Indoor Dome Camera

DWC-D1363D

DWC-D1363D922

ABOUT MANUAL

Before installing and using the camera, please read this manual carefully.

Be sure to keep it handy for future reference.

07132012

PRECAUTIONS

Do not open or modify.

Do not open the case except during maintenence and installation, for it may be dangerous and can cause damages.

Do not put objects into the unit.

Keep metal objects and flammable substances from entering the camera.

It can cause fire, short-circuits, or other damages.

Be careful when handling the unit.

To prevent damages, do not drop the camera or subject it to shock or vibration.

Do not install near electric or magnetic fields.

Protect from humidity and dust.

Protect from high temperature.

Be careful when installing near the ceiling of kitchen or a boiler room, as the temperature may rise to high levels.

Cleaning:

To remove dirt from the case, moisten a soft cloth with a soft detergent solution and wipe.

Mounting Surface:

The material of the mounting surface must be strong enough to support the camera.

FCC COMPLIANCE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference, when the equipment is operated in a residential environment. This equipment generates, uses, and radiates radio frequency energy; and if it is not installed and used in accordance with the instruction manual, it may cause harmful interference to radio communications.

WARNING: Changes or modifications are not expressly approved by the manufacturer.

2

TABLE OF CONTENTS

Introduction Features

Parts and Descriptions

Dimensions

Installation Inside the Box

Mount Installation Instructions

Connecting to Monitors

Adjusting the Camera Lens

Adjusting the 3-Axis Gimbal

Module OSD Menu

Troubleshooting

Warranty Information

Specifications

13-24

25

26-27

28-29

7

8-9

10

11

12

4

5

6

3

F

EATURES*

1/3” CCD

620 TV Lines (B&W), 600 TV Lines (Color)

3.3~12mm Varifocal Auto Iris Lens [DWC-D1363D Only]

9~22mm Varifocal Auto Iris Lens [DWC-D1363D922 Only]

Electronic Day and Night

Smart DNR (Digital Noise Reduction)

DRC (Dynamic Range Compressor)

Star-Light (Super Low Light Technology)

HME (Highlight Masking Exposure)

Programmable Privacy Zones & Motion Detection

Easy Icon Driven OSD Menu with Built-In Joystick

Auto Sensing 12VDC or 24VAC with Line Lock

RS-485 Built-in

Secondary Video-BNC Output

4

6

7

4

5

1

2

3

P

ARTS & DESCRIPTION*

Lens

Power Input Connector (12VDC/24VAC)

Primary Video-BNC Output Connector

Bottom Case

Mounting Screws

Outer Dome Cover

Assembly Screws

4

2

1

5

6

7

3

5

D

IMENSIONS IN MILLIMETERS (IN)*

7.0(0.28”)

5.0(0.2”)

88.0(3.46”)

46.5

(1.83”)

123.8(4.9”)

82.5(3.25”)

6

I

NSIDE THE BOX*

Included with D1 Indoor Dome Camera

1

2

3

User Manual

Mounting Template

2 Machine Screw and 2 Dry Wall Anchors

4

5

6

Miniature TORX Driver

L-Key

Secondary Video-BNC Cable

7

C

AMERA INSTALLATION*

1 Cut a hole in the ceiling for routing the cables. Use your mounting template to mark the screw holes.

2 Drill holes into the drywall and insert the drywall mounts into the holes.

3 Pull wires through and make connections.

4 Mount and secure the camera to the surface using the machine screws.

5 Position the lens and adjust the zoom and focus.

6 Assemble the outer dome cover with the camera module.

8

W

ALL MOUNT INSTALLATION*

1 Check to see all parts are in the box.

2 Use the mount to mark the pilot holes are required. Drill holes into the drywall and insert the drywall mounts.

3 Secure the wall mount to the wall using the mounting screws.

4 Attach the base of the camera to the wall mount with the smaller machine screws.

5 Position the lens and adjust the zoom and focus.

6 Assemble the outer dome cover with the camera module.

9

C

ONNECTING TO MONITORS*

DC12V / AC24V

Video Output BNC Cable

Main Monitor

10

A

DJUSTING THE CAMERA LENS*

Focus Handle

Zoom Handle

1

2

3

4

Loosen the zoom and focus handles by rotating them counter-clockwise.

Adjust the field of view by moving the handle to the RIGHT (tele) to zoom in or to the LEFT (wide) to zoom out.

AFTER the desired zoom position is established, adjust the focus the same way as described above.

Once the desired adjustments have been made, please tighten the handles back by turning them clockwise.

11

A

DJUSTING THE 3-AXIS GIMBAL*

12

60.0° Tilt 360.0° Pan

M

ODULE OSD MENU*

EXPOSURE COLOR

WB MODE

AWC / ATW / MANUAL /

PUSHLOCK

AGC

OFF / LOW / MID /

HIGH / HIGHEST

STARLIGHT

3D DNR

OFF / LOW / MID / HIGH /

SMART

DAY & NIGHT

MOTION PRIVACY SETUP

FUNCTION

ENGLISH / 繁體中文 / 简体中文 / 日本語 /

DEUTSCH / FRENCH / ITALIAN /

RUSSIAN / SPANISH / DUTCH

OSD COLOR

BLUE / GREEN / CYAN / RED /

MAGENTA / YELLOW / PURPLE /

GRAY

EXIT

SAVE & EXIT

EXIT

13

14

EXPOSURE

LENS

Manual

DC

Manual mode supports the fixed board lens or the manual iris lens.

DC mode supports the auto-iris varifocal lens.

NOTE: Both MANUAL and DC mode have FOCUS TARGET. You can adjust the focus by finding the highest number on the FOCUS

TARGET. See page 16 for focus information.

1/60

ELC Levels and DC Levels are adjustable. The higher the number, the brighter the image.

E. Shutter sets the shutter speed levels from 1/60 to 1/100000.

*For LENS-MANUAL Mode, the default E.SHUTTER is AUTO.

*For LENS-DC Mode, the default E.SHUTTER is 1/60. Select DC-AUTO for

* oudoor use.

Select 1/100FLC to run camera in flickerless mode.

Note: The STARLIGHT option cannot be controlled if the

E.SHUTTER setting is above 1/60.

EXPOSURE

BACKLIGHT

OFF

BLC

MANUAL

SMART

BACK LIGHT COMPENSATION

User can manually adjust the BLC level in five areas of the scene (TOP, BOTTOM,

CENTER, LEFT, RIGHT). Increase the BLC levels to make the image brighter.

This is recommended. Camera will automatically detect and adjust the BLC zone.

BLC levels to choose from include: LOWEST, LOW, MID, HIGH.

HME

DRC

HIGHLIGHT MASKING EXPOSURE

HME masks highlights to allow objects to appear clearly on the screen. If ON is selected, HME levels are adjustable. The lower the number, the darker the masking areas.

DYNAMIC RANGE COMPRESSOR

With the advanced light compensation technology DRC, dark spots in images particularly become more visible without overexposing the bright spots to create one perfect image.

The higher the number, the better the performance of DRC.

15

EXPOSURE

AGC

OFF / LOW / MID / HIGH / HIGHEST

AUTO GAIN CONTROL

AGC enhances the picture brightness in low light conditions.

A higher level AGC setting makes the images brighter; however, it could increase the amount of noise.

STARLIGHT

OFF / x2 ~ x1024

3D DNR

OFF / LOW / MID / HIGH / SMART

EXIT JUMP

SAVE & EXIT

EXIT

Starlight mode automatically activates slow shutter function when the image is too dark. x4 is the default. We do not recommend you to increase the setting, for it causes the image to lag.

Note: Starlight menu cannot be controlled if the E.SHUTTER setting is above 1/60.

3D DIGITAL NOISE REDUCTION

3D-DNR reduces the noise on the screen in low light conditions and allows for clearer images, even at night. The SMART option will adjust the camera to prevent lagging when there is motion.

Save the current settings and exit the OSD menu.

Exit the OSD menu without saving the changes.

16

COLOR

WB MODE

AWC

ATW

Auto White Balance Control mode compensates for color temperature changes between 2000K and 18000K.

Auto Tracking White Balance Control mode compensates for color temperature changes between 2500K and 9500K.

MANUAL Users can control the white balance manually by

PUSHLOCK changing RED GAIN and BLUE GAIN (see below).

Pushlock is to fix the white balance based on the lighting.

RED GAIN

0 ~ 255 Adjusts the amount of red in the image.

BLUE GAIN

0 ~ 255 Adjust the amount of blue in the image.

COLOR MODE

NORMAL Color is similar to actual color.

COOL

WARM

Color has more blue.

Color has more red.

EXIT JUMP

SAVE & EXIT

EXIT

Save the current settings and exit the OSD menu.

Exit the OSD menu without saving the changes.

17

DAY & NIGHT

D&N MODE

AUTO /

COLOR /

B&W

In AUTO mode, camera switches between day and night automatically depending on light

level. Camera will stay in color mode when there is enough light and will switch to B&W at night or other low light environments. If COLOR is selected, camera always stays in day/color mode. If B&W is selected, camera always stays in night/B&W mode.

If AUTO is selected, please define the following settings:

*BURST: If ON is selected, the camera provides a color burst signal in night mode.

*COLOR->B&W: Adjusts the light level at which the camera switches from day (color) to night (B&W) mode. The higher the

* number, the lower the light level.

*B&W->COLOR: Adjusts the light level at which the camera switches from night (B&W) to day (color) mode. This number

* should be lower than the value of COLOR->B&W above.

*READ TIME: 3s~12s. Time interval delay before switching from day mode to night mode.

*EX_IR INT.: AUTO/EXT. If using IR LEDs built into the camera, select AUTO. If using external IR LEDs separately,

* select EXT.

NIGHT C.

0 ~ 100 Color will be reduced in low light conditions. (This level cannot be adjusted when

3D-DNR is ON.)

NIGHT A.

0 ~ 100 Edge sharpness will be reduced in low light conditions. (This level cannot be adjusted when 3D-DNR is ON.)

EXIT JUMP

SAVE & EXIT

EXIT

Save the current settings and exit the OSD menu.

Exit the OSD menu without saving the changes.

18

FUNCTION

MIRROR

OFF

MIRROR Flips the image horizontally.

SHARPNESS

0 ~ 30 Sets the image sharpness. The higher the number, the sharper the image.

GAMMA

0.45 / 0.60 /

1.0 / MANUAL

Select the desired gamma level. 0.45 is default setting.

SLC (SIDE LIGHT COMPENSATION)

OFF / ON Increase the brightness on sides of the image.

NIGHT-UP

OFF / ON Adjusts sensitivity in low light conditions by setup level. If ON is selected, the setup level becomes higher, and the images become brighter.

EXIT JUMP

SAVE & EXIT

EXIT

Save the current settings and exit the OSD menu.

Exit the OSD menu without saving the changes.

19

MOTION

The camera can detect the movement and display an alarm on the screen when movement is detected.

AREA SET

AREA 1 ~ 4

OFF / ON

If ON, motion areas can be selected and moved

accordingly. Select Areas 1-4 and adjust using controls for TOP, BOTTOM, LEFT, or RIGHT.

SENSITIV.

1 ~ 30 Sensitivity level of the motion detection is adjustable.

Motion Detection will be more sensitive at a higher number.

SHOW INDI.

OFF / ICON

TRACE

Set the Show Indicator to OFF, ICON, or TRACE. If ICON is selected, a bell will appear in the upper right hand corner when motion is detected. If TRACE is selected, the area where motion was detected will be highlighted.

EXTER OUT (ALARM SIGNAL, EXTERNAL OUTPUT)

OFF / ON If ON is selected, you can set how long (0~15s) the alarm is displayed on the screen when motion is detected.

EXIT JUMP

SAVE & EXIT

EXIT

Save the current settings and exit the OSD menu.

Exit the OSD menu without saving the changes.

20

PRIVACY

You can hide some parts of the screen for privacy masking.

A total of 8 different privacy masking zones are available.

MASK 1 ~ MASK 8

OFF / ON Select ON or OFF for each mask (MASK 1 through 8).

If ON is selected you can set the area to be masked and the shape and color of the mask.

*START POINT: Select the START POINT to adjust the size of the

* privacy zone.

* L_TOP (Left Top)

* R_TOP (Right Top)

* L_BOT (Left Bottom)

* R_BOT (Right Bottom)

*MODIFY: After selecting the START POINT, you can modify the

* size of the privacy zone by moving the joystick left or right.

*POSITION: You can move the privacy zone by moving the joystick

* left or right.

*COLOR SET:

* Privacy zones can be set with eight different colors-GRAY,

* BLACK, WHITE, RED, GREEN, BLUE, MAGENTA, and CYAN.

21

TITLE

OFF / ON

SETUP

If ON is selected, you can display the camera title on the screen.

*CLR: Clear the title.

*POS: Position the title on the screen.

DPC (DEAD PIXEL CANCELLATION)

OFF

AUTO

DPC automatically removes defective pixels in real time.

If AUTO is selected, you can define the following settings:

*WHITE THR: Cancels the white defective pixels.

*BLACK THR: Cancels the black defective pixels.

*DPC LEVEL: Adjusts the sensitivity level of the dead * pixel cancellation.

NOTE: Adjust the WHITE THR/BLACK THR and DPC LEVEL at the same time.

MONITOR

MODE 1-2 MODE 1 is the default. If the displayed image is not good enough, try MODE 2.

22

SETUP

LANGUAGE

The camera supports the following languages: ENGLISH, CANTONESE, MANDARIN, JAPANESE,

GERMAN, FRENCH, ITALIAN, RUSSIAN, SPANISH, AND DUTCH.

OSD COLOR

The following colors are available for the OSD menu: BLUE, GREEN, CYAN, RED, MAGENTA,

YELLOW, PURPLE, and GRAY.

COMMUNICATION

OFF

ON

*

*

If ON is selected, you can define the following:

*PROTOCOL: PELCO-D only.

*CAMERA ID: Provide an ID number for the camera

(0~255).

*BAUDRATE: 9600bps is the default. There are four options: 2400bps, 4800bps, 9600bps, and 19200bps.

FACTORY SET

If selected, the camera reverts back to factory default settings.

NOTE: FACTORY SET does not affect the LENS, DAY & NIGHT, CAMERA ID, and DPC SETTINGS.

EXIT JUMP

SAVE & EXIT

EXIT

Save the current settings and exit the OSD menu.

Exit the OSD menu without saving the changes.

23

EXIT

EXIT

SAVE & EXIT

EXIT

Save the current settings and exit the OSD menu.

Exit the OSD menu without saving the changes.

24

TROUBLESHOOTING

Before sending your camera for repair, check the following or contact our technical specialist.

FOR NO VIDEO

Check the coaxial cable and make sure it is connected securely.

Check the lens’ iris adjustment at the camera’s OSD menu.

Check the power supply and make sure the camera has the proper voltage and current.

FOR OUT-OF-FOCUS VIDEO

Check the clear dome cover and the lens for dirt or fingerprints. Use a soft cloth and gently clean. Check the lens’ manual focal and zoom adjustment. The use of a field test monitor is recommended.

25

W

ARRANTY INFORMATION*

Digital Watchdog (referred to as “the Warrantor”) warrants the Digital Watchdog Camera against defects in materials or workmanship as follows:

LABOR: For the initial five (5) years and one (1) year on IR LED from the original purchase date, if the camera is determined to be defective, the Warrantor will repair or replace the unit with a new or refurbished product at its option at no charge.

PARTS: In addition, the Warrantor will supply replacement parts for the initial five (5) years and one (1) year on IR LED.

To obtain warranty or out of warranty service, please contact a Technical Support

Representative at 1-866-446-3595 Monday through Friday from 8:30AM to 8:00PM

Eastern Standard Time.

A purchase receipt or other proof of the original purchase date is required before warranty service is rendered. This warranty only covers failures due to defects in materials and workmanship which arise during normal use. This warranty does not cover damage which occurs in shipment or failures which are caused by products not supplied by the Warrantor or failures which result from accident, misuse, abuse, neglect, mishandling, misapplication, alteration, modification, faulty installation, set-up adjustments, improper antenna, inadequate signal pickup, maladjustment of consumer controls, improper operation, power line surge, improper voltage supply, lightning damage, rental use of the product or service by anyone other than an authorized repair facility or damage that is attributable to acts of God.

26

L

IMITS & EXCLUSIONS*

There are no express warranties except as listed. The warrantor will not be liable for incidental or consequential damages (including damage to recording media without limitation) resulting from the use of these products or arising out of any breach of the warranty. All express and implied warranties, including the warranties of merchantability and fitness for particular purpose, are limited to the applicable warranty period set forth above.

Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitatons on how long an implied warranty lasts, so the exclusions or limitations listed above may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from state-to-state.

If the problem is not handled to your satisfaction, then write to the following address:

Digital Watchdog, Inc.

ATTN: RMA Department

5436 W. Crenshaw Street

Tampa, FL 33634

Service calls which do not involve defective materials or workmanship as determined by the

Warrantor, in its sole discretion, are not covered. Costs of such service calls are the responsibility of the purchaser.

27

S

PECIFICATIONS*

DWC-D1363D & DWC-D1363D922

VIDEO

Image Sensor

Total Pixels

Effective Pixels

Frequency

Synchronization

Horizontal Resolution

Minimum Illumination

S/N Ratio

Video Output

LENS

Focal Length

Lens Type

OPERATIONAL

Day & Night

3D Digital Noise Reduction

Back Light Compensation

Auto Gain Control

Privacy Zones

Language

1/3" CCD

811 (H) x 508 (V), 411K Pixels

768 (H) x 494 (V)

15.734KHz (H), 59.95Hz (V)

Internal or Line Lock

620 TV Lines [B&W], 600 TV Lines [Color]

F1.2 (30IRE): 0.14 Lux [Color]

F1.2 (30IRE): 0.03 Lux [B&W]

52dB (AGC off)

CVBS: 1.0Vp-p / 75 Ω

3.3-12mm [DWC-D1363D], 9-22mm [DWC-D1363D922]

DC Auto Iris

Electronic

OFF / LOW / MID / HIGH / SMART

OFF / BLC / HME / DRC

OFF / LOW / MID / HIGH / HIGHEST

OFF / ON (8 Programmable Zones)

ENGLISH / JAPANESE / MANDARIN / CANTONESE / GERMAN

RUSSIAN / FRENCH / SPANISH / ITALIAN / DUTCH

28

ENVIRONMENTAL

Operating Temperature

Operating Humidity

Storage Temperature

ELECTRICAL

Power Requirement

Power Consumption

MECHANICAL

Housing Material

Dome Cover Material

Dimensions

Weight

-10 o C ~ 55 o C (14 o F ~ 131 o F)

Less than 90% (Non-Condensing)

-20 o C ~ 70 o C (-4 o F ~ 158 o F)

Dual (12VDC & 24VAC)

12VDC: 1.7, 141.7mA

24VAC: 2.4W, 100mA

Plastic

Polycarbonate

∅ 123.8 x 85 mm ( ∅ 4.9 X 3.35 in)

0.7 lbs

*Specification is subject to change without prior notice.

29

30

M

EMO*

M

EMO*

31

5436 W Crenshaw St. Tampa, FL 33634

Tel : 866-446-3595 / 813-888-9555

Fax : 813-888-9262 www.Digital-Watchdog.com

[email protected]

Technical Support Hours : Monday-Friday

8:30am to 8:00pm EST