Yale Electric Hoist Operating & Maintenance Instructions

OPERATING &

MAINTENANCE

INSTRUCTIONS

WITH PARTS LIST

Publication Part No. 117404-21

Published December 2006

KELC

Electric

Hoists

For Capacities:

¼, ½, 1, 2, & 3 Ton

IMPORTANT - CAUTION

To safeguard against the possibility of personal injury or property damage, follow the recommendations and instructions of this manual. This manual contains important information for the correct installation, operation and maintenance of this equipment. All persons involved in the installation, operation and maintenance of this equipment should be thoroughly familiar with the contents of this manual. Keep this manual for reference and further use.

WARNING

To prevent personal injury, do not use the equipment shown in this manual to lift, support or otherwise transport people, or to suspend unattended loads over people.

FOREWORD

This book contains important information to help you install, operate, maintain and service your new Electric Hoist. We recommend that you study its content thoroughly before putting your hoist into use. Then, thru proper installation, application of correct operating procedures, and by practicing the recommended maintenance suggestions you will be assured maximum lifting service from the hoist.

The “Accident Prevention Manual for Industrial Operations’ (8th Edition) by the National Safety Council states:

“Employees who work near cranes or assist in hooking on or arranging loads should be instructed to keep out from under loads. Supervisors should watch closely to see that this rule is strictly followed.

Complete inspection, maintenance and overhaul service is available for

Yale Electric Hoists at Authorized Repair Stations. All are staffed by qualified factory-trained service men; have authorized testing equipment; and stock a complete inventory of factory approved Yale replacement parts.

From a safety standpoint, one factor is paramount: conduct all lifting operations in such a manner that if there were an equipment failure, no personnel would be injured. This means keep out from under raised loads!”

Complete replacement parts information is given in Section IX. It will likely be a long time before parts information is needed, therefore, after you completely familiarize yourself with operation and preventive maintenance procedures, we suggest that this instruction and parts manual be carefully filed for future reference.

THE INFORMATION CONTAINED IN THIS MANUAL IS FOR

INFORMATIONAL PURPOSES ONLY AND YALE HOISTS DOES NOT

WARRANT OR OTHERWISE GUARANTEE (IMPLIEDLY OR

EXPRESSLY) ANYTHING OTHER THAN THE COMPONENTS THAT

YALE MANUFACTURES AND ASSUMES NO LEGAL RESPONSIBILITY

(INCLUDING, BUT NOT LIMITED TO CONSEQUENTIAL DAMAGES)

FOR INFORMATION CONTAINED IN THIS MANUAL.

Notice: Use only factory approved Yale replacement parts, available from

Authorized Repair Stations or Yale Hoist Distributors.

INDEX

SECTION I GENERAL DESCRIPTION ........................................................................................................................................................ Page

Paragraph 1-1 General ................................................................................................................................................................................... 3

Paragraph 1-2 Hoist Service Classification .................................................................................................................................................. 3

Paragraph 1-3 Basic Construction ................................................................................................................................................................. 3

Paragraph 1-4 Differences Between Models and Sizes ............................................................................................................................... 4

Paragraph 1-5 Overload Clutch ..................................................................................................................................................................... 4

SECTION II INSTALLATION

Paragraph 2-1 General ................................................................................................................................................................................... 4

Paragraph 2-2 Installation .............................................................................................................................................................................. 4

Paragraph 2-3 Pre-Installation Checks .......................................................................................................................................................... 5

Paragraph 2-4 Connecting Hoist to Electrical Service ................................................................................................................................. 5

Paragraph 2-5 Electronic Adjustable Limit Switch ........................................................................................................................................ 5

SECTION III OPERATION

Paragraph 3-1 General ................................................................................................................................................................................... 6

Paragraph 3-2 Operating Hoist ...................................................................................................................................................................... 6

Paragraph 3-3 Pulling and Rotating Hoist and Load .................................................................................................................................... 6

Paragraph 3-4 Upper and Lower Limit Stops ............................................................................................................................................... 6

Paragraph 3-5 Overload Clutch Operations .................................................................................................................................................. 7

Paragraph 3-6 Operating Precautions ........................................................................................................................................................... 7

SECTION IV LUBRICATION

Paragraph 4-1 General ................................................................................................................................................................................... 8

Paragraph 4-2 Change Gear Case Oil .......................................................................................................................................................... 8

Paragraph 4-3 Lubricate Load Chain ............................................................................................................................................................ 8

Paragraph 4-4 Lubricate Upper Hook and Lower Block Assembly ............................................................................................................. 9

Paragraph 4-5 Lubricate Limit Lever Control Shaft and Gears ................................................................................................................... 9

SECTION V MAINTENANCE

Paragraph 5-1 General ....................................................................................................................................................................................... 9

Paragraph 5-2 Thirty-Day Inspection ................................................................................................................................................................ 9

Paragraph 5-3 Six-Month Inspection ............................................................................................................................................................... 12

Paragraph 5-4 Inspection 5000 Hour or Five Year ......................................................................................................................................... 12

SECTION VI TROUBLE SHOOTING CHART ............................................................................................................................................... 13-14

SECTION VII DISASSEMBLY AND REASSEMBLY

Paragraph 7-1 General ................................................................................................................................................................................. 14

Paragraph 7-2 Disassembly of Hoist Into Subassemblies ......................................................................................................................... 15

Paragraph 7-3 Rebuild of Hoist Frame, Sprocket Gear, Sprocket Shaft and Chain Guide ..................................................................... 17

Paragraph 7-4 Rebuild of Load Brake and Overload Clutch Assembly .................................................................................................... 20

Paragraph 7-4a Overload Clutch without Load Brake .................................................................................................................................. 22

Paragraph 7-5 Rebuild of Lower Block and Load Chain Assembly .......................................................................................................... 22

Paragraph 7-6 Rebuild of Electrical Controls and Gear Case Cover Subassembly ................................................................................ 23

Paragraph 7-7 Rebuild of Push Button Station and Conductor Cable Assembly .................................................................................... 23

Paragraph 7-8 Rebuild of Contactor Assembly (Push Button Models) ..................................................................................................... 24

Paragraph 7-9 Rebuild of Single Phase Motor Assembly .......................................................................................................................... 24

Paragraph 7-10 Rebuild of Three Phase Motor Assembly ........................................................................................................................... 24

Paragraph 7-11 Reassembly of Hoist From Subassemblies ....................................................................................................................... 25

Paragraph 7-12 Testing Hoist ......................................................................................................................................................................... 31

Paragraph 7-13 Test Procedure For Checking Operation of Overload Clutch ........................................................................................... 31

SECTION IX REPLACEMENT PARTS ....................................................................................................................................................................

Notice: Information contained in this book is subject to change without notice.

12773A

Figure 1-1. Cutaway View Of Typical Yale Electric Hoist

SECTION I - GENERAL DESCRIPTION

1-1. GENERAL. Yale Portable Electric Hoists are precision built chain type hoists ranging in six rated load sizes from 1/4 ton thru 3 tons with various lifting speeds and electrical power supplies. In addition to the capacities, there are model variations with roller or coil type load chains, hook or lug type suspension, and single or two speed. In addition to standard models, there are four rated load sizes of Yale Electric Hoists ranging from 1/

4 ton thru 2 tons suitable for plating hoist service with various lifting speeds and electrical power.

1-2. HOIST SERVICE CLASSIFICATION a. Yale electric hoists at the time of manufacture comply with our interpretation of applicable sections of ANSI B30.16

“Overhead Hoists”, National Electric Code ANSI/ NFPA 70 and

Occupational Safety and Health Act, 1992.

b. OSHA places the burden of compliance for hoist installations on the user. The user must install the equipment in accordance with the National Electric Code ANSI/NFPA 70 as well as other federal, state and local regulations which apply to the installation and application in your particular area.

WARNING

Equipment covered herein is not designed or suitable as a power source for lifting or lowering persons. Do not use as an elevator.

c. These hoists meet ANSI/ASME HST-1M “Performance

Standard for Electric Chain Hoists” hoist duty class ratings as outlined in the sales bulletin.

1-3. BASIC CONSTRUCTION. All sizes and models of these

Yale Electric Hoists are of the same basic designs, having many common and interchangeable parts. They consist primarily of an aluminum alloy frame and gear case cover which houses the gear train. An electric driving motor and external motor brake are mounted on the rear of the frame, Electrical control components are mounted on front of the gear case cover and encased by aluminum alloy end cover. An upper hook or lug bracket for suspending the hoist is attached to the top of the frame. Either a special nickel steel roller load chain or high strength low alloy coil load chain with lower block assembly is employed to raise and lower loads. Hoist operation is controlled by a pendant push button station.

Page 3

1-4. DIFFERENCES BETWEEN MODELS AND SIZES. The main differences between hoist models are in the service classification, type of load chain and the suspension employed.

These are described in paragraphs (a) thru (d), below. The differences between sizes of hoists are in the number of gear reductions used and the reeving of the load chain. Two-reduction gearing is used for 1/4 thru 1/2 ton rated load hoists; threereduction gearing for 1, 2 and 3 ton rated hoists. On 1/4 thru 1 ton rated load hoists, the load chain is single reeved (one part of chain); on 2 ton rated loads, the chain is double reeved (two parts of chain); on three ton rated loads, the chain is triple reeved (three parts of chain).

a. Two different types of load chains are used as the lifting medium, roller chain and coil chain. The roller type chain is a special precision manufactured nickel steel chain. Coil type chain is full-flexing electric welded link chain. Both are especially designed for use in Yale Electric Hoists and only factory approved chain of the correct size, pitch, hardness, and strength can be used with these hoists.

b. Suspension differences include a conventional hook type mounting and a lug type mounting. Hook suspension allows portability permitting hoist to be easily moved from job to job.

Lug suspension permits hoist to be rigidly mounted to overhead structure or attached to Yale Rigid Mount Trolleys, affording unusual headroom advantage.

c. Some hoists are adaptations of standard model hoists to permit use in some mildly corrosive atmospheres, high ambient temperatures and high duty cycle operation. They are available only in coil chain models in either hook or lug suspension.

Construction variations from standard models are as follows:

(1) Load chain is zinc plated for corrosion resistance.

(2) All exposed aluminum parts are prime painted with corrosion resistant paint.

(3) Aluminum castings are specially treated.

1-5. OVERLOAD CLUTCH. Yale Electric Hoists are equipped with an overload clutch that is designed to help guard against excessive overloads. It is a cone-friction clutch that connects the first reduction gear to the clutch pinion shaft. A belleville disc spring provides clutch pressure between the gear and its cone shaped gear center. An excessive overload causes the gear to rotate without turning the gear center and pinion shaft.

See paragraph 3-5 for operation.

WARNING

THE OVERLOAD CLUTCH IS A PROTECTIVE DEVICE

THAT WILL PERMIT OPERATION OF YOUR HOIST

WITHIN ITS RATED LOAD AND WILL PREVENT LIFTING

OF EXCESSIVE OVERLOADS WHICH CAN CAUSE

PERMANENT DEFORMATION OR WEAKENING OF A

PROPERLY MAINTAINED HOIST AND/OR ITS

SUSPENSION.

SECTION II - INSTALLATION

2-1. GENERAL. Yale Electric Hoists are completely lubricated and load tested under their own power before being shipped from the factory. To place hoist in service, attach to suitable overhead suspension (par. 2-2) in area to be used; make preinstallation check (par. 2-3); and connect to the proper power supply (par 2-4).

2-2. INSTALLATION.

CAUTION

Lubricate load chain before operating hoist. See paragraph

4.3

a. On hook suspended hoists, select a suitable overhead support in area hoist is to be used (one capable of holding weight of hoist and its rated load) and hang up hoist. Be certain upper hook is firmly seated in center of hook saddle. Upper hook is equipped with a spring type hook latch; it may be necessary to remove latch to attach hook to support. Replace latch after hoist is installed.

b. On lug suspended hoists, select a suitable overhead support in area hoist is to be used (one capable of holding weight of hoist and its rated load). Mount hoist using thru bolts, of appropriate size, to fit mounting holes in suspension lug at top of hoist frame. (See table below.) The structure used to suspend hoist must be of sufficient strength to withstand reasonable forces to which hoist and support may be subjected. Hoist must be aligned with load to avoid side pulls.

c. On lug suspended hoists, the suspension lug is installed for cross mounting, the recommended condition. To rotate hoist

90° for parallel mounting (a special condition), follow instructions below:

(1) On 1/4 thru 1 ton hoists loosen set screw, rotate hoists in

90° increments and tighten set screw.

(2) On 2 ton hoists, remove hex socket head screw in lower lock plate. Remove lower lock plate. Rotate suspension lug to selected position and replace lock plate and hex socket head screw.

(3) On 3 ton hoists, the hanger bracket must first be removed from the hoist to provide access to suspension nut per Section

VII, par. 7-2. a. (4) and figures 7-2 and 7-3. To remove lug bolt, follow instructions in Section VII, par. 7-3. b. (3). With bolt removed lift lug from hanger and reposition as desired. The lug is located and prevented from turning by integral lugs on adjacent surfaces of the lug and the hanger. Reinstall suspension bolt, spherical washers and nut. Align hole in nut and suspension bolt. Reassemble hanger bracket to hoist.

d. On rigid mount trolley suspended hoists, the trolley side plates must be properly spaced so trolley will fit I-beam on which hoist will operate. Adjustment for various I-beam sizes is accomplished by rearrangement of spacer washers on thru bolts which connect trolley side plates to suspension lug on hoist. Refer to instruction sheet furnished with Yale Rigid Mount

Trolleys for complete instructions.

Page 4

SUSPENSION LUG BOLT SIZES AND SPACING

Hoist

Rated Load

(tons)

1/4, 1/2 &1

2

3

Bolt Diameter

(in)

5/8

1

1-1/4

Distance

Between Holes

(in)

3-1/8

5

6

2-3. PRE-INSTALLATION CHECK.

Check Oil Level (Fig. 4-1). The gear case has been filled with oil, to the proper level at the factory. However, the oil level should be checked before hoist is operated. Remove pipe plug from oil filler on side of hoist frame. Replace with supplied oil hole cover. Check oil level by removing oil level plug (side of frame). Observe if oil level is even with bottom of tapped hole.

If it is not, add oil, as specified in paragraph 4-2c. Also check load chain. Be sure it is properly lubricated. See paragraph 4-

3.

Check limit stops. Make sure the stop on the tail chain side is securely fastened to the proper link (see chart on page 30).

On single part hoists, make sure steel and neoprene stops are in place at lower block, with the steel stop closest to lower block. These stops are free to float on the chain, so they may have slipped up the chain during transport.

2-4. CONNECTING HOIST TO ELECTRICAL SERVICE.

a. All hoists are equipped with a flexible power cable extending from the hoist. A grounding type male plug or permanent connection in an outlet box may be used for connecting hoist to power supply. See table (fig. 2-1) for branch circuit conductor sizes.

Figure 2-1.

H.P.

1/4

1/2

1

2½

Power Supply

115-1-60

230-1-60

200, 230-3-60

460, 575-3-60

115-1-60

230-1-60

200, 230-3-60

460, 575-3-60

115-1-60

230-1-60

200, 230-3-60

460, 575-3-60

200, 230-3-60

460, 575-3-60

*Do not use

AWG Wire Size

#16 #14 #12

#10

#8

80 130 210 330

230 330 835

465 740 1180

#6

1440 2390

45 75 120 190 310 490

195 305 490 775 1235

280 450 715 1135

860 1440

* 45 75 120 190 300

120 190 300 475 720

180 290 460 730

560 900

60 100 150 250

260 420

Figure 2-1. Branch Circuit Conductor Size. Maximum length in feet for maximum wire size based on horsepower and power supply. Wire size for entire length of branch circuit and permanent wiring to main feeder. Power supply measured at hoist, while running and with normal load, must not vary more than ±5% of voltage on motor nameplate.

b. Follow local & National Electrical Codes when providing electrical service to hoist. Connect power wires in accordance with appropriate wiring diagram. Power supply must be the same voltage, frequency and phase as specified on the hoist nameplate.

WARNING

The green wire provided in the power supply cable is a grounding wire and must be connected to a proper ground. (Follow local code requirements and/ or National Electrical Code Article 250).

c. Dual voltage hoists with reconnected 230/460 volts, 3 phase,

60 hertz are (unless otherwise specified on customer’s order) shipped from factory pre-connected for operation on 460 volts.

If hoist is to be operated on 230 volts convert wiring by changing connections on terminal board. With hoist disconnected from power source, remove electrical compartment cover and reconnect terminal board leads. Refer to Wiring Diagram.

d. Dual voltage hoists with reconnected 115/230 volts, 1 phase,

60 hertz are (unless otherwise specified on customer’s order) shipped from factory pre-connected for operation on 230 volts.

If hoists are to be operated on 115 volts convert wiring by changing connections on terminal board. With hoist disconnected from power source, remove electrical compartment cover and reconnect terminal board leads, Also refer to Wiring Diagram.

WARNING

Serious damage to the hoist can occur with resulting hazard to operator and load. Three phase hoists must be properly phased each time they are installed or moved to a new power source or when service is performed on mainline (power source).

e. To properly phase the hoist follow these steps:

(1) Temporarily connect hoist to power source.

(2) Operate “



” button briefly to determine direction of travel.

(3) If hook raises, phase is correct and temporary connections should be made permanent.

(4) IF HOOK LOWERS, HOIST IS “REVERSE PHASED”

AND MUST BE CORRECTED BY INTERCHANGING

ANY TWO LEADS AT POWER SOURCE

CONNECTION. DO NOT CHANGE INTERNAL

WIRING OF HOIST.

f. For connecting hoist to a motor driven trolley, refer to instructions furnished in trolley manual.

2-5. ELECTRONIC ADJUSTABLE LIMIT SWITCH.

The electronic adjustable limit switch is set at the factory to allow for testing and must be reset as part of the hoist start-up procedure.

The limit switch arrangement consists of two sensors which protrude into the gear case at the sprocket gear, and a control module. The control module has two buttons for programming set points, an UP and DOWN green LED, and a red ALERT

LED.

When power is first applied to the hoist, one or both of the green LED's should be on, and the red ALERT light should be off. The hoist will operate between the points set at the factory.

If red ALERT light is on and both green lights are off, the hoist will not operate, the limits need to be set.

Page 5

To set limits:

(1) Press both SET buttons simultaneously. Both green LED's should come on, and the red ALERT LED should flash. Hoist can now be operated through full range of lift.

(2) Raise or lower hook to desired set point. It does not matter whether upper or lower limit is set first. Press the set button that corresponds to UP if the upper limit is to be set first, or DOWN if the lower limit is to be set first. The corresponding green LED should go out.

(3) Move hook to desired upper limit if the lower limit was previously set, or to the lower limit if the upper limit was previously set. The LED corresponding to the limit just set will come back on, indicating the hoist is no longer at that limit.

Press the set button that corresponds to UP if the upper limit is being set, or DOWN if the lower limit is being set. The corresponding green LED should go out. The red ALERT light should also go out.

(4) The upper and lower limits are now set. Operate the hoist to confirm the settings are at the desired limits.

Tips for setting limits:

For the initial setting, both limits must be set. If one setting is more critical, that one should be set first. For example, if the position at the lower limit is more important that the position at the upper limit, the lower limit should be set first.

Once the upper and lower limits are set, they can be changed without having to do both if the new limit is within the previously set limits. For example, if the lower limit is set too low, stop the hook at the desired position and press the DOWN set button.

The hook will now stop at the new limit.

When positioning the hook to set a limit, stop the hook in the same manner as it is likely to be stopped during normal operation. If it is likely that the limit will be reached when the hoist is traveling at full speed, then position the hook by pressing the pushbutton and releasing when the hook is at the desired position, without jogs. If jogs are used to position the hook for setting the limit, the hook may drift past the limit if tripped at full speed.

Note: The limit switch has a setting increment of ¼ revolution of the sprocket gear. This applies when setting the limits. The hoist may stop up to a maximum of 1 1/2 inches before the desired position for 5/16 chain, or 1 1/4 inches for ¼" chain. Once set, the hoist will repeatedly stop at the same location.

SECTION III - OPERATION

3-1. GENERAL. Operation of Yale Electric Hoists are controlled by a push button station suspended from the hoist electrical compartment. The station has a built-in mechanical interlock to prevent depressing both buttons simultaneously.

3-2. OPERATING HOIST.

a. Depress push button marked “



” to raise load. b. Depress push button marked “



” to lower loads.

c. Jogging the push buttons will give “hairline” load movement.

The quickness of the depressing motion will determine the amount of movement. Excessive use of this “jogging” feature will cause premature burning of contact points, motor overheating, and rapid motor brake wear.

3-3. PULLING AND ROTATING HOIST AND LOAD.

a. The push button station conductor cable has a built-in strain cable suitable for pulling trolley suspended hoists when not loaded. Do not use for pulling bridge cranes. Push on load or load chain or use a hand geared or motor driven type trolley to traverse loaded hoists.

b. To rotate hoist and load, push on one corner of load. The lower hook will pivot thru 360 degrees to permit load to be swung to the desired position. The upper hook (hook suspension models) is also designed to rotate so that side pulls will swing hoist to face load, thus reducing side thrust.

Figure 3-1. Lower Block Contacting

Stops at Upper Limit of Travel

3-4. UPPER AND LOWER LIMIT STOPS. Upper and lower limit stops are provided to guard against overtravel of load in either raising or lowering direction, which can cause damage to hoist. When highest position is reached, the lower block or lower block limit stop will cause the overload clutch to slip.

When the lowest block position is reached, the tail chain stop will cause the overload clutch to slip. Limit stops are intended as safety devices and should not be used on a routine basis to stop block travel. Lowering full rated capacity load at full rated speed into the limit stop is an especially severe condition and must be avoided at all times.

Figure 2-2.

Page 6

Figure 3-2. Actuator Contacting Stop

Tail Chain End of Load Chain

3-5. OVERLOAD CLUTCH OPERATION. The overload clutch is factory preset at assembly so that the hoist will lift its full rated load but will refuse to lift overloads within a range of 150 percent rated load to 200 percent rated load. If the load to be lifted exceeds the clutch factory setting, the motor will continue to run and will rotate the clutch gear without lifting the load.

Whenever this occurs, immediately release the “



” push button to prevent overheating of the clutch friction surfaces and motor, and reduce the load to rated hoist capacity. Should it be impractical to reduce the load, replace the hoist with one of suitable rated capacity.

NOTE: Always know load to be lifted. Yale

Ÿ

Lift-Tech does not recommend lifting loads greater than the rated load of your hoist.

3-6. OPERATING PRECAUTIONS.

WARNING

Equipment covered herein is not designed or suitable as a power source for lifting or lowering persons. Do not use as an elevator.

Safe operation of an overhead hoist is the operator ’s responsibility. Listed below are some basic rules that can make an operator aware of dangerous practices to avoid and precautions to take for his own safety and the safety of others.

Observance of these rules in addition to frequent examinations and periodic inspection of the equipment may save injury to personnel and damage to equipment.

a. DO read ANSI B30.16 Safety Standard for Overhead

Hoists and the Operation, Service and Parts Manual b. DO be familiar with hoist operating controls, procedures and warnings.

c. DO make sure hook travel is in the same direction as shown on controls.

d. DO make sure hoist limit switches function properly.

e. DO maintain firm footing when operating hoist.

f. DO make sure that load slings or other approved single attachments are properly sized and seated in the hook saddle.

g. DO make sure that the hook latch, if used, is closed and not supporting any part of the load.

h. DO make sure that load is free to move and will clear all obstructions.

i. DO take up slack carefully, check load balance, lift a few inches and check load holding action before continuing.

j. DO avoid swinging of load or load hook.

k. DO make sure that all persons stay clear of the suspended load.

I. DO warn personnel of an approaching load.

m. DO protect load chain from weld splatter or other damaging contaminants.

n. DO promptly report any malfunction, unusual performance, or damage of the hoist.

o. DO inspect hoist regularly, replace damaged or worn parts, and keep appropriate records of maintenance.

p. DO use the hoist manufacturer’s recommended parts when repairing a hoist.

q. DO use hook latches wherever possible.

r. DO apply lubricant to load chain as recommended. DO

NOT lift more than rated load.

s. DO NOT use the hoist load limiting device to measure the load.

t. DO NOT use damaged hoist or hoist that is not working correctly.

u. DO NOT use the hoist with twisted, kinked, damaged or worn chain.

v. DO NOT lift a load unless chain is properly seated in chain wheel(s) or sprocket(s).

w. DO NOT use load chain as a sling or wrap chain around the load.

x. DO NOT lift a load if any binding prevents equal loading on all supporting chains.

y. DO NOT apply the load to the tip of the hook.

z. DO NOT operate unless load is centered under hoist.

aa. DO NOT allow your attention to be diverted from operating the hoist.

ab. DO NOT operate the hoist beyond limits of load chain travel.

ac. DO NOT use limit switches as routine operating stops unless recommended. They are emergency devices only.

ad. DO NOT use hoist to lift, support or transport people.

ae. DO NOT lift loads over people.

af. DO NOT leave a suspended load unattended unless specific precautions have been taken.

Page 7

ag. DO NOT allow sharp contact between two hoists or between hoist and obstructions.

ah. DO NOT allow the chain or hook to be used as a ground for welding.

ai. DO NOT allow the chain or hook to be touched by a live welding electrode.

aj. DO NOT remove or obscure the warnings on the hoist.

ak. DO NOT adjust or repair a hoist unless qualified to perform hoist maintenance.

al. DO NOT attempt to lengthen the load chain or repair damaged load chain.

am. DO NOT allow personnel not physically fit or properly qualified to operate the hoist.

an. DO NOT operate hoist unless upper and lower limit switch stops are operating properly.

ao. DO always be sure there is no twist in coil load chain.

On 2 & 3 ton coil chain hoists, check to see that lower block is not capsized between strands of chain.

ap. DO avoid operating hoist when hook is not centered under hoist. Be sure that hoist trolley or other support mechanism is correctly positioned for handling the load before lifting.

aq. DO operate hoist within recommended duty cycle and do not “jog” unnecessarily.

ar. DO conduct regular visual inspections for signs of damage or wear.

as. DO NOT operate hoist with hooks that have opened up.

See Figures 5-5 and 5-6.

at. DO provide supporting structure or anchoring means that has a load rating at least equal to that of the hoist.

au. DO NOT use hoists in locations that will not allow operator movement to be free of the load.

av. DO when starting to lift or pull, move the load a few inches at which time the hoist should be checked for proper load holding action. The operation shall be continued only after the operator is assured that the hoist is operating properly.

aw. DO NOT leave a loaded hoist unattended at the end of a work shift or for extended periods during the work shift.

Where operations are such that this condition cannot be avoided the operator must be assured that the condition does not create a hazard to personnel or property.

ax. DO use common sense and best judgement whenever operating a hoist. Observe American National Standard

Safety standard, ANSI B30.16, latest issue.

4-2. CHANGE GEAR CASE OIL (Fig. 4-1).

a. Remove drain plug from bottom of hoist frame and drain oil from gear case. Replace plug.

b. Remove oil level plug from side of hoist.

c. Refill gearcase thru oil filler to proper level (bottom of oil level plug hole) using Automatic Transmission Fluid - DEXRON

Type. This is an all-weather oil available from all major oil companies. 1-1/2 pints of oil are required.

d. Reinstall oil level plug.

4-3. LUBRICATE LOAD CHAIN. A small amount of lubricant will greatly increase load chain life, therefore, chain should not be allowed to run without lubricant. Chain should be cleaned and lubricated as directed in paragraphs a. and b. below, depending upon type of chain. User should set up a regular schedule for chain lubrication after observing operating conditions for a few days. Use Bar and Chain Oil (LUBRIPLATE or equal) on load chain.

10077L

Figure 4-1. Location of Oil Filler and Plugs a. Coil Chain. Under ordinary conditions only weekly attention will be necessary. Under hot and dirty conditions it may be necessary to clean chain at least once a day and lubricate it several times between cleanings. Thoroughly clean chain with an oil solvent and re-lubricate by coating it lightly with oil.

Make sure that lubricant coats wear surfaces between links.

Zinc plated load chain should be cleaned and lubricated daily.

b. Roller Chain. Under ordinary conditions only monthly attention will be necessary. Under hot and dirty conditions weekly attention may be required. Thoroughly clean chain with an oil solvent and apply oil. Wipe off excess oil. When subjected to excessive moisture or corrosive atmospheres, DO (dripless oil) lubricant from American Grease Stick Company is recommended for use on roller chain in place of regular oil.

Page 8

SECTION IV - LUBRICATION

4-1. GENERAL. The lubrication services outlined in paragraphs

4-2 thru 4-5 should be performed at regular intervals to maintain top hoist performance and insure long life. The frequency for lubrication services will depend on the type of hoisting service that hoist is subjected to and should coincide with periodic preventive maintenance inspection. See Section V-Maintenance.

4-4. LUBRICATE UPPER HOOK AND LOWER BLOCK

ASSEMBLY.

a. Apply a few drops of Bar and Chain Oil on shank of upper hook where it enters frame.

b. Apply a few drops of Bar and Chain Oil on shank of lower hook where it enters lower block. Hook rotation bearing may be removed for cleaning and re-lubricating if necessary. See paragraph 7-5.

c. On lower block assemblies of 2 and 3 ton capacity hoists, also apply heavy duty lithium soap grease with EP additives thru pressure fitting in end of sprocket pin to lubricate bearing in chain sprocket.

d. On 3 ton model lubricate sprocket in hanger bracket with a few drops of Bar and Chain Oil in hole provided in center of sprocket hub.

about. 015" deep. Chain must be replaced before the case is worn thru. Also check chain for elongation using a vernier caliper (fig. 5-2). Select an unworn, unstretched section of chain

(usually at slack or tail end) and measure and record the length over the number of chain links (pitches) indicated in figure 5-2. Measure and record the same length of a worn section in the load side of the chain. Obtain the amount of wear by subtracting the measurement of the unworn section from the measurement of the worn section. If the result (amount of wear) is greater than the amount specified in the

“ALLOWABLE CHAIN WEAR” table, the chain has elongated beyond the maximum allowable length and must be replaced.

Chain with excessively pitted, corroded, nicked, gouged, twisted or worn links should be replaced using only factory approved chain. Never weld or attempt to repair coil chain.

WARNING

Before performing any internal work on hoist, be certain power is shut off. Lock main service switch in the open position.

SECTION V - MAINTENANCE

5-1. GENERAL. Preventive maintenance services required on

Yale Electric Hoists are for the most part, simple periodic inspection procedures to determine condition of hoist components. Below are suggested inspection procedures, based on daily average hoist usage.

5-2. THIRTY-DAY INSPECTION. Hoist may be left suspended.

a. Inspect Load Chain.

(1) Operate hoist under load and observe operation of chain over sprocket in both directions of chain travel. Chain should feed smoothly into and away from the sprocket. If chain binds, jumps or is noisy, first see that it is clean and properly lubricated.

If trouble persists, inspect chain as outlined below, depending on type of chain.

Figure 5-2. Check Coil Chain Using Vernier Caliper

ALLOWABLE CHAIN WEAR - ELONGATION

Hoist

Rated Load

(tons)

1/4 & 1/2

1 thru 3

Chain Size

(wire dia.)

1/4"

5/16"

No. of

Pitches to Measure

13

11

Maximum

Wear Limit

.145"

.142"

WARNING

Do not assume that load chain is safe because it measures below replacement points given herein. Other factors, such as those mentioned in visual checks above, may render chain unsafe or ready for replacement long before elongation replacement is necessary.

Figure 5-1. Check Chain Wear at Bearing

Surfaces Between Links

(2) Coil Type Load Chain. Clean chain for inspection.

Examine visually for gouges, nicks, weld spatter, corrosion or distorted links. Slacken chain and check bearing surfaces between links for wear, fig. 5-1. Greatest wear will often occur at sprocket at high or low point of lift, particularly when hoist is subjected to repetitive lifting cycles. Case hardness of chain is

WARNING

To avoid serious personal injury from a dropped load caused by chain breakage, when replacing coil load chain, use only factory approved chain conforming to

Yale hoist specifications for material, hardness, strength and link dimensions. Chain not conforming to factory

Specifications may be dangerous as it will not fit in the load sprocket and chain guide correctly, causing serious internal damage to hoist and it will wear prematurely, deform and eventually break.

Page 9

(3) Removing and Replacing Coil Load Chain.

(a) Replacement Coil load chain is installed by attaching it to tail end of old chain, after disconnecting old chain from side of hoist frame and removing limit actuator. New chain is then run into hoist as old chain is run out. Use open “C” links, figures 5-3 and 5-4, for attaching chains. Links must be identical in size to hoist chain - 1/4" wire size with .745" pitch length for

1/4 thru 1/2 ton models, 5/16" wire size with .858" pitch for 1 thru 3 ton models. Be certain that all welds on links of replacement chain face away from center of load sprocket.

NOTE: See table on page 30 for location of tail chain limit stop.

On 2 ton double reeved models, also connect opposite end of chain (from lower block) to load chain anchor inside of frame.

On 3 ton triple reeved models, the opposite end of the chain is attached to the lower block connecting link.

NOTE: In the event the old chain is to be removed from hoist and reinstalled, a short length of chain (about 18" long) must be run into hoist when the old chain is removed.

This short length can then be used in the same manner as shown in paragraph 5-2. a.(3). Be sure to use the proper number of open “C” links in order to correctly position end link on tail end of chain to fit anchor at side of hoist frame.

Figure 5-3. Open "C" Link for Removing and

Installing Coil Load Chain

CAUTION

To avoid serious internal damage to hoist, when installing coil load chain do not attempt to hand feed chain into hoist, or use a piece of wire in place of the method described herein. To do so may result in serious internal damage to hoist, as coil chain links must be properly seated in chain sprocket before chain is run into hoist. Install chain only as described in this manual.

CAUTION

Keep fingers clear of chain sprocket when replacing load chain.

Figure 5-4. Installing Coil Load Chain Using Two

"C" Links (1/4, 1/2 & 1 ton hoists)

(4) Roller Type Load Chain. Visually check for possible twists, broken links, wear or elongation. Any links that do not flex easily, even when lubricated, may be damaged and should be replaced. Check roller chains for elongation from wear by pulling chain taut and measuring as follows: On RC-625, 625 or H-5 size chain (5/8" pitch), measure distance over a length of 20 pitches (center-to-center distance, between 21 rivets) - it must not exceed 12-3/4 inches. On RC-750, H-6 or HF size chain

(3/4" pitch) measure length of 16 pitches (center-to-center distance between 17 rivets) - it must not exceed 12-1 /4 inches.

