move the equipment away from the exercise area. Place an
OUT OF SERVICE sign on the equipment and make it clear to all
patrons and other users that they must not use it.





To order parts or to contact a Precor authorized service
provider in your area, refer to Obtaining Service.
53
Maintenance
Weekly Maintenance
Perform the following maintenance tasks every week:
1. Disconnect the external power supply.
2. Clean the ramps and wheels with water or an approved
cleaner.
3. Inspect the power cord to verify that it is not pinched
under the equipment or between any two moving parts.
4. Clean the floor under the equipment using a vacuum
cleaner or a damp mop.
5. When the floor is completely dry, reconnect the power.
6. Test all console functions, including heart rate monitoring
features.
7. Verify that the unit sits squarely on the floor. All of its feet
should be touching the floor and the unit should not rock
or wobble when in use. If not, re-level it as described in
Leveling the EFX.
Monthly Maintenance
DANGER USE EXTREME CAUTION when the rear cover of
any EFX is removed. Serious injury could result if
fingers are pinched between the flywheel spokes,
cranks, movable arms, and the drive weldment.
Securing the movable arm to the crank with a
clamp is recommended. Be aware of other people
within your work area who might cause the arm
to move.
Perform the following maintenance tasks every month:
1.
Clean the frame, cover and arms with water or an
approved cleaner.
2. Wipe the exterior of the console with a damp sponge or
soft cloth, and dry with a clean towel. Keep water away
from electronic components to prevent electrical shock or
damage.
3. Clean the touchscreen using a soft, lint-free cloth
dampened with a 91% isopropyl alcohol solution (either
as sold or diluted with an equal amount of water).
4. Remove the rear cover. Vacuum out any debris, being
careful not to bring the vacuum cleaner nozzle too close
to any circuit board (unless your vacuum cleaner is
protected against static buildup).
54
Assembling and Maintaining Elliptical Fitness Crosstrainers: EFX 883 / 833
5. Check the belt tension of the step-up and drive belts.
6. Clean and lubricate the lift motor screw with an approved
grease such as SuperLube® with Teflon® or Mobil 1®
synthetic grease (adjustable-ramp models only).
7. Check all fasteners for proper tightness and torque.
8. Replace all covers.
9. Verify that the unit sits squarely on the floor. All of its feet
should be touching the floor and the unit should not rock
or wobble when in use. If not, re-level it as described in
Leveling the EFX.
Storing the Chest Strap
If you purchased the optional heart rate chest strap, store it in
a place where it remains free of dust and dirt (for example, in
a closet or drawer). Be sure to protect the chest strap from
extremes in temperature. Do not store it in a place that may
be exposed to temperatures below 32° F (0° C).
To clean the chest strap, use a sponge or soft cloth dampened
in mild soap and water. Dry the surface thoroughly with a
clean towel.
Moving the Equipment
The equipment is very heavy. If you plan to move it to a new
location, obtain the help of an adult assistant and use proper
lifting techniques. If the equipment includes roller wheels on
one end, use the wheels to reduce the load on yourself and
your assistant.
We recommend a four-wheeled dolly to move Elliptical
Fitness Crosstrainers.
Long-Term Storage
If you do not expect anyone to use the equipment for a long
time, perform the following tasks to prepare it for storage:



If it has a power cord, disconnect the cord.
If it has an optional power adapter, connect the adapter to
prevent damage to the internal battery.
Position it so that it will not become damaged and will not
interfere with people or other equipment.
Chapter
4
Self-Powered Features
Important: This chapter of the manual describes Precor fitness
equipment that can operate without being connected to AC
power. This includes units equipped with P30 or P10 consoles.
However, P80 consoles must be connected to AC power through
their power supplies to operate. For this reason, this chapter does
not apply to units equipped with P80 consoles.
On self-powered equipment, the system initializes and
displays the Welcome screen when a user starts exercising. A
minimum rate of motion must be maintained for the banner to
appear, as shown in the following table. When a person meets
the requirements, the power that is generated allows the
equipment to function properly.
Table 3. Minimum requirements for operation
Equipment Rate of Motion
AMT
40 strides per minute (SPM)
EFX
40 strides per minute (SPM)
Climber
30 steps per minute
Bike
20 revolutions per minute (RPM)
Informational displays appear when the battery is low or
when the rate of motion drops below the minimum
requirements. The display explains what to do to retain
power. If the messages are ignored, the equipment begins
shutdown procedures to maintain the charge of the battery.
Refer to Informational Displays Prior to Shutdown.
An optional power adapter can be purchased and provides
sustained power to the equipment. If you plan to change the
club settings on a unit equipped with a P30 or P10 console,
the power adapter is highly recommended. To purchase the
optional power adapter, check with your dealer. Refer to
Obtaining Service.
56
Assembling and Maintaining Elliptical Fitness Crosstrainers: EFX 883 / 833
Informational Displays Prior to Shutdown
The equipment saves its battery charge by moving into a
shutdown mode. If the user does not maintain the minimum
rate of motion, a 30-second shutdown process begins.
In this mode, the console displays a countdown indicator and
ignores all keypresses. If no movement is detected or the rate
of motion remains below the minimum, the indicator changes
as the countdown continues.
Note: The user can resume exercising before the countdown
period elapses and the workout will continue from the point at
which it was paused.
Important: If the equipment is connected to a CSAFE master
device, it follows a slightly different shutdown process. Ten
seconds before the equipment shuts down, it ends the exercise
session and displays a reset message while it disconnects from the
CSAFE master device. It ignores all keypresses during these last
ten seconds.
Symptoms of a Low Battery
If no one has used the equipment for an extended period of
time, the battery may need recharging.
Symptoms of a low battery include the following:
A flickering or erratic display
Loss of user and program information after the user stops
exercising, without any display of a workout summary or a
notification of pending shutdown
 Inability to decrease the incline setting (if any)
Important: To maintain a constant power source, use the optional
power adapter.


Self-Powered Features
57
Using the Optional Power Adapter
After connecting the power adapter to the equipment, plug
the opposite end into the appropriate power source (120 V or
240 V).
CAUTION: When the optional power adapter is in use, make sure
that the power supply cord does not create a safety hazard. Keep
it out of the way of traffic and moving parts. If the power supply
cord or power conversion module is damaged, it must be replaced.
The control console functions differently when the power
adapter is connected. Because the power adapter provides a
constant source of power, a user can pause for brief periods
without initiating shutdown procedures. When the pause time
limit expires and the user has not resumed exercising, the
console returns to the Welcome screen. The default pause
time is 30 seconds for all fitness equipment. Refer to the
manual for your control console for instructions on setting or
changing the pause time limit. To learn how to install the
power adapter, refer to The Optional Power Adapter Kit.
The Optional Power Adapter Kit
If you purchase the optional power adapter, you must also
purchase the internal cable kit. The kit supplies the cable,
bracket, and fasteners that connect the power adapter to the
lower electronics board.
CAUTION: The internal cable kit must be installed by authorized
service personnel. Do not attempt installation on your own as you
could void the Precor Limited Warranty. For more information,
refer to Obtaining Service.
Important: If this equipment includes a P80 console, the optional
power adapter and the internal cable kit must still be installed to
provide continuous power to the base unit and support its internal
battery.
Once the internal cable kit is installed, you can plug the
optional power adapter into the equipment. Plug the opposite
end into the appropriate power source for your equipment
(120 V or 240 V). Review the safety instructions found at the
beginning of this manual before using the power adapter.
58
Assembling and Maintaining Elliptical Fitness Crosstrainers: EFX 883 / 833
Replacing the Battery
The equipment’s battery is built to last for a long time.
However, if you feel that the battery may need replacing,
check with an authorized service technician. Refer to
Obtaining Service.
CAUTION: The battery stored inside the equipment contains
hazardous materials and must be disposed of according to
Hazardous Waste Regulations. Refer to Hazardous Materials and
Proper Disposal.
Chapter
5
Commercial Cardiovascular
Equipment Limited Warranty
PLEASE READ THESE WARRANTY TERMS AND CONDITIONS CAREFULLY BEFORE
USING YOUR PRECOR INCORPORATED PRODUCT. BY USING THE EQUIPMENT, YOU
ARE CONSENTING TO BE BOUND BY THE FOLLOWING WARRANTY TERMS AND
CONDITIONS.
Limited Warranty.
