MSI EC14H Operating instructions

MSI EC14H Operating instructions
Issue Date:
2003-09-25
Page 1 of 1
Report Reference #
E203413-A17-CB-1
COVER PAGE FOR TEST REPORT
Test Item Description:
Model/Type Reference:
Home Plug Device
MS-6821
Rating(s):
100 - 240 Vac, 47 - 63 Hz, 0.1 A.
Standards:
IEC60950, Third Edition (1999)
Applicant Name and Address: MICRO-STAR INTERNATIONAL CO LTD
69 LI-DE ST
CHUNG HO CITY
TAIPEI HSIEN TAIWAN
Factory Location(s):
1. MICRO-STAR INTERNATIONAL CO., LTD.
488 BAN NAN ST. CHUNG HO CITY
TAIPEI HSIEN 235 TAIWAN
2. MSI COMPUTER (SHENZHEN) CO., LTD.
LONGMA INFORMATION TECHNOLOGY IND. PARK
TANGTOU VILLAGE, SHIYAN TOWN BAO'AN DISTRICT
SHENZHEN GUANGDONG CHINA
This Report includes the following parts, in addition to this cover page:
1. Specific Technical Criteria
2. Clause Verdicts
3. Critical Components
4. Test Results
5. National Differences
6. Enclosures
All applicable tests according to the above standard(s) have been carried out.
Test results are valid only for the tested equipment.
This Test Report can be reproduced only in whole.
Amendments and corrections can be reproduced only with the original CB Test Report.
Written permission from UL International Demko A/S is required if the test report is copied in part.
Copyright © 2002 UL International Demko A/S
UL International Demko A/S
Issue Date:
2003-09-25
TRF No.: 1950__F
Page 1 of 42
Report Reference #
UL International Demko A/S
E203413-A17-CB-1
TRF originator: FIMKO
Issue Date:
2003-09-25
Page 2 of 42
Report Reference #
E203413-A17-CB-1
Particulars: test item vs. test requirements
Equipment mobility.................................................: direct plug-in
Operating condition................................................: continuous
Mains supply tolerance (%).....................................: +6%, -10%
Test for IT power systems.......................................: No
IT testing, phase-phase voltage (V) ........................: N/A
Class of equipment ................................................: Class II (double insulated)
Mass of equipment (kg) ..........................................: 0.13 kg
Protection against ingress of water..........................: IP 20
Possible test case verdicts:
- test case does not apply to the test object .............: N / A
- test object does meet the requirement ..................: P(Pass)
- test object does not meet the requirement ............: F(Fail)
Gene ral remarks:
This report is not valid as a CB Test Report unless signed by an approved CB Testing Laboratory and
appended to a CB Test Certificate issued by a NCB in accordance with IECEE 02.
The test results presented in this report relate only to the object tested.
This report shall not be reproduced, except in full, without the written approval of the Issuing testing
laboratory.
"(see Enclosure #)" refers to additional information appended to the report.
"(see appended table)" refers to a table appended to the report.
Throughout this report a point is used as the decimal separator.
TRF No.: 1950__F
UL International Demko A/S
TRF originator: FIMKO
Issue Date:
2003-09-25
Page 3 of 42
Report Reference #
E203413-A17-CB-1
General Product Information:
Report Summary
All applicable tests according to the referenced standard(s) have been carried out.
Product Description
Electronic Component mounted on PWB and housed with plastic enclosure.
Model Differences
N/A
Additional Information
N/A
Engineering Consideration
The product was submitted and tested for use at the
manufacturer's recommended ambient temperature
(Tmra) of:
40 degree C,
The power supply means are
Direct plug-in, Pluggable A
The product is intended for use on the following
systems
TN
The equipment disconnect device is considered to be
Plug
Engineering Conditions of Acceptability
When installed in an end-product, consideration must be given to the following:
TRF No.: 1950__F
UL International Demko A/S
TRF originator: FIMKO
Issue Date:
2003-09-25
Page 5 of 42
Report Reference #
E203413-A17-CB-1
IEC 60950
Clause
Requirement + Test
Result - Remark
Verdict
1
GENERAL
Pass
1.5
Components
Pass
1.5.1
Comply with IEC 950 or relevant component
standard
(see appended table 1.5.1)
Pass
1.5.2
Evaluation and testing of components
Certified components are used
in accordance with their
ratings, certifications and they
comply with applicable parts of
this Standard.
Pass
Components not certified are
used in accordance with their
ratings and they comply
IEC60950 and the relevant
component Standard.
Components, for which no
relevant IEC Standard exist,
have been tested under the
condition occurring in the
equipment, using applicable
parts of IEC60950.
Dimensions (mm) of mains plug for direct plug-in .: The blade configuration is in
accordance with the national
applicable standards.
Pass
Torque and pull test of mains plug for direct plug-in; Refer to 4.3.6.
torque (Nm); pull (N)...........................................:
Pass
1.5.3
Thermal controls
1.5.4
Transformers
See Annex C-Transformers.
Pass
1.5.5
Interconnecting cables
Interconnecting cables comply
with the relevant requirements
of this standard.
Pass
1.5.6
Capacitors in primary circuits ..............................:
N/A
1.5.7
Double or reinforced insulation bridged by
components
N/A
1.5.7.1
Bridging capacitors
N/A
1.5.7.2
Bridging resistors
N/A
1.5.7.3
Accessible parts
N/A
1.5.8
Components in equipment for IT power systems
N/A
TRF No.: 1950__F
N/A
UL International Demko A/S
TRF originator: FIMKO
Issue Date:
2003-09-25
Page 6 of 42
Report Reference #
E203413-A17-CB-1
IEC 60950
Clause
Requirement + Test
Result - Remark
Verdict
1.6
Power Interface
1.6.1
AC power distribution systems
AC power distribution systems
are classify as TN.
Pass
1.6.2
Input current
The steady state input current
of the equipment did not
exceed the RATED CURRENT
by more than 10% under
NORMAL LOAD.
Pass
Pass
(see appended table 1.6.2)
1.6.3
Voltage limit of hand-held equipment
Not hand-held equipment.
1.6.4
Neutral conductor
Class II equipment. Phase
conductors separated to body
by reinforced insulation.
TRF No.: 1950__F
UL International Demko A/S
N/A
Pass
TRF originator: FIMKO
Issue Date:
2003-09-25
Page 7 of 42
Report Reference #
E203413-A17-CB-1
IEC 60950
Clause
Requirement + Test
Result - Remark
1.7
Marking and Instructions
1.7.1
Power rating
Verdict
Pass
Rating marking readily visible
to operator.
See below for details.
Rated voltage(s) or voltage range(s) (V) ..............: 100 - 240 Vac
Pass
Pass
Symbol for nature of supply for d.c. .....................: AC Source
N/A
Rated frequency or frequency range (Hz).............: 47 - 63 Hz
Pass
Rated current (A)................................................: 100 mA
Pass
Manufacturer's name/Trademark .........................: MICRO-STAR
INTERNATIONAL CO., LTD. /
MSI
Pass
Type/model........................................................: Home Plug Device / See
Cover Page
Pass
Symbol of Class II ..............................................: 60417-1-IEC-5172 symbol
marked.
Pass
Other symbols ....................................................: Additional symbols may be
provided when submitted for
National Approval.
N/A
Certification marks..............................................: UL, C-UL
Pass
1.7.2
Safety instructions
Safety instructions in English.
Other languages will be
provided when submitted for
national approval.
Pass
1.7.3
Short duty cycles
The equipment is intended for
continuous operation.
N/A
1.7.4
Supply voltage adjustment ..................................:
N/A
1.7.5
Power outlets on the equipment ..........................:
N/A
1.7.6
Fuse identification..............................................: Evaluated as part of power
supply.
N/A
1.7.7
Wiring terminals
N/A
1.7.7.1
Protective earthing and bonding terminals
N/A
1.7.7.2
Terminal for a.c. mains supply conductors
1.7.8
Controls and indicators
Pass
1.7.8.1
Identification, location and marking......................: No indicators, switches and
other controls affecting safety
provided.
Pass
TRF No.: 1950__F
Direct plug in equipment.
UL International Demko A/S
N/A
TRF originator: FIMKO
Issue Date:
2003-09-25
Page 8 of 42
Report Reference #
E203413-A17-CB-1
IEC 60950
Clause
Requirement + Test
Result - Remark
Verdict
1.7.8.2
Colours..............................................................: No indicators, switches and
other controls affecting safety
provided.
1.7.8.3
Symbols according to IEC 60417.........................:
N/A
1.7.8.4
Markings using figures ........................................:
N/A
1.7.9
Isolation of multiple power sources ......................:
N/A
1.7.10
IT power system
1.7.11
Thermostats and other regulating devices
1.7.12
Language ..........................................................: Reviewed only English
markings/instructions.
Not intended for use on IT
power systems.
Pass
N/A
N/A
-
May be provided in other
languages when the
equipment will be applied for
other national certificated.
1.7.13
Durability
1.7.14
Removable parts
1.7.15
Replaceable batteries
The marking(s) withstood the
required test.
Pass
Pass
N/A
Language ..........................................................:
-
1.7.16
Operator access with a tool.................................: No operator access areas
require the use of a tool.
N/A
1.7.17
Equipment for restricted access locations ............: Equipment not intended for
installation in a RESTRICTED
ACCESS LOCATION.
N/A
2
PROTECTION FROM HAZARDS
TRF No.: 1950__F
UL International Demko A/S
Pass
TRF originator: FIMKO
Issue Date:
2003-09-25
Page 9 of 42
Report Reference #
E203413-A17-CB-1
IEC 60950
Clause
Requirement + Test
Result - Remark
Verdict
2.1
Protection from electric shock and energy hazards
Pass
2.1.1
Protection in OPERATOR access areas
Pass
2.1.1.1
Access to energized parts
No operator access to
energized parts.
Pass
Test by inspection ..............................................: No operator access to
energized parts.
Pass
Test with test finger ............................................: The test finger was unable to
contact bare hazardous parts,
basic insulation, or ELV
circuits.
Pass
Test with test pin ................................................: The test pin was unable to
contact bare hazardous parts.
Pass
Test with test probe ............................................: No TNV present.
N/A
2.1.1.2
Battery compartments.........................................:
N/A
2.1.1.3
Access to ELV wiring
Internal wiring in an ELV circuit
is not user accessible.
Working voltage (V); distance (mm) through
insulation ...........................................................:
N/A
-
2.1.1.4
Access to hazardous voltage circuit wiring
N/A
2.1.1.5
Energy hazards ..................................................: The hazardous energy circuits
can't be bridged by the test
finger in a straight position.
2.1.1.6
Manual controls
N/A
2.1.1.7
Discharge of capacitors in the primary circuit
N/A
Time-constant (s); measured voltage (V).............:
Pass
-
2.1.2
Protection in service access areas
No bare parts operating at
HAZARDOUS VOLTAGES in
a service access area.
N/A
2.1.3
Protection in restricted access locations
The unit is not intended to be
used in restricted locations.
N/A
TRF No.: 1950__F
UL International Demko A/S
TRF originator: FIMKO
Issue Date:
2003-09-25
Page 10 of 42
Report Reference #
E203413-A17-CB-1
IEC 60950
Clause
Requirement + Test
2.2
SELV Circuits
2.2.1
General requirements
2.2.2
Voltages under normal conditions (V) ..................: All accessible voltages are
less than 42.4 Vp or 60 V dc
and are classified as SELV.
Pass
2.2.3
Voltages under fault conditions (V)......................: Under fault conditions voltages
never exceed 71V peak and
120Vdc and do not exceed
42.4V peak or 60V dc for more
than 0.2 sec.
Pass
2.2.3.1
Separation by double or reinforced insulation
(method 1)
Pass
2.2.3.2
Separation by earthed screen (method 2)
N/A
2.2.3.3
Protection by earthing of the SELV circuit (method
3)
N/A
2.2.4
Connection of SELV circuits to other circuits ........: SELV circuit and all
interconnected circuits
separated from primary by
Double/Reinforced insulation.
The SELV circuit does not
exceed the SELV limits under
normal and fault conditions.
2.3
TNV Circuits
N/A
2.3.1
Limits
N/A
2.3.2
2.3.3
Result - Remark
Pass
SELV levels are maintained
after single fault condition.
Pass
-
Separation from other circuits and from accessible
parts
N/A
Insulation employed ...........................................:
-
Separation from hazardous voltages
Connection of TNV circuits to other circuits
Insulation employed ...........................................:
2.3.5
Pass
Type of TNV circuits ...........................................:
Insulation employed ...........................................:
2.3.4
Verdict
Test for operating voltages generated externally
TRF No.: 1950__F
UL International Demko A/S
N/A
N/A
N/A
TRF originator: FIMKO
Issue Date:
2003-09-25
Page 11 of 42
Report Reference #
E203413-A17-CB-1
IEC 60950
Clause
Requirement + Test
Result - Remark
Verdict
2.4
Limited Current Circuits
N/A
2.4.1
General requirements
N/A
2.4.2
Limit values
N/A
Frequency (Hz) ..................................................:
-
Measured current (mA).......................................:
-
Measured voltage (V).........................................:
-
Measured capacitance (µF) ................................:
-
2.4.3
Connection of limited current circuits to other
circuits
N/A
2.5
Limited Power Sources
N/A
Inherently limited output
N/A
Impedance limited output
N/A
Overcurrent protective device limited output
N/A
Regulating network limited output under normal
operating and single fault condition
N/A
Regulating network limited output under normal
operating conditions and overcurrent protective
device limited output under single fault condition
N/A
Output voltage (V), output current (A), apparent
power (VA) ........................................................:
-
Current rating of overcurrent protective device (A):
-
TRF No.: 1950__F
UL International Demko A/S
TRF originator: FIMKO
Issue Date:
2003-09-25
Page 12 of 42
Report Reference #
E203413-A17-CB-1
IEC 60950
Clause
Requirement + Test
Result - Remark
2.6
Provisions for Earthing and Bonding
N/A
2.6.1
Protective earthing
N/A
2.6.2
Functional earthing
N/A
2.6.3
Protective earthing and protective bonding
conductors
N/A
2.6.3.1
Size of protective earthing conductors
N/A
Rated current (A), cross-sectional area (mm²),
AWG .................................................................:
2.6.3.2
Size of protective bonding conductors
Verdict
N/A
Rated current (A), cross-sectional area (mm²),
AWG .................................................................:
-
Rated current (A), type and nominal thread
diameter (mm) ...................................................:
N/A
Resistance (Ohm) of earthing conductors and their
terminations, test current (A) ...............................:
N/A
2.6.3.4
Colour of insulation................................ .............:
N/A
2.6.4
Terminals
N/A
2.6.4.1
Protective earthing and bonding terminals
N/A
2.6.3.3
Rated current (A), type and nominal thread
diameter (mm) ...................................................:
-
2.6.4.2
Separation of the protective earthing conductor
from protective bonding conductors
N/A
2.6.5
Integrity of protective earthing
N/A
2.6.5.1
Interconnection of equipment
N/A
2.6.5.2
Components in protective earthing conductors and
protective bonding conductors
N/A
2.6.5.3
Disconnection of protective earth
N/A
2.6.5.4
Parts that can be removed by an operator
N/A
2.6.5.5
Parts removed during servicing
N/A
2.6.5.6
Corrosion resistance
N/A
2.6.5.7
Screws for protective bonding
N/A
2.6.5.8
Reliance on telecommunication network
N/A
TRF No.: 1950__F
UL International Demko A/S
TRF originator: FIMKO
Issue Date:
2003-09-25
Page 13 of 42
Report Reference #
E203413-A17-CB-1
IEC 60950
Clause
Requirement + Test
Result - Remark
Verdict
2.7
Overcurrent and Earth Fault Protection in Primary Circuits
Pass
2.7.1
Basic requirements
Pass
The building installation is
considered as protection in
Primary Circuits.
Instructions when protection relies on building
installation
Pass
2.7.2
Faults not covered in 5.3
Pass
2.7.3
Short-circuit backup protection
The building installation is
considered as providing shortcircuit protection.
Pass
2.7.4
Number and location of protective devices ...........: The building installation is
considered as providing shortcircuit protection.
N/A
2.7.5
Protection by several devices
N/A
2.7.6
Warning to service personnel..............................:
N/A
2.8
Safety Interlocks
N/A
2.8.1
General principles
N/A
2.8.2
Protection requirements
N/A
2.8.3
Inadvertent reactivation
N/A
2.8.4
Fail-safe operation
N/A
2.8.5
Interlocks with moving parts
N/A
2.8.6
Overriding an interlock
N/A
2.8.7
Switches and relays in interlock systems
N/A
2.8.7.1
Contact gaps (mm) ................................ .............:
N/A
2.8.7.2
Overload test
N/A
2.8.7.3
Endurance test
N/A
2.8.7.4
Electric strength test (V)
N/A
2.8.8
Mechanical actuators
N/A
TRF No.: 1950__F
UL International Demko A/S
TRF originator: FIMKO
Issue Date:
2003-09-25
Page 14 of 42
Report Reference #
E203413-A17-CB-1
IEC 60950
Clause
Requirement + Test
Result - Remark
Verdict
2.9
Electrical Insulation
2.9.1
Properties of insulating materials
See appended table 1.5.1
Pass
2.9.2
Humidity conditioning
Humidity treatment performed
to 48 hrs in condition:
Pass
Pass
93%, 25 Degree C
2.9.3
Requirements for insulation
Electric strength test
conducted after the humidity
treatment. No flash over or
breakdown of insulation.
Pass
(see sub-clause 2.10, 4.5.1,
and 5.2 )
2.9.4
Insulation parameters
Both parameters were
considered.
Pass
2.9.5
Categories of insulation
Reinforce insulation required
for Primary and SELV. For
functional insulation, see 5.3.4.
Pass
TRF No.: 1950__F
UL International Demko A/S
TRF originator: FIMKO
Issue Date:
2003-09-25
Page 15 of 42
Report Reference #
E203413-A17-CB-1
IEC 60950
Clause
Requirement + Test
Result - Remark
Verdict
2.10
Clearances, Creepage Distancesand Distances Through Insulation
Pass
2.10.1
General
Pollution degree 2 applicable.
Pass
2.10.2
Determination of working voltage
(see appended table 2.10.3
and 2.10.4)
Pass
2.10.3
Clearances
(see appended table 2.10.3
and 2.10.4)
For Functional Insulat ion, see
5.3.4.
Pass
2.10.3.1
General
2.10.3.2
Clearances in primary circuit
(see appended table 2.10.3
and 2.10.4)
Pass
2.10.3.3
Clearances in secondary circuits
Functional insulation only. See
5.3.4 .
Pass
2.10.3.4
Measurement of transient levels
2.10.4
Creepage distances
Pass
N/A
(see appended table 2.10.3
and 2.10.4)
For Functional Insulation, see
5.3.4.
CTI tests ............................................................: Assume material group III b:
100<=CTI<175
Pass
-
2.10.5
Solid insulation
See below
Pass
2.10.5.1
Minimum distance through insulation
(see appended table 2.10.5)
Pass
2.10.5.2
Thin sheet material
Evaluated as part of power
supply.
Pass
2.10.5.3
2.10.5.4
Number of layers (pcs) .......................................:
-
Electric strength test...........................................:
-
Printed boards
N/A
Distance through insulation
N/A
Electric strength test for thin sheet insulating
material ................................ .............................:
-
Number of layers (pcs) .......................................:
N/A
Wound components
Wire that has multi-layer
extruded or spirally wrapped
insulation (where only the
finished wire can be tested)
and passes the tests of annex
U.
Number of layers (pcs) .......................................: 3 layers
TRF No.: 1950__F
UL International Demko A/S
Pass
Pass
TRF originator: FIMKO
Issue Date:
2003-09-25
Page 16 of 42
Report Reference #
E203413-A17-CB-1
IEC 60950
Clause
Requirement + Test
Result - Remark
Verdict
Two wires in contact inside component; angle
between 45° and 90°
Prevented by insulating
sleeving
Pass
2.10.6
Coated printed boards
No coated printed wiring
boards.
N/A
2.10.6.1
General
N/A
2.10.6.2
Sample preparation and preliminary inspection
N/A
2.10.6.3
Thermal cycling
N/A
2.10.6.4
Thermal ageing (°C) ...........................................:
N/A
2.10.6.5
Electric strength test...........................................:
-
2.10.6.6
Abrasion resistance test
N/A
Electric strength test...........................................:
2.10.7
2.10.8
-
Enclosed and sealed parts..................................: No hermetically sealed or
enclosed components used.
N/A
Temperature T1=T2 + Tmra - Tamb +10K (°C) .....:
N/A
Spacings filled by insulating compound................:
N/A
Electric strength test...........................................:
-
2.10.9
Component external terminations
N/A
2.10.10
Insulation with varying dimensions
N/A
3
WIRING, CONNECTIONS AND SUPPLY
TRF No.: 1950__F
UL International Demko A/S
Pass
TRF originator: FIMKO
Issue Date:
2003-09-25
Page 17 of 42
Report Reference #
E203413-A17-CB-1
IEC 60950
Clause
Requirement + Test
3.1
General
Pass
3.1.1
Current rating and overcurrent protection
Pass
3.1.2
Protection against mechanical damage
The wires are routed away
from sharp edges and parts
which could damage
insulation.
Pass
3.1.3
Securing of internal wiring
The wires are positioned in
such a manner that prevents
excessive strain, loosening of
terminal connections and
damage of conductor
insulation.
Pass
3.1.4
Insulation of conductors
Insulation on internal
conductors is considered to be
of adequate quality and
suitable for the application and
the working voltages involved.
All internal wirings are UL
Recognized and rated
minimum 300 V ac.
Pass
3.1.5
Beads and ceramic insulators
N/A
3.1.6
Screws for electrical contact pressure
N/A
3.1.7
Non -metallic materials in electrical connections
3.1.8
Self-tapping and spaced thread screws
N/A
3.1.9
Termination of conductors
N/A
10 N pull test
N/A
3.1.10
Sleeving on wiring
TRF No.: 1950__F
Result - Remark
Verdict
No contact pressure through
insulating material.
Not provided.
UL International Demko A/S
Pass
N/A
TRF originator: FIMKO
Issue Date:
2003-09-25
Page 18 of 42
Report Reference #
E203413-A17-CB-1
IEC 60950
Clause
Requirement + Test
Result - Remark
Verdict
3.2
Connection to A.C. Mains Supplies
Pass
3.2.1
Means of connection ..........................................: The unit is provided with a
means for direct plug-in.
Pass
3.2.2
Multiple supply connections
Single mains supply.
N/A
3.2.3
Permanently connected equipment
The equipment is not
permanently connected.
N/A
Number of conductors, diameter (mm) of cable and
conduits................................ .............................:
-
3.2.4
Appliance inlets
The unit is provided with a
means for direct plug-in.
N/A
3.2.5
Power supply cords
The unit is provided with a
means for direct plug-in.
N/A
3.2.6
Type..................................................................:
-
Rated current (A), cross-sectional area (mm²),AWG
.........................................................................:
-
Cord anchorages and strain relief
The unit is provided with a
means for direct plug-in.
N/A
Mass of equipment (kg), pull (N)..........................:
-
Longitudinal displacement (mm)..........................:
-
3.2.7
Protection against mechanical damage
N/A
3.2.8
Cord guards
N/A
3.2.9
D (mm); test mass (g) .........................................:
-
Radius of curvature of cord (mm) ........................:
-
Supply wiring space
TRF No.: 1950__F
N/A
UL International Demko A/S
TRF originator: FIMKO
Issue Date:
2003-09-25
Page 19 of 42
Report Reference #
E203413-A17-CB-1
IEC 60950
Clause
Requirement + Test
3.3
Wiring Terminals for Connection of External Conductors
N/A
3.3.1
Wiring terminals
N/A
3.3.2
Connection of non-detachable power supply cords
N/A
3.3.3
Screw terminals
N/A
3.3.4
Rated current (A), cord/cable type, cross-sectional
area (mm²) .........................................................:
N/A
3.3.5
Rated current (A), type and nominal thread
diameter (mm) ...................................................:
N/A
3.3.6
Wiring terminals design
N/A
3.3.7
Grouping of wiring terminals
N/A
3.3.8
Stranded wire
N/A
3.4
Disconnection From the A.C. Mains Supply
Pass
3.4.1
General requirement
Pass
3.4.2
Disconnect devices
3.4.3
Permanently connected equipment
N/A
3.4.4
Parts which remain energized
N/A
3.4.5
Switches in flexible cords
N/A
3.4.6
Single-phase equipment
Disconnect device disconnects
both poles simultaneously.
3.4.7
Three-phase equipment
The equipment is singlephased.
3.4.8
Switches as disconnect devices
3.4.9
Plugs as disconnect devices
3.4.10
Interconnected equipment
3.4.11
Multiple power sources
TRF No.: 1950__F
Result - Remark
Verdict
The plug is considered to be
the disconnect device.
Pass
Pass
N/A
N/A
Pass
N/A
One power source only.
UL International Demko A/S
N/A
TRF originator: FIMKO
Issue Date:
2003-09-25
Page 20 of 42
Report Reference #
E203413-A17-CB-1
IEC 60950
Clause
Requirement + Test
Result - Remark
3.5
Interconnection of Equipment
3.5.1
General requirements
Verdict
Pass
This equipment is only
considered for connection to
SELV.
Pass
Ref. to 2.2 for other details.
3.5.2
Types of interconnection circuits .........................: Interconnection circuits are
SELV CIRCUITS.
3.5.3
ELV circuits as interconnection circuits
4
PHYSICAL REQUIREMENTS
4.1
Stability
N/A
Angle of 10°
N/A
Test: force (N) ....................................................:
N/A
TRF No.: 1950__F
No ELV interconnections.
UL International Demko A/S
Pass
N/A
Pass
TRF originator: FIMKO
Issue Date:
2003-09-25
Page 21 of 42
Report Reference #
E203413-A17-CB-1
IEC 60950
Clause
Requirement + Test
Result - Remark
Verdict
4.2
Mechanical strength
4.2.1
General
See below.
Pass
4.2.2
Steady force test, 10 N
10N were applied to
components.
Pass
Pass
No energy or other hazards.
4.2.3
Steady force test, 30 N
No internal enclosure.
4.2.4
Steady force test, 250 N
250N were applied to the outer
enclosure.
N/A
Pass
No energy or other hazards.
4.2.5
Impact test
4.2.6
Drop test
4.2.7
Stress relief
4.2.8
Cathode ray tubes
N/A
Picture tube separately certified ..........................:
N/A
4.2.9
High pressure lamps
N/A
4.2.10
Wall or ceiling mounted equipment; force (N) .......:
N/A
TRF No.: 1950__F
N/A
Pass
No indication of shrinkage or
distortion on enclosures due to
the stress relief test (70 degree
C/7 h). See Annex A.10.
UL International Demko A/S
Pass
TRF originator: FIMKO
Issue Date:
2003-09-25
Page 22 of 42
Report Reference #
E203413-A17-CB-1
IEC 60950
Clause
Requirement + Test
Result - Remark
Verdict
4.3
Design and Construction
4.3.1
Edges and corners
4.3.2
Handles and manual controls; force (N) ...............:
N/A
4.3.3
Adjustable controls
N/A
4.3.4
Securing of parts
N/A
4.3.5
Connection of plugs and sockets
Pass
4.3.6
Direct plug-in equipment
Pass
Pass
All edges and corners judged
to be sufficiently well rounded
so as not to constitute a
hazard.
Torque (Nm)......................................................:
Pass
-
4.3.7
Heating elements in earthed equipment
N/A
4.3.8
Batteries
N/A
4.3.9
Oil and grease
N/A
4.3.10
Dust, powders, liquids and gases
N/A
4.3.11
Containers for liquids or gases
N/A
4.3.12
Flammable liquids ..............................................:
N/A
Quantity of liquid (l) ............................................:
N/A
Flash point (°C)..................................................:
N/A
Radiation; type of radiation .................................:
N/A
Equipment using lasers
N/A
4.4
Protection Against Hazardous Moving Parts
N/A
4.4.1
General
N/A
4.4.2
Protection in operator access areas
N/A
4.4.3
Protection in restricted access locations
N/A
4.4.4
Protection in service access areas
N/A
4.3.13
TRF No.: 1950__F
UL International Demko A/S
TRF originator: FIMKO
Issue Date:
2003-09-25
Page 23 of 42
Report Reference #
E203413-A17-CB-1
IEC 60950
Clause
Requirement + Test
4.5
Thermal Requirements
4.5.1
Temperature rises
Result - Remark
Verdict
Pass
(see appended table 4.5)
Pass
Normal load condition per Annex L......................: Operated in the most
unfavorable way of operation
given in the operating
instructions until steady
conditions established.
Pass
4.5.2
Resistance to abnormal heat
Pass
4.6
Openings in Enclosures
4.6.1
Top and side openings
It has been determined from
examination of the physical
characteristics of the materials
used that the material meets
the requirements of the test.
See Appended Table 4.5.2.
N/A
No opening.
Dimensions (mm)...............................................:
4.6.2
Bottoms of fire enclosures
N/A
-
No bottom opening.
Construction of the bottom ..................................:
N/A
-
4.6.3
Doors or covers in fire enclosures
N/A
4.6.4
Openings in transportable equipment
N/A
4.6.5
Adhesives for constructional purposes
N/A
Conditioning temperature/time ............................:
TRF No.: 1950__F
UL International Demko A/S
-
TRF originator: FIMKO
Issue Date:
2003-09-25
Page 24 of 42
Report Reference #
E203413-A17-CB-1
IEC 60950
Clause
Requirement + Test
Result - Remark
Verdict
4.7
Resistance to Fire
4.7.1
Reducing the risk of ignition and spread of flame
4.7.2
Conditions for a fire enclosure
4.7.2.1
Parts requiring a fire enclosure
4.7.2.2
Parts not requiring a fire enclosure
4.7.3
Mat erials
4.7.3.1
General
See below.
Pass
4.7.3.2
Materials for fire enclosures
V-1 minimum.
Pass
4.7.3.3
Materials for components and other parts outside
fire enclosures
4.7.3.4
Materials for components and other parts inside fire All internal materials are rated
enclosures
V-2 or better or are mounted
on a PWB rated V-1 or better.
Pass
Method 1: Selection and
application of components and
materials which minimize the
possibility of ignition and
spread of flame.
Pass
Pass
A fire enclosure covers all
parts.
Pass
N/A
Pass
N/A
Pass
See Table 1.5.1 for material
information.
4.7.3.5
Materials for air filter assemblies
N/A
4.7.3.6
Materials used in high-voltage components
N/A
5
ELECTRICAL REQUIREMENTS AND SIMULATED ABNORMAL CONDITIONS
TRF No.: 1950__F
UL International Demko A/S
Pass
TRF originator: FIMKO
Issue Date:
2003-09-25
Page 25 of 42
Report Reference #
E203413-A17-CB-1
IEC 60950
Clause
Requirement + Test
Result - Remark
Verdict
5.1
Touch current and protective conductor current
5.1.1
General
See below.
Pass
5.1.2
Equipment under test (EUT)
Equipment designed for
connection to only one power
source.
Pass
5.1.3
Test circuit
Single phase equipment
intended only for connection to
star TN or TT system.
Pass
5.1.4
Application of measuring instrument
Test made to 10X20 cm metal
foil in contact with accessible
non-conductive part.
Pass
5.1.5
Test procedure
Pass
5.1.6
Tes t measurements
Pass
Pass
Test voltage (V)..................................................: 254 V ac
-
Measured current (mA).......................................: 0.025 A maximum
-
Max. allowed current (mA)..................................: 0.25 mA.
-
5.1.7
Equipment with touch current exceeding 3.5 mA ..:
5.1.8
Touch currents to and from telecommunication
networks
5.1.8.1
Limitation of the touch current to a
telecommunication network
N/A
No TNV circuit.
N/A
N/A
Test voltage (V)..................................................:
-
Measured current (mA).......................................:
-
Max. allowed current (mA)..................................:
-
5.1.8.2
Summation of touch currents from
telecommunication networks
N/A
5.2
Electric Strength
5.2.1
General
Based on the electric strength
test the use of the insulating
materials within the equipment
is satisfactory.
Pass
5.2.2
Test procedure
No insulation breakdown
detected during the test.
Pass
Pass
(see appended table 5.2)
TRF No.: 1950__F
UL International Demko A/S
TRF originator: FIMKO
Issue Date:
2003-09-25
Page 26 of 42
Report Reference #
E203413-A17-CB-1
IEC 60950
Clause
Requirement + Test
Result - Remark
Verdict
5.3
Abnormal Operating and Fault Conditions
5.3.1
Protection against overload and abnormal
operation
(see appended table 5.3)
5.3.2
Motors
No motors.
5.3.3
Transformers
Transformers are constructed
in accordance with the
applicable Clause and Annex
C.
Pass
Pass
N/A
Pass
(see appended Annex C)
5.3.4
Functional insulation...........................................: Functional insulation complies
with method (c). See 5.3.8.
5.3.5
Electromechanical components
5.3.6
Simulation of faults
5.3.7
Unattended equipment
5.3.8
Compliance criteria for abnormal operating and
fault conditions
6
CONNECTION TO TELECOMMUNICATION NETWORKS
N/A
6.1
Protection of telecommunication network service personnel, and users of
other equipment connected to the network, from hazards in the equipment
N/A
6.1.1
Protection from hazardous voltages
N/A
6.1.2
Separation of the telecommunication network from earth
N/A
6.1.2.1
Requirements
N/A
6.1.2.2
Pass
N/A
See appended table 5.3.
Pass
N/A
No fire, emission of molten
metal or deformation was
noted during the tests. Electric
Strength tests performed after
abnormal and fault tests.
Pass
Test voltage (V)..................................................:
-
Current in the test circuit(mA)..............................:
-
Exclusions .........................................................:
N/A
TRF No.: 1950__F
UL International Demko A/S
TRF originator: FIMKO
Issue Date:
2003-09-25
Page 27 of 42
Report Reference #
E203413-A17-CB-1
IEC 60950
Clause
Requirement + Test
Result - Remark
Verdict
6.2
Protection of Equipment Users From Overvoltages on Telecommunication
Networks
N/A
6.2.1
Separation requirements
N/A
6.2.2
Electric strength test procedure
N/A
6.2.2.1
Impulse test
N/A
6.2.2.2
Steady-state test
N/A
6.2.2.3
Compliance criteria
N/A
6.3
Protection of Telecommunication Wiring System From Overheating
N/A
Max. output current (A) .......................................:
-
Current limiting method.......................................:
-
A
ANNEX A, TESTS FOR RESISTANCE TO HEAT AND FIRE
Pass
A.1
Flammability test for fire enclosures of movable equipment having a total
mass exceeding 18 kg, and of stationary equipment (see 4. 7.3.2)
A.1.1
Samples, material ..............................................:
-
Wall thickness (mm) ...........................................:
-
A.1.2
Conditioning of samples; temperature (°C) ...........:
N/A
A.1.3
Mounting of samples ..........................................:
N/A
A.1.4
Test flame
N/A
A.1.5
Test procedure
N/A
A.1.6
Compliance criteria
N/A
N/A
Sample 1 burning time (s)...................................:
-
Sample 2 burning time (s)...................................:
-
Sample 3 burning time (s)...................................:
-
TRF No.: 1950__F
UL International Demko A/S
TRF originator: FIMKO
Issue Date:
2003-09-25
Page 28 of 42
Report Reference #
E203413-A17-CB-1
IEC 60950
Clause
Requirement + Test
A.2
Flammability test for fire enclosures of movable equipment having a total
mass not exceeding 18 kg, and for material and components located inside
fire enclosures (see 4.7.3.2 and 4.7.3.4)
A.2.1
Samples, material ..............................................:
-
Wall thickness (mm) ...........................................:
-
A.2.6
A.2.7
Result - Remark
Compliance criteria
Verdict
N/A
N/A
Sample 1 burning time (s)...................................:
-
Sample 2 burning time (s)...................................:
-
Sample 3 burning time (s)...................................:
-
Alternative test acc. to IEC 60695-2-2, cl. 4, 8
N/A
Sample 1 burning time (s)...................................:
-
Sample 2 burning time (s)...................................:
-
Sample 3 burning time (s)...................................:
-
A.3
High current arcing ignition test (see 4.7.3.2)
A.3.1
Samples, material ..............................................:
-
Wall thickness (mm) ...........................................:
-
A.3.5
Compliance criteria
N/A
N/A
Sample 1 number of arcs to ignition (pcs) ............:
-
Sample 2 number of arcs to ignition (pcs) ............:
-
Sample 3 number of arcs to ignition(pcs).............:
-
Sample 4 number of arcs to ignition(pcs).............:
-
Sample 5 number of arcs to ignition (pcs) ............:
-
TRF No.: 1950__F
UL International Demko A/S
TRF originator: FIMKO
Issue Date:
2003-09-25
Page 29 of 42
Report Reference #
E203413-A17-CB-1
IEC 60950
Clause
Requirement + Test
A.4
Hot wire ignition test (see 4.7.3.2)
A.4.1
Samples, material ..............................................:
-
Wall thickness (mm) ...........................................:
-
A.4.5
Result - Remark
Verdict
N/A
Compliance criteria
N/A
Sample 1 ignition time (s) ...................................:
-
Sample 2 ignition time (s) ...................................:
-
Sample 3 ignition time (s) ...................................:
-
Sample 4 ignition time (s) ...................................:
-
Sample 5 ignition time (s) ...................................:
-
A.5
Hot flaming oil test (see 4.6.2)
N/A
A.6
Flammability tests for classifying materials V-0, V-1 or V-2
N/A
A.6.1
Samples, material ..............................................:
-
Wall thickness (mm) ...........................................:
-
A.6.5
Compliance criteria
N/A
A.6.6
Permitted retest
N/A
A.7
Flammability test for classifying foamed materials HF-1, HF -2 or HFB
N/A
A.7.1
Sample, material ................................................:
-
Wall thickness (mm) ...........................................:
-
A.7.4
Compliance criteria
N/A
A.7.5
Compliance criteria, HF-2
N/A
A.7.6
Compliance criteria, HF-1
N/A
A.7.7
Compliance criteria, HBF
N/A
A.7.8
Permitted retest, HF-1 or HF-2
N/A
A.7.9
Permitted retest, HBF
N/A
TRF No.: 1950__F
UL International Demko A/S
TRF originator: FIMKO
Issue Date:
2003-09-25
Page 30 of 42
Report Reference #
E203413-A17-CB-1
IEC 60950
Clause
Requirement + Test
Result - Remark
Verdict
A.8
Flammability test for classifying materials HB
A.8.1
Samples, material ..............................................:
-
Sample thickness (mm) ......................................:
-
A.8.2
Conditioning of samples; temperature (°C) ...........:
N/A
A.8.4
Test procedure
N/A
A.8.5
Compliance criteria
N/A
A.8.6
Permitted retest
N/A
A.9
Flammability test for classifying materials 5V
N/A
A.9.1
Samples, material ..............................................:
-
Sam ple thickness (mm) ......................................:
-
N/A
A.9.4
Test procedure, test bars
N/A
A.9.5
Test procedure, test plaques
N/A
A.9.6
Compliance criteria
N/A
A.9.7
Permitted retest
N/A
A.10
Stress relief conditioning (see 4.2.7)
Temperature (°C) ...............................................: 70
TRF No.: 1950__F
UL International Demko A/S
Pass
-
TRF originator: FIMKO
Issue Date:
2003-09-25
Page 31 of 42
Report Reference #
E203413-A17-CB-1
IEC 60950
Clause
Requirement + Test
Result - Remark
Verdict
B
ANNEX B, MOTOR TESTS UNDER ABNORMAL CONDITIONS (see 4.7.2.2 and
5.3.2)
N/A
B.1
General requirements
N/A
Position ................................ .............................:
-
Manufacturer ................................ .....................:
-
Type..................................................................:
-
Rated values......................................................:
-
B.2
Test conditions
N/A
B.3
Maximum temperatures
N/A
B.4
Running overload test
N/A
B.5
Locked-rotor overload test
N/A
Test duration (days) ...........................................:
-
Electric strength test: test voltage (V)...................:
-
B.6
Running overload test for DC motors in secondary
circuits
N/A
B.7
Locked-rotor overload test for DC motors in secondary circuits
N/A
B.7.1
Test procedure
N/A
B.7.2
Alternative test procedure; test time (h)................:
N/A
B.7.3
Electric strength test
N/A
B.8
Test for motors with capacitors
N/A
B.9
Test for three-phase motors
N/A
B.10
Test for series motors
N/A
Operating voltage (V ) .........................................:
TRF No.: 1950__F
UL International Demko A/S
-
TRF originator: FIMKO
Issue Date:
2003-09-25
Page 32 of 42
Report Reference #
E203413-A17-CB-1
IEC 60950
Clause
Requirement + Test
Result - Remark
C
ANNEX C, TRANSFORMERS (see 1.5.4 and 5.3.3)
Verdict
Pass
Position ................................ .............................: (see appended table 1.5.1)
-
Manufacturer ................................ .....................: (see appended table 1.5.1)
-
Type..................................................................: (see appended table 1.5.1)
-
Rated values......................................................: (see appended table 1.5.1)
-
Method of protection...........................................: (see appended table 1.5.1)
-
C.1
Overload test
Evaluated as part of power
supply.
Pass
C.2
Insulation
(see appended table 5.2)
Pass
Protection from displacement of windings ............: Triple insulated wire used.
Pass
For transformer in power
supply, evaluated as part of
power supply.
G
ANNEX G, ALTERNATIVE METHOD FOR DETERMINING MINIMUM
CLEARANCES
N/A
G.1
Summary of the procedure for determining
minimum clearances
N/A
G.2
Determination of mains transient voltage (V) ........:
N/A
G.3
Determination of telecommunication network
transient voltage (V) ...........................................:
N/A
G.4
Determination of required withstand voltage (V) ...:
N/A
G.5
Measurement of transient levels (V) ....................:
N/A
G.6
Determination of minimum clearances .................:
N/A
H
ANNEX H, IONIZING RADIATION (see 4.3.13)
N/A
Ionizing radiation
N/A
Measured radiation (mR/h) .................................:
-
Measured high -voltage (kV) ................................:
-
Measured focus voltage (kV)...............................:
-
CRT markings ....................................................:
-
TRF No.: 1950__F
UL International Demko A/S
TRF originator: FIMKO
Issue Date:
2003-09-25
Page 33 of 42
Report Reference #
E203413-A17-CB-1
IEC 60950
Clause
Requirement + Test
Result - Remark
Verdict
J
ANNEX J, TABLE OF ELECTROCHEMICAL POTENTIALS (see 2.6.5.6)
Metal used .........................................................:
N/A
-
K
ANNEX K, THERMAL CONTROLS (see 1.5.3 and 5.3.7)
N/A
K.1
Making and breaking capacity
N/A
K.2
Thermostat reliability; operating voltage (V)..........:
N/A
K.3
Thermostat endurance test; operating voltage (V) :
N/A
K.4
Temperature limiter endurance; operating voltage
(V)................................ ................................ .....:
N/A
K.5
Thermal cut-out reliability
N/A
K.6
Stability of operation
N/A
M
ANNEX M, CRITERIA FOR TELEPHONE RINGING SIGNALS (see 2.3.1)
N/A
M.2
Method A
N/A
M.3
Method B
N/A
M.3.1
Ringing signal
N/A
M.3.1.1
Frequency (f) ................................ .....................:
-
M.3.1.2
Voltage (V) ........................................................:
-
M.3.1.3
Cadence; time (s), voltage (V) .............................:
-
M.3.1.4
Single fault current (mA)................................ .....:
-
M.3.2
Tripping device and monitoring voltage ................:
N/A
M.3.2.1
Conditions for use of a tripping device or a
monitoring voltage
N/A
M.3.2.2
Tripping device
N/A
M.3.2.3
Monitoring voltage (V).........................................:
N/A
U
ANNEX U, INSULATED WINDING WIRES FOR USE WITHOUT INTERLEAVED
INSULATION (see 2.10.5.4)
Pass
Separate test report
Pass
TRF No.: 1950__F
(see appended table 1.5.1)
UL International Demko A/S
TRF originator: FIMKO
Issue Date:
2003-09-25
Page 34 of 42
Report Reference #
E203413 -A17-CB-1
IEC 60950
Clause
Requirement + Test
Result - Remark
1.5.1
TABLE: list of critical components
Verdict
Pass
object/part No.
manufacturer/
trademark
type/model
technical data
standard
mark(s) of
1
conformity )
01. PWB
--
--
UL796
UL, --
02. Varistor
(R31)
03. Transient
Voltage
Suppressors
(D4, D5)
04. X-Cap. (C39)
Centra Science
Corp.
Concord
Semiconductor
Corp.
CNR-07D471K
Minimum V-1,
105 degree C
Minimum 250
Vac
Minimum
breakdown
voltage 7.60 V.
UL1449
UL, --
UL1449
UL, --
Hua Jung
Components
Co., Ltd.
ISKRA
Kondenzatorji
d.d.
Matsushita
Electric Ind. Co.,
Ltd.
Murata
Manufacturing
Co., Ltd.
Pan Overseas
Electronics Co.,
Ltd.
TDK Corp.
MKP
--
--
UL1283,
IEC60384-14
/1993
UL1283,
IEC60384-14
/1993
UL1283,
IEC60384-14
/1993
UL1283,
IEC60384-14
/1993
UL1283,
IEC60384-14
/1993
UL1283,
IEC60384-14
/1993
--
--, VDE
05. Transformer
(T1)
05-1.
Transformer Coil (Triple
insulation wire)
Rubadue Wire
Co., Inc.
T28A01T292-2,
T28A01T949-2,
or T28A01T5952
Maximum
0.01uF, 250 Vac,
CLass X1 or X2.
Maximum
0.01uF, 250 Vac,
CLass X1 or X2.
Maximum
0.01uF, 250 Vac,
CLass X1 or X2.
Maximum
0.01uF, 250 Vac,
CLass X1 or X2.
Maximum
0.01uF, 250 Vac,
CLass X1 or X2.
Maximum
0.01uF, 250 Vac,
CLass X1 or X2.
Class 105
degree C, see
Enclosure
diagram 04-1 for
detail.
Insulation wire;
B1-B2: 0.32 mm
diameter by 3
turns; G1-G2:
0.32 mm
diameter by 3
turns; R1-R2:
0.32 mm
diameter by 3
turns
UL2353
UL, --
04a. X-Cap.
(C39)
04b. X-Cap.
(C39) (Alternate)
04c. X-Cap.
(C39) (Alternate)
04d. X-Cap.
(C39) (Alternate)
04e. X-Cap.
(C39) (Alternate)
TRF No.: 1950__F
SAC5.0
KNB 1560, KNB
1562, or KNB
1563
ECQUG
KH or KX
PY
CS
UL International Demko A/S
--, VDE
--, VDE
--, VDE
--, VDE
--, VDE
--, --
TRF originator: FIMKO
Issue Date:
2003-09-25
Page 35 of 42
Report Reference #
E203413 -A17-CB-1
IEC 60950
Clause
Requirement + Test
Result - Remark
05-2
Transformer Core
--
--
05-3.
Transformer Tubing
Fluo Tech
Industries Co.,
Ltd.
TFL
05-4.
Transformer Glue
Dow Corning
Corp.
3165
05-5.
Transformer Heat shrink
Tubing
--
--
06. Power
Module
Universal
Microelectronics
Co., Ltd.
UP0051A-05
07. Insulator
Formex, Div Of
Illinois Tool
Works Inc,
Formerly
FORMEX GK
08. Shielding
--
--
09. Enclosure
GE Plastics
Pacifics
945
10. Connector
--
--
TRF No.: 1950__F
Toroidal core,
ferrite, 9.3 mm
OD by 4.8 mm
ID by 1.3 mm
thick
Minimum 200
degree C, 150 V,
Provided on the
end lead of coil.
V-2 minimum,
Provide on the
bottom of
transformer.
FEP, PTFE,
PVC, TFE,
neoprene,
polyimide or
marked VW -1;
105 degree C,
300 V
I/P: 100-240Vac,
47-63Hz, 0.2A
maximum; O/P:
5Vdc, 1A
V-0 minimum,
115 degree C.
Overall see
Enclosure
diagram 4-02 for
detail dimension,
minimum 0.41
mm, located
between power
module and
shielding.
Metal, overall
see Enclosure
diagram 4-02 for
detail dimension.
V-0, 80 degree
C, overall 112.6
by 63.6 by 44.0
mm, minimum
2.0 mm thick.
SELV, RJ-45,
one provided
UL International Demko A/S
Verdict
--
--, --
UL224
UL, --
UL94
UL, --
UL224
UL, --
UL60950,
IEC60950: 1999
UL, TUV CB Cert
No. JPTUV006434
UL94, UL746C
UL, --
--
--, --
UL94, UL746C
UL, --
--
--, --
TRF originator: FIMKO
Issue Date:
2003-09-25
Page 36 of 42
Report Reference #
E203413 -A17-CB-1
IEC 60950
Clause
Requirement + Test
Result - Remark
11. Internal
wiring
--
--
12.
Interconnecting
Cable (Optional)
--
--
13. Insulating
Tubing/Sleeving
--
--
1
FEP, PTFE,
UL758
PVC, TFE,
neoprene,
polyamide or
marked VW -1;
minimum 300 V,
80 degree C.
Minimum 80
UL758
degree C, 30 V,
maximum 3.05
m long, jacketed,
VW-1 or FT-1.
FEP, PTFE,
UL224
PVC, TFE,
neoprene,
polyimide or
marked VW -1;
105 degree C,
300 V
Verdict
UL, --
UL, --
UL, --
) an asterisk indicates a mark which assures the agreed level of surveillance
TRF No.: 1950__F
UL International Demko A/S
TRF originator: FIMKO
Issue Date:
2003-09-25
Page 37 of 42
Report Reference #
E203413-A17-CB-1
IEC 60950
Clause
Requirement + Test
1.6.2
TABLE: electrical data (in normal conditions)
fuse #
---------
I rated (A)
--0.1
0.1
0.1
0.1
---
Result - Remark
U (V)
P (W)
90/47Hz
90/63Hz
100/47Hz
100/63Hz
240/47Hz
240/47Hz
254/47Hz
254/63Hz
3.0
3.1
2.9
2.9
2.5
2.4
2.8
2.6
I (mA)
Verdict
Pass
I fuse (mA) condition/status
60
60
54
54
29
30
29
30
---------
Maximum
Maximum
Maximum
Maximum
Maximum
Maximum
Maximum
Maximum
normal
normal
normal
normal
normal
normal
normal
normal
load
load
load
load
load
load
load
load
supplementary information:
Maximum normal load: Connect to computer and transmit data continuously.
2.10.3 and
2.10.4
TABLE: clearance and creepage distance measurements
clearance cl and creepage
distance dcr at/of:
CN1 (power module) to
shielding
F1 (power module) to shielding
J1 to U4 pin1
Under T1
Up
(V)
U r.m.s. (V) required cl
(mm)
Pass
cl (mm)
required
dcr (mm)
dcr
(mm)
<448
<250
4.2
>5.0
5.0
>5.0
<448
<448
<420
<250
<250
<250
4.2
4.2
4.0
>5.0
>5.0
>5.0
5.0
5.0
5.0
>5.0
>5.0
>5.0
supplementary information:
--
2.10.5
TABLE: distance through insulation measurements
distance through insulation di at/of:
Insulation sheet
Enclosure
U r.m.s.
(V)
240
240
test voltage (V)
3000
3000
Pass
required di
(mm)
0.4
0.4
di
(mm)
>0.41
>2
supplementary information:
--
TRF No.: 1950__F
UL International Demko A/S
TRF originator: FIMKO
Issue Date:
2003-09-25
Page 38 of 42
Report Reference #
E203413-A17-CB-1
IEC 60950
Clause
Requirement + Test
Result - Remark
4.5
TABLE: temperature rise measurements
Verdict
Pass
test voltage (V) ................................................. : 63 HZ,
90 Vac, 2.5hrs, Horizontal / 254
Vac, 2.5hrs, Horizontal / 90
Vac, 2hrs, Vertical / 254 Vac,
2hrs, Vertical
t1 (°C) ............................................................. : --
—
t2 (°C) ............................................................. : Ambient = 25.7 / 24.5 / 25.3 /
25.0 degree C
—
temperature rise dT of part/at:
dT (K)
C1 body (power unit)
T1 coil (power unit)
T1 core (power unit)
PWB near IC1 (power unit)
LX coil (power unit)
T1 coil
Enclosure inside
Enclosure outside
temperature rise dT of winding:
--
required dT (K)
37.2 / 42.6 / 36.7 /
41.2
34.5 / 40.0 / 34.0 /
38.5
39.5 / 45.5 / 38.6 /
43.7
39.7 / 46.0 / 38.9 /
44.2
33.3 / 37.5 / 32.7 /
35.9
35.6 /40.0 / 34.6 /
38.0
26.0 /29.7 / 26.0 /
28.5
15.0 /17.8 / 14.5 /
15.9
9.9 / 11.6 / 9.4 / 10.0
L1 coil (power unit)
R2 ( Ω )
R1 (Ω)
--
--
dT (K)
--
—
65
65
70
70
65
65
50
40
40
required dT
(K)
--
insulation
class
--
supplementary information:
Maximum normal load: Connect to computer and transmit data continuously.
Tmra = 40 degree C, the maximum temperature rise is calculated as follows:
Winding components:Transformer - Class A: dTmax = 75K - 10K-(40-25)K = 50 K
Winding components:Transformer - Class B: dTmax = 95K - 10K-(40-25)K = 70 K
Components with:
- maximum absolute temp. of 105 degree C (PWB): dTmax = (105-40)K = 65 K
- when no class of insulation is given, minimum insulation 105 degree C assumed.
- maximum absolute temp. of 80 degree C (Enclosure): dTmax = (80-40)K = 40 K
User Accessible Area:
- material is plastic (70K) dTmx = 70K-(40-25)K = 55K
TRF No.: 1950__F
UL International Demko A/S
TRF originator: FIMKO
Issue Date:
2003-09-25
Page 39 of 42
Report Reference #
E203413-A17-CB-1
IEC 60950
Clause
Requirement + Test
Result - Remark
4.5.2
TABLE: ball pressure test of thermoplastics
Verdict
Pass
allowed impression diameter (mm)..................... : 2 mm
—
part
test temperature (°C)
Enclosure, GE Plastics/945, 2.4 mm
125
impression diameter
(mm)
1
supplementary information:
--
5.2
TABLE: electric strength tests and impulse tests
Pass
test voltage applied between:
test voltage (V)
Primary to SELV
Primary to Enclosure with foil
T1 primary winding to SELV winding
T1 primary winding to core
T1 SELV winding to core
4242
4242
3000
3000
3000
breakdown
Yes / No
Vdc
Vdc
Vac
Vac
Vac
No
No
No
No
No
supplementary information:
--
5.3
TABLE: fault condition tests
Pass
ambient temperature (°C) .................................. : See below
—
model/type of power supply............................... : --
—
manufacturer of power supply............................ : --
—
rated markings of power supply ......................... : --

component
No.
fault
C25
T1 (B1-B2)
Short
Short
240 Vac
240 Vac
< 1S
2 hrs
---
0.03 - 0
0.03
T1 (G1-G2) Short
240 Vac
2 hrs
--
0.03
RJ45 Pin18 to ground
240 Vac
1 min
--
0.03
Overload
TRF No.: 1950__F
test voltage
(V)
test time
fuse
No.
fuse current
(A)
UL International Demko A/S
result
Breaker open, NB, NC, NT.
NO, NB, NC, NT, CT.
Maximum temperature T1
coil: 58 degree C, Ambient:
25.7 degree C.
NO, NB, NC, NT, CT.
Maximum temperature T1
coil: 51.3 degree C,
Ambient: 25.8 degree C.
NO, NB, NC, NT. Open
circuit voltage measured 0
V.
TRF originator: FIMKO
Issue Date:
2003-09-25
Page 40 of 42
Report Reference #
E203413-A17-CB-1
IEC 60950
Clause
Requirement + Test
Result - Remark
Verdict
supplementary information:
Comments Key: NO - Normally operated NB - No indication of dielectric breakdown NC - Cheesecloth
remained intact NT - Tissue paper remained intact CT - Constant temperatures were obtained
A.6.5
TABLE: flammability test for classifying materials V-0, V-1 or V-2
sample
No. / ref.
afterflame time (s) t1 or t 2
N/A
afterflame + afterglow (s) after 2nd flame
application t 2 + t 3
supplementary information:
A.6.6
TABLE: flammability re -test for classifying materials V-0, V-1 or V-2
sample
No.
afterflame time (s) t1 or t 2
N/A
afterflame + afterglow (s) after 2nd flame
application t 2 + t 3
supplementary information:
A.7.4,
A.7.5,
A.7.6 and
A.7.7
sample
No. / ref.
TABLE: flammability test for classifying foam materials HF-1, HF -2 or HBF
flame time (s)
glow time (s)
flaming/glowing distance
from the end (mm)
N/A
comment (for A.7.7
burning rate mm/min)
supplementary information:
A.7.8
sample
No.
TABLE: flammability re -test for classifying foam materials HF-1 or HF-2
flame time (s)
glow time (s)
flaming/glowing distance
from the end (mm)
N/A
comment
supplementary information:
TRF No.: 1950__F
UL International Demko A/S
TRF originator: FIMKO
Issue Date:
2003-09-25
Page 41 of 42
Report Reference #
E203413-A17-CB-1
IEC 60950
Clause
Requirement + Test
A.7.9
TABLE: flammability re -test for classifying foam materials HBF
sample
No.
flame time (s)
Result - Remark
glow time (s)
flaming/glowing distance
from the end (mm)
Verdict
N/A
comment (for A.7.7
burning rate mm/min)
supplementary information:
A.8.5
TABLE: flammability test for classifying materials HB
sample
No.
flaming/glowing rate
mm/min
N/A
flaming/glowing distance from reference mark
(mm)
supplementary information:
A.8.6
TABLE: flammability re -test for classifying materials HB
sample
No.
flaming/glowing rate
N/A
flaming/glowing distance from reference mark
(mm)
mm/min
supplementary information:
A.9.6
TABLE: flammability test for classifying materials 5V
sample
No./ref.
test bars
flaming +
glowing time (s)
N/A
test plaques
burning distance
(mm)
position
flaming + glowing time
(s)
burning distance
(mm)
supplementary information:
A.9.7
TABLE: flammability re -test for classifying materials 5V
TRF No.: 1950__F
UL International Demko A/S
N/A
TRF originator: FIMKO
Issue Date:
2003-09-25
Page 42 of 42
Report Reference #
E203413-A17-CB-1
IEC 60950
Clause
Requirement + Test
sample
No.
Result - Remark
test bars
flaming +
glowing time (s)
Verdict
test plaques
burning distance
(mm)
position
flaming + glowing time
(s)
burning distance
(mm)
supplementary information:
TRF No.: 1950__F
UL International Demko A/S
TRF originator: FIMKO
Issue Date:
2003-09-25
Page 1 of 25
Report Reference #
Enclosure
National Differences
(Total 25 Pages including this Cover Page)
Austria**
Belgium**
Czech Republic*
Denmark
Finland
France**
Germany
Greece**
Group
Hungary*
Ireland
Italy**
Japan
Netherlands**
Norway
Poland*
Slovakia*
Slovenia*
South Africa*
Spain
Sweden
Switzerland
USA / Canada
Yugoslavia*
* No National Differences Declared
** Only Group Differences
UL International Demko A/S
E203413-A17-CB-1
Issue Date:
2003-09-25
Page 2 of 25
Report Reference #
E203413-A17-CB-1
IEC 60950
SubClause Difference + Test
Result - Remark
Verdict
Denmark - Differences to IEC60950, Third Edition (1999)
1.2.4.1
Certain types of Class I appliances (see sub-clause
3.2.1) may be provided with plug not establishing
earthing continuity when inserted into Danish
socket-outlets.
N/A
1.7.2
Supply cords of Class I equipment, which is
delivered without a plug, must be provided with a
visible tag with the following text:
N/A
"Vigtigt !
Lederen med grøn/gul isolation må kun
tilsluttes en klemme mæ rket
(IEC 417, No. 5019) eller (IEC 417, No. 5017)."
If essential for the safety of the equipment, the tag
must in addition be provided with a diagram, which
shows the connection of the other conductors, or
be provided with the following text:
"For tilslutning af de øvrige ledere, se medfølgende
installationsvejledning".
1.7.5.a
Socket-outlets for providing power to other
equipment shall be in accordance with the Heavy
Current Regulations, Section 107-2-D1, Standard
Sheet DK 1-3a, DK 1-5a or DK 1-7a, when used on
Class I equipment.
1.7.5.b
Class II equipment shall not be fitted with socketoutlets for providing power to other equipment.
1.7.15
Caution text concerning lithium batteries:
ADVARSEL!
Lithiumbatteri - Eksplosionsfare ved fejlagtig
håndtering.
Udskiftning må kun ske med batteri af samme
fabrikat og type.
Levér det brugte batteri tilbage tilleverandøren.
The size of the warning must be a minimum of 26 x
52 mm, the background shall be yellow colour with
black frame, and the text in black colour. A white
background is acceptable in the User's Instruction
and in the Service Manual.
UL International Demko A/S
N/A
Pass
N/A
Issue Date:
2003-09-25
Page 3 of 25
Report Reference #
E203413-A17-CB-1
IEC 60950
SubClause Difference + Test
3.2.1
Result - Remark
Supply cord of single-phase equipment having a
rated current not exceeding 10 A shall be provided
with a plug according to the Heavy Current
Regulations, Section 107 -2-D1.
Verdict
N/A
Class I equipment provided with socket-outlets with
earth contact or which are intended to be used in
locations where protection against indirect contact
is required according to the wiring rules shall be
provided with a plug in accordance with standard
sheet DK 2-1a or DK 2-5a.
If poly-phase equipment and single-phase
equipment having a rated current exceeding 10 A
is provided with a supply cord with a plug, this plug
shall be in accordance with the Heavy Current
Regulations, Section 107 -1-D1 or EN 60309-2.
Finland - Differences to IEC60950, Third Edition (1999)
6.1.2.2
The exclusions are applicable for PERMANENTLY
CONNECTED EQUIPMENT and PLUGGABLE EQUIPMENT TYPE B only.
UL International Demko A/S
N/A
Issue Date:
2003-09-25
Page 4 of 25
Report Reference #
E203413-A17-CB-1
IEC 60950
SubClause Difference + Test
Result - Remark
Verdict
Germany - Differences to IEC60950, Third Edition (1999)
1.7.12
Directions for use with rules to prevent certain
hazards for (among others) maintenance of the
technical labour equipment, also for imported
technical labour equipment shall be written in the
German language.
NOTE: Of this requirement, rules for use even only
by service personnel are not exempted.
N/A
H.a
a) A license is required by those who operate an Xray emission source
N/A
H.b
b) A license in accordance with Clause 1 is not
required by those who operate an X-ray emission
source on which the electron acceleration voltage
does not exceed 20 kV if:
N/A
1) The local dose rate at a distance of 0.1 m from
the surface does not exceed 1 µSv/h and
2) it is adequately indicated on the X-ray emission
source that
i) X-rays are generated and
ii) the electron acceleration voltage must not
exceed the maximum value stipulated by the
manufacturer or importer
UL International Demko A/S
Issue Date:
2003-09-25
Page 5 of 25
Report Reference #
E203413-A17-CB-1
IEC 60950
SubClause Difference + Test
H.c
Result - Remark
c) A license in accordance with Clause 1 is also not
required by persons who operate a X-ray emission
source on which the electron acceleration voltage
exceeds 20 kV if:
Verdict
N/A
1) The X-ray emission source has been granted a
type approval and
2) It is adequately indicated on the X-ray
emission source that
i) X-rays are generated
ii) the device stipulated by the manufacturer or
importer guarantees that the maximum permissible
local dose rate in accordance with the type
approval is not exceeded and
iii) the electron acceleration voltage not exceed
the maximum value stipulated by the manufacturer
or importer
H.d
d) Furthermore, a license in accordance with
Clause 1 is also not required by persons who
operate X-ray emission source on which the
electron acceleration voltage does not exceed 30
kV if:
1) the X-rays are generated only intrinsically
safety CRTs complying with Enclosure III, No. 6
2) the values stipulated in accordance with
Enclosure III, No. 6.2 are limited by technical
measured and specified in the device and
3) it is adequately indicated on the X-ray emission
source that the X-rays generated are adequately
screened by the intrinsically safe CRT.
UL International Demko A/S
N/A
Issue Date:
2003-09-25
Page 6 of 25
Report Reference #
E203413-A17-CB-1
IEC 60950
SubClause Difference + Test
Result - Remark
Verdict
Group - Differences to IEC60950, Third Edition (1999)
2.7.1
Replace the text of this Sub-Clause by:
Basic requirements
To protect against excessive current, short circuits
and earth faults in PRIMARY CIRCUITS, protective
devices shall be included either as integral parts of
the equipment or as parts of the building
installation, subject to the following, a), b), and c)
Pass
2.7.1.a
a).Except as detailed in b) and c), protective
devices necessary to comply with the requirements
of subclause 5.3 shall be Included as parts of the
equipment
N/A
2.7.1.b
b).For components in series with the mains input to
the equipment such as the supply cord, appliance
coupler, r.f.i. filter and switch, short circuit and
earth fault protection may be provided by protective
devices in the building installation.
Pass
2.7.1.c
c).It is permitted for PLUGGABLE EQUIPMENT
TYPE B or PERMANENTLY CONNECTED
EQUIPMENT, to rely on dedicated overcurrent and
short circuit protection in the building installation,
provided that the means of protection, e.g. fuses or
circuit breakers, is fully specified in the installation
instruction.
N/A
2.7.1.c
If reliance is placed on protection in the building
installation. the installation instructions shall so
state, except that for PLUGGABLE EQUIPMENT
TYPE A the building Installation shall be regarded
as providing protection in accordance with the
rating of the wall socket outlet.
N/A
2.7.2
This subclause has been declared 'void'
N/A
3.2.3
Delete NOTE 1, and in table 3A delete the conduit
sizes in parentheses.
N/A
3.2.5
Replace as follows:
N/A
"60245 IEC 53" by "H05 RR-F"
"60227 IEC 52" by "H03 VV-F or H03 VVH2-F"
"60227 IEC 53" by "H05 VV-F or H05 VVH2-F"
UL International Demko A/S
Issue Date:
2003-09-25
Page 7 of 25
Report Reference #
E203413-A17-CB-1
IEC 60950
SubClause Difference + Test
3.2.5
Result - Remark
In table 3B, replace the first four lines by the
following:
Verdict
N/A
Up to and including 6
0.75 1)
Over 6 up to and including 10
0.75 2) 1.0
Over 10 up to and including 16 1.0 3)
0.5
In the Conditions applicable to table 3B delete the
words "in some countries" in condition 1.
In NOTE 1, delete the second sentence.
3.3.4
In table 3D, delete the fourth line - conductor sizes
for 10 to 13 A. and replace with the following:
N/A
Over 10 up to & including 16
1.5 to 2.5
1.5 to by 4.
Delete the fifth line - conductor sizes for 13 to 16A.
4.3.13
Replace the second compliance paragraph by:
N/A
For equipment using LEDs or lasers, compliance is
checked according to EN 60825- 1
4.3.13
NOTE 1 - if equipment falling within the scope of
EN 60950 is inherently a class 1 laser product, i.e.
it contains no embedded laser or LED of a higher
class number, then a laser warning label or other
laser warning statement is not required (see 1.1 of
EN 60825-1).
N/A
Renumber the NOTE below the third compliance
paragraph as NOTE 2
H
Replace the last paragraph of this annex by:
N/A
At any point 10 cm from the surface of the
OPERATOR ACCESS AREA the dose rate shall
not exceed 1µSv/h (0.1 mR/h) (see note). Account
is taken of the background level.
Replace the NOTE as follows:
NOTE - These values appear in directive
96/29/Euratorm.
P
Replace the text of this annex by:
See annex ZA
UL International Demko A/S
Pass
Issue Date:
2003-09-25
Page 8 of 25
Report Reference #
E203413-A17-CB-1
IEC 60950
SubClause Difference + Test
Q
Result - Remark
Add the following notes for the standards indicated:
Verdict
Pass
IEC 60127 series NOTE. Harmonized as EN 60127
series (not modified)
IEC 60529 NOTE: Harmonized as EN 60529: 1991
(not modified)
IEC 61032 NOTE: Harmonized as EN 61032: 1998
(not modified)
Ireland - Differences to IEC60950, Third Edition (1999)
3.2.1
Apparatus which is fitted with a flexible cable or
cord and is designed to be connected to a mains
socket conforming to I.S. 411 by means of that
flexible cable or cord and plug, shall be fitted with a
13 A plug in accordance with Statutory Instrument
525:1997 - National Standards Authority of Ireland
(Section 28) (13 A Plugs and Conversion Adaptors
for Domestic Use) Regulations, 1997.
4.3.6
DIRECT PLUG-IN EQUIPMENT comply with
Statutory Instrument 526:1997 - National
Standards Authority of Ireland (Section 28)
(Electrical plugs, plug similar devices and sockets
for domestic use) Regulations, 1997.
N/A
Evaluate when national
evaluation
UL International Demko A/S
N/A
Issue Date:
2003-09-25
Page 9 of 25
Report Reference #
E203413-A17-CB-1
IEC 60950
SubClause Difference + Test
Result - Remark
Verdict
Japan - Differences to IEC60950, Third Edition (1999)
1.2.4.101
Addition:
Definition of CLASS 0I EQUIPMENT
N/A
1.2.12.1
Replacement:
FLAMMABILITY CLASSIFICATION OF
MATERIALS:
"The recognition of the burning behaviour of
materials and their ability to extinguish if ignited.
Materials are classified as in 1.2.12.2 to 1.2.12.9,
and 1.2.12.101 when tested in accordance with
annex A"
N/A
1.2.12.101 Addition:
Definition of VTM CLASS MATERIAL
N/A
1.7.101
Addition:Marking for CLASS 0I EQUIPMENT
The following instruction is indicated on the visible
place of the mains plug or the main body:
"Provide an earthing connection"
N/A
1.7.101
The following instruction is indicated on the visible
place on the main body or written in the operating
instructions:
"Provide an earthing connection before the mains
plug is connected to the mains. And, when
disconnecting the earthing connection, be sure to
disconnect after pulling out the mains plug from the
mains."
N/A
2.1.1.1
Replace:
"IEC 60083" by "IEC 60083 or JIS C 8303"
in 2.1.1.1 b)
N/A
2.6.3.1
Add the following after 1st paragraph:
"This also applies to the conductor of lead wire for
protective earthing of CLASS 0I EQUIPMENT"
N/A
2.6.4.1
Replace 2nd sentence in 1st paragraph:
"For CLASS I EQUIPMENT with a DETACHABLE
POWER SUPPLY CORD, the earthing terminal in
the appliance inlet is regarded as the main
protective earthing terminal"
N/A
2.6.5.4
Replace 1st sentence:
"Protective earthing connections of CLASS I
EQUIPMENT shall make earlier and break later
than the supply connections in each of the
following:"
N/A
UL International Demko A/S
Issue Date:
2003-09-25
Page 10 of 25
Report Reference #
E203413-A17-CB-1
IEC 60950
SubClause Difference + Test
Result - Remark
Verdict
2.6.101
Addition:Earthing of CLASS 0I EQUIPMENT
Plugs with a lead wire for earthing not used for
equipment having a rated voltage exceeding 150 V
N/A
2.6.101
For plugs with a lead wire for earthing, the lead
wire is not earthed by a clip
N/A
2.6.101
CLASS 0I EQUIPMENT provided with an earthing
terminal or lead wire for earthing in the external
where easily visible
N/A
3.2.5
Delete the following statement from a note 1 in
Table 3B:
"For RATED CURRENT up to 3A, a nominal
cross-sectional area of 0.5 mm2 is permitted in
some countries provided that the length of the cord
does not exceed 2 m"
N/A
4.2.8
Add the following informative remark after the last
sentence:
"IEC 61965 is also applicable instead of IEC
60065"
N/A
4.5.1
Add the following to note 5) of Table 4A, Part 2:
"With regard to Table 4A, insulating materials
complying with Japanese requirements (refer to
Japanese differences for IEC 60335-1 3rd Edition
in CB Bulletin 101B) are also acceptable"
N/A
4.5.1
Add a note reference 7) to "50", in the right column
of Table 4A, Part 1 and add a note 7 to Table 4A,
Part 2 as follows:
"7) This value apply only to wiring or cords
complying with relevant IEC standards.
Others comply with Japanese requirements (refer
to Japanese differences for
IEC 60335-1 3rd Edition in CB Bulletin 101B)"
N/A
4.7.3.2
Add the following in 7th paragraph:
"- for thin materials, e.g., flexible printed boards,
etc., used inside equipment, be of FLAMMABILITY
CLASS VTM-2 or better"
N/A
5.1.6
Replace Table 5A to include maximum TOUCH
CURRENT values for CLASS 0I EQUIPMENT
N/A
5.3.8.2
Replace 3rd Item as follows:
"- BASIC INSULATION between the PRIMARY
CIRCUIT and accessible conductive parts of
CLASS I or 0I EQUIPMENT;"
N/A
UL International Demko A/S
Issue Date:
2003-09-25
Page 11 of 25
Report Reference #
E203413-A17-CB-1
IEC 60950
SubClause Difference + Test
Result - Remark
Verdict
Annex A
Add the subclause A.101titled:
"Flammability tests for classifying materials VTM"
and the following:
"Thin sheet materials shall comply with ISO 9773"
N/A
Annex G
Add to the Note for Table G.1.
"2. In Japan, MAINS TRANSIENT VOLTAGE for
equipment with a Nominal AC MAINS SUPPLY
VOLTAGE of 100V is to be decided based on the
column where Nominal AC MAINS SUPPLY
VOLTAGE in Table G.1 is 150V"
N/A
Annex P
Add:
"IEC 61965:2000, Mechanical Safety for Cathode
Ray Tubes"
N/A
Annex U
Replace 2nd paragraph as follows:
"This annex covers to round winding wires having
diameters between 0.05 mm and 5.00 mm"
N/A
U.2.1
Replacement:Electric strength
"The test sample is prepared per IEC 608515:1997, 4.4.1 (for a twisted pair and subjected to
the test of 5.2.2, with a test voltage not less than
twice the appropriate voltage in table 5B (see
5.2.2) of this standard. However, the minimum
values shall be as follows:
- for BASIC INSULATION or SUPPLEMENTARY
INSULATION, 3000 V, or;
- for REINFORCED INSULATION, 6000 V"
N/A
U.2.2
Replacement:Flexibility and adherence
Test 8 of IEC 60851-3:1996, 5.1.1, using the
mandrel diameter of Table U.1 (mm)
N/A
U.2.2
Test voltage not less than twice the appropriate
voltage in table 5B (see 5.2.2) of this standard and
not less than:
- 1500 V for BASIC INSULATION or
SUPPLEMENTARY INSULATION, or;
- 3000 V for REINFORCED INSULATION
N/A
UL International Demko A/S
Issue Date:
2003-09-25
Page 12 of 25
Report Reference #
E203413-A17-CB-1
IEC 60950
SubClause Difference + Test
Result - Remark
Verdict
Norway - Differences to IEC60950, Third Edition (1999)
1.5.8
Due to the IT power system used (see annex V,
figure V.7), capacitors are required to be rated for
the applicable phase-to-phase voltage ( 230 V).
N/A
1.7.2
CLASS I PLUGGABLE EQUIPMENT TYPE A
intended for connection to other equipment or a
communication network where safety relies on
connection to protective earth, require a marking
stating that the equipment must be connected to an
earthed mains socket-outlet.
N/A
2.2.4
Requirements according to sub-clauses 1.7.2 and
6.1.2.1 apply for this clause.
N/A
2.3.2
Requirements according to sub-clause 6.1.2.1
apply for this clause.
N/A
2.3.3
Requirements according to sub-clause 6.1.2.1
apply for this clause.
N/A
2.3.4
Requirements according to sub-clauses 1.7.2 and
6.1.2.1 apply for this clause.
N/A
2.10.3.1
Due to the IT power distribution system used (see
annex V, figure V.7), the A.C. MAINS SUPPLY
voltage is considered to be equal to the line-to-line
voltage, and will remain at 230 V in case of a single
earth fault.
N/A
6.1.2.1
Note 2.
N/A
Add the following text between the first and second
paragraph:
If this insulation is solid, including insulation
forming part of a component, it shall at least consist
of either
- two layers of thin sheet material, each of which
shall pass the electric strength test below, or
- one layer having a distance through insulation of
at least 0.4 mm, which shall pass the electric
strength test below.
UL International Demko A/S
Issue Date:
2003-09-25
Page 13 of 25
Report Reference #
E203413-A17-CB-1
IEC 60950
SubClause Difference + Test
6.1.2.1
Result - Remark
If this insulation forms part of a semiconductor
component e.g. an optocoupler, there is no
distance through insulation requirement for the
insulation consisting of an insulating compound
completely filling the casing, so that CLEARANCES
and CREEPAGE DISTANCES do not exist, if the
component passes the electric strength test in
accordance with the compliance clause below and
in addition:
Verdict
N/A
- passes the tests and inspection criteria of 2.10.8
with an electric strength test of 1.5 kV multiplied by
1.6 (the electric strength test of 2.10.7 shall be
performed using 1.5 kV): and
- is subject to ROUTINE TESTING for electric
strength during manufacturing, using a test voltage
of 1.5 kV.
6.1.2.1
It is permitted to bridge this insulation with a
capacitor complying with EN 132400:1994,
subclass Y2.
N/A
6.1.2.2
The exclusions are applicable for PERMANENTLY
CONNECTED EQUIPMENT and PLUGGABLE EQUIPMENT TYPE B only.
N/A
G.2
Due to the IT power distribution system used (see
annex V, figure V.7), the A.C. MAINS SUPPLY
voltage is considered to be equal to the line-to-line
voltage, and will remain at 230 V in case of a single
earth fault.
N/A
UL International Demko A/S
Issue Date:
2003-09-25
Page 14 of 25
Report Reference #
E203413-A17-CB-1
IEC 60950
SubClause Difference + Test
Result - Remark
Verdict
Spain - Differences to IEC60950, Third Edition (1999)
3.2.1
Supply cords of single-phase equipment having a
rated current not exceeding:
- 2.5 A shall be provided with a plug according to
UNE EN 50075:1993
- 10 A shall be provided with a plug according to
UNE 20315:1994
CLASS I EQUIPMENT provided with socket-outlets
with earth contacts, or which are intended to be
used in locations where protection against indirect
contact is required according to the wiring rules,
shall be provided with a plug in accordance with
UNE 20315:1994
If poly-phase equipment is provided with a supply
cord with a plug, this plug shall be in accordance
with the UNE-EN 60309-2.
UL International Demko A/S
N/A
Issue Date:
2003-09-25
Page 15 of 25
Report Reference #
E203413-A17-CB-1
IEC 60950
SubClause Difference + Test
Result - Remark
Verdict
Sweden - Differences to IEC60950, Third Edition (1999)
1.5.1
Add the following:
NOTE: Switches containing mercury such as
thermostats, relays and level controllers are not
allowed.
N/A
1.7.2
If the separation between the mains and a SELV
terminal relies upon connection to safety earth, the
apparatus shall have a marking stating that it must
be connected to an earthed mains socket -outlet.
The marking text shall be in Swedish and as
follows:
"Apparaten skall anslutas till jordat uttag när den
ansluts till ett nätverk".
N/A
6.1.2.1
Note 1.
Add the following text between the first and second
paragraph:
If this insulation is solid, including insulation
forming part of a component, it shall at least consist
of either
- two layers of thin sheet material, each of which
shall pass the electric strength test below, or
- one layer having a distance through insulation of
at least 0.4 mm, which shall pass the electric
strength test below.
N/A
6.1.2.1
If this insulation forms part of a semiconductor
component e.g. an optocoupler, there is no
distance through insulation requirement for the
insulation consisting of an insulating compound
completely filling the casing, so that CLEARANCES
and CREEPAGE DISTANCES do not exist, if the
component passes the electric strength test in
accordance with the compliance clause below and
in addition:
N/A
- passes the tests and inspection criteria of 2.10.8
with an electric strength test of 1.5 kV multiplied by
1.6 (the electric strength test of 2.10.7 shall be
performed using 1.5 kV): and
- is subject to ROUTINE TESTING for electric
strength during manufacturing, using a test voltage
of 1.5 kV.
6.1.2.1
It is permitted to bridge this insulation with a
capacitor complying with EN 132400:1994,
subclass Y2.
UL International Demko A/S
N/A
Issue Date:
2003-09-25
Page 16 of 25
Report Reference #
E203413-A17-CB-1
IEC 60950
SubClause Difference + Test
6.1.2.2
Result - Remark
The exclusions are applicable for PERMANENTLY
CONNECTED EQUIPMENT and PLUGGABLE EQUIPMENT TYPE B only.
Verdict
N/A
Switzerland - Differences to IEC60950, Third Edition (1999)
1.5.1
Add the following:
N/A
NOTE: Switches containing mercury such as
thermostats, relays and level controllers are not
allowed.
1.7.15
Annex 4.10 of SR 814.013 (Ordinance on
environmentally hazardous substances) applies for
batteries.
N/A
3.2.1
Supply cords of equipment having a rated current
not exceeding 10 A shall be provided with a plug
complying with SEV 1011 or IEC 884-1 and one of
the following dimension sheets:
N/A
SEV 6532-2.1991 Plug Type 15
250/400 V,10 A
SEV 6533-2.1991 Plug Type 11
250 V,10 A
SEV 6534-2.1991 Plug Type 12
250 V,10 A
3P+N+PE
L+N
L+N+PE
EN 60309 applies for plugs for currents exceeding
10 A.
6.1
Protective means in the equipment shall not
prevent transient surge protection in the
telecommunication network from operating properly
(d.c. spark-over voltage of the surge suppressor
installed in the telecommunication network: approx.
245 V).
UL International Demko A/S
N/A
Issue Date:
2003-09-25
Page 17 of 25
Report Reference #
E203413-A17-CB-1
IEC 60950
SubClause Difference + Test
Result - Remark
Verdict
USA / Canada - Differences to IEC60950, Third Edition (1999)
1.1
Equipment able to be installed in accordance with
the National Electrical Code ANSI/NFPA 70 and
the Canadian Electrical Code, Part1.
Pass
1.1.1
Equipment able to be installed in accordance with
ANSI/NFPA 75 and NEC Art. 645 unless intended
for use outside of computer room and provided with
such instructions
Pass
1.1.2
Equipment in wire-line communication facilities
serving high-voltage electric power stations
operating at greater than 1kV are excluded
N/A
1.1.2
Special requirements apply to equipment intended
for use outdoors
N/A
1.5.1
All IEC standards for components identified in
Annex P.1 replaced by the relevant requirements of
CSA and UL component standards in Annex P.1
Pass
1.5.1
All IEC standards for components identified in
Annex P.2 alternatively satisfied by the relevant
requirements of CSA and UL component standards
in Annex P.2
Pass
1.5.5
Interconnecting cables acceptable for the
application regarding voltage, current, temperature,
flammability, mechanical serviceability and the like
Pass
1.5.5
For other than limited power and TNV circuits, the
type of output circuit identified for output connector
N/A
1.5.5
External cable assemblies which exceed 3.05 m in
length to be types specified in the NEC and CEC
N/A
1.5.5
Detachable external interconnecting cables 3.05 m
or less in length and provided with equipment
marked to identify the responsible organization and
the designation for the cable
N/A
1.5.5
Building wiring and cable for use in ducts, plenums
and other air handling space subject to special
requirements and excluded from scope
N/A
1.5.5
Telephone line and extension cords and the like
comply with UL 1863 and CSA C22.2 No. 233
N/A
1.7.1
Special marking format for equipment intended for
use on a supply system with an earthed neutral
and more than one phase conductor
N/A
1.7.1
Equipment voltage rating not higher than rating of
the plug except under special conditions
N/A
UL International Demko A/S
Issue Date:
2003-09-25
Page 18 of 25
Report Reference #
E203413-A17-CB-1
IEC 60950
SubClause Difference + Test
Result - Remark
Verdict
1.7.2
Wiring terminals supplying Class 2 outputs marked
with voltage rating and "Class 2" or equivalent
N/A
1.7.6
Special fuse replacement marking for operator
accessible fuses
N/A
1.7.6
Lamp replacement information indicated on
lampholder in operator access area
N/A
1.7.7
Identification of terminal connection of the
equipment earthing conductor
N/A
2.1.1
Screw shell of Edison-base lampholder tied to the
neutral conductor
N/A
2.1.1.1
Bare TNV conductive parts in the interior of
equipment normally protected against contact by a
cover intended for occasional removal are exempt
provided instructions include directions for
disconnection of TNV prior to removal of the cover
N/A
2.3.1.b
Other telecommunication signaling systems (e.g.,
message waiting) than described in 2.3.1(b) are
subject to M.4.
N/A
2.3.1.b
For TNV-2 and TNV -3 circuits with other than
ringing signals and with voltages exceeding 42.4
Vp or 60 V d.c., the maximum current limit through
the 2000 Ohm resistor with loads disconnected is
7.1 mA peak or 30 mA d.c. under normal conditions
N/A
2.3.1.b
Limits for measurements across 5000 Ohm resistor
in the event of a single fault are replaced after 200
ms with the limits of M.3.1.4
N/A
2.3.2
Enamel coating on signal transformer winding wire
allowed as an alternative to Basic insulation in
specific telecommunication applications when
subjected to special construction requirements and
routine testing
N/A
2.5
Overcurrent protection device required for Class 2
and Class 3 limiting in accordance with the NEC, or
the Limited Power Source definition, not
interchangeable with devices of higher ratings if
operator replaceable
N/A
2.5
VA for limited power source measured after 60 s of
operation
N/A
2.6
Protective earthing terms applied per CEC, Part 1,
Sec. 0 and NEC Art. 100
Class II equipment
UL International Demko A/S
N/A
Issue Date:
2003-09-25
Page 19 of 25
Report Reference #
E203413-A17-CB-1
IEC 60950
SubClause Difference + Test
Result - Remark
Verdict
2.6
Units having receptacles for output a.c. power
connectors which are generated from an internal
separately derived source have the grounded
circuit conductor suitably bonded to earth
N/A
2.6.3.3
Capacity of connection between earthing terminal
and parts required to be earthed subject to special
conditions based on the current rating of the circuit
N/A
2.6.3.3
Protective bonding conductors and their terminals
of non-standard constructions (e.g. PWB traces)
evaluated to limited short-circuit test of CSA C22.2
No.4
N/A
2.6.4.1
Field wiring terminals for earthing conductors must
be suitable for wire sizes (gauge) used in US and
Canada
N/A
2.7.1
Data for selection of special external branch circuit
overcurrent devices marked on the appliance
N/A
2.7.1
Standard supply outlets protected by overcurrent
device in accordance with the NEC, and CEC, Part
1
N/A
2.7.1
Overcurrent protection for individual transformers
that distribute power to other units over branch
circuit wiring
N/A
2.7.1
Additional requirements for overcurrent protection
apply to equipment provided with panelboards
N/A
2.7.1
Non -motor-operated equipment requiring special
overcurrent protective device marked with device
rating
N/A
2.10.5.4
Multi-layer winding wire subject to UL wire
requirements in addition to 2.10.5.4 and Annex U
Pass
3.1.1
Permissible combinations of internal wiring/external
cable sizes for overcurrent and short circuit
protection
3.1.1
All interconnecting cables protected against
overcurrent and short circuit
Pass
3.2
Wiring methods permit connection of equipment to
primary power supply in accordance with the NEC
and CEC, Part 1
Pass
3.2.1
Permitted use for flexible cords and plugs
N/A
3.2.1
Flexible cords provided with attachment plug rated
125% of equipment current rating
N/A
UL International Demko A/S
N/A
Issue Date:
2003-09-25
Page 20 of 25
Report Reference #
E203413-A17-CB-1
IEC 60950
SubClause Difference + Test
Result - Remark
Verdict
3.2.1
Class II equipment provided with 15 or 20 A
standard supply outlets, Edison-base lampholders
or single pole disconnect device provided with a
polarized type attachment plug
N/A
3.2.3
Permanently connected equipment has provision
for connecting and securing a field wiring system
(i.e. conduit, or leads etc.) per the NEC and CEC,
Part 1
N/A
3.2.3
Permanently connected equipment may have
terminals or leads not smaller than No. 18 AWG
(0.82 mm²) and not less than 152 mm in length for
connection of field installed wiring
N/A
3.2.3
If supply wires exceed 60 °C, marking indicates
use of 75 °C or 90 °C wiring for supply connection
as appropriate
N/A
3.2.3
Equipment intended solely for installation in
Restricted Access Locations using low voltage d.c.
systems may not need provision for connecting and
securing a field wiring system. A method of
securing wiring or instructions must be provided to
ensure the wiring is protected from abuse
N/A
3.2.3
Equipment compatible with suitable trade sizes of
conduits and cables
N/A
3.2.5
Length of power supply cord 1.5 to 4.5 m unless
shorter length used when intended for a special
installation
N/A
3.2.5
Conductors in power supply cords sized according
to NEC and CEC, Part I
N/A
3.2.5
Power supply cords and cord sets incorporate
flexible cords suitable for the particular application
N/A
3.2.6
Strain relief provided for non-detachable
interconnecting cables not supplied by a limited
power source
N/A
3.2.9
Adequate wire bending space and volume of field
wiring compartment to properly make the field
connections
N/A
3.3
Field wiring terminals provided for interconnection
of units for other then LPS or Class 2 circuits also
comply with 3.3
N/A
3.3
Interconnection of units by LPS or Class 2
conductors may have field wiring connectors other
than those specified in 3.3 if wiring is reliably
separated
N/A
UL International Demko A/S
Issue Date:
2003-09-25
Page 21 of 25
Report Reference #
E203413-A17-CB-1
IEC 60950
SubClause Difference + Test
Result - Remark
Verdict
3.3.1
Terminals for the connection of neutral conductor
identified by a distinctive white marking or other
equally effective means
N/A
3.3.3
Wire binding screw terminal permitted for
connection of No. 10 AWG (5.3 mm²) or smaller
conductor if provided with upturned lugs, cupped
washer or equivalent retention
N/A
3.3.4
Terminals suitable to accept wire sizes (gauge)
used in the U.S. and Canada
N/A
3.3.4
Terminals accept current -carrying conductors rated
125% of the equipment current rating
N/A
3.3.6
Field wiring terminals marked to indicate the
material(s) of the conductor appropriate for the
terminals used
N/A
3.3.6
Connection of an aluminum conductor not
permitted to terminal for equipment earthing
conductor
N/A
3.3.6
Field wiring connections made through the use of
suitable pressure connectors (including set screw
type), solder lugs or splices to flexible leads
N/A
3.3.8
Connectors and field wiring terminals involving
external Class 2 or Class 3 circuits provided with
marking indicating minimum Class of wiring to be
used
N/A
3.3.8
Marking located adjacent to terminals and visible
during wiring
N/A
3.4.2
Separate motor control device(s) required for cordconnected equipment rated more than 12 A, or with
motor rated more than 1/3 hp or more than 120 V
N/A
3.4.8
Vertically mounted disconnect devices, oriented so
up position of handle is "on"
N/A
3.4.10
For computer-room applications, equipment with
battery systems capable of supplying 750 VA for 5
min require battery disconnect means
N/A
3.6
Connections to a centralized DC power system
comply with requirements for branch circuits in
Sub-clause 3.2
N/A
3.6
Earthing of d.c. powered equipment provided
N/A
3.6
Overcurrent and earth fault protection in
accordance with 2.7 either provided in equipment
or as part of building installation
N/A
UL International Demko A/S
Issue Date:
2003-09-25
Page 22 of 25
Report Reference #
E203413-A17-CB-1
IEC 60950
SubClause Difference + Test
Result - Remark
Verdict
3.6
Equipment with earthed terminal (terminal for the
grounded conductor) of power source connected to
frame of the unit provided with special instructions
and provision for earthing
N/A
3.6
Equipment with means for connecting supply to
earthing electrode conductor has no switches or
protective devices between supply connection and
earthing electrode connection
N/A
3.6
Special markings and instructions for equipment
with provisions to connect earthed conductor of a
DC supply circuit to earthing conductor at the
equipment
N/A
3.6
Special markings and instructions for equipment
with earthed conductor of a DC supply circuit
connected to the earthing conductor at the
equipment
N/A
3.6
Terminals and leads provided for permanent
connection of DC powered equipment to supply
marked to indicate polarity if reverse polarity may
result in a hazard
N/A
4.2.8.1
Special opening restrictions for enclosures around
CRTs with face dimension of 160 mm or more
N/A
4.2.9
Compartment housing high-pressure lamp marked
to indicate risk of explosion
N/A
4.3.2
Loading test for equipment with handle(s) used to
support more than 9 kg tested at four times the
weight of the unit
N/A
4.3.6
In addition to the IEC requirements, Direct Plug-in
Equipment comply with UL 1310 or CSA 223
mechanical assembly requirements
Pass
4.3.12
The maximum quantity of flammable liquid stored
in equipment comply with ANSI/NFPA 30(Table
NAE. 7)
N/A
4.3.12
Equipment using replenishable liquids marked to
indicate type of liquid to be used
N/A
4.3.13
Equipment which produces x-radiation and does
not comply with 4.3.12 under all conditions of
servicing marked to indicate the presence of
radiation where readily visible
N/A
4.3.13
Requirements contained in the applicable national
codes and regulations apply to lasers (21 CFR
1040 and REDR C1370)
N/A
UL International Demko A/S
Issue Date:
2003-09-25
Page 23 of 25
Report Reference #
E203413-A17-CB-1
IEC 60950
SubClause Difference + Test
Result - Remark
Verdict
4.7.1
Automated information storage equipment intended
to contain more than 0.76 mm³ of combustible
media requires provision for automatic sprinklers or
a gaseous agent extinguishing system
N/A
4.7.3
Equipment for use in environmental air space other
than ducts or plenums provided with metal
enclosure or with non-metallic enclosure having
adequate fire-resistance and low smoke producing
characteristics
N/A
4.7.3
Low smoke-producing characteristics evaluated
according to UL 2043
N/A
4.7.3
Equipment for installation in space used for
environmental air as described in Sec. 300-22(c) of
the NEC provided with instructions indicating
suitability for installation in such locations
N/A
4.7.3.1
Flame spread rating for external surface of
combustible material with exposed area greater
than 0.93 m² or a single dimension greater than 1.8
m; 50 or less for computer room applications or
200 or less for other applications
N/A
4.7.3.4
Wire marked "VW-1" or "FT-1" considered
equivalent
5.1.8.1.1
Touch current due to ringing voltage for equipment
containing telecommunication network leads
N/A
5.1.8.2
When multiple ports receive ringing voltage,
simulated ringing applied to 3 % if ports in excess
of 3
N/A
5.1.8.2
Special earthing provisions and instructions for
equipment with high touch current due to
telecommunication network connections
N/A
5.3.6
Overloading of SELV connectors and print ed wiring See appended table 5.3.
board receptacles accessible to the operator
5.3.6
Tests interrupted by opening of a component
repeated two additional times
N/A
5.3.8.1
Test interrupted by opening of wire or trace
continued by shorting gap
N/A
6
Specialized instructions, as appropriate, provided
for equipment which may be connected to a
telecommunications network
N/A
6
Marking identifying function of telecommunication
type connectors not used for connection to a
telecommunication network
N/A
VW-1 or FT-1 cord used.
UL International Demko A/S
Pass
Pass
Issue Date:
2003-09-25
Page 24 of 25
Report Reference #
E203413-A17-CB-1
IEC 60950
SubClause Difference + Test
Result - Remark
Verdict
6.2.1
Special requirements for enameled wiring used as
electrical separation provided between parts
connected to telecommunication network and
telecommunication circuitry intentionally isolated
from network
N/A
6.2.1
Digital line termination equipment (e.g., NCTE)
subject to separation requirements.
N/A
6.3
Equipment remotely powered over
telecommunication wiring systems provided with
specialized markings adjacent to the connection
N/A
6.3
Overcurrent protection incorporated into equipment
to provide power over telecommunication wiring
system not interchangeable with devices of higher
ratings if operator replaceable
N/A
6.4
Additional requirements for equipment intended for
connection to a telecommunication network using
cable subject to overvoltage from power line
failures (Fig. 6C)
N/A
6.4
Where 26 AWG line cord required by Fig. 6C,
either the cord is provided with the equipment or
described in the safety instructions
N/A
6.5
Acoustic pressure from an ear piece less than 136
dBA for short duration disturbances, and less than
125 dBA for handsets, 118 dBA for headsets, and
121 dBA for insert earphones, for long duration
disturbances
N/A
Annex NAB Equipment intended for connection to centralized
d.c. power systems is required to comply with
special earthing, wiring, and supply voltage
tolerance requirements
N/A
Annex
NAC
Equipment intended for use with a generic
secondary protector marked with suitable
instructions
N/A
Annex
NAC
Equipment intended for use with a specific primary
or secondary protector marked with suitable
instructions
N/A
H
Ionizing radiation measurements are made under
single fault conditions in accordance with the
requirements of the Code of Federal Regulations
21 CFR 1020 and the Canadian Radiation Emitting
Devices Act, REDR C1370
N/A
M.2
Continuous ringing signals evaluated to Method A
subjected to special accessibility considerations
N/A
UL International Demko A/S
Issue Date:
2003-09-25
Page 25 of 25
Report Reference #
E203413-A17-CB-1
IEC 60950
SubClause Difference + Test
M.4
Result - Remark
Special requirements for message waiting and
similar telecommunications signals
UL International Demko A/S
Verdict
N/A
Issue Date:
2003-09-25
Page 1
Report Reference #
Enclosure
Photographs
(Total 6 Pages including this Cover Page)
Supplement Id
Description
3-01
Top View
3-02
Bottom View with US/Canada and Japan plug
3-03
Interior View
3-04
Interior view with insulation sheet and shield
3-05
Interior bottom view
3-06
Bottom view with euro plug
UL International Demko A/S
E203413-A17-CB-1
Issue Date:
2003-09-25
Page 2
Report Reference #
UL International Demko A/S
E203413-A17-CB-1
Issue Date:
2003-09-25
Page 3
Report Reference #
UL International Demko A/S
E203413-A17-CB-1
Issue Date:
2003-09-25
Page 4
Report Reference #
UL International Demko A/S
E203413-A17-CB-1
Issue Date:
2003-09-25
Page 5
Report Reference #
UL International Demko A/S
E203413-A17-CB-1
Issue Date:
2003-09-25
Page 6
Report Reference #
UL International Demko A/S
E203413-A17-CB-1
Issue Date:
2003-09-25
Page 7
Report Reference #
UL International Demko A/S
E203413-A17-CB-1
Issue Date:
2003-09-25
Page 1
Report Reference #
Enclosure
Diagrams
(Total 6 Pages including this Cover Page)
Supplement Id
Description
4-01
Transformer (T1)
4-02
Insulation sheet and Shield
UL International Demko A/S
E203413-A17-CB-1
Issue Date:
2003-09-25
Page 2
Report Reference #
UL International Demko A/S
E203413-A17-CB-1
Issue Date:
2003-09-25
Page 3
Report Reference #
UL International Demko A/S
E203413-A17-CB-1
Issue Date:
2003-09-25
Page 4
Report Reference #
UL International Demko A/S
E203413-A17-CB-1
Issue Date:
2003-09-25
Page 5
Report Reference #
UL International Demko A/S
E203413-A17-CB-1
Issue Date:
2003-09-25
Page 6
Report Reference #
UL International Demko A/S
E203413-A17-CB-1
Issue Date:
2003-09-25
Page 1
Report Reference #
Enclosure
Schematics + PWB
(Total 8 Pages including this Cover Page)
Supplement Id
Description
5-01
PWB layout
UL International Demko A/S
E203413-A17-CB-1
Issue Date:
2003-09-25
Page 2
Report Reference #
UL International Demko A/S
E203413-A17-CB-1
Issue Date:
2003-09-25
Page 3
Report Reference #
UL International Demko A/S
E203413-A17-CB-1
Issue Date:
2003-09-25
Page 4
Report Reference #
UL International Demko A/S
E203413-A17-CB-1
Issue Date:
2003-09-25
Page 5
Report Reference #
UL International Demko A/S
E203413-A17-CB-1
Issue Date:
2003-09-25
Page 6
Report Reference #
UL International Demko A/S
E203413-A17-CB-1
Issue Date:
2003-09-25
Page 7
Report Reference #
UL International Demko A/S
E203413-A17-CB-1
Issue Date:
2003-09-25
Page 8
Report Reference #
UL International Demko A/S
E203413-A17-CB-1
Issue Date:
2003-09-25
Page 1
Report Reference #
Enclosure
Miscellaneous
(Total 2 Pages including this Cover Page)
Supplement Id
7-01
Description
Label
UL International Demko A/S
E203413-A17-CB-1
Issue Date:
2003-09-25
Page 2
Report Reference #
UL International Demko A/S
E203413-A17-CB-1
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement