INSTALLATION
LICENSE TRIM PANEL With L.E.D. RUN/BRAKE ACCENT 3134
PARTS INCLUDED
1 License Plate Trim Panel with L.E.D. Run-Brake Accent Light
1
1 Hardware Kit Includes the Following Eight Items:
4 Black Neoprene Mounting Cap
4
2
6
6
#10–24 X 5/8” Button Socket Cap Screw
#10–24 X 3/8” Button Socket Cap Screw
#10 Flat Washer
#10 Internal Tooth Lock Washer
1
1
2
1
Six Plug Wire Harness
Black Nylon Male Connector Housing
Black Nylon Cable Tie, 4”
Dielectric Grease
Installation
Please read and understand entire instructions before starting installation.
THANK YOU FOR CHOOSING K
ϋ
RYAKYN!
IN ORDER TO PROTECT YOU AND OTHERS FROM POSSIBLE INJURY AND/OR
PROPERTY DAMAGE OR LOSS, PLEASE PAY CLOSE ATTENTION TO ALL
INSTRUCTIONS, WARNINGS, CAUTIONS AND ATTENTION NOTES REGARDING
THE USE AND CARE OF THIS PRODUCT.
CAUTION! This indication alerts you to the fact that ignoring the contents described herein can result in potential injury or material
damage.
ATTENTION!
This indication alerts you to the fact that ignoring the contents described herein may negatively affect product performance and
functionality.
TOOLS SUGGESTED
Set of Metric Hex Wrenches, Drill and Drill Bits
STRICTLY OBSERVE THE FOLLOWING GUIDELINES IN ORDER TO USE THE
PRODUCT PROPERLY AND AVOID POTENTIALLY DANGEROUS ACCIDENTS.
STEP 1
Read and understand all steps in the instructions before starting the installation. Park the motorcycle on a hard, level surface and turn off the
ignition.
STEP 2
STEP 3
-cont.-
Remove the license plate from the bracket on the rear center panel.
Remove the five bolts that hold on the center rear panel. Four of the bolts are located at the corners. On older models, there may be a fifth bolt located under the license plate. This center bolt is different than the other four and will not be reused. Remove the panel by pulling out on the bottom and slowly working off.
Remove the bracket from the rear panel.
PIC 1
REMOVE THESE BOLTS
3134-21GL-0411
CUSTOMER SERVICE
877.370.3604 (toll free)
INSTALLATION QUESTIONS [email protected] or call 715.247.2983
LIMITED WARRANTY
Küryakyn warrants that any Küryakyn products sold hereunder, shall be free of defects in materials and workmanship for a period of one
(1) year from the date of purchase by the consumer excepting the following provisions:
● Küryakyn shall have no obligation in the event the customer is unable to provide a receipt showing the date the customer purchased the product(s).
● The product must be properly installed, maintained and operated under normal conditions.
● Küryakyn makes no warranty, expressed or implied, with respect to any gold plated products.
● Küryakyn shall not be liable for any consequential and incidental damages, including labor and paint, resulting from failure of a
Küryakyn product, failure to deliver, delay in delivery, delivery in nonconforming condition, or for any breech of contract or duty between
Küryakyn and a customer.
● Küryakyn products are often intended for use in specific applications. Küryakyn makes no warranty if a Küryakyn product is used in applications other than intended.
● Küryakyn electrical products are warranted for one (1) year from the date of purchase by the consumer. L.E.D.’S contained in components of
Küryakyn products will be warranted for defects in materials and workmanship for 3 years from the date of purchase where as all other components shall be warranted for one(1) year.
This includes, but is not limited to; control modules, wiring, chrome & other components.
● Küryakyn makes no warranty of any kind in regard to other manufacturer¹s products distributed by Küryakyn. Küryakyn will pass on all warranties made by the manufacturer and where possible, will expedite the claim on behalf of the customer, but ultimately, responsibility for disposition of the warranty claim lies with the manufacturer.
ABOUT OUR CATALOG
For purchasing Küryakyn® products, you can receive a complete catalog free of charge.
Send the Proof-of-Purchase below with your address to: Küryakyn, P.O. Box 339,
Somerset, WI 54025.
Please indicate either Accessories Catalog for
Harley-Davidson® or GL & Metric Cruisers.
Be sure to ask your local dealer about other
Küryakyn® products, the motorcycle parts and accessories designed for riders by riders.
©2005 Küryakyn USA® All Rights reserved.
CAUTION! MEASURE TWICE – DRILL ONCE. Double check all reference marks made on the fender center panel BEFORE drilling.
Kuryakyn will not be responsible for incidental or consequential damages resulting from this installation.
STEP 4
Place the template on the panel paying attention to the up arrow. The two posts on the back of the template will set in the existing license plate holes to correctly align the template. Drill the four corner holes using a 1/4” bit, at the four outside locations. PIC 2 Remove the template.
STEP 5
Enlarge the hole, using a 3/8” bit, in the indent location shown in PIC 3.
STEP 6
Mount your license plate to the back of the trim using the bracket and proper fasteners. Install the 4 neoprene mounting caps to the threaded posts. PIC 4
STEP 7
Run the wire from the light through the 3/8” hole that you drilled in STEP 4. Place the trim piece in position and fasten into place using the 4, #10–24 X 5/8” screws
and
STEP 8
Locate the blue wire connectors that are behind the removed fender panel and install the supplied wire harness. PIC 5 The two small connectors shown in PIC 6 are where you will be plugging in the light.
NOTE:
If you have already installed additional Kuryakyn accessory lights on the rear of the bike and you do not have an extra plug in you may use Kuryakyn P/N 7302,
Multi-Plug and Play Connector, into the existing Kuryakyn wire adapter for additional plug-ins in place of the included wire adapter.
ATTENTION!
Küryakyn recommends the use of dielectric grease on electrical
connections.
STEP 9
You are now ready to reinstall the rear center panel. Hold the panel up close enough to the bike so you can plug in the wire connection. Get the panel into place and reinstall the four fasteners .
ATTENTION!
Secure all wiring away from any moving parts, pinch points or extreme heat. Küryakyn WILL NOT issue a warranty on any electrical component that fails due to pinched, crimped, broken, abraded, melted or frayed wires.
ATTENTION!
It is the installer’s responsibility to ensure that all of the fasteners
PIC 6
(including tightened before operation of the motorcycle. Küryakyn will not
issue lost due to improper installation.
Periodic maintenance may be required.
Ride On!
PIC 2
PIC 3
PIC 4
PIC 5
DRILL THESE FOUR HOLES
DRILL THIS LOCATION
BRACKET
PAGE
2
TEMPLATE IN PLACE
MOUNTING CAPS
WIRE ADAPTER INSTALLED
TRIM
INSTALLATION
