KitchenAid KBFN506EBS 20.8-cu ft Built-In French Door Refrigerator Dimensions Guide
Add to my manuals2 Pages
advertisement
▼
Scroll to page 2
Bottom Mount Built-in Refrigerator PRODUCT DIMENSIONS PRODUCT MODEL NUMBERS KBBL206E KBBL306E KBBR206E KBBR306E KBFN402E KBFN406E KBFN502E KBFN506E ■ Height dimensions are shown with the leveling legs extended to ¹⁄₈" (3 mm) below the rollers. ■ Width dimensions were measured from trim edge to trim edge. IMPORTANT: Observe all governing codes and ordinances. Electrical: A 115 Volt, 60 Hz., AC only 15- or 20-amp fused, grounded electrical supply is required. It is recommended that a separate circuit serving only your refrigerator be provided. Use an outlet that cannot be turned off by a switch. Do not use an extension cord. A grounded 3 prong electrical outlet should be placed within 4" (10.2 cm) of the right side cabinets or end panel. Location: Do not install in a location where the temperature will fall below 55°F (13°C). It is recommended that you do not install the refrigerator near an oven, radiator, or other heat source. ■ Floor must support the refrigerator weight, more than 600 lbs. (272 kg), door panels, and contents of the refrigerator. ■ Ceiling height must allow for side tipping radius. See “Tipping Radius.” ■ Location should permit door to open fully. See “Door Swing Dimensions.” ■ Location must permit top grille removal. See “Opening Dimensions.” Water Supply: A cold water supply with water pressure between 30 and 120 psi (207 and 827 kPa) is required to operate the water dispenser and ice maker. If you have questions about your water pressure, call a licensed, qualified plumber. Reverse Osmosis Water Supply IMPORTANT: The pressure of the water supply coming out of a reverse osmosis system going to the water inlet valve of the refrigerator needs to be between 30 and 120 psi (207 and 827 kPa). ■ All installations must meet local plumbing code requirements. ■ The water shutoff should be located in the base cabinet on either side of the refrigerator or some other easily accessible area. The right-hand side is recommended. The access hole through the cabinet must be within ¹⁄₂" (12.7 mm) of the rear wall. NOTE: If the water shutoff valve is in the back wall behind the refrigerator, it must be at an angle so that the tube is not kinked when the refrigerator is pushed into its final location. FRONT VIEW 36" (91.4 cm) Single Door and French Door Models 42" (106.7 cm) Models *83³⁄₈" (211.8 cm) *83³⁄₈" (211.8 cm) 42¹⁄₄" (107.3 cm) 36¹⁄₄" (92 cm) * When leveling legs are fully extended to 1¹⁄₄" (3.2 cm) below rollers, add 1¹⁄₈" (2.9 cm) to the height dimensions. SIDE VIEW TOP VIEW 25 ³⁄₈" (64.5 cm) 41Width ¹⁄₄" A (105 cm) 23¹⁄₂ " (59.7 cm) Model Width A 36" (91.4 cm) 35 ¹⁄₄ " (89.5 cm) 42" (106.7 cm) 41¹⁄₄ " (105 cm) 25³⁄₈" (64.5 cm) 6" (15.2 cm) *83³⁄₈ " (211.8 cm) ■ The water line attached to the back of the refrigerator is 5' (1.5 m) long. 84" (213.4 cm) Power Cord 1" (2.54 cm) 6" (15.2 cm) 6" (15.2 cm) 24" (60.96 cm) min. *3¹⁄₂" (8.9 cm) DOOR SWING DIMENSIONS The location must permit the door to open a minimum of 90°. Allow 4¹⁄₂" (11.4 cm) minimum space between the side of the refrigerator and a corner wall. NOTE: More clearance may be required if you are using overlay panels or custom handles. 36" (91.4 cm) Single Door Models 36" (91.4 cm) French Door Models 42" (106.7 cm) Models 39³⁄₄" (101 cm) 23" (58 cm) max. 42³⁄₄" (108.6 cm) 51" (130 cm) 44¹⁄₄" (112.3 cm) 41" (104 cm) 59" (150 cm) 90˚ 110˚ 90˚ 110˚ 90˚ 110˚ 90˚ 110˚ 90˚ 110˚ 130˚ Page 1 of 2 Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice. Dimensions are for planning purposes only. For complete details, see Installation Instructions packed with product. Specifications subject to change without notice. Ref. W10721177A 12/4/14 OPENING DIMENSIONS TIPPING RADIUS To avoid tipping during use, the solid soffit must be within 1" (2.5 cm) maximum above the refrigerator. If the solid soffit is higher than 1" (2.5 cm) or one is not available, then the refrigerator must be braced. If anti-tip boards are needed, they must be installed to the rear wall studs so that the bottom of the anti-tip board is 84" (213.4 cm) from the floor. NOTE: Do not remove the foam gasket on top of the compressor cover unless removal is necessary to fit the unit under a soffit. Removal of the gasket will cause loss in cooling efficiency. Be sure there is adequate ceiling height to stand the refrigerator upright when it is moved into place. ■ The dolly wheel height must be added to the tipping radius when a dolly is used. ■ If needed, the tipping radius can be reduced. See “Reduce Tipping Radius.” Side Tipping Radius (36" [91.4 cm] Models) A B ¹⁄₂" A (1.3 cm) A. Gasket B. Compressor cover 90¹⁄₂" (229.9 cm) NOTE: If installing under a solid soffit, after installation raise the leveling legs so that the gasket is pressed snugly against the soffit. A. Tip this side only. Side Tipping Radius (42" [106.7 cm] Models) B Model Dimension B 36" (91.4 cm) 4" (10.2 cm) 42" (106.7 cm) 7¹⁄₂" (19 cm) NOTE: A clearance of ¹⁄₂" (1.3 cm) must be maintained above the top grille in order for the top grille to be removed. A 84" (213.4 cm) to bottom of solid soffit 77" (196 cm) A Width (see chart following) Model 36" (91.4 cm) Overlay NOTE: Flooring under refrigerator must be at same level as the room. 93" (236.2 cm) A. Tip this side only. Width A 35¹⁄₂" - 35³⁄₄" (90.2 cm - 90.8 cm) 35³⁄₄" - 36" (90.8 cm - 91.4 cm) 6" (15.2 cm) 42" 41¹⁄₂" - 41³⁄₄" (106.7 cm) (105.4 cm - 106.0 cm) 41³⁄₄" - 42" Overlay (106.0 cm - 106.7 cm) 6" (15.2 cm) 1" (2.54 cm) 6" (15.2 cm) 24" (60.96 cm) min. Page 2 of 2 Because Whirlpool Corporation policy includes a continuous commitment to improve our products, we reserve the right to change materials and specifications without notice. Dimensions are for planning purposes only. For complete details, see Installation Instructions packed with product. Specifications subject to change without notice. Ref. W10721177A 12/4/14
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project