If chain exceeds the limit, replace damaged section or install new load chain assembly. Check chain for twist. If twist in any

5 foot extension exceeds 15 degrees, replace chain. Check chain for camber. If any section has side bow exceeding 1/4 inch in five feet, replace chain.

(b) Remove lower block assembly and actuator from old chain and attach them to replacement chain at end which was just run thru hoist. Install limit actuator (as noted below) on other end of chain and anchor chain to side of hoist frame.

WARNING

Do not assume that load chain is safe because it measures below replacement points given herein. Other factors, such as those mentioned in visual checks, may render chain unsafe or ready for replacement long before elongation replacement is necessary. Do not attempt to splice the

chain to replace worn or damaged sections unless you have the required equipment to properly spin rivet heads. It is suggested that you have this done by an authorized Yale Repair Station that is equipped with the necessary special tools.

Page 10

CAUTION

Two "C" links must be used on 1/4, 1/2 and 1 ton capacity hoists (fig. 5-4) in order to correctly position end link on tail end of chain to fit tail end anchor at side of hoist frame; only one "C" link is required on 2 thru 3 ton capacity hoists.

WARNING

When replacing roller type load chain, use only factory approved chain conforming to factory specifications for material, hardness, tensile strength, size and construction. Yale Hoist Roller chain is specially designed for hoisting service and is the only type roller chain that can safely be used with Yale electric hoists.

Chain not conforming to Yale Roller Chain specifications may be dangerous as it will not withstand heavy impact loads and does not have adequate tensile strength.

(5) Check anchor end of chain at side of hoist frame for damage to last link, also connecting link on roller chain hoists.

Replace damaged parts.

(6) Check connection of chain to lower block on 1/4 thru 1 and 3 ton hoists. Replace parts showing evidence of damage, twisting or elongation.

(7) Check connection of chain to anchor inside hoist frame on double-reeved, 2-ton hoists. Replace parts showing evidence of damage, twisting or elongation. (Also see Sec. VII, par. 7-2.

a. (2)).

(8) Lubricate load chain before using hoist. See paragraph 4-

3, Section IV.

b. Inspect Lower Block.

(1) Check for bent or distorted hook. If hook is opened beyond the dimension given in figure 5-5, it must be replaced. Also check to see that hook swivels and is free to pivot. Lubricate these points if necessary.

(2) On 2 thru 3 ton hoists, check sprockets and bearings in lower block for freedom of movement and signs of damage.

Lubricate if necessary. Replace damaged parts.

(3) Check hook latches. Replace damaged or bent latches or broken springs.

WARNING

Hooks, upper or lower, damaged from chemicals, deformation or cracks or having more than 15 percent in excess of normal throat opening or more that 10 degrees twist from the plane of the unbent hook, or opened, allowing the hook latch to bypass hook tip must be replaced.

Any hook that is twisted or has excessive throat opening indicates abuse or overloading of the hoist. Other load bearing components of the hoist should be inspected for damage. (See Section V. Par. 5-2. d. (2) below).

Hoist

Rated Load

(tons)

1/4 & 1/2

1

2

3

Figure 5-5. Lower Hook Opening

(Shown with latch removed for clarity.)

Normal

Opening

1-1/8

Hook Throad Opening

Replace Hook if Opening is Greater Than

1-1/4

1-1/4

1-3/8

1-1/2

1-7/16

1-9/16

1-11/16

Hoist

Rated Load

(tons)

1/4 & 1/2

1

2

3

Normal

Opening

1-1/8

Hook Throad Opening

Replace Hook if Opening is Greater Than

1-1/4

1-1/4

1-3/8

1-1/2

1-7/16

1-9/16

1-11/16

Figure 5-6. Upper Hook Opening

(Shown with latch removed for clarity.) c. Inspect Upper Suspension.

(1) On hook suspended models, check for bent or distorted hook. If hook is opened beyond the dimension given in figure

5-6, it must be replaced. Also check to see that hook pivots.

Lubricate if necessary.

(2) On lug suspended models, check condition of suspension lug. Replace lug if damaged or cracked. Check to see that lock plate is in place on lug and screw holding it is tight.

(3) On 2-ton hoists, check to see that upper lock plate securing hook or lug bushing is in place and screws holding it are tight.

Lubricate hook shank.

(4) Check hook latch. Replace damaged or broken parts.

Page 11

(5) Inspect threaded upper suspension bushing. Verify keeper is in place and securing screw and lock washer are in place and tight.

d. Inspect Motor, Frame and Electrical Compartment Cover.

(1) Check to see that bolts securing motor to frame are tight.

Also check for any visible damage to motor, such as a cracked end bell or dented stator housing. Replace damaged parts.

(2) Check hoist frame for signs of visible damage. If frame shows evidence of fracture, the hoist should be disassembled and inspected for further signs of damage from possible overloading. Replace damaged parts.

(3) Check for possible damage to electrical compartment cover. Be sure screws holding cover are tight.

e. Check Oil Level. Remove oil level plug (fig. 4-1). If oil level is not even with bottom of tapped hole, add Automatic

Transmission Fluid, DEXRON Type, to bring to proper level.

5-3. SIX-MONTH INSPECTION OR 500-750 HOURS OF

OPERATION. Hoist may be left suspended. Same as thirty day inspection plus the following: a. Inspect Electrical Controls. Shut off power supply to hoist and remove electrical compartment cover from hoist. Use caution as some covers contain counterweights. Two speed hoists with a 2-1/4 horsepower motor have an externally mounted counterweight at the electrical compartment cover.

(1) Check all wiring and terminals. Insulation should be sound and terminals securely crimped to wires. Terminal screws should be tight and plug-type terminals completely mated. Replace terminals or wires as necessary.

(2) Check control circuit transformer for evidence of overheating. Replace if necessary.

(3) Check limit switch to see that wires are securely attached and mounting screws are tight.

(4) Check contactor solenoid coils and replace coils if they show evidence of overheating.

(5) Check control cable wire strain reliever to see that it is in good condition and securely attached to gear case cover.

Replace rubber strain reliever grommets if damaged.

a. Change Gear Case Oil. See Section IV, paragraph 4-2.

b. Relubricate Load Chain. See Section IV, paragraph 4-3.

c. Lubricate Upper Hook and Lower Block. See Section IV, paragraph 4-4.

5-4. INSPECTION: 5000 HOURS “ON” TIME OR 5 YEARS

ELAPSED TIME. Hoist must be removed from overhead suspension.

a. Disassemble Hoist into Subassemblies. Follow procedure outlined in Section VII, paragraph 7-2.

b. Motor shaft oil seal, sprocket shaft bearing, seal and all gaskets should be replaced.

c. Inspect Load Brake and Overload Clutch. Disassemble load brake (if equipped) and clutch assembly as outlined in paragraph 7-4. Friction discs should be discarded and replaced with new discs. Check load brake friction surfaces on flange, ratchet assembly and gear clutch cone. Replace parts if badly scored or worn. Check condition of pawl and ratchet assembly.

If pawl, ratchet teeth or pawl spring are broken, damaged or badly worn, replace complete assembly. Check contact faces of load brake cam and gear clutch cone. Brake gear and pinion teeth should be inspected for wear or broken teeth. Clean parts thoroughly with an oil solvent before reassembly.

NOTE: The overload clutch assembly should not be disassembled as it is preset at the factory to provide proper clutch pressure for a specific hoist capacity range.

If there is evidence of the clutch slipping or wear or damage to the clutch components, the complete clutch assembly should be replaced or sent to an authorized

Yale Hoist Repair Station to be rebuilt and properly adjusted to factory specifications.

d. Inspect Sprocket and Intermediate Gears.

(1) On 1 thru 3 ton hoists, check condition of gear teeth on intermediate gear and pinion shaft assembly. Replace worn or damaged parts.

(2) Check condition of teeth or pockets on chain sprocket (all capacities). Replace worn or damaged parts.

e. Inspect Motor Brake. Check braking surfaces for wear and scoring. Replace badly worn or scored parts. Check spring studs and guide pins to make sure they are not bent or loose.

Check coil shock mounts for deterioration and damage. Check air gap adjustment. (See 7-11c) f. Reassemble and Test Hoist. Reassemble hoist from subassemblies following procedure outlined in paragraph 7-11.

After assembly is complete, test hoist as outlined in paragraphs

7-12 and 7-13.

Page 12

Trouble

6-1. Hoist Will Not Operate.

6-2. Hook Moves in Wrong Direction.

6-3. Hook Will Raise But Not Lower.

6-4. Hook Will Lower But Not Raise

(continued on next page).

SECTION Vl - TROUBLE SHOOTING

Probable Cause

a. No power to hoist.

b. Wrong voltage.

c. No control voltage.

d. Loose or broken wire connections in hoist electrical system.

e. Contactor assembly not functioning.

Remedy

a. Check switches, circuit breakers and connections in power supply lines. Check power collectors.

b. Check voltage required on motor data plate against power supply.

c. Check transformer fuse. If blown, check for grounding and/or short in the pushbutton station. Check the transformer coil for signs of overheating. Replace transformer if burned out. Verify the transformer secondary is the same voltage as the coils to which it is connected.

d. Shut off power supply, remove electrical cover from hoist and check wiring connections

Also check connections in push button station and limit switches.

e. Check for burned out solenoid coil. See that the necessary jumper wires are properly installed.

f. Replace burned out parts.

f. Starting switch burned out

(single phase motor).

g. Motor burned out.

h. Electronic Limit Switch not set.

g. Replace motor. On single-phase motors the starting switch may be burned out.

h. Adjust electronic Limit Switch. See section

2-5.

a. Reverse phasing on threephase hoists.

b. Hoist wired wrong.

c. Starting switch not working correctly (single phase motor).

a. "DOWN" electrical circuit open.

b. Contactor assembly not functioning.

c. Push Button Inoperative.

d. Load Brake locked up and overload clutch slipping.

a. Excessive load, causing overload clutch to slip.

b. Overload clutch out of adjustment.

c. "UP" electrical circuit open.

a. Interchange any two of the three power supply line leads. Do not change green ground lead. Refer to Section II, par. 2-4.

b. Check wiring connections with appropriate wiring diagram.

c. Check for correct starting switch part number and function. Replace if necessary.

a. Check for loose connections. See that necessary jumper wires are properly installed on contactor. Check limit switch condition and electrical connections.

b. See that necessary jumper wires are properly installed. Verify that the contactor armatures are free to move. If binding occurs replace contactor. Check for burned out contactor coils.

c. Check push button contacts and wires.

d. Consult Authorized Yale Hoist Repair

Station.

a. Reduce loading to rated load of hoist, as shown on nameplate.

b. Test hoist and replace clutch if hoist will not lift rated load.

c. Check for loose connections. See that necessary jumper wires are properly installed on contactor. Check limit switch condition and electrical connections.

Page 13

SECTION Vl - TROUBLE SHOOTING (Continued)

Trouble

6-4. Hook Will Lower But Not Raise

(continued).

Probable Cause

d. Contactor assembly not functioning.

e. Push button inoperative.

Remedy

d. See that necessary jumper wires are properly installed. Verify that the contactor armatures are free to move. If binding occurs replace contactor. Check for burned out contactor coils.

e. Check push button contacts and wires.

6-5. Hoist Will Not Lift Rated Load.

a. Low voltage b. Overload clutch out of adjustment.

c. Motor brake not releasing.

a. See that power supply is same voltage listed on motor data plate. Check size of power supply lines. Refer to fig. 2-1.

b. Remove and replace clutch assembly. Refer to Section IV, par. 7-2 and 7-4.

c. Check brake components. Refer to Section

VII, par 7-2.d, 7-2.e and 7-2.f.

6-6. Excessive Drift When Stopping.

6-7. Hoist motor overheats.

a. Excessive load.

b. Motor brake not holding.

c. Motor brake not setting due to insufficient plunger air gap.

d. Load brake not holding.

a. Reduce loading to rated load, shown on nameplate.

b. Check brake components. Refer to Section

VII, par. 7-2.d.

c. Adjust air gap. Refer to Section VII, par.

7-11.c.

d. Remove load brake and inspect parts. Refer to Section V, par. 5-4.

a. Excessive load.

b. Excessive duty-cycle.

c. Excessive "jogging." a. Reduce loading to rated load of hoist, shown on nameplate b. Reduce frequency of lift.

c. Reduce frequency of jogs.

d. Wrong voltage.

e. Starting switch on singlephase motors not opening starting winding.

d. Check voltage rating on motor data plate against power supply.

e. Refer to Section VII, par. 7-9.b. (3) (b).

Inspect Switch.

f. Damaged motor or worn f. Disassemble hoist and inspect for worn or bearings in motor or hoist frame.

damaged parts.

g. Motor brake not releasing.

g. Check brake components. Refer to Section

VII, par. 7-2.d.

SECTION VII - DISASSEMBLY AND

REASSEMBLY

7-1. GENERAL.

a. The following disassembly and reassembly instructions apply to all standard models in the line of Yale Electric Hoists equipped with an overload clutch. Where needed, variations to instructions are provided to cover differences between models

(suspensions, load chains, rated load sizes and motor voltage ratings), with applicable models specifically noted.

b. A complete teardown procedure is given, however, if only certain parts require repair or replacement, a partial teardown may be performed using the applicable portions of the instructions.

c. For easier handling during disassembly, the following disassembly steps may, where conditions permit, be completed before hoist is removed from its overhead suspension or disconnected from its power supply: Remove chain container, if hoist is so equipped; remove lower block and load chain assembly, following procedure outlined in paragraph 7-2. a.

Drain and discard gear case oil, by removing plug at bottom of frame.

d. These hoists contain precision machined parts and should be handled with care at disassembly and at reassembly. When removing or installing parts with press fits, be careful to apply pressure evenly. On ball bearings, apply pressure to face of inner or outer race, whichever is adjacent to mating part. This will avoid damage to bearing races from brinelling by pressing thru bearing balls. Apply a thin film of sealant to parts having a press fit when they are installed.

Page 14

7-2. DISASSEMBLY OF HOIST INTO SUBASSEMBLIES.

a. Removal of Lower Block and Load Chain Subassembly.

(1) On models with single-reeved load chains (1/4 thru 1 ton rated loads) disconnect tail end of load chain from anchor at side of frame. Remove spring clip and connecting link attaching chain to anchor on roller chain models (fig. 7-1). Remove fillister head screw holding end link to frame on coil chain models.

Remove grooved pin from the limit actuator and pull it off end of chain. With hoist connected to power supply, run chain out of hoist by operating in “lowering” direction. (See note following paragraph (2) below and note in Sec. V, par. 5-2. a. (3) for inserting short length of chain.)

Figure 7-2. 3 Ton Hanger Bracket Connection Pin Removed

10308

Figure 7-1. Removing Spring Clip from Connecting Link at Tail End of Load Chain (Roller Chain Models)

(2) On models with double-reeved load chains (2 ton hoists) disconnect tail end of load chain from anchor at side of hoist frame and remove limit actuator as in (1) above, run chain out of hoist by operating it in “lowering” direction, and disconnect opposite end of load chain from anchor inside hoist frame. To disconnect this end of chain, remove cotter pin from end of anchor pin, press pin from anchor and withdraw chain. On roller chain models the anchor in hoist frame must be rotated about 90° to permit removal of anchor pin. The drive pin securing threaded end of anchor in upper block assembly (at top of frame) must be removed in order to rotate the anchor.

NOTE: If hoist is inoperative and not equipped with a load brake, chain can be pulled through by hand by first manually releasing motor brake. If hoist is equipped with a load brake it will be necessary to wait until after load brake is removed (paragraph. c., below), then the chain can be pulled thru the hoist by hand.

(3) On triple-reeved 3 ton coil chain hoists, remove retaining ring and connecting link pin as shown in figures 7-30 and 7-31.

Remove connecting link with chain from lower block.

Figure 7-3. Removing 3 Ton Hanger Bracket from Hoist Frame

To remove connecting link from chain, take out cotter key and push anchor pin from connecting link. Chain can now be pulled thru hanger bracket and lower block. Unfasten tail chain from hoist frame, remove limit actuator, and if power is available, operate hoist in lowering direction to remove chain. (See note in Sec. V, par. 5-2. a. (3) for inserting short length of chain). If hoist is inoperative see note below but be sure to install short length of chain into hoist before removing load chain.

NOTE: If hoist is inoperative and not equipped with a load brake, chain can be pulled through by hand by first manually releasing motor brake. If hoist is equipped with a load brake it will be necessary to remove load brake

(paragraph. c, below) so chain can be pulled thru the hoist by hand.

(4) To remove 3 ton hanger bracket from hoist, remove retaining ring and connecting rod pin (see fig. 7-2). Rotate hoist approximately 45° (see fig. 7-3) and hanger will slip free from hoist frame.

b. Removal of Electrical Compartment Cover, Electrical

Controls and Gear Case Subassembly.

(1) Disconnect hoist from power source. Remove three cover retaining screws and lift off cover (fig. 9-1). Cover screws have

Page 15

retaining rings which hold them in cover. Use caution as some covers contain counterweights. Two speed hoists with a 2-1/4 horsepower motor have an externally mounted counterweight at the electrical compartment cover.

(2) Disconnect push button conductor cable leads at plug-in type connectors that can be pulled apart. Remove screw and washer securing strain reliever (fig. 9-8) and pull the cable and grommet from its slot in gear case cover.

(3) Disconnect power supply flexible cable leads from terminals of contactor. Remove screw attaching ground leads to gear case cover and pull flexible cable and grommet from slot in cover.

(4) Disconnect motor leads from electrical control units.

Number of leads depends on type of motor. (See wiring diagrams in accompanying this manual).

(5) Remove eight hex socket head screws and lockwashers securing gear case cover to hoist frame. Pry gear case cover off hoist frame using screw driver at special notches provided at opposite corners of cover (fig. 7-4). Discard gear case cover gasket.

c. Removal of Load Brake and Clutch Assembly and

Intermediate Gear Subassembly.

(1) On 1/4 thru 1/2 ton hoists, pull load brake/clutch assembly if equipped or overload clutch assembly and the shaft washers from inside hoist frame (fig. 7-7). Caution: Grease-retained bearing has 36 rollers (all capacities) and may be reinstalled unless rollers are broken or missing or cup is damaged.

10314

Figure 7-7. Removing Load Brake and Clutch Assembly

(1/4 & 1/2 Ton Hoists)

10311

Figure 7-4. Prying Gear Case Cover from Hoist Frame

Figure 7-7a.

(2) On 1 thru 3 ton hoists, pull load brake or clutch assembly and intermediate gear assembly, including the thrust washers for each unit, from hoist frame (fig. 7-8).

Page 16

Figure 7-6. Gear Case Cover with Electrical

Controls Removed from Frame

10315A

Figure 7-8. Removing Load Brake and Clutch and

Intermediate Gear Subassemblies (1 thru 3 Ton Hoists)

Figure 7-9. Removing Motor Assembly

7-3. REBUILD OF HOIST FRAME, SPROCKET GEAR,

SPROCKET SHAFT AND CHAIN GUIDE.

a. Disassembly of Sprocket Gear, Shaft and Chain Guide.

(1) Remove retaining ring from end of sprocket shaft and pull off sprocket gear using a common puller (fig. 7-10). Remove

Woodruff key from shaft.

Figure 7-8a.

d. Removal of Motor Brake.

(1) Remove acorn nuts holding brake cover and remove brake cover (fig. 9-16).

(2) Disconnect wire nuts on brake coil leads.

(3) Remove brake mounting plate screws (fig. 9-16) and lift brake assembly off to gain access to the motor mounting bolts.

e. Removal of Motor Assembly.

(1) Place hoist frame on wood blocks to protect intergral gear on motor shaft. Loosen four motor mounting bolts and lift motor assembly from frame (fig. 7-9). Guide motor leads through wire passage to avoid damage.

10322

Figure 7-10. Pulling Sprocket Gear from Sprocket

Shaft using Common Puller

(2) Unscrew four fillister head machine screws securing sprocket bearing retaining plate and remove plate (fig. 7-11).

Remove and discard ring gasket from groove around bearing.

Page 17

10323

10326

Figure 7-11. View of Sprocket Bearing Retaining Plate

(3) Remove "C" clips holding chain guide pins in place. Pull guide pins out from motor side of frame. (Fig 7-13)

Figure 7-14. Removing Sprocket Shaft and Front Bearing

NOTE: Do not remove oil seal, ball bearings, and needle bearings from their bores in the frame unless they show evidence of wear or damage and require replacement.

When replacing rear sprocket ball bearing pack bearing

1/2 full with NLGI No. 2 grease.

10327

Figure 7-13. Removing Chain Guide Support Pins

(4) Remove sprocket shaft and front ball bearings assembly from frame by lifting up on end of shaft while prying up on sprocket as illustrated in figure 7-14. The chain guide will need to be repositioned in frame as sprocket shaft is raised to allow the sprocket to pass thru hole of guide (fig. 7-15). On roller chain model hoists, the chain stripper must be partly removed from guide by prying it out using screw driver or other suitable tool. See figures 7-16 and 7-17.

Page 18

Figure 7-15. Chain Guide Being Removed from Frame as Sprocket Shaft is Lifted Out (Coil Chain Models)

10328

Figure 7-16. Chain Stripper being partially removed from

Chain Guide (Roller Chain Model)

Figure 7-18. Removing Upper Hook and Hook Nut from Hoist Frame (1/4 thru 1 Ton Models)

(2) On 2 ton models, unscrew two hex socket head screws holding suspension bushing lock assembly to upper bloc (fig.

7-19) and remove lock. Unscrew suspension bushing from block to remove hook. To disassemble block from frame, remove screw securing suspension bushing keeper. Remove drive pin securing threaded end of chain anchor in block and unscrew anchor. Unscrew suspension bushing to remove block.

10329

Figure 7-17. Chain Guide and Stripper being removed from

Frame as Sprocket Shaft is lifted out (Roller Chain Model)

Figure 7-19. View of Upper Hook Assembled to Hoist Frame (2 Ton Models)

b. Disassembly of Upper Hook. (Hook Suspension Models)

(1) On 1/4 thru 1 ton models, remove screw securing suspension bushing keeper. Unscrew suspension bushing from frame to remove hook.

NOTE: Hook and bushing assembly is not to be further disassembled as nut securing bushing to hook shank is welded in place at the factory. Only the assembly is available for replacement.

(3) On 3 ton models, remove retaining ring from connecting rod pin and push connecting rod pin through bracket and connecting rod, releasing hanger (see fig. 7-2). Raise hanger above hoist frame to provide access to hook nut. Rotate hook until grooved pin in nut is visible from end of hanger frame.

Using a drift punch, drive grooved pin thru hook nut until it hits hanger pocket. Remove drift far enough to hold nut from turning and unscrew hook from nut. Thrust washer will fall free.

Page 19

(4) To remove connecting rod (fig 7-2) on 3 ton hoist, remove screw securing suspension bushing keeper. Unscrew suspension bushing to remove connecting rod from frame.

a. Disassembly.

(1) Place load brake and clutch assembly, flange up, in a vise equipped with brass or copper jaw plates to protect pinion gear teeth. Remove snap ring of load brake shaft (fig. 7-21).

10333

Figure 7-20. Removing Suspension Lug

(1/4 thru 1 Ton Models)

Figure 7-21. Removing Snap Ring from Load Brake Shaft

c. Disassembly of Suspension Lug (Lug Suspension Models).

(1) On 1/4 thru 1 ton models, remove screw securing suspension bushing keeper. Remove suspension lug using an extra thin 1-1/4" open end wrench to unscrew suspension bushing from frame. (See fig. 7-20).

(2) On 2 ton models, remove three hex socket head screws securing the two lock plates to block at top of frame and pull out locks. Remove suspension lug, using an extra thin 1-1 /4" open end wrench to unscrew suspension bushing from block.

Instructions for removing block from frame are given in paragraph b. (2).

NOTE: The suspension lug is not to be further disassembled, as nut securing suspension bolt and bushing to lug is permanently secured in place at the factory. Only the suspension lug assembly is available for replacement.

(3) On 3 ton models lug bolt is removed in same manner as hook. See paragraph 7-3. b. (3).

d. Reassembly.

(1) Before assembly, all parts should be thoroughly cleaned and inspected to determine their serviceability. Replace parts that are excessively worn or damaged.

(2) Reassemble suspension hook or lug, chain guide, sprocket shaft and sprocket gear to frame following a reverse procedure of the disassembly steps listed in paragraphs (a.) thru (c.), above. If ball bearing is to be reinstalled on sprocket be certain to position it so that the seal side of bearing faces out, away from sprocket. To help prevent oil seepage, apply sealant on

O.D. of sprocket bearing and in seat for the ring gasket.

7-4. REBUILD OF LOAD BRAKE AND OVERLOAD CLUTCH

ASSEMBLY. (If hoist is equipped with overload clutch less load brake, see 7-4a.)

10334

Figure 7-22. View Showing Load Brake Flange Removed

(2) Using a puller tool, remove brake flange from shaft. A groove is provided around outer diameter for this purpose. See figure 7-22. Remove key from shaft and lift off 2 friction discs, and the pawl and ratchet assembly (fig. 7-23).

Page 20

Figure 7-24a.

10335

Figure 7-23. Removing Pawl and Ratchet Assembly from Load Brake Shaft

(3) Remove load brake gear and overload clutch assembly from output pinion shaft. Pull the spring from its recess in clutch cone (fig. 7-24) but do not further disassemble gear and clutch assembly. See “NOTE” below.

NOTE: Disassembly of the load brake gear and overload clutch assembly (fig. 7-24) is not recommended. Clutch pressure is preset by the factory at assembly to provide the correct torque to allow the clutch to refuse loads within a specified range (150% of rated load to 200% rated load). It is suggested whenever there is a need to repair or readjust the gear and clutch assembly that it be sent to an authorized Yale Hoist Repair Station where adequate tools, fixtures and appropriate test equipment is available.

11927

(4) The load brake pawl and ratchet is a riveted assembly and is not to be disassembled.

b. Reassembly.

(1) Before assembly, all parts should be cleaned and inspected to determine their serviceability. Replace parts that are worn or damaged.

(2) Reassemble load brake parts following a reverse procedure of the disassembly steps listed above, observing the assembly steps (3) thru (6) below.

(3) Before installing spring in its recess in center of clutch cone (fig. 7-24) apply a good grade of ball bearing grease to inside of recess. Spring must be positioned exactly as illustrated, abutted against pin.

(4) When installing pawl and ratchet assembly on load brake shaft, be certain that teeth on ratchet face are in the same direction as shown in fig. 7-23. The ratchet assembly should rotate freely when turned counterclockwise and the pawl should engage ratchet teeth when unit is turned clockwise.

(5) When installing brake flange position it with chamfer facing friction disc, figure 7-22.

(6) The brake spring must be pre-loaded at assembly to a torque of from 6 to 10 lb. ft. when used with yellow (color code) spring and a torque of 10 to 14 lb. ft. when used with plain (no color code) spring. (See Section IX for proper spring). This is accomplished using a plumber’s strap wrench to wind (rotate) load brake gear to set up spring (fig. 7-25) while pressing brake flange into place using an arbor press. Clamp pinion end of shaft into a portable vice to keep brake from rotating in press. Use brass or copper jaw plates on vise to protect pinion gear teeth. Wind gear counterclockwise (viewing brake from flange end) with strap wrench and press down on flange until snap ring groove in shaft is exposed allowing snap ring to be installed. Use extreme care not to over wind spring as yield will result and final spring torque will be reduced. Do not wind gear beyond point necessary to install snap ring in groove.

Figure 7-24. Load Brake Gear and Overload Clutch

Assembly Removed from Load Brake Shaft

Showing Brake Spring Installed in Clutch Cone

Page 21

10610

11868

Figure 7-25. Winding Load Brake Gear

Using a Strap Wrench to Set Up Load Brake Spring

Figure 7-26. Removing Roll Pin Securing Hook Nut to Hook Shank

7-4A. OVERLOAD CLUTCH WITHOUT LOAD BRAKE.

Disassembly of the clutch gear and overload clutch assembly

(fig 7-24a) is not recommended. Clutch pressure is preset at the factory at assembly to provide the correct torque to allow the clutch to refuse loads within a specified range (150% of rated load to 200% rated load). It is suggested whenever there is a need to repair or readjust the overload clutch assembly that it be sent to an authorized Yale Hoist Repair Station where adequate tools, fixtures, and appropriate test equipment is available.

7-5. REBUILD OF LOWER BLOCK AND LOAD CHAIN

ASSEMBLY.

a. Disassembly (1/4 through 1-ton, single reeved models).

(1) Separate load chain (link or roller type) from lower block assembly. Drive out small roll pin securing lower block pin in lower block yoke and push lower block pin from yoke to release chain. On roller chain models, an adapter is used to attach chain to lower block. This adapter is removed from end of chain by first driving out small roll pin and then pushing out adapter pin.

(2) Drive grooved pin from limit actuator and pull actuator from end of chain.

(3) Lower blocks are of a pinned construction, permitting replacement of body, thrust bearing, or hook and nut assembly.

To disassemble, drive spring pin from hook nut (fig. 7-26). With pin removed, hold hook nut from turning with drift punch and rotate hook to unscrew it from nut.

Separate hook, bearing shield, needle bearings and two thrust washers from body. Hook and nut are drilled at assembly and are replaced only as an assembly.

b. Disassembly (2-ton, double reeved models).

(1) On 2-ton roller chain models, remove retaining ring from one end of sprocket pin and press pin from lower block body.

Grasp chain and pull out sprocket and two spring washers from body. Do not remove needle bearing from sprocket or pressure lube fitting from sprocket pin unless replacement is necessary.

(2) On 2-ton link chain models, remove fillister head screw securing center guide in top of lower block body and lift out guide (fig. 7-27) and sprocket pin lock (fig. 7-28). Press sprocket pin from body and pull out chain, sprocket and washer (fig. 7-

29). Do not remove bushing type bearing from sprocket or pressure lube fitting from sprocket pin unless replacement is necessary.

10336A

Figure 7-27. Removing Chain Center Guide from

2 thru 5 Ton Lower Block Assembly (Link Chain Model)

Page 22

10337A

Figure 7-28. Removing Sprocket Pin Lock on

2 thru 5 Ton Lower Block Assembly (Link Chain Model)

11752A

Figure 7-30. Removing Retaining Ring from Bore of

Connecting Link Pin - 3 Ton Lower Block Assembly

10338A

Figure 7-29. Removing Coil Chain and Sprocket on

2 thru 5 Ton Lower Block Assembly (Link Chain Model)

(3) To disassemble hook and nut, drive groove pin from hook nut with drift punch. With pin removed, hole hook nut from turning with drift punch and rotate hook to unscrew it from nut.

Separate hook, nut, bearing shield, needle bearing and two thrust washers from body. Hook and nut are drilled at assembly and are replaced only as an assembly.

c. Disassembly (3-ton, triple reeved models).

(1) Remove chain sprocket from lower block following procedure for 2-ton link chain models described in paragraph

7-5. b. (2) above.

(2) To disconnect end of chain anchored to lower block, remove retaining ring from pin bore (fig. 7-30). Push connecting link pin from bore by pressing through hole provided in opposite side of block (fig. 7-31). Chain connecting link is now free and can be further disassembled for inspection.

11752B

Figure 7-31. Removing Connecting Link Pin from 3 Ton

Lower Block Assembly

(3) To remove hook from lower block body, first drive grooved pin from hook nut. Then hold nut from turning using drift punch and rotate hook to unscrew it from nut. Separate hook, shroud and thrust washer from body. Note that bearing surface of washer faces nut.

(4) To remove chain sprocket from upper suspension hanger, first remove hanger as outlined in paragraph 7-2. a. (4). With hanger removed, push sprocket pin from hanger and sprocket.

NOTE: Sprocket pin must be removed toward side having small anti-rotation pin slot in hanger.

d. Reassembly of Lower Blocks.

(1) Clean, inspect and replace worn or damaged parts.

(2) Lubricate and reassemble following a reverse procedure of the disassembly steps above.

Page 23

7-6. REBUILD OF ELECTRICAL CONTROLS AND GEAR

CASE COVER SUBASSEMBLY.

a. Disassembly.

(1) Disconnect two limit switch leads from contactor. Also, if hoist has a transformer, disconnect transformer leads at the contactor or terminal board.

(2) Remove reconnectable terminal board if so equipped.

(3) Remove two screws and lift transformer from gear case cover if hoist is so equipped.

(4) Remove two screws attaching contactor assembly to cover and lift off contactor. Refer to paragraph 7-8 for instructions for rebuild of contactor assembly.

(5) Remove two hex socket head screws and lockwashers securing limit switch assembly to gear case cover and pull limit switch assembly and control shaft from cover.

(6) Loosen two nuts and screws holding limit switches to retainer bracket and remove.

(7) Remove self-locking nut from end of control shaft and pull off washer, switch activator, centering lever, spring, spacer tube, retainer bracket and washer.

NOTE: Do not remove needle bearings from gear case cover unless they show evidence of wear or damage and require replacement.

b. Reassembly.

(1) Before assembly, all parts should be thoroughly cleaned and inspected to determine their serviceability. Replace parts that are worn or damaged.

(2) Reassemble parts to gear case cover in reverse of the disassembly steps above. Ends of centering spring must straddle centering levers. Lubricate contact segments of limit switch with small amount of graphite grease.

7-7. REBUILD OF PUSH BUTTON STATION AND

CONDUCTOR CABLE ASSEMBLY.

a. Disassembly.

(1) Remove seven pan head machine screws and lockwashers from back of push button station and lift off rear cover.

(2) Loosen three terminal screws and remove strain cable screw, lockwasher and plain washer.

(3) Remove two pan head machine screws and lockwashers from housing cap and remove cap, grommet and cable assembly.

(4) Remove two pan head screws, contact assembly and button assembly.

b. Reassembly.

(1) Before assembly, all parts should be thoroughly cleaned and inspected to determine their serviceability. Replace all parts that are worn or damaged.

(2) Reassemble push button station and conductor cable following a reverse procedure of the disassembly steps listed above.

NOTE: Do not attempt to shorten or lengthen push button conductor cable. Odd length conductor cable assemblies for other than standard 10 ft. lift hoists can be procured from the factory.

7-8. REBUILD OF CONTACTOR ASSEMBLY.

a. General. Wear or damage to contactor parts requires replacement of complete contactor assembly.

7-9. REBUILD OF SINGLE PHASE MOTOR ASSEMBLY.

a. Disassembly.

(1) To inspect capacitor, remove two cover mounting screws and lift off capacitor cover. Do not disconnect wires at capacitor unless capacitor must be replaced.

(2) Remove external retaining ring from end of shaft and press shaft out of bearing in end bell.

(3) Remove motor end bell from stator assembly. If necessary loosen it by tapping with soft mallet.

(4) Remove internal retaining ring from bearing bore in end bell and press out bearing assembly.

b. Reassembly.

(1) Before assembly, all parts should be cleaned and inspected to determine their serviceability. Replace all parts that are worn or damaged.

(2) Reassemble motor following a reverse procedure of the disassembly steps listed above.

(3) After reinstalling hoist motor, connect hoist to power supply and carefully complete both checks (a) and (b) below:

(a) To check direction of rotation, briefly operate “



“ button. If hook lowers, interchange motor lead ‘T1" with “T4” at the contactor or controller. Hook must raise when the “



“ push button is operated.

(b) To check the starting winding switch, connect ammeter

(minimum 10 ampere) to motor lead “T5”. Amperes must drop to zero in approximately one second when operating hoist in both “



“ and “



“ directions. If ampere reading does not drop to zero, interchange motor leads “T7” and “T8”. If, after above checks were made with motor having been run in both directions, the ammeter reading still does not return to zero, the motor switch is not functioning properly and should be replaced.

WARNING

Do not change circuit wiring. Severe damage and malfunction of hoist may result.

7-10. REBUILD OF THREE PHASE MOTOR ASSEMBLY.

a. Disassembly.

(1) Pull four motor mounting bolts from motor and separate stator assembly from the end bell and rotor shaft assembly.

(2) Remove external retaining ring from end of motor shaft and press shaft from bearing in end bell.

(3) Remove internal retaining ring from bearing bore in end bell and press out bearing assembly.

Page 24

b. Reassembly.

(1) Before assembly, all parts should be cleaned and inspected to determine their serviceability. Replace all parts that are worn or damaged.

(2) Reassemble motor following a reverse procedure of the disassembly steps listed above.

7-11. REASSEMBLY OF HOIST FROM SUBASSEMBLIES.

a. General. The procedure to be followed to reassemble the hoist from subassemblies is in reverse order of the disassembly steps outlined in paragraph 7-2. Listed below are special assembly precautions which should be observed to assure proper assembly.

NOTE: Grease retained bearings (see Section VII, par. 7-

2. c. (1) and fig. 7-7) have loose rollers. When reassembling hoist, make certain the correct number of rollers are held in roller cup with grease before assembling load brake shaft to hoist.

b. Assembly of Load Brake Thrust Washers. When reinstalling load brake assembly be certain thrust washers are properly installed at both ends of load brake shaft, as noted below.

(1) A bronze thrust washer with a lug on one side belongs on pinion end of shaft and must be installed so that its lug engages the special slot located on spotface surrounding bearing bore inside hoist frame or gearcase cover. Use heavy grease to hold washer in proper position in frame or cover (depending upon hoist capacity) during assembly.

(2) A 5/8" I.D. steel thrust washer is to be installed on the brake flange end (end opposite pinion) of load brake assembly.

c. Motor Brake. Instructions for adjusting the brake are inside the brake cover and are repeated below. Check brake adjustment after first 30 days of service and regularly thereafter during the six-month inspection procedure.

Installation and Service Instructions for 54,000 Series

(rev. A) Manual Adjust Brakes.

Caution

1. Installation and servicing must be made in compliance with all local safety codes including Occupational Safety and Health

Act (OSHA). All wiring and electrical connections must comply with the National Electric Code (NEC) and local electric codes in effect.

2. To prevent an electrical hazard, disconnect power source before working on the brake. Lock disconnect in the off position and tag to prevent accidental application of power.

3. Be certain power source conforms to the requirements specified on the brake nameplate.

4. Be careful when touching the exterior of an operating brake.

Allow sufficient time for brake to cool before disassembly.

Surfaces may be hot enough to be painful or cause injury.

5. Do not operate brake with housing removed. All moving parts should be guarded.

6. After usage, the brake interior will contain burnt and degraded friction material dust. This dust must be removed before servicing or adjusting the brake.

DO NOT BLOW OFF DUST using an air hose. It is important to avoid dispersing dust into the air or inhaling it, as this may be dangerous to your health.

a) Wear a filtered mask or a respirator while removing dust from the inside of a brake.

b) Use a vacuum cleaner or a soft brush to remove dust from the brake. When brushing, avoid causing the dust to become airborne. Collect the dust in a container, such as a bag, which can be sealed off.

General Description - This series brake is spring set, electrically released. These brakes will contain one or two friction discs driven by a hub mounted on the motor.

Operating Principle - When the brake coil is energized the lever arm retracts the spring force from the disc pack, allowing the friction disc to rotate with the hub and motor shaft. When power is removed the lever arm pushes down on the stationary disc and friction discs. The hub is held from rotating, and the load is held in place.

Important - Please read these instructions carefully before installing, operating, or servicing. Failure to comply with these instructions could cause injury to personnel and/or damage to property if the brake is installed or operated incorrectly.

WARNING

Do not release brake if there is a suspended load on the hoist hook.

Manually releasing the brake will allow a suspended load to fall, possibly causing damage, injury or death.

Weight of load chain may be sufficient to cause entire chain to run through hoist if brake is released. Be sure chain is secured.

Always be certain any suspended load (which includes below the hook devices or attachments) are removed before servicing, adjusting or removing brake.

If chain is moved causing rotation of the sprocket without the electronic limit switch powered, check upper and lower limit settings before resuming normal operation.

Page 25

Œ

Place hub on motor shaft.



Apply Loctite 680 to set screws.

Tighten set screws on motor shaft.

78 lb-in

Ž

Remove brake housing and gasket.



Align friction disc with splined hub and slide brake against motor face.



Insert mounting screws and tighten.

15-20 lb-in

‘

Connect coil leadwires to power supply. Refer to nameplate for voltage rating.*

Caution: Keep wiring away from pinch points

and moving components.

’

Replace brake housing and tighten to 8 lb-in.

Clockwise

Page 26

Air Gap Adjustment

Brake air gaps are factory adjusted to .100”. As friction discs wear the air gap will increase. When the gap reaches .200” it will need to be readjusted to .100”.

1. Loosen jam nut (10N).

2. Turn adjusting screw (10) CW until .100” gap is reached

(see Fig. 1).

3. Retighten jamb nut.

4. Check air gap again...

Air Gap

Friction Disc Replacement

Friction disc(s) should be replaced when the wear area is

3/32" thick or less.

1. Remove the two brake mounting screws and lift the brake assembly from the hub / motor.

2. Remove the two support bracket screws (3s), and lift the brake and solenoid assembly (3) off the brake.

3. Lift the lever arm (17) forward and slide the friction disc(s) out of the brake assembly.

4. Insert new friction disc(s) under the stationary disc (5). If brake has two friction discs align the center spline holes with each other.

5. Align the brake and friction disc assembly on the hub (16) and slide onto the motor. Insert and tighten the two brake mounting screws (15-20 lb-ft).

6. Reposition the support bracket assembly (3) on the brake, and retighten the two support bracket screws (3s), (52 lbin).

Note: Air gap readjustment will be required after disc replacment.

Adjust

Screw

Jam Nut (10N)

Fig. 1

Torque Adjustment

The brake is factory set for nominal rated torque. No further adjustment to increase torque may be made. The approximate compressed torque spring height is shown below. Torque reduction may not exceed 1 full turn in the CCW direction (1.5

lb-ft brake cannot be reduced). Note that the spring measurement for the 6 and 9 lb-ft spring is from inside the shoulder washer.

3

17

35

4

Brake Torque

(lb-ft)

1.5

3

6

9

Length "L"

(in.)

1.102

.954

1.286

1.188

Max Torque Reduction

(ccw turn of torque nut)

0

1

1

1

%

Reduction

0

15

25

15

1-1/2 and 3 lb-ft

6 and 9 lb-ft

5

Coil Replacement

1. Remove the two support bracket screws (3s), and lift the bracket and solenoid assembly (3) off the brake.

2. Remove the plunger guide (140) from the inside of the coil.

3. Remove the thru-bolt (160) from the leadwire side of the coil by backing off the lock-nut (210). Slide the bolt, shock mount pads and flat washer out of the way.

4. Remove the coil (12) from the solenoid frame (79) by pushing down on the coil locking tab on the side opposite the leadwires. Push the coil out of the frame.

5. Insert the new coil into the solenoid frame in reverse of the steps of removal. Insert the new plunger guide (140) into the coil, locking tabs first.

6. Position a shock mount pad (150) on both sides of the solenoid mounting bracket, and reinsert the thru-bolt (160) through the shock pads and bracket.

7. Slide a flat washer (170) over the bolt, and tighten the locknut down until the shock pads begin to flatten.

Page 27

8. Position the solenoid and bracket assembly (3) over the plunger (29) and slide into place. Tighten the bracket mounting screws (3s) to 52 in-lb.

9. Reassemble brake motor by following steps 5-8 of the brake mounting procedure.

9. Position the solenoid and bracket assembly (3) over the plunger (29) and slide into place. Tighten the bracket mounting screws (3s) to 50 in-lb.

10. Reassemble brake to motor by following steps 5-8 of the brake mounting procedure.

140

12

79



17

29

29N

29N

29S

29

210

35

3

170

150

160

Solenoid Replacement

1. Remove the two support bracket screws (3s), and lift the bracket assembly (3) off the brake.

2. Remove the plunger guide (140) from the inside of the coil.

3. Remove both thru-bolts (160) from the solenoid assembly

(79).

4. Remove the coil (12) from the solenoid frame (79) by pushing down on the coil locking tab on the side opposite the leadwires. Push the coil out of the frame.

5. Insert the coil into the new solenoid frame in reverse of the steps of removal. Insert the new plunger guide (140) into the coil, locking tab first.

6. Position the new shock mount pad (150) on both sides of the solenoid mounting bracket, and reinsert the tap-bolts

(160) through the shock pads and bracket.

7. Slide the flat washers (170) over the bolt, and tighten the locknut down until the shock pads begin to flatten.

8. Remove the plunger nut (29N) and screw (29S), and lift plunger (29) from lever arm (17). Install the new plunger to the lever arm using the new screw and nut provided. Tighten to 40 in-lb.

Page 28

Supply Voltage Cause

Line voltage >110% of coil rating

Excessive voltage drop during inrush time proper rated coil

TROUBLESHOOTING

Coil Failure

Supply Voltage Correction

Reduce voltage or replace with

Increase current rating of power supply

Excessive Wear/Overheating

Air Gap Cause Air Gap Correction

Low solenoid air gap

Reset air gap (refer to Air Gap

Adjustment)

Cycle Rate Cause Cycle Rate Correction

pull-in

Wiring Cause

Leadwires interfering with plunger

Wiring Correction

Reroute wiring away from plunger and other moving components

Brake "jogging" exceeding coil cycle rate

Thermal capacity is being exceeded

Reduce cycle rate or consider alternate control method

Reduce cycle rate, use alternate control method or increase brake size

Coil leadwire shorted to ground

Replace coil or leadwire and protect with wire sleeving

Alignment Cause Alignment Correction

Solenoid Assembly Cause Solenoid Assembly Correction

Broke endplate not concentric to motor C-Face

Motor resister must be within

.004" on concentricity

Plunger not seating flush against solenoid frame

Loosen solenoid mounting nuts and reposition frame to allow full face contact

Motor shaft runout is excessive

Must be within .002"; runout; consult motor manufacturer

Excessive solenoid/plunger wear at mating surface

Replace solenoid assembly

Worn Parts Cause Worn Parts Correction

Broken shading coils

Worn Parts Cause

Replace solenoid assembly

Worn Parts Correction

Friction disc excessively worn

(disc can wear to 1/2 original thickness or .093")

Endplate, stationary disc or pressure plate warped

Replace friction discs

Replaced warped or worn component

Excessive wear of solenoid link bolt

Plunger guide worn down and interfering with plunger movement

Application Cause

Machinery cycle rate is exceeding brake rating

High ambient temperature

(>110%) and thermal load exceeding coil insulation rating

Brake coil wired with windings of an inverter motor or other voltage/current limiting device

Replace link bolt; also inspect plunger thru-hole for elongation

Replace guide

Application Correction

Reduce brake cycle rate or use alternate control method

Use Class H rated coil and/or find alternate method of cooling brake

Wire coil to dedicated power source with instantaneous coil rated voltage

Linkages worn

Motor shaft endfloat excessive

Hub Cause

Burr on hub interfering with disc

"float"

Set screw backed out and interfering with disc

Miscellaneous

Replace all worn components

Endfloat must not exceed .020"; consult motor manufacturer

Hub Correction

File off burr

Retighten set screw; use Loctite®

680 to help secure

Miscellaneous

Miscellaneous Cause Miscellaneous Correction

Wiring is restricting disc pack movement

Reroute wiring

Wrong or over tightened torque springs

Replace with proper spring or refer to installation section for proper spring height

Excessive stop time

(2 seconds or greater)

Increase brake size/torque or use alternate control method

Excessive air gap Reset, refer to Airgap Adjustment

High Ambient termperature

(in excess of 110°F)

Reduce cycle rate or use alternate method of cooling d. Assembly of Load Chain.

NOTE: Coil chain must be installed so welds on vertical links face away from the load sprocket.

(1) On coil chain and roller chain models install load chain over sprocket before load brake assembly is installed. Insert anchor end of chain (end opposite lower block on single reeved models) into chain guide opening on far side of hoist (viewing frame from anchor screw side). Rotate sprocket gear by hand counterclockwise as chain is fed into opening. When sufficient chain has been run into hoist to reach anchor position, plus a slack loop, install limit stop on anchor end of load chain (see

(3) below) and attach end of chain to frame with special fillister head screw. Be certain chain is not twisted.

(2) On roller chain models, the chain may be installed after step (e) below is accomplished, allowing chain to be run into hoist under power. Caution must be exercised so that fingers or hands are not caught in chain while it is being fed into hoist.

NOTE: The spring clip connecting link must be attached to anchor end of roller load chain before chain is run into hoist. Failure to do so may result in damage to chain or hoist.

(3) When installing limit stop on anchor end of load chain attach it at link shown below. See Figure 3-2.

Page 29

Type Chain

Link

Link

Roller

Roller

Size Chain

1/4" Wire Dia.

5/16" Wire Dia.

5/8" Pitch

3/4" Pitch

Number of

Chain Links

From End Link

12 Links (9½")

10 Links (9")

7½ Links (9¼")

6½ Links (9¾") e. Wiring Hook-Up. Before installing hoist, connect wiring to electrical controls in accordance with applicable wiring diagram.

Wires are coded and/or numbered to agree with wiring diagrams.

f. Proximity Switch Replacement/Adjustment. The proximity switches are adjusted at the factory to have a gap of 1-2mm between the end of the sensor and the face of the sprocket gear. If the sprocket and/or sprocket gear are not being replaced, there should be no need to adjust the proximity switches. If the sprocket gear or sprocket have been replaced, or a proximity switch needs replacing, use the following procedure:

(1) The proximity switch needs to be set with an air gap of 1-

2mm between the sensor end and the face of the sprocket gear. With the proximity switch removed, use a flashlight to look through the mounting hole to verify that a gear surface is directly below the mounting hole.

CAUTION

Failure to line the proximity switch up with a gear surface could result in the proximity switch being inserted too far. This will result in damage to the proximity switch and possibly gear case cover if the hoist is operated.

(2) Thread the proximity switch in until it bottoms out on the gear face. Do not over tighten. Back out one full turn. This will leave a gap of approximately 1mm.

(3) Tighten lock nut to secure proximity switch.

Proximity switches are equipped with a red LED that lights when it is sensing the presence of metal. An optional method for setting the proximity switch air gap would be to use a proximity sensor tester suitable for use with a 15v proximity switch. This is connected directly to the proximity switch, and lights the LED when a surface is sensed.

Under certain conditions, if the hoist loses power during operation, the electronic limit switch may not detect a fault condition, but the upper and lower limits may have shifted. This would occur if the sprocket gear rotated in an even ¼ rotation increment (1/4, ½, ¾…). The distance between limits will remain the same, but the entire range will have shifted up or down accordingly. Operation of the electronic limit switch is to be checked daily per ASTM/ANSI.B30.16.

g. Lubricate Hoist. Lubricate hoist as outlined in Section

IV.

Figure 7-32.

WARNING

If chain is moved causing rotation of the sprocket without the electronic limit switch powered the limits may have shifted. Check upper and lower limit settings before resuming normal operation.

The hoist electronic limit switch requires power while the chain is in motion to maintain the limits at the desired position. If the gearing rotates while power is removed from the unit, the limits may have to be reset. A common example of a situation causing such gear movement would be during replacement of the motor or brake.

The electronic limit switch may fault if significant movement occurs when power is removed from the hoist. Such a fault will disable operation of the hoist. If the red SET light is on, with both green limit lights off, a fault has occurred and the limits must be reset after determining the cause of the fault.

Page 30

Figure 7-33.

7-12. TESTING HOIST.

a. General. After completion of reassembly and before placing hoist in service, hoist should be tested to insure safe operation.

To test: suspend hoist from an overhead supporting member of sufficient strength to carry rated load; connect to a power supply of the specified voltage (see data plate attached to motor); and perform the following checks and adjustments.

b. Check For Correct Control Operation. Refer to Section II, par. 2-4. d, under “Warning.” c. Check Upper and Lower Limit Operation. To determine if upper and lower limit stop functions properly, make the following checks while operating hoist with push button control:

(1) Press up push button and verify operation of electronic limit switch upper limit. Reset as necessary.

(2) Press down push button and verify operation of electronic limit switch lower limit. Reset as necessary.

(3) If hoist does not stop at one or both of the set limits, check for improper wiring. Refer to par. 6-2 and appropriate wiring diagram. If wiring is correct, check to see that proximity switches are correctly installed and sensing properly, par. 7-

11.f.

d. Check Hoist With Rated Load. Attach rated load to lower hook and check hoist operation. If hoist does not lift rated load, refer to par. 7-13.

(1) Operate hoist to raise load. When control is released, hoist should instantaneously stop and hold load at that level.

(2) Operate hoist to lower load a short distance, then release control. Hoist should stop instantaneously and hold load at that level.

(3) If hoist does not stop or hold load refer to Section VI.

7-13. TEST PROCEDURE FOR CHECKING OPERATION OF

OVERLOAD CLUTCH.

a. General. The overload clutch must be tested using known weights. The following prerequisites (par. (1) thru (4)) must be strictly observed in performing this test.

(1) A qualified person shall determine before testing, that all structures supporting the hoist are adequately strong to with stand the test load of 200 percent of rated hoist load, whether hoist is tested in installed position or moved to a designated test facility.

(2) Loads used for testing must be accurately known.

(3) Test shall be made only by a qualified operator thoroughly familiar with the hoist and the purpose of the test.

(4) Provide adequate and proper rigging to insure test loads are securely attached, properly balanced, and will lift level.

b. Test Procedure. With the above prerequisites satisfied and hoist properly connected to electrical power, proceed with the test as follows:

(1) Using a known load equal to rated load of hoist, operate hoist to lift load. Raise load high enough to be certain the entire load is freely suspended. Clutch should not slip at

rated load. If hoist does not lift rated load, clutch requires adjustment. Refer to Section V, par. 5-4. c.

(2) Increase load to 200 percent rated load and operate hoist to lift the load. Clutch must slip, causing the hoist to refuse to lift the load. If hoist lifts this overload, the overload clutch is out-of-adjustment and must be readjusted. Refer to Section V, par. 5-4. c.

(3) If clutch slips as required in step (2) above, continue to run hoist (clutch slipping-hoist refusing to lift load) for five (5) cycles of one (1) second each.

(4) Remove excess weight to return the load to rated hoist load. Lift rated load one final time to be certain that the clutch does not slip and that the hoist lifts the rated load.

WARNING

DO NOT LIFT MORE THAN RATED LOAD EXCEPT FOR TEST PURPOSES

NOTICE

THIS EQUIPMENT MUST BE EFFECTIVELY GROUNDED ACCORDING TO THE NATIONAL ELECTRIC

CODE, ARTICLE 250, 610-61 AND OTHER APPLICABLE CODES.

Page 31

SECTION IX - REPLACEMENT PARTS

This section contains complete replacement parts information for your new Yale Electric Hoist. The parts are grouped and illustrated in exploded view photos to permit easy identification.

Each part in an illustration is keyed by reference number to a corresponding parts table. In the table will be found the BH part number, description and quantity required.

When ordering replacement parts it will be necessary that you include, with your order, the BH part number of parts required, plus, hoist catalog number and model number, which will be found on the hoist nameplate attached to motor. For motors complete motor nameplate data is required. Complete inspection, maintenance and overhaul service is available for

Yale Electric Hoists at any of the Authorized Repair Stations.

All are staffed by qualified factory-trained servicemen; have authorized testing equipment; and stock a complete inventory of genuine replacement parts.

NOTICE: Information herein is subject to change without notice. Parts must be ordered from an Authorized Yale

Repair Station or from a Yale Hoist Distributor.

The numbers assigned to the parts of our various assemblies in our parts lists are not the part numbers used in manufacturing the part. They are identification numbers, that when given with the hoist serial number, permit us to identify, select or manufacture, and ship the correct part needed for any hoist.

Figure No.

9-10

9-12

9-13

9-14

9-15

9-16

9-5

9-6

9-7

9-8

9-9

9-1

9-2

9-3

9-4

INDEX OF EXPLODED VIEW PARTS ILLUSTRATIONS

Title Page

Frame and External Parts ......................................................................................................................... 34-37

Upper Suspension, Load Chain and Lower Block Parts (2 ton Hoists) .................................................. 38-39

Upper Suspension, Load Chain and Lower Block Parts (3 ton Hoists) .................................................. 40-41

2 and 3 Ton Lower Block Assembly (Link Chain Hoists) .............................................................................. 42

2 Ton Lower Block Assembly (Roller Chain Hoists) ...................................................................................... 43

Gearing and Load Brake Parts (1/4 and 1/2 Ton Hoists) ......................................................................... 44-45

Gearing and Load Brake Parts (1 thru 3 Ton Hoists) ............................................................................... 46-47

Electrical Control Units (Three Phase Single Speed Hoists) .................................................................. 48-49

Electrical Control Units (Two Speed Hoists Only) .................................................................................... 50-51

Electrical Control Units (Single Phase Hoists) ......................................................................................... 52-53

Push Button Station and Conductor Cable Assembly (Single Speed Hoists) ............................................. 54

Push Button Station and Conductor Cable Assembly (Two Speed Hoists Only) ......................................... 55

Single Phase Motor Assembly ....................................................................................................................... 56

Three Phase Motor Assembly ................................................................................................................... 57-58

Hoist Motor Brake ........................................................................................................................................... 59

Page 32

NOTES

Page 33

To enable us to expedite your parts order, always give Model and Catalog Number and Electric

Current of Hoist. (See nameplate.)

Figure 9-1. FRAME AND EXTERNAL PARTS

Standard and Plating Service Hoists

(Except 2 thru 3 Ton Model Upper Suspension, Load Chain and Lower Block)

6

7

4

5

Ref.

No.

1

3

Part

Number

BH-4007

BH4007A

BH-4003

BH-4004

BH-4005

BH-4006

BH-5009

BH-4008

BH-1007

BH-1008

Description

Hook Assembly-Upper with Latch (Includes Item 51) (for 1/4 & 1/2 ton)

Hook Assembly-Upper with Latch (Includes Item 51) (for 1 ton)

Frame Assembly (For Hoists with Cat. No. prefix letters A, C, G, H & J. Includes 2 bushings, 1 needle bearing, 1 cup, 1 oil seal, 1 oil filter, 2 pipe plugs, and 2 dowel pins.)

Frame Assembly (For Hoists with Cat. No. prefix letters D, K, L, P, M, S, T, W, & V.

Includes 2 bushings, 2 needle bearings, 1 oil seal, 1 oil filler, 2 pipe plugs and 2 dowel pins.)

Frame Assembly (For 1/4 & 1/2 ton special sealed frame hoists with suffix -4, -5).

Includes sealed frame, 2 bushings, 1 needle bearing, 2 oil seals, 1 oil filler, 2 pipe plugs, and 2 dowel pins.

Frame Assembly (For 1 & 2 ton special sealed frame hoists with suffix -4, -5).

Includes sealed frame, 2 bushings, 2 needle bearings, 2 oil seals, 1 oil filler, 2 pipe plugs, and 2 dowel pins.

Pin-Support, chain guide

Retaining Clip

Gasket-Gearcase

Cover Assembly-Gearcase (For Hoists with Cat. No. prefix letters

A, C, G, H & J. Includes 1 needle bearing, 1 cup and 2 grooved pins).

(Continued on following page)

Page 34

Qty.

Req’d

1*

1

1

1

1

2

4

1

1

9

10

11

Ref.

No.

8

19

20

21

22

23

24

12

13

14

15

16

17

18

25

26

27

28

29

30

Figure 9-1. FRAME AND EXTERNAL PARTS - Continued

Part

Number

BH-1009

BH-1082

BH-1095

BH-1157

BH-1010

BH-1096

BH-1014

BH-1168

BH-1169

YH-1190

YH-1191

YH-1192

YH-1193

YH-1194

BH-1020

BH-1021

BH-1022

BH-1023

BH-1024

BH-1025

BH-1026

BH-1027

BH-1028

BH-4015

BH-4016

BH-4017

BH-1031

BH-1032

***

BH-1033

BH-1034

BH-1080

BH-1086

***

BH-1039

BH-1040

BH-1075

BH-1076

BH-1171

BH-1172

BH-1173

BH-1043

BH-1044

BH-1035

BH-1035A

BH-1036

Description

Cover Assembly -Gearcase (For Hoists with Cat. No. prefix letters D, K, L, P, M, S, T,

W, & V. Includes 2 needle bearings and 2 grooved pins).

Cover Assembly-Gearcase (For 1/4 & 1/2 ton special sealed frame Hoists with suffix -4, -5). Sealed and includes 1 needle bearing, 1 cup and 2 grooved pins.)

Cover Assembly-Gearcase (For 1 & 2 ton special sealed frame Hoists with suffix

-4, -5). Sealed and includes 2 needle bearings and 2 grooved pins.)

Cover Assembly-Gearcase (For Two Speed Hoists with 2-1/4 Horsepower Motor Only.)

Cable Assembly-Flexible, 5' (Incl. Items 9 & 10)

115 volt, 1 phase, 60 hertz hoists

230 volt, 1 phase, 60 hertz hoists

200/230/460/575 volt, 3 phase, 60 hertz hoists

Grommet-Flexible Cable-3 phase

Grommet-Flexible Cable-1 phase

Clamp-Flexible Cable

Cover-Electrical Compartment

Without internal counterweight

With internal counterweight

Capacity Label (Not Shown)

1/4 Ton

1/2 Ton

1 Ton

2 Ton

3 Ton

Screw-Fillister Head Machine

Hi-Collar Helical Spring Lock Washer (1/4)

Ring-Retaining

Regular Helical Spring Lock Washer (#10 Pltd.)

Hex Socket Head Cap Screw (#10-24 x 3/4)

Grooved Pin (Type D 1/8 x 1/2 Pltd.)

Grommet-(Motor Driven Trolley Models)-Not Shown

Dowel Pin (3/8 x 3/4)

Hex Socket Pipe Plug (1/8)

Suspension Bushing Keeper

Lock Washer

Hex Socket Cap Screw

Guide Assembly-Coil Load Chain

1/4 & 1/2 ton Hoists

1 thru 3 ton Hoists

Chain Assembly-Coil, load

1/4" Dia.-1/4 & 1/2 ton Hoists

5/16" Dia.-1 ton Hoists

1/4" Dia.-1/4 & 1/2 ton Hoists - Zinc Plated

5/16" Dia.-1 ton Hoists - Zinc Plated

Chain Assembly-Roller, load

5/8" Pitch-For 1/4, and 1/2 ton Hoists

3/4" Pitch-For 1 ton Hoists

Repair Link-5/8" Pitch Roller Chain (not shown)

Repair Link-3/4" Pitch Roller Chain (not shown)

Slotted Spring Pin (3/32 x 5/8 Pltd.)

Adapter Kit-Roller Load Chain (Incl. Items 27, 28, 29, 40 and 41)

5/8" Pitch-For 1/4, and 1/2 ton hoists

3/4" Pitch-For 1 ton hoists

Pin-Adapter, roller load chain (5/8" Pitch)

Pin-Adapter, roller load chain (3/4" Pitch)

Block Assembly-Lower, coil and roller chain (Incl. items 32 thru 39)

For 1/4 ton Hoists

For 1/2 ton Hoists

For 1 ton Hoists

Note: Lower block assemblies do not include attaching pins or roller chain adaptor.

Order separately.

(Continued on following page)

Qty.

Req’d

1

1

1

1

1

1

1

1

1

1

1

1

1

1

2

1

8

8

2

3

3

1

1

2

1

1

1*

1*

1

1

1

1

1

1*

1*

Page 35

35

36

37

38

39

40

48

50

51

52

54

58

59

Ref.

No.

32

33

34

41

42

43

44

45

46

47

Figure 9-1. FRAME AND EXTERNAL PARTS - Continued

BH-1050

BH-1051

BH-1052

BH-1053

BH-1054

BH-5017

BH-5018

BH-1184

BH-1185

BH-4010

BH-1183

BH-1089*

BH-4011

BH-1158

BH-1159

BH-1160

Part

Number

BH-1174

BH-1174A

BH-1175

BH-1176

BH-1177

BH-1182

BH-1183

BH-1178

BH-1179

BH-1180

BH-1181

**

BH-1037

BH-1038

BH-1045

BH-1046

BH-1047

BH-1048

BH-1049

Description

Body-Lower Block, coil and roller chain

1/4 ton Hoists

1/2 ton Hoists

1 ton Hoists

Hook, Nut and Latch Assembly-Lower Block

1/4 and 1/2 ton Hoists

1 ton Hoists

Latch Kit-Hook, lower

1/4, and 1/2 ton Hoists

1 ton Hoists

Washer-Thrust, needle bearing

Bearing Assembly-Needle, thrust

Shield-Bearing

Grooved Pin (Type F 5/32 x 1-1/8 Pltd.)

Nut-Hook

Pin-Connecting, lower block

1/4 and 1/2 ton Hoists

1 ton Hoists

Slotted Spring Pin (3/32 x 3/4 Pltd.)

Stripper-Roller Chain

1/4 and 1/2 ton Hoists

1 & 2 ton Hoists

Guide Assembly-Roller Chain

1/4 and 1/2 ton Hoists

1 & 2 ton Hoists

Link Assembly-Roller Chain (For connecting tail end of chain only - Must not be used to join chain.)

1/4 & 1/2 ton Hoists

1 & 2 ton Hoists

Fillister Head, Self Locking Machine Screw (5/16-18 x 3/4 Pltd.)

Anchor-Link, roller load chain

1/4 & 1/2 ton Hoists

1 & 2 ton Hoists

Limit Stop

5/8" Pitch Roller Chain

3/4" Pitch Roller Chain

Grooved Pin (Limit Stop BH-1098) (Type F 7/32 x 2 Pltd.)

Grooved Pin (Limit Stop BH-1099) (Type F 1/4 x 2 Pltd.)

Filler Assembly-Oil

Latch Kit-Hook (upper) 1/4 thru 1 ton

Slotted Spring Pin (1/4 x 11/16 Pltd.)

Lug Suspension Assembly

The following items are for two speed hoists with 2-1/4 horsepower motor only:

Insert-Coil

Support Stud

Top

Bottom

(Continued on following page)

Qty.

Req’d

1*

1

1

1

2

1

1

2

2

2

1*

3

2

1

1

1

2

1

1

1

1

1

1

1

1

Page 36

Figure 9-1. FRAME AND EXTERNAL PARTS - Continued

64

65

66

67

68

60

61

62

63

BH-1161

BH-1162

BH-1163

YH-1164

YH-1165

YH-1166

BH-1063

BH-5010

BH-5011

BH-5012

BH-5013

BH-1410

Counterweight

Plain Washer (Type W 1/4 Pltd.)

Heavy Hex Self-Locking Nut (1/4 - 20)

Capacity Label

1 Ton

2 Ton

3 Ton

Urethan Bumper

Chain Stop Assembly

For 5/16" Coil Chain

For 1/4" Coil Chain

Stop Plate

Button Head Cap Screw

Lock Washer

* Refer to Figure 9-2 for 2 Ton Model Upper Suspension, Load Chain and Lower Block Parts.

Refer to Figure 9-3 for 3 Ton Model Upper Suspension, Load Chain and Lower Block Parts.

** Hook and suspension bolt nuts are not serviced separately. They are available only with hook or bolt as assemblies.

1

1

4

4

1

1

3

1

1

3

** Load Chain Assemblies listed are for hoists with standard

10 ft. lifts. Bulk chain is available in 1 ft. increments and 50 ft.

lengths as follows:

Â

Type Chain

Roller (5/8" Pitch)

Roller (3/4" Pitch)

Coil (1/4" Dia.)

Coil (5/16" Dia.)

Coil (1/4" Dia. Zinc Plate)

Coil (5/16" Dia. Zinc Plate)

50' Lengths

BH-1064

BH-1067

Not Available

Not Available

Not Available

Not Available

Bulk

BH-1065

BH-1068

BH-1066

BH-1069

BH-1083

BH-1093

Page 37

1

®-------

I

®-

~

®--

-

®

R .

23

-r--

REF .

To enable us to expedite your parts order, always give Model and Catalog Number and Electric

Current of Hoist. (See nameplate.)

6

8

15

Page 38

Figure 9-2. UPPER SUSPENSION, LOAD CHAIN AND LOWER BLOCK PARTS

(2 Ton Hoists)

10251B

Figure 9-2. UPPER SUSPENSION, LOAD CHAIN AND LOWER BLOCK PARTS - Continued

Ref.

No.

1

2

3

4

8

9

11

12

13

5

6

7

14

15**

16

17

18**

19

20

21

22

24

25

26

27

28

29

30

31

32

Part

Number Description

905422

BH-1102

BH-1030

BH-4013

BH-4014

BH-1106

BH-1107

BH-1108

BH-1109

BH-1061

*

*

BH-1110

Bracket Assembly Kit- Lug Suspension

(Coil Chain Model Only. Includes Items 6, 8 and 9).

Hook Assembly-Upper (Includes Items 5, 6, 7 and 20).

Grooved Pin (Type F 3/16 x 1-1/4 Pltd.)

Block Assembly-Upper

Coil Chain Models, Includes Items 3, 10, 11, 14, 16, 19 and 21

Roller Chain Models, Includes Items 3, 10, 12, 13, 14, 19 and 21

Lock Assembly-Suspension Bushing

Regular Helical Spring Lock Washer (#10 Pltd.)

Hex, Socket Head Cap Screw (#10-24 x 1/2)

Hex, Socket Head Cap Screw (#10-24 x 3/8)

Plate - Lock (Coil Chain Lug Suspension Models Only)

Anchor - Coil Load Chain

Anchor - Roller Load Chain

Pin - Roller Chain Anchor

BH-1111

BH-1112

BH-1076

BH-1113

Cotter Pin (3/32 x 3/4)

Chain Assembly-Roller Load (3/4" Pitch)

Repair Link-3/4" Pitch Roller Chain (Not Shown)

Pin-Coil Chain Anchor

(See Fig. 9-4) Block Assembly-Lower (Coil Chain Models)

(See Fig. 9-5) Block Assembly-Lower (Roller Chain Models)

BH-1114 Chain Assembly-Coil Load

BH-1115

*

BH-2213

Chain Assembly-Coil Load (Zinc Plated)

Suspension Bushing

Latch Kit-Hook

BH-4012

BH-5018

BH-5010

BH-4015

BH-4016

Spacer Washer

Chain Stop - Roller Chain

Coil Chain

Suspension Bushing Keeper

Lock Washer

BH-4017

BH-5012

BH-5014

BH-5013

BH-5015

BH-1410

BH-5016

Hex Socket Head Cap Screw

Stop Plate

Stop Block

Button Head Cap Screw

Socket Head Cap Screw

Lock Washer

Hi-Collar Lock Washer

Qty.

Req’d

2

1

1

1

1

1

As Req’d

1

1

1

1

1

1

1

1

1

1

1

1

1

3

2

1

2

1

1

2

2

2

1

1

1

1

1

* Not available as individual parts. Order upper block assembly, Item 4.

** Load Chain Assemblies listed are for hoists with standard 10 ft. lists. Bulk chain is available in 1 ft. increments and 50 ft.

lengths as follows:

Type Chain

Roller (3/4" Pitch)

Link (5/16" Dia.)

Link (5/16" Dia. Zinc Plate)

50' Lengths

BH-1067

Not Available

Not Available

Bulk

BH-1068

BH-1069

BH-1093

Page 39

To enable us to expedite your parts order, always give Model and Catalog Number and Electric

Current of Hoist. (See nameplate.)

® -

@ '.

/ -_

®

~ ~

Page 40

Figure 9-3. UPPER SUSPENSION, LOAD CHAIN AND LOWER BLOCK PARTS

(3 Ton Hoists)

11757B

Ref.

No.

1

2

3

25

26

27

29

30

20

21

22

23

24

31

32

33

34

35

15

16

17

18

19

10

11

12

13

14

4

7

8

5

6

9

Figure 9-3. UPPER SUSPENSION, LOAD CHAIN AND LOWER BLOCK PARTS - Continued

Part

Number

BH-1131

BH-1132

905424

BH-1134

BH-1135

BH-2214

BH-2217

BH-1138

BH-4018

BH-4015

BH-4016

BH-1142

BH-1143

BH-1144

BH-1145

BH-5019

BH-1147

BH-1148

BH-1149

BH-1150

BH-1151

BH-1152

BH-1153

See Fig. 9-4

BH-2210

BH-1154

BH-5010

BH-4017

BH-5012

BH-5014

BH-5013

BH-5015

BH-1410

BH-5016

Description

Suspension Pin and Nut Assembly

Spherical Washer

Suspension Lug Kit

(Includes Items 1, 2, 4 and 26)

Pin - Grooved (Type A 3/16 x 2 Pltd.)

Hook/Latch and Nut (Includes Item 6)

Latch Kit, Hook

Washer, Thrust

Hanger

Connecting Rod Assembly

Suspension Bushing Keeper

Lock Washer

Pin, Connection

Ring, Retaining

Sprocket & Bushing Assembly (Includes Item 15)

Bushing

Pin, Sprocket

Grooved Pin (Type A 3/16 x 3/8 Pltd.)

Chain Assembly, Coil Load

Link, Connecting

Pin, Anchor

Cotter Pin (3/32 x 3/4)

Dowel Pin (1/2 x 2-1/4)

Ring, Retaining

Block Assembly, Lower, Coil Chain

Washer, Thrust

Washer

Chain Stop Assembly

Hex Socket Head Cap Screw

Stop Plate

Stop Block

Button Head Cap Screw

Socket Head Cap Screw

Lock Washer

Hi-Collar Lock Washer

Qty.

Req’d

1

1 Pr.

1

1

2

1

1

1

2

1

1

1

1

1

1

1

1

1

1

1

1

1

1

2

2

1

2

2

1

2

2

1

1

NOTICE

Always insist on factory approved Yale Hoist replacement parts when servicing this equipment. Parts are available from your local Authorized Repair Station.

NOTES

Page 41

To enable us to expedite your parts order, always give Model and Catalog Number and Electric

Current of Hoist. (See nameplate.)

12444A

Ref.

No.

17

18

19

20

21

13

14

15

16

Page 42

5

6

3

4

7

1

2

9

10

11

12

Part

Number

BH-2219

BH-2218

BH-2202

BH-2203

BH-2204

BH-2205

BH-2206

BH-2207

BH-2208

BH-2210

BH-2211

BH-2212

BH-2213

BH-2214

BH-2215

BH-2216

BH-2217

BH-2220

BH-2221

BH-2222

BH-2223

BH-2224

BH-2225

Figure 9-4. 2 and 3 TON LOWER BLOCK ASSEMBLIES (Link Chain Hoists)

Description

Block Assembly-Lower Complete

Block Assembly-Lower Complete

Guide-Center

Lock-Sprocket Pin

Sprocket-Coil Chain

Bushing-Sprocket

Screw-Fillister Head, Self locking

Pin-Sprocket

Fitting-Hydraulic Drive

Washer, Thrust

Body Assembly-Lower Block

Hook/Latch and Nut (Includes Items 12, 13 and 15)

Latch Kit, Hook

Latch Kit, Hook

Pin, Grooved

Shroud

Washer, Thrust

Hook/Latch and Nut (Includes Items 12 and 17)

Pin, Grooved

Shield, Bearing

Bearing Assembly-Needle, Thrust

Washer, Thrust

Body-Lower Block

1

2

1

1

1

1

1

1

1

1

1

—

—

—

—

1

1

—

—

1

—

1

1

Quantity Required

2 Ton 3 Ton

1

1

1

1

1

—

1

1

1

1

1

1

—

1

1

1

1

—

—

—

—

—

—

To enable us to expedite your parts order, always give Model and Catalog Number and Electric

Current of Hoist. (See nameplate.)

10263B

Figure 9-5. 2 TON LOWER BLOCK ASSEMBLY (Roller Chain Hoists)

6

7

4

5

8

1

2

3

9

10

11

12

13

Ref.

No.

Part

Number

BH-2301

BH-2302

BH-2303

BH-2304

BH-2305

BH-2208

BH-2307

BH-2308

BH-2311

BH-2312

BH-2313

BH-2315

BH-2308

BH-2213

Description

Block Assembly-Lower, Complete

Washer-Spring Thrust

Sprocket-Chain

Bearing Assembly-Needle

Ring-Retaining, External

Fitting-Hydraulic Drive

Pin-Sprocket

Hook and Nut Assembly-Lower Block (Includes Item 12 below)

Pin-Grooved

Shroud

Washer-Thrust

Body Assembly

Hook and Nut Assembly

Latch Kit-Hook

NOTICE

Always insist on factory approved Yale Hoist replacement parts when servicing this equipment. Parts are available from your local Authorized Repair Station.

Qty.

Req’d

1

1

2

1

1

1

1

1

2

1

1

1

1

1

Page 43

To enable us to expedite your parts order, always give Model and Catalog Number and Electric

Current of Hoist. (See nameplate.)

Figure 9-6. GEARING AND LOAD BRAKE PARTS (1/4 and 1/2 Ton Hoists)

14

15

16

17

18

19

20

21

22

8

9

10

11

12

13

Ref.

No.

3

4

1

2

5

6

7

Part

Number

BH-1201

BH-1202

BH-1203

BH-1237

BH-1205

BH-1206

BH-1207

BH-1208

BH-1209

BH-1210

BH-1239

BH-1212

BH-1213

BH-1214

BH-1216

BH-1240

BH-1241

BH-1242

BH-1218

BH-1238

BH-1219

BH-1220

BH-1221

BH-1222

BH-1223

BH-1224

BH-1225

BH-1226

BH-1227

Description

Seal-Oil, motor shaft

Bearing Assembly-Ball, motor shaft

Ring-Retaining, Internal

Bearing Assembly-Needle, 11/16" I.D. (36 rollers, grease retained)

Bearing-Thrust, bronze

Washer-Thrust, 11/16" I. D. (Used with 14 tooth Pinion Load Brake

Shaft-13H-1207 below)

Shaft & Integral Pinion-load brake,

14 teeth

23 teeth

36 teeth

Key-Woodruff

Retainer-Spring, load brake

Spring-load brake (Plain-no color code)

Spring-load brake (Yellow color code)

Pin-Grooved

Cam-load brake

Gear & Clutch Assembly-load brake

For use with 1/4 H.P. Motor

For use with 1 /2 H.P. Motor

For use with 1 H.P. Motor

Disc-Friction, load brake

Bushing—Ratchet

Flange—load brake

Bearing Assembly-Needle, 5/8" I.D.

Washer-Thrust, 5/8" I.D.

Ring-Snap, brake flange

Pawl & Ratchet Assembly-load brake (includes item 15)

Ring-Snap, sprocket gear

Gear-Sprocket

74 teeth

65 teeth

52 teeth

(Continued on following page)

Page 44

11898

Qty.

Req’d

1

1

1

1

1

1

1

1

1

1

2

2

1

1

1

1

1

1

1

2

2

1

1

Figure 9-6. GEARING AND LOAD BRAKE PARTS - Continued

Ref.

No.

23

24

25

27

28

29

30

31

32

33

34

35**

Part

Number

BH-1228

BH-1229

BH-1230

BH-1232

BH-1318

BH-1311

BH-1313

BH-1235

BH-1236

BH-1315

BH-1316

BH-1317

BH-4079

BH-4020

BH-4021

Description

Screw - Fillister Head Machine

Lockwasher- Spring Type

Plate - Retainer, Sprocket Bearing

Bearing Assembly- Ball, Sprocket

Ball Bearing On Later Model Hoists

Sprocket-Coil Chain (1/4" Dia. Wire)

Sprocket - Roller Chain (5/8" Pitch)

Bearing Assembly - Ball, Sprocket

Key - Woodruff

O-Ring

Seal Disk

Seal - Oil

Clutch Assembly - 1/4 hp

1/2 hp

1 hp

* This gear and clutch assembly should not be field disassembled. Replace assembly only as clutch pressure is preset at factory based on hoist capacity and motor H.P.

** Replaces items 9-16 on non-load brake equipped models

Qty.

Req’d

1

1

1

1

1

1

1

4

4

1

1

1

1

NOTES

Page 45

To enable us to expedite your parts order, always give Model and Catalog Number and Electric

Current of Hoist. (See nameplate.)

Figure 9-7. GEARING AND LOAD BRAKE PARTS (1 thru 3 Ton Hoists)

12

13

14

15

16

17***

18

19

20

21

22

23

24

25

26

27

28**

29

Ref.

No.

5

6

3

4

7

1

2

8

9

10

11

Part

Number

BH-1201

BH-1202

BH-1203

BH-1220

BH-1221

BH-1222

BH-1219

BH-1218

BH-1223

BH-1238

BH-1241

BH-1242

BH-1212

BH-1216

BH-1239

BH-1210

BH-1207

BH-1208

BH-1206

BH-1205

BH-1204

BH-1214

BH-1224

BH-1225

BH-1226

BH-1236

BH-1304

BH-1237

BH-1305

BH-1306

BH-1307

BH-1228

Description

Seal-Oil, motor shaft

Bearing Assembly-Ball, motor shaft

Ring-Retaining, Internal

Bearing Assembly-Needle, 5/8" I.D.

Washer-Thrust, 5/8" I.D.

Ring-Snap, brake flange

Flange-Load Brake

Disc-Friction, load brake

Pawl and Ratchet Assembly-Load Brake (includes item 15)

Bushing-Ratchet

Gear and Clutch Assembly-Load Brake

For use with 1 /2 H.P. Motor

For use with 1 and 2-1/2 H.P. Motors

Spring-Load Brake (Plain-no color code)

Cam-Load Brake

Retainer-Spring, Load Brake

Key-Woodruff

Shaft and Integral Pinion-Load Brake

14 teeth

23 teeth

Washer-Thrust, 11/16" I.D.

Bearing-Thrust, bronze

Bearing Assembly-Needle, 11 /16" I.D.

Pin-Grooved

Ring-Snap, intermediate gear

Gear-Intermediate

74 teeth

65 teeth

Key-Woodruff

Shaft and Integral Pinion-Intermediate

Bearing Assembly-Needle, 11/16" I.D.

Ring-Snap, sprocket gear

Gear-Sprocket

Spacer-Sprocket Gear

Screw-Fillister Head Machine

(Continued on following page)

Page 46

11899

1

1

1

2

2

1

1

2

1

1

1

1

1

4

1

1

1

1

Qty.

Req’d

2

1

1

2

1

1

1

1

1

2

1

Figure 9-7. GEARING AND LOAD BRAKE PARTS - Continued

Ref.

No.

30

31

33

34

35

36

37

38

39

40

41**

Part

Number

BH-1229

BH-1230

BH-1232

BH-1318

BH-1308

BH-1311

BH-1312

BH-1313

BH-1314

BH-1235

BH-1315

BH-1316

BH-1317

BH-4020

BH-4021

Description

Lockwasher - Spring Type

Plate - Retainer, Sprocket Bearing

Bearing Assembly - Ball, Sprocket

Ball Bearing On Later Model Hoists

Key -Woodruff, Sprocket

Sprocket - Coil Chain

1/4" Dia. Wire

5/16" Dia. Wire

Sprocket - Roller Chain

5/8" Pitch

3/4" Pitch

Bearing Assembly - Ball, Sprocket

O-Ring

Seal Disk

Seal - Oil

Clutch Assembly 1/2

Clutch Assembly 1 & 2-1/2

Qty.

Req’d

1

1

4

1

1

1

1

1

1

1

1

1

1

1

* This gear and clutch assembly should not be field disassembled. Replace assembly only as clutch pressure is preset at factory based on hoist capacity and motor H.P.

** Ref. No. 41 is replaced by Ref. Nos. 7 thru 14 on non-load brake equipped hoists.

*** Ref. No. 17 occurs next to Ref. No. 16 for 14 tooth pinion shaft only.

NOTES

Page 47

25

23 24

20

22

21

19

To enable us to expedite your parts order, always give Model and Catalog Number and Electric

Current of Hoist. (See nameplate.)

11900J

Figure 9-8. ELECTRICAL CONTROL UNITS (Three phase Single Speed Hoists)

9

10

11

12

13

Ref.

No.

1

2

3

4

8

Part

Number Description

BH-3800

BH-3801

BH-3802

BH-2155

BH-3803

BH-3804

BH-2189

BH-2166

BH-3805

BH-2168

BH-2169

BH-3806

BH-2172

Contactor and Mounting Plate Assembly (Includes Ref. Nos. 1, 3 and 4)

Three Phase 24V Control

Three Phase 115V Control

Mounting Plate - Contactor

Sems Round Head Machine Screw with External Lock Washer (#10-24 x 3/8)

Contactor Assembly

Three Phase 24V Control

Three Phase 115V Control

Pan Head Self Tapping Screw (#8-32 x 1/2)

Transformer

Three Phase 208V/24V

Three Phase 230V/460V/24V

Three Phase 575V/24V

Three Phase 208V/115V

Three Phase 230V/460V/115V

Three Phase 575V/115V

BH-2173 Sems Round Head Machine Screw with External Lock Washer (1/4-20 x 5/8)

BH-2174

BH-2175

Plain Washer (Type N 1/4)

Grommet

See Fig. 9-12 Push Button Station and Conductor Cable Assembly

Fuse, Fuse Holder and Wire Assembly

BH-2176 3A/250V

BH-2177

BH-2178

BH-2179

1/2A/250V

Fuse Only

3A/250V Rating

1/2A/250V Rating

(Continued on following page)

Page 48

Qty.

Req’d

1

1

5

1

2

1

1

1

1

2

1

1

1

Figure 9-8. ELECTRICAL CONTROL UNITS - Continued

Ref.

No.

14

15

16

17

19

20

21

22

23

24

25

Part

Number

BH-3807

BH-2181

BH-2182

BH-3808

BH-4022

BH-4023

BH-2189

BH-2155

BH-4024

BH-4025

BH-4026

Description

Block-Terminal

Spacer-Terminal Block

Regular Helical Spring Lock Washer (#8 Pltd.)

Round Head Machine Screw (#8-32 x 1 Pltd.)

Electronic Limit Switch Controller

Controller Mounting Bracket

Self Tapping Screws

Sems Round Head Machine Screw with External Lock Washer (#10-24 x 3/8)

Proximity Sensor

Jam Nut-Plated - 7/16-20

Spacer Washer - Proximity Sensor

Note: Replacement fuses are standard automotive type and may be purchased locally.

NOTES

Qty.

Req’d

1

2

1

2

2

1

2

2

2

2

1

Page 49

To enable us to expedite your parts order, always give Model and Catalog Number and Electric

Current of Hoist. (See nameplate.)

25

23 24

20

22

21

19

11900K

Figure 9-9. ELECTRICAL CONTROL UNITS (Two Speed Hoists Only)

9

10

11

1

2

3

Ref.

No.

4

8

Part

Number Description

BH-3800

BH-3801

BH-3802

BH-2155

Contractor and Mounting Plate Assembly (Includes Ref. Nos. 1, 3 and 4)

Three Phase 24V Control

Three Phase 115V Control

Mounting Plate - Contactor

Sems Round Head Machine Screw with External Lock

Washer (#10-24 x 3/8)

Contactor Assembly

Three Phase 24V Control

Three Phase 115V Control

BH-3803

BH-3804

BH-2189

BH-2166

BH-2164

BH-2167

BH-2168

BH-2169

BH-2170

BH-2171

BH-2172

Pan Head Self Tapping Screw (#8-32 x 1/2)

Transformer

Three Phase 208V/24V

Three Phase 230V/24V

Three Phase 460V/24V

Three Phase 575V/24V

Three Phase 208/115V

Three Phase 230V/115V

Three Phase 460V/115V

Three Phase 575V/115V

BH-2173 Sems Round Head Machine Screw with External Lock

Washer (1/4-20 x 5/8)

BH-2174 Plain Washer (Type N 1/4)

See Fig. 9-13 Push Button Station and Conductor Cable Assembly

(Continued on following page)

Page 50

Qty.

Req’d

1

1

5

1

2

1

1

2

1

Figure 9-9. ELECTRICAL CONTROL UNITS - Continued

Ref.

No.

12

13

14

15

Part

Number

BH-2176

BH-2177

BH-2178

BH-2179

BH-3809

BH-3810

BH-3811

BH-2193

BH-3812

BH-3813

BH-2199

Description

Fuse, Fuse Holder and Wire Assembly

3A/250V

1/2A/250V

Fuse Only

3A/250V Rating

1/2A/250V Rating

Contactor and Mounting Plate Assembly (Includes

Ref. Nos. 13, 15 and 16)

Three Phase 24V Control

Three Phase 115V Control

Mounting Plate - Contactor

Sems Round Head Machine Screw with External Lock

Washer (#8-32 x 1/2)

Contactor Assembly

Three Phase 24V Control

Three Phase 115V Control

Pan Head Self Tapping Screw (#8-32 x 3/8) 16

Note: Replacement fuses are standard automotive type and may be purchased locally.

NOTES

1

1

2

1

2

Qty.

Req’d

1

1

Page 51

25

23 24

20

22

21

19

To enable us to expedite your parts order, always give Model and Catalog Number and Electric

Current of Hoist. (See nameplate.)

11900J

Figure 9-10. ELECTRICAL CONTROL UNITS (Single Phase Hoists)

1

2

3

Ref.

No.

4

8

9

10

11

12

Part

Number Description

BH-3800

BH-3801

BH-3814

BH-3815

BH-3802

BH-2155

BH-3803

BH-3804

BH-3816

BH-3817

BH-2189

BH-3818

BH-3819

BH-2173

Contractor and Mounting Plate Assembly (Includes Ref. Nos. 1, 3 and 4)

1/4, 1/2 & 1 HP

Single Phase 24V Control

Single Phase 115V Control

2-1/4 HP Only

Single Phase 24V Control

Single Phase 115V Control

Mounting Plate - Contactor

Sems Round Head Machine Screw with External Lock

Washer (#10-24 x 3/8)

Contactor Assembly

1/4, 1/2 & 1 HP

Single Phase 24V Control

Single Phase 115V Control

2-1/4 HP Only

Single Phase 24V Control

Single Phase 115V Control

Pan Head Self Tapping Screw (#8-32 x 1/2)

Transformer

Single Phase 115V/230V/24V

Single Phase 115V/230V/115V

Sems Round Head Machine Screw with External Lock

Washer (1/4-20 x 5/8)

BH-2174

BH-2175

Plain Washer (Type N 1/4)

Grommet

See Fig. 9-12 Push Button Station and Conductor Cable Assembly

(Continued on following page)

Page 52

Qty.

Req’d

1

1

2

1

1

2

1

1

4

1

Figure 9-10. ELECTRICAL CONTROL UNITS - Continued

Ref.

No.

13

14

15

16

17

Part

Number

BH-2176

BH-2177

BH-2178

BH-2179

BH-3807

BH-2181

BH-2182

BH-3820

Description

Fuse, Fuse Holder and Wire Assembly

3A/250V

1/2A/250V

Fuse Only

3A/250V Rating

1/2A/250V Rating

Block-Terminal

Spacer-Terminal Block

Regular Helical Spring Lock Washer (#8 Pltd.)

Pan Head Self Tapping Screw (#8-32 x 5/8 Pltd.)

Note: Replacement fuses are standard automotive type and may be purchased locally.

NOTES

Qty.

Req’d

1

1

2

2

1

2

Page 53

12763

To enable us to expedite your parts order, always give Model and Catalog Number and Electric

Current of Hoist. (See nameplate.)

Figure 9-12. PUSH BUTTON STATION AND CONDUCTOR CABLE ASSEMBLY (Single Speed Hoists)

Ref.

No.

11

12

13

14

15

16

17

8

9

6

7

10

3

4

1

2

5

Page 54

Part

Number

BH-3401

BH-3402

*

*

*

BH-3403

*

BH-3404

BH-3405

*

*

*

*

*

*

BH-3406

*

BH-3407

BH-3408

Description

Push Button Station and Conductor Cable Assembly

(Includes Ref. Nos. 1 thru 17)

Push Button Station (Includes Ref. Nos. 1 thru 15)

Type 1 Pan Head Machine Screw (M3.5 x 0.6 x 12 Pltd.)

Lockwasher (M 3.5 Pltd.)

Rear Cover

Gasket

Type l Pan Head Thread Cutting Screw (M 4 x 15 Pltd.)

Contact Assembly

Button Assembly

Type 1 Pan Head Machine Screw (M 6 x 1 x 12 Pltd.)

Lockwasher (M 6 Pltd.)

Plain Washer (M 6 Pltd.)

Type 1 Pan Head Machine Screw (M 3.5 x 1 x 14 Pltd.)

Lockwasher (M 3.5 Pltd.)

Housing Cap

Grommet

Housing

Conductor Cable Assembly

Plastic Warning Tag

* Not available separately. Order Push Button Station.

Qty.

Req’d

1

1

2

2

1

1

1

1

1

1

1

1

1

1

7

7

2

1

1

To enable us to expedite your parts order, always give Model and Catalog Number and Electric

Current of Hoist. (See nameplate.)

12721A

Figure 9-13. PUSH BUTTON STATION AND CONDUCTOR CABLE ASSEMBLY

(Two Speed Hoists Only)

Ref.

No.

4

5

6

7

8

1

2

3

Part

Number

BH-4027

BH-1981

BH-1982

BH-1971

BH-4029

BH-4030

*

*

BH-3403

BH-4028

Description

Push Button Station and Conductor Cable Assembly

(Includes Ref. Nos. 1 thru 30)

Grommet

Conductor Cable

Operator Warning Label

Push Button Station (Includes Ref. Nos. 12 thru 30)

Control Station Grommet

Control Station Hardware

Control Station Housing

Gasket

Button and Control Assembly

Contact Block

Contact Block

* Not available separately. Order Push Button Station.

** Not available separately. Order Push Button Assembly.

Qty.

Req’d

1

4

1

1

4

1

1

1

2

2

1

1

Page 55

To enable us to expedite your parts order, always give Model and Catalog Number and Electric

Current of Hoist. (See nameplate.)

12724B

Figure 9-14. SINGLE PHASE MOTOR ASSEMBLY

Ref.

No.

1

4

5

2

3

6

7

8

9

10

11

12

Part

Number

BH-4031

BH-4032

BH-4033

BH-3903

*

*

*

*

BH-3908

*

*

BH-3909

BH-3910

BH-3911

BH-3913

BH-3914

BH-3915

*

*

*

BH-3919

BH-3920

Description

Motor Assembly (Includes Ref. Nos. 1 thru 12)

1/4 Horsepower - Yellow Powercoat

1/2 Horsepower - Yellow Powercoat

1 Horsepower - Yellow Powercoat

2-1/4 Horsepower

Bell - End

Ring - Retaining

Bearing - Ball

Ring - Retaining

Key - Brake

Rotor and Shaft Assembly

Stator Assembly

Bolt - Motor Mounting

1/4 Horsepower

1/2 Horsepower

1 Horsepower

Capacitor Assembly

1/4 Horsepower

1/2 Horsepower

1 Horsepower

Cover

For Ref. No. 9

1/4 Horsepower

1/2 Horsepower

1 Horsepower

For Ref. No. 12

Slotted Hex Head Self Tapping Screw (#8-32 x 5/16)

Solid State Switch Assembly

1/4, 1/2 & 1 Horsepower BH-3921

* Furnished only as part of motor assembly.

Primer

BH-4034

BH-4035

BH-4036

Qty.

Req’d

1

1

1

1

1

1

1

1

1

1

4

2

1

Page 56

To enable us to expedite your parts order, always give Model and Catalog Number and Electric

Current of Hoist. (See nameplate.)

12724

Figure 9-15. THREE PHASE MOTOR ASSEMBLY

BH-4037

BH-4038

BH-4039

BH-4053

BH-4054

BH-4055

BH-4059

BH-4060

BH-4061

BH-4065

BH-4066

BH-4067

BH-4071

BH-4072

BH-4073

BH-4074

BH-4079

BH-4080

BH-4081

BH-4082

BH-4087

BH-4088

BH-4089

BH-4090

*

*

*

Ref.

No.

Part

Number

1

Description

Motor Assembly (Includes Ref. Nos. 1 thru 8)

1/4 Horsepower (1 Speed) - Yellow Powercoat

200 Volt

230/460 Volt

575 Volt

1/2 Horsepower (1 Speed) - Yellow Powercoat

200 Volt

230/460 Volt

575 Volt

1 Horsepower (1 Speed) - Yellow Powercoat

200 Volt

230/460 Volt

575 Volt

2-1/2 Horsepower (1 Speed) - Yellow Powercoat

200 Volt

230/460 Volt

575 Volt

1/2-1/6 Horsepower (2 Speed) - Yellow Powercoat

200 Volt

230 Volt

460 Volt

575 Volt

1-1/3 Horsepower (2 Speed) - Yellow Powercoat

200 Volt

230 Volt

460 Volt

575 Volt

2-1/4 - 3/4 Horsepower (2 Speed) - Yellow Powercoat

200 Volt

230 Volt

460 Volt

575 Volt

Bell - End

1 Speed - 1/4, 1/2 and 1 HP

1 Speed - 2-1/2 HP

2 Speed

(Continued on following page)

Primer

BH-4050

BH-4051

BH-4052

BH-4056

BH-4057

BH-4058

BH-4062

BH-4063

BH-4064

BH-4068

BH-4069

BH-4070

BH-4075

BH-4076

BH-4077

BH-4078

BH-4083

BH-4084

BH-4085

BH-4086

BH-4091

BH-4092

BH-4093

BH-4094

Qty.

Req’d

1

1

Page 57

Figure 9-15. THREE PHASE MOTOR ASSEMBLY - Continued

Ref.

No.

2

Part

Number

3

4

5

6

7

8

*

*

*

BH-3312

BH-2915

BH-2915

*

*

*

BH-3314

BH-2917

BH-2917

*

*

BH-3315

BH-2954

BH-2942

* Furnished only as part of motor assembly.

Ring - Retaining

1 Speed- 1/4, 1/2 and 1 HP

1 Speed - 2-1/2 HP

2 Speed

Bearing - Ball

1 Speed - 1/4, 1/2 and 1 HP

1 Speed - 2-1/2 HP

2 Speed

Ring - Retaining

1 Speed - 1/4, 1/2 and 1 HP

1 Speed - 2-1/2 HP

2 Speed

Key - Brake

1 Speed - 1/4,1/2 and 1 HP

1 Speed - 2-1/2 HP

2 Speed

Rotor and Shaft Assembly

Stator Assembly

Bolt - Motor Mounting

1 Speed - 1/4, 1/2 and 1 HP

1 Speed - 2-1/2 HP

2 Speed

Description

NOTES

1

1

1

1

4

Qty.

Req’d

1

1

Page 58

Coil Kit

Solenoid Kit

Figure 9-16. HOIST MOTOR BRAKE

Part No.

BH-4040

BH-4041

BH-4042

BH-4043

BH-4044

BH-4045

BH-4046

BH-4047

BH-4048

BH-4043

BH-4044

BH-4045

BH-4046

BH-4047

BH-4048

Ref. No.

4

Motor HP

1/4

1/2

1

2-1/4

2-1/2

Part No.

BH-5004

BH-5005

BH-5006

BH-5007

BH-5008

1

Motor RPM

1800

1800

1800

3600

3600

Voltage

115/230 1

Ø

230/460

575

115/230 1

Ø

230/460

575

115/230 1

Ø

230/460

575

115/230 1

Ø

230/460

575

115/230 1

Ø

230/460

575

Description

Solenoid Kit

Friction Disc

Brake Hub (not shown)

Brake Cover - Yellow Power Coat (not shown)

Brake Cover - Primer (not shown)

Coil Kit

BH-4097

BH-4095

BH-4096

BH-5000

BH-4098

BH-4099

BH-5003

BH-5001

BH-5002

BH-5000

BH-4098

BH-4099

BH-5003

BH-5001

BH-5002

Brake Torque ft. - lbs.

1-1/2

3

6

3

6

Page 59

Recommended Spare Parts for Your Yale Hoist

Certain parts of your hoist will, in time, require replacement under normal wear conditions.

It is suggested that the following parts be purchased for your hoist as spares for future use.

Set of Gaskets

Set of Bearings

Set of Oil Seals

Lower Block Assembly

Load Chain

Set of Brake Discs for Load Brake

Set of Brake Discs for Motor Brake

Push Button Station & Cable Assembly

Transformer

Contactor

Transformer Fuse

Limit Lever

Limit Switch Assembly

Note: When ordering parts always furnish Model and Catalog Number of Hoist and lift of hoist on which the parts are to be used.

Parts for your hoist are available from your local authorized Yale repair station.

For the location of your nearest repair station, write:

IN USA

Yale

Ÿ

Lift-Tech

P.O. Box 769

Muskegon, MI 49443-0769

Phone: 800 742-9269

Fax:

800 742-9270

WARRANTY

WARRANTY AND LIMITATION OF REMEDY AND LIABILITY

A. Seller warrants that its products and parts, when shipped, and its work (including installation, construction and start-up), when performed, will meet applicable specifications, will be of good quality and will be free from defects in material and workmanship. All claims for defective products or parts under this warranty must be made in writing immediately upon discovery and in any event, within one (1) year from shipment of the applicable item unless Seller specifically assumes installation, construction or start-up responsibility. All claims for defective products or parts when Seller specifically assumes installation, construction or start-up responsibility and all claims for defective work must be made in writing immediately upon discovery and in any event, within one (1) year from completion of the applicable work by Seller, provided; however, all claims for defective products and parts must be made in writing no later than eighteen (18) months after shipment. Defective items must be held for Seller’s inspection and returned to the original f.o.b. point upon request. THE

‘FOREGOING IS EXPRESSLY IN LIEU OF ALL OTHER

WARRANTIES WHATSOEVER, EXPRESS, IMPLIED AND

STATUTORY, INCLUDING, WITHOUT LIMITATION, THE IMPLIED

WARRANTIES OF MERCHANTABILITY AND FITNESS.

B. Upon Buyer’s submission of a claim as provided above and its substantiation, Seller shall at its option either (i) repair or replace its product, part or work at either the original f.o.b. point of delivery or at

Seller’s authorized service station nearest Buyer or (ii) refund an equitable portion of the purchase price.

C. This warranty is contingent upon Buyer’s proper maintenance and care of Seller’s products, and does not extend to normal wear and tear. Seller reserves the right to void warranty in event of Buyer’s use of inappropriate materials in the course of repair or maintenance, or if Seller’s products have been dismantled prior to submission to Seller for warranty inspection.

D. The foregoing is Seller’s only obligation and Buyer’s exclusive remedy for breach of warranty and is Buyer’s exclusive remedy hereunder by way of breach of contract, tort, strict liability or otherwise.

In no event shall Buyer be entitled to or Seller liable for incidental or consequential damages. Any action for breach of this warranty must be commenced within one (1) year after the cause of action has accrued.