Epson PowerLite 400W User's Guide

PowerLite

®

400W

Multimedia Projector

User’s Guide

Important Safety Information

WARNING: Never look into the projector lens when the lamp is turned on; the bright light can damage your eyes.

Never let children look into the lens when it is on. Never open any cover on the projector, except the lamp and filter covers. Dangerous electrical voltages inside the projector can severely injure you. Except as specifically explained in this User’s Guide, do not attempt to service this product yourself. Refer all servicing to qualified service personnel.

WARNING: The projector and its accessories come packaged in plastic bags. Keep plastic bags away from small children to avoid any risk of suffocation.

Caution: When you replace the lamp, never touch the new lamp with your bare hands; the invisible residue left by the oil on your hands may shorten the lamp life. Use a cloth or glove to handle the new lamp.

Copyright Notice

All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko Epson Corporation. The information contained herein is designed only for use with this Epson product. Epson is not responsible for any use of this information as applied to other products.

Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.) failure to strictly comply with Seiko Epson Corporation’s operating and maintenance instructions.

Seiko Epson Corporation shall not be liable for any damages or problems arising from the use of any options or any consumable products other than those designated as Original Epson Products or Epson Approved Products by

Seiko Epson Corporation.

Trademarks

Epson and Instant Off are registered trademarks, and Epson Exceed Your Vision and Duet are trademarks of Seiko

Epson Corporation.

PowerLite and PrivateLine are registered trademarks; SizeWise is a trademark; and Epson Store and Extra Care are service marks of Epson America, Inc.

Pixelworks, DNX, and the DNX logo are trademarks of Pixelworks, Inc.

General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks.

The contents of this manual are subject to change without notice.

12/07 © 2007 Epson America, Inc.

2

C

Contents

Welcome

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Getting the Most from Your Projector . . . . . . . . . . . . . . . . . 8

Using Your Documentation . . . . . . . . . . . . . . . . . . . . . . . . . 9

Getting More Information . . . . . . . . . . . . . . . . . . . . . . . 9

Registration and Warranty . . . . . . . . . . . . . . . . . . . . . . . . . 10

Unpacking the Projector. . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Projector Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Additional Components . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Optional Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

1

Setting Up the Projector

. . . . . . . . . . . . . . . . . . . . 15

Positioning the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Whiteboard Installation . . . . . . . . . . . . . . . . . . . . . . . . 18

Other Installations . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Connecting to a Computer. . . . . . . . . . . . . . . . . . . . . . . . . 20

Connecting with the VGA Cable . . . . . . . . . . . . . . . . . 20

Connecting with a VGA-5BNC Cable. . . . . . . . . . . . . 22

Connecting an External Monitor . . . . . . . . . . . . . . . . . 23

Playing Sound Through the Projector . . . . . . . . . . . . . 24

Connecting External Speakers . . . . . . . . . . . . . . . . . . . 25

Connecting to Video Sources . . . . . . . . . . . . . . . . . . . . . . . 26

Connecting a Composite Video Source . . . . . . . . . . . . 27

Connecting an S-Video Source . . . . . . . . . . . . . . . . . . 28

Connecting an RGB Video Source. . . . . . . . . . . . . . . . 29

Connecting a Component Video Source . . . . . . . . . . . 30

Playing Sound Through the Projector . . . . . . . . . . . . . 31

3

4 Contents

2

Projecting

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Turning On Your Equipment . . . . . . . . . . . . . . . . . . . . . . . 36

Turning On the Projector . . . . . . . . . . . . . . . . . . . . . . . 36

Selecting the Image Source. . . . . . . . . . . . . . . . . . . . . . . 38

What To Do If You See a Blank Screen . . . . . . . . . . . . . 38

Adjusting the Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Focusing and Zooming Your Image . . . . . . . . . . . . . . . . 40

Adjusting the Height of Your Image . . . . . . . . . . . . . . . 41

Adjusting the Image Shape. . . . . . . . . . . . . . . . . . . . . . . 42

Adjusting the Brightness . . . . . . . . . . . . . . . . . . . . . . . . 42

Correcting Computer Images. . . . . . . . . . . . . . . . . . . . . 43

Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Shutting Down the Projector . . . . . . . . . . . . . . . . . . . . . . . . 44

3

Using the Remote Control

. . . . . . . . . . . . . . . . . . . 45

Controlling the Picture and Sound. . . . . . . . . . . . . . . . . . . . 46

Switching Between Picture Sources . . . . . . . . . . . . . . . . 46

Adjusting the Color Mode . . . . . . . . . . . . . . . . . . . . . . . 47

Turning Off the Picture and Sound . . . . . . . . . . . . . . . . 48

Stopping Action . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Zooming Your Image. . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Changing the Image’s Aspect Ratio . . . . . . . . . . . . . . . . 49

Replacing the Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

4

Fine-tuning the Projector

. . . . . . . . . . . . . . . . . . . . 53

Using the Projector’s Menu System . . . . . . . . . . . . . . . . . . . 54

Changing Menu Settings . . . . . . . . . . . . . . . . . . . . . . . . 55

Adjusting Colors and Clarity . . . . . . . . . . . . . . . . . . . . . . . . 56

Adjusting the Input Signal . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Customizing Projector Features . . . . . . . . . . . . . . . . . . . . . . 60

Selecting Projector Setup Options . . . . . . . . . . . . . . . . . . . . 62

Selecting Network Settings . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Viewing Lamp Usage and Other Information. . . . . . . . . . . . 64

Using the Projector’s Security Features. . . . . . . . . . . . . . . . . 66

Creating Your Own Screen Logo. . . . . . . . . . . . . . . . . . 67

Setting a Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Turning On the Password and User’s Logo . . . . . . . . . . 69

Starting the Projector with a Password. . . . . . . . . . . . . . 70

Disabling the Projector’s Buttons . . . . . . . . . . . . . . . . . 71

Installing Security Locks . . . . . . . . . . . . . . . . . . . . . . . . 71

Restoring the Default Settings . . . . . . . . . . . . . . . . . . . . . . . 72

5

Maintenance and Transportation

. . . . . . . . . . 73

Cleaning the Lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Cleaning the Projector Case . . . . . . . . . . . . . . . . . . . . . . . . . 74

Cleaning and Replacing the Air Filter . . . . . . . . . . . . . . . . . 74

Replacing the Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Resetting the Lamp Timer . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Transporting the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . 80

6

Solving Problems

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

Using On-Screen Help. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

What To Do When the Lights Flash . . . . . . . . . . . . . . . . . . 82

Solving Problems with the Image or Sound . . . . . . . . . . . . . 84

Solving Password Problems . . . . . . . . . . . . . . . . . . . . . . . . . 89

Solving Problems with the Remote Control . . . . . . . . . . . . . 90

Solving Network Problems. . . . . . . . . . . . . . . . . . . . . . . . . . 91

Where To Get Help. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

Speak to a Support Representative. . . . . . . . . . . . . . . . . 92

7

Monitoring the Projector Over a Network

. . 93

Installing the Network Software. . . . . . . . . . . . . . . . . . . . . . 94

Windows System Requirements . . . . . . . . . . . . . . . . . . 94

Installing the Software on a Windows System . . . . . . . . 94

Connecting to the Network . . . . . . . . . . . . . . . . . . . . . . . . . 95

Selecting Network Settings. . . . . . . . . . . . . . . . . . . . . . . . . . 96

Using Projector E-mail Alerts . . . . . . . . . . . . . . . . . . . . 97

Contents 5

6 Contents

Using EMP Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98

Opening and Closing EMP Monitor . . . . . . . . . . . . . . . 98

Registering a Projector . . . . . . . . . . . . . . . . . . . . . . . . . . 99

Monitoring Your Projector . . . . . . . . . . . . . . . . . . . . . . 99

Using E-mail Alerts . . . . . . . . . . . . . . . . . . . . . . . . . . . 102

Using a Browser to Monitor the Projector . . . . . . . . . . . . . 103

A

Technical Specifications

. . . . . . . . . . . . . . . . . . . . 105

General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105

Projection Lamp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106

Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106

Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106

Environmental . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107

Safety and Approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107

Compatible Video Formats . . . . . . . . . . . . . . . . . . . . . . . . 108

Compatible Computer Display Formats. . . . . . . . . . . . . . . 109

B

Notices

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111

Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . 111

FCC Compliance Statement. . . . . . . . . . . . . . . . . . . . . . . . 113

Index

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115

W -

Welcome

T he PowerLite ® 400W is a portable, short-throw projector that weighs less than 8 pounds (3.6 kg) and offers 1800 ANSI lumens of brightness. From classrooms to boardrooms, your full-color presentations and videos will be bright and vibrant even in ordinary indoor lighting.

Images are displayed at a native resolution of 1280 × 800 pixels

(WXGA) in a wide-screen 16:10 aspect ratio. Epson ® 3LCD technology ensures accurate color and remarkable saturation, even in well-lit rooms.

The projector’s ground-breaking short-throw lens is ideal for wall mounting, allowing more space for your class or audience with no shadow cast by the presenter. It can be placed as close as 21 inches

(54 cm) from a screen, an interactive whiteboard (IWB), or another projection surface. And its powerful 10 W speaker and crisp 500:1 contrast ratio ensure your presentations are seen and heard at their best.

You can connect the projector to a wide range of computers, including

IBM ® -compatible PCs and laptops, Apple ® PowerPC ® and Intel ®

Core ™ Macintosh ® computers, PowerBook ® computers, and many iMac ® and iBook ® series systems. With Epson’s patented SizeWise ™ technology, the projector supports computer displays ranging from

VGA through WSXGA+. You can also connect the projector to a

LAN (local area network) so you can monitor the projector from a remote network computer using the included EMP Monitor software

(Windows ® only).

You can use any of the following video sources: HDTV, VCR, DVD player, gaming console (such as Microsoft ® Xbox, ™ Sony ®

PlayStation ® 3, and Nintendo Wii ™ ), camcorder, or digital camera.

The projector supports NTSC, PAL, and SECAM video formats.

7

8 Welcome

You can connect up to four devices to the projector at the same time.

With the projector’s Source Search button, you don’t even have to identify your input source. Just press the button until you see the image you want on the screen.

To prevent unauthorized use of the projector, you can assign a password, create a user logo which is displayed at startup to identify the projector, and disable the projector’s buttons through a full or partial Control Panel Lock feature. For more information about

security features, see page 66.

■

■

■

■

Getting the Most from Your Projector

Depending on your presentation, you can take advantage of any or all of these options:

Connecting to a laptop or other computer

If you want to connect the projector to a laptop or desktop

computer, see page 20. For additional presentation control, you

can connect an external monitor to view the presentation on your computer simultaneously.

Connecting to video sources

You can connect a DVD player, VCR, HDTV, camcorder, digital

camera, and other video sources to your projector. See page 26 for

instructions.

Using the remote control

The remote control lets you switch from computer to video sources, zoom in on part of your image, freeze or mute the presentation, and adjust many other projector features. For

details, see Chapter 3.

Enhancing sound in your presentation

By connecting your projector to external speakers, you can enhance the audio impact of your presentations. (The internal

10 W speaker provides powerful sound, but is disabled when you

connect external speakers.) See page 25 for details.

Using Your Documentation

In addition to this manual, your documentation includes a Quick

Setup sheet, warranty brochures, and an Epson PrivateLine ® Support card.

The Quick Setup sheet gives instructions to quickly set up your projector and connect it to a computer or video device.

■

■

This book contains all the information you need to set up and use your projector. Please follow these guidelines as you read through it:

■ Warnings must be followed carefully to avoid bodily injury.

Cautions must be observed to avoid damage to your equipment.

Notes contain important information about your projector.

Getting More Information

Need tips on giving presentations? How about quick steps for setting up your projector? Here’s where you can look for help:

■

■ www.presentersonline.com

Includes a library of articles covering presentation tips, tricks, and technology. The site provides templates, clip art, and sound clips, as well as Presenters Services to use on the road. Even more resources and services are available if you register to join the

Presenters Club—and it’s free.

Built-in help system

Press the Help button on the remote control or projector to get

quick solutions for common problems. See page 82 for details.

■ epson.com/support

Download FAQs (frequently asked questions) and e-mail your questions to Epson support.

If you still need help after checking this User’s Guide and the sources listed above, you can use the Epson PrivateLine Support service to get help fast. Call (800) 637-7661 and enter the PIN on your PrivateLine

Support card. See page 91 for more information.

Welcome 9

10 Welcome

Registration and Warranty

Your projector comes with a basic carry-in warranty. For details, see the warranty brochure that came with your projector.

In addition, Epson offers Extra Care SM Road Service at no additional charge. In the unlikely event of an equipment failure, you won’t have to wait for your unit to be repaired. Instead, Epson will ship you a replacement unit anywhere in the United States or Canada, usually within one business day. See the Extra Care Road Service brochure for details.

To register, complete the registration form that came with your projector and mail it to Epson. Or register your product online using your projector CD, or at: http://www.epson.com/webreg

Registering also lets you receive special updates on new accessories, products, and services.

Unpacking the Projector

After unpacking the projector, make sure you have all these items:

Projector and lens cover

Remote control and batteries

VGA computer cable

Power cord Projector

CD-ROMs

Password Protected sticker

Save the protective pad attached to the lens cover and all other packaging in case you need to ship the projector. Always use the original packaging (or equivalent) when you send the projector to

another location. See page 80 for transportation instructions.

Projector Parts

Front

Control panel

Lamp cover

Security slot

Focus ring

Air filter

Lens

Lens cover

Air exhaust vents

Remote control sensor Front adjustable foot Foot release lever

Back

LAN port

S-Video port

Video port

Audio L-R input ports

Computer 1 and 2

(VGA/Component Video) ports

Audio 1 and 2 input ports

Remote control sensor

Speaker

Bottom

Mounting bracket hole

Audio Out port

Monitor Out port

(for Computer1 port output only)

Power inlet

RS-232C serial port

Rear adjustable foot

Mounting bracket holes

Rear adjustable feet

Security lock slot

Mounting bracket hole

Welcome 11

12 Welcome

Control Panel

Turns projector on and off

Opens menu system

Up/down arrows and keystone correction

Cancel/exit

Opens help system

Indicate projector status

Searches for source image

Left/right arrows and

Wide/Tele buttons

Automatically adjusts computer images

■

■

■

■

Additional Components

Depending on how you plan to use the projector, you may need additional components:

To receive an S-Video signal, you need an S-Video cable. One is usually provided with your video device or you can purchase it

from Epson. See page 13.

To receive a component video signal from a VCR or other video device, you need a D-sub, 15-pin, component-to-VGA video

cable, which is available for purchase from Epson. See page 13.

Some older PowerBooks and Macintosh desktop models may need a Macintosh video adapter; see your computer dealer. Older iMac systems may need a special VGA adapter, and newer iMac,

MacBook, and PowerBook systems may need a mini

DVI-to-VGA adapter; see your computer dealer.

To receive an audio signal, you need a commercially available audio cable; see your computer or electronics dealer.

Optional Accessories

To enhance your use of the projector, Epson provides the following optional accessories:

Product

Replacement lamp

Air filter set (includes 2 filters)

Replacement remote control

Presentation remote control

Component-to-VGA video cable

S-Video cable

Distribution amplifier

Short-throw Projector Wall Mount

Projector Wall Mount Security Module

Interactive Whiteboard Retrofit Installation Module

50-inch portable screen (4:3 aspect ratio)

60-inch portable pop-up screen (4:3 aspect ratio)

80-inch portable pop-up screen (4:3 aspect ratio)

83.6-inch hanging pull-down screen

(4:3 aspect ratio)

Duet ™ Ultra Portable Projector screen

(4:3 and 16:9 aspect ratio)

ELPDC05 high resolution document imager

Kensington ® security lock

Ceiling mount (gyro lock with suspension adapter)

False ceiling plate

Suspension adapter

Security bracket/cabling for gyro lock mounts

Adjustable ceiling channel

V12H162020

ELPSL01

ELPMBUNI

ELPMBFCP

ELPMBAPL

ELPMBSEC

ELPMBACC

Product number

V13H010L42

V13H134A13

1456641

V12H007T0B

ELPKC19

ELPSV01

ELPDA01

ELPMSTPW

ELPMSECM

ELPMIWBM

ELPSC06

ELPSC07

ELPSC08

ELPSC09

ELPSC80

You can purchase screens, carrying cases, or other accessories from an

Epson authorized reseller. To find the nearest reseller, call

800-GO-EPSON (800-463-7766). Or you can purchase online at

www.epsonstore.com (U.S. sales) or www.epson.ca (Canadian sales).

note

To purchase a replacement remote control, call

(562) 276-4394 (U.S.) or

(905) 709-3839 (for dealer referral in Canada).

Welcome 13

14 Welcome

1

Setting Up the Projector

T his chapter tells you how to set up the projector and connect it to a computer or video source. You can connect up to four devices

1 simultaneously: four video sources, or two computer and two video sources.

You’ll find instructions for the following in this chapter:

■ Positioning the projector

■

■

Connecting to a computer

Connecting to video sources

15

note

You can download the

Projection Distance

Calculator program from the Drivers & Downloads section of Epson’s website: www.epson.com/support

Positioning the Projector

Before connecting the projector, you need to decide where to place it.

If the projector isn’t already installed in the room you’re using, you can place it on a table in front of the screen. This lets you stand in the front of the room, face the audience, and control the projector.

Ideally, you should place the projector between 26 to 48 inches (66 to

122 cm) from the screen. Use the illustrations and tables below to help you determine approximately how far to place it based on the screen size you’re using and the aspect ratio of the image. Image size can vary depending on how you adjust the zoom and other settings.

Center of lens

Center of lens

16 Setting Up the Projector

16:10 aspect ratio

Screen size

50 inches

(127 cm)

60 inches

(152 cm)

70 inches

(178 cm)

80 inches

(203 cm)

90 inches

(229 cm)

100 inches

(254 cm)

110 inches

(279 cm)

Projection distance (A)

Wide to Tele

21 to 29 inches

(54 to 73 cm)

26 to 35 inches

(65 to 89 cm)

30 to 41 inches

(76 to 104 cm)

34 to 47 inches

(88 to 119 cm)

39 inches

(99 cm)

43 inches

(110 cm)

48 inches

(122 cm)

Offset (B)

Wide to Tele

4 to 10 inches

(10 to 25 cm)

4.8 to 12 inches

(12 to 30 cm)

5.6 to 14 inches

(14 to 36 cm)

6.4 to 16 inches

(16 to 41 cm)

7.2 inches

(18 cm)

7.9 inches

(20 cm)

8.7 inches

(22 cm)

Screen size

49 inches

(124 cm)

60 inches

(152 cm)

70 inches

(178 cm)

80 inches

(203 cm)

90 inches

(229 cm)

100 inches

(254 cm)

107 inches

(272 cm)

4:3 Aspect Ratio

Screen size

(diagonal)

44 inches

(112 cm)

50 inches

(127 cm)

60 inches

(152 cm)

70 inches

(178 cm)

80 inches

(203 cm)

90 inches

(229 cm)

97 inches

(246 cm)


Wide to Tele

21 to 29 inches

(54 to 73 cm)

24 to 33 inches

(61 to 83 cm)

29 to 40 inches

(73 to 100 cm)

34 to 46 inches

(86 to 118 cm)

39 inches

(99 cm)

44 inches

(112 cm)

48 inches

(122 cm)

16:9 Aspect Ratio

Offset (B)

Wide to Tele

4 to 13.1 inches

(10 to 33 cm)

4.5 to 14.7 inches

(11 to 37 cm)

5.4 to 17.6 inches

(14 to 45 cm)

6.3 to 20.6 inches

(16 to 52 cm)

7.2 inches

(18 cm)

8.1 inches

(21 cm)

8.7 inches

(22 cm)


Wide to Tele

21 to 29 inches

(54 to 73 cm)

26 to 36 inches

(67 to 91 cm)

31 to 42 inches

(78 to 107 cm)

35 inches

(90 cm)

40 inches

(102 cm)

45 inches

(113 cm)

48 inches

(122 cm)

Offset (B)

Wide to Tele

5.3 to 12 inches

(13 to 30 cm)

6.5 to 14.7 inches

(17 to 38 cm)

7.6 to 17.2 inches

(19 to 44 cm)

8.7 inches

(22 cm)

9.8 inches

(25 cm)

10.9 inches

(28 cm)

11.7 inches

(30 cm)

Setting Up the Projector 17


Also keep these considerations in mind:

■ If you’re projecting from a table or other flat surface, make sure the surface is sturdy and level.

■

■

Make sure there is plenty of space for ventilation around and under the projector. Do not set the projector next to loose papers that could block the vents on the sides of the projector.

Make sure the projector is within 6 feet (2 m) of a grounded electrical outlet or extension cord.

■ Place the projector in front of the center of the screen, facing it squarely. If the projector isn’t positioned this way, the image will be “keystone” shaped ( or ) instead of rectangular.

If you’re projecting from a table or other flat surface, you may need to tilt the projector up by extending the front adjustable foot, as

described on page 41. This causes the image to lose its rectangular

shape. You can adjust the shape using the buttons on the projector

(see page 42), or using the projector’s menu system (see page 53).

Whiteboard Installation

You can project onto a whiteboard (or IWB, interactive whiteboard) by mounting the projector to the wall or directly onto a compatibly equipped whiteboard.

To mount the projector on the wall or attach it to a whiteboard, you’ll

need an optional short-throw wall mounting system. (See page 13 for

ordering information.) You’ll also need to select Front/Ceiling for the

Projection option in the Extended menu. See page 62 for details.

Other Installations

You can also project from behind the screen or from the ceiling, with the projector mounted upside-down:

Rear projection (using a translucent screen)

Front/ceiling projection Rear/ceiling projection (using a translucent screen)

To project from the ceiling, you’ll need the optional ceiling mount.

(See page 13 for ordering information.) You’ll also need to select

Front/Ceiling or Rear/Ceiling for the Projection option in the

Extended menu. To project from the rear, select Rear

. See page 62 for

details.


note

If you have an iBook with an RCA video-out port, follow the instructions for connecting to a video device

on page 27.

Connecting to a Computer

You can connect the projector to any computer that has a standard

VGA or BNC monitor port, including PC notebook and laptop computers, Macintosh PowerBooks and iBooks, and hand-held devices.

Follow the instructions in this section to:

■ Connect the projector to your computer with the VGA cable included with the projector.

■ Connect the projector to your computer with a commercially available VGA–5BNC cable.

After connecting the projector to your computer, you may also want to:

■

■

Connect a monitor to the projector so you can view your presentation close-up as well as on-screen (not necessary if you’re

using a laptop); see page 23.

Connect the projector to your computer with a commercially

available audio cable to play computer audio; see page 24.

Connecting with the VGA Cable

Follow these instructions to connect to your computer with the VGA cable that came with your projector. Before you start, make sure your computer and the projector are turned off.

1. If you are connecting the projector to a desktop computer, disconnect the monitor cable from your computer.

2. Locate the VGA computer cable that came with the projector.

VGA computer cable


Connect one end of the cable to the projector’s Computer1 or

Computer2 port.

Computer1 and Computer2 ports

3. Connect the other end of the cable to your computer’s video-out or monitor port.

If you’re using a PowerBook or iBook and you can’t connect the cable, you may need to use an optional Macintosh video adapter; see your computer dealer.

4. If you connected the computer to the Computer1 port and you want to view the display simultaneously on your computer

monitor and the projector screen, see “Connecting an External

Monitor” on page 23.

5. To play audio from your computer through the projector speaker,

see “Playing Sound Through the Projector” on page 24.

6. Tighten the screws on the connectors.

If you don’t need to make any other connections, you can plug in

your projector and turn it on. See page 36 for instructions.

If more than one device is connected to the projector, select the correct source after projection starts by pressing the Source Search

button on the projector or remote control. See page 38.


VGA-5BNC cable

Connecting with a VGA-5BNC Cable

If your computer provides video output through BNC connectors, follow these instructions to connect the projector to your computer with an optional VGA-5BNC cable. Before you start, make sure your computer and the projector are turned off.

1. Disconnect the monitor cable from your computer.

2. Connect the cable’s VGA connector to the projector’s

Computer1 or Computer2 port.



3. Connect the BNC connectors to your computer’s BNC ports.

4. If you want to view the display simultaneously on your computer

monitor and the projector screen, see “Connecting an External

Monitor” on page 23.

5. To play audio from your computer through the projector speaker,

see “Playing Sound Through the Projector” on page 24.

6. Tighten the screws on the VGA connector.





Connecting an External Monitor

If you want to see your presentation close-up as well as on the projection screen, you can connect an external monitor to the projector. This lets you view images on your computer monitor while the projector is in standby mode (plugged in but not turned on) and check your presentation or switch between picture sources even if you’ve pressed the A/V Mute button on the remote control to turn off projection on the screen. (Simultaneous display is possible only when the computer is connected to the projector’s Computer1 port.)

Make sure the projector and computer are off. Then connect the monitor’s cable to the projector’s Monitor Out port, as shown: note

Some LCD monitors may not be able to display the image correctly. If you have trouble displaying the image, connect a multiscan monitor. If you’re projecting computer images, make sure the computer’s refresh rate is set to 60 Hz or greater. See your computer and/or monitor documentation for instructions.




3.5 mm stereo mini-jack audio cable

Playing Sound Through the Projector

You can connect a commercially available 3.5 mm stereo mini-jack audio cable to take advantage of the projector’s built-in speaker. You can obtain the audio cable from a computer or electronics dealer.

1. Connect one end of the 3.5 mm stereo mini-jack audio cable to the corresponding Audio1 or Audio2 jack on the projector.

Audio1 and

Audio2 jacks

2. Connect the other end of the audio cable to your laptop’s headphone jack or audio-out jack, or your desktop’s speaker or audio-out port.




Connecting External Speakers

You can output sound to external speakers with built-in amplifiers.

When you play sound through external speakers, the projector’s built-in speaker is disabled.

1. Locate the appropriate cable to connect your speakers.

Depending on your speakers, you may be able to use a commercially available audio cable with a stereo mini-jack connector on one end and pin jacks on the other end. For some speakers, you may have to purchase a special cable or use an adapter.

2. Connect the stereo mini-jack end of the audio cable to the Audio

Out port on the projector.

3. Connect the other end of the cable to your speakers.


note

The projector does not support TV antenna cable

F connectors.

■

■

Connecting to Video Sources

You can connect a DVD player, VCR, camcorder, digital camera, gaming console, or any other compatible video source to your projector. You can connect up to four video devices at one time.

The projector supports HDTV, SDTV, NTSC, PAL, and SECAM, and automatically detects the video format. It can receive composite video, S-Video, RGB video, and component video. The type of cable you need depends on the video source:

For composite video, use a commercially available RCA A/V

cable. See page 27.

For S-Video, use the S-Video cable supplied with your video

device or order one from Epson. See page 28.

■

■

For RGB video, use the VGA computer cable included with the

projector. See page 29.

For component video, you’ll need the optional Epson

component-to-VGA video cable. See page 30.

After connecting your video device to the projector, you may want to connect an audio cable to play sound from your video equipment through the projector’s built-in speaker or external speakers. See

page 31 for instructions.


Connecting a Composite Video Source

If you’re connecting a composite video device, use a commercially available RCA A/V cable. Before starting, make sure the projector and your DVD player or other video source are turned off.

1. Connect the yellow RCA plug on one end of the cable to the projector’s yellow Video port.

Video port

2. Connect the yellow plug on the other end of the cable to the video-out port on your video source.

3. To play sound through the projector, follow the instructions

beginning on page 31.






Connecting an S-Video Source

If your video source has an S-Video jack, you can use it to project a higher quality video image. You’ll need an S-Video cable, which is usually provided with your video source, or you can purchase one

from Epson (part number ELPSV01). See page 13 for ordering

information.

Before starting, make sure the projector and your DVD player or other video source are turned off.

1. Insert one end of the S-Video cable into the projector’s S-Video port and the other end into the S-Video output port of your video source.

S-Video port








Connecting an RGB Video Source

Follow these instructions to connect the projector to a video player or satellite receiver that has an RGB video output port using the VGA computer cable that came with the projector.

Before starting, make sure the projector and your DVD player or other video source are turned off.

1. Connect one end of the VGA computer cable to the Computer1 or Computer2 port on the projector.


2. Connect the other end to the video port on your player.





If more than one device is connected to the projector, select

Computer 1 or Computer 2 as the source after projection starts by pressing the Source Search button on the projector or remote

control. See page 38.


Component-to-VGA video cable

Connecting a Component Video Source

If your video source has component video connectors, you can use them to project a higher quality video image. You’ll need a component-to-VGA video cable, which can be purchased from Epson

(part number ELPKC19). See page 13 for ordering information.

Before starting, make sure the projector and your DVD player or other video device are turned off.

1. Connect the 15-pin VGA connector end of the component-to-VGA video cable to the projector’s Computer1 or

Computer2 port.



2. Insert the three component ends of the component-to-VGA video cable into the color-coded video output ports on your video source, usually labelled Y , Pb , Pr or Y , Cb , Cr .





If more than one device is connected to your projector, select

Computer1 or Computer2 as the source by pressing the Source

Search

button on the projector or the remote control. See page 38.

Playing Sound Through the Projector

The projector has a built-in speaker with a maximum output of 10 W.

You can play sound from your video equipment through the projector’s speaker if your video device has an audio output port.

For RCA-Type Audio Output Ports

Most video devices have an RCA-type audio output port. In this case, use a commercially available RCA-type audio cable to connect the projector to your video source:

1. Connect one end of the RCA audio cable to the L-Audio-R jacks on the projector.

L-Audio-R jacks (for Video and S-Video ports)

2. Connect the red and white plugs on the other end of the RCA audio cable to the corresponding color-coded audio output port on your video source.





For Stereo Mini-Jack Audio Output Ports

Some video devices, especially camcorders, may have a stereo mini-jack audio output port. To connect to the L-Audio-R input jacks when using the S-Video or Video port, use a commercially available stereo mini-jack audio adapter cable (3.5-mm stereo miniplug to two male RCA plugs) to connect to the projector.

1. Connect one end of the audio adapter cable to the L-Audio-R jacks on the projector.

L-Audio-R jacks

2. Connect the other end of the audio adapter cable to your video device’s audio output port.



Connecting External Speakers

You can output sound to external speakers with built-in amplifiers.

When you play sound through external speakers, the projector’s built-in speaker is disabled.

1. First connect your video and audio input cables as necessary.

2. Locate the appropriate cable to connect your external speakers.

Depending on your speakers, you may be able to use a commercially available audio cable with a stereo mini-jack connector on one end and pin jacks on the other end. For some speakers, you may have to purchase a special cable or use an adapter.

3. Connect the stereo mini-jack end of the audio cable to the

Audio Out port on the projector.

4. Connect the other end of the cable to your speakers.

The projector’s internal speaker is disabled while sound is output to external speakers, but you can use the remote control to adjust the volume.



2

Projecting

O nce you’ve set up the projector, you’re ready to turn it on, adjust the image, and give your presentation.

2

Although you can operate the projector without it, the remote control

lets you use additional features. See Chapter 3 for instructions on

using the remote.

This chapter covers the following:

■ Turning on the projector and other equipment

■

■

■

Adjusting the image

Adjusting the volume

Shutting down the projector

35

36 Projecting

Turning On Your Equipment

Make sure your projector and other equipment are set up and

connected correctly, as described in Chapter 1. Then turn on your

projector, as described below.

If you turn on your connected computer or video equipment before starting the projector, the projector automatically detects and displays the image source. If you turn on the projector first, or have multiple pieces of connected equipment, you may have to select the image

source manually. See page 38.

Turning On the Projector

Follow these steps to plug in and turn on the projector:

1. Remove the lens cover.

2. Connect one end of the power cord to the projector’s power inlet, then connect the other end to an electrical outlet. The P Power light on top of the projector turns orange, indicating that the projector is receiving power but is not yet turned on.

3. Turn on your computer or video source if you have not already.

4. Press the P Power button on the projector or on the remote control to turn it on. note

If you are using the remote control for the first time, be sure to insert the batteries as

described on the Quick

Setup poster.

Power button

The projector beeps and the P Power light flashes green as the projector warms up. The projector lamp comes on in about

5 seconds and the P Power light stays green.

■ If you’re using a computer, you should see your computer display projected after a moment or two. If not, you need to

select the image source. See page 38.

■

(With Windows, if you see a message saying that it has found a plug-and-play monitor, click Cancel .)

If you’re projecting a video, you may need to press the

Source Search button on the projector or remote control to switch to your video source. Then press the Play button on your DVD player or other device.

■

If you are prompted to enter a password, see page 70.

To focus and adjust the image, see page 40. If a projected image fails

to appear, see “What To Do If You See a Blank Screen” on page 38.

When you’re done, shut down the projector as described on page 44.

warning

Never look into the lens when the lamp is on. This can damage your eyes, and is especially dangerous for children.

Projecting 37

note

The name of the selected image source appears briefly in the upper right corner of the screen.

Selecting the Image Source

Selecting the image source lets you switch between images input from different pieces of equipment connected to the projector (such as a computer and DVD player). If you don’t see the image you want, press the Source Search button on the remote control or projector until the correct device image is projected. If a projected image fails to appear, see the next section for help.

Once you see your image, turn to page 40 for instructions on focusing

and making other image adjustments.

What To Do If You See a Blank Screen

If you see a blank screen or a blue screen with the message No Signal after turning on your computer or video source, try the following:

■

■

■

■

Make sure the cables are connected correctly, as described in

Chapter 1.

Make sure the P Power light is green and not flashing and the lens cover is removed.

Make sure you’ve selected the correct image source; see the previous section. Allow a few seconds for the projector to sync up after pressing the button.

Check the Signal menu to make sure the correct input source is

selected. See page 58.

If you’re using a PC laptop:

■ Hold down the Fn key and press the function key that lets you display on an external monitor. It may have an icon such as or it may be labelled CRT/LCD . Allow a few seconds for the projector to sync up after pressing it. Check your laptop’s manual or online help for details.

On most systems, the or CRT/LCD key lets you toggle between the LCD screen and the projector, or display on both at the same time.

38 Projecting

■ If you’re projecting from a laptop, and you don’t see the same image on the projection screen and computer screen, check your monitor settings to make sure both the LCD screen and the external monitor port are enabled.

From the Control Panel, open the Display utility. Click the

Settings tab, then click Advanced . The method for adjusting the settings varies by brand; you may need to click a Monitor tab, then make sure the external Monitor port is set as your primary display and/or enabled. See your computer’s documentation or online help for details.

If you’re using a Macintosh laptop with OS X:

You may need to set up your system to display on the projector screen as well as the LCD screen. Follow these steps:

1. From the Apple menu, select System Preferences , then click

Display or Displays.

2. Select VGA Display or Color LCD , click Arrange or

Arrangement , and make sure Mirror Displays is checked.

Click here

Select Mirror

Displays

Projecting 39

40 Projecting

■

Adjusting the Image

Once you see your image, you’ll need to make certain adjustments:

To focus or zoom your image, see below.

■

■

If the image is too high or too low, you can reposition it.

See page 41.

If the image isn’t square, see page 42.

■

■

To adjust image brightness, see page 42.

If a computer image displays incorrectly, see page 43.

You can make many other adjustments to the image—such as changing the brightness, contrast, and aspect ratio—using the

projector’s menu system. See Chapter 4 for more information.

Focusing and Zooming Your Image

Rotate the focus ring to sharpen the image.

Focus ring

Press the Wide button on the projector to enlarge the image, or the

Tele button to reduce it.

Wide button

Tele button

You can also change the image size by moving the projector closer to or farther away from the screen. You can use the E-Zoom buttons on

the remote control to zoom in on a portion of the image. See page 49

for instructions.

Adjusting the Height of Your Image

If you’re projecting from a table or other flat surface and the image is too high or low, you can correct it by adjusting the projector’s front and/or rear feet.

1. To adjust the front foot, stand behind the projector. Press up on the blue foot release lever and lift the front of the projector to extend the front adjustable foot.

2. Once the image is positioned where you want, release the lever to lock the foot in position.

3. To adjust the rear feet, rotate the feet to extend or retract them to the desired height.

If the projected image isn’t rectangular, follow the instructions in the next section.

Projecting 41

42 Projecting

Adjusting the Image Shape

If the projector is tilted up or down, the images that are displayed will be distorted. To correct the distortion or “keystone” shape, do one or more of the following:

■

■

If your image looks like or , you’ve placed the projector off to one side of the screen, at an angle. Move it directly in front of the center of the screen, facing the screen squarely.

If your image looks like or , you need to adjust the keystone correction value. Press the or buttons on the projector to correct the shape of the image. After correction, your image will be slightly smaller.

Keystone correction buttons

You can also make keystone adjustments using the projector’s Settings

menu. See page 60.

Adjusting the Brightness

The brightness of an image depends on the source you are projecting and the amount of light in the room. If the image is too bright or not bright enough, here are two ways you can adjust it:

■

■

Change the Brightness

setting in the Image menu. See page 57.

Select Low or High for the Brightness Control option in the

Settings menu. (See page 61.) Low brightness mode extends the

life of the lamp and decreases the fan noise.

Correcting Computer Images

If you’ve connected a computer and the image doesn’t look right, or it doesn’t fit properly on the screen, press the Enter button on the projector or the Enter/Auto button on the remote control. This automatically resets the projector’s tracking, sync, resolution, and position settings. You must be projecting a computer image for this button to have any effect. Additionally, if the Auto Setup option in the Signal menu is set to Off , the Auto function will not work. See

page 59.

Adjusting the Volume

You can use the Vol– and Vol+ buttons on the remote control to increase or decrease the volume for the projector’s built-in speaker.

A volume gauge appears on the screen while the volume is being adjusted.

note

You can also adjust the volume using the projector’s

Settings menu. See page 60

for details.

You must adjust the volume separately for each input source.

Volume control buttons

Projecting 43

note

When the projector has not received any input signals for 30 minutes, it automatically turns off the projector lamp and enters

“sleep mode.” This conserves electricity, cools the projector, and extends the life of the lamp. If you are done using the projector, unplug the power cord. If you want to start projecting

again, press the P Power button. You can turn sleep mode on or off through the

Extended menu. See

page 63.

Turn off this product when not in use to prolong the life of the projector.

Shutting Down the Projector

When you’ve finished using the projector, follow the recommended procedure to shut it down.

1. If you’re using a computer, shut it down first; otherwise you may not be able to see your computer’s display to shut it down properly.

2. To turn off the projector, press the P Power button on the projector or remote control.

You see this confirmation message:

(If you don’t want to turn it off, press any other button or wait a few seconds until it disappears.)

3. Press the P Power button again. The projector beeps twice, the lamp is turned off, and the P Power light turns orange. (To turn the projector on again, press the P Power button.)

With Epson’s exclusive Instant Off ® technology there’s no cool-down period, so you can pack up and go immediately after turning off the projector.

4. Press up on the blue foot release lever and lower the projector to retract the front adjustable foot.

5. Attach the lens cover.

caution

To avoid damaging the projector or lamp, never unplug the power cord when the

P Power light is green or flashing orange.

44 Projecting

6. Unplug the power cord.

7. Turn off and disconnect any equipment plugged into the projector.

8. If you won’t be using the projector for awhile, attach the lens cover’s protective pad. Then store it in a protective case.

3

Using the Remote Control

T he remote control lets you access your projector’s features from anywhere in the room—up to 20 feet (6 m) away. For example, you

33 can turn the projector on and off, freeze the presentation, zoom in on a portion of your image, and access the menu system. (The projector

menus let you adjust many projector settings; see Chapter 4.)

When using the remote control, stand within 20 feet (6 m) of the projector. Point the remote control either at the front or back of the projector or at the screen (the projector’s front sensor can detect signals bounced off the screen). Press the button for the function you want to use.

This chapter covers the following information:

■ Controlling the picture and sound

■

Replacing the remote control batteries

45

46 Using the Remote Control

Controlling the Picture and Sound

You can use the remote control to select your source, adjust the colors, temporarily turn off the picture and sound, freeze the action, or zoom in on the picture. Make sure you have set up your projector and

connected any equipment as described in Chapter 1.

Switching Between Picture Sources

If you’ve connected your projector to more than one computer and/or video source, you can use the Source Search button on the projector or remote control to switch between the different sources.

Source Search button

After you select a source, the screen goes dark for a moment before the image appears. The name of the selected source (such as Computer1 or S-Video ) appears briefly on the screen.

Adjusting the Color Mode

You may want to adjust the color mode to select a different setting that is appropriate for the image you’re projecting and the environment in which you’re projecting it. Press the Color Mode button on the remote control.

If you’re projecting computer or RGB video images, the default color mode is Presentation , which is appropriate for full-color presentations in bright rooms.

The following table lists the color modes available.

Color

Mode button

Color mode

Game

Presentation

Text

Theatre

Photo sRGB

Blackboard

Description

Brightest mode, best for playing video games in a bright room.

Use when you’re projecting a full-color presentation in a bright room.

Use when you’re projecting a black and white presentation in a bright room.

Use when projecting movies in a dark room.

Best for projecting still images with vivid color in a bright room (computer input only).

Use when projecting computer images conforming to the sRGB color standard.

Choose this fixed color mode when you need to project against a green blackboard.

You can also use the projector menu system to change the color mode

in the Image menu (see page 57).

Using the Remote Control 47

Turning Off the Picture and Sound

Press the A/V Mute button on the remote control to turn off the image and sound and darken your screen. This is useful if you want to temporarily re-direct your audience’s attention without the distraction of a bright screen.

A/V Mute button

To turn off the picture and sound, press the A/V Mute button. The screen goes dark.

To turn the image and sound back on, press the button again.

You can create an image, such as a company logo or a picture, to display on the screen whenever you press the A/V Mute button. See

page 67 for more information.

Freeze button

Stopping Action

Press the Freeze button to stop the action in your video or computer image and keep the current image on the screen. The sound will continue, however. Also, because the source continues to transmit signals, you won’t resume the action from the point you paused it.

To restart the action, press the Freeze button again.


Zooming Your Image

Follow these steps to zoom in on a portion of the image:

1. Press the E-Zoom + button on the remote control.

You see a crosshair indicating the center of the zoom-in area.

2. Use the four “arrow” buttons on the remote control to position the crosshair in the area you want to enlarge.

3. Continue pressing the E-Zoom + button to enlarge the selected area up to 4 times.

4. While the image is enlarged, you can:

■ Use the arrow buttons to pan about.

■ Press the E-Zoom – button to zoom out.

5. When you’re done, press the E SC

button to return to the original size.

Arrow buttons

E-Zoom buttons

Changing the Image’s Aspect Ratio

You can use the Aspect button on the remote control to change the aspect (width to height) ratio, depending on the input signal.

■ Auto (video images only)

Automatically sets the aspect ratio according to the input signal.

4:3 ratio images display at 4:3, squeeze-recorded signals display at

16:9, and letterbox signals display at Zoom ratio (described below).

■

■

Normal

Displays images using the full projection area and maintains the aspect ratio of the image. 4:3 ratio images project with black bands on the sides, 16:9 images project with black bands on the top and bottom, and 16:10 images use the entire projection area.

16:9

Converts the aspect ratio of the image to 16:9. 4:3 ratio images are elongated horizontally to fit.

Aspect button


■

■

Zoom

Displays images using the full width of the projection area and maintains the aspect ratio of the image. 4:3 ratio images are cut off on the top and bottom.

Full

Displays images using the full width of the projection area, but does not retain the aspect ratio. 4:3 ratio images are elongated horizontally.

■ Through

Displays images as is (aspect ratio and resolution are maintained).

Black bands appear if the resolution is 1280 × 800 or less; images are cut off if the resolution is over 1280 × 800.

Press the Aspect button repeatedly to cycle through the available options.

You can also change the aspect ratio using the projector’s Signal

menu. See page 58 for details.


Replacing the Batteries

The remote control uses two AA alkaline batteries. Follow these steps when you need to replace them:

1. Press in the tab to remove the battery cover.

note

The remote control automatically shuts off when it detects a button being pressed more than

30 seconds. This conserves battery life. It can be helpful, for example, when the remote is in a carrying

case and the P Power button is accidentally pushed.

2. Remove the old batteries, then insert the new ones as shown.

3. Replace the battery cover. (It should click into place.) caution

When replacing batteries, take the following precautions:

■ Replace the batteries as soon as they run out. If a battery leaks, wipe away battery fluid with a soft cloth. If fluid gets on your hands, wash them immediately.

■ Do not expose batteries to heat or flame.

■ Dispose of used batteries according to local regulations.

■ Remove the batteries if you won’t be using the remote control for a long period of time.



4

Fine-tuning the Projector

Y ou can use the Menu button on the projector or remote control to access on-screen menus to adjust the image, sound, and other features.

433


■

■

■

■

■

■

Using the menu system

Adjusting image colors and clarity

Adjusting the input signal

Customizing projector features

Selecting projector setup options

Selecting projector network settings

Viewing lamp usage and other information

Using the projector’s security features

Restoring the default settings

■

■

■

53

54 Fine-tuning the Projector

■

■

■

■

■

■

■

Using the Projector’s Menu System

The projector menus let you adjust and customize the projector features:

The Image menu lets you modify the colors of the projected image and fine-tune brightness, contrast, and sharpness. See

page 56.

The Signal menu lets you make adjustments to the input signal.

You can select your input source, change the image position and aspect ratio, and adjust tracking and sync for computer images.

See page 58.

The Settings menu lets you customize the way you use the projector. It allows you to adjust the volume and keystone correction, set lamp brightness to high or low, control use of the remote control receivers, project a test pattern for adjustments, and disable buttons on the projector while you are projecting. See

page 60.

The Extended menu lets you customize the way you set up the projector. Among the options, you can select the menu language, set rear or ceiling projection, and record a custom image or logo to be displayed as the startup screen or whenever you press the

A/V Mute

button on the remote control. See page 62 and

page 66.

The Network menu lets you select your network settings and optional passwords for monitoring the projector over a network

or over the web. See page 64.

The Info menu provides information about lamp status, and

computer or video settings. See page 64.

The Reset menu lets you restore the projector’s factory default

settings. See page 72.

Changing Menu Settings

Use the buttons on the remote control or on the projector to access the menus and change settings. Follow these steps:

1. Press the Menu button on the remote control or projector to display the menu screen:

Menu options

Menus

The menus are listed on the left, and the options available for the highlighted menu are shown on the right.

2. Use the up and down arrow buttons on the projector or remote control to scroll through the menu list. When you’ve highlighted the desired menu, press the Enter button on the projector or the remote control to select it.

The highlight moves to the first option for that menu.

3. Use the up and down arrow buttons on the projector or remote control to scroll through the list of options. (The options available depend on which source is selected.)

4. After highlighting the option you want to adjust, use the left or right arrow buttons on the projector or the remote control to change the setting. In some cases, you may have to press the Enter button to see a sub-screen for changing the setting.

Fine-tuning the Projector 55


Press the left or right arrow buttons on the projector or the remote control to adjust a slider bar. To select from two or more settings, use the up or down arrow buttons on the projector or the remote control to highlight the desired setting, then press Enter .

5. Press the Esc button to return to the previous menu or to close the menu system if you are at the main menu. Your changes are saved automatically, however you may be prompted to restart the projector to activate some settings.

6. Press the Menu button to exit the menu system.

Adjusting Colors and Clarity

The Image menu lets you make adjustments to the colors of the projected image and fine-tune brightness, contrast, and sharpness.

The options available depend on which image source is selected:

Computer (analog-RGB) and RGB video

Component, composite, and S-Video

Follow these steps to adjust the appearance of your image:

1. Press the Menu button. You see the main menu.

2. Press Enter to select the Image menu.

3. Use the up and down arrow buttons and press Enter to set the following options:

■

■

■

■

Color Mode

Corrects the vividness of image color. You can select from the following settings, and save a different one for each computer and/or video source:

Game: Brightest mode, for playing video games in a bright room.

Presentation: For color presentations in a bright room.

Text: For black and white presentations in a bright room.

Theatre: For optimizing movie images with natural color in a dark room (the default for video or S-Video display).

Photo: For projecting still images with vivid color in a bright room (Computer input only).

sRGB: For standard sRGB computer displays (the default when projecting from a computer with analog video).

Blackboard: Fixed color mode for projecting against a green blackboard.

Brightness

Lightens or darkens the overall image.

Contrast

Adjusts the difference between light and dark areas.

Color Saturation (component, composite, and S-Video)

Adjusts the depth or intensity of the image colors.

note

You can also select High or

Low brightness mode in the

Settings menu. See page 61.


■

■

Tint (component, composite, and S-Video)

Adjusts the balance of green to magenta in the image.

Sharpness

Sharpens or softens the image.

■ Color Adjustment

Adjusts the color temperature and intensity of red, green, and blue.

4. When the image is set correctly, press Esc or Menu .

Adjusting the Input Signal

Although the projector normally detects and optimizes the input signal automatically, you can use the Signal menu to manually select it. You can also change the position of the projected image, correct tracking and sync, and change the aspect ratio to widescreen format.

1. Press the Menu button. You see the Image menu.

2. Select the Signal menu. You see one of the following screens:

Computer (analog-RGB) and RGB video Component video


Composite video and S-Video

3. Press Enter . Then use the up and down arrow buttons and the

Enter button to set the following options:

■ Auto Setup (computer images)

Leave this setting On to automatically optimize the computer image. Turn it off if you want to save adjustments you have made to the video settings.

■

■

Tracking (computer images)

Removes unwanted vertical lines from a computer image by matching the projector’s internal clock to various computer

signals. See page 88 for more information.

Sync (computer images)

Corrects fuzziness or screen flicker by synchronizing the projector with the tracking signal sent from the computer.

See page 88 for more information.

■

■

■

Position

Use the arrow buttons to move the image on the screen left, right, up, or down.

Progressive

Leave this setting On when viewing S-Video or composite video so that interlaced-to-progressive conversion is carried out (best for fast-moving pictures). If you notice flickering while viewing still images, or you are using a component with a 480i signal, switch this setting to Off .

Computer Input ( 1 or 2 )

Selects the signal from equipment connected to the

Computer1 or Computer2 ports. If your image colors look wrong, try changing this setting from Auto to one of the following: RGB for computer or RGB video sources, or

Component Video for component video sources.

note

If you have repositioned the image but then change your mind, you can press the

Enter/Auto button on the remote control to restore the default settings.


■ Video Signal (composite and S-Video)

Leave this setting at Auto unless you are using a 60-Hz PAL system (select PAL60 ).

■ Aspect

Sets the image’s aspect ratio (ratio of width to height). Select

Auto , Normal , 16:9 , Full , Zoom , or Through

; see page 49

for details.

4. When you’re finished, press Esc or Menu .

Customizing Projector Features

The Settings menu lets you customize the way you use the projector, from adjusting lamp brightness and speaker volume to applying security controls.

1. Press the Menu button.

2. Select the Settings menu.



■ Keystone

Adjusts a distorted image from a trapezoid shape to rectangular.

■ Zoom

Adjusts the image size from Wide (larger) to Tele (smaller).


■

■

■

Control Panel Lock

Disables all projector buttons ( Full Lock ) or all the buttons except the P Power button ( Partial Lock ). You can still operate the projector from the remote control. Changes to this setting take effect after you restart the projector. (After you turn off the projector, wait for the P Power light to turn a steady orange before turning it on again.)

Brightness Control

Select Low lamp brightness when the projection is too bright for the room. The Low setting also reduces electricity consumption and fan noise. Select High to project the maximum brightness. (Also check the Brightness setting in

the Image menu; see page 57.)

Volume

Adjusts the volume for the projector’s speaker.

■ Remote Receiver

Deactivates the projector’s front and/or back sensors that detect signals from the remote control. This may be necessary to prevent interference from bright fluorescent lights.

■ Test Pattern

Displays a test pattern to assist you in focusing and zooming the image, and correcting the image shape. (To cancel the displayed test pattern, press Esc .)

4. When you’re finished, press Esc or Menu.

note

To cancel the Control Panel

Lock function from the projector, press the Enter button for about seven seconds.


Selecting Projector Setup Options

Use the Extended menu to customize the way you set up the projector. You can configure the projector for rear and/or ceiling/wall-mounted projection, change the language for the menus and messages, set the screen background color, capture and store a custom image or logo for the startup screen.


2. Select the Extended menu.

note

Captions are not visible when you display the projector menus or use EMP

Monitor to access the projector over a network.



■ Display

Messages: Lets you turn screen messages on or off.

Display Background: Sets the screen background to Black ,

Blue , or Logo when no image signal is available.

Startup Screen: Enables or disables display of the startup screen when the projector is turned on.

A/V Mute: Sets the screen background to Black , Blue , or

Logo when the A/V Mute button is pressed.

Closed Caption : Turns on closed captioning using CC1 or

CC2.


■

■

■

■

User’s Logo

Turn on to display the image or logo you have captured

whenever the projector is turned on. See page 67 details.

Projection

Front: Projector is in front of the screen.

Front/Ceiling: Projector is in front of the screen, mounted upside-down from a wall, whiteboard mounting, or ceiling.

Rear: Projector is behind the screen.

Rear/Ceiling: Projector is behind the screen, mounted upside-down from the ceiling.

To change from Front to Front/Ceiling or Rear to

Rear/Ceiling , press and hold the A/V Mute button on the remote control for five seconds.

Operation

Direct Power On: When this feature is enabled, projection starts as soon as you plug in the power cord. You don’t have to press the P Power button.

Sleep Mode: When enabled, the projector turns off the lamp if it has not received any input signals for a period of time (as defined in the Sleep Mode Timer setting).

Sleep Mode Timer: When Sleep Mode is on, you can set the period of time before the projector turns off automatically, from 1 to 30 minutes.

High Altitude Mode: When using the projector at an altitude above 4,921 feet (1,500 m), turn this setting on to ensure that the internal temperature of the projector is regulated properly. Turn this setting off for lower elevations.

Standby Mode

Select Network On to allow the projector to be monitored over a network when the projector is in standby mode (the

P Power light is orange).

■ Language

Select the language to be used for the projector menus.


note

Logo settings cannot be changed if the User’s Logo

Protect feature has been

turned on. See page 68.

note

When Direct Power On is turned on, press the

P Power button to turn the projector off, wait until

the P Power light turns a steady orange, then unplug the power cord.


Selecting Network Settings

For information connecting the projector to a network and

monitoring the projector over a network, see “Monitoring the

Projector Over a Network” on page 93.

note

You can make changes to many of the signal settings on the Signal menu. See

page 58 for details.

Viewing Lamp Usage and Other

Information

Use the Info menu to view information about the display settings of your computer and the number of hours the lamp has been used.


2. Select the Info menu. You see one of the following menus:

Computer (analog RGB, digital RGB, RGB

Video/Component video)


Video (Composite video, S-Video)

■

■

■

■

■

■

■

Lamp Hours

Displays the number of hours the lamp has been used. The life span of the lamp ranges from about 3000 hours in High brightness mode to about 4000 hours in Low brightness mode. If the number shown is close to 3000 or the information is displayed in red, make sure you have a spare lamp handy.

Source

Displays the input source currently being projected.

Input Signal (computer, RGB video, and component video)

Displays the input signal setting.

Resolution (computer, RGB video, and component video)

Displays the input resolution.

Video Signal (composite and S-Video)

Displays the video signal format.

Refresh Rate (computer, RGB video, and component video)

Displays the refresh rate.

Sync Info (computer, RGB video, and component video)

Provides information that may be needed by the service technician.

■ Status

Displays informations about projector problems. This information may be needed if service is required.


note

The lamp usage timer doesn’t register until you’ve used the lamp for at least

10 hours.


note

If you should happen to enable the password before you set one and you see the prompt to enter the password, enter the default password 0000 to proceed.

Using the Projector’s Security Features

To prevent unauthorized use of the projector, you can do the following:

■

■

■

Create an identifying user logo that is displayed at startup and/or when the A/V Mute button is pressed.

Assign a password to prevent the projector from being turned on, prevent your startup screen from being changed, and lock network settings.

Disable the projector’s buttons; this is useful, for example, if you’re projecting in a classroom and you want to ensure that no one touches the projector’s buttons while you’re using the remote control.

■ Install an anti-theft lock or cable.

If you create a user’s logo for the projector, you can lock the logo on so it is displayed as the startup screen and/or AV/Mute screen.

Unauthorized users cannot turn it off or change it. This feature is intended to discourage theft and provides a way to identify the projector should it be stolen.

If you assign the projector a password, a screen appears requesting the password whenever the projector is turned on. If you enter the password incorrectly three times in succession, the projector’s operation is locked and you’ll need to disconnect the power cord, then reconnect it to redisplay the password screen. If an incorrect password is entered 30 times in a row, the projector is locked and you’ll need to

contact Epson to unlock it. See “Where To Get Help” on page 91.

If someone else will be using the projector for awhile but you want to make sure that person returns it by a certain time, you can temporarily disable the password for a set period. When that time has elapsed, the password is reactivated and must be entered before the projector can be used.

When you enable the Control Panel Lock feature, all of the projector’s buttons ( Full Lock ) or all of the buttons except the P Power button

( Partial Lock ) are disabled.


Creating Your Own Screen Logo

You can transfer any image on your computer to the projector, and then use it as the startup screen and/or the screen that is displayed when you press the A/V Mute button. The image can be a company logo, slogan, photograph, or any other image you want to use. The projector considers this image the “User’s Logo.”

Follow these steps to capture the image and transfer it to the projector:

1. Display the image you want to use on the projector. You can use an image from a computer or video source, such as a DVD player.

2. Press the Menu button and select the Extended menu.

note

If the User’s Logo Protect function is ON , you see a message that the logo cannot be recorded. You’ll need to disable the User’s Logo

Protect function before you can create or change the

User’s Logo. See page 69.

3. Use the down arrow button and press Enter to select User’s

Logo .

4. When you see a message asking if you want to use the present image as a user’s logo, select Yes and press Enter . A selection box displays over the image.

5. Use the arrow buttons on the projector or remote control to select the area of the image you want to use. Once you have selected the area, press Enter .

6. When you see the message Choose this image as the User’s

Logo?

, choose Yes and press Enter . If you want to change the area selected, select No , press Enter and repeat steps 5 and 6.


7. When you see this screen, select a zoom rate (display size), and then press Enter . note

The default setting for the

Startup Screen option menu is On . If the Startup

Screen is set to Off , the logo will not display at startup.

If the User’s Logo Protect function has been set to On , the Display Background setting cannot be changed.

You need to turn the protect function off first. See

page 69 for details.

Once you’ve saved a user’s logo, you cannot reset the logo setting to its factory default (no logo).

8. When you see the message Save image as user’s logo?

, select

Yes and press Enter . Saving the logo takes a few moments. Do not use the projector or other sources (computer, video, etc.) while the logo is being saved. When you see the message

Completed , press Esc .

9. To display the logo as the background screen when you press the

A/V Mute button or when no image signal is available, select the

Extended menu and press Enter . Then select Display , Display

Background , and Logo and press Enter . Select A/V Mute and

Logo and press Enter .

10. When you’re finished, press Menu to exit the menus.

Setting a Password

1. Press the Freeze button on the remote control for about five seconds until you see the Password Protect menu: note

If a password has already been set, you see the

Password Protect Release

screen. See “Starting the

Projector with a Password” on page 70.

2. Select Password and press Enter .


3. When you see the message Change the password?

, select Yes and press Enter .

4. Enter a 4-digit number using the numeric buttons on the remote control, as shown.

The password will be displayed as **** . After you enter the last digit, a confirmation screen appears. Enter the password again.

You see the message Password accepted .

Numeric buttons

5. After you finish setting the password, press the Esc button to return to the Password Protect menu.

Make a note of the password and keep it in a safe place in case you forget it.

Turning On the Password and User’s Logo

1. Press the Freeze button on the remote control for about five seconds until you see the Password Protect menu.

2. To enable the password, select Power On Protect and press

Enter . Select On then press Esc .

3. To enable your screen logo, select User’s Logo Protect and press

Enter . Select On then press Esc .

When this feature is on the logo appears whenever the projector is turned on (if the Startup Screen is enabled in the Extended

menu; see page 62) and as the A/V Mute screen (if you selected

the Logo as the Display Background in the Extended menu).

None of the User’s Logo features can be changed when the User’s

Logo Protect function is enabled.

4. To lock the network settings in the menu system, select Network

Protect and press Enter . Select On and press Enter .

5. Press Menu to close the Password Protect menu.

If you lose the remote control, you will not be able to enter the password, so keep the remote control in a safe place at all times.

You can attach the password protect sticker to the projector as an additional theft deterrent.


Starting the Projector with a Password

When the password function is enabled, you see this screen when you turn on the projector:

Use the numeric buttons on the remote control to enter the password.

Once you have entered the password correctly, the password screen closes, and projection begins.

If the password is not correct, you see the message Wrong password.

Please try again.

If you enter an incorrect password three times in succession, you see the message The projector’s operation will be locked. Request code xxxxx and the projector switches to standby mode for approximately 5 minutes. Write down the request code.

Then disconnect the projector’s power cord from the electrical outlet, reconnect it, and turn the projector back on.

When you see the Password Protect Release screen again, you can try to enter the correct password.

If you enter an incorrect password 30 times in succession, the projector remains locked and you must contact Epson for service.

If you have forgotten the password, contact Epson with the request code number that appears in the Password Protect Release screen for

assistance. See “Where To Get Help” on page 91.


Disabling the Projector’s Buttons

You can use the Control Panel Lock function to disable all the projector’s buttons, or all the buttons except for the P Power button.


2. Select the Settings menu and press Enter .

3. Use the up and down arrow buttons to select Control Panel Lock and press the Enter button.

4. Select Full Lock to disable all the buttons, or Partial Lock to disable all except the P Power button.

Then press Enter .

5. Select Yes and press Enter to confirm the setting.


note

To cancel Control Panel

Lock, press the projector’s

Enter button for 7 seconds.

Installing Security Locks

You can install two different types of security locks on the projector:

■

■

You can use the security slot on the base of the projector to install

a Kensington Microsaver Security System. See page 13.

You can use a wire lock to secure the projector to a room fixture or heavy furniture, as shown below.


note

The Computer Input (1 and

2), User’s Logo, Network menu settings, Lamp Hours, and Language settings do not return to their defaults when you select Reset All .

To reset the computer inputs, use the Reset option on the Signal menu; see

page 58 for details. To reset

the network settings, use the

Reset option on the

Network menu; see page 64

for details. To reset the

Language settings, use the

Reset option on the

Extended menu; see page 62

for details.

Restoring the Default Settings

The Reset menu lets you return most projector menu settings to their default values. It also lets you reset the lamp hours to their initial

default value; see page 79 for instructions on resetting the lamp timer.

To reset most projector menu settings, select Reset All and press the

Enter button to display the confirmation screen. Select Yes to reset all the default settings or No to cancel.


warning

Before you clean any part of the projector, turn it off and unplug the power cord.

Never open any cover on the projector, except the lamp and filter covers. Dangerous electrical voltages in the projector can injure you severely. Do not try to service this product yourself, except as specifically explained in

this User’s Guide. Refer all other servicing to qualified service personnel.

5

Maintenance and

Transportation

Y our projector needs little maintenance. All you need to do on a regular basis is keep the lens clean. Any dirt or smears on the lens may show up on your projected image.

You may need to clean the air filter and air vents. A clogged air filter or air vent can block ventilation needed to cool the projector and cause overheating.

The only parts you should replace are the lamp and air filter. If any other part needs replacing, contact your dealer or a qualified servicer.

This chapter covers the following:

■ Cleaning the lens

■

■

Cleaning the projector case

Cleaning and replacing the air filter

■

■

■

Replacing the lamp

Resetting the lamp timer

Transporting the projector

5

73

caution

Do not use glass cleaner to clean the lens.

Avoid touching the lens with your bare hands to prevent fingerprints on or damage to the lens surface.

Cleaning the Lens

Clean the lens whenever you notice dirt or dust on the surface.

■ Use a canister of compressed air to remove dust.

■ To remove dirt or smears on the lens, use lens-cleaning paper. If necessary, moisten a soft cloth with lens cleaner and gently wipe the lens surface.

Cleaning the Projector Case

Before you clean the case, first turn off the projector and unplug the power cord.

■ To remove dirt or dust, wipe the case with a soft, dry, lint-free cloth.

■

■

To remove stubborn dirt or stains, moisten a soft cloth with water and a mild detergent. Then wipe the case.

Do not use wax, alcohol, benzene, paint thinner, or other chemical detergents. These can damage the case.

Cleaning and Replacing the Air Filter

Your projector includes an air filter to ensure the best performance. If dust collects on the air filter or vent on the side of the projector, clean them as described below. Dust clogs prevent proper ventilation and can cause overheating and damage the projector.

When the filter and vent are clogged, the projector displays the message The projector is overheating. Make sure nothing is blocking the air vent, and clean or replace the air filter.

74 Maintenance and Transportation

To clean the air filter and air vent, follow these steps:

1. Turn off the projector, allow it to cool down, and unplug the power cord.

2. To clean the filter and vent, Epson recommends using a small vacuum cleaner designed for computers and other office equipment. If you don’t have one, gently clean them using a very soft brush (such as an artist’s paintbrush).

You can remove the air filter to clean both sides.

Vent

If the dirt is difficult to remove or if the filter is torn, replace it.

Contact your dealer or call Epson at (800) 463-7766 to obtain a new one (part number V13H134A13).

3. If you need to clean or replace the filter, slide it out, as shown.

Maintenance and Transportation 75

note

Air filters contain polycarbonate, ABS resin, and polyurethane foam.

Dispose of used air filters according to local regulations.

4. Align the new filter and slide it in until it clicks into place.

note

You can check to see how many hours the lamp has

been used. See page 64.

Turn off this product when not in use to prolong the life of the projector. warning

Let the lamp cool before replacing it. If the lamp breaks, handle the shards carefully to avoid injury.

Replacing the Lamp

The projection lamp typically lasts for about 3000 hours of use

(in high brightness mode) or 4000 hours (in low brightness mode). It is time to replace the lamp when:

■

■

■

The projected image gets darker or starts to deteriorate.

The lamp light is flashing orange.

The message Replace the Lamp appears on the screen when the lamp comes on. To maintain projector brightness and image quality, replace the lamp as soon as possible.

Contact your dealer or call Epson at (800) 463-7766 for a replacement lamp. Request part number V13H010L42.

Follow these steps to replace the lamp:

1. Press the P Power button twice to turn off the projector. When you hear the projector beep twice, unplug the power cord.

2. If the projector has been on, allow it to cool down for at least an hour (or until the lamp is cool).


3. Use the screwdriver included with the replacement lamp or a

#2 Phillips-head screwdriver to loosen the screw holding the lamp cover (the lamp cover is located on top of the projector).

4. Slide the cover out, then lift it off.

5. Use the screwdriver to loosen the two screws holding the lamp in place. (You can’t remove the screws.)

6. Hold the lamp as shown and pull it straight out.

Don’t remove these screws note

The lamp(s) in this product contain mercury.

Please consult your state and local regulations regarding disposal or recycling. Do not put in the trash.


caution

Do not touch the glass portion of the lamp assembly. Touching the glass could result in premature lamp failure.

7. Gently insert the new lamp along the guide rail. If it doesn’t fit easily, make sure it’s facing the correct way. Push the lamp down firmly where the label PUSH appears.

8. Once the lamp is fully inserted, tighten its screws.

note

Be sure to seat the lamp fully and secure the lamp cover. If the lamp is not properly installed or the cover is loose, the lamp will not turn on.

9. Lower the lamp cover into place. (The opening should be almost covered, and the top of the cover should be flush with the top of the projector.) Then slide the cover closed and tighten the screw.

10. Reset the lamp timer as described in the next section.


Resetting the Lamp Timer

You must reset the lamp timer after replacing the lamp to clear the

Replace the Lamp warning message. Follow these steps:

1. Connect the power cable and turn on the projector.

2. Press the Menu button on the remote control or projector and select the Reset menu. Then press Enter .

note

Do not reset the lamp timer if you have not replaced the lamp. If you do, the Lamp

Hours will not accurately reflect the number of hours that the lamp has been used.

3. Select Reset Lamp Hours and press Enter . You see a confirmation screen.

4. Select Yes and press Enter .

5. Press Esc to return to the main menu or the Menu button to exit the menu system.


note

Epson shall not be liable for any damage incurred during transportation.

Transporting the Projector

The projector contains many glass and precision parts. If you need to transport it, please follow these packing guidelines to prevent damage to the projector:

■ Whenever you transport the projector, always attach the lens cover and the protective pad that fits over the lens cover to protect the lens.

■

■

■

When shipping the projector for repairs, use the original packaging material if possible. If you do not have the original packaging, use equivalent materials, placing plenty of cushioning around the projector.

When transporting the projector as freight or checked luggage, first put it in a carrying case, then pack it in a firm box, using cushioning around the case. Make sure the shipping carrier is equipped to handle fragile equipment and mark the box “Fragile.”

When you are hand-carrying the projector, be sure to use a carrying case.


6

Solving Problems

T his chapter helps you solve problems with your projector, and tells

6 you how to contact technical support for problems you can’t solve yourself. This chapter explains the following:

■

■

■

■

Using the projector’s on-screen help system

What to do when the projector’s status lights flash

Solving problems with the image or sound

Solving password problems

Solving problems with the remote control

Solving problems monitoring the projector over a network

Contacting technical support

■

■

■

81

82 Solving Problems

Using On-Screen Help

If the image doesn’t look right or your audio isn’t working, you can get help by pressing the ?

Help button on the projector or remote control.

1. Press the ?

Help button on the remote control or projector. You see the Help menu.

2. Use the up and down arrow buttons on the projector or remote control to highlight the problem you want to solve. Then press the Enter button to view the solution(s).

3. Press Esc to view another topic or press ? Help to exit.

If none of the suggestions solves your problem, see additional solutions to problems in the following sections.

What To Do When the Lights Flash

The lights on top of the projector indicate the projector’s status and let you know when a problem occurs.

Power light

Lamp light

Temperature light

If the projector is not working correctly, first turn it off and unplug it.

Then plug the power cord back in and turn on the projector. If this does not solve the problem, check the status lights on top of the projector and try the solutions recommended in the following table.

Power light

Green

Flashing green

Orange

Lamp light

Off

Off

Flashing orange

Red

Red

Red

Orange

Red

Flashing red

Temperature light Description

Off

Off

The projector is operating normally.

The projector is warming up. Wait for the image to appear.

Off

Off

Off

Off

Flashing red

Flashing orange

Off

Flashing red

Off

Off

Flashing orange

Red

Off

Off

Flashing red

Flashing red

The projector is in standby or sleep mode. You can unplug it or press the P Power button to turn it on.

The projector is shutting down. Wait for the light to stop flashing and remain orange before unplugging it.

The projector is too hot. Make sure the temperature surrounding the projector does not exceed 95 ° F (35 ° C) and there is plenty of space around and under the projector for ventilation. Clean the air filter and air vents, if

necessary. See page 74 for instructions.

The projector has overheated and turned itself off. Let it cool for about five minutes, then turn it back on. Make sure there is plenty of space around and under the projector for ventilation. If you are using the projector at an altitude above 4921 ft (1500 m), turn on High Altitude Mode as the

Operation setting in the Extended menu; see page 62. Also

clean the air filter and air vents; see page 74. If it continues

to overheat, you may need to replace the air filter.

The lamp is burned out, broken, or not installed correctly; or the lamp cover is open. Close the cover or replace or

reseat the lamp, if necessary, as described on page 76.

Also clean the air filter and air vents; see page 74. If you

are using the projector at an altitude above 4921 ft

(1500 m), turn on High Altitude Mode as the Operation

setting in the Extended menu; see page 62. If these

suggestions don’t work, contact Epson.

Replace the lamp with a new one as soon as possible; see

page 76 for instructions. If you continue to use the lamp,

there is a risk it may break.

There is a problem with the fan or a sensor. Turn the projector off and unplug it. Contact Epson for help; see

page 91.

There is an internal error in the projector. Turn the projector

off and unplug it. Contact Epson for help; see page 91.

Solving Problems 83


Solving Problems with the Image or

Sound

No image appears on the screen.

■ Check that the P Power light is green, not flashing, and the lens cover is removed. Also press the A/V Mute button on the remote control to see if the picture was turned off temporarily.

■

■

■

■

■

■

■

■

If the projector doesn’t turn on, the Control Panel Lock may be enabled. Press and hold the Enter button on the projector for

7 seconds to release the lock.

The projector may be in standby or sleep mode. If the projector has not received any signal for 30 minutes, it turns off the lamp to conserve the lamp life and save energy. If the P Power light is orange, press the P Power button to turn on the projector.

The attached computer may also be in sleep mode or displaying a black screen saver. Try pressing a key on the computer.

If the power was switched off and then on again, wait until the

P Power light stops flashing and remains orange. Then press the

P Power button again.

Check the Video Signal , Computer1 Input , or Computer2

Input setting in the Signal menu to make sure it is correct for the

selected source. See page 58 for more information.

Messages may have been turned off in the Display setting of the

Extended menu. See page 62 for details.

Adjust the Brightness

setting on the Image menu (see page 57)

or select High for the Brightness Control setting in the Settings

menu (see page 61).

With Direct Power On enabled in the Operation setting of the

Extended menu, if you unplug the projector and then plug it right back in, you must press the P Power button to turn on the

projector. See page 62 for details.

Make sure at least one of the projector’s remote receivers are

turned on in the Settings menu. See page 60 for details.

Nothing appears on the external monitor.

■ Make sure the VGA computer cable is connected to your computer’s video port and the projector’s Computer1 port.

■ Make sure the cable from your monitor is connected to the projector’s Monitor Out port.

You see a blue screen with the message

No Signal

displayed.

■ Make sure the cables are connected correctly, as described in

Chapter 1.

■

■

■

Make sure the power to your computer or video source is turned on.

If you’ve connected a computer and one or more video sources, you may need to press the Source Search button on the projector or the remote control to select the correct source. Allow a few seconds for the projector to sync up after pressing the button.

If you’ve connected a laptop computer, make sure it’s set to

display on an external monitor. See page 38.

The message

Not Supported

is displayed.

■ Make sure your computer’s resolution doesn’t exceed WXGA+

and the frequency is supported by the projector; see page 109. If

necessary, change your computer’s resolution setting as described

on page 86.

■ Make sure the correct Video Signal is selected in the Signal

menu. See page 60. It should normally be set to

Auto .

The buttons on the projector don’t work.

The Control Panel Lock may be enabled. Press and hold the Enter button on the projector for 7 seconds to release the lock.



Only part of the computer image is displayed.

■ If you’re projecting from a computer or RGB video device, press the Enter/Auto button on the remote control. If this doesn’t work, you may need to adjust the Position setting in the Signal

menu. See page 59 for more information.

■

■

■

■

If you’ve enlarged part of the image using the E-Zoom button on the remote control, press the Esc button to cancel zooming and return to full display.

Try pressing the Aspect button on the remote control to select a

different aspect ratio. See page 49 for details.

Make sure your computer’s resolution setting is correct and dual display is not activated. Ideally, it should be 1280 × 800 to match the projector’s native resolution. If this option isn’t available,

select another compatible video format. See page 109.

■ Windows:

Right-click the desktop, select Properties , click the Settings tab, and select a different resolution.

■ Macintosh OS X:

On the Apple menu, choose System Preferences , then click Display or Displays . Select a different resolution.

You also may need to modify existing presentation files if you created them for a different resolution. See your software documentation for specific information.

The image isn’t rectangular, but trapezoid-shaped.

■ Make sure the projector isn’t placed off to one side of the screen, at an angle, or the image won’t be rectangular. Place it directly in front of the center of the screen, facing the screen squarely.

■ If you’ve tilted the projector upward, the image will be broader at the top. Hold down the or buttons on top of the projector until the image is rectangular.

The image contains static or noise.

■ If you’re using a computer cable longer than 6 feet (2 m), or an extension cable, the image quality may be reduced.

■

■

■

■

■

■

Keep your computer and video cables separated from the power cord as much as possible to prevent interference.

The video signal may be split between the computer and the projector. If you notice a decline in the projected image quality when the image is displayed simultaneously on your laptop computer and the projector, turn off the laptop’s LCD display.

If you’re projecting from a composite or S-Video source, check the Video Signal setting in the Signal menu. In most cases, leave it set at Auto . If you’re using a 60-Hz PAL video source, change this setting to PAL60 . Also make sure the Progressive setting is

On

. See page 60 for details.

Make sure the cables are securely connected at both ends.

Select the correct resolution; see “Compatible Video Formats” on page 108.

If you’re projecting from a computer, press the Enter/Auto button on the remote control or the Enter button on the projector to adjust tracking and sync automatically. If that doesn’t work, try adjusting the Sync and Tracking settings in the Signal

menu. See page 59.

The image is blurry.

■

Adjust the focus using the focus ring. See page 40.

■

■

■

■

Try cleaning the lens as described on page 74.

Make sure the lens is not fogged by condensation. You may need to wait before using the projector after moving it from a cold environment.

Make sure the projection distance is within the ranges described

on page 16 through page 18.

Adjust the Sharpness

setting on the Image menu (see page 58).

You should be able to see the effect on the screen immediately.


note

Because of the different technologies used, your projected image may not exactly match the colors on your laptop or computer monitor.

You see vertical stripes or the image still looks blurry after trying the solutions in the previous section.

■ If you’re projecting from a computer and displaying an image that contains a lot of fine detail, you may notice one or more vertical stripes or bands, or some of the characters may look heavy or blurred. Press the Enter/Auto button on the remote control to automatically reset the projector’s tracking and sync settings.

■ If necessary, you can manually adjust the Tracking and Sync

settings on the Signal menu as described on page 59.

To help you adjust these settings, fill the screen with a detailed image, such as a desktop background pattern or black text on a white background. Adjust the Tracking setting to eliminate vertical stripes; adjust the Sync setting to increase the sharpness.

The colors of the image are not right.

■

Try selecting a different Color Mode. See page 57 for

instructions.

■

■

■

■

■

If you’re displaying video, adjust the Color Saturation and Tint

settings on the Image menu. See page 57 for instructions.

Adjust the Brightness , Contrast , and Color Adjustment

settings on the Image menu. See page 57.

Make sure the input signal setting on the Signal menu matches

the signal from the connected device. See page 58 for details.

If the image is too purple and you’ve connected a computer or other RGB device to the Computer1 or Computer2 port, select

RGB as the input source. If you’ve connected a component video device to one of these ports, select Component Video .

If you’re projecting from a composite video or S-Video source, select the correct Video Signal in the Signal menu.

Check your computer display settings to correct the color balance.

If the image seems dark, the lamp may be nearing time for

replacement. Check the lamp hours as described on page 64 and

replace the lamp, if necessary, as described on page 76.


There is no sound.

■ Press the Vol+ button on the remote control to turn up the volume.

■

■

■

■

■

If you’ve turned off the picture and sound, press the A/V Mute button on the remote control to turn them on again.

If you’re using a DVD player or other video source, make sure its volume is not turned all the way down or muted. Also, make sure

the cables are connected correctly, as described in Chapter 1.

Make sure the audio cable is connected to the correct audio port.

See page 24 or page 31.

If your presentation includes computer audio, make sure the volume control on your computer is not turned all the way down or muted. Make sure the audio cable is securely connected to both

the projector and your computer. See page 24.

The wrong source may be selected. Press the Source Search button on the projector or the remote control.

Solving Password Problems

You have forgotten the password.

■ Write down the request code that appears in the Password Protect

Release screen and contact Epson. See page 91.

■ If you turned on the password protect feature before setting the password and no password was set before, try using the default password: 0000 .

The remote control is not available.

You must have the remote control to enter the password. You can

purchase a replacement remote control from Epson. See page 92.


30°

30°

20 feet

(6 m)

Solving Problems with the Remote

Control

The projector doesn’t respond to remote control commands.

■ Make sure you are within 20 feet (6 m) of the projector, and within range of the projector’s front or back sensor. The effective range is approximately 30° to the left or right, 30° above or below the rear sensor, and 60° above the front sensor (below, if mounted upside-down).

60°

30°

30°

30°

30°

■

■

■

■

20 feet

(6 m)

20 feet

(6 m)

20 feet

(6 m)

If a button on the remote control is held for more than

30 seconds, the remote enters sleep mode. Press another button for normal operation.

The remote control batteries may not be installed correctly or may

be low on power. Replace the batteries as described on page 51.

Dim the room lights and turn off any fluorescent lights. Make sure the projector is not in direct sunlight. Strong lighting, especially fluorescent lights, may affect the projector’s infrared receivers. If you still have trouble using the remote control, disable one of the remote receivers using the Settings menu to block

interference from bright light. See page 60 for details.

Turn off any nearby equipment that emits infrared energy, such as a radiant room heater.

You have lost the remote control.

You need the remote control to access many projector features. If you

have lost it, you can order another from Epson; see page 92 for details.


Solving Network Problems

You don’t see your projector in the EMP Monitor window.

■ Make sure that you’ve connected the projector to the network and

configured it correctly; see page 95. Also, make sure you’ve

registered the projector with EMP Monitor; see page 99.

■

■

■

Make sure that Standby Mode in the projector’s Extended menu is set to Network On

; see page 62.

If the computer you are using is running Windows XP or 2000, or Windows Vista,

®

you must be logged in as the Administrator.

Try restarting your computer.

You don’t receive an e-mail over the network when a projector problem occurs.

■ Make sure that Standby Mode in the projector’s Extended menu is set to Network On

; see page 62.

■

■

Make sure that you’ve connected the projector to the network and

configured it correctly; see page 95.

Make sure you set up projector e-mail alerts correctly in the

Network menu (see page 97) or in EMP Monitor (see page 102).

Where To Get Help

Epson provides these technical support services:

Internet Support

Visit Epson’s support website for solutions to common problems with the PowerLite 400W. You can download utilities and documentation, get FAQs and troubleshooting advice, or e-mail Epson with your questions.

Visit Presenters Online to access tips, templates, and training for developing successful presentations.


note

To purchase a replacement remote control, call

(562) 276-4394 (U.S.) or

(905) 709-3839 (for dealer referral in Canada).

Speak to a Support Representative

To use the Epson PrivateLine Support service, call (800) 637-7661 and enter the PIN on the included Epson PrivateLine Support card.

This is the fastest way of speaking to a live representative, and it’s free.

This service is available 6

AM

to 6

PM

, Pacific Time, Monday through

Friday, for the duration of your warranty period.

You may also speak with a projector support specialist by dialing one of these numbers:

■ U.S.: (562) 276-4394, 6 AM to 6 PM , Pacific Time, Monday through Friday

■ Canada: (905) 709-3839, 6

AM

to 6

PM

, Pacific Time, Monday through Friday

Days and hours of support are subject to change without notice. Toll or long distance charges may apply.

Before you call, please have the following information ready:

■ Product name (PowerLite 400W)

■

■

Product serial number (located on the bottom of the projector)

Proof of purchase (such as a store receipt) and date of purchase

■

■

Computer or video configuration

Description of the problem

Purchase Supplies and Accessories

You can purchase screens, carrying cases, or other accessories from an

Epson authorized reseller. To find the nearest reseller, call

800-GO-EPSON (800-463-7766). Or you can purchase online at

www.epsonstore.com (U.S. sales) or www.epson.ca (Canadian sales).


7

Monitoring the Projector

Over a Network

T he software included with your projector lets you monitor and control your projector over a network.

■

■

Use EMP Monitor (available for Windows only) to see your projector’s status, switch image sources, and control basic settings.

Use the mail notification function to receive e-mail alerts about possible problems.

To use the software to manage your projectors, first install EMP

Monitor. Then connect and configure the projector you want to monitor as described here.


■ Installing the network software

■

■

■

■

Connecting your projector to a network

Selecting network settings

Monitoring and controlling your projector with EMP Monitor

Using a browser to monitor the projector

7

93

Installing the Network Software

The network software CD-ROM includes the software you need to monitor the projector from a remote location. The Epson Projector

Software CD-ROM includes EMP Monitor for monitoring the projector from a remote location.

Windows System Requirements

Before you install the software, make sure your computer meets these requirements:

■

■

■

■

■

Microsoft Windows 98SE, Me, or 2000 (SP4), Windows XP, or

Windows Vista

IBM ® compatible PC with at least a Pentium ® III 1.2 GHz processor

At least 256MB of RAM (512 recommended)

At least 128MB of free hard disk space

XGA (1024 × 768) or better display adapter and monitor, 16-bit color or higher

Installing the Software on a Windows System

1. Insert the network software CD-ROM in your computer’s

CD-ROM or DVD drive.

2. Click Custom , then make sure EMP Monitor is selected.

3. Click Install , then follow the on-screen instructions to install your projector software.

4. When installation is complete, click Exit .

94 Monitoring the Projector Over a Network

Connecting to the Network

Follow these steps to connect the projector to your network and configure it with an IP address.

1. Connect the projector to your network using a commercially available 100BaseTX or 10BaseT network cable. Connect the cable to the LAN port on the projector.

2. Press the projector’s P Power button to turn it on.

Monitoring the Projector Over a Network 95

Selecting Network Settings

Follow the instructions in this section to set up the projector’s network settings in the menu system.


2. Select the Network menu.



■

■

Wired LAN

If your network assigns addresses automatically, turn on the

DHCP setting.

If your network does not assign addresses automatically, turn off DHCP and enter the projector’s IP Address , Subnet

Mask , and Gateway Address as needed.

To enter numbers, use the numeric buttons on the remote control.

PJLink Password

Lets you enter a password for using the PJLink ™ protocol to control the projector.

■ Web Control Password

Lets you enter a password for accessing the projector over the web from a computer running the EMP Monitor software.


■

■

■

■

SNMP

If you’re a network administrator, you can use the SNMP option to enter trap IP addresses. This lets you receive trap alerts for the projector on a computer running the SNMP

Manager software.

Mail

When enabled, the projector sends you an e-mail alert if it has any problems. For instructions on setting up e-mail alerts, see the next section.

Projector Name

Enter a name for identifying the projector over the network.

AMX Device Discovery

Turn on to allow the projector to be detected by AMX ®

Device Discovery-enabled software, if you are using it on your network.

Using Projector E-mail Alerts

When this feature is enabled, the projector sends you an e-mail alert if it has any problems.

1. Press the Menu button, select the Network menu, and press

Enter .

2. Select Mail and press Enter .

3. Select the following settings as necessary:

■ Mail Notification

Select On to enable sending of an e-mail if there is a problem with the projector.

■ SMTP Server

Enter the IP address for the SMTP server for the projector.

You can enter a number from 0 to 255 in each field of the address.

■ Port Number

Enter the SMTP server’s port number. The default value is

25. You can enter a numeric value from 1 to 65535.

note

You can also set e-mail alerts from EMP Monitor (see

page 102).


note

If a critical problem develops with a projector which causes it to suddenly stop working, it may not be possible for the projector to send a message.

If Standby Mode is set to

Network On in the

Extended menu, the projector can still be monitored even if the projector is in standby mode

(when the power is off).

■

■

■

■ Address 1/2/3 Setting

Choose one of the Address numbers, then enter the e-mail address where you want to receive a message when a problem occurs and select the condition under which you want to receive a message.

4. When you’re done, press Menu to exit the menu system.

When a problem occurs, an e-mail message is sent to the specified addresses with the subject line EPSON Projector and the following information:

Line 1: The name of the projector where the problem has occurred

Line 2: The IP address of the projector where the problem has occurred

Line 3: Details of the problem note

If you want to monitor the projector while it is in standby mode, select

Standby Mode in the

Extended menu, then select

Network On

. See page 62.

Using EMP Monitor

EMP Monitor lets you use a remote computer to manage your projectors. It lets you easily turn the projector on or off, switch image sources, and check its status.

Before using EMP Monitor, make sure you’ve installed the software

(available for Windows only) as described on page 94. The computer

you’re using to monitor the projector should already be connected to your network.

Opening and Closing EMP Monitor

To start EMP Monitor, click Start > Programs or All Programs >

EPSON Projector > EMP Monitor .

If you’ve added the program to the Startup programs folder, it may already be open. If so, click the icon in the system tray on the lower-right corner of your screen to start EMP Monitor:

Click here to start

EMP Monitor


To close EMP Monitor, select Exit from the File menu or right-click the program icon shown above, then select Exit .

Registering a Projector

Before you can monitor a projector, you have to register it. Follow these steps to automatically search for your projector.

1. Open EMP Monitor.

2. Select Edit > New > Projector (automatic search) .

3. Click Search to locate projectors currently operating on the network.

4. Select the projector you want to add by clicking its name, then click the Edit button.

5. Enter a Display name, select a Parent group, if necessary, enter a

Monitor Password, if necessary, and a Description for the projector.

6. Click the Register button.

7. Repeat steps 2 through 5 to register any additional projectors on

the network.

8. When you’re done adding the projector, click Cancel . You see a screen with a list of all registered projectors:

Monitoring Your Projector

The EMP Monitor screen lets you monitor your projector status and check if a problem has occurred.

For the most current status, click the Refresh button. note

If the projector is not automatically found, your projector may not be connected or configured correctly for the network. See

page 95.

To delete a projector from the list, right-click the projector name, and click

Delete .

note

To monitor a projector when it’s in standby mode

(plugged in but not turned on), you must select

Network On as the

Standby Mode setting in the projector’s Extended

menu (see page 62).

For detailed status information, right-click the projector and click

Property .


The following table describes the EMP Monitor status icons.

Group status icons

No warnings or problems in the projector group.

Warning or problem in a projector in the group.

Monitoring disabled. Right click the icon and select

Monitoring Enabled to begin monitoring the group.

Data is currently being updated.

Type status icons

No warnings or problems.

Warning or problem.

Monitor Password error. No monitor password was entered when you registered the projector, or an incorrect password was entered.

Monitoring disabled. Right-click the icon and select

Monitoring Enabled to monitor the projector.

Data is currently being updated.

Network error (projector is not connected to the network, the power cable is disconnected, or

Network Off is selected as the Standby Mode

setting in the Extended menu; see page 62).

Network error (Esc/VP.net communication error).

Power status icons

The projector is powered on; normal status.

The projector is powered off; normal status.

The projector is powered on; abnormal status.

The projector is powered off; abnormal status.


Temperature level status icons

The projector’s internal temperature is normal (low).

The projector’s internal temperature is normal

(medium).

The projector’s internal temperature is normal (high).

The projector’s internal temperature is high

(high-temperature warning).

The projector’s internal temperature is too high

(high-temperature error). The projector is turned off automatically.

Error status icons

Lamp life warning. The lamp is nearing the end of its life.

High-temperature warning. The projector is getting too hot but continues to operate.

Replace air filter.

No air filter. The air filter is not installed or installed incorrectly.

Low air flow. The air filter needs to be cleaned or replaced.

Air flow sensor error. Contact Epson as described on

page 91.

Lamp cover open. Close the lamp cover.

Lamp out. The lamp has reached the end of its life.

Lamp failure at power on. The lamp has reached its end of life or is installed incorrectly.

High internal temperature error. The projector is turned off automatically.

Internal (system) error. Contact Epson as described

on page 91.


Fan error. Contact Epson as described on page 91.

Sensor error. Contact Epson as described on

page 91.

Other error. Contact Epson as described on page 91.

note

You can also set e-mail alerts from the projector’s menu

system (see page 97).

note

If a projector develops a critical problem, it may not be possible for it to report the error.

Using E-mail Alerts

You can set up e-mail alerts to warn you of problems with the projector.

1. Open EMP Monitor.

2. From the Tool menu, select Mail notification function .

3. Turn the Mail notification function setting On .

4. Enter the IP address and port number of your network’s SMTP

(outgoing) mail server.

5. Enter the Sender (projector) mail address.

6. Enter up to three e-mail addresses to send alerts to in the

Recipient mail address boxes.

7. Click the Notification event buttons to select the conditions under which an e-mail alert will be sent.

8. When you’re done, click the OK button.

If a projector experiences a problem, EMP Monitor sends an e-mail message to each of the addresses you entered in the Set mail notification function window. The subject line and body of the message includes the projector’s name and the warning or error

(similar to the those listed on page 99).

When the problem has been fixed, EMP Monitor sends a message indicating the problem has been resolved.


Using a Browser to Monitor the

Projector

If your projector is connected to a network, you can use a standard web browser to monitor and control it. When using a browser to access the projector, you cannot connect through a proxy server.

1. Make sure that the projector is connected to your network, as

described on page 95.

2. Follow the instructions on page 62 to set

Standby Mode to

Network On in the Extended menu so you can monitor the projector in standby mode.

3. Open your web browser and enter the IP address of the projector you want to monitor in the browser window.

If you’re not sure what the address of the projector is, turn the projector on and select Wired LAN from the Network menu to

display the IP address of the projector. See page 96.

You see a login screen.

4. Do one of the following:

■ If you didn’t set a Web Control Password in the Network menu, click OK .

■ If you set a Web Control Password in the Network menu, enter it in the Password box, then click OK .

You see a screen displaying the settings you can change.

5. Select one of the menu options, then change any settings as needed. These settings correspond to those found in the

projector’s menu system. See page 54 for details.

You cannot change the User’s Logo , High Altitude Mode , and

Language settings in the Extended menu or select the Reset All and

Reset Lamp Hours in the Reset menu.

Use the controls at the bottom of the screen to choose a source, stop the action, turn off the picture and sound, or turn the projector’s power on or off.



A

Technical Specifications

General

Type of display Poly-silicon TFT active matrix

Lens F=1.8

Focal length: 6.48 mm

1280 × 800 pixels (WXGA) Resolution

Color reproduction

Brightness (ANSI)

Full color, 16.77 million colors

1800 lumens (High brightness mode)

1420 lumens (Low brightness mode)

500:1 Contrast ratio

Image size

Projection distance

Projection methods

Focus adjustment

44 to 110 inches (1.1 to 2.8 m)

21 to 48 inches (0.53 to 1.22 m)

Front, rear, ceiling

Manual

Zoom adjustment Digital

Internal sound system 10 W monaural

Optical aspect ratio

Zoom ratio

16:10 (horizontal:vertical)

1:1.35

A

105

note

Lamp life results will vary depending upon mode selected, environmental conditions and usage. Lamp brightness decreases over time.

Noise level 35 dB (High brightness mode)

28 dB (Low brightness mode)

Keystone correction angle ± 15° vertical (maximum)

Projection Lamp

Power consumption 170 W UHE

Lamp life About 3000 hours (High brightness);

4000 hours (Low brightness)

Remote Control

Range

Batteries (2)

20 feet (6 m)

Alkaline AA

Dimensions

Height

Width

Depth

Weight

Electrical

Rated frequency

Power supply

Power consumption

6.2 inches (157 mm)

12.9 inches (327 mm)

10.7 inches (272 mm)

7.9 lb (3.6 kg)

50/60 Hz

100 to 120 VAC, 2.8 A

200 to 240 VAC, 1.2 A

Operating: 251 W

Standby: 4.2 W (network off)

4.9 W (network on)

106 Technical Specifications

Environmental

Temperature

Humidity

Altitude

Operating: 41 to 95 °F (5 to 35 °C)

Storage: 14 to 140 °F (–10 to 60 °C)

Operating: 20 to 80% RH, non-condensing

Storage: 10 to 90% RH, non-condensing

Up to 4,900 feet (1,500 m)

Up to 7,500 feet (2,286 m) with High

Altitude Mode enabled; see page 62

Safety and Approvals

United States FCC Part15B Class B (DoC)

UL60950-1

Canada ICES-003 Class B

CSA C22.2 No. 60950-1

Pixelworks ™ DNX ™ ICs are used in this projector.

Technical Specifications 107


Compatible Video Formats

You can use any of the following video sources: VCR, DVD player, camcorder, digital camera, or gaming console. The projector supports composite video, S-Video, component video, and RGB video, and it automatically senses the video format (HDTV, SDTV, NTSC, PAL, or SECAM).

The projector supports these international video standards:

Mode

NTSC

NTSC 4:3

PAL

M-PAL

N-PAL

PAL60

SECAM

TV525i

TV625i

SDTV (480p and 480i)

SDTV (576p and 576i)

HDTV720p

HDTV720p

HDTV1080i

HDTV1080i

60

50

60

50

60

50

60

50

Refresh Rate (Hz)

60

60

50

60

50

60

50

Compatible Computer Display Formats

You can connect the projector to a wide range of computers, including

PCs and notebooks, Apple Macintosh, PowerPC and Intel Core

Macintosh computers, PowerBook computers, many iMac and iBook series systems, and high-end workstations such as the Sun ®

SPARCstation.

™

Although images are displayed at the projector’s native resolution of

1280 × 800 pixels, Epson’s patented SizeWise chip supports computer display formats ranging from VGA through WSXGA+.

To project images output from a computer, the computer’s external monitor signal must be set at a refresh rate (vertical frequency) that’s compatible with the projector; see the following table for compatible formats. For best results, the computer’s resolution should be set to match the projector’s native resolution (1280 × 800). If this resolution isn’t available, select one of the other compatible formats:

■ Windows:

Right-click the desktop, select Properties , click the Settings tab, and select a compatible resolution. (For a notebook displaying through an external monitor port, you’ll need to click the

Advanced button on the Settings tab, then adjust the resolution of the external monitor.)

■ Macintosh OS X:

From the Apple menu, select System Preferences , then click

Displays . Make sure the VGA Display or Color LCD dialog box is selected, then click the Display tab and select a compatible resolution.

You may need to modify existing presentation files if you created them for a different resolution. See your software documentation for details.

Technical Specifications 109


The projector supports these monitor display formats:

Mode

VGA—60

VESA—72

VESA—75

VESA—85

SVGA—56

SVGA—60

SVGA—72

SVGA—75

SVGA—85

XGA—60

XGA—70

XGA—75

XGA—85

WXGA60-1

WXGA60-2

WXGA

WXGA+

WSXGA+60**

SXGA60 iMAC VGA iMAC SVGA iMAC XGA

MAC13

MAC16

MAC19

Refresh rate

(Hz)

60

72

75

85

56

60

72

75

85

60

70

75

85

60

60

60

75

85

60

75

85

60

60

117

95

75

67

75

75

Resolution

640 × 480 (640 × 360*)

640 × 480 (640 × 360*)

640 × 480 (640 × 360*)

640 × 480 (640 × 360*)

800 × 600 (800 × 450*)

800 × 600 (800 × 450*)

800 × 600 (800 × 450*)

800 × 600 (800 × 450*)

800 × 600 (800 × 450*)

1024 × 768 (1024 × 576*)

1024 × 768 (1024 × 576*)

1024 × 768 (1024 × 576*)

1024 × 768 (1024 × 576*)

1280 × 768

1360 × 768

1280 × 800

1280 × 800

1280 × 800

1440 × 900

1440 × 900

1440 × 900

1680 × 1050

1280 × 960

1280 × 1024

640 × 480 (640 × 360*)

800 × 600 (800 × 450*)

1024 × 768 (1024 × 576*)

640 × 480

832 × 624

1024 × 768

* Letterbox signal

** Available only when Resolution is set to Wide in the Signal menu.

B

Notices

T his chapter includes safety instructions and other important information about your PowerLite projector.

B

Important Safety Instructions

Follow these safety instructions when setting up and using the projector:

■

■

■

■

■

■

■

■

■

■

■

Do not place the projector on an unstable cart, stand, or table.

Do not use the projector near water or sources of heat.

Use the type of power source indicated on the projector. If you are not sure of the power available, consult your dealer or power company.

Place the projector near a wall outlet where the plug can be easily unplugged.

Insert the projector’s two-prong plug into a properly grounded outlet.

Do not hold the plug with wet hands.

Take the following precautions for the plug. Failure to comply with these precautions could result in sparks or fire: Do not insert the plug into an outlet with dust present. Insert the plug firmly into the outlet.

Do not overload wall outlets, extension cords, or integral convenience receptacles. This can cause fire or electric shock.

Do not place the projector where the cord can be walked on. This may result in fraying or damage to the plug.

Unplug the projector from the wall outlet before cleaning. Use a damp cloth for cleaning. Do not use liquid or aerosol cleaners.

Do not block the slots and openings in the projector case. They provide ventilation and prevent the projector from overheating. Do not operate the projector on a sofa, rug, or other soft surface, or in a closed-in cabinet unless proper ventilation is provided.

Never push objects of any kind through the cabinet slots. Never spill liquid of any kind into the projector.

111

112 Notices

■

■

■

■

■

■

■

■

■

Except as specifically explained in this User’s Guide, do not attempt to service this product yourself. Refer all servicing to qualified personnel.

Opening or removing covers may expose you to dangerous voltages and other hazards.

Unplug the projector from the wall outlet and refer servicing to qualified service personnel under the following conditions: When the power cord or plug is damaged or frayed. If liquid has been spilled into the projector, or if it has been exposed to rain or water. If it does not operate normally when you follow the operating instructions, or if it exhibits a distinct change in performance, indicating a need for service. If it has been dropped or the housing has been damaged.

The lamp(s) in this product contain mercury. Please consult your state and local regulations regarding disposal or recycling. Do not put in the trash.

Unplug the projector during lightning storms or when it will not be used for extended periods.

Do not place the projector and/or remote control on top of heat-producing equipment or in a hot location.

If you use the projector in a country other than where you purchased it, use the correct power cord for that country.

Do not stand on the projector or place heavy objects on it.

Do not use the projector outside of the required temperature range of

41 to 95 °F (5 to 35 °C). Doing so may cause an unstable display and could lead to projector damage.

Do not store the projector outside of the required temperature range of

14 to 140 °F ( − 10 to 60 °C) or in direct sunlight for long periods of time. Doing so may cause damage to the case.

WARNING: The cords included with this product contain chemicals, including lead, known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling. (provided in accordance

with Proposition 65 in Cal. Health & Safety Code § 25249.5 et seq).

FCC Compliance Statement

For United States Users

■

■

■

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio and television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

■

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for help.

WARNING

The connection of a non-shielded equipment interface cable to this equipment will invalidate the FCC Certification or Declaration of this device and may cause interference levels which exceed the limits established by the

FCC for this equipment. It is the responsibility of the user to obtain and use a shielded equipment interface cable with this device. If this equipment has more than one interface connector, do not leave cables connected to unused interfaces. Changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment.

For Canadian Users

This Class B digital apparatus meets all requirements of the Canadian

Interference-Causing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le materiel brouilleur du Canada.

Notices 113

114 Notices

Index

A

A/V cable, 26 to 27

A/V Mute, 48, 63, 67 to 68, 84, 89

Accessories, 13, 92

Adapter, Macintosh, 21

Air filter

cleaning and replacing, 74 to 76

purchasing, 13

Altitude, 63, 107

AMX Device Discovery setting, 97

Anti-theft device, 13

Aspect ratio, 50, 60, 105

Aspect setting, 60

Audio

adjusting volume, 43, 61

cable, 24, 89 connecting laptop, 24

problems, troubleshooting, 89

turning off, 48

Auto button, 43, 59

Auto Setup setting, 43, 59

B

Background Color setting, 63, 69

Banding in image, 88

Batteries, replacing, 51

Blackboard color mode, 47, 57

Blank screen, 38 to 39, 84 to 85

Blue background, 63

Blurry image, 87

Brightness, 76, 105

Brightness Control setting, 42, 84

Brightness setting, 42, 57, 84, 88

Browser, monitoring projector with, 103

Buttons, disabling projector, 61, 71

C

Cables, 10 to 13, 92

Camcorder, connecting to, 26 to 33

Carrying case, optional, 80

Ceiling

mount, 13, 19

projection, 19, 63

Cleaning

air filter and vents, 74 to 76

lens, 74 projector case, 74

Closed Caption setting, 62

Color

adjusting, 47, 56 to 58

problems, 88

specifications, 105

Color Adjustment setting, 58

Color Mode, 47, 57

Color Saturation setting, 57

Component-to-VGA video cable, 12 to 13, 26,

30

Composite video cable, 26 to 27

Computer

cable, 10, 20 to 22

connecting to projector, 20 to 24

source, selecting, 21, 22, 38, 46, 59

support, 7

supported display formats, 109 to 110

Computer/Component Video ports, 21 to 22,

29, 46

Connecting projector

to a computer, 20 to 24

to a game console, 26 to 33

to a video source, 26 to 33

to external monitor, 23

to speakers, 25, 33

Contrast, 105

Contrast setting, 57, 88

Control Panel Lock setting, 61, 71

115

D

Default password, 66

Default settings, restoring, 72

Digital camera, connecting to, 26 to 33

Dimensions, 106

Direct Power On setting, 63

Distance from projector to screen, 16, 105

Documentation, using, 9

DVD player, connecting to, 26 to 33

E

E-mail alerts, 97 to 98, 102

EMP Monitor

monitoring the projector, 98 to 102

problems, 91

using, 98 to 102

Entering the password, 70

Environmental specifications, 107

Epson

accessories, 13, 92

Extra Care Road Service, 10

PrivateLine Support, 9, 92

Store, 92

technical support, 9, 91 to 92

Ethernet connection, 95

Extended menu, 54, 62 to 63

External monitor, connecting, 23

Extra Care Road Service, 10

E-Zoom button, 49

F

FCC compliance statement, 113

Filter, cleaning and replacing, 74 to 76

Focusing, 40

Foot release lever, 41

Freeze button, 48

Front projection, 16 to 18, 63

Front/Ceiling setting, 19, 63

Full Lock setting, 61, 71

G

Game color mode, 47, 57

Game console, connecting to, 26 to 33

H

Height of image, adjusting, 41

Help, 9, 91 to 92

Help system, using, 82

High Altitude Mode setting, 63, 107

High brightness, 42, 76, 84, 105

I

iBook, connecting to, 20 to 21

iMac, connecting to, 12, 20 to 22

Image

capturing and saving in projector, 67 to 68

correcting shape of, 42, 60, 86 fitting on screen, 43, 59, 60, 86

focusing, 40

freezing, 48

height, adjusting, 41

menu, 54, 56 to 58

positioning, 41, 43, 59

problems, 84 to 88

raising, 41

selecting source, 21, 22, 27, 37, 38, 46,

59 to 60 shape, correcting, 42, 60, 86

size and projection distance, 16, 105

turning off, 48

zooming, 49

Info menu, 54, 64 to 65

Input signal, selecting, 21, 22, 27 to 30, 38,

46, 59 to 60

Installing software, 94

Instant Off feature, 44

K

Kensington anti-theft device, 13

Keystone correction, 42, 60, 86, 106

116 Index

L

Lamp

automatic shutoff, 44

brightness, 76, 84, 105

number of hours used, 64, 76, 79, 106

replacing, 76 to 79

specifications, 106

status light, 82 to 83

timer, resetting, 79

Language setting, 63

Laptop computer

connecting to, 20 to 22

displaying on, 38 to 39, 85

LCD panels, 7

Lens

cleaning, 74

specifications, 105

Lights, status, 82 to 83

Logo

creating, 67 to 68

displaying, 68 to 69 turning on, 63, 69

Low brightness, 42, 76, 105

M

Macintosh

adapter, 21

connecting, 20 to 22

Manuals, 9

Menus

changing settings, 55 to 56

Extended, 54, 62 to 63

Image, 54, 56 to 58

Info, 54, 64 to 65

Network, 54, 64, 96 to 98

Reset, 54, 72

Settings, 54, 60 to 61

Signal, 54, 58 to 60

User’s Logo, 67 to 68

using, 54 to 56

Messages setting, 62

Monitor, external, 23

Monitoring projector

e-mail notifications, 97 to 98, 102

EMP Monitor, 98 to 102

with browser, 103

Moving projector, 80

N

Network

connecting to, 95

managing projector remotely, 93 to 103

menu, 54, 64, 96 to 98

problems, 91

settings, 64, 96 to 98, 99

system requirements, 94

Network Protect password, 69

Noise level, 106

O

Options for projector, 13, 92

P

Password

default, 66

entering, 70 logo protection, 67 to 70

Network Protect, 69

problems, 89

prompt, 37, 70

request code, 70

setting, 68 to 69

turning on, 69

Photo color mode, 47, 57

Picture source, selecting, 21, 22, 27 to 30, 38,

59 to 60

Pixelworks, 107

Position setting, 59

Positioning

image, 41, 59

projector, 16 to 19

Index 117

Power

button, 37, 44

consumption, 106

light, 36, 82 to 83

supply, 106

PowerBook, connecting to, 20 to 22

Presentation color mode, 47, 57

Presenters Online, 9

PrivateLine Support, 9, 92

Problems

color, 88 image, 84 to 88

monitoring projector, 91 network, 91

password, 89

remote control, 90

sound, 89

Projection lamp, see Lamp

Projector

accessories, 13, 92

carrying case, optional, 80

cleaning, 73 to 76

disabling buttons, 61, 71

distance from screen, 16, 105

foot, adjusting height with, 41

lamp specifications, 106

monitoring remotely, 93 to 103

password protection, 66 to 70

positioning, 18 to 19

resolution, 7, 105, 109 to 110

transporting, 80

turning off, 44

turning on, 36 to 37

unpacking, 10

viewing information about, 64 to 65

Q

Quick Setup sheet, 9

R

Raising image, 41

RCA A/V cable, 26 to 27

Rear projection, 19, 63

Registration, 10

Remote control

problems, 90 receivers, disabling, 61, 84, 90

replacing, 13, 92

replacing batteries, 51

specifications, 106

using, 45 to 51

Remote Receiver setting, 61, 84, 90

Replacing

air filter, 74 to 76

lamp, 76 to 79

remote control, 13, 92

remote control batteries, 51

Request code, password, 70

Reset menu, 54, 72

Resolution, 7, 65, 105, 109 to 110

S

Safety

approvals, 107

instructions, 111 to 112

Screen logo, see User’s Logo

Screen, distance from projector, 16, 105

Screens, portable, 13

Setting a password, 68 to 69

Settings menu, 54, 60 to 61

Sharpness setting, 58

Signal menu, 54, 58 to 60

Sleep mode, 44, 63

Software installation, 94

Sound, see Audio

Source Search button, 21 to 22, 27 to 30,

37 to 38, 46

Speaker, specifications, 105

Speakers, connecting external, 25, 33

Specifications, technical, 105 to 110

Sports color mode, 47 sRGB color mode, 47, 57

118 Index

Standby Mode setting, 63, 99

Startup screen

creating, 67 to 68

displaying, 68 to 69

user’s logo, see User’s Logo

Startup Screen setting, 63

Status lights, 82 to 83

Stopping action, 48

Stripes in image, 88

Support, 9, 91 to 92

S-Video cable, 12, 13, 26

Switching picture source, 38, 46

Sync, adjusting, 59, 87 to 88

System requirements, network, 94

T

Technical support, 9, 91 to 92

Temperature

light, 82 to 83

requirements, 107

Test Pattern setting, 61

Text color mode, 47

Theatre color mode, 47, 57

Timer, lamp, 79

Tint setting, 58

Tracking, adjusting, 59, 87 to 88

Transporting projector, 80

Troubleshooting

color, 88

cut-off image, 43, 86

image quality, 87 to 88

image shape, 86

network problems, 91

no image, 84 to 85

no sound, 89 password, 89

remote control problems, 90

Turning off

audio, 48 picture, 48

projector, 44

Turning on

password, 69

projector, 36 to 37

User’s Logo, 63, 69

Typing the password, 70

U

Unpacking projector, 10

User’s Logo

creating, 67 to 68

displaying, 68 to 69

turning on, 63, 69

V

VCR, connecting to, 26

VGA computer cables, 10, 20 to 22

Video

display settings, 64 to 65

formats, supported, 7, 108

source, connecting to, 26 to 33

source, selecting, 27, 37 to 38, 46, 59 to 60

Video Signal setting, 60

Volume, adjusting, 43, 61

W

Warning lights, 82 to 83

Warranty, 10

Weight, 106

Z

Zoom ratio, 105

Zoom setting, 60

Zooming image, 49

Index 119

Epson PowerLite 400W User's Guide

Assistant Bot

PowerLite

400W

Multimedia Projector

User’s Guide

Important Safety Information

Copyright Notice

Trademarks

Contents

Welcome

Getting the Most from Your Projector

Using Your Documentation

Getting More Information

Registration and Warranty

Unpacking the Projector

Projector Parts

Additional Components

Optional Accessories

Setting Up the Projector

Positioning the Projector

Whiteboard Installation

Other Installations

Connecting to a Computer

Connecting with the VGA Cable

Connecting with a VGA-5BNC Cable

Connecting an External Monitor

Playing Sound Through the Projector

Connecting External Speakers

Connecting to Video Sources

Connecting a Composite Video Source

Connecting an S-Video Source

Connecting an RGB Video Source

Connecting a Component Video Source

Playing Sound Through the Projector

For RCA-Type Audio Output Ports

For Stereo Mini-Jack Audio Output Ports

Connecting External Speakers

Projecting

Turning On Your Equipment

Turning On the Projector

Selecting the Image Source

What To Do If You See a Blank Screen

If you’re using a PC laptop:

If you’re using a Macintosh laptop with OS X:

Adjusting the Image

Focusing and Zooming Your Image

Adjusting the Height of Your Image

Adjusting the Image Shape

Adjusting the Brightness

Correcting Computer Images

Adjusting the Volume

Shutting Down the Projector

Using the Remote Control

Controlling the Picture and Sound

Switching Between Picture Sources

Adjusting the Color Mode

Turning Off the Picture and Sound

Stopping Action

Zooming Your Image

Changing the Image’s Aspect Ratio

Replacing the Batteries

Fine-tuning the Projector

Using the Projector’s Menu System

Changing Menu Settings

Adjusting Colors and Clarity

Adjusting the Input Signal

Customizing Projector Features

Selecting Projector Setup Options

Selecting Network Settings

Viewing Lamp Usage and Other

Information

Using the Projector’s Security Features

Creating Your Own Screen Logo

Setting a Password

Turning On the Password and User’s Logo

Starting the Projector with a Password

Disabling the Projector’s Buttons

Installing Security Locks

Restoring the Default Settings