PowerLite® S7/79/W7
Quick Setup
Before using the projector, make sure you read the safety instructions in the
User’s Guide on your projector CD.
Video Player
3
Troubleshooting
Turn the focus ring to sharpen the image.
Connect up to 3 video devices and use the remote control to switch between
them.
Audio in cable Audio out cable
(optional)
(optional)
If you see a blank screen...
S-Video
RCA video cable Component video
cable
to VGA cable
(composite video)
(optional)
(optional)
(optional)
4
Connect the projector
If you see a blank screen or the No signal message after turning on your
computer, check the following:
PowerLite 79/W7: to reduce or enlarge the image, turn the zoom ring.
Choose from the following connections:
Computer Monitor Port
PowerLite S7: to reduce or enlarge the image, press the Tele (reduce)
or Wide (enlarge) button on the projector. You can also use the Zoom
option in the projector’s Settings menu. See the User’s Guide on your
projector CD.
Connect a computer using the VGA cable that came with the projector.
•
Make sure the power light on the projector is green and not flashing,
and the A/V Mute slide is open.
•
Press the Source Search button on the projector or the remote control
to select the computer as the image source.
•If you’re using a Windows notebook, press the function key on your
keyboard that lets you display on an external monitor. It may be labelled
CRT/LCD or have an icon such as
. You may have to hold down the
Fn key while pressing it.
Where to get help
Manual
Connect one end to the projector’s Computer (Component Video) port,
and the other end to your computer’s
monitor port. If you are using a
notebook, switch it to external display. You can also connect an audio cable.
Turn on your equipment
5
If your image looks like
or
, you’ve placed the projector off to
one side of the screen at an angle. Place it directly in front of the center
of the screen, facing the screen squarely.
1
2
6
If your image looks like
projector to correct it.
Turn on your computer or video source.
Plug in the projector.
Computer USB Port (Windows® only)
or
, press the
or
buttons on the
Using the remote control
Connect a computer using a USB cable (not included).
Connect the square end of the USB cable to the projector’s
Type B
(square) USB port. Connect the flat end of the cable to any USB port on your
computer. You can also connect an audio cable.
Make sure the batteries are installed as shown (two included AA batteries).
3
For more information about using the projector, install the User’s Guide from
your projector CD.
Telephone Support Services
To use the Epson PrivateLine® Support service, call (800) 637-7661 and enter
the PIN on the Epson PrivateLine Support card included with your projector.
This service is available 6 AM to 6 PM, Pacific Time, Monday through Friday,
for the duration of your warranty period. You may also speak with a projector
support specialist by dialing one of these numbers:
U.S.:
(562) 276-4394, 6 AM to 6 PM, Pacific Time,
Monday through Friday
Canada: (905) 709-3839, 6 AM to 6 PM, Pacific Time,
Monday through Friday
Open the A/V Mute slide all the way.
Days and hours of support are subject to change without notice. Toll or long
distance charges may apply.
Internet Support
4
Press the
power button on the projector or remote control.
Power light
Follow the on-screen instructions to install the Epson USB Display software
(only on first connection). Then press the USB button on the remote control.
Connect a monitor to the Monitor Out port.
Choose which
source to display
Registration
Register today to get product updates, special promotions, and customer-only
offers. You can use the CD included with your projector, or register online at
www.epson.com/webreg. Power button
Turn off projector
display and sound
NOTE: If the software does not install automatically, open My Computer or
Computer, double-click EPSON_PJ_UD, then double-click EMP_UDSE.EXE.
External Monitor
Turn projector
on and off
Visit Epson’s support website at epson.com/support and select your
product for solutions to common problems. You can download utilities and
documentation, get FAQs and troubleshooting advice, or e-mail Epson with
your questions.
Get solutions to
common problems
The
power light flashes green, then stays on.
NOTE: To shut down the projector, press the
power button twice, then
unplug it. You don’t have to wait for the projector to cool down.
Change
presentation
slides (USB
connection only)
Access projector
menus
Control projector volume
Navigate projector menus
Adjust the image
1
If you don’t see an image, press the Source Search button on the
projector or remote control to select the image source.
NOTE: If you still see a blank screen or have other display problems, see
the troubleshooting tips on the right.
2
To raise the image, press the foot release button and lift the front of the
projector. Release the button to lock the foot in position.
NOTE: To use an external monitor, your computer must be connected to the
Computer (Component Video) port, not the USB port.
You can use the remote control to operate the projector. With the USB cable,
you can use the remote as a wireless mouse. For more information on using the
remote control, see your User’s Guide.
Epson is a registered trademark and Epson Exceed Your Vision is a registered logomark of Seiko Epson
Corporation. PowerLite and PrivateLine are registered trademarks of Epson America, Inc.
*411760900*
*411760900*
General Notice: Other product names used herein are for identification purposes only and may be trademarks of
their respective owners. Epson disclaims any and all rights in those marks.
This information is subject to change without notice.
© 2009 Epson America, Inc. 7/09
Printed in XXXXXX
CPD-27602
PowerLite® S7/79/W7
Quick Setup
Before using the projector, make sure you read the safety instructions in the
User’s Guide on your projector CD.
Video Player
3
Troubleshooting
Turn the focus ring to sharpen the image.
Connect up to 3 video devices and use the remote control to switch between
them.
Audio in cable Audio out cable
(optional)
(optional)
If you see a blank screen...
S-Video
RCA video cable Component video
cable
to VGA cable
(composite video)
(optional)
(optional)
(optional)
4
Connect the projector
If you see a blank screen or the No signal message after turning on your
computer, check the following:
PowerLite 79/W7: to reduce or enlarge the image, turn the zoom ring.
Choose from the following connections:
Computer Monitor Port
PowerLite S7: to reduce or enlarge the image, press the Tele (reduce)
or Wide (enlarge) button on the projector. You can also use the Zoom
option in the projector’s Settings menu. See the User’s Guide on your
projector CD.
Connect a computer using the VGA cable that came with the projector.
•
Make sure the power light on the projector is green and not flashing,
and the A/V Mute slide is open.
•
Press the Source Search button on the projector or the remote control
to select the computer as the image source.
•If you’re using a Windows notebook, press the function key on your
keyboard that lets you display on an external monitor. It may be labelled
CRT/LCD or have an icon such as
. You may have to hold down the
Fn key while pressing it.
Where to get help
Manual
Connect one end to the projector’s Computer (Component Video) port,
and the other end to your computer’s
monitor port. If you are using a
notebook, switch it to external display. You can also connect an audio cable.
Turn on your equipment
5
If your image looks like
or
, you’ve placed the projector off to
one side of the screen at an angle. Place it directly in front of the center
of the screen, facing the screen squarely.
1
2
6
If your image looks like
projector to correct it.
Turn on your computer or video source.
Plug in the projector.
Computer USB Port (Windows® only)
or
, press the
or
buttons on the
Using the remote control
Connect a computer using a USB cable (not included).
Connect the square end of the USB cable to the projector’s
Type B
(square) USB port. Connect the flat end of the cable to any USB port on your
computer. You can also connect an audio cable.
Make sure the batteries are installed as shown (two included AA batteries).
3
For more information about using the projector, install the User’s Guide from
your projector CD.
Telephone Support Services
To use the Epson PrivateLine® Support service, call (800) 637-7661 and enter
the PIN on the Epson PrivateLine Support card included with your projector.
This service is available 6 AM to 6 PM, Pacific Time, Monday through Friday,
for the duration of your warranty period. You may also speak with a projector
support specialist by dialing one of these numbers:
U.S.:
(562) 276-4394, 6 AM to 6 PM, Pacific Time,
Monday through Friday
Canada: (905) 709-3839, 6 AM to 6 PM, Pacific Time,
Monday through Friday
Open the A/V Mute slide all the way.
Days and hours of support are subject to change without notice. Toll or long
distance charges may apply.
Internet Support
4
Press the
power button on the projector or remote control.
Power light
Follow the on-screen instructions to install the Epson USB Display software
(only on first connection). Then press the USB button on the remote control.
Connect a monitor to the Monitor Out port.
Choose which
source to display
Registration
Register today to get product updates, special promotions, and customer-only
offers. You can use the CD included with your projector, or register online at
www.epson.com/webreg. Power button
Turn off projector
display and sound
NOTE: If the software does not install automatically, open My Computer or
Computer, double-click EPSON_PJ_UD, then double-click EMP_UDSE.EXE.
External Monitor
Turn projector
on and off
Visit Epson’s support website at epson.com/support and select your
product for solutions to common problems. You can download utilities and
documentation, get FAQs and troubleshooting advice, or e-mail Epson with
your questions.
Get solutions to
common problems
The
power light flashes green, then stays on.
NOTE: To shut down the projector, press the
power button twice, then
unplug it. You don’t have to wait for the projector to cool down.
Change
presentation
slides (USB
connection only)
Access projector
menus
Control projector volume
Navigate projector menus
Adjust the image
1
If you don’t see an image, press the Source Search button on the
projector or remote control to select the image source.
NOTE: If you still see a blank screen or have other display problems, see
the troubleshooting tips on the right.
2
To raise the image, press the foot release button and lift the front of the
projector. Release the button to lock the foot in position.
NOTE: To use an external monitor, your computer must be connected to the
Computer (Component Video) port, not the USB port.
You can use the remote control to operate the projector. With the USB cable,
you can use the remote as a wireless mouse. For more information on using the
remote control, see your User’s Guide.
Epson is a registered trademark and Epson Exceed Your Vision is a registered logomark of Seiko Epson
Corporation. PowerLite and PrivateLine are registered trademarks of Epson America, Inc.
*411760900*
*411760900*
General Notice: Other product names used herein are for identification purposes only and may be trademarks of
their respective owners. Epson disclaims any and all rights in those marks.
This information is subject to change without notice.
© 2009 Epson America, Inc. 7/09
Printed in XXXXXX
CPD-27602
Download PDF

advertising