W-3 | User manual | Maytag – Washer – Atlantis III – Supplement – 16009485-03
Add to my manuals4 Pages
advertisement
Attached is Supplement three for service manual 16009485. This Maytag Washer
Service Manual supplement covers Atlantis III Models. We suggest you file this with your 16009485 Manual for reference.
SECTION 1. Product Definition .............................................................................. 2
SECTION 2. Console ............................................................................................ 2
SECTION 3. Automatic Temperature Control ......................................................... 3
SECTION 4. Water Valves ..................................................................................... 3
SECTION 5. Front Removal ................................................................................... 4
SECTION 6. Pump Assembly ................................................................................ 4
SECTION 7. Tub Seal and Bearing ........................................................................ 4
To locate an authorized servicer, please consult your telephone book or the dealer from
whom you purchased this product. For further assistance, please contact:
Customer Service Support Center
CAIR Center
Web Site Telephone Number
WWW.AMANA.COM ................................................ 1-800-843-0304
WWW.JENNAIR.COM ............................................. 1-800-536-6247
WWW.MAYTAG.COM ............................................. 1-800-688-9900
CAIR Center in Canada ........................................... 1-800-688-2002
Amana Canada Product ........................................... 1-866-587-2002
©2002 Maytag Appliances Company
16009485-03 Rev. 0 1
Section 1. Product Definition:
The Atlantis III is similar to previous Atlantis washer models, with the following exceptions:
• T he Control Wire Harness has a connector which allows removal of the entire Console
Assembly from the cabinet.
• A new non-serviceable water pump.
• Automatic Temperature Control. The incoming water temperature is controlled by 2 thermostats attached to the Injector Assembly.
Section 2. Console
Disassembly and Testing
The Console Assembly has been designed to allow full removal of the console from the cabinet via a plug added to the wiring harness. This feature will also aid in performing diagnostic tests to the various components.
Centrifugal Switch
Attach Ohm Meter leads to BK 32 and OR 31 .5 ohms.
Overload
Attach Ohm Meter leads to WH 9 and YL M .5 ohms.
Water Valves
Hot
Attach Ohm Meter leads to OR 13 and BR 15 1 ohm.
Cold
M
Y
L
37
53
W
H
G
Y
32
B
K
B
R 31
O
R
9 W
H
51
P
U
K
B
32
13
O
R
22
R
D
15
B
R
U
B
11
Motor Resistance
Main Winding
Attach Ohm Meter leads to WH 9 and BK 32 2 ohms.
Start Winding
Attach Ohm Meter leads to BR 21 and RD 22 4 ohms.
Lower harness shown from wire insertion side
2 16009485-03 Rev. 0
©2002 Maytag Appliances Company
Section 3. Automatic
Temperature Control
ATC Functionary
The nozzle of the water valve directs the incoming water over two thermostats mounted onto the upper injector assembly. One of the thermostats controls the cold water valve, and the other controls the hot water valve.
When ATC cold wash is selected:
The cold water valve is opened for full cold fill. If the incoming water temperature is below approximately
65°F, the hot water valve will open and warm the incoming water. The hot water valve will continue to cycle on and off maintaining optimum cold water temperature until the tub is full. The target water temperature for a cold wash is 70°F to 80°F.
When ATC warm wash is selected:
The hot water valve is opened for full hot fill. If the incoming water temperature is above approximately
100°F, the cold water valve will open and cool the incoming water. The cold water valve will continue to cycle on and off maintaining optimum warm water temperature until the tub is full. The target water temperature for a warm wash is 90°F to 100°F.
ATC is not active during rinse or hot wash.
Section 4. Water Valves
Water Valve Access
Water valve access is gained by lifting the top assembly. The water valve is located just behind the Automatic Temperature Control Assembly and mounted to the back cabinet wall. To remove the water valve.
Disconnect water lines and remove one screw on the left side of the water valve mounting bracket. Slide bracket to the left and remove.
©2002 Maytag Appliances Company
16009485-03 Rev. 0 3
Section 5. Front Removal
Procedure
Lift Top Assembly by releasing spring clips between top and front panel. Use a plastic putty knife to disengage clip. Lift top and remove top screws through the back of the Front Panel. There are two spring clips a screws one each side.
Section 7. Tub Seal and
Bearing
The Allantis III Seal and Bearing are unique and are matched to the duel drive high torque transmission, used on this washer. When replacing the seal and bearing, order parts specific to the Atlantis III washer.
The seal and bearing used on older models will not fuction properly. The seal kit will also be supplied with the replacement transmission assembly if it is necessary to install a new one.
Section 6. Pump Assembly
Atlantis washers use a new pump assembly which will be totally replaced should it require repair. A pump kit will be available containing the entire pump assembly.
Triple Seal
4 16009485-03 Rev. 0
©2002 Maytag Appliances Company
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project