INSTALLATION
L.E.D. REAR FENDER TIP W/RUN-BRAKE ACCENT
CUSTOMER SERVICE
PARTS INCLUDED
1
1
1
L.E.D. Black Rear Fender Tip with Smoke Lens
Double “Y” Adapter
Hardware Kit Containing:
2
6mm Spacers
2
M6 Narrow Flat Washers
2
M6 X 1.0 X 25mm Button Socket Cap Screws
4
4” Black Nylon Cable Ties
1
Dielectric Grease Pack
1
Alcohol Pad
1
Installation Instructions
Please read and understand entire instructions before starting installation.
THANK YOU FOR CHOOSING KϋRYAKYN!
IN ORDER TO PROTECT YOU AND OTHERS FROM POSSIBLE INJURY AND/OR
PROPERTY DAMAGE OR LOSS, PLEASE PAY CLOSE ATTENTION TO ALL
INSTRUCTIONS, WARNINGS, CAUTIONS AND NOTICES REGARDING THE USE
AND CARE OF THIS PRODUCT.
THIS INDICATION ALERTS YOU TO THE FACT THAT
IGNORING THE CONTENTS DESCRIBED HEREIN CAN
RESULT IN POTENTIAL DEATH OR SERIOUS INJURY.
This indication alerts you to the fact that ignoring the
contents described herein may negatively affect product
performance and functionality.
IF INSTALLING THIS PRODUCT FOR ANOTHER PARTY,
PLEASE MAKE SURE THEY RECEIVE THIS COPY OF THE
INSTALLATION INSTRUCTIONS SO THEY ARE AWARE OF
THE IMPORTANT INFORMATION CONTAINED IN THEM.
TOOLS SUGGESTED
Set of Metric Hex Wrenches
STRICTLY OBSERVE THE FOLLOWING GUIDELINES IN ORDER TO USE THE
PRODUCT PROPERLY AND AVOID POTENTIALLY DANGEROUS ACCIDENTS.
STEP 1
3248
Read and understand all steps in the instructions before starting the
installation. Park the motorcycle on a hard, level surface and turn off the
ignition.
NOTE: This product requires the motorcycle to be equipped with Kuryakyn
Rear Accessory Plug and Play Harness, P/N 3230, or the applicable
Part Number Küryakyn Rear Plug and Play harness for your model.
NOTE: Pictures shown of Chrome parts. Installation of Black parts will be the
same.
877.370.3604 (toll free)
INSTALLATION QUESTIONS
[email protected]
or call 715.247.2983
LIMITED WARRANTY
Küryakyn warrants that any Küryakyn products
sold hereunder, shall be free of defects in
materials and workmanship for a period of one
(1) year from the date of purchase by the
consumer excepting the following provisions:
● Küryakyn shall have no obligation in the event
the customer is unable to provide a receipt
showing the date the customer purchased the
product(s).
●The product must be properly installed,
maintained and operated under
normal conditions.
●Küryakyn makes no warranty, expressed or
implied, with respect to any gold plated
products.
●Küryakyn shall not be liable for any
consequential and incidental damages, including
labor and paint, resulting from failure of a
Küryakyn product, failure to deliver, delay in
delivery, delivery in nonconforming condition, or
for any breech of contract or duty between
Küryakyn and a customer.
●Küryakyn products are often intended for use in
specific applications. Küryakyn makes no
warranty if a Küryakyn product is used in
applications other than intended.
●Küryakyn electrical products are warranted for
one (1) year from the date of purchase by the
consumer. L.E.D.’S contained in components of
Küryakyn products will be warranted for defects
in materials and workmanship for 3 years from
the date of purchase where as all other
components shall be warranted for one(1) year.
This includes, but is not limited to; control
modules, wiring, chrome & other components.
●Küryakyn makes no warranty of any kind in
regard to other manufacturer¹s products
distributed by Küryakyn. Küryakyn will pass on
all warranties made by the manufacturer and
where possible, will expedite the claim on behalf
of the customer, but ultimately, responsibility for
disposition of the warranty claim lies
with the manufacturer.
ABOUT OUR CATALOG
For purchasing Küryakyn® products, you
can receive a complete catalog free of charge.
Send the Proof-of-Purchase below with
your address to: Küryakyn, P.O. Box 339,
Somerset, WI 54025.
Please indicate either Accessories Catalog for
Harley-Davidson® or GL & Metric Cruisers.
Be sure to ask your local dealer about other
Küryakyn® products, the motorcycle parts and
accessories designed for riders by riders.
©2005 Küryakyn USA® All Rights
reserved.
STEP 2
Thoroughly clean the bottom of the rear fender panel with soapy water and a
clean rag. PIC 1 Rinse and dry completely. Wipe the area with the included
alcohol pad to remove any residue. Dry completely.
3248-21GL-0313
-cont.-
Ensure the area of installation is free of grease, oil, dirt or other
debris including wax/polish products and bugs to ensure proper
adhesion. Küryakyn WILL NOT issue a warranty on any parts lost due
to improper installation.
STEP 3
PIC 1
THOROUGHLY CLEAN THIS AREA
Remove the four fasteners securing the rear fender panel to the motorcycle. Set
these aside, the top two will be reused. PIC 2 Remove the fender panel.
Küryakyn recommends the use of dielectric grease on electrical
connections.
STEP 4
Please refer to the instructions for Rear Plug and Play Harness, P/N 3230,
or applicable Part Number Rear Plug and Play Harness for your model: If
you have an open six pin connector on the Plug and Play Harness (P/N 3230),
apply some of the included dielectric grease and connect the six pin connector
from the Rear Fender Tip to it. If you do not have an open connector, disconnect
one of the six pin sets, apply some of the included dielectric grease to all
connectors and connect the included Double “Y” connector in line. PIC 5 Connect
the existing accessory and the Rear Fender Tip to the new Double “Y” connector.
Use the included cable ties to secure the harness out of harms way.
PIC 2
Secure all wiring away from any moving parts, pinch points or
extreme heat. Küryakyn WILL NOT issue a warranty on any electrical
component that fails due to pinched, crimped, broken, abraded,
melted or frayed wires.
STEP 5
STEP 6
Install the rear fender panel to the motorcycle using the top two fasteners from
Step 3.
Rub the adhesive backing with the back of your fingernail to activate the adhesive.
Remove the backing. Attach the Rear Fender Trim to the bottom of the rear fender
panel by placing one of the included flat washers, then a spacer over the threads
of each of the included M6 button head cap screws. PIC 3 Then, inserting them
through the Rear Fender Trim, thread them into the boss on the motorcycle. PIC 4
Make sure the spacer goes into the recessed hole in the rear fender panel before
tightening the cap screw. Tighten securely, but DO NOT OVER TIGHTEN these.
Press the top of the Trim firmly for one minute to attach the adhesive. Full
bonding will occur in 24 hours.
NOTE: The adhesive tape on the Rear Fender Accent is used as a buffer, it is not
REMOVE THESE FASTENERS
PIC 3
SPACER
M6 BUTTON
CAP SCREW
FLAT WASHER
PIC 4
M6 BUTTON
CAP SCREW
WASHER AND
SPACER
meant to completely secure the Accent to the fender panel.
This Rear Fender Accent will fit with a trailer hitch, but check all
clearances when connecting the trailer to the motorcycle.
STEP 8
Test all lights for proper function.
ENSURE PROPER LIGHT OPERATION BEFORE RIDING THE
MOTORCYCLE. VISIBILITY IS A MAJOR CONCERN FOR
MOTORCYCLISTS. A LIGHT MALFUNCTION COULD RESULT IN
DEATH OR SERIOUS INJURY.
PIC 5
It is the installer’s responsibility to ensure that all of the fasteners
(including pre-assembled) are tightened before operation of the
motorcycle. Küryakyn will not issue a warranty on components lost
due to improper installation. Periodic maintenance may be required.
PAGE
2
Ride On!
L.E.D. REAR FENDER TIP
INSTALLATION
">
