Optex Web Site
Welcome To OptexAmerica.com!
1845 W. 205th Street, Torrance, California
Phone: (800) 966-7839 or (310) 533-1500 - Fax: (310) 533-5910
Hours: 8:30am to 5:00pm (Pacific Standard Time) Monday through Friday
Send an e-mail message to:
Service - Technical Support - Web Master - Optex Administration
http://www.optexamerica.com/ [06/08/2000 12:19:15]
Optex Products and Info
Optex Y2K Info
http://www.optexamerica.com/toc4.cfm [06/08/2000 12:19:19]
Security Products
Optex is a leading manufacturer of
high technology security products.
We aggressively develop new
product ideas and technologies to
build quality products that meet our
customer's needs and lifestyles. Our
wide range of indoor and outdoor
motion detectors, photoelectric
detectors, control systems for
burgulary and fire alarm
applications, and closed circuit
television equipment, allow you to
choose Optex equipment for all of
your most critical security needs.
http://www.optexamerica.com/indexes/security.cfm [06/08/2000 12:19:20]
Optex Security - End User
SECURITY - END USER INFORMATION
What should I look for when purchasing security equipment?
Most customers look for long term value. Selecting equipment which exceeds your
expectations, and performs flawlessly for many years, is your best investment. Often,
conditions in the protected premises change during the long life of a security system.
Well designed control panels and detectors meet a wide range of operational
requirements and are the best long term value.
Why should I select Optex equipment?
Optex has produced the finest quality sensors for the security industry since 1979. Our
Passive Infrared detectors and photoelectric detectors have set the standard for false
alarm immunity, high sensitivity, quality, and aesthetic design.
With the purchase of Morse Security Group in 1994, Optex added 70 years of
experience in security control panel and alarm communications technology to our
product offerings. Morse controls have long been the preferred choice for financial,
government, and other high security applications. Morse engineering and design
experience are apparent in the quality and elegant operation of Optex Burglar and Fire
Alarm Systems.
What should I consider when designing my system?
If you've never owned a security system before, you might want to try to keep the
system simple, but still complete. Hopefully this will help you to integrate the security
system into your daily lifestyle as easily as possible. By selecting a control system
which offers extra features, you can start with a more basic system and then add
features later (such as exterior annunciation).
A fire alarm system with smoke detectors is a valuable addition to your security
system and should be considered from the beginning.
How should I select my security service company (installation company)?
http://www.optexamerica.com/security/enduser_sec.cfm (1 of 2) [06/08/2000 12:19:21]
Optex Security - End User
Here again, quality and long term satisfaction are usually buyer's first considerations.
Initial cost savings disappear quickly if the problems develop in the system and the
installer is not available to remedy them.
Do I really need monitoring?
Security systems call for help. Monitoring ensures your call is heard and response is
dispatched.
Additional questions? Please e-mail your questions to us, we'd be happy to reply.
Click Here To Return To The Security Home Page
http://www.optexamerica.com/security/enduser_sec.cfm (2 of 2) [06/08/2000 12:19:21]
Control Panels - Index
Genesys 824
Alpha
Genesys 824R
Genesys 824
Alpha Fire
MDC
Super MDC
Vision
http://www.optexamerica.com/indexes/cpan_index.htm [06/08/2000 12:19:22]
Genesys 824 Alpha Control Panel Specification Sheet
Alphanumeric Display
8 Zone Control Communicator
Expandable to 24 Zones
The New
Genesys Generation
Genesys 824 Alpha provides a variety of unique
features designed to be installer and user
friendly.
5 Year Warranty
●
Alpha and Segmented LCD Keypad Compatibility
The Intelligent Alpha LCD keypad can be programmed with custom zone names either from keypad
or from Remote Downloading Software. You need only to program one alpha keypad with custom
zone names in multiple alpha keypads application. Also it can be used with segmented LCD
keypads for any application.
●
Full Remote Programming Capability from Windows Software
G-824-ALPHA is supported by easy to use download software. (RPU) featuring full remote
programming including custom zone names plus...
- Site initiate down load
- Down load security call back
- Remote Arming/Disarming and much more
●
Keypad Features
- Real time clock
- Auto arming with Pre-Arm warning
- 1-Digit Quick Arm function
- Manual Fire, Panic and Emergency (programmable)
- Segmented LCD / Alpha LCD Keypad / Key Switch or any combination
- LED status indication for Key Switch use
- 16 User Codes w/5 Security Levels
- Guest PIN with Auto Deletion
- User Activated Bell test
●
Additional Features
http://www.optexamerica.com/products/gen824alpha.htm (1 of 3) [06/08/2000 12:19:24]
Genesys 824 Alpha Control Panel Specification Sheet
- Multiple transmission formats including SIA
- Unique "intelligent" two-stage battery charging circuit
- 16 even Alarm Memory with Time Stamp
- 2 Auxiliary Programmable 12 VDC outputs
- Monitors phone and bell
- 2 phone capability
●
Programming Features
- 8 zone expandable to 16 or 24 (fully programmable)
- Select from 5 different Loop Types (Optional E.O.L.)
- 3 different types of Interior Zones designed to reduce false alarms caused by user error
- All zones have Fire capability
- Compatible with 2 or 4 wire Smoke Detector
- 2 Entry/Exit delay times
- Allows for TRUE PARTITIONING including separate Keypads, Alarm Zones and PINs
- Programmable Monitor and Walk-Test modes
●
Long Range Radio Capability
The RF-RM1 Long Range Radio Transmitter is the most cost effective method to ensure that your
customer has the higher level of security available in the even the land line should be cut.
The RF-RM1 transmitter employs the super fast Varitech FSK method of communications to ensure
fast and reliable reporting of all events. Consult your central station for availability of the service.
RF-RM-1 Features:
- No programmers required/Easy Interface (4 wire)
- Reporting by Zone, Opening/Closing, Panic, Fire Emergency and all Housekeeping signals.
SPECIFICATIONS:
Model
Control Cabinet
Primary Power
Standby Power
Continuous Aux Power
Lightning Protection
Keypad
824 Alpha
11 1/2"W x 11 1/2"H x 3 1/2"D
Steel w/hinged cover. Knockout for lock.
Knockouts top, bottom, side and back.
16.5 VAC 20VA transformer (not included)
12 VDC rechargeable Gel type (not included)
750 mA (Max 2Amps for Non UL)
MOV; spark gap
Maximum 4 keypads per system wired with 4 conductor
cable.
http://www.optexamerica.com/products/gen824alpha.htm (2 of 3) [06/08/2000 12:19:24]
Genesys 824 Alpha Control Panel Specification Sheet
Current Draw
Panel = 100 mA
Keypad = G-KP-Alpha: 40 mA (G-KP: 24 mA)
Expander module 29 mA (each)
Fire module 30 mA (each)
GENESYS MODELS:
Model
G-824ALPHA/KP
G-824ALPHA/KP-F
G-KP-ALPHA
G-KP-ALPHA-F
G-KP
G-KP-F
G-EX
G-FM
G-EXC
RF-RM-1
Description
Control / Keypad
Red Control / KP For Fire Applications w/ G-FM
Alpha Keypad
Red G-KP-ALPHA for Fire Applications
Segmented LCD Keypad
Red G-KP for Fire Applications
8 Zone Expander Module
Fire Module
8 Zone Expander Module w/ Cabinet
Long Range Radio Transmitter
Note: G-FM Fire module is required for UL fire applications.
FULL UL LISTING:
.
U.L. 365
U.L. 609
U.L. 985
U.L. 1023
U.L. 1610
U.L. 864 / NFPA71
NFPA72 Chapter 6
Description
Police Connect
Local Alarm
Household Fire Alarm
Household Burgular Alarm
Central Station Burgular Alarm
Central Fire Station
Local Protective Signal System
http://www.optexamerica.com/products/gen824alpha.htm (3 of 3) [06/08/2000 12:19:24]
CCTV - Index
DC-20
Covert Camera and PIR Detector.
WonderTrack Instant high resolution digital recording using High Tech Digital
WT-110
CCTV Technology
http://www.optexamerica.com/indexes/cctv_index.cfm [06/08/2000 12:19:25]
DX-20/DC-20P Specifications Sheet
PROFESSIONAL AND
SOPHISTICATED DESIGN OF THE
CAMERA HOUSING MAKES THE
LENS INCONSPICUOUS!!
With the wide range of cameras and technology
available in today's market, Optex adopts the
high-end post visual processing technology.
●
Easy Installation
The PIR and CCD are set at almost the same angle in production, making the troublesome work of
alignment a thing of the past
http://www.optexamerica.com/products/dc20.htm (1 of 6) [06/08/2000 12:19:28]
DX-20/DC-20P Specifications Sheet
●
HIGH QUALITY PIR
Our state of the art technology offers the best PIR ever used on a covert camera, which adopts the latest
Quad Zone Logic technology, assuring not only that reliable alarm outputs are sent to the alarm system,
but also that crucial pictures are captured by the CCTV system
●
HIGH SENSITIVITY
Clear vision in light conditions as low as 0.5lux
●
AUTO GAIN CONTROL
AGC gives a better picture enabling recognition of the target's face even if the camera is against the
light
●
UNIQUE DEDICATED 2 OUTPUTS / INTEGRATION OF THE ALARM AND CCTV
SYSTEM
There are 2 output relays enabling the integration of the security system and CCTV system by sending
two signals separately
http://www.optexamerica.com/products/dc20.htm (2 of 6) [06/08/2000 12:19:28]
DX-20/DC-20P Specifications Sheet
●
Optional Brackets
FA-1W
Wall Mount Bracket,
Adjustable ±45° Horizonally,
0-20° Vertically Downwards
http://www.optexamerica.com/products/dc20.htm (3 of 6) [06/08/2000 12:19:28]
DX-20/DC-20P Specifications Sheet
FA-3
Compact Wall & Ceiling Mount
Bracket,
Adjustable ±45° Horizonally,
0-10° Vertically Downwards
Click Here To
See The DC-20 Detection Patterns
DC-20
Model
Supply Voltage
Power Consumption
Operating,
Temperature Range
Storage,
Temperature Range
DC-20P(25C)
DC-20P(37C)
12V DC ± 10%
130mA (P,PM type 150mA)
-10°C ~ +50°C (14°C ~ 122°F)
-20°C ~ +60°C (-4°C ~ 140°F)
http://www.optexamerica.com/products/dc20.htm (4 of 6) [06/08/2000 12:19:28]
DC-20P(60C)
DX-20/DC-20P Specifications Sheet
LED Indicator
Dimensions
Environmental
Humidity
Installation Place
Weight
Detection Indicator
H125mm x W70mm X D57mm (4.9" x 2.8" x 2.2")
85% RH max.
indoor only
140g (4.9oz)
CCD Camera
Model
Pickup Element
Video Output
Scanning Method
Resolution
Number of Effective
Pixels
Focal Distance
Lens Type
View Angle
Minimum Illumination
TV Method
Synchronization
DC-20P(25C)
DC-20P(37C)
1/3" interline CCD
1.0Vp-p/75ohms ± 10%
2:1 interlaced
380 TV lines
DC-20P(60C)
510(H) x 492(V)
f = 2.5mm
Conventional
109°(H) x 82°(V)
f = 3.7mm
Pinhole
72°(H) x 54°(V)
0.5 lux
CCIR
inside
f = 6.0mm
Conventional
45°(H) x 34°(V)
Detector
Model
Detection Method
Coverage Detection
Zones
Sensitivity
Relay Output
Warm-up Period
Model List
DC-20P(25C)
DC-20P(37C)
Passive Infrared
DC-20P(60C)
MAX 12 m x 12 m (40 ft x 40 ft) 85° wide
0.3 ~ 1.5 m/sec. (1 ~ 5 ft./sec.)
N.C. or N.O. 28VDC 0.2A max
Approx. 20 sec.
Conventional Lens
2.5mm
6.0mm
http://www.optexamerica.com/products/dc20.htm (5 of 6) [06/08/2000 12:19:28]
Pinhole
3.7mm
DX-20/DC-20P Specifications Sheet
CCIR
EIA
Camera
Camera + PIR
Camera + PIR + Mic
Camera
Camera + PIR
Camera + PIR + Mic
DC-20(25C)
DC-20P(25C)
DC-20PM(25C)
DC-20(25E)
DC-20P(25E)
DC-20PM(25E)
http://www.optexamerica.com/products/dc20.htm (6 of 6) [06/08/2000 12:19:28]
DC-20(60C)
DC-20P(60C)
DC-20PM(60C)
DC-20(60E)
DC-20P(60E)
DC-20PM(60E)
DC-20(37C)
DC-20P(37C)
DC-20PM(37C)
DC-20(37E)
DC-20P(37E)
DC-20PM(37E)
DC-20/DC-20P Detection Patterns
http://www.optexamerica.com/products/dc20detpatt.htm [06/08/2000 12:19:30]
Passive Infrared Sensors (Outdoor) - Index
LX-40/80N
VX-40 / 40A
http://www.optexamerica.com/indexes/piso_index.htm [06/08/2000 12:19:30]
Wireless 1000(E)
LX-40/80N Specification Sheet
Sunlight Immune
Detector:
A New Standard For
Outdoor Detection
Outdoor Detection with the LX-40/80N, The
Smart Way to Expand Your Business
Opportunities
OPTEX's outdoor detection offers many advantages
for your business. The LX-40/80N is not only simple
to install, but provides greater reliability against false
alarms caused by sunlight.
Conventional outdoor passive infrared detectors often
produce false alarms caused by sunlight. But,
OPTEX's LX-40/80N employs Double Conductive
Shielding which resists more than 50,000 lux of
sunlight (e.g. during sunrises and sunsets). This
provides highly stable performances, while allowing
the units to be used in many different applications.
●
Patented Double Conductive Shielding
Double filtering and conductive metal shielding of the Pyro blocks out visible light and RFI. This
allows only infrared energy to reach the pyroelectric elements.
http://www.optexamerica.com/products/lx40.htm (1 of 4) [06/08/2000 12:19:32]
LX-40/80N Specification Sheet
●
Realiable Performance
❍
❍
❍
❍
❍
❍
❍
●
Easy Installation
❍
●
Quick Installation
The LX-80N, for example, provides 80 ft (24 m) long range narrow detection, eliminating the
need for long outdoor wiring when the unit is mounted on a building.
Design Durability
❍
❍
❍
●
Temperature Compensation Circuit
Automatically adjusts the detection sensitivity according to the environmental temperature.
Selectable Detection Patterns
Multi-level or Pet Alley detection patterns can be selected by sliding the PCB and flipping the
mirror.
Area Masking Strips (LX-40 Only)
Unwanted detection areas can be easily eliminated by attaching supplied masking strips.
Selectable Sensitivity
Selectable Pulse Count: 1 or 2
Day or Night Mode
Form C Relay Output
Highly Durable and Heat Resistant Housing and Lens
High Grade UV-Resistant Lens
Stainless Steel Screw
Applications
❍
❍
Activation of CCD camera, light, siren, and/or other devices
Front and/or backyard alongside fences, garage / parking lots, delivery door, etc.
http://www.optexamerica.com/products/lx40.htm (2 of 4) [06/08/2000 12:19:32]
LX-40/80N Specification Sheet
●
Options
❍
❍
CA-1W: Multi-Angle Wall Mount Bracket
Horizontally: ±45°
Vertically: 0° to 20° Downward
CA-2C: Ceiling Mount Bracket
Horizontally: ±45°
Vertically: 0° to 20° Downward
Click Here To See The
LX-40/80N Detection Patterns
Model
Detection Method
LX-40
LX-80N
Passive Infrared
http://www.optexamerica.com/products/lx40.htm (3 of 4) [06/08/2000 12:19:32]
LX-40/80N Specification Sheet
Coverage
Detection Zones
Mounting
40ft x 50ft (12m x 15m)
120° wide
80ft x 6ft (24m x 2m)
long range
Normal Area: 40 zones
Multi-Level Area: 12 zones
Pet alley area: 18 zones
Pet alley area: 4 zones
Normal Area: 8.3ft (2.5m) max.
Pet alley area: 4 ~ 5ft (1.2 ~ 1.5m)
Detectable Speed
1 ~ 3.3ft/sec. (0.3 ~ 1.0m/sec)
Sensitivity
Adjustment
Selectable 3 position (H,M,L)
LED Indicator
LED lights on during detection
Alarm Period
2.0 ± 1sec. (Delay timer)
Alarm Output
NC. NO 28V DC 0.2A Max
Tamper Switch
Opens when cover removed.
Pulse Count
"2" position: 2 (20 ± 5 sec.)
"TEST" mode: 1 pulse
Photocel
Adjustment
Day to night mode (Approx. 10 to 100,000 lux)
Warm-up Period
Approx. 60 sec.
Power Input
12VDC ± 10%
Current Draw
Installation Place
25mA max.
Indoor or outdoor on the wall
Operating
Temperature
-4°F ~ +122°F (-20°C ~ +50°C)
Environment
Humidity
95% max
Weight
5.3oz (150g)
*Specifications and design are subject to change without prior notice.
NOTE: This unit is designed to detect movement of an intruder and activate an
alarm control panel. Being only part of a complete alarm system, we connot accept
responsibility for any damages or other consequences resulting from an intrusion.
http://www.optexamerica.com/products/lx40.htm (4 of 4) [06/08/2000 12:19:32]
LX-40/80N Detection Patterns
http://www.optexamerica.com/products/lx40detp.htm (1 of 2) [06/08/2000 12:19:34]
LX-40/80N Detection Patterns
http://www.optexamerica.com/products/lx40detp.htm (2 of 2) [06/08/2000 12:19:34]
VX-40/40A Specifications Sheet
Introducing The Most Innovative
Idea In Outdoor Detection. Optex's
Advanced "MDP" (Multiple
Detection Pattern) Technology.
Optex's advanced PIR technology takes a giant leap
into the future of outdoor detection. Our patented
design allows this sensor to adapt to many different
applications and offer reliable detection and unique
deterrent capability.
The VX-40 Series has unique technology which
makes it absolutely the most stable outdoor sensor
which utilizes Passive Infrared Technology. Designed
to provide Reliable Performance, Ease of Installation
and Multiple Applications for the Dealer and End
User, the VX-40 allows your customer the ability to
utilize perimeter awareness in their home or business.
●
The Highest Reliability Available in Outdoor Detection
The patent pending "MDP" Technology eliminates the chance of false alarm caused by moving objects
or small animals within the detection area. The VX-40 includes the first Layered Detection Pattern
which provides logic for discrimination of objects in the detection area. The upper zone stays parallel
to the ground at all times and the lower zone is adjustable from 6.7ft. (2.0m) to 40ft. (12m). Only when
both upper and lower zones are activated will the VX-40 generate an alarm.
●
Limited Detection Range Function
The detection range of the VX-40 can be limited to avoid detecting unwanted objects. By eliminating
detection range, false alarms due to unwanted movement (i.e. cars, persons or animals outside the
detection area) can be reduced.
●
Size Judging Function
The VX-40 is designed to discriminate between large and small objects. By utilizing this ability, false
alarms due to small animals can be virtually eliminated.
http://www.optexamerica.com/products/vx40.htm (1 of 6) [06/08/2000 12:19:36]
VX-40/40A Specifications Sheet
●
Bright Light Disturbance Immunity with Double Conductive Shielding
The VX-40 is equipped with Patented Double Conductive Shielding Technology. A special conductive
filter covers the element window allowing infrared energy to pass through while blocking and
grounding out light and RFI sources.
●
High Durable Housing & Lens
●
Weather Proof Structure (IP54)
●
Easy Installation
Installation of the VX-40 has been simplified by the addition of a conduit access in the bottom of the
unit. You can conveniently install the VX-40 anywhere since it can be wired either through a conduit
access in the bottom of the unit or through a wiring access on the back of the unit. In addition,
rubberized grommets increase the resistance of the sensor to the attack of natural elements.
http://www.optexamerica.com/products/vx40.htm (2 of 6) [06/08/2000 12:19:36]
VX-40/40A Specifications Sheet
❍
❍
❍
❍
Wiring Convenience
Wiring can enter the sensor from the top or bottom, making installation quick and easy.
Built-In Conduit Entry
A conduit can be installed directly into the bottom of the unit by removing the knockout on
the cover.
Area Masking Plate
Unwanted detection area(s) can be easily eliminated by attaching supplied masking plates.
Area Angle Adjustment
The detection area can be adjusted 45° left or right from the center to allow for custom
applications for the sensor.
●
Extensive Application
By connecting to additional detectors such as PIRs, Active IR Beams, or Magnetic Contacts, the VX-40
can provide additional features without the use of any special control panel. Self-contained functions
can offer not only higher reliability but also the ability to be utilized in various applications.
❍ Detection Area Extension Function
Wiring two VX-40 sensors together and selecting the "OR" Mode will allow the detection
pattern to be effectively doubled.
❍ Directional Detection Function
The VX-40 can also be used in conjunction with another sensor to create even greater
stability. By selecting the "AND" Mode and programming which sensor should be activated
first (DIP Switch Programming), the VX-40 can sense direction and will activate only if
motion is in a specific direction.
❍ Sequentially Confirmed Alarm Containment
With this option selected, an alarm will only be generated if two detectors activate
sequentially and separately. This function dramatically increased the reliability of the system.
It is no longer necessary to reduce sensitivity or parallel sensors together. The logic is all
internally controlled.
●
Voice Warning Function (VX-40A Model Only)
When the system is armed, the Voice Warning Feature (Weatherproof speaker inside sensor) delivers
one of two types of voice messages to anyone entering the protected area. This warning is designed to
deter a would-be intruder from continuing towards the protected area.
●
Various Applications
The VX-40 is equipped to provide Directional Access Control features. Applications for this
technology include opening an automatic gate when approached from one direction, counting cars or
people going one direction through an area and not counting those going the other way.
http://www.optexamerica.com/products/vx40.htm (3 of 6) [06/08/2000 12:19:36]
VX-40/40A Specifications Sheet
●
Other Features Include:
- Selectable NC or NO Alarm Output
- Temperature Compensation Circuit
- Illuminance Sensor
- Day-Night Mode
- Sensitivity Adjustment: Low, Medium, High
- LED On/Off Switch
- Selectable Pulse Count: 2 or 4
- Spare Terminals
Click Here To See The
VX-40's Detection Patterns
http://www.optexamerica.com/products/vx40.htm (4 of 6) [06/08/2000 12:19:36]
VX-40/40A Specifications Sheet
Model
Detection Method
Coverage
Detection Zones
Mounting Height
Sensitivity
Detectable Speed
Power Input
Current Draw
VX-40
VX-40A
Passive Infrared
12m (40ft) 90° wide
14 zones
0.8 ~ 1.2m (2.7 ~ 4ft)
1.6°C (3°F) at 0.6m/s (2ft/s)
0.3 ~ 1.5m/s (1 ~ 5ft/s)
9.5 ~ 18VDC
NC Normal 25mA Max 28mA Normal 25mA Max 180mA
NO Normal 10mA Max 35mA Normal 12mA Max 200mA
Alarm Period
2 ± 1sec
Alarm Output
Selectable NC/NO:28VDC 0.2A Max
Tamper Switch
NC Opens when cover removed
Pulse Count
20 ± 5 sec 2 or 4
Warm-up Period
Approx 30sec (LED blinks)
LED is blinking durin warm-up period
LED Indicator
Alarm condition
Weather proof
IP54
Operating Temperature
-20 ~ +50°C (-4 ~ +122°F)
Environment Humidity
95% Max
RF Interference
NO Alarm 30V/m
Mounting
Wall, Pole, Conduit and Electrical Box
http://www.optexamerica.com/products/vx40.htm (5 of 6) [06/08/2000 12:19:36]
VX-40/40A Specifications Sheet
Weight
Standard Accessories
550g (19.4oz)
Pole Mount Kit, Screw Kit, Area Masking Plate
*Specifications and design are subject to change without prior notice.
NOTE: This unit is designed to detect movement of an intruder and activate an alarm
control panel. Being only a part of a complete system, we cannot accept
responsibility for any damages or other consequenes resulting from an intrusion. This
product conformas to the category "Residential, Commercial and Light Industry" of
EMC Directive 89/336 EEC.
http://www.optexamerica.com/products/vx40.htm (6 of 6) [06/08/2000 12:19:36]
VX-40/40A Detection Patterns
Length of lower finger decides detection length. The upper detection finger
stays parallel to the ground all the time while the lower detection finger moves
as shown depending on the switch position. Consequently, the length of the
detection area is limited by the length of the lower finger since both the upper
and lower fingers have to be blocked at the same time to activate the sensor.
http://www.optexamerica.com/products/vx40detpatt.htm (1 of 2) [06/08/2000 12:19:38]
VX-40/40A Detection Patterns
http://www.optexamerica.com/products/vx40detpatt.htm (2 of 2) [06/08/2000 12:19:38]
Passive Infrared Sensors (Indoor) - Index
Standard Ranges
(40' x 40' Wide Angle, 80' curtain pattern or less)
DX-40
PIR/Microwave detector with Anti-Masking, Microwave Shaping, Microwave Watchdog
circuitry, and Quad Zone Logic PIR.
EX-35T
"Flip Lens" provides 35'x35' wide angle or 5'x5' long range pattern, built-in pet alley option
and selectable pulse count.
FX-40
40'x40' pattern with look down zone or 60' curtain with optional lens, temperature
compensation and sealed optics.
FX-360
Ceiling mount detector for easy installation, superior aesthetics, and less blockage. 25' to
40' detection area on 8' to 12' ceiling.
RX-40PI
Quad Zone Logic provides pet immunity to eliminate false alarms from objects 16" tall or
less. High sensitivity allows use in virtually all apps.
Extra Long Ranges
(Designed specifically for large area coverage)
CX-50
Dual purpose lens for 50'x50' (108 zones) or 80'x6' curtain pattern, double conductive
shielding, anti-masking available (CX-50AM).
CX-70M
70'x70' wide angle or 150'x8' long range patterns on dual purpose lens, double conductive
shielding and sealed optics.
SX-45C
45'x45'ceiling mount with in-line Quad elements for ceiling heights from 7' to 18', dense
coverage, attractive design.
http://www.optexamerica.com/indexes/pisi_index.htm (1 of 2) [06/08/2000 12:19:39]
Passive Infrared Sensors (Indoor) - Index
SX-75C
75'x20' ceiling mount with in-line Quad elements for ceiling heights from 7' to 18', dense
coverage, attractive design.
SX-360Z 276 zones in a 360° pattern, Zooms to compensate for ceiling height, delivers 60' diameter
pattern on 6'-16' ceilings.
http://www.optexamerica.com/indexes/pisi_index.htm (2 of 2) [06/08/2000 12:19:39]
DX-40/40Plus Specifications Sheet
DX-40 Combines Advanced Optical
PIR Technology and Unique
Microwave Detection
DX-40 is the result of Optex's advanced research with
PIR and microwave technology. Unique
advancements include Patent Pending
"MICROWAVE AREA SHAPING
TECHNOLOGY" and PIR technology with New
Spherical Lens to improve QUAD ZONE LOGIC in
a compact housing. Mechanical design of this product
will offer easy and trouble-free installation. DX-40
has features that will satisfy almost every installation.
●
Microwave Technology - Patent Pending "Area Shaping Technology"
Optex Research and Development Department have created a breakthrough in Microwave Detection.
The DX-40 reduces one of the biggest weak points of microwave detection, that is the penetration of
http://www.optexamerica.com/products/dx40.htm (1 of 6) [06/08/2000 12:19:42]
DX-40/40Plus Specifications Sheet
walls and unwanted detection of movement outside the coverage area. In addition, the detection area
has uniform sensitivity which minimizes false activation's caused by spot movement in the detection
area, i.e. small animals. The DX-40 is a new dimension in microwave technology.
●
Passive Infrared Technology - Patented Quad Zone Logic with New Spherical Lens
By utilizing Optex Advanced Optical Technology, the DX-40 creates evenly distributed sensitivity
throughout the detection area. Accurate focus creates even sensitivity and high resistance to spot
temperature changes. Other detectors may have inconsistent detection creating hot spots (false alarm
can occur) and dead spots (no detection). In addition, the New Spherical Lens contributes to a superior
aesthetic appearance which end users will appreciate.
●
Optex Design and Mechanical Technology
- Easy installation and wiring are engineered into this compact housing.
- Easy Microwave Area Adjustment:
❍ Long or Short Distance Selector Switch
❍ Low, Medium or High Sensitivity Adjustment
●
Re-Enforced with Electronic Analysis
http://www.optexamerica.com/products/dx40.htm (2 of 6) [06/08/2000 12:19:42]
DX-40/40Plus Specifications Sheet
❍
Detection Area Size Configuration - "Microwave Area Shaping" and "Quad Zone
Logic"
The Microwave Area can be easily shaped to fit the desired area and have even sensitivity. In
addition, Quad Zone Logic in the PIR provides high tolerance to spot temperature changes
and movements caused by small animals, heating vents, moving curtains and vibrations
caused by big machinery.
●
No Penetration
❍ No False Alarms due to Penetration through walls
Passive Infrared does not detect through walls and is never affected by movement beyond these
boundaries.
❍ No False Alarms by Spot Temperature Changes
DX-40 is not affected by spot temperature changes or by sunlight caused by the movement of
sunlight through a detection area.
❍ Enhanced Sealed Optics (patent pending)
●
No Temperature or Light Disturbance
❍ Trouble-Free Installation
Microwave Area Shaping allows for simple two step adjustment. By making minor
adjustments to the Long or Short Range Selector and the Low, Medium, High Sensitivity
Volume, the microwave can be shaped to match room size. This technology will not only
reduce installation hassle but will reduce false alarms caused by penetration of walls by the
microwave detector.
Wiring Guide and Wide Space at Terminals - Increases Ease of Installation
http://www.optexamerica.com/products/dx40.htm (3 of 6) [06/08/2000 12:19:42]
DX-40/40Plus Specifications Sheet
Easy To Operate Pin Switches (with instruction directly on the detector)
High Visibility LED Display (3 LEDs) - selectable On/Off
Easy Knockout
●
Improved Tolerance to Spot Movements
❍ False Safe Technology - Automatic Trouble Monitoring
Passive Infrared does not detect through walls and is never affected by movement beyond these
boundaries.
Microwave Watchdog Circuit (Self-checking function)
When microwave operation fails, DX-40 automatically switches to single PIR operation in
Enhanced Reliability Mode avoiding Missed Alarms.
Anti-PIR Tamper Function (Patent Pending)
When PIR Detection fails, (something near the detector blocking the field of view) a trouble
output will generate via the * alarm output (Selectable option with DX-40) and LED Display.
(*DX-40PLUS has separate Relay Output)
●
DX-40Plus Enhanced Model
❍ Separate Relay Output for Automatic Trouble Monitoring
❍ Alarm Memory, Selectable Positive or Negative Input
❍ LED Remote On/Off Control Input from Control Panel
❍ Metal Shielded Relay
●
Optional Brackets
FA-1W
Wall Mount Bracket,
Adjustable ±45° Horizonally,
0-20° Vertically Downwards
http://www.optexamerica.com/products/dx40.htm (4 of 6) [06/08/2000 12:19:42]
DX-40/40Plus Specifications Sheet
FA-3
Compact Wall & Ceiling Mount
Bracket,
Adjustable ±45° Horizonally,
0-10° Vertically Downwards
Click Here To
See The DX-40 Detection Patterns
DX-40
Detection Method
Passive Infrared and Microwave
Coverage
40 x 40 ft (12m x 12m) 85° wide
Detection Zones
82 zones (PIR)
Mounting Height
5 ~ 8 ft. (1.5m ~ 2.4m)
Sensitivity
Detectable Speed
3°F (1.6°C) at 2 ft. / sec. (.6m / sec.), 40ft (12m)
1 ~ 5 ft. / sec. (.3 ~ 1.5m / sec.)
Alarm Period
Approx. 2 sec.
Alarm Output
N.C., 28VDC 0.2A max.
http://www.optexamerica.com/products/dx40.htm (5 of 6) [06/08/2000 12:19:42]
DX-40/40Plus Specifications Sheet
Tamper Switch
N.C., Opens when cover is removed.
Warm Up Period
LED Indicator
Approx. 30 sec.
Flicker during warm-up.
RED: Alarm, Alarm Memmory, and Trouble
Indicator
YELLOW: MW and Trouble Indicator
GREEN: PIR and Trouble Indicator
Power Input
Current Draw
9 ~ 18VDC
12mA(normal), 35mA(max.) at 12 VDC
RF Interference
No alarm 30V/m
Operating Temperature
14°F ~ +122°F (-10°C ~ +50°C)
Environmental Humidity
95% max.
Microwave Frequency
Weight
9.90GHz/10.525GHZ
10.687GHz (UK Version)
5.3oz(150g) - Plastic Antenna Version
8.1 oz(230g)- Metal Antenna Version
DX-40Plus
Current Draw
DL Terminal
Alarm Memory
Trouble Output
Microwave Frequency
17mA (normal),
40mA(max.) at 12
VDC
LED remote control
terminal
Selectable positive
and negative control
N.C., 28VDC 0.2A
max.
9.90GHz/10.525GHZ
10.687GHz (UK
Version)
*Specifications are subject to change without notice for improvement.
http://www.optexamerica.com/products/dx40.htm (6 of 6) [06/08/2000 12:19:42]
DX-40 Detection Patterns
http://www.optexamerica.com/products/dx40detpatt.htm [06/08/2000 12:19:43]
EX-35 Specifications Sheet
Twice The Features
At Half The Cost
The EX-35 Combines A Unique Dual Purpose
Lens, Patented Multi-Focus Technology and
Selectable Sensitivity to Create 4 Precise Detection
Pattern Selections.
The EX-35 breaks the mold of low cost, quality
deficient detectors. You can select between precise
Wide Angle or Long Range Coverage, and also
Multi-Level or Pet Alley Detection Patterns. By
incorporating our Patented Multi-Focus Technology
into the Spherically Designed Lens, the EX-35 has
successfully eliminated sensitivity problems caused
by changes in detection patterns.
●
Advanced Design Multi-Purpose Spherical Lens
Unique technology provides unmatched optical performance for Wide Angle and Long Range
Detection in Multi-Level or Pet Alley Patterns, using the same lens surface.
●
Selectable Detection Patterns
The EX-35 provides reliable and precise detection performance.
❍ Wide Angle and Long Range Detection Patterns
By simply rotating the sperical lens, you select between Wide Angle and Long
Range Detection Patterns.
❍ Multi-Level and Pet Alley Detection Patterns
Multi-Level and Pet Alley Detection Patterns can be selected by simply sliding
the P.C.B. up or down.
●
Patented Multi-Focus Lens
http://www.optexamerica.com/products/ex35.htm (1 of 4) [06/08/2000 12:19:45]
EX-35 Specifications Sheet
Creates zones with high vertical density, providing maximum detection sensitivity that remains stable
even in high temperature conditions.
●
False Alarm Protection
❍ RFI Protection
No alarm at 20V/m from 100MHz to 1GHz.
❍ Temperature Protection
No alarm during temperature changes from -4°F to +122°F (-20°C to +50°C)
❍ Noise Reduction Circuit
❍ Selectable Pulse: 2 or 4
❍ LED On/Off Switch
●
Optional Multi-Angle Bracket
❍ FA-2C: Ceiling Mount
❍ EA-1W: Wall Mount
●
Versions
❍ EX-35
❍ EX-35T: Tamper Switch
❍ EX-35V: Tamper Switch and Alarm Memory
Click Here To
See The EX-35 Detection Patterns
http://www.optexamerica.com/products/ex35.htm (2 of 4) [06/08/2000 12:19:45]
EX-35 Specifications Sheet
Model
Detection Method
Coverage
EX-35
EX-35T
Passive Infrared
WIDE: 35 ft. x 35 ft. (11m x 11m) 85° Wide
LONG: 55 ft. x 5.5 ft. (17m x 1.7m) Long Range
Detection Zones
WIDE: 64 zones / 28 zones (Pet Alley)
LONG: 12 zones / 4 zones (Pet Alley)
Mounting Height
Normal: 4 ~ 8 ft. (1.2m ~ 2.4m)
Pet Alley: 2 ~ 4 ft. (.6 ~ 1.2m)
Sensitivity
Detectable Speed
3°F (1.6°C) at 2 ft. / sec. (.6m / sec.)
1 ~ 5 ft. / sec. (.3 ~ 1.5m / sec.)
LED Indicator
Alarm Indicator Optional
Alarm Period
Approx. 2.5 sec.
Alarm Output
N.C., 28V DC., 0.2A max
N.C., Opens when
­
cover is removed.
Approx. 20 sec. 2 or 4 (When using long range,
always set pulse count selector on "2")
Tamper Switch
Pulse Count
Warm Up Period
http://www.optexamerica.com/products/ex35.htm (3 of 4) [06/08/2000 12:19:45]
Approx. 30 sec.
EX-35 Specifications Sheet
Power Input
9.5 ~ 14V DC
Current Draw
18mA max.
Weight
Operating
Temperature
Environmental
Humidity
RF Interference
3.2 oz. (90 g)
-4°F ~ +122°F (-20°C ~ +50°C)
95% max.
No alarm 20V/m
*Specifications are subject to change without notice for improvement.
Model
Alarm Memory
Current Draw
V Version (Alarm Memory)
EX-35V
EX-35V(P)
Armed:
Armed:
OPEN or +5 ~ 14V
0 ~ 1V DC
DC
18mA (normal), 25mA (max.)
http://www.optexamerica.com/products/ex35.htm (4 of 4) [06/08/2000 12:19:45]
EX-35 Detection Patterns
http://www.optexamerica.com/products/ex35detpatt.htm (1 of 2) [06/08/2000 12:19:46]
EX-35 Detection Patterns
http://www.optexamerica.com/products/ex35detpatt.htm (2 of 2) [06/08/2000 12:19:46]
FX-40 Series Specifications Sheet
"Reliability" - The Keyword in PIR
Detection
OPTEX reliability will surpass all
your expectations.
The combination of the stable, secure performance
of OPTEX optical technology and simplified
installation creates a new standard in sensor
reliability.
When thinking about sensors, think OPTEX. Our
Multi-Focus Optics, Spherical Lens Design and
superior optical technology provide precise detection
capability and durability for unbeatable performance.
OPTEX's unique sensors satisfy your everyday needs
- simplified installation combined with small
innovations like easy wire knockouts and invaluable
wiring guide convenience.
STANDARD VERSION FX-40/40L
Performance
●
Patented Multi-Focus Optics
The highly accurate and reliable detection pattern will maintain its sensitivity throughout the entire
detection area even in high temperature or low contrast environments. Multi-Focus Optics create an
extremely high vertical zone density, two or three times the size of conventional PIRs. These taller
zones capture the entire body mass and enable detection of even the smallest temperature contrast
against the temperature of the background. In addition, the vertical detection density has been improved
to take into account dead zones created by furniture or partitions.
http://www.optexamerica.com/products/fx40.htm (1 of 7) [06/08/2000 12:19:49]
FX-40 Series Specifications Sheet
●
Look Down Zone
The Look Down Zone creates greatly improved vertical sensitivity.
●
Sealed Optics
Prevents drafts and small insects from getting on to the pyroelectric element. This practically
eliminates the chance of false alarm due to these causes since the pyro is sealed with the inside molding
of the housing cover.
●
False Alarm Protection
- RFI Protection: No alarm at 20 V/m from 100MHz to 1GHz
- Temperature Protection: No alarm during temperature changes from -4° to +122°F (-20° to +50°C)
●
LED ON/OFF Switch
●
Selectable Pulse Count: 2 or 4
●
Tamper Switch (FX-40/40L/40D/40DL)
●
Selectable Alarm Memory (Polarity) (FX-40L/40DL): Positive or Negative
●
Spherical Lens Design
Conventional flat lenses inevitably create sensitivity distortion problems when they are bent to fit a
curved housing. OPTEX's spherically designed lens will obtain sharp detection because no bending is
required.
Designed to collect IR energy from the detection area, and focus it directly onto the pyro.
http://www.optexamerica.com/products/fx40.htm (2 of 7) [06/08/2000 12:19:49]
FX-40 Series Specifications Sheet
Since a flat lens is "bent," sensitivity distortion occurs at both sides of the lens (the lens surface in not
directing IR energy correctly), resulting in poor sensitivity for long distance detection applications.
●
ECO Technology (Environmental Compensation from OPTEX)
The FX-40 series features "ECO technology." This technology is designed to increase the sensor's
resistance to all kinds of environmental disturbances. Logic built into the chip allows the sensor to
recognize, discriminate and adjust for temperature changes within the sensor's environment. This
technology also makes the unit less susceptible to false alarms due to RFI disturbances.
●
Special Custom-Made Pyro Electric Element
●
Temperature Compensation Circuit
The Temperature Compensation Circuit will increase detection capability under high temperature
conditions where the background temperature is similar to that of the human body. It maintains a high
level of false alarm protection while providing accurate detection by automatically adjusting its
sensitivity according to the environmental temperature.
Easy Installation
●
No Vertical Adjustment
Vertical area adjustment and dead zones are eliminated by high density detection zones.
●
Easy Wiring Knockout
Wiring knockouts can be opened with a simple push from a screwdriver. Making and adjusting wiring
holes to the right width for the cables is much easier.
●
Wiring Guide & Wide Wiring Space
●
Easy-to-View LED
●
Spare Terminal
http://www.optexamerica.com/products/fx40.htm (3 of 7) [06/08/2000 12:19:49]
FX-40 Series Specifications Sheet
Design Durability
●
Hard & Durable Spherical Lens
OPTEX's Spherical Lens provides higher durability against shocks compared to ordinary PIRs using
flat fresnel lenses or mirrors.
●
PC Board Protection Wall
Damage caused by the tip of the screwdriver, etc. to the PC board can be easily prevented by the PC
Board Protection Wall.
●
Non-Distortion Chassis
●
Attractive Design
SUPERIOR VERSION FX-40D/40DL
Greater Performance Double Conductive Shielding Commercial Market
●
Patented Double Conductive Shielding of Pyro Electric Element
The Double Conductive Shielding lets infrared energy pass through, but blocks and grounds out the
RFI and light sources since it features a special conductive filter that covers the element window. A
conventional metal shielded pyro electric element has an open window for infrared energy to enter.
This allows RFI and light to enter and does much less to protect against many types of interference.
●
False Alarm Protection
- RFI Protection - No alarm against 10W transmitter with 3.3ft (1.0m) with a field strength of 30V/m
within the range of 100MHz to 1GHz.
- Visible Light Protection - Provides a high protection level that exceeds H4 halogen (car headlight)
within 8ft (2.4m) or 50,000lx of morning sunlight reflection within the detection area.
- Temperature Protection - No alarm in high, low and changing temperatures from -4° to +122°F (-20°
to +50°C)
Options
●
FA-3 Options
Wall & Ceiling Mount Brackets:
Horizontally: 45° / Vertically: 0° to 15° downwards
http://www.optexamerica.com/products/fx40.htm (4 of 7) [06/08/2000 12:19:49]
FX-40 Series Specifications Sheet
●
FL-60N
- Long Range (Extremely Dense Multi Layer Curtain) Lens
Click Here To See The
FX-40's Detection Patterns
Model
FX-40, FX-40D
Detection Method
Coverage
Passive infrared
WIDE: 40ft x 40ft (12m x 12m) 85°wide
Detection Zones
WIDE: 72 zones
Mounting Height
NORMAL 5 ~ 8ft (1.5m ~ 2.4m)
Sensitivity
3°F (1.6°C) at 2ft/sec. (0.6m/sec.)
Detectable Speed
1 ~ 5ft/sec. (0.3 ~ 1.5m/sec.)
LED indicator
Alarm indicator optional
Alarm Period
Approx. 2.5 sec.
http://www.optexamerica.com/products/fx40.htm (5 of 7) [06/08/2000 12:19:49]
FX-40 Series Specifications Sheet
Alarm Output
N.C., 28V DC 0.2A max.
Tamper Switch
N.C., Open when cover is removed
Pulse Count
Approx. 20 sec. 2 or 4
Warm-up Period
Approx. 30 sec.
Power Input
9.5 ~ 16VDC
Current Draw
17mA (max.)
Weight
3.2 oz. (90g)
Operating Temperature
Environmental
Humidity
RF Interference
-4°F ~ +122°F (-20°C ~ +50°C)
95% max.
NO Alarm 20V/m (FX-40/40L)
NO Alarm 30V/m (FX-40D/40DL)
*Specifications and design are subject to change without prior notice.
L Version (Alarm Memory)
Model
Polarity
Alarm Memory
Current Draw
FX-40L, FX-40DL
Positive
Negative (Cut jumper)
armed: 0 ~ 1VDC
(grounded)
18mA (normal), 25mA (max.)
armed: OPEN or +5 ~ 16
FL-60N: Optional Lens for Long Range
(Extremely Dense Multi Layer Curtain) Area Pattern
LONG: 60ft x 6ft (18m x 1.8m) Long
Coverage
Range
Detection Zones
LONG: 20 ZONES
*Accessories: Two Mounting Screws
*FL-60N: Pack of 5
NOTE: This unit is designed to detect movement of an intruder and activate
an alarm control panel. Being only a part of a complete system, we cannot
accept responsibility for any damages or other consequences resulting from
an intrusion. This product conforms to the category "Residential, Commercial
and Light Industry" of EMC Directive 89/336 EEC.
http://www.optexamerica.com/products/fx40.htm (6 of 7) [06/08/2000 12:19:49]
FX-40 Series Specifications Sheet
http://www.optexamerica.com/products/fx40.htm (7 of 7) [06/08/2000 12:19:49]
CX-40R & CX-60NR Detection Patterns
http://www.optexamerica.com/products/fx40dpat.htm (1 of 2) [06/08/2000 12:19:50]
CX-40R & CX-60NR Detection Patterns
http://www.optexamerica.com/products/fx40dpat.htm (2 of 2) [06/08/2000 12:19:50]
Optex Photobeams - Index
Dual Beam Photobeams for Outdoor Use
AX-70T /
AX-130T
Outdoor, dual beam photoelectric detectors for 70' and 130' ranges.
High immunity to fog and snow, and automatic gain adjustment.
AX-100 / 200 Plus 100' and 200' beams feature 4x greater lightning protection than industry
AX-100/200 Alpha standard, rubber "O" ring seals, and 450x signal strength.
AX-250 / 500 Plus
AX-350 /
650 MKII
250' and 500' beams feature shock resistant covers, 14kV lightning protection,
and the industry's largest beam spread.
Our longest range beams include Plus Series features and patented IASC
technology for transmitter and receiver alignment readouts.
Specialty Photobeams
OS-1C /
OS-2C
Miniature photobeams with .6 inch (1.5mm) sensor heads and up to 33' (10m) detection
range.
BX-100
'BoundryGard' dual beam photoelectric detector mounts directly to building exterior.
Provides perimeter protection before attack.
AX-100S / Indoor photoelectric beams which mount onto single gang electrical box, surface or
AX-100SR recessed models.
http://www.optexamerica.com/indexes/phelec_index.htm [06/08/2000 12:19:51]
AX-70T / AX-130T Specification Sheet
The "99% Solution"
Twin Beam Photoelectric
Detectors
· Compact design, indoor/outdoor use
· Reliably withstands as much as 99% loss of beam
energy
· Two synchronized beams of pulsed infrared energy
· Maximum arrival distance is 10 times longer than
rated operating distance
NOTE: The AX-70T should be upgraded to the
AX-100Plus and the AX-130T should be upgraded to
the AX-200Plus as they provide better performance.
●
Rain, Fog and Snow Protection
❍
❍
❍
Two beams of pulsed infrared energy provide reliable operation despite as much as 99%
blockage of beam energy caused by heavy rain, dust storm, fog, or falling snow.
Automatic Gain Control (AGC) circuit continually monitors gradual changes in signal
strength caused by weather conditions and adjusts the trigger level accordingly, to maintain
proper sensitivity.
Signal Wave of Beam Output
http://www.optexamerica.com/products/ax70t.htm (1 of 4) [06/08/2000 12:19:54]
AX-70T / AX-130T Specification Sheet
●
Protection Against Birds, Insects and Falling Leaves
❍
❍
●
Frost, Dust and Insect Protection
❍
●
Twin beams require simultaneous interruption to trigger an alarm. No alarm is generated
when only one beam is blocked by a small object.
Beam interruption time can be adjusted according to the peculiarities of each installation
site. When protecting a wall or fence, a long interruption time will catch intruders, but let
jumping cats pass through. This allows you to increase stability, while maintaining reliability
at every installation site.
Anti-Frost design incorporates special slots on the cover allowing beam passage even when
the cover is completely frosted over. The OPTEX casing design also reduces condensation
and water built-up, while sealed optics proved greater protection against dust and insects.
Easy Installation and Alignment
http://www.optexamerica.com/products/ax70t.htm (2 of 4) [06/08/2000 12:19:54]
AX-70T / AX-130T Specification Sheet
❍
❍
View Finder provides rough alignment, while voltage meter jacks allow fine tuning. Powerful
twin beams are sharply defined and will attain the optimum signal strength easily.
The pole mount brackets supplied will allow installation of two units on a pole at the same
height.
Model
Detection Method
Range
Maximum Arrival
Distance
Beam Characteristics
Interruption Period
AX-70T
Infrared Photoelectric
outdoor 70ft. (21m)
outdoor 130ft. (40m)
indoor 165ft. (50m)
indoor 330ft. (100m)
700ft. (210m)
1,300ft. (400m)
1,000pps. 8,800A pulsed infrared
50 to 500msec (variable)
Power Input
Current Draw
AX-130T
10 ~ 30VDC
30mA max (10 ~
30VDC)
http://www.optexamerica.com/products/ax70t.htm (3 of 4) [06/08/2000 12:19:54]
39mA max (10 ~
30VDC)
AX-70T / AX-130T Specification Sheet
Indicator
Transmitter-Green LED On in transmitting
condition.
Receiver-Red LED On in alarm condition.
Alarm Period
2 sec (±1) nominal
Alarm Output
N.C. 28VDC, 0.2A max
Tamper Switch
Opens when cover is removed.
Operating Temperature
-13°F to 131°F (-25°C to 55°C)
Environment Humidity
95% Max.
Alignment Angle
Mounting
Dimensions inches
(mm)
± 5° Vertical, ± 90° Horizontal
Wall or Pole
6.57"/H x 2.64"/W x 2.58"/D (167/H x 67/W x
66.5/D)
Weight
Standard Accessories
24.3oz (690g)
Screws (0.6" x 3/4" self tapping) x 4 Pole mount kit
*Specifications and design are subject to change without prior notice.
NOTE: This unit is designed to detect movement and activate an alarm control
panel. Being only part of a complete alarm system, we cannot assume
responsibility for theft or damages, should it occur.
http://www.optexamerica.com/products/ax70t.htm (4 of 4) [06/08/2000 12:19:54]
AX-100/200Plus & AX-100/200 Alpha Specification Sheet
Photoelectric Detectors Improved
with Optex Innovation to Provide
Advanced Performance in Outdoor
Detection
Optex Photoelectric Detectors with Innovative
Features for Easy Installation Provide Stable
Performance against False Alarms for More Effective
Outdoor Detection and Non-Securiy Applications
The Optex AX-100/200 Photoelectric Detector Series
is the next step in Outdoor Detection and will satisfy
all the needs of both users and installers. Optex
unique technology and design provide a wide range
of functions that greatly simplify installation and
maintain reliable performance even in many adverse
weather and environmental conditions.
STANDARD VERSION: AX-100/200 Plus
●
Quick Optical Alignment
❍
Alarm Indication LED in Viewfinder
The alarm condition is visually displayed using an alarm indication LED which is visible on
the front of the unit and can also be seen through a viewfinder.
http://www.optexamerica.com/products/ax100plus.htm (1 of 7) [06/08/2000 12:19:58]
AX-100/200Plus & AX-100/200 Alpha Specification Sheet
❍
❍
●
LED is On: Beam energy from the transmitter is not reaching the receiver.
LED is Off: Beam energy from transmitter is reaching the receiver.
Clear Viewfinder Visibility
A conveniently placed viewfinder allows for easy alignment even in some of the most
difficult mounting situations.
Fine Angle Adjustment for Alignment
The rotating dial allows the installer to finely adjust the beam easily either horizontally (180°
/ ±90°) or vertically (10° / ±5°) with or without the use of a screwdriver (finger adjustable).
Reliable Performance
❍
Lightning & Surge Protection
An improved EMI surge absorber and high surge resistiveness relay will maintain stable
operation even in the most lightning prone areas.
❍
Rain, Dust, and Insect Protection
The Rubber O-Ring and Rubber Grommets used in the AX-100/200Plus and Alpha Series
prevent rain, dust, and tiny insects from adversely affecting performance.
http://www.optexamerica.com/products/ax100plus.htm (2 of 7) [06/08/2000 12:19:58]
AX-100/200Plus & AX-100/200 Alpha Specification Sheet
❍
❍
❍
❍
❍
❍
Frost and Dew Protection
An anti-frost and convex visor design is incorporated to protect the detector from effect of
frost and dew.
High Grade Aspherical Lens
The high grade aspherical lens creates more sharply defined and precise infrared beams
compared to ordinary fresnel lenses.
Twin Synchronized Pulsed Beams Designed for Greater Stability
"And Gate" dual beams require simultaneous interruption ofboth beams to trigger an
activation. No activation is generated when a bird or falling leaves break just one beam.
99.5% Beam Blocking Stability
Enables stable operation with as much as 99.5% loss of beam energy caused by heavy rain,
dust storms, fog or snow.
A.G.C. (Automatic Gain Control) Circuit
The A.G.C. Circuit continually monitors for gradual changes in the signal's strength caused
by changing weather conditions. It adjusts the sensitivity accordingly to maintain the proper
signal level for the current environmental conditions.
Adjustable Beam Interruption Period
The Beam Interruption Time (the amount of time a beam must be broken for an alarm to
occur) can be adjusted to fit any application. For example, when protecting a wall or fence, a
longer interruption time will catch intruders, but let jumping cats pass through without setting
off an alarm.
http://www.optexamerica.com/products/ax100plus.htm (3 of 7) [06/08/2000 12:19:58]
AX-100/200Plus & AX-100/200 Alpha Specification Sheet
●
Design Durability
❍
❍
Highly Durable and Heat-Resisitant Housing Cover and Chassis
The housing cover and chassis provide higher durability against shocks, high temperatures,
and many other harsh environmental conditions.
Stainless Steel Screew & Back Plate
STANDARD VERSION: AX-100/200 Alpha
❍
Superior Version
■
■
3 Step LED Indicator for Fast and Accurate Fine Beam Alignment
The alignment condition is visually displayed on the front and in the
viewfinder of the receiver. Verification of alignment is achieved by using
the 3-step process shown below.
LED is On: Before Alignment
LED is Flickering: Beam energy from transmitter is reaching receiver
LED is Off: Ready for fine tuning
Selectable 4-Channel Beam Frequencies
The selectable beam frequencies can be used to avoid unwanted cross talk
that can occur when using multiple photobeams for long distance or beam
stacking applications.
http://www.optexamerica.com/products/ax100plus.htm (4 of 7) [06/08/2000 12:19:58]
AX-100/200Plus & AX-100/200 Alpha Specification Sheet
2 Beam Stacking
2 Beam Long Distance Stacking
http://www.optexamerica.com/products/ax100plus.htm (5 of 7) [06/08/2000 12:19:58]
AX-100/200Plus & AX-100/200 Alpha Specification Sheet
Model
Detection Method
AX-100Plus
AX-200Plus
AX-100Alpha
Infrared Photoelectric
AX-200Alpha
Outdoor
Indoor
Maximum Arrival Distance
100ft. (30m)
200ft. (60m)
200ft. (60m)
400ft. (120m)
200ft. (60m)
400ft. (120m)
Range
Beam Characteristics
Selectable Beam Frequency
Interruption Period
Power Input
Current Draw
(Transmitter+Receiver)
Alarm Period
Alarm Output
Tamper Switch
Operating Temperature
Environment Humidity
Alignment Angle
Mounting
100ft. (30m)
200ft. (60m)
1,000ft. (300m) 2,000ft. (600m) 1,000ft. (300m)
2,000ft. (600m)
Pulsed Infrared
4 channel
(Automatic synchronization)
50 ~ 500msec (Selectable)
10 ~ 28V DC
Normal operation 40mA
Normal operation 46mA max
During optical alignment 46mA max
2 sec (±1) nominal
Form C Relay (28V DC 0.2A max)
N.C. opens when cover is removed (Receiver Only)
-30°F ~ 131°F (-35°C ~ 55°C)
95% Max.
± 5° Vertical, ± 90° Horizontal
Wall or Pole
-
http://www.optexamerica.com/products/ax100plus.htm (6 of 7) [06/08/2000 12:19:59]
AX-100/200Plus & AX-100/200 Alpha Specification Sheet
Weight
36.7oz (1040g) (Both Transmitter and Receiver)
*Specifications and design are subject to change without prior notice.
NOTE: This unit is designed to detect an intruder and activate an alarm control panel.
Being only a part of a complete system, we cannot assume responsibility for theft or damages, should it
occur.
http://www.optexamerica.com/products/ax100plus.htm (7 of 7) [06/08/2000 12:19:59]
AX-250/500PLUS Specification Sheet
Innovative Design Meets
Unsurpassed Quality in
the New AX-250/500 Plus
The Photoelectric Beams of OPTEX's
AX-250/500PLUS Series combine precise
detection capability with increased reliability
providing superior outdoor detection.
A dual beam design incorporates synchronized pulsed
signals, and an adjustable beam interruption time can
virtually eliminate unwanted activation. A high level
of detection accuracy will be maintained, no matter
how harsh the environment.
The AX-250/500PLUS will automatically
compensate for changes in the surrounding
conditions. The advanced mechanical design allows
for easy installation and set-up providing long-term
reliability, ideal for today's outdoor security systems.
●
Lightning & Surge Protection
An improved EMI surge absorber and high surge resistiveness relay will maintain stable operation even
in the most lightning prone areas.
http://www.optexamerica.com/products/ax250plus.htm (1 of 4) [06/08/2000 12:20:01]
AX-250/500PLUS Specification Sheet
●
A.G.C. (Automatic Gain Control) Circuit
The A.G.C. Circuit continually monitors for gradual changes in the signal's strength caused by
changing weather conditions. It adjusts the sensitivity accordingly to maintain the proper signal level
for the current environmental conditions.
●
Reliability Chart for Outdoor Protection
Specially designed to eliminate various causes of outdoor false alarms.
False Alarm Causes
Lightning & High EMI
Disturbances
Insect Entering into Housing
Dew Condensation
Fog, Frost & Heavy Rain
Technology to Solve
High EMI Resistance
Sealed Enclosure Housing
High Sensitivity Tolerance
Excellent Optical Alignment
Environmental Analysis
Birds or Flying Objects
Size Analysis
AX Function & Features
High Surge Resistiveness
Relay & EMI Surge Absorber
IP54
Ultra High Power Transmitter
Anti-Frost Mechanism
Easy Optical Alignment
Mechanism
Automatic Gain Control
Twin Synchronized Pulsed
Beams
●
Adjustable Beam Interruption Period
Beam interruption time can be adjusted according to the peculiarities of each installation site. When
protecting a wall or fence, a long interruption time will catch intruders, but let jumping cats pass
through. Adjustable from 50 to 500msec.
●
Twin Synchronized Pulsed Beams Designed for Greater Stability
"And Gate" dual beams require simultaneous interruption of both beams to trigger an activation. No
activation is generated when a bird or falling leaves break just one beam.
●
99% Blocking Rate
Stable operation is maintained with as much as 99% of the beam's energy blocked by heavy rain, dust
storms, snow or fog.
●
Anti-Frost Design
●
Stainless Steel Screws & Back Plate
●
Knock-Outs for 1/2 Inch Conduit
●
Form C Relay Providing More Flexibility
●
Options
http://www.optexamerica.com/products/ax250plus.htm (2 of 4) [06/08/2000 12:20:01]
AX-250/500PLUS Specification Sheet
HU-1: Heating Unit
For use in cold areas. 24V DC/AC, 430mA max.
BC-1: Back Cover
Model
Detection Method
Range (Outdoor)
Maximum Arrival
Distance
Beam Characteristics
AX-250PLUS
AX-500PLUS
Infrared Photoelectric
250ft. (75m)
500ft. (150m)
2,500ft. (750m)
5,000ft. (1,500m)
Pulsed Infrared
http://www.optexamerica.com/products/ax250plus.htm (3 of 4) [06/08/2000 12:20:01]
AX-250/500PLUS Specification Sheet
Interruption period
Power Input
50 ~ 500msec (Selectable)
10.5 ~ 30VDC
Current Draw
(transmitter+receiver)
Normal operation
50 mA max
Alarm Period
2 sec (±1) nominal
Alarm Output
Form C Relay (28V DC 0.2A max)
N.C. opens when cover is removed (Receiver
Only)
Tamper Switch
Operating
Temperature
Environment Humidity
Alignment Angle
Mounting
Weight
-30°F ~ 131°F (-35°C ~ 55°C)
95% Max.
± 10° Vertical, ± 90° Horizontal
Wall or Pole
95.2 oz(2700g) (Both Transmitter and Receiver)
*Specifications and design are subject to change without prior notice.
NOTE: This unit is designed to detect an intruder and activate an alarm
control panel. Being only a part of a complete system, we cannot assume
responsibility for theft or damages, should it occur.
http://www.optexamerica.com/products/ax250plus.htm (4 of 4) [06/08/2000 12:20:01]
Vision
The Optex Vision Page has moved. If you are not automatically sent to the correct page, click here.
http://www.optexamerica.com/indexes/vant_index.htm [06/08/2000 12:20:01]
Vision Specifications Sheet
Vision
It's like having
FOUR systems in ONE!
'Turn on the security system'
Now it's as easy as A, B, C. Just select the area
you wish to secure and press 'On'. Vision, with its
'Point & Click' design, stands out as the easy to
understand, easy to use, security system.
To view a pdf of the product sheet,
click here.
QUAD KEY
Vision's Quad Key shows each part of the system and makes security as easy as A, B, C. Customers
understand Vision and appreciate its simplicity. Vision's Keep It Simple design makes it everyone's first
choice for security.
THREE ARMING METHODS
Select Mode, Zone Type, or Area Arming; it's your choice, whichever is best for your customer.
AREA ARMING
Zone Groups can arm & disarm together (like partitions). Area arming gives 'point & click' operation of up
to 4 preset arming configurations and eliminates the need for routine bypassing of windows or doors.
OUTDOOR ZONES
Outdoor detectors integrate directly to Vision, taking you beyond traditional 'interior-only' security
systems.
http://www.optexamerica.com/products/vision.htm (1 of 4) [06/08/2000 12:20:03]
Vision Specifications Sheet
Quad Key...for EZ partial Arming
Select the arming method which best suits the user's needs
- Area Arming, for Outside, Garage, Living Room
- Mode Arming, for Away, Home, Night
- Zone Type Arming, for Doors, Windows, Interior, Exterior
On Key for EZ Arm
Just select arming area(s) and press 'On' to arm. You can also arm the
entire system by pressing 'On' for two seconds
V-LCD1
Off Key for EZ Disarm
Pressing 'Off' silences the entry tone for 15 seconds, reducing
confusion and distraction during the disarming process..
Enter Code LED for EZ Operation
Lights when a User PIN is required to proceed.
V-LED1
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
PROGRAMMING POWER
4 built-in templates virtually eliminate programming.
Download quickly with virtually any modem.
Direct connect programming to on-site computer.
Field programmer holds up to 4 programs (optional).
Zones configure independently for greater flexibility.
SIA and Contact ID formats.
Installer's Walk-Test and Communicator Test.
ADVANCED PERFORMANCE
On-site serial printer interface.
Bell Circuit & Telephone Circuit Supervision.
100 event memory buffer.
3 programmable output terminals, with options that include Keyswitch Arming & Tamper Input.
Automatic Daylight Savings Time adjustment.
Double EOL Zone type
USER FRIENDLY OPTION
Exterior Zones integrate Outdoor Protection.
Night By-Pass Zones for easy 'at-home' arming.
Up-Arm to add more areas without disarming.
Quick Exit and Arm Without Delay options
Report-To-Pager reporting.
Personal Alarm Call reporting.
PGM Activation with or without PIN.
Annunciator Chime selectable by zone.
http://www.optexamerica.com/products/vision.htm (2 of 4) [06/08/2000 12:20:03]
Vision Specifications Sheet
ORDERING INFORMATION
V-CP1 LED*
Includes control panel, cabinet, and LED keypad.
V-CP1 LCD*
Includes control panel, cabinet, and LCD keypad.
V-LED1*
LED keypad for Vision control
V-LCD1*
LCD keypad for Vision control
V-RPU DOS
Remote Programming Utility (DOS)
V-RPU WIN
Remote Programming Utility (Windows)
* add (S) after part number for Spanish version
SPECIFICATIONS:
Hardware (V-PCB1/V-LED&V-LCD)
Power
Outputs
Auxiliary Power
Bell/Siren
Programmable*
16.5V AC
12V DC, Total 1A
* Each programmable output cannot exceed 50mA
Number of Keypads
Dimensions/Current Draw
V-LED 1 Keypad
V-LCD 1 Keypad
V-PCB 1 Main Board
Serial Port
Max 4 units per system
W x H x T mm/mA
147 x 84 x 22mm/65mA
147 x 120 x 22mm/65mA
191 x 73mm/100mA
Serial Printer, DPU or RPU
PIN Codes
User codes
8*
* User #08 can be programmed as a temporary PIN Code
Utility code
Installer code
Duress code
Call RPU code
1
1
1
1
Zones & Programmable In/Out
Number of Zones
Programmable In/Out*
Total 8
Main board: 6
Keypad: 2
1 Input + 2 Outputs or 3 Outputs
* 1 output can be programmed as 2 wire smoke detector
http://www.optexamerica.com/products/vision.htm (3 of 4) [06/08/2000 12:20:03]
Vision Specifications Sheet
http://www.optexamerica.com/products/vision.htm (4 of 4) [06/08/2000 12:20:03]
It’s like having
FOUR systems in ONE!
V-LED 1
V-LCD 1
‘Turn on the security system’
Now it’s as easy as A, B, C. Just select the area you wish to secure and press ‘On’. Vision, with its ‘Point & Click’ design,
stands out as the easy to understand, easy to use, security system.
QUAD KEY
AREA ARMING
Vision’s Quad Key shows each part of the system and makes
security as easy as A, B, C. Customers understand Vision
and appreciate its simplicity. Vision’s Keep It Simple design
makes it everyone’s first choice for security.
Zone Groups can arm & disarm together (like partitions). Area
arming gives ‘point & click’ operation of up to 4 preset arming
configurations and eliminates the need for routine bypassing
of windows or doors.
THREE ARMING METHODS
OUTDOOR ZONES
Select Mode, Zone Type, or Area Arming; it’s your choice,
whichever is best for your customer.
Outdoor detectors integrate directly to Vision, taking you
beyond traditional ‘interior-only’ security systems.
8 Zone Security Control System
Quad Key...for EZ partial Arming
Select the arming method which best suits the user’s needs:
- Area Arming, for Outside, Garage, Living Room
- Mode Arming, for Away, Home, Night
- Zone Type Arming, for Doors, Windows, Interior, Exterior
Ready
Trouble
Chime
A
B
DOORS
WINDOWS
INTERIOR
EXTERIOR
C
1Ready
Test
2
Memory
Fire ACTrouble
3
4
Bypass
5
6
Memory Bypass
D
1
7
2
Enter Code
ON
Reset
Trouble
Enter
3
OFF
4
Program
5
A
DOORS
Utility
INTERIOR
8
9
Quick
7
Clear
0
#
6
8
C
B
WINDOWS
Chime
Reset
1
2
3
Memory
Trouble
Bypass
4
EXTERIOR
D
6
7
8
9
Quick
Clear
0
#
OFF
On Key for EZ Arm
Just select arming area(s) and press ‘On’ to arm. You can also arm the entire
system by pressing ‘On’ for two seconds
Utility
Enter
Enter Code
ON
5
Program
Test
Off Key for EZ Disarm
Pressing ‘Off’ silences the entry tone for 15 seconds, reducing confusion and
distraction during the disarming process..
Enter Code LED for EZ Operation
Lights when a User PIN is required to proceed.
V-LCD1
V-LED1
Programming Power
♦
♦
♦
♦
♦
♦
♦
Advanced Performance
4 built-in templates virtually eliminate programming.
Download quickly with virtually any modem.
Direct connect programming to on-site computer.
Field programmer holds up to 4 programs (optional).
Zones configure independently for greater flexibility.
SIA and Contact ID formats.
Installer’s Walk-Test and Communicator Test.
♦
♦
♦
♦
♦
♦
On-site serial printer interface.
Bell Circuit & Telephone Circuit Supervision.
100 event memory buffer.
3 programmable output terminals, with options that include
Keyswitch Arming & Tamper Input.
Automatic Daylight Savings Time adjustment.
Double EOL Zone type
User Friendly Options
Ordering Information:
Exterior Zones integrate Outdoor Protection.
♦ Night By-Pass Zones for easy ‘at-home’ arming.
♦ Up-Arm to add more areas without disarming.
♦ Quick Exit and Arm Without Delay options
♦ Report-To-Pager reporting.
♦ Personal Alarm Call reporting.
♦ PGM Activation with or without PIN.
♦ Annunciator Chime selectable by zone.
V-CP1 LED*
Includes control panel, cabinet, and LED keypad.
V-CP1 LCD*
Includes control panel, cabinet, and LCD keypad.
V-LED1*
LED keypad for Vision control
V-LCD1*
LCD Keypad for Vision control
V-RPU DOS
Remote Programming Utility (DOS)
V-RPU WIN
Remote Programming Utility (Windows)
* add (S) after part number for Spanish version
♦
Specifications
Hardware ( V-PCB1/V-LED&V-LCD )
PIN Codes
16.5V AC
User codes
8*
*User #08 can be programmed as a temporary PIN code
V-CP
1
1
1
1
k
Lin
Number of Zones
Total 8
Main board
6
Keypad
2
Programmable In/Out* 1 Input+2 Outputs or 3 Outputs
Data Link
ta
Da
Zones & Programmable In/Out
Telephone Line
Data Link
*Each programmable ouput cannot exceed 50mA
Number of Keypads
Max. 4 units per system
Dimensions/Current Draw
W × H × T mm/mA
V-LED 1 Keypad
147 × 84 × 22mm/55mA
V-LCD 1 Keypad
147 ×120 × 22mm/65mA
V-PCB 1 Main Board
191 × 73mm/100mA
Serial port
Serial printer, DPU or RPU
Utility code
Installer code
Duress code
Call RPU code
Lin
k(
On
ew
ay
)
12V DC, Total 1A
Da
ta
Power
Outputs
Auxiliary Power
Bell/Siren
Programmable*
Modem
Personal
Computer
Serial Printer
*1 output can be programmed as 2 wire smoke detector
Direct
Programming
Utility
OPTEX INCORPORATED
1845 W. 205th St. Torrance, Ca. 90501-1510 U.S.A.
TEL(310)533-1500 TOLL FREE (800) 966-7839 FAX(310)533-5910
OPTEX CO., LTD. (ISO 9001 Certified by LRQA)
4-7-5 Nionohama Otsu, 520-0801 Japan
TEL(077)524-6047 FAX(077)522-9022
OPTEX (EUROPE) LTD. (ISO 9002 Certified by NQA)
Clivemont Road, Cordwallis Park, Maidenhead, Berkshire, SL6 7BU U.K.
TEL(01628)631000 FAX(01628)636311
No. 75046-00-5130-0002
Automatic Door Access Control - Index
OA-50C
OA-60C
OA-201C
OA-202C
OP-03 Series
OP-08
OS-1C /
OS-2C
HA-6000T/S
http://www.optexamerica.com/indexes/door_index.htm [06/08/2000 12:20:09]
OA-601C
OA-50C Specifications Sheet
Innovative Technology for
Safe, Reliable Motion and
Presence Detection
SAFETY: The OPTEX OA-50C combines two
different methods of detection (motion and presence)
to assure safe and sure operation for both moving
and/or stationary people and objects.
RELIABILITY: The OA-50C provides
super-dependable, low maintenance operation all year
round. Innovative active infrared technology will
sense both motion and presence, even in extremely
harsh environments, without false operation.
●
Combining Motion and Presence Detection
For safe, reliable and economical operation, the OA-50C's presence sensor will hold doors open for a
selected 2, 7 or 15 second time period when any non-moving object is within its detection area. When
the selected time expires and no further movement is detected, the doors are released. However, when
people simply travel through the detection area, the doors are released as soon as they have safely
exited the area.
http://www.optexamerica.com/products/oa50c.htm (1 of 4) [06/08/2000 12:20:12]
OA-50C Specifications Sheet
●
Environmental Disturbance Immunity
●
Reliable 9 Zone Detection Area
●
Right and Left Area Angle Adjustments
●
Detects Humans as Well as Objects
●
Compact, High Tech Design Fits Any Installation
●
Meets ANSI Standards
Click Here To See The OA-50C's
Detection Area and How To Adjust It
http://www.optexamerica.com/products/oa50c.htm (2 of 4) [06/08/2000 12:20:12]
OA-50C Specifications Sheet
Model
Detection Range
Detection Area
Detection Method
Depth Area
Variable Range
Width Area
Variable Range
Power Input
Current Draw
Power/Operating Indicator
Output Contact
Output Hold
Operating Temperature
Weight
Accessories
OA-50CB/OA-50CS/OA-50CW
2.0m(6.6ft) ~ 2.7m(8.9ft) Max.
See the chart
Near Infrared Reflection Method
7.5° ~ 23.5° = 16°(4° x 4steps)
Adjustable
-8° ~ +8° = 16°(4° x 4 steps)
Adjustable
12 ~ 24V AC/DC
200mA Max. (at 12V AC)
LED ON (Stand by)
LED OFF (When detecting)
N.O. Relay 50V 0.3A (Resistance Load)
0.5sec. Delay
-20°C ~ +55°C (-4°F ~ +131°F)
190g (6.7oz)
2m(6.6ft) Wire with plug,
2 Mounting Screw,
Mounting Template
*Specifications subject to change without prior notice.
http://www.optexamerica.com/products/oa50c.htm (3 of 4) [06/08/2000 12:20:12]
OA-50C Specifications Sheet
http://www.optexamerica.com/products/oa50c.htm (4 of 4) [06/08/2000 12:20:12]
OA-50C Detection Areas
EXTREMELY DENSE AND FLEXIBLE DETECTION AREA
The OA-50C's detection area consists of 9 solid outer zones, assuring safe and
reliable operation even when environmental conditions, such as rain and snow,
are present.
ADJUSTING THE DETECTION AREA
Area Depth Adjustment
http://www.optexamerica.com/products/oa50darea.htm (1 of 4) [06/08/2000 12:20:15]
OA-50C Detection Areas
The area depth can be adjusted in 4 steps (7.5° to 23.5°)
Area Width Adjustment
http://www.optexamerica.com/products/oa50darea.htm (2 of 4) [06/08/2000 12:20:15]
OA-50C Detection Areas
Area Width Elimination: Areas 1,2,3 or 7,8,9 can be easily eliminated,
allowing the OA-50C to work in various installation applications, i.e. single leaf
doors, double doors, and when miscellaneous objects such as plants, etc. are
within the area.
Right and Left Angle Adjustment
The width of the detection area can be also adjusted to the right and the left 8°
(4° x 2 steps) to compensate for obstacles within the detection area.
http://www.optexamerica.com/products/oa50darea.htm (3 of 4) [06/08/2000 12:20:15]
OA-50C Detection Areas
http://www.optexamerica.com/products/oa50darea.htm (4 of 4) [06/08/2000 12:20:15]
OA-60C Specifications Sheet
Ceiling Mount, Recessed
Sensor With Safe And
Reliable Presence
Detection
The OA-60C is a recessed, ceiling mounted sensor
for automatic doors which provides a high level of
safety. Its wide detection range and presence sensing
capabilities make this unit flexible enough to adjust
to almost any installation.
●
Presence Detection With Complete Area Coverage
For safe operation, the OA-60C's presence sensor will hold doors open for a selected 2, 15, or 60
second time period when any non-moving person or object is with the detection area. And the flexible
detection area adjustment provides no undetected area just behind the doors.
http://www.optexamerica.com/products/oa60c.htm (1 of 3) [06/08/2000 12:20:17]
OA-60C Specifications Sheet
●
Dense Yet Flexible Detection Area
The OA-60C's detection area consists of 18 individual detection zones which can be adjusted to obtain
the desired detection area.
●
Environmental Disturbance Immunity
The OA-60C provides extremely dependable, low maintenance operation all year round. Presence
Detection achieved with innovative Active Infrared Technology. This advanced design allows the unit
to operate reliably even in harsh environments.
●
Attractive Designed to Suite Any Installation Decor
Slim projection of only 15mm (0.59 inches)
●
12 - 24V AC/DC Universal Power Input
Click Here To See The OA-60C's
Detection Area and How To Adjust It
http://www.optexamerica.com/products/oa60c.htm (2 of 3) [06/08/2000 12:20:17]
OA-60C Specifications Sheet
Model
Detection Range
Detection Area
Detection Method
Depth Area
Variable Range
Power Input
Current Draw
Power/Operating Indicator
Output Contact
Output Hold
Operating Temperature
Weight
Accessories
OA-60C
2.0m(6.6ft) ~ 4.0m(13.1ft) Max.
See chart
Near Infrared Reflection Method
Inner Area: approx 0 ~ 18°
Approach Area: approx 0 ~ 26°
12 ~ 24V AC/DC
300mA Max. (at 24V AC)
LED ON in stand by
LED OFF when detecting
N.O. Relay 50V 0.1A (Resistance Load)
0.5 sec. Delay
-20°C ~ +55°C (-4°F ~ +131°F)
430g (15.2oz)
3m Wire with plug, 2 Mounting Screws,
Mounting Template, Area Masking Seals
*Specifications subject to change without prior notice.
http://www.optexamerica.com/products/oa60c.htm (3 of 3) [06/08/2000 12:20:17]
OA-60C Detection Areas
DENSE YET FLEXIBLE DETECTION AREA
Mounting
a
b
Height m(ft)
2.5
0~800
0~1300
(8.2)
(0~31 1/2) (0~51 3/16)
3
0~1000
0~1500
(9.8)
(0~39 3/8) (0~59 1/16)
0~1900
4
0~1300
(0~74
(13.1)
(0~51 3/16)
13/16)
c
d
e
f
480
(18 7/8)
580
(22 7/8)
1800
(70 7/8)
2180
(85 7/8)
80
(3 1/8)
100
(3 15/16)
230
(9 1/16)
280
(11 1/16)
770
(30 5/16)
2900
(114 3/16)
120
(4 3/4)
370
(14 9/16)
mm (inches)
ADJUSTING THE DETECTION AREA
http://www.optexamerica.com/products/oa60darea.htm (1 of 3) [06/08/2000 12:20:19]
OA-60C Detection Areas
Area Depth Adjustment
Both of inner area and approach area can be adjusted independently by Area Depth Adjuster.
Inner Area: 0° ~ 18° = 2° x 9 steps; Approach Area: 0° ~ 26° = 2° x 13 steps
Area Width Adjustment
http://www.optexamerica.com/products/oa60darea.htm (2 of 3) [06/08/2000 12:20:19]
OA-60C Detection Areas
Areas A,B,C, and D can be easily eliminated by Area Masking Seals, allowing the OA-60C to work in
various installation applications i.e. single leaf doors, double doors, and when miscellaneous objects such as
plants, etc. are withinthe area.
http://www.optexamerica.com/products/oa60darea.htm (3 of 3) [06/08/2000 12:20:19]
Factory Automation - Index
BGS Series
C Series
J Series
K Series
JRF Series
JRF-T Series
R Series
S Series
X-400, 5140,
VF-Series
Thermo-Hunters
Thermo-Hunter
PT-3LF
Thermo-Hunter
BUILT-IN2
V Series
V2 Series
http://www.optexamerica.com/indexes/factauto.htm [06/08/2000 12:24:09]
Under Construction!
This section of the website
is under construction!
Please come back soon for more info.
http://www.optexamerica.com/indexes/comingsoon.htm [06/08/2000 12:24:10]
About The Company
Meeting the Needs of our Modern World
Through Sensing Technology
Optex America Inc.
Corporate Headquarters
1845 West 205th St., Torrance, CA 90501
Phone: 800-966-7839 + Fax: 310-533-5910
Optex, America markets products manufactured by Optex Company Limited of
Otsu, Japan throughout the continents of North and South America. We specialize
in passive and active infrared technology, control systems, and CCTV products
which are applied in the fields of Security, Automatic Door Controls, and Factory
Automation.
Since its founding in 1979, Optex has established a world-wide reputation for
quality, innovation, and technical excellence. Our products always represent an
investment in performance and long term satisfaction.
http://www.optexamerica.com/indexes/about.htm (1 of 2) [06/08/2000 12:24:12]
About The Company
Click Here To Locate A
Sales Rep In Your Area
http://www.optexamerica.com/indexes/about.htm (2 of 2) [06/08/2000 12:24:12]
Click Here To Locate An
Optex Employee
Locate The Sales Representative In Your Area
[FOR CANADA: CLICK HERE]
Click On The State In Which You Are Located
To Find The Sales Representative For Your Area
http://www.optexamerica.com/indexes/usamap.htm [06/08/2000 12:24:14]
Sales Representatives in Canada
The Sales Representatives For Canada are:
Name: Jay Vaare-Lamoureux
Title: Canadian Regional Sales Manager
Phone Number: (800) 966-7839
Fax Number: (310) 533-5910
Return To Previous Page
http://www.optexamerica.com/sales_reps/cansalesrep.htm [06/08/2000 12:24:15]
Sales Representatives in the Western Region
The Sales Representatives For This Section of the United States are:
SECURITY
Name: Griff Kimble
Title: Western Regional Sales Manager
Phone Number: (800) 966-7839
Fax Number: (310) 533-5910
AUTOMATIC DOOR
Name: Kevin Rogers
Title: Western Regional Sales Manager,
Automatic Door Division
Phone Number: (800) 966-7839
Fax Number: (310) 533-5910
FACTORY AUTOMATION
http://www.optexamerica.com/sales_reps/west.htm (1 of 2) [06/08/2000 12:24:17]
Sales Representatives in the Western Region
PHOTOELECTRIC SENSORS
8651 Buffalo Avenue, Niagara Falls, New York 14304
Phone Number: (716) 283-1461 or Toll Free 1-800-644-1756
Fax Number: (716) 283-2127
Website: http://www.htm-optex.com
Contact: Art Ramsay
THERMOMETER
P.O. Box 398, Pleasanton, California 94566
Phone Number: (510) 426-3011 Ext. 20 or Toll Free 800-962-6776
Fax Number: (510) 846-1147
Contact: Fredrick L. Wu
Return To Previous Page
http://www.optexamerica.com/sales_reps/west.htm (2 of 2) [06/08/2000 12:24:17]
Sales Representatives in the South Central Region
The Sales Representative For This Section of the United States is:
SECURITY
Name: Keith Daulton
Phone Number: (800) 966-7839 Ext. 205
Fax Number: (310) 533-5910
E-mail Address: kdaulton@optexamerica.com
AUTOMATIC DOOR
Name: Kevin Rogers
Title: Western Regional Sales Manager,
Automatic Door Division
Phone Number: (800) 966-7839
Fax Number: (310) 533-5910
FACTORY AUTOMATION
http://www.optexamerica.com/sales_reps/southcental.htm (1 of 2) [06/08/2000 12:24:18]
Sales Representatives in the South Central Region
PHOTOELECTRIC SENSORS
8651 Buffalo Avenue, Niagara Falls, New York 14304
Phone Number: (716) 283-1461 or Toll Free 1-800-644-1756
Fax Number: (716) 283-2127
Website: http://www.htm-optex.com
Contact: Art Ramsay
THERMOMETER
P.O. Box 398, Pleasanton, California 94566
Phone Number: (510) 426-3011 Ext. 20 or Toll Free 800-962-6776
Fax Number: (510) 846-1147
Contact: Fredrick L. Wu
Return To Previous Page
http://www.optexamerica.com/sales_reps/southcental.htm (2 of 2) [06/08/2000 12:24:18]
Sales Representatives in the Southeast Region
The Sales Representatives For This Section of the United States are:
SENSORS
3565 Hutchinson Road, Suite 400, Cumming, GA 30040
Phone Number: (770) 887-2844 . Toll Free: (800) 333-2844 . Fax Number: (770) 889-7431
WWW Home Page: http://www.SecuritySolutions-ga.com
E-Mail Address: SecuritySolutions@worldnet.att.net
Outside Sales Staff:
Management - Gust Askounis, President & Ben Jackson, Vice President of Sales
Florida Sales Manager - Jack Green (States covered: FL)
Mid Atlantic Sales Manager - Lise Carper (States covered: VA, WV, MD, DE, DC, PA)
Mid South Sales Manager - Rod Warren (States covered: GA, AL, MS, NC, SC, TN)
Inside Sales and Administrative Support:
Cindy Askounis - Vice President, Business Development
Amy Drews - Executive Assistant, Business Development
Joyce DiVirgilius - Executive Assistant, Sales
Maureen Starks - Senior Account Manager: GA, NC, and SC and outside sales for PR
Connie Haman - Senior Account Manager: FL, AL, MS, TN
Maria Rovinelli - Senior Account Manager: WV, VA, MD, DE, DC, PA
AUTOMATIC DOOR
http://www.optexamerica.com/sales_reps/southeast.htm (1 of 3) [06/08/2000 12:24:20]
Sales Representatives in the Southeast Region
Name: Joe Agabiti
Phone Number: (800) 966-7839
Fax Number: (310) 533-5910
E-mail Address: jagabiti@optexamerica.com
CONTROL PANELS
Name: Jay Kessel
Phone Number: (310) 533-1500 Ext. 101
Fax Number: (310) 533-5910
E-mail Address: jkessel@optexamerica.com
FACTORY AUTOMATION
PHOTOELECTRIC SENSORS
8651 Buffalo Avenue, Niagara Falls, New York 14304
Phone Number: (716) 283-1461 or Toll Free 1-800-644-1756
Fax Number: (716) 283-2127
Website: http://www.htm-optex.com
Contact: Art Ramsay
THERMOMETER
http://www.optexamerica.com/sales_reps/southeast.htm (2 of 3) [06/08/2000 12:24:20]
Sales Representatives in the Southeast Region
P.O. Box 398, Pleasanton, California 94566
Phone Number: (510) 426-3011 Ext. 20 or Toll Free 800-962-6776
Fax Number: (510) 846-1147
Contact: Fredrick L. Wu
Return To Previous Page
http://www.optexamerica.com/sales_reps/southeast.htm (3 of 3) [06/08/2000 12:24:20]
Sales Representatives in the Northeast Region
The Sales Representatives For This Section of the United States are:
SENSORS
Phone Number: 800-662-9178
Fax Number: 508-880-0932
E-mail Address: tmgmtgroup@aol.com
AUTOMATIC DOOR
Name: Joe Agabiti
Phone Number: (800) 966-7839
Fax Number: (310) 533-5910
E-mail Address: jagabiti@optexamerica.com
CONTROL PANELS
http://www.optexamerica.com/sales_reps/northeast.htm (1 of 2) [06/08/2000 12:24:21]
Sales Representatives in the Northeast Region
Name: Jay Kessel
Phone Number: (310) 533-1500 Ext. 101
Fax Number: (310) 533-5910
E-mail Address: jkessel@optexamerica.com
FACTORY AUTOMATION
PHOTOELECTRIC SENSORS
8651 Buffalo Avenue, Niagara Falls, New York 14304
Phone Number: (716) 283-1461 or Toll Free 1-800-644-1756
Fax Number: (716) 283-2127
Website: http://www.htm-optex.com
Contact: Art Ramsay
THERMOMETER
P.O. Box 398, Pleasanton, California 94566
Phone Number: (510) 426-3011 Ext. 20 or Toll Free 800-962-6776
Fax Number: (510) 846-1147
Contact: Fredrick L. Wu
Return To Previous Page
http://www.optexamerica.com/sales_reps/northeast.htm (2 of 2) [06/08/2000 12:24:21]
Sales Representatives in the North Central Region
The Sales Representative For This Section of the United States is:
SECURITY / AUTOMATIC DOOR
Name: Jay Kessel
Phone Number: (310) 533-1500 Ext. 101
Fax Number: (310) 533-5910
E-mail Address: jkessel@optexamerica.com
FACTORY AUTOMATION
PHOTOELECTRIC SENSORS
8651 Buffalo Avenue, Niagara Falls, New York 14304
Phone Number: (716) 283-1461 or Toll Free 1-800-644-1756
Fax Number: (716) 283-2127
Website: http://www.htm-optex.com
Contact: Art Ramsay
THERMOMETER
http://www.optexamerica.com/sales_reps/northcentral1.htm (1 of 2) [06/08/2000 12:24:23]
Sales Representatives in the North Central Region
P.O. Box 398, Pleasanton, California 94566
Phone Number: (510) 426-3011 Ext. 20 or Toll Free 800-962-6776
Fax Number: (510) 846-1147
Contact: Fredrick L. Wu
Return To Previous Page
http://www.optexamerica.com/sales_reps/northcentral1.htm (2 of 2) [06/08/2000 12:24:23]
Sales Representatives in the North Central Region
The Sales Representative For This Section of the United States is:
SECURITY / AUTOMATIC DOOR
Name: Michael Skjerven
Phone Number: (800) 966-7839
Fax Number: (310) 533-5910
E-mail Address: mskjerven@optexamerica.com
FACTORY AUTOMATION
PHOTOELECTRIC SENSORS
8651 Buffalo Avenue, Niagara Falls, New York 14304
Phone Number: (716) 283-1461 or Toll Free 1-800-644-1756
Fax Number: (716) 283-2127
Website: http://www.htm-optex.com
Contact: Art Ramsay
THERMOMETER
http://www.optexamerica.com/sales_reps/northcentral2.htm (1 of 2) [06/08/2000 12:24:23]
Sales Representatives in the North Central Region
P.O. Box 398, Pleasanton, California 94566
Phone Number: (510) 426-3011 Ext. 20 or Toll Free 800-962-6776
Fax Number: (510) 846-1147
Contact: Fredrick L. Wu
Return To Previous Page
http://www.optexamerica.com/sales_reps/northcentral2.htm (2 of 2) [06/08/2000 12:24:23]
Contact An Optex Employee
Find by Division/Department:
Show Employees
Find by Employee Name:
Show Info
Show All Optex Employees
Return To About Optex Page
http://www.optexamerica.com/employees/findemployee2.cfm [06/08/2000 12:24:24]
C Series Specification Sheet
Vibration Resistance With
Full Injection of Epoxy
Inside the Metal-Armed
Body, Being Even Strong
to Environmental Noise
M8 connector type are also available
for full range of products.
1500cm
300cm
Through-Beam Type
Retro-Reflection Type
100cm
Retro-Polarizing Type
11cm
Diffused Reflector Type
Diffused Reflection Type
(long range detection)
40cm
●
Durable Metallic Body
Vastly superior to plastic bodies in terms of durability and resistance to chemicals. Can be used in severe
conditions, and the screw thread is unlikely to be damaged in installation.
●
Plug-In Connector
http://www.optexamerica.com/products/cseries.htm (1 of 5) [06/08/2000 12:24:27]
C Series Specification Sheet
It has greatly simplified the installation procedure. Maintenance after the switch has been installed is
simple.
●
All Models Fitted with a Sensitivity Adjuster (DC)
All models are fitted with a sensitivity adjuster. Sensitivity can be adjusted according to sensing
conditions, and the switch can quickly be adjusted for sensing different kinds of objects.
●
15m Long-Distance Sensing (Through-Beam Type):
The through-beam type has a sensing range of 15m, and the retro-reflection type has a sensing range of
3m, both of which surpass the conventional standards. Outstandingly stable, even for sensing minute
objects.
●
Detects mirror-like and shiny surfaces CRD(A)F retro-reflection type with built-in polarizing filter
●
External diagnosis TEST INPUT function (Only on emitter of CTD-1500 through-beam type)
When the white lead line of the emitter is connected to 0V, a interrupted state is created electrically.
http://www.optexamerica.com/products/cseries.htm (2 of 5) [06/08/2000 12:24:27]
C Series Specification Sheet
●
Typical Uses
Lenthwise Positioning
Through-Beam Type CTD-1500(C)(N,P)
Sensing the position of food packages
Diffused Reflection Type CDD-11(C)(N,P)
●
Water-Proof to IP66 (IEC144)
Vibration-Resistance also vastly increased
●
2 Types: L/ON D/ON
Control Output
●
Built-In short-circuit protection
●
Beam axis can be bent 90° with a side-on attachment (optional)
- Type T000 for CTD-1500, CRD-300, CRDF-100
- Type T110 for CDD-11
- Type T400 for CDD-40
●
Straight and L-Shaped Connectors as Options
- CCN-S = Standard Straight Model
- CCN-L = L-Shaped Model
●
Sensor Models
Model
Type
Through-Beam Type [15m]
Direct Cording
CTD-1500
Plug-in
connector
Retro-Reflection Type [3m]
Direct Cording
CRD-300
Plug-in
connector
Retro-Reflection Type [1m]
(with built-in polarizing filter)
Direct Cording
CRDF-100
Plug-in
connector
Output
NPN
Model Number
CTD-1500N
PNP
NPN
CTD-1500P
CTD-1500CN
PNP
NPN
CTD-1500CP
CRD-300N
PNP
NPN
CRD-300P
CRD-300CN
PNP
NPN
CRD-300CP
CRDF-100N
PNP
NPN
CRDF-100P
CRDF-100CN
PNP
CRDF-100CP
http://www.optexamerica.com/products/cseries.htm (3 of 5) [06/08/2000 12:24:27]
C Series Specification Sheet
Diffused Reflection Type [11cm] Direct Cording
CDD-11
Plug-in
connector
Diffused Reflection Type [40cm] Direct Cording
(long range detection)
CDD-40
Plug-in
connector
NPN
CDD-11N
PNP
NPN
CDD-11P
CDD-11CN
PNP
NPN
CDD-11CP
CDD-40N
PNP
NPN
CDD-40P
CDD-40CN
PNP
CDD-40CP
Click Here To See The
C-Series Dimensions
Model
Detecting
Distance
Supply Voltage
Power
Consumption
Diffused
Retro-Reflection
Through-Beam Retro-Reflection
Diffused
Reflector Type
Type (with built-in
Type
Type
Reflector Type (long range
polarizing filter)
detection)
CTD-1500
CRD-300
CRDF-100
CDD-11
CDD-40
11cm(20cm
15m
0.05~3m
0.05~1m
40cm
mat white
paper)
DC12 ~ 24V ± 20%
40mA
30mA
Semi-transparent
Opaque Object Opaque Object
Detecting Object
objects and mirror15mm min.
45mm min.
surfaced objects
Response Time
Hysteresis
Light Source
Sensitivity
Adjustment
Indicator
Transparent
and Opaque
Objects
Transparent
and Opaque
Objects
10% max.
10% max.
1.5 msec. max.
-
Infrared LED (except CRDF-100 with Red LED)
Single Turn Adjuster
Sensor Indicator (red LED) (power indicator on the through-beam type emitter)
Control Output
NPN or PNP open collector MAX 100mA DC30V residual voltage 1V max.
Operation Mode
LIGHT ON / DARK ON slected by control wiring
Connection
2m cable 4 x 0.3mm2 PVC ø5/M12 x 4 plug-in connector
http://www.optexamerica.com/products/cseries.htm (4 of 5) [06/08/2000 12:24:27]
C Series Specification Sheet
Noise Resistance
(power line
noise)
Insulation
Resistance
Ambient
Temperature
Ambient
Humidity
Ambient
Operating
Illumination
Vibration
Resistance
1,000Vp pulse 1µsec width (on noise simulator)
20M min. (DC 500V)
-25 ~ 55°C
35 ~ 85% RH
Sunlight; 10,000 lux max., Halogen light; 3,000 lux max.
10-55Hz Amplitude 1.5mm 2 hours in each XYZ directions
Shock Resistance
500 m/s2 (approx. 50G) 3 times in each of XYZ directions
Protection
IEC standard IP66 (water resistant model)
Category
Enclosure
Case; BSBM + Ni Lens; PC
Materials
Weight
Approx. 40g
Approx. 40g
(excluding cord
for emitters
and nuts)
and receivers
http://www.optexamerica.com/products/cseries.htm (5 of 5) [06/08/2000 12:24:27]
C-Series Dimensions
http://www.optexamerica.com/products/cseriesdim.htm (1 of 2) [06/08/2000 12:24:29]
C-Series Dimensions
http://www.optexamerica.com/products/cseriesdim.htm (2 of 2) [06/08/2000 12:24:29]
Request For Information Form
First Name
Last Name
Company
Joshua
Phone
Sterling
Optex
Fax
Address
City
State
E-Mail (Required)
Zip
jsterling@optexamerica.com
Country
Select The Products You Would Like Information On:
Passive Infrared
Outdoor Sensors:
LX-40 / 80N
VX-40 / 40A
All of the Above
Control
Panels:
Genesys 824 Alpha
Genesys 824R
Genesys 824 Alpha Fire
MDC
Super MDC
Vision
All of the Above
Passive Infrared
Indoor Sensors:
CX-50 / 50 AM
CX-70M
EX-35
FX-40
FX-360
RX-40PI
RX-F30
SX-45C / SX-75C
SX-360Z
All of the Above
Misc. /
Accessories:
AX-BT
BC-1
CA-1W
CA-2C
EA-1W
FA-1W
FA-2C
FR-100
HU-1
LS-360S
http://www.optexamerica.com/moreinfo.cfm (1 of 2) [06/08/2000 12:24:32]
Photoelectric
Detectors:
AX-70T / AX-130T
AX-100S / AX-100SR
AX-100 / 200 Plus
AX-100 / 200 Alpha
AX-250 / 500 Plus
AX-350 / 650 MKII
OS-1C / OS-2C
All of the Above
Automatic Door
Access Control:
OA-50C
OA-60C
OA-201C
OA-202C
OA-601C
OP-03 Series
OP-08
OS-1C / OS-2C
HA-6000T/S
All of the Above
Request For Information Form
SMA-45
All of the Above
Home and
Office Automation:
Factory
Automation:
Wireless 1000
LX-40/80N
VX-40/40A
BGS Series
C Series
J Series
JRF Series
JRF-T Series
K Series
R Series
S Series
Thermo-Hunter PT-3LF
Thermo-Hunter BUILT-IN2
X-400, 5140, VF- Series
Thermo-Hunters
V Series
V2 Series
All of The Above
How would like to receive this information?
-
Additional Comments:
Send This Form
Clear Form And Start Over
http://www.optexamerica.com/moreinfo.cfm (2 of 2) [06/08/2000 12:24:32]
Request For Information Form
First Name
Phone
Last Name
Company
Fax
Address
City
State
E-Mail (Required)
Zip
Country
Select The Products You Would Like Information On:
Passive Infrared
Outdoor Sensors:
LX-40 / 80N
VX-40 / 40A
All of the Above
Control
Panels:
Genesys 824 Alpha
Genesys 824R
Genesys 824 Alpha Fire
MDC
Super MDC
Vision
All of the Above
Passive Infrared
Indoor Sensors:
CX-50 / 50 AM
CX-70M
EX-35
FX-40
FX-360
RX-40PI
RX-F30
SX-45C / SX-75C
SX-360Z
All of the Above
Misc. /
Accessories:
AX-BT
BC-1
CA-1W
CA-2C
EA-1W
FA-1W
FA-2C
FR-100
HU-1
LS-360S
http://www.optexamerica.com/moreinfonew.cfm (1 of 2) [06/08/2000 12:24:34]
Photoelectric
Detectors:
AX-70T / AX-130T
AX-100S / AX-100SR
AX-100 / 200 Plus
AX-100 / 200 Alpha
AX-250 / 500 Plus
AX-350 / 650 MKII
OS-1C / OS-2C
All of the Above
Automatic Door
Access Control:
OA-50C
OA-60C
OA-201C
OA-202C
OA-601C
OP-03 Series
OP-08
OS-1C / OS-2C
HA-6000T/S
All of the Above
Request For Information Form
SMA-45
All of the Above
Home and
Office Automation:
Factory
Automation:
Wireless 1000
LX-40/80N
VX-40/40A
BGS Series
C Series
J Series
JRF Series
JRF-T Series
K Series
R Series
S Series
Thermo-Hunter PT-3LF
Thermo-Hunter BUILT-IN2
X-400, 5140, VF- Series
Thermo-Hunters
V Series
V2 Series
All of The Above
How would like to receive this information?
-
Additional Comments:
Send This Form
Clear Form And Start Over
http://www.optexamerica.com/moreinfonew.cfm (2 of 2) [06/08/2000 12:24:34]
J Series Specification Sheet
Water-tight with IP-67g
protection realized by full
injection of hard epoxy
inside the body.
M8 connector types are also
available for full range of products.
JT-700
JR-200
JD-R30
JD-L03
JD-W08
●
Through-Beam Type
Retro-Reflection Type
(with Polarized Filter)
Diffused Reflection Type
Limited Range (Convergent)
Type
Wide Angle (Divergent) Type
M8 connector to minimize the space
Small M8 connector type together with a cord type enables this sensor to be installed even in a narrow
space.
http://www.optexamerica.com/products/jseries.htm (1 of 9) [06/08/2000 12:24:39]
J Series Specification Sheet
●
Screw hold design enhancing the flexibility of mounting
(The screw M3/M4 can be used)
The mounting pitch is 25.4mm and can be mounted on any mounting bracket.
●
Visible red spot that lights up detecting points (provided on each type of the convergent, diffused,
and retro-reflection types)
The visible red LED makes alignment of the detection point easy. The red spot is approximately 20mm
diam. at 30cm away from the sensor.
http://www.optexamerica.com/products/jseries.htm (2 of 9) [06/08/2000 12:24:39]
J Series Specification Sheet
●
Able to detect even a mirror-surface object or a glossy object properly
The built-in polarizing filter on Retro-reflective models enables detection of metallic surfaces.
●
Water-proof IP-67. Vibration resistance has been also remarkably enhanced.
(The inside is packed with resin)
●
Two types of control outputs, NPN and PNP (Selected by model number)
Output circuit diagram
●
Light ON/Dark ON selector switch is mounted on all models
All adjustment functions are grouped together LED indicator protrudes above the sensor so that it is
visible from all viewing angles.
●
Self-diagnosis function is mounted on all models
The self-diagnostic output warns of lens contamination before the sensor stops detecting or
http://www.optexamerica.com/products/jseries.htm (3 of 9) [06/08/2000 12:24:39]
J Series Specification Sheet
immediately upon misalignment. This prevents down-time.
●
External diagnosis TEST INPUT function (Only mounted on all models of cord type and
transmission type of connector type)
Operation test can be performed electrically interrupting the right emission.
●
Output Circuit Diagrams
http://www.optexamerica.com/products/jseries.htm (4 of 9) [06/08/2000 12:24:39]
J Series Specification Sheet
●
Type Numbers
Optical system
Side On
JT-S700N
JT-S700P
JR-S200N
JR-S200P
JD-SR30N
JD-SR30P
JD-SL03N
JD-SL03P
JD-SW8N
JD-SW8P
Head On
JT-H700N
JT-H700P
JR-H200N
JR-H200P
JD-HR30N
JD-HR30P
JD-HL03N
JD-HL03P
JD-HW08N
JD-HW08P
Side On
JT-S700CN
JT-S700CP
Head On
JT-H700CN
JT-H700CP
Through-beam
Retro-reflection
Diffused reflection
Convergent
Divergent
Optical system
Through-beam
http://www.optexamerica.com/products/jseries.htm (5 of 9) [06/08/2000 12:24:39]
J Series Specification Sheet
Retro-reflection
Diffused reflection
Convergent
Divergent
●
JR-S200CN
JR-S200CP
JD-SR30CN
JD-SR30CP
JD-SL03CN
JD-SL03CP
JD-SW8CN
JD-SW8CP
Connector Type
http://www.optexamerica.com/products/jseries.htm (6 of 9) [06/08/2000 12:24:39]
JR-H200CN
JR-H200CP
JD-HR30CN
JD-HR30CP
JD-HL03CN
JD-HL03CP
JD-HW08CN
JD-HW08CP
J Series Specification Sheet
Click Here To See The
J-Series Dimensions
Through-Beam
Retro-Reflector
Diffuse Reflection
JR-(S,H)200(C)(N,P)
JD-(S,H)30R(C)(N,P)
With Polarizing Filter
JT-(S,H)700(C)(N,P)
Detecting Distance
Detecting Object
Supply Voltage
Power Consumption
Response Time
7m
Opaque Object
10mm min.
Indicator
30cm§
Transparent and
Opaque Object
DC10~30V Including ripple (P-P) 10%
Emitter 20mA max.
30mA max.
Receiver 30mA max.
1.5ms max.
Hysteresis
Light Source
Sensitivity Adjustment
Operating Mode
2m
Opaque Object
45mm min.
0.9ms max.
-
IR LED
20% max.
Red LED
2 rotation volume / Light ON Dark ON Selectable by switch
Incident Indicator (Red) - Stable Incident Indicator (Green)
Power Indicator for Power
Control Output
NPN/PNP Open Collector 100mA max./DC30V
Alarm Output
NPN/PNP Open Collector 100mA max./DC30V
Cord Type: Available for all types - Connector: Available only in
Emitter
Test Input
Connection
Insulation Resistance
Vibration /
Shock Resistance
Ambient Temperature /
Humidity
Environmental
Illuminance
Protective Category
Material
Weight
Cord Type: Cable 2 meter - Connector Type: M8 x 4 pins
20M or more (DC500V)
Vibration: 10~55Hz width 1.5mm, XYZ 2 hours / Shock: 500m/s2
XYZ 3 times
Operating: -25~55°C / 35~85% RH
Storage: -40~70°C / 35~95% RH
Sunlight: 10,000 lux max. - Incandescent Light: 3,000 lux max.
IEC 144 - IP 67 / Case: PBT - Lens: PC (PMMA for polarizing filter
type)
Emitter 60g
65g
Receiver 65g
http://www.optexamerica.com/products/jseries.htm (7 of 9) [06/08/2000 12:24:39]
J Series Specification Sheet
§White Paper
Detecting Distance
Detecting Object
Supply Voltage
Power Consumption
Response Time
Limited Range
(convergent)
Wide Angle
(divergent)
JD-(S,H)L03(C)(N,P)
JD-(S,H)W08(C)(N,P)
2~5cm§
8cm§
Transparent and Opaque Objects
DC10~30V Including ripple (P-P) 10%
Emitter 20mA max.
30mA max.
Receiver 30mA max.
1.5ms max.
Hysteresis
Light Source
Sensitivity Adjustment
Operating Mode
Indicator
0.9ms max.
-
Red LED
IR LED
2 rotation volume / Light ON Dark ON Selectable by switch
Incident Indicator (Red) - Stable Incident Indicator (Green)
Power Indicator for Power
Control Output
NPN/PNP Open Collector 100mA max./DC30V
Alarm Output
NPN/PNP Open Collector 100mA max./DC30V
Cord Type: Available for all types - Connector: Available only
in Emitter
Test Input
Connection
Insulation Resistance
Vibration /
Shock Resistance
Ambient Temperature /
Humidity
Environmental Illuminance
Protective Category Material
Weight
Cord Type: Cable 2 meter - Connector Type: M8 x 4 pins
20M or more (DC500V)
Vibration: 10~55Hz width 1.5mm, XYZ 2 hours / Shock:
500m/s2 XYZ 3 times
Operating: -25~55°C / 35~85% RH
Storage: -40~70°C / 35~95% RH
Sunlight: 10,000 lux max. - Incandescent Light: 3,000 lux max.
IEC 144 - IP 67 / Case: PBT - Lens: PC (PMMA for polarizing
filter type)
65g
§White Paper
http://www.optexamerica.com/products/jseries.htm (8 of 9) [06/08/2000 12:24:39]
J Series Specification Sheet
http://www.optexamerica.com/products/jseries.htm (9 of 9) [06/08/2000 12:24:39]
J-Series Dimensions
http://www.optexamerica.com/products/jseriesdim.htm (1 of 2) [06/08/2000 12:24:40]
J-Series Dimensions
http://www.optexamerica.com/products/jseriesdim.htm (2 of 2) [06/08/2000 12:24:40]
K Series Specification Sheet
No Other Sensor Is As
Tough as the
Metal-Armed!!
The rigid stainless steel casing
protects the sensor from side
impacts.
KT-700
Through-Beam Type
KR-250
Retro-Reflection Type
KD-40
Diffused Reflector Type
KD-L09
Fine Spot (Convergent) Type
KR-Q50NW
Transparent Type
KR-Q150NW
●
Stainless Steel Casing Which Protects the Sensor from Side Impacts
The stainless steel casing protects the sensor from damage when it is stuck by sharp edges or corners of
passing objects.
http://www.optexamerica.com/products/kseries.htm (1 of 6) [06/08/2000 12:24:44]
K Series Specification Sheet
●
Built-In Nuts Which Cannot Be Damaged BY Over-Tightening
The built-in nuts makes installation easy and efficient, elimating the problem of thread damage caused
by over-tightening.
●
Surpasses the VDE Standard For Electrical Noise Immunity
The noise resistant circuitry is built in accordance with the strict VDE standard. Further in-house Feilen
Noise testing assures high reliability and compliance with international standards.
●
Additional Features Include:
- A multi-rubber stopper prevents the invasion of water, oil, etc.
- Small diameter cable (water-proof, oil, heat, and freeze resistant)
- Sensor-encasing noise-resistant shield
- 3 way wide angle indicator
- A polarizing filter PFK-01 (option) which prevents optical interference between through-beam
sensors.
- A slit attachment SK-01 (option) which permits the detection of extremely small objects.
Slit SK-01
(Emiter+Receiver)
Polarizing Filter
PFK-01
Slit +
Filter
Detection Distance
1000mm
3000mm
500mm
Minimum Diameter
ø1mm
ø7mm
ø1mm
http://www.optexamerica.com/products/kseries.htm (2 of 6) [06/08/2000 12:24:44]
K Series Specification Sheet
●
Can Be Mounted in Vertical or Horizontal Position
●
The Target Spot Is Clearly Visible Even at a Distance of 400mm
●
IP67 Protection Allows Use In Slightly Oily and Wash Down Areas
●
Accurate Detection Even of Transparent Materials (KR-Q50NW and KR-Q150NW)
- Non-protruding Design integrated display system with high intensity LED
- Small reflector mirror (V-42) which is a must in designing products to fit into limited spaces.
- Designed with a long, narrow field of view which enables target detection through narrow gaps.
●
Detection of Transparent Film
Stable detection even of thin film is a feature of the KR-Q50NW and KR-Q150NW (Thickness 15µm).
The high precision of the unit makes possible the detection of wrinkled film.
http://www.optexamerica.com/products/kseries.htm (3 of 6) [06/08/2000 12:24:44]
K Series Specification Sheet
●
Type Numbers
Detecting LightOn/ Sensitivity Red Test Supply Operating
Distance DarkOn Adjustment LED Input Voltage
Mode
ThroughNPN
7m
Beam
PNP
RetroNPN
2.5m
Reflective
PNP
Diffuse
NPN
400mm
DC10
Reflective
PNP
~30V
NPN
Convergent 10~90mm
PNP
Model
Number
KT-700N
KT-700P
KR-250N
KR-250P
KD-40N
KD-40P
KD-L09N
KD-L09P
Types
Transparent
Objects
500mm
1.5m
-
-
NPN
KR-Q50NW
-
NPN
PNP
KR-Q150NW
KR-Q150PW
Click Here To See The
K-Series Dimensions
Cord Type
Connector Type
Detecting Distance
Through-Beam
Retro-Reflector
Diffuse Reflection
KT-700N/KT-700P
KR-250N/KR-250P
KD-40N/KD-40P
KT-700CN/KT-700CP KR-250CN/KR-250CP KD-40CN/KD-40CP
7m
Light Source
Min. Detecting Object
2.5m
400mmÝ
Red LED
ø7mm
http://www.optexamerica.com/products/kseries.htm (4 of 6) [06/08/2000 12:24:44]
-
ø40mm
K Series Specification Sheet
Response Time
Hysteresis
1 msec. max.
0.7 msec. max.
-
-
Sensitivity Adjustment
Indicator
Control Output
Test Input
20% Max.
Not equipped
1 rotation VR
Red LED
NPN or PNP Open Collector, 100mA Max/30V DC
Equipped
Operation Mode
Connection
Insulation Resistance
Supply Voltage
Power Consumption
Not Equipped
Light On / Dark On switchable by wiring
Cable Type: 4-core 2 meter, 3.8 mm diameter / Connector Type: M8
Connector
20M ohm or more (500V DC)
10-30V DC
35mA max.
30mA max.
JIS Standard
IEC Standard
Noise
Resistance In-House
Standard
VDE Standard
Ambient
Temp /
Humidity
Ambient
Ambient
Resistance Illuminance
Vibration
Shock
Protection
Materials
Weight (Net)
C 4525
IEC 1000-4-2,3,4 Level 3
Feilen Test Level 3
Level 3
-25ºC ~ 55ºC / 35 ~ 85% RH
Sunlight 20,000 lux / Halogen light 4,000 lux
10 ~ 55Hz, vibration 1.5mm, X. Y. Z, 2 hours
Approx. 100G (1000m/s²) X. Y. Z. 3 times
IP-67
Cover (SUS304), Case (ABS), Lens (PC), PMMA for Retro type
25g (20g for emitter of through-beam type)
25g
Ý White 90% of 200 x 200mm
Convergent
Transparent objects
Cord Type
KD-L09N/KD-L09P
KR-Q50NW KR-Q150NW/KR-Q150PW
Connector Type
KD-L09CN/KD-L09CP
-
-
10 ~ 90m§
500mm
1.5m
Detecting Distance
Light Source
Min. Detecting Object
Response Time
Hysteresis
Red LED
ø7mm
0.7 msec. max.
ø40mm
10% Max.
-
-
http://www.optexamerica.com/products/kseries.htm (5 of 6) [06/08/2000 12:24:44]
K Series Specification Sheet
Sensitivity Adjustment
Indicator
Control Output
Test Input
Operation Mode
Connection
Insulation Resistance
Supply Voltage
Power Consumption
JIS Standard
IEC Standard
Noise
Resistance In-House
Standard
VDE Standard
Ambient
Temp /
Humidity
Ambient
Ambient
Resistance Illuminance
Vibration
Shock
Protection
Materials
Weight (Net)
1 rotation VR
Red LED
NPN or PNP Open Collector, 100mA Max/30V DC
Equipped
Not Equipped
Light On / Dark On switchable by wiring
Cable Type: 4-core 2 meter, 3.8 mm diameter / Connector Type: M8
Connector
20M ohm or more (500V DC)
10-30V DC
30mA max.
C 4525
IEC 1000-4-2,3,4 Level 3
Feilen Test Level 3
Level 3
-25ºC ~ 55ºC / 35 ~ 85% RH
Sunlight 20,000 lux / Halogen light 4,000 lux
10 ~ 55Hz, vibration 1.5mm, X. Y. Z, 2 hours
Approx. 100G (1000m/s²) X. Y. Z. 3 times
IP-67
Cover (SUS304), Case (ABS), Lens (PC), PMMA for Retro type
25g (20g for emitter of
25g
through-beam type)
§ White 90% of 100 x 100mm
http://www.optexamerica.com/products/kseries.htm (6 of 6) [06/08/2000 12:24:44]
K-Series Dimensions
http://www.optexamerica.com/products/kseriesdim.htm (1 of 2) [06/08/2000 12:24:45]
K-Series Dimensions
http://www.optexamerica.com/products/kseriesdim.htm (2 of 2) [06/08/2000 12:24:45]
JRF Series Specification Sheet
Easy Alignment With
Visible Beam
When the optical axis is aligned, the
orange light changes to red.
●
JRF-N
JRF-P
JRF-NC
Cord Type, NPN
Cord Type, PNP
Connector Type, NPN
JRF-PC
Connector Type, PNP
Simply Alignment
Adjust the optical axis by the color of the light source.
http://www.optexamerica.com/products/jrfseries.htm (1 of 5) [06/08/2000 12:24:49]
JRF Series Specification Sheet
●
Quick Connection of FiberOptics
Insertion indicator proves the fiberoptic is firmly assembled.
●
OFF Delay Timer
Adjustable 5-100m sec.
http://www.optexamerica.com/products/jrfseries.htm (2 of 5) [06/08/2000 12:24:49]
JRF Series Specification Sheet
●
Test Input - an external diagnosis
This function is used as the operational check of the sensor by electrically making an interruption state.
●
WaterProof IP66 [IEC standard]
●
Two types of Output; NPN or PNP
●
Light / Dark ON selectable
●
Quick DIN rail mounting
●
Operation Mode
http://www.optexamerica.com/products/jrfseries.htm (3 of 5) [06/08/2000 12:24:49]
JRF Series Specification Sheet
●
Output Circuit Diagram
●
Functions
http://www.optexamerica.com/products/jrfseries.htm (4 of 5) [06/08/2000 12:24:49]
JRF Series Specification Sheet
Click Here To See The
JRF-Series Dimensions
Type
Supply Voltage
Current Consumption
Response Time
Hysteresis
Light Source
Sensitivity Adjustment
Indicator
Control Output
Alarm Output
Test Input
Circuit Protection
Timer Function
Ambient Temperature /
Humidity
JRF-(N,P) (C)
DC 10 ~ 30V (10% of ripple inclusive)
40mA max.
350 µs max.
10%
Red LED
4 Turn Potentiomater
Incident Indicator (Red), Stable Incident Indicator (Green)
Open Collector max. 100mA/DC30V
Open Collector max. 100mA/DC30V
Available only in cord type
Reverse protection, over current protection
OFF delay 5 ~ 100 ms
Operating: -25°C ~ 55°C / 35 ~ 85% RH
Storage: -40°C ~ 70°C / 35 ~ 95% RH
Sunlight: 10,000 lux max.
Ambient Light Immunity
Incandescent Light: 3,000 lux max.
Protection Category,
IEC IP 66 Case: polysulfone Cover: PC
Material
Weight [Net]
Approx. 20g (except cord and connector)
http://www.optexamerica.com/products/jrfseries.htm (5 of 5) [06/08/2000 12:24:49]
JRF-Series Dimensions
http://www.optexamerica.com/products/jrfseriesdim.htm (1 of 2) [06/08/2000 12:24:51]
JRF-Series Dimensions
http://www.optexamerica.com/products/jrfseriesdim.htm (2 of 2) [06/08/2000 12:24:51]
JRF-T Series Specification Sheet
Self Teaching
Fiber-optic Photoelectric
Sensor
Self Adjusting Sensitivity - the
Intelligent Photosensor.
The JRF-T series is capable of accurately operating
on high-speed production lines.
●
INTELLIGENT: Moving Work Pieces
The sensitivity setting can be automatically performed by depressing the set-up button and holding it
while the work pieces pass the sensor. This method of teaching the sensor is convenient when the line
cannot be stopped or when the target is in free fall.
●
ACCURATE: 0.2mm Detection Capability Offers High Resolution
http://www.optexamerica.com/products/jrftseries.htm (1 of 7) [06/08/2000 12:24:55]
JRF-T Series Specification Sheet
Level differences as close as 0.2mm can easily be distinguished with the JRF-T series.
This high resolution also enables the sensor to distinguish between colors.
●
FAST: 300µS High-Speed Response
TThe JRF-T is the world's fastest self-teaching fiber optic sensor and can respond to signals as fast as
300µs. Previously, this fast response was only available in manually adjusted models.
4 Automatic Sensitivity Modes with One Push Button
MAX Sensitivity
Maximum sensitivity is obtained by simply sliding a switch without pushing
a button. Slide the switch to the MAX position for long distance scanning.
This mode is ideal when there is a large difference between the light and
dark signal.
* Response speed is reduced to 600 µs in this mode.
EASY Adjustment with one push of a button
This setting method requires only one push of the set-up button. This mode
is best when there is background behind the target object. The sensitivity of
the sensor is switched to the minimum difference possible and allows
detection of very fine differences.
* The alarm output should not be used in this mode.
http://www.optexamerica.com/products/jrftseries.htm (2 of 7) [06/08/2000 12:24:55]
JRF-T Series Specification Sheet
Precision Adjustment
In this mode, the set-up button is depressed twice. This is the setting which
automatically sets the detection point midway between the light and dark
target values. This method is best for position, level and mark detection.
* It does not matter if the light or dark signal is set first.
In Motion Adjustment
This mode results in the most accurate setting for moving objects. is simple
set-up allows accurate sensitivity setting without stopping the production.
Teaching Error Sign
Sensitivity ERROR Signal
This new display uses both a green and red LED
which blink alternately when an error set-up has been
made. Thgis display prevents detection errors and
false signals.
Alarm Output Function Independent of the Mode
Conventional alarm outputs employ a self-diagnosis
circuit which produces an output when the light signal
becomes weak. In addition to this signal, the JRF-T
also incorporates a function which produces an output
when a sensitivity teaching error occurs.
http://www.optexamerica.com/products/jrftseries.htm (3 of 7) [06/08/2000 12:24:55]
JRF-T Series Specification Sheet
Fiber-Optics
Click Here To See The
Fiber Optics Innovation
Click Here To See The
Fiber Optics Features
Alarm Output
Circuit
http://www.optexamerica.com/products/jrftseries.htm (4 of 7) [06/08/2000 12:24:55]
JRF-T Series Specification Sheet
http://www.optexamerica.com/products/jrftseries.htm (5 of 7) [06/08/2000 12:24:55]
JRF-T Series Specification Sheet
Model
Type
Light Source
Response time
Sensitivity Adjustment
Indicator
Control output
Alarm output
Timer function
Remote set function
Supply voltage
Power consumption
JIS standard
Noise
resistance
IEC standard
Circuit protection
Temp/humid
Illuminance
CORD TYPE
CONNECTOR TYPE
JRF-TN, JRF-TP
JRF-TCN, JRF-TCP
Red LED (60nm)
300 µs/600 µs changeable
Push Button Sensitivity Teaching Mode
Operation (Red)/Stability (Green) Indicator
NPN/PNP Open Collector Max. 100mA/DC30V
NPN/PNP Open Collector
Max 30mA/DC30V
OFF delay fixed at 40ms
Equipped
12~24V AC±10% of ripple
50mA Max.
C4525 500V
IEC801-24 LEVEL4, IEC-801-3, LEVEL3
Reverse protection, Over current protection
-25~55°C/35~85% RH
Sunlight. 10,000 lux Max, Halogen light: 3,000 lux Max.
Ambient
http://www.optexamerica.com/products/jrftseries.htm (6 of 7) [06/08/2000 12:24:55]
JRF-T Series Specification Sheet
resistance
Materials
Weight
Vibration
10~55Hz Vibration 1.5mm, X, Y, Z, 3times
Shock
Protection
Approx 50G (500m/s) X, Y, Z, 3times
IP66(IEC 144)
Case: ABS Cover: PC (Glass fiber included)
Approx 75g
Approx 35g
* Specifications is subject to change without notice
http://www.optexamerica.com/products/jrftseries.htm (7 of 7) [06/08/2000 12:24:55]
JRF-T Series Specification Sheet
Premia Golden
The high permaability of the
fiber cable greatly enhances
its pliability and its capability
to be wound. Plus, the cable
can withstand temperature
conditions from -40° to 85°C.
(Conventional models can
withstand conditions from
-40° to 70°C.)
Heat Resistance
We offer two types, a 100°
and 180°C type, for our
heat-resistance units which
can be freely cut. Moreover,
the 180°C type allows 350mm
long-distance detection.
Flexibility
A bend radius of 4mm is
possible even with M4
through-beam types and M6
reflection types. this greater
flexibility allows the sensors
to be used in such application
such as robotic arms.
Chemical-Resistance
We protect the fiber with
fluorine resin, allowing use in
chemical environments. The
fluorine resin employs PFA
with a high degree of purity.
Long Distance
Minute Spot
The diameter of the fiber core
has been increased by 1.5
times over conventional
models to increase the
detection range.
Minute spots as small as ø
0.25mm can be detected using
the sensor with the NF-DT01
model fiber. Parts as small as
0.01mm can also be detected.
Side View
For times when there is no
depth. The back corners have
been rounded, making it easy
to attach with a screw and
simple to adjust the optical
axis.
http://www.optexamerica.com/products/jrftinno.htm (1 of 2) [06/08/2000 12:24:59]
Liquid Surface
Detection
Combined with the JRF-T,
milky liquids can also ge
detected. Since the sensor has
a 120°C heat-resistant fluorine
coating, it can be used in a
wide range of liquids such as
water, oil and chemicals. Plus,
it can be used in conditions of
fog and steam.
JRF-T Series Specification Sheet
http://www.optexamerica.com/products/jrftinno.htm (2 of 2) [06/08/2000 12:24:59]
JRF-T Series Specification Sheet
Reflection Type
Form
Sensing-Distance
Unit:mm
Feature
Model
70(ø0.015)
50(ø0.015)
70(ø0.02)
M6 COAXIAL 1
NF-DB01
70(ø0.015)
50(ø0.015)
70(ø0.02)
M6 COAXIAL
WITH SLEEVE
NF-DB02
70(ø0.015)
50(ø0.015)
70(ø0.02)
M6 COAXIAL 2
NF-DB03
70(ø0.015)
50(ø0.015)
70(ø0.02)
M4/M6 COAXIAL
NF-DB04
70(ø0.015)
50(ø0.015)
70(ø0.02)
M4 LONG-DISTANCE
NF-DM01
25(ø0.015)
18(ø0.015)
25(ø0.02)
M4 STANDARD
NF-DM02
20(ø0.015)
14(ø0.015)
20(ø0.02)
M4 SLEEVE
NF-DM03
25(ø0.015)
18(ø0.015)
25(ø0.02)
M3COAXIAL
NF-DT01
5(ø0.015)
3(ø0.015)
5(ø0.02)
M3 SLEEVE
NF-DT02
Standard
Small head
Fine head
http://www.optexamerica.com/products/jrftfofeat.htm (1 of 4) [06/08/2000 12:25:04]
JRF-T Series Specification Sheet
20(ø0.015)
14(ø0.015)
20(ø0.02)
ø2.5 CYLINDRICAL
NF-DT03
70(ø0.015)
50(ø0.015)
70(ø0.02)
M6 MULTICORE
NF-DR01
9(ø0.015)
6(ø0.015)
8(ø0.02)
M3 TWO FINE CORE
NF-DR02
20(ø0.015)
14(ø0.015)
20(ø0.02)
ø3 FOUR FINE CORE
NF-DR03
9(ø0.015)
6(ø0.015)
8(ø0.02)
ø1.5 FOUR CORE
NF-DR04
5(ø0.015)
3(ø0.015)
5(ø0.02)
ø3 SLEEVE TWO
CORE
NF-DR05
Heat-proof
100(ø0.015)
70(ø0.015)
100(ø0.02)
HEAT RESISTANCE
180°C
NF-DH01
Side view
40(ø0.015)
30(ø0.015)
40(ø0.02)
STANDARD
NF-DV01
ø6 WITH
FLUORORESIN
NF-DF01
High-Frex
Liquid level
detection
Reflection Type
Form
Sensing-Distance
Unit:mm
http://www.optexamerica.com/products/jrftfofeat.htm (2 of 4) [06/08/2000 12:25:04]
Feature
Model
JRF-T Series Specification Sheet
400(ø0.5)
280(ø0.5)
400(ø0.5)
M4 LONG DISTANCE
NF-TB01
200(ø0.2)
150(ø0.2)
200(ø0.2)
M4 STANDARD
NF-TB02
200(ø0.2)
150(ø0.2)
200(ø0.2)
M4 SLEEVE
NF-TB03
70(ø0.1)
50(ø0.1)
70(ø0.2)
M4/M6
NF-TB04
200(ø0.2)
150(ø0.2)
200(ø0.2)
M3 LONG-DISTANCE
NF-TM01
M3 STANDARD
NF-TM02
ø1.5 CYLINDRICAL
NF-TM03
M4 MULTICORE
NF-TR01
M3 FOUR FINE
CORES
NF-TR02
ø1.5 FOUR FINE
CORES
NF-TR03
Heat Proof
180(ø0.2)
130(ø0.2)
180(ø0.2)
M4
HEAT-RESISTANCE
100°C
NF-TH01
Heat-proof
350(ø0.5)
240(ø0.5)
350(ø0.5)
M4 HEAT
RESISTANCE 180°C
NF-TH02
Chemical proof
1000(ø0.5)
700(ø0.5)
1000(ø0.8)
ø6 WITH
FLUORORESIN
NF-TY01
Standard
Micro head
70(ø0.1)
50(ø0.1)
70(ø0.2)
70(ø0.1)
50(ø0.1)
70(ø0.2)
180(ø0.2)
130(ø0.2)
180(ø0.2)
Flexible
55(ø0.1)
40(ø0.1)
50(ø0.2)
55(ø0.1)
40(ø0.1)
50(ø0.2)
http://www.optexamerica.com/products/jrftfofeat.htm (3 of 4) [06/08/2000 12:25:04]
JRF-T Series Specification Sheet
40(ø0.2)
30(ø0.2)
40(ø0.2)
Side View
FINE
NF-TV02
Attachment
Sensing Distance
Applicable Fiber
Unit
Model
LongDistance
MAX 8times Longer
NF-TB01, TB02,
TR01, TH01
NF-TA01
Side view
MAX 1.5times
Longer
NF-TB02, TB02,
TR01, TH01
NF-TA02
Fine spot
0.4mm at 6mm±1mm
NF-DT01
NF-DA01
Form
http://www.optexamerica.com/products/jrftfofeat.htm (4 of 4) [06/08/2000 12:25:04]
R Series Specification Sheet
Separate Type
Photoelectric Sensor
Tiny sensor heads for space
saving
R series amplifiers with its
"MARKING MODE" provide
identification even of white
substances.
Amplifier
RSA-N
RT-1500
RT-F300
Sensor Head
RD-150
RD-F50
RS-20R
RS-16G
RM-16R
RM-16G
Ideal for OEM application in need of space saving.
Also is a marking function of RS-20R and RS-16G.
●
CE conforming, world's first for this sort of Separate Types.
R series amplifiers designed in CE conforming provide tough-to-noise performance required by OEM
specifications.
●
Fastest 0.2ms response.
A fastest response among Separate Type sensors with its Marking Mode.
●
IP-66 of Sensor heads.
The sensor heads are waterproofed IP-66, being able to use a tougher environment.
●
Variety of Connector Types.
Connector types are ready for plug-in specification. PNP output applies to add models.
http://www.optexamerica.com/products/rseries.htm (1 of 8) [06/08/2000 12:25:08]
R Series Specification Sheet
●
8 types of sensor heads shaped in 3.2mm thin size.
Green LED is applicable for marking.
Sensor Head
Diffuse focused
(Red)
Diffuse mark (Red)
Diffuse focused
(Green)
Diffuse mark
(Green)
Through beam
(Long)
Through beam
(Flat)
Diffuse reflection
(Long)
Diffuse reflection
(Flat)
Amplifier
Cable type
Connector type
Type
Detecting distance
Operation mode
Light source
RS-20R
20±2mm
Normal/Mark
Red LED
RM-16R
16±2mm
Normal/Mark
Red LED
RS-16G
16±1mm
Mark
Green LED
RM-16G
16±1mm
Mark
Green LED
RT-1500
1.5mm
Normal
Red LED
RT-F300
300mm
Normal
Red LED
RD-150
150mm
Normal
Red LED
RD-F50
50mm
Normal
Red LED
Type
RSA-N
RSA-P
RSA-CN
RSA-CP
Connection
Operation mode
Normal/Mark
Cable length 2m
Normal/Mark
Normal/Mark
M8 Connector
Normal/Mark
Supply voltage
DC10~30V
DC10~30V
DC10~30V
DC10~30V
APPLICATIONS
Adhesive control RS-20R
In the mark mode, the RS-20R detect even
subtle colors. This can promptly notify
operators when adhesive has run out.
http://www.optexamerica.com/products/rseries.htm (2 of 8) [06/08/2000 12:25:08]
R Series Specification Sheet
Surface identification of chip
components/RM-16G
The RM-16G can give subtle color
discrimination that go undetected with apply
the conventional MARK SENSORS. Both red
and green LEDs are available so you would
apply the sensor to your color schemes.
Packing mark detection/RM-16R
In the mark mode, the RM-16R offers a 0.2ms
response speed, excellent for use on
high-speed lines as Packing Machines.
IC mark detection/RM-16R
The RM-16R has a 1x4mm slit spot. It stably
detects pattern changes such as prints on IC.
Wafer cassette detection/RD-F50
Just because of 3.2mm thin, the RD-F50 can
be installed practically in any tight spot, where
conventional sensors will suffer from space
problems.
CIRCUIT DIAGRAM / LOCATION OF SWITCHES /
SENSITIVITY ADJUSTMENT
NPN Output
http://www.optexamerica.com/products/rseries.htm (3 of 8) [06/08/2000 12:25:08]
R Series Specification Sheet
PNP Output
Sensitivity Adjustment
1. Set the detectable object at the detection position
and turn the sensitivity adjustor slowly from
MIN toward MAX until the Operation Indicator
lights up. Call it position A.
2. Remove the detectable object and turn the
sensitivity adjustor from MAX toward MIN
position where the Operation Indicator is
extinguished. Call it position B.
3. Point C, midway between A and B, is the
optimum Sensitivity Position
http://www.optexamerica.com/products/rseries.htm (4 of 8) [06/08/2000 12:25:08]
R Series Specification Sheet
Other Precautions
●
Other Precautions
- Wiring must be done after turning off the power.
- Verify voltage fluctuation so that it does not exceed the rated value.
- When a switching regulator is to be used with a power supply, be sure to ground the Frame Ground
Terminal.
- Do not use the R series outdoors, or in a place where extraneous light can enter the light receiving
surface directly
- Do not use the R series in a transient State at power on. (about 100 ms)
- Be careful not to install the R series at following locations, as it may otherwise malfunction. Where a
lot of dust, vapor, or the like is present. Where corrosive gas is produced. Where water, oil or the like
flies directly onto the R series.
- Do not run amplifier cables near a high-voltage lines or put them together in the same raceway. this
warning should be strictly observed to prevent malfunctions cause by inductive interference.
INSTALLATION
● Amplifier Unit
Assembling
1. Latch the front on DIN rail or bracket.
2. Push the tail down until there is a distinct
snap.
Removing
1. Pull of the lever (black) of the tail by
screwdriver, or push the amplifier unit
toward and left the front.
●
Sensor Head
1. Open a cover and pull up the Locking Lever.
http://www.optexamerica.com/products/rseries.htm (5 of 8) [06/08/2000 12:25:08]
R Series Specification Sheet
2. Process the cable end as shown.
3. Put the cables into the amplifier insertion
Holes as shown.
4. Bring down the Locking Lever.
5. Put on the cover.
Click on the Model You Would Like To See Dimensions For:
RSA-N / RSA-P
RD-150
RSA-CN / RSA-CP
RS-20R / RS-16G / RM-16R / RM-16G
RT-1500
JSN-S
RT-F300
JCN-L
RD-F50
●
Sensor Head
Diffuse focused (Red)
Type
Detecting
distance
RS-20R
20mm±2mm(Normal
mode)
16mm±2mm(Mark
mode)
Diffuse mark
(Red)
RM-16R
Diffuse focused
(Green)
RS-16G
Diffuse mark
(Green)
RM-16G
16mm±2mm
16mm±1mm
16mm±1mm
http://www.optexamerica.com/products/rseries.htm (6 of 8) [06/08/2000 12:25:08]
R Series Specification Sheet
Spot size
Standard
detecting object
Hystersis
Light source
Ambient
temp/humidity
Ambient
illuminance
Protection
category
Shock resistance
Vibration
resistance
●
ø1mm(20mm)
1x4mm(16mm)
ø1mm(16mm)
1x4mm(16mm)
20%
-
20%
Red LED
Green LED
-25°C~55°C / 35~85%RH
Sunlight: 10000lx
Halogen: 3000lx
IP-66
50G (X, Y, Z 3times each)
10~55Mz (Multiple amplitude 1.5mm X, Y, Z 2hours each)
Sensor Head
Through beam (Long)
Through beam
(Flat)
Diffuse
reflection
(Long)
RD-150
Diffuse reflection
(Flat)
Type
RT-1500
RT-F300
RD-F50
Detecting
1500mm
300mm
150mm
50mm
distance
Spot size
Standard
ø2.5mm opaque
ø5mm opaque object
detecting object
object
Hystersis
20%
30%
Light source
Red LED
Ambient
-25°C~55°C / 35~85%RH
temp/humidity
Ambient
Sunlight: 10000lx
illuminance
Halogen: 3000lx
Protection
IP-66
IP-50
IP-66
IP-50
category
Shock resistance
50G (X, Y, Z 3times each)
Vibration
10~55Mz (Multiple amplitude 1.5mm X, Y, Z 2hours each)
resistance
●
Amplifier
Type
Cable type
RSA-N/RSA-P
http://www.optexamerica.com/products/rseries.htm (7 of 8) [06/08/2000 12:25:08]
Connector type
RSA-CN/RSA-CP
R Series Specification Sheet
Supply voltage
Current consumption
Response time
Timer Function
Control output
Operation mode
Circuit protection
Ambient temp/humidity
Protection category
Connection
DC10~30V
35mA
Normal mode: 500µs Mark mode: 200µs
OFF delay fixed at 40ms
NPN or PNP Open collector output (max DC30V/100mA)
Normal mode/Mark mode
Reverse protection, over current protection
-25°C~55°C / 35~85%RH
IP-40
Cable length 2m
M8 connector
* Specifications are subject to change without prior notice for improvement.
●
Option
Model Number
JCN-S
JCN-L
BL-130S-SK
Features
Straight M8 connector cable 2m
L-shaped M8 connector cable 2m
Slits for RT-1500 (Width 0.5mm, 1.0mm, 2.0mm endlesed
together in the packing box)
http://www.optexamerica.com/products/rseries.htm (8 of 8) [06/08/2000 12:25:08]
R-Series Dimensions
Amplifier
RSA-N / RSA-P
RSA-CN / RSA-CP
http://www.optexamerica.com/products/rseries/rserdim1.htm (1 of 2) [06/08/2000 12:25:10]
R-Series Dimensions
http://www.optexamerica.com/products/rseries/rserdim1.htm (2 of 2) [06/08/2000 12:25:10]
R-Series Dimensions
Sensor Head
RT-1500 (Sender)
RT-1500 (Receiver)
http://www.optexamerica.com/products/rseries/rserdim2.htm (1 of 2) [06/08/2000 12:25:11]
R-Series Dimensions
Sensor Head Assemble Mounting
RT-1500
http://www.optexamerica.com/products/rseries/rserdim2.htm (2 of 2) [06/08/2000 12:25:11]
R-Series Dimensions
Sensor Head
RT-F300
http://www.optexamerica.com/products/rseries/rserdim3.htm [06/08/2000 12:25:13]
R-Series Dimensions
Sensor Head
RD-F50
http://www.optexamerica.com/products/rseries/rserdim4.htm [06/08/2000 12:25:14]
R-Series Dimensions
Sensor Head
RD-150
Sensor Head Assemble Mounting
RD-150
http://www.optexamerica.com/products/rseries/rserdim5.htm (1 of 2) [06/08/2000 12:25:15]
R-Series Dimensions
http://www.optexamerica.com/products/rseries/rserdim5.htm (2 of 2) [06/08/2000 12:25:15]
R-Series Dimensions
Sensor Head
RS-20R / RS-16G / RM-16R / RM-16G
Sensor Head Assemble Mounting
RS-20R / RS-16G / RM-16R / RM-16G
http://www.optexamerica.com/products/rseries/rserdim6.htm (1 of 2) [06/08/2000 12:25:17]
R-Series Dimensions
http://www.optexamerica.com/products/rseries/rserdim6.htm (2 of 2) [06/08/2000 12:25:17]
R-Series Dimensions
Connector Cable
JSN-S
JCN-L
http://www.optexamerica.com/products/rseries/rserdim7.htm [06/08/2000 12:25:18]
S Series Specification Sheet
Highest Reliability Packed
In The Smallest
Dimensions
Small but tough, its our standard!
ST-400
SR-150
SD-20
BGS-S08
Through-Beam Type
Retro-Reflection Type
Diffused Reflector Type
BGS Type
●
Flexible Adaptability of World Top Level
Four different types of extreme small size photoelectric sensors; through-beam type, diffuse-reflection
type, retro-reflection type, and BGS type are selectively available. In addition, each of these is also
available in either connector type or NPN/PNP output type so as to ensure flexible and broad adaptability
of world top level. (Especially "BGS type" gives highest performance type designed in the world's
smallest size.
●
Type Numbers
CORD TYPE 2m
Types
Through-Beam
Models
ST-400N/P
Detecting Distance
4m
Diffuse Reflection
SD-20N/P
200m
Visible Red Spot
http://www.optexamerica.com/products/sseries.htm (1 of 4) [06/08/2000 12:25:20]
Retro Reflection
SR-150N/P
1.5m
BGS
BGS-S08N/P
10~80mm
S Series Specification Sheet
Power Voltage
Output
DC10~30V
NPN / PNP
CONNECTOR TYPE
Types
Through-Beam
Models
ST-400CN/P
Detecting Distance
4m
Diffuse Reflection
SD-20CN/P
200m
Retro Reflection
SR-150CN/P
1.5m
BGS
BGS-S08CN/P
10~80mm
Visible Red Spot
Power Voltage
Output
DC10~30V
NPN / PNP
●
Compliance With Appliance Standards in Major Countries
Because of its strict compliance with CE, VDE, and UL, the S Series can be used in majpr areas of the
world.
●
Noise Reistance of High Level Conforming to CE Standard!
A smallest size, but excellent noise resistance having met the requirements of CE standard. this fact
means reliability and flexibility of the S series being applicable to various equipment and machines.
●
0.5ms High Speed Response
It's world's toplevel. A highest speed response among the amplifier built-in sensors.
●
Safe Design Conforming to VDE Standard
VDE Standard does not allow sparking from the sensor body even if the sensor encounters sudden
electrical trouble (short-circuit, over-voltage, etc.)
●
High Rigidity For 100G Shock Resistance!
Rigid design for high resistance to shock such as contact or collision against workpiece allows you to
adopt the S Series with ease.
●
Options
http://www.optexamerica.com/products/sseries.htm (2 of 4) [06/08/2000 12:25:20]
S Series Specification Sheet
Type
V-61
V-42
JCN-L
JCN-S
BL-150-10
BEF-W150B
Features
Reflection mirror for SR-150 (Standard accessory)
Small reflection mirror (Detection 1.0m)
L-Shaped M8 connector cable 2m
Straight M8 connector cable 2m
Slits for ST-400 (width 4.5mm, 1.0mm, 2.0mm-endlesed
together in the packing box)
Fitting Metal (Horizontal type)
Click Here To See The
S-Series Dimensions
Model
Through-Beam Diffuse Reflection Retro Reflection
BGS
Cable Type
ST-400N/P
SD-20CN/P
SR-150N/P
BGS-S08N/P
Connector Type ST-400CN/P
SD-20CN/P
SR-150CN/P
BGS-S08CN/P
Detecting Distance
4m
20cm
1.5m
10~80mm
Supply Voltage
DC10 ~ 30V
Current Consumption
30mA
20mA
Hysteresis
20%
10%
Minimum Detecting
45mm opaque
ø6 opaque object
Object
object
Response Time
0.5 msec.
Control Output
NPN or PNP open collector or output DC30V 100mA max.
Operation Mode
Light ON / Dark ON selectable by wiring
Sensitivity Adjustment
1 turn volume
5 turns (endless)
Indicator
Light Indicator (red)
Ambient Temperature /
-25~55°C / 35~85% RH
Humidity
Protection Category
IP-67
Ambient Illuminance
Sunlight: 10,000 lux - Halogen: 3,000 lux
(illuminance on light
receiving surface)
Shock Resistance
100G (X, Y, Z 3 times each)
Vibration Resistance
10 ~ 55Hz multiple amplitude 1.5mm (X,Y,Z 2 hours each)
http://www.optexamerica.com/products/sseries.htm (3 of 4) [06/08/2000 12:25:20]
S Series Specification Sheet
Connection
Cord Type: Cable length 2m ø3.5mm (longer cord type of 5m is available as
option) - Connector Type: M8 Connector
http://www.optexamerica.com/products/sseries.htm (4 of 4) [06/08/2000 12:25:20]
S-Series Dimensions
http://www.optexamerica.com/products/sseriesdim.htm (1 of 2) [06/08/2000 12:25:21]
S-Series Dimensions
http://www.optexamerica.com/products/sseriesdim.htm (2 of 2) [06/08/2000 12:25:21]
X-400, 5140, VF-Series Specifications Sheet
See The Temperature With Your Eyes!
X-400
Economical Model
0 ~ 400°C
5140
Sophisticated Model
-50 ~ 1400°C
http://www.optexamerica.com/products/x400.htm (1 of 5) [06/08/2000 12:25:25]
X-400, 5140, VF-Series Specifications Sheet
VF-850G,1600S,
2100S
Metal Applications
Applications
Click Here To See These
ThermoHunter's Field of View
http://www.optexamerica.com/products/x400.htm (2 of 5) [06/08/2000 12:25:25]
X-400, 5140, VF-Series Specifications Sheet
http://www.optexamerica.com/products/x400.htm (3 of 5) [06/08/2000 12:25:25]
X-400, 5140, VF-Series Specifications Sheet
Model
Measuring Field Diameter
X-400
5140L-RS
5140S-RS
ø25 / 200mm
ø32 / 1000mm
ø4 / 125mm
Measuring Range
0 ~ 400°C
Resolution
1°C or 1°F
Spectral Response
Accuracy
Emissitivity Adjustment
Response Time
Infrared Detection Element
Sighting Method
Ambient Temperature
Analog Output
Weight (Net)
-50 ~ 1400°C
-50 ~ 500°C
0.1°C: -50 ~ 150°C
1°C: 150 ~ 1400°C
7 ~ 14 µ m
±2°C(0-199°C) / ±2% of
reading (200~400°C)
0.20 ~ 1.00 (0.01 step)
0.5 sec.
1.0 sec.
Thermo-Pile
Thermo-Pile
-20 ~ 55°C
(Normal Humidity)
Sighting Notch LED Spot Marker
±0 ~ 50°C
(Normal Humidity)
-
1 mV / °C
180g (without batteries)
800g (without batteries)
Standard Accessories
-
Functions
-
Measuring Field Diameter
Measuring Range
Resolution
Spectral Response
006P (9V) Battery
Bag, Hand Strap, AC Adapter,
Analog Output / Input Cable
Digital Output Unit (RS-232C),
1000 points memory
VF-850G
VF-1600S
ø15 / 1000mm
Response Time
Infrared Detection
Element
Sighting Method
Ambient Temperature
VF-2100S
ø 4 / 1000mm
250 ~ 800°C
600 ~ 1600°C
1100 ~ 2100°C
0.9 ~ 1.9 µ m
1°C
0.7 ~ 1.1 µ m
.65 µ m
Accuracy
Emissitivity Adjustment
±1K% ± 1 digit of reading
0.10 ~ 1.00 (0.01 step)
Power Supply
Model
8 ~ 14 µ m
±5°C ± 1 digit of reading
0.10 ~ 1.00 (Continuously Variable)
0.07 ~ 0.15 sec.
0.02 ~ 0.15 sec.
Ge Diode
Silicon Photo-Diode
View Finder of Single Lens Reflex Type
±0 ~ 50°C (Normal Humidity)
http://www.optexamerica.com/products/x400.htm (4 of 5) [06/08/2000 12:25:25]
X-400, 5140, VF-Series Specifications Sheet
Analog Output
0 ~ 1000 mV
Weight (Net)
820g (without batteries)
Power Supply
006P (9V) Battery
Bag, Hand Strap, AC Adapter, Lens Cap,
Close-Up Lens Attachment, Digital Output (RS-232C)
Standard Accessories
*Specifications are subject to change without prior notice for improvement.
http://www.optexamerica.com/products/x400.htm (5 of 5) [06/08/2000 12:25:25]
X-400, 5140, VF-Series Field of View
http://www.optexamerica.com/products/x400fofview.htm (1 of 2) [06/08/2000 12:25:27]
X-400, 5140, VF-Series Field of View
http://www.optexamerica.com/products/x400fofview.htm (2 of 2) [06/08/2000 12:25:27]
Thermo-Hunter PT-3LF Specification Sheet
Quick, Non-Contact,
Surface Temperature
Measurement
Precise Measurement of 30mm at 1m Distance
You can precisely measure a narrow area where you
can not close. ( 20 / 500mm)
Coaxial Laser Marker Pinpoints the Center of the
Measuring Area
It enables you to quickly and easily focus on the
object with precision since is aims at the center of the
measuring area.
●
Applications
http://www.optexamerica.com/products/pt3lf.htm (1 of 5) [06/08/2000 12:25:30]
Thermo-Hunter PT-3LF Specification Sheet
❍
❍
❍
❍
●
Measuring Temperature Range: -20 ~ 400°C
Auto Back-light On-Off (display)
200g lightweight / portable telephone size
Quick Response: 1.5 seconds
Easy Operation
1. Point at the Target (Field of View 30 / 1000 mm)
2. Press the measure button to start measurement.
3. With release of the button, display is hold and auto off after 10 seconds
http://www.optexamerica.com/products/pt3lf.htm (2 of 5) [06/08/2000 12:25:30]
Thermo-Hunter PT-3LF Specification Sheet
Auto Back-Light On/Off in the Dark / Bright Place
(Temperature can be read even in the dark)
●
Display and Function
●
Options
HB-100
Black Tape for Non-Contact Thermometers
The Black Tape can be applied to any object, letting
you easily and correctly measure the temperature of
any object. When measuring objects with manual
emissivity settings, use the black tape and adjust the
emissivity ratio of the model to 0.95. The Black Tape
can endure temperatures up to 150°C.
PH-1
Protective Pouch for PT-3LF
http://www.optexamerica.com/products/pt3lf.htm (3 of 5) [06/08/2000 12:25:30]
Thermo-Hunter PT-3LF Specification Sheet
*The laser marker is aimed at the center of the measuring area. The laser has a 90% optical
efficiency rate. The size of the object to be measured must be sufficiently bigger than the
measuring diameter shown in the above illustration.
Model
Measuring Range
PT-3LF
-20 ~ 400°C (display -30 ~ 430°C)
Field of View
Optics
Sensing Element / Wavelength
Response Time
Measuring Accuracy
Repeatability
Display Resolution
Sighting Method
Emissivity Ratio Adjustment
Temperature Unit
Measuring Mode
Battery Life
Ambient Temperature
Ambient Humidity
Storage Temperature
Dimensions
Weight
30 / 1000 mm
Silicon Lens
Thermopile / 8 ~ 14 µ m
1.5 sec. / 90%
±1% of reading value (e=0.95) or ±2°C ± 1 digit,
whichever is greater
±1°C of reading value
1°C (1°F)
Coaxial Laser Marker (Class 2)
Dark / Bright (Switchable)
°C / °F (Switchable)
Normal / Max (Switchable)
Approx. 100 hours with backlight and LD Off and alkaline
battery
0 ~ 50°C
35 ~ 85% RH (without dew condensation)
-20°C ~ 60°C
162mm high x 52mm wide x 32mm deep
200g (including batteries)
http://www.optexamerica.com/products/pt3lf.htm (4 of 5) [06/08/2000 12:25:30]
Thermo-Hunter PT-3LF Specification Sheet
http://www.optexamerica.com/products/pt3lf.htm (5 of 5) [06/08/2000 12:25:30]
Thermo-Hunter BUILT-IN2 Specification Sheet
Measure Objects Quickly
and Accurately From a
Safe Distance - Spot
measuring within a
temperature range of 0 ~
500°C at a ±1% level of
precision
Optex's Built-In2 Thermo-Hunter is the first
non-contact thermometer of its class to incorporate a
digital display. Plus, it comes in a compact body
packed with many built-in user-friendly features to
help you measure objects with high precision. The
E-Teach function lets you easily adjust the emissivity
ratio. The Coaxial Laser Marker allows you to
confirm the measuring area.
●
E-Teach Function For Automatic Adjustment of the Emissivity Ratio
Just input the temperature of the object you wish to measure, and the built-in E-teach function
automatically calculates the emissivity ratio, which is indispensible to high-precision measuring. It
quickly adapts to any changes in the procedure or in the production line. And of course, adjusting the
the emissivity ratio by the conventional method is also possible.
http://www.optexamerica.com/products/bin2.htm (1 of 6) [06/08/2000 12:25:35]
Thermo-Hunter BUILT-IN2 Specification Sheet
●
Precise Spot Measurement in Sharp Fields of View From A Safe Distance
You can precisely measure small targets within a narrow area from a distance. You can measure an
object's temperature with accuracy just like aiming a spot-light at the object.
●
Coaxial Laser Marker Lets You Check The Target With Your Own Eyes
The built-in coaxial laser marker allows you to check the field of view. It also enables you to quickly
and easily focus on the object with precision since it aims at the center of the object, preventing the
thermometer from slipping slightly off into the wrong axis.
http://www.optexamerica.com/products/bin2.htm (2 of 6) [06/08/2000 12:25:35]
Thermo-Hunter BUILT-IN2 Specification Sheet
●
2-Type Analog Output
You can choose between two types of analog output: a TV type (1 mV / °C) which can be connected to
such devices as a panel meter or a TA-type (4-20mA) which is option for long-distance transmissions.
●
Non-Contact Measuring and the Digital Display Offer a Wide Range of Applications
●
Options
http://www.optexamerica.com/products/bin2.htm (3 of 6) [06/08/2000 12:25:35]
Thermo-Hunter BUILT-IN2 Specification Sheet
BA-AP1
Air Purge Collar (Option)
Adaptable to Dusty Environments
SC-A1
The world's first built-in Automatic Trigger
makes syncronizing signals unnecessary.
Controller made especially for the Thermo-Hunter
Built-In 2.
HB-100
Black Tape for Non-Contact Thermometers
The Black Tape can be applied to any object,
letting you easily and correctly measure the
temperature of any object. When measuring
objects with manual emissivity settings, use the
black tape and adjust the emissivity ratio of the
model to 0.95. The Black Tape can endure
temperatures up to 150°C.
*The laser marker is aimed at the center of the measuring area. The laser has a 90% optical
efficiency rate. The size of the object to be measured must be sufficiently bigger than the
measuring diameter shown in the above illustration.
http://www.optexamerica.com/products/bin2.htm (4 of 6) [06/08/2000 12:25:35]
Thermo-Hunter BUILT-IN2 Specification Sheet
Model
Measuring Range
Field of View
Optics
BA-06TV
BA-06TA
BA-30TV
BA-30TA
0 ~ 500°C (display -20 ~ 520°C)
ø 6 / 200 mm
http://www.optexamerica.com/products/bin2.htm (5 of 6) [06/08/2000 12:25:35]
ø 30 / 1000 mm
Silicon Lens
Thermo-Hunter BUILT-IN2 Specification Sheet
Sensing Element
Response Time
Measuring Accuracy
Repeatability
Display Resolution
Analog Output
Output Resolution
Sighting Method
Emissivity Ratio Adjustment
Power Source /
Consumption of Power
Ambient Temperature
Ambient Humidity
Storage Temperature
Vibration Resistance
Water Resistance
Materials
Weight
Thermopile / 8 ~ 14 µ m
500 ms / 90%
±1% of reading value or ±2°C, whichever is larger
±1°C of reading value
1°C
1mV/°C
4-20mA
1mV/°C
4-20mA
0.2°C
Coaxial Laser Marker (Class 2)
0.10 ~ 1.20 (0.01 / 1 step)
DC12 ~ 24V ± 10% - 150mA
0 ~ 50°C
35 ~ 85% RH (without dew condensation)
-10°C ~ 60°C
3G (20 ~ 50Hz, according to JIS C0911)
IP65
Ring Case: glass containing PBT, Rear Cover: PC
350g
Standard accessories: attachment fittings x 1, attachment screw (M4) x 2
Optional Accessories: Air Purge Collar
Design and specifications are subject to change for product improvement without prior notice.
http://www.optexamerica.com/products/bin2.htm (6 of 6) [06/08/2000 12:25:35]
V Series Specification Sheet
20m Sensing the longest range
through-beam sensor
Free voltage photoelectric sensor with
both vertical and horizontal lead-in
opening
2000
500
80
●
Through-Beam Type
Retro-Reflection Type
Diffused Reflector Type
VT Series
VT2000 - (AC/DC)
VT2000T - (AC/DC with timer)
VT2000D - (DC NPN output)
VT2000DP - (DC PNP output)
Major increase in detection distance to date.
Long range sensor ideal for detecting large
objects. Vast improvements in safety.
Practical Applications:
- Car position detector for parking tower
- Detecting passage of large packages and crates
http://www.optexamerica.com/products/vseries.htm (1 of 9) [06/08/2000 12:25:40]
V Series Specification Sheet
●
VR Series
VR500 - (AC/DC)
VR500T - (AC/DC with timer)
VR500D - (DC NPN output)
VT500DP - (DC PNP output)
Optics include polarizing filters. General
purpose sensor for mirror detection. Red light
beam makes for easy axis adjustment.
Practical Applications:
- Detecting the passage of metallic parts
- Sensing on production lines with installation
space on one side only
http://www.optexamerica.com/products/vseries.htm (2 of 9) [06/08/2000 12:25:40]
V Series Specification Sheet
●
VD Series
VD80 - (AC/DC)
VD80T - (AC/DC with timer)
VD80D - (DC NPN output)
VD80DP - (DC PNP output)
Big savings on installation time. Easy To
Operate. No need to bother with axis
adjustment.
Practical Applications:
- Counting items on a narrow line
- Preventing unmanned conveyor truck
collisions
●
Both vertical and horizontal lead-in opening
Fixed single-direction lead-in opening is uneconomical in terms of installment space. All models in the
"V" Series have both vertical and horizontal lead-in opening, allowing greater flexibility and
preventing problems with cord bending.
●
Detects mirror-like and shiny surfaces (VR-500 Retro-Reflection type only)
Has polarizing filter in the lens. Distinguishes
clearly between light reflected from the
reflecting mirror and other interference, so that it
can be used for sensing metal and metal plated
objects without any problem.
http://www.optexamerica.com/products/vseries.htm (3 of 9) [06/08/2000 12:25:40]
V Series Specification Sheet
●
Quick Response DC Type
Responds quickly in 1m sec., DC types.
●
Variable AC/DC power supply
AC 22 ~ 240V
DC 12 ~ 240V
●
Multi-Functional 4-Mode Timer
Set between 0.1 and 0.5 seconds in any of four different modes:
1. One-Shot Delay (O.S.D.)
Sensor outputs a signal for a fixed period from the point when sensing starts.
2. Off Delay (OFF.D.)
Sensor continues to output a signal for a set time after the point when sensing stops.
3. On Delay (ON.D.)
Sensor starts to output a signal if sensing continues for longer than a fixed period.
4. Normal (NORMAL)
Sensor outputs a signal for a fixed period from the point when sensing starts.
●
LED indicator easily visible from any direction
The light indicator can be seen easily from both the rear and the side. Internally, there is a separate
indicator for checking sensor output status.
●
Alarm Output function (Available only in DC types)
This function gives a warning when receiving light intensity that is reduced less thatn 150% of
detection level due to some dirts on the lens or wrong positioning of light axis. The photosense
indicator blinks and alarm output signal comes out.
●
Test Input function
When the #5 terminal is connected to 0V, an interrupted status is electronically invented by stoppage of
emission. This function can be used as the operational check of the sensor by electric interrupted state
without detectable object.
●
Water Resistant to IP66 (IEC 144)
●
Three different slits for reliable sensing of minute objects (Option with through-beam type)
http://www.optexamerica.com/products/vseries.htm (4 of 9) [06/08/2000 12:25:40]
V Series Specification Sheet
Slit Type
●
Photo
Attach
Min. Detection
Detection Range
V-01 (1mm type)
Both Sides
1 x 10mm
1500 mm
V-02 (2mm type)
Both Sides
2 x 10mm
3000 mm
V-05 (5mm type)
Both Sides
5 x 10mm
6000 mm
Output Circuit
http://www.optexamerica.com/products/vseries.htm (5 of 9) [06/08/2000 12:25:40]
V Series Specification Sheet
●
Components
http://www.optexamerica.com/products/vseries.htm (6 of 9) [06/08/2000 12:25:40]
V Series Specification Sheet
Click Here To See The
V-Series Dimensions
VT-2000(T)
Through-Beam
VR-500(T)
Retro-Reflector
(with polarizing filter)
VD-80(T)
Diffused
Reflection
Detecting Distance
20m
5m
80cm
Supply Voltage
Power Current
Consumption
12 ~ 240V DC ± 10% / 24 ~ 240V AC ± 10% 50/60Hz
3VA max.
2VA max.
Opaque Object
20mm min.
20ms max.
Opaque and Mirror Surface
Opaque and
Object 45mm min.
Transparent Surface
Response Time
Detecting Object
Hysteresis
Light Source
Sensitivity
Adjustment
Indicator
Timer Function
-
15% (at 80cm)
IR LED
Red LED
IR LED
1 rotation volume
With timer function: Light Indicator (Red)+Operating indicator (Red)
Without time function: Light Indicator (Red)+Power Indicator for emitter
On delay, Off delay, One-Shot delay, Selectable Timer: 0.1~5sec. (variable)
Operating Mode
LIGHT ON / DARK ON selectable
Control Output
Relay Output 1a 240V AC 3A max. 30V DC 3A max. (resistive load)
Connection
Ambient Temperature
/ Humidity
Ambient Operating
Illuminance
Noise Resisitance
Insulation Resistance
Withstand Voltage
Vibration Resistance
Shock Resistance
Protection Category
Enclosure Material
Terminal base (ø6~10mm) PF1/2(JIS B0202) Conduit outlet
-25 ~ 55ºC (but not freezing) / 35 ~ 85% RH
Sunlight: 10,000 lux max. Incandescent lamp: 3,000 lux max.
10,000Vp-p pulse width 1µs (noise simulator)
20M min. (at 500V DC)
2,000V AC for 1 minute (between power supply and outlet)
10 ~ 55 Hz amplitude 1.5mm 2 hours in each of XYZ directions
500m/s2 (approx 50G) 2 times in each XYZ directions
IP66 (IEC 144 water resistant model)
Case; lid: PPE Lens: PMMA
http://www.optexamerica.com/products/vseries.htm (7 of 9) [06/08/2000 12:25:40]
V Series Specification Sheet
Weight
Detecting Distance
Supply Voltage
Power Current
Consumption
Response Time
Detecting Object
Receiver 130g /
Emitter 110g
VT-2000D(P)
Through-Beam
VR-500D(P)
Retro-Reflector
(with polarizing filter)
VD-80D(P)
Diffused
Reflection
20m
5m
80cm
10 ~ 30V DC
55mA max.
35mA max.
1.5ms max.
Opaque Object
20mm min.
1.0 ms max.
Opaque and Mirror Surface
Opaque and
Object 45mm min.
Transparent Surface
Hysteresis
Light Source
Sensitivity
Adjustment
Indicator
Timer Function
130g
-
15% (at 80cm)
IR LED
Red LED
IR LED
1 rotation volume
Light Indicator (Red) When unstable incident, indicator comes to blink for
alarm
Power Indicator for emitter.
On delay, Off delay, One-Shot delay, Selectable Timer: 0.1~5sec. (variable)
Operating Mode
LIGHT ON / DARK ON selectable
Control Output
NPN or PNP open collector (Total 200mA max. 30V DC)
Alarm Output
When unstable incident, output transistor ON (Total 200mA max. 30V DC)
Connection
Ambient Temperature
/ Humidity
Ambient Operating
Illuminance
Noise Resisitance
Terminal Base (ø6~10mm)PF1/2 (JIS B0202) Conduit Outlet
-25 ~ 55ºC (but not freezing) / 35 ~ 85% RH
Sunlight: 10,000 lux max. Incandescent lamp: 3,000 lux max.
10,000Vp-p pulse width 1µs (noise simulator)
Insulation Resistance
Withstand Voltage
Vibration Resistance
Shock Resistance
20M min. (at 500V DC)
2,000V AC for 1 minute (between power supply and outlet)
10 ~ 55 Hz amplitude 1.5mm 2 hours in each of XYZ directions
500m/s2 (approx 50G) 2 times in each XYZ directions
Protection Category
IP66 (IEC 144 water resistant model)
Enclosure Material
Case; lid: PPE Lens: PMMA
Weight
Receiver 80g /
Emitter 75g
http://www.optexamerica.com/products/vseries.htm (8 of 9) [06/08/2000 12:25:40]
85g
V Series Specification Sheet
http://www.optexamerica.com/products/vseries.htm (9 of 9) [06/08/2000 12:25:40]
V-Series Dimensions
VT, VD, and VR All Use the Same Casing
http://www.optexamerica.com/products/vseriesdim.htm (1 of 3) [06/08/2000 12:25:43]
V-Series Dimensions
http://www.optexamerica.com/products/vseriesdim.htm (2 of 3) [06/08/2000 12:25:43]
V-Series Dimensions
http://www.optexamerica.com/products/vseriesdim.htm (3 of 3) [06/08/2000 12:25:43]
V2 Series Specification Sheet
Multivoltage Type
Photoelectric Sensors
The STRONGEST Performance
for the LONGEST Distance
OPTEX's Noise-Resistant Long-Range Sensors
Offer Stable Detection with Built-In BGS
Function.
V2T-2000
Through-Beam Type
V2R-800
BGS-V50
BGS-V39
Retro-Reflection Type
BGS Type (Cord Direct Type,
Connector Type)
OPTEX's BGS-Type Sensors Now Offer You Stable Long Range Detection in All
Environmental Conditions
●
20 Meter Long-Range Detection Even with a Red LED Indicator
1. A Wide Optical Projection Lets You Simply Adjust the Light Axis
The longer the detection distance, the more difficult it is to adjust the light axis. But, the V2 model easily
solves this problem since it features a parallel displacement approximately 1.7 times greater than that of
conventional models.
http://www.optexamerica.com/products/v2series.htm (1 of 11) [06/08/2000 12:25:50]
V2 Series Specification Sheet
2. A High Luminance Design Allows You to Check the Optical Axis.
By placing a retro-reflector in front of the receiver, the visible red light emitted by the transmitter can
easily be seen. This makes accurate alignment to ensure detection of objects over a range of up to 20
meters.
●
You Can Even Detect Black Objects at 400 Millimeters
1. Long-Range Detection Thanks to a Dual Lens
Optex employs a condenser lens which enables the maximum LED light possible at the emitter's large
diameter lens. The large lens reconverges the beam to be similar to parallel light, creating a long range
small spot. This innovation allows the detection of even black objects at a distance of 400 millimeters.
http://www.optexamerica.com/products/v2series.htm (2 of 11) [06/08/2000 12:25:50]
V2 Series Specification Sheet
2. Reliable detection with minimal background influence
When the object to be detected is black and the background is white, it is almost impossible to accurately
sense using conventional diffused sensors. The PSD element in the Optex receiver produces stable
detection with minimum hysteresis.
●
You can Detect Objects at a Distance of 8 Meters with a Red LED Indicator
1. A reflector can be installed down to 1 centimeter
A greater range of applications can be solved with the V2 series since the distance from the sensor to the
reflector can be reduced to 1/10 of that of conventional models.
2. Shiny objects can be detected at a distance of 800 mm
The Optical Axis housing contains polarized filters which allow only polarized light from the reflector to
reach the receiving element; reflected light from shiny objects cannot produce a false signal.
http://www.optexamerica.com/products/v2series.htm (3 of 11) [06/08/2000 12:25:50]
V2 Series Specification Sheet
●
Exclusive Connector makes these sensors easier to use
DC Power Connector
Optex's new pivoting connector allows vertical or horizontal cable installation by a simple
rotation. Even though the connector rotates 180°, it still maintains IP67 enclosure rating.
●
Philosophy of BGS - What is BGS?
Conventional diffuse Reflection sensors work by detecting the quantity of incoming light. Optex's BGS
senses the distance to the object in the same manner as an object in the same manner as an Auto-focus
camera. The PSD element in the sensor detects the angle of the light entering the lens and thus the distance
to the reflecting object.
http://www.optexamerica.com/products/v2series.htm (4 of 11) [06/08/2000 12:25:50]
V2 Series Specification Sheet
●
Type numbers
Light
Detecting ON/ Sensitivity Red Test Supply Operating
Types
Model Number
distance Dark adjustment LED input voltage mode
ON
AC
Through-beam
20m
o
o
o
V2T-2000
24~240V
Retro-reflection 0.01~8m o
o
o
V2R-800
±10%
Relay 1c
DC
longer 20~550mm o
o
o
BGS-V50
12~240V
BGS
shorter 10~300mm o
o
o
BGS-V30
±10%
Through-beam
20m
o
o
o
V2T-2000DN/P
DC
Retro-reflection 0.01~8m o
o
o
V2R-800DN/P
NPN/PNP
10~30V
longer 20~550mm o
o
o
BGS-V50N/P
BGS
shorter 10~300mm o
o
o
BGS-V30N/P
Through-beam
20m
o
o
o
V2T-2000CDN/P
Retro-reflection 0.01~8m
BGS
●
o
o
o
-
longer 20~550mm o
shorter 10~300mm o
o
o
o
o
-
Options
Feature
M12 Connector Cable 2m
Retro-reflector V-61
Model number
1699981
V-61
http://www.optexamerica.com/products/v2series.htm (5 of 11) [06/08/2000 12:25:50]
DC
V2R-800CDN/P
NPN/PNP
10~30V
BGS-V50CN/P
BGS-V30CN/P
V2 Series Specification Sheet
Compact retro-reflector V-42
●
Operation Mode (AC/DC)
Types
T-Beam/Retro
N.O.
Black Cable
Power OFF
Open
Output
Close
Mode Light ON
Dark ON
Open
Output
●
V-42
BGS
Light ON
N.C.
N.O.
N.C.
Gray Cable Black Cable Gray Cable
Close
Open
Close
Open
Close
Open
Close
Open
Close
Output circuit diagram
AC/DC
NPN Output
PNP Output
http://www.optexamerica.com/products/v2series.htm (6 of 11) [06/08/2000 12:25:50]
V2 Series Specification Sheet
Through Beam Type Emitter
Connector Pins
1. Brown - 2. White - 3. Blue - 4. Black
●
BGS's philosophy
http://www.optexamerica.com/products/v2series.htm (7 of 11) [06/08/2000 12:25:50]
V2 Series Specification Sheet
http://www.optexamerica.com/products/v2series.htm (8 of 11) [06/08/2000 12:25:50]
V2 Series Specification Sheet
Click Here To See The
V2-Series Dimensions
Model
Type
Cord Type
Connector Type
AC/DC Type
Through-Beam Retro-Reflection
BGS
V2T-2000
V2R-800
BGS-V50
BGS-V30
-
http://www.optexamerica.com/products/v2series.htm (9 of 11) [06/08/2000 12:25:50]
V2 Series Specification Sheet
Detecting distance
Light source
Detecting object
Response time
Hysteresis
Sensitivity adjustment
Indicator
Control output
Test input
Operating mode
Connection
Supply voltage
Power consumption
JIS Standard
Noise
resistance
IEC Standard
Withstand Voltage
Temp /
Humidity
Illuminance
Ambient
Resistance Vibration
Shock
Protection
Materials
Weight
Model
Cord Type
Type
Connector
Type
Detecting distance
Light source
Detecting object
Response time
Hysteresis
Sensitivity adjustment
20m
0.01~8m
20~550mm
10~300mm
Red LED
ø15mm
40mm
15 msec. max.
5% max.
2 rotation volume
Red LED
Relay Output 1c 250V AC 0.3A/30V DC 2A
4-core cable 2m
12~240V DC ± 10%
24~240V AC ± 10%
2VA max.
C4525 1000V
IEC1000-4-2, 4 : Level 4
IEC1000-4-3 : Level 3
1000V / sec
-25~55°C / 35 ~ 85% RH
Sunlight 1,000 lux / Halogen light 3000 lux
10~55Hz, vibration 1.5mm, X,Y, Z 2 hours
Approx. 50G (500m/S2) X,Y,Z 3 times
IP-67 (IEC 144)
Cover: ABS (Glass fiber included)
45g (15g for emitter of through-beam type)
DC Type
Through-Beam Retro-Reflection
BGS
V2T-2000DN / V2R-800DN / BGS-V50N /
BGS-V30N /
V2T-2000DP
V2R-800DP
BGS-V50P
BGS-V30P
V2T-2000CDN / V2R-800CDN / BGS-V50CN / BGS-V30CN /
V2T-2000CDP V2R-800CDP BGS-V50CP
BGS-V30CP
20m
0.01~8m
20~550mm
10~300mm
Red LED
ø15mm
40mm
1 msec max.
0.7 msec max.
2 msec. max.
5% max.
2 rotation volume
http://www.optexamerica.com/products/v2series.htm (10 of 11) [06/08/2000 12:25:50]
V2 Series Specification Sheet
Indicator
Control output
Test input
Operating mode
Connection
Supply voltage
Power consumption
JIS Standard
Noise
resistance IEC Standard
Withstand Voltage
Temp /
Humidity
Illuminance
Ambient
Resistance Vibration
Shock
Protection
Materials
Weight
Red LED
NPN or PNP open collector (Total 100mA 30V DC)
Equipped
Light ON / Dark ON selectable by wiring
Cable Type: 4-core cable 2m
Connection type: M12 x 4
10~30V ± 10% DC
35mA max.
25mA max.
C4525 1000V
IEC1000-4-2, 4 : Level 4
IEC1000-4-3 : Level 3
1000V / sec
-25~55°C / 35 ~ 85% RH
Sunlight 1,000 lux / Halogen light 3000 lux
10~55Hz, vibration 1.5mm, X,Y, Z 2 hours
Approx. 50G (500m/S2) X,Y,Z 3 times
IP-67 (IEC 144)
Cover: ABS (Glass fiber included)
45g (15g for emitter of through-beam type)
http://www.optexamerica.com/products/v2series.htm (11 of 11) [06/08/2000 12:25:50]
V2-Series Dimensions
Sensor
http://www.optexamerica.com/products/v2seriesdim.htm (1 of 3) [06/08/2000 12:25:53]
V2-Series Dimensions
Cable Connector
Reflection Mirror V-61
http://www.optexamerica.com/products/v2seriesdim.htm (2 of 3) [06/08/2000 12:25:53]
V2-Series Dimensions
Compact Type Reflection Mirror V-42 (option)
http://www.optexamerica.com/products/v2seriesdim.htm (3 of 3) [06/08/2000 12:25:53]
OA-201C Specifications Sheet
Provides a Level of Safety
Never Before Possible in
the Automatic Door
Industry
The OA-201C is a front sash mount automatic door
sensor which provides a high level of presence
sensing a wide enough detection area (2.3 m. width x
1.5 m. depth at 2.5 m. mounting height/ 7.5 ft. width
x 4.9 ft. depth at a 8.2 ft. mounting height) to assure
safe and smooth operation for even slow moving
and(or) stationary people or objects around the doors.
●
Presence Detection = Safety
The OA-201C's Presence Detection capability assures safe and reliable operation. It is capable of
sensing moving as well as slow moving or stationary people or objects. Its presence detection timer is
adjustable for 2, 15 or 60 seconds.
●
Wide and Dense Detection Area
The OA-201C's detection area consists of 18 individual detection zones (6 zones x 3 rows) which
represent 2.3 m. width x 1.5 m. depth at a 2.5 m. mounting height (7.5 ft. width x 4.9 ft. depth at a 8.2
ft. mounting height.)
●
Flexible Detection Area Setting
The width and depth of the detection area can be easily adjusted to obtain the desired detection area.
●
Environmental Disturbance Immunity
The OA-201C provides extremely dependable, low maintenance operation all year round. It operates
reliably even in harsh environments such as rain and snow because of the advanced signal processing
circuitry built into the unit.
http://www.optexamerica.com/products/oa201c.htm (1 of 3) [06/08/2000 12:25:55]
OA-201C Specifications Sheet
●
Attractive Design to Suit Any Installation Decor
●
12 - 24V AC/DC Universal Power Input
●
Form C Relay Output (Normally Open or Normally Closed Selectable)
●
Meets ANSI Standards
Click Here To See The
OA-201C's Detection Areas
Model
Detection Range
Detection Area
Detection Method
Power Input
Current Draw
Power/Operating
Indicator
OA-201CS/OA-201CBL
2.7m(8.9ft.) Max
See Chart
Near Infrared Reflection Method
12 ~ 24V AC/DC
150mA Max. (at 12V AC)
LED ON in stand-by
LED OFF when detecting
http://www.optexamerica.com/products/oa201c.htm (2 of 3) [06/08/2000 12:25:55]
OA-201C Specifications Sheet
Output Contact
Output Hold
Operating Temperature
Weight
Accessories
Form C Relay 50V 0.3A(Resistance Load)
0.5sec. Delay
-20°C ~ +55°C (-4°F ~ +131°F)
260g(9.2 oz.)
2m Wire with Plug,
2 Mounting Screws,
Mounting Template, 2 Prism Lenses
*Specifications subject to change without prior notice.
http://www.optexamerica.com/products/oa201c.htm (3 of 3) [06/08/2000 12:25:55]
OA-201C Detection Areas
DETECTION AREA CHART
A
B
C
D
E
F
Mounting Height
Area Depth
Area Depth
Area Depth
Area Width
Adjustable Range
Distance from Mounting
G
Surface
2.00 (6.56)
1.10 (3.61)
0.55 (1.80)
0.06 (0.20)
1.90 (6.23)
0.20 (0.66)
2.20 (7.21)
1.20 (3.94)
0.60 (1.97)
0.07 (0.23)
2.10 (6.89)
0.22 (0.72)
2.50 (8.20)
1.40 (4.59)
0.70 (2.30)
0.08 (0.26)
2.30 (7.55)
0.24 (0.79)
2.70 (8.86)
1.50 (4.92)
0.75 (2.46)
0.09 (0.30)
2.50 (8.20)
0.26 (0.85)
0.08 (0.26)
0.09 (0.30)
0.10 (0.33)
0.11 (0.36)
m (ft.)
http://www.optexamerica.com/products/oa201darea.htm (1 of 3) [06/08/2000 12:25:58]
OA-201C Detection Areas
ADJUSTING THE DETECTION AREA
The detection angle can be
adjusted approximately 4°. Also,
Area A and (or) Area B can be
easily eliminated by simply
turning off the switches.
http://www.optexamerica.com/products/oa201darea.htm (2 of 3) [06/08/2000 12:25:58]
OA-201C Detection Areas
The detection area can be
narrowed with the Prism Lens
provided.
The side area A and (or) B can be
eliminated with the Area
Adjusting Masking provided.
http://www.optexamerica.com/products/oa201darea.htm (3 of 3) [06/08/2000 12:25:58]
OA-202C Specifications Sheet
Activation for
Approaching Traffic and
Threshold Safety in One
Sensor is the Concept
Behind PROSAFE.
The PROSAFE OA-202C will not only activate an
automatic door from over 2m (7ft.) away, but also
provides a safe zone up to 0.8m (2.6ft.) away from
the door's threshold. By incorporating SMD (Surface
Mount Device) technology, micro-computer based
signal processing and industry leading optical
systems, OPTEX is able to provide superior
reliability and safety in ONE compact package.
●
Presence Detection
The OA-202C recognizes the presence of a motionless person from up to 0.8m (2.6ft.) away from the
door's threshold, even at floor level. The presence "Hold Open Time" is selectable from 2, 60 or 180
seconds. If any motion is detected during the hold open period, the timer will reset and begin again.
●
Deep and Wide Detection Area
The OA-202C's detection area consists of 29 individual detection zones which represent 2.3 m. width x
3.0 m. depth maximum at a 2.5 m. mounting height (7.5 ft. width x 9.8 ft. depth at a 8.2 ft. mounting
height.)
●
Flexible Detection Area Setting
The width and depth of the detection area can be easily adjusted to obtain the desired detection area.
●
Attractive Housing Design and Three Color Choices
●
12 - 24V AC/DC Universal Power Input
http://www.optexamerica.com/products/oa202c.htm (1 of 3) [06/08/2000 12:26:00]
OA-202C Specifications Sheet
●
Form C Output Relay (Normally Open or Normally Closed Selectable)
●
Meets ANSI Standards
●
Three Colors
OA-202CW (White)
OA-202CS (Silver)
OA-202CBL (Black)
Click Here To See The
OA-202C's Detection Areas
Model
Detection Range
Detection Area
Detection Method
Power Input
Current Draw
OA-202CS / OA-202CBL / OA-202CW
2.6m (6.5ft.) ~ 3.0m (9.8ft.)
See Chart
Active Infrared Reflection Method (Presence Detection
Type)
12 to 24V AC/DC Universal
Within 150mA (at 12V DC)
http://www.optexamerica.com/products/oa202c.htm (2 of 3) [06/08/2000 12:26:00]
OA-202C Specifications Sheet
Power/Operating
Indicator
Output Contact
Output Holding Time
Operating
Temperature
Weight
Accessories
When Power is Present: The Green Indicator Lamp is
Turned On
When Operating: The Green Indicator Lamp is Turned Off
Relay Contact "Form C," 50V, Within 0.3A (Resistance
Load)
Approx. 0.5 second
-20°C ~ +55°C (-4°F ~ +131°F)
320g(11.3 oz.)
Wiring Cord (2m, 1 pc.), Mounting Screw (2 pcs.),
Mounting Template (1 pc.), Area Mask Seal (1 sh.)
*Specifications subject to change without prior notice.
http://www.optexamerica.com/products/oa202c.htm (3 of 3) [06/08/2000 12:26:00]
OA-202C Detection Areas
DETECTION AREA CHART
A
B
C
D
E
F
G
H
I
J
Mounting Height
Distance to Mounting Surface
Area Depth
Area Depth
Area Width
Area Width
Area Width
Area Depth
Area Depth
Area Depth
2.20 (7.21)
0.10 (0.32)
0.07 (0.22)
0.70 (2.29)
1.30 (4.26)
1.80 (5.90)
2.60 (8.52)
2.00 (6.56)
1.40 (4.59)
1.70 (5.57)
2.50 (8.20)
0.11 (0.36)
0.08 (0.26)
0.80 (2.62)
1.50 (4.92)
2.00 (6.56)
3.00 (9.84)
2.30 (7.54)
1.60 (5.24)
2.00 (6.56)
2.70 (8.86) 3.00 (9.84)
0.12 (0.39) 0.13 (0.42)
0.09 (0.29) 0.10 (0.32)
0.90 (2.95) 1.00 (3.28)
1.70 (5.57) 1.80 (5.90)
2.10 (6.89) 2.40 (7.87)
3.20 (10.49) 3.60 (11.80)
2.40 (7.87) 2.70 (8.85)
1.70 (5.57) 1.90 (6.23)
2.10 (6.88) 2.40 (7.87)
m (ft.)
http://www.optexamerica.com/products/oa202darea.htm (1 of 3) [06/08/2000 12:26:02]
OA-202C Detection Areas
ADJUSTING THE DETECTION AREA
Area Depth Adjustment
Side View
The detection area D can be adjusted approximately 12° (3° x 4 steps). The detection areas A, B, and C are
fixed.
Areas A & B - Presence Detection
Areas C & D - Motion Detection
Area Masking
Top View
http://www.optexamerica.com/products/oa202darea.htm (2 of 3) [06/08/2000 12:26:02]
OA-202C Detection Areas
The detection areas A, B, and C can be eliminated with the Area Adjusting Masking provided.
http://www.optexamerica.com/products/oa202darea.htm (3 of 3) [06/08/2000 12:26:02]
OA-601C Specifications Sheet
PROSWING OA-601C was
developed to assure the presence
of a safety signal at the door
control in the event a person or an
object is within the swing-zone of
an automatic swinging door.
PROSWING OA-601C is ideally suited for any
brand of automatic swinging door. The area
presence pattern can be precisely adjusted for any
size (single or pair of doors) by installing one of 4
prism lens sets (included).
PROSWING OA-601C utilizes the same advanced
active infrared technology found in our
PROSAFE products.
PROSWING combines high reliability and safety
with superior presence detection technology.
●
Prism Lenses
OPTEX provides 4 unique pair of prism lenses to conform the presence pattern to a precise fit for any
size door (single or pair). Eliminates guesswork of adjusting and tweaking sensitivity to fit the area.
The presence detection pattern which is adjusted by prism lenses meets ANSI 156.10 standards.
●
Lockout Relay Operation
The PROSWING OA-601C operates in conjunction with a lockout relay and an infraredbeam to
complete the safety system (lockout relay is active during closing cycle only).
●
Presence Detection Area = Safety
PROSWING OA-601C's detection area consists of an 18-zone presence detector. Capable of sensing
moving or stationary targets, the presence detection feature assures a safety signal is present at the door
control should a person or object be within the swing-zone. The presence detection timer can be preset
to 2, 60 or 180 seconds of duration.
http://www.optexamerica.com/products/oa601c.htm (1 of 3) [06/08/2000 12:26:04]
OA-601C Specifications Sheet
●
Attractive Housing Design
Available in three color choices (black, silver, and white)
Click Here To See The
OA-601C's Detection Area
Model
OA-601CS / OA-601CBL / OA-601CW
Mounting Height
8.86 ft. (2.70 m) Max.
Detection Method
Near Infrared Reflection Method
Power Input
Current Draw
Power / Operating Indicator
Output Contact
12 ~ 24V AC/DC
120mA Max. (at 12V DC)
LED ON when standy by
LED OFF when detecting
Form C Relay 50V 0.3A (Resistance
Load)
Output Hold
Operating Temperature
0.5 sec. delay
-20°C ~ +55°C (-4°F ~ +131°F)
Weight
http://www.optexamerica.com/products/oa601c.htm (2 of 3) [06/08/2000 12:26:04]
260g (9.2 oz.)
OA-601C Specifications Sheet
Accessories
2m Wire with Plug, 2 Mounting Screws,
Mounting Template, 4 Pair Prism Lenses
*Specifications subject to change without prior notice.
http://www.optexamerica.com/products/oa601c.htm (3 of 3) [06/08/2000 12:26:04]
OA-601C Detection Areas
SINGLE DOOR
A
Mounting Height
7.2 (2190)
7.5 (2290)
Correct Prism
B
Door Width
42 inch
C
Area Depth
3.94 (1200)
4.1 (1250)
D
Area Depth
1.97 (600)
2.03 (620)
E
Area Depth
0.23 (70)
0.24 (73)
F
Area Width
3.22 (980)
36 inch
2.72 (830)
http://www.optexamerica.com/products/oa601darea.htm (1 of 3) [06/08/2000 12:26:06]
42 inch
3.35 (1020)
36 inch
2.85 (870)
OA-601C Detection Areas
G
H
Adjustable Range
Distance from Mounting
Surface
0.72 (220)
0.75 (230)
0.30 (90)
0.31 (93)
ft. (mm)
PAIR OF DOORS
A
Mounting Height
7.2 (2190)
7.5 (2290)
Correct Prism
B
Door Width
42 inch pair
C
Area Depth
3.94 (1200)
4.1 (1250)
D
Area Depth
1.97 (600)
2.03 (620)
E
Area Depth
0.23 (70)
0.24 (73)
F
Area Width
G
Adjustable Range
6.36 (1940)
36 inch pair
5.38 (1640)
0.72 (220)
http://www.optexamerica.com/products/oa601darea.htm (2 of 3) [06/08/2000 12:26:06]
42 inch pair
6.53 (1990)
36 inch pair
5.54 (1690)
0.75 (230)
OA-601C Detection Areas
H
Distance from Mounting
Surface
0.30 (90)
0.31 (93)
ft. (mm)
http://www.optexamerica.com/products/oa601darea.htm (3 of 3) [06/08/2000 12:26:06]
OP-03 Series Specifications Sheet
Passive Infrared Sensor
The Bi-Tec circuit assures performances free from
false operation. It has an illumination sensing
function, designed by Optex, to allow a high degree
of automatic sensitivity adjustment especially under
high temperature operation.
Surface and Recess Mount
OP-03AS = 12 V DC, Surface Mount
OP-03AR = 12 V DC, Recess Mount
OP-03BS = 24 V DC, Surface Mount
OP-03BR = 24 V DC, Recess Mount
Detection Area
Front and Side View
http://www.optexamerica.com/products/op03.htm (1 of 3) [06/08/2000 12:26:09]
OP-03 Series Specifications Sheet
http://www.optexamerica.com/products/op03.htm (2 of 3) [06/08/2000 12:26:09]
OP-03 Series Specifications Sheet
http://www.optexamerica.com/products/op03.htm (3 of 3) [06/08/2000 12:26:09]
OP-08C Specifications Sheet
Introducing the most
advanced, compact body,
Passive Infrared Sensor
for Request To Exit
Applications.
●
Compact and Attractive Housing Design
The OP-08C's compact and attractive housing design fits any installation. The exact size of the sensor
without the cover is only 139mm (5.47 in.) wide by 40mm (1.57 in.) high by 29mm (1.14 in.) deep
allowing for easy recessed or concealed mounting.
●
Ceiling Mounting
The OP-08C can not only be mounted on the door's transom, but also on ceiling surfaces as pictured
below.
http://www.optexamerica.com/products/op08c.htm (1 of 4) [06/08/2000 12:26:11]
OP-08C Specifications Sheet
Recessed Mount
Ceiling Mount
●
Environmental and Artificial Disturbance Immunity
The newly developed AGC circuitry, built into every unit, allows for reliable operation in areas you
never thought possible in the past. Sunlight, wind, rain and radio frequency noise can cause a
conventional passive infrared sensor to false activate, not the OP-08C.
●
Flexible Detection Area Setting
The OP-08C's detection area consists of 10 individual detection zones (5 zones x 2 rows). Each zone
can be easily eliminated by applying area masking seals. Also Standard Detection Area or Wide &
Deep Detection Area can be selected by simply rotating the spherical lens.
●
Two Color Choices (Black / White)
●
12 -24 V AC/DC Universal Power Input
●
"Form C" Output Relay (N/O or N/C)
●
Fail Safe or Fail Secure Selectable
http://www.optexamerica.com/products/op08c.htm (2 of 4) [06/08/2000 12:26:11]
OP-08C Specifications Sheet
●
"CE" Marked
Click Here To See The
OP-08C's Detection Areas
Model
OP-08CBL / OP-08CW
Mounting Height
Within 4.0m (13.1 ft.)
Detection Method
Passive Infrared Method
Power Input
Current Draw
Power / Operating Indicator
Output Contact
12 to 24V AC/DC Universal
Within 50mA (at 24V DC)
LED ON in standby
LED OFF when detecting
Form C Relay 50V 0.3A (Resistance
Load)
Output Holding Time
Operating Temperature
Approx. 1.5 sec.
-20°C ~ +55°C (-4°F ~ +131°F)
http://www.optexamerica.com/products/op08c.htm (3 of 4) [06/08/2000 12:26:11]
OP-08C Specifications Sheet
Weight
Accessories
90g (3.2 oz.)
Wiring Cord (2m, 1 pc.)
Mounting Screws (2 pcs.)
Mounting Template (1 pc.)
Area Masking Seal (1 sh.)
*Specifications subject to change without prior notice.
http://www.optexamerica.com/products/op08c.htm (4 of 4) [06/08/2000 12:26:11]
OP-08C Detection Areas
A
Mounting
Height
Standard Detection Area
C
D
B
E
F
2.5 (8.2)
0.3 (1.0)
1.8 (5.9)
3.6 (11.8)
0.8 (2.6)
2.3 (7.5)
3 (9.8)
0.4 (1.3)
2.1 (6.9)
4.3 (14.1)
1.0 (3.3)
2.8 (9.2)
4 (13.1)
0.5 (1.6)
2.9 (9.5)
5.7 (18.7)
1.3 (4.3)
3.7 (12.1)
m (ft.)
Wide and Deep Detection Area
A
G
H
I
J
K
L
M
2.5 (8.2)
Mounting
3 (9.8)
Height
4 (13.1)
0.5 (1.6)
1.5 (4.9) 2.5 (8.2) 1.4 (4.6) 3.3 (10.8) 3.0 (9.8) 5.0 (16.4)
0.6 (2.0)
1.8 (5.9) 2.9 (9.5) 1.6 (5.2) 3.9 (12.8) 3.7 (12.1) 6.0 (19.7)
0.8 (2.6)
2.5 (8.2) 3.9 (12.8) 2.2 (7.2) 5.2 (17.1) 4.9 (16.1) 8.1 (26.6)
m (ft.)
http://www.optexamerica.com/products/op08dpat.htm [06/08/2000 12:26:13]
OS-1C / OS-2C Specification Sheet
Innovative Photoelectric
Technology For Safe and
Reliable Door and Gate
Control
●
●
●
●
●
●
●
●
●
●
●
Installation flexibilty for unlimited applications
10m (33 ft.) Detection Range
Miniature sensor head and compact controller
Sensor head can be separated from shielding
wire at the plugs for easy installation
Sensor head can be installed by either
"Push-In" or "Plate Mounting"
Form C Relay Output
12-24V AC/DC Universal power input
Fail safe function
Not affected by sunlight
OS-1C can also control up to 2 sets of sensor
heads, using the sensor head unit
Fail Safe Function
http://www.optexamerica.com/products/os1c.htm (1 of 5) [06/08/2000 12:26:16]
OS-1C / OS-2C Specification Sheet
The output relay will change its state, if power is lost to the controller, to keep door opened as shown
in the following chart.
●
Power OFF
Power ON
Detect
N.O.
Close
Open
Close
N.C.
Open
Close
Open
Sensor Head Unit
The sensor head unit consists of part 1 thru 5 as shown below. If necessary during wiring, the sensor
head can be separated from the shielding wire at the plugs for easy installation.
The sensor head can be mounted by either "Push-In" or "Plate Mounting."
●
Model Number & Combinations
Model #
Type
Detection
Outer Plate
http://www.optexamerica.com/products/os1c.htm (2 of 5) [06/08/2000 12:26:16]
Options
Mounting Plate
Sensor Head Unit
OS-1C / OS-2C Specification Sheet
OS-1C
OS-2C
●
Range
Model #
Color
Point to
point type
1 beam
10m
(33 ft.)
Max.
PO-C
Chrome
Reflection
Type
4m
(13 ft.)
Max.
---
---
Point to
point type
2 beams
10m
(33 ft.)
Max.
PO-C
Chrome
Model #
PP-S
PP-B
PP-C
PR-S*
PR-B*
PR-C*
PP-S
PP-B
PP-C
Color
Silver
Bronze
Chrome
Silver
Bronze
Chrome
Silver
Bronze
Chrome
Model #
Type
SH-1
Sensor
head with
7m (23 ft.)
Shielded
wire
Applications
The OS Series is not only for automatic doors but, can be used with garage doors, gate operators, etc.
as a safety or primary control device.
http://www.optexamerica.com/products/os1c.htm (3 of 5) [06/08/2000 12:26:16]
OS-1C / OS-2C Specification Sheet
Model
Range
OS-1C (1 beam)
0 ~10m (0 ~ 33 ft.) (Point to point)
0 ~ 4m (0 ~ 13ft.) (Reflected)
Power Input
Current Draw
Output Contact
Powering/Operating
Indicator
Operating
Temperature
Weight
OS-2C (2 beams)
12 ~ 24V AC/DC
11mA
130mA
N.O. or N.C.
50F 0.1A (Resistance Load)
LED ON when stand by
LED OFF when detecting
-13°F ~ +131°F (-25°C ~ +55°C)
225g (7.94oz.)
http://www.optexamerica.com/products/os1c.htm (4 of 5) [06/08/2000 12:26:16]
350g (12.35oz.)
OS-1C / OS-2C Specification Sheet
System Components
Standard Accessories
1 Controller
1 set of Sensor head unit
with 7m (23 ft.)
Shielded wire
1 Controller
2 sets of Sensor head
unit with 7m (23 ft.)
Shielded wire
2 Fitting screws
*Specifications subject to change without prior notice.
http://www.optexamerica.com/products/os1c.htm (5 of 5) [06/08/2000 12:26:16]
HA-6000T/S Specifications Sheet
Long Range Detection for
Industrial Applications
The HA-6000T·S is an Active Infrared Presence
Sensor which provides a long-range detection area
(6m/19.7ft.)
Its unique design is perfectly suited for industrial and
commercial automatic and roll-up door applications.
●
Installation Example
http://www.optexamerica.com/products/ha6000.htm (1 of 4) [06/08/2000 12:26:19]
HA-6000T/S Specifications Sheet
●
Long Range Detection Area (6m/19.7ft)
The HA-6000T·S provides a long range detection area and is cable of sensing in applications where
high mounting locations are required.
●
Presence Detection
The HA-6000T·S has presence detection capability which is designed to provide safe and reliable
operation. It is capable of sensing both fast and slow moving objects as well as stationary objects
within its field of view. The presence detection time can be adjusted from 2 to 15 or 60 seconds.
●
Wide Detection Area Capability
A wide detection area can be obtained by using multiple units. Up to 3 HA-6000S (Slave units) can be
connected to 1 HA-600 (Master unit).
●
Flexible Detection Area Adjustment
Detection area can be adjusted 140° vertically and 120° horizontally.
●
Environmental Disturbance Immunity
The HA-6000T·S operates reliably even in harsh environments such as rain and snow because of the
advanced signal processing circuitry built into the unit.
●
Wiring Example
●
Models
HA-6000T: Master Unit
HA-6000S: Slave Unit
Click Here To See The
HA-6000T / S's Detection Area
http://www.optexamerica.com/products/ha6000.htm (2 of 4) [06/08/2000 12:26:19]
HA-6000T/S Specifications Sheet
Model
Detection Range
Detection Area
Detection Method
HA-6000T(Master unit), HA-6000S(Slave unit)
2 ~ 6m (6.6ft ~ 19.7ft)
See Chart
Near Infrared Reflection Method
http://www.optexamerica.com/products/ha6000.htm (3 of 4) [06/08/2000 12:26:19]
HA-6000T/S Specifications Sheet
Variable Range
(vertical)
Variable Range
(right & left)
Power Input
Current Draw
Power/Operating
Indicator
Output Contact
Output Hold
Operating
Temperature
Weight
Accessories
-60° ~ +80°
120°
24V DC
300mA Max. (when using 1XHA-6000T and
3XHA-6000S)
LED ON in stand-by
LED OFF when detecting
N.O. Relay Output
AC100V 1A Max. DC30V 0.1A(Resistance
Load)
0.5sec. Delay
-20°C ~ +55°C (-4°F ~ +131°F)
6000T: 470g(16.6oz)6000S: 385g(13.6oz)
Mounting Template, 3XMounting Screws(M4 X
10)
3m Wire with 4 Poles Connectors (HA-6000T
only)
0.22m Wire with 3 Poles Connectors (HA-6000T
only)
*Specifications subject to change without prior notice.
http://www.optexamerica.com/products/ha6000.htm (4 of 4) [06/08/2000 12:26:19]
HA-6000T/S Detection Areas
DETECTION AREA CHART
ADJUSTABLE RANGE
http://www.optexamerica.com/products/ha6000darea.htm (1 of 2) [06/08/2000 12:26:21]
HA-6000T/S Detection Areas
http://www.optexamerica.com/products/ha6000darea.htm (2 of 2) [06/08/2000 12:26:21]
Genesys 824R Specifications Sheet
A NEW
GENERATION
8 Zone Control
Communicator
Expandable To 24 Zones
●
●
●
●
●
●
●
●
●
●
●
8 Zones Expandable To 24
16 User Personal Identification Numbers (PINs)
5 User Authorization Levels
Real Time Clock
Remote Downloading with Security
Multiple Arming Modes
Alarm Memory
Multiple Transmission Formats
True Partitioning Capability
16 Event Retrievable Memory
Programmable Outputs
http://www.optexamerica.com/products/gen824r.htm (1 of 4) [06/08/2000 12:26:24]
Genesys 824R Specifications Sheet
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
Real Time Clock
Auto Arming with Pre-Arm Warning
1-Digit Quick Arm Function
Manual Fire, Panic and Emergency
Keypad / Keyswitch or Both
LED Status Indication for Keyswitch Use
16 User Codes w/ 5 Security Levels
Guest PIN with Auto Deletion
User Activated Bell Test
8 Zones Expandable to 16 or 24 (Fully Programmable)
Select from 5 Different Loop Types (Optional E.O.L.)
3 Different Types of Interior Zones Designed to Reduce False
Alarms Caused by User Error
All Zones Have Fire Capability
Compatible with 2 or 4 Wire Smoke Detectors
Two Entry / Exit Delay Times
Allows for True Partitioning Including Separate Keypads,
Alarm Zones, and PINs
Programmable Monitor and Walk-Test Modes
Program via Keypad or Download Software, Both with
Security to Protect Against Unauthorized Program Access
Compatible with Optex Morse Long Range Radio Equipment
Unique "Intelligent" Two-Stage Battery Charging Circuit
16 Event Alarm Memory
Bell Output
2 Auxilliary Programmable Outputs
Monitors Phone and Bell
Control Cabinet:
11 1/2" W x 11 1/2" H x 3 1/2" D
Steel w/ hinged cover. Knockout for lock. Knockouts top, bottom, side, and back.
Primary Power:
16.5 VAC 20VA transformer not included
http://www.optexamerica.com/products/gen824r.htm (2 of 4) [06/08/2000 12:26:24]
Genesys 824R Specifications Sheet
Standby Power:
12 VDC rechargeable Gel Type (not included)
Continuous Aux Power:
750mA
Lightning Protection:
MOV; spark gap
Keypad:
Maximum 4 Keypads per system, wired with Conductor Cable
Current Draw:
Panel - 100mA
Keypad 24mA (each)
Expander Module 29 mA (each)
GENESYS MODELS:
.
Description
Control / Keypad
Control Only
Keypad Only
Expander Module
Expander Module w/
Cabinet
Long Range Radio
Transmitter
G-824/KP
G-824
G-KP
G-EX
G-EXC
RF-RM1
U.L. LISTING:
.
U.L. 365
U.L. 609
U.L. 985
U.L. 1023
U.L. 1610
http://www.optexamerica.com/products/gen824r.htm (3 of 4) [06/08/2000 12:26:24]
Description
Police Connect
Local Alarm
Household Fire
Alarm
Household Burgular
Alarm
Central Station
Burgular Alarm
Genesys 824R Specifications Sheet
http://www.optexamerica.com/products/gen824r.htm (4 of 4) [06/08/2000 12:26:24]
Genesys 824 Alpha Fire Package
The Genesys 824 Alpha
Fire is considered one of
the most versatile Fire
Control Panels of its kind
on the market today.
THE GENESYS 824 ALPHA
CONTROL / COMMUNICATOR
●
●
●
●
●
●
●
●
UL listed for Commercial / Residential Fire and Burgular
Applications
Upload / Download Software
Expandable to 24 Zones
Partition Capability
Optex / Morse Quality
User Friendly
5 Year Warranty
CSFM Listed
COMMMERCIAL FIRE APPLICATIONS
http://www.optexamerica.com/products/gen824af.htm (1 of 2) [06/08/2000 12:26:25]
Genesys 824 Alpha Fire Package
Until now, Commercial Fire Applications required the purchase of an
expensive panel which made you less competitive in the bidding process. Now,
Genesys Alpha gives you flexibility to use a powerful, compact panel with a
smaller price and still provide all the features required for U.L. applications.
SPECIAL FIRE PACKAGE:
G-824-ALPHA / KP-F
includes:
1.
2.
Genesys Alpha Control Panel
Fire Rated Enclosure (RED)
3.
4.
Alpha Keypad (RED)
G-FM Fire Module (required for UL Applications)
COMFORMS TO THE
FOLLOWING U.L. LISTING:
.
U.L. 365
U.L. 609
U.L. 985
U.L. 1023
U.L. 1610
U.L. 864 / NFPA71
NFPA72 Chapter 6
Description
Police Connect
Local Alarm
Household Fire Alarm
Household Burgular Alarm
Central Station Burgular Alarm
Central Fire Station
Local Protective Signal System
Certified As a Manual & Automatic Fire Alarm System
http://www.optexamerica.com/products/gen824af.htm (2 of 2) [06/08/2000 12:26:25]
MDC Specifications Sheet
MDC Series Control
Communicator
Systems
The Optex Morse MDC Series computer based 8,
16, and 16 expandable to 48 zone digital control
communicator systems provide a new level of
functionality, programming flexibility and user
acceptance. Designed for use with the MPC-32D
Series alphanumeric Personal Control, this system
provides the subscriber with control as personal as
the individual user.
This MDC Series has the capability of
communicating with most of the digital formats
currently in use. The attractive and uniquely
designed MPC-32D Series introduces a concept in
personal controls incorporating a 32 character,
alphanumeric prompting system which simplifies
system programming for your technical department
as well as truly providing a consumer-friendly
system for ease of operation by the user.
●
●
●
●
●
Twelve volt operation
Twelve volt auxiliary output power
Smoke detector output
Local activation of remote downloading with special security PIN
Five modes of operation automatically selected by user activity:
1. On Premise Arming - perimeters armed; interior bypassed.
2. Off Premise Arming - perimeters and interiors armed with entry / exit delay.
3. Special Off Premise Arming - perimeters armed; interior bypassed; with entry / exit delay.
4. Twenty-Four Hour - system disarmed except for twenty-four hour zones.
5. Monitor - system disarmed; selected zones sound audible and display visually in Personal
Control when violated.
http://www.optexamerica.com/products/mdc.htm (1 of 8) [06/08/2000 12:26:29]
MDC Specifications Sheet
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
AC power failure indication with reporting to the Central Station
Low battery detection with reporting to the Central Station
Watchdog circuit to supervise all system functions for proper operation
Compatible with Long Range Radio system.
- requires Model RF-RM1 transmitter
- transmits all signals
- selectable modes in transmission
Up to 16 or 32 user Personal Identification Numbers (PIN). Each PIN is programmed for one of four
different priority levels:
Level 1 User - Arm, disarm, bypass and program other PINs and authorization levels
Level 2 User - Arm, disarm, and bypass
Level 3 User - Arm and disarm only
Level 4 User - Arm only
A special installer Personal Identification Number programmed by the installation company only to
allow for installation and/or service changes in the program
Opening and closing report by user
Adjustable entrance and exit delays, 0 - 255 seconds for each. Entrance delay adjustable by zone.
Adjustable pre-alarm warning delay 0 - 255 seconds
Individually adjustable bell and relay output cutoff time up to 42 minutes in ten (10) second
increments
Selectable codes for reporting by zone: Alarm, Restore, Trouble, and Bypass.
Selectable codes for reporting low battery, battery restore, AC power failure, AC restore, self-test,
duress (by user), communication failure, panic, and entering or exiting the installer program mode.
Selectable rotary or touch-tone dial transmission
Selectable 16 digit telephone numbers for each receiver
Selection of account numbers for receivers 1 and 2
Up to eight dialing attempts for each telephone number
Selectable ring back signal for opening and / or closing. Select Personal Control audible, bell or
relay output
Selectable anti-jam time to eliminate interference from other calls
Eight (8) end-of-line resistor supervised loop circuits plus emergency and duress
Two output signals: Bell, and one auxiliary relay output, selectable by zones using any combination.
Selection of pulsing or steady output for bell
Up to four (4) Personal Controls (any combination of the MPC-32 Series) per system with only four
wire connections to each Personal Control
http://www.optexamerica.com/products/mdc.htm (2 of 8) [06/08/2000 12:26:29]
MDC Specifications Sheet
●
●
●
●
Up to 16 user Personal Identification Numbers (PIN). Each PIN is programmed for one of the four
different priority levels
Adjustable self-test signal to the Central Station in one (1) hour increments up to to 255 hours with
delay for first test
One telephone line interface with full line seizure
Two telephone line interface with full line seizure with addition of the MDC-FSM Fire Supervision
Module
In addition to all of the features in the MDC-8, the Optex Morse MDC-16CET
computer based 16 zone digital control communicator system provides a new level of
functionality, programming flexibility and user acceptance. Designed for use with the
MPC-32D Series alphanumeric Personal Controls, this system provides the subscriber
with control as personal as the individual user.
This system has the capability of communicating with most digital formats currently in
use.
●
●
●
●
●
●
●
●
●
●
●
Up to 32 user Personal Identification Numbers (PIN), with individually (32) programmable duress
PINs. Each PIN is programmed for one of four different priority levels
A special PIN programmable to activate AUX Relays 1 and 2
Group Arming by User - 8 programmable groups with common group option
Partial Arming - 8 programmable groups
Individually adjustable bell, siren and relay output cutoff times up to ten (10) second increments
Daily, weekly or monthly programmable self-test signal
Listen in capability adjustable up to 255 seconds
127 Event History buffer
Programmable buffer capacity warning signals.
History print program with programmable user authorization levels
Programmable window schedules with:
- Permanent and temporary open / close schedules
- Pre-close warning signal
- Closing time extension
- Open and close exceptions report
- Holiday schedules
- Daylight Savings Time program
- Automatic Arming
- Time and Date display
http://www.optexamerica.com/products/mdc.htm (3 of 8) [06/08/2000 12:26:29]
MDC Specifications Sheet
- User Program options
For zone expansion capabilities beyond sixteen zones (up to 48 zones), you must use
model MDC-16ETX and the appropriate zone expansion modules, MDX-8M (Master)
and MDX-8S (Slave). Refer to Ordering Information below for proper equipment. This
model has all the features of the MDC-16 plus expansion capabilities.
MPC-32D PERSONAL CONTROL
The popular MPC-32D Personal Control is compatible with the MDC Series systems,
offering its high tech design to your systems. Its unique molded rubber touch pad will
complement the decor of most installations. The 32 character 2 line English language
alphanumeric display and tactile switch contacts provide the user with the simple to use,
easy to read, and understand, operating information.
Available also with a backlit display and unique dimmer control (Model MPC-32DL); the
subscriber can adjust the light intensity of the display to their own viewing comfort.
These feratures, plus the menu propted programming information for the installer, provide
all system functions and operations in an easy-to-read and easy-to-use Personal Control.
SPECIFICATIONS:
MDC-8C
Physical
Size
11.5" wide x 11.5 high x 3.5" deep
http://www.optexamerica.com/products/mdc.htm (4 of 8) [06/08/2000 12:26:29]
MDC Specifications Sheet
Weight
6 lbs.
Color
Beige
Steel cabinet with hinged cover and key lock. Knockouts
on top, bottom and rear for cable access.
Construction
Electrical
Primary Power
16.5V 20VA Class II Plug-in Transformer
Standby Power
12V DC Rechargeable Standby Battery
Current Draw
Max Tolerance
Per Loop
Continuous Auxiliary
Output Power
Peak Auxiliary
Output Power
260ma (standby)
Relay Contact
Lighting Protection
125V AC 60V DC; 5 amp, 600VA max.
MOVs, spark gap
1000 ohms
750 mA
2 amps
MDC-8CCS - Same as MDC-8C in heavy duty cabinet with special lock.
UL Listed for commercial burglary.
MDC-16CET
Physical
Size
14.5" wide x 13.5 high x 3" deep
Weight
8.75 lbs.
Color
Beige
Steel cabinet with hinged cover and key lock. Knockouts
on top, bottom and rear for cable access.
Construction
Electrical
Primary Power
16.5V 20VA Class II Plug-in Transformer
Standby Power
12V DC Rechargeable Standby Battery
Current Draw
Max Tolerance
Per Loop
Continuous Auxiliary
Output Power
260ma (standby)
Relay Contact
Siren Output
125V AC 60V DC; 5 amp, 600VA max.
Minimum impedence 8 ohms
Lighting Protection
MOVs, spark gap
1000 ohms
750 mA (Smoke Detectors, Bells, Sirens, Personal
Controls)
http://www.optexamerica.com/products/mdc.htm (5 of 8) [06/08/2000 12:26:29]
MDC Specifications Sheet
MDC-16CCS - Same as MDC-8C in heavy duty cabinet with special lock.
UL Listed for commercial burglary.
MPC-32D SERIES KEYPADS
Maximum
4 per system*
Installation
4 wire plug-in connector
MPC-32D, MPC-32DFA - 70 mA
MPC-32DL - Max intensity - 150 mA
Current Draw
Size
8.5 " wide x 5" tall x 5/8" deep
Color
Display
Natural or white
2 line, 32 character, alphanumeric
Flat bracket (provided with Personal Control). Aligns with
standard single-gang electrical box.
Mounting
*See manual for additonal required equipment.
RF-RM1
Size
7.25" wide x 8.25" high x 4.5" deep
Color
Beige
Construction
Installation
Steel cabinet with hinged cover
4 wire connections to MDC-16
*See manual for additonal required equipment.
ORDERING INFORMATION:
Model Number
MDC-8CE
MDC-8CCS
Part Number Description
Eight (8) Zone Control Communicator (including 16.5V,
20VA Transformer) with Directory, Monitor Mode
7128-0810
Options, Mini-Loader Program (Mini-Loaded ordered
separately), and Remote Downloading capability. UL
Listed Residential Fire and Burglary
Same as MDC-8C, in heavy duty cabinet with special lock.
7128-0812
UL listed for Commercial Burgular Alarm System.
http://www.optexamerica.com/products/mdc.htm (6 of 8) [06/08/2000 12:26:29]
MDC Specifications Sheet
Sixteen (16) Zone Control Communicator (including
16.5V, 20VA Transformer) with Directory, Monitor Mode
Options, Mini-Loader Program (Mini-Loaded ordered
separately), Group Arming by User, Partial Arming,
Built-In Remote Downloading capability (requires
MDC-RDM or MDC-RDL ordered separately) and real
Time Clock with Window Schedules, Test Time Programs,
Auto Arm and History Buffers. UL Listed Residential Fire
and Burglary and Commercial Fire.
Same as MDC-16CET in UL Housing. UL Listed
Commercial Burglary.
MDC-16CET
7128-1605
MDC-16CCS
7128-1602
MDC-16ETX
7128-1609
MDX-8M
7128-0081
MDX-8S
7128-0082
MDC-24ETX
7128-1610
Same as MDC-16ETX with 24 zones
MDC-32ETX
7128-1611
MDC-XPR-24
7128-1612
MDC-XPR-32
7128-1613
MPC-32D
7128-0032
Same as MDC-16ETX with 32 zones
Twenty-four zone expander in separate cabinet; with two
additional Form C Relays; must be used with
MDC-16ETX
Thirty-two zone expander in separate cabinet; with two
additional Form C Relays; must be used with
MDC-16ETX
Personal Control with thirty-two (32) character
alphanumeric LCD display with bracket
MPC-32D EXP
7128-0048
Same as MPC-32D with expanded address
MPC-32DL
7128-0040
Same as MPC-32D with Backlit Display
MPC-32DL EXP
7128-0032
MPC-32DFA
7128-0031
Same as MPC-32DL with expanded address
Same as MPC-32D with audible and visual annunciation
for UL Commercial Fire systems
MPC-32DLFA
7128-0054
Same as MPC-32DFA with Backlit Display
MPC-32DW
7128-0052
Same as MPC-32D, White
MPC-32D/LW
7128-0053
Same as MPC-32DL, White
MPC Mini Loader
7128-0036
MDC-FSM
7405-0001
MDC-DISC
MDC-RDM
7131-0016
7128-0037
Storage File for quick programming
Fire Supervisory Module for UL Commercial Fire
Systems. Supervises bell and telephone lines
Remote Downloader Software
Ring Detect Module for Remote Downloading
Same as MDC-16CET, expandable to 48 zones
Eight zone master expander module; provides two
additional Form C Relays; one required for expansion
Eight zone slave expander module; one required for each
eight zones (up to 48) after the MDX-8M is installed
http://www.optexamerica.com/products/mdc.htm (7 of 8) [06/08/2000 12:26:29]
MDC Specifications Sheet
MDC-RDL
5000-0326
RB-1215
RF-RM1
MDC Demo Kit
Literature
Literature
9444-0200
7130-1003
7128-0034
3491-0033
3491-0048
Plug-in module for remote downloading with answering or
fax machines on line
12.5V, 1.8 Ah Rechargeable Battery
Radio Transmitter
Salesman's Briefcase Demonstrator
8 Page End User Brochure
4-Color Brochure with MPC-32D Keypad
http://www.optexamerica.com/products/mdc.htm (8 of 8) [06/08/2000 12:26:29]
Super MDC Specifications Sheet
Super MDC
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
Two regular schedules for each partition (8
partitions total)
Program reporting of open/close for each
schedule (Monitors time of open and time
of close and reports if the open time is early
or delayed)
Faster Download Speed (Run Time
Compression Technology)
Programmable option to monitor one or
both phone lines
Real Time Clock (Tied to either crystal
clock) AC / 50Hz or 60Hz or only DC
Programmable Name separate for each
partition
Globalize zone programming up to 9 zone
types
On board two fully supervised phone lines. Supervision for line cut, ringing, and off hook condition
One supervised fire bell output with provision for external 12 or 24V AVA compliant power supply
connection
3 Programmable outputs (open collectors): 2-Bell, 2-Relays, and 3 PGMs
Separate Key switch input
Separate connection for G-EX expander board, for expanding zone up to 80
Smart battery charging circuit which monitor load current, change current, and voltage. Digitally
controlled.
Brownout protection by Battery Disconnect Circuit
No fuses (fuseless)
Remote Bench Testing
Supervisory fire zone to make alarm audible on keypad
99 User Pin codes
Monitor mode: Silent, Audible, Chime, Pin Activate, and Single Key activated monitor mode
http://www.optexamerica.com/products/supermdc.htm (1 of 4) [06/08/2000 12:26:31]
Super MDC Specifications Sheet
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●
Auto Walk Test: Automatically tests each zone throughout the course of the day and lets you know
if a zone did not report.
512 event memory buffer
Open Close supervisory zones
U.L. Listing
Time of Day Activity Control
Alpha Description by Location
Up to 8 Keypads
As many as 8 True Partitions
Real Time Clock
Unauthorized access detection (Monitors up to 5 attempts then reports to Central Station)
User function to extend Open/Close time by 1 hour
Scroll Scan Speed selectable while in installer program menu
Fire Walk Test (Installer activated only) Recycles latching switch.
User activated Fire Walk Test
New advanced utility for installer to debug the system providing voltage and current measurements
of battery, aux. Power, fire bell output and ground fault.
New option of 50Hz / 60Hz AC source for real time clock or option of using crystal clock.
Single key SCAN option (no pin number needed)
New flexible receiver reporting routing: 9 different choices
Separate account numbers for groups with flexible receiver reporting routing Programmable
Features
16 Zone expandable to 80 (fully programmable)
Remote zone capability by using G-EX
Programmable zone type and loop type including Garage Door type zone (ignored for Away arm)
Temporal code for fire bell: Modulating bell in series of 3 second intervals
SPECIFICATIONS:
Physical
Size
14.5" wide x 13.5 high x 3" deep
Weight
8.25 lbs.
Color
Beige
Steel cabinet with hinged cover, key lock and knockouts on
bottom and rear.
Construction
http://www.optexamerica.com/products/supermdc.htm (2 of 4) [06/08/2000 12:26:31]
Super MDC Specifications Sheet
Electrical
Primary Power
16.5V 40VA Class II Transformer
Standby Power
Current Draw
Max Tolerance
Per Loop
12V DC Rechargeable Standby Battery
260ma (standby)
Cont. Aux. Power
Relay Contact
Lighting Protection
1.65 Amps
125V AC 60V DC
MOVs
50ma Outputs
5 amp 600VA Max
1000 ohms
PGM Outputs
ORDERING INFORMATION:
Model Number
Part Number
SMPC-32D
70400
Description
Personal Control with thirty-two (32) character
alphanumeric LCD display with bracket
SMPC-32D Exp. 70402
Same as SMPC-32D with Expander Address
SMPC-32DL
Same as SMPC-32DL with Bracket Display
70401
SMPC-32DL Exp. 70404
Same as SMPC-32DL with Expander Address
Same as SMPC-32DFA Same as SPC-32D with
Audio and Visual for UL Commercial Fire
system
SMPC-32DFA
70404
SMPC-32DFLA
70405
Same as SMPC-32DFA with Backlit Display
SMPC-32DW
70408
Same as SMPC-32D White
SMPC-32DLW
70409
Same as SMPC-32DL White
SMPC-DISC
70320
Remote Downloading Software
RB-1215
9444-0200
12.5V 1.8AH Rechargeable Battery
RF-RM1
7130-1003
Radio Transmitter
MDC Demo Kit
70301
Sales Demonstration Briefcase
G-EX
7128-4001
8 Zone Hardwire Expander
G-EXC
7128-4003
8 Zone Hardwire Expander with Cabinet
http://www.optexamerica.com/products/supermdc.htm (3 of 4) [06/08/2000 12:26:31]
Super MDC Specifications Sheet
http://www.optexamerica.com/products/supermdc.htm (4 of 4) [06/08/2000 12:26:31]
AX-350/650MKII Specification Sheet
EXTENDED DETECTION
RANGE, MORE RELIABLE
PERFORMANCE
Advanced Photoelectric Technology now
comes with extended range performance,
while superior design allows for easy and
cost effective installation and maintenance.
The AX-MKII Series is specially designed for
unsurpassed stability even in the most hazardous
outdoor environments. Our patented I.A.S.C. circuit
assures fast and easy alignment of the photoelectric
beams, keeping installation time to a minimum. Just
take a look at our industry leading list of advanced
features.
●
Patented Integreated Alignment Status Communication
Photobeam alignment is no longer a costly, time-consuming job. The beam alignment level is visually
displayed using LED indicators located on both the transmitter and receiver. By simply aiming both
units and watching the LED indicators, accurate and reliable alignment is easily achieved. The
alignment status at the receiver is optically transferred to the transmitter and is indicated by LEDs. To
align the transmitter, one simply monitors the LED level while adjusting.
http://www.optexamerica.com/products/ax350.htm (1 of 5) [06/08/2000 12:26:35]
AX-350/650MKII Specification Sheet
●
4-channel Selectable Beam Frequencies
"Cross talk" is eliminated by our field selectable beam frequency.
1) 2 Beam Stacking
2) 2 Beam Long Distance Stacking
●
Reliability Chart for Outdoor Protection
Specially designed to eliminate various causes of outdoor false alarms.
False Alarm Causes
Lightning & High EMI
Disturbances
Insect Entering into
Housing
Technology to Solve
High EMI Resistance
Sealed Enclosure Housing
http://www.optexamerica.com/products/ax350.htm (2 of 5) [06/08/2000 12:26:35]
AX Function & Features
High Surge Resistiveness Relay &
EMI Surge Absorber
IP54
AX-350/650MKII Specification Sheet
Ultra High Power Transmitter
Anti-Frost Mechanism
High Sensitivity Tolerance
Patented I.A.S.C.
Dew Condensation
Excellent Optical Alignment Easy Optical Alignment Mechanism
Fog, Frost & Heavy Rain
Environmental Analysis
Environmental Disqualification
Circuit
Automatic Gain Control
Birds or Flying Objects
Size Analysis
Twin Synchronized Pulsed Beams
Cross Talk of Beams
Beam Discrimination
Selectable Beam Frequencies
●
Environmental Disqualification Circuit
The Environmental Disqualification Circuit eliminates false alarms generated by gradual signal loss
caused by extreme weather conditions such as snow, fog, heavy rain, icy build-up.
●
Re-Transmission Capability
The Re-Transmission Circuit can be used as an alternative to a conventional protective wiring loop, or
where a long run of wire is difficult or impossible. It may also be used to eliminate the cost of long
distance wiring to remote areas. Simple connection of an N/C device to the beam transmission
terminal.
●
Lightning & Surge Protection
An improved EMI surge absorber and high surge resistiveness relay will maintain stable operation even
in the most lightning prone areas.
●
A.G.C. (Automatic Gain Control) Circuit
The A.G.C. Circuit continually monitors for gradual changes in the signal's strength caused by
changing weather conditions. It adjusts the sensitivity accordingly to maintain the proper signal level
for the current environmental conditions.
●
Adjustable Beam Interruption Period
Beam interruption time can be adjusted according tot he peculiarities of each installation site. When
protecting a wall or fence, a long interruption time will catch intruders, but let jumping cats pass
through. Adjustable from 50 to 500msec.
●
Other
http://www.optexamerica.com/products/ax350.htm (3 of 5) [06/08/2000 12:26:35]
AX-350/650MKII Specification Sheet
- Twin Synchronized Pulsed Beams Designed for Greater Stability
- 99% Beam Blocking Rate
- Anti-Frost Design
- Stainless STeel Screws & Back Plate
- Knock-Outs for 1/2 Inch Conduit
- Form C Relay Providing More Flexibility
●
Options
HU-1: Heating Unit
For use in cold areas. 24V DC/AC, 430mA max.
BC-1: Back Cover
AX-BT: Beam Tower
For stacking beams at a height of 5.78 ft. (1.75m)
http://www.optexamerica.com/products/ax350.htm (4 of 5) [06/08/2000 12:26:35]
AX-350/650MKII Specification Sheet
Model
Detection Method
Range (Outdoor)
Maximum Arrival
Distance
Beam Characteristics
Selectable Beam
Frequency
Interruption Period
Power Input
Current Draw
(transmitter+receiver)
Alarm Period
Alarm Output
Tamper Switch
Operating
Temperature
Environment Humidity
Alignment Angle
Alarm Memory
Environmental
Disqualification
Circuit
Mounting
Weight
AX-350MKII
AX-650MKII
Infrared Photoelectric
350 ft. (100m)
650ft. (200m)
3,500ft. (1,000m)
6,500ft. (2,000m)
Pulsed infrared
4 channel (Automatic synchronization)
50 ~ 500m/sec (Selectable)
10.5 ~ 30VDC
Normal operation 75mA max
During optical alignment 145mA max
2 sec (±1) nominal
Form C Relay (28VDC 0.2A Max.)
N.C. opens when cover is removed
-30 ~ 131°F (-35 ~ +55°C)
95% Max.
± 10° Vertical, ± 90° Horizontal
LED indicates memory status.
Selectable Negative & Positive
Form C relay operates when beam energy has
been gradually reduced to abnormal level
Wall or Pole
98.8 oz(2800g) (Both Transmitter and Receiver)
*Specifications and design are subject to change without prior notice.
NOTE: This unit is designed to detect an intruder and activate an alarm
control panel.
Being only a part of complete system, we cannot assume responsiblity for
theft or damages, should it occur.
http://www.optexamerica.com/products/ax350.htm (5 of 5) [06/08/2000 12:26:35]
BX-100 BoundaryGard Specifications Sheet
Alarm BEFORE burgular breaks
in!
Optex presents a new concept, BoundaryGard,
which offers more reliable protection and security
options. Especially, this is designed to protect the
perimeter of the building that we designate as the B
zone.
B zone areas like windows and roll-up doors have
been secured only by magnetic contacts or glass
break detectors so far. Now, BoundaryGard
protects a building's exterior by detecting intruders
before entry is attempted and can also provide a
deterrent with a sounder before the break-in occurs.
●
●
●
●
●
FULL TIME (NO/NC) RELAYS
Separate Form A and Form B relays can be used for Security and other functions. Local alarm,
annunciation and automation can work simultaneously.
ATTRACTIVE, SLENDER DESIGN
A smaller design and optional white, paintable cover will allow the unit to harmonize with any type of
architecture.
EASY ALIGNMENT WITH VISUAL AND AUDIBLE INDICATOR
No vertical adjustment is necessary in this detector.
A sounder activates and LED comes on when the sensor is miss-aligned and shuts off when aligned.
This will assist you in the alignment process. Also, the Audible Alignment/Alarm Indicator can be used
as a deterrent to intruders. This option can be turned on or off with a switch inside the detector.
LIGHT REDUCTION FILTER
Increases the units resistance to external light sources making it more reliable and also less likely to be
defeated by alternative light sources.
MAX 99 PERCENT BEAM BLOCKAGE
http://www.optexamerica.com/products/bx100.htm (1 of 4) [06/08/2000 12:26:38]
BX-100 BoundaryGard Specifications Sheet
It will increase the units resistance to false alarms caused by environmental disturbance such as fog in
the condition the beam alignment status achieves the highest level.
●
Applications
●
Options
- Spacer: SP-1
(For use when height adjustment of the unit is required.)
- Metal Guard - MG-1
(Helps protect the unit from tampering or vandalism.)
http://www.optexamerica.com/products/bx100.htm (2 of 4) [06/08/2000 12:26:38]
BX-100 BoundaryGard Specifications Sheet
- White Decorative Cover - WC-1
Allows the unit to harmonize with various types of architecture. Hood is included which can be fixed to
this cover for rain and frost proof.
BX-100PLUS
Outdoor: 100ft. (30m)
Indoor: 200ft. (60m)
Range
Max Arrival Ditance
Detection Method
Beam Characteristics
1,000ft. (300m)
Simultaneous interruption of two
infrared beams
Pulsed Infrared
Interruption Period
50 msec
Power Input
10.5 - 28V DC
Current Draw
55mA (StandBy) / 75mA (Max)
Alarm Period
2 ± 1 sec (Delay)
Relay Output
2 relay outputs N.O. and N.C.
28VDC 0.2A (Max) each
http://www.optexamerica.com/products/bx100.htm (3 of 4) [06/08/2000 12:26:38]
BX-100 BoundaryGard Specifications Sheet
Beeping Period
15 ± 1 sec (Delay)
Volume of Audible Alarm Indicator Approx. 70 dB (at 1 meter distance)
Tamper
N.C. opens when cover is removed
Operating Temperature
-30°F ~ +131°F (-35°C ~ +55°C)
Environmental Humidity
95% (max)
Alignment Angle
Mounting
Weight
IP Rating
Accessories
http://www.optexamerica.com/products/bx100.htm (4 of 4) [06/08/2000 12:26:38]
±92° Horizontal
Wall (indoor / outdoor)
14.1 oz (400g)
IP 54
Self Tapping Screws x 4
Wiring Sponges x 2
AX-100S/AX-100SR Specification Sheet
Versatility That Meets
Every Demand
INTERIOR PHOTOELECTRIC SYSTEM
● Distance to 100 feet
● Surface (AX-100S) or Flush (AX-100SR)
models
● Both models mount with a standard single gang
electric box
● LED alignment indicator - visibly confirms
proper alignment
● Multi-Focus Optics eliminates the need for
vertical alignment
●
●
Easy Vertical Alignment
An improved EMI surge absorber and high surge resistiveness relay will maintain stable operation even
in the most lightning prone areas.
❍
No Vertical Aligment Necessary
With multi-focus optics creating an oval shape beam, if the transmitter and receiver are
installed at the same height, vertical adjustments are not necessary.
http://www.optexamerica.com/products/ax100s.htm (1 of 4) [06/08/2000 12:26:41]
AX-100S/AX-100SR Specification Sheet
❍
Visible Optical Aligment
LED indicator of the transmitter visibly confirms the beam alignment. Supplied check-shield
confirms proper alignment.
http://www.optexamerica.com/products/ax100s.htm (2 of 4) [06/08/2000 12:26:41]
AX-100S/AX-100SR Specification Sheet
●
Crystal Oscillated Dual Modulated Pulsed Beam
Receiver discriminates a coded signal from the transmitter, giving high level prottection against
sunlight, flourescent and incandescent lamps.
●
Installation
❍
❍
Pre-Wired Installation
Both units mount easily with a standard single gang electrical box (U.S. standard). The
AX-100SR recesses inside, and the AX-100S mounts directly over to cover a single gang
box.
Options
FR-100: mounting hardware for AX-100SR if electrical box is not used.
Model
AX-100S
http://www.optexamerica.com/products/ax100s.htm (3 of 4) [06/08/2000 12:26:41]
AX-100SR
AX-100S/AX-100SR Specification Sheet
Detection Method
Range
Maximum Arrival
Distance
Beam
Characteristics
Interruption Period
Power Input
Current Draw
Alarm Period
Alarm Output
Tamper Switch
Operating
Temperature
Environment Humidity
Alignment Angle
Mounting
Weight
Infrared Photoelectric
Indoor 100ft. (30m) or Less
400ft. (120m)
1000 pps. 9500A
Double Modulation pulsed infrared
50 msec.
8 ~ 18 VDC.
Transmitter 27mA max/ 8 ~ 18 VDC
Receiver-Red LED On in alarm condition
2 sec. (+-1) nominal
N.C.28VDC., 0.2Amax
Opens when cover is removed.
-4°F to 122°F (-20 °C to 50°C)
95% max
±90° Horizontal
Wall and SW.
Box (Surface)
8.5 oz. (240 g)
±15 ° Horizontal
Wall and SW.
Box (Flush)
5.6 oz. (160 g)
*Specifications are subject to change without notice for improvement.
http://www.optexamerica.com/products/ax100s.htm (4 of 4) [06/08/2000 12:26:41]
FX-360 Specifications Sheet
Cost Effective Perfection
The FX-360 Ceiling Mount Detector with its
unique, highly durable sperical lens offers
unparalleled 360° Detection Performance and
Reliability.
The FX-360 is an extremely cost effective 360 ceiling
mount detector. It provides the most unbeatable
detection performance and reliability in its class. The
FX-360's sleek and compact design suits all types of
installation applications.
●
Originally Designed Hard Sperical Lens
The FX-360's hard sperical lens is designed with precision - an original feature that enables this
detector to provide reliable detection throughout its 360° area.
●
False Alarm Protection
The FX-360 prevents false alarms caused by environmental changes or insensitivity to high
temperatures.
❍
❍
❍
❍
RFI Protection
No alarm to 20V/m from 100MHz. to 1 GHz.
Temperature Protection
No alarm during temperature changes from -4° to +122°F at 3° per minute
(-20° to 50°C at 1.7°C per minute)
Noise Reduction Circuit
Selectable Pulse Count: 2,4
http://www.optexamerica.com/products/fx360.htm (1 of 4) [06/08/2000 12:26:45]
FX-360 Specifications Sheet
●
Advanced Quality Control
❍
❍
●
Other Features
❍
❍
●
Computerized S.M.D. Technology
Using robotics to mount miniturized chip components ensures a smooth and
uniform production level of high quality.
Running Test On Every Circuit Board
All circuit boards sustain a "Burn-In" test for many hours.
LED On/Off Switch
Warm-up Indicator
Versions
❍
❍
❍
❍
FX-360: Standard
FX-360L: Alarm Memory
FX-360S: Form C Relay
FX-360V: Alarm Memory and Patented Double Conductive Shielding of Pyro Element
Click Here To See The
FX-360's Detection Patterns
http://www.optexamerica.com/products/fx360.htm (2 of 4) [06/08/2000 12:26:45]
FX-360 Specifications Sheet
Model
Detection Method
Coverage
FX-360
Passive Infrared
ø25ft. ~ ø40ft.(ø8m ~ ø12m)
Height: 8ft. ~ 12ft.(2.4m ~ 3.6m)
Detection Zones
Sensitivity
Detectable Speed
62 zones
3° F (1.6° C) at 2 ft. / sec. (0.6 m / sec.)
1 ~ 5 ft. / sec. (0.3 ~ 1.5 m / sec.)
LED Indicator
LED blinks during warm-up period
Alarm indicator optional
Alarm Period
2.0 ± 0.5 sec.
Alarm Output
N.C.28V DC., 0.2A max.
Tamper Switch
N.C., Opens when cover is removed.
Pulse Count
Warm-Up Period
20 ± 5 sec. 2 or 4
Approx. 30 sec. (LED Blinks)
http://www.optexamerica.com/products/fx360.htm (3 of 4) [06/08/2000 12:26:45]
FX-360 Specifications Sheet
Current Draw
Weight
Operating
Temperature
Environment
Humidity
RF Interference
17mA/(normal) 18mA/(max.)
4.90 oz. (140g)
-4°F ~ +122°F (-20°C ~ +50°C)
95% max.
No Alarm 20 V/m
*Specifications are subject to change without notice for improvement.
L Version (Alarm Memory)
Model
Alarm Memory
Current Draw
Weight
FX-360L
FX-360L(P)
System Armed:
0 ~ 1V DC
(grounded)
System Armed:
+5 ~ 20V DC
17mA/(normal) 35mA/(max.)
4.90 oz. (140g)
S Version (Form C)
Model
FX-360S
Alarm Memory
Form C 28V DC 0.2A max.
Current Draw
32mA/(normal) 35mA/(max.)
Weight
4.90 oz. (140g)
V Version
Model
FX-360V
Power Input
6 ~ 18V DC
Alarm Memory
System Armed: 0 ~ 1V DC (grounded)
Current Draw
Weight
13mA/(normal) 25mA/(max.)
4.90 oz. (140g)
http://www.optexamerica.com/products/fx360.htm (4 of 4) [06/08/2000 12:26:45]
FX-360 Detection Patterns
http://www.optexamerica.com/products/fx360detpatt.htm [06/08/2000 12:26:46]
RX-40PI Information
To See The Product Specifications Sheet,
Click Here
http://www.optexamerica.com/products/rx40main.htm [06/08/2000 12:26:47]
To See A Slide Show Presentation of the
Detector, Click Here
RX-40PI Specifications Sheet
Quad Zone Logic
Optex improves its patented "Multifocus Optics"
technology to create "Quad Zone Logic" for accurate
detection of humans. Using this logic, the RX-40PI
has been designed to give extremely high false alarm
protection with tolerance to spot temperature changes
from curtains or small to medium size animals.
Optex's Optical Quad Technology user taller
detection zones divided into upper and lower areas. It
detects IR energy changes in both areas and then
couples them for extremely accurate detections.
Offering very high reliability in hostile areas.
●
Quad Zone Logic - Recognizes humans and ignores most small animals
Quad Zone Logic provides multi segmented detection zones over the detection area. An alarm signal is
created by the cumulated total IR energy of each zone. It is designed so that a human size target will
normally fill 4 to 8 zones, and this will cause an alarm to be generated. Any smaller temperature
change (i.e. small to medium size pets, rodents or moving curtains) only activates one or two zones at
the same time creating a much weaker detection signal. Pet immunity applies to animals 0 to 16 inches
in height. These signals are further analyzed by the "ECO" chip and signal processing circuit for
accurate detection of humans and avoidance of most small animals.
http://www.optexamerica.com/products/rx40.htm (1 of 5) [06/08/2000 12:26:50]
RX-40PI Specifications Sheet
●
Spherical Lens - Technology to Back Up Quad Zone Logic
Obtains an accurate focal length for each detection zone and maximizes the performance of Quad Zone
Logic.
●
Trouble Free and Easy Installation
http://www.optexamerica.com/products/rx40.htm (2 of 5) [06/08/2000 12:26:50]
RX-40PI Specifications Sheet
❍
❍
Trouble-Free and Easy Knockouts - Simply push with a screwdriver to open a hole of
matching size with the cables.
❍
Durable Spherical Lens and Housing Design
Good Wiring Space and Guide
Selectable Pulse Count: 2 or 4
LED On/Off Switch
❍
❍
❍
●
Performance
❍
❍
●
Sealed Housing - prevents drafts and insects from reaching the pyro element
RFI Protection
No alarm at 20 V/m from 100MHz to 1 GHz
Temperature Compensation Logic
Eco chip includes temperature compensation circuit. It controls sensitivity to improve
stability against changes in environmental conditions.
Optional Multi-Angle Bracket
http://www.optexamerica.com/products/rx40.htm (3 of 5) [06/08/2000 12:26:50]
RX-40PI Specifications Sheet
❍
❍
FA-3
Wall and Ceiling Mounting Bracket
Horizontally ±45°, Vertically 0° to 15° downwards
FL-60N
Long Range (Extremely Dense Multi Layer Curtain Lens)
(Pet Immunity is not available with FL-60N)
Click Here To See The
RX-40PI's Detection Patterns
Model
Detection Method
Coverage
RX-40PI
Passive Infrared
Wide: 40 ft. x 40 ft. (12m x 12m), 85°Wide
Detection Zones
Wide: 78 zones
Mounting Height
5 ~ 8 ft. (1.5 ~ 2.4m)
Sensitivity
Detection Speed
3.6°F (2°C) at 2 ft/sec. (0.6m/sec.)
1 ~ 5 ft/sec. (0.3 ~ 1.5m/sec.)
LED Alarm Indicator
Switchable On/Off
Alarm Period
Approx. 2.5 sec.
Alarm Output
N.C., 28VDC, 0.2A max.
http://www.optexamerica.com/products/rx40.htm (4 of 5) [06/08/2000 12:26:50]
RX-40PI Specifications Sheet
Pulse Count
Approx.20 sec. 2 or 4
Warm Up Period
Approx. 30 sec.
Power Input
Current Draw
9.5 ~ 16V DC
17mA (max.) at 12V DC
Weight
2.5 oz. (70 g)
Operating Temperature
Environmental Humidity
RFI Interference
-4°F ~ +122°F (-20°C ~ +50°C)
95% max.
No alarm 20V/m
*Specifications are subject to change without prior notice.
FL-60N (Optional Lens for Long Range Curtain Pattern)
Coverage
Long: 60 ft. x 60 ft. (18m x 18m) Long Range
Detection Zones
Long: 20 Zones
http://www.optexamerica.com/products/rx40.htm (5 of 5) [06/08/2000 12:26:50]
RX-40PI Detection Patterns
http://www.optexamerica.com/products/rx40dpat.htm [06/08/2000 12:26:52]
RX-40PI Slide Show
All Passive Infared detectors (PIRs) can detect humans but, few have the ability
to discriminate between humans and other, smaller, sources of infrared energy.
In recent years, Optex engineers have focused their efforts on creating a PIR
capable of ignoring small to medium animals (pets, rodents, and other false
alarm sources) while still maintaining reliable detection of human-sized targets.
http://www.optexamerica.com/products/rx40_show/slide1.htm [06/08/2000 12:26:53]
RX-40PI Slide Show
Pet Immunity
78 Detection Zones
Perfect Focus
For Greater Sensitivity
Installer Friendly
Design
Optex Quality
The RX-40PI is the achievement from this effort. Seventy-eight detection zones
(nearly twice that of conventional PIRs) help the RX-40PI to detect human
sized intruders while ignoring other sources of infrared, such as pets, heating
vents, and drapes. The RX-40PI's sperical lens creates "perfect focus" and
optimum sensitivity, enabling it to achieve such unprecedented capabilities.
http://www.optexamerica.com/products/rx40_show/slide2.htm [06/08/2000 12:26:55]
RX-40PI Slide Show
Perfect Focus with the Sperical Lens
Poor Focus with the Flat Lens
The RX-40PI's "better vision" is a key contributor to its Pet Immunity function.
The sperical lens of the RX-40PI creates a uniform focal length for each
detection zone and achieves clear, sharp, zone definition. Conventional lenses
are flat and then bent to fit the detector's cover. This creates differing focal
lengths within each lens segment and makes the detector's vision blurred, giving
it imprecise detection zone borders.
http://www.optexamerica.com/products/rx40_show/slide3.htm [06/08/2000 12:26:57]
RX-40PI Slide Show
Target Area
RX-40PI's Spherical Fresnel Lens
(Perfect Focus)
Flat Lens
(Poor Focus)
The 3-D graphs show the actual responses of detectors to the same target signal.
Notice how much more sharply the RX-40PI responds than its competitor. The
RX-40PI's peak is actually 50% higher that its competitor. Superior sensitivity
is a significant contributor to Pet Immunity. The stronger signal created by the
RX-40PI (shown on left) creates a larger range in which we can distinguish
between humans and smaller sources of infrared energy. In other words, greater
sensitivity creates greater contrast between humans and smaller targets.
http://www.optexamerica.com/products/rx40_show/slide4.htm [06/08/2000 12:26:58]
RX-40PI Slide Show
Temperature Detection
This picture illustrates temperatures which are typical for a man and a dog.
Notice that most targets consist of a variety of temperatures. Depending on the
background temperature, either the head, the torso, or the legs might offer
optimum contrast.
http://www.optexamerica.com/products/rx40_show/slide5.htm [06/08/2000 12:27:00]
RX-40PI Slide Show
Traditional Zones
Traditional detection zones are too small to see the entire target. They often
miss areas of the target which offer the greatest temperature contrast. Even if
time is spent carefully aiming the detector, full coverage cannot be achieved.
http://www.optexamerica.com/products/rx40_show/slide6.htm [06/08/2000 12:27:01]
RX-40PI Slide Show
RX-40PI Detection Zones
The RX-40PI has a much better way! Its vertically aligned detection zones are
coupled together to respond to human sized targets,while ignoring smaller
targets. Basically speaking, when four or more zone segments are affected, the
RX-40PI will activate. For small to medium sized pets, however, only one or
two zones will be affected and no alarm will occur. This is how the RX-40PI
achieves high sensitivity to human sized targets, while easily ignoring pets.
http://www.optexamerica.com/products/rx40_show/slide7.htm [06/08/2000 12:27:02]
RX-40PI Slide Show
Quad Zone Logic
We call this "Quad Zone Logic". Quad Zone Logic refers to the layout of the
zones into tall vertical barriers:
Close To The Detector:
Zones cover the entire target, four or more zones are required for an alarm;
High sensitivity to humans, ignores small pets and many other causes of false
alarms
Middle Range:
Lower zones are still pet immune. Upper zones are slightly more sensitive to
humans to ensure good catch. Pet immunity is still achieved.
Furthest Distance:
Lower area has no detection zones. Upper area is slightly more sensitive to
ensure good catch. Pet immunity is still achieved.
http://www.optexamerica.com/products/rx40_show/slide8.htm [06/08/2000 12:27:04]
RX-40PI Slide Show
This chart show the same detection area as before. Now, it is highlighted to
show where pet immunity is greatest. Lower areas of the room, which are more
likely to contain a pet, are very resistant to small animals. Upper areas are more
sensitive to provide high sensitivity to human sized targets. This method allows
for reliable pet immunity, while still remaining sensitive to human targets.
http://www.optexamerica.com/products/rx40_show/slide9.htm [06/08/2000 12:27:05]
RX-40PI Slide Show
What size pet can the RX-40PI ignore?
Optex knows that providing accurate information about our technology helps
security professionals achieve the best pet immunity performance. Since no
motion detector (PIR or Dual technology) can determine an object's weight, pet
size is the most accurate measure of pet immunity. In nearly every application,
the RX-40PI will ignore any animal 16 inches in height or less.
http://www.optexamerica.com/products/rx40_show/slide10.htm [06/08/2000 12:27:07]
RX-40PI Slide Show
Simple Installation
For best pet immunity performance, the following installation guidelines
must be followed:
Mount the detector between 7 and 8
feet (closer to 8 ft. for more
immunity)
Limit the detectors field of view to
30 ft. maximum
Do not angle the detector downward
(flat on wall or corner mount only)
Don't allow pet accessible shelves or
stairways 5.5 ft. or higher within 15
ft. of the detector
No additional adjustments are necessary! Simple and quick installation.
http://www.optexamerica.com/products/rx40_show/slide11.htm [06/08/2000 12:27:08]
RX-40PI Slide Show
Easy Installation Features
Knockouts
Bracket and Lens
Wiring Guides
RX-40PI also features: Easy wire knockouts to simplify installation and
provide better sealing of the casing. Wiring Guides on the back of the detector
to allow for easy passage of wires to the terminals. Optional long range lens
and optional wall / ceiling bracket for greater flexibility and easier installation.
(Do not use long range lens or wall / ceiling bracket for pet immunity
applications).
http://www.optexamerica.com/products/rx40_show/slide12.htm [06/08/2000 12:27:10]
RX-40PI Slide Show
False Alarm Hazards
Radio Waves
Headlights and Other Bright Light Sources
Spiders and Other Insects
RX-40PI's RFI immunity exceeds industry standards. With RFI immunity
exceeding 20 V/m. Superior white light filtering has been incorporated into the
RX-40PI's design to reduce interference from car headlights, sunlight, or other
bright light sources. The unit's optical chamber is sealed to create an
impenetrable insect shield around the pyroelectric element. The RX-40PI is
rated for operating temperatures as low as -4°F.
http://www.optexamerica.com/products/rx40_show/slide13.htm [06/08/2000 12:27:11]
RX-40PI Slide Show
RX-40PI Benefits
Its patented Quad Zone Logic fills rooms with 78 detection zones which are
capable of distinguishing between humans and small animals, heating vents,
and other causes of false alarms. Easy to install and reliable, the RX-40PI's pet
immunity is an important sales advantage for you to offer your customer and a
significant false alarm reduction tool for all applications.
http://www.optexamerica.com/products/rx40_show/slide14.htm [06/08/2000 12:27:13]
CX-50 / 50AM Specification Sheet
Introducing the new CX Models
with the Most Advanced
Technology and Reliability to Fit
the Needs of the Commercial
Market!
DUAL PURPOSE SPHERICAL LENS:
Wide Angle: 50 x 50ft. (15 x 15 m) at medium
sensitivity
Long Range (Curtain): 80 ft x 6 ft. (24 x 1.8m) at
medium sensitivity
With the introduction of the CX-50, the scope of the
CX series is greatly increased. The CX-50 not only
includes all the outstanding features of the CX Series,
but incorporates such high value added features as
Anti-Masking and Self-Checking in the CX-50AM
verison.
●
Double Conductive Shielding of Pyro Electric Element (Patent Pending)
Double filtering and conductive metal shielding of the Pyro blocks out visible light and RFI allowing
only infrared energy to reach the pyroelectric elements.
http://www.optexamerica.com/products/cx50.htm (1 of 6) [06/08/2000 12:27:16]
CX-50 / 50AM Specification Sheet
CX-50 (Standard) /50S (Form C) / 50V (Alarm Memory)
●
False Alarm Protection
❍ RFI Protection
No alarm from a field strength of 30V/m within the range of 100 to 1,200 MHz.
❍ EMI Protection
Can endure 50,000V of electrical interference from lightning or power surges through the
signal or power lines.
❍ Visible Light Protection
Stable against halogen light at 8ft. (2.4m) or 50,000lx of reflected sun light within the detection
area.
Exceptionally high level of protection against morning sun reflection or car headlights.
❍ Temperature Protection
No alarm in high, low and changing temperatures from -4°F to +122°F (-20°C to +50°C)
●
Stable Detection Performance
❍ Temperature Compensation
The CX-50 Series employs Temperature Compensation to provide accurate detection by
automatically adjusting its sensitivity according to the environmental temperature. It will
prevent non detection under high temperature conditions where the background temperature is
very similar to the human body, while maintaining a high level of false alarm protection.
❍ Selectable Sensitivity (H,M,L)
Offers sensitivity selection to give detection coverage of up to 60 x 60ft. (18 x 18m) Wide
Angle or 90 x 7ft. (27 x 2.1m) Long Range.
❍ Selectable Pulse Count (1, 2, 3 or 4)
(2 pulse count on long range detection)
❍ Multifocused Optics (Patent Listed)
Maintains stable detection even in adverse temperature conditions because tall, vertical zones
are created through the multifocused optics. They capture an entire human body and detect the
smallest temperature contrast against the background.
http://www.optexamerica.com/products/cx50.htm (2 of 6) [06/08/2000 12:27:16]
CX-50 / 50AM Specification Sheet
●
Spherical Lens Technology
Spherical Lens Technology offers both flexibility and reliability, enabling all installation site
requirements to be met by a single detector.
❍ Spherical Lens Design
Conventional interchangeable lenses inevitable meet sensitivity distortion problems when flat
long range detection lenses are bent to fit a curbed housing cover. Optex's spherically designed
lens will obtain sharp detection for both Wide Angle and Long Range using the same lens
surface.
- Long Range Pattern focused though a spherical lens
Designed to collect IR energy from the detection area, and purely focus it onto the pyro.
- Long Range Pattern focused through a bent, flat lens (conventional models)
Because a flat lens is "bent", sensitivity distortion occurs at both sides of the lens, (the lens
surface is not directing IR energy correctly), resulting in poor sensitivity for long distance
detection applications.
http://www.optexamerica.com/products/cx50.htm (3 of 6) [06/08/2000 12:27:16]
CX-50 / 50AM Specification Sheet
❍
❍
❍
●
Selectable Sensitivity (H,M,L)
Offers sensitivity selection to give detection coverage of up to 60 x 60ft. (18 x 18m) Wide
Angle or 90 x 7ft. (27 x 2.1m) Long Range.
Hard & Durable Fresnel Lens
Dual Purpose Lens
By simply rotating the spherical lens, Wide Angle or Long Range patterns can be selected.
CX-50AM ANTI-MASKING & SELF-CHECKING
Improved Reliability
❍ Anti-Masking (Patent Pending)
By providing two photoelectric detection beams, operating in different directions, the
CX-50AM unlike other Anti-masking PIRs will detect masking both directly to the lens surface
and also shielding in front of the PIR. Either of these actions will generate a trouble signal.
❍
❍
Self-Checking
This function activates a trouble signal if CX-50AM's sensing ability is not circuits. Correctly,
The Sensor and Signal Processing Circuit are automatically checked once every 5 hours and
also when the alarm system is armed (a compatible control panel is necessary to send an
arming signal to the CX-50AM's alarm memory input). This ensures system integrity.
Initial Alarm Memory (CX-50AM Only)
This function is indicated by a red LED and memorizes which detector was first triggered
http://www.optexamerica.com/products/cx50.htm (4 of 6) [06/08/2000 12:27:16]
CX-50 / 50AM Specification Sheet
when several detectors are connected in one alarm loop.
Click Here To See The
CX-50 / 50AM's Detection Patterns
Model
CX-40R(NC)
Detection Method
Coverage
CX-40R
(NO)
CS-60NR
(NO)
Passive Infrared
40ft x 40ft
60 ft x 3ft
(12m x 12m) (18m x 1m)
85° Wide Full Curtain
92 zones
Detection Zones
CS-60NR
(NC)
20 zones
40ft x 40ft
60 ft x 3ft
(12m x
(18m x 1m)
12m)
Full Curtain
85° Wide
92 zones
20 zones
Multi Level Full Curtain
Multi
Full Curtain
Area
Area
Level Area
Area
Mounting
Height 5 ~ 12ft (1.5 ~ 3.6m)
Sensitivity
3° F (1.6°C) at 2ft/sec. (0.6m/sec.)
http://www.optexamerica.com/products/cx50.htm (5 of 6) [06/08/2000 12:27:16]
CX-50 / 50AM Specification Sheet
Detectable Speed
1 ~ 6ft/sec. (0.3 ~ 1.8m/sec.)
LED Indicator
Disabled during normal operation
Alarm period
1 ± 0.5 sec.
Alarm Output
N.C. 28VDC 0.2A max
N.O. 28VDC 0.2A max
Tamper Switch
N.C., Opens when cover
removed.
N.O., Closes when cover
removed
Pulse Count
Warm Up Period
Power Input
20 ± 5 sec. Second delay
App. 40 sec.
9VDC Alkaline Battery, Lithium Battery
Current Draw
Battery Life
Weight
Operating
Temperature
Environment
Humidity
20µA
App. 2 years/Alkaline Battery; 4 years/Lithium
Battery
4.8 oz
4.6 oz
4.8 oz
4.6 oz (130g)
(135g)
(130g)
(135g)
-14° F ~ + 122° F (-10° C + 50° C)
95% max
*Specifications and design are subject to changewithout prior notice.
Ordering References
Model No.
Detection Pattern
Relay Output
40' x 40' (12 x 12 m)
N.C.
60' x 3' (18 x 1m)
N.C.
CX-40R NO
40' x 40' (12 x 12 m)
N.O.
CX-40R NO
60' x 3' (18 x 1m)
N.O.
CX-40R NC
CX-60NR NC
http://www.optexamerica.com/products/cx50.htm (6 of 6) [06/08/2000 12:27:16]
CX-50/50AM Detection Patterns
http://www.optexamerica.com/products/cx50dpat.htm (1 of 2) [06/08/2000 12:27:18]
CX-50/50AM Detection Patterns
http://www.optexamerica.com/products/cx50dpat.htm (2 of 2) [06/08/2000 12:27:18]
CX-70M Specifications Sheet
Dual Purpose Lens
Wide Angle: Up to 70 x 70 ft. (21 x
21m)
Long Range: Up to 150 x 8 ft. (45 x
2.4m)
Proven Performance With Detection Pattern
Flexibility For Commercial Applications
Superior reliability and performance makes the
CX-70M a logical choice for a wide variety of
commercial applications. In addition to providing all
of the superior features of our CX-line of P.I.R.s, the
CX-70M allows you to select between precise wide
angle detection patterns and long range patterns. By
incorporating our Patented Multifocus Technology
into a Spherically Designed Lens, the CX-70M has
successfully eliminated sensitivity problems caused
by changing detection patterns.
●
Double Conductive Shielding of Pyro Electric Element (Patent Listed)
Double filtering and conductive metal shielding of Pyro blocks out visible light and RFI allowing only
infrared energy to reach the pyroelectric elements.
http://www.optexamerica.com/products/cx70m.htm (1 of 4) [06/08/2000 12:27:20]
CX-70M Specifications Sheet
●
Dual Purpose Lens
By simply rotating the spherical lens, you can select between Wide Angle and Long Range patterns.
CX-70M will instantly provide reliable and precisely accurate detection in each pattern.
●
Flexibility For Installation Size
Combining unique Dual Purpose Lens with sensitivity and angle adjustments, CX-70M will create
ideal zone patterns for human detection in every size room.
●
False Alarm Protection
❍
❍
❍
❍
RFI
No alarm at 30V/m from 100MHz to 1.2GHz.
EMI
No alarm against 50,000V charge
White Light
No alarm against Halogen light within 8 ft. (2.4m)
Sunlight
No alarm at 50,000 lx reflected into the detector
●
Multi Focus Lens (Patent Listed)
●
Selectable Sensitivity - High, Medium, or Low
●
Selectable Pulse Count - 1, 2 or 4
●
3 Step Angle Adjustment
●
Options
❍
❍
❍
CA-1W: Wall Mount Multi-Angle Bracket
CA-2C: Ceiling Mount Multi-Angle Bracket
BA-70: Backbox for Wireless Transmitter
http://www.optexamerica.com/products/cx70m.htm (2 of 4) [06/08/2000 12:27:20]
CX-70M Specifications Sheet
●
Versions
❍
❍
❍
❍
CX-70MV - Alarm Memory
CX-70MS - "Form C" relay output
CX-70MR (NC) - Battery operated, N.C. relay output
CX-70MR (NO) - Battery operated, N.O. relay output
Click Here To See The
CX-70M's Detection Patterns
Model
CX-70M
Power Input
6 ~ 18 V DC
Current Draw
20 mA max (6 ~ 18V DC)
Alarm Output
N.C. 28V DC 0.2A max.
Sensitivity
3°F (1.6°C) at 2 ft. / sec. (.6m / sec.)
Angle Adjustment
4.5° Vertical by 3 steps
Mounting
5 ~ 12 ft. (1.5m ~ 3.6m)
Operating Temperature
-4°F ~ +122°F (-20°C ~ +50°C)
Humidity
http://www.optexamerica.com/products/cx70m.htm (3 of 4) [06/08/2000 12:27:20]
Up to 95%
CX-70M Specifications Sheet
Pulse Count
Weight
Dimensions
1,2 or 4 20 ± 5 sec.
200g
5.51" x 3.94" x 2.68"
(140mm x 100mm x 68mm)
*Specifications an design are subject to change without prior notice.
S Version (Form C)
Model
CX-70MS
Alarm Output
Form C
Current Draw
40mA max. (6 ~ 18V DC)
Weight
200g
V Version (Alarm Memory)
Model
CX-70MV
Control Voltage
Current Draw
0 ~ 1V DC (ground)
25mA max. (6 ~ 18V DC)
Weight
200g
Battery Operation Version
Model
Alarm Output
CX-70MR (NC)
CX-70MR (NO)
N.C. 28V DC 0.2A max.
N.O. 28V DC 0.2A max.
Battery Saving
Circuit
Requires 2 min. non-activity for an alarm
Power Input
9V DC Alkaline Battery, Lithium Battery
Current Draw
Battery Life
Standby 15µA, On Alarm 10mA
2 years / Alkaline, 4 years / Lithium
Weight
http://www.optexamerica.com/products/cx70m.htm (4 of 4) [06/08/2000 12:27:20]
200g
CX-70M Detection Patterns
http://www.optexamerica.com/products/cx70mdpat.htm [06/08/2000 12:27:21]
SX-45C / SX-75C Specifications Sheet
In-Line Quad/DSP System
Multiple Step Protection
Up to now, your choice has been too much
sensitivity resulting in false alarms or too little
sensitivity resulting in no alarm. Optex has a
solution to this dilemma.
Introducing the "IN-LINE QUAD": Two pair of dual
elements (side by side) in one housing. Optex has
incorporated this feature in its new SX-45C and
SX-75C. The "IN-LINE QUAD" works together with
Double Signal Processing (D.S.P.) to cancel
environmental false alarms. With this new
technology, Optex has achieved the ultimate level of
reliability against false alarms, while maintaining
extremely high detection sensitivity and coverage.
●
In-Line Quad
●
Double Signal Processing (D.S.P.) Circuit
●
Noise Reduction Circuit
●
Pulse Count
●
RFI Protection
Incorporating D.S.P. and a special circuit which leads RF signals to ground. Field strength as much as
25 V/m.
●
6 to 18 VDC, 14mA Draw
(L Version, 20mA max)
●
Slimmest Design
Suitable anywhere especially where aethetics are a concern.
http://www.optexamerica.com/products/sx4575.htm (1 of 4) [06/08/2000 12:27:24]
SX-45C / SX-75C Specifications Sheet
Only one dual element is affected at a
time
Environmental
Both dual elements are affected at the
Hazards
same time and these signals are negated
RFI, Lights,
by the Simultaneous Signal Cancellation
Temperature Changes,
(S.S.C.) Circuit in the D.S.P. system.
Draft, etc.
Click Here To See The
SX-45C and SX-75C's Detection Patterns
http://www.optexamerica.com/products/sx4575.htm (2 of 4) [06/08/2000 12:27:24]
Alarm
No Alarm
SX-45C / SX-75C Specifications Sheet
Model
Detection
Method
Coverage
Detection
Zones
Mounting
Sensitivity
Detectible
Speed
LED Indicator
Alarm Period
Alarm Ouput
Tamper Switch
Pulse Count
SX-45C
SX-75C
Passive Infrared DSP System
45ft. x 45ft. (13.5m x
13.5m)
85° Wide Angle
75ft. x 20ft. (22.5m x 6m)
Long Range
80 Zones
32 Zones
Ceiling: Height 7 to 18 ft. (2.1 to 5.4m)
3°F (1.6°C) at 2ft./sec (0.6m/sec.)
1 ~ 6ft./sec.: (0.3 ~ 2.0m/sec.)
Alarm Indicator (switched option)
Alarm Memory (optional with L version)
2.5 ± 1 sec.
N. C., 28V DC 0.2A max.
N. C., Opens when body removed
20 ± 5 sec. Second delay
http://www.optexamerica.com/products/sx4575.htm (3 of 4) [06/08/2000 12:27:24]
SX-45C / SX-75C Specifications Sheet
Warm Up
Period
Power Input
Current Draw
Operating
Temperature
Environment
Humidity
RF
Interference
Weight
Approx. 40sec.
6 to 18V DC
14mA max. / 6 to 18V DC
-4°F to +122°F (-20°C to +50°C)
95% max.
No Alarm 25 V/m.
7.0oz (200g)
*Specifications are subject to change for improvement, without notice.
NOTICE: This product is designed to detect an intruder and send off a
signal. It is not a theft prevention unit. We cannot assume responsiblity for a
theft, should it occur.
Model
Alarm Memory
Current Draw
Weight
SX-45C-L
SX-75C-L
Control Voltage Signal: Positive
20mA max. / 6 to 18V DC
7.4oz (210g)
http://www.optexamerica.com/products/sx4575.htm (4 of 4) [06/08/2000 12:27:24]
SX-45C & SX-75C Detection Patterns
http://www.optexamerica.com/products/sx4575detp.htm (1 of 2) [06/08/2000 12:27:26]
SX-45C & SX-75C Detection Patterns
http://www.optexamerica.com/products/sx4575detp.htm (2 of 2) [06/08/2000 12:27:26]
SX-360Z Specifications Sheet
"ZOOM" Into Any Installation
Optex's Unique Zoom Function and Highly Dense,
Triple Element Detection Pattern, Provide
Unsurpassed Detection Performance at Any
Ceiling Height Up to 16 Feet!
OPTEX incorporates its latest technology into a new
generation of 360° detectors. The unique "Zoom"
mechanism makes the SX-360Z the most flexible
detector available. The 276 dense zones will provide
a 60 ft. (18m) circular detection area at any
installation height from 8 ft. to 16 ft. (2.4m to 5m)
with absolutely no dead spots. The SX-360Z's
compact design makes it the perfect detector for all
types of applications - residential and commercial,
large and small.
●
Highly Dense
Provides highly dense coverage with as many as 276 detection zones, eliminating dead spots over its
broad 60 ft. (18m) diameter detection area.
●
Zoom Function / Pattern Adjustment
The pattern angle can be variably adjusted. The special lens can be adjusted up and down by rotating
the housing cover of the "Zoom" mechanism. The angle adjustment can provide a 360° 60 ft. (18m)
diameter detection area at any ceiling height up to 16 ft. (5m) with high detection performance.
http://www.optexamerica.com/products/sx360z.htm (1 of 4) [06/08/2000 12:27:29]
SX-360Z Specifications Sheet
●
Patented Multi-Focus Lens
Creates zones with high vertical density for maximum detection sensitivity.
●
False Alarm Protection
❍
❍
❍
❍
❍
●
Other Features
❍
❍
●
RFI Protection
No alarm against field strengths levels exceeding 30v/m for the range of 100MHz to 1.2
GHz
Temperature Protection
No alarm in high, low and changing temperatures from -4°F to +122°F (-20°C to +50°C)
Noise Circuit Reduction
Selectable Pulse Count: 1,2,4
Selectable Sensitivity: High, Medium, Low
LED On/Off Switch
Warm-Up Indicator
Versions
❍
❍
❍
SX-360Z: Standard
SX-360ZS: Form C Relay
SX-360ZV: Initial Alarm Memory and Patented Double Conductive Shielding of Pyro
Element.
Click Here To See The
SX-360Z's Detection Patterns
http://www.optexamerica.com/products/sx360z.htm (2 of 4) [06/08/2000 12:27:29]
SX-360Z Specifications Sheet
Model
Detection Method
Coverage
Detection Zones
SX-360Z
Passive Infrared
ø60ft.(ø18m), 360° ZOOM
276 zones
Mounting
Ceiling Height: 8 ~ 16 ft. (2.4 ~ 5m)
Sensitivity
3° F (1.6° C) at 2 ft. / sec. (0.6 m / sec.)
Detectable Speed
1 ~ 6 ft. / sec. (0.3 ~ 1.8 m / sec.)
LED Indicator
LED blinks during warm-up period.
Alarm condition
Alarm Period
2.0 ± 0.5 sec.
Alarm Output
N.C.28V DC., 0.2A max.
Tamper Switch
N.C., Opens when cover is removed.
Pulse Count
20 ± 5 sec. 1,2 or 4
http://www.optexamerica.com/products/sx360z.htm (3 of 4) [06/08/2000 12:27:29]
SX-360Z Specifications Sheet
Warm-Up Period
Power Input
Approx. 20 sec. (LED Blinks)
6 ~ 18 V DC
Current Draw
13mA/(normal), 18mA/(max.)
Weight
Operating
Temperature
Environment
Humidity
7.90 oz. (224g)
-4°F ~ +122°F (-20°C ~ +50°C)
95% max.
RF Interference
No Alarm 30 V/m
*Specifications are subject to change without notice for improvement.
S Version (Form C)
Model
SX-360ZS
Alarm Output
Form C 28V DC 0.2A max.
Current Draw
30mA/(normal) 35mA/(max.)
Weight
7.94oz. (225g)
V Version (Alarm Memory)
Model
Alarm Memory
Initial Alarm Memory
Current Draw
Weight
RF Interference
SX-360ZV
SX-360Z(P)
Armed: 0 ~ 1V DC
Armed: +5 ~ 20V
DC
Max. 40 detectors
13mA/(normal), 25mA/(max.)
8.00oz. (227g)
No alarm 30 V/m
http://www.optexamerica.com/products/sx360z.htm (4 of 4) [06/08/2000 12:27:29]
SX-360Z Detection Patterns
http://www.optexamerica.com/products/sx360zdpat.htm (1 of 2) [06/08/2000 12:27:31]
SX-360Z Detection Patterns
http://www.optexamerica.com/products/sx360zdpat.htm (2 of 2) [06/08/2000 12:27:31]
Error Occurred While Processing Request
Error Occurred While Processing Request
Error Diagnostic Information
An error has occurred.
HTTP/1.0 404 Object Not Found
Please inform the site administrator that this error has occurred (be sure to include the contents of this
page in your message to the administrator).
http://www.optexamerica.com/products/moreinfo.cfm [06/08/2000 12:27:33]
Wireless 1000 Specifications Sheet
RC-10
Chimebox w/Relay
TD-10
Indoor/Outdoor Sensor Transmitter
RG-10
Single Relay Receiver
TS-10
Hand-Held Transmitter
The Next Generation of Our Wireless Annunciator System!
OPTEX now brings the benefits of its advanced wireless technology in the form of
greater RF transmission range and design versatility, to make your life more
comfortable and convenient. The Wireless 1000 Annunciator System can be installed
anywhere easily and quickly with no wiring. Whether it is for home or business, indoor
or outdoor, Wireless 1000 is the ideal choice for perimeter awareness and wireless
remote control.
Easy Installation - Indoor / Outdoor Use Long Radio Transmission Range - FCC Approved
http://www.optexamerica.com/products/wireless1000.htm (1 of 6) [06/08/2000 12:27:38]
Wireless 1000 Specifications Sheet
●
Wireless 1000 For Safety And Convenience
No more surprises!
Wireless 1000 monitors your property 24 hours a day to detect approaching vehicles and people, giving
you time to prepare.
No more missed visitors or deliveries!
Wireless 1000 serves as a welcome chime or perimeter alert for your home or shop.
No more hard to reach switches!
Wireless 1000 works as a convenient wireless switch for activating a variety of electric equipment (e.g.
doorstrikes / magnetic locks, lights, sirens, motors).
The Wireless 1000 Automatic Trigger
1 RC-10 and up to 4
TD-10 can also be used in conjunction with
lighting systems or anti-crime alert devices.
The Wireless 1000 Outdoor Protection
1 RC10 and up to 4 TD-10 can be installed
around your home entrances for perimeter
awareness.
The Wireless 1000 Remote Switch
1 RG-10 and up to 3 TS-10 can be used to
remotely open or close electronic locks
(electronic door strikes or magnetic locks).
●
Long RF Transmission and Reliable Operation
Newly developed non-directional antenna (TD-10)
All wireless transmitters have 'dead spots' within their transmission range. TD-10's improved antenna
http://www.optexamerica.com/products/wireless1000.htm (2 of 6) [06/08/2000 12:27:38]
Wireless 1000 Specifications Sheet
design greatly reduces 'dead spots' to make installation easier and increase reliability.
High gain antenna & narrow band tuning (RC-10 & RG-10)
Optimal antenna design and fine RF tuning achieve a high signal to noise rate, ensuring long range and
consistent operation.
"Best In Its Class" maximum transmission range
TD-10......................................... 1,000ft
TS-10.............................................700ft
(These measurements were obtained with receivers and transmitters mounted 7ft. above level ground
without obstructions. Natural and man-made obstructions and other environmental factors do shorten
transmission ranges.)
Simple, automated set-up
Setup is simple! Just two buttons perform all set up functions.
More than 8 million codes
Transmission codes are preset at the factory with over 8 million possibilities, virtually elimating the
possibility of interference or crosstalk.
Low battery signal
Low battery indication by tone (RC-10) and LED (all models) tells you when to replace batteries and
prevents malfunctions.
●
Design Versatility
- Specially designed sensor mounts easily on walls, ceilings, fenceposts, desktops, etc.
- Weatherproof design of sensor allows outdoor use.
- Two detection patterns: 50ft Long Range and 17ft. Fan Pattern
- Detection pattern adjusts easily for perfect aiming.
- Portable Hand-Held Transmitter (TS-10).
- TS-10 can be clipped to a belt, worn as a pendant, or mounted to a wall.
- Receivers mount on wall or desktop
http://www.optexamerica.com/products/wireless1000.htm (3 of 6) [06/08/2000 12:27:38]
Wireless 1000 Specifications Sheet
Model
Description
Power Source
Power Consumption
Chime Tone
Volume
Relay Output
RC-10
Chimebox w/ Relay
DC 9V (exclusive AC adapter)
Standby: 1W, Operating: 2W
3 tone & 1 alarm (optional)
Adjustable: 0~80dB / 5 levels
(Continuous zone: max.)
Max. 1A / 50 VAC or 1A /
24VDC
http://www.optexamerica.com/products/wireless1000.htm (4 of 6) [06/08/2000 12:27:38]
RG-10
Single Relay Receiver
12 ~ 24V AC/DC
Standby: 30mA, Operating: 80mA
Max. 1A / 50 VAC or 1A / 24VDC
Wireless 1000 Specifications Sheet
Selectable: off/1/5/30/60sec/utility
output mode
Power Indicator: Green LED
Status Indicator
Zone Indicator: red LED x 3
Radio Frequency
418mHz
Operating Temperature
15°F ~ 104°F (-10°C ~ 40°C)
Installation Location
Indoor
Weight
6.0 oz. (170g)
AC adapter x 1
Accessories
Mounting Screw x 1
Output Timer
Model
Description
Detection Method
TD-10
Sensor Transmitter
Passive Infrared
50ft (15m) long range
Detection Pattern
17ft (5m) fan pattern
90° vertically & ±5° horizonally
Angle Adjustment
or
±5° vertically & 90° horizonally
Power Source
9V: alkaline battery
Approx. 2 years
Battery Life
[250 / day at 70°F (20°C)]
Status Indicator
Red LED
Radio Frequency
418mHz
Operating Temperature
15°F ~ 120°F (-10°C ~ 50°C)
Water Resistance
IP54
Installation Location
Outdoor / Indoor
Weight
6.3 oz. (180g)
Accessories
Mounting Screw x 2
Selectable: 1/5/30/60sec
Power Indicator: Green LED
Zone Indicator: red LED x 3
418mHz
15°F ~ 104°F (-10°C ~ 40°C)
Indoor
4.2 oz. (120g)
Mounting Screw x 1
TS-10
Hand-Held Transmitter
Push Button
3V: AA x 2 alkaline battery
Approx. 2 years
[100 / day at 70°F (20°C)]
Red LED
418mHz
15°F ~ 120°F (-10°C ~ 50°C)
IP43
Outdoor / Indoor
1.4 oz. (40g)
Belt Clip x 1
Other Applications
RC-10
RG-10
Chime Box Chime Box
Reciever w/ Single Relay
Relay
Receiver
X
X
X
X
Driveway Annuciator
Entry / Walkway Chime
Wireless Doorbell
Warehouse Delivery Areas
http://www.optexamerica.com/products/wireless1000.htm (5 of 6) [06/08/2000 12:27:38]
TD-10
Indoor / Outdoor
TS-10
Sensor
Hand-Held
Push
Fan
Long
Button
(wide)
Range
Angle
X
X
X
X
X
X
Wireless 1000 Specifications Sheet
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Construction Site Guard
Monitor hard to see or shoplifting
prone items
Inside display cases at jewelry
stores
Anti-vandalism at art galleries
Loss Prevention: Monitor
department store dressing rooms
and fitting rooms
Annunciate unauthorized use of
emergency exits
Signaling for drive-up window
Location finder for blind
Delivery doors, roll-up, or bay
doors
Monitor Supplies: Place in supply
room or closet
Release door strike or magnetic
lock
Annuciate activity at CCTV
camera
http://www.optexamerica.com/products/wireless1000.htm (6 of 6) [06/08/2000 12:27:38]
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
WT-110 WonderTrack Specifications Sheet
Never Fails To Capture That
Critical Moment
- Instant high resolution digital recording
- High Tech Digital CCTV Technology
- No Maintenance Costs
- Versatile applications for Security and Non Security
purposes
- Easy to use
- 4 channel Switcher
Read a Review From PSI
Professional Security Installer Magazine
●
Optex has the ideal system utilizing sensing technology and high-tech Digital Visual recording.
Do you want to see the actual picture when a burglar entered your premises? WonderTrack can take a picture
at the crucial moment, using either the new Optex covert camera with Passive Infrared Detector (PIR), or any
other normal camera with PIR. Existing systems using Time Lapse Video recorders are unable to capture
those important moments. Time Lapse requires a few seconds to go from standby to record, often missing
vital pictures. With WonderTrack no such delay occurs.
http://www.optexamerica.com/products/wt110.htm (1 of 6) [06/08/2000 12:27:44]
WT-110 WonderTrack Specifications Sheet
●
Maintenance Free
Do you suffer from expensive maintenance charges associated with Time Lapse Video? Is there no
alternative recording system to Time Lapse? Optex has one. WonderTrack from Optex offers you an
alternative solution, a maintenance free, high technology digital CCTV recording unit, offering user-friendly
operation at an incredibly affordable price.
●
Save Labor Costs
How many hours does it take to check the recorded tapes from a Time Lapse Video? WonderTrack can be
programmed to take instant pictures in the event of an alarm, avoiding the requirement for constant
recording.
WonderTrack provides an incredibly quick and easy system to enable rapid search of its indexed picture
storage, saving on labour costs and the waste of precious time.
●
Compact and Easy To Use
WonderTrack is a compact and lightweight unit which can be placed on a desktop or mounted on a wall.
Easy to install and operate, it does not require the use of a complicated PC or software to set up the system.
●
Picture Index For Quick Search
WonderTrack indexes all pictures with such details as the camera number, date/time, and alarm mode (on or
http://www.optexamerica.com/products/wt110.htm (2 of 6) [06/08/2000 12:27:44]
WT-110 WonderTrack Specifications Sheet
off) in order to allow easy searching.
●
High Speed Compression with Good Black and White Picture Quality
The combination of an advanced micro-chip and JPEG chip ensures high-speed data compression to the
JPEG file within one second. (Speed varies according to picture resolution.)
●
Supports Selective Dual Resolution Modes From Large Memory Storage
Standard visual formats utilizing JPEG in high and standard resolution modes. Standard 8 MB memory
provides more than 330 pictures in high resolution. This can be further expanded up to 747 pictures by
adding a maximum of 12 MB of optional memory. Overwrite memory mode enables endless recording.
●
4-Channel Switcher Function
Up to four cameras can be connected to the WT-100 and support the EIA/CCIR format of the camera data
input. Each camera channel has its own alarm input allowing applications such as switching channels for
monitoring, or recording visual data in the event of an alarm.
●
WonderTrack's Versatile System Offers Several Modes To Capture The Critical Moment
Interval Mode
This setting enables constant recording in programmed time intervals with sequential chain shots on Alarm.
Overwrite selection can be disabled to protect all pictures recorded in memory.
Multi-Angle Mode
This option allows sequential pictures to be taken by more than one camera when only detection by one
camera has occurred. This unique feature allows pictures of the same object to be captured from
multi-angles.
http://www.optexamerica.com/products/wt110.htm (3 of 6) [06/08/2000 12:27:44]
WT-110 WonderTrack Specifications Sheet
Pre-Alarm Mode (only Channel 1)
Enables a selected number of pictures monitored before an alarm to be safely saved.
●
Integration of Alarm & CCTV
Unique double alarm relays of the DC-20 allow connection with any security control panel and WT-100 unit.
An alarm is used for the security control panel which simultaneously triggers the WT-100 to capture pictures
at the critical moment. The WT-100 can be connected to a security panel, allowing the recording modes of
the WT-100 to be switched by remote control.
http://www.optexamerica.com/products/wt110.htm (4 of 6) [06/08/2000 12:27:44]
WT-110 WonderTrack Specifications Sheet
Model
WT-110E
http://www.optexamerica.com/products/wt110.htm (5 of 6) [06/08/2000 12:27:44]
WT-110C/CK
WT-110 WonderTrack Specifications Sheet
Power Supply
Current Draw
Video
Signal Format
Video Input
Sampling Resolution
Alarm Command
Alarm Input
Alarm Output
Arming Mode Input
Memory
Compression Method
Interval Time
Memory Size
Number of Pictures (approx)
Physical
Dimensions
Weight
Operating Temperature
100-120VAC 60Hz
230VAC 50Hz/240VAC 50Hz
0.6A (DC 7V)
EIA black/white
CCIR black/white
4 camera composite 1.0V p-p±10% 75ohm
640 h x 240 v x 8 bits (b/w)
768h x 288v x 8 bits (b/w)
Field Mode
4 relay inputs, 1 per camera, N.C., N.O. Programmable
1 relay output 2±0.5 sec/picture, N.C., N.O. 28V DC 0.2A max
1 relay, open corrector matching
JPEG
1.5 sec (minimum) - 10 sec Programmable
8mb (max. 12mb with additional memory)
High: 330 pictures (add: 495 pictures) / Standard: 495 pictures (add:
745 pictures)
9.9"w x 7.1"h x 1.6"d (250mm x 180mm x 41mm)
2 lb (0.8 kg)
32°F tp 104°F (0°C to 40°C)
http://www.optexamerica.com/products/wt110.htm (6 of 6) [06/08/2000 12:27:44]
April 1999
£3.50
Professional Security Installer
INTELLIGENT
IMAGES
THE ROLE OF THE
PC IN CCTV
PSI PRODUCT
AWARD 1999
VOTING CONCLUDES
REGULATION
RUMORS ABOUND
IFSEC 1999
OUR PREVIEW STARTS HERE
WIN!
A COLOUR SENTRY FROM
BC ACCESS CONTROL
TESTED
SAND TO
THE ARABS?
DO YOU HAVE A PROFESSIONAL
APPROACH TO SALES?
KEEPING
TRACK
Professional
Test
Optex Wondertrack WT-110 digital image storage unit
The idea behind digital storage is
all well and good. in simple
terms, it involves taking video
images, and storing them on
some form of digital media rather
than magnetic tape. The benefits
are that images become easier to
manage, and quicker to locate.
There is not always a need to
filter through hours of minimal
action to find one incident of
interest. Other benefits include
the ability to instantly start
recording images when an alarm
input is received, rather than
when a tape machine clicks into
action. Pre-alarm images can
also be achieved, simply by
creating a buffer of information
which overwrites itself. When an
incident occurs, the entire buffer
is simply moved to a secure part
of the system.
The question many will be
asking is why, if digital storage is
such a good idea, are so many
engineers wary of making a
commitment to the technology.
The answer is simple. There are
a number of ways digital
technology can go, and despite
all manufacturers claiming their
system is the one the others will
follow, no one really knows
where this technology will go in
the future. Add this to a number
of scare stories about the
technology, and the hesitancy of
You cannot even approach the
concept of CCTV installation
nowadays without a fistful of
companies screaming about
the latest greatest digital
recording system. Many of
them will tell you that for a
few thousand pounds they can
furnish you with the latest in
high tech wizardry, and your
life will never be the same
again. Others will caution you
about emerging technologies,
and tell you theirs will become
the industry standard. Indeed,
many manufacturers of digital
storage devices spend more
time slagging each other off
than they do actually showing
the professional installer the
benefits which their system
can offer. Now intruder
detection specialist Optex has
entered the arena with a
digital image storage unit.
This cost-effective device is
designed to offer a credible
tool to professional installers,
but does it succeed? PSI takes
a long hard look at the
WonderTrack to see!
many becomes understandable.
The final hurdle to overcome is
that of price. In short, engineers
are unwilling to gamble on
equipment with a higher price tag.
Perhaps someone should squeeze
all the benefits out of the
technology, whilst keeping the
product at an affordable price.
This would allow engineers to sell
advanced systems without taking
expensive risks. Right on cue, it’s
time to look at the Optex
Wondertrack.
The right direction
The Wondertrack is billed as a
digital image storage unit,
although that certainly does not
tell the whole story. The system
can support up to four cameras
and four alarm inputs, and
captures images onto a memory
card, which is removable, in the
event of an alarm. Pre-alarm
images can also be obtained, and
the system can be easily integrated
with a traditional intruder alarm
system. Stored images are time
and date stamped, which is useful
for evidential purposes. The most
impressive thing about the
Wondertrack is its enormous
flexibility, and the diverse number
of applications in which it can be
used. Although the initial response
of many is to integrate it with an
intruder detection system and use
it to verify alarms, this is only
scratching the surface. it is a case
of the longer you think about it,
the more the application potentials
seem to grow.
The features of the system are
impressive in themselves. The
unit provides digital recording and
playback of alarm images, and
these can be stored in either
standard or high resolution
formats. In standard resolution,
The memory card
allows images to be
saved, and is
available with
different memory
capacities.
the system can store
up to 500 images on
an 8Mb memory
card (supplied with
the system). If you
require a higher
number of images,
then
a
16Mb
memory card is available.
Obviously higher resolution
images will take up more space,
although the mode used will be
very dependent upon the
application.
Probably the best way to get
an understanding of the flexibility
on offer is to consider the
operation of the unit. There are
three recording modes, known as
Interval, Channel 1 pre alarm, and
Multi Angle. Interval recording
means that the system will record
one image from the camera on a
regular basis without an alarm
input. This can be set to be every
10, 30, 60, 120, 180, 240, 300 or
360 seconds, or can be switched
off so the unit only responds to
alarm events. In the event of an
alarm activation, the unit will
switch to recording one image for
predetermined amount of images in a time window which can be set
between 1 and 10 seconds. The
system can be set so that when the
memory card is full, it stops
recording, or alternatively it can
over-write itself, ensuring that you
always have a full card of
previous images.
The Channel 1 pre-alarm
setting allows you to program the
system to record alarm images, as
in Interval mode, but without the
constant non-alarm images and
with the addition of pre-alarm
images up to 7 in standard
resolution or four in high
resolution - on channel 1.
Unfortunately this cannot be set
for the additional channels.
Finally, the Multi Angle mode
allows the system to be set to
record a predetermined number of
images between 1 and 64 from
each input in the event of an alarm
activation.
There are also three operating
modes, These are Record, Play
and Thru. The first two are
obviously self explanatory, and
are used to record and play back
images. The Thru mode is
effectively used for monitoring
the cameras whilst a site is
operations. Subsequently, cameras
can be set to switch, with the
output displayed on a monitor.
Each channel can be given a
specific dwell time, making it
easier to program the system to
respond to the needs of the site. It
is also possible to deactivate the
alarm record functions on specific
channels if required. This ability
only covers Thru mode, and will
not therefore inhibit recording
when the system is set to Record
mode. As such, this can be seen as
a day function if 24 hour alarmactivated protection is not required.
Finally, each channel can be
set to one of two Record
Conditions, depending upon which
recording mode is used. For
example, in Interval mode,
channels can be either set for alarm
recording only (as a single shot) or
a combination of alarm and
interval recording. In Channel I
pre-alarm mode, a selection can be
made between pre-alarm recording
and single shot recording, or prealarm and full alarm recording.
Finally, in Multi Angle mode, the
system can be set to record from
the channel in alarm, or from all
channels when an alarm activation
occurs.
These conditions are selected
from channel switches, which also
give the option for a particular
input to be switched off. In order to
prevent tampering, the switches
themselves can be disabled, with
settings made through an onscreen menu. This is certainly a
benefit when considering the
system’s security abilities.
Now, the above might seem
confusing, but you can believe us
when we say it’s a fair bit clearer
than it will be when you first read
the manual. The instructions are
probably the worst bit of the
product,
and
we
would
recommend that any installer who
tries out a Wondertrack spends a
few hours prior to installation
setting one up in a workshop and
going through the various settings
and procedures, It is a complex
piece of equipment with a number
of possible settings, but once you
get a clear idea of what is
happening, it does suddenly all
become very simple!
Design of the unit shows that
Optex have carefully considered
the needs of engineers.
Installation
Installation of the system is
simple, and Optex have included
some very nice touches, which at
least show that the requirements of
security installers have been
considered. The system comes as
close to the ‘Plug and play’
mentality as such an advanced
system can, and whilst not
requiring any specific engineering
skills, does rely upon a good
understanding of applicationspecific security system design if
the fullest potential is to be
obtained from the Wondertrack.
The parts of the system which
need to be accessed by the
engineer are hidden beneath a
plain cover which is retained by a
side-mounted securing screw.
Once the flap is lifted away, there
are two connector blocks, One of
these is for alarm inputs and one is
for alarm outputs, There are four
BNC connectors for video inputs.
Power is supplied via a PSU which
connects to an integral connector.
The only other items under the
cover are a memory reset and a
bank of DIP switches, only two of
which are used, One selects colour
or monochrome recording, and the
other controls the alarm out
functions.
Performance
Once the programming is set up
correctly,
the
Wondertrack
operates faultlessly. Image quality
is good, and the various settings
meet their specifications. There is
a slight difference on some of the
timings, but this has more to do
with the image processing time
than anything else, and is so slight
as to not be noticeable unless you
make a conscious effort to try and
spot it!
The standard resolution setting
is ideal for general surveillance
work, although if we were to use
the system as a tool capturing
images for evidential purposes, the
extra added by the higher
resolution setting is worthwhile,
The difference in the number of
recordings held by the system is
not great enough to be a major
issue. Capacity falls by around 30
per cent when the higher
resolution is employed. The prealarm function works well, and
although the frequency of nonalarm images in the Interval
recording mode was a bit hit or
miss, there were enough other
options to keep us happy. One of
the things to remember with the
Wondertrack is that if you are not
too keen on the choices offered by
one setting, there is bound to be
another setting which will achieve
your goal!
In conclusion
The Optex Wondertrack does
something which not many image
storage systems do, and that is it
employs digital CCTV technology
as a security product exploiting the
available benefits, rather than
trying to offer an alternative to
analogue recording machines.
With a price which falls well
under E500, the WT-110 offers
professional security installers a
tool which can ensure a higher
level of security.
The Wondertrack is recommended for professional engineers, and
is sure to become a success given
the huge range of applications
which it can be used in. The
system is innovative and well
thought out, and shows that digital
technology can actually become a
mainstream product today!
psi
RATINGS
Optex WonderTrack
PRODUCT
Product Design
Build Quality
Ruggedness
OPERATION
General function
CCTV functions
Ease of use
Instructions
PERFORMANCE
Video Quality
Recording Options
Excellent
Average
Inferior
As seen in the April 1999 edition of PSI - Professional Security Installer magazine.
Y2K Letter
Y2K Project
1845 W. 205th St.
Torrance, Ca. 90501
310-533-1500
310-533-5910 fax
Revised 4/12/99
GENESYS Series Control Panels
While the GENESYS series control panels are microprocessor based alarm systems, they do not have
any functions that are dependent upon the a specific time/date and therefore will operate as intended
on January 1, 2000 and also on Leap Year Day, February 29, 2000.
MDC16CD and MDC16CE
While the MDC16CD and MDC16CE series control panels are microprocessor based alarm systems,
they do not have any functions that are dependent upon the a specific time/date and therefore will
operate as intended on January 1, 2000 and also on Leap Year Day, February 29, 2000.
MDC-16CET- MDC16ETX
YEAR 2000
The project engineers assigned to develop this product line were able to encode into the operating
software the ability to maintain perpetual time. The date will automatically roll over to the year 2000.
The keypad will indicate the turn of the century when programmed to display the clock as 01/01/:0 and
all time related functions will operate as intended on January 1, 2000. However you must change the
date format year to read 00 after the turnover for the alarm system to correctly recognize Leap Year
Day (February 29, 2000). The keypad display will change from February 28, 2000 to March 1, 2000
should the :0 format be left on the display after January 1, 2000.
YEAR 2001
In the event that the alarm system lose both AC power and standby power in the year 2001, the
installer programmed schedules that may have been used to control automatic arming and a weekly
self test will shift by one day. What this means is the schedule set for a Saturday will now become the
schedule for Sunday. The remedy for this situation is to either re-download the program into the panel
after the power has been re-set in the year 2001 or to request new operating software from Optex
America.
●
To update the software, Optex America must know if the control panel version is the MDC16ET or
the MDC16ETX and the operating software revision. To obtain this information the control panels will
have a label on the perforated metal shield located in the center of the PCB assembly that will indicate
if the panel is an ET or ETX and will also be followed by REV. X (X indicating the software revision).
●
●
Examples:
Model MDC16c
TYPE ET REV G
or
Model MDC16c
TYPE ETX REV B
●
This situation will only affect the alarm system if the schedules have been enabled for use with your alarm
system. We recommend that you contact your alarm company to positively identify if this option has been
enabled.
●
MDC 16 ET REVs A through L (order kit number 70259 - cost $10.00)
MDC 16 ET REVs M or N (order kit number 70258 cost - $10.00)
MDC 16 ETX REVs A through G (order kit number 70257 - cost $10.00)
●
●
Note: all of the above kits will include updated plug-in software and a manual on how to insert the new
http://www.optexamerica.com/news_articles/y2kdoc.htm (1 of 3) [06/08/2000 12:27:54]
Y2K Letter
software.
Warning: Damage will occur if the software is incorrectly installed and will void all Optex America
warranties. We strongly recommend that you contact your alarm company for assistance.
SMDC Control Panel
The project engineers assigned to develop this product line were able to encode into the operating
software the ability to maintain perpetual time. The date will automatically roll over to the year 2000.
The keypad will indicate the turn of the century when programmed to display the clock and date as
01/01/00. All time related functions will operate as intended on January 1, 2000 and Leap Year Day
February 29, 2000.
MDC8 Series Control Panels (MDC8C - MDC8CE)
While the MDC8 series control panels are microprocessor based alarm systems, they do not have any
functions that are dependent upon the a specific time/date and therefore will operate as intended on
January 1, 2000 and also on leap Year Day February 29, 2000.
TSS Control Panel
The project engineers assigned to develop this product line were able to encode into the operating
software the ability to maintain perpetual time. The date will automatically roll over to the year 2000.
The keypad will indicate the turn of the century when programmed to display the clock and date as
01/01/00. All time related functions will operate as intended on January 1, 2000 and Leap Year Day
February 29, 2000.
SPT Series Multiplex Transponders
While the SPT series multiplex transponders are microprocessor based alarm systems, they do not
have any functions that are dependent upon the a specific time/date and therefore will operate as
intended on January 1, 2000 and also on Leap Year Day, February 29, 2000.
SPC 5000 Multiplex Central Station Receiver
The SPC 5000 central station receiver is also microprocessor based that makes use of an internal
calendar which is based on a Julian calendar year. The SPC5000 is not effected by the Year 2000 and
therefore will operate as intended on January 1, 2000 and also on Leap Year Day, February 29, 2000.
V-300 Series Central Station Receivers (V300A - V300APT)
Optex Inc. (formerly The Morse Security Group) engineering department developed the V-300 around a
real time operating system. The project engineers assigned to develop this product line were able to
encode into the operating software the ability to maintain perpetual time. The date will automatically roll
over to the year 2000. The V-300 will indicate the turn of the century when programmed to display the
clock as 01/01/:0 and all time related functions will operate as intended on January 1, 2000. However
you must change the date format year to read 00 after the turnover for the V-300 to correctly recognize
Leap Year Day (February 29, 2000). The V-300 display will change from February 28, 2000 to March 1,
2000 should the :0 format be left on the display after January 1, 2000.
TRAP & TRT5200 (Touch Response Alarm Processor and Trap Transponders)
The project engineers assigned to develop this product line were able to encode into the operating
software the ability to maintain perpetual time. The date will automatically roll over to the year 2000.
The keypad will indicate the turn of the century when programmed to display the clock and date as
01/01/00. All time related functions will operate as intended on January 1, 2000 and Leap Year Day
February 29, 2000.
http://www.optexamerica.com/news_articles/y2kdoc.htm (2 of 3) [06/08/2000 12:27:54]
Y2K Letter
MDC Series Long Range Radio Transmitters. (MDC4 & 8RF - RF-RM1 - RF-8000)
While the MDC Series Long Range Radio Transmitters are microprocessor based alarm systems they
do not have any functions that are dependent upon the a specific time/date and therefore will operate
as intended on January 1, 2000 and also Leap Year Day, February 29, 2000.
All Optex Inc. Sensors (PIRs, Photobeams, Active Sensors, Light Controls, etc.)
While the Optex Inc. line of sensors are microprocessor based, they do not have any functions that are
dependent upon the a specific time/date and therefore will operate as intended on January 1, 2000 and
also on Leap Year Day, February 29, 2000. Should the installation employ timing functions that are
related to the motion sensors, the time functions are controlled by the alarm system not the peripherals.
Please feel free to contact our Technical Support at 310-533-1500 or you may contact your alarm installation
company should you have further questions and/or concerns regarding this matter.
Technical Support / Team Y2K
Optex Inc.
Return To Home Page
http://www.optexamerica.com/news_articles/y2kdoc.htm (3 of 3) [06/08/2000 12:27:54]
OptexAmerica News
Optex News: June 8, 2000
New Products
· Coming Soon!
· Coming Soon!
· Wireless 1000
· DC Series CCTV Cameras
· WonderTrack Digital Recorder
· WonderTrack Reviewed In PSI Magazine
Factory Automation
News
Company News
Hot Topics
Alarm News
· Coming Soon!
Door News
· Coming Soon!
http://www.optexamerica.com/indexes/news.cfm [06/08/2000 12:27:56]
· Y2K Letter
Long Range Wireless 1000 Annunciator System
1845 W. 205th St.
Torrance, Ca. 90501
310-533-1500
310-533-5910 fax
Internet/E-mail: Optex@westworld.com
Long Range
Wireless 1000 Annunciator System
Click Here for more info...
Optex's Long Range WIRELESS 1000 Annunciator System reliably alerts users to the approach of
visitors, provides outdoor perimeter protection and other 'light' security applications. Both the PIR
transmitter (TD-10U) and the push button (TS-10U) transmitter are fully weatherproof for indoor or
outdoor use. The receiver (RC-10U) has three tones to identify the transmitter sending the signal, a
latching alarm zone, and a 1 Amp form C relay which is ideal for activating door strikes, lights, CCTV,
and countless other uses.
Return To Home Page
http://www.optexamerica.com/news_articles/wire1000a.htm [06/08/2000 12:27:56]
DC Series CCTV Cameras
DC Series
CCTV Cameras
1845 W. 205th St.
Torrance, Ca. 90501
310-533-1500
310-533-5910 fax
Internet/E-mail: Optex@westworld.com
Click Here for more info...
Integrating advanced solid state camera technology with high quality PIR detectors provides an efficient
and attractive solution to interior security requirements. Optex's DC Series covert cameras feature high
sensitivity CCD devices, automatic gain control, and high speed electronic shutters to provide clear vision
with as little as 0.5 lux lighting. The commercial quality PIR has Quad Zone Logic for superior false
alarm immunity and separate relays for alarm and CCTV signaling.
Return To Home Page
http://www.optexamerica.com/news_articles/cctv_news.htm [06/08/2000 12:27:57]
WonderTrack - 4 Zone Digital "Catch" Recorder
1845 W. 205th St.
Torrance, Ca. 90501
310-533-1500
310-533-5910 fax
Internet/E-mail: Optex@westworld.com
Wondertrack
4 Zone Digital "Catch" Recorder
Click Here for more info...
Winner of Best New Product of Show Award at ISC West 1999
WT-110, a 4 zone sequential switcher and digital event recorder brings digital recording to new 'low cost'
markets. Crystal clear, digital images from up to 4 cameras are stored to 8 or 16MB smart media cards for
easy retrieval. Since there's no tape or recording heads to wear-out, WT-110 provides many years of
reliable and easy operation. Built-in alarm system interface provides customers with alarm event
recording.
Return To Home Page
http://www.optexamerica.com/news_articles/wondertrack_news.htm [06/08/2000 12:27:58]
Optex Message Center
Send an e-mail message to:
Service
Technical Support
Web Master
Optex Administration
http://www.optexamerica.com/send_email.cfm [06/08/2000 12:27:59]
Password Required To Enter Download Area
Please enter the required password
to enter the secured area:
Click Here to Continue
If you do not know the password, please call (800) 966-7839
and ask for the technical support department
(between the hours of 8am to 5pm (PST), Monday through Friday)
http://www.optexamerica.com/security/sec_dealer.cfm [06/08/2000 12:28:01]
Locate The Security Sales Representative In Your Area
[FOR CANADA: CLICK HERE]
Click On The State In Which You Are Located
To Find The Sales Representative For Your Area
http://www.optexamerica.com/security/sec_sales_reps/sec_usamap.cfm [06/08/2000 12:28:09]
Sales Representative for Canada
The Sales Representative For Canada is:
Name: Jay Vaare-Lamoureux
Title: Canadian Regional Sales Manager
Phone Number: (800) 966-7839
Fax Number: (310) 533-5910
Return To Previous Page
http://www.optexamerica.com/security/sec_sales_reps/sec_cansalesrep.htm [06/08/2000 12:28:10]
Security Sales Representatives in the Western Region
The Security Sales Representative For This Section of the United States is:
SECURITY
Name: Griff Kimble
Title: Western Regional Sales Manager
Phone Number: (800) 966-7839
Fax Number: (310) 533-5910
Return To Previous Page
http://www.optexamerica.com/security/sec_sales_reps/sec_west.htm [06/08/2000 12:28:11]
Security Sales Representatives in the South Central Region
The Security Sales Representative For This Section of the United States is:
SECURITY
Name: Keith Daulton
Phone Number: (800) 966-7839 Ext. 205
Fax Number: (310) 533-5910
E-mail Address: kdaulton@optexamerica.com
Return To Previous Page
http://www.optexamerica.com/security/sec_sales_reps/sec_southcental.htm [06/08/2000 12:28:12]
Security Sales Representatives in the Southeast Region
The Security Sales Representatives For This Section of the United States are:
SENSORS
3565 Hutchinson Road, Suite 400, Cumming, GA 30040
Phone Number: (770) 887-2844 . Toll Free: (800) 333-2844 . Fax Number: (770) 889-7431
WWW Home Page: http://www.SecuritySolutions-ga.com
E-Mail Address: SecuritySolutions@worldnet.att.net
Outside Sales Staff:
Management - Gust Askounis, President & Ben Jackson, Vice President of Sales
Florida Sales Manager - Jack Green (States covered: FL)
Mid Atlantic Sales Manager - Lise Carper (States covered: VA, WV, MD, DE, DC, PA)
Mid South Sales Manager - Rod Warren (States covered: GA, AL, MS, NC, SC, TN)
Inside Sales and Administrative Support:
Cindy Askounis - Vice President, Business Development
Amy Drews - Executive Assistant, Business Development
Joyce DiVirgilius - Executive Assistant, Sales
Maureen Starks - Senior Account Manager: GA, NC, and SC and outside sales for PR
Connie Haman - Senior Account Manager: FL, AL, MS, TN
Maria Rovinelli - Senior Account Manager: WV, VA, MD, DE, DC, PA
http://www.optexamerica.com/security/sec_sales_reps/sec_southeast.htm (1 of 2) [06/08/2000 12:28:13]
Security Sales Representatives in the Southeast Region
CONTROL PANELS
Name: Jay Kessel
Phone Number: (310) 533-1500 Ext. 101
Fax Number: (310) 533-5910
E-mail Address: jkessel@optexamerica.com
Return To Previous Page
http://www.optexamerica.com/security/sec_sales_reps/sec_southeast.htm (2 of 2) [06/08/2000 12:28:13]
Employee Database Test
Employees are listed alphabetically.
Agabiti, Joe
Eastern Regional Sales Manager, Automatic Door
Division
Division: Automatic Door Division
Phone: (310) 533-1500 x202
E-mail: jagabiti@optexamerica.com
Armstrong, Norma
Office Manager
Division: Administration
Phone: (310) 533-1500 x103
E-mail: narmstrong@optexamerica.com
Chheda, Nalin
R&D Manager
Division: Engineering and Production
Phone: (310) 533-1500 x130
E-mail: nchheda@optexamerica.com
Galindo, Claudia
Sales Coordinator
Division: Administration
Phone: (310) 533-1500 x100
E-mail: cgalindo@optexamerica.com
http://www.optexamerica.com/employees/allemployees.cfm (1 of 6) [06/12/2000 19:14:30]
Employee Database Test
Hernandez, Manuel
Shipping / Receiving
Division: Administration
Phone: (310) 533-1500 x151
E-mail: mhernandez@optexamerica.com
Kessel, Jay
Vice President, Sales
Division: Security Division
Phone: (310) 533-1500 x101
E-mail: jkessel@optexamerica.com
Kida, Masaya
Senior Administrative Manager
Division: Automatic Door Division
Phone: (310) 533-1500 x163
E-mail: mkida@optexamerica.com
Kokobo, Mac
Inside Sales and Marketing
Division: Security Division
Phone: (310) 533-1500 x142
E-mail: mac@optexamerica.com
Kreider, Mark
Marketing Director
Division: Security Division
Phone: (310) 533-1500 x147
E-mail: mkreider@optexamerica.com
http://www.optexamerica.com/employees/allemployees.cfm (2 of 6) [06/12/2000 19:14:30]
Employee Database Test
Kuroda, Art
Vice President
Division: Administration
Phone: (310) 533-1500 x104
E-mail: kuroda@optexamerica.com
LaChere, Michael
Vice President, CFO
Division: Administration
Phone: (310) 533-1500 x106
E-mail: mlachere@optexamerica.com
Lara, Jamie
Design Engineer
Division: Engineering and Production
Phone: (310) 533-1500 x133
E-mail: jlara@optexamerica.com
Morioka, Ned
Director of Consumer Division
Division: Security Division
Phone: (310) 533-1500 x107
E-mail: nmorioka@optexamerica.com
Mosquera, Ivan
Export
Division: Security Division
Phone: (310) 533-1500 x144
E-mail: imosquera@optexamerica.com
http://www.optexamerica.com/employees/allemployees.cfm (3 of 6) [06/12/2000 19:14:30]
Employee Database Test
Mott, Eric
Technical Support Manager
Division: Technical Support
Phone: (310) 533-1500 x120
E-mail: emott@optexamerica.com
Payton, Gerald
Repairs
Division: Administration
Phone: (310) 533-1500 x154
E-mail: gpayton@optexamerica.com
Quick, Shauna
Accounts Payable, FA Division Assistant and
Inventory Control Administrator
Division: Administration
Phone: (310) 533-1500 x105
E-mail: squick@optexamerica.com
Rivera, Jorge
Technical Support, Spanish & English
Division: Administration
Phone: (310) 533-1500 x124
E-mail: jrivera@optexamerica.com
Rogers, Kevin
Western Regional Sales Manager, Automatic
Door Division
Division: Automatic Door Division
Phone: (310) 533-1500 x161
E-mail: krogers@optexamerica.com
http://www.optexamerica.com/employees/allemployees.cfm (4 of 6) [06/12/2000 19:14:30]
Employee Database Test
Sanchez, Louise
Accounts Receivable
Division: Administration
Phone: (310) 533-1500 x102
E-mail: lsanchez@optexamerica.com
Sterling, Joshua
Sales Promotion & Marketing
Division: Technical Support
Phone: (310) 533-1500 x140
E-mail: jsterling@optexamerica.com
Takei, Hiro
General Manager, Sales Division
Division: Factory Automation Division
Phone: (310) 533-1500 x137
E-mail: hiro@optexamerica.com
Tharee, Mike
Production Manager
Division: Engineering and Production
Phone: (310) 533-1500 x150
E-mail: mtharee@optexamerica.com
Van Winkle, Paul
Product Manager
Division: Security Division
Phone: (310) 533-1500 x146
E-mail: pvanwinkle@optexamerica.com
http://www.optexamerica.com/employees/allemployees.cfm (5 of 6) [06/12/2000 19:14:30]
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising