The Wings Maker ARF Handyman Twins aircraft Instruction manual
Below you will find brief information for aircraft ARF Handyman Twins. The Handyman Twins is a twin-engine aircraft that is designed for maximum performance. It has a wingspan of 36.4 inches and a wing area of 346 square inches. The aircraft is powered by two KM28251025 outrunner motors and requires a 4-channel radio with four micro servos, two brushless ESCs, and a 3-cell 11.1V 1800mAh Li-Po battery and charger.
Advertisement
Advertisement
I NST RUCT I ON M ANUAL
.
(GM070XM)
Wing Span: 36.4 in / 925 mm
Wing Area: 346 sq in / 22.3 sq dm
Flying Weight: 28.3 oz / 800 g
Fuselage Length: 41.5 in / 1055 mm
Requires: 4-channel radio w/ 4 micro servos, 2 x Outrunner Motor
KM28251025 w/ Propeller Adaptor HW234040R &
HW2340400, 2 x 15A Brushless ESC,8x4E & 8x4P Propeller,
3 cells 11.1V 1800 mAh Li-Po battery & charger.
Warning ! This model is not a toy.
It is designed for maximum performance. Please seek advice if one is not familiar with this kind of electric powered precision model. Operating this model without prior preparation may cause injuries. Remember, safety is the most important thing. Always keep this instruction manual at hand for quick reference.
* Specifications are subject to change without notice.*
THE WINGS MAKER
FACTORY PRE-FABRICATED
ALMOST-READY-TO-FLY (ARF) SERIES
MADE IN CHINA
.
GM070XMPO30681411
INDEX
BEFORE YOU BEGIN
PARTS LIST
ASSEMBLY
P.1
P.2
P.3-
P.11
SAFETY PRECAUTIONS
BEFORE YOU BEGIN
P.12
1
2
3
Read through the manual before you begin, so you will have an overall idea of what to do.
Check all parts. If you find any defective or missing parts contact your local dealer. Please
DRY FIT and check for defects for all parts that will require CA or Epoxy for final assembly.
Any parts you find to be defective after the gluing process may be difficult to remove for warranty replacement. The manufacturer will replace any defective parts, but will not extend to the parts that are good before gluing to defective parts during assembly. Warranty will not cover any parts modified by customer. For pre-assembled kits, please check proper functions of all servos on the ground before flying. Servo gears could be damaged when control surfaces are hit during transportation of models. The manufacturer will replace any servos due to manufacturer`s defect, but will not cover plane crashes due to damaged servos not detected before flying.
Symbols used throughout this instruction manual comprise of the following :-
Apply epoxy glue.
Apply instant glue
(C.A.glue, super glue.)
Apply thread locker Must be purchased separately !
3mm
Assemble left and right sides the same way.
Peel off shaded portion covering film.
Drill holes with the specified diameter (here: 3mm).
Pay close attention here!
GM070XMPO30681411
P.1
Ensure smooth non-binding movement while assembling.
Cut off shaded portion.
Pierce the shaded portion covering film.
Warning!
Do not overlook this symbol !
Parts List
1.DECALS: GM070XM DEC -- 1 set
MAIN WING -- 1 pair
STABILIZER & ELEVATOR -- 1 set
VERTICAL FIN & RUDDER -- 1 set
FUSELAGE -- 1 set
BATTERY COVER -- 1 set
2.
HINGES PL4115050 -- 4 pcs
3.
HINGES PLL4115050-- 3 pcs
4.DECALS FOR RUDDER - 1 set
5.
HORN PL4113103 -- 1 pc.
SERVO MOUNT -- 2 pcs
6.
FUEL TUBE D2xD4x4mm -- 2 pcs
CLEVIS PL4112105 --1 pc.
STRAPER PL4112106 -- 1 pc.
PUSHROD Ø1.4x125mm w/ Threads (For Rudder) -- 1 pc.
7.
HORN PL4113103 -- 1 pc.
SERVO MOUNT -- 2 pcs
8.
FUEL TUBE D2xD4x4mm -- 2 pcs
CLEVIS PL4112105 --1 pc.
STRAPER PL4112106 -- 1 pc.
PUSHROD Ø1.4x50mm w/ Threads (For Elevator) -- 1 pc.
9.TAIL LANDING GEAR --1 set
SCREW PA2x10mm -- 2 pcs
TAIL WHEEL Ø23mm PL3510230 -- 1 pc.
GM070XMPO30681411 P.2
10.MAIN LANDING GEAR Ø2.5mm -- 1 set
COLLAR Ø2.6mm w/ Set Screw -- 2 sets
MAIN WHEEL Ø40mm PL3116040 -- 2 pcs
SCREW PM2x14mm -- 1 pc.
M2 NYLON INSERT LOCK NUT -- 1 pc.
WASHER d2xD5mm -- 2 pcs
PLYWOOD 21x40x2.5mm (For Main Landing Gear) -- 1 pc.
11.NOSE PIECE -- 1 pc.
12.
HORN PL4113103 -- 2 pcs
HINGES PLL4115050-- 8 pcs
SERVO MOUNT -- 4 pcs
13.
FUEL TUBE D2xD4x4mm -- 4 pcs
CLEVIS PL4112105 --2 pcs
STRAPER PL4112106 -- 2 pcs
PUSHROD Ø1.4x76mm w/ Threads (For Aileron) -- 2 pcs
14.PLYWOOD 30x60x4mm (L)(For Motor) -- 1 pc.
PLYWOOD 30x60x4mm (R)(For Motor) -- 1 pc.
SOCKET HEAD SCREW M3x8mm -- 8 pcs
WASHER d3xD7mm -- 8 pcs
8x4E PROPELLER PL6210804 -- 1 set
8x4P PROPELLER PL6210804P -- 1 set
15.WING TUBE Ø6x365mm -- 1 pc.
SCREW PM3x20mm -- 2 pcs
BATTERY TIE 180mm-- 1 pc.
BATTERY MAT 2x50x150mm-- 2 pcs
1
Decals
Cut out decal sheet, peel off backing sheet and apply on fuselage, stabilizer and wings.
Main wings
Decal
Stabilizer
Top View
Rudder
Bottom View
Top View
Bottom View
After applying the thunderbolt decals across the hinge line, cut it to allow free movement of the Stabilizer.
Fuselage
Right View Left View
Left View
Right View
GM070XMPO30681411 P.3
2
Stabilizer & Elevator
Hinge Setting
Section View
Hinge
Completed
Hinge
Bottom View
For pre-assembled version, the hinges are factory glued.
3
Vertical Fin & Rudder
Hinge Setting
Section View
Hinge
Completed
Hinge
Right View For pre-assembled version, the hinges are factory glued.
4
Decals for Rudder
GM070XMPO30681411
After applying the thunderbolt decals across the hinge line, cut it to allow free movement of the Rudder.
P.4
5
Rudder Servo & Horn
Plastic Bracket
Servo wire
Horn
6
Rudder Pushrod
For pre-assembled version, the horn is factory glued and servo installed.
Straper
Servo Mount
Fuel Tube d2xD4x4mm
Horn
Clevis
Fuel Tube d2xD4x4mm
7
Elevator Servo & Horn
Horn
Plastic Bracket Servo wire
GM070XMPO30681411
Bottom View
Bottom View
For pre-assembled version, the horn is factory glued and servo installed.
P.5
8
Elevator Pushrod
Plastic Stand
Straper
Fuel Tube d2xD4x4mm
Horn
Clevis
9
Tail Landing Gear
PA2x10mm Screw
2
Wheel Ø23mm
PA2x10mm
1.2mm
Bottom View
10
Main Landing Gear
PM2x14mm Screw d2xD5mm Washer
2
M2 Nylon Insert Lock Nut
1
Fuselage
Landing Gear
10
0
2.6mm Collar
Wheel Ø40mm
Landing Gear
M3x3mm Set Screw
GM070XMPO30681411
PM2x14mm
Plywood
26x40x2.5mm
d2xD5mm Washer
M2 Nylon Insert Lock Nut
P.6
Bottom View
Bottom View
Bottom View
11
Nose Piece
12
Aileron Servo & Horn
Hinge Setting
Section View
Hinge
Completed
Servo Mount
Hinge
Servo Mount
Bottom View
Horn
GM070XMPO30681411
Bottom View
For pre-assembled version, the hinges and horn are pre-glued, and servo installed.
P.7
13
Aileron Pushrod
Fuel Tube d2xD4x4mm
Straper
Plastic Stand
Pushrod
Ø1.4x76mm
Clevis
Fuel Tube d2xD4x4mm
Horn
Bottom View
14
Motor Installation
M3x8mm Socket Head Screw
8 d3xD7mm Washer
8
1 8x4E Propeller PL6210804
Propeller Adaptor HW234040R
Plywood 30x60x4mm(L)
M5 Nut (Reverse)
8x4P Propeller PL6210804P
M3x8mm d3xD7mm
Propeller Adaptor HW2340400
Plywood 30x60x4mm(R)
The propellers should curve to the front.
2
M3x8mm d3xD7mm
M5 Nut
3
Decal for Motor Plywood
GM070XMPO30681411
Cut unprinted section of decal sheet to tape motor wires in groove.
P.8
Bottom View
15
Main Wing
PM3x20mm Screw
2
PM3x20mm
Wing Tube Ø6x365mm
Insert carbon fiber wing tube into right wing, align the anchor holes and apply the PM Screw.
PM3x20mm
GM070XMPO30681411
Insert the right wing into the Fuselage. Inset the left wing onto the carbon wing tube, press the wings against the fuselage align the anchor holes and apply the PM Screw.
P.9
16
Radio
Plug in with red+ / black- reversed will damage the ESC.
Motor
Brushless ESC
Receiver Battery
EZ Connector Puller
8x4E Propeller PL6210804
8x4P Propeller PL6210804P
Pilot View
8x4E prop. should be on the left wing, rotating clockwise. 8x4P prop. should be on the right wing, rotating counter-clockwise. If you are using the 3-pin EZ connectors, unplug, rotate 180º and plug back will reverse rotating direction of the motor. For other plugs, interchange any two of the three motor wires connection will reverse the rotating direction. Never reverse the battery connection to the ESC, they must be red to red (+) and black to black ( - ) or the ESC will be damaged.
180mm Y-Cord
EZ Power Y-Cord For Twin ESC
KW1210060
Motor Brushless ESC
Connect the three motor wires of the left motor to the left ESC, and right motor to the right ESC.
Connect the throttle control wires of the two ESCs to the Y-chord. The single output plug of the
Y-chord should be connected to the throttle channel of the receiver to control the throttle. Connect the power input plugs of the two ESCs to the EZ Power Y-Chord, the single output plug of the EZ
Power Y-Chord should be connected to the battery before flying. ( The same procedure applies to other types of connectors. )
Battery Tie 180mm Brushless ESC
180mm Y-Cord
Aileron Servo (L)
5
6
3
4
1
2
ID SET
Receiver
Elevator Servo
ESC
Rudder Servo
Plug in the Aileron Servos wire to channel 1
Plug in the Elevator Servo wire to channel 2
Plug in the ESC Throttle wire to channel 3
Plug in the Rudder Servo wire to channel 4
Aileron Servo (R)
Battery Receiver
GM070XMPO30681411
Battery Mat
P.10
17
Battery Cover
18
Control Throws
Elevator
Rudder
Ailerons
50mm
50mm
60mm
60mm
Adjust the control throws as shown in the diagram. These throws are good for general flying. You can adjust according to your personal preference.
40mm
40mm
19
C.G.
The ideal C.G. position is 120mm (4.7 in.) behind the leading edge measured at where the wing meets the fuselage. In order to obtain the C.G. specified, add weight to the fuselage or move the battery position. Check the C.G. before flying.
120mm
4.7 in.
C.G.
GM070XMPO30681411 P.11
http://www.thewingsmaker.com/instructionManuals.php
Warning!
Important Safety Precautions
# First time flyer should never fly by himself / herself. Assistance from experienced flyer
is absolutely necessary.
# Pre-flight adjustment must be done before flying, it is very dangerous to fly a badly
pre-adjusted aircraft.
# is specially designed to be powered by KM28251025 Outrunner Motor.
# Make sure the air field is spacious, never fly the plane too close to people and never get
too close to a running propeller. Extreme caution should be exercised when working with
electric powered models. Make sure the propeller is cleared of all objects, especially your
hands before connecting the battery to the model. Make sure you understand the
operation of the ESC (Electronic Speed Control) by studying the ESC manual. Once you
plug in the battery for electric powered model, always treat the propeller as a rotating one,
as accidental movement of the throttle stick will spin the propeller and could cause injuries.
# Check and re-tighten up all factory assembled screws, use thread locker if necessary.
GM070XMPO30681411 P.12
Pl8210010
180mm Y-Cord
Code No.
Size Package
KW0021800 180mm 1 pc
EZ Power Y-Cord For Twin ESC
Code No.
Size Package
KW1210060 1 pc
EZ Connector Puller
Code No.
Size Package
PL8210030 1 set
GM070XMPO30681411
Outrunner Motor
KM28251025
-Kv (rpm/V): 1025
-Operating Power: 110W
-Operating Voltage: 2-3S Li-Po
-Operating Current: 10A
-Peak Current: 15A (max. 15 sec.)
-Internal Resistance: 50 m ohms
-Diameter: 27.6mm
-Length: 25mm
-Weight: 40g
-Shaft Diameter: 3mm
-Shaft Length: 14 mm
-Mounting Screw:
M3 (Front)
-Distance of Mounting Holes:
16mm and 19mm
8x4E Propeller
Code No.
Size Package
PL6210804 1 pc
8x4P Propeller
Code No.
Size Package
PL6210804P 1 pc
GM070XMPO30681411
www.thewingsmaker.com
GM070XMPO30681411
THE WINGS MAKER

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- twin engine
- maximum performance
- 36.4 inch wingspan
- 346 sq in wing area
- KM28251025 outrunner motors
- 4-channel radio
- 4 micro servos
- 2 brushless ESCs
- 3-cell 11.1V 1800mAh Li-Po battery