Victron MultiPlus inverter chargers

Victron MultiPlus inverter chargers
MultiPlus inverter / charger
800VA - .5kVA
Lithium Ion battery compatible
www.victronenergy.com
Two AC Outputs
The main output has no-break functionality. The MultiPlus takes over the supply to the connected loads in the
event of a grid failure or when shore/generator power is disconnected. This happens so fast (less than
20 milliseconds) that computers and other electronic equipment will continue to operate without disruption.
The second output is live only when AC is available on one of the inputs of the MultiPlus. Loads that should not
discharge the battery, like a water heater for example can be connected to this output (second output available
on models rated at 3kVA and more).
Virtually unlimited power thanks to parallel operation
Up to 6 Multis can operate in parallel to achieve higher power output. Six 24/5000/120 units, for example, will
provide 25 kW / 30 kVA output power with 720 Amps charging capacity.
Three phase capability
In addition to parallel connection, three units of the same model can be configured for three-phase output. But
that’s not all: up to 6 sets of three units can be parallel connected for a huge 75 kW / 90 kVA inverter and more
than 2000 Amps charging capacity.
MultiPlus
24/3000/70
PowerControl - Dealing with limited generator, shore side or grid power
The MultiPlus is a very powerful battery charger. It will therefore draw a lot of current from the generator or
shore side supply (nearly 10A per 5kVA Multi at 230VAC). With the Multi Control Panel a maximum generator or
shore current can be set. The MultiPlus will then take account of other AC loads and use whatever is extra for
charging, thus preventing the generator or shore supply from being overloaded.
PowerAssist - Boosting the capacity of shore or generator power
This feature takes the principle of PowerControl to a further dimension. It allows the MultiPlus to supplement
the capacity of the alternative source. Where peak power is so often required only for a limited period, the
MultiPlus will make sure that insufficient shore or generator power is immediately compensated for by power
from the battery. When the load reduces, the spare power is used to recharge the battery.
Solar energy: AC power available even during a grid failure
The Quattro can be used in off grid as well as grid connected PV and other alternative energy systems.
Loss of mains detection software is available.
System configuring
In case of a stand-alone application, if settings have to be changed, this can be done in a matter of
minutes with a DIP switch setting procedure.
Parallel and three phase applications can be configured with VE.Bus Quick Configure and VE.Bus System
Configurator software.
Off grid, grid interactive and self-consumption applications, involving grid-tie inverters and/or MPPT
solar chargers can be configured with Assistants (dedicated software for specific applications).
MultiPlus Compact
12/2000/80
On-site Monitoring and control
Several options are available: Battery Monitor, Multi Control Panel, Ve.Net Blue Power panel, Color Control
panel, smartphone or tablet (Bluetooth Smart), laptop or computer (USB or RS232).
Remote Monitoring and control
Victron Ethernet Remote, Victron Global Remote and the Color Control Panel.
Data can be stored and displayed on our VRM (Victron Remote Management) website, free of charge.
Remote configuring
When connected to the Ethernet, systems with a Color Control panel can be accessed and settings can be
changed.
Color Control panel, showing a
PV application
MultiPlus
12 Volt
24 Volt
48 Volt
PowerControl
PowerAssist
Transfer switch (A)
Input voltage range (V DC)
Output
Cont. output power at 25 °C (VA) (3)
Cont. output power at 25 °C (W)
Cont. output power at 40 °C (W)
Peak power (W)
Maximum efficiency (%)
Zero-load power (W)
Zero load power in AES mode (W)
Zero load power in Search mode (W)
AC Input
Charge voltage 'absorption' (V DC)
Charge voltage 'float' (V DC)
Storage mode (V DC)
Charge current house battery (A) (4)
Charge current starter battery (A)
Battery temperature sensor
Auxiliary output (5)
Programmable relay (6)
Protection (2)
VE.Bus communication port
General purpose com. port
Remote on-off
Common Characteristics
Common Characteristics
Battery-connection
230 V AC-connection
Weight (kg)
Dimensions (hxwxd in mm)
Safety
Emission, Immunity
Automotive Directive
Anti-islanding
1) Can be adjusted to 60 HZ; 120 V 60 Hz on request
2) Protection key:
a) output short circuit
b) overload
c) battery voltage too high
d) battery voltage too low
e) temperature too high
f) 230 VAC on inverter output
g) input voltage ripple too high
C 12/800/35
C 24/ 800/16
C 12/1200/50
C 24/1200/25
C 12/1600/70
C 24/1600/40
C 12/2000/80
C 24/2000/50
Yes
Yes
16
Yes
Yes
16
Yes
Yes
16
Yes
Yes
30
800
700
650
1600
92 / 94
8 / 10
5/8
2/3
35 / 16
n. a.
n. a.
10
12/3000/120
24/3000/70
48/3000/35
Yes
Yes
16 or 50
24/5000/120
48/5000/70
Yes
Yes
100
INVERTER
9,5 – 17 V
19 – 33 V
38 – 66 V
Output voltage: 230 VAC ± 2%
Frequency: 50 Hz ± 0,1% (1)
1200
1600
2000
3000
5000
1000
1300
1600
2500
4500
900
1200
1450
2200
4000
2400
3000
4000
6000
10.000
93 / 94
93 / 94
93 / 94
93 / 94 / 95
94 / 95
8 / 10
8 / 10
9 / 11
15 / 15 / 16
25 / 25
5/8
5/8
7/9
10 / 10 / 12
20 / 20
2/3
2/3
3/4
4/5/5
5/6
CHARGER
Input voltage range: 187-265 VAC
Input frequency: 45 – 65 Hz
Power factor: 1
14,4 / 28,8 / 57,6
13,8 / 27,6 / 55,2
13,2 / 26,4 / 52,8
50 / 25
70 / 40
80 / 50
120 / 70 / 35
120 / 70
4 (12V and 24V models only)
yes
GENERAL
n. a.
n. a.
n. a.
Yes (16A)
Yes (25A)
Yes
a-g
For parallel and three phase operation, remote monitoring and system integration
n. a.
n. a.
n. a.
Yes
Yes
Yes
Operating temp. range: -40 to +50°C (fan assisted cooling) Humidity (non condensing): max 95%
ENCLOSURE
Material & Colour: aluminium (blue RAL 5012)
Protection category: IP 21
battery cables of 1.5 meter
M8 bolts
Four M8 bolts (2 plus and 2 minus connections)
G-ST18i connector
Spring-clamp
Screw terminals 13 mm2 (6 AWG)
10
10
12
18
30
375x214x110
520x255x125
362x258x218
444x328x240
STANDARDS
EN-IEC 60335-1, EN-IEC 60335-2-29, IEC 62109-1
EN55014-1, EN 55014-2, EN 61000-3-3, EN 61000-6-3, EN 61000-6-2, EN 61000-6-1
2004/104/EC
See our website
3) Nonlinear load, crest factor 3:1
4) At 25 ˚C ambient
5) Switches off when no external AC source available
6) Programmable relay that can a.o. be set for general alarm,
DC undervoltage or genset start/stop function
AC rating: 230V/4A
DC rating: 4A up to 35VDC, 1A up to 60VDC
Digital Multi Control Panel
Computer controlled operation and monitoring
BMV Battery Monitor
A convenient and low cost solution for
remote monitoring, with a rotary knob to
set Power Control and Power Assist levels.
Several interfaces are available:
- MK2.2 VE.Bus to RS232 converter
Connects to the RS232 port of a computer (see ‘A guide to VEConfigure’)
- MK2-USB VE.Bus to USB converter
Connects to a USB port (see ‘A guide to VEConfigure’)
- VE.Net to VE.Bus converter
Interface to VE.Net (see VE.Net documentation)
- VE.Bus to NMEA 2000 converter
- Victron Global Remote
The Global Remote is a modem which sends alarms, warnings and system status
reports to cellular phones via text messages (SMS). It can also log data from Victron
Battery Monitors, Multis, Quattro’s and Inverters to a website through a GPRS
connection. Access to this website is free of charge.
- Victron Ethernet Remote
To connect to the Ethernet.
- Color Control panel (see picture on page 1)
Behind the color LCD a Linux microcomputer runs open source software. The Color
Control (CCGX) provides intuitive control and monitoring for all products connected to
it. The list of Victron products that can be connected is endless: Inverters, Multis,
Quattros, all our latest MPPT solar chargers, BMV-700, BMV-600, Lynx Ion + Shunt and
more. The information can also be forwarded to our free remote monitoring
website: the VRM Online Portal.
The BMV Battery Monitor features an
advanced microprocessor control
system combined with high
resolution measuring systems for
battery voltage and charge/discharge
current. Besides this, the software
includes complex calculation
algorithms, like Peukert’s formula, to
exactly determine the state of charge
of the battery. The BMV selectively
displays battery voltage, current,
consumed Ah or time to go. The
monitor also stores a host of data
regarding performance and use of the
battery.
Several models available (see battery
monitor documentation).
Blue Power Panel
Connects to a Multi or Quattro and all
VE.Net devices, in particular the VE.Net
Battery Controller.
Graphic display of currents and voltages.
Victron Energy B.V. | De Paal 35 | 1351 JG Almere | The Netherlands
General phone: +31 (0)36 535 97 00 | Fax: +31 (0)36 535 97 40
E-mail: [email protected] | www.victronenergy.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement