XP-400 with RPXP4GT Keypad Program Manual

XP-400 with RPXP4GT Keypad Program Manual
XP-400 Programming Instructions
®
Note: These Programming Instructions are intended to be used in conjunction with WI1370,
please refer to WI1370 for additional information, instructions and definitions.
DEALER PROGRAM MODE
NOTE:
DEFAULTING THE PANEL
After 15 minutes of keypad inactivity the keypad
will emit a steady tone indicating the panel has
been left in Dealer Program Mode. Enter Dealer
Code to exit or press the B key to return to
Dealer Program mode.
1. Remove power from the panel.
2. Remove all wiring from terminal
15 (PGM) and terminal 3.
3. Connect terminal 15 (PGM) to
terminal 3.
4. Apply power to the XP-400
control panel.
5. After a few seconds the
ARMED, READY and HSYSTEM TROUBLE LEDs will flash.
6. The keypad will beep 3 times
indicating the panel default
values have been loaded.
7. Remove wiring between terminal
15 (PGM) and terminal 3.
8. Re-install original wiring for
terminal 15 (PGM) and terminal
3.
- KEYPAD KEY DEFINITIONS
Hexadecimal Data Entry
To Enter a hexadecimal digit
enter the following:
A=
B=
C=
A1
A2
A3
D=
E=
F=
Set Key
Press this key before
entering a Programming
Block Number.
A4
A5
A6
Blank Key
Press this key to disable all
features within a LED type
Programming Block or to blank out
digits in a Direct Entry type
Programming Block.
Scroll Key
Use this key to scroll
through data that has
been
entered
in
Programming Blocks.
Note: Any programming in
Dealer Options 1 [96] and
Dealer Options 2 [97] will not be
defaulted.
If Dealer Code
Lockout has been programmed
the panel will not default the
Dealer Code.
Dealer Code
Entering Dealer Program Mode
READY (OFF)
(4) (5) (6) (7)
NOTE:
Entering Dealer Program Mode is not permitted while the panel
is Armed, Reporting, or the Bell Output is on. To Enter Dealer
Mode while the Bell is ON or the panel is Reporting or Armed;
power up the panel and enter Dealer Mode within the first 3
minutes. Pressing the b key clears the 3 minute timer.
Exiting Dealer Program Mode
ARMED (ON)
Enter A 8
SYSTEM (FLASHING)
Indicates the panel is in Dealer
Program Mode. The panel is
ready for a programming block
number to be entered.
Default Dealer Code shown in parentheses
Dealer Code
ARMED (FLASHING)
READY (FLASHING)
Enter B A 8
SYSTEM (FLASHING)
Indicates the panel is Ready
to exit
Dealer Program
Mode.
Enter the Dealer
Code to exit.
(4) (5) (6) (7)
© NAPCO 2005
WI1371 1/05
Types of Programming Blocks
LED Programming Block
Enable features by pressing the key that corresponds to the associated feature; the LED will turn ON. To disable a feature press the key
again; the LED will turn OFF. To disable all features within a LED Type Programming Block press the D key; all LEDs will turn OFF.
1
LED Programming Block Example
Program zones 2 and 3 as Follower Zones.
02 Exit/Entry Follower
OFF
1. Enter Programming Block 02, by pressing
B (Beep), then 02 (Beep).
2. Press the 2 key to select zone 2.
3. Press the 3 key to select zone 3.
Zone 2 and Zone 3
LED Type
are
ON
Programming LEDs
indicat in g
that
Block
zones 2 and 3 have
been programmed
as follower zones.
Default
OFF
OFF
OFF
!
!
Zone 1
Zone 2
Zone 3
Zone 4
Direct Entry Programming Block
Enter data directly. For hexadecimal entries of A-F, use the A key + 1 through 6 keys, respectively. Use the D key to blank out
digits in Direct Entry type programming blocks. Default values are shown in parentheses.
1
Direct Entry Programming Example 1
Program the panel for a 60 second Exit Delay.
1. Press B (Beep) 10 (Beep)
2. Press 060.
10 Exit Delay
0
6
0 Exit Delay, seconds
(0) (4) (5) Maximum Entry 255
44 Dialing Prefix
2
2
9
E
Direct Entry Programming Example 2
(Hexadecimal data entry)
Program Telephone Prefix Number with a 9E.
1.
2.
3.
4.
Press B (Beep) 44 (Beep).
Press 9
Press A
Press 5
Direct Entry
Type
Programming
Blocks
ARMED (OFF)
READY (FLASHING)
SYSTEM (FLASHING)
Indicates the panel is in
Dealer Program Mode and
the next digit entered will be
interpreted
as
a
Hexadecimal digit.
Valid
entries are 1-6 (A-F).
Viewing Data in Programming Blocks
To view data within a programming Block, enter the Program Block Number, then press the C key, continue pressing the C key until all digits within
the Programming Block have been viewed. Data will be displayed in the binary format shown in the table below:
0/Blank
1
2
3
4
5
6
7
8
9
*A/0
B
C
D
E
F
*
ZONE 1
ZONE 2
ZONE 3
ZONE 4
ZONE LED ON
For Technical
Assistance,
Contact the Napco
Toll Free Helpline
!
(800) 645-9440
44 Dialing Prefix
Press B44 to enter Programming Block 44. The 1st
digit of Programming Block 44 is displayed.
Press the B key to view the 2nd digit.
9
E
NOTE:
Data = 9
2
In
the
following
Programming Blocks, data
that has been entered as a
‘0’ will be displayed as an
‘A’:
Subscriber ID
Numbers,
Phone
Numbers, Pager Leading
and Trailing digits and
Report Codes.
ZONE LED OFF
Example: Viewing the Dialing Prefix
A Dialing Prefix of 9E has been programmed at Programming Block Number
44 (outside access number). Follow the steps below to view the data.:
1
NOTE:
The Following Programming
Options are not permitted for
UL installations: [05], [06], [232], [26-3] and [26-4].
T h e UL s y m b o l
by
a
programming Block indicates
the programming option is not
permitted for UL installations.
Data = E
NOTE:
For information about
programming blocks
refer
to
XP-400
Installation
Manual
WI1370.
3
Zone Features
03 Auto Bypass Reentry Zones
00 Exit/Entry Zones
Default
Default
06 Open Circuit Zones
Default
ON
Zone 1
OFF
Zone 1
OFF
Zone 1
OFF
Zone 2
OFF
Zone 2
OFF
Zone 2
OFF
Zone 3
OFF
Zone 3
OFF
Zone 3
OFF
Zone 4
OFF
Zone 4
OFF
Zone 4
04 24 Hour Protection Zones
01 Home/Away with Delay Zones
Default
Default
Default
Zone 1
OFF
Zone 1
ON
Zone 1
OFF
Zone 2
OFF
Zone 2
ON
Zone 2
OFF
Zone 3
OFF
Zone 3
ON
Zone 3
OFF
Zone 4
OFF
Zone 4
ON
Zone 4
Default
UL
See wiring
diagram for
Open Circuit
wiring.
07 Burg (Steady) Output
OFF
02 Exit/Entry Follower Zones
4
UL
05 40 ms Loop Response Zones
Default
08 Programmable Output (PGM)
Default
OFF
Zone 1
OFF
Zone 1
ON
Zone 1
OFF
Zone 2
OFF
Zone 2
ON
Zone 2
OFF
Zone 3
OFF
Zone 3
ON
Zone 3
OFF
Zone 4
OFF
Zone 4
ON
Zone 4
System Times
System Features
10 Exit Delay
20 Keypad Features 1
Exit Delay, seconds
(0)
(4)
(5)
Maximum Entry 255
11 Entry Delay
Entry Delay, seconds
(0)
(3)
(0)
Maximum Entry 255
(5)
OFF
Zn 2 LED ON = AUX
ON
Zn 3 LED ON = *Keypad Panic (GG )
OFF
Zn 3 LED ON = Panic
OFF
Zn 4 LED ON = Test Timer
25 Programmable Output (PGM) Features 3
Default
ON
Zn 1 LED ON = Audible panic
OFF
Zn 1 LED ON = AC Fail
OFF
Zn 2 LED ON = Exit/Entry with Urgency
OFF
Zn 2 LED ON = Low Battery
ON
Zn 3 LED ON = Display Bypass (ARMED)
OFF
Zn 3 LED ON = *Trouble
OFF
Zn 4 LED ON = Disable Code Entry Beeps
OFF
Zn 4 LED ON = Armed
*See Note 3
26 Miscellaneous Features 2
Default
Test Timer, days
(1)
Zn 1 LED ON = Reserved
Zn 2 LED ON = *Keypad AUX (FF )
22 Miscellaneous Features 1
14 Test Timer Interval
(0)
OFF
OFF
Default
Maximum Entry 255
13 Reserved
(0)
Zn 1 LED ON = *Keypad Panic 2 (KK )
21 Keypad Features 2
Bell Time-out, minutes
(0)
Default
OFF
OFF
Zn 4 LED ON = *Ambush (4th User Code)
*See Note 1
12 Burg (Steady) Output Time-out
(0)
24 Programmable Output (PGM) Features 2
Default
Line Cut Time-to-Fail, seconds
Zn 1 LED ON = Abort Delay
OFF
Zn 1 LED ON = Momentary Keyswitch Arming
ON
Zn 2 LED ON = Easy Arm/Easy Exit
OFF
Zn 2 LED ON = Reserved
ON
Zn 3 LED ON = Swinger Shutdown
UL
OFF
Zn 3 LED ON = Inhibit Fail to Communicate
OFF
Zn 4 LED ON = Bell on Line Cut (Armed)
UL
OFF
Zn 4 LED ON = Inhibit Low Battery Display
23 Programmable Output (PGM) Features 1
Default
Maximum Entry 255
15 Line Cut Time-to-Fail (Disabled = 000)
Default
OFF
UL
OFF
Zn 1 LED ON = Audio Verification
OFF
Zn 2 LED ON = *Access Output (A 3)
OFF
Zn 3 LED ON = *Follow Keypad Sounder
OFF
Zn 4 LED ON = *Keyfob/Keyswitch Chirp
(0) (0) (0) Enable Feature-Valid Entries 10-255
16 Wireless Supervisory Timer
NOTE*See
1: Note 2
Additional programming required for reporting, see Blocks [36]&[56].
NOTE 2:
Cannot be programmed with any other Programmable Output (PGM) Feature.
Supervisory Timer, hours
(1) (2) Maximum Entry 26
NOTE 3:
Includes Bell Cut, Receiver Fail-to-Respond, Receiver Tamper, Receiver
JAM, Transmitter Low Battery and Transmitter Supervisory Faliure.
5
Telephone Number 1 Programming
30 Subscriber ID Number
34 Zone Report, Telco 1
37 System Reporting, Telco 1
Default
31 Telephone Number 1
NOTE:
A fixed Dial Tone Detection (E) is included prior to the Dialing Prefix (Block
Number 44). Programming an E is not required for Telco 1, Telco 2 and
Telco 3. If dial tone detection is not desired select No Dial Tone Detection
in Communicator Features (Block Number 46). Program a D if a 4 second
delay is required.
32 Receiver Format
[0]
[1]
[2]
[3]
[4]
[5]
[6]
[7]
Disabled
Ademco Slow
Radionics Slow
Silent Knight Fast
Universal High Speed
Reserved
Point ID
Pager
(4)
Default
ON
Zone 1
OFF
Zn 1 LED ON = AC Fail Report (15 min. report delay)
ON
Zone 2
ON
Zn 2 LED ON = Low Battery Report
ON
Zone 3
OFF
Zn 3 LED ON = *Trouble Report
ON
Zone 4
OFF
Zn 4 LED ON = Reserved
*See Note 2
35 Zone Restore Report, Telco 1
38 System Restore Report, Telco 1
Default
Default
OFF
Zone 1
OFF
Zn 1 LED ON = AC Restore Report
OFF
Zone 2
OFF
Zn 2 LED ON = Battery Restore Report
OFF
Zone 3
OFF
Zn 3 LED ON = Trbl Restore Report
OFF
Zone 4
OFF
Zn 4 LED ON = Reserved
39 Opening Closing Report, Telco 1
36 System Reporting, Telco 1
Default
Default
OFF
OFF
ON
Zn 1 LED ON = *KP Panic 2
(KK )
Zn 2 LED ON = *KP AUX (ff )/Ambush
Zn 3 LED ON = *KP Panic (gG )
OFF
Zn 4 LED ON = Test Timer
*See Note 1
OFF
Zn 1 LED ON = User 1 Reporting
OFF
Zn 2 LED ON = User 2 Reporting
OFF
Zn 3 LED ON = User 3 Reporting
OFF
Zn 4 LED ON = User 4 Reporting
33 Receiver Options
Default
6
ON
Zn 1 LED ON = 2300 Hz Handshake/Kissoff
OFF
Zn 2 LED ON = Sumcheck
OFF
Zn 3 LED ON = Single Digit
OFF
Zn 4 LED ON = No Handshake/Pager Extend
NOTE 1:
NOTE 2:
Requires features to be enabled, see block [20].
Includes Bell Cut, Receiver Fail-to-Respond, Receiver Tamper, Receiver
JAM, Transmitter Low Battery and Transmitter Supervisory Faliure.
ZONE 3 TX LOW BATTERY
“RF TRAN LOW BAT, ZN03”
Backup Telephone Programming
40 Subscriber ID Number (Telco 2)
44 Dialing Prefix
Dialing Prefix for Telco 1, Telco 2
& Telco 3.
41 Telephone Number 2
45 Communicator Features 1
Default
NOTE:
ON
Zn 1 LED ON = Communicator Enabled
A fixed Dial Tone Detection (E) is included prior to the Dialing Prefix (Block
Number 44). Programming an E is not required for Telco 1, Telco 2 and
Telco 3. If dial tone detection is not desired select No Dial Tone Detection
in Communicator Features (Block Number 46). Program a D if a 4 second
delay is required.
ON
Zn 2 LED ON = DTMF w/ Rotary Back up
OFF
Zn 3 LED ON = DTMF only
OFF
Zn 4 LED ON = Backup to Telco 2
42 Receiver Format
[1]
[2]
[3]
[4]
[5]
[6]
[7]
Ademco Slow
Radionics Slow
Silent Knight Fast
Universal High Speed
Reserved
Point ID
Pager
46 Communicator Features 2
Default
(4)
OFF
Zn 1 LED ON = No Dial Tone Detection
OFF
Zn 2 LED ON = 2:1 Rotary Dialing
OFF
Zn 3 LED ON = Backup if < 4 attempts
OFF
Zn 4 LED ON = Reserved
43 Receiver Options
Default
ON
Zn 1 LED ON = 2300 Hz Handshake/Kissoff
OFF
Zn 2 LED ON = Sumcheck
OFF
Zn 3 LED ON = Single Digit
OFF
Zn 4 LED ON = No Handshake
7
Telephone Number 3 Programming
50 Subscriber ID Number
54 Zone Report, Telco 3
57 System Reporting, Telco 3
Default
51 Telephone Number 3
NOTE:
A fixed Dial Tone Detection (E) is included prior to the Dialing Prefix (Block
Number 44). Programming an E is not required for Telco 1, Telco 2 and
Telco 3. If dial tone detection is not desired select No Dial Tone Detection
in Communicator Features (Block Number 46). Program a D if a 4 second
delay is required.
52 Receiver Format
[0]
[1]
[2]
[3]
[4]
[5]
[6]
[7]
Disabled
Ademco Slow
Radionics Slow
Silent Knight Fast
Universal High Speed
Reserved
Point ID
Pager
(4)
Default
OFF
Zone 1
OFF
Zn 1 LED ON = AC Fail Report (15 min. report delay)
OFF
Zone 2
OFF
Zn 2 LED ON = Low Battery Report
OFF
Zone 3
OFF
Zn 3 LED ON = *Trouble Report
OFF
Zone 4
OFF
Zn 4 LED ON = Reserved
*See Note 2
55 Zone Restore Report, Telco 3
58 System Restore Report, Telco 3
Default
Default
OFF
Zone 1
OFF
Zn 1 LED ON = AC Restore Report
OFF
Zone 2
OFF
Zn 2 LED ON = Battery Restore Report
OFF
Zone 3
OFF
Zn 3 LED ON = Trbl Restore Report
OFF
Zone 4
OFF
Zn 4 LED ON = Reserved
59 Opening Closing Report, Telco 3
56 System Reporting, Telco 3
Default
Default
OFF
OFF
OFF
Zn 1 LED ON = *KP Panic 2
(KK )
Zn 2 LED ON = *KP AUX (ff )/Ambush
Zn 3 LED ON = *KP Panic (gG )
OFF
Zn 4 LED ON = Test Timer
*See Note 1
OFF
Zn 1 LED ON = User 1 Reporting
OFF
Zn 2 LED ON = User 2 Reporting
OFF
Zn 3 LED ON = User 3 Reporting
OFF
Zn 4 LED ON = User 4 Reporting
53 Receiver Options
Default
8
ON
Zn 1 LED ON = 2300 Hz Handshake/Kissoff
OFF
Zn 2 LED ON = Sumcheck
OFF
Zn 3 LED ON = Single Digit
OFF
Zn 4 LED ON = No Handshake/Pager Extend
NOTE 1:
NOTE 2:
Requires features to be enabled, see block [20].
Includes Bell Cut, Receiver Fail-to-Respond, Receiver Tamper, Receiver
JAM, Transmitter Low Battery and Transmitter Supervisory Faliure.
ZONE 3 TX LOW BATTERY
“RF TRAN LOW BAT, ZN03”
Report Codes
60 Zone Report Codes
Zone 1 Alarm Code
(3)
Zone 2 Alarm Code
(3)
Zone 3 Alarm Code
62 Zone Codes
65 Opening and Closing Code
Zone 1, 2, 3 & 4 Restore Code
NOTE:
The second digit of the
Report Code is the number
of the zone that is reporting.
For example zone 5 report
code (default of 3) would be
35.
(3)
(E)
Zone 1, 2, 3 & 4 Trouble Code
(F)
(B) Opening Code
63 System Report Codes
Zone 4 Alarm Code
(C) Closing Code
(3)
66 Ambush Report Code
Keypad Panic 2 (KK)
(1)
(1)
Keypad AUX (FF)
(2)
(3)
(2)
(1)
(F)
(F)
(F)
(9)
(2)
(2)
Keypad Panic (GG)
Test Timer
AC Fail
61 Point ID Report Codes
(F)
(3)
Zone 2 Alarm Code
(3)
Zone 3 Alarm Code
(3)
Zone 4 Alarm Code
(3)
1
2
3
4
5
6
7
8
9
A
B
FIRE
PANIC
BURGLARY
HOLDUP
GENERAL ALARM
RESERVED
GAS ALARM
HEAT ALARM
RESERVED
AUXILIARY
24 HOUR ALARM
(8)
*Trouble
(F)
67 Telephone Number 1
Default
Low Battery
Zone 1 Alarm Code
Enhanced Communicator Features
(1)
OFF
Zn 1 LED ON = Opening after Alarm (Cancel Code)
OFF
Zn 2 LED ON = Conditional Closing
OFF
Zn 3 LED ON = Reserved
OFF
Zn 4 LED ON = Reserved
*See Note 1
68 Telephone Number 3
Default
64 System Restore Code
(E)
OFF
Zn 1 LED ON = Opening after Alarm (Cancel Code)
OFF
Zn 2 LED ON = Conditional Closing
OFF
Zn 3 LED ON = Reserved
OFF
Zn 4 LED ON = Reserved
NOTE 1:
Includes Bell Cut, Fire Trouble, Receiver Fail-to-Respond, Receiver Tamper,
Receiver JAM, Transmitter Low Battery and Transmitter Supervisory Faliure.
9
Wireless
Transmitters
RF ID #
Point
71 Zone 1
:
72 Zone 2
:
73 Zone 3
:
74 Zone 4
:
Programming Example
Enter the RF ID# located on
the Transmitter and Key Fob
labels.
RF ID # XXXXXX:X
Enter the point number to be
associated with the zone. If only
one point of GEM-TRANS2 is
used, enter a 1 in this location.
For GEM-GB, GEM-DT, GEMPIR enter a 1 in this location.
Keyfobs
RF ID #
81 Keyfob 1
82 Keyfob 2
AUX 1 AUX 2
:
:
Map point 1 of a window door transmitter, with RF ID# 0012B0:0
to Zone 3.
73 Zone 3
0
0
1
10
A= A 1
B= A 2
D= A 4
:0
3.Enter
0012A200
1
1
(beeps)
Hexadecimal B Entry
Note: If the RF ID# in step 3 is not entered correctly the
keypad will emit a 1 second tone indicating incorrect entry.
Repeat steps 2 - 4 above.
Panic
AUX
Bell ON
PGM
Instant
Access on PGM
Full Set System
Interior
C= A 3
0
4.Enter
Hexadecimal Data Entry
To Enter a hexadecimal digit enter the following:
B
1.Enter Dealer Mode.
2.Enter B (beeps) 7 3 (beeps)
AUX 1 & 2
Programming
1
2
3
4
5
6
7
8
2
E= A 5
F= A 6
Downloading
90 Callback Telephone Number
Dealer Programming
94 Dealer Code
97 Dealer Options 2
Default
(4) (5) (6) (7)
91 Ring Count
95 User 1 Code
OFF
Zn 1 LED ON = *International Dialing Protocol
OFF
Zn 2 LED ON = *Invert Bell Output
OFF
Zn 3 LED ON = System Trouble Auto Restore
OFF
Zn 4 LED ON = User 1 Code-Program only
*See Note 1
(0) (9) Maximum Entry 15
(1) (2) (3) (4)
92 Downloading Features
Default
ON
Zn 1 LED ON = Ring Method
ON
Zn 2 LED ON = Answering Machine override
ON
Zn 3 LED ON = Command 6(A6) Download
OFF
Zn 4 LED ON = Reserved
96 Dealer Options 1
98 Number of Re-Dials
Default
OFF
Zn 1 LED ON = Dealer Code Lockout
ON
Zn 2 LED ON = User 1 Code Lockout
OFF
Zn 3 LED ON = Reserved
OFF
Zn 4 LED ON = Reserved
(9)
NOTE 1:
International Features.
93 Auto Download ID Number
11
E1
XP-400 WIRING DIAGRAM
+ RED
(REFER TO INSTALLATION INSTRUCTIONS WI1371)
RECHARGEABLE
BATTERY
12 VDC 4AH OR 7AH
E2
BLACK
RESIDENTIAL BURG (4 HOUR STANDBY)
COMBINED STANDBY = 350 mA
BELL = 2.0 AMP
RECOMMENDED BATTERIES YUASA
NP4-12 AND NP7-12
REPLACE EVERY FIVE YEARS
COLD WATER GROUND
CONNECTION
USE ONLY COLD-WATER
PIPE OR BURIED
GROUND ROD. USE AT
LEAST #16 AWG WIRE.
NOT USED
1
2
+3
-4
+5
+6
-7
+8
-9
+10 -11 +12 -13
BELL
GND
2.2K
2.2K EOLR
ZONE 2
(SUPERVISED)
(E)
Normally Open Zone Wiring
(Z)
ZONE 4
2.2K
Wire the normally
open contact
as shown (Zone 4).
Program the
zone for
Open Circuit [06]
operation.
3.9K
(1) ALL ZONE RESISTORS MUST BE INSTALLED, EVEN IF ZONE
IS NOT USED.
(2) COMBINED STANDBY = KEYPAD CURRENT + AUX POWER
CURRENT + FIRE POWER + PGM CURRENT.
(3) DO NOT CONNECT TO SWITCHED OUTLET.
(4) UNIT INTENDED TO BE MOUNTED VERTICALLY ON WALL.
(5) THIS PANEL SHALL BE CHECKED BY A QUALIFIED
TECHNICIAN AT LEAST ONCE EVERY THREE YEARS.
(6) SYSTEM MUST BE TESTED AT LEAST ONCE A WEEK IN THE
AC/BATTERY MODE AND IN THE BATTERY-ONLY MODE.
(CONTACT CENTRAL STATION PRIOR TO TESTING) AC
MUST BE RESTORED AFTER TEST.
ZONE 1
(E)
ZONE 1
12
RING
(-)
(+)
GEM-RECV-XP8
12
+PWR
TELCO
PHONE
BRN
(E)
19
TIP
GRAY
(E)
2.2K
GOLD
WHITE RED
2.2K
ORANGE
18
RING
GRN
ZONE 4
17
TIP
RED
(1)
(Z)
16
Programmable
Output
ZONE 3
+
3.9K
RPXP4GT
15
PGM
LOAD
50 mA MAX.
(Z)
BLK
(Z)
AUX POWER OUTPUT 10-12.5 VDC
EARTH
GROUND
3.9K
GOLD
RED RED
GRN
+
3.9K
RED
14
GND GREEN
REMOTE BUS
(3)
Zone
DoublingTM
Resistors
+PWR
RED
(E)
EZ
TELE LINE IN USE
ALL OUTPUTS ARE CURRENT LIMITED
16 VAC 20 VA
TRANSFORMER
NAPCO TRF12
(OR EQUIVALENT
SEE WI1370).
Class 2
Transformer.
2.2K
DS1
To RJ31X
(Supervised)
WARNING
TO PREVENT RISK
OF ELECTRIC SHOCK
DISCONNECT TELEPHONE
LINES PRIOR TO
SERVICING
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement