HomeFill Oxygen Conserving Cylinder Operator’s Manual

HomeFill Oxygen Conserving Cylinder Operator’s Manual
Operator’s Manual
HomeFill™
Oxygen Conserving
Cylinder
HF2PCL6
HF2PC9
HF2PCL4
Dealer: This manual MUST be given to the end
user.
User: Before using this cylinder, read this
manual and save for future reference.
For more information regarding
Invacare products, parts, and services,
please visit www.invacare.com
WARNING
WARNING
DO NOT OPERATE THIS PRODUCT OR ANY
AVAILABLE OPTIONAL EQUIPMENT WITHOUT
FIRST COMPLETELY READING AND
UNDERSTANDING THESE INSTRUCTIONS AND
ANY ADDITIONAL INSTRUCTIONAL MATERIAL
SUCH AS OWNER’S MANUALS, SERVICE
MANUALS OR INSTRUCTION SHEETS SUPPLIED
WITH THIS PRODUCT OR OPTIONAL
EQUIPMENT. IF YOU ARE UNABLE TO
UNDERSTAND THE WARNINGS, CAUTIONS, OR
INSTRUCTIONS, CONTACT A HEALTHCARE
PROFESSIONAL, DEALER OR TECHNICAL
PERSONNEL BEFORE ATTEMPTING TO USE
THIS EQUIPMENT - OTHERWISE INJURY OR
DAMAGE MAY OCCUR.
ACCESSORIES WARNING
Invacare products are specifically designed and
manufactured for use in conjunction with Invacare
accessories. Accessories designed by other manufacturers
have not been tested by Invacare and are not
recommended for use with Invacare products.
NOTE: Updated versions of this manual are available on www.invacare.com.
HomeFill™
2
Part No 1112648
TABLE OF CONTENTS
TABLE OF CONTENTS
SPECIAL NOTES ..........................................................4
RECEIVING INSPECTION .............................................5
INTENDED USE ...........................................................5
SECTION 1—GENERAL GUIDELINES .............................6
Operating Information.............................................................................................6
Maintenance ................................................................................................................8
SECTION 2—FEATURES ...............................................9
SECTION 3—TYPICAL PRODUCT PARAMETERS ........10
SECTION 4—INSPECTION AND COMPRESSOR
INTERFACE ..............................................................11
Cylinder Prefill Inspection.................................................................................... 11
Connecting/Disconnecting the Cylinder to/from the Compressor....... 14
SECTION 5—OPERATING INSTRUCTIONS .................19
SECTION 6—MAINTENANCE ....................................21
SECTION 7—CYLINDER FILL TIMES ............................22
Troubleshooting...................................................................................................... 22
Replacement Parts - Accessories ...................................................................... 22
LIMITED WARRANTY ...............................................23
Part No 1112648
3
HomeFill™
SPECIAL NOTES
SPECIAL NOTES
Signal words are used in this manual and apply to hazards or unsafe practices which could result in personal injury or property damage. Refer to the following table for definitions of the signal words.
SIGNAL WORD
MEANING
DANGER
Danger indicates an imminently hazardous
situation which, if not avoided, will result in
death or serious injury.
WARNING
Warning indicates a potentially hazardous
situation which, if not avoided, could result
in death or serious injury.
CAUTION
Caution indicates a potentially hazardous
situation which, if not avoided, may result in
property damage or minor injury or both.
NOTICE
The information contained in this document is subject to change without notice.
DANGER
DO NOT SMOKE while using this device. Keep all matches, lit cigarettes or other sources of ignition out of the room in which this product is located and away from where oxygen is being delivered. NO SMOKING signs should be prominently displayed. Textiles and other materials that normally would not burn are easily ignited and burn with great intensity in oxygen enriched air. Failure to observe this warning can result in severe fire, property damage and cause physical injury or death.
HomeFill™
4
Part No 1112648
RECEIVING INSPECTION
CAUTION
“Caution: Federal law restricts this device to sale by or rental or on the order of a physician, or any other practitioner licensed by the law of the state in which he/she practices to use or order the use of this device.”
RECEIVING INSPECTION
Remove product from package and inspect for damage. If there is any damage, DO NOT use. Contact your dealer/ Home Care equipment provider.
INTENDED USE
To store, regulate, and deliver supplemental oxygen to patients who may have difficulty extracting oxygen from the air they breathe. It is for patients who would normally receive the oxygen via a nasal cannula. The device delivers USP 93% oxygen at a number of different flow/pulse settings. It is intended to be used as an oxygen saving device that may reduce the drying out of the airways. Part No 1112648
5
HomeFill™
SECTION 1—GENERAL GUIDELINES
SECTION 1—GENERAL GUIDELINES
In order to ensure the safe installation, assembly and operation of the HomeFill Oxygen Conserving Cylinder these instructions MUST be followed.
WARNING
This section contains important information for the safe operation
and use of this product.
Operating Information
Only personnel instructed and trained in the use of the HomeFill O2 Conserving Cylinder should operate this product.
Product contains magnetic, ferrous material that may affect the results of an MRI.
Be sure all connections are tight and leak free.
DO NOT autoclave.
DO NOT gas sterilize with ethylene oxide.
DO NOT clean with aromatic hydrocarbons.
DO NOT immerse product in any kind of liquid.
Store product in a clean area when not is use.
Only use Invacare Corporation HF2PCL6 carrying bag, HF2PC9 carrying bag, or HF2PCL4 carrying bag.
NEVER smoke in an area where oxygen is being administered.
ALWAYS confirm prescribed dose before administering to patient and monitor on a frequent basis.
DO NOT use if dirt or contaminants are present on or around cylinder, valve, product or connecting devices.
HomeFill™
6
Part No 1112648
SECTION 1—GENERAL GUIDELINES
NEVER use near any type of flame or flammable/explosive substances, vapors or atmosphere.
ALWAYS follow ANSI and CGA standards for Medical Gas Products and Flowmeters (E‐7) and Oxygen Handling (G‐4).
NO OXYGEN is delivered when the pointer is aligned with “Off”.
DO NOT block the outlet fitting or kink the cannula when the product is in use, this may damage the unit.
The use of this device is limited to the oxygen patient. Cylinders MUST be used only by the oxygen patient and are not to be distributed to any other individual for any purpose.
This product is NOT to be used by patients who breathe through their mouths.
DO NOT use oils, greases, organic lubricants or any combustible materials on or near this product. Wash and dry hands properly prior to usage.
DO NOT allow oil from your hands or other sources to come into contact with the compressor coupling or bottle fittings. These substances may become flammable in the presence of oxygen and cause injury. Avoid touching the bottle fitting whenever possible. Example of items to avoid are hand creams or lotions, cooking oils, suntan oils or sunblocks and similar oily products. If you use these types of products, wash your hands prior to using the HomeFill unit. If the bottle fitting should come in contact with such substances it should be cleaned off with a damp cloth prior to connecting it to the compressor.
NEVER oil or lubricate the compressor coupler or bottle fittings. NEVER use any penetrating oil or lubricant such as WD‐40® or 3‐in‐1 oil®. If connection difficulty is experienced verify that the bottle fitting is being inserted straight down into the compressor coupler. If continued difficulty is experienced contact your supplier for assistance.
Part No 1112648
7
HomeFill™
SECTION 1—GENERAL GUIDELINES
DO NOT use a humidifier with this product.
DO NOT allow cylinders to tip or fall. Secure gas cylinders so they cannot fall. Ensure cylinder is always in upright position.
DO NOT store cylinders near sources of heat or flame.
This product is equipped with a relief valve. If you hear a loud hissing or popping sound coming from the product, discontinue use of product, turn the flow selector to the “Off” position, and contact your dealer/Home Care equipment provider.
DO NOT use while sleeping without consulting your healthcare provider.
This product is designed to operate with a standard single lumen, adult oxygen nasal cannula with a maximum length of seven feet.
The cannula is for single patient use only.
Cannula MUST be installed on outlet connection prior to use.
DO NOT place the unit under clothing while in use. When this product is in use a small amount of oxygen is vented. Wearing the unit under clothing may saturate fabrics with oxygen and cause them to burn rapidly if exposed to sparks or flame. It may take several hours for oxygen levels in fabrics to return to normal.
Maintenance
DO NOT use a liquid leak detector to test for leaks.
DO NOT attempt to repair product.
HomeFill™
8
Part No 1112648
SECTION 2—FEATURES
SECTION 2—FEATURES
DANGER
This product is not intended as a life‐sustaining or life‐supporting device.
Outlet
Connection
Cannula
Flow Dial
Cylinder Fill
Port
Cylinder
Gauge
FIGURE 2.1 Product Diagram
Part No 1112648
9
HomeFill™
SECTION 3—TYPICAL PRODUCT PARAMETERS
SECTION 3—TYPICAL PRODUCT
PARAMETERS
CONSERVER S/N RANGE
1-69,999
75,000 +
INLET PRESSURE RANGE:
300 - 2100 psig
300 - 2100 psig
50 psig
50 psig
HF2PCL6: Weight
4.3 lbs (1.95 kg)
4.1 lbs (1.86 kg)
HF2PCL6: Overall Length
11.1 in (28 cm)
10.9 in (27.7 cm)
HF2PCL6: Diameter
4.4 in (11.1 cm)
4.4 in (11.1 cm)
HF2PC9: Weight
5.3 lbs (2.4 kg)
5.1 lbs (2.31 kg)
HF2PC9: Overall Length
14.2 in (36 cm)
14 in (35.5 cm)
HF2PC9: Diameter
4.4 in (11.1 cm)
4.4 in (11.1 cm)
HF2PCL4: Weight
N/A
3.6 lbs (1.63 kg)
HF2PCL4:Overall Length
N/A
8.9 in (22.2 cm)
HF2PCL4:Diameter.
N/A
4.4 in (11.1 cm)
INTERNAL REGULATED
PRESSURE:
DIMENSIONS:
PULSE SETTINGS:
1,2,3,4, & 5
FLOW SETTINGS:
2 LPM Continuous
SAVINGS RATIO:
Up to 4.3:1
Up to 5.7:1
CANNULA
REQUIREMENT:
4 ft recommended (MS0204) (7 ft long max)
std. adult single lumen oxygen nasal cannula.
OPERATING CONDITIONS TEMPERATURE:
32°F (0°C) to 105°F
(40.6°C)
35°F (1.7°C) to 105°F
(40.6°C)
0 to 5280 ft (0
to1600 m)
0 to 10,000 ft (0 to
3071 m)
-40°F (-40°C) to
140°F (60°C)
-40°F (-40°C) to 140°F
(60°C)
ALTITUDE:
STORAGE CONDITIONS
TEMPERATURE:
MAXIMUM HUMIDITY:
HomeFill™
95%
10
Part No 1112648
SECTION 4—INSPECTION AND COMPRESSOR INTERFACE
SECTION 4—INSPECTION AND
COMPRESSOR INTERFACE
NOTE: Refer to the HomeFill Compressor Owner’s Manual for compressor operating instructions.
Cylinder Prefill Inspection
WARNING
All cylinders MUST be inspected before attempting to fill; otherwise, injury or damage may occur.
NEVER smoke in an area where oxygen is being administered.
NEVER use near any type of flame or flammable/explosive substances, vapors or atmosphere.
NOTE: For this procedure, refer to FIGURE 4.1.
The Hydrostatic Testing Date
Aluminum cylinders MUST undergo testing every five years.
WARNING
DO NOT fill cylinders that have not been tested in the past five years. Otherwise, serious personal injury may result. Contact your dealer for replacement.
Part No 1112648
11
HomeFill™
SECTION 4—INSPECTION AND COMPRESSOR INTERFACE
External Examination
1. Examine the outside of the cylinder for the following conditions, and replace the cylinder if they exist:
• Dents or dings
• Arc Burns
• Oil or Grease
• Any other signs of damage that might cause a cylinder to be unacceptable or unsafe for use.
2. Examine the cylinder for evidence of fire or thermal damage. Evidence includes charring or blistering of the paint, or other protective coating or heat sensitive indicator. If fire or thermal damage is found, replace the cylinder.
3. Inspect the cylinder fillport for the following, and replace if found:
• Debris, oil or grease
• Noticeable signs of damage
• Signs of corrosion inside the valve
• Signs of excessive heat or fire damage
HomeFill™
12
Part No 1112648
SECTION 4—INSPECTION AND COMPRESSOR INTERFACE
Improper filling or abuse of this cylinder, or failure to follow these safety
instructions may cause serious bodily injury or death. High pressure
oxidizing gas vigorously accelerates combustion.
DO NOT alter or modify cylinder or related components.
DO NOT use oil or grease. Keep cylinder, cylinder valve, all equipment
and connections free of oil and grease to avoid violent ignition resulting
in serious bodily injury or death.
For medical applications. Use only as directed by a licensed
practitioner. Uninterrupted use of high concentrations of oxygen over
a long duration, without monitoring its effect on oxygen content of
arterial blood, may be harmful.
Oxygen Cylinders filled by the Invacare HomeFill oxygen
system shall be used for personal use only. "Not to be
filled for resale or use by professional users."
This cylinder is to be used with the Invacare HomeFill
oxygen system. This cylinder contains 93 ± 3% oxygen
produced by an oxygen concentrator using the pressure swing
adsorption process.
DO NOT handle cylinder or use contents until you are professionally
trained, including emergency procedures.
Use in accordance with Invacare HomeFill oxygen system Operator’s
Manual. Open valve slowly. Close valve after each use and when
empty. Secure cylinder during storage and use. No smoking in cylinder
area. Keep away from heat, flame and spark. Keep out of reach of
children. DO NOT drop.
Filling of this gas is performed by Invacare HomeFill oxygen system
Only.
Cylinders that have been refinished and/or exposed to elevated
temperatures must be hydrostatically tested before filling. Cylinder
temperature should not exceed 125°F (52°C). Aluminum cylinders
subject to the action of fire or heated to temperatures in excess of
350°F must be withdrawn from service and condemned by trained
personnel. DO NOT use caustic paint strippers. Valve and safety
relief devices must be removed and replaced by trained and
authorized personnel. DO NOT alter or change valve assembly.
Invacare Corporation
2101 E. Lake Mary Blvd.
Sanford, FL 32773
1-800-832-4707
DO NOT REMOVE THIS PRODUCT LABEL
Not for Commercial Resale
Part Number 1125090 Rev D
FIGURE 4.1 External Examination
Part No 1112648
13
HomeFill™
SECTION 4—INSPECTION AND COMPRESSOR INTERFACE
Connecting/Disconnecting the Cylinder
to/from the Compressor
Connecting the Cylinder to the Compressor
WARNING
NEVER use tools of any kind to connect/disconnect the cylinder and the compressor. Otherwise, severe injury and/or damage may occur.
DO NOT drop oxygen cylinders. Use two hands when handling/transporting oxygen cylinders. Otherwise, injury or damage may occur.
DO NOT use a liquid leak detector to test for leaks.
NOTE: For this procedure, refer to FIGURE 4.2 and FIGURE 4.3.
1. Examine the cylinder gauge. If the cylinder pressure is less than 1500 psig., proceed to STEP 2 (FIGURE 4.3).
NOTE: If the cylinder pressure is greater than 1500 psig., DO NOT attempt to top off this cylinder. It may not fill.
2. Set the regulator flow dial on the cylinder to OFF (FIGURE 4.3).
3. Remove the cylinder and connector fillport covers (if present).
CAUTION
DO NOT connect the outlet (cannula) connection to the HomeFill unit, otherwise the conserving cylinder will not work properly.
4. Momentarily push DOWN on the outer ring (sleeve) of the connector fillport to reset the connector as shown in FIGURE 4.2.
HomeFill™
14
Part No 1112648
SECTION 4—INSPECTION AND COMPRESSOR INTERFACE
NOTE: If the outer ring (sleeve) is in the UP position (GREEN dots not visible), the connector fillport will not be able to accept the cylinder fillport. Pushing DOWN momentarily will reset the connector fillport (GREEN dots visible) to accept the cylinder fillport.
PUSH
DOWN
Outer Ring (Sleeve)
Connector Fillport
GREEN Dots
BEFORE
COUPLING
CYLINDER,
PUSH DOWN
ON SLEEVE
UNTIL
GREEN DOTS
ARE VISIBLE.
FIGURE 4.2 Resetting Connector Fillport
5. Grasp the cylinder/regulator assembly in the area behind the cylinder gauge (FIGURE 4.3).
6. Position the cylinder in the compressor cradle (FIGURE 4.3).
7. Align the cylinder fillport with the connector fillport (FIGURE 4.3).
8. Pull UP on the outer ring (sleeve) of the connector fillport while pushing DOWN on the cylinder/regulator assembly to couple the cylinder fillport into the connector fillport (FIGURE 4.3).
NOTE: The cylinder is properly connected when an audible “click” is heard.
Part No 1112648
15
HomeFill™
SECTION 4—INSPECTION AND COMPRESSOR INTERFACE
Compressor
Cylinder/Regulator
Assembly
Cylinder
Fillport
Connector
Fillport
Outer Ring
(Sleeve)
Cylinder
Gauge
PULL UP
Regulator
Cylinder
Cylinder
Gauge
Regulator
Flow Dial
Outlet (Cannula)
Connection
Cylinder
Fillport
Power
Switch
Compressor
Cradle
Outer Ring
(Sleeve)
Connector
Fillport
NOTE: Fillport covers not shown for clarity.
FIGURE 4.3 Connecting the Cylinder to the Compressor
HomeFill™
16
Part No 1112648
SECTION 4—INSPECTION AND COMPRESSOR INTERFACE
Disconnecting the Cylinder from the Compressor
WARNING
NEVER use tools of any kind to connect/disconnect the cylinder and the compressor. Otherwise, severe injury and/or damage may occur.
NOTE: For this procedure, refer to FIGURE 4.4.
1. Press the compressor power switch to the Off (O) position.
2. Grasp the cylinder/regulator assembly in the area behind the cylinder gauge.
3. With the other hand, grasp the outer ring (sleeve) of the connector fillport and push DOWN.
4. Lift up on the cylinder/regulator assembly to remove from the connector fillport.
Cylinder/Regulator
Assembly
Cylinder
Gauge
Compressor
Cylinder
Fillport
PUSH DOWN
Outer Ring
(Sleeve)
Connector
Fillport
FIGURE 4.4 Disconnecting the Cylinder from the Compressor
Part No 1112648
17
HomeFill™
SECTION 4—INSPECTION AND COMPRESSOR INTERFACE
5. When the cylinder fillport is disconnected from the connector fillport, release the outer ring (sleeve) of the connector fillport and use two hands to remove the cylinder from the compressor cradle.
6. Place the fillport covers onto the connector and cylinder fillports.
NOTE: The fillport covers should be used whenever cylinders are not being filled.
HomeFill™
18
Part No 1112648
SECTION 5—OPERATING INSTRUCTIONS
SECTION 5—OPERATING
INSTRUCTIONS
WARNING
NEVER smoke in an area where oxygen is being administered.
NEVER use near any type of flame or flammable/explosive substances, vapors or atmosphere.
NOTE: For this procedure, refer to FIGURE 5.1.
1. Prior to each use, inspect product for visible damage. DO NOT use if any damage is found.
NOTE: If for any reason, any label becomes illegible or lost, contact your dealer/Home Care equipment provider. 2. Be sure regulator is in the “Off” position. Align “Off” with the indicating pointer.
3. Position the cylinder so the oxygen cylinder valve outlet is pointing away from the user and any other person(s). WARNING
DO NOT direct flow of oxygen at any person, or flammable material when adjusting the flow dial.
4. Attach a standard adult single lumen oxygen nasal cannula, no longer than seven feet to the product’s outlet according to the cannula manufacturer’s instructions. DO NOT use pediatric, low flow nasal cannulas or oxygen masks with this product.
NOTE: A unit without cannula attached may pulse if set at position 1‐5.
Part No 1112648
19
HomeFill™
SECTION 5—OPERATING INSTRUCTIONS
5. Place the cannula over your ears and position the prongs in your nose as instructed by your Health Care provider or cannula manufacturer. Refer to FIGURE 5.1.
6. Turn dial until indicating pointer is aligned with the prescribed setting.
FIGURE 5.1 Cannula
Placement
WARNING
When pointer on contents gauge enters red zone, it is recommended to refill the cylinder on the Invacare HomeFill Compressor.
NO OXYGEN is delivered in between settings. To obtain desired flow, the indicating pointer must align with a specific number on the dial.
To avoid injury to patient, ALWAYS confirm prescribed setting before administering to patient and monitor flow on a frequent basis.
Only use Invacare Corporation HF2PCL6 carrying bag, the HF2PC9 carrying bag, or the HF2PCL4 carrying bag. 7. Breathe through the nose and feel a pulse of oxygen as you inhale.
NOTE: When on a pulse setting, there is flow or a pulse only at the beginning of each breath. If you do not feel the pulse at the beginning of each breath, check the setting.
NOTE: Because each patient’s breathing pattern is different and the environment varies, it may be difficult to feel some low setting pulses.
HomeFill™
20
Part No 1112648
SECTION 6—MAINTENANCE
SECTION 6—MAINTENANCE
1. After each use, clean exterior of the product with a dry, lint free cloth only.
2. Store product in a clean area free from grease, oil, and other sources of contamination.
CAUTION
DO NOT use cleaning solutions. DO NOT immerse product in any kind of liquid. All repairs MUST be done by Invacare Corporation.
Part No 1112648
21
HomeFill™
SECTION 7—CYLINDER FILL TIMES
SECTION 7—CYLINDER FILL TIMES
NOTE: All filling times are approximate and may vary on environmental conditions.
*
Cylinder
Filling
Times
Concentrator Flow Rate to Patient:
(Platinum 5 up to 3 L/min. and Platinum 10 up to 5
L/min)
HF2PC9
HF2PCL4
HF2PCL6
NORMAL
2 hr 20 min
60 min
1 hr 25 min
MAXIMUM
2 hr 45 min
1 hr 20 min
1 hr 50 min
Troubleshooting
If Conserving Cylinder fails to function, consult the Troubleshooting guide. If problem cannot be corrected, consult your Dealer/Home Care equipment provider.
PROBLEM
No flow.
POSSIBLE CAUSE
SOLUTION
1. Regulator in “Off”
position.
1. Set to prescribed
setting.
2. Cylinder empty.
2. Replace/fill cylinder.
3. Dial not set at increment.
3. Set dial so indictor
points to a setting.
4. Conserver not sensing breath.
4. Check position of
cannula in nose. Do not
breathe through mouth.
5. Check to see if the
cannula is kinked.
Replacement Parts - Accessories
HF2PCL6 Carrying Bag, HF2PC9 Carrying Bag, or HF2PCL4 Carrying Bag
HomeFill™
22
Part No 1112648
LIMITED WARRANTY
LIMITED WARRANTY
PLEASE NOTE: THE WARRANTY BELOW HAS BEEN DRAFTED TO
COMPLY WITH FEDERAL LAW APPLICABLE TO PRODUCTS
MANUFACTURED AFTER JULY 4, 1975.
This warranty is extended only to the original purchaser/user of our products.
This warranty gives you specific legal rights and you may also have other legal
rights which vary from state to state.
Invacare warrants this product to be free from defects in materials and
workmanship for a period of three years from date of purchase. If within such
warranty period any such product shall be proven to Invacare’s satisfaction to
be defective, such product shall be repaired or replaced, at Invacare’s option.
This warranty does not apply to problems arising from normal wear and tear
or failure to adhere to these instructions, nor does it include shipping charges
incurred in replacement part installation or repair of any such product.
Invacare’s sole obligation and your exclusive remedy under this warranty
shall be limited to such repair and/or replacement.
For warranty service, please contact the Invacare service department during
normal business hours at the toll-free telephone number identified on the
back cover of this manual.
Upon receiving notice of an alleged defect in a product, Invacare will issue a
serialized return authorization. It shall be the responsibility of the purchaser
to pack the product(s) or part(s) in an appropriate manner to avoid shipping
damage and return the product(s) or part(s), at the purchaser’s expense, to
either Invacare’s plant or service center as specified by Invacare in advance.
The defective product(s) or component part(s) must be returned for
warranty inspection using the serial number as identification within 30 days of
the return authorization date. DO NOT return any product(s) or part(s) to
our factory or service center without prior consent. C.O.D. shipments will be
refused – please pre-pay shipping charges.
LIMITATIONS AND EXCLUSIONS: THE FOREGOING WARRANTY
SHALL NOT APPLY TO SERIAL NUMBERED PRODUCTS IF THE SERIAL
NUMBER HAS BEEN REMOVED OR DEFACED; PRODUCTS SUBJECTED
TO NEGLIGENCE, ACCIDENT, IMPROPER OPERATION,
MAINTENANCE, OR STORAGE; PRODUCTS MODIFIED WITHOUT
INVACARE’S EXPRESS WRITTEN CONSENT (INCLUDING, BUT NOT
LIMITED TO, MODIFICATION THROUGH THE USE OF
UNAUTHORIZED PARTS OR ATTACHMENTS); PRODUCTS DAMAGED
BY REASON OF REPAIRS MADE TO ANY COMPONENT WITHOUT THE
SPECIFIC CONSENT OF INVACARE; PRODUCTS DAMAGED BY
CIRCUMSTANCES BEYOND INVACARE’S CONTROL; OR PRODUCTS
REPAIRED BY ANYONE OTHER THAN INVACARE OR AN INVACARE
SERVICE CENTER. SUCH EVALUATION SHALL BE SOLELY
DETERMINED BY INVACARE.
Part No 1112648
23
HomeFill™
THE FOREGOING EXPRESS WARRANTY IS EXCLUSIVE AND IN LIEU
OF ANY OTHER WARRANTIES WHATSOEVER, WHETHER EXPRESSED
OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE,
AND THE SOLE REMEDY FOR VIOLATIONS OF ANY WARRANTY
WHATSOEVER, SHALL BE LIMITED TO REPAIR OR REPLACEMENT OF
THE DEFECTIVE PRODUCT PURSUANT TO THE TERMS CONTAINED
HEREIN. THE APPLICATION OF ANY IMPLIED WARRANTY
WHATSOEVER SHALL NOT EXTEND BEYOND THE DURATION OF
THE EXPRESS WARRANTY PROVIDED HEREIN. INVACARE SHALL
NOT BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL
DAMAGES WHATSOEVER.
SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGE, OR LIMITATION OF
HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE
EXCLUSION AND LIMITATION MAY NOT BE APPLICABLE.
THIS WARRANTY SHALL BE EXTENDED TO COMPLY WITH
STATE/PROVINCIAL LAWS AND REQUIREMENTS.
Invacare Corporation
www.invacare.com
USA
One Invacare Way
Elyria, Ohio USA
44036-2125
440-329-6000
800-333-6900
Technical Services
440-329-6593
800-832-4707
© 2011 Invacare Corporation. All rights
reserved. Republication, duplication or
modification in whole or in part is
prohibited without prior written
permission from Invacare. Trademarks
are identified by ™ and ®. All trademarks are owned by or licensed to
Invacare Corporation or its subsidiaries
unless otherwise noted.
3-in-1 Oil is a registered trademark of
American Home Products Corporation.
WD-40 is a registered trademark of the
WD-40 Company.
Part No 1112648
Rev G - 1/11
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement