800 / 1000 Slip-On (2012

800 / 1000 Slip-On (2012
Installation Instructions
1.
Make sure the ATV is completely cool before starting
the installation. Make sure the ATV is secure on a level
surface and the parking brake is set.
2.
Loosen joint bolt and remove rear bumper.
3.
Remove rear bumper.
CAN-AM
Renegade 1000
Part # 005-324040xV
4.
**This product has not been tested with all available accessories and some
items may cause excessive heat. Excessive heat may cause damage to your
vehicle. Two Brothers Racing will not be responsible for damaged parts.
Warranty
Two Brothers Racing products are intended for closed course competition purposes only, and therefore are sold “as is”
without warranty. Two Brothers Racing specifically disclaims any warranties of merchantability or fitness for a particular
purpose and disclaims all responsibility for consequential and incidental damages or any other losses arising from the use
of these products or parts.
5.
Loosely install barrel clamp to slip tube end.
7.
Install TBR muffler assembly.
8.
Re-install rear bumper and use OEM bolts on top.
Remove OEM muffler.
IMPORTANT - PLEASE READ CAREFULLY
We recommend that this performance part be installed by a qualified
motorcycle technician. If you have any doubts as to your ability to install this
performance part, please consult with your local motorcycle dealer. Read all
instructions first before starting installation. Make sure the motorcycle and
exhaust system are completely cool before starting the installation. Be sure
to save all stock components for possible use later.
6.
Loosely attach TBR muffler to TBR slip tube.
Installation Instructions
9.
Use supplied bolts and OEM nuts on bottom mounts.
11. Tighten barreled clamp at joint.
CAN-AM
Renegade 1000
Part # 005-324040xV
12. Double check your work and make sure all bolts are
tightened and the exhaust is aligned correctly.
10. Tighten x-ring bolts.
13. Before you run the ATV, clean off all fingerprints
and dirt, as any oily residue will etch the metal and
become somewhat permanent when the system gets
hot. Run the ATV and enjoy. It is normal for some
white smoke to appear the first time you start the ATV.
This is packing/manufacturing oil from inside the pipe
burning off. Check for gaps or leaks. If you find a
leak, a little high temperature silicon sealant should
fix it. After 50 to 100 miles, recheck all fasteners for
tightness.
Care & Cleaning
Parts List
Qty.
Description
Part Number
1
1
2
1
2
2
1
Muffler Canister M-7 Stainless Steel
Stainless Steel S-Bend Slip-On 8x45mm Socket Head Cap Screw
61mm Barrel Clamp
8mm Lock Washer
X-Ring Kit
TBR Sticker Kit
005-324-209M
005-32404S
005-SH845
005-27-61MSH
005-WL8
005-7-2-3KIT
015-10212
Care & Cleaning
Keep system free of dirt and moisture. Store in a cool, dry place. Make sure vehicle is completely cool before maintenance.
Stainless Header System: Polished stainless steel pipes will turn a light golden hue after a few heat cycles, this is a normal characteristic of high quality stainless steel. Clean using a
mild water based spray cleaner. Always apply cleaner or polish with a soft, clean cloth.
Titanium Header System: Polished titanium pipes will experience color shift ranging from deep blue/purple through amber after a few heat cycles. This is a normal characteristic of high
quality titanium. Clean using a mild water based spray cleaner. Always apply cleaner or polish with a soft, clean cloth.
Polished Aluminum Canisters: Use an aluminum or mag wheel polish to restore the bright finish to factory spec.
Brushed Aluminum Canisters: Clean using a mild water based spray cleaner. Always apply cleaner or polish with a soft, clean cloth.
Carbon Fiber Canisters: Clean using a mild water based spray cleaner. Always apply cleaner or polish with a soft, clean cloth. Always make sure the fiberglass packing inside is in good
condition and not burned out, as exhaust heat inside an empty canister will deteriorate the carbon fiber sleeve.
TBR sells repack kits (Road - #005-10038, Offroad - #005-10038MX) that include everything you need to easily do it yourself.
Titanium Mufflers: For cleaning use a mild water based spray cleaner. Always apply cleaner or polish with a soft, clean cloth. Always make sure the fiberglass packing inside is in good
condition and not burned out, as exhaust heat inside an empty canister will deteriorate the carbon fiber sleeve.
TBR sells repack kits (Road - #005-10038, Offroad - #005-10038MX) that include everything you need to easily do it yourself.
Repack all road canisters every 3,000 miles. Part #005-10038
Repack all offroad canisters after every 10 hours of use. Part #005-10038MX
NEVER dyno test your bike with carbon fiber or titanium canisters installed - the intense heat and lack of cooling air can quickly burn through the canister material. Two Brothers Racing
does not provide a warranty for burned canisters.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement