Quasar VV-1330 Operating instructions

Quasar VV-1330 Operating instructions
Basic Operation
ModelsNo. VV-1301/VV-1311W/VV-13F1/VV-2001
Initial Setup
Combination VCR
Operating Instructions
TV Operation
• SELF-DEMO Procedure is on page 4.
As an ENERGY STAR® Partner,
Matsushita Electric Corporation of America has
determined that this product or product model meets
the ENERGY STAR® guidelines for energy efficiency.
Please read these instructions carefully before attempting to connect,
operate, or adjust this product. Please save this manual.
Spanish Quick Use Guide is included.
(Guía para rápida consulta en español está incluida.)
LSQT0502A
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
VV13F1 P01-11 Initial Setup.p65
1
01/09/19, 10:37
Timer Operation Advanced Operation For Your Information
• Initial Setup and Connection Procedures are on pages 8 to 13.
Important Safeguards and Precautions
READ AND RETAIN ALL SAFETY AND
OPERATING INSTRUCTIONS. HEED ALL
WARNINGS INTHE MANUAL AND ON UNIT
INSTALLATION
An outside antenna or cable system must be properly
grounded to provide some protection
against built up static charges
and voltage. Section 810 of
the National Electrical Code,
ANSI/NFPA 70 (in Canada,
part 1 of the Canadian
Electrical Code) provides
information regarding proper
grounding of the mast and supporting structure, grounding
of the lead-in wire to an antenna discharge unit, size of
grounding conductors, location of antenna discharge unit,
connection to grounding electrodes, and requirements for
the grounding electrode.
NEC - NATIONAL
ELECTRICAL CODE
1 POWER SOURCE CAUTION
GROUND
CLAMP
Operate only from power source indicated on unit
or in this manual. If uncertain, have your Electric
Utility Service Company or Video Products Dealer
verify your home power source.
2 POWER CORD PLUG
For safety, this unit has a polarized type plug (one
wide blade), or a three-wire grounding type plug.
Always hold the plug firmly and make sure your
hands are dry when plugging in or unplugging the
AC power cord. Regularly remove dust, dirt, etc.
on the plug.
POLARIZED PLUG CAUTION:
The plug fits into outlet one way. If it cannot be fully
inserted, try reversing it. If it still will not fit, have an
electrician install the proper wall outlet. Do not
tamper with the plug.
GROUNDING PLUG CAUTION:
The plug requires a three-hole grounding outlet.
If necessary, have an electrician install the proper
outlet. Do not tamper with the plug.
3 POWER CORD
To avoid unit malfunction, and to protect against
electrical shock, fire or personal injury:
-Keep power cord away from heating appliances
and walking traffic. Do not rest heavy objects on,
or roll such objects over the power cord.
-Do not tamper with the cord in any way.
-An extension cord should have the same type
plug (polarized or grounding) and must be
securely connected.
-Overloaded wall outlets or extension cords is a
fire hazard.
-Frayed cords, damaged plugs, and damaged or
cracked wire insulation are hazardous and
should be replaced by a qualified electrician.
4 DO NOT BLOCK VENTILATION HOLES
Ventilation openings in the cabinet release heat
generated during operation. If blocked, heat
build-up may result in a fire hazard or heat
damage to cassettes.
For your protection:
a. Never cover ventilation slots while unit is ON,
or operate unit while placed on a bed, sofa,
rug, or other soft surface.
b. Avoid built-in installation, such as a book case
or rack, unless properly ventilated.
5 AVOID EXTREMELY HOT LOCATIONS OR
SUDDEN TEMPERATURE CHANGES
Do not place unit over or near a heater or
regulator, in direct sunlight, etc. If unit is suddenly
moved from a cold place to a warm place,
moisture may condense in unit and on the tape
causing damage.
6 TO AVOID PERSONAL INJURY
• Never place unit on support or
stand that is not firm, level,
and adequately strong.
The unit could fall causing
serious injury to a child or
adult and damage to the unit.
• Move any appliance and cart
combination with care. Quick
stops, excessive force, and uneven
surfaces may cause objects to overturn.
• Carefully follow all operating instructions.
2
OUTDOOR ANTENNA INSTALLATION
1 SAFE ANTENNA AND CABLE CONNECTION
ELECTRIC
SERVICE
EQUIPMENT
ANTENNA LEAD
IN WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
GROUNDING
CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE
GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
2 KEEP ANTENNA CLEAR OF HIGH VOLTAGE
POWER LINES OR CIRCUITS
Locate an outside antenna system well away from power
lines and electric light or power circuits so it will never touch
these power sources should it ever fall. When installing
antenna, absolutely never touch power lines, circuits or
other power sources as this could be fatal.
USING THE UNIT
Before unit is brought out of storage or moved to a new location,
refer again to the INSTALLATION section of these safeguards.
1 KEEP UNIT WELL AWAY FROM WATER OR
MOISTURE, such as vases, sinks, tubs, etc.
2 IF EXPOSED TO RAIN, MOISTURE, OR STRONG
IMPACT, unplug unit and have it inspected by a qualified
service technician before use.
3 ELECTRICAL STORMS
During a lightning storm, or before leaving unit unused for
extended periods of time, disconnect all equipment from the
power source as well as the antenna and cable system.
4 WHEN UNIT IS PLUGGED IN
• DO NOT OPERATE IF:
- liquid has spilled into unit.
- unit was dropped or otherwise damaged.
- unit emits smoke, malodors, or noises.
Immediately unplug unit, and have it inspected by a service
technician to avoid potential fire and shock hazards.
• Never drop or push any object through openings in unit.
Touching internal parts may cause electric shock or fire hazard.
• Keep magnetic objects, such as speakers, away from unit
to avoid electrical interference.
5 USING ACCESSORIES
Use only accessories recommended by the manufacturer to
avoid risk of fire, shock, or other hazards.
6 CLEANING UNIT
Unplug unit. Use a clean, dry, chemically untreated cloth to gently
remove dust or debris. DO NOT USE cleaning fluids, aerosols, or
forced air that could over-spray, or seep into unit and cause
electrical shock. Any substance, such as wax, adhesive tape, etc.
may mar the cabinet surface. Exposure to greasy, humid, or dusty
areas may adversely affect internal parts.
SERVICE
1 DO NOT SERVICE PRODUCT YOURSELF
If, after carefully following detailed operating instructions, the
unit does not operate properly, do not attempt to open or
remove covers, or make any adjustments not described in the
manual. Unplug unit and contact a qualified service technician.
2 REPLACEMENT OF PARTS
Make sure the service technician uses only parts specified
by the manufacturer, or have equal safety characteristics as
original parts. The use of unauthorized substitutes may
result in fire, electric shock, or other hazards.
3 SAFETY CHECK AFTER SERVICING
After unit is serviced or repaired, request that a through safety
check be done as described in the manufacturer’s service
literature to insure video unit is in safe operating condition.
Forassistance,pleasecall:1-800-211-PANA(7262)orsende-mailto:[email protected]
VV13F1 P01-11 Initial Setup.p65
2
01/09/19, 10:37
Safety Precautions/Mesures de sécurité
Warning : To prevent fire or shock hazard, do not expose this equipment to rain or moisture.
Caution : To prevent electric shock, match wide blade of plug to wide slot, fully insert.
Avertissement :Afin de prévenir tout risque d’incendie ou de chocs électriques, ne
pas exposer cet appareil à la pluie ou à une humidité excessive.
Attention : Pour éviter les chocs électriques, introduire la lame la plus large de la fiche
dans la borne correspondante de la prise et pousser jusqu’au fond.
This video recorder, equipped with the HQ (High Quality) System, is compatible
with existing VHS equipment.
mark. It is recommended that only cassette
Only use those tapes with the
tapes that have been tested and inspected for use in 2, 4, 6, and 8 hour VCR
machines be used.
This television receiver provides display of television closed captioning in
accordance with §15.119 of the FCC rules.
FCC WARNING : Any unauthorized changes or modifications to this
equipment would void the user’s authority to operate.
This symbol warns the user that uninsulated
voltage within the unit may have sufficient
magnitude to cause electric shock. Therefore,
it is dangerous to make any kind of contact
with any inside part of this unit.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK
OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS
INSIDE REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL
This symbol alerts the user that important
literature concerning the operation and
maintenance of this unit has been included.
Therefore, it should be read carefully in order
to avoid any problems.
3
VV13F1 P01-11 Initial Setup.p65
3
01/09/19, 10:37
Before Using
Congratulations
Loading the Batteries
on your purchase of one of the most sophisticated
and reliable products on the market today. Used
properly, it will bring you and your family years of
enjoyment. Please fill in the information below. The
serial number is on the tag located on the back of
your unit.
Date of Purchase
Dealer Purchased From
Dealer Address
Dealer Phone No.
Model No.
Serial No.
1) Open the
cover.
2) Insert batteries as marked.
Accessories
Remote Control
LSSQ0283
(VV-1301/VV-13F1/
VV-2001)
LSSQ0284
(VV-1311W)
3) Close the cover.
Battery replacement caution
• Do not mix old and new batteries.
• Do not mix alkaline with manganese batteries.
Batteries
2 “AA”
Prevent Accidental Tape Erasure
Break off the tab to protect.
To order accessories,
call toll free 1-800-332-5368.
SELF-DEMO Mode
With Power ON, press
PLAY/REPEAT on the
unit for 7 seconds to
deactivate the SELFDEMO Mode.
Repeat this to display
demo screen.
4
Record Tab
Screw driver
To record again.
Cover the hole
with cellophane tape.
Forassistance,pleasecall:1-800-211-PANA(7262)orsende-mailto:[email protected]
VV13F1 P01-11 Initial Setup.p65
4
01/09/19, 10:37
Table of Contents
Initial Setup
Important Safeguards and Precautions / Safety Precautions ........ 2
Before Using......................................................................................... 4
Table of Contents ................................................................................ 5
Location of Controls ............................................................................ 6
Initial Setup for ANT. / Cable Connection ......................................... 8
Initial Setup for DSS / Cable box Connection .................................. 10
Basic Operation
Reset Language, Channels, Clock, Time Zone Adjust ................... 12
Playback a Tape .................................................................................. 14
Record On a Tape ............................................................................... 14
Copy Your Tapes (Dubbing) .............................................................. 15
TV Operation
TV Operation ....................................................................................... 16
Picture Adjustment ............................................................................. 17
TV Timer Features .............................................................................. 18
Closed Caption System ...................................................................... 20
Tape Operation.................................................................................... 24
Special VCR Features ........................................................................ 27
V-Chip Control Feature ...................................................................... 30
On-Screen Display (OSD) .................................................................. 33
Unit Information .................................................................................. 34
Before Requesting Service ................................................................ 35
Service Center List ............................................................................. 36
Limited Warranty ................................................................................ 37
Spanish Quick Use Guide / Guía para rápida consulta .................. 38
Index ..................................................................................................... BC
5
VV13F1 P01-11 Initial Setup.p65
5
01/09/19, 10:37
Timer Operation Advanced Operation For Your Information
Timer Recording ................................................................................. 22
Location of Controls
Remote Control Buttons
EJECT button:
When EJECT is pressed, the tape is ejected from Cassette Compartment.
If EJECT is pressed during recording, the unit will not respond to the command.
EJECT
Page 14.
NITE
Page 16.
POWER
Page 8.
SLEEP
Page 19.
TRACKING UP/DOWN
Page 34.
DISPLAY
Page 33.
TAPE POSITION
Page 25.
NUMBER keys
Page 16.
ADD/DELETE
Page 13.
COUNTER RESET
Page 26.
RAPID TUNE
Page 16.
SEARCH
Page 24.
MUTE
Page 16.
VOLUME UP/DOWN
Page 16.
SET/BACKSPACE
Page 13.
CHANNEL UP/DOWN
Page 16.
SET/BACKSPACE
Page 13.
PROGRAM
Page 22.
ACTION
Page 12.
FAST FORWARD/SEARCH
Page 14.
STOP
Page 14.
PLAY
Page 14.
REC
Page 14.
CM/ZERO
Page 26.
REWIND/SEARCH
Page 14.
SPEED
Page 14.
PAUSE/SLOW
Page 14.
6
Forassistance,pleasecall:1-800-211-PANA(7262)orsende-mailto:[email protected]
VV13F1 P01-11 Initial Setup.p65
6
01/09/19, 10:37
Initial Setup
Front View of the unit and Indicators on the Front Panel
<Model VV-2001 unit shown>
REWIND/SEARCH Page 14
ACTION
Page 13
STOP/EJECT
ACTION
Cassette Compartment Page 14
Page 14
Page 13
PLAY/REPEAT
Page 14
FAST FORWARD/
SEARCH
Page 14
CHANNEL UP/DOWN Page 16
TRACKING UP/DOWN Page 34
SELECT UP/DOWN
Page 13
REC
Page 14
VOLUME UP/DOWNPage 16
SET/BACK SPACE
Page 13
TIMER
Page 19
POWER
Buit-In Speaker
Page 8
POWER
VOL
CH
STOP/EJECT REW/
PLAY/REPEAT FF/
REC
Phones Jack
TIMER
REC ON TIMER PROG TIMER
ACTION
VIDEO IN
Audio/Video In Jack Page 15
PROG TIMER Indicator
REC ON TIMER PROG TIMER
Lights when the unit is set for
Timer Recording. It flashes
when a Timer Recording has
been set with no tape inserted,
the clock is not set, or the tape
is in motion.
Page 22
REC Indicator
VIDEO IN
VIDEO IN
AUDIO IN
AUDIO IN
<Models VV-1301/
VV-1311W/VV-13F1>
Page 16
AUDIO IN
Lights during recording.
In Rec Pause or OTR
Pause mode, the
indicator flashes.
Page 14
Remote Sensor
ON TIMER Indicator
Lights when the On Timer
is set.
Page 18
Rear View of the unit
<Models VV-1301/VV-1311W/VV-13F1 unit shown>
Easy-Grip-Handle
<Models VV-1301/VV-1311W/
VV-13F1>
Use when transporting
the unit.
AC Power Plug
When plugged into
an AC outlet, the unit
consumes 4.0 W of
electric power in OFF
condition.
VHF/UHF
VHF/UHF Antenna
Input Terminal
In from your Antenna
or Cable.
Pages 8, 10
7
VV13F1 P01-11 Initial Setup.p65
7
01/09/19, 10:37
1
Initial Setup
Manual Clock Set
Reset all unit Memory Functions
If AUTO CLOCK SET was incomplete, manually
set the clock as follows.
Press ACTION on the Remote to
display SET CLOCK Menu screen.
When moving unit to a new location, or if a
mistake was made in the Initial Setup section.
• Make sure a tape is not inserted in the unit.
<Model VV-2001 unit shown>
SET CLOCK
:
1/ /
DST : ON
SELE CT MONTH
SE
SELECT :
SET
:
END
: ACT I ON
POWER
VOL
CH
STOP/EJECT REW/
PLAY/REPEAT FF/
REC
TIMER
REC ON TIMER PROG TIMER
ACTION
VIDEO IN
2
to select the month
Press
and press to set. In the same
manner, select and set the date,
year, time, and DST. (Daylight
Saving Time)
SET CLOCK
2 / 7/2001 WED 12: 00PM
DST : ON
SELE CT COMPLETED
SE
SET
END
3
:
: ACT I ON
AUDIO IN
the unit
1 Turn
Power on.
and hold both PLAY and
2 Press
FF on the unit for more than 5
seconds.
• The power will shut off.
• Please ignore “NO CASSETTE”
warning.
3 Do “Initial Setup” on page 8.
Press ACTION twice to start
CLOCK and exit.
POWER
SELECT/SET
:CH UP
:CH DOWN
:VOL UP
:VOL DOWN
ACTION
9
VV13F1 P01-11 Initial Setup.p65
9
01/09/19, 10:37
Press CH to start
CHANNEL /CLOCK AUTO
SET operation. Settings are
performed automatically.
If the setup is completed, the
following screen is displayed.
Initial Setup
4
2 / 7 / 2001 WEDDST
12 :: ON
00PM
SETT I NG : CH 1 0
AUTO CLOCK SET
COMPLETED
POWER
END : PRESS CH UP KEY
If AUTO CLOCK SET IS
INCOMPLETE screen appears,
set the clock using MANUAL
CLOCK SET procedure on page 9.
SET CLOCK
2 / 7/2001 WED 12: 00
00PM
PM
SELECT/SET
:CH UP
:CH DOWN
:VOL UP
:VOL DOWN
ACTION
DST : ON
SELE CT COMPLETED
SET
END
:
: ACT I ON
Note to CABLE System Installer
This reminder is provided to call the CABLE (Cable TV) System Installers attention to
Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular,
specifies that the cable ground shall be connected to the grounding system of the
building, as close to the point of cable entry as practical.
11
VV13F1 P01-11 Initial Setup.p65
11
01/09/19, 10:37
Reset Language, Channels, Clock,
1
Press ACTION
M A I N MENU
TV
VCR
LANGUAGE
CH
CLOCK
EX I T
to display MAIN MENU.
SELECT :
SET
: ACT I ON
2
Clock
Channels
Language
1) Press
select “CH.”
1) Press
to
select language
icon.
to
1) Press
to
select “CLOCK.”
M A I N MENU
M A I N MENU
M A I N MENU
TV
VCR
LANGUAGE
CH
CLOCK
EX I T
TV
VCR
LANGUAGE
CH
CLOCK
EX I T
SELECT :
SET
: ACT I ON
SELECT :
SET
: ACT I ON
2) Press ACTION.
SET UP CHANNEL
2) Press ACTION
repeatedly.
ANTENNA : CABLE
ANTENN
ABLE
AUTO SET
CHANNEL CAPT I ON
WEAK S I GNAL D I SPLAY : OFF
MENU PR I NC I PAL
HOLA
TV
VCR
IDIOMA
CANAL
REL OJ
SAL I R
SELECT :
SET
:
END
: ACT I ON
3) Press
to select
“ANTENNA,” then
press to set your
antenna system
(“TV” or “CABLE”).
ELEG I R :
F I JAR : ACT I ON
For Spanish
MENU
BONJOUR
T ELE
to select
4) Press
“AUTO SET,” then
press .
LANGUE
MAGNET .
CANAL HORLOGE SORT I E
SEL.
:
REGLER : ACT I ON
• After Channel Auto Set is
finished, Clock Auto Set
will be performed.
For French
M A I N MENU
VCR
LANGUAGE
CH
CLOCK
EX I T
SELECT :
SET
: ACT I ON
2) Press ACTION.
SET CLOCK
AUTO CLOCK SET
MANU
NUAL
AL
T I ME ZONE ADJUST : 0
SELECT :
SET
:
: ACT I ON
END
(“TIME ZONE ADJUST”
appears only when auto
clock is set.)
3) Press
to select
“MANUAL” or
“AUTO CLOCK
SET” and press .
• For Auto Clock Set,
select “AUTO CLOCK
SET,” then press CH .
SET CLOCK
2 / 7/2001 WED 12: 00
00PM
DST : ON
HELLO
TV
VCR
LANGUAGE
CH
CLOCK
EX I T
SELE CT HOUR
SE
SELECT :
SET
:
END
: ACT I ON
4) Press
and
to select
press
and set the month,
date, year, time,
and DST (Daylight
Saving Time).
5) Press ACTION
twice to start the
clock and exit this
mode.
SELECT :
SET
: ACT I ON
For English
3) Press
to
select “EXIT.”
Press ACTION to
exit.
12
TV
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
VV13F1 P12-21 Basic-TV.p65
12
01/09/19, 10:45
Time
Clock,
Time Zone Adjust
POWER
NUMBER Keys
ADD/DLT
Time Zone Adjust
(Only when Auto Clock is set.)
SELECT/SET
:CH UP
:CH DOWN
:VOL UP
:VOL DOWN
ACTION
M A I N MENU
TV
VCR
LANGUAGE
CH
CLOCK
EX I T
Basic Operation
1) Press
to
select “CLOCK.”
SELECT :
SET
: ACT I ON
2) Press ACTION.
SET CLOCK
ACTION key on
the unit
AUTO CLOCK SET
MANUAL
T I ME ZO
ZONE ADJUSTT : 0
SELECT :
SET
:
: ACT I ON
END
Using
STOP/EJECT REW/
3) Press
to
select TIME ZONE
ADJUST and
press or to
subtract or add
hour(s) as
necessary.
keys
VOL
VOL
CH
CH
ACTIO N
On Unit
You can operate the
menu screen using
unit buttons. To display
the menu, press STOP/
EJECT and REW
together with no tape
inserted. To exit the
menu, repeat above
with or without tape
inserted until normal
screen appears.
SET CLOCK
AUTO CLOCK SET
MANUAL
T I ME ZONE ADJUSTT : +1
+1
SELECT :
SET
:
END
: ACT I ON
4)Press ACTION
twice to exit.
On Remote
On Unit
: CH UP
: CH DOWN
: VOLUME UP
: VOLUME DOWN
Whenever the menu or
program screen is displayed,
CHANNEL UP/DOWN function
and VOLUME UP/
as
DOWN function as
only.
Add or Delete a Channel
To add channel:
To delete channel:
Select channel with
number keys and
press ADD/DLT.
Select channel with
or number keys
CH
and press ADD/DLT.
CHANNEL 08 ADDED
CHANNEL 08 DELE TED
13
VV13F1 P12-21 Basic-TV.p65
13
01/09/19, 10:45
TV Timer Features
ON-TIMER with Alarm
This unit can be set to automatically power on in one of 2
modes (TV, Playback).
You can also combine the On-Timer with a one minute alarm
that gradually increases in volume.
1
2
Press PROG to display SET PROGRAM
screen.
SET PROGRAM
T I MER PROGRAMMING
ON TIMER
SELECT :
SET
:
END
: PROG
3
Ready Check List
The clock is set to correct time.
<Model VV-2001 unit shown>
1) Press
to select
desired settings.
2) Press to set the
ON-TIMER TIME or
ON-TIMER mode.
ON T I MER
6:--AM
AM CH -ALARM : ON
SELE CT HOU
SE
OUR
SELECT :
SET
:
END
: PROG
• ON-TIMER mode
selection order
CH02
1)Press
to select
“ON TIMER.”
2)Press to display
ON TIMER screen.
CH03
• Make sure a tape is
inserted if Playback
mode is selected.
TIMER
CH125
POWER
VOL
CH
STOP/EJECT REW/
PLAY/REPEAT FF/
REC
TIMER
REC ON TIMER PROG TIMER
ACTION
CH01
VIDEO IN
AUDIO IN
PLAY
4
ON T I MER
6:00
00AM
AM CH08
ALARM : ON
ABC
SE
SELE CT ALARM
ALARM
CANCEL : ADD / DLT
SELECT :
SET
:
END
: PROG
CH
Press
to select
ALARM “ON” or
“OFF.”
ON TIMER
indicator
When “ON” is selected,
an alarm will gradually increase in volume for one
minute or until canceled by pressing any button
(including VOL + -).
To Make Corrections,
and
to move back and correct.
use
5
Press PROG to set ON TIMER.
• “ON TIMER SET” is displayed.
• ON TIMER Indicator lights on the unit.
Note
• If no button on the remote or unit
To Cancel ON-TIMER set,
Repeat steps 1 and 2. Then, press ADD/DLT to
clear the time in step 3. Now, press PROG to end.
“ON TIMER END” briefly appears on-screen.
18
(including a button used to turn off
the alarm) is pressed within 60
minutes after unit turns itself on,
it will turn itself back off.
Forassistance,pleasecall:1-800-211-PANA(7262)orsende-mailto:[email protected]
VV13F1 P12-21 Basic-TV.p65
18
01/09/19, 10:46
k List
Sleep Timer
rrect time.
This unit can be set for auto power off.
SLEEP
DISPLAY
ADD/DLT
SELECT/SET
:CH UP
:CH DOWN
:VOL UP
:VOL DOWN
Press SLEEP repeatedly
to set SLEEP TIMER.
SLEEP TIMER 30
• Pressing DISPLAY with
sleep timer set displays
remaining time.
SLEEP TIMER 60
Press SLEEP repeatedly
until “SLEEP TIMER 00”
appears to cancel.
SLEEP TIMER 90
SLEEP TIMER 00
Instant Alarm
SLEEP
1
2
1:00 (one minute)
2:00
3:00
Press TIMER on the unit to display the
instant alarm CANCEL/SET screen.
5 : 20PM
02 : 00
CANCEL : ADD / DLT
SET : CH
KEY ON UN I T
one-minute
increase
until 10:00
Press CH
on the
unit with CANCEL/SET
screen displayed to set
alarm. (Time changes in
the order shown left.)
Remaining Time
• Pressing TIMER repeatedly on the unit
will change display as follows.
9:00
10:00
15:00
20:00
25:00
five-minute
increase
until 30:00
30:00
40:00
50:00
ten-minute
increase
until 60:00
To cancel, press TIMER then press ADD/DLT on
the remote while CANCEL/SET screen is displayed.
To increase timer in progress, repeat step 2. Time
will be rounded up to next 1, 5, or 10 minute interval.
(See chart left.)
60:00 (Max)
<Example>
• If current time remaining is 12:15, countdown will
restart from 15:00.
• If current time remaining is 9:15, countdown will
restart from 10:00.
Note
• While timer function is in progress,
you can change channels on the unit
with CH
while “CANCEL/SET”
screen is not displayed.
3
Alarm will sound at 0: 00.
Press any button to stop
• The volume of the alarm gradually increases
for one minute and then continues to beep
until any button is pressed.
19
VV13F1 P12-21 Basic-TV.p65
19
01/09/19, 10:46
TV Operation
You can set a timer alarm up to 60 min. Useful when you are
cooking, etc.
Closed Caption System
Closed Caption is ...
This multi-use system not only allows the hearing impaired to enjoy selected programs,
but also makes useful information from TV stations available to everyone.
Closed Caption Mode Feature
1
2
Press ACTION
to display MAIN MENU.
M A I N MENU
TV
VCR
LANGUAGE
CH
CLOCK
EX I T
SELECT :
SET
: ACT I ON
3
SET UP TV
LOCK
CAPT I ON
N
I NPUT SELECT
V I DEO ADJUST
: TUNER
SELECT :
SET
:
END
: ACT I ON
4
: CAP C1
: CAP C1
SELECT :
SET
:
END
: ACT I ON
OFF
to
1)Press
select “CAPTION”.
2)Press to display
CAPTION screen.
Caption Mode: CAP C1 or C2
A narration of selected TV
programs is displayed.
Check TV program listings for
CC(Closed Caption)
broadcasts.
Caption Mode: TEXT C1 or
C2
The lower half of the screen
will be blocked out. When the
TV station broadcasts
information, such as program
listings, it will appear in this
space.
Caption Mode: OFF
Closed Caption / Text narration
will not be displayed.
CAPT I ON
CAPT I ON MODE
CC ON MUTE
to
1)Press
select “TV.”
2)Press ACTION to
display SET UP
TV screen.
Closed Caption Mode
Selections
CAP C1
TEXT C2
to
1)Press
select CAPTION
MODE.
2)Press
repeatedly to
select mode.
(See left.)
NOTE :
The closed caption or text
signal may be broadcast over
C1, C2, or both. Also, text
contents can vary so you may
wish to try different settings.
TEXT C1
CAP C2
5
Press ACTION three times to return
to the normal screen.
Recording and Playing Back a Closed Caption/Text Program
Record:
Record normally.
Closed Caption/ Text signal, if present, is recorded automatically.
Playback: Start playback. Do above steps to select desired caption mode.
20
Forassistance,pleasecall:1-800-211-PANA(7262)orsende-mailto:[email protected]
VV13F1 P12-21 Basic-TV.p65
20
01/09/19, 10:46
Caption On Mute Feature
Closed Caption narration, if available, is displayed
when MUTE button is pressed for silence.
1
2
MUTE
Press ACTION to display MAIN MENU.
M A I N MENU
TV
VCR
LANGUAGE
CH
CLOCK
EX I T
SELECT :
SET
: ACT I ON
3
SET UP TV
LOCK
CA
CAPT
PT I ON
N
I NPUT SELECT
V I DEO ADJUST
: TUNER
SELECT :
SET
:
: ACT I ON
END
ACTION
4
CAPT I ON
CA
CAPT
PT I ON MODE
MODE : OFF
OFF
CC ON MUTE
: CAP C1
SELECT :
SET
:
END
: ACT I ON
5
to
1)Press
select CAPTION
MODE.
2)Press
repeatedly to
select “OFF.”
1)Press
to select
CC ON MUTE.
2)Press repeatedly
to select desired
mode.
NO
CAP C1
CAP C2
6
7
to
1)Press
select “CAPTION”.
2)Press to display
CAPTION screen.
• Each press of will
change the display as
shown left.
• The caption may be
broadcast over CAP C1
or C2.
Press ACTION three times to return to
the normal screen.
Press MUTE to mute the sound and
display closed captioning.
• To cancel, press MUTE again.
21
VV13F1 P12-21 Basic-TV.p65
21
01/09/19, 10:46
TV Operation
SELECT/SET
:CH UP
:CH DOWN
:VOL UP
:VOL DOWN
to
1)Press
select “TV.”
2)Press ACTION to
display SET UP TV
screen.
Timer Recording
You can set up to 8 programs to be recorded while
you are away.
1
2
Press PROG to display SET PROGRAM
screen.
to select
1) Press
SET PROGRAM
Ready Check List
All connections are made.
Your unit is plugged in.
The clock is set to correct time.
The tape is long enough.
The record tab is in place.
TIMER
PROGRAMMING.
T I MER PR
PROGRAMMING
OGRAMMING
ON TIMER
2) Press to display
screen.
SELECT :
SET
:
END
: PROG
<Model VV-2001 unit shown>
• If a program is already in
, and
memory, press
to select an unused
program number.
3
START
STOP
CH
Press
to select
7 FR I --:-- --:-- -- and or to set the
TODAY
SLP
CATEGORY : N / A
------------------------ recording DATE.
DATE
SE
SELE CT START
START DAT
ATE
SELECT :
SET
:
: PROG / ACT I ON
END
Example
Today’s
Date
8
9
31
SELECT
7
• 1~31 = One time
• DAILY = MON~FRI
• WEEKLY SUN~SAT
= Same time once a week
/
WEEKLY
(SAT)
1
2
4
START
9 : 00 p
-- : --- : --- : --
STOP
12 : 00 a
-- : --- : --- : --
CH SPD
08 SP
-- --- --- --
CANCEL : ADD / DLT
SELECT 1 - 8 :
ENTER :
END
: PROG / ACT I ON
5
22
STOP/EJECT REW/
PLAY/REPEAT FF/
REC
TIMER
REC ON TIMER PROG TIMER
DAILY
WEEKLY
(SUN)
• start time, stop time
• Channel (or LINE for outside source)
• Category [N/A (not applicable), SPORTS, MOVIE,
COMEDY, MUSIC, DRAMA]
• Speed (SP, LP, SLP)
DT
day
----
CH
AUDIO IN
PROG TIMER indicator
Repeat step 3 to set:
P
1
2
3
4
VOL
ACTION
6
Selection Order
WEEKLY
(MON)
POWER
VIDEO IN
Press PROG (or
ACTION) to end the
program.
To Enter More Programs,
to select
press
and to set a blank
program number, and
then repeat step 3.
Press PROG twice (or ACTION)
to exit this mode.
• If you’re using a cable box, make sure that it is
tuned to the desired channel and the power is
left on for timer recording.
• PROG TIMER indicator lights on the unit.
Timer Recording Using
unit Buttons
You can set a Timer Recording
using ACTION key on the unit.
(See page 13.)
VOL
CH
STOP/EJECT REW/
ACTION
1 Press STOP/EJECT and REW
together without a tape inserted
to display MAIN MENU.
2 Press
+ - to select “VCR”
and STOP/EJECT and REW
together to display SET UP
VCR screen.
3 Press
to select “TIMER
PROGRAM” and + to display
the TIMER PROGRAM screen.
4 Repeat main steps 3 ~ 5.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
VV13F1 P22-31Timer-Advanced.p65
22
01/09/19, 10:49
Cancel a Timer Recording:
(Recording is in progress)
Hold down STOP for a few seconds
to cancel the Timer Recording.
• Any future daily or weekly recordings
will be performed as programmed.
Review, Replace or Clear Program
Contents : (Recording is not in progress)
1
2
Repeat steps 1 and 2 on page 22.
P
1
2
3
4
DT START STOP CH SPD
day 9 : 00
00p 12 : 00
00a 08 SP
8 10 : 00a 12 : 00p 125 SP
10 8 : 00p 9 : 00p 10 SP
SU 9 : 00p 10 : 00p L LP
Press
to select
the desired program.
CANCEL : ADD / DLT
SELECT 1 - 8 :
ENTER :
END
: PROG / ACT I ON
3
To Replace program...
START
STOP
CH
1) Press to display.
8 SAT
9:00
00PP 12
12:00
00A 08 2) Press
to select
SAT
ABC
TODAY
SP
CATEGORY : MOV I E
and press or
---------------------------------------------SE
to set new program
SELE CT START
START DAT
ATE
SELECT :
SET
:
contents.
END
: PROG / ACT I ON
3) Press PROG (or
ACTION).
DATE
ADD/DLT
SELECT/SET
:CH UP
:CH DOWN
:VOL UP
:VOL DOWN
To Clear program...
PROG
DT START STOP CH
-- -- : -- -- : -- -8 10 : 00p 12 : 00a 125
10 8 : 00p 9 : 00p 10
SU 9 : 00p 10 : 00p L
SPD
-SP
SP
LP
Press ADD/DLT.
Timer Operation
P
1
2
3
4
SELECT 1 - 8 :
ENTER :
END
: PROG / ACT I ON
STOP
4
Press PROG twice (or ACTION)
to exit this mode.
Notes
• 2 minutes before Timer recording is performed,
“PLEASE PREPARE FOR TIMER REC” appears and/
or the PROG TIMER Indicator flashes. Be sure a
cassette with record tab is loaded and the unit is in
Stop mode.
• If the start times of two programs overlap, the lower
numbered program will have priority.
• If the start time for a Timer Recording comes up during
a normal recording or One Touch Recording (page 14),
the Timer Recording will not be performed.
• If there is a power interruption of more than one minute,
the recording may not be performed or continued.
• If “INCOMPLETE” appears after all items have been
set, check all entries and make necessary corrections.
23
VV13F1 P22-31Timer-Advanced.p65
23
01/09/19, 10:49
Tape Operation (continued)
Zero Search
Repeat Play
To quickly return to a specific tape counter location.
Set to see a recording over and over.
1
2
1
2
Press DISPLAY during playback to
display the Counter.
0 : 00 : 00
BEG I N
3
4
5
Press COUNTER
RESET at the
desired position to
reset to “0:00:00.”
Continue playback, rewind, or
fast forward.
Press STOP.
Press CM/ZERO
in stop mode to
start ZERO
SEARCH.
•
BEG I N
M A I N MENU
TV
VCR
LANGUAGE
CH
CLOCK
EX I T
SELECT :
SET
: ACT I ON
END
1 : 23 : 45
Press ACTION to display
MAIN MENU.
END
: Present position mark
: Zero position mark
• Unit goes into FF or REW mode and stops at
the last point the Counter was set to 0:00:00.
Note
• If a blank portion exists on the tape, and
depending on the position of the mark, the
mark display may be out of position.
3
SET UP VCR
REPEAT PLAY
T I MER PROGRAMMING
T I ME STAMP
: OFF
FF
: ON
SELECT :
SET
:
: ACT I ON
END
4
1) Press
to select “VCR.”
2) Press
ACTION to
display SET
UP VCR
screen.
1) Press
to
select
“REPEAT
PLAY.”
2) Press to
set REPEAT
PLAY “ON” or
“OFF.”
Press ACTION twice
to end setup.
Notes
• Playback repeats when tape end is reached or
unrecorded portion over 30 seconds is detected.
• During playback, you may also press PLAY/
REPEAT repeatedly on the unit to select
REPEAT “ON” or “OFF.”
Commercial Skip
By pressing the CM/ZERO button in Playback mode
you can skip over 1 to 3 minutes of recorded tape in
just a few seconds.
1
26
Press CM/ZERO repeatedly to
select skip time in Play mode.
• No indication appears.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
VV13F1 P22-31Timer-Advanced.p65
26
01/09/19, 10:49
Special VCR Features
Weak Signal Display ON/OFF
When “ON” is selected, the picture is displayed even
when a broadcast signal is weak or non-existent.
DISPLAY
COUNTER
RESET
SELECT/SET
:CH UP
:CH DOWN
:VOL UP
:VOL DOWN
1
2
Press ACTION to display MAIN
MENU.
M A I N MENU
TV
VCR
LANGUAGE
CH
CLOCK
EX I T
SELECT :
SET
: ACT I ON
3
CM/ZERO
SET UP CHANNEL
ANTENNA : CABLE
AUTO SET
CHANNEL CAPT I ON
EAK SS IGNAL
WEAK
GNAL D ISPLAY
SPLAY :OFF
OFF
SELECT :
SET
:
: ACT I ON
END
ACTION
1)Press
to select “CH.”
2)Press ACTION
to display SET
UP CHANNEL
screen.
to
1)Press
select WEAK
SIGNAL
DISPLAY .
2)Press to set
“ON” or “OFF.”
Notes
• “ON” = Picture is displayed regardless of signal
condition, and may not always be clearly
visible.
“OFF” = Screen turns solid blue when signal is
absent or weak.
• If unit is connected to equipment which has blue
back feature, selecting “ON” will have no effect on
the other equipment.
4
Press ACTION twice
to return to the normal screen.
VCR Lock
All operations are prohibited except Timer recording
and tape eject. Useful for families with small children.
VCR LOCK ACT I VATED
POWER
VOL
CH
STOP/EJECT REW/
PLAY/REPEAT FF/
REC
TIMER
REC ON TIMER PROG TIMER
ACTION
VIDEO IN
VCR LOCK OFF
AUDIO IN
REC
In stop mode, hold
down REC on the unit
without a cassette
inserted for 7 seconds
to turn “ON.” Please
ignore NO CASSETTE
warning.
Repeat above with or
without cassette to
turn “OFF.”
• VCR Lock is canceled automatically
after about 24 hours if clock is set.
27
VV13F1 P22-31Timer-Advanced.p65
27
01/09/19, 10:49
Advanced Operation
<Model VV-2001 unit shown>
Special VCR Features (continued)
Channel Caption is ...
Station names, e.g. ABC, TNN, etc. are set so they
will appear when a channel is selected. Choose 24
preset names (Preset Caption), or make up to 10
names of your own (Manual Caption).
Preset Caption
1
2
VCR
TV
CH
LANGUAGE
CLOCK
EX I T
SELECT :
SET
: ACT I ON
3
Manual Caption
Press ACTION to display MAIN MENU.
M A I N MENU
SET UP CHANNEL
ANTENNA : CABLE
AUTO SET
CHANNE
NNEL CAP
CAPT I ON
WEAK S I GNAL D I SPLAY : OFF
SELECT :
SET
:
END
: ACT I ON
4
PRESET CA
PRESET
CAPT
PT I ON
MANUAL CAPT I ON
SELECT :
SET
:
END
: ACT I ON
5
-----
PBS
CNN
ESPN
HBO
1) Press
to
select CHANNEL
CAPTION.
2) Press to
display screen.
• To create your own
captions, go to
“Manual Caption”.
PRESET CAPT I ON
ABC
CBS
FOX
NBC
1)Press
to select “CH.”
2)Press ACTION
to display SET
UP CHANNEL
screen.
1) Press
to
select PRESET
CAPTION.
2) Press to
display screen.
CHANNEL CAPT I ON
-----
SELECT :
SET
:
: ACT I ON
END
PRESET CAPT I ON
62
TNT
4 2 CBC
UPN
-- CTV 2 1
52
WB
3 5 TSN
DSC
-- GLOB 1 2 3
CLEAR : ADD / DLT KEY
SELECT :
SET
:
END
: ACT I ON
1) Press
to
select a station.
2) Press to
move cursor to
the right.
to
3) Press
select channel
number.
4) Press to set
preset captions.
• Repeat step 5 until the
Caption List is complete.
To Make Corrections
Press
Press
6
28
Ready Check List
You need a list of stations and the
channel numbers you receive them on.
, then to select channel number.
to change, or ADD/DLT to delete.
Press ACTION four times to end setup.
1
2
Do “Preset Caption” steps 1~3
(see left).
1)Press
to select
MANUAL
CAPTION.
2)Press to
display
screen.
CHANNEL CAPT I ON
PRESET CAPT I ON
MANU
ANUAL CA
CAPT
PT I ON
SELECT :
SET
:
: ACT I ON
END
3
MANUAL CAPT I ON
CH NUMBER
CAPT I ON
----
O2
SELECT :
SET
:
: ACT I ON
END
1)Press
to select CH
NUMBER.
2)Press to
move cursor
to the right.
• Channels already set and channels deleted
from Channel Memory are not displayed.
• You can set a total of ten channel captions
with up to four characters each.
4
MANUAL CAPT I ON
CAPT I ON
CH NUMBER
A---
O2
CLEAR : ADD / DLT
SELECT :
SET
:
: ACT I ON
END
A
B
C
9
Press
to
select and
to enter your
caption.
• Characters
change in the
following order.
Z BLANK
2 1 0 /
&
!
• Press repeatedly to move the cursor
to “CH NUMBER.” Repeat steps 3 and
4 as desired.
To Make Corrections
Press
Press
5
, then to select channel number.
to change, or ADD/DLT to delete.
Press ACTION four times to end
setup.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
VV13F1 P22-31Timer-Advanced.p65
28
01/09/19, 10:49
Ready Check List
The clock is set to correct time.
The record tab is in place.
Time Stamp Feature
This unit writes program data (see example below) for
about the first 10 seconds of every recording. The
information is then displayed about 10 seconds after
playback begins.
ADD/DLT
SELECT/SET
:CH UP
:CH DOWN
:VOL UP
:VOL DOWN
1
2
Press ACTION to display MAIN MENU.
M A I N MENU
TV
VCR
LANGUAGE
CH
CLOCK
EX I T
SELECT :
SET
: ACT I ON
3
SET UP VCR
REPEAT PLAY
T I MER PROGRAMMING
T I ME STA
STAMP
ACTION
SELECT :
SET
:
END
: ACT I ON
: OFF
: ON
1)Press
to
select “VCR.”
2)Press ACTION
to display SET
UP VCR screen.
to
1)Press
select TIME
STAMP.
2)Press to set
“ON” or “OFF.”
• When “OFF” is selected, the program data
is written on the tape, but will not be displayed.
Press ACTION twice to return
to normal screen.
<Time Stamp Example >
Normal/ One
Touch Recording
Timer Recording
When Clock is not set...
SET UP CHANNEL
ANTENNA : CABLE
AUTO SET
CHANNEL CAPT I ON
WEAK S I GNAL D I SPLAY : OFF
EAK S GNAL
SPLAY OFF
SELECT :
SET
:
END
: ACT I ON
29
VV13F1 P22-31Timer-Advanced.p65
29
01/09/19, 10:49
Advanced Operation
4
V-Chip Control Feature
Process of V-Chip Control
Feature
Enter Code
Setup
Blocking
V-Chip Control Feature is...
This unit has a built-in V-Chip Control which allows
you to block unwanted TV usage based on US
MOVIES and US TV PROGRAMS Ratings.
Enter Secret Code
A 4-digit code must be entered to view a blocked program or
change rating settings.
1
2
Press ACTION to display MAIN MENU.
M A I N MENU
TV
VCR
LANGUAGE
CH
CLOCK
EX I T
SELECT :
SET
: ACT I ON
3
SET UP TV
LOCK
CAPT I ON
I NPUT SELECT
V I DEO ADJUST
: TUNER
SELECT :
SET
:
: ACT I ON
END
4
LOCK
ENTER 4-D I G I T CODE
---ENTER : 0 - 9
: ACT I ON
END
LOCK
CONF I RM 4-D I G I T CODE
****
****
RECOGN I ZED
CHANGE CODE : ADD / DLT
CONT I NUE :
: ACT I ON
END
30
ADD/DLT
SELECT/SET
:CH UP
:CH DOWN
:VOL UP
:VOL DOWN
1)Press
to select
LOCK.
2)Press to display
screen.
ACTION
1) Press number
keys to enter your
secret code.
2) Enter same code
again for confirmation.
• Step 2) not necessary
To Make Corrections
when changing rating
Press repeatedly to
or secret code.
move the cursor. Press • Take care that you are
number keys to make
not observed entering
the correction.
the secret code.
5
NUMBER Keys
1)Press
to
select “TV.”
2)Press ACTION to
display SET UP TV
screen.
Press to display US
Ratings menu
(see page 31).
Or
Press ACTION
three times to exit.
Changing your secret code
• You will need your current
code. Do steps 1 ~ 4. In step
5, press ADD/DLT to clear
current code. Repeat steps 4
and 5 to enter new code.
Notes
• DO NOT forget your secret code.
• Once ratings are set, restricted tapes
or programs cannot be accessed
unless the secret code is entered.
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
VV13F1 P22-31Timer-Advanced.p65
30
01/09/19, 10:49
V-Chip Control Feature (continued)
Process of V-Chip Control Feature
Enter Code
Setup
Blocking
US MOVIES RATINGS
Blocking Message
<When V-Chip Control is activated>
• If a program or
ABC
movie exceeds the
ratings you have
PROGRAM RAT I NG EXCEEDED
set, a message will
RAT I NG : PG-1 3
ACCESS CODE
---appear on a black
ENTER : 0-9
background and
sound is muted.
To View a Blocked Program / Movie
[Temporarily Deactivate V-Chip Control]
Enter your secret code (ACCESS CODE)
in the Blocking Message screen.
G
PG
PG-13
R
NC-17
X
GENERAL AUDIENCE:
All ages admitted.
PARENTAL GUIDANCE:
Some material may not be suitable for
children.
PARENTS CAUTIONED:
Some material may be inappropriate
for children under 13.
RESTRICTED:
Children under 17 must be
accompanied by a parent or adult.
OVER AGE 17 ONLY:
No one 17 and under admitted.
ADULTS ONLY:
• V-Chip Control is reactivated when power is
turned off or power failure occurs.
[Deactivate V-Chip Control]
Enter your secret code (steps 1-4 page
30). Then, set US MOVIES and/or US TV
PROGRAMS to “OFF” using
and
keys. (Ratings set on page 31 is retained
and will be in effect when V-Chip Control is
activated again.)
DISPLAY
SELECT/SET
:CH UP
:CH DOWN
:VOL UP
:VOL DOWN
US TV PROGRAMS RATINGS:Chart 1
TV-Y
FOR ALL CHILDREN:
Content specifically geared to young
viewers ages 2-6.
TV-Y7 FOR AGE 7 AND OLDER:
May contain mild physical or comedic
violence which may frighten children
under 7.
TV-G GENERAL AUDIENCE:
Contains little or no violence, strong
language, or sexual dialogue or
situations.
TV-PG PARENTAL GUIDANCE:
May contain infrequent coarse
language, limited violence, some
suggestive sexual dialogue and
situations.
TV-14 PARENTS CAUTIONED:
May contain sophisticated themes,
sexual situations, strong language, and
more intense violence.
TV-MA MATURE AUDIENCE:
May contain mature themes, profane
language, graphic violence, and sexual
situations.
ACTION
US TV PROGRAMS RATINGS: Chart 2
2
FV
V
S
L
D
32
Fantasy Violence
Violence
Sexual Situations
Adult Language
Sexually Suggestive Dialogue
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
VV13F1 P22-31Timer-Advanced.p65
32
01/09/19, 10:49
On-Screen Display (OSD)
VCR Status & Clock Display
Press DISPLAY
to display or remove the overlay.
Channel Caption
(See page 28.)
Function Status
Current Time
Rec Time
Remaining
(OTR mode only,
see page 14.)
REC
0 : 25
Counter
ABC
1 2 : 0 0PM
-0 : 1 2 : 3 4
SP
12 / 2 7 / 1 9 9 9 MON
ON
12 : 0 0PM - 1 : 0 0PM
CH 0 8 ABC MO
MOV I E
Blue Screen Display
Whenever a blank section of a tape comes
up in Play mode, or when the selected
channel has no broadcast signal with the
Weak Signal Display set to “OFF” (see
page 27), the screen will turn solid blue.
Channel & Function Display
When a function button is pressed (PLAY,
FF, etc.) or you change channels, the unit
mode or channel number will be displayed.
(Some station names may also appear if
Channel Caption is set. See page 28.)
08
Time Stamp Data
(See page 29.)
Tape Speed
Warning and Instruction Displays
ABC
These displays will alert you to a missed
operation or provide further instructions.
Caution
Page
NO CH FOUND PLEASE CHECK
ANTENNA CABLE CONNECTION
THEN PUSH CH UP KEY AGAIN
• If no active channels are found for CHANNEL
MEMORY...
8 - 11
PLEASE SET CLOCK BEFORE
PROGRAMMING
• If you attempt to set or review a Timer Recording,
or set the On-Timer and the Clock is not set...
8 - 13
CHECK CASSETTE RECORD TAB
• If you press REC, and a cassette is inserted with
no record tab...
4, 14
TO CANCEL TIMER REC HOLD DOWN
STOP KEY FOR APPROX 3 SEC
• If you press STOP during a Timer Recording...
23
NO CASSETTE
PLEASE INSERT A CASSETTE
• If you press PLAY, FF, REW, or REC without a
cassette inserted...
14
PLEASE PREPARE FOR TIMER REC
• If the unit is not in Stop mode or a cassette with
record tab is not inserted two minutes before a
Timer Recording is about to begin...
22, 23
VIDEO HEADS MAY NEED CLEANING
PLEASE INSERT HEAD CLEANING
CASSETTE OR REFER TO MANUAL
END: PLAY KEY
• If head cleaning becomes necessary while playing
back a tape...
VCR LOCK ACTIVATED
• If you press a function button other than STOP/EJECT
or POWER while the unit is in VCR Lock mode...
34
27
33
VV13F1 P32-40 For Your Information.p65
33
01/09/19, 10:52
For Your Information
OSD
Before Requesting Service
Check the following points once again if you are having trouble with your unit.
Power
Correction
No power…
• Completely insert Power Plug into an AC outlet.
• Set POWER button to ON.
Monitor
Correction
No picture or sound...
Poor picture with normal sound...
•
•
•
•
Poor sound with normal picture...
Poor TV reception...
No color or poor color...
Ghost (multiple) images...
TV programs cannot be watched...
Channel cannot be selected...
•
•
•
•
•
•
VCR
Correction
TV program cannot be
recorded...
•
•
•
•
Timer recording cannot be
performed…
•
•
No playback picture, or the playback •
picture is noisy or contains streaks... •
•
VCR cannot be controlled...
•
Make sure your antenna system (TV or CABLE), is correctly set. (P. 8-11)
Completely insert Power Plug into an AC outlet.
Set POWER button to ON.
Adjust BRIGHTNESS, SHARPNESS, and PICTURE controls in
the SET UP TV menu. (P. 17)
Adjust VOLUME control. (P. 16)
Adjust SHARPNESS and PICTURE controls in the SET UP TV menu. (P. 17)
Adjust TINT and COLOR controls in the SET UP TV menu. (P. 17)
Install a directional antenna.
Make sure the selected channel is in unit’s memory. (P. 12, 13)
Only the channel being recorded can be viewed on this unit.
Make sure your antenna system (TV or CABLE), is correctly set. (P. 8-11)
Make sure cassette record tab is intact. (P.4)
Check that clock is set to current time and date.
Make sure DSS/CABLE box (if used) is left on and tuned to
channel to be recorded.
Set recording Start/Stop times correctly. (P. 22-23)
Timer recording may not be performed or continued if a power
interruption of more than 1 minute occurs before or during a Timer
recording even after power is restored.
Adjust TRACKING control in either direction. (P. 34)
Try Head Cleaning. (P. 34)
Make sure VCR LOCK is set to off. (P. 27)
Make sure unit is not in a Timer Record operation.
Remote Control
Correction
Unit cannot be controlled...
• Aim remote at remote sensor on unit (P. 7) so that signal is
unobstructed.
• Inspect the remote batteries. (P. 4)
• Make sure VCR LOCK is set to off. (P. 27)
• Exposing unit remote sensor to direct fluorescent or outdoor light
may cause signal interference.
• Check remote batteries.
ACTION, PROG and FM/TV
buttons cannot be selected...
Correction
Video cassette cannot be inserted...
Video cassette cannot be removed...
Tape cannot be ejected or inserted...
Video cassette ejects when a
recording is started, or the power
is turned off for timer recording...
In Stop mode, the VCR motor
(CYLINDER) continues to rotate...
•
•
•
•
VCR cannot be controlled...
Insert the cassette window side up; record tab facing you.
Completely insert Power Plug into an AC outlet.
Try ejecting or inserting the tape again after turning POWER off, then back on.
Make sure cassette record tab is intact. (P. 4)
• To enable Quick Play mechanism, the VCR cylinder will rotate for
about 3 minutes. This reduces response time from Stop to Play
mode and from Play to Rewind Search mode.
• Make sure VCR LOCK is set to off. (P. 27)
If you cannot resolve the problem, please call the Customer Satisfaction Center for
product assistance at 1-800-211-PANA(7262)
To locate an authorized servicenter call toll free 1-800-211-PANA(7262)
or send e-mail to : [email protected]
35
VV13F1 P32-40 For Your Information.p65
35
01/09/19, 10:52
For Your Information
Miscellaneous
Service Center List
For Product Information, Operating Assistance, Literature Request, Dealer Locations,
and all Customer Service inquires please contact:
1-800-211-PANA(7262), Monday-Friday 9am-9pm Saturday-Sunday 9am-7pm, EST.
or send e-mail : [email protected]
Web Site: http://www.panasonic.com
You can purchase parts, accessories or locate your
nearest servicenter by visiting our Web Site.
Accessory Purchases:
1-800-332-5368 (Customer Orders Only)
Panasonic Services Company 20421 84th Avenue South, Kent, WA 98032
(6 am to 5 pm Monday - Friday; 6 am to 10:30 am Saturday; PST)
(Visa, Master Card, Discover Card, American Express, Check)
Factory Servicenter Locations
CALIFORNIA
GEORGIA
MINNESOTA
TEXAS
6550 Katella Avenue
Cypress, CA 90630
800 Dubuque Avenue
S. San Francisco,
CA 94080
3878 Ruffin Road
Suite A
San Diego, CA 92123
8655 Roswell Road
Suite 100
Atlanta, GA 30350
7850-12th Avenue South
Airport Business Center
Bloomington, MN 55425
13615 Welch Road
Suite 101
Farmers Branch,
TX 75244
OHIO
ILLINOIS
1709 North Randall Road
Elgin, IL 60123
WASHINGTON
20425-84th Avenue
South
Kent, WA 98032
PENNSYLVANIA
FLORIDA
3700 North 29th Avenue
Suite 102
Hollywood, FL 33020
2236 Waycross Road
Civic Center Plaza
Forest Park, OH 45240
MASSACHUSETTS
60 Glacier Drive,
Suite G
Westwood, MA 02090
2221 Cabot Blvd. West
Suite B
Langhorne, PA 19047
HAWAII
99-859 Iwaiwa Street
Aiea, Hawaii 96701
Phone (808) 488-1996
Fax (808) 486-4369
Service in Puerto Rico
Matsushita Electric of Puerto Rico, Inc. Panasonic Sales Company/ Factory Servicenter:
Ave. 65 de Infanteria. Km. 9.5 San Gabriel Industrial Park Carolina, Puerto Rico 00985
Phone (787) 750-4300 Fax (787) 768-2910
As of June 2001
36
For assistance, please call : 1-800-211-PANA(7262) or send e-mail to : [email protected]
VV13F1 P32-40 For Your Information.p65
36
01/09/19, 10:52
Limited Warranty
Panasonic Consumer Electronics Company,
Division of Matsushita Electric Corporation
of America, One Panasonic Way
Secaucus, New Jersey 07094
Panasonic Sales Company,
Division of Matsushita Electric of Puerto Rico, Inc.
AVE. 65 de Infantería, Km. 9.5 San Gabriel
Industrial Park Carolina, Puerto Rico 00985
PANASONIC/QUASAR Video Products
Limited Warranty
Panasonic Consumer Electronics Company or Panasonic Sales Company (collectively referred to as “the
Warrantor”) will repair or replace this product with new or refurbished parts or equivalent product, free of charge, in
the USA or Puerto Rico, in the event of a defect in materials or workmanship as follows (all time periods commence
from the date of the original purchase):
PARTS
ONE (1) YEAR, EXCEPT
CCD IMAGE SENSOR
CCD IMAGE SENSOR
- SIX (6) MONTHS
LABOR
NINETY (90) DAYS
SERVICE
Carry-In or Mail-In
CONTACT NUMBER
1-800-211-PANA(7262)
DVD/VCR DECK ONE (1) YEAR
ONE (1) YEAR, EXCEPT
DIGITAL STILL
CCD IMAGE SENSOR
CAMERA
CCD IMAGE SENSOR
- SIX (6) MONTHS
ONE (1) YEAR
A/V MIXER
NINETY (90) DAYS
NINETY (90) DAYS
Carry-In or Mail-In
1-800-211-PANA(7262)
PRODUCT
CAMCORDER
Carry-In or Mail-In
1-800-272-7033
NINETY (90) DAYS
NINETY (90) DAYS
TV/VCR,
TV/DVD/VCR
COMBINATION
ONE (1) YEAR,
EXCEPT CRT
CRT - TWO (2) YEARS
NINETY (90) DAYS
NINETY (90) DAYS
CRT - NINETY (90) DAYS
TV/HDR
COMBINATION
ONE (1) YEAR,
EXCEPT CRT
CRT - TWO (2) YEARS
NINETY (90) DAYS
CRT - NINETY (90) DAYS
Carry-In or Mail-In
1-800-211-PANA(7262)
Carry-In: 21” CRT and 1-800-211-PANA(7262)
Smaller
In-Home or Carry-In:
22” CRT and Larger
In-Home or Carry-In 1-888-843-9788
37
VV13F1 P32-40 For Your Information.p65
37
01/09/19, 10:52
For Your Information
Batteries (if included) - New rechargeable batteries in exchange for defective rechargeable batteries for ten (10)
days. Non-rechargeable batteries are not warranted.
Tape (if included) - New video cassette tape in exchange for a defective video cassette tape for five (5) days.
Memory cards (if included) - Exchange defective item for new one for ninety (90) days.
In-home, carry-in or mail-in service, as applicable, in the USA can be obtained during the warranty period by
contacting a Panasonic Services Company (PASC) Factory Servicenter listed in the Servicenter Directory.
Or call toll free contact number listed above, to locate an authorized PASC Servicenter. Carry-in or mail-in service
in Puerto Rico can be obtained during the warranty period by calling the Panasonic Sales Company telephone
number listed in the Servicenter Directory.
This warranty is extended only to the original purchaser. A purchase receipt or other proof of the date of the original
purchase is requires before warranty service is rendered.
This warranty only covers failures due to defects in materials and workmanship, which occur during normal use and
does not cover normal maintenance, including, but not limited to, video and audio head cleaning. The warranty
does not cover damage which occurs in shipment, or failures which are caused by products not supplied by the
warrantor, or failures which result from accident, misuse, abuse, neglect, mishandling, misapplication, alteration,
modification, faulty installation, set-up adjustments, improper antenna, inadequate signal pickup, maladjustment of
consumer controls, improper operation, power line surge, improper voltage supply, lightning damage, commercial
use such as hotel, office, restaurant, or other business or rental use of the product, or service by anyone other than
a PASC Factory Servicenter or a PASC authorized Servicenter, or damage that is attributable to acts of God.
LIMITS AND EXCLUSIONS
There are no express warranties except as listed above.
THE WARRANTOR SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING,
WITHOUT LIMITATION, DAMAGE TO RECORDING MEDIA) RESULTING FROM THE USE OF THIS PRODUCTS,
OR ARISING OUT OF ANY BREACH OF THE WARRANTY. ALL EXPRESS AND IMPLIED WARRANTIES,
INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, ARE
LIMITED TO THE APPLICABLE WARRANTY PERIOD SET FORTH ABOVE. Some states do not allow the
exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so
the above exclusions or limitations may not apply to you. This warranty gives you specific legal rights and you may
also have other rights, which vary, from state to state. If a problem with this product develops during or after the
warranty period, you may contact your dealer or Servicenter. If the problem is not handled to your satisfaction, then
write to the Consumer Affairs Department at the Panasonic Consumer Electronics Company address above.
SERVICE CALLS WHICH DO NOT INVOLVE DEFECTIVE MATERIALS OR WORKMANSHIP AS DETERMINED
BY THE WARRANTOR, IN ITS SOLE DISCRETION, ARE NOT COVERED. COSTS OF SUCH SERVICE CALLS
ARE THE RESPONSIBILITY OF THE PURCHASER.
warvid 02/ 12/ 2001
INDEX
A
B
C
D
E
F
H
I
L
N
O
Accessories .................................................. 4
Audio Mute ................................................. 16
Auto Operation Functions ........................... 25
Batteries ....................................................... 4
Before Requesting Service ......................... 35
Before Using ................................................. 4
Blocking Message ...................................... 32
Blue Screen Display ................................... 33
Caption On Mute ........................................ 20
Channel ........................................... 8 -13, 33
Channel Caption ......................................... 28
Clock .......................................................... 12
Closed Caption ........................................... 20
Commercial Skip ........................................ 26
Connections ......................................... 8 - 11
Connections, DSS / Cable Box ............ 10 -11
Connections, Outdoor Antenna ............... 8 - 9
Copy Your Tapes (Dubbing) ....................... 15
DST (Daylight Saving Time) ....................... 34
Eject tape ................................................... 14
Fast Forward .............................................. 14
Forward Search .......................................... 14
Frame by Frame Advance .......................... 14
Front Panel Indicators .................................. 7
Function Display ......................................... 33
Head Cleaning ............................................ 34
Important Safeguards and Precautions ........ 2
Index Search .............................................. 24
Initial Setup for ANT. / Cable Connection ..... 8
Initial Setup for DSS / Cable box Connection .. 10
Input Mode ................................................. 15
INSTANT ALARM ....................................... 19
Language .............................................. 8 - 13
Limited Warranty ........................................ 37
Location of Controls ............................... 6 - 7
NIGHT Mode .............................................. 16
100 Key ...................................................... 16
One Touch Recording ................................ 14
ON-TIMER with Alarm ................................ 18
P
Q
R
S
T
U
V
W
Z
Phones .................................................. 16
Playback ................................................ 14
Picture Adjustment ................................ 17
Program End Search ............................. 24
Quality Picture ....................................... 34
Rapid Tune ............................................ 16
Rec(ord) ................................................ 14
Record/Playback Speed Settings .......... 34
Remote Control Buttons .......................... 6
Repeat Play ........................................... 26
Reset Language, Channels, Clock ........ 12
Reset unit ................................................ 9
Reverse Search ..................................... 14
Rewind .................................................. 14
Secret Code .......................................... 30
Service Center List ................................ 36
SELF-DEMO Mode .................................. 4
Sleep Timer ........................................... 19
Slow Motion ............................................. 4
Spanish Quick Use Guide ..................... 38
Special VCR Features ........................... 27
Specifications ........................................ 34
Still Picture ............................................ 14
STOP .................................................... 14
Tape Erasure Prevention ......................... 4
Tape Position Display ............................ 25
Time Stamp ........................................... 29
Time Zone Adjust .................................. 13
Timer Program Review, Replace, Clear 23
Timer Recording .................................... 22
Timer Recording Cancellation ............... 23
TV Operation ......................................... 16
TV Timer Features ................................ 18
Unit, Front/Rear view ............................... 7
US MOVIES/TV PROGRAMS Ratings .. 31
VCR Lock .............................................. 27
VCR Status & Clock Display ................. 33
V-Chip Control Feature .......................... 30
Warning and Instruction Displays .......... 33
Weak Signal Display ON/OFF ............... 27
Zero Search ........................................... 26
Panasonic Consumer Electronics Company,
Division of Matsushita Electric Corporation of America
One Panasonic Way Secaucus,
New Jersey 07094
Panasonic Sales Company (“PSC”),
Division of Matsushita Electric of Puerto Rico, Inc.
Ave. 65 de Infanteria. Km. 9.5
San Gabriel Industrial Park, Carolina, Puerto Rico 00985
VV13F1 P32-40 For Your Information.p65
40
Q
Printed in U.S.A
LSQT0502A
M0801-0
01/09/19, 10:53
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement