User manual | 1 C G S

GETTING STARTED
CHAPTER
1
In This Chapter...
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1–2
Conventions Used . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1–3
Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1–4
Agency Approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1–4
Part Number Key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1–5
Product Label Example: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1–5
Serial Number and Date Code format: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1–5
Quick Start Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1–6
Step 1 – Unpack and Inspect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1–6
Step 2 – Install Optional Hardware Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . .1–7
Step 3 – Become Familiar with Available Communication Ports . . . . . . . . . . . . . . . .1–8
Step 4 – Install C-more 6” Micro-Graphic Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . .1–9
Enclosure Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1–10
Step 5 – Install the Programming Software and Develop a Project . . . . . . . . . . . .1–11
Step 6 – Connect C-more 6” Micro-Graphic Panel to Computer . . . . . . . . . . . . .1–12
Step 7 – Providing Power to the C-more 6” Micro-Graphic Panel . . . . . . . . . . . . .1–13
Step 8 – Accessing the C-more 6” Micro-Graphic Panel Setup Screens . . . . . . . . .1–14
Step 9 – Choose C-more 6” Micro-Graphic Panel to PLC Protocol & Cables . . . . .1–15
Step 10 – Connect C-more 6” Micro-Graphic Panel to PLC . . . . . . . . . . . . . . . . . .1–16
Chapter 1: Getting Started
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
Introduction
1–2
The Purpose of this Manual
Thank you for purchasing from our C-more® Micro-Graphic family of products. This manual
describes AutomationDirect.com’s C-more 6” Micro-Graphic panels, their specifications,
included components and available accessories and provides you with important information
for installation, connectivity and setup. The manual shows you how to install, wire and use the
products. It also helps you understand how to interface the panels to other devices in a control
system.
This user manual contains important information for personnel who will install the panels and
accessories, and for the personnel who will be programming the panel. If you understand
control systems making use of operating interfaces such as the C-more Micro-Graphic panels,
our user manuals will provide all the information you need to get, and keep, your system up and
running.
Supplemental Manuals
If you are familiar with industrial control type devices, you may be able to get up and running
with just the aide of the Quick Start Guide that is included with each panel. You may also refer
to the online help that is available in the C-more Micro-Graphic programming software.
Technical Support
We strive to make our manuals the best in the industry. We rely on your feedback to let us know
if we are reaching our goal. If you cannot find the solution to your particular application, or, if
for any reason you need technical assistance, please call us at:
770–844–4200
Our technical support group will work with you to answer your questions. They are available
Monday through Friday from 9:00 A.M. to 6:00 P.M. Eastern Time. We also encourage you to
visit our web site where you can find technical and non-technical information about our
products and our company.
http://www.automationdirect.com
If you have a comment, question or suggestion about any of our products, services, or manuals,
please fill out and return the ‘Suggestions’ card that was included with this manual.
®
EA1-MG6-USER-M Hardware User Manual, 1st Ed. Rev E, 07/13
Chapter 1: Getting Started
Conventions Used
When you see the “notepad” icon in the left-hand margin, the paragraph to its immediate right will be a
special note. The word NOTE: in boldface will mark the beginning of the text.
When you see the “exclamation mark” icon in the left-hand margin, the paragraph to its immediate
right will be a warning. This information could prevent injury, loss of property, or even death (in
extreme cases). The word WARNING: in boldface will mark the beginning of the text.
Key Topics for Each Chapter
The beginning of each chapter will list the key topics
that can be found in that chapter.
Getting Started
CHAPTER
1
In This Chapter...
General Information .................................................................1-2
Specifications ...........................................................................1-4
®
EA1-MG6-USER-M Hardware User Manual, 1st Ed. Rev E, 07/13
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
1–3
Chapter 1: Getting Started
Product Overview
1
2
3
EA1-S6MLW
EA1-S6ML
4
The C-more 6” Micro-Graphic panel has a 5.7-inch STN LCD monochrome 320 x 240 dot
5
display. Model EA1-S6ML has five selectable LED-driven backlight colors including Green,
Red, Amber, Yellow and Lime. Model EA1-S6MLW has five selectable LED-driven backlight
colors including White, Pink1, Pink2, Pink3 and Red. Both models feature five user-defined
6
function keys, each key with a user-defined red LED indicator. The panels can display up to 40
lines by 78 characters of static text and up to 40 lines by 40 characters of dynamic text with
7
embedded variables and phrases mixed with graphics at landscape orientation. Portrait
orientation can display 59 characters and 40 lines of static text and 40 lines by 40 characters of
dynamic text. Each model is rated NEMA 4/4X, IP-65 (when mounted correctly, for indoor use
8
only). The C-more 6” Micro-Graphic panels are powered from a 12-24 VDC class 2 power
supply or can operate in low-power mode when powered from the serial communications port
9
of select AutomationDirect PLCs.
Other features include:
10
• 1792 KB memory
• Built in RJ12 serial communications port (RS-232)
11
• Built in 15-pin serial communications port (RS-232/422/485)
• Adjustable contrast
12
• 2 optional keypad bezels, 20-button landscape and 21-button portrait mount
• Optional replaceable clear screen overlay
• Built in Alarm Control setup that activates beep, backlight flash, customized alarm banner, and red
13
LED blinking
• Up to 999 screens, limited only by memory usage
14
• 0 to 50 °C (32 to 122 °F) operating temperature range
• UL, cUL, CSA & CE agency approvals (see below for details)
A
• 2-year warranty from date of purchase
B Agency Approvals
UL/CUL/CSA/CE Certification Numbers
Name
UL/CUL
UL508
CSA
CE
ISO-9000
C
D
shown in Landscape (Horizontal) mode
C-more Micro-Graphic Panels
& Accessories
C
1–4
®
UL
E157382
R
E157382
shown in Portrait (Vertical) mode
234884
EN61131-2
Yes
US
EA1-MG6-USER-M Hardware User Manual, 1st Ed. Rev E, 07/13
Chapter 1: Getting Started
Part Number Key
Panel Part Number Key
The C-more 6” Micro-Graphic panel part numbers consist of the following:
Display Size:
6: 5.7”
Series Name:
EA1: C-more Micro-Graphic
Display Color:
M: Monochrome
Backlight Type:
L: LED
EA1-S6MLx
Display Type:
S: STN
Features:
blank: Green / Red backlight
W:
White / Red backlight
Bezel Part Number Key
The optional C-more 6” Micro-Graphic keypad bezel part numbers consist of the following:
Series Name:
EA-MG6: C-more 6” Micro-Graphic
Bezel Option Module
EA-MG6-XXXX
Module Type:
BZ2: 20-Key Bezel for landscape mode
BZ2P: 21-Key Bezel for portrait mode
Product Label Example:
EA1-S6ML
EA1-S6MLW
R05. 1 2 3 4 5
MODEL : EA1-S6MLW
INPUT:12-24V 6.5W Class2
Type 4X Indoor Use Only
Ro
Date code:****
MADE IN CHINA
R
LISTED
7M17
IND.CONT.EQ.
LR234884
EA1-S6MLW + serial number
Serial Number and Date Code format:
Serial Number =
YY:
M:
DD:
F:
NNN:
Date Code =
Y:
MM:
F:
®
[Part Number]+[YYMDDFNNN]
Year (07–99 --- e.g. 07 = 2007)
Month (1–9, X, Y, Z --- e.g. X = Oct.)
Day (1–31)
Manufacturing Site (0–9, A–Z)
Sequence number for the date listed (000–999)
YMMF
Year (0–9 --- e.g. 07 = 2007)
Month (01–12 --- e.g. X = Oct.)
Manufacturing Site (0–9, A–Z)
EA1-MG6-USER-M Hardware User Manual, 1st Ed. Rev E, 07/13
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
1–5
Chapter 1: Getting Started
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
Quick Start Steps
1–6
Step 1 – Unpack and Inspect
a.) Unpack the C-more 6” Micro-Graphic panel from its shipping carton. Included in the
carton are the following:
• C-more 6” Micro-Graphic panel (EA1-S6ML or EA1-S6MLW)
• DC power connector (EA-MG-DC-CON)
• cutout template
• mounting clips
• gasket
• function key label inserts
• Quick Start Guide
b.) Unpack any accessories that have
been ordered, such as:
Keypad Bezel, programming
cable, PLC communications
cable, etc.
c.) Inspect all equipment for
completeness. If anything is
missing or damaged,
immediately call the
AutomationDirect® returns
department @ 1-800-633-0405.
Mounting
Clips
Function Key
Label Inserts
DC Power
Connector
Cutout
Template
C-more 6 Inch
Micro-Graphic
Panel
Shipping Carton Contents
Optional Accessories
20-Button Horizontal Keypad Bezel
EA-MG6-BZ2
®
21-Button Vertical Keypad Bezel
EA-MG6-BZ2P
EA1-MG6-USER-M Hardware User Manual, 1st Ed. Rev E, 07/13
Chapter 1: Getting Started
Step 2 – Install Optional Hardware Accessories
Below is an example of a C-more 6” Micro-Graphic panel being assembled with an optional
EA-MG6-BZ2 20-button Keypad Bezel.
2. Use the (4) Panel Mounting
Clips, EA-MG-BZ2-BRK,
that are supplied with the
panel, to secure panel to
keypad bezel and compress
the gasket between the
panel and the keypad bezel.
Tighten screws to a torque
of 21-28 oz-in [0.15-0.2 Nm].
3. Use (8) Bezel Mounting Clips,
EA-MG-BZ2-BRK, to secure keypad
bezel through enclosure cutout.
Tighten screws to a torque of
21-28 oz-in [0.15-0.2 Nm].
Function
Key Label
Insert
1. Remove
Expansion
Connector
Protective
Cover from
rear of
panel.
20 Button
Keypad Bezel
EA-MG6-BZ2
C-more 6 Inch
Micro-Graphic Panel
4. Peel Protective Film
from front of panel.
NOTE: Mounting clips for the panel and keypad bezels are included with the respective product.
Optional Accessory
Clear Screen Overlay
EA-6-COV2
®
EA1-MG6-USER-M Hardware User Manual, 1st Ed. Rev E, 07/13
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
1–7
Chapter 1: Getting Started
Step 3 – Become Familiar with Available Communication Ports
1–8
The C-more 6” Micro-Graphic panel includes a built-in RS-232 serial communications port
designated as Port1. This port uses an RJ12 type telephone jack to make connections to either
the EA-MG-PGM-CBL programming cable assembly or a communications cable, such as an
EA-2CBL, to interface with a PLC or controller. The panel can receive power through this port
from the serial communications port on AutomationDirect CLICK™ and select
Direct LOGIC PLCs. The other serial communications port designated as Port2 is a 15-pin Dsub connector that supports RS-232, RS-485 and RS-422.
NOTE: When the 6” panel is powered through Port1 from a connected PLC or PC, the screen brightness is
diminished because the panel is running in Low-Power Mode. For full brightness, connect an external
12-24 VDC power source to the panel’s power connection. Low-Power Mode is intended for initial
programming. For full brightness, connect an external 12-24 VDC power source when the panel is installed
in its application.
RJ12 serial
communications Port1
Expansion
Connector
R01. 1 2 3 4 5
MODEL:EA1-S6MLW
R
INPUT:12-24V 6.5W
Date code:****
MADE IN CHINA
LISTED 4
2
7M17
IND.CONT.EQ.
EA1-S6MLW + serial number
8
1
15
9
PLC 15-pin serial
communications Port2
Pin
6 5 4 3 2 1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
Signal
1
Logic GND
2
not used
3
RXD (232C)
4
TXD (232C)
5
+5 VDC
6
Logic GND
Pin
Signal
Pin
1
Frame GND
6
LE
11
2
TXD (232C)
7
CTS (232C)
12 TXD– (422/485)
3
RXD (232C)
8
RTS (232C)
13 Term. Resistor
4
do not use
9
RXD+ (422/485)
14 do not use
5
Logic GND
10 RXD– (422/485)
15 do not use
RS-232
Signal
Pin
Signal
TXD+ (422/485)
RS-232/422/485
NOTE: See Chapter 2: Specifications and Chapter 6: PLC Communications for additional details on the
available communication ports, protocols and cables.
NOTE: The panel has a built-in RJ12 serial communications port (Port1 - RS-232) and a built in 15-pin serial
communications port (Port2 - RS-232/422/485). Only one of the ports can be used with a connected PLC.
The programming software allows the user to select either Port1 or Port2 under the Panel Manager dialog
box. When using Port2 to communicate with the connected PLC, Port1 can still be used with the EA-MGPGM-CBL Software Programming Cable Assembly to transfer projects between the PC and panel.
®
EA1-MG6-USER-M Hardware User Manual, 1st Ed. Rev E, 07/13
3
Chapter 1: Getting Started
Step 4 – Install C-more 6” Micro-Graphic Panel
The C-more 6” Micro-Graphic panel can be mounted through a cutout in an enclosure by using
the template that is provided with the panel, or using the dimensions shown below. Cutout
dimensions for the 20-button landscape and 21-button portrait keypad bezel options are also
shown below. The keypad bezels also include a template that can be used. The enclosure
mounting thickness range for the panels and the keypad bezels is 0.04”–0.2” [1–5 mm].
The screw torque range for the screws used on the panel mounting clips and the keypad bezel
mounting clips is 21-28 oz-in [0.15-0.2 Nm].
See Chapter 2: Specifications for additional product dimensions.
Chapter 3: Accessories for accessory specifications and dimensions.
EA1-S6ML & EA1-S6MLW
Panel Cutout
0.260
[6.6]
0.256
[6.5]
+0.04
6.339 –0.00
+1
161.0 –0
0.260
[6.6]
+0.04
4.811 –0.00
0.260
[6.6]
+1
122.2 –0
R .118 [R3]
0.256
[6.5]
CUTOUT
OUTLINE
BEZEL
OUTLINE
0.256
[6.5]
+0.04
6.339 –0.00
+1
161.0 –0
R .118 [R3]
CUTOUT
OUTLINE
+0.04
4.811 –0.00
+1
122.2 –0
BEZEL
OUTLINE
Portrait Mode (Vertical)
CUTOUT
0.260
[6.6]
0.256
[6.5]
CUTOUT
BEZEL
OUTLINE
Landscape Mode (Horizontal)
CUTOUT
OUTLINE
0.382
[9.7]
CUTOUT
+0.04
9.236 –0.00
234.6
0.382
[9.7]
0.382
[9.7]
+1
–0
0.382
[9.7]
+0.04
BEZEL
OUTLINE
R0.59 [R1.5]
CUTOUT
+0.04
9.236 –0.00
+1
234.6 –0
CUTOUT
OUTLINE
5.630 –0.00
+1
143.0 –0
0.382
[9.7]
0.382
[9.7]
EA-MG6-BZ2
Landscape (Horizontal)
Keypad Bezel Cutout
®
+0.04
EA-MG6-BZ2P
Portrait (Vertical)
Keypad Bezel Cutout
0.382
[9.7]
Units: Inches [mm]
R0.59 [R1.5]
5.630 –0.00
+1
143.0 –0
EA1-MG6-USER-M Hardware User Manual, 1st Ed. Rev E, 07/13
0.382
[9.7]
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
1–9
Chapter 1: Getting Started
Enclosure Clearances
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
1–10
A 1.2” [30mm] minimum clearance is required inside an enclosure for proper ventilation of
the C-more Micro-Graphic panel.
1.2
[30.0]
EA1-S6ML(W)
Rear View
1.2
[30.0]
1.2
[30.0]
R01. 1 2 33 4 5
MODEL:EA1-S6MLW
R
INPUT:12-24V 6.5W
Date code:****
MADE IN CHINA
LISTED
7M17
IND.CONT.EQ.
EA1-S6MLW + serial number
8
1
15
9
1.2
[30.0]
Enclosure
units: inches [mm]
Panel with Keypad
Bezel
Panel only
Enclosure
Enclosure
1.2
[30.0]
1.2
[30.0]
EA1-S6ML(W) with
EA-MG6-BZ2(P)
4
EA1-S6ML(W)
NOTE: Additional clearance inside the enclosure is required when connecting to the 15-pin serial
communications port (Port2).
®
EA1-MG6-USER-M Hardware User Manual, 1st Ed. Rev E, 07/13
Chapter 1: Getting Started
Step 5 – Install the Programming Software and Develop a Project
Following are the minimum system requirements for running C-more Micro-Graphic
Programming Software, EA-MG-PGMSW, on a PC:
• Operating System - Windows® XP Home / Professional Edition Service Pack 2, Windows® 2000
with Service Pack 4, Windows® Vista (32 and 64 bit), Windows® 7 (32 and 64 bit), Windows 8
(32 and 64 bit)
• Keyboard and Mouse or compatible pointing device
• Super VGA color video adapter and monitor with at least 800 x 600 pixels resolution
(1024 x 768 pixels recommended) 64K color minimum
• 150 MB free hard-disk space
• 128 MB free RAM (512 MB recommended); 512 MB free RAM (1GB recommended) for Vista
• CD-ROM or DVD drive for installing software from the CD, or internet access to download free
programming software
• USB port to use with an EA-MG-PGM-CBL, USB to RS232 Programming Cable Assembly
for project transfer from the programming software to the panel
Insert the supplied CD-ROM into the PC’s CD-ROM drive and follow the instructions. If you
need assistance during the software installation, please refer to the supplied Software Installation
Guide or call the AutomationDirect Technical Support team at 770-844-4200.
Start
Simulate
a Project
Send
Project
Project to panel
Download your project to the
connected panel.
Allows you to check the operation of
your project before downloading it to
the panel.
Make a New Project
Select Project
Location:
C:\My Documents\C-more Projects\ Browse...
Project:
MyProject
HMI Type:
EA1-S6ML
Enter a name
for your project
Select the C-more
Micro-Graphic panel
PLC Protocol: DirectLogic K-Sequence
Select the PLC Driver
Protocol Setup...
®
EA1-MG6-USER-M Hardware User Manual, 1st Ed. Rev E, 07/13
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
1–11
Chapter 1: Getting Started
Step 6 – Connect C-more 6” Micro-Graphic Panel to Computer
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
1–12
NOTE: Install C-more Micro-Graphic Programming software before connecting the panel to the PC to ensure
the panel drivers install correctly.
Use an EA-MG-PGM-CBL, USB to RS-232 Programming Cable Assembly, from an USB
port type A on the project development PC, through the supplied converter, to the RJ12
RS-232 programming/PLC serial communications port on the C-more Micro-Graphic panel as
shown below.
USB to RS-232 Programming Cable Assembly
PC to Panel Programming
Cable Assembly
(Includes serial & USB cables)
EA-MG-PGM-CBL
USB
Cable
Serial
Cable
USB to RS232
Converter
User PC
C-more 6 inch
Micro Graphic
Panel
NOTE: When the panel is powered through Port1 from a connected PLC or PC, the screen brightness is
diminished because the panel is running in Low-Power Mode. For full brightness, connect an external
12-24 VDC power source to the panel’s power connection. Low-Power Mode is intended for initial
programming. For full brightness, connect an external 12-24 VDC power source when the panel is installed
in its application.
®
EA1-MG6-USER-M Hardware User Manual, 1st Ed. Rev E, 07/13
Chapter 1: Getting Started
Step 7 – Providing Power to the C-more 6” Micro-Graphic Panel
Power can be supplied to the C-more Micro-Graphic panel in one of two different ways.
1.) During operation, the panel functions in High-Power Mode when powered by a minimum 1 Amp
12 - 24 VDC class 2 power source. Recommended power supplies are AutomationDirect part
number PSC-24-015 or PSC-24-030.
2.) The C-more Micro-Graphic panel is powered during programming from the PC through the USB
to RS-232 Programming Cable Assembly, EA-MG-PGM-CBL. The panel will operate in Lowpower mode when powered by the PC and result in a dim screen.
3.) Optionally, the C-more Micro-Graphic panel can function in Low-Power Mode powered from most
AutomationDirect PLC’s RJ12 serial communications port. Use a DV-1000CBL communications
cable, or a DV-1000CBL communications cable with a FA-15HD 15-pin HD DSub/RJ12 Adapter
connected to most AutomationDirect PLC’s 15-pin HD communications port (DL06, D2-250-1
& D2-260) PLCs for Low-Power operation. See Chapter 6: PLC Communications for additional
details. The panel will operate in low-power mode when powered by the PC.
To PLC
RJ12 Port
*Panel Powered from
AutomationDirect PLC via
Communications Cable
Power Supplied to Panel through Cable from AutomationDirect PLC RJ12 port:
RS-232C (p/n DV-1000CBL)
To C-more
Micro-Graphic
Serial Port1
10 feet [3.0 m] Maximum
Wiring Diagram
1 = Sig GND
2 = +5 VDC
3 = RXD
4 = TXD
5 = not used
6 = Sig GND
RJ12 6-pin
Phone Plug
(6P6C)
GND
6
1
GND
TXD
4
3
RXD
RXD
3
4
TXD
+5 V
2
5
+5 V
GND
1
6
GND
123456
RJ12 6-pin
Phone Plug
(6P6C)
1 = Sig GND
2 = not used
3 = RXD
4 = TXD
5 = +5 VDC
6 = Sig GND
123456
NOTE: When the 6” panel is powered through Port1 from a connected PLC or PC, the screen brightness is
diminished because the panel is running in Low-Power Mode. For full brightness, connect an external
12-24 VDC power source to the panel’s power connection. Low-Power Mode is intended for initial
programming. For full brightness, connect an external 12-24 VDC class 2 power source when the panel is
installed in its application.
Panel Powered from a DC Power Source - Wiring Diagram
R01. 1 2 3 4 5
MODEL:EA1-S6MLW
R
INPUT:12-24V 6.5W
Date code:****
MADE IN CHINA
LISTED
7M17
IND.CONT.EQ.
EA1-S6MLW + serial number
Recommended
DC Supply Fuse
750 mA fast acting,
ADC p/n AGC-75
GND
Equipment
Ground
8
1
15
9
Supply to Panel:
1 A @ 12 - 24 VDC
(10.8 - 26.4 VDC)
–
+
NOTE: Recommended DC power supply to power the C-more Micro-Graphic Panel, AutomationDirect Part
No. PSC-24-015 or PSC-24-030.
®
EA1-MG6-USER-M Hardware User Manual, 1st Ed. Rev E, 07/13
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
1–13
Chapter 1: Getting Started
Step 8 – Accessing the C-more 6” Micro-Graphic Panel Setup Screens
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
1–14
To access the Setup Menu of the panel’s setup screens, press the the BAK [F1] and ENT [F5]
function keys simultaneously for three (3) seconds.
From the Setup Menu, information about the panel can be obtained, settings can be adjusted,
and panel functions can be tested.
NOTE: See Chapter 5: System Setup Screens for details on using the setup screen settings and functions.
Menu Flow Chart
Setup Menu
[pg. 5-5]
1. Information
[pg. 5-6]
1. Memory
[pg. 5-6]
2. Protocol
[pg. 5-6]
3. Extensions
[pg. 5-6]
BAK
4. Versions
[pg. 5-6]
SETUP MENU
1. Information
2. Setting
3. Test Menu
4. Exit
>
>
>
>
2. Setting
[pg. 5-7]
UP
1. LCD Contrast
[pg. 5-7]
2. Backlight
[pg. 5-8]
DWN
ENT
3. Beep
[pg. 5-10]
ENT
4. Calibration
[pg. 5-11]
5. Clear User Memory
[pg. 5-12]
6. Reset to Factory Default
[pg. 5-12]
7. Hourglass
[pg. 5-13]
BAK
8. Rotation
[pg. 5-14]
MEMORY
Total:
1835008 Bytes
Usage:
3. Test Menu
[pg. 5-15]
1. Serial Port1 – Loop Back Test
[pg. 5-15]
26206 Bytes
Free:
2. Serial Port2 – Loop Back Test
[pg. 5-16]
1808802 Bytes
3. PLC Enquiry Test
[pg. 5-17]
4. Buzzer Test
[pg. 5-17]
5. Touch Panel Test
[pg. 5-18]
4. Exit
[pg. 5-18]
®
Do you want to exit from System Screen?
No[F1] / Yes[F5]
EA1-MG6-USER-M Hardware User Manual, 1st Ed. Rev E, 07/13
Chapter 1: Getting Started
Step 9 – Choose C-more 6” Micro-Graphic Panel to PLC Protocol & Cables
Available PLC Protocols
PLC Drivers
Serial - port1 or port2
Serial - port2 only
AutomationDirect Productivity Series
Allen-Bradley DF1 Half Duplex
AutomationDirect Do-more
Allen-Bradley DF1 Full Duplex
AutomationDirect CLICK
Allen-Bradley PLC5 DF1
AutomationDirect K-sequence
Allen-Bradley DH485
AutomationDirect DirectNET
GE SNPX (90/30, 90/70, Micro 90, VersaMax Micro)
AutomationDirect Modbus
Mitsubishi FX
Modicon Modbus RTU
Mitsubishi Q & QnA
Entivity Modbus RTU
Omron Host Link (C200 Adapter, C500)
Omron FINS Serial (CJ1, CS1)
Siemens PPI (S7-200 CPU)
AutomationDirect SOLO Temperature Controller
AutomationDirect GS Drives
Available purchased cables
Cable Description
Cable Description
Cable Part No.
Cables used with serial Port1
AutomationDirect Productivity Series,
Do-more, CLICK, Direct LOGIC PLC RJ-12
port, DL05, DL06, DL105, DL205, D3-350,
D4-450 & H2-WinPLC (RS-232C)
DV-1000CBL
Note: The PLC can provide 5 VDC through this cable. No
external 12-24 VDC souce is required, however,
screen brightness is diminished and the alarm beep
will not function.
Direct LOGIC DL405 PLC 15-pin D-sub
port, DL405
(RS-232C)
D4-1000CBL
Direct LOGIC (VGA Style) 15-pin port,
DL06, D2-250 (250-1), D2-260
(RS-232C)
Use with DV-1000CBL cable.
FA-15HD
Direct LOGIC PLC 15-pin D-sub port,
DL405
(RS-232C).
Direct LOGIC PLC RJ-11 port, D3-340
(RS-232C).
FA-CABKIT
OP-3CBL-1
Cable Part No.
Cables used with serial Port2
AutomationDirect Productivity Series,
Do-more, CLICK, DirectLOGIC PLC RJ-12
port, DL05, DL06, DL105, DL205, D3-350,
D4-450 & H2-WinPLC (RS-232C)
Direct LOGIC (VGA Style) 15-pin port,
DL06, D2-250 (250-1), D2-260
(RS-232C).
Direct LOGIC PLC RJ-11 port, D3-340
(RS-232C).
Direct LOGIC DL405 PLC 15-pin D-sub
port, DL405 (RS-232C).
Direct LOGIC PLC 25-pin D-sub port,
DL405, D3-350, DL305 DCU and all DCM’s
(RS-232C).
Allen-Bradley MicroLogix 1000, 1100,
1200, 1400 & 1500 (RS-232C)
Allen-Bradley SLC 5-03/04/05,
ControlLogix, CompactLogix, FlexLogix
DF1 port (RS-232C)
Allen-Bradley PLC-5 DF1 port
(RS-232C)
Allen-Bradley MicroLogix, SLC 5-01/02/03,
PLC5 DH485 port (RS-232C)
GE 90/30, 90/70, Micro 90, Versamax
Micro (Port2) 15-pin D-sub port
(RS-422A)
MITSUBISHI FX Series 25-pin port
(RS-422A)
MITSUBISHI FX Series 8-pin mini-DIN
(RS-422A)
OMRON Host Link (C200 Adapter, C500)
(RS-232C)
EA-2CBL
EA-2CBL-1
EA-3CBL
EA-4CBL-1
EA-4CBL-2
EA-MLOGIX-CBL
EA-SLC-232-CBL
EA-PLC5-232-CBL
EA-DH485-CBL
EA-90-30-CBL
EA-MITSU-CBL
EA-MITSU-CBL-1
EA-OMRON-CBL
NOTE: See Chapter 6: PLC Communications for a detailed chart of PLC compatibility & cable connections.
Chapter 6 includes wiring diagrams for end user construction of certain cables.
®
EA1-MG6-USER-M Hardware User Manual, 1st Ed. Rev E, 07/13
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
1–15
Chapter 1: Getting Started
Step 10 – Connect C-more 6” Micro-Graphic Panel to PLC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
A
B
C
D
Connect the serial communications cable between the C-more Micro-Graphic panel and the
PLC. The panel can be connected to the PLC via the panel’s built-in RJ12 serial
communications port (RS-232) or 15-pin serial communications port with either RS-232, RS422 or RS-485 communications.
Example of panel’s Port 1
connected to a CLICK PLC
C-more 6 Inch
Micro-Graphic
Panel
CLICK PLC
Port 1
DV-1000CBL
serial cable
Port 2
C-more 6 Inch
Micro-Graphic
Panel
Recommended
DC Supply Fuse
750 mA fast acting,
ADC p/n AGC-75
DL-06 PLC
Port
2
Port
2
Example of panel’s Port 2
connected to a DL06 PLC
1–16
®
PSC-24-015
Power Supply
EA-2CBL-1
serial cable
EA1-MG6-USER-M Hardware User Manual, 1st Ed. Rev E, 07/13

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project