Airwell | AWSI-HKD009-N11 | Service manual | Airwell AWSI-HKD009-N11 Service manual

Airwell AWSI-HKD009-N11 Service manual
HKD DCI Series
Indoor Units
Outdoor Units
AWSI-HKD009-N11
AWSI-HKD012-N11
AWSI-HKD018-N11
AWSI-HKD024-N11
AWAU-YKD009-H11
AWAU-YKD012-H11
AWAU-YKD018-H11
AWAU-YKD024-H11
REFRIGERANT
REFRIGERANT
R410A
SM HKD DCI 1-A.1 GB
HEATPUMP
APRIL, 2014
CONTENTS
1. Precaution .................................................................................................................................................... 3
1.1 Safety Precaution .......................................................................................................................... 3
1.2 Warning ......................................................................................................................................... 3
2. Part Names And Functions ......................................................................................................................... 8
2.1 Model Names of Indoor/Outdoor units .......................................................................................... 8
2.2 Functions of Indoor/Outdoor units ................................................................................................ 8
3. Specification ................................................................................................................................................ 9
4. Dimension .................................................................................................................................................. 13
4.1 Indoor Unit................................................................................................................................... 13
4.2 Outdoor Unit ................................................................................................................................ 15
5. Refrigerant Cycle Diagram ....................................................................................................................... 16
6. Wiring Diagram .......................................................................................................................................... 17
6.1 Indoor Unit................................................................................................................................... 17
6.2 Outdoor Unit ................................................................................................................................ 18
7 Installation Details ...................................................................................................................................... 20
7.1 Wrench torque sheet for installation ........................................................................................... 20
7.2 Connecting the cables ................................................................................................................ 20
7.3 Pipe length and the elevation ..................................................................................................... 21
7.4 Installation for the first time ......................................................................................................... 22
7.5 Adding the refrigerant after running the system for many years ................................................ 25
7.6 Re-installation while the indoor unit need to be repaired ........................................................... 26
7.7 Re-installation while the outdoor unit need to be repaired ......................................................... 28
8. Operation Characteristics ......................................................................................................................... 32
9. Electronic function .................................................................................................................................... 33
9.1 Abbreviation ................................................................................................................................ 33
9.2 Display function ........................................................................................................................... 33
9.3 Main Protection ........................................................................................................................... 34
9.4 Operation Modes and Functions................................................................................................. 36
10. Troubleshooting ....................................................................................................................................... 51
10.1 Indoor Unit Error Display........................................................................................................... 51
10.2 Diagnosis and Solution ............................................................................................................. 52
11. Exploded View .......................................................................................................................................... 71
11.1 Indoor unit ................................................................................................................................. 71
11.1 Outdoor unit ............................................................................................................................... 79
PRECAUTION
1. Precaution
1.1 Safety Precaution

To prevent injury to the user or other people and property damage, the following
instructions must be followed.

Incorrect operation due to ignoring instruction will cause harm or damage.

Before service the unit, be sure to read this service manual at first.
1.2 Warning
 Installation

Do not use a defective or underrated circuit breaker. Use this appliance on a dedicated
circuit.
There is risk of fire or electric shock.

For electrical work, contact the dealer, seller, a qualified electrician, or an authorized
service center.
Do not disassemble or repair the product, there is risk of fire or electric shock.

Always ground the product.
There is risk of fire or electric shock.

Install the panel and the cover of control box securely.
There is risk of fire of electric shock.

Always install a dedicated circuit and breaker.
Improper wiring or installation may cause fore or electric shock.

Use the correctly rated breaker of fuse.
There is risk of fire or electric shock.

Do not modify or extend the power cable.
There is risk of fire or electric shock.

Do not install, remove, or reinstall the unit by yourself (customer).
There is risk of fire, electric shock, explosion, or injury.

Be caution when unpacking and installing the product.
Sharp edges could cause injury, be especially careful of the case edges and the fins on the
HKD DCI
3
Version
- 1
PRECAUTION
condenser and evaporator.

For installation, always contact the dealer or an authorized service center.

Do not install the product on a defective installation stand.

Be sure the installation area does not deteriorate with age.
If the base collapses, the air conditioner could fall with it, causing property damage, product failure,
and personal injury.

Do not let the air conditioner run for a long time when the humidity is very high and a
door or a window is left open.

Take care to ensure that power cable could not be pulled out or damaged during
operation.
There is risk of fire or electric shock.

Do not place anything on the power cable.
There is risk of fire or electric shock.

Do not plug or unplug the power supply plug during operation.
There is risk of fire or electric shock.

Do not touch (operation) the product with wet hands.

Do not place a heater or other appliance near the power cable.
There is risk of fire and electric shock.

Do not allow water to run into electrical parts.
It may cause fire, failure of the product, or electric shock.

Do not store or use flammable gas or combustible near the product.
There is risk of fire or failure of product.

Do not use the product in a tightly closed space for a long time.
Oxygen deficiency could occur.

When flammable gas leaks, turn off the gas and open a window for ventilation before
turn the product on.

If strange sounds or smoke comes from product, turn the breaker off or disconnect the
power supply cable.
There is risk of electric shock or fire.

Stop operation and close the window in storm or hurricane. If possible, remove the
HKD DCI
4
Version
- 1
PRECAUTION
product from the window before the hurricane arrives.
There is risk of property damage, failure of product, or electric shock.

Do not open the inlet grill of the product during operation. (Do not touch the electrostatic
filter, if the unit is so equipped.)
There is risk of physical injury, electric shock, or product failure.

When the product is soaked, contact an authorized service center.
There is risk of fire or electric shock.

Be caution that water could not enter the product.
There is risk of fire, electric shock, or product damage.

Ventilate the product from time to time when operating it together with a stove etc.
There is risk of fire or electric shock.

Turn the main power off when cleaning or maintaining the product.
There is risk of electric shock.

When the product is not be used for a long time, disconnect the power supply plug or
turn off the breaker.
There is risk of product damage or failure, or unintended operation.

Take care to ensure that nobody could step on or fall onto the outdoor unit.
This could result in personal injury and product damage.
 CAUTION

Always check for gas (refrigerant) leakage after installation or repair of product.
Low refrigerant levels may cause failure of product.

Install the drain hose to ensure that water is drained away properly.
A bad connection may cause water leakage.

Keep level even when installing the product.
It can avoid vibration of water leakage.

Do not install the product where the noise or hot air from the outdoor unit could damage
the neighborhoods.
It may cause a problem for your neighbors.
HKD DCI
5
Version
- 1
PRECAUTION

Use two or more people to lift and transport the product.

Do not install the product where it will be exposed to sea wind (salt spray) directly.
It may cause corrosion on the product. Corrosion, particularly on the condenser and evaporator fins,
could cause product malfunction or inefficient operation.
 Operational

Do not expose the skin directly to cool air for long time. (Do not sit in the draft).

Do not use the product for special purposes, such as preserving foods, works of art etc.
It is a consumer air conditioner, not a precision refrigerant system.
There is risk of damage or loss of property.

Do not block the inlet or outlet of air flow.

Use a soft cloth to clean. Do not use harsh detergents, solvents, etc.
There is risk of fire, electric shock, or damage to the plastic parts of the product.

Do not touch the metal parts of the product when removing the air filter. They are very
sharp.

Do not step on or put anything on the product. (outdoor units)

Always insert the filter securely. Clean the filter every two weeks or more often if
necessary.
A dirty filter reduces the efficiency of the air conditioner and could cause product malfunction or
damage.

Do not insert hands or other objects through air inlet or outlet while the product is
operated.

Do not drink the water drained from the product.

Use a firm stool or ladder when cleaning or maintaining the product.
Be careful and avoid personal injury.

Replace the all batteries in the remote control with new ones of the same type. Do not
mix old and new batteries or different types of batteries.
There is risk of fire or explosion.

Do not recharge or disassemble the batteries. Do not dispose of batteries in a fire.
They may burn of explode.
HKD DCI
6
Version
- 1
PRECAUTION

If the liquid from the batteries gets onto your skin or clothes, wash it well with clean
water. Do not use the remote of the batteries have leaked.
HKD DCI
7
Version
- 1
SPECIFICATION
2. Part Names And Functions
2.1 Model Names of Indoor/Outdoor units
Series
Inverter
Capacity
Indoor units
Outdoor units
9k
AWSI-HKD009-N11
AWAU-YKD009-H11
12k
AWSI-HKD012-N11
AWAU-YKD012-H11
18k
AWSI-HKD018-N11
AWAU-YKD018-H11
24k
AWSI-HKD024-N11
AWAU-YKD024-H11
2.2 Functions of Indoor/Outdoor units
Filter
2 ways of drainage
Killer Of Formaldehyde
Louver Position Memory Function
Ionizer(O)
Refrigerant Leakage Detect
Silver Ico Filter(O)
Self-diag. Function
Vitamin C Filter(O)
Hydrophilic Aluminum Fin
3M HAM Filter(O)
Anti-rust Cabinet
Bio Filter(O)
Valve Protection Cover
Golden Fin(O)
PTC Heating Belt(O)
1W Standby
Compressor Crankcase Heater(O)
O: optional function
HKD DCI
8
Version
- 1
SPECIFICATION
3. Specification
Model Indoor Unit
Model Outdoor Unit
Installation Method of Pipe
Units
Capacity (1)
Pdesign
SEER /SCOP (2)
Energy efficiency class
Annual energy consumption
Tbiv
Tol
Power supply
Circuit breaker rating
Fan type & quantity
Fan speeds
H/M/L
Air flow (3)
H/M/L
External static pressure
Min-Max
Sound power level (4)
H/M/L
Sound pressure level(5)
H/M/L
Moisture removal
Condensate drain tube I.D
Dimensions
WxHxD
Weight
Package dimensions
LxWxH
Packaged weight
Stacking height
Refrigerant control
Compressor type, model
Fan type & quantity
Fan speeds
H/L
Air flow
H/L
Sound power level(4)
H/L
Sound pressure level(5)
H/L
Dimensions
WxHxD
Weight
Package dimensions
LxWxH
Packaged weight
Stacking height
Refrigerant type
Refrigerant charge (standard connecting tubing length)
Additional charge per 1 meter
Liquid line
Connections between units Suction line
Max.tubing length
Max.height difference
Operation control type
Heating elements
Others
kW
kW
W/W
OUTDOOR
INDOOR
Characteristics
HKD DCI
9
kWh
oC
oC
V/Ph/Hz
A
RPM
m3/hr
Pa
dB(A)
dB(A)
l/hr
mm
mm
kg
mm
kg
units
RPM
m3/hr
dB(A)
dB(A)
mm
kg
mm
kg
Units
kg(5m)
gr / 1m
In.(mm)
In.(mm)
m.
m.
AWSI-HKD009-N11
AWAU-YKD009-H11
Flared
Heating
Cooling
Average
2.70(1.0~3.2)
2.8(1.0~3.4)
2.7
2.4
5.8
3.8
A+
A
163
884
N/A
-7
N/A
-15
220-240V/Single/50Hz
10
Cross flow fan x1
1150/1000 /800
1150/1000/ 800
620/540/440
620/540/440
0
58
42/38/30
1.0
16
800 x275x188
6.5
865 x350x265
9.5
8
Capillary tube
Rotary DC Inverter
Axial x 1
800
1800
64
52
780 x540x250
27.5
910x335x585
30
5
R410A
0.8
15
1/4" (6.35)
3/8"(9.52)
20
8
Remote control
kW
Version
- 1
SPECIFICATION
Model Indoor Unit
Model Outdoor Unit
AWSI-HKD012-N11
AWAU-YKD012-H11
Installation Method of Pipe
Flared
Characteristics
Capacity (1)
Pdesign
SEER /SCOP
(2)
Cooling
kW
3.2(1.2~3.8)
3.5(1.2~4.0)
kW
3.2
3.05
W/W
5.8
3.8
A+
A
Energy efficiency class
Annual energy consumption
Heating
Units
Average
kWh
193
1124
Tbiv
oC
N/A
-7
Tol
oC
N/A
-15
Power supply
V/Ph/Hz
Circuit breaker rating
A
Fan type & quantity
H/M/L
RPM
1200 /1050 /800
1200/1050 /800
Air flow (3)
H/M/L
m3/hr
630/550/430
630/550/430
Min-Max
Pa
H/M/L
dB(A)
58
H/M/L
dB(A)
43/39/31
Moisture removal
l/hr
1.1
Condensate drain tube I.D
mm
16
mm
800 x275x188
kg
7.5
mm
865 x350x265
kg
9.5
units
8
Sound power level
INDOOR
10
Cross flow fan x1
Fan speeds
External static pressure
(4)
Sound pressure level(5)
Dimensions
WxHxD
Weight
Package dimensions
LxWxH
Packaged weight
Stacking height
Refrigerant control
0
Capillary tube
Compressor type, model
Rotary DC Inverter
Fan type & quantity
Axial x 1
Fan speeds
H/L
RPM
800
Air flow
H/L
m3/hr
1800
Sound power level(4)
H/L
dB(A)
64
Sound pressure
OUTDOOR
220-240V/Single/50Hz
level(5)
Dimensions
H/L
dB(A)
53
WxHxD
mm
780 x540x250
kg
27.5
LxWxH
mm
910x335x585
kg
29.5
Weight
Package dimensions
Packaged weight
Stacking height
Units
Refrigerant type
5
R410A
Refrigerant charge (standard connecting tubing length)
kg(5m)
0.95
Additional charge per 1 meter
gr / 1m
15
Liquid line
In.(mm)
1/4"(6.35)
Suction line
In.(mm)
3/8"(9.52)
Max.tubing length
m.
20
Max.height difference
m.
8
Connections between units
Operation control type
Remote control
Heating elements
kW
Others
HKD DCI
10
Version
- 1
SPECIFICATION
Model Indoor Unit
Model Outdoor Unit
AWSI-HKD018-N11
AWAU-YKD018-H11
Installation Method of Pipe
Flared
Characteristics
Capacity (1)
Pdesign
SEER /SCOP
(2)
Cooling
kW
5.0(1.4~6.2)
5.1(1.4~6.4)
kW
5
4.8
W/W
Energy efficiency class
Annual energy consumption
Heating
Units
Average
6.5
3.8
A++
A
kWh
269
1768
Tbiv
oC
N/A
-6
Tol
oC
N/A
-15
Power supply
V/Ph/Hz
Circuit breaker rating
A
Fan type & quantity
H/M/L
RPM
1100 / 800 / 700
1150 / 800 / 700
Air flow (3)
H/M/L
m3/hr
730/480/400
760/480/400
Min-Max
Pa
H/M/L
dB(A)
58
H/M/L
dB(A)
43/40/33
Moisture removal
l/hr
1.7
Condensate drain tube I.D
mm
16
mm
940 x275x205
kg
9.5
mm
1015 x350x265
kg
12.5
units
8
Sound power level
INDOOR
16
Cross flow fan x1
Fan speeds
External static pressure
(4)
Sound pressure level(5)
Dimensions
WxHxD
Weight
Package dimensions
LxWxH
Packaged weight
Stacking height
Refrigerant control
0
Capillary tube
Compressor type, model
Rotary DC Inverter
Fan type & quantity
Axial x 1
Fan speeds
H/L
RPM
800
Air flow
H/L
m3/hr
2200
Sound power level(4)
H/L
dB(A)
65
Sound pressure
OUTDOOR
220-240V/Single/50Hz
level(5)
Dimensions
H/L
dB(A)
55
WxHxD
mm
760 x590x285
kg
35
LxWxH
mm
887x355x645
kg
37.5
Weight
Package dimensions
Packaged weight
Stacking height
units
Refrigerant type
4
R410A
Refrigerant charge (standard connecting tubing length)
kg(5m)
1.25
Additional charge per 1 meter
gr / 1m
15
Liquid line
In.(mm)
1/4"(6.35)
Suction line
In.(mm)
1/2"(12.7)
Max.tubing length
m.
20
Max.height difference
m.
8
Connections between units
Operation control type
Remote control
Heating elements
kW
Others
HKD DCI
11
Version
- 1
SPECIFICATION
Model Indoor Unit
Model Outdoor Unit
AWSI-HKD024-N11
AWAU-YKD024-H11
Installation Method of Pipe
Flared
Characteristics
Capacity (1)
Pdesign
SEER /SCOP (2)
Heating
Units
Cooling
kW
6.25(2.5~7.2)
7.0(2.5~7.5)
kW
6.25
6.3
W/W
6.2
3.8
Energy efficiency class
Average
A++
A
kWh
353
2321
Tbiv
oC
N/A
-6
Tol
oC
N/A
-15
Annual energy consumption
Power supply
V/Ph/Hz
Circuit breaker rating
A
Fan type & quantity
INDOOR
25
Cross flow fan x1
Fan speeds
H/M/L
RPM
1180/1100/ 900
1180/1100 / 900
Air flow (3)
H/M/L
m3/hr
1150/1050/900
1150/1050/900
External static pressure
Min-Max
Pa
0
Sound power level (4)
H/M/L
dB(A)
64
Sound pressure level(5)
H/M/L
dB(A)
50/47/41
Moisture removal
l/hr
2.4
Condensate drain tube I.D
mm
16
mm
1045 x315x235
kg
12.2
mm
1135 x315x395
kg
15.3
Dimensions
WxHxD
Weight
Package dimensions
LxWxH
Packaged weight
Stacking height
units
Refrigerant control
8
Capillary tube
Compressor type, model
Twin-rotary DC Inverter
Fan type & quantity
Axial x 1
Fan speeds
H/L
RPM
850
Air flow
H/L
m3/hr
2700
Sound power level(4)
H/L
dB(A)
69
Sound pressure
OUTDOOR
220-240V/Single/50Hz
level(5)
Dimensions
H/L
dB(A)
58
WxHxD
mm
845 x700x320
kg
46.7
LxWxH
mm
965x395x755
kg
50
units
3
Weight
Package dimensions
Packaged weight
Stacking height
Refrigerant type
R410A
Refrigerant charge (standard connecting tubing length)
kg(5m)
1.95
Additional charge per 1 meter
gr / 1m
30
Liquid line
In.(mm)
3/8"(9.52)
Suction line
In.(mm)
5/8"(15.9)
Max.tubing length
m.
25
Max.height difference
m.
10
Connections between units
Operation control type
Remote control
Heating elements
kW
Others
HKD DCI
12
Version
- 1
DIMENSION
4. Dimension
4.1 Indoor Unit
H
D
W
HKD DCI
Model
W
D
H
AWSI-HKD009-N11
800
188
275
AWSI-HKD012-N11
800
188
275
AWSI-HKD018-N11
940
205
275
AWSI-HKD024-N11
1045
235
315
13
Version
- 1
DIMENSION
Model
L(mm)
R(mm)
H(mm)
100
95
45
110
100
45
AWSI-HKD009-N11
AWSI-HKD012-N11
AWSI-HKD018-N11
Dimension of installation
hole(mm)
¢65
R
L
H
Model
L(mm)
R(mm)
H(mm)
Dimension of installation hole(mm)
AWSI-HKD024-N11
293
163
45
¢65
HKD DCI
14
Version
- 1
DIMENSION
4.2 Outdoor Unit
More than 30cm
More than 60cm
(Service space)
More than 30cm
Fe
n
ob ce o
sta
r
cle
s
More than 60cm
More than 200cm
Model
W
D
H
W1
A
B
AWAU-YKD009-H11
780
250
540
843
549
276
AWAU-YKD012-H11
780
250
540
843
549
276
AWAU-YKD018-H11
760
285
590
823
530
290
AWAU-YKD024-H11
845
320
700
908
560
335
HKD DCI
15
Version
- 1
REFRIGERANT CYCLE DIAGRAM
5. Refrigerant Cycle Diagram
INDOOR
OUTDOOR
LIQUID SIDE
CHECK VALVE
(Heating Model only)
2-WAY VALVE
T3 Condenser
temp. sensor
CAPILIARY TUBE
HEAT
EXCHANGE
(EVAPORATOR)
HEAT
EXCHANGE
(CONDENSER)
T4 Ambient
temp. sensor
T1 Room temp.
sensor
T2 Evaporator
temp. sensor
GAS SIDE
4-WAY VALVE
3-WAY VALVE
Accumulator
Compressor
T5 Discharge temp. sensor
COOLING
HEATING
HKD DCI
16
Version
- 1
WIRING DIAGRAM
6. Wiring Diagram
6.1 Indoor Unit
AWSI-HKD009-N11, AWSI-HKD012-N11, AWSI-HKD018-N11
AWSI-HKD024-N11
HKD DCI
17
Version
- 1
WIRING DIAGRAM
6.2 Outdoor Unit
AWAU-YKD009-H11
AWAU-YKD012-H11, AWAU-YKD018-H11
HKD DCI
18
Version
- 1
WIRING DIAGRAM
AWAU-YKD024-H11
HKD DCI
19
Version
- 1
INSTALLATION DETAILS
7 Installation Details
7.1 Wrench torque sheet for installation
Outside diameter
Torque
Additional tightening torque
mm
inch
N.cm
N.cm
Ф6.35
1/4
1500(153kgf.cm)
1600(163kgf.cm)
Ф9.52
3/8
2500(255kgf.cm)
2600(265kgf.cm)
Ф12.7
1/2
3500(357kgf.cm)
3600(367kgf.cm)
Ф15.9
5/8
4500(459kgf.cm)
4700(479kgf.cm)
Ф19
3/4
6500(663kgf.cm)
6700(683kgf.cm)
7.2 Connecting the cables
The power cord of connect should be selected according to the following specifications sheet.
Rated current of appliance
Nominal cross-sectional area (mm²)
>3 and ≤6
0.75
>6 and ≤10
1
>10 and ≤16
1.5
>16 and ≤25
2.5
The cable size and the current of the fuse or switch are determined by the maximum current indicated
on the nameplate which located on the side panel of the unit. Please refer to the nameplate before
selecting the cable, fuse and switch.
HKD DCI
20
Version
- 1
INSTALLATION DETAILS
7.3 Pipe length and the elevation
The pipe length and refrigerant amount:
Pipe size
Model
Standard
length
(m)
Max.
Elevation
B (m)
Max.
Length
A (m)
Additional
refrigerant
(g/m)
5
8
20
20
5
8
20
20
Gas
Liquid
3/8’’
(Ф9.52)
1/4’’
(Ф6.35)
AWSI-HKD018-N11+AWAU-YKD018-H11
1/2’’
(Ф12.7)
1/4’’
(Ф6.35)
5
8
20
20
AWSI-HKD024-N11+AWAU-YKD024-H11
3/5’’
(Ф15.9)
3/8’’
(Ф9.52)
5
10
25
40
AWSI-HKD009-N11+AWAU-YKD009-H11
AWSI-HKD012-N11+AWAU-YKD012-H11
Caution:
The capacity test is based on the standard length and the maximum permissive length is basedon the
system reliability.
Oil trap:
When the outdoor unit is installed above the indoor unit an oil trap is required every 3m along the
suction line at the lowest point. In case the indoor unit is installed above the outdoor, no trap is
required.
HKD DCI
21
Version
- 1
INSTALLATION DETAILS
7.4 Installation for the first time
Air and moisture in the refrigerant system have undesirable effects as below:
●
●
●
●
●
Pressure in the system rises.
Operating current rises.
Cooling or heating efficiency drops.
Moisture in the refrigerant circuit may freeze and block capillary tubing.
Water may lead to corrosion of parts in the refrigerant system.
Therefore, the indoor units and the pipes between indoor and outdoor units must be leak tested
and evacuated to remove gas and moisture from the system.
Gas leak check (Soap water method):
Apply soap water or a liquid neutral detergent on the indoor unit connections or outdoor unit
connections by a soft brush to check for leakage of the connecting points of the piping. If bubbles
come out, the pipes have leakage.
1. Air purging with vacuum pump
(Indoor unit)
(Outdoor unit)
(Liquid side)
Two-way valve
Close
(Gas side)
Three-way valve
Manifold valve
Compound meter
Pressure
gauge
-0.1MPa
Lo
Handle Lo
Charge hose
Close
Hi
Handle Hi
Charge hose
Vacuum
pump
Vacuum
pump
1) Completely tighten the flare nuts of the indoor and outdoor units, confirm that both the 2-way and
3-way valves are set to the closed position.
2) Connect the charge hose with the push pin of handle lo to the 3-way valves gas service port..
3) Connect the charge hose of handle hi connection to the vacuum pump.
4) Fully open the handle Lo of the manifold valve.
5) Operate the vacuum pump to evacuate.
6) Make evacuation for 30 minutes and check whether the compound meter indicates -0.1Mpa. If
HKD DCI
22
Version - 1
INSTALLATION DETAILS
the meter does not indicate -0.1Mpa after pumping 30 minutes, it should be pumped 20 minutes more. If
the pressure can’t achieve -0.1Mpa after pumping 50 minutes, please check if there are some leakage
points.
Fully close the handle Lo valve of the manifold valve and stop the operation of the vacuum pump.
Confirm that the gauge needle does not move (approximately 5 minutes after turning off the vacuum
pump).
7) Turn the flare nut of the 3-way valves about 45°counterclockwise for 6 or 7seconds after the gas
coming out, then tighten the flare nut again. Make sure the pressure display in the pressure indicator is
a little higher than the atmosphere pressure. Then remove the charge hose from the 3 way valve.
8) Fully open the 2 way valve and 3 way valve and securely tighten the cap of the 3 way valve.
2. Air purging by refrigerant
Procedure:
1). Confirm that both the 2-way and 3-way valves are set to the closed position.
2). Connect the charge set and a charging cylinder to the service port of the 3-way valve.
3). Air purging.
Open the valves on the charging cylinder and the charge set. Purge the air by loosening the flare nut on
the 2-way valve approximately 45’ for 3 seconds then closing it for 1 minute; repeat 3 times.
After purging the air, use a torque wrench to tighten the flare nut on the 2-way valve.
4). Check the gas leakage.
HKD DCI
23
Version
- 1
INSTALLATION DETAILS
Check the flare connections for gas leakage.
5). Discharge the refrigerant.
Close the valve on the charging cylinder and discharge the refrigerant by loosening the flare nut on the
2-way valve approximately 45’ until the gauge indicates 0.3 to 0.5 Mpa.
6). Disconnect the charge set and the charging cylinder, and set the 2-way and 3-way valves to the open
position.
Be sure to use a hexagonal wrench to operate the valve stems.
7). Mount the valve stems nuts and the service port cap.
Be sure to use a torque wrench to tighten the service port cap to a torque 18N·m.
Be sure to check the gas leakage.
3. Adding the refrigerant if the pipe length >5m
Electronic scale
Procedure:
1). Connect the charge hose to the charging cylinder, open the 2-way valve and the 3-way valve.
Connect the charge hose which you disconnected from the vacuum pump to the valve at the bottom of
the cylinder. If the refrigerant is R410A, make the cylinder bottom up to ensure the liquid charge.
2). Purge the air from the charge hose.
Open the valve at the bottom of the cylinder and press the check valve on the charge set to purge the
air (be careful of the liquid refrigerant).
HKD DCI
24
Version
- 1
INSTALLATION DETAILS
3) Put the charging cylinder onto the electronic scale and record the weight.
4) Operate the air conditioner at the cooling mode.
5) Open the valves (Low side) on the charge set and charge the system with liquid refrigerant.
6).When the electronic scale displays the proper weight (refer to the table), disconnect the charge hose
from the 3-way valve’s service port immediately and turn off the air conditioner before disconnecting the
hose.
7). Mount the valve stem caps and the service port
Use torque wrench to tighten the service port cap to a torque of 18N.m.
Be sure to check for gas leakage.
7.5 Adding the refrigerant after running the system for many years
Electronic scale
Procedure:
1). Connect the charge hose to the 3-way service port, open the 2-way valve and the 3-way valve.
Connect the charge hose to the valve at the bottom of the cylinder. If the refrigerant is R410A, make
the cylinder bottom up to ensure liquid charge.
2). Purge the air from the charge hose.
Open the valve at the bottom of the cylinder and press the check valve on the charge set to purge the
HKD DCI
25
Version
- 1
INSTALLATION DETAILS
air (be careful of the liquid refrigerant).
3) Put the charging cylinder onto the electronic scale and record the weight.
4) Operate the air conditioner at the cooling mode.
5) Open the valves (Low side) on the charge set and charge the system with liquid refrigerant.
6).When the electronic scale displays the proper weight (refer to the gauge and the pressure of the low
side), disconnect the charge hose from the 3-way valve’s service port immediately and turn off the air
conditioner before disconnecting the hose.
7). Mount the valve stem caps and the service port
Use torque wrench to tighten the service port cap to a torque of 18N.m.
Be sure to check for gas leakage.
7.6 Re-installation while the indoor unit need to be repaired
1. Collecting the refrigerant into the outdoor unit
Procedure
1). Confirm that both the 2-way and 3-way valves are set to the opened position
Remove the valve stem caps and confirm that the valve stems are in the opened position.
Be sure to use a hexagonal wrench to operate the valve stems.
2). Connect the charge hose with the push pin of handle lo to the 3-way valves gas service port.
HKD DCI
26
Version
- 1
INSTALLATION DETAILS
3). Air purging of the charge hose.
Open the handle Lo valve of the manifold valve slightly to purge air from the charge hose for 5 seconds
and then close it quickly.
4). Set the 2-way valve to the close position.
5). Operate the air conditioner at the cooling cycle and stop it when the gauge indicates 0.1MPa.
6). Set the 3-way valve to the closed position immediately
Do this quickly so that the gauge ends up indicating 0.3 to 0.5Mpa.
Disconnect the charge set, and tighten the 2-way and 3-way valve’s stem nuts.
Use a torque wrench to tighten the 3-way valves service port cap to a torque of 18N.m.
Be sure to check for gas leakage.
2. Air purging by the refrigerant
Procedure:
1). Confirm that both the 2-way and 3-way valves are set to the closed position.
2). Connect the charge set and a charging cylinder to the service port of the 3-way valve
Leave the valve on the charging cylinder closed.
3). Air purging.
HKD DCI
27
Version
- 1
INSTALLATION DETAILS
Open the valves on the charging cylinder and the charge set. Purge the air by loosening the flare nut on
the 2-way valve approximately 45’ for 3 seconds then closing it for 1 minute; repeat 3 times.
After purging the air, use a torque wrench to tighten the flare nut on the 2-way valve.
4). Check the gas leakage
Check the flare connections for gas leakage.
5). Discharge the refrigerant.
Close the valve on the charging cylinder and discharge the refrigerant by loosening the flare nut on the
2-way valve approximately 45’ until the gauge indicates 0.3 to 0.5 Mpa.
6). Disconnect the charge set and the charging cylinder, and set the 2-way and 3-way valves to the open
position
Be sure to use a hexagonal wrench to operate the valve stems.
7). Mount the valve stems nuts and the service port cap
Be sure to use a torque wrench to tighten the service port cap to a torque 18N.m.
Be sure to check the gas leakage.
7.7 Re-installation while the outdoor unit need to be repaired
1. Evacuation for the whole system
Procedure:
HKD DCI
28
Version
- 1
INSTALLATION DETAILS
1). Confirm that both the 2-way and 3-way valves are set to the opened position.
2). Connect the vacuum pump to 3-way valve’s service port.
3). Evacuation for approximately one hour. Confirm that the compound meter indicates -0.1Mpa.
4). Close the valve (Low side) on the charge set, turn off the vacuum pump, and confirm that the gauge
needle does not move (approximately 5 minutes after turning off the vacuum pump).
5). Disconnect the charge hose from the vacuum pump.
HKD DCI
29
Version
- 1
INSTALLATION DETAILS
2. Refrigerant charging
Electronic scale
Procedure:
1). Connect the charge hose to the charging cylinder, open the 2-way valve and the 3-way valve
Connect the charge hose which you disconnected from the vacuum pump to the valve at the bottom of
the cylinder. If the refrigerant is R410A, make the cylinder bottom up to ensure liquid charge.
2). Purge the air from the charge hose
Open the valve at the bottom of the cylinder and press the check valve on the charge set to purge the
air (be careful of the liquid refrigerant).
3) Put the charging cylinder onto the electronic scale and record the weight.
4). Open the valves (Low side) on the charge set and charge the system with liquid refrigerant
If the system cannot be charge with the specified amount of refrigerant, or can be charged with a little at
a time (approximately 150g each time) , operating the air conditioner in the cooling cycle; however, one
time is not sufficient, wait approximately 1 minute and then repeat the procedure.
5).When the electronic scale displays the proper weight, disconnect the charge hose from the 3-way
valve’s service port immediately
If the system has been charged with liquid refrigerant while operating the air conditioner, turn off the air
conditioner before disconnecting the hose.
6). Mounted the valve stem caps and the service port
HKD DCI
30
Version
- 1
INSTALLATION DETAILS
Use torque wrench to tighten the service port cap to a torque of 18N.m.
Be sure to check for gas leakage
HKD DCI
31
Version
- 1
OPERATING CHARACTERISTICS
8. Operation Characteristics
Temperature
Cooling operation
Heating operation
Drying operation
Mode
Room temperature
Outdoor temperature
≥17℃
≤30℃
>10℃
-15℃~50℃
-15℃~30℃
-15℃~50℃
CAUTION:
1. If the air conditioner is used beyond the above conditions, certain safety protection features
may come into operation and cause the unit to operate abnormally.
2. The room relative humidity should be less than 80%. If the air conditioner operates beyond this
figure, the surface of the air conditioner may attract condensation. Please set the vertical air flow
louver to its maximum angle (vertically to the floor), and set HIGH fan mode.
3. The optimum performance will be achieved during this operating temperature zone.
HKD DCI
32
Version
- 1
ELECTRONIC FUNCTION
9. Electronic function
9.1 Abbreviation
T1: Indoor room temperature(RAT)
T2: Coil temperature of evaporator (ICT)
T3: Coil temperature of condenser (OCT)
T4: Outdoor ambient temperature(OAT)
T5: Compressor discharge temperature(CTT)
9.2 Display function
9.2.1 Icon explanation on indoor display board.
1. In normal situation, the setting temperature is displayed.
(display room temp. in fan mode.)
2* 7 segments display
2. Shows “SC” when self clean function is activated, ”FP” when 8ºC
heating function is activated.
3. Shows the alarm code whenever there is an alarm.
ION INDICATOR
Lights up when ionizer or plasma function is activated.
(optional)
DEFROSTING
Lights up when the unit is under defrosting operation or when the anti-cold
INDICATOR
air function is activated.
RUN INDICATOR
Lights up when the unit is in operation.
TIMER INDICATOR
Lights up when TIMER function is activated.
HKD DCI
33
Version
- 1
ELECTRONIC FUNCTION
9.3 Main Protection
9.3.1 Time delay at restart for compressor
1 minute delay for the 1st time start-up and 3 minutes delay for others.
9.3.2 Temperature protection of compressor top
The unit will stop working when the compressor top temp. protector cut off, and will restart after the
compressor top temp. protector restart.
9.3.3 Temperature protection of compressor discharge
When the compressor discharge temp. is getting higher, the running frequency will be limited as below
rules:
---Compressor discharge temp. T5>115℃ for 5s, compressor stops and restarts up till T5<90℃
---110<T5<115℃, decrease the frequency to the lower level every 2 minutes.
---105<T5<110℃, keep running at the current frequency.
----T5<105℃, no limit for frequency.
9.3.4 Fan Speed is out of control
When Indoor Fan Speed keeps too low (300RPM) for certain time, the unit will stop and the LED will
display the failure
9.3.5 Inverter module protection
The Inverter module has a protection function about current, voltage and temperature. If these
protections happen, the corresponding code will display on indoor unit and the unit will stop working.
9.3.6 Indoor fan delayed open function
When the unit starts up, the louver will be active immediately and the indoor fan will open 10s later.
If the unit runs in heating mode, the indoor fan will be also controlled by anti-cold wind function.
9.3.7 Compressor preheating functions
Preheating permitting condition:
If T4(outdoor ambient temperature)<3℃ and the machine connects to power supply newly or if T4<
3℃ and compressor has stopped for over 3 hours, the compressor heating cable will work.
Preheating mode:
A weak current flow through the coil of compressor from the wiring terminal of the compressor, then the
compressor is heated without operation.
Preheating release condition:
HKD DCI
34
Version
- 1
ELECTRONIC FUNCTION
If T4>5℃ or the compressor starts running, the preheating function will stop.
9.3.8 Sensor protection at open circuit and breaking disconnection.
When there’s one temperature sensor in malfunction, the air conditioner will display error code and will
not stop immediately, to avoid the case that the air conditioner is in urgent need.
Fault temp.
sensor
Operation in cooling,
drying and fan only mode
Operation in heating mode
T1
Run supposed T1=26℃
high fan speed
Run supposed T1=26℃ medium fan speed
T2
Normal
During the first 1 minute of compressor operation, indoor
fan shuts off. After that, indoor fan runs at medium fan
speed for 1 minute and then resume to the setting fan
speed.
T3
Run with compressor
frequency≤F14
3 minutes’ defrosting every 40 minutes when T4<7℃; 2
minutes’ defrosting every 90 minutes when T4≥7℃.
T4
Run supposed T4=50℃
Run supposed T4=15℃
TP
Run supposed T4=50℃
Run supposed T4=15℃
9.3.9 Refrigerant leakage detection
This function is only active in cooling mode. It can better prevent the compressor being damaged
by refrigerant leakage or compressor overload.
Open condition:
Define the evaporator coil temp.T2 of the compressor just starts running as Tcool.
In the beginning 5 minutes after the compressor starts up, if T2 <Tcool-2℃ does not keep
continuous 4 seconds and this situation happens 3 times, the display area will show “EC” and AC will
turn off.
9.3.10 Zero crossing detection error protection(only for AWSI-HKD009-N11)
If AC detects time interval is not correct for continuous 240s, the unit will stop and the LED will display
the failure. The correct zero crossing signal time interval should be between 6-13ms.
HKD DCI
35
Version
- 1
ELECTRONIC FUNCTION
9.4 Operation Modes and Functions
9.4.1 Fan mode
(1) Outdoor fan and compressor stop.
(2) Temperature setting function is disabled, and no setting temperature is displayed.
(3) Indoor fan can be set to high/med/low/auto.
(4) The louver operates same as in cooling mode.
(5) Auto fan:
T1-24
6.0
5.0
4.0
2.5
1.0
HKD DCI
H
a
b
c
d
e
36
(H-L)*0.75+L
(H-L)*0.5+L
(H-L)*0.25+L
L
Version
- 1
ELECTRONIC FUNCTION
9.4.2 Cooling Mode
9.4.2.1 Compressor running rules
The maximum operation frequency of compressor after starting submits to following rule.
T4
50
Fmax=T4FREMAX1
49
Fmax=T4FREMAX2
45
44
Fmax=T4FREMAX3
41
40
Fmax=T4FREMAX4
33
32
Fmax=T4FREMAX5
30
29
Fmax=T4FREMAX6
22
20
Fmax=T4FREMAX7
Meanwhile, the maximum frequency is limited by the indoor fan speed.
Indoor fan speed
Maximum frequency
High speed / turbo function
No limit
Silent mode
Fixed at F3
If users switch on AC by remote controller, the compressor will run at the Fmax frequency for 7
minutes according to the outdoor ambient temp. During the 7 minutes, the frequency limitation is active.
7 minutes later, the compressor running frequency will be controlled as below:
HKD DCI
37
Version
- 1
ELECTRONIC FUNCTION
T1-Ts
3.5
A
3.0
2.5
B
C
2.0
D
1.5
E
1.0
F
0.5
G
0.0
H
-1.0
I
-1.5
J
While the zones of A,B,C... are corresponding to different compressor running frequency.
Note:
When T1-Ts keeps in the same temp. zone for 3 minutes, the compressor will run as the below rules:
A:Increase the frequency to 3 grade higher until to FREMAX.
B~E: Increase the frequency to 2 grade higher until to FREMAX.
F~G: Increase the frequency to 1 grade higher until to FREMAX.
H: Keep the current frequency.
:
I: Decrease the frequency to 1 grade lower until to F1.
J: Run at F1 for 1h.(if T1-Ts<-2℃, the compressor will stop)
Meanwhile, the compressor running frequency is limited by the current.
T4
CoolT4Zone5I
50
49
45
CoolT4Zone4I
44
41
CoolT4Zone3I
40
33
CoolT4Zone2I
32
CoolT4Zone1I
HKD DCI
38
Version
- 1
ELECTRONIC FUNCTION
9.4.2.2 Outdoor fan running rules
Cooling
Heating
21
A
A
28
19
18
B
26
25
16
15
23
22
C
C
D
D
20
19
17
E
13
12
10
B
E
While A,B,C…means different fan speed of outdoor unit.
9.4.2.3 Indoor fan running rules
In cooling mode, indoor fan runs all the time and the speed can be selected as high, medium, low, auto
and silent. When the compressor is running, the indoor fan is controlled as below:
HKD DCI
39
Version
- 1
ELECTRONIC FUNCTION
The auto fan acts as below rules:
T1-Ts
6.0
5.0
H
a
4.0
2.5
1.0
b
c
d
e
(H-L)*0.75+L
(H-L)*0.5+L
(H-L)*0.25+L
L
9.4.2.4 Condenser temperature protection
---55℃<T3<60℃, the compressor frequency will decrease to the lower level until to F1 and then runs
at F1.If T3<54℃, the compressor will keep running at the current frequency.
---T3<52℃, the compressor will not limit the frequency and resume to the former frequency.
---T3>60℃ for 5 seconds, the compressor will stop until T3<52℃.
9.4.2.5 Evaporator temperature protection
---T2<0℃, the compressor will stop and restart when T2>=5℃.
---0℃≦T2<4℃, the compressor frequency will be limited and decreased to the lower level
---4℃≤T2≤7℃, the compressor will keep the current frequency.
---T2>7℃, the compressor frequency will not be limited.
HKD DCI
40
Version
- 1
ELECTRONIC FUNCTION
9.4.3 Heating Mode
9.4.3.1 Compressor running rules
The maximum operation frequency of the compressor after starting submits to the following rule.
T4
Off
34
33
28
27
Fmax=T4FREHEATMAX1
25
24
Fmax=T4FREHEATMAX2
22
21
Fmax=T4FREHEATMAX3
19
18
Fmax=T4FREHEATMAX4
17
16
Fmax=T4FREHEATMAX5
15
14
Fmax=T4FREHEATMAX6
12
11
Fmax=T4FREHEATMAX7
6
5
Fmax=T4FREHEATMAX8
1
0
Fmax=T4FREHEATMAX9
Fmax=F21
-3
-4
Fmax=F22
-7
-8
Fmax=F23
-11
-12
Fmax=F24
-15
-16
Fmax=F25
HKD DCI
41
Version
- 1
ELECTRONIC FUNCTION
Meanwhile, the maximum frequency is limited by the indoor fan speed.
Indoor fan speed
Maximum frequency
High speed/8 degree heating/ turbo function
No limit
Medium speed
FHeatMaxMidFan
Low speed/sleep mode
FHeatMaxLowFan
Silent mode
Fixed at F3
If users switch on AC by remote controller, the compressor will run at the Fmax frequency for 7
minutes according to outdoor ambient temp. During the 7 minutes, the frequency limitation is active.
7 minutes later, the compressor running frequency will be controlled as below:
T1-Ts+ΔT
+5.0
J
+4.5
I
+4.0
H
+3.5
G
+3.0
F
+2.5
E
+2.0
D
C
+1.5
B
+1.0
+0.5
A
While the zones of A,B,C... are corresponding to different compressor running frequency.
ΔT=0℃ as default.
Note:
When T1-Ts keeps in the same temp. zone for 3 minutes, the compressor will run as the below rules:
A: Increase the frequency to 3 grade higher until to FREMAX.
B~E: Increase the frequency to 2 grade higher until to FREMAX.
F~G: Increase the frequency to 1 grade higher until to FREMAX.
H: Keep the current frequency.
I: Decrease the frequency to the 1 grade lower until to F1.
HKD DCI
42
Version
- 1
ELECTRONIC FUNCTION
J: Run at F1 for 1h.(if T1-Ts-ΔT >6℃, the compressor will stop)
Meanwhile, the compressor running frequency is limited by the current.
T4
HeatT4Zone4I
15
14
HeatT4Zone3I
10
9.0
HeatT4Zone2I
6.0
5.0
HeatT4Zone1I
9.4.3.2 Outdoor fan running rules
Heating
21
E
19
18
D
16
15
C
13
12
B
10
A
9.4.3.3 Indoor fan running rules
In heating mode, indoor fan can be selected as high, medium, low, auto and silent. The anti-cold- wind
function is preferential. The running rules of anti-cold-wind function depend on both T1 and T2 that is
more comfortable control.
When the compressor is running, the indoor fan is controlled as below:
HKD DCI
43
Version
- 1
ELECTRONIC FUNCTION
If the compressor stops caused by the room temperature rising, the indoor fan will be forced to run 127
seconds with breeze. During this period, the anti-cold-wind is disabled.
Auto fan action in heating mode:
T1-Ts+ΔT
0.0
-1.0
L
(H+-L)*0.2+L
(H+-L)*0.4+L
-2.0
-3.0
(H+-L)*0.6+L
-4.0
(H+-L)*0.6+L
-5.0
-6.0
-6.5
(H+-L)*0.8+L
H+
HKD DCI
44
Version
- 1
ELECTRONIC FUNCTION
9.4.3.4 Defrosting mode
Condition of defrosting:
If any one of the following items is satisfied, AC will enter the defrosting mode.
After the compressor starts up and keeps running, mark the minimum value of T3 from the 10th
minutes to 15th minutes as T30.
1)If the compressor cumulate running time is up to 29 minutes and T3< TCDI1, T3 +
T30SUBT3ONE≦T30.
2)If the compressor cumulate running time is up to 35 minutes and T3< TCDI2, T3 +
T30SUBT3TWO≦T30.
3)If the compressor cumulate running time is up to 29 minutes and T3< TCDI3 for 3 minutes.
4)If the compressor cumulate running time is up to 120 minutes and T3<-15℃.
Condition of ending defrosting:
If any one of the following items is satisfied, the defrosting will finish and the machine will turn to
normal heating mode.
----T3 rises to be higher than TCDE1℃.
----T3 keeps to be higher than TCDE2℃ for 80 seconds.
----The machine has run for 10 minutes in defrosting mode.
HKD DCI
45
Version
- 1
ELECTRONIC FUNCTION
Defrosting action:
For 9k,12k models:
on
Compressor
4-way valve
Outdoor fan
off
on
off
on
off
xx
10s
10s
no longer than 10m
30s
xx=20.
For 18k,24k models:
on
Compressor
4-way valve
Outdoor fan
off
on
off
on
off
xx
10s
10s
no longer than 10m
30s
xx=20
HKD DCI
46
Version
- 1
ELECTRONIC FUNCTION
9.4.3.5 Evaporator coil temperature protection
T2
Off
TEstop
Decrease
TEdown
Hold
TEnorm
Resume
Off: Compressor stops.
Decrease: Decrease the running frequency to the lower level.
Hold: Keep the current frequency.
Resume: No limitation for frequency.
9.4.4 Auto-mode
This mode can be chosen with remote controller and the setting temperature can be changed between
17~30℃.
In auto mode, the machine will choose cooling, heating or fan-only mode according to ΔT (ΔT =T1-Ts).
ΔT=T1-Ts
Running mode
ΔT>1℃
Cooling
-1<ΔT≤1℃
Fan-only
ΔT≤-1℃
Heating
Indoor fan will run at auto fan of the relevant mode.
The louver operates same as in relevant mode.
If the machine switches mode between heating and cooling, the compressor will keep stopping for 15
minutes and then choose mode according to T1-Ts.
If the setting temperature is modified, the machine will choose running function again.
9.4.5 Drying mode
9.4.5.1
Indoor fan speed is fixed at breeze and can’t be changed. The louver angle is the same as
in cooling mode.
HKD DCI
47
Version
- 1
ELECTRONIC FUNCTION
9.4.5.2
Compressor running rules
T1-Ts
2.5
F7
2.0
1.5
F5
1.0
0.5
F3
0.0
F1
9.4.5.3 Low indoor room temperature protection
In drying mode, if room temperature is lower than 10℃, the compressor will stop and not resume until
room temperature exceeds 12℃.
9.4.5.4 Evaporator anti-freezing protection, condenser high temperature protection and outdoor unit
frequency limit are active and the same as that in cooling mode.
9.4.5.5 The outdoor fan operates the same as in cooling mode.
9.4.6 Forced operation function
9.4.6.1 Enter forced operation function:
When the machine is off, pressing the touch button will carry the machine to forced auto mode. If
pressing the button once again within 5 seconds, the machine will turn into forced cooling mode.
In forced auto, forced cooling or any other operation mode, pressing touch button will turn off the
machine.
9.4.6.2 In forced operation mode, all general protections and remote control are available.
9.4.6.3 Operation rules:
Forced cooling mode:
The compressor runs at F2 frequency and indoor fan runs as breeze. After running for 30 minutes. the
machine will turn to auto mode as 24℃ setting temperature.
Forced auto mode:
The action of forced auto mode is the same as normal auto mode with 24℃ setting temperature.
HKD DCI
48
Version
- 1
ELECTRONIC FUNCTION
9.4.7 Timer function
9.4.7.1 Timing range is 24 hours.
9.4.7.2 Timer on. The machine will turn on automatically when reaching the setting time.
9.4.7.3 Timer off. The machine will turn off automatically when reaching the setting time.
9.4.7.4 Timer on/off. The machine will turn on automatically when reaching the setting “on” time, and
then turn off automatically when reaching the setting “off” time.
9.4.7.5 Timer off/on. The machine will turn off automatically when reaching the setting “off” time, and
then turn on automatically when reaching the setting “on” time.
9.4.7.6 The timer function will not change the AC current operation mode. Suppose AC is off now, it will
not start up firstly after setting the “timer off” function. And when reaching the setting time, the timer
LED will be off and the AC running mode has not been changed.
9.4.7.7 The setting time is relative time.
9.4.8 Sleep function mode
9.4.8.1 Operation time in sleep mode is 7 hours. After 7 hours the AC quits this mode and turns off.
9.4.8.2. Operation process in sleep mode is as follow:
When cooling, the setting temperature rises 1℃ (be lower than 30℃) every one hour, 2 hours later the
setting temperature stops rising and indoor fan is fixed as low speed.
When heating, the setting temperature decreases 1℃ (be higher than 17℃) every one hour, 2 hours
later the setting temperature stops rising and indoor fan is fixed as low speed. (Anti-cold wind function
has the priority)
9.4.8.3 Timer setting is available
9.4.8.4 When user uses timer off function in sleep mode (or sleep function in timer off mode), if the
timing is less than 7 hours, sleep function will be cancelled when reaching the setting time. If the timing
is more than 7 hours, the machine will not stop until reaches the setting time in sleep mode.
9.4.9 Auto-Restart function
The indoor unit is equipped with auto-restart function, which is carried out through an auto-restart
module. In case of a sudden power failure, the module memorizes the setting conditions before the
power failure. The unit will resume the previous operation setting (not including swing function)
automatically after 3 minutes when power returns.
If the memorization condition is forced cooling mode, the unit will run in cooling mode for 30 minutes
HKD DCI
49
Version
- 1
ELECTRONIC FUNCTION
and turn to auto mode as 24℃ setting temp.
If AC is off before power off and AC is required to start up now, the compressor will have 1 minute
delay when power on. Other conditions, the compressor will have 3 minutes delay when restarts.
9.4.10 8℃ Heating
In heating operation, the preset temperature of the air conditioner can be as lower as 8℃, which keeps
the room temperature steady at 8℃ and prevents household things freezing when the house is
unoccupied for a long time in severe cold weather.
9.4.11 Frequency limitation protection
V
Normal
VOLT_RST1_ADD
VOLT_LIM1_ADD
VOLT_LIM_FREQ1_ADD
VOLT_RST2_ADD
VOLT_LIM2_ADD
VOLT_LIM_FREQ2_ADD
The PCB will detect the voltage of power supply and adjust the compressor running frequency to
protect the system.
In the first 10 seconds after power on, this protection is inactive.
When this protection happens, it will last 3 minutes and then the PCB will detect the power supply
voltage again.
HKD DCI
50
Version
- 1
TROUBLE SHOOTING
10. Troubleshooting
10.1 Indoor Unit Error Display
Operation lamp
Timer lamp
Display
LED STATUS
☆ 1 time
X
E0
Indoor unit EEPROM parameter error
☆ 2 times
X
E1
Indoor / outdoor units communication error
☆ 3 times
X
E2
☆ 4 times
X
E3
☆ 5 times
X
E4
Zero crossing signal detection error(only for AWSI-HKD009-N11
)
Indoor fan speed has been out of control
Open circuit or short circuit of indoor room temperature T1
sensor
Open circuit or short circuit of evaporator coil temperature T2
☆ 6 times
X
E5
sensor
☆ 7 times
X
EC
☆ 2 times
O
F1
Refrigerant Leakage Detection
Open circuit or short circuit of outdoor ambient T4 temperature
sensor
Open circuit or short circuit of condenser coil temperature T3
☆ 3 times
O
F2
sensor
Open circuit or short circuit of compressor discharge T5
☆ 4 times
O
F3
temperature sensor
☆ 5 times
O
F4
Outdoor unit EEPROM parameter error
☆ 6 times
O
F5
Outdoor fan speed has been out of control
☆ 1 times
☆
P0
IPM malfunction or IGBT over-strong current protection
☆ 2 times
☆
P1
Over voltage or over low voltage protection
☆ 3 times
☆
P2
High temperature protection of compressor top diagnosis and
solution(Only for AWSI-HKD024-N11 models)
☆ 5 times
☆
P4
O(light)
HKD DCI
Inverter compressor drive error
X(off)
51
☆(flash)
Version
- 1
TROUBLE SHOOTING
10.2 Diagnosis and Solution
10.2.1 EEPROM parameter error diagnosis and solution(E0)
Shut off the power supply and
turn it on 5 seconds later. Is it
still displaying the error code?
Yes
If the EEPROM chip
is welded on main
PCB, replace the
main PCB directly.
Otherwise, check
whether the
EEPROM chip
plugged in main PCB
well?
No
Correct the connection.
Yes
Replace the indoor main
PCB.
EEPROM: a read-only memory whose contents can be erased and reprogrammed using a pulsed
voltage.
HKD DCI
52
Version
- 1
TROUBLE SHOOTING
10.2.2 Indoor unit and outdoor unit communication protection error diagnosis and solution (E1)
Power off, then turn on the unit 5 seconds
later(reconnect the power wire).Is the error
still displaying after several minutes?
Yes
Check all the wirings between indoor and
outdoor, indoor main PCB and outdoor main
PCB following the wiring diagram. Are all
the wirings connected correctly?
Yes
Measure Vs, is it moving alternately
between positive value and negative
value?
(Vs is the voltage between S and N of
outdoor unit.)
No
Yes
Is the wiring to the outdoor m a i n
PCB connected correctly?
Is the wiring to the indoor main
PCB connected correctly?
Yes
Yes
Change the outdoor main PCB.
Change the indoor main PCB.
Power on. Is the error extinguished?
Power on. Is the error extinguished?
No
No
Change the indoor main PCB.
Change the outdoor main PCB.
HKD DCI
53
Version
- 1
TROUBLE SHOOTING
10.2.3 Zero crossing detection error diagnosis and solution(E2)
Check if the connections and
power supply is normal?
Correct the connections. Turn on the
unit when the power supply is good.
No
Yes
Indoor main PCB is
defective. Replace indoor
main PCB.
10.2.4 Fan speed has been out of control diagnosis and solution (E3/F5)
Shut off the power supply
and turn it on 5 seconds
later. Is it still displaying
the error code?
No
The unit operates normally.
Yes
Shut off the power supply,
rotate the fan by hand.
Does it rotate properly?
No
Find out the cause and
have it solved. For
example, check
whether the fan is
blocked or the bearing
is broken?
No
Correct the connections.
Yes
Check the wires of fan
motor. Are all the
connections good?
Yes
Check whether the fan
motor is normal through
index 1?
No
Replace the fan
motor
If the
malfunction is
still existing,
replace the
main PCB
No
Yes
Check whether the main PCB is
normal through index 2?
No
Replace the
main PCB.
The
malfunction is
solved?
Yes
HKD DCI
54
Version
- 1
TROUBLE SHOOTING
HKD DCI
55
Version
- 1
TROUBLE SHOOTING
Index 1:
1. Indoor AC Fan Motor
Measure the resistance value of each winding by using the tester.
2.Outdoor or indoor DC Fan Motor (control chip is in fan motor)
Measure the resistance value of each winding by using the tester. If any resistance value is zero, the
fan motor must have problems and need to be replaced.
3. Outdoor or indoor DC Fan Motor (control chip is in on PCB)
For WZDK36-38G-W
1) Release the UVW connector. Measure the resistance of U-V, U-W, V-W. If the resistance is not
equal to each other, the fan motor must has problems and need to be replaced. Otherwise, go to
step 2.
HKD DCI
56
Version
- 1
TROUBLE SHOOTING
For other motors:
NO.
1
2
3
4
5
Color
Orange
Grey
White
Pink
Black
Signal
Hu
Hv
Hw
Vcc
GND
Color
Red
Blue
Yellow
Signal
W
V
U
1) Release the UVW connector. Measure the resistance of U-V, U-W, V-W. If the resistance is not
equal to each other, the fan motor must has problems and need to be replaced. Otherwise, go to
step 2.
2) Power on and when the unit is in standby, measure the voltage of pin4-5 in feedback signal
connector. If the value is not 5V, change the PCB. Otherwise, go to step 3.
3) Rotate the fan by hand, measure the voltage of pin1-5, pin 2-5 and pin 3-5 in feedback signal
connector. If any voltage is not positive voltage fluctuation, the fan motor must has problems and
need to be replaced.
Index2:
1: Indoor AC Fan Motor
Power on and set the unit running in fan mode at high fan speed. After running for 15 seconds,
measure the voltage of pin1 and pin2. If the value of the voltage is less than 100V(208~240V power
supply)or 50V(115V power supply), the PCB must has problems and need to be replaced.
HKD DCI
57
Version
- 1
TROUBLE SHOOTING
2. Indoor or Outdoor DC Fan Motor(control chip is in fan motor)
Power on and when the unit is in standby, measure the voltage of pin1-pin3, pin4-pin3 in fan motor
connector. If the value of the voltage is not in the range showing in below table, the PCB must has
problems and need to be replaced.
DC motor voltage input and output
NO.
Color
Signal
Voltage
1
Red
Vs/Vm
280V~380V
2
---
---
---
3
Black
GND
0V
4
White
Vcc
14-17.5V
5
Yellow
Vsp
0~5.6V
6
Blue
FG
14-17.5V
HKD DCI
58
Version
- 1
TROUBLE SHOOTING
10.2.5 Open circuit or short circuit of temperature sensor diagnosis and solution
(E4/E5/F1/F2/F3)
Check the connections
between temperature
sensor and PCB. Are
the connections good?
No
Correct the connections.
Yes
Check the resistance value
of the sensor via table1
and table 2, is it normal?
Yes
Replace indoor or outdoor PCB.
No
Replace the sensor and
check if the problem
happen again?
HKD DCI
59
Version
- 1
TROUBLE SHOOTING
10.2.6 Refrigerant Leakage Detection diagnosis and solution (EC)
Shut off the power supply and
turn it on 5 seconds later. Is it
still displaying the error code?
Yes
Is there cool air blowing
out from indoor air outlet?
Yes
No
Yes
Is there any leakage? Especially
the connection parts, such as the
gas valve and the liquid valve.
No
Check if T2 sensor is well
fixed. Correct the installation
or replace T2 sensor. Does
the problem remain again?
Replace indoor PCB.
Yes
Repair the leakage and
recharge the refrigerant.
Is there any block i n g ? (Such as the
capillary or the welded points of the pipes.)
Yes
Clear the blocking.
HKD DCI
60
Version
- 1
TROUBLE SHOOTING
10.2.7 IPM malfunction or IGBT over-strong current protection diagnosis and solution(P0)
Check if the wiring between main
PCB and compressor connected by
error and if the wires and connectors
are broken?
Yes
Correct the connection or
replace the wires and
connectors.
No
Correct the installation,
tighten the screws and
apply silicon grease.
No
Check if the IPM installed correctly.
Yes
IPM continuity check. Check if the
IPM terminal resistance values are
uniform.
No
Replace the IPM board or replace
the main PCB if the IPM board and
main PCB are integrated together.
No
Refer to the solution of fan speed
has been out of control
malfunction . Find out the cause
and have it solved.
No
Replace the compressor.
Yes
Check if the outdoor fan runs
properly or the outdoor unit
ventilation is good.
Yes
Check if the compressor resistance
values are uniform .
Yes
Replace the outdoor main PCB if the
main PCB and IPM are separate.
HKD DCI
61
Version
- 1
TROUBLE SHOOTING
10.2.8 Over voltage or too low voltage protection diagnosis and solution(P1)
Check if the power supply is
normal.
No
Disconnect the unit with power
supply and try to restart the unit
when power supply gets normal.
No
Correct the connections or replace
the wires.
Yes
Check if all the connections
and wires are good?
Yes
Power on and when the unit is in
standby, check if the voltage
between P and N is around DC
310V or 340V or 380V? For different
kinds of units, the voltage differs.
Consult with technical engineer to
get definite value. Then start up the
unit, measure the voltage between
P and N. Is it in 220V~400V?
Replace the IPM board if it is separate
with main PCB.
No
Yes
Replace outdoor mainl PCB.
HKD DCI
62
Version
- 1
TROUBLE SHOOTING
10.2.9 High temperature protection of compressor top diagnosis and solution(P2)
Check if the air flow system
of indoor and outdoor units
are obstructed?
Clear up the air inlet and outlet or the heat
exchanger of indoor and outdoor units.
Yes
No
Turn off the power supply and turn
it on 10 minutes later.
Yes
Check if the unit can
start normally.
Check if all the connection, especially
the connection of OLP (Over Load
Protector) sensor is good.
No
Yes
Yes
Check if the refrigerant
charge volume is normal?
Measure the resistance
between the two ports of
the OLP. Is it zero?
No
No
Correct the connection.
Replace the OLP.
No
Yes
Yes
Refrigerant system is blocked, such
as capillary or welded point of pipes.
HKD DCI
Replace the outdoor control PCB.
Recharge the correct
refrigerant volume.
63
Version
- 1
TROUBLE SHOOTING
10.2.10 Inverter compressor drive error diagnosis and solution(P4)
Check if the wiring between main
PCB and compressor connected by
error and if the wires and connectors
are broken?
Yes
Correct the connection or
replace the wires and
connectors.
No
Correct the installation,
tighten the screws and
apply silicon grease.
No
Check if the IPM installed correctly.
Yes
IPM continuity check. Check if the
IPM terminal resistance values are
uniform.
No
Replace the IPM board or replace
the main PCB if the IPM board and
main PCB are integrated together.
No
Refer to the solution of fan speed
has been out of control
malfunction . Find out the cause
and have it solved.
No
Replace the compressor.
Yes
Check if the outdoor fan runs
properly or the outdoor unit
ventilation is good.
Yes
Check if the compressor resistance
values are uniform .
Yes
Replace the outdoor main PCB if the
main PCB and IPM are separate.
HKD DCI
64
Version
- 1
TROUBLE SHOOTING
Safety
Electricity power is still kept in capacitors even the power supply is shut off. Do not forget to discharge the electricity
power in capacitor.
Electrolytic Capacitors
(HIGH VOLTAGE! CAUTION!)
Connect discharge resistance (approx.100Ω 40W) or soldering iron (plug) between +, - terminals of the electrolytic
capacitor on the contrary side of the outdoor PCB.
Note: The picture above is only for reference. The plug of your side may be different.
Main parts check
1.
Temperature sensor checking
Disconnect the temperature sensor from PCB, measure the resistance value with a tester.
HKD DCI
65
Version
- 1
TROUBLE SHOOTING
Temperature Sensors.
Room temp.(T1) sensor,
Indoor coil temp.(T2) sensor,
Outdoor coil temp.(T3) sensor,
Outdoor ambient temp.(T4) sensor,
Compressor discharge temp.(T5) sensor.
Measure the resistance value of each winding by using the multi-meter.
Table 1: Some frequently-used R-T data for T1,T2,T3 and T4 sensor:
Temperature (℃)
5
10
15
20
25
30
40
50
60
Resistance Value (KΩ)
26.9
20.7
16.1
12.6
10
8
5.2
3.5
2.4
Table 2: Some frequently-used R-T data for T5 sensor:
Temperature (℃)
5
15
25
35
60
70
80
90
100
Resistance Value (KΩ)
141.6
88
56.1
36.6
13.8
9.7
6.9
5
3.7
Resistance value (KΩ)
T5
T1,T2,T3,T4
Temperature (℃)
HKD DCI
66
Version
- 1
TROUBLE SHOOTING
Spec.
Code
2T0032300899
2T0032400280
2T0032800707
2T0032900568
Model
AWSI-HKD009-N11
AWSI-HKD012-N11
AWSI-HKD018-N11
AWSI-HKD024-N11
Compressor
ASN108D22UEZ
ASN108D22UEZ
DA130M1C-31FZ
DA150S1C-20FZ
RPG20E
WZDK20-38G
WZDK30-38G
WZDK58-38G
(☆)
(☆)
(☆)
Indoor fan motor
Outdoor fan
WZDK36-38G-W
WZDK36-38G-W
WZDK36-38G-W
WZDK50-38G
motor
(★)
(★)
(★)
(☆)
Note: The motor marked “★”means DC fan motor with control chip in the PCB while the one marked “☆” means DC fan
motor with control chip in the fan motor.
HKD DCI
67
Version
- 1
TROUBLE SHOOTING
2. Compressor checking
Measure the resistance value of each winding by using the tester.
Position
Resistance Value
ASN108D22UEZ
DA130M1C-31FZ
DA150S1C-20FZ
Blue -
1.5Ω
1.77Ω
0.95Ω
Black
(20℃)
(20℃ )
(20℃ )
Blue - Red
Red - Blue
HKD DCI
68
Version
- 1
TROUBLE SHOOTING
3.IPM continuity check
Turn off the power, let the large capacity electrolytic capacitors discharge completely, and dismount the IPM. Use a
digital tester to measure the resistance between P and UVWN; UVW and N.
Digital tester
(+)Red
(-)Black
N
P
Normal resistance value
U
V
∞
(Several MΩ)
W
Digital tester
(+)Red
(-)Black
∞
U
V
Normal resistance value
N
(Several MΩ)
W
4.Indoor AC Fan Motor
Measure the resistance value of each winding by using the tester.
Position
Resistance Value
RPG20E
Black - Red
White - Black
HKD DCI
430Ω±8% (20℃)
388Ω±8% (20℃)
(Brand: Dayang)
(Brand: Weiling)
370Ω±8% (20℃)
360Ω±8% (20℃)
(Brand: Dayang)
(Brand: Weiling)
69
Version
- 1
TROUBLE SHOOTING
HKD DCI
70
Version
- 1
EXPLODED VIEW AND SPARE PART LIST
11. Exploded View
11.1 Indoor unit
AWSI-HKD009-N11
ONLY FOR STANDARD BOM, CUSTOMIZED FEATURE MAY CHANGE THE PART LIST
HKD DCI
71
Version
- 1
EXPLODED VIEW AND SPARE PART LIST
No.
Part Name
Quantity
BOM Code
1
Panel assembly
1
201132591038
3
Display box assembly
1
203332591125
3.1
Display board assembly
1
201333090687
4
Cover of electrical equipment
1
201119901024
5
Panel frame assembly
1
201132591041
5.1
Screw cap
2
201119900950
6
Drain hose
1
201101020038
7
Pipe Nut
1
201600330002
7
Pipe Nut
1
201600330001
8
Fix clamp of temperature sensor
1
201102000305
9
Evaporator assembly
1
201532390220
10
Fan motor cover
1
201132490127
11
Asynchronous motor
1
202400400213
12
Bearing holder
1
201119900952
13
Bearing base
1
202719900606
14
Cross flow fan
1
201100200306
15
Horizontal louver
1
201132591044
16
Chassis assembly
1
201132591057
16.1
Louver motor
1
202400200031
17
Pipe clamp board
1
201119900949
18
Installation plate
1
201232590037
19
Electronic control box assembly
1
203332391198
19.1
Electronic control box I
1
201132490125
19.2
Electronic control box II
1
201132490150
19.3
Indoor main control board assembly
1
201332391780
19.4
Ambient temperature sensor assembly
1
202433190000
19.5
Pipe temperature sensor assembly
1
202301300426
19.6
Wire joint
1
202301450119
20
Cover of electronic control box
1
201132490126
21
Remote Controller
1
203355000031
22
Seal ring
1
202720090001
23
Drain joint
1
201101020011
24
Air freshening filter
1
201131410703
25
Air filter(left)
1
201132591042
26
Air filter(right)
1
201132591040
HKD DCI
72
Version
- 1
EXPLODED VIEW AND SPARE PART LIST
AWSI-HKD012-N11
ONLY FOR STANDARD BOM, CUSTOMIZED FEATURE MAY CHANGE THE PART LIST
HKD DCI
73
Version
- 1
EXPLODED VIEW AND SPARE PART LIST
No.
Part Name
Quantity
BOM Code
1
Panel assembly
1
201132591038
3
Display box assembly
1
203332591125
3.1
Display board assembly
1
201333090687
4
Cover of electrical equipment
1
201119901024
5
Panel frame assembly
1
201132591041
5.1
Screw cap
2
201119900950
6
Drain hose
1
201101020038
7
Pipe Nut
1
201600330002
7
Pipe Nut
1
201600330001
8
Fix clamp of temperature sensor
1
201102000305
9
Evaporator assembly
1
201532390220
10
Fan motor cover
1
201132490127
11
Brushless DC Motor
1
202400370025
12
Bearing holder
1
201119900952
13
Bearing base
1
202719900606
14
Cross flow fan
1
201100200306
15
Horizontal louver
1
201132591044
16
Chassis assembly
1
201132591057
16.1
Louver motor
1
202400200031
17
Pipe clamp board
1
201119900949
18
Installation plate
1
201232590037
19
Electronic control box assembly
1
203332490311
19.1
Electronic control box I
1
201132490125
19.2
Electronic control box II
1
201132490150
19.3
Indoor main control board assembly
1
201332490360
19.4
Ambient temperature sensor assembly
1
202433190000
19.5
Pipe temperature sensor assembly
1
202301300426
19.6
Wire joint
1
202301450119
20
Cover of electronic control box
1
201132490126
21
Remote Controller
1
203355000031
22
Seal ring
1
202720090001
23
Drain joint
1
201101020011
24
Air freshening filter
1
201131410703
25
Air filter(left)
1
201132591042
26
Air filter(right)
1
201132591040
HKD DCI
74
Version
- 1
EXPLODED VIEW AND SPARE PART LIST
AWSI-HKD018-N11
ONLY FOR STANDARD BOM, CUSTOMIZED FEATURE MAY CHANGE THE PART LIST
HKD DCI
75
Version
- 1
EXPLODED VIEW AND SPARE PART LIST
No.
Part Name
Quantity
BOM Code
1
Panel assembly
1
201132790660
2
Air filter
2
201132790664
3
Display box assembly
1
203332890588
3.1
Display board assembly
1
201333090687
4
Cover of electrical equipment
1
201119901024
5
Panel frame assembly
1
201132790667
5.1
Screw cap
2
201119900950
6
Drain hose
1
201101020038
7
Pipe Nut
1
201600330003
7
Pipe Nut
1
201600330001
8
Fix clamp of temperature sensor
1
201102000305
9
Evaporator assembly
1
201532890160
10
Fan motor cover
1
201132790663
11
Brushless DC Motor
1
202400300517
12
Bearing holder
1
201119900952
13
Bearing base
1
202719900606
14
Cross flow fan
1
201100200322
15
Horizontal louver
1
201132790665
16
Chassis assembly
1
201132790680
16.1
Louver motor
1
202400200031
17
Pipe clamp board
1
201119900949
18
Installation plate
1
201232790013
19
Electronic control box assembly
1
203332890706
19.1
Electronic control box I
1
201132490125
19.2
Electronic control box II
1
201132490150
19.3
Indoor main control board assembly
1
201332890811
19.4
Ambient temperature sensor assembly
1
202433190000
19.5
Pipe temperature sensor assembly
1
202301300426
19.6
Wire joint
1
202301450119
20
Cover of electronic control box
1
201132490126
21
Remote Controller
1
203355000031
22
Seal ring
1
202720090001
23
Drain joint
1
201101020011
24
Air freshening filter
1
201131410703
HKD DCI
76
Version
- 1
EXPLODED VIEW AND SPARE PART LIST
AWSI-HKD024-N11
ONLY FOR STANDARD BOM, CUSTOMIZED FEATURE MAY CHANGE THE PART LIST
HKD DCI
77
Version
- 1
EXPLODED VIEW AND SPARE PART LIST
No.
Part Name
Quantity
BOM Code
1
Panel assembly
1
201133091036
2
Air filter(right)
1
201133091043
3
Air filter(left)
1
201133091044
4
Display box assembly
1
203333090474
4.1
Display board assembly
1
201333090687
5
Cover of electrical equipment
1
201133091048
6
Panel frame assembly
1
201133091041
6.1
Screw cap
3
201119900950
7
Horizontal louver
1
201133090987
8
Air outlet assembly
1
201133091126
8.1
Louver motor
1
202400200120
9
Drain hose
1
201101020038
10
Pipe Nut
1
201600330004
10
Pipe Nut
1
201600330002
11
Fix clamp of temperature sensor
1
201102000305
12
Evaporator assembly
1
201533090140
13
Fan motor cover
1
201133090980
14
Fixing board of fan motor
1
201133090167
15
Brushless DC Motor
1
202400300064
16
Bearing holder
1
201119900952
17
Bearing base
1
202719900606
18
Cross flow fan
1
201100200053
19
Chassis assembly
1
201133091040
20
Pipe clamp board
1
201232800103
21
Installation plate
1
201232590038
22
Electronic control box assembly
1
203333090559
22.1
Electronic control box I
1
201133091038
22.2
Indoor main control board assembly
1
201333090830
22.4
Ambient temperature sensor assembly
1
202433190000
22.5
Pipe temperature sensor assembly
1
202301300426
22.6
Wire joint
1
202301450119
23
Cover of electronic control box
1
201133091042
24
Remote Controller
1
203355000031
25
Seal ring
1
202720090001
26
Drain joint
1
201101020011
27
Air freshening filter
1
201131410703
HKD DCI
78
Version
- 1
EXPLODED VIEW AND SPARE PART LIST
11.1 Outdoor unit
AWAU-YKD009-H11
ONLY FOR STANDARD BOM, CUSTOMIZED FEATURE MAY CHANGE THE PART LIST
HKD DCI
79
Version
- 1
EXPLODED VIEW AND SPARE PART LIST
No.
Part Name
Quantity
BOM Code
2
Rear net
1
2011376G0001
3
Condenser assembly
1
201537591110
3.1
Input pipe assembly
1
201637400781
3.2
Condenser
1
201535260671
3.3
Output pipe
1
201648890033
5
Valve plate
1
201237300316
6
Chassis assembly
1
201237490041
7
Right clapboard assembly
1
201237390082
8
Big handle
1
201148100123
9
Water collector
1
201137390017
10
Front panel assembly
1
201237400429
10.1
Air outlet grille
1
201137590017
10.2
Front panel
1
201237400411
13
Axial flow fan
1
201100390002
14
Brushless DC Motor
1
202400300536
15
Supporter assembly of fan motor
1
201237400049
16
Partition board assembly
1
201237400423
17
Left supporter
1
201237400397
18
Supporter of fan motor holder
1
201237400055
19
Top cover assembly
1
201237400412
20
Electronic control box assembly
1
203337390261
20.2
Outdoor main control board assembly
1
201337390235
20.4
Radiator
1
202301901117
20.5
Electronic installing box
1
201137490028
21
Terminal board assembly
1
203337390276
21.1
Wire joint
1
202301400015
21.2
Terminal board
1
201237490039
22
4-ways valve assembly
1
201637391676
22.1
Gas valve
1
201600720094
22.2
4-ways valve
1
201600600521
23
Liquid valve assembly
1
201637490760
23.1
Liquid valve
1
201600700078
24
Compressor
1
201400611186
28
Reactor
1
202301000847
1
202301300801
1
201137490029
30
31
Compound temperature sensor
assembly
Cover of electronic control box
HKD DCI
80
Version
- 1
EXPLODED VIEW AND SPARE PART LIST
AWAU-YKD012-H11
ONLY FOR STANDARD BOM, CUSTOMIZED FEATURE MAY CHANGE THE PART LIST
HKD DCI
81
Version
- 1
EXPLODED VIEW AND SPARE PART LIST
HKD DCI
82
Version
- 1
EXPLODED VIEW AND SPARE PART LIST
No.
Part Name
Quantity
BOM Code
1
Ambient temperature sensor assembly
1
202301310075
2
Rear net
1
2011376G0001
3
Condenser assembly
1
201537591110
3.1
Input pipe assembly
1
201637400781
3.2
Condenser
1
201535260671
3.3
Output pipe
1
201648890033
4
Pipe temperature sensor assembly
1
202440500004
5
Valve plate
1
201237300316
6
Chassis assembly
1
201237490041
7
Right clapboard assembly
1
201237390082
8
Big handle
1
201148100123
9
Water collector
1
201137390017
10
Front panel assembly
1
201237400429
10.1
Air outlet grille
1
201137590017
10.2
Front panel
1
201237400411
13
Axial flow fan
1
201100390002
14
Brushless DC Motor
1
202400300536
15
Supporter assembly of fan motor
1
201237400049
16
Partition board assembly
1
201237400423
17
Left supporter
1
201237400397
18
Supporter of fan motor holder
1
201237400055
19
Top cover assembly
1
201237400412
20
Electronic control box assembly
1
203337590124
20.1
Cover of electronic control box
1
201237300162
20.2
Outdoor main control board assembly
1
201337590100
20.3
Support of electronic control box
1
201137300162
20.4
Radiator
1
202301990015
20.5
Electronic installing box
1
201237300033
21
Terminal board assembly
1
203337390276
21.1
Wire joint
1
202301400015
21.2
Terminal board
1
201237490039
22
4-ways valve assembly
1
201637391676
22.1
Gas valve
1
201600720094
22.2
4-ways valve
1
201600600521
23
Liquid valve assembly
1
201637490760
23.1
Liquid valve
1
201600700078
24
Compressor
1
201400611186
1
202301310068
1
202301000867
26
28
Discharge temperature sensor
assembly
Reactor
HKD DCI
83
Version
- 1
EXPLODED VIEW AND SPARE PART LIST
HKD DCI
84
Version
- 1
EXPLODED VIEW AND SPARE PART LIST
AWAU-YKD018-H11
ONLY FOR STANDARD BOM, CUSTOMIZED FEATURE MAY CHANGE THE PART LIST
HKD DCI
85
Version
- 1
EXPLODED VIEW AND SPARE PART LIST
No.
Part Name
Quantity
BOM Code
1
Ambient temperature sensor assembly
1
202301300115
2
Rear net
1
2011374G0003
3
Condenser assembly
1
201537390033
4
Pipe temperature sensor assembly
1
202440500004
5
Valve plate
1
201237200299
6
Chassis assembly
1
201237590104
7
Right clapboard assembly
1
201237500263
8
Big handle
1
201148100123
9
Water collector
1
201137400000
10
Air outlet grille
1
201137590017
12
Front panel
1
201237400392
13
Axial flow fan
1
201100390002
14
Brushless DC Motor
1
202400300536
15
Supporter assembly of fan motor
1
201237390026
16
Partition board assembly
1
201237500242
16.3
Reactor
1
202301000903
17
Left supporter
1
201237400400
18
Top cover assembly
1
201237900028
19
Electronic control box assembly
1
203337790154
19.1
Cover of electronic control box
1
201237300162
19.2
Outdoor main control board assembly
1
201337790084
19.3
Support of electronic control box
1
201137300162
19.4
Radiator
1
202301901222
19.5
Electronic installing box
1
201237300033
20
Terminal board assembly
1
203337590135
20.1
Wire joint
1
202301400015
20.2
Terminal board
1
201237590046
21
4-Ways valve assembly
1
201637891258
21.1
Gas valve
1
201600720195
21.2
4-Ways valve
1
201600690011
22
Liquid valve assembly
1
201637891260
22.1
Liquid valve
1
201600740523
23
Compressor
1
201400603269
1
202301310068
25
Discharge temperature sensor
assembly
HKD DCI
86
Version
- 1
EXPLODED VIEW AND SPARE PART LIST
AWAU-YKD024-H11
ONLY FOR STANDARD BOM, CUSTOMIZED FEATURE MAY CHANGE THE PART LIST
HKD DCI
87
Version
- 1
EXPLODED VIEW AND SPARE PART LIST
No.
Part Name
Quantity
BOM Code
1
Ambient temperature sensor assembly
1
202301300115
2
Rear net
1
2011481G0001
3
Condenser assembly
1
201537990084
3.1
Input pipe assembly
1
201637991011
3.2
Condenser
1
201537990003
3.3
Output pipe
1
201637991010
4
Pipe temperature sensor assembly
1
202301300111
5
Valve plate
1
201237300316
6
Chassis assembly
1
201257090054
7
Rear right clapboard assembly
1
201237990048
8
Big handle
1
201157390007
9
Water collector
1
201137390017
10
Front right clapboard assembly
1
201248100389
11
Front panel
1
201248100390
12
Air outlet grille
1
201138090006
13
Axial flow fan
1
201100300553
14
Brushless DC Motor
1
202400300535
15
Supporter assembly of fan motor
1
201257090067
16
Rear supporter
1
201248100384
17
Top cover assembly
1
201248100266
18
Left supporter
1
201248100367
19
Partition board assembly
1
201257190118
20
Electronic control box assembly
1
203338090356
20.1
Cover of electronic control box
1
201157190011
20.2
Outdoor main control board assembly
1
201338090096
20.3
Inverter control board
1
201338090092
20.4
Electronic installing plate
1
201157190010
20.5
Radiator
1
202301901173
21
Terminal board assembly
1
203337990358
21.1
Wire joint
1
202301450155
21.2
Terminal board
1
201257190117
22
Liquid valve assembly
1
201638091131
22.1
Liquid valve
1
201600740704
23
4-ways valve assembly
1
201638091130
23.1
Gas valve
1
201600720296
23.2
4-ways valve
1
201600690011
24
Compressor
1
201400600530
1
202448200000
1
202301000943
26
28
assembly
Discharge temperature sensor
assembly
Reactor
HKD DCI
88
Version
- 1
EXPLODED VIEW AND SPARE PART LIST
SERVICE MANUAL
HKD DCI Series
HKD DCI
89
Version
- 1
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising