6719DD 6727DD OWNER’S MANUAL

6719DD 6727DD OWNER’S MANUAL
TD851/951(P01-35).QX33
03.3.1 1:53 PM
Page 1
OWNER’S
MANUAL
COLOR TV/DVD/VCR TRIPLE COMBO
6719DD
6727DD
(19 inch)
(27 inch)
27” MODEL ILLUSTRATED
SUPPLIED ACCESSORIES
This Owner’s Manual is
made of recycled paper.
ACCESSORIES
Remote Control Unit NE209UD
INSTRUCCIONES EN ESPAÑOL INCLUIDAS.
As an ENERGY STAR ®
Partner, our company has
determined that this product meets
the ENERGY STAR ® guidelines for
energy efficiency. ENERGY STAR ® is
a U.S. registered mark.
PART NO.
Batteries
2 AA Batteries
Owner’s Manual
0EMN02116
If you need additional operating assistance after reading this owner’s
manual or to order replacement accessories, please call
TOLL FREE : 1-800-968-3429.
Or visit our WEB SITE at http://www.funai-corp.com
Please read before using this equipment
TD851/951(P01-35).QX33
03.3.1 1:53 PM
Page 2
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A
RISK OF ELECTRIC SHOCK IS PRESENT
WITHIN THIS UNIT.
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
THIS SYMBOL INDICATES THAT THERE
ARE IMPORTANT OPERATING AND
MAINTENANCE INSTRUCTIONS IN THE
LITERATURE ACCOMPANYING THE
APPLIANCE.
CAUTION
The caution marking is located on the rear of the cabinet.
IMPORTANT SAFEGUARDS
1.Read instructions-All the safety and operating instructions
should be read before the appliance is operated.
AMEUBLES- Cet appareil ne doit SYMBOLE D'AVERTISSEMENT POUR
être placé que sur un meuble (avec APPAREILLESETCOMPOSANTES
MEUBLE A ROULETTES
ou sans roulettes) recommandé par
le fabricant. Si vous l’installez sur
un meuble à roulettes, déplacez les
deux ensembles avec précaution.
Un arrêt brusque, l’utilisation
d’une force excessive et des surS3126A
faces irrégulières risquent de déstabiliser l’ensemble et de le renverser.
2.Retain Instructions-The safety and operating instructions
should be retained for future reference.
3.Heed Warnings-All warnings on the appliance and in the
operating instructions should be adhered to.
4.Follow Instructions-All operating and use instructions
should be followed.
5.Cleaning-Unplug TV/DVD/VCR from the wall outlet before
cleaning. Do not use liquid cleaners or aerosol cleaners. Use
a damp cloth for cleaning.
EXCEPTION: A product that is meant for uninterrupted
service and, that for some specific reason, such as the possibility of the loss of an authorization code for a CATV converter, is not intended to be unplugged by the user for cleaning or any other purpose, may exclude the reference to
unplugging the appliance in the cleaning description otherwise required in item 5.
6.Attachments-Do not use attachments not recommended by
the TV/DVD/VCR manufacturer as they may cause hazards.
7.Water and Moisture-Do not use this TV/DVD/VCR near
water-for example, near a bath tub, wash bowl, kitchen sink,
or laundry tub, in a wet basement, or near a swimming pool,
and the like.
8.Accessories-Do not place this TV/DVD/VCR on an unstable
cart, stand, tripod, bracket, or table. The TV/DVD/VCR may
fall, causing serious injury to someone, and serious damage
to the appliance. Use only with a cart, stand, tripod, bracket,
or table recommended by the manufacturer, or sold with the
TV/DVD/VCR. Any mounting of
PORTABLE CART WARNING
the appliance should follow the
manufacturer’s instructions and
should use a mounting accessory
recommended by the manufacturer.
An appliance and cart combination
should be moved with care.Quick
stops, excessive force, and uneven
S3126A
surfaces may cause the appliance
and cart combination to overturn.
9. Ventilation-Slots and openings in the cabinet and the back
or bottom are provided for ventilation and to ensure reliable
operation of the TV/DVD/VCR and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the
TV/DVD/VCR on a bed, sofa, rug, or other similar surface.
This TV/DVD/VCR should never be placed near or over a
radiator or heat register. This TV/DVD/VCR should not be
placed in a built-in installation such as a bookcase or rack
unless proper ventilation is provided or the manufacturer’s
instructions have been adhered to.
10.Power Sources-This TV/DVD/VCR should be operated
only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to
your home, consult your appliance dealer or local power
company. For TV/DVD/VCRs intended to operate from
battery power, or other sources, refer to the operating
instructions.
11.Grounding or Polarization-This TV/DVD/VCR is
equipped with a polarized alternating-current line plug(a
plug having one blade wider than the other). This plug will
fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit,
contact your electrician to replace your obsolete outlet. Do
not defeat the safety purpose of the polarized plug.
12.Power-Cord Protection-Power-supply cords should be
routed so that they are not likely to be walked on or
pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles,
and the point where they exit from the appliance.
-2-
EN
1B15
TD851/951(P01-35).QX33
03.3.1 1:53 PM
Page 3
F IGURE A
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECT RICAL CODE
ANTE NNA
L EAD I N
WI RE
GROUND
CLAMP
A NTENNA
DI SCHARG E UN I T
(NEC SECTION 8 10 -2 0)
EL ECT RI C
SE RV I CE
EQ U I PM EN T
G RO UNDI NG CO NDUCT ORS
(NEC SECTION 8 10 -2 1)
G RO UND CL AM PS
NEC - NATI O NAL EL ECTRI CAL CO DE
POWER SERVI C E G RO UNDI NG
EL EC TR O DE SYST EM
(NEC ART 2 50 , PART H)
S2 8 9 8 A
13.Outdoor Antenna grounding-If an outside antenna or
cable system is connected to the TV/DVD/VCR, be sure
the antenna or cable system is grounded so as to provide
some protection against voltage surges and built-up static
charges. Article 810 of the National Electrical Code,
ANSI/NFPA No. 70, provides information with respect to
proper grounding of the mast and supporting structure,
grounding of the lead-in wire to an antenna discharge unit,
size of grounding conductors, location of antenna-discharge
unit, connection to grounding electrodes, and requirements
for the grounding electrode. (Fig. A)
14.Lightning-For added protection for this TV/DVD/VCR
receiver during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from
the wall outlet and disconnect the antenna or cable system.
This will prevent damage to the TV/DVD/VCR due to
lightning and power-line surges.
19.Damage Requiring Service-Unplug this TV/DVD/VCR
from the wall outlet and refer servicing to qualified service
personnel under the following conditions:
a. When the power-supply cord or plug is damaged or frayed.
b. If liquid has been spilled, or objects have fallen into the
TV/DVD/VCR.
c. If the TV/DVD/VCR has been exposed to rain or water.
d. If the TV/DVD/VCR does not operate normally by following the operating instructions. Adjust only those controls
that are covered by the operating instructions, as improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to
restore the TV/DVD/VCR to its normal operation.
e. If the TV/DVD/VCR has been dropped or damaged in any
way.
15.Power Lines-An outside antenna system should not be
located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into
such power lines or circuits. When installing an outside
antenna system, extreme care should be taken to keep from
touching such power lines or circuits as contact with them
might be fatal.
16.Overloading-Do not overload wall outlets and extension
cords as this can result in a risk of fire or electric shock.
17.Object and Liquid Entry-Never push objects of any kind
into this TV/DVD/VCR through openings as they may
touch dangerous voltage points or short out parts that could
result in a fire or electric shock. Never spill liquid of any
kind on the TV/DVD/VCR.
f. When the TV/DVD/VCR exhibits a distinct change in performance-this indicates a need for service.
20.Replacement Parts-When replacement parts are required,
be sure the service technician has used replacement parts
specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may
result in fire, electric shock, injury to persons or other hazards.
21.Safety Check-Upon completion of any service or repairs to
this TV/DVD/VCR, ask the service technician to perform
routine safety checks to determine that the TV/DVD/VCR
is in proper operating condition.
22.Heat-This TV/DVD/VCR product should be situated away
from heat sources such as radiators, heat registers, stoves,
or other products (including amplifiers) that produce heat.
18.Servicing-Do not attempt to service this TV/DVD/VCR
yourself as opening or removing covers may expose you to
dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY
INSERT.
ATTENTION: POUR ÉVITER LES CHOC ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE
LA FICHE DANS LA BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.
-3-
EN
1B15
TD851/951(P01-35).QX33
03.3.1 1:53 PM
Page 4
PRECAUTIONS
LASER SAFETY
This unit employs a laser. Only a qualified service
person should remove the cover or attempt to service this device, due to possible eye injury.
IMPORTANT COPYRIGHT INFORMATION
Unauthorized copying, broadcasting, public performance and lending of discs are prohibited.
FCC WARNING- This equipment may generate or use radio frequency energy. Changes or
modifications to this equipment may cause
harmful interference unless the modifications
are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change
or modification is made.
CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED
HEREIN MAY RESULT IN HAZARDOUS
RADIATION EXPOSURE.
CAUTION: VISIBLE AND INVISIBLE LASER
RADIATION WHEN OPEN AND INTERLOCK
DEFEATED. DO NOT STARE INTO BEAM.
LOCATION: INSIDE, NEAR THE DECK
MECHANISM.
RADIO-TV INTERFERENCE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and
used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation. If this
equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
1) Reorient or relocate the receiving antenna.
2) Increase the separation between the equipment
and receiver.
3) Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
4) Consult the dealer or an experienced radio/TV
technician for help.
This Class B digital apparatus complies with
Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
CAUTION: TO PREVENT ELECTRIC SHOCK,
MATCH WIDE BLADE OF PLUG TO WIDE
SLOT, FULLY INSERT.
ATTENTION: POUR ÉVITER LES CHOC
ÉLECTRIQUES, INTRODUIRE LA LAME LA
PLUS LARGE DE LA FICHE DANS LA
BORNE CORRESPONDANTE DE LA PRISE
ET POUSSER JUSQU’AU FOND.
-4-
EN
1B15
TD851/951(P01-35).QX33
03.3.1 1:53 PM
Page 5
LOCATION
WARNING
For safe operation and satisfactory performance of
your TV/DVD/VCR, keep the following in mind
when selecting a place for its installation:
• Shield it from direct sunlight and keep it away from
sources of intense heat.
• Avoid dusty or humid places.
• Avoid places with insufficient ventilation for proper
heat dissipation. Do not block the ventilation holes at
the top and bottom of the unit. Do not place the unit
on a carpet because this will block the ventilation
holes.
• Install unit in a horizontal position.
• Avoid locations subject to strong vibration.
• Do not place the TV/DVD/VCR near strong magnetic
fields.
• Avoid moving TV/DVD/VCR to locations where
temperature differences are extreme.
Moisture condensation may occur inside the unit
when it is moved from a cold place to a warm place,
or after heating a cold room or under conditions of
high humidity. If a DVD is played in a TV/DVD/
VCR which has moisture, it may damage the DVD
and TV/DVD/VCR. Therefore when the condensation
occurs inside the unit, turn the POWER on and allow
at least 2 hours for the unit to dry out.
SYMBOLS USED IN THIS MANUAL
The following symbols below appear in some headings and notes in this manual, with the following
meanings
TV/VCR
: Description refers to TV/VCR operation (in the
TV/VCR mode).
DVD-V
: Description refers to playback of DVD video discs
(in the DVD mode).
AVOID THE HAZARDS OF
ELECTRICAL SHOCK AND FIRE
• Do not handle the power cord with wet hands.
• Do not pull on the power cord when disconnecting
•
•
•
CD
: Description refers to playback of audio CDs
(in the DVD mode).
it from an AC wall outlet. Grasp it by the plug.
If, by accident, water is spilled on your unit, unplug
the power cord immediately and take the unit to our
Authorized Service Center for servicing.
Do not put your fingers or objects into the
TV/DVD/VCR disc loading tray.
Do not place anything directly on top of the unit.
MP3
: Description refers to playback of MP3 discs
(in the DVD mode).
QUICK
: Description refers to the items to be set by the
QUICK mode (in the DVD mode).
A NOTE ABOUT RECYCLING
This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in
accordance with your local recycling regulations.
Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations concerning chemical wastes.
The serial number of this product may be found on the back of the unit. No other TV/DVD/VCR has the same
serial number as yours. You should record the number and other vital information here and retain this book as
a permanent record of your purchase to aid identification in case of theft. Serial numbers are not kept on file.
Date of Purchase
Dealer Purchase from
Dealer Address
Dealer Phone No.
Model No.
Serial No.
-5-
EN
1C29
TD851/951(P01-35).QX33
03.3.1 1:53 PM
Page 6
TABLE OF CONTENTS
C IMPORTANT SAFEGUARDS . . .2, 3
C PRECAUTIONS . . . . . . . . . . . . . . . .4
LOCATION . . . . . . . . . . . . . . . . . . .5
AVOID THE HAZARDS OF
ELECTRICAL SHOCK AND FIRE .5
WARNING . . . . . . . . . . . . . . . . . . . .5
SYMBOLS USED IN THIS
MANUAL . . . . . . . . . . . . . . . . . . . . .5
C TABLE OF CONTENTS . . . . . . . . . .6
C FEATURES . . . . . . . . . . . . . . . . . . . .7
C OPERATING CONTROLS AND
FUNCTIONS . . . . . . . . . . . . . . . .9, 10
C PREPARATION FOR USE . . . . . . .11
ANTENNA/CABLE
CONNECTION . . . . . . . . . . . . . . . .11
CONNECTING TO EXTERNAL
INPUT JACKS . . . . . . . . . . . . . . . .12
INSTALLING THE BATTERIES . .12
EXTERNAL INPUT MODE . . . . . .12
CONNECTING TO A STEREO
SYSTEM . . . . . . . . . . . . . . . . . . . .13
CONNECTING TO A STEREO
AMPLIFIER EQUIPPED WITH DIGITAL INPUT JACKS SUCH AS MD
DECK OR DAT DECK (for DVD) .13
CONNECTING TO A DOLBY
DIGITAL DECODER
OR DTS DECODER (for DVD) . . .14
TV/VCR SECTION
C SET UP FOR USE . . . . . . . . . . . . .15
CHANNEL SET UP
FOR THE FIRST TIME . . . . . . . . .15
DELETING (OR ADDING)
CHANNEL . . . . . . . . . . . . . . . . . . .15
CHANNEL SET UP AGAIN . . . . . .16
SELECTING THE LANGUAGE . .16
DAYLIGHT-SAVING TIME . . . . . .16
CLOCK SET UP
(AUTO / MANUAL) . . . . . . . . .17, 18
C TV OPERATION . . . . . . . . . . . . . . .19
WATCHING A TV PROGRAM . . .19
DEGAUSSING . . . . . . . . . . . . . . . .19
PICTURE CONTROL . . . . . . . . . . .19
CLOSED CAPTION SYSTEM . . . .20
V-CHIP SET UP . . . . . . . . . . . . . . .21
C MTS(Multi-Channel Television
sound)SYSTEM . . . . . . . . . . . . . . . .23
CHECKING THE SELECTED
MTS MODE . . . . . . . . . . . . . . . . . .23
MTS RECORDING/MONITOR
MODE . . . . . . . . . . . . . . . . . . . . . .23
SELECTING THE MTS SYSTEM .24
C VIDEO CASSETTE . . . . . . . . . . . . .25
C PLAYBACK . . . . . . . . . . . . . . . . . . .26
NORMAL PLAYBACK . . . . . . . . .26
TRACKING ADJUSTMENT . . . . .26
SLOW MOTION . . . . . . . . . . . . . .26
PICTURE SEARCH . . . . . . . . . . . .26
STILL PICTURE . . . . . . . . . . . . . .26
VERTICAL HOLD CONTROL . . .26
C SPECIAL PLAYBACK . . . . . . . . . .27
RENTAL PLAYBACK . . . . . . . . . .27
AUTO REPEAT PLAYBACK . . . . .27
C SEARCH . . . . . . . . . . . . . . . . . . . . .28
ZERO RETURN . . . . . . . . . . . . . . .28
TIME SEARCH . . . . . . . . . . . . . . .28
INDEX SEARCH . . . . . . . . . . . . . .29
C SPECIAL FEATURES . . . . . . . . . .29
REAL TIME TAPE COUNTER . . .29
AUTO REWIND-EJECT . . . . . . . .29
C RECORDING . . . . . . . . . . . . . . . . .30
NORMAL RECORDING . . . . . . . .30
SKIPPING UNWANTED SCENES
DURING
RECORDING . . . . . . . . . . . . . . . . .30
OTR (One Touch Recording) . . . . . .31
COPYING A VIDEO CASSETTE
(Requires a VCR or camcorder) . . .31
C TIMER . . . . . . . . . . . . . . . . . . . . . .32
AUTOMATIC
TIMER RECORDING . . . . . . . . . .32
TIMER PROGRAM EXTENSION .33
HINTS FOR AUTOMATIC TIMER
RECORDING . . . . . . . . . . . . . . . . .34
AUTO RETURN . . . . . . . . . . . . . . .34
SLEEP TIMER . . . . . . . . . . . . . . . .34
C ON SCREEN DISPLAY . . . . . . . . .35
C CABLE CHANNEL
DESIGNATIONS . . . . . . . . . . . . . .35
SLOW FORWARD / SLOW
REVERSE . . . . . . . . . . . . . . . . . . . .38
ZOOM . . . . . . . . . . . . . . . . . . . . . .38
C SEARCH FUNCTION . . . . . . . . . . .39
TRACK SEARCH . . . . . . . . . . . . .39
TITLE / CHAPTER SEARCH . . . .39
TIME SEARCH . . . . . . . . . . . . . . .39
MARKER SETUP SCREEN . . . . . .39
C SPECIAL PLAYBACK FUNCTION . . .40
REPEAT . . . . . . . . . . . . . . . . . . . . .40
PROGRAM . . . . . . . . . . . . . . . . . . .40
RANDOM PLAYBACK . . . . . . . . .40
C PLAYING A MP3 DISC . . . . . . . . . .41
MP3 PLAYBACK . . . . . . . . . . . . . .41
TRACK SELECTION . . . . . . . . . . .41
PROGRAM . . . . . . . . . . . . . . . . . . .41
RANDOM PLAYBACK . . . . . . . . .41
C CHANGING THE SETTINGS . . . .42
SUBTITLE LANGUAGE . . . . . . . .42
AUDIO LANGUAGE . . . . . . . . . . .42
STEREO SOUND MODE . . . . . . . .42
CAMERA ANGLE . . . . . . . . . . . . .42
BLACK LEVEL SETTING . . . . . . .42
VIRTUAL SURROUND . . . . . . . . .42
C THE ON-SCREEN INFORMATION . . .43
C CHANGING THE DVD SETUP
ITEMS . . . . . . . . . . . . . . . . . . . . . . .44
LANGUAGE SETTING . . . . . . . . .44
DISPLAY SETTING . . . . . . . . . . . .45
AUDIO SETTINGS . . . . . . . . . . . .45
PARENTAL CONTROL . . . . . . . . .46
C TROUBLESHOOTING GUIDE . . .47
C MAINTENANCE . . . . . . . . . . . . . . .50
DISC HANDLING . . . . . . . . . . . . .50
C SPECIFICATIONS . . . . . . . . . . . . .51
DVD SECTION
C WARRANTY . . . . . . . . . . .Back Cover
C ABOUT THE DISCS . . . . . . . . . . . .36
PLAYABLE DISCS . . . . . . . . . . . .36
DISC TYPES . . . . . . . . . . . . . . . . .36
C PLAYING A DISC . . . . . . . . . . . . . .37
BASIC PLAYBACK . . . . . . . . . . . .37
GENERAL FEATURES . . . . . . . . .37
DISC MENU . . . . . . . . . . . . . . . . .37
TITLE MENU . . . . . . . . . . . . . . . . .37
RESUME . . . . . . . . . . . . . . . . . . . .38
PAUSE . . . . . . . . . . . . . . . . . . . . . .38
STEP BY STEP PLAYBACK . . . . .38
FAST FORWARD/REVERSE
SEARCH . . . . . . . . . . . . . . . . . . . .38
-6-
EN
1C29
TD851/951(P01-35).QX33
03.3.1 1:53 PM
Page 7
FEATURES
TV/VCR Mode
• Hi-Fi system–The Hi-Fi stereo recording system
• 2 Step picture search operation–You can view a
•
• Three different playback tape speeds : SP/LP/SLP
• Two different recording tape speeds : SP/SLP
• Auto Head Cleaner–Automatically cleans video
•
•
offers you excellent sound quality with a dynamic
range of 80dB, frequency response from 20Hz to
20kHz, and 0.005% wow and flutter.
Rotary 4-head Record/Playback System–Four heads
ensure excellent picture quality and special effects playback.
Index Search–Fast-forwards to start of next recording.
Slow Motion–View recorded program at slower
than normal speed.
• Infrared remote control
• Trilingual on screen tv/vcr setup display selec•
video program at a high speed or super high speed
in either a forward or reverse direction in LP and
SLP mode. For SP mode only high speed.
•
•
table in English or Spanish or French
Real time counter–This shows the elapsed recording
•
or playback time in hours, minutes, and seconds. The
“–” indication will appear when the tape is rewound
further than the tape counter position “0:00:00”.
•
• 181 channel capability PLL frequency synthesiz-
•
be necessary to view scrambled cable channels.)
•
er tuner with direct station call–(A converter may
• Auto Clock Setting–Allows you to set the clock
function from a PBS broadcast station.
• Closed caption system–You may view specially
•
labeled (cc) TV programs, movies, news, prerecorded tapes, etc. with either a dialogue caption or
text display added to the program.
Auto power on and off system–Automatically
turns on the TV/DVD/VCR when you insert the
cassette, turns off after auto-rewind, and ejects
when the beginning of the tape is reached.
•
• 1 Year, 8 events (including Daily and Weekly
Timer Recording)–The built-in timer allows you to
• Auto rewind when the end of a tape is
reached–This function doesn’t occur when using
timer recording.
• Smooth mode change–TV/VCR mode, DVD
heads as you insert or remove a cassette.
Zero Return–The tape returns to counter of
0:00:00 by rewinding or fast forwarding.
Still–“Freeze” the picture at any time, for close
viewing of a particular scene.
Digital Auto Tracking (DTR)–Automatically
adjusts the tracking for each tape you play.
Rental play mode–Improves playback picture
quality from worn tapes, such as rental tapes.
Auto repeat–Allows you to repeat the playing of a
tape indefinitely without pressing the PLAY button.
Time search–Let you set the TV/DVD/VCR to
advance the tape by entering the desired playback
time you want to skip.
OTR (One Touch Recording)–Instant timed
recording from 30 to 480 minutes is possible at the
push of the REC/OTR button.
•
mode automatically changes without control.
•
•
record up to 8 programs at different times on different channels up to 1 year in advance. The Daily
timer allows recordings to be made of daily broadcasts, and the Weekly timer allows recording to be
made once a week up to the end of the tape.
Auto return–After timer recording is finished, the
TV/DVD/VCR can return to the beginning of the
recording.
Sleep timer–Allows you to have the TV/DVD/VCR
automatically turn on or off at a desired time.
Timer Program Extension–Allow you to shift the
time schedule for automatic timer recording.
V-CHIP–Enables parents to prevent their children
from watching inappropriate material on TV.
A NOTE ABOUT RECYCLING
This product’s packaging materials are recyclable and can be reused. Please dispose of any materials in
accordance with your local recycling regulations.
Batteries should never be thrown away or incinerated but disposed of in accordance with your local regulations concerning chemical wastes.
-7-
EN
1C29
TD851/951(P01-35).QX33
03.3.1 1:53 PM
Page 8
DVD Mode
¡On-screen display
¡Dolby Digital sound
This player can handle Dolby Digital surround
sound having 5.1 channels when connected to a
Dolby Digital decoder.
Information about the current operation can be displayed on a TV screen, allowing you to confirm the
currently active functions (such as program playback), on the TV screen using the remote control.
¡Still/fast/slow/step playback
Various playback modes are available including still
pictures, fast forward/reverse, slow motion and step
frames.
¡Random playback for audio CD and MP3
This player can shuffle the order of tracks to play
them in random order.
¡Search
Chapter search / Title search / Track search / Time
search
¡Repeat
Chapter / Title / Track / Group / All / A-B
¡Zoom
¡Program playback for audio CD and MP3
You can program the order of tracks to play them in
any desired order.
¡DVD menus in a desired language
You can display DVD menus in a desired language,
if available on a DVD.
¡Screen saver/Auto power-off functions
The screen saver program starts when there is no
input from the player for five minutes in the stop
mode. When the screen saver program is activated
for 15 minutes, the power automatically turns off.
Magnified screen can be displayed.
¡Marker
The part designated by user can be called back.
¡Resume Play
User can resume to playback from the part at which
the play was stopped.
¡Virtual Surround
¡Bit rate indication
¡DRC (Dynamic range control)
You can control the range of sound volume.
¡Subtitles in a desired language
You can select a desired language for the display
subtitles, if that language is available on a disc.
¡Selecting a camera angle
You can select the desired camera angle, if a disc
contains sequences recorded from different angles.
¡Choices for audio language and sound mode
You can select the desired audio language and sound
mode, if different languages and modes are available
on a disc.
¡Parental lock
You can set the control level to limit playback of
discs which may not be suitable for children.
¡Automatic detection of discs
This player automatically detects if the loaded disc is
DVD, audio CD or MP3 on disc.
¡Playback MP3 disc
NOTE:
• We do not recommend the use of universal remote controls. Not all of the functions may be controlled with
a universal remote control.
If you decide to use a universal remote control with this TV/VCR/DVD, please be aware that the code number given may not operate this TV/VCR/DVD. In this case, please call the manufacturer of the universal
remote control.
-8-
EN
1C29
TD851/951(P01-35).QX33
03.3.1 1:53 PM
Page 9
OPERATING CONTROLS AND FUNCTIONS
- TV/DVD/VCR FRONT PANEL - [Fig.1]
DVD buttons
POWER
VOLUME
SKIP
PLAY
SKIP
STOP
TV/VCR buttons
SELECT
OPEN/CLOSE
CHANNEL
REC/OTR
REW
PLAY
F.FWD
STOP/EJECT
HEADPHONE
DVD
SEARCH
1
2
3 4 3
5
VIDEO
L
AUDIO
R
TV/VCR
6
7 8 9 10 11 12 13 14 4 15 16 17 18 19 20 21
5. STOP Button [P.37]
[Fig. 2]
- REMOTE CONTROL Stops operation of the disc.
6. OPEN/CLOSE Button [DVD P.37]
Press to insert discs into or remove them from the
tray.
POWER PICTURE SLEEP SELECT
7. Disc loading tray
1
45
8. DVD Indicator
44
22
1
2
3
Lights on during DVD mode.
CH.
11
4
5
6
23
9. SELECT Button
Press to change to TV/VCR mode, external input
7
8
9
mode or DVD mode.
VOL.
PAUSE
+100
2
0
+10
24
10.TV/VCR Indicator
SPEED C.RESET ZOOM
MUTE
Lights on during TV/VCR mode.
25
43
26
11. CHANNEL K/L Buttons
42
PLAY
Press to select memorized channel.
3 (DVD)
(DVD) 3
15 (TV/VCR)
(TV/VCR) 14
STOP
12. Recording Indicator
DISC
4
5
Flashes during recording. Lights up in the StandRECORD
MENU
13
41
by mode for Timer Recording.
DISPLAY
40
ENTER
27
13. REC/OTR (RECORD)Button [TV/VCR P.30, 31]
39
SETUP
TITLE
RETURN
Press for manual recording. Activates One Touch
28
38
Recording. (OTR is only during TV/VCR mode.)
29
CLEAR SEARCH MODE REPEAT
A-B
37
30
14.
REW Button (for TV/VCR) [TV/VCR P.26]
AUDIO SUBTITLE ANGLE
MODE
Press to rewind the tape, or to view the picture
31
36
rapidly in reverse during playback mode. (Rewind
35
32
Search)
33
34
15. FWD Button (for TV/VCR) [TV/VCR P.26]
Press to rapidly advance the tape, or to view the
picture rapidly in forward during playback mode.
(Forward Search)
16. STOP/EJECT Button [TV/VCR P.28]
1. POWER Button [TV/VCR P.15 / DVD P.37]
Press to stop the tape motion. Press in the Stop
Press to turn the power on and off.
mode to remove tape from the TV/VCR/DVD.
2. VOLUME X/Y Buttons
17.
Remote sensor window
Press to control the volume level for the DVD and TV.
18.
HEADPHONE Jack
3. SKIP Buttons (for DVD)[P.38]
To connect headphone (not supplied) for personal
Press once to skip chapters or tracks to a desired
listening.
point.
19.
VIDEO input Jack
Press and hold to change forward or reverse playConnect to the video output jack of a video
back speed.
camera or VCR.
4. PLAY Button [TV/VCR P.26 / DVD P.37]
Starts playback of the disc or tape contents.
-9-
EN
1C29
TD851/951(P01-35).QX33
03.3.1 1:53 PM
Page 10
- TV/DVD/VCR REAR PANEL - [Fig.3]
ANT.
1
L
AUDIO OUT
R
COAXIAL
46
47
20. AUDIO L/R input Jacks
Connect to the audio output jacks of a video
camera or VCR.
21. Cassette compartment
22. PICTURE Button
Press to adjust the picture.
23. Number Buttons
48 49
31. MODE Button [DVD P.41]
Activates program playback or random playback mode.
32. SEARCH MODE Button [DVD P.39]
Press to locate a desired point.
33. AUDIO Button [DVD P.42]
Press to select a desired audio language or sound
mode.
34. SUBTITLE Button [DVD P.42]
Press to select a desired subtitle language.
35. REPEAT Button [DVD P.42]
Repeats playback of the current disc, title, chapter
or track.
36. ANGLE Button (DVD mode) [DVD P.42]
Press to change the camera angle to see the
sequence being played back from a different angle.
37. A-B REPEAT Button [DVD P.40]
Repeats playback of a selected section.
38. RETURN Button
Returns to the previous operation in the DVD
setup mode.
39. ENTER Button
Press to accept a setting.
40. Arrow Buttons
TV Mode:[P.15]
Press two digits to directly access the desired
channel.
Remember to press a "0" before a single digit
channel.
+100 Button–
Press to select cable channels which are equal or
greater than number 100.
DVD Mode:
Press to enter the desired number.
+10 Button–
Press to enter the desired numbers which are
equal or greater than number 10.
24. PAUSE Button [TV/VCR P.26 / DVD P.38]
Pauses the current disc or tape operation.
25. SPEED Button [TV/VCR P.30]
Press to choose the desired recording speed:
SP/SLP.
26. C.RESET Button [TV/VCR P.28]
Press to reset counter to 0:00:00.
Press to cancel a setting of timer program. (See
page 33.)
27. DISPLAY Button
TV/VCR Mode:
Press to select a setting mode from the menu on
the TV screen.
Press to select or adjust from a particular menu.
DVD Mode:
Use when making settings while watching the
display on a TV screen.
TV/VCR Mode:
Display the counter or the current channel number
and current time on the TV screen.
DVD Mode:[P.43]
Displays the current status on the TV screen for
checking purposes.
28. SETUP Button [TV/VCR P.15] [DVD P.44-46]
Press to enter or exit the TV menu or DVD setup
mode.
29. TITLE Button [DVD P.37]
Displays the title menu.
30. CLEAR Button
Resets a setting.
41. DISC MENU Button [DVD P.37]
Displays the menus in the DVD.
42. ZOOM Button [DVD P.38]
Enlarges part of a DVD-reproduced image.
43. MUTE Button
Mutes the sound. Press it again to resume sound.
44. SLEEP Button [TV/VCR P.34]
Sets the Sleep Timer.
45. SELECT Button
Press to switch TV/VCR and DVD mode. You can
see the mode (TV/VCR or DVD) on the front
panel indicator.
- 10 -
EN
1C29
TD851/951(P01-35).QX33
03.3.1 1:53 PM
Page 11
46. ANT. in Jack
Connect to an antenna, cable system, or satellite
system.
47. Power cord
Connect to a standard AC outlet (120V/60Hz).
NOTE: Remove the power cord from the hook to
avoid breaking a wire before you connect
to a standard AC outlet.
48. COAXIAL digital audio out Jack
Connect to the digital input of an external
amplifier or decoder for DVD audio only.
49. AUDIO L/R output Jack
Connect to the analog audio input of an external
amplifier or decoder.
PREPARATION FOR USE
ANTENNA/CABLE CONNECTION
VHF/UHF Antenna
(Not supplied)
Satellite Box or
Cable Box (Not supplied)
OUT
From Cable
System
From Cable System or
Satellite Dish
IN
75-ohm
Coaxial
Cable
(Not supplied)
UHF Antenna
(Not supplied)
or
ANT.
1
L
AUDIO OUT
R
COAXIAL
75-ohm Coaxial
Cable (Not
supplied)
VHF Antenna (Not supplied)
VHF/UHF
Combiner
(Not supplied)
ANT.
or
[Fig. 4]
or
VHF/UHF SEPARATE ANTENNAS
Flat twin-lead cable
CABLE WITH CONVERTER/
DESCRAMBLER BOX OR SATELLITE
BOX
In some areas it will be necessary to use an outdoor
antenna.
CABLE WITHOUT CONVERTER/
DESCRAMBLER BOX
Use this connection if your cable system connects
directly to your TV/DVD/VCR without a converter
box.
By using this connection you can:
1) Use the TV/DVD/VCR remote to select channels.
2) Program one or more unscrambled channels for
Automatic Timer Recording.
NOTE: This TV/VCR/DVD will ONLY record and
view the same channel.
If your cable service supplies you with a converter
box or if you use a satellite system, you can use the
basic connection shown in the illustration.
By using this connection you can also record scrambled channels. However, channel selection must be
made with the converter box or satellite box. This
means that channels cannot be changed using the
TV/DVD/VCR Remote Control. Unattended timer
recording is limited to one channel at a time.
- 11 -
Antenna/Cable Connections
Continued on the Next Page.
EN
1C29
TD851/951(P01-35).QX33
03.3.1 1:53 PM
Page 12
TO RECORD A SCRAMBLED/UNSCRAMBLED CHANNEL
1. Set the TV/DVD/VCR channel selector to the output channel of the Cable Converter Box or Satellite
Box. (Ex. CH3)
2.Select the channel to record from your Cable
Converter Box or Satellite Box.
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the
NEC that provides guidelines for proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the building as close to the point of cable
entry as practical.
INSTALLING THE BATTERIES
1)Open the battery compartment cover by pressing
the cover on the remote unit in the direction of the
arrow.
2)Insert 2 “AA” penlight batteries into the battery
compartment in the direction indicated by the
polarity (+/-) markings.
3)Replace the cover.
EXTERNAL INPUT MODE
CONNECTING TO EXTERNAL
INPUT JACKS
When you watch a program recorded on an another
source (VCR or video camera), use the audio/video
input jacks on the front of the TV/DVD/VCR.
Connect the audio/video output jacks of another
source to the AUDIO L/R and VIDEO jacks of this
TV/DVD/VCR.
Then press the CHANNEL buttons K/L until "AUX"
appears on the screen.
NOTE:
• When you connect a monaural VCR (another
source) to this TV/DVD/VCR, connect the Audio
output jack of the monaural VCR (another source)
to the AUDIO L jack of this TV/DVD/VCR. The
audio will output in both L and R channel equally.
When using an external input signal (another VCR or
video camera), connect the player’s audio/video output cables to the AUDIO L/R IN/
AUX
VIDEO IN jacks of your
TV/DVD/VCR. Then press the
CHANNEL button K or L until
“AUX” appears on the screen.
To the audio
output jacks
[Another source]
HEADPHONE VIDEO
L-AUDIO-R
Audio/Video
coaxial cable
(not supplied)
etc.
To the video
output jack
[Front of the
TV/DVD/VCR]
[Fig. 5]
- 12 -
EN
1C29
TD851/951(P01-35).QX33
03.3.1 1:53 PM
Page 13
CONNECTING TO A STEREO SYSTEM
ANT.
1
L
AUDIO OUT
Stereo system
R
COAXIAL
To ANALOG AUDIO INPUT jacks
To Right (red) and Left (white)
AUDIO OUT jacks
[Fig. 6]
NOTES:
• Be sure to turn off the power to all components in the system before connecting another component.
• Refer to the Owner's Manuals for your stereo system and any other components to be connected to the
TV/DVD/VCR.
CONNECTING TO A STEREO AMPLIFIER EQUIPPED WITH DIGITAL INPUT JACKS SUCH AS MD DECK OR DAT DECK (for DVD)
Use an audio coaxial digital cable available at retail for the audio connections.
Connecting to an amplifier equipped with digital input jacks such as MD Deck or DAT Deck.
ANT.
1
L
AUDIO OUT
R
COAXIAL
Amplifier equipped with digital
input jacks, MD deck,
DAT deck, etc.
To COAXIAL DIGITAL
AUDIO INPUT jack
To DIGITAL AUDIO OUT
(PCM/BITSTREAM)
COAXIAL jack
(only DVD AUDIO OUT)
[Fig. 7]
NOTES:
• The audio source on a disc in a 5.1 channel Dolby Digital surround format cannot be recorded as digital
sound by an MD or DAT deck.
• Be sure to turn off the power to all components in the system before connecting another component.
• Refer to the Owner's Manuals for the components to be connected to the TV/DVD/VCR.
• Set Dolby Digital to OFF for audio output in the setup mode. Playing a TV/DVD/VCR using incorrect settings may generate noise distortion, and may also damage the speakers.
- 13 -
EN
1C29
TD851/951(P01-35).QX33
03.3.1 1:53 PM
Page 14
CONNECTING TO A DOLBY DIGITAL DECODER (for DVD)
If using this TV/DVD/VCR to play a DVD disc in a 5.1 channel Dolby Digital surround format, the
TV/DVD/VCR outputs a DOLBY DIGITAL Data stream from its COAXIAL digital audio out jack. By hooking the player up to a Dolby Digital decoder, you can enjoy a more convincing, realistic ambience with powerful and high-quality surround sound as enjoyed in movie theaters.
Use audio coaxial digital cables available at retail for the audio connections.
Front speaker
(left)
Center
speaker
Front speaker
(right)
ANT.
1
L
AUDIO OUT
R
COAXIAL
Dolby Digital
decoder
Surround
speaker
(left)
To COAXIAL DIGITAL
AUDIO INPUT jack
Surround
speaker
(right)
To DIGITAL AUDIO OUT
(PCM/BITSTREAM)
COAXIAL jack
Subwoofer
[Fig. 8]
NOTES:
• Be sure to turn off the power to all components in the system before connecting another component.
• Refer to the Owner's Manuals for the components to be connected to the TV/DVD/VCR.
• If connected to a Dolby Digital decoder, set DOLBY DIGITAL to ON for audio output in the setup mode.
(See page 45 to set DOLBY DIGITAL to ON.)
• Unless connected to a Dolby Digital decoder, set DOLBY DIGITAL to OFF for audio output in the setup
mode. Playing a TV/DVD/VCR using incorrect settings may generate noise distortion, and may also damage the speakers.
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are
trademarks of Dolby Laboratories.
- 14 -
EN
1C29
TD851/951(P01-35).QX33
03.3.1 1:53 PM
Page 15
TV/VCR SECTION
SET UP FOR USE
You can program the tuner to scan all the channels you receive in your area.
NOTE: Channel memory programming is NOT needed when connected to a cable box or satellite box. Just
select the TV/DVD/VCR channel selector to the output channel of the cable box or satellite box (Ex CH3).
Then select the channel to be viewed on the Cable Box or Satellite Box.
CHANNEL SET UP FOR THE
FIRST TIME
DELETING (OR ADDING)
CHANNEL
TV/VCR
1
Plug in the TV/DVD/VCR power
The channels you no longer receive or seldom watch
can be deleted from the memory. (Of course, you can
add the deleted channel into the memory again.)
cord
Plug the TV/DVD/VCR power cord
into a standard AC outlet.
NOTE:
• If some digits appear in the corner of
the screen, press the POWER button without
unplugging the power cord.
2
TV/VCR
1
Turn on the TV/DVD/VCR
Press the POWER button to turn on the TV/DVD/VCR.
3
Select “ENGLISH” or
“ESPAÑOL”=Spanish or
“FRANÇAIS” =French using the
ENTER button. “[ ]” indicate the
selected language.
4
Begin auto preset
– SET UP –
B LANGUAGE
[ENGLISH] ESP
2
Select “ADD/DELETE CH”
Press the Arrow button K or L to
point to “ADD/DELETE CH”.
Press the ENTER button.
Select “ENGLISH” or “ESPAÑOL” or
“FRANÇAIS”
Select “CHANNEL SET UP”
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
point to “CHANNEL SET UP”.
Then, press the ENTER button.
- TV/VCR SETUP TIMER PROGRAMMING
SETTING CLOCK
B CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
– CHANNEL SET UP –
B ADD / DELETE CH (TV)
AUTO PRESET
FRA
AUTO PRESET
3
– SET UP –
Press the Arrow button K or L to
point to “AUTO PRESET”.
Then press the ENTER button.
The tuner scans and memorizes all
active channels in your area.
NOTES:
• The TV/DVD/VCR distinguishes between standard
TV channels and cable channels.
• If you want to play or record a video tape
BEFORE presetting the tuner, you must press the
SETUP button on the remote control. To preset the
tuner again, see “CHANNEL SET UP AGAIN” on
page 16.
• The TV/DVD/VCR may memorize TV channels as
CATV channels if reception conditions is poor. If
this happens, try AUTO MEMO action again when
reception conditions are better.
LANGUAGE
[ENGLISH] ESP
FRA
Enter the desired channel number
Press the Arrow button K or L until
your desired channel number appears.
(You can also use the number buttons
or the CHANNEL buttons K/L to
enter it) (Example: CH8)
08
ADD / DELETE
B AUTO PRESET
5
After scanning
4
Delete (or add) it from (into) memory
Press the ENTER button. The channel number changes
to light red. The channel is deleted from memory.
Added channel: Light blue.
Deleted channel: Light red.
• To delete another channel, repeat steps [3] and [4].
• If you press the ENTER button again, the channel
is memorized again.
• Press the RETURN button to return to TV/VCR
SETUP MENU.
5
Exit the channel setup mode
Press the SETUP button on the remote control to
returns to TV mode.
NOTE: To confirm that channel(s) has been deleted
or added, press the CHANNEL button K or L.
The tuner stops on the lowest memorized channel.
If you want to recall the selected channels, you can
select the desired channel directly with the remote control number buttons or the CHANNEL button K or L.
- 15 -
EN
1C29
TD851/951(P01-35).QX33
03.3.1 1:53 PM
Page 16
CHANNEL SET UP AGAIN
TV/VCR
Make sure ...
• Press the POWER button to turn on the
TV/DVD/VCR.
1
Select “CHANNEL SET UP”
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
point to “CHANNEL SET UP”.
Then, press the ENTER button.
2
Begin auto preset
Press the Arrow button K or L to
point to “AUTO PRESET”.
Then, press the ENTER button.
The tuner scans and memorizes all
the active channels in your area.
3
NOTE: If Spanish or French is selected accidentally,
1) Press the SETUP button on the remote control.
2) Press the Arrow button K or L to point to “IDIOMA
[ESPAÑOL]” or “LANGAGE” [FRANÇAIS].
3) Press the ENTER button to select your desired language.
4) Press the SETUP button to exit.
DAYLIGHT-SAVING TIME
- TV/VCR SETUP TIMER PROGRAMMING
SETTING CLOCK
B CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
TV/VCR
Select this feature and the TV/DVD/VCR’s clock
automatically will advance one hour in April, then
reverse one hour in October.
When Daylight-Saving Time is ON, the clock will
change automatically as follows:
• First Sunday of April : At 2 AM the clock immediately changes to 3 AM. Any timer programming
you have set to occur between 2 AM and 3 AM
will not record.
• Last Sunday of October : At 2 AM the clock
immediately changes to 1 AM.
Make sure ...
• Press the POWER button to turn on the
TV/DVD/VCR.
– CHANNEL SET UP –
ADD / DELETE CH (TV)
B AUTO PRESET
After scanning
The tuner stops on the lowest memorized channel.
1
SELECTING THE LANGUAGE
TV/VCR
Make sure ...
• Press the POWER button to turn on the
TV/DVD/VCR.
NOTE: This function effects only the language on
the screen menu and not the audio source.
1
Select “LANGUAGE”
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
point to “LANGUAGE”.
- TV/VCR SETUP TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
B LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
2 Select “ENGLISH” or “ESPAÑOL” or
“FRANÇAIS”
Select “ENGLISH” or “ESPAÑOL”= Spanish or
“FRANÇAIS”= French using the ENTER button.
3
Exit the Language mode
Select “SETTING CLOCK”
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
point to “SETTING CLOCK.”
Then, press the ENTER button.
2
Set “D.S.T.” (Daylight-Saving
Time) to [ON]
Press the Arrow button K or L to
point to “D.S.T.”
Then, press the ENTER button until
[ON] appears.
3
- TV/VCR SETUP TIMER PROGRAMMING
B SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
– SETTING CLOCK –
AUTO CLOCK
[ON]
AUTO CLOCK CH SEARCH
AUTO CLOCK CH
[02]
MANUAL CLOCK SET
B D.S.T.
[ON]
Exit the Daylight-Saving Time mode
Press the SETUP button on the remote control to
return to TV mode.
TO CANCEL THE DAYLIGHT-SAVING
TIME
Repeat steps [1] to [2], select [OFF] using the
ENTER button.
Press the SETUP button on the remote control to
return to TV mode.
- 16 -
EN
1C29
TD851/951(P01-35).QX33
03.3.1 1:53 PM
Page 17
CLOCK SET UP
(AUTO / MANUAL)
6
TV/VCR
The TV/DVD/VCR clock must be set correctly before
VCR timer recording is possible. It is suggested that the
clock be set manually when first setting up the
TV/DVD/VCR. Then, setup auto clock correction which
will periodically correct the setting if necessary.
NOTE: If you cannot receive a station with time signals, auto clock setting cannot be performed. Use
manual setting only.
7
8
1
2
Select “SETTING CLOCK”
Select “MANUAL CLOCK
SET”
Press the Arrow button K or L to
point to “MANUAL CLOCK SET”.
Then, press the ENTER button.
3
Select the month
Press the Arrow button K or L until
your desired month appears.
(Example: May → 05)
Then, press the Arrow button B.
4
Select the day
Press the Arrow button K or L until
your desired day appears.
(Example: 6th → 06)
Then, press the Arrow button B.
5
– MANUAL CLOCK SET –
MONTH DAY
05 / 06
HOUR
YEAR
TUE
2003
MINUTE
05 : ––
PM
– MANUAL CLOCK SET –
MONTH DAY
05 / 06
HOUR
YEAR
TUE
2003
MINUTE
05 : 40
PM
Start the clock
5:40 PM
In the example below, the clock is to be set to:
DATE
May 6th, 2003
SETTING TIME 5:40PM
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
point to “SETTING CLOCK”.
Then, press the ENTER button.
Select the minute
Press the Arrow button K or L until
the desired minute appears.
(Example: 40)
MANUAL CLOCK SETTING
Make sure ...
• TV/DVD/VCR power is turned on.
Select the hour
Press the Arrow button K or L until
your desired hour appears.
(Example: 5, PM)
Then, press the Arrow button B.
- TV/VCR SETUP TIMER PROGRAMMING
B SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
Press the SETUP button on the
remote control.
Although seconds are not displayed,
they begin counting from 00 when
you press the SETUP button on the
remote control. Use this feature to synchronize the
clock with the correct time.
NOTE:
When unplugging the AC cord or if there is a power
failure for more than 3 seconds, you may have to
reset the clock.
TO CHANGE CLOCK SETTING
– SETTING CLOCK –
AUTO CLOCK
[ON]
AUTO CLOCK CH SEARCH
AUTO CLOCK CH
[02]
B MANUAL CLOCK SET
D.S.T.
[OFF]
If you want to change the clock,
1)Follow steps [1] and [2].
2)Select where you want to change using the Arrow
button B or s.
3)Enter correct numbers using the Arrow button K or
L.
4)Press the SETUP button on the remote control to
start the clock.
– MANUAL CLOCK SET –
MONTH DAY
05 / ––
HOUR
YEAR
––– ––––
MINUTE
–– : ––
––
PLEASE NOTE:
If there is no local PBS station in your area or on
your cable system, select “AUTO CLOCK” and
press the ENTER button to turn [OFF] this function.
Then you can manually adjust the clock.
– MANUAL CLOCK SET –
MONTH DAY
05 / 06
HOUR
YEAR
––– ––––
MINUTE
–– : ––
––
Select the year
Press the Arrow button K or L until
your desired year appears.
(Example: 2003)
Then, press the Arrow button B.
– MANUAL CLOCK SET –
MONTH DAY
05 / 06
HOUR
YEAR
TUE
2003
MINUTE
–– : ––
––
- 17 -
EN
1C29
TD851/951(P01-35).QX33
03.3.1 1:53 PM
Page 18
AUTOMATIC CLOCK SETTING
Make sure ...
• The TV/DVD/VCR is turned on.
• Confirm the TV/DVD/VCR is receiving a RF
(Radio Frequency) signal from either an antenna or
cable system connection using the ANT IN jack on
the rear of the TV/DVD/VCR.
NOTE:
• If a cable converter box is being used, make sure it
is powered on.
• You must use the TV/DVD/VCR remote control to
perform the clock setting procedure.
1
- TV/VCR SETUP TIMER PROGRAMMING
B SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
– SETTING CLOCK –
AUTO CLOCK
[ON]
AUTO CLOCK CH SEARCH
B AUTO CLOCK CH
[ 45]
MANUAL CLOCK SET
D.S.T.
[OFF]
Turn off the TV/DVD/VCR
Once the TV/DVD/VCR is turned off , it will periodically check and set the correct date and time.
- TV/VCR SETUP TIMER PROGRAMMING
B SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
Set “AUTO CLOCK” to [ON]
Press the ENTER button until
AUTO CLOCK [ON] appears.
3
5
Select “SETTING CLOCK”
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
select “SETTING CLOCK”.
Press the ENTER button to enter
“SETTING CLOCK” menu.
2
Press the Arrow button K or L to
select “SETTING CLOCK”.
Press the ENTER button to enter
“SETTING CLOCK” menu.
Press the Arrow button L to select
“AUTO CLOCK CH”.
Press the ENTER button, then
press the Arrow button B or s
until you locate Auto Clock Set
station number. See item 3 above.
Press the SETUP button to exit the
screen.
– SETTING CLOCK –
B AUTO CLOCK
[ON]
AUTO CLOCK CH SEARCH
AUTO CLOCK CH
[02]
MANUAL CLOCK SET
D.S.T.
[OFF]
Begin “AUTO CLOCK CH SEARCH”
Press the Arrow button L to select “AUTO CLOCK
CH SEARCH”.
Press the ENTER button.
• The TV/DVD/VCR is now
searching for the station which
contain the auto clock set signal.
The search for a signal may take
up to 20 seconds per channel.
• “_ _” appears at the lower left of
the screen when the search has
ended.
• Auto Clock station- write down
the number(s) that appear on the
screen. These are the auto clock
station(s) in your area. See item
4 below.
• If no number(s) appear on the TV screen, there are
no stations in your area which contain the Auto
Clock signal. Auto Clock Setting is not possible.
Please use Manual Clock Setting on page 17.
Press the SETUP button to exit the screen.
NOTE: During Auto Clock CH Search, the picture
may be distorted. This is normal.
– SETTING CLOCK –
AUTO CLOCK
[ON]
B AUTO CLOCK CH SEARCH
AUTO CLOCK CH
[02]
MANUAL CLOCK SET
D.S.T.
[OFF]
– AUTO CLOCK CH SEARCH –
08
10
13
__
4
Enter the channel number that contains the
Automatic Clock Setting Signal
Press the SETUP button on the remote control.
- 18 -
EN
1C29
TD851/951(P01-35).QX33
03.3.1 1:53 PM
Page 19
TV OPERATION
WATCHING A TV PROGRAM
PICTURE CONTROL
TV/VCR
1
Turn on the TV/DVD/VCR
Press the POWER button to turn on the
TV/DVD/VCR.
2
Select the channel number
Press the CHANNEL button K or L to select your
desired channel number or press the number on the
remote control.
Note for using the Number button on the remote
control:
¡When selecting cable channels which are higher
than 99, press +100 first, then, press the last two
digits. (Example: to select channel 125, first press
“+100” then press “2” and “5”).
¡You must precede single-digit channel numbers
with a zero (For example: 02, 03, 04 and so on).
Remember: If the TV/DVD/VCR is connected to a
cable box or satellite box, the TV/DVD/VCR must
be on CH3 or CH4, then the channel to be viewed
must be selected on the cable box or satellite box.
3
Adjust sound
Press the VOLUME button X or Y
to adjust the volume.
TV/VCR
The TV/DVD/VCR’s picture controls – BRIGHT,
CONTRAST, COLOR, TINT and SHARPNESS –
are preset to factory specifications. Although they are
usually the best, you may need to make some further
adjustments for a natural looking image.
NOTES:
• Procedures must be followed within 5 seconds or
the Picture Control mode will be cancelled.
• When setting the Picture Control, the Game mode
will be cancelled.
Make sure ...
• TV/DVD/VCR power must be turned on.
1
Select “PICTURE CONTROL”
Press the PICTURE button on the remote control.
2
Select item you want to adjust
Press the Arrow button K or L until desired control
is displayed.
BRIGHT
CONTRAST
COLOR
TINT
SHARPNESS
BRIGHT
–PPPPPPPCPPPPPPP+
VOLUME
20
C C C C C CCCCCCC
3
NOTES:
• If you press the CHANNEL button o or p in the
DVD mode, you can change the TV channels.
Even if you turn off the TV/DVD/VCR in the
DVD mode, when you turn it on again, it will go
into the TV/VCR mode.
Adjust the picture control
Press the Arrow button B or s to adjust to your
desired level.
COLOR
Arrow button s
to decrease
brightness
to decrease
contrast
to pale
TINT
SHARPNESS
to purple
to soft
BRIGHT
CONTRAST
DEGAUSSING
TV/VCR
Magnetism from nearby appliances and speakers
might affect the color of the TV picture.
If this happens, move this TV/VCR/DVD away from
the appliance. If the color is still not correct, turn off
using the POWER button, then turn it on again 30
minutes or so later (27” model), or unplug the power
cord, then plug it in again 30 minutes or so later (19”
model).
Arrow button B
to increase
brightness
to increase
contrast
to brilliant
to green
to clear
• If there is a power failure of any kind, the
TV/VCR/DVD will retain its memory for this feature.
- 19 -
EN
1C29
TD851/951(P01-35).QX33
03.3.1 1:53 PM
Page 20
CLOSED CAPTION SYSTEM
1
TV/VCR
You can view specially labeled (cc) TV programs,
movies, news, pre-recorded tapes with either a dialogue caption or text display.
CAPTION mode: By choosing the caption mode, you
can watch dramas, movies and news while captioning
the dialogues and the contents of news.
TEXT mode: By choosing the text mode, you can
watch half screen text information if you want.
1-2: You may get these captions or text information
by selecting either “1” or “2”. Caption “2” is used,
usually for a second language if available.
2
Make sure ...
• TV/DVD/VCR power must be turned on.
- TV/VCR SETUP TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
B CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
Select your desired caption menu
Press the ENTER button until your
desired caption menu appears.
([CAPTION1], [CAPTION2],
[TEXT1] or [TEXT2])
3
NOTE:
Not all programs are broadcast with closed captions.
Your television is designed to provide error free
closed captions from high quality antenna, cable and
VCR signals. Conversely, poor quality signals are
likely to result in caption errors or no captions at all.
Common signal conditions which may cause captions
errors are listed below:
• Automobile ignition noise
• Electric motor brush noise
• Weak snowy reception on TV screen
• Multiplex signal reception displaying picture
ghosts or airplane flutter.
• Playback of poorly recorded or worn VCR tapes.
NOTE:
If the TV/DVD/VCR displays a
black box on the TV screen, this
means that the TV/DVD/VCR is
set to the TEXT mode. To clear
screen, select [CAPTION1], [CAPTION2] or [OFF].
Select “CAPTION”
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
point to “CAPTION”.
- TV/VCR SETUP TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
B CAPTION [CAPTION1]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
Exit the caption setting mode
Press the SETUP button on the remote control to
return to TV mode.
TO CANCEL THE CLOSED CAPTION
SYSTEM
Repeat steps [1] and [2], select [OFF] using the
ENTER button. Press the SETUP button on the
remote control to return to TV mode.
WHEN THE CLOSED CAPTION MODE
IS ON
The On-Screen Display will disappear after 5 seconds.
• It will also disappear when the MUTE button is
pressed, and when the PAUSE button is pressed
while recording.
• If there is a power failure of any kind, the
TV/DVD/VCR will retain its memory for this feature.
- 20 -
EN
1C29
TD851/951(P01-35).QX33
03.3.1 1:53 PM
Page 21
V-CHIP SET UP SUB RATINGS
V-CHIP SET UP
TV/VCR
V-CHIP SET UP
1
Make sure ...
• TV/DVD/VCR is turned on.
1
Select “V-CHIP SET UP”
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
select “V-CHIP SET UP”.
Then, press the ENTER button.
2
Enter Access code
When you select the ratings of TV-Y7,TV-PG,TV-14
or TV-MA you will have the option of selecting sub
rating categories.
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
select “V-CHIP SET UP”. Then,
press the ENTER button.
- TV/VCR SETUP TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
B V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
2
Press the Arrow button K or L to
select “TV RATING”.
Then, press the ENTER button.
4
3
ACCESS CODE
_ _ _ _
Select “TV RATING”
Press the Arrow button K or L to
select “TV RATING”.
Then, press the ENTER button.
4
– V-CHIP SET UP –
B TV RATING
MPAA RATING
CHANGE CODE
Blocking TV programs
– V-CHIP SET UP –
B TV RATING
MPAA RATING
CHANGE CODE
Selecting Sub-Ratings”
Press the Arrow button L to select the sub-rating you
wish to block. Then, press the ENTER button twice.
• When you select [TV-Y7]:
Press the Arrow button L or K to
select “FV” (Fantasy Violence).
Then, press the ENTER button to
select [BLOCK] or [VIEW].
• When you select [TV-PG], [TV14] or [TV-MA]:
Press the Arrow button L or K to
select “D”(Suggestive Dialog),
“L”(Coarse Language),
“S”(Sexual Situation), or
“V”(Violence). Then, press the
ENTER button to select [BLOCK] or [VIEW].
Note: When you select [TV-MA], “D” does not
appear on the TV screen.
• The sub-ratings which set to
[BLOCK] appears next to the rating category in the TV rating
menu.
TV–Y7
Press the Arrow button K or L to
select “TV rating” that you wish to
block.
Press the ENTER button to turn it
[BLOCK].
•When you select the rating category and turn it
[BLOCK], the higher rating will turn [BLOCK]
automatically. Also, the lower rating will turn
[VIEW] automatically.
• When you turn “TV-Y” to [VIEW], then all ratings
will turn to [VIEW] automatically.
B TV–Y
TV–Y7 (
TV–G
TV–PG (
TV–14 (
TV–MA (
)
)
)
)
[VIEW]
[VIEW]
[VIEW]
[VIEW]
[VIEW]
[VIEW]
Selection
TV-Y
TV-Y7
TV-G
TV-PG
TV-14
Rating Category Explanations
Appropriate for all children
Appropriate for children seven and older
General Audience
Parental Guidance suggested.
Unsuitable for children under 14
TV-MA
Mature audience only
5
Enter Access code
ACCESS CODE
_ _ _ _
Select “TV RATING”
- TV/VCR SETUP TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
B V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
Use the number buttons on the
remote control to enter the access
code. (Default code is 0000.)
Use the number buttons on the remote
control to enter the access code.
• For the first time set-up or in the
event the TV/DVD/VCR has lost
power, enter the default code of the numbers:
0000.
3
Select “V-CHIP SET UP”
B FV
[BLOCK]
[BLOCK]
TV–PG
5
[BLOCK]
B D
L
S
V
[BLOCK]
[BLOCK]
[BLOCK]
[BLOCK]
B TV–Y
TV–Y7 (
)
TV–G
TV–PG (DLSV )
TV–14 (DLSV )
TV–MA ( LSV )
[VIEW]
[VIEW]
[VIEW]
[BLOCK]
[BLOCK]
[BLOCK]
Exit the V-Chip setting mode
Press the SETUP button on the remote control to
enter the setting and exit the screen.
Exit the V-Chip setting mode
Press the SETUP button on the remote control to
exit the screen.
- 21 -
EN
1C29
TD851/951(P01-35).QX33
03.3.1 1:53 PM
Page 22
CHANGING V-CHIP BLOCKED PROGRAMMING
Note: To change the rating, the TV must be turned to
a station that is not protected. If the (PROTECTED)
appears on the screen, please change the channel to a
station that is not protected.
1)Follow steps [1] and [2].
2)Press the Arrow button K or L to select "TV RATING". Then, press the ENTER button. Select a TV
rating to be unblocked by pressing the Arrow button K or L.
Then press the ENTER button to unblock the rating.
3)Press the SETUP button on the remote control to
exit the screen.
5
CHANGE ACCESS CODE
To change access code, follow the steps.
1
1
Select “V-CHIP SET UP”
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
select “V-CHIP SET UP”. Then,
press the ENTER button.
2
Enter Access code
2
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
B V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
ACCESS CODE
Enter Access code
Use the number buttons on the remote
control to enter the access code.
The default code is 0000.
3
Use the number buttons on the
remote control to enter the access
code.
Select “V-CHIP SET UP”
Press the SETUP button on the remote control.
Press the Arrow button K or L to select “V-CHIP
SET UP”.
Then, press the ENTER button.
MPAA RATING SET UP
- TV/VCR SETUP -
Exit the V-Chip setting mode
Press the SETUP button on the remote control to
exit the screen.
Select “CHANGE CODE”
Press the Arrow button K or L to
select "CHANGE CODE". Then,
press the ENTER button.
ACCESS CODE
_ _ _ _
– V-CHIP SET UP –
TV RATING
MPAA RATING
B CHANGE CODE
_ _ _ _
4
Enter New code
Use the number buttons to enter
your desired access code in the
NEW CODE space. Then enter the
same code in the CONFIRM
CODE space. V-CHIP SET UP
screen appear on the screen.
• If you enter wrong code, repeat step 4, making
sure you enter the same new code exactly in the
confirm code space.
NEW CODE
XXXX
3
Select “MPAA RATING”
Press the Arrow button K or L to
point to “MPAA RATING”.
Then, press the ENTER button.
4
– V-CHIP SET UP –
_ _ _ _
TV RATING
B MPAA RATING
CHANGE CODE
Select your desired item
Press the Arrow button K or L to
point to your desired item.
Then, press the ENTER button to
select [BLOCK] or [VIEW].
Selection
G
PG
PG-13
R
CONFIRM CODE
G
PG
PG–13
B R
NC–17
X
[VIEW]
[VIEW]
[VIEW]
[BLOCK]
[BLOCK]
[BLOCK]
NC-17
Rating Category Explanations
General Audience
Parental Guidance suggested.
Unsuitable for children under 13
Restricted; under 17 requires accompanying parent or adult guardian
No one under 17 admitted
X
Mature audience only
5
Exit the V-Chip setting mode
Press the SETUP button on the remote control to
exit the screen.
Note: If you unplug the power code or power failure
occurs, the changed access code will be lost and will
return to default (0000). Change your access code
again as necessary.
• When you select the rating category and turn it
•
[BLOCK], the higher rating will turn [BLOCK]
automatically. Also, the lower rating will turn
[VIEW] automatically.
When you turn “G” to [VIEW], then all ratings
will turn to [VIEW] automatically.
- 22 -
EN
1C29
TD851/951(P01-35).QX33
03.3.1 1:53 PM
Page 23
MTS(Multi-Channel Television sound)SYSTEM
You can record or listen to a program in MTS stereo.
CHECKING THE SELECTED MTS MODE
TV/VCR
When you play a VHS tape, or receive a broadcast
on the TV/DVD/VCR tuner channel you are watching,
the status shown below will appear when you press
the DISPLAY button on the remote control.
4]
PLAY B
HIFI
12:00AM
CH 123
STEREO/SAP
3]
2]
1]
SP
COUNT
0:00:00
SAP
Second Audio Program, which means your
program, can also be received in a second
language or sometimes a radio station.
HIFI
High Fidelity which produces better sound
than standard stereo TV/DVD/VCRs.
1] When a program is broadcast in stereo, STEREO
appears on the TV screen.
2] When a program is broadcast in second audio,
SAP appears on the TV screen.
3] When a program broadcast both in stereo and second audio, STEREO and SAP appear on the TV
screen.
NOTE: Although a program may be broadcast in
both stereo and second audio, you cannot
record in both stereo and second audio at
the same time.
4] While the TV/DVD/VCR is set in HIFI stereo
mode and playback mode. HIFI appears on the
TV screen. While the TV/DVD/VCR is set in
monaural(MONO) mode, HIFI disappears from
the TV screen.
NOTE: If you play non-HIFI tapes while the
TV/DVD/VCR is set in HIFI, HIFI will disappear from the TV screen and the
TV/DVD/VCR will play automatically in
monaural.
MTS RECORDING/MONITOR MODE
TV/VCR
Type of broadcast
Regular
(monaural audio)
Stereo broadcast
Bilingual broadcast
Display on
the TV screen
-None-
STEREO/SAP
SELECTION
-Invalid-
STEREO
SAP
-InvalidSTEREO*
L
Main audio
program
Sub audio
program
L
sub audio
program
SAP*
Stereo & Bilingual
broadcast
STEREO
SAP
Hi-Fi audio track(2-channel)
L-channel
R-channel
Mono
Mono
STEREO*
SAP*
R
Main audio
program
Sub audio
program
R
sub audio
program
Normal audio
track
Mono
L+R
Main audio
program
Sub audio
program
L+R
sub audio
program
*You must select the recording mode in TV AUDIO [STEREO] or [SAP] when you record a broadcast.
- 23 -
EN
1C29
TD851/951(P01-35).QX33
03.3.1 1:53 PM
Page 24
SELECTING THE MTS SYSTEM
TV/VCR
TO SELECT MONO MODE
Make sure ...
• TV/DVD/VCR power must be turned on.
You can change the selection to “MONO” if you
want to listen to HIFI tapes in normal audio playback.
1) Press the SETUP button on the remote control.
Press the Arrow button K or L to point to “USER’S
SET UP”.Then, press the ENTER button.
2) Press the Arrow button K or L to point to
“VCR AUDIO”.
3) Press the ENTER button until [MONO] appears.
4) Press the SETUP button on the remote control to
return to TV mode.
TO SELECT HIFI MODE
1
Select “USER’S SET UP”
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
point to “USER’S SET UP”. Then,
press the ENTER button.
2
Select“VCR AUDIO”
Press the Arrow button K or L to
point to“VCR AUDIO”.
- TV/VCR SETUP TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
B USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
– USER’S SET UP –
RENTAL
REPEAT PLAY
AUTO RETURN
B VCR AUDIO
TV AUDIO
[OFF]
[OFF]
[OFF]
[HIFI]
[STEREO]
TO SELECT STEREO, SAP, OR MONO
1
3
Select [HIFI]
Press the ENTER button until
[HIFI] appears.
– USER’S SET UP –
RENTAL
REPEAT PLAY
AUTO RETURN
B VCR AUDIO
TV AUDIO
[OFF]
[OFF]
[OFF]
[HIFI]
[STEREO]
2
4
Select “USER’S SET UP”
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
point to “USER’S SET UP”.
Select “TV AUDIO”
Press the Arrow button K or L to
point to“TV AUDIO”.
To return to TV mode
Press the SETUP button on the remote control to
return to TV mode.
NOTES:
• Normally, “HIFI” should be selected for playback
with HIFI sound.
• When you play non-HIFI tapes, the TV/DVD/VCR
will play automatically in the monaural mode.
• The TV/DVD/VCR records automatically MTS
broadcasts in HIFI stereo sound unless you select
SAP mode recording before you begin recording.
3
- TV/VCR SETUP TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
B USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
– USER’S SET UP –
RENTAL
REPEAT PLAY
AUTO RETURN
VCR AUDIO
B TV AUDIO
[OFF]
[OFF]
[OFF]
[HIFI]
[STEREO]
Select [STEREO], [SAP], or [MONO]
Press the ENTER button until [STEREO], [SAP], or
[MONO] appears.
4
To return to TV mode
Press the SETUP button on the remote control to
return to TV mode.
NOTES:
• You must select the recording mode,either TV
AUDIO [STEREO] or [SAP] when you record a
broadcast.
Refer to “MTS RECORDING/MONITOR
MODE”.
• If you select second audio when second audio is
not
available, the TV/DVD/VCR will record normal
audio.
• The TV/DVD/VCR records automatically MTS
broadcasts in HIFI stereo sound unless you select
SAP mode recording before you begin recording.
- 24 -
EN
1C29
TD851/951(P01-35).QX33
03.3.1 1:53 PM
Page 25
VIDEO CASSETTE
This TV/DVD/VCR will operate with any cassette that has the
mark. For best results,
we recommend the use of high-quality tapes. Do not use poor quality or damaged tapes.
PRECAUTIONS
INSERTING A CASSETTE
• Avoid moisture. Moisture condensation may occur
Insert the cassette in the direction as shown. Push in
gently, but continuously, on the center-back of the
cassette until it is drawn into the TV/DVD/VCR. The
TV/DVD/VCR will automatically turn on.
•
•
•
on the tape if it is moved from a cold place to a
warm place or visa versa. Before using a tape with
these conditions, to avoid damage of the tape and
your TV/DVD/VCR, wait until the tape has
warmed to room temperature and the moisture has
evaporated.
Avoid extreme heat, high humidity and magnetic
fields.
Do not tamper with the cassette mechanism.
Do not touch the tape with your fingers.
Window
WRONG
CORRECT
TWO DIFFERENT TAPE SPEEDS
REMOVING A CASSETTE
Before recording, select the tape speed from : SP
mode (Standard Play) or SLP mode (Super Long
Play).
The table below shows the maximum recording/playback time using T60, T120 or T160 tapes in each
mode.
1)In the Stop mode, press the EJECT button on the
remote control or press the STOP/EJECT button on
the TV/DVD/VCR. The cassette will eject.
2)Pull the cassette out of the cassette compartment.
3)Store the cassette in its case as shown.
Tape Speed
Type of tape
Recording/Playback Time
T60
T120
T160
SP mode
1 hour
2 hours
2-2/3 hours
SLP mode
3 hours
6 hours
8 hours
Note: You can play back a tape recorded in LP mode
(Long Play).
ERASE PREVENTION
You can prevent accidental
erasing of recording by
breaking off the tab on the
back edge of the cassette.
Tab
If you decide to record on
the tape again, cover the
hole with plastic tape.
Transparent Tape
NOTE:
• In DVD mode, Whether the cassette is with tab or
without tab you insert, it doesn’t start playing until
you press the PLAY button.
In TV/VCR mode, if th cassette without tab is
inserted, playback will automatically start.
- 25 -
EN
1C29
TD851/951(P01-35).QX33
03.3.1 1:53 PM
Page 26
PLAYBACK
NORMAL PLAYBACK
SLOW MOTION
TV/VCR
1
Insert a prerecorded tape
If the erase-protection tab has been removed, the
TV/DVD/VCR will start playback automatically.
2
To begin playback
TV/VCR
During pause, press the FWD button to reduce the
playback speed. The TV/DVD/VCR mutes the sound
during slow motion. Press the PLAY button to return
to normal playback.
NOTE: If it is left in the Slow mode for more than
five minutes, the TV/DVD/VCR will automatically
go into the Stop mode.
Make sure ...
• TV/DVD/VCR power must be turned on.
PICTURE SEARCH
PLAY B
Press the PLAY button.
3
To stop playback
TV/VCR
STOP
Press the STOP button when playback is completed.
NOTES:
• If you press the PLAY button (of the TV/VCR side)
in the DVD mode, you can start the VCR playback.
• If you press the SELECT button in the VCR playback, it will stop and the mode will change to the
DVD mode. In addition, the same function operates with the DVD side PLAY button or the
OPEN/CLOSE button.
TRACKING ADJUSTMENT
TV/VCR
• Tracking adjustment will be set automatically
•
•
(Digital Tracking function) when you start playback.
However when playing pre-recorded tapes or tapes
recorded on units other than your own, noise lines
(black and white streaks) may appear on the playback picture. If this occurs, you can adjust the
tracking control manually by pressing the CHANNEL button K or L until the streaks disappear. To
return to the DTR function, stop the tape once and
start playback again.
You can reduce the noise lines by pressing the
CHANNEL button K or L in slow mode, too.
Tracking adjustment in Slow mode will not be set
automatically.
This feature is very useful in finding or skipping over
a particular scene on a tape. In this mode, the sound
will be muted.
1)You may view a video tape at a high speed in
either a forward or reverse direction by pressing
the F.FWD or REW button during playback. (in the
SP / LP / SLP modes)
NOTE:
•If you press the F.FWD or REW button on the
front panel in the DVD mode, the VCR forward
or reverse will start. Please press the STOP /
EJECT button once to stop it, twice to eject it.
2)Press it again and the TV/DVD/VCR will now search
in super high speed. (in the LP / SLP modes only)
NOTE:
• Tapes recorded in the SP or LP mode will display a noise bar on the TV screen and the picture
may revert to Black and White. This is normal.
3)Press the PLAY button to return to normal speed.
STILL PICTURE
TV/VCR
You can view a still picture on the TV screen during playback
(the Still mode). Press the PAUSE button during playback.
Only tapes recorded in the SLP mode will show the least
amount of lines.Press the PLAY button to return to playback.
NOTES:
• You can advance the picture one frame at a time by
pressing the PAUSE button during the Still mode.
• If it is left in the Pause mode for more than five
minutes, the TV/DVD/VCR will automatically
switch to the Stop mode.
VERTICAL HOLD CONTROL
TV/VCR
In the Pause/Still mode only, when the picture begins
to vibrate vertically, stabilize the picture by pressing
the CHANNEL button K or L.
NOTE:
If there are video noise lines on the screen, see Tracking
Adjustment section.
- 26 EN
1C29
TD851/951(P01-35).QX33
03.3.1 1:53 PM
Page 27
SPECIAL PLAYBACK
Make sure ...
• TV/DVD/VCR power must be turned on.
• Insert a prerecorded tape.
AUTO REPEAT PLAYBACK
TV/VCR
RENTAL PLAYBACK
TV/VCR
This function enables you to improve the picture
quality when playing back worn cassettes such as
rented tapes.
1
Select “USER’S SET UP”
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
point to “USER’S SET UP”.
Then, press the ENTER button.
2
Set “RENTAL” to [ON]
Press the Arrow button K or L to
point to “RENTAL”.
Press the ENTER button until [ON]
appears.
3
The TV/DVD/VCR has the auto repeat function that
allows you to repeat a tape indefinitely without
touching the PLAY button.
ALL REPEAT: Repeat playback from the beginning
to the end of the tape.
BLANK REPEAT: Repeat playback from the beginning to a blank part, which is blank for more than
10 seconds.
- TV/VCR SETUP TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
B USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
1
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
point to “USER’S SET UP”.
Then, press the ENTER button.
- TV/VCR SETUP TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
B USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
– USER’S SET UP –
B RENTAL
REPEAT PLAY
AUTO RETURN
VCR AUDIO
TV AUDIO
[ON]
[OFF]
[OFF]
[HIFI]
[STEREO]
Exit the Rental setting
2
Start playback
Press the PLAY button to start playback. “RENTAL
PLAY B” appears.
• Once you select the Rental mode, it stays in effect
even after you turn off the TV/DVD/VCR.
TO CANCEL THE RENTAL MODE
Repeat steps [1] and [2], select [OFF] using the
ENTER button on the remote control. Press the
SETUP button on the remote control to return to TV
mode.
If there is a power failure of any kind, the
tv/vcr/dvd will retain its memory for this feature.
Select “ALL” or “BLANK”
Press the Arrow button K or L to
point to “REPEAT PLAY”.
Press the ENTER button repeatedly
until your desired selection [ALL]
or [BLANK] appears.
Press the SETUP button on the remote control to
return to the TV mode.
4
Select “USER’S SET UP”
3
– USER’S SET UP –
RENTAL
B REPEAT PLAY
AUTO RETURN
VCR AUDIO
TV AUDIO
[OFF]
[ALL]
[OFF]
[HIFI]
[STEREO]
Exit the Repeat Play setting
Press the SETUP button on the remote control to
return to the TV mode.
4
Start playback
Press the PLAY button to start the Repeat Play.
”REPEAT PLAY B” appears.
• Once you select the Repeat Play mode, it stays in
effect even after you turn off the TV/DVD/VCR.
• If the Rental mode is set [ON], the “RENTAL
PLAY B” display has priority.
TO CANCEL THE REPEAT PLAY MODE
Repeat steps [1] and [2], select [OFF] using the
ENTER button on the remote control. Press the
SETUP button on the remote control to return to TV
mode.
If there is a power failure of any kind, the
TV/DVD/VCR will retain its memory for this feature.
- 27 -
EN
1C29
TD851/951(P01-35).QX33
03.3.1 1:53 PM
Page 28
SEARCH
Make sure ...
• TV/DVD/VCR power must be turned on.
• Insert a tape.
• This function will not operate in recording mode.
• This function is not operative when a cassette tape
ZERO RETURN
TV/VCR
This function allows you to search easily a beginning
point that you want to review by rewinding or fast
forwarding.
NOTE:
Zero Return WILL NOT work on a blank tape or a
blank portion of a tape.
1
Reset the counter to 0:00:00
Press the C.RESET button repeatedly.
3
Insert a tape.
2
Select “TIME SEARCH” mode
3
- TV/VCR SETUP TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
B TIME SEARCH
INDEX SEARCH
Enter your desired time
Press the Arrow button K or L until
your desired time appears.
(Example: “2:50” stands for 2 hours
50 minutes)
If you wish to cancel the Time
Search at this point, press the SETUP button on the
remote control.
TIME SEARCH
2 : 50
Begin recording or playback
Press the RECORD or PLAY button.
Press the STOP button when recording or playback is
completed.
4
1
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
point to “TIME SEARCH”.
Then, press the ENTER button.
Stop a tape at your desired point
Rewind or fast forward the tape to the beginning
point at which you want to review.
2
is not inserted in the TV/DVD/VCR.
In the example below: To watch a program after 2
hour 50 minutes from the present position, in either
direction.
To activate “ZERO RETURN” mode
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
point to “ZERO RETURN”.
Then, press the ENTER button.
The counter will appear on the TV screen.
The tape will automatically stop when the counter
returns to 0:00:00.
- TV/VCR SETUP -
TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
B ZERO RETURN
TIME SEARCH
INDEX SEARCH
4
Begin Time Search
By pressing the Arrow button s or B, the
TV/DVD/VCR will rewind or fast forward to the
specified point.
The time counts down as the searching progresses.
When 0:00 is reached, the tape will start playback
automatically.
TO CANCEL THE TIME SEARCH at this
point
TIME SEARCH
TV/VCR
The Time Search function makes it possible to quickly advance the tape to your desired position simply
by entering the exact amount of playback time you
want to skip.
NOTES:
• Time Search can be set up to a maximum of 9
hours 50 minutes (9:50) by 10 minutes at a time.
Press the STOP/EJECT button on the TV/DVD/VCR
or the STOP button on the remote control. This will
delete the selected time.
- 28 -
EN
1C29
TD851/951(P01-35).QX33
03.3.1 1:53 PM
Page 29
INDEX SEARCH
1
TV/VCR
This feature provides a method of indexing the starting point so that it can be easily returned to in either
fast forward or rewind mode.
• The index mark will be made automatically when
the REC button is pressed. It will also be marked at
the starting point of Timer recording and OTR.
• The index mark will not be recorded if the PAUSE
button is pressed and released during recording.
• The time gap between making the index marks on
the tape should be greater than 1 minute for SP
recording, 2 minutes for LP recording and 3 minutes for SLP recording.
• In some cases, the index mark at the beginning of
video tape cannot be detected.
Example: You are watching program number 4 and
want to fast forward to program number 7. You
must skip three programs.
CURRENT PLAYBACK PROGRAM
Beginning of tape
Pro.1
4
Pro.2
3
2
- TV/VCR SETUP TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
B INDEX SEARCH
Enter your desired number
Press the Arrow button K or L until
the number of programs that you
want to skip appears.
(Example: “03” for 3 programs)
• The Index Search mode will be
canceled if the procedures are not activated in 30
seconds.
INDEX SEARCH
03
3
Begin Index Search
Press the Arrow button s or B. The TV/DVD/VCR
begins rewinding or fast forwarding to the beginning
of desired program.
NOTE: Every time an index signal is skipped, the
number in the program indicator decreases by one.
End of tape
Pro.3
2
Select “INDEX SEARCH”
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
point to “INDEX SEARCH”. Then,
press the ENTER button.
Pro.4
1
Pro.5
1
Pro.6
2
4
Pro.7
After Index Search
When the preset program is reached, the
TV/DVD/VCR will start playback automatically.
• A video cassette must be inserted in the
TV/DVD/VCR for this function to work.
• The number of Index Searches can be set up to 20.
• This function will not operate in the recording mode.
• When you want to cancel the Index Search while
in progress, press the STOP button.
3
INDEX MARK
SPECIAL FEATURES
REAL TIME TAPE COUNTER
AUTO REWIND-EJECT
TV/VCR
TV/VCR
This shows the elapsed recording or playback time in
hours, minutes, and seconds. (The displayed time will
not change on a blank tape or blank portions on the
tape.)The “–” indication will appear when the tape has
rewound further than “0:00:00” on the tape counter.
• When the end of a tape is reached during record-
•
•
- 29 -
ing, playback, or fast-forward, the tape will automatically rewind to the beginning. After rewinding
finishes, the TV/DVD/VCR will eject the tape and
turn itself to off.
This function is operative when Repeat Play is set
to the [OFF] position.
The tape will not auto-rewind during timer recording or One Touch Recording.
EN
1C29
TD851/951(P01-35).QX33
03.3.1 1:53 PM
Page 30
RECORDING
Make sure ...
• TV/DVD/VCR power must be turned on.
• Insert a cassette tape with its erase prevention tab in place. (If necessary, rewind or fast forward the tape to
the point at which you want to begin recording.)
NOTES:
• This TV/VCR/DVD will ONLY record and view the same channel.
• This TV/VCR/DVD cannot record the contents from the built-in DVD.
SKIPPING UNWANTED
SCENES DURING RECORDING
NORMAL RECORDING
TV/VCR
You can ONLY watch the same TV program that is
being recorded.
1
Select the channel to be
Press the PAUSE button to temporarily stop recording.
Press the PAUSE or RECORD button to resume recording.
NOTES:
• After five minutes, the TV/DVD/VCR will automatically switch to the Recording mode to prevent
tape damage.
• If “CLOSED CAPTION (ON)” is selected, the OnScreen Display will appear for 5 seconds, then disappear.
PAUSE
CH 10
recorded
SP
Press the number buttons on the
remote control or the CHANNEL
button K or L.
Remember: If the TV/DVD/VCR is connected to a
cable box or satellite box, the TV/DVD/VCR must
be on CH3 or CH4, then the channel to be recorded
must be selected on the cable box or satellite box.
2
TV/VCR
Select the tape speed
Press the SPEED button to select
the desired tape speed (SP/ SLP).
SP
3
Begin recording
REC
Press the RECORD button.
SP
4
Stop recording
Press the STOP button when recording is completed.
- 30 -
EN
1C29
TD851/951(P01-35).QX33
03.3.1 1:53 PM
Page 31
Push(es)
1 push
2 pushes
3 pushes
Display
17 pushes
8:00
OTR (One Touch Recording)
TV/VCR
This function enables you to set a recording length
simply by pressing the REC/OTR button on the
TV/DVD/VCR.
Make sure ...
• TV/DVD/VCR power must be turned on.
• Insert a cassette tape with its erase prevention tab in
place. (If necessary, rewind or fast forward the tape to
the point at which you want to begin recording.)
NOTES:
• This function CANNOT be done from the remote
control.
• Recording starts immediately when the REC/OTR
button is pressed.
• When the REC/OTR button is pressed 18 times, the
TV/DVD/VCR returns to the Normal Recording mode.
• To stop the OTR operation, press the STOP button
on the TV/DVD/VCR or on the remote control.
• To show the remaining time, press the DISPLAY
button on the remote control so that “OTR”
appears on the TV screen. (It will show up momentarily then disappear.)
• Recording stops when 0:00 is reached.
• Please note that in the SLP mode maximum recording time, assuming the tape is started at the beginning, is 8 hours using T-160 (or 6 hours using T-120).
• If the tape runs out before the end time, the
TV/DVD/VCR will switch to the Stop mode
immediately, ejects the tape and turns itself off.
• If you press the POWER button during OTR, the
TV/DVD/VCR continues recording until the selected length is reached.
1
2
Select the tape speed
Press the SPEED button to select the desired tape
speed (SP/ SLP).
3
Begin OTR
OTR(2 : 30)
Press the REC/OTR button on the
TV/DVD/VCR as many times as
needed. The recording length will be
determined by the number of times
you press the REC/OTR button. Each
additional push will increase the recording time by 30
minutes. It is set up to 8 hours.
SP
480 minutes
COPYING A VIDEO CASSETTE
(Requires a VCR or camcorder)
TV/VCR
You can make copies of video tapes made by friends
or relatives for your enjoyment.
You can not copy a DVD to a videotape.
WARNING: Unauthorized recordings of
copyrighted video tapes may be an
infringement of copyright laws.
Connect your TV/DVD/VCR and a Source (Playing)
VCR using the following diagram.
[Fig.8]
[The TV/DVD/VCR]
EC/OTR
REW
PLAY
F.FWD
STOP/EJECT
HEADPHONE
VIDEO
L
AUDIO
R
[Ex: Source (playing)
VCR or camcorder]
AUDIO
L
Audio/Video
adapter cable
(not supplied)
Select the channel to be recorded
Press the number buttons on the remote control or
the CHANNEL button K or L.
Remember: If the TV/DVD/VCR is connected to a
cable box or satellite box, the TV/DVD/VCR must
be on CH3 or CH4, then the channel to be recorded
is selected on the cable box or satellite box.
0:30
1:00
Recording length
(normal recording)
30 minutes
60 minutes
IN
OUT
R
VIDEO
OUT
IN
1)Insert a pre-recorded video cassette into the Source
(Playing) VCR or camcorder.
2)Insert a blank video cassette, or one you want to
record over, into the TV/DVD/VCR’s cassette
compartment.
3)Press the SPEED button on remote control for the
TV/DVD/VCR to select the desired recording
speed (SP/SLP).
4)Press the CHANNEL button K or L on the
TV/DVD/VCR until “AUX” appears on the screen.
5)Press the RECORD button on the TV/DVD/VCR.
6)Begin playback of the tape in the source (Playing)
VCR or camcorder.
NOTE: For best results during copying, use the
TV/DVD/VCR’s front panel controls whenever possible. The remote control might affect the source
(Playing) VCR’s playback operation.
- 31 -
EN
1C29
TD851/951(P01-35).QX33
03.3.1 1:53 PM
Page 32
TIMER
AUTOMATIC TIMER
RECORDING
1
Select “TIMER PROGRAMMING”
Press the SETUP button on the
remote control.
Confirm “TIMER PROGRAMMING” is pointed by pressing the
Arrow button K. And press the
ENTER button.
• If you have not yet set the clock, “MANUAL
CLOCK SET” appears. If so, follow stops [3] to
[8] on page 17. Then set the timer recording.
- TV/VCR SETUP -
TV/VCR
You may set the TV/DVD/VCR to start and end a
recording while you are away. You can set 8 programs to record on specific days, daily or weekly
within a 1 year period.
In the example below, the timer is being set to record:
DATE:
July 4th, 2003
SETTING TIME: from 7:30PM to 8:50PM
CHANNEL:
CH61
TAPE SPEED:
SP
Make sure ...
• If a cable box or satellite box is connected with the
TV/DVD/VCR you will be limited to record only one
channel. And the channel selector on the
TV/DVD/VCR must be selected to the output channel
of the boxes CH 3 or CH 4 and then the actual channel to be recorded must be selected on the boxes.
• Clock must be set to the correct time and date
before setting the timer.
• TV/DVD/VCR power must be turn on to program it.
• Insert a cassette tape with its erase prevention tab
in place. (If necessary, rewind or fast forward the
tape to the point at which you want to begin
recording.)
• The channel you want to record is properly set in
advance. (See page 16.)
Avoid over lap of programs ...
There is a chance that a program will not be recorded. when programs overlap;
• The program with an earlier start has priority.
• Once the earliest program finishes, the overlapping
programs will begin recording in sequence.
• The illustration below demonstrates the sequence
of recordings.
Program 1
10:00AM - 11:00AM
Program 2
9:00AM - 10:00AM
Program 3
9:30AM - 12:00PM
B TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
2
Select your desired program
– TIMER PROGRAMMING –
position (1~8)
Press the Arrow button K or L to
select the desired program position.
Then, press the Arrow button B.
3
CH DATE
B -
-
-/-/-/-/-/-/-/-/-
-
BEGIN END
-
-
-
-:-:-:-:-:-:-:-:-
-
-:- -:- -:- -:- -:- -:- -:- -:- -
-
-
Set the channel number
Press the Arrow button K or L until
the desired channel number
appears. (Example: CH61)
Then, press the Arrow button B.
Remember: If the TV/DVD/VCR is
connected to a cable box or satellite box, the
TV/DVD/VCR must be on CH3 or CH4, then the
channel to be recorded is selected on the cable box or
satellite box.
– TIMER PROGRAMMING –
CH DATE
---B 61
-----
4
-/-/-/-/-/-/-/-/-
-
BEGIN END
-
-
-
-:-:-:-:-:-:-:-:-
-
-:- -:- -:- -:- -:- -:- -:- -:- -
-
-
-
-
-
-
-
-
Select once, every day or weekly recording
For once recording :
Press the Arrow button K (up)
until the desired date appears.
(Example: “7/04” for July 4th).
Then, press the Arrow button B.
– TIMER PROGRAMMING –
CH DATE
BEGIN END
- - -/- - - - - -:- - -/- - - - - -:- - -/- - - - - -:B 61 7/04 FRI -:- - -/- - - - - -:- - -/- - - - - -:- - -/- - - - - -:- - -/- - - - - -:-
-
-:- -:- -:- -:- -:- -:- -:- -:- -
For every day recording : To record a TV program
at the same time on the same channel every day.
(Example: Monday through Sunday)
– TIMER PROGRAMMING –
Press the Arrow button L (down)
until “EVRY DAY” appears.
Then, press the Arrow button B.
Recording Sequence
Program 1
10:00AM-11:00AM
Program 2
9:00AM-10:00AM
Program 3
9:30AM-12:00PM
9:00AM
10:00AM
11:00AM
*Recording period is SHADED
12:00PM
CH DATE
BEGIN END
- - -/- - - - - -:- - -/- - - - - -:- - -/- - - - - -:B 61 EVRY DAY -:- - -/- - - - - -:- - -/- - - - - -:- - -/- - - - - -:- - -/- - - - - -:-
-
-:- -:- -:- -:- -:- -:- -:- -:- -
For weekly recording : To record a TV program at
the same time on the same channel every week.
(Example: every Monday)
– TIMER PROGRAMMING –
Press the Arrow button L (down)
until “EVRY” and your desired
day of the week appear together.
Then, press the Arrow button B.
- 32 -
CH DATE
BEGIN END
- - -/- - - - - -:- - -/- - - - - -:- - -/- - - - - -:B 61 EVRY MON -:- - -/- - - - - -:- - -/- - - - - -:- - -/- - - - - -:- - -/- - - - - -:-
-
-:- -:- -:- -:- -:- -:- -:- -:- -
EN
1C29
TD851/951(P01-35).QX33
5
03.3.1 1:53 PM
Set beginning hour
Press the Arrow button K or L until
the desired hour appears.
(Example: “ 7, PM” for 7:30PM)
Then, press the Arrow button B.
6
Set beginning minute
Press the Arrow button K or L until
the desired minute appears.
(Example: “30” for 7:30PM)
Then, press the Arrow button B.
7
Set end hour
Press the Arrow button K or L until
the desired hour appears.
(Example: “8, PM” for 8:50PM)
Then, press the Arrow button B.
8
Set end minute
Press the Arrow button K or L
until the desired minute appears.
(Example: “50” for 8:50PM)
Then, press the Arrow button B.
Page 33
TIMER PROGRAM EXTENSION
– TIMER PROGRAMMING –
CH DATE
BEGIN END
- - -/- - - - - -:- - - -/- - - - - -:- - - -/- - - - - -:- P
B 61 7/04 FRI 7:12 M
- - -/- - - - - -:- - - -/- - - - - -:- - - -/- - - - - -:- - - -/- - - - - -:- -
-:-:-:-:-:-:-:-:-
-
-
-
-
-
– TIMER PROGRAMMING –
CH DATE
BEGIN END
- - -/- - - - - -:- - - -/- - - - - -:- - - -/- - - - - -:- P
B 61 7/04 FRI 7:30 M
- - -/- - - - - -:- - - -/- - - - - -:- - - -/- - - - - -:- - - -/- - - - - -:- -
-:-:-:-:-:-:-:-:-
-
– TIMER PROGRAMMING –
CH DATE
BEGIN END
- - -/- - - - - -:- -:- - - - - -/- - - - - -:- -:- - - - - -/- - - - - -:- -:- - - P
P
B 61 7/04 FRI 7:30 M 8:30 M - - - -/- - - - - -:- -:- - - - - -/- - - - - -:- -:- - - - - -/- - - - - -:- -:- - - - - -/- - - - - -:- -:- - - -
– TIMER PROGRAMMING –
CH DATE
BEGIN END
- - -/- - - - - -:- -:- - - - - -/- - - - - -:- -:- - - - - -/- - - - - -:- -:- - - P
P
B 61 7/04 FRI 7:30 M 8:50 M - - - -/- - - - - -:- -:- - - - - -/- - - - - -:- -:- - - - - -/- - - - - -:- -:- - - - - -/- - - - - -:- -:- - - -
TV/VCR
To shift the time schedule of an automatic timer
recording.
1)Press the POWER button.
2)Repeat step [1] on page 32.
3)Press the RECORD button and select the desired
program using the Arrow button K or L.
4)Press the RECORD button again.
Each additional push will shift forward the
begin/end time for recording by 10 minutes. When
the recording is already in progress, each additional
push will shift forward the end time only. If you
want to cancel while setting, press the PAUSE button on the remote control. The recording time
returns to the original time.
NOTE: When you shift forward the time schedule
during recording, the recording speed will automatically be set to the SLP mode.
5)Press the ENTER or RETURN button to exit the
setting menu. Then press the SETUP button on the
remote control to return to original mode.
TO CORRECT A PROGRAM
9
Set the tape speed
Press the Arrow button K or L
until the desired tape speed
appears. (Example: SP)
10
• While setting a program; press the Arrow button
– TIMER PROGRAMMING –
CH DATE
BEGIN END
- - -/- - - - - -:- -:- - - - - -/- - - - - -:- -:- - - - - -/- - - - - -:- -:- - - P
P
B 61 7/04 FRI 7:30 M 8:50 M SP
- - -/- - - - - -:- -:- - - - - -/- - - - - -:- -:- - - - - -/- - - - - -:- -:- - - - - -/- - - - - -:- -:- - - -
•
Finish setting the program
Press the ENTER or RETURN button. The program
is now completed.
• To set another program, repeat steps [2] to [10].
• Press the SETUP button on the remote control to
return to original mode.
11
Set the timer
Press the POWER button to set automatic timer
recording. The RECORDING indicator lights up.
• You must turn off the TV/DVD/VCR to activate
automatic timer recording.
If power is not turned off and you continue watching TV, “TIMER REC STANDBY” starts flashing
on the TV screen 2 minutes before the programmed
start time.
s to go back one step and enter the correct numbers using the Arrow button K or L.
After setting a program;
1)Press the POWER button.
2)Repeat steps [1] - [2] on page 32.
3)Press the Arrow button B (or press the Arrow
button s to go back one step) until the part you
want to correct begins flashing, then make the
changes pressing the Arrow button K or L.
4)Press the POWER button to set automatic timer
recording.
TO CANCEL AN AUTOMATIC TIMER
RECORDING
• After setting a program;
•
- 33 -
1)Press the POWER button.
2)Repeat steps [1] ~ [2] on page 32 and select a
program you want to cancel.
3)Press the C.RESET button.
4)Press the SETUP button on the remote control to
return to TV mode.
While recording is in progress;
1)Press the POWER button.
2)Press the STOP/EJECT button on the
TV/DVD/VCR.
EN
1C29
TD851/951(P01-35).QX33
03.3.1 1:53 PM
Page 34
TO CHECK THE BEGIN/END TIME
3
1)Press the POWER button so that the RECORDING
indicator goes off.
2)Press the SETUP button on the remote control.
3)Confirm “TIMER PROGRAMMING” is pointed.
4)Press the ENTER button. The details of programs
appear on the TV screen.
5)Press the SETUP button on the remote control to
return to TV mode.
TV/VCR
• Make sure the channel you want to record is prop-
•
•
•
•
•
erly set in advance.
It is not necessary to press the RECORD button for
timer recording.
Recording begins automatically at the Start time.
If you are recording using a Timer mode, you may
not operate the TV/VCR/DVD manually.
The erase-prevention tab on the cassette must be in
place (or you must put tape over the hole).
If the erase-prevention tab is removed, the cassette
will be ejected when the POWER button is pressed
to off.
If the tape runs out before the end time, the
TV/DVD/VCR will switch to the Stop mode
immediately, and the tape will be ejected.
TV/VCR
With this feature, after timer recording is finished,
the beginning of the recorded program(s) can be
searched for automatically.
Select “USER’S SET UP”
Press the SETUP button on the
remote control.
Press the Arrow button K or L to
point to “USER’S SET UP”.
Then, press the ENTER button.
2
Set “AUTO RETURN” to [ON]
Press the Arrow button K or L to
point to “AUTO RETURN”.
Press the ENTER button until [ON]
appears.
4
Watch the recorded program
TO CANCEL THE AUTO RETURN
MODE
Repeat steps [1] and [2], select [OFF] using the
ENTER button.
If there is a power failure of any kind, the
TV/VCR/DVD will retain its memory for this feature.
SLEEP TIMER
TV/VCR
The Sleep Timer function turns off the
TV/DVD/VCR without using the POWER button
after a desired period of time.
NOTE:
• This function does not operate during Recording
mode.
1
AUTO RETURN
1
When all the timer recordings are completed, the
TV/DVD/VCR will rewind to the beginning of the
recorded program(s).
NOTE:
• If you press the POWER button while tape is
rewinding, the Auto Return will stop.
Press the PLAY button.
HINTS FOR AUTOMATIC
TIMER RECORDING
•
Auto Return will begin
Select “SLEEP TIMER”
Press the SLEEP button on the remote control until
“SLEEP TIMER” appears.
2
Set sleep time
Press the SLEEP button until your
desired sleep time appears.
Each additional push will increase
the time by 30 minutes up to 120
minutes.
After 5 seconds, exit the Sleep Timer setting.
- TV/VCR SETUP TIMER PROGRAMMING
SETTING CLOCK
CHANNEL SET UP
B USER’S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
INDEX SEARCH
SLEEP 120 MINUTES
TO CANCEL THE SLEEP TIMER
Press the SLEEP button on the remote control until
“SLEEP TIMER” appears. Press the SLEEP button
until “SLEEP 0 MINUTES” appears.
– USER’S SET UP –
RENTAL
REPEAT PLAY
B AUTO RETURN
VCR AUDIO
TV AUDIO
[OFF]
[OFF]
[ON]
[HIFI]
[STEREO]
- 34 -
EN
1C29
TD851/951(P01-35).QX33
03.3.1 1:53 PM
Page 35
ON SCREEN DISPLAY
To check the Counter, Clock and Channel number on the TV screen, press the DISPLAY button on the remote
control. Each time you press the DISPLAY button on the remote control, the TV screen will change as follows:
When the Closed Caption mode is OFF:
When the Closed Caption mode is ON:
• Counter mode: After 5 seconds, only the counter
• The On Screen Display disappear after 5 seconds.
• This is true even if the MUTE button is pressed, or
•
remains. To clear it, press the DISPLAY button.
Clock mode: After 5 seconds, only the clock and
the channel number remain. To clear them, press
the DISPLAY button.
OFF mode
Counter mode
OFF mode
Clock mode
STOP
SP
the PAUSE button is pressed while recording.
STOP
COUNT 0:12:34
Clock/Counter mode
5:40PM
CH2
STOP
5:40 PM
CH2
SP
After 5 seconds
After 5 seconds
SP
COUNT 0:12:34
5:40PM
CH2
COUNT 0:12:34
Counter
remains
Clock & Channel
remains
CABLE CHANNEL DESIGNATIONS
If you subscribe to cable TV, the channels are displayed as 1-125. Cable companies often designate channels
with letters or letter-number combinations. Please check with your local cable company. The following is a
chart of common cable channel designations.
CATV channel
5A
2
3
4
5
6
7
8
9
10
11
12
13
A
B
TV Display
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
CATV channel
TV Display
C
16
D
17
E
18
F
19
G
20
H
21
I
22
J
23
K
24
L
25
M
26
N
27
O
28
P
29
Q
30
CATV channel
R
S
T
U
V
W
W+1
W+2
W+3
W+4
W+5
W+6
W+7
W+8
W+9
TV Display
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
CATV channel W+10
TV Display
46
CATV channel W+25
W+11 W+12 W+13 W+14 W+15 W+16 W+17 W+18 W+19 W+20 W+21 W+22 W+23 W+24
47
48
49
50
51
52
53
54
55
56
57
58
59
60
W+26 W+27 W+28 W+29 W+30 W+31 W+32 W+33 W+34 W+35 W+36 W+37 W+38 W+39
TV Display
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
CATV channel W+40 W+41 W+42 W+43 W+44 W+45 W+46 W+47 W+48 W+49 W+50 W+51 W+52 W+53 W+54
TV Display
76
CATV channel W+55
TV Display
91
CATV channel W+65
TV Display
106
CATV channel W+80
TV Display
121
77
78
79
W+56 W+57 W+58
92
93
94
80
81
82
83
84
85
86
A-5
A-4
A-3
A-2
A-1
W+59 W+60 W+61 W+62 W+63 W+64
95
96
97
98
99
100
101
87
102
88
103
89
104
90
105
W+66 W+67 W+68 W+69 W+70 W+71 W+72 W+73 W+74 W+75 W+76 W+77 W+78 W+79
107
108
109
110
111
112
113
114
115
116
117
118
119
120
W+81 W+82 W+83 W+84
122
123
124
125
- 35 -
EN
1C29
TD851/951(P36-52).QX33
03.3.1 1:56 PM
Page 36
DVD SECTION
ABOUT THE DISCS
PLAYABLE DISCS
DISC TYPES
The following discs can be played back on this
TV/DVD/VCR.
¡DVD video
¡DVD-R/RW*
¡DVD+R/RW*
¡Audio CD
¡CD-R/RW*
¡MP3*
* Depending on the types or the writing method of the
medium some discs can not be played.
[DVD]
Data on a DVD is divided into sections called "titles", and
then into subsections called "chapters", each of which is
given a title or chapter number. Playback conditions are
preset on some DVD video discs, and these playback conditions take priority over user operations on this player. If
a function you selected does not run as desired, refer to
the manual accompanying the disc.
Example
• Some DVD-R/RW, DVD+R/RW, or CD-R/RW discs
made on personal computers, or on DVD recorders may
not be played back properly due to the factors such as
scratches, dirt or special properties of the disc.
• Discs made on personal computers may not be played
back properly due to the different environment or the
settings of the application you use. We recommend
always to use the standardized, rightly formatted discs.
(Please contact the sales agency for more detail).
This player conforms to the NTSC color system. You cannot play discs recorded in other color systems such as
PAL or SECAM.
¡Some discs include region codes as shown below.
Title 1
Title 2
Chapter 1 Chapter 2 Chapter 3 Chapter 4 Chapter 1 Chapter 2
[AUDIO CD]
Data on an audio CD is divided into sections called
“tracks”, each of which is given a track number.
Example
Track 1
Track 2
Track 3
Track 4
Track 5
Track 6
¡The number inside the symbol refers to a region of the
world, and a disc encoded in a specific region format
can only be played back on TV/DVD/VCR with the
same region code.
The following discs cannot be played back on this
TV/DVD/VCR.
[MP3]
Data on an MP3 is divided into sections called "groups",
and then into subsections called "tracks", each of which is
given a group or track number.
¡DVD with region codes other than 1 or ALL.
Example
¡DVD-ROM
Group 1
¡DVD-RAM (Never play back, otherwise malfunc-
tion may result.)
Track 1
Track 2
Track 3
Group 2
Track 4
Track 1
Track 2
¡CD-ROM
¡VSD
¡CDV (Only plays back the audio part.)
¡CD-G (Only plays back the sound.)
¡CD-I (Never play back, otherwise malfunction
may result.)
¡SACD
¡Photo CD (Never play back, otherwise malfunc-
tion may result.)
¡Video CD (Never play back, otherwise malfunc-
tion may result.)
Any other discs without compatibility indications.
– 36 –
EN
01A11
TD851/951(P36-52).QX33
03.3.1 1:56 PM
Page 37
PLAYING A DISC
BASIC PLAYBACK
DVD-V
GENERAL FEATURES
CD
Getting started
¡Turn on the power of amplifier and any other com-
ponents, if necessary.
1 Press the POWER button.
¡The power will turn on.
2 Press the OPEN/CLOSE button to open disc
DVD may contain menus to navigate the disc and
access special features. Press the appropriate number
buttons or use the Arrow buttons (L/K/s/B) to highlight your selection in the DVD main menu and press
the ENTER button to confirm.
NOTES
¡Select DVD mode by pressing the SELECT button on
the remote control. Then, operate the DVD functions.
¡Unless stated, all operations described are based on
remote control use. Some operations can be carried
out using the menu bar on the TV screen.
loading tray.
3 Place the chosen disc in the tray, with the
DISC MENU
label facing up.
DVD-V
1 Press the DISC MENU button.
¡The DVD main menu will appear.
2 If the feature is not available,
symbol
may appear on the TV screen.
4 Press the PLAY button.
¡The tray will close automatically, and playback will
3 If disc menu is available on the disc, audio
then start from the first chapter or track of the disc.
If the playback does not start automatically, press
the PLAY button.
¡When you playback the DVD which a title menu is
recorded, it may appear on the screen. In this case,
refer to “TITLE MENU”.
language, subtitle options, chapters for the
title and other options will appear for selection.
4 Press the Arrow buttons (L/K/s/B) to
select an item, and the ENTER button to
confirm selection.
5 Press the STOP button to stop playback.
TITLE MENU
NOTES
¡When the DVD mode has been switched to the
TV/VCR mode, the DVD mode shuts down first and
then TV picture and sound appears in about 4 seconds.
Similarly, when the POWER button is pressed to turn
off in the DVD mode, this mode shuts down first and
then the TV/DVD/VCR’s power is turned off.
¡A “prohibited icon” may appear at
the top-right on the TV screen during operation, warning that a prohibited operation has been encountered by the DVD or the disc.
¡With DVDs that use titles for playback program signals, playback may start from the second title, or it
may skip these titles.
¡During the playback of a two layered disc, pictures
may stop for a moment. This happens when the 1st
layer switches to the 2nd layer. This is not a malfunction.
DVD-V
1 Press the TITLE button.
¡The title menu will appear.
2 If the feature is not available,
symbol
may appear on the TV screen.
3 Press the Arrow buttons (L/K/s/B) to
select an item, and the ENTER button to
confirm selection.
CALLING UP A MENU SCREEN
DURING PLAYBACK
For DVD-Vs
¡Press the DISC MENU button to call up the DVD menu.
¡Press the TITLE button to call up the title menu.
NOTE
¡Contents of menus and corresponding menu operations may vary between discs. Refer to the manual
accompanying the disc for details.
– 37 –
EN
01A11
TD851/951(P36-52).QX33
03.3.1 1:56 PM
Page 38
SLOW FORWARD /
SLOW REVERSE
RESUME
DVD-V
CD
DVD-V
1 During playback, press the STOP button.
¡Resume message will appear on the TV screen.
1 During playback, press the PAUSE button.
2 Press and hold down the FWD g or REV
2 Press the PLAY button, playback will resume
h button for a few seconds.
from the point at which playback was stopped.
3 Each press and hold down the FWD g or
¡To cancel resume, press the STOP button twice.
¡If turn off the TV/DVD/VCR, resume function will
REV h button repeatedly to select the
required speed: 1/16, 1/8, 1/2 of the normal
playback.
be cancelled.
PAUSE
4 To return to normal playback, press the
DVD-V
PLAY button.
CD
1 During playback, press the PAUSE button.
¡Playback will pause and sound will be muted.
2 To continue playback, press the PLAY button.
STEP BY STEP PLAYBACK
Note for using buttons on the main unit:
Press the PAUSE button, then, press and hold down the
SKIP G/ SEARCHg buttons or the SKIPH
/SEARCHh buttons on the TV/DVD/VCR for a few
seconds to begin Search in 1/16 speed of the normal
playback. Press and hold down again to change speed
to 1/8. Repeat this procedure to change to 1/2.
ZOOM
DVD-V
DVD-V
1 During playback, press the PAUSE button.
¡Playback will pause and sound will be muted.
2 The disc goes forward by one frame each
time the PAUSE button is pressed.
3 To exit step by step playback, press the
The Zoom function allows you to enlarge the video
image and to pan through the enlarged image.
1 Press the ZOOM button during playback.
¡Playback will continue.
PLAY button.
2 Press the ZOOM button repeatedly to select
FAST FORWARD/REVERSE
SEARCH
DVD-V
CD
the required zoom factor: ZOOM1, ZOOM2,
ZOOM3, or OFF.
MP3
3 Use the Arrow buttons (K/ L/s / B) to
move the zoomed picture across the
screen.
1 During playback, press and hold down the FWD
g or REV h button for a few seconds.
4 To exit zoom mode, press the ZOOM button
2 Each press and hold down the FWD g or
REV h button repeatedly to select the
required speed: x2, x8, x50, x100.
¡For audio CDs, the speed is fixed at ×16.
¡For MP3, the speed is fixed at ×8.
to OFF.
NOTES
¡Zooming function does not work while disc menu is
shown.
¡Zooming function is not available on some discs.
3 To return to normal playback, press the
PLAY button.
Note for using buttons on the main unit:
During playback, press and hold down the SKIP G/
SEARCHg buttons or the SKIPH/SEARCHh
buttons on the TV/DVD/VCR for a few seconds to begin
Search in x2 speed. Press and hold down again to change
speed to x8. Repeat this procedure to change to x50 and
x100.
– 38 –
EN
01A11
TD851/951(P36-52).QX33
03.3.1 1:56 PM
Page 39
SEARCH FUNCTION
TRACK SEARCH
TIME SEARCH
CD
DVD-V
There are three ways to begin playback on an Audio
CD at a specific Track.
CD
1 During playback, press the SEARCH MODE
button three times (CD: twice) to display the
Time Search on the TV screen.
Using the Number buttons on the remote control
2 Within 30 seconds, enter a desired disc
1 Press the Number buttons to enter the
time using the Number buttons on the
remote control.
desired Track number.
¡Playback will start at the selected track.
¡For single digit tracks (1-9), press a single number
(eg. track 3, press 3).
¡Playback will start at the specified time.
¡Press the CLEAR button to erase the incorrect input.
¡To play track 26, press +10, 2, 6.
MARKER SETUP SCREEN
DVD-V
Using the SEARCH MODE button
1 Press the SEARCH MODE button.
¡The track search display appears.
CD
Use markers to memorise your favorite places on a
disc.
2 Within 30 seconds, select a desired track
1 Press the SEARCH MODE button four times
number using the Number buttons on the
remote control.
(CD: three times) during playback.
¡The display screen and Markers will appear on the
¡For single digits press 0 first.
¡Playback will start at the selected track.
TV screen.
Using the SKIP H G buttons
During playback, press the SKIP G button to move
the next track. Press it repeatedly to skip subsequent
tracks. Press the SKIP H button to go back to beginning of the current track. Press it repeatedly to go to
the previous tracks.
¡If the SKIP button is pressed while the playback is
paused, the playback will be paused again after skipping to the next track.
NOTE
¡The SKIP H G buttons are not available when
playback is stopped.
2 Press the Arrow buttons (s/ B) to select 1,
2, 3, 4, 5, 6, 7, 8, 9, or 10 and ensure that “- :
- - : - -” appears in the display.
3 When reaches the desired point, press the
ENTER button.
¡The Title or Track and elapsed playing time will
appear in the TV screen.
4 To return to the Marker later, press the
SEARCH MODE button four times (CD: three
times) during playback and the Arrow buttons (s/ B) to choose the desired marker,
then press the ENTER button.
TITLE / CHAPTER SEARCH
DVD-V
1 Press the SEARCH MODE button once for
the Chapter search, twice for the Title
search during playback.
/2
NOTES
¡Opening the disc tray or turning off the power or
select AC at step 2 and press the ENTER button will
erase all Markers.
¡To clear a marker, using the Arrow buttons (s/ B),
position the cursor on to the marker number to be
cleared and press the CLEAR button.
¡You can mark up to 10 points.
2 Enter the desired chapter/title number using
the Number buttons on the remote control.
5 Press the SEARCH MODE or RETURN button to exit.
¡Playback will start at the selected Chapter or Track.
¡Press the CLEAR button to erase the incorrect input.
¡For single digits press 0 first.
– 39 –
EN
01A11
TD851/951(P36-52).QX33
03.3.1 1:56 PM
Page 40
SPECIAL PLAYBACK FUNCTION
REPEAT
PROGRAM
REPEAT is available only during playback.
CD
REPEAT TITLE / CHAPTER
DVD-V
To activate the repeat function, press the
REPEAT button during playback.
¡The repeat mode changes as described below every
time you press the button.
You may determine the order in which tracks will play.
1 In stop mode, press the MODE button.
¡The PROGRAM screen will appear.
2 Press the Arrow button ▲ or ▼ to select a
CHAPTER
TITLE
(current chapter repeat) (current title repeat)
OFF
(repeat off)
track, then press the
ENTER button.
TOTAL
¡Press the CLEAR button to
NOTES
¡Repeat Title/Chapter is not available with some
scenes.
¡The REPEAT setting will be cleared when moving
to other title or chapter.
CD
To activate the repeat function, press the
REPEAT button during playback.
¡The repeat mode changes as described below every
time you press the button.
ALL
(entire disc repeat)
OFF
(repeat off)
NOTES
¡Repeat setting will be cleared when moving to other
track.
¡Repeat playback does not function during repeat A-B
playback.
REPEAT A-B
DVD-V
CD
1 Press the REPEAT A-B button at your chosen starting point.
¡
3 Repeat step 2 until you have selected all the
tracks you want to play in the program.
4 Press the PLAY button to play the pro-
REPEAT TRACK
TRACK
(current track repeat)
erase the most recently entered
program.
A- appears briefly on the TV screen.
2 Press the REPEAT A-B button again at your
chosen end point.
grammed tracks.
NOTES
¡While the program is being played back, the STOP
works as follows.
¡Press the STOP button once and then the PLAY button again, playback will restart from the point where
the STOP button was pressed. (Program continued)
¡Press the STOP button twice and then the PLAY button
again, playback will restart from the track in the usual
way. (Program cleared)
¡Up to 99 programs can be entered.
¡If you like to repeat the current track in the program,
press the REPEAT button repeatedly until
TRACK appears during playback. If you like to
repeat the entire program press the REPEAT button
repeatedly until
ALL appears during playback.
RANDOM PLAYBACK
CD
This shuffles the playing order of tracks instead of
playback in the sequence.
1 In stop mode, press the MODE button twice.
¡RANDOM screen appears.
RANDOM
CD [AUDIO]
TOTAL 0:45:55
¡
A-B appears briefly on the TV screen, and the
repeat sequence begins.
RANDOM PROGRAM
- - no indication - -
PLAY
3 To exit the sequence, press the REPEAT AB button.
2 Press the PLAY button to start random playback.
NOTES
¡The repeat A-B section can only be set within the cur- NOTE
rent title (for DVDs), or current track (for audio CDs). ¡If you like to repeat the current track in the random
selection, press the REPEAT button repeatedly until
¡Repeat A-B is not available with some scenes in DVD.
TRACK appears during playback. If you like to
¡To cancel the A point which was set, press the
repeat the entire random selection press the
CLEAR button.
REPEAT button repeatedly until
ALL appears
¡Repeat A-B playback does not function during title,
during playback.
chapter, track or all repeat playback.
– 40 –
EN
01A11
TD851/951(P36-52).QX33
03.3.1 1:56 PM
Page 41
PLAYING A MP3 DISC
MP3 PLAYBACK
TRACK SELECTION
MP3
MP3
When a CD with MP3 files is in the TV/DVD/VCR,
the MP3 menu will appear on the TV screen in stop
mode.
1 Press the SEARCH MODE button during
playback.
¡The FILE LIST will appear.
1 In stop mode, press the Arrow buttons
(K/L) to select the
2 Select a desired track using the Arrow buttons (K/L/s/B).
desired group track.
¡If a group is selected, press
¡Press the Arrow button B when you want to go to
the Arrow B or ENTER button to go on to the track selection screen. Press the Arrow
buttons (K /L ) to choose a
track, then press the ENTER button.
¡If a track is selected, press the ENTER button to start
playing tracks. Starting from the one you’ve just
chosen the subsequent tracks will be played.
¡Choose FIRST PLAY to start playback from the
beginning of the listed tracks.
¡Press the TITLE button to return to the first item.
¡Press the Arrow button s when you want to go back
the next hierarchy.
2 Press the STOP button to stop playback.
NOTES
¡Folders are known as Groups; files are known as
Tracks.
¡MP3 files are accompanied by 3 icon.
¡Maximum of 255 folders can be recognized.
¡Maximum of 256 files can be recognized.
¡Up to 8 hierarchies can be created.
This player recommends the use of files recorded at
the below specifications:
¡Sampling frequency: 44.1kHz or 48kHz
¡Constant bit rate: 112kbps ~ 320kbps.
to the previous hierarchy.
3 Press the PLAY button to start playback.
NOTES
¡Press the SEARCH MODE button to exit.
¡Some selections may take a while to be recognized.
PROGRAM
MP3
This feature allows you to program an MP3 disc to
play in a desired sequence.
1 In stop mode, press the MODE button.
¡The PROGRAM screen will appear.
2 Select a desired track using the Arrow buttons (K/L/s/B). Then, press the ENTER
button.
¡Press the Arrow button B when you want to go to
the next hierarchy.
¡Press the Arrow button s when you want to go back
to the previous hierarchy.
¡Press the CLEAR button to erase the most recently
entered program.
3 Repeat step 2 until you have selected all the
Tracks you want to play in the program.
4 Press the PLAY button to start programmed
playback.
RANDOM PLAYBACK
MP3
1 In stop mode, press the MODE button twice.
¡RANDOM screen appears.
2 Press the PLAY button to start random playback.
– 41 –
EN
01A11
TD851/951(P36-52).QX33
03.3.1 1:56 PM
Page 42
CHANGING THE SETTINGS
SUBTITLE LANGUAGE
CAMERA ANGLE
DVD-V
DVD-V
The DVD allows you to select a language for subtitles
during DVD disc (if available) playback.
Some DVD discs contain scenes which have been shot
simultaneously from various angles. You can change
the camera angle when the (
) icon appears on the
screen.
1 Press the SUBTITLE button during playback.
2 Press the SUBTITLE button repeatedly to
select your desired subtitle language.
¡The subtitle language will be displayed on the dis-
play bar at the top of the screen.
3 To turn off subtitles, press the SUBTITLE
button repeatedly until OFF appears.
NOTES
¡Some discs allow audio language setting/subtitle language
setting on the disc menu. (Operation varies between discs,
so refer to the manual accompanying the disc.)
¡If the desired language is not shown after pressing
the SUBTITLE button several times, the disc does
not have subtitles in that language.
¡If you choose a Language that has a 3 letter language
code, the code will be displayed every time you
change the Subtitle language setting. If you choose
any other languages, ‘---’ will be displayed instead.
(Refer to page 44.)
AUDIO LANGUAGE
DVD-V
The TV/DVD/VCR allows you to select a language
during DVD disc (if multi language available) playback.
1 Press the AUDIO button during playback.
2 Press the AUDIO button repeatedly to select
your desired language.
1 Press the ANGLE button during playback.
¡The selected angle will be displayed on the display
bar at the top of the screen.
2 Press the ANGLE button repeatedly to
select your desired angle.
BLACK LEVEL SETTING
DVD-V
Adjust the Black Level Settings to make the black
parts of the picture brighter.
1 Press the MODE button during playback.
ON
2 Press the ENTER button to switch OFF.
ON: Makes the dark parts brighter.
OFF: Shows the original picture as recorded.
3 Press the MODE button twice or the
RETURN button to exit.
VIRTUAL SURROUND
DVD-V
NOTE
¡Pressing the AUDIO button may not work on some
DVDs with multiple audio languages (e.g. DVDs
which allow audio language setting on the disc menu).
CD
MP3
You can enjoy stereophonic visual space on your existing stereo system.
1 Press the MODE button twice (CD/MP3:
STEREO SOUND MODE
once) during playback.
OFF
CD
1 Press the AUDIO button repeatedly during
playback to select between STEREO, L-CH
or R-CH.
¡STEREO - both right and left channels are active (stereo)
2 Press the ENTER button to set it 1 (Natural
effect) or 2 (Emphasized effect) or OFF.
3 Press the MODE or RETURN button to exit.
L-CH - only left channel is active
NOTE (for CD play only)
R-CH - only right channel is active
¡Virtual Surround will not be effective if the sound
NOTE
mode is set to something other than STEREO.
¡If the Virtual Surround setting is ON, the sound mode
will be fixed to STEREO, and can not be changed.
EN
– 42 –
01A11
TD851/951(P36-52).QX33
03.3.1 1:56 PM
Page 43
THE ON-SCREEN INFORMATION
DVD-V
CD
MP3
You can check the information about the current disc by pressing the DISPLAY button on the remote control.
For DVD-Vs
For audio CDs
1 Press the DISPLAY button during playback
to show current Chapter.
to show the current Track.
¡The elapsed and remaining playing time of the cur-
¡The elapsed and remaining
playing time of the current
chapter will be displayed.
1 Press the DISPLAY button during playback
9/49
rent track will be displayed.
0:00:00 -0:00:00
2 Press the DISPLAY button again to show
2 Press the DISPLAY button again to show
current Total Track.
¡The elapsed and remaining playing time of the cur-
current Title.
¡The elapsed and remaining playing time of the cur-
rent total track will be displayed.
rent title will be displayed.
3 Press the DISPLAY button again to exit the
3 Press the DISPLAY button again.
display.
¡The BIT RATE and the current repeat setting will be
displayed.
¡If you are playing a dual layered disc, the layer num-
ber will also be displayed (L0: Layer 0 is playing.
L1: Layer 1 is playing).
For MP3
1 Press the DISPLAY button during playback.
¡The name of the file currently in play will be displayed.
4 Press the DISPLAY button again to exit the
2 Press the DISPLAY button repeatedly to
display.
show the track number, the repeat status,
and the playback status at the top of the
screen.
¡
will be displayed when repeat play has been
selected.
T - indicates Track repeat
G - indicates Group (folder) repeat
A - indicates Disc repeat
3 Press the DISPLAY button again to exit the
display.
– 43 –
EN
01A11
TD851/951(P36-52).QX33
03.3.1 1:56 PM
Page 44
CHANGING THE DVD SETUP ITEMS
LANGUAGE SETTING
DVD-V
Language options are not available with some discs.
1 Press the SETUP button twice in STOP
mode so that the DVD SETUP menu
appears.
¡ If the menu does not appear, press the PLAY button,
the STOP button, then the SETUP button twice.
QUICK SETUP
TV MODE
DOLBY DIGITAL
4:3 LETTER BOX
ON
2 Press the Arrow button B to select CUSTOM, then press the ENTER button.
¡CUSTOM mode will appear.
3 Press the Arrow buttons (s/ B) to select
LANGUAGE, then press the ENTER button
to confirm.
LANGUAGE
AUDIO
SUBTITLE
DISC MENU
ORIGINAL
OFF
ENGLISH
4 Press the Arrow buttons (K/ L) to select the
next items, then press the ENTER button.
AUDIO:
¡Sets the audio language.
SUBTITLE:
¡Sets the subtitle language.
DISC MENU:
¡Sets the language for DVD menu.
5 Press the Arrow buttons (K/ L) to select a
setting, then press the ENTER button.
¡If OTHER is selected on the AUDIO, SUBTITLE or
DISC MENU screen, press four-digit number to
enter the code for the desired language. (Refer to the
language code list below.)
¡Only the languages supported by the disc can be
selected.
6 Press the SETUP button to exit.
NOTE
¡Language Setting for Audio and Subtitle is not available with some discs. Then use the AUDIO and the
SUBTITLE buttons. Details are on page 42.
TO CHANGE THE ON-SCREEN MENUS
Language
Code Language
A-B
Abkhazian
Afar
Afrikaans
Albanian
Amharic
Arabic
Armenian
Assamese
Aymara
Azerbaijani
Bashkir
Basque
Bengali;Bangla
Bhutani
Bihari
Bislama
Breton
Bulgarian
Burmese
Byelorussian
C-E
Cambodian
Catalan
Chinese [CHI]
Corsican
Croatian
Czech
Danish [DAN]
Dutch [DUT]
English [ENG]
Esperanto
Estonian
F-H
Faroese
Fiji
Finnish [FIN]
French [FRE]
Frisian
Galician
Georgian
German [GER]
Greek [GRE]
Greenlandic
Guarani
Gujarati
Hausa
Hebrew
Hindi
Hungarian [HUN]
I-K
Icelandic [ICE]
Indonesian
Interlingua
Interlingue
Inupiak
Irish [IRI]
Italian [ITA]
Japanese [JPN]
Javanese
Kannada
Kashmiri
Kazakh
Kinyarwanda
Kirghiz
Kirundi
Korean [KOR]
Kurdish
Code
L-N
4748
4747
4752
6563
4759
4764
5471
4765
4771
4772
4847
5167
4860
5072
4854
4855
4864
4853
5971
4851
5759
4947
7254
4961
5464
4965
5047
6058
5160
5161
5166
5261
5256
5255
5264
5271
5358
5747
5051
5158
5758
5360
5367
5447
5569
5455
5467
5565
5560
5547
5551
5557
5347
5566
5647
5669
5760
5765
5757
6469
5771
6460
5761
5767
Laothian
Latin
Latvian;Lettish
Lingala
Lithuanian
Macedonian
Malagasy
Malay
Malayalam
Maltese
Maori
Marathi
Moldavian
Mongolian
Nauru
Nepali
Norwegian [NOR]
O-R
Occitan
Oriya
Oromo(Afan)
Panjabi
Pashto;Pushto
Persian
Polish
Portuguese [POR]
Quechua
Rhaeto-Romance
Romanian [RUM]
Russian [RUS]
S
Samoan
Sangho
Sanskrit
Scots Gaelic
Serbian
Serbo-Croatian
Sesotho
Setswana
Shona
Sindhi
Singhalese
Siswat
Slovak
Slovenian
Somali
Spanish [SPA]
Sundanese
Swahili
Swedish [SWE]
T
Tagalog
Tajik
Tamil
Tatar
Telugu
Thai
Tibetan
Tigrinya
Tonga
Tsonga
Turkish [TUR]
Turkmen
Twi
U-Z
Ukrainian
Urdu
Uzbek
Vietnamese
Volapuk
Welsh
Wolof
Xhosa
Yiddish
Yoruba
Zulu
5861
5847
5868
5860
5866
5957
5953
5965
5958
5966
5955
5964
5961
5960
6047
6051
6061
6149
6164
6159
6247
6265
5247
6258
6266
6367
6459
6461
6467
6559
6553
6547
5350
6564
6554
6566
6660
6560
6550
6555
6565
6557
6558
6561
5165
6567
6569
6568
6658
6653
6647
6666
6651
6654
4861
6655
6661
6665
6664
6657
6669
6757
6764
6772
6855
6861
4971
6961
7054
5655
7161
7267
You can access the TV/VCR SETUP menu by pressing
the SETUP button from the DVD mode. Refer to
“Selecting the Language” on page 16 to changing the
If you choose a Language that has a 3 letter language
on-screen menus.
code, the code will be displayed every time you change
¡In case of selecting from the DVD mode, you cannot
the Audio or Subtitle language setting on page 42. If
select “CHANNEL SET UP”, “V-CHIP SET UP”,
you choose any other languages, ‘---’ will be displayed
“CAPTION”, “TIME SEARCH”, or “INDEX
instead. (3 letter language code is written in bracket.)
SEARCH” menus.
EN
– 44 –
01A11
TD851/951(P36-52).QX33
03.3.1 1:56 PM
Page 45
DISPLAY SETTING
AUDIO SETTINGS
DVD-V
You can change certain aspects of the DVD display
screens and on-screen messages on the TV screen.
1 Press the SETUP button twice in STOP mode
so that the DVD SETUP menu appears.
¡ If the menu does not appear, press the PLAY button,
Choose the appropriate Audio settings for your equipment as it only affect during the playback of DVD
discs.
1 Press the SETUP button twice in STOP mode
so that the DVD SETUP menu appears.
¡ If the menu does not appear, press the PLAY button,
the STOP button, then the SETUP button twice.
the STOP button, then the SETUP button twice.
QUICK SETUP
TV MODE
DOLBY DIGITAL
QUICK SETUP
TV MODE
DOLBY DIGITAL
4:3 LETTER BOX
ON
4:3 LETTER BOX
ON
2 Press the Arrow button B to select CUSTOM, then press the ENTER button.
¡CUSTOM mode will appear.
2 Press the Arrow button B to select CUSTOM, then press the ENTER button.
¡CUSTOM mode will appear.
3 Press the Arrow buttons (s/ B) to select
AUDIO, then press the ENTER button to
confirm.
3 Press the Arrow button (s/ B) to select DISPLAY, then press the ENTER button to confirm.
AUDIO
DRC
OFF
DOLBY DIGITAL
ON
DOWN SAMPLING ON
DISPLAY
4:3 LETTER BOX
TV MODE
ANGLE ICON
ON
AUTO POWER OFF ON
4 Press the Arrow buttons (K/ L) to select the
below items, then press the ENTER buttons.
4 Press the Arrow buttons (K/ L) to select the
below items, then press the ENTER button.
TV MODE: QUICK
¡Press the Arrow buttons (K/L) for an item selection,
then press the ENTER button.
¡Select 4:3 LETTER BOX for a black bars appears
on top and bottom of the screen.
¡Select 4:3 PAN & SCAN for a full height picture
with both sides trimmed.
¡The default setting is 4:3 LETTER BOX.
ANGLE ICON:
¡Press the ENTER button repeatedly to turn Angle
icon ON or OFF.
¡The default setting is ON.
AUTO POWER OFF:
¡Press the ENTER button repeatedly to turn Auto
Power off ON or OFF.
¡The default setting is ON and it will turn the
TV/DVD/VCR to off automatically after 15 minutes
of no use.
DRC (Dynamic Range Control):
¡To compress the range of soft to loud sound.
¡The default setting is OFF.
DOLBY DIGITAL: QUICK
Set to On when the unit is connected to a Dolby Digital
Decoder.
(ON: Output a Dolby Digital signal)
(OFF: Convert the Dolby Digital to PCM (2 channel
stereo))
¡The default setting is ON.
DOWN SAMPLING:
¡Set to ON when outputting in 48 kHz.
¡The default setting is ON.
When playing disc with copyright Protection
¡If you select OFF, copyright protection will be activated and sound will be down sampled at 48kHz.
5 Press the SETUP button to exit.
5 Press the SETUP button to exit.
– 45 –
EN
01A11
TD851/951(P36-52).QX33
03.3.1 1:56 PM
Page 46
PARENTAL CONTROL
DVD-V
CONTROL LEVELS
¡ALL
Parental Control limits the disc viewing that exceed
your settings. (with a password or playback will stop.)
This feature allows you to prevent discs with alternative scenes from being played by your children.
All parental lock is cancelled.
¡Level 8
DVD software of any grade (adult/general/children)
can be played back.
¡Levels 7 to 2
PARENTAL LEVEL
Parental Level allows you to set the rating level of
your DVD discs. Playback will stop if the disc’s ratings exceed the level you set.
Only DVD software intended for general use and
children can be played back.
¡Level 1
Only DVD software intended for children can be
played back, with those intended for adult and
general use prohibited.
1 Press the SETUP button twice in STOP mode
so that the QUICK SETUP menu appears.
¡ If the menu does not appear, press the PLAY button,
the STOP button, then the SETUP button twice.
IF YOU FORGET THE PASSWORD
1 Press the number buttons 4, 7, 3, 7 at step 4.
QUICK SETUP
TV MODE
DOLBY DIGITAL
4:3 LETTER BOX
ON
Then enter your new password.
¡Password will be cleared and parental level will be
set to ALL.
2 Press the Arrow button B to select CUSTOM, then press the ENTER button.
2 Proceed the above Steps 5-7 again.
3 Press the Arrow buttons (s/B) to select
PARENTAL, then press the ENTER button.
PARENTAL
PARENTAL LEVEL ALL
4 Enter your four-digit password then press
the ENTER button.
5 Press the Arrow buttons (K/ L) to select
PARENTAL LEVEL, then press the ENTER
button.
6 Press the Arrow buttons (K/ L) to select
the desired level.
7 Press the SETUP button to exit
NOTES
¡When doing this for the first time, enter any 4 digits.
(except for 4737) That number will be used as the
password.(in the event you forget the password, see
below)
¡To change the password, press the Arrow buttons
(K/L) to select CHANGE at step 5, then press the
ENTER button. Enter the four-digit pass-word, then
press the ENTER button.
¡With some DVDs, it may be difficult to find if they
are compatible with parental lock. Be sure to check
if the parental lock function operates in the way that
you have set.
¡Record the password in case you forget it.
– 46 –
EN
01A11
TD851/951(P36-52).QX33
03.3.1 1:56 PM
Page 47
TROUBLESHOOTING GUIDE
If the TV/DVD/VCR does not perform properly when operated as instructed in this Owner’s Manual, check
the player, consulting the following checklist.
PROBLEM
No power.
The TV/DVD/VCR does not
respond to the remote control.
CORRECTIVE ACTION
• Make sure the power plug is connected to an AC outlet.
• Make sure the power is turned on.
• Check if the power plug is connected to an AC outlet.
• Check the batteries in the remote control.
• Aim the remote control directly at the remote sensor. If necessary,
remove all the obstacles between the sensor and the remote.
• You have to be within 23 feet of the TV/DVD/VCR.
• Check if the correct mode is selected. If not switch the mode by
pressing the SELECT button on the remote control,whichever you need.
TV/VCR Mode
Sometimes a performance problem can be easily solved by checking seemingly apparent but often overlooked
possibilities. Before arranging for service, check these items. It could save your time and money.
PROBLEM
CORRECTIVE ACTION
No picture and sound.
• Make sure the AC cord is connected to an AC outlet.
• Check antenna connection.
• Press the SELECT button on the remote control to select TV mode.
Then try other TV feature.
• Let the TV/DVD/VCR program its tuner memory.
No picture or poor picture on
• Adjust direction or replace antenna.
TV/DVD/VCR.
• Adjust picture controls.
No sound or poor sound.
• Adjust volume control on remote control or main unit.
• Press the MUTE button to restore sound.
Bars On Screen
• If outside antenna is being used, check for broken wire.
• Check for local interference.
Picture Distorted or Blurred
• Try a new channel, if OK, then possible station trouble.
• If outside antenna is being used, check for broken wire.
Picture Rolls Vertically
• Try a new channel, if OK, then possible station trouble.
Lines or Streaks in Picture
• If outside antenna is being used, check for broken wire.
• Check for local interference.
No Color
• Try a new channel, if OK, then possible station trouble.
• Is antenna connected to terminal on the back of the set?
• If outside antenna is being used, check for broken wire.
• Adjust COLOR control.
Poor Reception on Some Channels • Try a new channel, if OK, then possible station trouble.
Ghosts in Picture
• Is antenna connected to terminal on the back of the set?
• If outside antenna is being used, check for broken wire.
• Check for local interference.
Weak Picture
• Try a new channel, if OK, then possible station trouble.
• Is antenna connected to terminal on the back of the set?
• If outside antenna is being used, check for broken wire.
• Adjust CONTRAST & BRIGHT control.
Sound OK, Picture Poor
• Try a new channel, if OK, then possible station trouble.
• Is antenna connected to terminal on the back of the set?
• If outside antenna is being used, check for broken wire.
• Check for local interference.
• Adjust CONTRAST & BRIGHT control.
– 47 –
EN
01A11
TD851/951(P36-52).QX33
03.3.1 1:56 PM
PROBLEM
Picture OK, Sound Poor
Page 48
No picture but the audio is OK in
playback.
CORRECTIVE ACTION
Try
a
new
channel,
if OK, then possible station trouble.
•
Check
for
local
interference.
•
• Make sure the timer recording is set correctly.
• Make sure the power is off.
• Make sure the TV/DVD/VCR clock is set correctly.
• Make sure the tape has an erase-prevention tab. If need, cover the
• hole with plastic tape.
• Adjust tracking control for a better picture using the CHANNEL
• button K or L on the TV/DVD/VCR.
• Head cleaning may be necessary. Refer to “AUTO HEAD
• CLEANING” on page 50.
No operation by infrared Remote
Control.
Video or color fades in and out
when making a copy of a video tape.
Different color marks on screen.
• Make sure the AC cord is connected to an AC outlet.
• Check batteries in remote control.
• You can not copy a copyrighted video tape. You are experiencing
• copy guard protection.
• Magnetism from nearby appliances and geomagnetism might affect
Timer recording is not possible.
Cannot go into Record mode.
Playback picture is partially noisy.
the color of the TV picture. Move the TV/DVD/VCR away from the
appliances, the TV/DVD/VCR can repair itself automatically. If you
want to repair immediately, turn off using the POWER button, then
turn it on again 30 minutes or so later (27” model), or unplug the
power cord, then plug it in again 30 minutes or so later (19” model).
CLOSED CAPTION PROBLEM
POSSIBLE REMEDY
My TV/DVD/VCR is showing
• You are watching a live broadcast and spelling errors made by the
captions that are misspelled.
• closed captioning production company may pass through uncorrected.
• A prerecorded program will not show any misspelled words because
• of the normal time available for editing the captions.
My TV/DVD/VCR will not show
• Captions that are delayed a few seconds behind the actual
the text dialogue
are common for live broadcast. Most captioning production
in its entirety or there is a delay of • companies can display a dialogue to a maximum of 220 words
what is being said.
• per minute. If a dialogue exceeds that rate, selective editing is used
• to insure that the captions remain up-to-date with the current
• TV screen dialogue.
My captions are scrambled with
• Interference caused by building, power lines, thunderstorms, etc.
white boxes on the TV screen.
• may cause scrambled or incomplete captions to appear.
My program guide listed a TV show • Broadcasters may at times use a time compression process to speed
as being closed captioned but none • up the actual program so that additional advertising time can be
of the captions were displayed.
• given. Since the decoder cannot read the compressed information,
• captions will be lost.
My prerecorded video tape does not • The video tape was either an illegal copy or the tape duplicating
show any captions. The tape box
• company accidentally left out the captioning signals during the
mentions it being closed captioned. • copying process.
My TV screen shows a black box
• You are in the TEXT mode. Select CAPTION mode to CAPTION
on certain channels.
• [OFF].
– 48 –
EN
01A11
TD851/951(P36-52).QX33
03.3.1 1:56 PM
Page 49
DVD Mode
PROBLEM
No picture.
CORRECTIVE ACTION
• Connect the video cables firmly.
• Insert a correct video disc that plays on this TV/DVD/VCR.
• Press the SELECT button on the remote control to select DVD mode.
Then, try other DVD feature.
• Insert the disc.
Disc cannot be played.
• Clean the disc.
• Place the disc correctly, with the label side up.
• Cancel the parental lock or change the control level.
• Connect the audio cables firmly.
No sound.
• Turn the power of the audio component on.
• Correct the audio output settings.
• Correct the input settings on the audio component.
• This TV/DVD/VCR does not support DTS audio. This is not a malNo DTS audio is output.
function.
• There are some cases where pictures may be slightly distorted, which
Distorted picture.
are not a sign of a malfunction.
• Although pictures may stop for a moment, this is not a malfunction.
Audio or subtitle language
• The selected language is not available for audio or subtitles on the DVD.
does not match the set up
This is not a malfunction
The camera angle cannot be changed • The DVD does not contain sequences recorded from different camera
angles. This is not a malfunction
Audio or subtitle language cannot be • The DVD does not contain audio source or subtitles in the selected
changed
language. This is not a malfunction.
“Prohibited icon” appears on the
• That operation is prohibited by the player or the disc.
screen, prohibiting an operation
This is not a malfunction.
CD sound dropout
• Scratched disc. Replace the disc with unscratched one.
No CD reproduction
DVD picture dropout
DVD picture freeze
DVD picture in mosaic
No DVD reproduction
NOTES:
• Some functions are not available in specific modes, but this is not a malfunction. Read the description in
this Owner’s Manual for details on correct operations.
• Playback from a desired track and random playback are not available during program playback.
– 49 –
EN
01A11
TD851/951(P36-52).QX33
03.3.1 1:56 PM
Page 50
MAINTENANCE
CABINET CLEANING
• Wipe the front panel and other exterior surfaces of
•
the TV/DVD/VCR with a soft cloth immersed in
lukewarm water and wrung dry.
Never use a solvent or alcohol. Do not spray insecticide liquid near the TV/DVD/VCR. Such chemicals may cause damage and discoloration to the
exposed surfaces.
1.Please visit your local Audio/Video store and purchase a good quality VHS Video Head Cleaner.
2.If a Video Head Cleaner does not solve the problem, please call our help line at 1-800-968-3429, to
locate an Authorized Service Center.
NOTES:
• Remember to read the instructions included with
the video head cleaner before use.
• Clean video heads only when problems occur.
AUTO HEAD CLEANING
SERVICING
• Automatically cleans video heads as you insert or
•
remove a cassette, so you can see a clear picture.
Playback picture may become blurred of interrupted while the TV program reception is clear. Dirt
accumulated on the video heads after long periods
of use, or the usage of rental or worn tapes can
cause this problem.
If a streaky or snowy picture appears during playback, the video heads in your TV/DVD/VCR may
need to be cleaned.
• Should your TV/DVD/VCR become inoperative,
do not try to correct the problem by yourself. There
are no user-serviceable parts inside. Turn off,
unplug the power cord, and please call our help
line at 1-800-968-3429, to locate an Authorized
Service Center.
IF THE LASER OPTICAL PICKUP UNIT IS DIRTY
• If the player still does not perform properly when it is operated while referring to the relevant sections and to
"TROUBLESHOOTING GUIDE" in this Owner's Manual, the laser optical pickup unit may be dirty. Consult
your dealer or an Authorized Service Center for inspection and cleaning of the laser optical pickup unit.
DISC HANDLING
• Use discs which have the following logos on them.
(Optical audio digital discs.)
Recordable
ReWritable
• Handle the discs so that fingerprints and dust do
• To clean-off, use a soft cloth.
• Do not use a hard cloth since this will mar the disc.
• Wipe the disc in a straight line from center to edge.
• Never wipe with a circular motion.
• Do not use detergent or abrasive cleaning agents.
not adhere to the surfaces of the discs.
• Always store the disc in its protective case when it
is not used.
– 50 –
EN
01A11
TD851/951(P36-52).QX33
03.3.1 1:56 PM
Page 51
SPECIFICATIONS
GENERAL SPECIFICATIONS
Sound output:
TV/VCR
CRT
[19 inch model]:
19 inch in-line gun, 90˚
deflection tube
[27 inch model]:
27 inch in-line gun, 110˚
deflection tube
Television system :
NTSC-M
Closed caption system :§15.119/FCC
Video Heads :
Rotary four-head
Tape width :
1/2 inch
Tape speed
SP :
33.40mm/sec.
LP :
16.67mm/sec.
SLP :
11.12mm/sec.
Tuner channel
TV VHF Low :
#2~#6
TV VHF High :
#7~#13
TV UHF :
#14~#69
CATV
VHF :
5A
MID band :
A5~A1, A~I
SUPER band :
J~W
HYPER band :
W+1~W+84
DVD
Product type:
Discs:
Output signal format:
Frequency response
(out put jack)
DVD (linear sound):
ELECTRICAL SPECIFICATIONS
DVD Player
DVD video, Audio CD
NTSC color
20 Hz to 22 kHz
(sample rate: 48 kHz)
20 Hz to 44 kHz
(sample rate: 96 kHz)
20 Hz to 20 kHz
CD:
Signal-to-noise ratio
(S/N ratio)(out put jack)
CD:
75 dB (EIAJ)
Dynamic range
(out put jack)
DVD (linear sound): 85 dB
CD:
84 dB (EIAJ)
Total distortion factor
CD:
0.07% (EIAJ)
Wow and flutter:
Below the measurement
limitation (+/-0.001%
W PEAK) (EIAJ)
2 speakers, 1W, 8 ohm
OTHER SPECIFICATIONS
Terminals
Antenna input:
Video input:
Audio L/R input:
Headphone:
Coaxial digital
audio output:
Analog audio L/R
output :
Remote control:
Operating
temperature:
Power requirements:
[19 inch model]
Power consumption
(Maximum):
Picture tube:
Dimensions:
Weight:
[27 inch model]
Power consumption
(Maximum):
Picture tube:
Dimensions:
Weight:
VHF/UHF/CATV
75 ohm unbalanced (F-type)
RCA connector [ 1
RCA connector [ 2
1/8” stereo (3.5 mm)
One pin jack,
500m Vpp (75 ohm)
RCA connector [ 2
Digital encoded
infrared light system
5ºC to 40ºC
(41ºF~104ºF)
AC 120V, 60Hz
90W
19"
H:19-11/16” (500mm)
W:21-7/8” (556mm)
D:18-3/4” (476.5mm)
45.2 lbs (20.5kg)
125W
27"
H:25-1/2” (648mm)
W:26-9/16” (675mm)
D:19-11/16” (500mm)
86 lbs (39.0kg)
• Designs and specifications are subject to change without notice.
• If there is a discrepancy between languages, the default language will be English.
– 51 –
EN
01A11
TD851/951ES.QX33
03.3.1 1:57 PM
Page 52
INDICE
■ CONTROLES DE OPERACIÓN Y FUNCIONES . . . . . 52
PANEL FRONTAL DEL TELEVISOR/DVD. . . . . . . . . . 52
MANDO A DISTANCIA . . . . . . . . . . . . . . . . . . . . . . . . . 52
VISTA POSTERIOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
■ PREPARACIÓN PARA LA UTILIZACIÓN . . . . . . . . . . 53
CONEXIONES DE ANTENA/CABLE . . . . . . . . . . . . . . 53
CONEXIÓN A TOMAS DE ENTRADA EXTERNA. . . . 53
PARA INSERTAR LAS PILAS . . . . . . . . . . . . . . . . . . . . 54
MODO DE ENTRADA EXTERNA . . . . . . . . . . . . . . . . 54
CONEXIÓN A UN SISTEMA ESTÉREO . . . . . . . . . . . . 54
CONEXIÓN A UN AMPLIFICADOR ESTÉREO
EQUIPADO CON TOMAS DE ENTRADA DIGITAL,
PLATINA MD O PLATINA DAT (Para DVD). . . . . . . . . 54
CONEXIÓN A UN DECODIFICADOR DOLBY DIGITAL
(para DVD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
SECCIÓN DE TV/VCR
■ PREPARACIÓN PARA LA UTILIZACIÓN . . . . . . . . . . 54
PREAJUSTE DE CANALES. . . . . . . . . . . . . . . . . . . . . . 55
CÓMO BORRAR (AGREGAR) CANALES . . . . . . . . . . 55
SECCIÓN DE DVD
REPRODUCCIÓN BÁSICA . . . . . . . . . . . . . . . . . . . . . . 55
CONTROLES DE
OPERACIÓN Y FUNCIONES
PANEL FRONTAL DEL
TELEVISOR/DVD
Consulte la figura 1 de la página 9
MANDO A DISTANCIA
Consulte la figura 2 de la página 9
VISTA POSTERIOR
Consulte la figura 3 de la página 10
1. Botón POWER
Presione este botón para conectar y desconectar la alimentación.
2. Botones VOLUME X/Y
Presione estos botones para controlar el nivel de volumen
del DVD y el televisor.
3. Botones SKIP (para DVD)
Presione el botón correspondiente una vez para omitir
capítulos o pistas y desplazarse a un punto específico.
Mantenga el botón presionado para cambiar la velocidad de reproducción en avance o retroceso.
4. Botón PLAY
Inicia la reproducción del contenido del disco o cinta.
5. Botón STOP
Detiene la reproducción del disco.
6. Botón OPEN/CLOSE
Presione este botón para insertar discos en la bandeja o
retirarlos de ella.
7. Bandeja de carga del disco
8. Indicador DVD
Se ilumina durante el modo DVD.
9. Botón SELECT
Presione este botón para cambiar al modo TV/VCR,
modo de entrada externa o modo de DVD.
10. Indicador TV/VCR
Se ilumina durante el modo TV/VCR.
11. Botones CHANNEL K/L
Utilice estos botones para seleccionar canales memorizados.
12. Indicador de grabación
Parpadea durante la grabación. Se ilumina durante el
modo de espera de grabación controlada por temporizador.
13. Botón REC/OTR (RECORD)
Presione este botón para grabar manualmente. Este
botón también activa la función de grabación instantánea (OTR). (La función OTR sólo está disponible
durante el modo TV/VCR.)
14. Botón REW (para TV/VCR)
Presione este botón para rebobinar la cinta o para ver
la imagen rápidamente en dirección de retroceso
durante el modo de reproducción. (Búsqueda en dirección de retroceso)
15. Botón FWD (para TV/VCR)
Presione este botón para adelantar rápidamente la cinta
o para ver la imagen rápidamente en dirección de
avance durante el modo de reproducción. (Búsqueda en
dirección de avance)
16. Botón STOP/EJECT
Presione este botón para detener la cinta. Presiónelo en
el modo de parada para retirar la cinta del
televisor/DVD/videograbadora.
17. Ventanilla del sensor de mando a distancia
18. Toma HEADPHONE
Para conectar auriculares (no suministrados) y escuchar
en privado.
19. Toma de entrada VIDEO
Conecte aquí la toma de salida de vídeo de una
videocámara o de una videograbadora.
20. Tomas de entrada AUDIO L/R
Conecte aquí las tomas de salida de audio de una
videocámara o de una videograbadora.
21. Compartimiento del cassette
22. Botón PICTURE
Presione este botón para ajustar la imagen.
23. Botones numéricos
Modo TV:
Presione dos botones para acceder directamente al
canal deseado.
No olvide presionar “0” antes de elegir un canal de un
solo dígito.
Botón +100
Presione este botón para seleccionar canales de televisión por cable cuyo número sea igual o superior a 100.
Modo DVD:
Presione este botón para introducir el número deseado.
Botón +10
Presione este botón para introducir números iguales o
mayores que 10.
24. Botón PAUSE
Hace una pausa en la reproducción del disco o cinta.
25. Botón SPEED
Presione este botón para seleccionar la velocidad de
grabación deseada: SP/SLP.
26. Botón C.RESET
Presione este botón para poner el contador en 0:00:00.
Presiónelo también para cancelar un ajuste de programa de temporizador.
27. Botón DISPLAY
Modo TV/VCR:
Para visualizar el contador o el número del canal y la
fecha actual en la pantalla del televisor.
Modo DVD:
Indica el estado actual en la pantalla del televisor para
fines de comprobación.
28. Botón SETUP
Presione este botón para activar o salir del modo de
menús de televisor o configuración de DVD.
29. Botón TITLE
Para visualizar el menú de títulos.
– 52 –
ES
0C28
TD851/951ES.QX33
03.3.1 1:57 PM
Page 53
30. Botón CLEAR
Para cancelar ajustes.
31. Botón MODE
Activa el modo de reproducción programada o el modo de
reproducción aleatoria.
32. Botón SEARCH MODE
Presione este botón para localizar un punto deseado.
33. Botón AUDIO
Presione este botón para seleccionar un idioma de
audio o el modo de sonido deseado.
34. Botón SUBTITLE
Presione este botón para seleccionar el idioma de subtítulos deseado.
35. Botón REPEAT
Repite la reproducción del disco, título, capítulo o pista actual.
36. Botón ANGLE (modo DVD)
Presione este botón para cambiar el ángulo de la cámara
y ver la secuencia que se está reproduciendo desde un
ángulo diferente.
37. Botón A-B REPEAT
Repite la reproducción de una sección seleccionada.
38. Botón RETURN
Permite volver a la operación anterior en el modo de
configuración de DVD.
39. Botón ENTER
Presione este botón para establecer un ajuste.
40. Botones de flechas
Modo TV/VCR:
Presione estos botones para seleccionar un modo de
ajuste en el menú que aparece en la pantalla del televisor.
Presiónelos también para seleccionar opciones o
establecer ajustes en un menú en particular.
Modo DVD:
Use estos botones para hacer ajustes mientras observa
la imagen en la pantalla del televisor.
41. Botón DISC MENU
Muestra los menús contenidos en el DVD.
42. Botón ZOOM
Amplía parte de la imagen reproducida de un DVD.
43. Botón MUTE
Suprime la salida de sonido. Presiónelo de nuevo para
restablecer el sonido.
44. Botón SLEEP
Utilice este botón para ajustar el temporizador de dormir.
45. Botón SELECT
Presione este botón para cambiar entre los modos
TV/VCR y DVD. El modo seleccionado (TV/VCR o
DVD) se visualiza en el indicador del panel delantero.
46. Toma de entrada ANT.
Conéctela a una antena, sistema de televisión por cable
o sistema de satélite.
47. Cable de alimentación
Conéctelo a una toma de CA estándar (120 V, /60 Hz).
NOTA: Antes de conectar el cable de alimentación a
una toma de CA estándar, retírelo del gancho
para evitar dañarlo.
48. Toma de salida de audio digital COAXIAL
Conéctela solamente a la entrada digital de un amplificador externo o decodificador de audio de DVD.
49. Toma de salida AUDIO L/R
Conéctela a la entrada de audio analógico de un amplificador o decodificador externo.
PREPARACIÓN PARA LA
UTILIZACIÓN
CONEXIONES DE ANTENA/CABLE
ANTENAS SEPARADAS DE VHF/UHF
En algunas zonas será necesario utilizar una antena
exterior.
TELEVISIÓN POR CABLE SIN CAJA DE
CONVERTIDOR/DECODIFICADOR
Utilice esta conexión si su sistema de televisión por
cable se conecta directamente a su televisor/DVD/
videograbadora, sin una caja de convertidor.
Con esta conexión podrá:
1) Utilizar el mando a distancia del televisor/DVD/
videograbadora para seleccionar canales.
2) Programar uno o más canales decodificados para
grabación automática controlada por temporizador.
NOTA: Este televisor/DVD/videograbadora SÓLO
puede grabar el canal que se está viendo.
TELEVISIÓN POR CABLE CON CAJA
DE CONVERTIDOR/DECODIFICADOR
O CAJA DE SATÉLITE
Si su compañía de televisión por cable le suministra
una caja de convertidor o si utiliza un sistema de
satélite, podrá utilizar la conexión básica que se
muestra en la ilustración.
Al utilizar esta conexión, también podrá grabar canales
codificados. Sin embargo, la selección de los canales
deberá hacerse con la caja de convertidor o con la caja
de satélite. Esto significa que no es posible cambiar de
canal utilizando el mando a distancia del televisor/DVD/
videograbadora. La grabación en ausencia (controlada
por temporizador) está limitada a un canal a la vez.
PARA GRABAR UN CANAL
CODIFICADO/DECODIFICADO
1.Ajuste el selector de canales del
televisor/DVD/videograbadora al canal de salida de
la caja de convertidor de televisión por cable o caja
de satélite. (Ej., CH3)
2.Seleccione el canal que desea grabar en la caja de
convertidor de televisión por cable o caja de satélite.
Nota para el instalador de sistemas CATV
Esta nota tiene la finalidad de llamar la atención
del instalador de sistemas CATV para que tenga
en cuenta el Artículo 820-40 de la NEC, que proporciona recomendaciones para hacer una conexión a tierra apropiada y, en particular, especifica
que la tierra del cable debe conectarse al sistema
de puesta a tierra del edificio, tan cerca del punto
de entrada del cable como sea posible.
CONEXIÓN A TOMAS DE
ENTRADA EXTERNA
Cuando vea un programa grabado en otra fuente (videograbadora o videocámara), utilice las tomas de entrada de audio/vídeo
de la parte delantera del televisor/DVD/videograbadora.
Conecte las tomas de salida de audio/vídeo de otra fuente a
las tomas AUDIO L/R y VIDEO de este
televisor/DVD/videograbadora. Luego, presione los botones
CHANNEL K/L hasta que aparezca "AUX" en la pantalla.
NOTA:
• Cuando conecte una videograbadora monofónica (otra
fuente) a este televisor/DVD/videograbadora, conecte la
toma de salida de audio de la videograbadora monofónica
(otra fuente) a la toma AUDIO L de este
televisor/DVD/videograbadora. El audio saldrá igualmente por los canales izquierdo y derecho.
Consulte la figura 4 de la página 11
– 53 –
Consulte la figura 5 de la página 12
ES
0C28
TD851/951ES.QX33
03.3.1 1:57 PM
Page 54
PARA INSERTAR LAS PILAS
1) Abra la cubierta del compartimiento de las pilas
empujando la cubierta del mando a distancia en el
sentido de la flecha.
2) Inserte 2 pilas "AA" en el compartimiento de las
pilas, en el sentido indicado por las marcas de
polaridad (+/-).
3) Vuelva a poner la cubierta.
MODO DE ENTRADA EXTERNA
Al usar una señal de entrada externa (otra videograbadora o una videocámara), conecte los cables de salida de
audio/vídeo del equipo externo a las tomas AUDIO L/R
IN/ VIDEO IN de su televisor/DVD/videograbadora.
Luego, presione los botones CHANNEL K/L hasta que
aparezca "AUX" en la pantalla.
CONEXIÓN A UN SISTEMA
ESTÉREO
NOTAS:
• Asegúrese de desconectar la alimentación de todos
los componentes del sistema antes de conectar otro
componente.
• Consulte el manual de instrucciones de su sistema
estéreo y de cualquier otro componente que vaya a
conectar al televisor/DVD/videograbadora.
Consulte la figura 6 de la página 13
CONEXIÓN A UN AMPLIFICADOR
ESTÉREO EQUIPADO CON TOMAS
DE ENTRADA DIGITAL, PLATINA
MD O PLATINA DAT (Para DVD)
CONEXIÓN A UN DECODIFICADOR
DOLBY DIGITAL (para DVD)
Si utiliza este televisor/DVD/videograbadora para
reproducir un disco DVD grabado en formato de
sonido envolvente Dolby Digital de 5,1 canales, el
televisor/DVD/videograbadora emitirá un flujo de
datos DOLBY DIGITAL desde su toma de salida de
audio digital COAXIAL. Si conecta el reproductor a
un decodificador Dolby Digital, podrá disfrutar de
una tonalidad más convincente y real, con un sonido
envolvente potente y de alta calidad similar al de los
cines.
Utilice cables digitales coaxiales de audio
disponibles en el comercio especializado para hacer
las conexiones de audio.
Consulte la figura 8 de la página 14
NOTAS:
• Asegúrese de desconectar la alimentación de todos
los componentes del sistema antes de conectar otro
componente.
• Consulte los manuales de instrucciones de los
componentes que va a conectar al
televisor/DVD/videograbadora.
• Si conecta un decodificador Dolby Digital, ajuste
la función DOLBY DIGITAL a ON para salida de
audio en el modo de configuración.
• A menos que se haga la conexión a un decodificador Dolby Digital, ajuste la función Dolby
Digital a OFF para salida de audio en el modo de
configuración. La reproducción en un
televisor/DVD/videograbadora utilizando ajustes
incorrectos puede generar ruido y distorsión, y
también puede causar daños a los altavoces.
Fabricado bajo licencia de Dolby
Laboratories. “Dolby” y el símbolo de la D
doble son marcas de fábrica de Dolby
Laboratories.
Utilice un cable digital coaxial de audio de venta en el
comercio especializado para hacer las conexiones de audio.
Conexión a un amplificador equipado con tomas de
entrada digital, platina MD o platina DAT.
SECCIÓN DE TV/VCR
PREPARACIÓN PARA LA
UTILIZACIÓN
Consulte la figura 7 de la página 13
NOTAS:
• La fuente de audio de un disco grabado en formato
de sonido envolvente Dolby Digital de 5,1 canales
no se puede grabar como sonido digital mediante
una platina MD o DAT.
• Asegúrese de desconectar la alimentación de todos
los componentes del sistema antes de conectar otro
componente.
• Consulte los manuales de instrucciones de los
componentes que va a conectar al
televisor/DVD/videograbadora.
• Ajuste la función Dolby Digital a OFF para salida
de audio en el modo de configuración. La reproducción en un televisor/DVD/videograbadora utilizando ajustes incorrectos puede generar ruido y
distorsión, y también puede causar daños a los
altavoces.
Puede programar el sintonizador para explorar todos
los canales que pueda recibir en su zona.
NOTA: La programación de la memoria de canales
NO es necesaria cuando se hace la conexión a una
caja de televisión por cable o a una caja de satélite.
Simplemente ajuste el selector de canales del televisor/DVD/videograbadora a la posición correspondiente al canal de salida de la caja de televisión por
cable o caja de satélite (ej., CH3). Luego, seleccione
el canal que desea ver en la caja de televisión por
cable o en la caja de satélite.
– 54 –
ES
0C28
TD851/951ES.QX33
03.3.1 1:57 PM
Page 55
PREAJUSTE DE CANALES
2
TV/VCR
1
Conecte el cable de alimentación del televisor/DVD/videograbadora
3
Conecte el cable de alimentación del
televisor/DVD/videograbadora
NOTA:
• Si aparecen algunos dígitos en la esquina de la pantalla, presione el botón POWER sin desconectar el
cable de alimentación.
2
Seleccione “ENGLISH”, “ESPAÑOL” o
“FRANÇAIS”
Presione el botón ENTER para seleccionar "ENGLISH" = inglés, "ESPAÑOL" o "FRANÇAIS" =
francés. "[ ]" indica el idioma seleccionado.
4
Inicie el preajuste automático
Presione el botón de flecha K o L para señalar
"AUTOPRESELECCION".
Luego, presione el botón ENTER.
El sintonizador explora y memoriza todos los canales
activos de su zona.
NOTAS:
• El televisor/DVD/videograbadora distingue entre
los canales de TV estándar y los canales de televisión por cable.
• Si desea reproducir o grabar una cinta de vídeo
ANTES de preajustar el sintonizador, deberá presionar el botón SETUP del mando a distancia.
• El televisor/DVD/videograbadora puede memorizar
canales de TV como canales de CATV si las condiciones de recepción no son buenas. Si esto sucede,
vuelva a intentar la acción AUTO MEMO cuando
las condiciones de recepción mejoren.
5
4
Borre el canal de la memoria o agréguelo a
ella
• Para borrar otro canal, repita los pasos [3] y [4].
• Si vuelve a presionar el botón ENTER, el canal se
memorizará de nuevo.
• Presione el botón RETURN para hacer que el televisor/videograbadora vuelva al menú SETUP.
5
Salga del modo de preajuste de canales
Presione el botón SETUP del mando a distancia para
volver al modo de televisor.
NOTA: Para confirmar que los canales han sido borrados o agregados, presione el botón CHANNEL K o
L.
SECCIÓN DE DVD
REPRODUCCIÓN BÁSICA
DVD-V
CD
Para empezar
¡Conecte la alimentación del amplificador y otros
Una vez finalizada la exploración
El sintonizador se detiene en el canal memorizado
más bajo. Si desea recuperar los canales seleccionados, podrá seleccionar los canales directamente con
los botones numéricos o los botones CHANNEL K o
L del mando a distancia.
componentes, si es necesario.
1 Presione el botón POWER.
¡La alimentación se conectará.
2 Presione el botón OPEN/CLOSE para abrir
la bandeja de carga del disco.
CÓMO BORRAR (AGREGAR)
CANALES
3 Ponga el disco deseado en la bandeja, con
la etiqueta hacia arriba.
TV/VCR
Puede borrar de la memoria los canales que ya no
recibe o que ve muy raramente. (Por supuesto, puede
volver a agregar a la memoria los canales que haya
borrado de la misma.)
1
Introduzca el número del canal deseado
Presione el botón de flecha K o L hasta que aparezca el número del canal deseado. (También puede utilizar también los botones numéricos o los botones
CHANNEL K/L para introducirlo.) (Ejemplo: CH8)
Presione el botón ENTER. El número del canal
seleccionado se ilumina de color rojo. El canal de
borra de la memoria.
Canal agregado: Se enciende en azul.
Canal borrado: Se enciende en rojo.
Encienda el televisor/DVD/videograbadora
Presione el botón POWER para encender el televisor/DVD/videograbadora.
3
Seleccione “AGREGAR/BORRAR”
Presione el botón de flecha K o L para señalar
“AGREGAR/BORRAR”.
Presione el botón ENTER.
Seleccione “AJUSTE DE CANAL”
Presione el botón SETUP del mando a distancia.
Presione el botón de flecha K o L para señalar
“AJUSTE DE CANAL”.
Luego, presione el botón ENTER.
4 Presione el botón PLAY.
¡La bandeja se cerrará automáticamente y la reproducción comenzará desde el primer capítulo o pista
del disco. Si la reproducción no comienza automáticamente, presione el botón PLAY.
¡Cuando reproduzca un DVD que tenga grabado un
menú de títulos, el menú podrá aparecer en la pantalla.
5 Presione el botón STOP para detener la
reproducción.
– 55 –
ES
0C28
TD851/951(P36-52).QX33
03.3.1 1:56 PM
Page 52
LIMITED WARRANTY
FUNAI CORP. will repair this SYLVANIA product, free of charge in the USA in the event of defect in materials or
workmanship as follows:
DURATION:
PARTS:
FUNAI CORP. will provide parts to replace defective parts without charge for one (1) year from the
date of original retail purchase. Two (2) years for Picture Tube. Certain parts are excluded from this
warranty.
LABOR:
FUNAI CORP. will provide the labor without charge for a period of ninety (90) days from the date of
original retail purchase.
LIMITS AND EXCLUSIONS:
THIS WARRANTY IS EXTENDED ONLY TO THE ORIGINAL RETAIL PURCHASER. A PURCHASE
RECEIPT OR OTHER PROOF OF ORIGINAL RETAIL PURCHASE WILL BE REQUIRED TOGETHER WITH
THE PRODUCT TO OBTAIN SERVICE UNDER THIS WARRANTY.
This warranty shall not be extended to any other person or transferee.
This warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing
or if service was attempted by an unauthorized service center. This SYLVANIA Limited warranty does not apply to
any product not purchased and used in the United States.
This warranty only covers failures due to defects in material or workmanship which occurs during normal use. It
does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not
supplied by FUNAI CORP., or damage which results from accident, misuse, abuse, mishandling, misapplication,
alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this
product or damage which results from fire, flood, lightning or other acts of God.
THIS WARRANTY DOES NOT COVER PACKING MATERIALS, ANY ACCESSORIES (EXCEPT REMOTE
CONTROL), ANY COSMETIC PARTS, COMPLETE ASSEMBLY PARTS, DEMO OR FLOOR MODELS.
FUNAI CORP. AND ITS REPRESENTATIVES OR AGENTS SHALL IN NO EVENT BE LIABLE FOR ANY
GENERAL, INDIRECT OR CONSEQUENTIAL DAMAGES ARISING OUT OF OR OCCASIONED BY THE
USE OF OR THE INABILITY TO USE THIS PRODUCT. THIS WARRANTY IS MADE IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OR IMPLIED, AND OF ALL OTHER LIABILITIES ON THE PART OF
FUNAI, ALL OTHER WARRANTIES INCLUDING THE WARRANTY OF MERCHANTABILITY, AND
FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY DISCLAIMED BY FUNAI AND ITS
REPRESENTATIVES IN THE UNITED STATES.
ALL WARRANTY INSPECTIONS AND REPAIRS MUST BE PERFORMED BY A FUNAI AUTHORIZED
SERVICE CENTER. THIS WARRANTY IS VALID WHEN THE UNIT IS CARRIED-IN TO FUNAI
AUTHORIZED SERVICE FACILITY.
IMPORTANT:
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, YOU MAY HAVE OTHER RIGHTS
THAT VARY FROM STATE TO STATE, IF, AT ANY TIME DURING THE WARRANTY PERIOD, YOU ARE
UNABLE TO OBTAIN SATISFACTION WITH THE REPAIR OF THIS PRODUCT, PLEASE CONTACT FUNAI
CORP.
ATTENTION:
FUNAI CORP. RESERVES THE RIGHT TO MODIFY ANY DESIGN OF THIS PRODUCT
WITHOUT PRIOR NOTICE.
To locate your nearest SYLVANIA Authorized Service Center or for general service procedure,
please call 1-800-968-3429 or write to the following:
FUNAI CORPORATION, INC.
Customer Service
100 North Street; Teterboro, NJ 07608
Tel :1-800-968-3429
http://www.funai-corp.com
PLEASE DO NOT SHIP YOUR UNIT TO THE TETERBORO ADDRESS.
Printed in Malaysia
0EMN02116
TD851UB/TD951UB ★★★★★
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement