Seismic Structural Attachments

Seismic Structural Attachments
Seismic Structural Attachments
Fig. 69 - Beam Clamp Retaining Strap (B-Line B3367)
Size Range: 3/8"-16 thru 3/4"-10 rod
4” (101.6mm) thru 16” (406.4mm) lengths
Note: longer lengths are available consult factory
Material: Pre-Galvanized Steel
Function: To offer more secure fastening of various types of
beam clamps to beam where danger of movement might be
expected. NFPA 13 requires the use of retaining straps with
all beam clamps installed in earthquake areas. Satisfies
requirements of NFPA 13.
Seismic Structural
Attachments
Important Note: Good installation practice of a retaining
strap requires that the strap be held tightly and securely to all
component parts of the assembly. Therefore a locking
mechanism of some kind, such as a hex nut will provide a
more secure reliable installation.
Approvals: Underwriters Laboratories Listed in the USA (UL)
and Canada (cUL). Approved for use with any listed beam
clamp. Included in our Seismic Restraints Catalog approved
by the state of California Office of Statewide Health Planning
and Development (OSHPD). For additional load, spacing and
placement information relating to OSHPD projects, please refer
to our Seismic Restraints System Guidelines.
Finish: Pre-Galvanized
Order By: Figure number, length (L), and finish.
Note: Minimum return on strap is 1” (25.4mm)
For Use With: See chart.
Hole Diameter
Part No.
in.
(mm)
For Use With
Length
69-3/8-L
7/16”
(11.1)
B3033-3/8, B3034-3/8, B3031-3/8,
65-3/8, 65XT-3/8, 66-3/8
Specify
69-1/2-L
9/16”
(14.3)
B3033-1/2, B3034-1/2, 65-1/2, 66-1/2
Specify
69-5/8-L
11/16”
(17.5)
B3033-5/8, 65-5/8, 66-5/8
Specify
69-3/4-L
13/16”
(20.6)
B3033-3/4
Specify
All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.
25
Seismic Bracing Products
Seismic Structural Attachments
Fig. 69R - Retrofit Capable Beam Clamp Retaining Strap
Size Range: 3/8"-16 & 1/2"-13 rod
4” (101,6mm) thru 16” (406.4mm) lengths
Note: longer lengths are available consult factory
Component of State of
California OSHPD Approved
Seismic Restraints System
Material: Pre-Galvanized Steel
Function: To offer more secure fastening of various types of beam
clamps to beam where danger of movement might be expected. NFPA
13 requires the use of retaining straps with all beam clamps installed in
earthquake areas. Satisfies requirements of NFPA 13.
Features: Beveled locking slot* is precisely formed to align with the
threaded section of a hanger rod or set screw and engage the unit
securely. May be used as shown in Section “A-A” or inverted. Allows
easy installation for new construction or retrofit applications.
A
A
Seismic Structural
Attachments
Important Note: Good installation practice of a retaining strap
requires that the strap be held tightly and securely to all component
parts of the assembly. Therefore the beveled locking slot of the Fig.
69R will provide a secure reliable installation.
Approvals: Underwriters Laboratories Listed in the USA (UL) and
Canada (cUL). Approved for use with any listed beam clamp. Included
in our Seismic Restraints Catalog approved by the state of California
Office of Statewide Health Planning and Development (OSHPD). For
additional load, spacing and placement information relating to OSHPD
projects, please refer to our Seismic Restraints System Guidelines.
A-A
Finish: Pre-Galvanized
Order By: Figure number, length, and finish.
Note: Minimum return on strap is 1” (25.4mm)
For Use With: See chart.
* Patent #5,947,424
Slot Width
Part No.
in.
69R-3/8-L
7/16”
(mm)
For Use With
Length
(30.1)
B3033-3/8, B3034-3/8, B3031-3/8,
Specify
65-3/8, 65XT-3/8, 66-3/8
69R-1/2-L
9/16”
(30.1)
B3033-1/2, B3034-1/2, 65-1/2, 66-1/2
Specify
All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.
Seismic Bracing Products
26
Seismic Structural Attachments
Fig. 109A - Concrete Deck Insert - Hanger Application
Component of State of
California OSHPD Approved
Seismic Restraints System
Size Range: 3/8"-16 thru 7/8"-9 rod
Material: Steel
Function: For use in metal deck formed concrete to attach hanger
rods. Allows for pre-positioning of hanger rods in poured concrete
decks.
Approvals: 3/8" - 5/8" rod size is Underwriters Laboratories Listed in the
USA (UL) and Canada (cUL). Included in our Seismic Restraints Catalog
approved by the state of California Office of Statewide Health Planning
and Development (OSHPD). For additional load, spacing and placement
information relating to OSHPD projects, please refer to our Seismic
Restraints System Guidelines.
Standard Bolt Length
8” (203.2mm)
Finish: Plate: Plain Steel. Rod: Electro-Galvanized. Contact B-Line for
alternative finishes and materials.
25/8”
(66.7mm)
1” (25.4mm)
Minimum
1î
A
Fig. 109A
12” (305mm)
Minimum
12” (305mm)
Minimum
1” (25.4mm)
Minimum
Part No.
in.
(mm)
Max. Hanger
Spacing
in.
(m)
Edge of Concrete
Edge of Concrete
Max.
Pipe Size
Fig. 109A
Max. Recommended
Load
Approx.
Wt./100
lbs.
(kN)
109A-3/8
3/8"-16
4" (101.6)
15’-0” (4.57)
572
(2.54)
67.0 (30.4)
109A-1/2
1/2"-13
8" (203.2)
15’-0” (4.57)
579
(2.57)
69.0 (31.3)
109A-5/8
5/8"-11
Contact B-Line
715
(3.18)
71.0 (32.2)
109A-3/4
3/4"-10
Contact B-Line
1000 (4.45)
213.0 (96.6)
109A-7/8
7/8"-9
Contact B-Line
1000 (4.45)
217.0 (98.4)
Max. Recommended Loads shown include safety factor of 5.
Weight is based on the standard bolt length.
lbs.
1” (25.4mm)
Minimum
25/8”
(66.7mm)
25/8”
(66.7mm)
Fig. 109A
Rod
Size
12” (305mm)
Minimum
1” (25.4mm)
Minimum
25/8”
(66.7mm)
Edge of Concrete
Seismic Structural
Attachments
Order By: Figure number, rod size and finish. Contact B-Line for
custom rod lengths.
(kg)
1” (25.4mm)
Minimum
Fig. 109A
NOTES:
1. Mounting holes are standard. If the
plate is not mechanically secured to
the deck ribs, a jam nut is required
to prevent the anchor bolt from laying
over when concrete is poured. There
is no structural strength added from
the use of a mechanical fastener to
hold the product in place before the
pour.
2. Minimum spacing between inserts
shall be not less than 41⁄2" (114.3mm)
for 3⁄8" and 6" (1152.4mm) for 1⁄2"
All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.
Revised 11/4/2014
27
Seismic Bracing Products
Seismic Structural Attachments
Fig. 109A - Concrete Deck Insert - Brace Application
Component of State of
California OSHPD Approved
Seismic Restraints System
Size Range: 3/8"-16 thru 7/8"-9 rod
Material: Steel
Function: For use in metal deck formed concrete to attach hanger rods.
Allows for pre-positioning of hanger rods in poured concrete decks.
Approvals: Included in our Seismic Restraints Catalog approved by
the state of California Office of Statewide Health Planning and
Development (OSHPD). For additional load, spacing and placement
information relating to OSHPD projects, please refer to our Seismic
Restraints System Guidelines. Hangers certified by a registered
professional engineer to Section 6-1.1 of NFPA #13 (1999) and
Section 9.1.1.2. of NFPA 13 (2002).
Standard
Bolt Length
8” (203.2mm)
Finish: Plate: Plain Steel. Rod: Electro-Galvanized. Contact B-Line for
alternative finishes and materials.
Seismic
Structural
Attachments
Order By: Figure number, rod size and finish. Contact B-Line for
custom rod lengths.
Qualifies as an acceptable alternate seismic brace fastener per Section
9.3.5.9.6 Certification calculations for this application are available upon
request. See dimensions and installation Detail below.
12” (305mm)
Minimum
12” (305mm)
Minimum
1” (25.4mm)
Minimum
1” (25.4mm)
Minimum
‘D’
1” (25.4mm)
Minimum
12” (305mm)
Minimum
‘D’
Edge of
Concrete
Edge of
Concrete
Edge of
Concrete
‘D’
Fig. 109A
1” (25.4mm)
Minimum
Fig. 109A
Fig. 109A
1” (25.4mm)
‘D’ Minimum
1î
Rod
Size
Max. Horizontal Load
Brace At 45°
Part No.
109A-3/8
109A-1/2
109A-5/8
109A-3/4
109A-7/8
3/8"-16
1/2"-13
5/8"-11
3/4"-10
7/8"-9
‘D’ Min. Anchor
Embedment Depth
Approx.
Wt./100
lbs.
(kN)
in.
(mm)
lbs.
(kg)
560
660
680
700
700
(2.49)
25/8"
25/8"
25/8"
25/8"
25/8"
(66.7)
67.0
69.0
71.0
213.0
217.0
(30.4)
(2.93)
(3.02)
(3.11)
(3.11)
(66.7)
(66.7)
(66.7)
(66.7)
(31.3)
(32.2)
(96.6)
(98.4)
Seismic bracing design load calculated in compliance with the requirements of IBC 2009 / CBC 2010.
Rod
Size
Max. Horizontal Load
Brace At 45°
Part No.
109A-3/8
109A-1/2
109A-5/8
109A-3/4
109A-7/8
3/8"-16
1/2"-13
5/8"-11
3/4"-10
7/8"-9
‘D’ Min. Anchor
Embedment Depth
Approx.
Wt./100
lbs.
(kN)
in.
(mm)
lbs.
(kg)
337
395
395
395
395
(1.50)
25/8"
25/8"
25/8"
25/8"
25/8"
(66.7)
67.0
69.0
71.0
213.0
217.0
(30.4)
(1.75)
(1.75)
(1.75)
(1.75)
(66.7)
(66.7)
(66.7)
(66.7)
A
Fig. 109A
(31.3)
(32.2)
(96.6)
NOTES:
1. Mounting holes are standard. If the
plate is not mechanically secured to
the deck ribs, a jam nut is required
to prevent the anchor bolt from laying
over when concrete is poured. There
is no structural strength added from
the use of a mechanical fastener to
hold the product in place before the
pour.
2. Minimum spacing between inserts
shall be not less than 41⁄2" (114.3mm)
for 3⁄8" and 6" (1152.4mm) for 1⁄2"
(98.4)
Seismic bracing design load calculated in compliance with the requirements of IBC 2012 / CBC 2013.
All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.
Seismic Bracing Products
28
Revised 8/8/2014
Seismic Structural Attachments
Fig. 109AF - Concrete Spot Insert - Hanger Application (B-Line B2501)
Component of State of
California OSHPD Approved
Seismic Restraints System
Size Range: 3/8"-16 thru 7/8"-9 rod
Material: Steel
Function: Designed to be embedded in concrete to provide a point
of support.
Approvals: Underwriters Laboratories Listed in the USA (UL) and
Canada (cUL) for 3/8" and 1/2". Included in our Seismic Restraints Catalog
approved by the state of California Office of Statewide Health Planning
and Development (OSHPD). For additional load, spacing and placement
information relating to OSHPD projects, please refer to our Seismic
Restraints System Guidelines.
Finish: Electro-Galvanized anchor bolt with Electro-Galvanized hardware
and plate.
Order By: Figure number, rod size and finish.
Seismic Structural
Attachments
Note: The hex or jam nut has NO value in determining the loads.
Their function is to assist in locking the coupling snug to the bottom of
the deck form preventing the concrete from leaking into the coupling
threads. Any other suitable locking device may be substituted if desired.
Qualifies as an acceptable alternate seismic brace fastener per Section
9.3.5.9.6 Certification calculations for this application are available upon
request. See dimensions and installation Detail below.
Anchor Bolt
ASTM A307
E
Rod Coupling
Edge of
Concrete
Embedment
Depth E
Mounting Hole for
Securing to Form
Part No.
Design Load 45°
DE Min.
Rod
Size
Part No.
in.
DE
Min.
(mm)
in.
(mm)
Approx.
Wt./100
lbs.
(kg)
109AF-3/8
31/2” (88.9)
2” (50.8)
38.1 (17.3)
109AF-1/2
31/2” (88.9)
2” (50.8)
54.7 (24.8)
109AF-5/8
4” (101.6)
2” (50.8)
82.2 (37.3)
109AF-3/4
4” (101.6)
21/2” (63.6)
113.8 (51.6)
109AF-7/8
4” (101.6)
6” (152.4)
130.6 (59.2)
Design Load Vertical
Hard Rock
Light Wt.
Design Load Shear
Hard Rock
Light Wt.
Design Load 45°
Hard Rock
Light Wt.
lbs.
(kN)
lbs.
(kN)
lbs.
(kN)
lbs.
(kN)
lbs.
(kN)
lbs.
(kN)
1255 (55.82)
735
(3.28)
978
(4.35)
733
(3.26)
777
(3.45)
525
(2.33)
2321 (10.32)
1392 (6.19)
978
(4.35)
733
(3.26)
980
(4.36)
679
(3.02)
780
(3.47)
468
(2.08)
1278 (5.68)
958
(4.26)
688
(3.06)
445
(1,98)
1346 (5.99)
806
(3.58)
1278 (5.68)
958
(4.26)
927
(4.12)
619
(2,75)
1391 (6.19)
1278 (5.68)
958
(4.26)
1166 (5.18)
803
(3,57)
109AF-3/8
3/8"-16
109AF-1/2
1/2"-13
109AF-5/8
5/8"-11
109AF-3/4
3/4"-10
109AF-7/8
7/8"-9
2321 (10.32)
Max. Recommended Loads shown include safety factor of 5.
All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.
29
Seismic Bracing Products
Seismic Structural Attachments
Fig. 109AF - Concrete Insert - Brace Application (B-Line B2501)
Component of State of
California OSHPD Approved
Seismic Restraints System
Size Range: 3/8"-16 thru 7/8"-9 rod
Material: Steel
Function: Designed to be embedded in concrete to provide a point
of support.
Finish: Electro-Galvanized anchor bolt with Electro-Galvanized
hardware and plate.
Anchor Bolt
ASTM A307
Order By: Figure number, rod size and finish.
Note: The hex or jam nut has NO value in determining the loads.
Their function is to assist in locking the coupling snug to the bottom of
the deck form preventing the concrete from leaking into the coupling
threads. Any other suitable locking device may be substituted if
desired.
E
Rod Coupling
Edge of Concrete
Mounting Hole for
Securing to Form
Qualifies as an acceptable alternate seismic brace fastener per Section
9.3.5.9.6 Certification calculations for this application are available
upon request. See dimensions and installation Detail below.
Design Load
45°
DE Min.
Rod
Size
Part No.
109AF-3/8
109AF-1/2
109AF-1/2
109AF-5/8
109AF-5/8
109AF-3/4
109AF-3/4
109AF-7/8
109AF-7/8
3/8"-16
1/2"-13
1/2"-13
5/8"-11
5/8"-11
3/4"-10
3/4"-10
7/8"-9
7/8"-9
Max. Horizontal Seismic
Load With Brace At 45°
Embedment
Depth E
DE
Min.
Approx.
Wt./100
in.
(mm)
in.
(mm)
in.
(mm)
Lbs.
(kg)
925
925
950
1250
1424
1275
1424
1330
1424
(4.11)
31/2”
31/2”
4”
4”
5”
4”
6”
4”
7”
(88.9)
2”
2”
2”
2”
2”
2”
2”
2”
2”
(50.8)
38.1
54.7
54.7
82.2
82.2
113.8
113.8
130.6
130.6
(17.3)
(4.11)
(4.22)
(5.56)
(6.33)
(5.67)
(6.33)
(5.91)
(6.33)
(88.9)
(101.6)
(101.6)
(127.0)
(101.6)
(152.4)
(101.6)
(177.8)
(50.8)
(50.8)
(50.8)
(50.8)
(50.8)
(50.8)
(50.8)
(50.8)
(24.8)
(24.8)
(37.3)
(37.3)
(51.6)
(51.6)
(59.2)
(59.2)
Seismic bracing design load calculated in compliance with the requirements of IBC 2009 / CBC 2010.
Rod
Size
Part No.
109AF-3/8
109AF-1/2
109AF-1/2
109AF-5/8
109AF-5/8
109AF-3/4
109AF-3/4
109AF-7/8
109AF-7/8
3/8"-16
1/2"-13
1/2"-13
5/8"-11
5/8"-11
3/4"-10
3/4"-10
7/8"-9
7/8"-9
Max. Horizontal Seismic
Load With Brace At 45°
Embedment
Depth E
DE
Min.
Approx.
Wt./100
in.
(mm)
in.
(mm)
in.
(mm)
Lbs.
(kg)
781
781
807
999
1275
1029
1424
1074
1424
(3.47)
31/2”
31/2”
4”
4”
5”
4”
6”
4”
7”
(88.9)
2”
2”
2”
2”
2”
2”
2”
2”
2”
(50.8)
38.1
54.7
54.7
82.2
82.2
113.8
113.8
130.6
130.6
(17.3)
(3.47)
(3.59)
(4.44)
(5.67)
(4.57)
(6.33)
(4.78)
(6.33)
(88.9)
(101.6)
(101.6)
(127.0)
(101.6)
(152.4)
(101.6)
(177.8)
(50.8)
(50.8)
(50.8)
(50.8)
(50.8)
(50.8)
(50.8)
(50.8)
(24.8)
(24.8)
(37.3)
(37.3)
(51.6)
(51.6)
(59.2)
(59.2)
Seismic bracing design load calculated in compliance with the requirements of IBC 2012 / CBC 2013.
All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.
Seismic Bracing Products
30
Revised 8/8/2014
Seismic Structural
Attachments
Approvals: Included in our Seismic Restraints Catalog approved by
the state of California Office of Statewide Health Planning and
Development (OSHPD). For additional load, spacing and placement
information relating to OSHPD projects, please refer to our Seismic
Restraints System Guidelines. Hangers certified by a registered
professional engineer to Section 6-1.1 of NFPA #13 (1999) and
Section 9.1.1.2. of NFPA 13 (2002).
Seismic Structural Attachments
B2505 thru B2508 - Spot Insert
End Caps
Material: Steel (Stainless steel available on B2505 only)
Channel
Size
Standard Finish: Plain or Pre-Galvanized
Function: Designed to be embedded in concrete to attach 1/4"-20 to
7/8"-9 hanger rods.
How to Install: Attach concrete insert to forms and install reinforcing
rods as required. After forms are dismantled, the channel nut can be
installed and the rod fastened to the nut. The rod should touch the
inside top of the insert.
25/8"
(66.7)
51/16"
Approvals: Underwriters Laboratories Listed. Conforms to Federal
Specification WW-H-171E & A-A-1192A, Type 18 and Manufacturers
Standardization Society ANSI/MSS SP-69 & SP-58, Type 18.
(128.6)
Styrofoam Filled
Seismic Structural
Attachments
Order By: Figure number and finish. When supporting
10" (254mm) pipe, order B2505 Insert with 5/8"-11 channel nuts.
Note: For appropriate channel nut selection, see bottom of page.
Before installation ensure that concrete is sufficient to carry the
load.
Part No.
Channel
Size
End Cap
Part No.
Lbs.
Design Load
B2505
B22
B3322
1200
B2506
B32
B3332
B2507
B42
B2508
B52
Max. Pipe Size
(kN)
in.
Approx. Wt./100
(mm)
Lbs.
(kg)
(5.34)
10" (250)
96
(43.5)
1000
(4.45)
8"
(200)
88
(39.9)
B3342
1000
(4.45)
8"
(200)
77
(34.9)
B3352
1000
(4.45)
8"
(200)
69
(31.3)
Channel Nuts
For B2505 thru B2508, B2503, B22I, B32I, & B52I
Part No.
Thread Size Fits Channel Sizes
Nut Thickness
in.
N228WO
3/8”-16
N225WO
1/2”-13
N525WO
(mm)
Slip
Pull-Out
Lbs.
(N)
Lbs
(N)
Wt./C
Lbs.
kg
(4.22)
B22I, B32I, B52I
3/8”
(9.5)
800
(3560)
1100 (4890)
9.3
B22I, B32I
1/2”
(12.7)
1500 (6670)
2000 (8900)
11.6 (5.26)
1/2”-13
B22I, B32I, B52I
3/8”
(9.5)
1500 (6670)
1500 (6670)
8.8
N255WO
5/8”-11
B22I, B32I
1/2”
(12.7)
1500 (6670)
2000 (8900)
16.4 (7.44)
N555WO
5/8”-11
B22I, B32I, B52I
3/8”
(9.5)
1500 (6670)
1500 (6670)
10.2 (4.62)
N275WO
3/4”-10
B22I, B32I
1/2”
(12.7)
1500 (6670)
2000 (8900)
14.5 (6.58)
N575WO
3/4”-10
B22I, B32I, B52I
3/8”
(9.5)
1500 (6670)
1500 (6670)
8.8
N278WO
7/8”-9
B22I, B32I
1/2”
(12.7)
1500 (6670)
1500 (6670)
12.5 (5.67)
(3.99)
(3.99)
All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.
31
Seismic Bracing Products
Seismic Structural Attachments
Fig. B2503 - Heavy Duty Spot Insert
Material: Steel
Standard Finish: Electro-Galvanized
Function: Designed to be embedded in concrete where heavy loads
are required in curtain wall applications. Styrofoam end caps prevent
concrete seepage into the channel.
How to Install: Attach concrete insert to forms and install reinforcing
rods as required. After forms are dismantled, the channel nut can be
installed and the rod fastened to the nut. The rod should touch the
inside top of the insert.
Approvals: Conforms to Federal Specification WW-H-171E &
A-A-1192A, Type 18 and Manufacturers Standardization Society
ANSI/MSS SP-69 & SP-58, Type 18.
Seismic Structural
Attachments
Design Load: 5000 Lbs. (22.2kN).
Loading based on two N225 channel nuts spaced 3” (76.2mm) on
center and a minimum of 2” (50.8mm) from the end of the insert.
Weight: Approx. Wt./100 - 42 Lbs. (19.0kg)
Order By: Figure number and finish. Channel nuts are sold
separately, see page 31 for appropriate selection.
2"
5/32" (4.0)
(50.8)
Dia. Nail Holes
8"
(203.2)
51/2”
(139.7)
15/8”
12"
(41.3)
(304.8)
Styrofoam
End Caps
15/8 ”
(41.3)
All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.
Seismic Bracing Products
32
Seismic Structural Attachments
25/8”
Fig. B22I - Continuous Concrete Insert
(66.7)
15/8 ”
(41.3)
Material: Steel
Standard Finish: Plain, Pre-Galvanized, or Hot-Dip Galvanized
Function: Concrete insert should be secured to forms on
16” (406.4mm) to 24” (609.6mm) intervals.
15/8 ”
(41.3)
How to Install: Attach concrete insert to forms and install
reinforcing rods as required. After forms are dismantled, the
channel nut can be installed and the rod fastened to the nut.
The rod should touch the inside top of the insert.
B3322
End Cap
Styrofoam
Filler
B22-I-3 thru B22-I-8
Approvals: Conforms to Federal Specification WW-H-171E &
A-A-1192A, Type 18 and Manufacturers Standardization Society
ANSI/MSS SP-69 & SP-58, Type 18.
4”
(101.6)
15/8 ”
11/2”
Seismic Structural
Attachments
Design Load: 2000 Lbs. (8.89kN) per foot for B22-I-12 thru
B22-I-240 in 3000 psi concrete. Loads concentrated within the
last 2” (50.8mm) of inserts 8” (203.2mm) and longer should not
exceed 1000 Lbs. (4.45kN).
(41.3)
(38.1)
3/4”
(19.0)
Order By: Figure number and finish. Channel nuts are sold
separately, see page 31 for appropriate selection.
To order inserts without styrofoam and end caps add insert only
to the part number.
.188” (4.8) Knockouts
for Nailing Inserts
To Forms
31/8”
11/16”
(79.4)
(17.4)
15/8”
B22-I-12 thru B22-I-240
(41.3)
Length
Part No.
in.
B22-I-3
B22-I-4
B22-I-6
B22-I-8
3”
4”
6”
8”
Approx. Wt./100
Lbs.
(kg)
Lbs.
(kN)
(76)
72
88
120
152
(32.6)
500
800
1000
1200
(2.22)
(101)
(152)
(203)
Length
Part No.
B22-I-12
B22-I-16
B22-I-20
B22-I-24
B22-I-32
B22-I-36
B22-I-40
B22-I-48
B22-I-60
B22-I-72
B22-I-84
B22-I-96
B22-I-108
B22-I-120
B22-I-144
B22-I-168
B22-I-192
B22-I-216
B22-I-240
Design Load
(mm)
(39.9)
(54.4)
(68.9)
(mm)
Lbs.
(kg)
12”
16”
20”
24”
32”
36”
40”
48”
60”
72”
84”
96”
108”
120”
144”
168”
192”
216”
240”
(305)
224
289
353
420
553
620
686
820
1018
1218
1417
1616
1816
2016
2416
2816
3216
3616
4016
(101.6)
(508)
(609)
(813)
(914)
(1016)
(1219)
(1524)
(1829)
(2133)
(2438)
(2743)
(3048)
(3657)
(4267)
(4877)
(5486)
(6096)
(4.45)
(5.34)
Approx. Wt./100
in.
(406)
(3.56)
(131.1)
Styrofoam
Filler
Material:
12 Gauge (2.6)
(160.1)
(190.5)
(250.8)
(281.2)
B205
End Cap
(311.1)
(371.9)
(461.7)
(552.5)
(642.7)
(733.0)
(823.7)
(914.4)
(1095.9)
(1277.3)
(1458.7)
(1640.2)
(1821.6)
All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.
33
Seismic Bracing Products
Seismic Structural Attachments
25/8”
Fig. B32I - Continuous Concrete Insert
15/8”
(66.7)
(41.3)
Material: Steel
Standard Finish: Plain, Pre-Galvanized, or Hot-Dip Galvanized
Function: Concrete insert should be secured to forms on
16” (406.4mm) to 24” (609.6mm) intervals.
13/8”
(34.9)
How to Install: Attach concrete insert to forms and install
reinforcing rods as required. After forms are dismantled, the
channel nut can be installed and the rod fastened to the nut.
The rod should touch the inside top of the insert.
B3332
End Cap
B32-I-3 thru B32-I-8
Approvals: Conforms to Federal Specification WW-H-171E &
A-A-1192A, Type 18 and Manufacturers Standardization Society
ANSI/MSS SP-69 & SP-58, Type 18.
4”
(101.6)
15/8”
11/2”
(41.3)
(38.1)
3/4”
(19.0)
Order By: Figure number and finish. Channel nuts are sold
separately, see page 31 for appropriate selection.
To order inserts without styrofoam and end caps add insert only
to the part number.
.188” (4.8) Knockouts
for Nailing Inserts
To Forms
27/8”
11/16”
(73.0)
(17.4)
13/8”
B32-I-12 thru B32-I-240
(34.9)
Length
in.
B32-I-3
B32-I-4
B32-I-6
B32-I-8
3”
4”
6”
8”
Approx. Wt./100
Lbs.
(kg)
Lbs.
(kN)
(76)
65
80
108
137
(29.5)
500
800
1000
1200
(2.22)
(101)
(152)
(203)
Length
Part No.
B32-I-12
B32-I-16
B32-I-20
B32-I-24
B32-I-32
B32-I-36
B32-I-40
B32-I-48
B32-I-60
B32-I-72
B32-I-84
B32-I-96
B32-I-108
B32-I-120
B32-I-144
B32-I-168
B32-I-192
B32-I-216
B32-I-240
Design Load
(mm)
(36.3)
(49.0)
(62.1)
(3.56)
(4.45)
(5.34)
Approx. Wt./100
in.
(mm)
Lbs.
(kg)
12”
16”
20”
24”
32”
36”
40”
48”
60”
72”
84”
96”
108”
120”
144”
168”
192”
216”
240”
(305)
202
262
316
376
496
556
616
736
915
1095
1274
1453
1633
1813
2173
2533
2893
3253
3613
(91.6)
(406)
(508)
(609)
(813)
(914)
(1016)
(1219)
(1524)
(1829)
(2133)
(2438)
(2743)
(3048)
(3657)
(4267)
(4877)
(5486)
(6096)
(118.8)
Styrofoam
Filler
Material:
12 Gauge (2.6)
(143.3)
(170.5)
(225.0)
(252.2)
(279.4)
B206
End Cap
(333.8)
(415.0)
(496.7)
(577.9)
(659.0)
(740.7)
(822.3)
(985.6)
(1148.9)
(1312.2)
(1475.5)
(1638.8)
All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.
Seismic Bracing Products
34
Seismic Structural
Attachments
Design Load: 2000 Lbs. (8.89kN) per foot for B32-I-12 thru
B32-I-240 in 3000 psi concrete. Loads concentrated within the
last 2” (50.8mm) of inserts 8” (203.2mm) and longer should not
exceed 1000 Lbs. (4.45kN).
Part No.
Styrofoam
Filler
Seismic Structural Attachments
29/16”
Fig. B52I - Continuous Concrete Insert
15/8”
(65.1)
(41.3)
Material: Steel
Standard Finish: Plain, Pre-Galvanized, or Hot-Dip Galvanized
Function: Concrete insert should be secured to forms on
16” (406.4mm) to 24” (609.6mm) intervals.
13/16”
(20.6)
How to Install: Attach concrete insert to forms and install
reinforcing rods as required. After forms are dismantled, the
channel nut can be installed and the rod fastened to the nut.
The rod should touch the inside top of the insert.
B3352
End Cap
Styrofoam
Filler
B52-I-3 thru B52-I-8
Approvals: Conforms to Federal Specification WW-H-171E &
A-A-1192A, Type 18 and Manufacturers Standardization Society
ANSI/MSS SP-69 & SP-58, Type 18.
4”
(101.6)
15/8”
11/2”
Seismic Structural
Attachments
Design Load: 1500 Lbs. (6.67kN) per foot for B52-I-12 thru
B52-I-240 in 3000 psi concrete. Loads concentrated within the
last 2” (50.8mm) of inserts 8” (203.2mm) and longer should not
exceed 750 Lbs. (3.33kN).
(41.3)
(38.1)
3/4”
(19.0)
Order By: Figure number and finish. Channel nuts are sold
separately, see page 31 for appropriate selection.
To order inserts without styrofoam and end caps add insert only
to the part number.
.188” (4.8) Knockouts
for Nailing Inserts
To Forms
25/16”
11/16”
(58.7)
(17.4)
13/16”
B52-I-12 thru B52-I-240
(20.6)
Length
Part No.
in.
B52-I-3
B52-I-4
B52-I-6
B52-I-8
3”
4”
6”
8”
Approx. Wt./100
Lbs.
(kg)
Lbs.
(kN)
(76)
53
63
85
106
(24.0)
400
500
750
1000
(1.78)
(101)
(152)
(203)
Length
Part No.
B52-I-12
B52-I-16
B52-I-20
B52-I-24
B52-I-32
B52-I-36
B52-I-40
B52-I-48
B52-I-60
B52-I-72
B52-I-84
B52-I-96
B52-I-108
B52-I-120
B52-I-144
B52-I-168
B52-I-192
B52-I-216
B52-I-240
Design Load
(mm)
(28.6)
(38.5)
(48.1)
(2.22)
(3.33)
(4.45)
Approx. Wt./100
in.
(mm)
12”
16”
20”
24”
32”
36”
40”
48”
60”
72”
84”
96”
108”
120”
144”
168”
192”
216”
240”
(305)
(406)
(508)
(609)
(813)
(914)
(1016)
(1219)
(1524)
(1829)
(2133)
(2438)
(2743)
(3048)
(3657)
(4267)
(4877)
(5486)
(6096)
Lbs.
(kg)
157
(71.2)
202
(91.6)
237 (107.5)
282 (127.9)
373 (169.2)
419 (190.0)
464 (210.4)
556 (252.2)
692 (313.9)
829 (376.0)
965 (437.7)
1107 (502.1)
1237 (561.1)
1374 (623.2)
1648 (747.5)
1922 (871.8)
2196 (996.1)
2470 (1120.4)
2744 (1244.6)
Styrofoam
Filler
Material:
12 Gauge (2.6)
B220
End Cap
All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.
35
Seismic Bracing Products
Seismic Structural Attachments
Fig. 75 - Swivel Attachment
Size Range: — 3/8"-16 Rod Attachment
Material: Steel
Function: Three recommended applications for this product:
• May be used as a Branch Line Restraint for structural attachment to
anchor bolt, beam clamp, etc.
• May be used as an upper attachment with short hanger rod to
omit seismic bracing.
• May be used in a pitched or sloped roof application, to meet
requirements of NFPA 13 (2013) 9.1.2.6.
Approvals: Underwriters Laboratories Listed in the USA (UL) and
Canada (cUL) to support up to 4" (100mm) pipe.
Seismic Structural
Attachments
Finish: Electro-Galvanized
Weight: Approx. Wt./100 - 13.3 Lbs. (6.0kg)
Order By: Figure number
Patent: #7,887,248
Fig. 78 All Steel
Ceiling Plate
Fig. 75 Swivel
Attachment
Fig. 200
“Trimline”
Adjustable
Band Hanger
All Threaded Rod
Fig. 25 Surge Restrainer
May be used as a structural attachment
component of a branch line restraint
ed
ch
Pit
of
Ro
Fig. 65XT Reversible
Beam Clamp
W-Beam
Fig. 75 Swivel
Attachment
All
Threaded
Rod
May be used with a pitched roof
application, to meet requirements of
NFPA 13 (2010) Sec. 9.1.2.5.
All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.
Seismic Bracing Products
36
Seismic Structural Attachments
Fig. 800 - Adjustable Sway Brace Attachment to Steel
Size Range: 4" (100mm) thru 18" (450mm) beam width
Material: Steel
Function: Seismic brace attachment to steel.
Component of State of
California OSHPD Approved
Seismic Restraints System
Features: This product’s design incorporates a concentric attachment point which is
critical to the performance of structural seismic connections. NFPA 13 indicates the
importance of concentric loading of connections and fasteners. Permits secure
connection to steel where drilling and/or welding of brace connection could present
structural issues.
Installation Instructions: Fig. 800 is the structural attachment component of a
longitudinal or lateral sway brace assembly. It is intended to be combined with our
transitional attachment, "bracing pipe" and our "braced pipe" attachment to form a
complete bracing assembly.
NFPA 13, FM DS 2-8, and/or OSHPD guidelines should be followed.
Seismic Structural
Attachments
To Install: Place the Fig. 800 on the steel beam, tighten the cone point set bolts
on flange until the heads break off. Tighten hex head bolts into clamp body until lock
washers are fully flat. Attach other transitional attachment fitting, Fig. 909, 910, 980,
or 986. Transitional fitting attachment can pivot for adjustment to proper brace angle.
Set Bolts & Hardware
Included
Approvals: Underwriters Laboratories Listed in the USA (UL) and Canada (cUL).
Approved by Factory Mutual Engineering (FM). Included in our Seismic Restraints
Catalog approved by the State of California Office of Statewide Health Planning and
Development (OSHPD). For additional load, spacing and placement information
relating to OSHPD projects, please refer to our Seismic Restraint Systems Guidelines.
Finish: Plain or Electro-Galvanized. Contact B-Line for alternative finishes and
materials.
Order By: Figure number, type number and size number.
Fits Beam
Flange Width
Part No.
800-1
800-2
800-3
800-4
800-5
800-6
800-7
in.
(mm)
4”-6”
6”-8”
8”-10”
10”-12”
12”-14”
14”-16”
16”-18”
(101.6-152.4)
(152.4-203.2)
(203.2-254.0)
(304.8-355.6)
Shown with Fig. 980
brace fitting to pipe brace
(Across Beam)
(355.6-406.4)
(406.4-457.2)
Fits Beam
Type
Shown with Fig. 980
brace fitting to pipe brace
(Along Beam)
(254.0-304.8)
Flange Thickness
in.
(mm)
1
Up to 3/4”
(Up to 19.0)
2
3/4” to 11/4”
(19.0 to 31.7)
Max. Horizontal
Design Loads (cULus)
Along
Across
Beam
Beam
lbs./(kN)
lbs./(kN)
Max. Horizontal Design Loads (FM)
Laterial - Parallel to Structural Member
30°-44°
lbs./(kN)
45°-59°
lbs./(kN)
60°-74° 75°-90°
lbs./(kN) lbs./(kN)
Longitudinal - Perpendicular to Structural Member
30°-44°
lbs./(kN)
45°-59°
lbs./(kN)
60°-74° 75°-90°
lbs./(kN) lbs./(kN)
1265
2015
1430
1970
1980
NR
930
1310
1610
1800
(5.62)
(8.96)
(6.36)
(8.76)
(8.81)
(NR)
(4.13)
(5.82)
(7.16)
(8.00)
1265
2015
NR
NR
NR
NR
NR
NR
NR
NR
(5.62)
(8.96)
(NR)
(NR)
(NR)
(NR)
(NR)
(NR)
(NR)
(NR)
FM Approved design loads are based on ASD design method.
Eaton’s B-Line Business seismic bracing components are designed to be compatible only with other B-Line bracing components,
resulting in a listed seismic bracing assembly. B-Line’s warranty for seismic bracing components will be the warranty provided in
B-Line’s standard terms and conditions of sale made available by B-Line, except that, in addition to the other exclusions from
B-Line’s warranty, Eaton’s B-line Business makes no warranty relating to B-Line’s seismic bracing components that are combined
with products not provided by Eaton’s B-Line Business.
All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.
37
Seismic Bracing Products
Seismic Structural Attachments
Fig. 825 - Bar Joist Sway Brace Attachment To Steel
Component of State of
California OSHPD Approved
Seismic Restraints System
Size Range: Fits up to 3/8” (9.5mm) thick structural steel member.
Accommodates all Fig. 900 Series sway brace attachments.
Material: Steel
Function: To attach sway brace assemblies and/or hanger
assemblies to structural steel members.
3/8"
(9.5)
Features: This product’s design incorporates a concentric
attachment point which is critical to the performance of
structural seismic connections. NFPA 13 indicates the
importance of concentric loading of connections and
fasteners. Permits secure non-friction connection without
drilling or welding. Unique design reinforces point of
connection to joist. Break off head set bolt design assures verification of proper
installation torque (min. 31 ft.-lbs.).
Approvals: Underwriters Laboratories Listed in the USA (UL) and Canada (cUL).
Approved by Factory Mutual Engineering (FM). Included in our Seismic Restraints
Catalog approved by the State of California Office of Statewide Health Planning and
Development (OSHPD). For additional load, spacing and placement information
relating to OSHPD projects, please refer to our Seismic Restraint Systems Guidelines.
Installation Instructions: Fig. 825 is the structural attachment component
of a longitudinal or lateral sway brace assembly. It is intended to be combined
with a TOLCO transitional attachment, "bracing pipe" and a TOLCO "braced pipe"
attachment, to form a complete bracing assembly.
NFPA 13, FM DS 2-8, and/or OSHPD guidelines should be followed.
Seismic Structural
Attachments
Set Bolts & Hardware
Included
Top View
1”
(25.4mm)
1/2”
Bolt & Nut
Furnished
Fig. 825
To Install: Place the Fig. 825 on the steel beam, tighten the cone point set bolts
until heads break off. Attach other TOLCO transitional attachment fitting, Fig. 909,
910, 980, or 986. Transitional fitting attachment can pivot for adjustment to proper
brace angle.
Fig. 980
Finish: Plain or Electro-Galvanized. Contact B-Line for alternative finishes and
materials.
Approx. Wt./100: 247.5 Lbs. (112.2kg)
Fig. 825
Order By: Figure number and finish
US Patent #6,098,942,
Canada Patent #2,286,659
Fig. 1000
Side View
Fig. 980
Fig. 825
Fig. 980
Fig. 4L
Max. Horizontal Design Load (UL)
2015 lbs. (8.96kN)
UL Listed as Hanger Attachment for
6” (150mm) Pipe at Maximum Spacing
Fig. 1001
Fig. 825
Max. Horizontal Design Loads (FM)
3/8” Thick Flange
Maximum
Lateral - Parallel to
Structural Member
Maximum
3/8” Thick Flange
Longitudinal Perpendicular to
Structural Member
30°-44°
lbs. / (kN)
45°-59°
lbs. / (kN)
60°-74°
lbs. / (kN)
75°-90°
lbs. / (kN)
990
1360
1670
1860
(4.40)
(6.05)
(7.43)
(8.27)
460
630
770
860
(2.04)
(2.80)
(3.42)
(3.82)
Fig. 980
I-Beam
Brace
Eaton’s B-Line Business seismic bracing components are designed to be compatible only with other B-Line bracing components,
resulting in a listed seismic bracing assembly. B-Line’s warranty for seismic bracing components will be the warranty provided in
B-Line’s standard terms and conditions of sale made available by B-Line, except that, in addition to the other exclusions from
B-Line’s warranty, Eaton’s B-line Business makes no warranty relating to B-Line’s seismic bracing components that are combined
with products not provided by Eaton’s B-Line Business.
All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.
Seismic Bracing Products
38
Seismic Structural Attachments
Fig. 825A - Bar Joist Sway Brace Attachment To Steel
Size Range: Fits up to 3/8” (9.5mm) thick structural steel member.
Accommodates all Fig. 900 Series sway brace attachments.
Material: Steel
Set Bolts & Hardware
Included
Function: To attach sway bracing to steel open web structural members.
3/8"
Features: This product’s design incorporates a concentric attachment
point which is critical to the performance of structural seismic connections.
NFPA 13 indicates the importance of concentric loading of connections
and fasteners. Permits secure non-friction connection without
drilling or welding. Unique design reinforces point of connection to joist.
Break off head bolt design assures verification of proper installation.
(9.5)
Approvals: Underwriters Laboratories Listed in the USA (UL) and
Canada (cUL). For additional load, spacing and placement information relating to
OSHPD projects, please refer to our Seismic Restraint Systems Guidelines.
Seismic Structural
Attachments
Installation Instructions: Fig. 825A is the structural attachment component of
a longitudinal or lateral sway brace assembly. It is intended to be combined with a
TOLCO transitional attachment, "bracing pipe" and a TOLCO "braced pipe"
attachment to form a complete bracing assembly.
NFPA 13 guidelines should be followed.
To Install: Place the Fig. 825A on the steel beam, tighten the cone point
set bolts until heads break off. Attach other TOLCO transitional attachment fitting,
Fig. 909, 910, 980, or 986. Transitional fitting attachment can pivot for adjustment to
proper brace angle.
Max. Horizontal Design Load (UL)
1600 lbs. (7.11kN)
with brace perpendicular to
bar joist / steel truss
Finish: Plain or Electro-Galvanized
Approx. Wt./100: 154.5 Lbs. (70.1kg)
Order By: Figure number and finish
Patent #6,098,942
Bar joist shown attached to
various roof materials
May pivot in any
direction
Max.
6” (152.4mm)
Shown with
Fig. 980
Eaton’s B-Line Business seismic bracing components are designed to be compatible only with other B-Line bracing components,
resulting in a listed seismic bracing assembly. B-Line’s warranty for seismic bracing components will be the warranty provided in
B-Line’s standard terms and conditions of sale made available by B-Line, except that, in addition to the other exclusions from
B-Line’s warranty, Eaton’s B-line Business makes no warranty relating to B-Line’s seismic bracing components that are combined
with products not provided by Eaton’s B-Line Business.
All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.
39
Seismic Bracing Products
Seismic Structural Attachments
Fig. 828 - Universal Sway Brace Attachment to Steel
Size Range: One size accommodates all Fig. 900 Series sway brace
attachments. Fits from 3/8” (9.4mm) to 7/8” (22.2mm) thick steel structure. For
thicknesses less than 3/8” (9.4mm) refer to Fig. 825 and Fif. 825A.
Component of State of
California OSHPD Approved
Seismic Restraints System
Material: Steel
Cone Point
Set Bolts A
Function: To attach sway bracing to various types of steel structural members.
Features: Permits secure non-friction connection without drilling or welding. Unique
design allows offset placement on wide flange beam, I-beam, C-channel, open web,
welded steel trusses, etc.. Secures brace to structure either across or along the
beam. Break-off set bolts allow for visual verification of proper installation torque.
Set Bolts
Included
Approvals: Underwriters Laboratories Listed in the USA (UL) and Canada (cUL).
Factory Mutual Approved (FM)
Cone Point
Set Bolt B
Seismic Structural
Attachments
Installation Instructions: The Fig. 828 is the structural attachment component
of a longitudinal or lateral sway brace assembly. It is intended to be combined with
a TOLCO transitional attachment, "bracing pipe" and a TOLCO "braced pipe"
attachment to form a complete bracing assembly.
NFPA 13, FM DS 2-8, and/or OSPHD guidelines should be followed.
To Install: Place the Fig. 828 on the flange of the beam, truss, or girder. Be sure the
attachment is fully engaged to the rear of the opening. Tighten the cone point
set bolts (A) until the heads break off. Tighten the cone point set bolt (B) until the
head breaks off. Remove the flange nut from set bolt (B). Install a TOLCO swivel
fitting Fig. 909, 910, 980, or 986. Use flange nut to secure the swivel fitting.
Finish: Plain or Electro-Galvanized
Approx. Weight/100: 275 Lbs. (124.7kg)
Order By: Figure number and finish
Patent #6,098,942, #8,534,625
Canada Patent #2,286,659
Patent Pending
Max. Horizontal Design Load (UL)
Max. Horizontal Design Load Across Beam
2015 lbs. (8.96kN)
Max. Horizontal Design Load Along Beam
2015 lbs. (8.96kN)
Max. Horizontal Design Load (FM)
With Brace Perpendicular To The Beam
Brace Angle (degrees from vertical)
30°-44°
45°-59°
60°-74°
75°-90°
1570
2220
1210
700
(6.98kN)
(9.87kN)
(5.38kN)
(3.11kN)
Beam, truss,
or girder
Beam, truss, or girder
Fig. 828
Max. Horizontal Design Load (FM)
With Brace Parallel To The Beam
Brace Angle (degrees from vertical)
30°-44°
45°-59°
60°-74°
Fig. 828
Shown with
Fig. 980
May pivot in any
direction
Shown with
Fig. 980
75°-90°
690
970
1210
1330
(3.07kN)
(4.31kN)
(5.38kN)
(5.91kN)
FM Approved design loads are based on ASD
design method.
Eaton’s B-Line Business seismic bracing components are designed to be compatible only with other B-Line bracing components,
resulting in a listed seismic bracing assembly. B-Line’s warranty for seismic bracing components will be the warranty provided in
B-Line’s standard terms and conditions of sale made available by B-Line, except that, in addition to the other exclusions from
B-Line’s warranty, Eaton’s B-line Business makes no warranty relating to B-Line’s seismic bracing components that are combined
with products not provided by Eaton’s B-Line Business.
All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.
Seismic Bracing Products
40
Seismic Structural Attachments
Fig. 906 - Sway Brace Multi-Fastener Adapter
Size Range: Use with 1” (25.4mm) and 11/4” (31.7mm) UL listed Fig. 900 Series
Earthquake Brace Attachment.
Material: Steel
Application: Allows sway brace fittings to develop greater
load carrying ability by providing multiple fastener
attachments. The National Fire Protection (NFPA) provides
information on fastener loads to various structures.
Refer to NFPA 13 (2010) 9.3.5.9.1.
Seismic Structural
Attachments
Approvals: Underwriters Laboratories Listed in the USA
(UL) and Canada (cUL) only when used with B-Line/TOLCO
Fig. 900 Series Earthquake Brace Attachments. Included in
our Seismic Restraints Catalog approved by the state of
California Office of Statewide Health Planning and
Development (OSHPD). For additional load, spacing and
placement information relating to OSHPD projects, please refer
to our Seismic Restraints System Guidelines 0300PA-10.
H1
B
H1
D
H2
C
Installation Instructions: Fig. 906 is a multiple fastener
structural attachment component of a longitudinal or lateral
sway brace assembly. It is intended to be combined with a
TOLCO transitional attachment, "bracing pipe" and a TOLCO
"braced pipe" attachment to form a complete bracing assembly.
NFPA 13 guidelines should be followed.
A
Mounting Hardware
Is Not Included
C
To Install: Attach the Fig. 906 to the structural surface as
per fastener design guidelines. Attach other TOLCO transitional
attachment fitting, Fig. 909, 910, 980, or 986. Transitional
fitting attachment can pivot for adjustment to proper brace
angle.
Finish: Plain or Electro-Galvanized. Contact B-Line for
alternative finishes and materials.
Order By: Figure number and specify dimensions H1 and H2.
Part
Number
906
A
in.
(mm)
12” (305.0)
B
C
D
in. (mm)
in. (mm)
in. (mm)
2” (50.8)
1/4” (6.3)
9” (228.6)
H1
H2
Approx. Wt./100
Lbs.
Specify
Specify
(kg)
307 (139.3)
Load Note: Actual design load determined by anchor and concrete strength, not to exceed the UL Listed maximum
horizontal load of 2015 lbs. (8.96kN).
Eaton’s B-Line Business seismic bracing components are designed to be compatible only with other B-Line bracing components,
resulting in a listed seismic bracing assembly. B-Line’s warranty for seismic bracing components will be the warranty provided in
B-Line’s standard terms and conditions of sale made available by B-Line, except that, in addition to the other exclusions from
B-Line’s warranty, Eaton’s B-line Business makes no warranty relating to B-Line’s seismic bracing components that are combined
with products not provided by Eaton’s B-Line Business.
All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.
41
Seismic Bracing Products
Seismic Structural Attachments
ACB Series - Concrete Screw Bolts
Features:
• For use in racking, shelving, material handling, structural anchorage,
masonry and food & beverage facilities.
• One piece heavy-duty anchor with a finished hex-head.
1/4”
Concrete Screw Bolts - Data
ACB Drill Bit Size (in. - mm)
Concrete Screw Tolerance Range (in. - mm)
Min. Embedment Depth (in. - mm)
Load Capacity Tension (lbs - kN) *
Load Capacity Shear (lbs - kN) *
3/8”
1/4”
- (6.3mm)
0.255” - 0.259” - (6.5mm - 6.6mm)
1” - (25.4mm)
335 lbs. - (1.49kN)
520 lbs. - (2.31kN)
3/8”
- (9.5mm)
0.385” - 0.389” - (9.8mm - 9.9mm)
11/2” - (38.1mm)
630 lbs. - (2.80kN)
1170 lbs. - (5.20kN)
* Based on concrete compression strength of 4000 psi in uncracked concrete using applied safety factor of
4.0. For additional loading information contact factory.
For ultimate strength design data in cracked and uncracked concrete, refer to ICC-ES ESR-2526 evaluation report.
Bolt Size
Concrete Bolt
Part No.
Diameter
in.
(mm)
Length
in.
Thread Length
(mm)
ACB-25-175
1/4”
(6.3)
13/4” (44.4)
ACB-25-225
1/4”
(6.3)
21/4” (57.1)
ACB-25-300
1/4”
(6.3)
ACB-37-175
3/8”
ACB-37-250
3/8”
ACB-37-300
3/8”
(9.5)
ACB-37-400
3/8”
Drill Bit
Part No.
(mm)
Lbs.
(kg)
15/8”
(41.3)
3.5
(1.6)
2”
(50.8)
4.2
(1.9)
(76.2)
23/4”
(69.8)
5.0
(2.3)
(9.5)
13/4” (44.4)
11/2”
(38.1)
7.8
(3.5)
(9.5)
21/2” (63.5)
21/4”
(57.1)
10.2
(4.6)
(76.2)
23/4”
(69.8)
11.6
(5.3)
4” (101.6)
33/4”
(95.2)
14.8
(6.7)
(9.5)
Type
3”
3”
Drill Diameter
in.
(mm)
Usable Length
in.
(mm)
Straight Shank
1/4”
(6.4)
13/4” (44.4)
1380
Straight Shank
1/4”
(6.4)
21/4” (57.1)
1314
SDS
1/4”
(6.4)
1316
SDS
3/8”
(9.5)
1372
Wt./100
in.
Overall Length
in.
(mm)
15/8”
(41.3)
2”
(50.8)
(76.2)
23/4” (69.8)
13/4” (44.4)
11/2” (38.1)
3”
All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.
Seismic Bracing Products
42
Seismic Structural
Attachments
• Fits standard fixture hole dimensions in fabricated steel.
• Fast installation and immediate loading reduces downtime.
• For proper performance, screw anchors must be installed with the
corresponding bits. The bits have a matched tolerance range designed
to provide optimum performance.
Seismic Structural Attachments
AWSD Series - Seismic Wedge Anchors
Component of State of
California OSHPD Approved
Seismic Restraints System
Features:
• Fully threaded, torque-controlled, wedge anchor which is
designed for consistent performance in cracked and
uncracked concrete.
• For use in concrete, structural sand lightweight concrete,
and concrete over metal deck.
• Nominal drill bit size is the same as the anchor diameter.
• ICC-ES listed, ESR-2502, Category 1
• Zinc plated carbon steel body with stainless steel expansion
clip from premium performance.
• Qualified for seismic and wind loading.
Seismic Structural
Attachments
3/8”-16
Seismic Wedge Anchor - Data
3/8”
ANSI Drill Bit Size (in. - mm)
1/2”-13
- (9.5mm)
1/2”
- (11.1mm)
9/16”
5/8”-11
- (12.7mm)
5/8”
- (14.3mm)
11/16”
- (15.9mm)
3/4”-10
3/4”
- (19.0mm)
Fixture Clearance Hole (in. - mm)
7/16”
Minimum Hole Depth (in. - mm)
25/8” - (66.7mm)
23/4” - (69.8mm)
41/4” - (107.9mm)
5” - (127.0mm)
4” - (101.6mm)
41/2” - (114.3mm)
53/4” - (146.0mm)
7” - (177.8mm)
Minimum Concrete Thickness (in. - mm)
Max. Tightening Torque (lbs-ft - N•m)
20 lbs-ft - (27.1N•m)
- (20.6mm)
40 lbs-ft - (54.2N•m) 60 lbs-ft - (81.3N•m) 110 lbs-ft - (149.1N•m)
23/8” - (60.3mm)
Min. Embedment Depth (in. - mm)
- (17.5mm)
13/16”
21/2” - (63.5mm)
37/8” - (98.4mm)
41/2” - (114.3mm)
For loading information, refer to the ICC-ES ESR-2502 evaluation report.
Wedge Anchor
Part No.
Anchor Size
Diameter
Length
in.
(mm)
in.
Thread Length
Wt./100
(mm)
in.
(mm)
Lbs.
(kg)
(76.2)
13/4”
(44.4)
11.4
(5.2)
AWSD-37-300
3/8”
(9.5)
3”
AWSD-37-350
3/8”
(9.5)
31/2”
(88.9)
21/4”
(57.1)
12.2
(5.5)
AWSD-37-375
3/8”
(9.5)
33/4” (95.2)
21/2”
(63.5)
13.2
(6.0)
AWSD-37-500
3/8”
(9.5)
5”
(127.0)
33/4”
(95.2)
16.0
(7.2)
AWSD-50-375
1/2”
(12.7)
33/4”
(95.2)
21/8”
(54.0)
23.0 (10.4)
AWSD-50-450
1/2”
(12.7)
41/2” (114.3)
27/8”
(73.0)
26.6 (12.0)
AWSD-50-550
1/2”
(12.7)
51/2” (139.7)
37/8”
(98.4)
34.0 (15.4)
AWSD-50-700
1/2”
(177.8)
53/8”
(136.5)
38.0 (17.2)
AWSD-62-475
5/8”
(15.9)
43/4” (120.6)
27/8”
(73.0)
50.3 (22.8)
AWSD-62-500
5/8”
(15.9)
5”
(127.0)
31/8”
(79.4)
52.0 (23.6)
AWSD-62-600
5/8”
(15.9)
6”
(152.4)
41/8” (104.8)
58.8 (26.7)
AWSD-62-700
5/8”
AWSD-75-550
3/4”
AWSD-75-625
3/4”
AWSD-75-700
3/4”
(12.7)
7”
(177.8)
51/8”
(130.2)
65.2 (29.6)
(19.0)
51/2” (139.7)
31/4”
(82.5)
81.5 (36.9)
(19.0)
61/4” (158.7)
4”
(101.6)
94.0 (42.6)
43/4”
(120.6)
106.5 (48.3)
(15.9)
(19.0)
7”
7”
(177.8)
All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.
43
Seismic Bracing Products
Seismic Structural Attachments
ATM Series - Self-Tapping Machine Screw Anchors
Features:
• For use in normal-weight concrete, structural sand
lightweight concrete and concrete over metal deck.
• Anchor design allows for shallow embedment and
mechanically interlocks with base material.
• Internally threaded anchor for easy adjustment and
removability of threaded rod or bolt.
• Fast anchor installation with a powered impact wrench.
• Suitable for overhead applications such as suspending
cable tray, strut, pipe hangers and conduit.
• FM Approved.
• ICC-ES listed, ESR-2272
• Made of Zinc Plated carbon steel.
• Setting tool included.
3
Self-Tapping Machine Screw Anchor - Data
/8”
ANSI Drill Bit Size (in. - mm)
1
Minimum Concrete Thickness (in. - mm)
4” - (101.6mm)
Max. Tightening Torque (lbs-ft - N•m)
/2” - (12.7mm)
8 lbs-ft - (10.8N•m)
Min. Embedment Depth (in. - mm)
15/8” - (41.3mm)
Load Capacity Tension (lbs - kN)
540 lbs - (2.40kN)
Load Capacity Shear (lbs - kN)
825 lbs - (3.67kN)
* Based on concrete compression strength of 4000 psi in uncracked concrete using applied safety factor of
4.0. For additional loading information contact factory.
For ultimate strength design data in cracked and uncracked concrete, refer to ICC-ES ESR-2526 evaluation report.
Anchor Thread Size
Part No.
ATM-37
Thread Length
in.
3
/8”-16
11
/16”
Wt./100
(mm)
lbs.
(kg)
(17.6)
5.2
(2.3)
All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.
Seismic Bracing Products
44
Seismic Structural
Attachments
Component of State of
California OSHPD Approved
Seismic Restraints System
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement