Advertisement
Advertisement
DRAFT 08/04/2014 Instruction Sheet W-Series Hydraulic Torque Wrench • W2000X • W4000X • W8000X • W15000X English (EN) Rev. B L4111 02/2015 Instruction Sheets in Adobe® PDF format Please find the CD or DVD enclosed in the back of this manual The following languages are included: English (EN) Français (FR) Deutsch (DE) Italiano (IT) Español (ES) Nederlands (NL) Português Brasileiro (PT) Svenska (SV) Norsk (NO) Suomi (FI) Pyccкий (RU) ㆰփѝ᮷(ZH) ᰕᵜ䃎 (JA) 한국어 (KO) Note: Download the latest version of Adobe Reader at: http://get.adobe.com/reader 2 Instruction Sheet • W2000X • W4000X • W8000X • W15000X Index 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3 Assembly and Adjustments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 4 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 5 Maintenance and Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 6 Technical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 7 Replacement Parts and Recommended Tools . . . . . . . . . . . . . . . . . . . . . 34 3 ENGLISH W-series Torque Wrenches ENGLISH 1 Introduction Overview The Enerpac W-Series hydraulic torque wrench is designed for controlled tightening and loosening of fasteners in industrial bolting applications. The W-Series features a low profile cassette, compact drive unit and integrated reaction foot, making it ideal for use in locations where workspace is limited. Interchangeable W-Series cassettes are available in a large assortment of both metric and imperial sizes to suit specific customer requirements. An optional TSP300 Pro Series Swivel provides 360 degree X-axis and 160 degree Y-axis rotation, allowing easier positioning of the wrench and hoses in confined areas. The W-Series can be used with a wide range of Enerpac bolting pumps. Electric, air and hand style pumps are available (sold separately). Delivery Instructions Upon delivery all components must be inspected for damage incurred during shipping. If damage is found the carrier should be notified at once. Shipping damage is not covered by the Enerpac warranty. Warranty • Enerpac guarantees the product only for the purpose for which is intended. • All Enerpac products are guaranteed against defects in workmanship and materials for as long as you own them. Any misuse or alteration invalidates the warranty. • Observe all instructions as communicated in this manual. • When replacement parts are needed, use only genuine Enerpac replacement parts. 4 EU Declaration of Incorporation W2000X • W4000X • W8000X • W15000X These tools conform with the requirements for CE Marking. Enerpac declares that the W-Series models listed above meet the applicable standards and directives issued by the European Union. For additional details, refer to the separate EU Declaration of Incorporation. 2 Safety Read all instructions carefully. Follow all recommended safety precautions to avoid personal injury as well as damage to the wrench and/or damage to other property. Enerpac cannot be responsible for any damage or injury from unsafe use, lack of maintenance or incorrect operation. Do not remove warning labels, tags, or decals. In the event any questions or concerns arise, contact Enerpac or a local Enerpac distributor for clarification. If you have never been trained on highpressure hydraulic safety, consult your distributor or service center for a free Enerpac Hydraulic Safety Course. This manual follows a system of safety alert symbols, signal words and safety messages to warn the user of specific hazards. Failure to comply with these warnings could result in death or serious personal injury, as well as damage to the equipment or other property. The Safety Alert Symbol appears throughout this manual. It is used to alert you to potential physical injury hazards. Pay close attention to Safety Alert Symbols and obey all safety messages that follow this symbol to avoid the possibility of death or serious personal injury. DANGER Indicates a hazardous situation that, if not avoided, will result in death or serious personal injury. WARNING Indicates a hazardous situation that, if not avoided, could result in death or serious personal injury. CAUTION Indicates a hazardous situation that, if not avoided, could result in minor or moderate personal injury. NOTICE Indicates information considered important, but not hazard related (e.g. messages relating to property damage). Please note that the Safety Alert Symbol will not be used with this signal word. 2.1 Safety Precautions - W-Series Hydraulic Torque Wrenches WARNING Failure to observe and comply with the following precautions could result in death or serious personal injury. Property damage could also occur. • Always wear protective headwear, ear protectors, footwear and gloves (at a minimum rigger type gloves) suitable for safe operation of the tool. The protective clothing must not interfere with safe operation of the tool or restrict the ability to communicate with coworkers. • Be sure your workplace is safe. Follow the instructions in your workplace's standard operating procedures and be sure to observe all communicated safety precautions. • Do not place any part of the body between the wrench reaction foot and the reaction point. • Do not place any objects between the wrench reaction foot and the reaction point. Keep the hoses away from the reaction points. • Do not stand in the line of movement of the tool when it is in operation. If the tool separates from the nut or bolt during operation it will detach in that direction. • Be aware that a nut or bolt that breaks off during operation of the tool may become a high velocity projectile. • Be sure appropriate guards are securely in position and free from damage. • Keep your hands away from the fastener being loosened or tightened. Tightening and loosening nuts and bolts involves little visible movement. However, the pressures and loads are extreme. • Stop operation immediately if a gap appears between the drive unit locating plate (on the cassette) and the drive unit housing. Have the tool inspected and repaired before it is operated again. • Maximum allowable pressure for the W-Series torque wrench is 10,000 psi [690 bar]. Do not exceed this pressure setting. • Always be sure that pump is stopped and all pressure is fully relieved (0 psi/ bar) before disconnecting or connecting hydraulic hoses. The sudden and uncontrolled release of pressurized oil could occur if hoses are disconnected while under pressure. • Never attempt to connect or disconnect hoses while the pump is on and/or the system is pressurized. • Be certain that all hose couplings are fully connected at both the pump and wrench ends before applying any 5 ENGLISH Safety Alert Symbols are used in conjunction with certain Signal Words that call attention to safety messages or property damage messages and designate a degree or level of hazard seriousness. The Signal Words used in this manual are DANGER, WARNING, CAUTION and NOTICE. ENGLISH hydraulic pressure. If the couplings are not fully connected, oil flow will be blocked, and the drive unit could be subjected to excessive hydraulic pressures. Catastrophic failure of wrench could result. • Never operate the wrench if it is known or suspected that the drive unit retaining pin is worn, bent, missing or damaged. Drive unit could disengage from the cassette and become a dangerous projectile. • Never operate the wrench if the drive unit release handle cannot be fully closed when the drive unit is installed on the cassette. Drive unit could disengage from the cassette and become a dangerous projectile. • Never attempt to force the drive unit onto the cassette if it becomes difficult to install. Have the drive unit and cassette inspected and repaired before placing the wrench back into service. • Never apply more hydraulic pressure to any tool, hose, fitting or accessory than the maximum allowable pressure as stated in the manufacturer’s specifications. The system operating pressure must not exceed the pressure rating of the lowest rated component in the system. • Be sure the operator has completed safety induction training, specific to the work surroundings. The operator should be thoroughly familiar with the controls and the proper use of the tool. • The operator must be of at least the minimum age required by applicable local regulations, laws and the facility standard operating procedures. • Do not abuse or overstress the hoses in any way. Do not bend the hoses excessively. 6 • Take every precaution to prevent oil leaks from occurring. High pressure oil leaks can penetrate the skin, resulting in serious injury. • Never strike the tool while it is pressurized or under load. Components under tension may become dislodged, allowing them to become dangerous projectiles. Uncontrolled release of pressurized hydraulic oil could also occur. • Avoid striking the tool at any time, even when it is not pressurized or under load. Striking the tool could cause permanent damage to wrench components and may affect the wrench calibration. • Use only a high quality nonflammable solvent for cleaning and degreasing parts during wrench repair procedures. To reduce the risk of fire or explosion, do not use flammable solvents. • Be sure to wear proper eye and hand protection when using solvent. Always follow the solvent manufacturer's safety and use instructions and any additional instructions included in the standard operating procedures for your worksite. Be certain there is adequate ventilation when using solvent. CAUTION Failure to observe and comply with the following precautions could result in minor or moderate personal injury. Property damage could also occur. • Always carry the wrench by its housing. Never carry the wrench using the positioning handle. The handle could break and the wrench could drop suddenly. The positioning handle is designed only as an aid to help position the wrench on the bolt or nut. • Be sure that the hex ratchet size corresponds to the size of the fastener being loosened or tightened. Failure to observe this precaution can result in the wrench becoming unstable and can lead to catastrophic failure of the tool. • Always position the wrench for maximum stability. Use the positioning handle to properly position tool during operation. • Be sure reaction points are adequate for the forces at work during operation of the tool. • Be sure the reaction point is of a suitable shape. If possible, use an adjacent nut or bolt as a reaction point. • When the hex ratchet is placed on the nut or bolt a gap may exist between the reaction foot and the reaction point. When the tool is operated the reaction foot and point will make forceful contact. Be sure the wrench is stable before applying hydraulic pressure. • Provide adequate support in vertical and inverted applications. • The torque required to loosen a nut is variable and may exceed the torque capacity of the wrench. Never operate the wrench at above 75 percent of its rated maximum torque when loosening a nut or bolt. • Be sure to minimize torsional and bending stresses in the wrench, the hex ratchet and any accessories. • Bolt lubricants and anti-seize compounds will have a rated coefficient of friction. Be sure to know the coefficient of friction for the lubricant or anti-seize compound that is being used. To ensure proper tightening of nuts and bolts, always use this coefficient of friction when calculating required torque values. NOTICE Failure to observe and comply with the following precautions could result in property damage and/or void the product warranty. • Never carry the wrench by its hoses. • Always use Enerpac pumps and hoses. • Always use Enerpac replacement parts. • The maximum torque output of the wrench must always exceed the torque required to loosen or tighten the nut or bolt. • Never operate the wrench with a hydraulic supply connection to the advance side only as this may damage the internal parts. • In severe service conditions, be aware that the wrench must be inspected, cleaned and lubricated more frequently than normal (see Section 5). • Check that the swivel post capscrews and drive unit cylinder gland are tight prior to use. (see Section 5) • If oil leakage is present from drive unit, replace seals as required (see section 5) before placing the drive unit back into service. • If the wrench is dropped from a significant height, have the tool inspected and checked for proper operation before placing it back into service. • Always follow the inspection and maintenance instructions contained in this manual. Perform maintenance and inspection activities at the specified time intervals. 7 ENGLISH • Be sure that backup wrench (on the opposite end of nut or bolt being tightened or loosened) is secured so it cannot drop or become disengaged during bolting procedures. ENGLISH Use of Torque Wrenches in Explosive Atmospheres In addition to the CE mark, the Enerpac W-Series torque wrenches carry the ATEX mark and classification: • W2000X • W4000X • W8000X • W15000X CE Ex II 2 GD cT4 This classification indicates that the tool is appropriate for use in a potentially explosive atmosphere. The testing standards applicable to the W-Series torque wrenches are the standard EN 13463-1:2009, Non-electrical equipment for use in potentially explosive atmospheres. Part 1: Basic method and requirements, and also the draft standard of ISO/IEC 80079-36. Contact Enerpac if there are any questions regarding the ATEX classification or questions regarding application of the W-Series torque wrenches in hazardous environments. Reducing the Risk of Explosion WARNING Failure to observe and comply with the following precautions and instructions could result in explosion and/or fire. Death and/or serious personal injury could occur. • To help reduce the risk of explosion, be certain to use the W-Series torque wrench only in the specific explosive atmospheres for which it has been tested and certified. Refer to the beginning of this section for ATEX classification information. 8 • The W-Series torque wrench is generally not considered as a potential source of ignition. However, proper operation and maintenance of the tool is essential in order to help ensure that no sparks are generated that could cause an ignition of an explosive gas or dust mixture (which might be present in the environment). Complete operation and maintenance instructions must be provided to all personnel in advance of operating or servicing the wrench. • Hot surfaces can be a major source of ignition. To help prevent the possibility of ignition resulting from excessive surface temperatures, do not use the wrench in an environment with an ambient temperature of above 104°F [40°C] . • Enerpac has designed and constructed the W-Series torque wrench to minimize the possibility of an incendive spark that may be caused by the impact of aluminum components with corroded steel. However, to reduce the chance of an incendive spark, use of the wrench with corroded steel structures or components should be avoided whenever possible. Be especially careful to avoid accidental impacts with the wrench and corroded steel. NOTICE To help prevent a mechanical spark hazard, no components containing a magnesium content greater than 7.5 percent have been used in the W-Series torque wrench (in accordance with standard EN 13463-1). ENGLISH • Take extreme care to prevent the W-Series torque wrench from being dropped on the floor or onto any other metallic surface that might cause mechanical sparks at impact. Also, take every precation to prevent other tools (or other metallic objects) from dropping onto the W-Series torque wrench. Electrostatic Discharge • Electrostatic discharge is a potential source of ignition and can result in electrostatic build-up on isolated conductive parts. Isolated conductive parts create capacitive poles which can become charged. Electrostatic discharge risk is minimized by the hydraulic hoses, which have multiple layers of steel braiding, resulting in electrical continuity between the torque wrench and the grounded hydraulic pump. • Non-conductive polyester labels could be a site for electrostatic build-up. However, electrostatic build-up is prevented by the close proximity of the grounded torque wrench body. 9 ENGLISH 3 Assembly and Adjustments 3.1 Overview and features (Fig. 1 or 2) 1 Hexagon ratchet 2 Cassette 3A Hydraulic Swivel (standard) 3B TSP300 Pro Series Swivel (optional) 4 Advance hose connection 5 Return hose connection 6 Hydraulic drive unit 7 Cassette release lever 8 Reaction foot Fig. 1 3.2 To attach the positioning handle (Fig. 3) • Secure the positioning handle (9) with thumb screw (10). Positioning handle can be installed on either side of wrench or on top of wrench (as needed). 3.3 Changing the Cassette WARNING Be sure that hydraulic pump is OFF and that hydraulic system is depressurized (0 psi/bar) before removing or attaching the cassette. Drive unit could eject under force if this precaution is not followed, resulting in possible personal injury. 3.3.1 To Remove the Cassette (Fig. 4 and 5) Fig. 2 • Be sure the drive unit piston is fully retracted. • Firmly grasp the cassette housing with your hand or place the tool on a workbench. NOTICE Cassette will disengage from drive unit in the following steps. Be sure to support the cassette so that it does not drop. • Pull the cassette release lever (7) outwards. • Remove the hydraulic drive unit (6) from the cassette (2). Fig. 3 10 ENGLISH 3.3.2 To Attach the Cassette (Fig. 4 and 5) • Pull the release lever (7) outwards. • Be sure the retract link (11) aligns with the slot (13) in the ratchet lever. Rotate the piston rod if necessary. • Slide the drive unit onto the cassette and push the spigot (12) through the opening in the drive unit locating plate (14). • Push the release lever (7) back into the cassette (2). Be sure the ball detent clicks into place. Check that cassette release lever is fully closed. CAUTION Do not operate the tool if the cassette release lever is not fully closed. Drive unit could be ejected with great force if lever is not fully closed, Personal injury and/or damage to tool could result. Fig. 4 3.4 To Connect the Hoses (Fig. 6) WARNING Be sure all hoses and fittings are rated for at least 10,000 psi [690 bar] operation. Check that all hydraulic couplings are securely connected before operating the tool. Failure to observe these precautions may result in the hoses bursting or disconnecting under pressure. High pressure oil leakage may also occur. Serious personal injury could result. Fig. 5 The tool is fitted with male and female 1/4 inch NPTF spin-on hydraulic couplings. Use Enerpac twin safety hoses only. Refer to the table below. Enerpac hose model number Description THQ-706T Two hoses, 19.5 feet [6 m] long THQ-712T Two hoses, 39 feet [12 m] long Fig. 6 11 ENGLISH Connect hoses to wrench as described in the following steps: • Be sure that all pressure in system is relieved and that pressure gauge indicates zero (0) psi/bar. • Remove the hose dust caps. • Connect the hose with the female coupling (15) to the wrench advance coupling (4). • Connect the hose with the male coupling (16) to the wrench return coupling (5). • At each connection, pull the collar on the female coupling over the male coupling. Engage threads and hand tighten the collar. • Connect the hoses to the pump. Refer to the pump instruction manual. 4 Operation 4.1 Prior to Operation • Be sure the nut or bolt to be fastened is clean and free of loose dust or dirt. • Be sure the nut threads properly engage with the threads of the bolt, and that cross-threading has not occurred. • Be sure that the threads and the bearing surface are liberally coated with the correct bolt lubricant or anti-seize compound. • Make all torque calculations based on the bolt lubricant's (or anti-seize compound's) stated coefficient of friction. Failure to do so may result in the required bolt load not being achieved. • Be sure that the backup wrench (used to keep the nut or bolt on the opposite end in place) is correctly positioned and secured. WARNING Be certain that backup wrench is of the correct size and that there is an adequate abutment surface. Personal injury could occur if backup wrench loosens or dislodges during bolting procedures. 12 • Contact Enerpac for additional guidance if a suitable reaction point is not available. 4.2 Setting the Torque Adjust the pressure on the pump as necessary to set the torque. Refer to pump manufacturer's instruction manual. 4.3 Wrench Operation WARNING Failure to observe the following precautions could result in serious personal injury: • Stop operation immediately if a gap appears between the drive unit locating plate and the drive unit. A gap in this location indicates that the drive unit retaining pin is worn or damaged, and must be repaired. Use of wrench with worn or damaged retaining pin may result in the drive unit forcefully ejecting from the cassette. • Never strike the tool with a hammer or other object while it is under load. Catastrophic failure of the wrench could occur, and dislodged parts could become dangerous projectiles. Uncontrolled release of hydraulic oil could also occur. Refer to Section 2 of this manual for additional information. 4.3.1 Tightening a Nut or Bolt (Fig. 7 and 8) • Position the tool on the nut or bolt with the clockwise (+) side facing upwards. • Position the reaction foot (17) against a suitable reaction point (18). The reaction point will counteract the force caused by operating the tool. • Start the pump. • Operate the pump until the nut or bolt has been tightened to the required torque. ENGLISH • Stop the pump immediately after work has finished. 4.3.2 Nut and Bolt Loosening Information • Be aware that more torque is usually required to loosen a fastener than to tighten it. • Rusted fasteners (humidity corrosion) may require up to twice the torque required for tightening. • Fasteners that are corroded due to contact with sea water or chemicals will require up to two and a half times the torque required for tightening. • Heat corrosion requires up to three times the torque required for tightening. Fig. 7 WARNING Do not apply more than 75 percent of the wrench’s maximum torque when loosening nuts or bolts. Avoid making sudden start-stop movements (“shock loading”). Failure to observe these precautions may cause a catastrophic failure of the wrench to occur, and wrench components under high tension could become dangerous projectiles. Serious personal injury could result. 4.3.3 Loosening a Nut or Bolt (Fig. 9 and 10) Fig. 8 • Apply penetrating oil to the threads. Allow the oil to soak. • Position the tool on the nut or bolt with the anti-clockwise (-) side facing upwards. • Position the reaction foot (17) against a suitable reaction point (18). The reaction point will counteract the force caused by operating the tool. • Start the pump. • Operate pump until nut (bolt) is loose. If the nut or bolt will be re-used, avoid excess load when loosening. Fig. 9 13 ENGLISH WARNING During loosening, a nut or bolt may be subjected to stresses beyond its material limits, which could result in a permanent reduction of its strength. This reduction could lead to catastrophic failure of the nut, bolt or joint if the fastener is reinstalled. If there is any doubt as to whether the force used during loosening has caused excessive stress, the removed fastener(s) should be discarded and replaced with new fasteners of the proper specifications. 4.3.4 Using an Extended Reaction Arm (Fig. 11) Fig. 10 • Position the WTE Series extended reaction arm (19) against a suitable reaction point. The reaction point will counteract the force caused by operating the tool. • Follow instructions in sections 4.3.1 through 4.3.3. 4.3.5 Using a Reaction Paddle (Fig. 12) • Position the WRP Series reaction paddle (20) against a suitable reaction point. The reaction point will counteract the force caused by operating the tool. • Follow instructions in sections 4.3.1 through 4.3.3. Fig. 11 5 Maintenance and Troubleshooting 5.1 Introduction Preventative maintenance can be performed by the user. Full maintenance must be performed only by an Enerpac authorized service center or a qualified and experienced technician. Fig. 12 14 ◆ A Non destructive testing must be carried out if the tool has been used under severe conditions. ENGLISH Recommended service intervals are: a) 3 months – Heavy Duty use b) 6 months – Normal use c) 12 months – Infrequent use Standard Swivel 5.2 Preventative Maintenance Hydraulic Swivel and Drive Unit (Fig. 13 and 14) ◆ B ◆ • Check tightness of swivel post capscrews and gland (see 5.3). • Pressurize the drive unit to maximum pressure (advance and retract), and check for any signs of leakage. TSP300 Pro Series Swivel ◆ • Any damaged components or seals must be replaced. B • Dry all components and apply a thin coat of molybdenum disulphide grease as indicated (✜). ✤ D C 5.3 Full Maintenance - Hydraulic Swivel and Drive Unit (Fig. 14, 15 and 17) Disassembly: • Remove the circlip (A). • Using a pair of flat blade screwdrivers, gently pry the swivel assembly (B) from the swivel post (F). ✤ E D F H ✤ G ✽ ✽ ✜ ✜ molybdenum disulphide grease Fig. 13 Thread Sealant: ✜ ✤ Silicone Grease ◆ Loctite 577 ✽ Loctite 243 Fig. 14 15 ENGLISH • Remove O-rings (C) from the grooves inside the swivel assembly (B). • Place the swivel assembly in a vise with soft jaws. Remove the hydraulic couplings (B1, B2 and B3) from the swivel assembly (B). Reassembly: NOTICE In the following steps, coat all O-rings and seals with silicone grease before installation. • Install seal (H5) in groove on outside of piston (H6). NOTICE For drive units equipped with the optional TSP300 Pro Series swivel, refer to Enerpac instruction sheet L4119 for additional disassembly instructions. • Install seal (H3) in groove inside drive unit housing (H2). Be sure that “V” side of seal is facing toward the Gland End of housing (H2). • Remove the socket head capscrews (D) and the swivel post (F). Remove O-rings (G) from the swivel post hydraulic ports. NOTICE During reassembly in the following steps, be sure that the piston rod (H1) is inserted through the Spigot End of the housing (H2). • Remove O-ring (E) from the swivel post (F). • Firmly hold the drive unit housing (H2). Using an appropriate pin spanner, unscrew and remove the cylinder gland (H9). Remove O-ring (H8) from the gland. • At the Spigot End of the drive unit, hold the two flat sides of the piston rod (H1) with a spanner wrench. • Remove the piston retaining screw (H7) from the piston (H6). • Remove the piston rod (H1) from the Spigot End of the drive unit housing (H2). • Using a suitable drift, remove the piston (H6) from the Gland End of the drive unit housing (H2). • Remove O-ring (H4) from the groove on inside of piston (H6). • Remove seal (H5) from the groove on outside of piston (H6). • Remove seal (H3) from groove inside drive unit housing (H2). • Clean all exposed components with a mild solvent. • Inspect all parts for damage. • Perform magnetic particle inspection on the following components: - Drive unit housing (H2) - Piston rod (H1) 16 NOTICE Do not use excessive force when installing the piston. This may damage the piston and sealing faces within the drive unit. • Coat the piston rod (H1) with silicone grease and carefully slide it through the Spigot End opening of the housing (H2). • Assemble the piston (H6) on the end of the piston rod (H1). Gently tap the piston (H6) into place against the piston rod (H1). WARNING Be certain that piston retaining screw (H7) is securely tightened in the following step. If screw is not tight, piston rod (H1) could be ejected from drive unit when hydraulic power is applied. Serious personal injury could result. • Apply Loctite 243 thread sealant to the threads of the piston retaining screw (H7) before installation. Tighten piston retaining screw securely. • Install O-ring (H8) in groove on gland (H9). • Screw the gland (H9) into the drive unit housing (H2) by hand, making sure that the O-ring (H8) is not pinched or cut. • Using an appropriate pin spanner, fully tighten the gland (H9). Tap the pin spanner with a suitable mallet to ensure that gland (H9) is tightly installed. ENGLISH Refer to Figs. 14 and 17 for swivel components. (Gland End) H2 ✤ ✽ (Spigot End) ✤ ✤ H1 H7 ✤ H4 H9 H8 H6 H5 H3 ✤ ✤ Silicone Grease Item H3: “V” side of seal must face toward Gland End. ✽ Loctite 243 Thread Sealant Fig. 15 K1 K10K10 ✜ K11 K11 K2 K3 K9 K12 K9 K8 ✜ See Fig. 17 for grease locations. (item K8) K5 ✜ K4 K6 K7 ✜ molybdenum disulphide grease Fig. 16 17 ENGLISH • Tighten the couplings (B1 and B3) and adapter (B2) by hand, until they are each finger tight. Then, wrench tighten these parts an additional 2 to 3 turns beyond finger tight. B1 ◆ B2 B3 ◆ ◆ Loctite 577 B Fig. 17 • Apply a small amount of Loctite 243 thread sealant to the threaded holes in the drive unit. See (✽) in Figure 14 for locations. • Install two O-rings (G) into the ports on the base of the swivel post (F). • Place the swivel post (F) on the drive unit (H), making sure that hydraulic ports are aligned. Be careful that O-rings (G) do not drop out or become pinched or cut. • Install the degreased socket head capscrews (D) and tighten them as follows: a) W2000X and W4000X: (M4 capscrews) – 3.7 Ft.lbs [5.1 Nm] b) W8000X and W15000X: (M5 capscrews) – 7.5 Ft.lbs [10.2 Nm] NOTICE To allow the sealant sufficient time to cure, wait a minimum period of 3 hours at 68 to 104°F [20 to 40°C], or 6 hours at 40 to 68°F [5 to 20°C] before pressurizing the drive unit. • Install a O-ring (E) into the groove on the swivel post (F). • Install O-rings (C) into the grooves inside the swivel assembly (B). • Coat O-rings (E and C) with a small amount of silicone grease. Then, carefully slide the swivel assembly (B) onto the swivel post (F). • Reinstall the circlip retainer ring (A). • Connect hydraulic hoses and cycle the drive unit at 1,000 psi [69 bar] to check for oil leaks. If there are no leaks, cycle the drive unit at 10,000 psi [690 bar] and check again for leaks. WARNING Pressurized hydraulic oil can penetrate the skin and could cause serious personal injury. Always repair any oil leaks before using the wrench. • If the drive unit is equipped with the optional TSP300 Pro Series swivel, refer to Enerpac instruction sheet L4119 for additional reassembly instructions. NOTICE Install the couplings (B1 and B3) and adapter (B2) before installing the swivel (B) on the swivel post (F). Use a vise with soft jaws to hold the swivel as couplings and adapter are installed. • Apply Loctite 577 sealant to threads on female coupling (B3) and adapter (B2). See (◆) in Figure 17 for locations. ✜ ✜ ✜ ✜ molybdenum disulphide grease Fig. 18 18 ✜ ✜ • Remove the screws (K4). Lift and remove the sideplate (K3). • Remove the ratchet lever (K8), hex ratchet (K7), spring loaded drive shoe (K6), and compression spring(s) (K5). The W2000X Series cassettes use one compression spring. The W4000X, W8000X and W15000X Series cassettes use two compression springs. • Clean all exposed components with a mild solvent. • Inspect all parts for damage. • Dry all components. Apply a thin coat of molybdenum disulphide grease as indicated (✜). NOTICE When lubricating the ratchet lever (K8), apply molybdenum disulphide grease (✜) only to the shaded areas shown in Fig. 18. NEVER apply molybdenum disulphide grease (✜) to the ratchet lever bore, or to the drive shoe teeth. Application of grease to these areas will cause erratic operation, slippage of drive mechanism and excessive component wear. • Reverse the disassembly procedure to reassemble the tool. 5.5 Full Maintenance - Cassette (Fig. 16, 18 and 19) • Strip down and clean all exposed components with a mild solvent. • Perform magnetic particle inspection on the following components: - Spacer Retaining Pin (K1) Pin Retainer (K2) Sideplates (K3) Drive Shoe (K6) Ratchet (K7) Ratchet Lever (K8) Drive Unit Retaining Pin (K10) Fail Safe Retaining Pin (K11) Release Lever/Reaction Foot (K12) • Reinstall drive unit retaining pin (K10) and roll pin (K9). WARNING Always reinstall drive unit retaining pin (K10) if removed. Do not operate wrench if retaining pin (K10) is not installed. Failure to reinstall retaining pin (K10) may allow the drive unit to be ejected from the cassette during operation, resulting in possible personal injury. • Check for the correct height for the drive unit retaining pin (K10) and the fail safe retaining pin (K11). See Figure 19, dimensions “X” and “Y”. • Dry all components. Apply a thin coat of molybdenum disulphide grease (✜) as indicated in Figures 16 and 18. Refer to Section 5.4 for additional information about application of molybdenum disulphide grease. • Reverse the disassembly procedure to reassemble the tool. • Drift out the roll pin (K9) holding the drive unit retaining pin (K10) in place. Remove and inspect drive unit retaining pin (K10). Replace if worn or damaged. • Inspect all other parts for damage. 19 ENGLISH 5.4 Preventative Maintenance Cassette (Fig. 16 and 18) • Remove the cassette from the drive unit. ENGLISH Fig. 19 20 Drive Unit Retaining Pin Dimension X Fail Safe Retaining Pin Dimension Y Model (inch) (mm) (inch) (mm) W2000X 0.157 4.00 0.118 3.00 W4000X 0.197 5.00 0.118 3.00 W8000X 0.236 6.00 0.157 4.00 W15000X 0.275 7.00 0.236 6.00 5.6 Troubleshooting ENGLISH 5.6.1 Drive Unit Symptom Cause Drive unit piston Hydraulic coupling is damaged. does not advance or retract. Hydraulic coupling is not connected. Drive unit does not build up pressure. Drive unit leaks. Replace the coupling. Be sure that advance and retract hoses are connected at both pump and wrench. Check that all hose couplings are fully installed. Worn or damaged directional control valve on the hydraulic pump. Take pump to authorized service center. Make repairs as required. Piston seal leaks. Replace the seals. Pump does not build pressure. Adjust the pressure. Pump is defective. Refer to the pump manual. Seal failure. Replace the drive unit seals. Drive unit piston Hose connections are reversed. operates backwards. Gap between drive unit housing and locating plate on cassette. Remedy Drive unit retaining pin is worn, damaged or missing. Reconnect the hoses properly. Replace the drive unit retaining pin. 5.6.2 Cassette Symptom Ratchet returns on retract stroke. Ratchet does not take successive strokes. Cause Broken drive shoe. Remedy Replace the drive shoe. Broken ratchet lever or ratchet. Worn or broken drive shoe. Lubricant on the ratchet and/ or drive shoe splines. Replace ratchet lever and/ or ratchet (as required). Replace the drive shoe. Disassemble the cassette and remove the lubricant from splines. 21 ENGLISH 2 ,J S F E B A J1 D H I G C Fig. 20 6 Technical specifications 6.1 Capacities, Dimensions and Additional Product Data (Fig. 20) Hexagon size range of available cassettes Maximum operating pressure Nominal at 10,000 psi torque at 690 bar Min. torque Weight, Drive Unit Weight, Cassette Dimensions A B C D E F G, H, S I, J1, J2 inch mm psi bar Ft.lbs Nm Ft.lbs Nm lbs kg inch [mm] inch [mm] inch [mm] inch [mm] inch [mm] inch [mm] W2000X W4000X W8000X 1 1/16 - 2 3/8 1 5/16 - 3 3/8 1 7/8 - 4 1/8 30 - 60 36 - 85 50 - 105 10,000 10,000 10,000 690 690 690 2,040 4,175 8,470 2,766 5,661 11,484 204 418 847 277 566 1,148 2.9 4.2 6.8 1.3 1.9 3.1 (See Sections 6.2.1 through 6.2.6) 4.29 [109.0] 5.35 [136.0] 6.77 [172.0] 5.55 [141.0] 6.57 [167.0] 8.07 [205.0] 5.83 [148.0] 7.01 [178.0] 8.19 [208.0] 1.26 [32.0] 1.61 [41.0] 2.07 [52.5] 0.94 [24.0] 1.29 [32.8] 1.65 [41.9] 0.79 [20.0] 0.79 [20.0] 0.98 [25.0] (See Sections 6.2.1 through 6.2.6) (See Sections 6.1.3 and 6.1.4) NOTICE If wall thickness of hexagon reducer insert is less than shown in the table at right, the insert's usable life may be significantly reduced. 22 W15000X 2 7/16 - 4 5/8 65 - 115 10,000 690 15,330 20,785 1,533 2,079 11.0 5.0 8.15 [207.0] 9.45 [240.0] 9.96 [253.0] 2.48 [63.0] 1.97 [50.0] 0.79 [20.0] Minimum Wall Thickness - Hexagon Reducer Insert W2000X Series . . . . . . . . . . . . .0.14 inch [3.50 mm] W4000X Series . . . . . . . . . . . . 0.18 inch [4.69 mm] W8000X Series . . . . . . . . . . . . . 0.24 inch [6.0 mm] W15000X Series . . . . . . . . . . . 0.26 inch [6.69 mm] ENGLISH C1 WTE B1 A1 Fig. 21 6.1.1 Dimensions, WTE Series Extended Reaction Arm (Fig. 21) Wrench Series Reaction Arm Model Dimensions A1 B1 C1 Weight inch [mm] inch [mm] inch [mm] lbs [kg] W2000X WTE20 2.20 [56] 15.67 [398] 2.66 [67.5] 5.73 [2.6] W4000X WTE40 2.59 [66] 17.17 [436] 2.90 [74] 10.14 [4.6] W8000X WTE80 3.35 [85] 17.68 [449] 2.15 [54.5] 16.75 [7.6] W15000X WTE150 4.05 [102] 19.60 [498] 2.80 [72] 26.46 [12.0] (Reaction arm only) 23 ENGLISH C2 WRP B2 L K A2 Fig. 22 6.1.2 Dimensions, WRP Series Reaction Paddle (Fig. 22) Wrench Series Reaction Paddle Model Dimensions A2 B2 C2 K L Weight (Reaction paddle only) 24 inch [mm] inch [mm] inch [mm] inch [mm] inch [mm] lbs [kg] W2000X WRP20 3.31 [84] 5.83 [148] 1.77 [45] 1.40 [35.5] 0.63 [16] 0.88 [0.4] W4000X WRP40 4.29 [109] 7.48 [190] 2.32 [59] 1.87 [47.5] 0.83 [21] 1.76 [0.8] W8000X WRP80 5.37 [136.5] 8.78 [223] 2.72 [69] 2.25 [57] 1.02 [26] 4.41 [2.0] W15000X WRP150 6.50 [165] 10.12 [257] 3.43 [87] 2.74 [69.7] 1.26 [32] 8.60 [3.9] ENGLISH J1 J1 I I Side Mounted Fig. 23 Top Mounted Fig. 24 6.1.3 Dimensions, SWH Series Angled Positioning Handle (Fig. 23 and 24) Wrench Series Handle Model Dimensions I J1 W2000X SWH6A inch [mm] 3.15 [80] inch [mm] 5.04 [128] W4000X SWH6A 3.15 [80] 5.04 [128] W8000X SWH10A 3.62 [92] 5.04 [128] W15000X SWH10A 3.62 [92] 5.04 [128] 25 ENGLISH J2 J2 Side Mounted Fig. 25 Top Mounted Fig. 26 6.1.4 Dimensions, SWH-Series Straight Positioning Handle (Fig. 25 and 26 - optional accessory) Wrench Series Handle Model Dimension J2 26 inch [mm] W2000X SWH6S 4.72 [120] W4000X SWH6S 4.72 [120] W8000X SWH10S 4.72 [120] W15000X SWH10S 4.72 [120] 6.2 Additional Cassette Specifications Drive Unit W2000X W4000X W8000X Cassette Model W2103X W2104X W2107X W2108X W2110X W2113X W2200X W2203X W2206X W4107X W4110X W4113X W4200X W4203X W4206X W4208X W4209X W4212X W4215X W4302X W4085MX W8200X W8203X W8206X W8209X W8212X W8215X W8302X W8085MX W8090MX W8312X W8315X W8402X (S) Hex size mm 30 32 36 38 41 46 50 55 60 36 41 46 50 55 60 63 65 70 75 80 85 50 55 60 65 70 75 80 85 90 95 100 105 (H) mm 31.0 31.0 31.0 33.5 33.5 36.5 39.0 41.8 44.5 37.0 37.0 39.5 41.5 44.0 46.5 49.5 49.5 52.5 55.5 58.5 62.0 45.0 48.0 51.0 52.5 56.0 58.0 60.5 66.0 74.0 74.0 78.0 78.0 (G) mm 53.7 53.7 53.7 58.2 58.2 60.5 63.1 68.6 64.8 61.0 61.0 64.0 66.7 73.4 70.6 76.2 76.2 78.3 81.6 83.5 86.0 78.2 80.0 82.5 85.9 84.8 85.0 89.5 92.2 102.9 102.9 108.0 108.0 Weight kg 2.1 2.1 2.4 2.4 2.4 2.4 2.4 2.5 2.5 3.7 3.7 3.8 3.9 4.6 4.6 4.7 4.7 4.7 4.7 4.8 4.5 8.1 8.1 8.1 9.4 9.3 9.4 9.3 9.8 10.6 10.3 9.3 9.3 27 ENGLISH 6.2.1 Metric System Table - W2000X, W4000X and W8000X Series Cassettes (see Fig. 20 for locations of dimensions S, H and G) ENGLISH 6.2.2 Metric System Table - W15000X Series Cassettes (see Fig. 20 for locations of dimensions S, H and G) Drive Unit W15000X Cassette Model W15209X W15212X W15215X W15302X W15085MX W15090MX W15312X W15315X W15402X W15405X W15115MX (S) Hex size mm 65 70 75 80 85 90 95 100 105 110 115 (H) mm 59.0 59.0 62.0 64.5 69.5 75.0 75.0 80.5 80.5 87.5 87.5 (G) mm 88.6 88.6 90.5 92.9 96.6 101.8 101.8 103.1 103.1 114.8 114.8 Weight kg 13.6 13.6 13.7 14.2 14.9 15.6 15.2 14.8 15.5 15.6 16.1 6.2.3 Imperial System Table - W2000X Series Cassettes (see Fig. 20 for locations of dimensions S, H and G) Drive Unit W2000X 28 Cassette Model W2101X W2102X W2103X W2104X W2105X W2106X W2107X W2108X W2109X W2110X W2111X W2112X W2113X W2114X W2115X W2200X W2201X W2202X W2203X W2204X W2205X W2206X (S) Hex size inch 1 1/16 1 1/8 1 3/16 1 1/4 1 5/16 1 3/8 1 7/16 1 7/16 1 9/16 1 5/8 1 11/16 1 3/4 113/16 1 7/8 1 15/16 2 2 1/16 2 1/8 2 3/16 2 1/4 2 5/16 2 3/8 (H) inch 1.22 1.22 1.22 1.22 1.22 1.22 1.22 1.32 1.32 1.32 1.44 1.44 1.44 1.54 1.54 1.54 1.65 1.65 1.65 1.75 1.75 1.75 (G) inch 2.11 2.11 2.11 2.11 2.11 2.11 2.11 2.29 2.29 2.29 2.38 2.38 2.38 2.48 2.48 2.48 2.70 2.70 2.70 2.55 2.55 2.55 Weight lbs 4.19 4.19 4.19 4.19 4.48 4.43 4.37 4.51 4.44 4.38 4.63 4.57 4.46 4.69 4.64 4.54 4.83 4.74 4.64 4.94 4.84 4.72 Drive Unit W4000X Cassette Model W4105X W4106X W4107X W4108X W4109X W4110X W4111X W4112X W4113X W4114X W4115X W4200X W4201X W4202X W4203X W4204X W4205X W4206X W4207X W4208X W4209X W4210X W4211X W4212X W4213X W4214X W4215X W4300X W4301X W4302X W4303X W4304X W4305X W4306X (S) Hex size inch 1 5/16 1 3/8 1 7/16 1 1/2 1 9/16 1 5/8 1 11/16 1 3/4 1 13/16 1 7/8 1 15/16 2 2 1/16 2 1/8 2 3/16 2 1/4 2 5/16 2 3/8 2 7/16 2 1/2 2 9/16 2 9/16 2 11/16 2 3/4 2 13/16 2 7/8 2 15/16 3 3 1/16 3 1/8 3 3/16 3 1/4 3 5/16 3 3/8 (H) inch 1.46 1.46 1.46 1.46 1.46 1.46 1.56 1.56 1.56 1.63 1.63 1.63 1.73 1.73 1.73 1.83 1.83 1.83 1.95 1.95 1.95 2.07 2.07 2.07 2.18 2.18 2.18 2.30 2.30 2.30 2.44 2.44 2.44 2.44 (G) inch 2.40 2.40 2.40 2.40 2.40 2.40 2.52 2.52 2.52 2.63 2.63 2.63 2.89 2.89 2.89 2.78 2.78 2.78 3.00 3.00 3.00 3.08 3.08 3.08 3.21 3.21 3.21 3.29 3.29 3.29 3.37 3.37 3.37 3.37 Weight lbs 8.15 8.15 8.15 8.31 8.22 8.15 8.43 8.35 8.25 8.45 8.39 8.28 8.65 8.53 8.42 8.73 8.61 8.47 8,96 8.86 8.67 9.14 9.03 8.84 9.32 9.17 8.96 9.51 9.42 9.16 9.92 9.92 9.92 9.92 29 ENGLISH 6.2.4 Imperial System Table - W4000X Series Cassettes (see Fig. 20 for locations of dimensions S, H and G) ENGLISH 6.2.5 Imperial System Table - W8000X Series Cassettes (see Fig. 20 for locations of dimensions S, H and G) Drive Unit W8000X 30 Cassette Model W8114X W8115X W8200X W8201X W8202X W8203X W8204X W8205X W8206X W8207X W8208X W8209X W8210X W8211X W8212X W8213X W8214X W8215X W8300X W8301X W8302X W8303X W8304X W8305X W8306X W8307IX W8308X W8309X W8310X W8311X W8312X W8313X W8314X W8315X W8400X W8401IX W8402X (S) Hex size inch 1 7/8 1 15/16 2 2 1/16 2 1/8 2 3/16 2 1/4 2 5/16 2 3/8 2 7/16 2 1/2 2 9/16 2 5/8 2 11/16 2 3/4 2 13/16 2 7/8 2 15/16 3 3 1/16 3 1/8 3 3/16 3 1/4 3 5/16 3 3/8 3 7/16 3 1/2 3 9/16 3 5/8 3 11/16 3 3/4 3 13/16 3 7/8 3 15/16 4 4 1/16 4 1/8 (H) inch 1.77 1.77 1.77 1.89 1.89 1.89 2.01 2.01 2.01 2.07 2.07 2.07 2.20 2.20 2.20 2.28 2.28 2.28 2.38 2.38 2.38 2.60 2.60 2.60 2.60 2.60 2.60 2.91 2.91 2.91 2.91 2.91 2.91 3.07 3.07 3.07 3.07 (G) inch 3.08 3.08 3.08 3.15 3.15 3.15 3.25 3.25 3.25 3.38 3.38 3.38 3.34 3.34 3.34 3.35 3.35 3.35 3.52 3.52 3.52 3.63 3.63 3.63 3.63 3.63 3.63 4.05 4.05 4.05 4.05 4.05 4.05 4.25 4.25 4.25 4.25 Weight lbs 17.97 17.89 17.75 17.52 17.36 17.22 17.92 17.76 17.59 17.65 17.52 17.29 17.50 17.36 17.12 17.57 17.38 17.11 17.77 17.65 17.33 18.99 18.72 18.54 18.36 18.11 17.81 20.36 20.18 19.93 19.71 19.46 19.10 20.31 20.04 19.80 19.39 Drive Unit W15000X Cassette Model W15207X W15208X W15209X W15210X W15211X W15212X W15213X W15214X W15215X W15300X W15301X W15302X W15303X W15304X W15305X W15306X W15307IX W15308X W15309X W15310X W15311X W15312X W15313X W15314X W15315X W15400X W15401IX W15402X W15403IX W15404X W15405X W15406X W15407X W15408IX W15409IX W15410IX (S) Hex size inch 2 7/16 2 1/2 2 9/16 2 5/8 2 11/16 2 3/4 2 13/16 2 7/8 2 15/16 3 3 1/16 3 1/8 3 3/16 3 3/16 3 5/16 3 3/8 3 7/16 3 1/2 3 3/16 3 5/8 3 11/16 3 3/4 3 13/16 3 7/8 3 15/16 4 4 1/16 4 1/8 4 3/16 4 1/4 4 5/16 4 3/8 4 7/16 4 1/2 4 9/16 4 5/8 (H) inch 2.32 2.32 2.32 2.32 2.32 2.32 2.44 2.44 2.44 2.54 2.54 2.54 2.74 2.74 2.74 2.74 2.74 2.74 2.95 2.95 2.95 2.95 2.95 2.95 3.17 3.17 3.17 3.17 3.17 3.17 3.44 3.44 3.44 3.44 3.44 3.44 (G) inch 3.49 3.49 3.49 3.49 3.49 3.49 3.56 3.56 3.56 3.66 3.66 3.66 3.80 3.80 3.80 3.80 3.80 3.80 4.01 4.01 4.01 4.01 4.01 4.01 4.06 4.06 4.06 4.06 4.06 4.06 4.52 4.52 4.52 4.52 4.52 4.52 Weight lbs 30.72 30.72 30.72 30.72 30.72 30.72 30.62 30.39 30.08 30.86 30.71 30.34 32.38 32.07 31.85 31.63 31.32 30.98 31.70 31.70 31.70 31.70 31.70 31.70 34.02 33.70 33.41 33.09 32.81 32.39 35.61 35.32 34.99 34.63 34.28 33.72 31 ENGLISH 6.2.6 Imperial System Table - W15000X Series Cassettes (see Fig. 20 for locations of dimensions S, H and G) ENGLISH 6.3 Torque Settings 6.3.1 Metric System Torque Factor Calculation To set the torque, adjust the pump pressure according to the following calculation: Pump pressure (bar) = Torque (Nm) / Torque factor Torque factor Metric system: W2000X W4000X W8000X W15000X 4.0085 8.2037 16.6432 30.1227 W8000X Torque (Nm) 999 1,498 1,997 2,496 2,996 3,495 3,994 4,494 4,993 5,492 5,992 6,491 6,990 7,489 7,989 8,488 8,987 9,487 9,986 10,485 10,984 11,484 W15000X Torque (Nm) 1,807 2,711 3,615 4,518 5,422 6,326 7,229 8,133 9,037 9,941 10,844 11,748 12,652 13,555 14,459 15,363 16,266 17,170 18,074 18,977 19,881 20,785 6.3.2 Metric System Pressure/Torque Table Pump Pressure (bar) 60 90 120 150 180 210 240 270 300 330 360 390 420 450 480 510 540 570 600 630 660 690 NOTICE 32 W2000X Torque (Nm) 241 361 481 601 722 842 962 1,082 1,203 1,323 1,443 1,563 1,684 1,804 1,924 2,044 2,165 2,285 2,405 2,525 2,646 2,766 W4000X Torque (Nm) 492 738 984 1,231 1,477 1,723 1,969 2,215 2,461 2,707 2,953 3,199 3,446 3,692 3,938 4,184 4,430 4,676 4,922 5,168 5,414 5,661 Torque values are rounded to the nearest whole unit. ENGLISH 6.3.3 Imperial System Torque Factor Calculation To set the torque, adjust the pump pressure according to the following calculation: Pump pressure (psi) = Torque (Ft.lbs) / Torque factor Torque factor Imperial system: W2000X W4000X W8000X W15000X 0.204 0.4175 0.847 1.533 W8000X Torque (Ft.lbs) 847 1,271 1,694 2,118 2,541 2,965 3,388 3,812 4,235 4,659 5,082 5,506 5,929 6,353 6,776 7,200 7,623 8,047 8,470 W15000X Torque (Ft.lbs) 1,533 2,300 3,066 3,833 4,599 5,366 6,132 6,899 7,665 8,432 9,198 9,965 10,731 11,498 12,264 13,031 13,797 14,564 15,330 6.3.4 Imperial System Pressure/Torque Table Pump Pressure (psi) 1,000 1,500 2,000 2,500 3,000 3,500 4,000 4,500 5,000 5,500 6,000 6,500 7,000 7,500 8,000 8,500 9,000 9,500 10,000 NOTICE W2000X Torque (Ft.lbs) 204 306 408 510 612 714 816 918 1,020 1,122 1,224 1,326 1,428 1,530 1,632 1,734 1,836 1,938 2,040 W4000X Torque (Ft.lbs) 418 626 835 1,044 1,253 1,461 1,670 1,879 2,088 2,296 2,505 2,714 2,923 3,131 3,340 3,549 3,758 3,966 4,175 Torque values are rounded to the nearest whole unit 33 ENGLISH 7 Replacement parts and recommended tools 7.1 Ordering Replacement Parts For replacement parts information, refer to the Enerpac repair parts sheet for your wrench model. Repair parts sheets are available on the internet at www.enerpac. com. Have the following information ready when ordering replacement parts: • Wrench model and serial numbers (for both drive unit and cassette). • Approximate date of purchase. • Part number and description of each part being ordered. 7.2 Recommended Tool Kit, W2000X Series – – – – – – – – – – – 7/8" A/F Spanner 3/4" A/F Spanner 5/8" A/F spanner Circlip Pliers Seal Extraction Tool 16 mm A/F Spanner ø 4 mm x 5 mm LG x 20 mm PCD Pin Spanner 5 mm A/F Allen Key 3 mm A/F Allen Key 2.5 mm A/F Allen Key 3 mm Terminal Screwdriver 7.3 Recommended Tool Kit, W4000X Series – – – – – – 34 7/8" A/F Spanner 3/4" A/F Spanner 5/8" A/F Spanner Circlip Pliers Seal Extraction Tool ø 4 mm x 5 mm LG x 25 mm PCD Pin Spanner – – – – 6 mm A/F Allen Key 4 mm A/F Allen Key 2.5 mm A/F Allen Key 3 mm Terminal Screwdriver 7.4 Recommended Tool Kit, W8000X Series – – – – – – – – – – – – 7/8" A/F Spanner 3/4" A/F Spanner 5/8" A/F Spanner Circlip Pliers Seal Extraction Tool 1 1/8" A/F Spanner ø 4 mm x 5 mm LG x 30 mm PCD Pin Spanner 10 mm Allen Key 5 mm A/F Allen Key 4 mm A/F Allen Key 2.5 mm A/F Allen Key 3 mm Terminal Screwdriver 7.5 Recommended Tool Kit, W15000X Series – – – – – – – – – – – – 7/8" A/F Spanner 3/4" A/F Spanner 5/8" A/F Spanner Circlip Pliers Seal Extraction Tool 1 3/8" A/F Spanner ø 4 mm x 5 mm LG x 40 mm PCD Pin Spanner 10 mm A/F Allen Key 6 mm A/F Allen Key 4 mm A/F Allen Key 2.5 mm A/F Allen Key 3 mm Terminal Screwdriver Notes: A/F = Across Flats PCD = Pitch Circle Diameter Please contact Enerpac if the disc is not included. Or, visit www.enerpac.com for a download of the manual. Instruction Sheets W-Series Hydraulic Torque Wrenches W2000X, W4000X W8000X & W15000X 35 Enerpac Worldwide Locations Australia and New Zealand Actuant Australia Ltd. Block V Unit 3 Regents Park Estate 391 Park Road Regents Park NSW 2143 (P.O. Box 261) Australia T +61 (0)2 9743 8988 F +61 (0)2 9743 8648 [email protected] Brazil Power Packer do Brasil Ltda. Rua Luiz Lawrie Reid, 548 09930-760 - Diadema (SP) - Brazil T +55 11 5687 2211 Toll Free: 0800 891 5770 [email protected] China (Taicang) Actuant (China) Industries Co. Ltd. No. 6 Nanjing East Road, Taicang Economic Dep Zone Jiangsu, China T +86 0512 5328 7500 F +86 0512 5335 9690 Toll Free: +86 400 885 0369 [email protected] France, Switzerland, North Africa and French speaking African countries ENERPAC Une division d’ACTUANT France S.A.S. ZA de Courtaboeuf 32, avenue de la Baltique 91140 VILLEBON /YVETTE France T +33 1 60 13 68 68 F +33 1 69 20 37 50 [email protected] Germany and Austria ENERPAC GmbH P.O. Box 300113 D-40401 Düsseldorf Willstätterstrasse 13 D-40549 Düsseldorf, Germany T +49 211 471 490 F +49 211 471 49 28 [email protected] India ENERPAC Hydraulics (India) Pvt. Ltd. No. 10, Bellary Road, Sadashivanagar, Bangalore, Karnataka 560 080 India T +91 80 3928 9000 [email protected] www.enerpac.com Italy ENERPAC S.p.A. Via Canova 4 20094 Corsico (Milano) T +39 02 4861 111 F +39 02 4860 1288 [email protected] e-mail: [email protected] Japan Applied Power Japan LTD KK Besshocho 85-7 Kita-ku, Saitama-shi 331-0821, Japan T +81 48 662 4911 F +81 48 662 4955 [email protected] Middle East, Egypt and Libya ENERPAC Middle East FZE Office 423, LOB 15 P.O. Box 18004, Jebel Ali, Dubai United Arab Emirates T +971 (0)4 8872686 F +971 (0)4 8872687 [email protected] Russia Rep. office Enerpac Russian Federation Admirala Makarova Street 8 125212 Moscow, Russia T +7 495 98090 91 F +7 495 98090 92 [email protected] Southeast Asia, Hong Kong and Taiwan Actuant Asia Pte Ltd. 83 Joo Koon Circle Singapore 629109 T +65 68 63 0611 F +65 64 84 5669 Toll Free: +1800 363 7722 [email protected] South Korea Actuant Korea Ltd. 3Ba 717, Shihwa Industrial Complex Jungwang-Dong, Shihung-Shi, Kyunggi-Do Republic of Korea 429-450 T +82 31 434 4506 F +82 31 434 4507 [email protected] Spain and Portugal ENERPAC SPAIN, S.L. Avda. Los Frailes, 40 – Nave C & D Pol. Ind. Los Frailes 28814 Daganzo de Arriba (Madrid) Spain T +34 91 884 86 06 F +34 91 884 86 11 [email protected] Sweden, Denmark, Norway, Finland and Iceland Enerpac Scandinavia AB Kopparlundsvägen 14, 721 30 Västerås Sweden T +46 (0) 771 41 50 00 [email protected] internet: www.enerpac.com The Netherlands, Belgium, Luxembourg, Central and Eastern Europe, Baltic States, Greece, Turkey and CIS countries ENERPAC B.V. Galvanistraat 115, 6716 AE Ede P.O. Box 8097, 6710 AB Ede The Netherlands T +31 318 535 911 F +31 318 535 848 [email protected] Enerpac Integrated Solutions B.V. Opaalstraat 44, 7554 TS Hengelo P.O. Box 421, 7550 AK Hengelo The Netherlands T +31 74 242 20 45 F +31 74 243 03 38 [email protected] South Africa and other English speaking African countries Enerpac Africa Pty Ltd. No. 5 Bauhinia Avenue Cambridge Office Park Block E Highveld Techno Park Centurion 0157 Republic of South Africa T: +27 12 940 0656 [email protected] United Kingdom and Ireland ENERPAC UK Ltd. 5 Coopies Field Morpeth, Northumberland NE61 6JR, England T +44 (0) 1670 5016 50 F +44 (0) 1670 5016 51 [email protected] USA, Latin America and Caribbean ENERPAC World Headquarters P.O. Box 3241 Milwaukee WI 53201-3241 USA N86 W12500 Westbrook Crossing Menomonee Falls, Wisconsin 53051 T +1 262 293 1600 F +1 262 293 7036 User inquiries: T +1 800 433 2766 Distributor inquiries/orders: T +1 800 558 0530 F +1 800 628 0490 Technical inquiries: [email protected] [email protected] All Enerpac products are guaranteed against defects in workmanship and materials for as long as you own them. For the location of your nearest authorized Enerpac Service Center, visit us at www.enerpac.com 011415 © Enerpac 2015 Subject to change without notice. ">

Public link updated
The public link to your chat has been updated.
Advertisement