Precor Incorporated warrants all new Precor products to be free from defects in materials
and manufacture for the warranty periods set forth below. The warranty periods
commence on the invoice date of the original purchase. This warranty applies only against
defects discovered within the warranty period and extends only to the original purchaser
of the product. Parts repaired or replaced under the terms of this warranty will be
warranted for the remainder of the original warranty period only. To claim under this
warranty, the buyer must notify Precor or your authorized Precor dealer within 30 days
after the date of discovery of any nonconformity and make the affected product available
for inspection by Precor or its service representative. Precor’s obligations under this
warranty are limited as set forth below.
Warranty Periods and Coverage.
All Commercial Cardiovascular Products (excluding StretchTrainer, Strength
Products, and coverage specific to certain models and options as defined
below):





Frame: 7 years
Treadmill drive motor: 5 years
Items subject to wear: 1 year
All other parts (including mechanical parts and electronic parts): 2 years
Labor: 1 year
880 Line Commercial Cardiovascular Products (superseding the coverage
above where applicable):


Labor on the P80 console: 2 years
High wear items on the P80 console, including headphone jack, USB connector, and
iPod® connector: 90 days
60
Assembling and Maintaining Elliptical Fitness Crosstrainers: EFX 883 / 833
Options / Accessories
Many options or accessories have components that are connected internally or mounted
inside the electronic console. The following guidelines determine the warranty for these
components. If the internal components are installed by the factory or by an authorized
dealer as part of the original sale and delivery, they have a warranty that is identical to the
warranty of the equipment in which they are connected or mounted. If the internal
components are not installed by the factory or by an authorized dealer as part of the
original sale and delivery, they have a 90 days parts and labor limited warranty. All
components that are not internally connected have a 90 days parts only limited warranty.
Satisfactory proof of purchase is required in all cases.
Conditions and Restrictions.
This warranty is valid only in accordance with the conditions set forth below:
1.
The warranty applies to the Precor product only while
a. it remains in the possession of the original purchaser and proof of purchase is
demonstrated.
b. it has not been subjected to accident, misuse, abuse, improper service, or
non-Precor modification.
c. claims are made within the warranty period.
2. This warranty does not cover damage or equipment failure caused by electrical wiring
not in compliance with electrical codes or Precor owner’s manual specifications, or
failure to provide reasonable and necessary maintenance as outlined in the owner’s
manual.
3. Precor is not responsible for Internet connectivity to its products. This restriction
applies to services, such as those provided by an Internet service provider (ISP), and
also to hardware related to Internet connectivity, such as Ethernet cabling, routers,
servers and switches.
4. Precor is not responsible for the quality of television, video, audio, or other media
supplied to its products. This restriction applies to services, such as those provided
by a cable or satellite television provider; to signal strength and clarity; and also to
hardware related to the reception and delivery of television, video, audio, and other
media. Such hardware can include (but is not limited to) audio, video, and
radio-frequency (RF) cabling, connectors, receivers, modulators, combiners,
distribution amplifiers, splitters, and so on.
5. Precor cannot guarantee that the heart rate measurement system on its products will
work for all users. Heart rate measurement accuracy varies based on a number of
factors, including the user’s physiology and age, the method in which the heart rate
measurement system is used, external interference, and other factors that may
influence heart rate acquisition.
6. Except in Canada, Precor does not pay labor outside the United States.
7. Warranties outside the United States and Canada may vary. Please contact your local
Dealer for details.
Commercial Cardiovascular Equipment Limited Warranty
61
This Limited Warranty shall not apply to:
1. Software version upgrades.
2. Software defects that do not materially and negatively affect the normal performance
of the product under normal conditions of use.
3. Consumable goods or cosmetic items of the product, the exterior of which has been
damaged or defaced as a result of abuse, misuse, accident, improper service or
installation, mishandling, or modification in design or construction not authorized by
Precor.
4. Repairs performed on Precor equipment missing a serial number or with a serial tag
that has been altered or defaced.
5. Service calls to correct installation of the equipment or instruct owners on how to use
the equipment.
6. Pickup and delivery involved with repairs.
7. Any labor costs incurred beyond the applicable labor warranty period.
Disclaimer and Release.
The warranties provided herein are the exclusive warranties given by Precor and
supersede any prior, contrary or additional representations, whether oral or written. ANY
IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF MERCHANTABILITY OR
FITNESS FOR A PARTICULAR PURPOSE THAT APPLY TO ANY PARTS DESCRIBED
ABOVE ARE LIMITED IN DURATION TO THE PERIODS OF EXPRESS WARRANTIES
GIVEN ABOVE FOR THOSE SAME PARTS. PRECOR HEREBY DISCLAIMS AND
EXCLUDES THOSE WARRANTIES THEREAFTER. Some States do not allow limitations on
how long an implied warranty lasts, so the above limitation may not apply to you. PRECOR
ALSO HEREBY DISCLAIMS AND EXCLUDES ALL OTHER OBLIGATIONS OR LIABILITIES,
EXPRESS OR IMPLIED, ARISING BY LAW OR OTHERWISE, WITH RESPECT TO ANY
NONCONFORMANCE OR DEFECT IN ANY PRODUCT, INCLUDING BUT NOT LIMITED
TO: (A) ANY OBLIGATION, LIABILITY, RIGHT, CLAIM OR REMEDY IN TORT, WHETHER
OR NOT ARISING FROM THE NEGLIGENCE OF PRECOR OR ITS SUPPLIERS (WHETHER
ACTIVE, PASSIVE OR IMPUTED); AND (B) ANY OBLIGATION, LIABILITY, RIGHT,
CLAIM OR REMEDY FOR LOSS OF OR DAMAGE TO ANY EQUIPMENT. This disclaimer
and release shall apply even if the express warranty set forth above fails of its essential
purpose.
Exclusive Remedies.
For any product described above that fails to conform to its warranty, Precor will provide,
at their option, one of the following: (1) repair; (2) replacement; or (3) refund of the
purchase price. Precor Limited Warranty service may be obtained by contacting the
authorized dealer from whom you purchased the item. Precor compensates Servicers for
warranty trips within their normal service area to repair commercial equipment at the
customer’s location. You may be charged a trip charge outside the service area. THESE
SHALL BE THE SOLE AND EXCLUSIVE REMEDIES OF THE BUYER FOR ANY BREACH OF
WARRANTY.
62
Assembling and Maintaining Elliptical Fitness Crosstrainers: EFX 883 / 833
EXCLUSION OF CONSEQUENTIAL AND INCIDENTAL
DAMAGES.
PRECOR AND/OR ITS SUPPLIERS SHALL HAVE NO OBLIGATION OR LIABILITY,
WHETHER ARISING IN CONTRACT (INCLUDING WARRANTY), TORT (INCLUDING
ACTIVE, PASSIVE, OR IMPUTED NEGLIGENCE AND STRICT LIABILITY), OR
OTHERWISE, FOR DAMAGE TO THE EQUIPMENT, PROPERTY DAMAGE, LOSS OF USE,
REVENUE OR PROFIT, COST OF CAPITAL, COST OF SUBSTITUTE EQUIPMENT,
ADDITIONAL COSTS INCURRED BY BUYER (BY WAY OF CORRECTION OR
OTHERWISE) OR ANY OTHER INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL
DAMAGES, WHETHER RESULTING FROM NONDELIVERY OR FROM THE USE, MISUSE
OR INABILITY TO USE THE PRODUCT. This exclusion applies even if the above warranty
fails of its essential purposes and regardless of whether such damages are sought for
breach of warranty, breach of contract, negligence, or strict liability in tort or under any
other legal theory. Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights, which
vary from state to state.
Complete this portion and keep for your records.
Purchased From:
Example: Dealer or store name.
Phone Number:
Example: Dealer or store telephone number.
Product/model:
Example: AMT 885 or EFX 883.
Serial number:
The serial number is found on the shipping container.
Effective 1 November 2010
P/N 36286-114
Notes
Notes:
63
64
Notes:
Assembling and Maintaining Elliptical Fitness Crosstrainers: EFX 883 / 833
Assembling and Maintaining
Elliptical Fitness Crosstrainers™
EFX® 883 • EFX® 833
Precor Incorporated
20031 142nd Avenue NE
P.O. Box 7202
Woodinville, WA USA 98072-4002
EFX 8x3 PAG/OM 300712-401 rev H, en
Warranty #36286-114
October 2012
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement