Zanussi | ZERC 2620 | Specifications | Zanussi ZERC 2620 Specifications

REFRIGERATOR
ZERC 2620
© Electrolux plc 2005
INSTRUCTION BOOKLET
2223 373-11
IMPORTANT SAFETY INFORMATION
It is most important that this instruction book should be retained with the appliance for future
reference. Should the appliance be sold or transferred to another owner, or should you move house and
leave the appliance, always ensure that the book is left with the appliance in order that the new owner
can get to know the functioning of the appliance and the relevant safety information.
This information has been provided in the interest of safety. You MUST read it carefully before installing
or using the appliance.
Installation
•
Frozen food must NOT be re-frozen once it has
thawed out.
•
•
Do not place carbonated or fizzy drinks in the
freezer.
•
Do not remove items from the freezer if your
hands are damp/wet, as this could cause skin
abrasions or frost/freezer burns.
•
Ice lollies can cause ‘frost/freezer burns’ if
consumed straight from the freezer.
•
Manufacturers’ storage recommendations should
be strictly adhered to. Refer to relevant
instructions.
•
The cooling plate or refrigerated freezer shelves
in this appliance contain channels through which
the refrigerant passes. If these are punctured this
will cause substantial damage to the appliance
and result in food loss. DO NOT USE SHARP
INSTRUMENTS to scrape off frost or ice. Under
NO circumstances should solid ice be forced off
the lining or shelves. Solid ice should be allowed
to thaw, when defrosting the appliance. See
Defrost Instructions.
•
•
•
•
•
This appliance is heavy. Care should be taken when
moving it.
It is dangerous to alter the specifications or attempt
to modify this product in any way.
Care must be taken to ensure that the appliance
does not stand on the electrical supply cable.
Important: if the supply cable is damaged, it must
be replaced by a special cable available from your
local Service Force Centre.
Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.
Parts which heat up should not be exposed.
Whenever possible, the back of the appliance
should be close to a wall but leaving the required
distance for ventilation as stated in the installation
instructions.
The appliance should be left for 2 hours after
installation before it is turned on, in order to allow
the refrigerant to settle.
Child Safety
•
Do not allow children to tamper with the controls or
play with the product.
Maintenance and Cleaning
•
Keep all packaging well away from children.
•
General Safety
•
•
•
•
•
This appliance contains hydrocarbons in its
cooling unit; maintenance and recharging must
therefore only be carried out by authorized
technicians.
Take utmost care when handling your appliance
so as not to cause any damages to the cooling
unit with consequent possible fluid leakages.
The appliance must not be located close to
cookers, radiators or boilers.
Avoid prolonged exposure of the appliance to
direct sunlight.
Do not use other electrical appliances (such as
ice cream makers) inside of refrigerating
appliances.
During Use
•
2
This appliance is designed for domestic use only,
specifically for the storage of edible foodstuffs.
Switch off and unplug the appliance before
carrying out any cleaning or maintenance work.
Servicing
•
This product should be serviced by an authorised
engineer and only genuine spare parts should be
used.
•
Under no circumstances should you attempt to
repair the machine yourself. Repairs carried out
by inexperienced persons may cause injury or
serious malfunctioning. Refer to your local
Service Force Centre and always insist on
genuine spare parts.
At the end of the Appliance
Life
•
When disposing of your appliance, use an
authorised disposal site.
•
Remove the plug and ensure that any locks or
catches are removed, to prevent young children
being trapped inside.
Disposal of old Appliances
Door reversal directions
1. Disconnect from the electricity supply.
2. Remove all loose items, including food, store food
in a cool place.
3. Gently lay the fridge/freezer on its back with the
top held away from the floor by 5-8 cm (2-3
inches) of packing;
G
4. Remove the feet (3)
5. Remove bottom hinge (1).
6. Slide out the door from pin (G), unscrew the latter
and then screw it down into the hinge provided on
the opposite side, after having removed the small
plugs which should then be fitted on the opposite
side.
CONTENTS
7. Refit the door and bottom hinge (1) on the
opposite side.
3
8. Refit the feet (3) on the opposite side.
9. Unscrew the handle. Refit it on the opposite side
after having pierced the plugs with a punch. Cover
the holes left open with the plugs contained in the
documentation pack.
Attention
Instructions for the User
1
2
D715 PIED/M
After completion of the door reversiing operation,
check that the door gasket adheres to the cabinet. If
the ambient temperature is cold (i.e. in Winter), the
gasket may not fit perfectly to the cabinet. In that
case, wait for the natural fitting of the gasket or
accelerate this process by heating up the part
involved with a normal hairdryer.
PR228
14
The symbol
on the product or on its packaging
indicates that this product may not be treated as
household waste. Instead it shall be handed over to
the applicable collection point for the recycling of
electrical and electronic equipment. By ensuring this
product is disposed of correctly, you will help prevent
potential negative consequences for the environment
and human health, which could otherwise be caused
by inappropriate waste handling of this product. For
more detailed information about recycling of this
product, please contact your local city office, your
household waste disposal service or the shop where
you purchased the product.
Important Safety Information
2
Instructions for the
Installer
Operation
4
Technical Specification
11
Before use
4
Installation
12
Setting the temperature
4
Positioning
12
Fresh food refrigeration
4
Rear Spacers
12
Normal operating sounds
4
Electrical Connection
13
Movable shelves
5
Positioning the door shelves
5
Door Reversal
14
Hints and Tips
6
Maintenance and Cleaning
6
Internal cleaning
6
External cleaning
6
When the appliance is not in use
6
Changing the light bulb
7
Defrosting
7
Something Not Working
8
Service and Spare Parts
9
Customer Care
9
Guarantee Conditions
10
3
OPERATION
Electrical connections
Fresh food refrigeration
Remove all securing tapes. Wash inside the
appliance with lukewarm water and bicarbonate of
soda (5 ml to 0.5 litre of water).
To obtain the best performance, do not store warm
food or evaporating liquids in the refrigerator; do
cover or wrap the food, particularly if it has a strong
flavour.
Do not use soap or detergent as the smell may
linger. Dry thoroughly.
Setting the temperature
The temperature inside the refrigerator is regulated
by a thermostat with 6 temperature positions and an
“OFF” (O) position.
Position 1 = minimum coldness
Position 6 = maximum coldness
Do not cover the shelves with any protective
material, such as paper, cardboard or plastic, which
may obstruct the air circulation through them.
To help you use your refrigerator correctly, here are
some more useful hints:
Raw meat (beef, pork, lamb & poultry or chicken):
wrap in polythene bags and place on the glass shelf
above the salad crispers.
Turn the thermostat dial to the required position.
Meat can only be stored safely in this way for
one or two days at the most.
The intermediate position is usually the most
suitable (3-4).
Fruit & vegetables: these should be thoroughly
cleaned and placed in the bottom salad crispers.
The thermostat setting can vary as the temperature
inside the refrigeration compartment depends on the
following factors:
Butter & cheese: these should be placed in special
airtight containers or wrapped in aluminium foil or
polythene bags to exclude as much air as possible.
– room temperature
Milk bottles: these should have a cap and should be
stored in the bottle rack on the door.
– how often the door is opened
– how much food is stored
– position of the appliance
Normal Operating Sounds
Important
During prolonged periods of abnormally hot weather,
if the thermostat is set on too high a number, the
cooling system may operate continuously and the
fridge cooling plate may not defrost. Turning the knob
to a lower number will cause the automatic
defrosting to resume.
•
You may hear faint gurgling or bubbling sounds
when the refrigerant is pumped through the coils
or tubing at the rear, to the cooling
plate/evaporator.
•
When the compressor is on, the refrigerant is
being pumped round, and you will hear a whirring
sound or pulsating noise from the compressor.
•
A thermostat controls the compressor, and you
will hear a faint ’click’ when the thermostat cuts in
and out.
Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.
The plug must not be used if the fuse cover/carrier is
lost. The cover/carrier is indicated by the coloured
insert at the base of the plug.
WARNING: THIS APPLIANCE MUST BE
EARTHED.
A replacement cover/carrier must be obtained from
your local Service Force Centre.
The manufacturer declines any liability should
this safety measure not be observed.
This appliance complies with the E.E.C. Directive
No. 87/308 of 2.6.87 relative to radio interference
suppression.
If the plug that is fitted to your appliance is not
suitable for your socket outlet, it must be cut off and
the appropriate plug fitted.
This appliance complies with the following
E.E.C. Directives:
Remove the fuse from the cut off plug.
-
The cut off plug should then be disposed of to
prevent the hazard of shocks in case it should be
plugged into a 13amp socket in another part of your
home.
73/23 EEC of 19.2.73 (Low Voltage Directive)
and subsequent modifications;
-
89/336 EEC of 3.5.89 (Electromagnetic
Compatibility Directive) and subsequent
modifications.
Important
The wires in the mains lead are coloured in
accordance with the following code:
Green and Yellow
- Earth
Blue
- Neutral
Brown
- Live
If you fit your own plug, the colours of the wires in
the mains lead of your appliance may not correspond
with the markings identifying the terminals in your
plug, proceed as follows:
GREEN & YELLOW
13 AMP. FUSE
13 AMP
Before using
The plug moulded onto the lead incorporates a fuse.
For replacement, use a 13amp BSI362 fuse. Only
ASTA or BSI approved fuses should be used.
BROWN
BLUE
D207
CORD CLAMP
Connect the Green and Yellow (earth) wire to the
terminal in the plug which is marked with the letter
«E» or the earth symbol
yellow.
or coloured green and
Connect the blue (neutral) wire to the terminal in the
plug which is marked with the letter «N» or coloured
black.
Connect the brown (live) wire to the terminal in the
plug which is marked with the letter «L» or coloured
red.
4
13
INSTALLATION
Important
IF YOU ARE DISCARDING AN OLD APPLIANCE
THAT HAS A LOCK OR CATCH ON THE DOOR,
YOU MUST ENSURE THAT IT IS MADE
UNUSABLE TO PREVENT YOUNG CHILDREN
BEING TRAPPED INSIDE.
Movable shelves
Depending upon the position which you choose for
your appliance, you may wish to reverse the way in
which the door opens. To do this, refer to instructions
on “Door reversal”.
The walls of the refrigerator have runners so that
shelves can be positioned as desired.
Please ensure that when the appliance is
installed it is easily accessible for the engineer in
the event of a breakdown.
D338
Positioning
This appliance should only be installed at a location
where the ambient temperature corresponds to the
climate classification indicated on the rating plate,
which is located at the left on the inside of the
appliance.
Positioning the door shelves
To permit storage of food packages of various sizes,
the door shelves can be adjusted in height.
The following table shows which ambient
temperature is correct for each climate classification:
+16°C to + 32°C
ST
+18°C to + 38°C
T
+18°C to + 43°C
It should be located in a dry atmosphere, out of
direct sunlight and away from extreme temperature
e.g. not next to a boiler or radiator, or in a very cold
room e.g. an outhouse, where the temperatures may
fall below 10°C (50°F). If these temperatures are
exceeded i.e. colder or warmer, then the appliance
may not operate correctly.
A
B
10 mm
N
100 mm
+10°C to + 32°C
10 mm
SN
To do this proceed as shown in the diagram.
NP007
You should also ensure that air can circulate freely
around the back and the top of the cabinet. There
must also be at least 100 mm (4”) distance between
the top of the cabinet and any overhanging kitchen
furniture (A). Ideally, the appliance should not be
positioned beneath overhanging furniture (B).
There should also be a gap of 25 mm either side of
the appliance. Do not obstruct the space
underneath. The back of the cabinet may be placed
close to the wall but must not touch it. DO NOT
install in places with restricted ventilation.
Adjust the level of the appliance by screwing out the
adjustable foot, or feet, at the bottom of the cabinet
using your fingers or a tool (see figure).
D200
Rear spacers
The plastic bag containing all relevant
documentation also contains two spacers to be fitted
into special holes in the back of the appliance.
Fit the spacers into the holes, taking care to ensure
that the arrow (A) is positioned as shown in the
Figure. Then turn them through 45° (arrow (A)
vertical) until they lock into place.
12
A
45°
PR60
5
TECHNICAL SPECIFICATIONS
HINTS AND TIPS
Food Storage
•
•
To obtain the best results from the appliance
neither hot foods nor liquids which may
evaporate, should be placed in the larder
compartment.
Energy Saving Advice
•
Do not install the appliance close to sources of
heat, such as a boiler or radiator.
•
Locate the appliance in a cool well ventilated
room and make sure that the air openings of the
appliance are not obstructed.
Keep the time between buying chilled food and
placing it in your refrigerator as short as possible.
•
Do not push food together too much, try to allow
air to circulate around each item.
•
Do not store food uncovered.
•
Remove suspect food from your refrigerator and
clean, refer to Maintenance and Cleaning.
•
•
Always leave warm food to cool down to room
temperature before placing in the fridge.
Try to avoid keeping the door open for long
periods or opening the door too frequently as
warm air will enter the cabinet and cause the
compressor to switch on unnecessarily often.
•
Ensure there are no obstructions preventing the
door from closing properly.
•
It is advisable to periodically clean the
refrigeration system at the back of the appliance
with a duster or vacuum cleaner.
DIMENSIONS
Height
140
cm
Width
55
cm
Depth
60
cm
POWER SUPPLY VOLTAGE AND FREQUENCY
220-240 V / 50 Hz
TOTAL POWER ABSORBED
90 W
AVERAGE DAILY UNITS ELECTRICITY *
0.619 kWh
GROSS CAPACITY
263 l
NET CAPACITY
260 l
* This figure is based on standard test results in accordance with European Standard EN 153.
Actual consumption will depend on how the appliance is used and where it is located.
MAINTENANCE AND CLEANING
Before any maintenance or cleaning work is carried
out, DISCONNECT the appliance from the
ELECTRICITY supply.
An accumulation of dust will affect the performance
of the appliance and cause excessive electricity
consumption.
You MUST ensure that the appliance is switched
OFF.
Internal cleaning
Clean the inside and accessories with warm water
and bicarbonate of soda (5ml to 0.5 litre of water).
Rinse and dry thoroughly.
Once or twice a year dust the condenser (black grill)
and the compressor at the back of the appliance,
with a brush or vacuum cleaner, see figure.
NEVER USE DETERGENTS, ABRASIVE
POWDERS, HIGHLY PERFUMED CLEANING
PRODUCTS OR WAX POLISHES, TO CLEAN THE
INTERIOR AS THESE WILL DAMAGE THE
SURFACE AND LEAVE A STRONG ODOUR.
External cleaning
Many proprietary kitchen surface cleaners
contain chemicals that can attack/damage the
plastics used in this appliance. For this reason it
is recommended that the outer casing of this
appliance is only cleaned with warm water with a
little washing-up liquid added.
6
PR259
When the appliance is not in use
When the appliance is not in use for long periods,
disconnect from the electricity supply, empty all
foods and clean the appliance, leaving the doors ajar
to prevent unpleasant smells.
11
GUARANTEE CONDITIONS
Standard guarantee conditions
We, Zanussi Electrolux, undertake that if within 12 months of the date of the purchase this ZANUSSI
ELECTROLUX appliance or any part thereof is proved to be defective by reason only of faulty workmanship or
materials, we will, at our option repair or replace the same FREE OF CHARGE for labour, materials or carriage
on condition that:
•
The appliance has been correctly installed and used only on the electricity supply stated on the rating plate.
•
The appliance has been used for normal domestic purposes only, and in accordance with the manufacturer’s
instructions.
•
The appliance has not been serviced, maintained, repaired, taken apart or tampered with by any person not
authorised by us.
•
All service work under this guarantee must be undertaken by a Service Force Centre. Any appliance or
defective part replaced shall become the Company’s property.
•
This guarantee is in addition to your statutory and other legal rights.
Changing the light bulb
Unscrew the light cover and then pull it outward
toward the middle of the cabinet.
Unscrew the bulb and replace it with one of the same
power (the maximum power is shown on the light
diffuser).available from your nearest Service Force
Centre.
Replace the light cover by sliding it into its original
position and replacing the screw.
D411
Home visits are made between 8.30am and 5.30pm Monday to Friday. Visits may be available outside these
hours in which case a premium will be charged.
Exclusions
This guarantee does not cover:
•
Damage or calls resulting from transportation, improper use or neglect, the replacement of any light bulbs or
removable parts of glass or plastic.
•
Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside
the European Community (EC) or European Free Trade Area.
•
Appliances found to be in use within a commercial environment, plus those which are subject to rental
agreements.
•
Products of Zanussi Electrolux manufacture which are not marketed by Zanussi Electrolux.
European Guarantee
If you should move to another country within Europe then your guarantee moves with you to your new home
subject to the following qualifications:
•
The guarantee starts from the date you first purchased your product.
•
The guarantee is for the same period and to the same extent for labour and parts as exists in the new
country of use for this brand or range of products.
•
This guarantee relates to you and cannot be transferred to another user.
•
Your new home is within the European Community (EC) or European Free Trade Area.
•
The product is installed and used in accordance with our instructions and is only used domestically, i.e. a
normal household.
•
The product is installed taking into account regulations in your new country.
Defrosting
The refrigerator automatically defrosts every time the
compressor stops. The water is discharged, via the
pipe, into a tray located at the back of the appliance
above the compressor, where it evaporates.
Important
To avoid defrost water overflowing into the fridge,
periodically clean the water discharge hole in the
centre of the V shaped drip collector at the back of
the refrigerator compartment behind the salad
crispers. Use the defrost cleaner provided which you
will find already inserted into the discharge hole.
D037
Remember to wash the defrost cleaner in hot soapy
water at regular intervals. Dry thoroughly before
replacing.
Before you move please contact your nearest Customer Care centre, listed below, to give them details of your
new home. They will then ensure that the local Service Organisation is aware of your move and able to look
after you and your appliances.
France
Senlis
+33 (0)3 44 62 29 29
Germany
Nürnberg
+49 (0)800 234 7378
Italy
Pordenone
+39 (0)0434 39 4700
Sweden
Stockholm
+46 (0)8 672 53 90
UK
Luton
+44 (0)8705 727727
Ireland
Dublin
+353 (0)1 4090751
10
7
SOMETHING NOT WORKING
If the appliance is not working correctly, please carry out the following checks before contacting your local
Service Force Centre
SERVICE AND SPARE PARTS
In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact your local
Service Force Centre by telephoning:-
0 8 7 0
5
9 2 9 9 2 9
Symptom
Solution
No power to the appliance
Check there is power at the socket.
For the address of your local Service Force Centre and further information about Service Force, please visit the
website at www.serviceforce.co.uk
Check there is not a power cut by checking the
household lights.
For Customer Service in Ireland please
Check the fuse has not blown.
The light does not come on
Your telephone call will be automatically routed to the Service Force Centre covering your post code area.
contact us at the address below:
Zanussi Electrolux
Ensure that the bulb is correctly fitted.
Electrolux Group (Irl) Ltd
Replace the bulb if it has blown.
Long Mile Road
Dublin 12
Check the door light switch is not jammed.
The temperature in the fridge is too cold
Check the thermostat control knob in the fridge is
turned to the correct setting relative to ambient
conditions.
Check the ambient temperature is within the
appliance’s operating limits, please refer to the
installation section in this instruction book.
Relocate the appliance if necessary.
The compressor runs continuously
Adjust the thermostat control knob to give correct
temperature control. See “Setting the temperature”.
Check that the door is closed.
Large quantities of food have recently been placed in
the cabinet and/or door is frequently opened.
Republic of Ireland
Telephone : +353 (0)1 4090751
Email: service.eid@electrolux.ie
Before calling out an engineer, please ensure you have read the details under the heading ‘Something Not
Working?
When you contact the Service Force Centre you will need to give the following details:
1.
Your name, address and post code
2.
Your telephone number
3.
Clear and concise details of the fault
4.
The model and serial number of the appliance (found on the rating plate)
5.
The purchase date
Check that air ventilation is not obstructed.
Noise
Refer to normal operating sounds.
Water under the salad crispers
Check the drain hole is not blocked. (see
Maintenance and Cleaning).
If after the above checks your appliance still does not operate correctly, contact your local Service Force Centre.
Please note that it will be necessary to provide proof of purchase for any in-guarantee service calls.
In-guarantee customers should ensure that the above checks have been made, as the engineer will
make a charge if the fault is not a mechanical or electrical breakdown.
Please note that a valid purchase receipt or guarantee documentation is required for in-guarantee
service calls.
CUSTOMER CARE DEPARTMENT
For general enquiries concerning your Zanussi Electrolux appliance or for further information on Zanussi
Electrolux products, please contact our Customer Care Department by letter or telephone at the address below
or visit our website at www.zanussi-electrolux.co.uk
Customer Care Department
Zanussi-Electrolux Major Appliances
Addington Way
Luton
Bedfordshire
LU4 9QQ
Tel: 08705 727 727 (*)
* calls to this number may be recorded for training purposes.
8
9
SOMETHING NOT WORKING
If the appliance is not working correctly, please carry out the following checks before contacting your local
Service Force Centre
SERVICE AND SPARE PARTS
In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact your local
Service Force Centre by telephoning:-
0 8 7 0
5
9 2 9 9 2 9
Symptom
Solution
No power to the appliance
Check there is power at the socket.
For the address of your local Service Force Centre and further information about Service Force, please visit the
website at www.serviceforce.co.uk
Check there is not a power cut by checking the
household lights.
For Customer Service in Ireland please
Check the fuse has not blown.
The light does not come on
Your telephone call will be automatically routed to the Service Force Centre covering your post code area.
contact us at the address below:
Zanussi Electrolux
Ensure that the bulb is correctly fitted.
Electrolux Group (Irl) Ltd
Replace the bulb if it has blown.
Long Mile Road
Dublin 12
Check the door light switch is not jammed.
The temperature in the fridge is too cold
Check the thermostat control knob in the fridge is
turned to the correct setting relative to ambient
conditions.
Check the ambient temperature is within the
appliance’s operating limits, please refer to the
installation section in this instruction book.
Relocate the appliance if necessary.
The compressor runs continuously
Adjust the thermostat control knob to give correct
temperature control. See “Setting the temperature”.
Check that the door is closed.
Large quantities of food have recently been placed in
the cabinet and/or door is frequently opened.
Republic of Ireland
Telephone : +353 (0)1 4090751
Email: service.eid@electrolux.ie
Before calling out an engineer, please ensure you have read the details under the heading ‘Something Not
Working?
When you contact the Service Force Centre you will need to give the following details:
1.
Your name, address and post code
2.
Your telephone number
3.
Clear and concise details of the fault
4.
The model and serial number of the appliance (found on the rating plate)
5.
The purchase date
Check that air ventilation is not obstructed.
Noise
Refer to normal operating sounds.
Water under the salad crispers
Check the drain hole is not blocked. (see
Maintenance and Cleaning).
If after the above checks your appliance still does not operate correctly, contact your local Service Force Centre.
Please note that it will be necessary to provide proof of purchase for any in-guarantee service calls.
In-guarantee customers should ensure that the above checks have been made, as the engineer will
make a charge if the fault is not a mechanical or electrical breakdown.
Please note that a valid purchase receipt or guarantee documentation is required for in-guarantee
service calls.
CUSTOMER CARE DEPARTMENT
For general enquiries concerning your Zanussi Electrolux appliance or for further information on Zanussi
Electrolux products, please contact our Customer Care Department by letter or telephone at the address below
or visit our website at www.zanussi-electrolux.co.uk
Customer Care Department
Zanussi-Electrolux Major Appliances
Addington Way
Luton
Bedfordshire
LU4 9QQ
Tel: 08705 727 727 (*)
* calls to this number may be recorded for training purposes.
8
9
GUARANTEE CONDITIONS
Standard guarantee conditions
We, Zanussi Electrolux, undertake that if within 12 months of the date of the purchase this ZANUSSI
ELECTROLUX appliance or any part thereof is proved to be defective by reason only of faulty workmanship or
materials, we will, at our option repair or replace the same FREE OF CHARGE for labour, materials or carriage
on condition that:
•
The appliance has been correctly installed and used only on the electricity supply stated on the rating plate.
•
The appliance has been used for normal domestic purposes only, and in accordance with the manufacturer’s
instructions.
•
The appliance has not been serviced, maintained, repaired, taken apart or tampered with by any person not
authorised by us.
•
All service work under this guarantee must be undertaken by a Service Force Centre. Any appliance or
defective part replaced shall become the Company’s property.
•
This guarantee is in addition to your statutory and other legal rights.
Changing the light bulb
Unscrew the light cover and then pull it outward
toward the middle of the cabinet.
Unscrew the bulb and replace it with one of the same
power (the maximum power is shown on the light
diffuser).available from your nearest Service Force
Centre.
Replace the light cover by sliding it into its original
position and replacing the screw.
D411
Home visits are made between 8.30am and 5.30pm Monday to Friday. Visits may be available outside these
hours in which case a premium will be charged.
Exclusions
This guarantee does not cover:
•
Damage or calls resulting from transportation, improper use or neglect, the replacement of any light bulbs or
removable parts of glass or plastic.
•
Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside
the European Community (EC) or European Free Trade Area.
•
Appliances found to be in use within a commercial environment, plus those which are subject to rental
agreements.
•
Products of Zanussi Electrolux manufacture which are not marketed by Zanussi Electrolux.
European Guarantee
If you should move to another country within Europe then your guarantee moves with you to your new home
subject to the following qualifications:
•
The guarantee starts from the date you first purchased your product.
•
The guarantee is for the same period and to the same extent for labour and parts as exists in the new
country of use for this brand or range of products.
•
This guarantee relates to you and cannot be transferred to another user.
•
Your new home is within the European Community (EC) or European Free Trade Area.
•
The product is installed and used in accordance with our instructions and is only used domestically, i.e. a
normal household.
•
The product is installed taking into account regulations in your new country.
Defrosting
The refrigerator automatically defrosts every time the
compressor stops. The water is discharged, via the
pipe, into a tray located at the back of the appliance
above the compressor, where it evaporates.
Important
To avoid defrost water overflowing into the fridge,
periodically clean the water discharge hole in the
centre of the V shaped drip collector at the back of
the refrigerator compartment behind the salad
crispers. Use the defrost cleaner provided which you
will find already inserted into the discharge hole.
D037
Remember to wash the defrost cleaner in hot soapy
water at regular intervals. Dry thoroughly before
replacing.
Before you move please contact your nearest Customer Care centre, listed below, to give them details of your
new home. They will then ensure that the local Service Organisation is aware of your move and able to look
after you and your appliances.
France
Senlis
+33 (0)3 44 62 29 29
Germany
Nürnberg
+49 (0)800 234 7378
Italy
Pordenone
+39 (0)0434 39 4700
Sweden
Stockholm
+46 (0)8 672 53 90
UK
Luton
+44 (0)8705 727727
Ireland
Dublin
+353 (0)1 4090751
10
7
TECHNICAL SPECIFICATIONS
HINTS AND TIPS
Food Storage
•
•
To obtain the best results from the appliance
neither hot foods nor liquids which may
evaporate, should be placed in the larder
compartment.
Energy Saving Advice
•
Do not install the appliance close to sources of
heat, such as a boiler or radiator.
•
Locate the appliance in a cool well ventilated
room and make sure that the air openings of the
appliance are not obstructed.
Keep the time between buying chilled food and
placing it in your refrigerator as short as possible.
•
Do not push food together too much, try to allow
air to circulate around each item.
•
Do not store food uncovered.
•
Remove suspect food from your refrigerator and
clean, refer to Maintenance and Cleaning.
•
•
Always leave warm food to cool down to room
temperature before placing in the fridge.
Try to avoid keeping the door open for long
periods or opening the door too frequently as
warm air will enter the cabinet and cause the
compressor to switch on unnecessarily often.
•
Ensure there are no obstructions preventing the
door from closing properly.
•
It is advisable to periodically clean the
refrigeration system at the back of the appliance
with a duster or vacuum cleaner.
DIMENSIONS
Height
140
cm
Width
55
cm
Depth
60
cm
POWER SUPPLY VOLTAGE AND FREQUENCY
220-240 V / 50 Hz
TOTAL POWER ABSORBED
90 W
AVERAGE DAILY UNITS ELECTRICITY *
0.619 kWh
GROSS CAPACITY
263 l
NET CAPACITY
260 l
* This figure is based on standard test results in accordance with European Standard EN 153.
Actual consumption will depend on how the appliance is used and where it is located.
MAINTENANCE AND CLEANING
Before any maintenance or cleaning work is carried
out, DISCONNECT the appliance from the
ELECTRICITY supply.
An accumulation of dust will affect the performance
of the appliance and cause excessive electricity
consumption.
You MUST ensure that the appliance is switched
OFF.
Internal cleaning
Clean the inside and accessories with warm water
and bicarbonate of soda (5ml to 0.5 litre of water).
Rinse and dry thoroughly.
Once or twice a year dust the condenser (black grill)
and the compressor at the back of the appliance,
with a brush or vacuum cleaner, see figure.
NEVER USE DETERGENTS, ABRASIVE
POWDERS, HIGHLY PERFUMED CLEANING
PRODUCTS OR WAX POLISHES, TO CLEAN THE
INTERIOR AS THESE WILL DAMAGE THE
SURFACE AND LEAVE A STRONG ODOUR.
External cleaning
Many proprietary kitchen surface cleaners
contain chemicals that can attack/damage the
plastics used in this appliance. For this reason it
is recommended that the outer casing of this
appliance is only cleaned with warm water with a
little washing-up liquid added.
6
PR259
When the appliance is not in use
When the appliance is not in use for long periods,
disconnect from the electricity supply, empty all
foods and clean the appliance, leaving the doors ajar
to prevent unpleasant smells.
11
INSTALLATION
Important
IF YOU ARE DISCARDING AN OLD APPLIANCE
THAT HAS A LOCK OR CATCH ON THE DOOR,
YOU MUST ENSURE THAT IT IS MADE
UNUSABLE TO PREVENT YOUNG CHILDREN
BEING TRAPPED INSIDE.
Movable shelves
Depending upon the position which you choose for
your appliance, you may wish to reverse the way in
which the door opens. To do this, refer to instructions
on “Door reversal”.
The walls of the refrigerator have runners so that
shelves can be positioned as desired.
Please ensure that when the appliance is
installed it is easily accessible for the engineer in
the event of a breakdown.
D338
Positioning
This appliance should only be installed at a location
where the ambient temperature corresponds to the
climate classification indicated on the rating plate,
which is located at the left on the inside of the
appliance.
Positioning the door shelves
To permit storage of food packages of various sizes,
the door shelves can be adjusted in height.
The following table shows which ambient
temperature is correct for each climate classification:
+16°C to + 32°C
ST
+18°C to + 38°C
T
+18°C to + 43°C
It should be located in a dry atmosphere, out of
direct sunlight and away from extreme temperature
e.g. not next to a boiler or radiator, or in a very cold
room e.g. an outhouse, where the temperatures may
fall below 10°C (50°F). If these temperatures are
exceeded i.e. colder or warmer, then the appliance
may not operate correctly.
A
B
10 mm
N
100 mm
+10°C to + 32°C
10 mm
SN
To do this proceed as shown in the diagram.
NP007
You should also ensure that air can circulate freely
around the back and the top of the cabinet. There
must also be at least 100 mm (4”) distance between
the top of the cabinet and any overhanging kitchen
furniture (A). Ideally, the appliance should not be
positioned beneath overhanging furniture (B).
There should also be a gap of 25 mm either side of
the appliance. Do not obstruct the space
underneath. The back of the cabinet may be placed
close to the wall but must not touch it. DO NOT
install in places with restricted ventilation.
Adjust the level of the appliance by screwing out the
adjustable foot, or feet, at the bottom of the cabinet
using your fingers or a tool (see figure).
D200
Rear spacers
The plastic bag containing all relevant
documentation also contains two spacers to be fitted
into special holes in the back of the appliance.
Fit the spacers into the holes, taking care to ensure
that the arrow (A) is positioned as shown in the
Figure. Then turn them through 45° (arrow (A)
vertical) until they lock into place.
12
A
45°
PR60
5
OPERATION
Electrical connections
Fresh food refrigeration
Remove all securing tapes. Wash inside the
appliance with lukewarm water and bicarbonate of
soda (5 ml to 0.5 litre of water).
To obtain the best performance, do not store warm
food or evaporating liquids in the refrigerator; do
cover or wrap the food, particularly if it has a strong
flavour.
Do not use soap or detergent as the smell may
linger. Dry thoroughly.
Setting the temperature
The temperature inside the refrigerator is regulated
by a thermostat with 6 temperature positions and an
“OFF” (O) position.
Position 1 = minimum coldness
Position 6 = maximum coldness
Do not cover the shelves with any protective
material, such as paper, cardboard or plastic, which
may obstruct the air circulation through them.
To help you use your refrigerator correctly, here are
some more useful hints:
Raw meat (beef, pork, lamb & poultry or chicken):
wrap in polythene bags and place on the glass shelf
above the salad crispers.
Turn the thermostat dial to the required position.
Meat can only be stored safely in this way for
one or two days at the most.
The intermediate position is usually the most
suitable (3-4).
Fruit & vegetables: these should be thoroughly
cleaned and placed in the bottom salad crispers.
The thermostat setting can vary as the temperature
inside the refrigeration compartment depends on the
following factors:
Butter & cheese: these should be placed in special
airtight containers or wrapped in aluminium foil or
polythene bags to exclude as much air as possible.
– room temperature
Milk bottles: these should have a cap and should be
stored in the bottle rack on the door.
– how often the door is opened
– how much food is stored
– position of the appliance
Normal Operating Sounds
Important
During prolonged periods of abnormally hot weather,
if the thermostat is set on too high a number, the
cooling system may operate continuously and the
fridge cooling plate may not defrost. Turning the knob
to a lower number will cause the automatic
defrosting to resume.
•
You may hear faint gurgling or bubbling sounds
when the refrigerant is pumped through the coils
or tubing at the rear, to the cooling
plate/evaporator.
•
When the compressor is on, the refrigerant is
being pumped round, and you will hear a whirring
sound or pulsating noise from the compressor.
•
A thermostat controls the compressor, and you
will hear a faint ’click’ when the thermostat cuts in
and out.
Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.
The plug must not be used if the fuse cover/carrier is
lost. The cover/carrier is indicated by the coloured
insert at the base of the plug.
WARNING: THIS APPLIANCE MUST BE
EARTHED.
A replacement cover/carrier must be obtained from
your local Service Force Centre.
The manufacturer declines any liability should
this safety measure not be observed.
This appliance complies with the E.E.C. Directive
No. 87/308 of 2.6.87 relative to radio interference
suppression.
If the plug that is fitted to your appliance is not
suitable for your socket outlet, it must be cut off and
the appropriate plug fitted.
This appliance complies with the following
E.E.C. Directives:
Remove the fuse from the cut off plug.
-
The cut off plug should then be disposed of to
prevent the hazard of shocks in case it should be
plugged into a 13amp socket in another part of your
home.
73/23 EEC of 19.2.73 (Low Voltage Directive)
and subsequent modifications;
-
89/336 EEC of 3.5.89 (Electromagnetic
Compatibility Directive) and subsequent
modifications.
Important
The wires in the mains lead are coloured in
accordance with the following code:
Green and Yellow
- Earth
Blue
- Neutral
Brown
- Live
If you fit your own plug, the colours of the wires in
the mains lead of your appliance may not correspond
with the markings identifying the terminals in your
plug, proceed as follows:
GREEN & YELLOW
13 AMP. FUSE
13 AMP
Before using
The plug moulded onto the lead incorporates a fuse.
For replacement, use a 13amp BSI362 fuse. Only
ASTA or BSI approved fuses should be used.
BROWN
BLUE
D207
CORD CLAMP
Connect the Green and Yellow (earth) wire to the
terminal in the plug which is marked with the letter
«E» or the earth symbol
yellow.
or coloured green and
Connect the blue (neutral) wire to the terminal in the
plug which is marked with the letter «N» or coloured
black.
Connect the brown (live) wire to the terminal in the
plug which is marked with the letter «L» or coloured
red.
4
13
Disposal of old Appliances
Door reversal directions
1. Disconnect from the electricity supply.
2. Remove all loose items, including food, store food
in a cool place.
3. Gently lay the fridge/freezer on its back with the
top held away from the floor by 5-8 cm (2-3
inches) of packing;
G
4. Remove the feet (3)
5. Remove bottom hinge (1).
6. Slide out the door from pin (G), unscrew the latter
and then screw it down into the hinge provided on
the opposite side, after having removed the small
plugs which should then be fitted on the opposite
side.
CONTENTS
7. Refit the door and bottom hinge (1) on the
opposite side.
3
8. Refit the feet (3) on the opposite side.
9. Unscrew the handle. Refit it on the opposite side
after having pierced the plugs with a punch. Cover
the holes left open with the plugs contained in the
documentation pack.
Attention
Instructions for the User
1
2
D715 PIED/M
After completion of the door reversiing operation,
check that the door gasket adheres to the cabinet. If
the ambient temperature is cold (i.e. in Winter), the
gasket may not fit perfectly to the cabinet. In that
case, wait for the natural fitting of the gasket or
accelerate this process by heating up the part
involved with a normal hairdryer.
PR228
14
The symbol
on the product or on its packaging
indicates that this product may not be treated as
household waste. Instead it shall be handed over to
the applicable collection point for the recycling of
electrical and electronic equipment. By ensuring this
product is disposed of correctly, you will help prevent
potential negative consequences for the environment
and human health, which could otherwise be caused
by inappropriate waste handling of this product. For
more detailed information about recycling of this
product, please contact your local city office, your
household waste disposal service or the shop where
you purchased the product.
Important Safety Information
2
Instructions for the
Installer
Operation
4
Technical Specification
11
Before use
4
Installation
12
Setting the temperature
4
Positioning
12
Fresh food refrigeration
4
Rear Spacers
12
Normal operating sounds
4
Electrical Connection
13
Movable shelves
5
Positioning the door shelves
5
Door Reversal
14
Hints and Tips
6
Maintenance and Cleaning
6
Internal cleaning
6
External cleaning
6
When the appliance is not in use
6
Changing the light bulb
7
Defrosting
7
Something Not Working
8
Service and Spare Parts
9
Customer Care
9
Guarantee Conditions
10
3
IMPORTANT SAFETY INFORMATION
It is most important that this instruction book should be retained with the appliance for future
reference. Should the appliance be sold or transferred to another owner, or should you move house and
leave the appliance, always ensure that the book is left with the appliance in order that the new owner
can get to know the functioning of the appliance and the relevant safety information.
This information has been provided in the interest of safety. You MUST read it carefully before installing
or using the appliance.
Installation
•
Frozen food must NOT be re-frozen once it has
thawed out.
•
•
Do not place carbonated or fizzy drinks in the
freezer.
•
Do not remove items from the freezer if your
hands are damp/wet, as this could cause skin
abrasions or frost/freezer burns.
•
Ice lollies can cause ‘frost/freezer burns’ if
consumed straight from the freezer.
•
Manufacturers’ storage recommendations should
be strictly adhered to. Refer to relevant
instructions.
•
The cooling plate or refrigerated freezer shelves
in this appliance contain channels through which
the refrigerant passes. If these are punctured this
will cause substantial damage to the appliance
and result in food loss. DO NOT USE SHARP
INSTRUMENTS to scrape off frost or ice. Under
NO circumstances should solid ice be forced off
the lining or shelves. Solid ice should be allowed
to thaw, when defrosting the appliance. See
Defrost Instructions.
•
•
•
•
•
This appliance is heavy. Care should be taken when
moving it.
It is dangerous to alter the specifications or attempt
to modify this product in any way.
Care must be taken to ensure that the appliance
does not stand on the electrical supply cable.
Important: if the supply cable is damaged, it must
be replaced by a special cable available from your
local Service Force Centre.
Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.
Parts which heat up should not be exposed.
Whenever possible, the back of the appliance
should be close to a wall but leaving the required
distance for ventilation as stated in the installation
instructions.
The appliance should be left for 2 hours after
installation before it is turned on, in order to allow
the refrigerant to settle.
Child Safety
•
Do not allow children to tamper with the controls or
play with the product.
Maintenance and Cleaning
•
Keep all packaging well away from children.
•
General Safety
•
•
•
•
•
This appliance contains hydrocarbons in its
cooling unit; maintenance and recharging must
therefore only be carried out by authorized
technicians.
Take utmost care when handling your appliance
so as not to cause any damages to the cooling
unit with consequent possible fluid leakages.
The appliance must not be located close to
cookers, radiators or boilers.
Avoid prolonged exposure of the appliance to
direct sunlight.
Do not use other electrical appliances (such as
ice cream makers) inside of refrigerating
appliances.
During Use
•
2
This appliance is designed for domestic use only,
specifically for the storage of edible foodstuffs.
Switch off and unplug the appliance before
carrying out any cleaning or maintenance work.
Servicing
•
This product should be serviced by an authorised
engineer and only genuine spare parts should be
used.
•
Under no circumstances should you attempt to
repair the machine yourself. Repairs carried out
by inexperienced persons may cause injury or
serious malfunctioning. Refer to your local
Service Force Centre and always insist on
genuine spare parts.
At the end of the Appliance
Life
•
When disposing of your appliance, use an
authorised disposal site.
•
Remove the plug and ensure that any locks or
catches are removed, to prevent young children
being trapped inside.
REFRIGERATOR
ZERC 2620
© Electrolux plc 2005
INSTRUCTION BOOKLET
2223 373-11
Download PDF

advertising