Spec Sheet: Noyes SMLP5
SMLP5-5 Single-mode/Multimode Test
Kit with Wave ID, Set Reference, and
Data Storage
The SMLP5-5 test kit combines the OPM5-2D optical power meter and OLS4 integrated
LED and LASER light source and is ideally suited for testing fiber optic networks with
hybrid (single-mode and multimode) cables.
Features
•• Handheld, rugged, lightweight
•• Wave ID (auto identification & switching)
•• Dual or single Wave ID, CW, Tone
•• 270 Hz, 330 Hz, 1 kHz, 2 kHz Tone
•• Large LCD with backlight (OPM5-2D)
•• Power measurements in dBm or μW;
insertion loss in dB
•• Reference power level storage
•• Up to 500 records per wavelength storage
•• USB port for download of stored records
•• Windows® compatible software to view,
print, and archive stored records
•• Low battery indicator
•• Long battery life with 2 x AA alkaline,
optional AC adapter
•• Free 50 µm and 62.5 µm mandrels
•• Cost-effective, easy to use
•• N.I.S.T traceable
The OLS4 features 850/1300 nm LED output from a multimode output port and
1310/1550 nm LASER output from a single-mode output port. Each wavelength may be
transmitted individually at CW or with user selectable modulated Tone (SM output). Also,
each wavelength may be transmitted with Wave ID. When transmitting with Wave ID, the
OLS4 supports transmitting pairs of wavelengths in an alternating pattern. Associated
with each operating condition, the designated LED indicator will illuminate to identify the
currently enabled operating mode and emitted wavelength(s) along with battery charge
status and external power presence. Both output ports are equipped with UCI based
removable adapters to allow the output connectors to be inspected and cleaned.
The OPM5-2D features automatic wavelength identification and switching (Wave ID) when
used with the OLS4, multiple test Tone detection for fiber identification, and stores optical
references for each calibrated wavelength and up to 500 records per wavelength of power
or insertion loss measurements. Using the supplied Windows® compatible software and
USB connection, test records are transferred to a PC for analysis, printing, and storage.
A large dual-wavelength LCD display with backlight shows measured power [dBm or µW]
or insertion loss [dB], calibrated wavelengths [nm], tone signal [Hz], wavelength ID, and
estimated remaining battery life. The OPM5-2D optical input port accepts a variety of
Noyes thread-on style adapter caps (ordered separately) to meet a wide range of testing
requirements.
The OPM5-2D or OLS4 offer long battery life from common AA alkaline batteries with
external AC adapter available as an option.
The SMLP5-5 test kit is fully N.I.S.T. traceable.
Applications
•• Certify multimode and single-mode links per TIA/EIA standards
•• Fiber identification prior to splicing
Ordering Information
Model
Includes
SMLP5-5
OLS4 optical light source, OPM5-2D optical power meter, AA batteries, protective rubber boots,
adapter cap, USB cable, Windows® compatible software and user's guide, 50 and 62.5µm
mandrels, SMLP5-5 test kit user's guide, and carry case
Test jumpers and connector adapters are required for operation (purchased separately).
Test jumpers with a variety of connector styles and fiber types and adapter caps for most
common connectors may be purchased from AFL Telecommunications.
continued on the next page
© 2002-2009, AFL Telecommunications, all rights reserved. SMLP-55-2001 Revision D, 2009-06-16
Specifications are subject to change without notice.
1
SMLP5-5 Single-mode/Multimode Test Kit with Wave ID, Set
Reference, and Data Storage
OLS4 Light Source specifications
Optical
Wavelength
Emitter type
Spectral width
Output power
Output Stability
MM Optical Port
SM Optical Port
850 ± 30 nm
1300 -10/+50 nm
1310 ± 20 nm
1550 ± 20 nm
LED
Laser
Class I FDA 21 CFR 1040.10 and 1040.11, IEC 60825-1: 2007-03
40 nm (typ)
120 nm (typ)
5 nm (max)
5 nm (max)
0 dBm, 9 µm single-mode
> - 20 dBm, 62.5 µm multimode*
± 0.1 dB over 8 hours
± 0.05 dB over 1 hour (after 15 min. warm-up)
(after 5 min. warm-up)
± 0.1 dB over 8 hours (after 15 min. warm-up)
General
Power
Battery life
Available adapters
Operating temperature
Storage temperature
Size (H x W x D)
Weight
2 x AA batteries, optional AC adapter
Typical 30 hours, minimum 20 hours
Typical 72 hours, minimum 40 hours
SC FC, ST, LC
-10 to 50°C, 90% RH (non-condensing)
-30 to 60°C, 90% RH (non-condensing)
14.0 x 8.1 x 3.8 cm (5.5 x 3.2 x 1.5 in)
0.29 kg (0.65 lb)
* Output power will be approximately 3 dB less if a 50µm mandrel-wrapped jumper is used
instead of a 62.5µm mandrel-wrapped jumper.
All specifications at 25°C.
OPM5-2D specifications
Optical
Calibrated wavelengths
OPM5-2D
850, 1300, 1310, 1490, 1550 nm
Detector type
Germanium (Ge)
Measurement range
+6 to -60 dBm
Tone detect range
+6 to -50 dBm
+6 to -45 dBm for 850nm
Wavelength ID range
+6 to -50 dBm
+6 to -45 dBm for 850nm
Accuracy*
Resolution
Measurement units
General
Power
Battery life
± 0.25 dB
0.01 dB
dB, dBm, μW
2 x AA batteries, optional AC adapter
300 hours
Operating temperature
-10 to 50°C, 90% RH (non-condensing)
Storage temperature
-30 to 60°C, 90% RH (non-condensing)
Size (H x W x D)
14.0 x 8.1 x 3.8 cm (5.5 x 3.2 x 1.5 in)
Weight
0.26 kg (0.58 lb)
* Accuracy measured at 25ºC and -10 dBm per N.I.S.T. standards.
All specifications at 25°C
© 2002-2009, AFL Telecommunications, all rights reserved. SMLP-55-2001 Revision D, 2009-06-16
Specifications are subject to change without notice.
2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement