Digi RCM2300 User`s manual

RabbitCore RCM2300
C-Programmable Module
User’s Manual
019–0099
• 070831–G
RabbitCore RCM2300 User’s Manual
Part Number 019-0099 • 070831–G • Printed in U.S.A.
© 2001–20076 Rabbit Semiconductor Inc. • All rights reserved.
No part of the contents of this manual may be reproduced or transmitted in any form or by any means
without the express written permission of Rabbit Semiconductor.
Permission is granted to make one or more copies as long as the copyright page contained therein is
included. These copies of the manuals may not be let or sold for any reason without the express written
permission of Rabbit Semiconductor.
Rabbit Semiconductor reserves the right to make changes and
improvements to its products without providing notice.
Trademarks
Rabbit and Dynamic C are registered trademarks of Rabbit Semiconductor Inc.
Rabbit 2000 and RabbitCore are trademarks of Rabbit Semiconductor Inc.
The latest revision of this manual is available on the Rabbit Semiconductor Web site,
www.rabbit.com, for free, unregistered download.
Rabbit Semiconductor Inc.
www.rabbit.com
RabbitCore RCM2300
TABLE OF CONTENTS
Chapter 1. Introduction
1
1.1 RabbitCore RCM2300 Features............................................................................................................1
1.2 Advantages of the RabbitCore RCM2300 ............................................................................................2
1.3 Development and Evaluation Tools......................................................................................................3
1.3.1 Development Software .................................................................................................................3
1.3.2 Development Kit Contents ...........................................................................................................3
1.4 How to Use This Manual ......................................................................................................................4
1.4.1 Additional Reference Information ...............................................................................................4
1.4.2 Using Online Documentation .......................................................................................................4
Chapter 2. Getting Started
7
2.1 Connections ..........................................................................................................................................8
2.1.1 Attach RCM2300 to Prototyping Board ......................................................................................8
2.1.2 Connect Programming Cable .......................................................................................................9
2.1.3 Connect Power Supply ...............................................................................................................10
2.2 Run a Sample Program .......................................................................................................................11
2.2.1 Troubleshooting .........................................................................................................................11
2.3 Where Do I Go From Here? ...............................................................................................................12
2.3.1 Technical Support ......................................................................................................................12
Chapter 3. Running Sample Programs
13
3.1 Sample Programs ................................................................................................................................13
3.1.1 Getting to Know the RCM2300 .................................................................................................14
3.1.2 Serial Communication ................................................................................................................16
3.1.3 Sample Program Descriptions ....................................................................................................18
Chapter 4. Hardware Reference
21
4.1 RCM2300 Digital Inputs and Outputs ................................................................................................21
4.1.1 Dedicated Inputs ........................................................................................................................25
4.1.2 Dedicated Outputs ......................................................................................................................25
4.1.3 Memory I/O Interface ................................................................................................................25
4.1.4 Other Inputs and Outputs ...........................................................................................................25
4.2 Serial Communication ........................................................................................................................26
4.2.1 Serial Ports .................................................................................................................................26
4.2.2 Programming Port ......................................................................................................................26
4.3 Serial Programming Cable..................................................................................................................28
4.3.1 Changing Between Program Mode and Run Mode ...................................................................28
4.3.2 Standalone Operation of the RCM2300 .....................................................................................29
4.4 Other Hardware...................................................................................................................................30
4.4.1 Clock Doubler ............................................................................................................................30
4.4.2 Spectrum Spreader .....................................................................................................................30
User’s Manual
4.5 Memory...............................................................................................................................................31
4.5.1 SRAM ........................................................................................................................................31
4.5.2 Flash EPROM ............................................................................................................................31
4.5.3 Dynamic C BIOS Source Files ..................................................................................................31
Chapter 5. Software Reference
33
5.1 More About Dynamic C .....................................................................................................................33
5.2 I/O .......................................................................................................................................................35
5.2.1 External Interrupts ......................................................................................................................35
5.3 Serial Communication Drivers ...........................................................................................................35
5.4 Upgrading Dynamic C ........................................................................................................................36
5.4.1 Upgrades ....................................................................................................................................36
Appendix A. RabbitCore RCM2300 Specifications
37
A.1 Electrical and Mechanical Characteristics .........................................................................................38
A.1.1 Headers ......................................................................................................................................41
A.1.2 Physical Mounting ....................................................................................................................41
A.2 Bus Loading .......................................................................................................................................42
A.3 Rabbit 2000 DC Characteristics.........................................................................................................44
A.4 I/O Buffer Sourcing and Sinking Limit .............................................................................................45
A.5 Conformal Coating.............................................................................................................................46
A.6 Jumper Configurations.......................................................................................................................47
Appendix B. Prototyping Board
49
B.1 Prototyping Board ..............................................................................................................................50
B.1.1 Prototyping Board Features .......................................................................................................51
B.1.2 Prototyping Board Expansion ...................................................................................................52
B.2 Mechanical Dimensions and Layout..................................................................................................53
B.3 Power Supply .....................................................................................................................................54
B.4 Using the Prototyping Board..............................................................................................................54
B.4.1 Adding Other Components ........................................................................................................57
Appendix C. Power Supply
59
C.1 Power Supplies...................................................................................................................................59
C.2 Battery Backup...................................................................................................................................59
C.2.1 Battery Backup Circuits ............................................................................................................62
C.2.2 Reset Generator .........................................................................................................................62
C.3 Chip Select Circuit .............................................................................................................................63
Appendix D. Sample Circuits
65
D.1
D.2
D.3
D.4
RS-232/RS-485 Serial Communication .............................................................................................66
Keypad and LCD Connections ..........................................................................................................67
External Memory ...............................................................................................................................68
D/A Converter....................................................................................................................................69
Index
71
Schematics
73
User’s Manual
1. INTRODUCTION
The RabbitCore RCM2300 is a very small advanced core module that incorporates the powerful Rabbit® 2000 microprocessor,
flash memory, static RAM, and digital I/O ports, all on a PCB
that is just 1.15" × 1.60" (29.2 mm × 40.6 mm).
The RCM2300 has a Rabbit 2000 microprocessor operating at 22.1 MHz, static RAM,
flash memory, two clocks (main oscillator and timekeeping), and the circuitry necessary
for reset and management of battery backup of the Rabbit 2000’s internal real-time clock
and the static RAM. Two 26-pin headers bring out the Rabbit 2000 I/O bus lines, address
lines, data lines, parallel ports, and serial ports.
The RCM2300 receives its +5 V power from the user board on which it is mounted. The
RabbitCore RCM2300 can interface with all kinds of CMOS-compatible digital devices
through the user board.
1.1 RabbitCore RCM2300 Features
• Small size: 1.15" × 1.60" × 0.55"
(29 mm × 41 mm × 14 mm)
• Microprocessor: Rabbit 2000 running at 22.1 MHz
• 29 parallel I/O lines: 17 configurable for input or output, 8 fixed inputs, 4 fixed outputs
• 11 additional I/O are available via less convenient 0.03" diameter through-hole connection points
• 8 data lines (D0–D7)
• 4 address lines (A0–A3)
• Memory I/0 read, write
• External reset input
• Five 8-bit timers (cascadable in pairs) and one 10-bit timer with two match registers
• 256K flash memory, 128K SRAM
• Real-time clock
• Watchdog supervisor
User’s Manual
1
• Provision for customer-supplied backup battery either onboard or via header connections
• Four CMOS-compatible serial ports. All the serial ports can be configured asynchronously, and two serial ports can be configured synchronously if so desired. The maximum asynchronous baud rate is 691,200 bps (Dynamic C drivers are capable of
handling up to the sustained rate of 345,600 bps), and the maximum synchronous baud
rate is 5.5296 Mbps (user-written drivers can sustain a rate of 2.7648 Mbps). One synchronous port clock line is available only on the programming header.
• The programming port is also routed to the 26-pin headers, which allows the user board
the ability to reprogram the RCM2300.
Appendix A, “RabbitCore RCM2300 Specifications,” provides detailed specifications for
the RCM2300.
1.2 Advantages of the RabbitCore RCM2300
• Fast time to market using a fully engineered, “ready to run” microprocessor core.
• Competitive pricing when compared with the alternative of purchasing and assembling
individual components.
• Easy C-language program development and debugging, including rapid production
loading of programs.
• Generous memory size allows large programs with tens of thousands of lines of code,
and substantial data storage.
• Very small size.
2
RabbitCore RCM2300
1.3 Development and Evaluation Tools
A complete Development Kit, which includes a Prototyping Board and Dynamic C development software, is available for the RCM2300. The Development Kit puts together the
essentials you need to design an embedded microprocessor-based system rapidly and efficiently.
1.3.1 Development Software
The RCM2300 uses the Dynamic C development environment for rapid creation and
debugging of runtime applications. Dynamic C provides a complete development environment with integrated editor, compiler and source-level debugger. It interfaces directly with
the target system, eliminating the need for complex and unreliable in-circuit emulators.
NOTE: The RCM2300 requires Dynamic C v7.04 or later for development. A compatible version is included on the Development Kit CD-ROM.
1.3.2 Development Kit Contents
The RCM2300 Development Kit contains the following items:
• RCM2300 module with 256K flash memory and 128K SRAM.
• RCM2200/RCM2300 Prototyping Board.
• Wall transformer power supply, 12 V DC, 1 A. The power supply is included only with
Development Kits sold for the North American market. Overseas users should use a
locally available power supply capable of delivering 7.5 V to 25 V DC to the Prototyping Board.
• Programming cable with integrated level-matching circuitry.
• Dynamic C CD-ROM, with complete product documentation on CD.
• Getting Started instructions.
• Rabbit 2000 Processor Easy Reference poster.
• Registration card.
User’s Manual
3
1.4 How to Use This Manual
This user’s manual is intended to give users detailed information on the RCM2300 module. It does not contain detailed information on the Dynamic C development environment.
Most users will want more detailed information on some or all of these topics in order to
put the RCM2300 module to effective use.
1.4.1 Additional Reference Information
In addition to the product-specific information contained in the RabbitCore RCM2300
User’s Manual (this manual), two higher level reference manuals are provided in HTML
and PDF form on the accompanying CD-ROM. Advanced users will find these references
valuable in developing systems based on the RCM2300 modules:
• Dynamic C User’s Manual
• Dynamic C Function Reference Manual
• Rabbit 2000 Microprocessor User’s Manual
1.4.2 Using Online Documentation
We provide the bulk of our user and reference documentation in two electronic formats,
HTML and Adobe PDF. We do this for several reasons.
We believe that providing all users with our complete library of product and reference
manuals is a useful convenience. However, printed manuals are expensive to print, stock,
and ship. Rather than include and charge for manuals that every user may not want, or provide only product-specific manuals, we choose to provide our complete documentation
and reference library in electronic form with every Development Kit and with our
Dynamic C development environment.
NOTE: The most current version of Adobe Acrobat Reader can always be downloaded
from Adobe’s Web site at http://www.adobe.com. We recommend that you use version 4.0 or later.
Providing this documentation in electronic form saves an enormous amount of paper by
not printing copies of manuals that users don’t need. It reduces the number of outdated
manuals we have to discard from stock as well, and it makes providing a complete library
of manuals an almost cost-free option. For one-time or infrequent reference, electronic
documents are more convenient than printed ones.
1.4.2.1 Finding Online Documents
The online documentation is installed along with Dynamic C, and an icon for the documentation menu is placed on the workstation’s desktop. Double-click this icon to reach the
menu. If the icon is missing, use your browser to find and load default.htm in the docs
folder, found in the Dynamic C installation folder.
The latest versions of all documents are always available for free, unregistered download
from our Web sites as well.
4
RabbitCore RCM2300
1.4.2.2 Printing Electronic Manuals
We recognize that many users prefer printed manuals for some uses. Users can easily print all or
parts of those manuals provided in electronic form. The following guidelines may be helpful:
• Print from the Adobe PDF versions of the files, not the HTML versions.
• Print only the sections you will need to refer to more than once.
• Print manuals overnight, when appropriate, to keep from tying up shared resources during the work day.
• If your printer supports duplex printing, print pages double-sided to save paper and
increase convenience.
• If you do not have a suitable printer or do not want to print the manual yourself, most
retail copy shops (e.g., Kinkos, AlphaGraphics, CopyMax) will print the manual from
the PDF file and bind it for a reasonable charge—about what we would have to charge
for a printed and bound manual.
User’s Manual
5
6
RabbitCore RCM2300
2. GETTING STARTED
This chapter describes the RCM2300 hardware in more detail,
and explains how to set up and use the accompanying Prototyping Board.
NOTE: This chapter (and this manual) assume that you have the RabbitCore RCM2300
Development Kit. If you purchased an RCM2300 module by itself, you will have to
adapt the information in this chapter and elsewhere to your test and development setup.
Getting Started Manual
7
2.1 Connections
There are three steps to connecting the Prototyping Board for use with Dynamic C and the
sample programs:
1. Attach the RCM2300 to the Prototyping Board.
2. Connect the programming cable between the RCM2300 and the PC.
3. Connect the power supply to the Prototyping Board.
2.1.1 Attach RCM2300 to Prototyping Board
Y3
R29
VCC
VBAT
+
C24
R18
R22
D2
R21
Q4
CAUTION
J2
Battery
Q2
J1
Prototyping
Board
Q3
R26
R19
C12
C15
R15
G
R34
R23
C10
R2
C11 U1
R13
J1
R1
JP2
JP1
Line up the
mounting holes
R17
R37
C8
Q5
R20
C13
R36
C27
R8
C4
Y1
C3
RCM2300
U6
R7
R38
D1
U2
C9
C23
C14
BEN
J3 WD
J2
VCC
D3
RT1
R41
PE6
PD2
PD0
PD1
PD7
PE3
PD6
GND
R39
GND
VCC
Turn the RCM2300 module so that the header pins and the mounting hole of the RCM2300
line up with the sockets and mounting hole on the Prototyping Board as shown in Figure 1.
Align the module header pins from headers J4 and J5 on the bottom side of the RCM2300
into header sockets J1 and J2 on the Prototyping Board.
Figure 1. Install the RCM2300 on the Prototyping Board
8
RabbitCore RCM2300
Although you can install a single module into either the MASTER or the SLAVE position
on the Prototyping Board, all the Prototyping Board features (switches, LEDs, serial port
drivers, etc.) are connected to the MASTER position. We recommend you install a single
module in the MASTER position.
NOTE: It is important that you line up the pins on headers J4 and J5 of the RCM2300
exactly with the corresponding pins of headers J1 and J2 on the Prototyping Board. The
header pins may become bent or damaged if the pin alignment is offset, and the module
will not work. Permanent electrical damage to the module may also result if a misaligned module is powered up.
Press the module’s pins firmly into the Prototyping Board header sockets.
2.1.2 Connect Programming Cable
The programming cable connects the RCM2300 module to the PC workstation running
Dynamic C to permit download of programs and monitoring for debugging.
Connect the 10-pin connector of the
programming cable labeled PROG
to header J1 on the RabbitCore
RCM2300 module as shown in
Figure 2. Be sure to orient the
marked (usually red) edge of the
cable towards pin 1 of the connector.
(Do not use the DIAG connector,
which is used for a normal serial
connection.)
Connect the other end of the programming cable to a COM port on
your PC. Make a note of the port to
which you connect the cable, as
Dynamic C needs to have this
parameter configured when it is
installed.
Figure 2. Connect Programming Cable
to RCM2300
NOTE: COM 1 is the default port used by Dynamic C.
NOTE: Some PCs now come equipped only with a USB port. It may be possible to use
an RS-232/USB converter (Part No. 540-0070) with the programming cable supplied
with the RCM2300 Development Kit. Note that not all RS-232/USB converters work
with Dynamic C.
Getting Started Manual
9
2.1.3 Connect Power Supply
When the above connections have been made, you can connect power to the RabbitCore
Prototyping Board.
Hook the connector from the wall transformer to header J5 on the Prototyping Board as
shown in Figure 3. The connector may be attached either way as long as it is not offset to
one side.
AC Adapter
Prototyping
Board
Reset
Switch
VBAT
+
Y3
R29
VCC
R21
Q4
R19
Q3
R17
R15
Q2
C11 U1
Q5
R20
C13
JP2
JP1
G
R34
R23
C10
R2
R1
C8
R13
PROG
C12
C15
R26
R37
J1
C24
R18
R22
D2
R36
C27
R8
C4
Y1
C3
U6
R7
R38
D1
U2
C9
C23
C14
BEN
J3 WD
J2
VCC
D3
RT1
R41
PE6
PD2
PD7
PE3
PD6
PD0
PD1
GND
R39
GND
VCC
RCM2300
DIAG
Figure 3. Power Supply Connections
Plug in the wall transformer. The power LED (DS1) on the Prototyping Board should light
up. The RCM2300 and the Prototyping Board are now ready to be used.
NOTE: A RESET button is provided on the Prototyping Board to allow hardware reset
without disconnecting power.
To power down the Prototyping Board, unplug the power connector from J5. You should
disconnect power before making any circuit adjustments in the prototyping area, changing
any connections to the board, or removing the RCM2300 from the board.
10
RabbitCore RCM2300
2.2 Run a Sample Program
If you already have Dynamic C installed, you are now ready to test your programming
connections by running a sample program.
If you are using a USB port to connect your computer to the RCM2300 module, choose
Options > Project Options and select “Use USB to Serial Converter” under the
Communications tab.
Find the file PONG.C, which is in the Dynamic C SAMPLES folder. To run the program,
open it with the File menu (if it is not still open), then compile and run it by pressing F9 or
by selecting Run in the Run menu. The STDIO window will open and will display a small
square bouncing around in a box.
2.2.1 Troubleshooting
If Dynamic C appears to compile the BIOS successfully, but you then receive a communication error message when you compile and load the sample program, it is possible that
your PC cannot handle the higher program-loading baud rate. Try changing the maximum
download rate to a slower baud rate as follows.
• Locate the Serial Options dialog in the Dynamic C Options > Project Options >
Communications menu. Select a slower Max download baud rate.
If a program compiles and loads, but then loses target communication before you can
begin debugging, it is possible that your PC cannot handle the default debugging baud
rate. Try lowering the debugging baud rate as follows.
• Locate the Serial Options dialog in the Dynamic C Options > Project Options >
Communications menu. Choose a lower debug baud rate.
If there are any other problems:
• Check to make sure you are using the PROG connector, not the DIAG connector, on the
programming cable.
• Check both ends of the programming cable to ensure that they are firmly plugged into
the PC and the programming port on the RCM2300.
• Ensure that the RCM2300 module is firmly and correctly installed in its connectors on
the Prototyping Board.
• Select a different COM port within Dynamic C. From the Options menu, select
Project Options, then select Communications. Select another COM port from the list,
then click OK. Press <Ctrl-Y> to force Dynamic C to recompile the BIOS. If Dynamic C
still reports it is unable to locate the target system, repeat the above steps until you locate
the active COM port.
Getting Started Manual
11
2.3 Where Do I Go From Here?
If everything appears to be working, we recommend the following sequence of action:
1. Run all of the sample programs described in Chapter 3 to get a basic familiarity with
Dynamic C and the RCM2300’s capabilities.
2. For further development, refer to the RabbitCore RCM2300 User’s Manual for details
of the RCM2300’s hardware and software components.
A documentation icon should have been installed on your workstation’s desktop; click
on it to reach the documentation menu. You can create a new desktop icon that points to
default.htm in the docs folder in the Dynamic C installation folder.
3. For advanced development topics, refer to the Dynamic C User’s Manual, also in the
online documentation set.
2.3.1 Technical Support
NOTE: If you purchased your RCM2300 through a distributor or through a Rabbit Semiconductor partner, contact the distributor or partner first for technical support.
If there are any problems at this point:
• Use the Dynamic C Help menu to get further assistance with Dynamic C.
• Check the Rabbit Semiconductor Technical Bulletin Board at
www.rabbit.com/support/bb/.
• Use the Technical Support e-mail form at www.rabbit.com/support/.
12
RabbitCore RCM2300
3. RUNNING SAMPLE PROGRAMS
To develop and debug programs for the RCM2300 (and for all
other Rabbit Semiconductor hardware), you must install and use
Dynamic C. This chapter provides a tour of the sample programs
for the RCM2300 module.
3.1 Sample Programs
To help familiarize you with the RCM2300 modules, Dynamic C includes several sample
programs. Loading, executing and studying these programs will give you a solid hands-on
overview of the RCM2300’s capabilities, as well as a quick start with Dynamic C as an
application development tool. These programs are intended to serve as tutorials, but then
can also be used as starting points or building blocks for your own applications.
NOTE: It is assumed in this section that you have at least an elementary grasp of ANSI C.
If you do not, see the introductory pages of the Dynamic C User’s Manual for a suggested reading list.
Each sample program has comments that describe the purpose and function of the program.
Before running any of these sample program, make sure that your RCM2300 is connected
to the Prototyping Board and to your PC as described in Section 2.1, “Connections” To
run a sample program, open it with the File menu (if it is not already open), then compile
and run it by pressing F9 or by selecting Run in the Run menu.
Sample programs are provided in the Dynamic C SAMPLES folder. The sample programs
in the Dynamic C SAMPLES/RCM2300 directory demonstrate the basic operation of the
RCM2300.
Complete information on Dynamic C is provided in the Dynamic C User’s Manual.
User’s Manual
13
3.1.1 Getting to Know the RCM2300
The following sample programs can be found in the SAMPLES\RCM2300 folder.
• EXTSRAM.C—demonstrates the setup and simple addressing to an external SRAM.
This program first maps the external SRAM to the I/O Bank 7 register with a maximum
of 15 wait states, chip select strobe (PE7), and allows writes. The first 256 bytes of
SRAM are cleared and read back. Values are then written to the same area and are read
back. The Dynamic C STDIO window will indicate if writes and reads did not occur
Connect an external SRAM as shown below before you run this sample program.
SRAM
RCM2300
Core Module
A0–A3
A0–A3
D0–D7
D0–D7
/WE
/OE
/CE
/IOWR
/IORD
PE7
10 kW
Vcc
• FLASHLED.C—repeatedly flashes LED DS3 on the Prototyping Board on and off.
LED DS3 is controlled by Parallel Port E bit 7 (PE7). LED DS2 will remain on
continuously.
• FLASHLEDS.C—demonstrates the use of coding with assembly instructions, cofunctions, and costatements to flash LEDs DS2 and DS3 on the Prototyping Board on and
off. LEDs DS2 and DS3 are controlled by Parallel Port E bit 1 (PE1) and Parallel Port E
bit 7 (PE7). Once you have compile this program and it is running, LEDs DS2 and DS3
will flash on/off at different rates.
• TOGGLELED.C—demonstrates the use of costatements to detect switch presses using
the press-and-release method of debouncing. As soon as the sample program starts running, LED DS2 on the Prototyping Board (which is controlled by PE1) starts flashing
once per second. Press switch S3 on the Prototyping Board (which is connected to PB3)
to toggle LED DS3 on the Prototyping Board (which is controlled by PE7) on and off.
The pushbutton switch is debounced by the software.
14
RabbitCore RCM2300
• KEYLCD.C—demonstrates a simple setup for a 2 × 6 keypad and a 2 × 20 LCD.
Connect the keypad to Parallel Ports B, C, and D.
PB0—Keypad Col 0
PC1—Keypad Col 1
PB2—Keypad Col 2
PB3—Keypad Col 3
PB4—Keypad Col 4
PB5—Keypad Col 5
PD3—Keypad Row 0
PD4—Keypad Row 1
RCM2200/RCM2300
Prototyping Board
VCC
11
12
13
14
10 kW
resistors
PB0
PB2
PB3
PB4
PB5
4
PC1
10
PD3
PD4
J8
J7
10
Keypad
Col 0
Col 2
Col 3
Col 4
Col 5
Col 1
Row 0
Row 1
NC
NC
11
Connect the LCD to Parallel Port A.
RCM2200/RCM2300
Prototyping Board
6
7
8
680 W
100 nF
5
1 kW
4
3
470 W
3
PA1
PA2
PA3
PA4
PA5
PA6
PA7
2.2 kW
2
4.7 kW
20 kW
J8
2x20 LCD
VLC
10 kW
PA0—backlight (if connected)
PA1—LCD /CS
PA2—LCD RS (High = Control,
Low = Data) / LCD Contrast 0
PA3—LCD /WR/ LCD Contrast 1
PA4—LCD D4 / LCD Contrast 2
PA5—LCD D5 / LCD Contrast 3
PA6—LCD D6 / LCD Contrast 4
PA7—LCD D7 / LCD Contrast 5
2
6
4
5
11
12
13
14
7
8
9
10
VLC
VCC
/CS
RS
/WR
D4
D5
D6
D7
D0
D1
D2
D3
Once the connections have been made and the sample program isrunning, the LCD will
display two rows of 6 dots, each dot representing the corresponding key. When a key is
pressed, the corresponding dot will become an asterisk.
User’s Manual
15
3.1.2 Serial Communication
The following sample programs can be found in the SAMPLES\RCM2300 folder.
One sample programs, PUTS.C, is available to illustrate RS-232 communication. To run
thIs sample program, you will have to add an RS-232 transceiver such as the MAX232 at
location U2 and five 100 nF charge-storage capacitors at C3–C7 on the Prototyping
Board. Also install a 2 × 5 IDC header with a pitch of 0.1" at J6 to interface the RS-232
signals. The diagram shows the connections.
32
2
MAX
ry
ON
100 nF
storage
capacitors
Once the sample program is running, you may use a 10-
Colored
edge
TxC
RxC
GND
J6
TxB
RxB
pin header to DB9 cable (for example, Part No. 540-0009) to
connect header J6 to your PC COM port (you will have to
disconnect the programming cable from both the RCM2300
and the PC if you only have one PC COM port, then press the
RESET button on the Prototyping Board). Line up the
colored edge of the cable with pin 1 on header J6 as shown in
the diagram (pin 1 is indicated by a small square on the
Prototyping Board silkscreen).
This program writes a null terminated string over Serial Port A, B, or C. Only Serial Port
B is accessible by using a 10-pin header to DB9 cable with header J6 on the Prototyping Board.
Use a serial utility such as HyperTerminal or Tera Term to view the string. Use the following configuration for your serial utility.
Bits per second: 19200
Data bits: 8
Parity: None
Stop bits: 1
Flow control: None
To access Serial Port A or Serial Port C, change the 2 to 1 or 3 respectively in the following line in the sample program.
#define SERIAL_PORT2
16
RabbitCore RCM2300
You can then access Serial Port A through HyperTerminal or Tera Term using the programming cable’s DIAG
connector to connect the programming header (J1) on
the RCM2300 to the PC COM port. Serial Port C can be
accessed with your own hookup wire to connect TxC
and RxC as shown from header J6 on the Prototyping
Board to the 10-pin header to DB9 cable, which is connected to the PC COM port.
RxC
TxC
Serial Port C
GND
TxB
RxB
J6
Two sample programs, MASTER.C and SLAVE.C, are available to illustrate RS-485
master/slave communication. To run these sample programs, you will need a second Rabbit-based system with RS-485, and you will also have to add an RS-485 transceiver such
as the SP483E and bias resistors to the Prototyping Board.
The diagram shows the connections.
You will have to connect PC0 and
PC1 (Serial Port D) on the Prototyping Board to the RS-485 transceiver,
and you will connect PD3 to the
RS-485 transceiver to enable or disable the RS-485 transmitter.
PC0
PC1
PD3
47 kW
DI
A
RO
RS-485
CHIP B
DE
Vcc
485+
Vcc
/RE
bias
681 W
termination
220 W
bias
681 W
485–
The RS-485 connections between the slave and master devices are as follows.
•
RS485+ to RS485+
•
RS485– to RS485–
•
GND to GND
• MASTER.C—This program demonstrates a simple RS-485 transmission of lower case
letters to a slave RCM2300. The slave will send back converted upper case letters back
to the master RCM2300 and display them in the STDIO window. Use SLAVE.C to
program the slave RCM2300—reset the slave before you run MASTER.C on the master.
• SLAVE.C—This program demonstrates a simple RS-485 transmission of lower case
letters to a master RCM2300. The slave will send back converted upper case letters
back to the master RCM2300 and display them in the STDIO window. Compile and run
this program on the slave before you use MASTER.C to program the master.
User’s Manual
17
3.1.3 Sample Program Descriptions
3.1.3.1 FLASHLED.C
This program is about as simple as a Dynamic C application can get—the equivalent of
the traditional “Hello, world!” program found in most basic programming tutorials. If you
are familiar with ANSI C, you should have no trouble reading through the source code and
understanding it.
The only new element in this sample application should be Dynamic C’s handling of the
Rabbit microprocessor’s parallel ports. The program:
4. Initializes the pins of Port A as outputs.
5. Sets all of the pins of Port A high, turning off the attached LEDs.
6. Starts an endless loop with a for(;;) expression, and within that loop:
• Writes a bit to turn bit 1 off, lighting LED DS3;
• Waits through a delay loop;
• Writes a bit to turn bit 1 on, turning off the LED;
• Waits through a second delay loop;
These steps repeat as long as the program is allowed to run.
You can change the flash rate of the LED by adjusting the loop values in the two for
expressions. The first loop controls the LED’s “off” time; the second loop controls its “on”
time.
NOTE: Since the variable j is defined as type int, the range for j must be between 0
and 32767. To permit larger values and thus longer delays, change the declaration of j
to unsigned int or long.
More Information
See the section on primitive data types, and the entries for the library functions
WrPortI( ) and BitWrPortI( ) in the Dynamic C User’s Manual.
18
RabbitCore RCM2300
3.1.3.2 FLASHLEDS.C
In addition to Dynamic C’s implementation of C-language programming for embedded
systems, it supports assembly-language programming for very efficient processor-level
control of the module hardware and program flow. This application is similar to
FLASHLED.C and TOGGLELED.C, but uses assembly language for the low-level port control within cofunctions, another powerful multitasking tool.
Dynamic C permits the use of assembly language statements within C code. This program
creates three functions using assembly language statements, then creates a C cofunction to
call two of them. That cofunction is then called within main().
Within each of the C-like functions, the #asm and #endasm directives are used to indicate
the beginning and end of the assembly language statements.
In the function initialize_ports( ), port A is initialized to be all outputs while bit 0
of port E is initialized to be an output.
In the function ledon(), a 0 is written to the port A bit corresponding to the desired LED
(0, which equals DS3, or 1 which equals DS4), turning that LED on. The ledoff( )
function works exactly the same way except that a 1 is written to the bit, turning the
selected LED off.
Finally, in the cofunction flashled(), the LED to be flashed, the on time in milliseconds, and the off time in milliseconds are passed as arguments. This function uses an endless for(;;) loop to call the ledon() and ledoff() functions, separated by calls to
the wait function DelayMs(). This sequence will make the indicated LED flash on and
off.
As is proper in C program design, the contents of main() are almost trivial. The program
first calls initialize_ports(), then begins an endless for(;;) loop. Within this
loop, the program:
1. Calls the library function hitwd(), which resets the microprocessor’s watchdog timer.
(If the watchdog timer is not reset every so often, it will force a hard reset of the system. The purpose is to keep an intermittent program or hardware fault from locking up
the system. Normally, this function is taken care of by the virtual driver, but it is called
explicitly here).
2. Sets up a costatement which calls two instances of the flashled() function, one for
each LED. Note that one LED is flashed one second on, one-half second (500 ms) off,
while the other is flashed in the reverse pattern.
Note also the wfd keyword in the costatement. This keyword (an abbreviation for waitfordone, which can also be used) must be used when calling cofunctions. For a complete
explanation, see Section 5 and 6 in the Dynamic C User’s Manual.
More Information
See the entries for the hitwd() and DelayMs() functions in the Dynamic C User’s
Manual, as well as those for the directives #asm and #endasm. For a complete explanaUser’s Manual
19
tion of how Dynamic C handles multitasking with costatements and cofunctions, see
Chapter 5, “Multitasking with Dynamic C,” and Chapter 6, “The Virtual Driver,” in the
Dynamic C User’s Manual.
3.1.3.3 TOGGLELED.C
One of Dynamic C’s unique and powerful aspects is its ability to efficiently multitask
using cofunctions and costatements. This simple application demonstrates how these program elements work.
This sample program uses two costatements to set up and manage the two tasks. Costatements must be contained in a loop that will “tap” each of them at regular intervals. This
program:
1. Initializes the pins of Port A as outputs.
2. Sets all the pins of Port A high, turning off the attached LEDs.
3. Sets the toggled LED status variable vswitch to 0 (LED off).
4. Starts an endless loop using a while(1) expression, and within that loop:
• Executes a costatement that flashes LED DS3;
• Executes a costatement that checks the state of switch S2 and toggles the state of
vswitch if it is pressed;
• Turns LED DS2 on or off, according to the state of vswitch.
These steps repeat as long as the program is allowed to run.
The first costatement is a compressed version of FLASHLED.c, with slightly different
flash timing. It also uses the library function DelayMs() to deliver more accurate timing
than the simple delay loops of the previous program.
The second costatement does more than check the status of S2. Switch contacts often
“bounce” open and closed several times when the switch is actuated, and each bounce can
be interpreted by fast digital logic as an independent press. To clean up this input, the code
in the second costatement “debounces” the switch signal by waiting 50 milliseconds and
checking the state of the switch again. If it is detected as being closed both times, the program considers it a valid switch press and toggles vswitch.
Unlike most C statements, the two costatements are not executed in their entirety on each
iteration of the while(1) loop. Instead, the list of statements within each costatement is
initiated on the first loop, and then executed one “slice” at a time on each successive interation. This mode of operation is known as a state machine, a powerful concept that permits a single processor to efficiently handle a number of independent tasks.
The ability of Dynamic C to manage state machine programs enables you to create very
powerful and efficient embedded systems with much greater ease than other programming
methods.
More Information
See the entries for the DelayMs() function, as well as Section 5, “Multitasking with
Dynamic C,” in the Dynamic C User’s Manual.
20
RabbitCore RCM2300
4. HARDWARE REFERENCE
Chapter 2 describes the hardware components and principal
hardware subsystems of the RCM2300. Appendix A, “RabbitCore RCM2300 Specifications,” provides complete physical
and electrical specifications.
4.1 RCM2300 Digital Inputs and Outputs
Figure 4 shows the subsystems designed into the RCM2300.
PA0–PA7
Port A
PC0, PC2, PC6
PC1, PC3, PC7
PC6 + 1 more output
PB1, PC7, RES_IN
+ 2 more inputs
STATUS
(WDO)*
SMODE0
SMODE1
Port C
(+Serial Ports A, C & D)
Programming
Port
Port B
(+synch Serial Port B)
Port D
(+Serial Port B)
Port E
RABBIT
2000
(Serial Port A)
Misc. I/O
Real-Time Clock
Watchdog
7 Timers
Slave Port
Clock Doubler
RAM
Backup Battery
Support
/RESET
PD3–PD5
(PD0–PD2,
PD6, PD7)*
PB0,
PB7
PB2–PB5 (PB6)*
Address Lines
I/O Control
Data Lines
PE0–PE2,
PE4–PE5,
PE7
(PE3, PE6)*
A0–A3
(A4)*
IORD
IOWR
(BUFEN)*
D0–D7
Flash
VBAT
* available as a through-hole connection point only,
is not provided on any factory-installed header
Figure 4. Rabbit Subsystems
User’s Manual
21
The RCM2300 modules have two 26-pin headers to which cables can be connected, or
which can be plugged into matching sockets on a production device. The pinouts for these
connectors are shown in Figure 5 below.
J4
GND
PC0
PC2
PC6
PE2
PD4
/IORD
PE0
SMODE1
PE4
STATUS
A3
A1
J5
VCC
PC1
PC3
PC7
PD3
PD5
/IOWR
PE1
SMODE0
PE5
PE7
A2
A0
PA0
PA2
PA4
PA6
/RES
PB2
PB4
PB7
D6
D4
D2
D0
VCC
PA1
PA3
PA5
PA7
PB0
PB3
PB5
D7
D5
D3
D1
VBAT
GND
Note: These pinouts are as seen on
the Bottom Side of the module.
Figure 5. RCM2300 I/O Pinout
Fifteen additional connection points are available along one edge of the RCM2300 board.
These connection points are 0.030" diameter holes spaced 0.05" apart. Nineteen additional
connection points are available at locations J2 and J3. These additional connection points
are reserved for future use.
The remaining discussion is focused on the I/O points available on headers J4 and J5
because it is anticipated that most users will not use the through-hole connection points
because of their reduced convenience.
Table 1 lists the pinout configurations on headers J4 and J5. The ports on the Rabbit 2000
microprocessor used in the RCM2300 are configurable, and so the factory defaults can be
reconfigured. Table 1 lists the factory defaults and the alternate configurations.
.
22
RabbitCore RCM2300
Table 1. RabbitCore RCM2300 Pinout Configurations
Header J4
Pin
Pin Name
Default Use
Alternate Use
1
GND
2
VCC
3
PC0
Output
TXD
4
PC1
Input
RXD
5
PC2
Output
TXC
6
PC3
Input
RXC
7
PC6
Output
TXA
8
PC7
Input
RXA
9
PE2
Bidirectional I/O
I/O control
10
PD3
11
PD4
12
PD5
Bitwise or parallel proATXB output
grammable I/O
ARXB input
13
/IORD
Input (I/O read strobe)
14
/IOWR
Output (I/O write
strobe)
15
PE0
16
PE1
17
SMODE1
Startup mode bit input
Input
18
SMODE0
Startup mode bit input
Input
19
PE4
20
PE5
21
STATUS
Low on first op-code
fetch of instruction
22
PE7
Bitwise or parallel pro- I7 control or slave port
grammable I/O
chip select /SCS
23–26
A[3:0]
User’s Manual
Bitwise or parallel programmable I/O
Bitwise or parallel programmable I/O
Notes
Is also connected to programming port used to
program/debug
I0 control or INT0A input
I1 control or INT1A input
Can only be used as general
inputs after the startup mode
op-code has been read following boot-up
I4 control or INT0B input
I5 control or INT1B input
Output
Accessed by addressing
Global Output Control
Register
Rabbit 2000 address bus
23
Table 1. RabbitCore RCM2300 Pinout Configurations (continued)
Pin
Default Use
Alternate Use
1–8
PA[0:7]
Bytewide
Slave port data bus
programmable parallel
SD0–SD7
I/O
9
/RESET
Reset output
Reset input
PB0
Input
Serial port clock CLKB
input or output
11
PB2
Input
Slave port write /SWR
12
PB3
Input
Slave port read /SRD
13
PB4
Input
SA0
14
PB5
Input
SA1
PB7
Output
Slave port attention line
/SLAVEATTN
10
Header J5
Pin Name
Notes
This weak output can be
driven externally
Slave port address lines
15
16–23 D[7:0]
Input/Output
24
VBAT
3 V battery input
25
VCC
26
GND
24
Rabbit 2000 data bus
RabbitCore RCM2300
4.1.1 Dedicated Inputs
PB0 is a general CMOS input when the Rabbit 2000 is either not using Serial Port B or is
using Serial Port B in an asynchronous mode. Four other general CMOS input-only pins
are located on PB2–PB5. These pins can also be used for the slave port in master/slave
communication between two processors. PB2 and PB3 are slave write and slave read
strobes, while PB4 and PB5 serve as slave address lines SA0 and SA1, and are used to
access the slave registers. PC1, PC3, and PC7 are general CMOS inputs only. These pins
can instead be selectively enabled to serve as the serial data inputs for Serial Ports D, C,
and A.
SMODE0 and SMODE1 are read at start-up, and set the mode whereby instructions are
fetched. Thereafter the user may use and read these pins as inputs by reading the Slave
Port Control Register.
NOTE: Exercise care so that the SMODE0 and SMODE1 pins revert to the correct
startup code when a reset occurs.
4.1.2 Dedicated Outputs
One of the general CMOS output-only pins is located on PB7. PB7 can also be used with
the slave port as the /SLAVEATTN output. This configuration signifies that the slave is
requesting attention from the master. PC0, PC2, and PC6 are also output-only pins; alternatively, they can serve as the serial data outputs for Serial Ports D, C, and A.
The STATUS pin goes low by default after the first op-code fetch of an instruction cycle.
The STATUS pin may be programmed as a separate output by changing the Rabbit 2000’s
Global Output Control Register.
4.1.3 Memory I/O Interface
Four of the Rabbit 2000 address lines (A0–A3) and all the data lines (D0–D7) are available. I/0 write (/IOWR) and I/0 read (/IORD) are also available for interfacing to external
devices.
4.1.4 Other Inputs and Outputs
As shown in Table 1, pins PA0–PA7 can be used to allow the Rabbit 2000 to be a slave to
another processor. The slave port also uses PB2–PB5, PB7, and PE7.
PE0, PE1, PE4, and PE5 can be used for up to two external interrupts. PB0 can be used to
access the clock on Serial Port B of the Rabbit microprocessor. PD4 can be programmed
to be a serial output for Serial Port B. PD5 can be used as a serial input by Serial Port B.
User’s Manual
25
4.2 Serial Communication
The RCM2300 board does not have an RS-232 or an RS-485 transceiver directly on the
board. However, an RS-232 or RS-485 interface may be incorporated on the board the
RCM2300 is mounted on. For example, the Prototyping Board supports a standard
RS-232 transceiver chip.
4.2.1 Serial Ports
There are four serial ports designated as Serial Ports A, B, C, and D. All four serial ports
can sustain their operation in an asynchronous mode up to the baud rate of the system
clock divided by 64. The maximum burst rate for an asynchronous byte can be as high as
the system clock divided by 32. An asynchronous port can handle 7 or 8 data bits. A 9th
bit address scheme, where an additional bit is sent to mark the first byte of a message, is
also supported.
Serial Ports A and B can also be operated in the clocked serial mode. In this mode, a clock
line synchronously clocks the data in or out. Either of the two communicating devices can
supply the clock. When the Rabbit 2000 provides the clock, the sustained baud rate can be
up to the system clock frequency divided by 8, or 2.76 Mbps for a 22.1 MHz clock speed.
The maximum burst rate for a byte can be as high as the system clock divided by 4.
Serial Port A’s clock pin is available only on the programming port, and so is likely to be
inconvenient to interface with.
4.2.2 Programming Port
The RCM2300 has a 10-pin program header labeled J1. The programming port uses the
Rabbit 2000’s Serial Port A for communication. Dynamic C uses the programming port to
download and debug programs.
The programming port is also used for the following operations.
• Cold-boot the Rabbit 2000 after a reset.
• Remotely download and debug a program over an Ethernet connection using the
RabbitLink EG2110.
• Fast copy designated portions of flash memory from one Rabbit-based board (the
master) to another (the slave) using the Rabbit Cloning Board.
Alternate Uses of the Serial Programming Port
All three clocked Serial Port A signals are available as
• a synchronous serial port
• an asynchronous serial port, with the clock line usable as a general CMOS input
The serial programming port may also be used as a serial port via the DIAG connector on
the serial programming cable.
26
RabbitCore RCM2300
In addition to Serial Port A, the Rabbit 2000 startup-mode (SMODE0, SMODE1), status,
and reset pins are available on the serial programming port.
The two startup mode pins determine what happens after a reset—the Rabbit 2000 is
either cold-booted or the program begins executing at address 0x0000. These two
SMODE pins can be used as general inputs once the cold boot is complete.
The status pin is used by Dynamic C to determine whether a Rabbit microprocessor is
present. The status output has three different programmable functions:
1. It can be driven low on the first op code fetch cycle.
2. It can be driven low during an interrupt acknowledge cycle.
3. It can also serve as a general-purpose CMOS output.
The /RESET_IN pin is an external input that is used to reset the Rabbit 2000 and the
onboard peripheral circuits on the RabbitCore module. The serial programming port can be
used to force a hard reset on the RabbitCore module by asserting the /RESET_IN signal.
Refer to the Rabbit 2000 Microprocessor User’s Manual for more information.
User’s Manual
27
4.3 Serial Programming Cable
The programming cable is used to connect the RCM2300’s programming port to a PC
serial COM port. The programming cable converts the RS-232 voltage levels used by the
PC serial port to the TTL voltage levels used by the Rabbit 2000.
When the PROG connector on the programming cable is connected to the RCM2300’s
programming header, programs can be downloaded and debugged over the serial interface.
The DIAG connector of the programming cable may be used on the RCM2300’s programming header with the RCM2300 operating in the Run Mode. This allows the programming
port to be used as a regular serial port.
4.3.1 Changing Between Program Mode and Run Mode
The RCM2300 is automatically in Program Mode when the PROG connector on the
programming cable is attached to the RCM2300, and is automatically in Run Mode when
no programming cable is attached. When the Rabbit 2000 is reset, the operating mode is
determined by the status of the SMODE pins. When the programming cable’s PROG
connector is attached, the SMODE pins are pulled high, placing the Rabbit 2000 in the
Program Mode. When the programming cable’s PROG connector is not attached, the
SMODE pins are pulled low, causing the Rabbit 2000 to operate in the Run Mode.
Program Mode
Run Mode
To PC COM port
RESET RCM2300 when changing mode:
Press RESET button (if using Prototyping Board), OR
Cycle power off/on
after removing or attaching programming cable.
Figure 6. Switching Between Program Mode and Run Mode
A program “runs” in either mode, but can only be downloaded and debugged when the
RCM2300 module is in the Program Mode.
Refer to the Rabbit 2000 Microprocessor User’s Manual for more information on the programming port and the programming cable.
28
RabbitCore RCM2300
4.3.2 Standalone Operation of the RCM2300
The RCM2300 must be programmed via the RCM2200/RCM2300 Prototyping Board or
via a similar arrangement on a customer-supplied board. Once the RCM2300 has been
programmed successfully, remove the programming cable from the programming connector and reset the RCM2300. The RCM2300 may be reset by cycling the power off/on or by
pressing the RESET button on the Prototyping Board. The RCM2300 module may now be
removed from the Prototyping Board for end-use installation.
CAUTION: Power to the Prototyping Board or other boards should be disconnected
when removing or installing your RCM2300 module to protect against inadvertent
shorts across the pins or damage to the RCM2300 if the pins are not plugged in
correctly. Do not reapply power until you have verified that the RCM2300 module is
plugged in correctly.
User’s Manual
29
4.4 Other Hardware
4.4.1 Clock Doubler
The RCM2300 takes advantage of the Rabbit 2000 microprocessor’s internal clock doubler.
A built-in clock doubler allows half-frequency crystals to be used to reduce radiated emissions. The 22.1 MHz frequency is generated using an 11.0592 MHz crystal. The clock doubler is disabled automatically in the BIOS for crystals with a frequency above 12.9 MHz.
The clock doubler may be disabled if 22.1 MHz clock speeds are not required. Disabling
the Rabbit 2000 microprocessor’s internal clock doubler will reduce power consumption
and further reduce radiated emissions. The clock doubler is disabled with a simple configuration macro as shown below.
1. Select the “Defines” tab from the Dynamic C Options > Project Options menu.
2. Add the line CLOCK_DOUBLED=0 to always disable the clock doubler.
The clock doubler is enabled by default, and usually no entry is needed. If you need to
specify that the clock doubler is always enabled, add the line CLOCK_DOUBLED=1 to
always enable the clock doubler. The clock speed will be doubled as long as the crystal
frequency is less than or equal to 26.7264 MHz.
3. Click OK to save the macro. The clock doubler will now remain off whenever you are
in the project file where you defined the macro.
4.4.2 Spectrum Spreader
RCM2300 boards with a Rabbit 2000 microprocessor labeled IQ4T or higher have a spectrum spreader, which helps to mitigate EMI problems. By default, the spectrum spreader is
on automatically for these boards when used with Dynamic C 7.30 or later versions, but
the spectrum spreader may also be turned off or set to a stronger setting. The means for
doing so is through a simple configuration macro as shown below.
1. Select the “Defines” tab from the Dynamic C Options > Project Options menu.
2. Normal spreading is the default, and usually no entry is needed. If you need to specify
normal spreading, add the line
ENABLE_SPREADER=1
For strong spreading, add the line
ENABLE_SPREADER=2
To disable the spectrum spreader, add the line
ENABLE_SPREADER=0
NOTE: The strong spectrum-spreading setting is not necessary for the RCM2300.
3. Click OK to save the macro. The spectrum spreader will now remain off whenever you
are in the project file where you defined the macro.
There is no spectrum spreader functionality for RCM2300 boards with Rabbit 2000 chips
labeled IQ3T or earlier, or with a version of Dynamic C prior to 7.30.
30
RabbitCore RCM2300
4.5 Memory
4.5.1 SRAM
The RCM2300 is designed to accept 128K of SRAM packaged in an SOIC case.
4.5.2 Flash EPROM
The RCM2300 is also designed to accept 128K to 512K of flash EPROM packaged in a
TSOP case.
NOTE: Rabbit Semiconductor recommends that any customer applications should not be
constrained by the sector size of the flash EPROM since it may be necessary to change
the sector size in the future.
Writing to arbitrary flash memory addresses at run time is also discouraged. Instead,
define a “user block” area to store persistent data. The functions writeUserBlock and
readUserBlock are provided for this.
A Flash Memory Bank Select jumper configuration option based on 0 Ω surface-mounted
resistors exists at JP2. This option, used in conjunction with some configuration macros,
allows Dynamic C to compile two different co-resident programs for the upper and lower
halves of the 256K flash in such a way that both programs start at logical address 0000.
This is useful for applications that require a resident download manager and a separate
downloaded program. See Technical Note 218, Implementing a Serial Download Manager for a 256K Flash, for details.
NOTE: Only the Normal Mode, which corresponds to using the full code space, is supported at the present time.
4.5.3 Dynamic C BIOS Source Files
The Dynamic C BIOS source files handle different standard RAM and flash EPROM sizes
automatically.
User’s Manual
31
32
RabbitCore RCM2300
5. SOFTWARE REFERENCE
Dynamic C is an integrated development system for writing
embedded software. It runs on an IBM-compatible PC and is
designed for use with Rabbit Semiconductor single-board computers and other single-board computers based on the Rabbit
microprocessor. Chapter 4 provides the libraries, function calls,
and sample programs related to the RCM2300.
5.1 More About Dynamic C
Dynamic C has been in use worldwide since 1989. It is specially designed for programming embedded systems, and features quick compile and interactive debugging in the real
environment. A complete reference guide to Dynamic C is contained in the Dynamic C
User’s Manual.
You have a choice of doing your software development in the flash memory or in the static
RAM included on the RCM2300. The advantage of working in RAM is to save wear on
the flash memory, which is limited to about 100,000 write cycles.
NOTE: An application can be developed in RAM, but cannot run standalone from RAM
after the programming cable is disconnected. All standalone applications can only run
from flash memory.
NOTE: Do not depend on the flash memory sector size or type. Due to the volatility of
the flash memory market, the RCM2300 and Dynamic C were designed to accommodate flash devices with various sector sizes.
Developing software with Dynamic C is simple. Users can write, compile, and test C and
assembly code without leaving the Dynamic C development environment. Debugging
occurs while the application runs on the target. Alternatively, users can compile a program
to an image file for later loading. Dynamic C runs on PCs under Windows 95, 98, 2000,
NT, Me, and XP. Programs can be downloaded at baud rates of up to 460,800 bps after the
program compiles.
User’s Manual
33
Dynamic C has a number of standard features:
• Full-feature source and/or assembly-level debugger, no in-circuit emulator required.
• Royalty-free TCP/IP stack with source code and most common protocols.
• Hundreds of functions in source-code libraries and sample programs:
X Exceptionally fast support for floating-point arithmetic and transcendental functions.
X RS-232 and RS-485 serial communication.
X Analog and digital I/O drivers.
X I2C, SPI, GPS, file system.
X LCD display and keypad drivers.
• Powerful language extensions for cooperative or preemptive multitasking.
• Loader utility program to load binary images into Rabbit targets in the absence of
Dynamic C.
• Provision for customers to create their own source code libraries and augment on-line
help by creating “function description” block comments using a special format for
library functions.
• Standard debugging features:
X Breakpoints—Set breakpoints that can disable interrupts.
X Single-stepping—Step into or over functions at a source or machine code level, µC/OS-II aware.
X Code disassembly—The disassembly window displays addresses, opcodes, mnemonics, and
machine cycle times. Switch between debugging at machine-code level and source-code level by
simply opening or closing the disassembly window.
X Watch expressions—Watch expressions are compiled when defined, so complex expressions
including function calls may be placed into watch expressions. Watch expressions can be updated
with or without stopping program execution.
X Register window—All processor registers and flags are displayed. The contents of general registers
may be modified in the window by the user.
X Stack window—shows the contents of the top of the stack.
X Hex memory dump—displays the contents of memory at any address.
X STDIO window—printf outputs to this window and keyboard input on the host PC can be
detected for debugging purposes. printf output may also be sent to a serial port or file.
34
RabbitCore RCM2300
5.2 I/O
The RCM2300 was designed to interface with other systems, and so there are no drivers
written specifically for the I/O. The general Dynamic C read and write functions allow
you to customize the parallel I/O to meet your specific needs. For example, use
WrPortI(PEDDR, &PEDDRShadow, 0x00);
to set all the Port E bits as inputs, or use
WrPortI(PEDDR, &PEDDRShadow, 0xFF);
to set all the Port E bits as outputs.
The sample programs in the Dynamic C SAMPLES/RCM2300 directory provide further
examples.
These functions are provided for convenience, not speed. User code should be written in
assembly language when speed is important.
5.2.1 External Interrupts
The Rabbit 2000 microprocessor has four external interrupt inputs on Parallel Port E,
which is accessed through pins PE0, PE1, PE4, and PE5 on header J4. These pins may be
used either as I/O ports or as external interrupt inputs.
Earlier versions of the Rabbit 2000 microprocessor labeled IQ1T or IQ2T would occasionally lose an interrupt request when one of the interrupt inputs was used as a pulse counter.
See Technical Note 301, Rabbit 2000 Microprocessor Interrupt Problem, for further information on how to work around this problem if you purchased your RCM2200 before July,
2002, and the Rabbit 2000 microprocessor is labeled IQ1T or IQ2T.
NOTE: Interrupts on RCM2000 series RabbitCore modules sold after July, 2002, work
correctly and do not need this workaround.
5.3 Serial Communication Drivers
The Prototyping Board has room for an RS-232 chip. Dynamic C has two libraries to support serial communication: RS232.LIB provides a set of circular-buffer-based functions,
and PACKET.LIB provides packet-based support. Packets can be delimited by time gap,
9th bit detection, or special-character detection.
Both the packet-based and the circular-buffer-based routines are available in blocking and
nonblocking (cofunction) flavors. See the Dynamic C User's Manual and Technical Note
213, Rabbit 2000 Serial Port Software, for more details on serial communication.
User’s Manual
35
5.4 Upgrading Dynamic C
Dynamic C patches that focus on bug fixes are available from time to time. Check the Web
site www.rabbit.com/support/ for the latest patches, workarounds, and bug fixes.
The default installation of a patch or bug fix is to install the file in a directory (folder) different from that of the original Dynamic C installation. Rabbit Semiconductor recommends using a different directory so that you can verify the operation of the patch without
overwriting the existing Dynamic C installation. If you have made any changes to the
BIOS or to libraries, or if you have programs in the old directory (folder), make these
same changes to the BIOS or libraries in the new directory containing the patch. Do not
simply copy over an entire file since you may overwrite a bug fix; of course, you may
copy over any programs you have written. Once you are sure the new patch works entirely
to your satisfaction, you may retire the existing installation, but keep it available to handle
legacy applications.
5.4.1 Upgrades
Dynamic C installations are designed for use with the board they are included with, and
are included at no charge as part of our low-cost kits. Dynamic C is a complete software
development system, but does not include all the Dynamic C features. Rabbit Semiconductor also offers add-on Dynamic C modules containing the popular µC/OS-II real-time
operating system, as well as PPP, Advanced Encryption Standard (AES), and other select
libraries. In addition to the Web-based technical support included at no extra charge, a
one-year telephone-based technical support module is also available for purchase.
36
RabbitCore RCM2300
APPENDIX A. RABBITCORE RCM2300
SPECIFICATIONS
Appendix A provides the specifications for the RCM2300, and
describes the conformal coating.
User’s Manual
37
A.1 Electrical and Mechanical Characteristics
Figure A-1 shows the mechanical dimensions for the RCM2300.
1.150
(29.2)
1.060
(26.9)
R38
C3
Y1
R41
PD0
PD1
R8
PD2
U6
R36
C27
PD6
D2
D3
R37
Please refer to the RCM2300
footprint diagram later in this
appendix for precise header
locations.
GND
RT1
D1
R7
C4
R39
J1
PD7
PE3
C9
VCC
R1
PE6
C8
R2
J3 WD
R19
U2
R20
C13
R21
R22
C14
R29
VCC
VBAT
+
Q3
Q4
C24
R18
(20.3)
R26
C23
R17
Y3
Q5
GND
R15
C12
C15
0.800
C11 U1
G
R34
(40.6)
JP2
JP1
J2
R13
Q2
BEN
VCC
R23
1.600
C10
0.125 dia
(6.2)
(2.2)
0.244
0.087
(6.2)
0.244
(2.2)
0.087
(40.6)
(1.6)
1.600
0.063
(14)
0.55
(6.2)
0.244
(29.2)
(1.6)
1.150
0.063
(14)
0.55
(6.2)
0.244
(3.18)
Figure A-1. RabbitCore RCM2300 Dimensions
NOTE: All measurements are in inches followed by millimeters enclosed in parentheses.
All dimensions have a manufacturing tolerance of ±0.01" (0.2 mm).
38
RabbitCore RCM2300
(6.2)
0.24
(3)
0.12
(1)
0.04
It is recommended that you allow for an “exclusion zone” of 0.04" (1 mm) around the
RCM2300 in all directions when the RCM2300 is incorporated into an assembly that
includes other printed circuit boards. An “exclusion zone” of 0.12" (3 mm) is recommended below the RCM2300 when the RCM2300 is plugged into another assembly using
the shortest connectors for headers J4 and J5. Figure A-2 shows this “exclusion zone.”
1.150
0.04
(29.2)
(1)
0.04
Exclusion
Zone
(6.2)
0.24
(3)
0.12
(1)
0.04
(1)
0.04
(1)
J5
1.600
(40.6)
J4
0.04
(1)
Figure A-2. RCM2300 “Exclusion Zone”
User’s Manual
39
Table A-1 lists the electrical, mechanical, and environmental specifications for the RCM2300.
Table A-1. RabbitCore RCM2300 Specifications
Parameter
Specification
Microprocessor
Rabbit 2000® at 22.1 MHz
Flash Memory
256K
SRAM
128K
Backup Battery
General-Purpose I/O*
Additional Inputs
Additional Outputs
Memory I/O Interface
Serial Ports
Serial Rate
Slave Interface
Real-Time Clock
Timers
Watchdog/Supervisor
Power
Operating Temperature
Humidity
Connection for user-supplied backup battery
(to support RTC and SRAM)
29 parallel I/0 lines grouped in five 8-bit ports (shared with serial ports):
• 17 configurable I/O
• 8 fixed inputs
• 4 fixed outputs
2 startup mode, reset
Status, reset
4 address lines, 8 data lines, I/O read/write
(extra address and buffer enable via separate connections)
Four 5 V CMOS-compatible ports.
Two ports are configurable as clocked ports, one is a dedicated RS-232
programming port.
Max. burst rate = CLK/32
Max. sustained rate = CLK/64
A slave port allows the RCM2300 to be used as an intelligent peripheral
device slaved to a master processor, which may either be another Rabbit
2000 or any other type of processor
Yes
Five 8-bit timers cascadable in pairs, one 10-bit timer with 2 match registers
that each have an interrupt
Yes
4.75 V to 5.25 V DC, 108 mA
–40°C to +85°C
5% to 95%, noncondensing
Connectors
Two IDC headers 2 × 13, 2 mm pitch
Board Size
1.15" × 1.60" × 0.55"
(29 mm × 41 mm × 14 mm)
* 15 additional I/O are available via less convenient 0.03" diameter through-hole connection points
40
RabbitCore RCM2300
A.1.1 Headers
The RCM2300 uses headers at J4 and J5 for physical connection to other boards. J4 and J5
are 2 × 13 SMT headers with a 2 mm pin spacing. J1, the programming port, is a 2 × 5
header with a 2 mm pin spacing.
Figure A-3 shows the footprint of another board that the RCM2300 would be plugged
into. These values are relative to the header connectors.
0.079
(2.0)
0.935
J4
0.050
(1.3)
(23.7)
J1
0.645
J2
0.130 dia
0.425
(16.4)
0.715
(18.2)
0.760
(19.3)
(10.8)
(3.3)
J3
0.127
(3.2)
0.605
(15.4)
0.020 sq typ
(0.5)
0.960
(24.4)
RCM2300 Footprint
0.009
J5
(0.2)
0.079
(2.0)
Figure A-3. User Board Footprint for RabbitCore RCM2300
A.1.2 Physical Mounting
An 9/32" or ¼" (7 mm) metal standoff with insulating washers and a 4-40 screw is recommended to attach the RCM2300 to a user board at the hole position shown in Figure A-3.
User’s Manual
41
A.2 Bus Loading
You must pay careful attention to bus loading when designing an interface to the
RCM2300. This section provides bus loading information for external devices.
Table A-2 lists the capacitance for the various Rabbit 2000 I/O ports with SRAM and flash
memory connected.
Table A-2. Capacitance of Rabbit 2000 I/O Ports with External Memory
Input
Capacitance
(pF)
Output
Capacitance
(pF)
Parallel Ports A to E
12
14
Data Lines D0–D7
30
32
Address Lines A0–A12
—
32
I/O Ports
Table A-3 lists the external capacitive bus loading for the various Rabbit 2000 output
ports. Be sure to add the loads for the devices you are using in your system and verify that
they do not exceed the values in Table A-3.
Table A-3. External Capacitive Bus Loading -40°C to +85°C
Clock Speed
(MHz)
Maximum External
Capacitive Loading (pF)
A[4:1]
D[7:1]
22.1
50
A[4:1]
D[7:1]
22.1
100 for 55 ns flash
A0
D0
22.1
100
PD[3:0]
22.1
100
PA[7:0]
PB[7,6]
PC[6,2,0]
PD[7:0]
PE[7:0]
22.1
90
All data, address, and
I/O lines with clock
doubler disabled
11.06
100
Output Port
The values from the table above are derived using 55 ns (flash memory) and 70 ns
(SRAM) memory access times. External capacitive loading can be improved by 10 pF for
commercial temperature ranges, but do not exceed 100 pF. See the AC timing specifications in the Rabbit 2000 Microprocessor Users Manual for more information.
42
RabbitCore RCM2300
Figure A-4 shows a typical timing diagram for the Rabbit 2000 microprocessor external
I/O read and write cycles.
External I/O Read (no extra wait states)
T1
Tw
T2
CLK
A[15:0]
valid
Tadr
/CSx
/IOCSx
TCSx
TCSx
TIOCSx
TIOCSx
/IORD
TIORD
TIORD
/BUFEN
TBUFEN
Tsetup
TBUFEN
D[7:0]
valid
Thold
External I/O Write (no extra wait states)
T1
Tw
T2
CLK
A[15:0]
valid
Tadr
/CSx
/IOCSx
/IOWR
/BUFEN
D[7:0]
TCSx
TCSx
TIOCSx
TIOCSx
TIOWR
TIOWR
TBUFEN
TBUFEN
valid
TDHZV
TDVHZ
Figure A-4. External I/O Read and Write Cycles—No Extra Wait States
Tadr is the time required for the address output to reach 0.8 V. This time depends on the
bus loading. Tsetup is the data setup time relative to the clock. Tsetup is specified from
30%/70% of the VDD voltage level.
User’s Manual
43
Table A-4 lists the parameters shown in these figures and provides minimum or measured
values.
Table A-4. Memory and External I/O Read/Write Parameters
Write Parameters
Read Parameters
Parameter
Description
Value
Tadr
Time from CPU clock rising
edge to address valid
Max.
7 ns @ 20 pF, 5 V (10 ns @ 3.3 V)
14 ns @ 70 pF, 5 V (19 ns @ 3.3 V)
Tsetup
Data read setup time
Min.
2 ns @ 5 V (3 ns @ 3.3 V)
Thold
Data read hold time
Min.
0 ns
Tadr
Time from CPU clock rising
edge to address valid
Max.
7 ns @ 20 pF, 5 V (10 ns @ 3.3 V)
14 ns @ 70 pF, 5 V (19 ns @ 3.3 V)
Thold
Data write hold time from /WEx
Min.
or /IOWR
½ CPU clock cycle
A.3 Rabbit 2000 DC Characteristics
Table A-5 outlines the DC characteristics for the Rabbit 2000 at 5.0 V over the recommended operating temperature range from Ta = –40°C to +85°C, VDD = 4.5 V to 5.5 V.
Table A-5. 5.0 Volt DC Characteristics
Symbol
Parameter
Test Conditions
Min
IIH
Input Leakage High
VIN = VDD, VDD = 5.5 V
IIL
Input Leakage Low
(no pull-up)
VIN = VSS, VDD = 5.5 V -10
IOZ
Output Leakage (no pull-up)
VIN = VDD or VSS,
VDD = 5.5 V
VIL
CMOS Input Low Voltage
VIH
CMOS Input High Voltage
VT
CMOS Switching Threshold VDD = 5.0 V, 25°C
Max
10
-10
CMOS Output Low Voltage
VOH
IOH = See Table A-6
CMOS Output High Voltage (sourcing)
VDD = 4.5 V
µA
0.3 x VDD
V
V
0.2
0.7 x VDD
µA
10
2.4
IOL = See Table A-6
(sinking)
VDD = 4.5 V
Units
µA
0.7 x VDD
VOL
44
Typ
4.2
V
0.4
V
V
RabbitCore RCM2300
A.4 I/O Buffer Sourcing and Sinking Limit
Unless otherwise specified, the Rabbit I/O buffers are capable of sourcing and sinking 8
mA of current per pin at full AC switching speed. Full AC switching assumes a 22.1 MHz
CPU clock and capacitive loading on address and data lines of less than 100 pF per pin.
Address pin A0 and data pin D0 are rated at 16 mA each. Pins A1–A4 and D1–D7 are
each rated at 8 mA. The absolute maximum operating voltage on all I/O is VDD + 0.5 V, or
5.5 V.
Table A-6 shows the AC and DC output drive limits of the parallel I/O buffers when the
Rabbit 2000 is used in the RCM2300.
Table A-6. I/O Buffer Sourcing and Sinking Capability
Output Drive
Pin Name
Sourcing*/Sinking† Limits
(mA)
Output Port Name
Full AC Switching
SRC/SNK
Maximum‡ DC
Output Drive
SRC/SNK
PA [7:0]
8/8
12/12
PB [7, 1, 0]
8/8
12/12
PC [6, 2, 0]
8/8
12/12
PD [7:4]
8/8
12/12
PD [3:0]**
16/16
25/25
PE [7:0]
8/8
12/12
* The maximum DC sourcing current for I/O buffers between VDD
pins is 112 mA.
† The maximum DC sinking current for I/O buffers between VSS
pins is 150 mA.
‡ The maximum DC output drive on I/O buffers must be adjusted
to take into consideration the current demands made my AC
switching outputs, capacitive loading on switching outputs, and
switching voltage.
The current drawn by all switching and nonswitching I/O must
not exceed the limits specified in the first two footnotes.
** The combined sourcing from Port D [7:0] may need to be
adjusted so as not to exceed the 112 mA sourcing limit requirement specified in the first footnote.
User’s Manual
45
A.5 Conformal Coating
The area around the crystal oscillator has had the Dow Corning silicone-based 1-2620
conformal coating applied. The conformally coated area is shown in Figure A-5. The conformal coating protects these high-impedance circuits from the effects of moisture and
contaminants over time.
Conformally coated area
R38
C3
Y1
R41
PD0
PD1
R8
PD2
U6
R36
C27
PD6
D2
D3
R37
C4
GND
RT1
D1
R7
R39
J1
PD7
PE3
C9
VCC
R1
PE6
C8
R2
C10
JP2
JP1
J2
R17
R26
R19
U2
R20
Q3
Q4
Q5
C13
R21
R22
C14
C23
C12
C15
C24
R18
R29
VCC
VBAT
+
Y3
GND
R15
G
R34
J3 WD
C11 U1
R13
Q2
BEN
VCC
R23
Figure A-5. RCM2300 Areas Receiving Conformal Coating
Any components in the conformally coated area may be replaced using standard soldering
procedures for surface-mounted components. A new conformal coating should then be
applied to offer continuing protection against the effects of moisture and contaminants.
NOTE: For more information on conformal coatings, refer to Rabbit Semiconductor
Technical Note 303, Conformal Coatings.
46
RabbitCore RCM2300
A.6 Jumper Configurations
Figure A-6 shows the header locations used to configure the various RCM2300 options
via jumpers.
Top Side
JP1
JP2
Figure A-6. Location of RCM2300 Configurable Positions
Table A-7 lists the configuration options.
Table A-7. RCM2300 Jumper Configurations
Header
JP1
JP2
Description
Pins Connected
1–2
128K/256K
2–3
512K
1–2
Normal Mode
2–3
Bank Mode
Factory
Default
Flash Memory Size
Flash Memory Bank Select
×
×
NOTE: The jumper connections are made using 0 Ω surface-mounted resistors.
User’s Manual
47
48
RabbitCore RCM2300
APPENDIX B. PROTOTYPING BOARD
Appendix B describes the features and accessories of the Prototyping Board, and explains the use of the Prototyping Board to
demonstrate the RCM2300 and to build prototypes of your own
circuits.
User’s Manual
49
B.1 Prototyping Board
The Prototyping Board included in the Development Kit makes it easy to connect an
RCM2300 to a power supply for development. It also provides some basic I/O peripherals
(switches and LEDs), as well as a prototyping area for more advanced hardware development.
The Prototyping Board can be used without modification for the most basic level of evaluation and development.
As you progress to more sophisticated experimentation and hardware development, modifications and additions can be made to the board without modifying or damaging the RabbitCore module itself.
The Prototyping Board is shown in Figure B-1, with its main features identified.
RCM2200/RCM2300
User
Reset
RCM2200/RCM2300
Slave Module
Power
Switch Switches
Master Module
Voltage
Connectors
Input
Connectors
Regulator
Power
User
LED
LEDs
Through-Hole
Prototyping Area
Master Module
Extension Headers
Slave Module
Extension Headers
Battery
CAUTION
RS-232
Signal
Header
Battery
SMT Prototyping
Area
Vcc and GND
Buses
Figure B-1. RCM2200/RCM2300 Prototyping Board
50
RabbitCore RCM2300
B.1.1 Prototyping Board Features
• Power Connection—A 3-pin header is provided at J5 for the power supply connection. Note that both outer pins are connected to ground and the center pin is connected
to the raw V+ input. The cable from the wall transformer provided with the North
American version of the Development Kit ends in a connector that may be connected in
either orientation.
Users providing their own power supply should ensure that it delivers 7.5–25 V DC at
not less than 500 mA. The voltage regulator will get warm in use. (Lower supply voltages will reduce thermal dissipation from the device.)
• Regulated Power Supply—The raw DC voltage provided to the POWER header at J5
is routed to a 5 V linear voltage regulator, which provides stable power to the
RCM2300 and the Prototyping Board. A Shottky diode protects the power supply
against damage from reversed raw power connections.
• Power LED—The power LED lights whenever power is connected to the Prototyping
Board.
• Reset Switch—A momentary-contact, normally open switch is connected directly to the
master RCM2300’s /RES pin. Pressing the switch forces a hardware reset of the system.
• I/O Switches and LEDs—Two momentary-contact, normally open switches are connected to the PB2 and PB3 pins of the master RCM2300, and may be read as inputs by
sample applications.
Two LEDs are connected to the PE1 and PE7 pins of the master RCM2300, and may be
driven as output indicators by sample applications.
The LEDs and switches are connected through JP1, which has traces shorting adjacent
pads together. These traces may be cut to disconnect the LEDs, and an 8-pin header
may then be soldered into JP1 to permit their selective reconnection with jumpers. See
Figure B-4 for details.
• Expansion Areas—The Prototyping Board is provided with several unpopulated areas
for expansion of I/O and interfacing capabilities. See the next section for details.
• Prototyping Area—A generous prototyping area has been provided for the installation
of through-hole components. Vcc (5 V DC) and Ground buses run around the edge of
this area. An area for surface-mount devices is provided to the right of the through-hole
area. Note that there are SMT device pads on both top and bottom of the Prototyping
Board. Each SMT pad is connected to a hole designed to accept a 30 AWG solid wire,
which must be soldered once it is in the hole.
• Master Module Connectors—When the RCM2300 plugged into the MASTER slots,
it can act as the “master” relative to another RabbitCore RCM2200 or RCM2300
plugged into the SLAVE slots, which acts as the “slave.”
This master/slave relationship is not used in the DeviceMate Development Kit where
the “target” RCM2300 is plugged into the MASTER slots, and the RCM2200, which is
used as the DeviceMate hardware platform, is plugged into the SLAVE slots. The Prototyping and Demonstration Board serves only as a means to connect the two RabbitCore modules together to demonstrate the DeviceMate software features in Dynamic C.
User’s Manual
51
• Slave Module Connectors—A second set of connectors is pre-wired to permit installation of a second, slave RCM2200 or RCM2300.
B.1.2 Prototyping Board Expansion
The Prototyping Board comes with several unpopulated areas, which may be filled with
components to suit the user’s development needs. After you have experimented with the
sample programs in the RCM2300 Getting Started Manual, you may wish to expand the
Prototyping Board’s capabilities for further experimentation and development. Refer to
the Prototyping Board schematic (090–0122) for details as necessary.
• Module Extension Headers—The complete pin set of both the master and slave modules is duplicated at these two sets of headers. Developers can solder wires directly into
the appropriate holes, or, for more flexible development, 0.1" pitch 26-pin header strips
can be soldered into place. See Figure B-5 for the header pinouts.
• RS-232—Two 2-wire or one 5-wire RS-232 serial port can be added to the Prototyping
Board by installing an RS-232 driver IC and four capacitors. The Maxim MAX232CPE
driver chip or a similar device is recommended for U2. Refer to the Prototyping Board
schematic for additional details.
A 10-pin 0.1-inch spacing header strip can be installed at J6 to permit connection of a
ribbon cable leading to a standard DE-9 serial connector.
All RS-232 port components mount to the top side of the Prototyping Board below and
to the left of the MASTER module position.
NOTE: The RS-232 chip, capacitors and header strip are available from electronics distributors such as Digi-Key.
• Prototyping Board Component Header—Four I/O pins from the RCM2300 module
are hard-wired to the Prototyping Board LEDs and switches through JP1 on the underside of the Prototyping Board.
52
RabbitCore RCM2300
B.2 Mechanical Dimensions and Layout
4.25
(108)
Battery
CAUTION
Figure B-2 shows the mechanical dimensions and layout for the RCM2300 Prototyping Board.
5.25
(133)
Figure B-2. RCM2300 Prototyping Board Dimensions
Table B-1 lists the electrical, mechanical, and environmental specifications for the Prototyping Board.
Table B-1. RCM2300 Prototyping Board Specifications
Parameter
Specification
Board Size
4.25" × 5.25" × 1.00" (108 mm × 133 mm × 25 mm)
Operating Temperature
–40°C to +70°C
Humidity
5% to 95%, noncondensing
Input Voltage
7.5 V to 25 V DC
Maximum Current Draw
1 A at 12 V and 25°C, 0.7 A at 12 V and 70ºC
(including user-added circuits)
Prototyping Area
2.4" × 4.0" (61 mm × 102 mm) throughhole, 0.1" spacing,
additional space for SMT components
Corner Standoffs/Spacers
4, accept 6-32 × 3/8 screws
User’s Manual
53
B.3 Power Supply
The RCM2300 requires a regulated 5 V ± 0.25 V DC power source to operate. Depending
on the amount of current required by the application, different regulators can be used to
supply this voltage.
The Prototyping Board has an onboard 7805 or equivalent linear regulator that is easy to
use. Its major drawback is its inefficiency, which is directly proportional to the voltage
drop across it. The voltage drop creates heat and wastes power.
A switching power supply may be used in applications where better efficiency is desirable. The LM2575 is an example of an easy-to-use switcher. This part greatly reduces the
heat dissipation of the regulator. The drawback in using a switcher is the increased cost.
The Prototyping Board itself is protected against reverse polarity by a Shottky diode at D2
as shown in Figure B-3.
LINEAR POWER SUPPLY
Vcc
POWER
IN
J5
1
2
3
+RAW
D2
1N5819
DCIN
C1
10 mF
1
7805
U1
3
2
C2
100 nF
Figure B-3. Prototyping Board Power Supply
B.4 Using the Prototyping Board
The Prototyping Board is actually both a demonstration board and a prototyping board. As
a demonstration board, it can be used to demonstrate the functionality of the RCM2300
right out of the box without any modifications to either board. There are no jumpers or dip
switches to configure or misconfigure on the Prototyping Board so that the initial setup is
very straightforward.
The Prototyping Board comes with the basic components necessary to demonstrate the
operation of the RCM2300. Two LEDs (DS2 and DS3) are connected to PE1 and PE7, and
two switches (S2 and S3) are connected to PB2 and PB3 to demonstrate the interface to
the Rabbit 2000 microprocessor. Reset switch S1 is the hardware reset for the RCM2300.
54
RabbitCore RCM2300
To maximize the availability of RCM2300 resources, the demonstration hardware (LEDs
and switches) on the Prototyping Board may be disconnected. This is done by cutting the
traces below the silk-screen outline of header JP1 on the bottom side of the Prototyping
Board. Figure B-4 shows the four places where cuts should be made. An exacto knife
would work nicely to cut the traces. Alternatively, a small standard screwdriver may be
carefully and forcefully used to wipe through the PCB traces.
JP1
Bottom Side
JP1
Cut
PA7
PB0
PB3
PB5
D7
D5
D3
D1
VBAT
PA5
PA4
PA6
/RES
PB2
PB4
D6
PB7
D4
D2
D0
Vcc
Vcc
PC1
PC3
PD1/TPO+
PD3
PD5
/IOWR
J8
GND
PC0
PC2
/PD0TPO–
LNK
PE1
PE3/TPIN+
PE5
J9
PD4
/IORD
PE0
PE4
TPIN–
PE6/ACT
PE7
GND
MASTER
Figure B-4. Where to Cut Traces to Permanently Disable
Demonstration Hardware on Prototyping Board
The power LED (PWR) and the RESET switch remain connected. Jumpers across the
appropriate pins on header JP1 can be used to reconnect specific demonstration hardware
later if needed.
Table B-2. Prototyping Board Jumper Settings
Header JP1
Pins
Description
1–2
PE1 to LED DS2
3–4
PE7 to LED DS3
5–6
PB2 to Switch S2
7–8
PB3 to Switch S3
Note that the pinout at location JP1 on the bottom side of the Prototyping Board (shown in
Figure B-4) is a mirror image of the top-side pinout.
The Prototyping Board provides the user with RCM2300 connection points brought out conveniently to labeled points at headers J7 and J8 on the Prototyping Board. Small to medium
circuits can be prototyped using point-to-point wiring with 20 to 30 AWG wire between the
prototyping area and the holes at locations J7 and J8. The holes are spaced at 0.1" (2.5 mm),
User’s Manual
55
and 40-pin headers or sockets may be installed at J7 and J8. The pinouts for locations J7 and
J8, which correspond to headers J1 and J2, are shown in Figure B-5.
J7/J9
GND
PC0
PC2
TPOUTLNK
PD4
/IORD
PE0
TPINPE4
ACT
A3
A1
J8/J10
VCC
PC1
PC3
TPOUT+
PD3
PD5
/IOWR
PE1
TPIN+
PE5
PE7
A2
A0
PA0
PA2
PA4
PA6
/RES
PB2
PB4
PB7
D6
D4
D2
D0
VCC
PA1
PA3
PA5
PA7
PB0
PB3
PB5
D7
D5
D3
D1
VBAT
GND
Note: These pinouts correspond to the
MASTER/SLAVE positions respectively.
Figure B-5. RCM2300 Prototyping Board Pinout
(Top View)
The small holes are also provided for surface-mounted components that may be installed
to the right of the prototyping area.
Battery
CAUTION
There is a 2.4" × 4" through-hole prototyping space available on the Prototyping Board.
VCC and GND traces run along the edge of the Prototyping Board for easy access. A
GND pad is also provided at the lower right for alligator clips or probes.
VCC trace
GND trace
GND pad
Figure B-6. VCC and GND Traces Along Edge of Prototyping Board
56
RabbitCore RCM2300
B.4.1 Adding Other Components
There is room on the Prototyping Board for a user-supplied RS-232 transceiver chip at
location U2 and a 10-pin header for serial interfacing to external devices at location J6. A
Maxim MAX232 transceiver is recommended. When adding the MAX232 transceiver at
position U2, you must also add 100 nF charge storage capacitors at positions C3–C7 as
shown in Figure B-7.
2
MAX
32
ry
ON
100 nF
storage
capacitors
Figure B-7. Location for User-Supplied RS-232 Transceiver
and Charge Storage Capacitors on Back Side of Prototyping Board
NOTE: The board that is supplied with the DeviceMate Development Kit already has the
RS-232 chip and the storage capacitors installed, and is called the DeviceMate Demonstration Board.
There are two sets of pads at the lower right corner of the Prototyping Board that can be
used for surface-mount prototyping SOIC devices. The silk screen layout separates the
rows into six 16-pin devices (three on each side). However, there are pads between the silk
screen layouts giving the user two 52-pin (2×26) SOIC layouts with 50 mil pin spacing.
There are six sets of pads that can be used for 3- to 6-pin SOT23 packages. There are also
60 sets of pads that can be used for SMT resistors and capacitors in an 0805 SMT package.
Each component has every one of its pin pads connected to a hole in which a 30 AWG
wire can be soldered (standard wire wrap wire can be soldered in for point-to-point wiring
on the Prototyping Board). Because the traces are very thin, carefully determine which set
of holes is connected to which surface-mount pad.
There is also a space above the space for the RS-232 transceiver that can accommodate a
large surface-mounted SOIC component.
User’s Manual
57
58
RabbitCore RCM2300
APPENDIX C. POWER SUPPLY
Appendix C provides information on the current requirements of
the RCM2300, and some background on the chip select circuit
used in power management.
C.1 Power Supplies
The RCM2300 requires a regulated 5 V ± 0.25 V DC power source. The RabbitCore
design presumes that the voltage regulator is on the user board, and that the power is made
available to the RabbitCore board through headers J4 and J5.
An RCM2300 with no loading at the outputs operating at 22.1 MHz typically draws 108 mA.
The RCM2300 will consume an additional 10 mA when the programming cable is used to
connect J1 to a PC.
C.2 Battery Backup
The RCM2300 does not have a factory-installed battery, but there is provision for a customer-supplied battery to back up SRAM and keep the internal Rabbit 2000 real-time
clock running.
Header J5, shown in Figure C-1, allows access to an external battery. This header makes it
possible to connect an external 3 V power supply.
External
Battery
J5
D0
23
24
VBAT
VCC
25
26
GND
Figure C-1. External Battery Connections
at Header J5
User’s Manual
59
The RCM2300 has another battery option available. A customer-installed BR2577A/GA
backup battery can be soldered right on the RCM2300 as shown in Figure C-2. The negative battery connection is to the pin 3 hole in the area corresponding to header area J3.
+
C10
PD2
PD6
D2
BEN
J2
R23
J3 WD
-
C11 U1
R17
R26
R19
U2
R20
Q3
Q4
Q5
C13
R21
R22
C14
C23
C12
C15
C24
R18
R29
VCC
VBAT
+
Y3
GND
R15
G
R34
Q2
VCC
PE6
VCC
R13
+
PD7
PE3
C9
JP2
JP1
+
PD0
PD1
Battery
CAUTION
R37
C8
R2
U6
GND
D3
R1
R7
R8
R36
C27
R41
D1
RT1
C4
R38
R39
Y1
C3
J1
Figure C-2. Installing Onboard Backup Battery on RCM2300
NOTE: Installing an onboard backup battery directly on the RCM2300 will prevent you
from adding a through-hole connector at position J3 pin 3 on the other side of the
RCM2300.
60
RabbitCore RCM2300
Alternatively, you may wish to add a 2-pin connector with a 2 mm pitch for hooking up to
an external backup battery as shown in Figure C-3.
R38
C3
Y1
R41
R7
R1
C8
R2
PD0
PD1
R8
PD2
U6
R36
C27
PD6
D2
D3
R37
C4
GND
RT1
D1
R39
J1
PD7
PE3
C9
+
VCC
PE6
C10
JP2
JP1
J2
R23
Q2
R17
R26
R19
U2
R20
C13
R21
R22
C14
C23
-
C12
C15
C24
R18
Q3
Q4
Q5
R29
VCC
VBAT
+
Y3
GND
R15
G
R34
J3 WD
C11 U1
R13
+
BEN
VCC
Figure C-3. Installing Optional Battery Connector on RCM2300
A lithium battery with a nominal voltage of 3 V and a minimum capacity of 165 mA·h is
recommended. A lithium battery is strongly recommended because of its nearly constant
nominal voltage over most of its life.
The drain on the battery by the RCM2300 is typically 16 µA when no other power is supplied. If a 950 mA·h battery is used, the battery can last more than 6 years:
950 mA·h
------------------------ = 6.8 years.
16 µA
The actual life in your application will depend on the current drawn by components not on
the RCM2300 and the storage capacity of the battery. Note that the shelf life of a lithium
battery is ultimately 10 years.
User’s Manual
61
C.2.1 Battery Backup Circuits
The battery-backup circuit serves three purposes:
• It reduces the battery voltage to the SRAM and to the real-time clock, thereby limiting
the current consumed by the real-time clock and lengthening the battery life.
• It ensures that current can flow only out of the battery to prevent charging the battery.
• A voltage, VOSC, is supplied to U6, which keeps the 32.768 kHz oscillator working
when the voltage begins to drop.
VRAM and Vcc are nearly equal (<100 mV, typically 10 mV) when power is supplied to
the RCM2300.
Figure C-4 shows the RCM2300 battery-backup circuit.
VBAT-EXT
D3
R39
2 kW
VRAM
External Battery
R41
11 kW
Vcc
D2
D1
VBAT
R38
10 kW
R37
22 kW
C17
10 nF
R36
47 kW
C27
10 nF
U6
pin 5
Figure C-4. RCM2300 Battery-Backup Circuit
C.2.2 Reset Generator
The RCM2300 uses a reset generator, U1, to reset the Rabbit 2000 microprocessor when the
voltage drops below the voltage necessary for reliable operation. The reset occurs between
4.50 V and 4.75 V, typically 4.63 V. The RCM2300 has a reset output, pin 9 on header J5.
This reset output can be sensed externally. The output can also be overridden and forced into
any state by using a circuit capable of providing 5 mA of output current.
62
RabbitCore RCM2300
C.3 Chip Select Circuit
The RCM2300 has provision for battery backup, which kicks in to keep VRAM from
dropping below 2 V.
When the RCM2300 is not powered, the battery keeps the SRAM memory contents and
the real-time clock (RTC) going. The SRAM has a powerdown mode that greatly reduces
power consumption. This powerdown mode is activated by raising the chip select (CS)
signal line. Normally the SRAM requires Vcc to operate. However, only 2 V is required
for data retention in powerdown mode. Thus, when power is removed from the circuit, the
battery voltage needs to be provided to both the SRAM power pin and to the CS signal
line. The CS control switch accomplishes this task for the CS signal line.
Figure C-5 shows a schematic of the chip select control switch.
VRAM
R28
/CSRAM
100 kW
Q4
/CS1
Q3
RESET_OUT
/RESET_OUT
Figure C-5. Chip Select Control Switch
In a powered-up condition, the CS control switch must allow the processor’s chip select
signal /CS1 to control the SRAM’s CS signal /CSRAM. So, with power applied, /CSRAM
must be the same signal as /CS1, and with power removed, /CSRAM must be held high
(but only needs to be as high as the battery voltage). Q3 and Q4 are MOSFET transistors
with opposing polarity. They are both turned on when power is applied to the circuit. They
allow the CS signal to pass from the processor to the SRAM so that the processor can periodically access the SRAM. When power is removed from the circuit, the transistors will
turn off and isolate /CSRAM from the processor. The isolated /CSRAM line has a 100 kΩ
pullup resistor to VRAM (R28). This pullup resistor keeps /CSRAM at the VRAM voltage
level (which under no power condition is the backup battery’s regulated voltage at a little
more than 2 V).
Transistors Q3 and Q4 are of opposite polarity so that a rail-to-rail voltage can be passed.
When the /CS1 voltage is low, Q3 will conduct. When the /CS1 voltage is high, Q4 will
conduct. It takes time for the transistors to turn on, creating a propagation delay. This
delay is typically very small, about 10 ns to 15 ns.
User’s Manual
63
64
RabbitCore RCM2300
APPENDIX D. SAMPLE CIRCUITS
This appendix details several basic sample circuits that can be
used with the RCM2300.
• RS-232/RS-485 Serial Communication
• Keypad and LCD Connections
• External Memory
• D/A Converter
User’s Manual
65
D.1 RS-232/RS-485 Serial Communication
RS-232
1
RCM2300
Prototyping Board
V+
V–
C1+
100 nF
J7
3
C1–
4
C2+
5
C2–
VCC
100 nF
2
6
100 nF
100 nF
3
PC0
11
T1IN
4
PC1
12
R1OUT
5
PC2
10
T2IN
6
PC3
9
3
PC0
4
D
4
PC1
1
R
R2OUT
T1OUT
14
TXD
R1IN
13
RXD
T2OUT
7
TXC
R2IN
8
RXC
RCM2300
Prototyping Board
J7
10
PD3
47 kW
3
2
RS-485
VCC
680 W
A
6
B
7
DE
485+
220 W
485–
680 W
RE
SP483EN
Figure D-1. Sample RS-232 and RS-485 Circuits
Sample Program: PUTS.C in SAMPLES/RCM2300.
66
RabbitCore RCM2300
D.2 Keypad and LCD Connections
RCM2300
Prototyping Board
J8
VCC
10 kW
resistors
PB0
PB2
PB3
PB4
PB5
10
11
12
13
14
J7
Keypad
Row 0
Row 2
Row 3
Row 4
Row 5
Row 1
PC1
PD3
PD4
4
10
11
Col 0
Col 1
NC
NC
Figure D-2. Sample Keypad Connections
Sample Program: KEYLCD.C in SAMPLES/RCM2300.
RCM2300
Prototyping Board
2
3
4
5
6
7
8
PA1
PA2
PA3
PA4
PA5
PA6
PA7
100 nF
680 W
3
470 W
1 kW
2.2 kW
4.7 kW
10 kW
20 kW
J8
2x20 LCD
VLC
2
6
4
5
11
12
13
14
7
8
9
10
VLC
VCC
/CS
C/D
/WR
D4
D5
D6
D7
D0
D1
D2
D3
Figure D-3. Sample LCD Connections
Sample Program: KEYLCD.C in SAMPLES/RCM2300. (When Parallel Port A is not being
used for quick communication, its resting, quiescent value is used to set the LCD contrast
level.)
User’s Manual
67
D.3 External Memory
The sample circuit can be used to access 16 bytes on an external 64K memory device.
Larger SRAMs can be written to using this scheme by using other available Rabbit 2000
ports (parallel ports A to E) as address lines to create up to four thousand 16-byte pages.
SRAM
RCM2300
Prototyping Board
A0–A3
A0–A3
D0–D7
D0–D7
/WE
/OE
/CE
/IOWR
/IORD
PE7
10 kW
Vcc
Figure D-4. Sample External Memory Connections
Sample Program: EXTSRAM.C in SAMPLES/RCM2300.
68
RabbitCore RCM2300
D.4 D/A Converter
The output will initially be 0 V to -10.05 V after the first inverting op-amp, and 0 V to
+10.05 V after the second inverting op-amp. All lows produce 0 V out, FF produces 10 V
out. The output can be scaled by changing the feedback resistors on the op-amps. For
example, changing 5.11 kΩ to 2.5 kΩ will produce an output from 0 V to -5 V. Op-amps
with a very low input offset voltage are recommended.
HC374
649 kW
324 kW
162 kW
CT0–CT7
PA0–PA7
20 kW
PE4
E
10 kW
–
10 kW
+
1.19 kW
–
+
V+ > 12 V
V– < –12 V
Vo
4.99 kW
5.11 kW
47 kW
CLK
5.11 kW
10 kW
+5 V
47 kW
22 pF
80.6 kW
40.2 kW
+5 V
22 pF
PE2
Figure D-5. Sample D/A Converter Connections
User’s Manual
69
70
RabbitCore RCM2300
INDEX
A
additional information
online documentation .......... 4
reference information .......... 4
B
backup battery
installing onboard battery . 60
via header J5 ..................... 59
via optional header ............ 61
battery life ............................. 61
battery-backup circuit
external battery connections ........................ 59, 61
reset generator ................... 62
bus loading ............................ 42
C
Dynamic C ........................ 3, 33
add-on modules ................. 36
sample programs ............... 13
standard features ............... 34
debugging ...................... 34
telephone-based technical
support .......................... 36
upgrades and patches ........ 36
USB port settings .............. 11
E
EMI
spectrum spreader feature . 30
exclusion zone ...................... 39
external interrupts ................. 35
F
clock doubler ........................ 30
conformal coating ................. 46
features ................................ 1, 2
Prototyping Board ....... 50, 51
flash memory addresses
user blocks ........................ 31
D
H
Development Kit ..................... 3
DeviceMate ................. 51, 57
digital I/O
I/O buffer sourcing and sinking limits ....................... 45
memory interface .............. 25
SMODE0 .................... 25, 27
SMODE1 .................... 25, 27
digital inputs ......................... 25
digital outputs ....................... 25
dimensions
Prototyping Board ............. 53
RCM2300 .......................... 38
hardware connections
install RCM2300 on Prototyping Board ........................ 8
power supply ..................... 10
programming cable ............. 9
hardware reset ....................... 10
I
I/O buffer sourcing and sinking
limits ............................. 45
J
jumper configurations ........... 47
JP1 (flash memory size) .... 47
JP2 (flash memory bank
select) ...................... 31, 47
jumper locations ................ 47
User’s Manual
M
manuals ....................................4
P
physical mounting ..................41
pin configurations ............23, 25
pinout
Prototyping Board ..............56
RCM2300
J4 ....................................22
J5 ....................................22
power supplies .......................59
chip select circuit ...............63
power supply
connections ........................10
Program Mode .......................28
switching modes ................28
programming cable
PROG connector ................28
RCM2300 connections ........9
programming port ..................26
Prototyping Board ..................50
adding RS-232 transceiver .57
attach modules ...................57
dimensions .........................53
expansion area ...................52
features .........................50, 51
header JP1 location ............55
mounting RCM2300 ............8
optional connections to Rabbit
2000 parallel ports .........55
pinout .................................56
power supply ......................54
prototyping area .................56
specifications .....................53
Vcc and GND traces ..........56
73
R
Rabbit subsystems ................. 21
RCM2300
mounting on Prototyping
Board ............................... 8
reset ....................................... 10
Run Mode .............................. 28
switching modes ................ 28
S
sample circuits ....................... 65
D/A converter .................... 69
external memory ................ 68
keypad and LCD connections ............................... 67
RS-232/RS-485 serial communication ..................... 66
sample programs ................... 13
getting to know the RCM2300
EXTSRAM.C ................ 14
FLASHLED.C ......... 14, 18
FLASHLEDS.C ....... 14, 19
KEYLCD.C ................... 15
TOGGLELED.C ...... 14, 20
PONG.C ............................ 11
serial communication
MASTER.C ................... 17
PUTS.C .......................... 16
SLAVE.C ...................... 17
serial communication ............ 26
serial ports ............................. 26
programming port .............. 26
software
I/O drivers ......................... 35
libraries
PACKET.LIB ................ 35
RS232.LIB ..................... 35
serial communication drivers .................................. 35
74
specifications ......................... 37
bus loading ........................ 42
digital I/O buffer sourcing and
sinking limits ................. 45
dimensions
RCM2300 ...................... 38
electrical, mechanical, and
environmental ............... 40
exclusion zone ................... 39
header footprint ................. 41
headers ............................... 41
physical mounting ............. 41
Prototyping Board ............. 53
Rabbit 2000 DC characteristics ................................. 44
Rabbit 2000 timing diagram .............................. 43
relative pin 1 locations ...... 41
spectrum spreader ................. 30
subsystems
digital inputs and outputs .. 21
switching modes .................... 28
T
technical support ................... 12
U
USB/serial port converter ........ 9
Dynamic C settings ........... 11
user block
function calls
readUserBlock ............... 31
writeUserBlock .............. 31
RabbitCore RCM2300
SCHEMATICS
090-0119 RCM2300 Schematic
www.rabbit.com/documentation/schemat/090-0119.pdf
090-0122 RCM2200/RCM2300 Prototyping Board Schematic
www.rabbit.com/documentation/schemat/090-0122.pdf
090-0128 Programming Cable Schematic
www.rabbit.com/documentation/schemat/090-0128.pdf
You may use the URL information provided above to access the latest schematics directly.
User’s Manual
73