MICRORISC GW-USB-13 IQRF USB Gateway User's Guide

Below you will find brief information for IQRF USB Gateway GW-USB-13. This gateway provides a connection between a USB port and an IQRF network. It features an OLED display for visualizing and setting up parameters in a given application. You can use it to control home automation systems, portable controllers, and pagers. It also serves as a diagnostic tool and a portable service tool for IQRF network management.

PDF Download

Document

GW-USB-13
IQRF USB Gateway with OLED
User's Guide
&copy; 2010 MICRORISC s.r.o.
www.iqrf.org
MNGWUSB13_100726
Page 1
GW-USB-13
Description
GW-USB-13 is an IQRF gateway with USB connectivity and
OLED display.
It is a part of the IQRF platform intended as an interface
between USB and an IQRF network or a portable interface
between a human and an IQRF network.
It allows to visualise and setup parameters in given
application. GW-USB-13 is a generic equipment, i.e. the
hardware is fixed and the user can realize specific
functionality by software only.
Applications should be developed using the DS-PAGER
development set.
Applications
Key features
• Home automation
• OLED display 1“, 96 x 64 pixels, white
• Portable controllers and pagers
• 8b microcontroller
• Diagnostic tool
• USB v2.0 interface
• Portable service tool for IQRF network management
• EEPROM memory
• 3 pushbuttons
• Piezo buzzer
• IQRF transceiver module
• On-board PCB antenna
• Backup accumulator
• Very low power consumption in Sleep mode
Block schematics
&copy; 2010 MICRORISC s.r.o.
www.iqrf.org
MNGWUSB13_100726
Page 2
GW-USB-13
Electrical specifications
(typical values unless otherwise stated)
Power supply
Accumulator
Display
USB
5.0 &plusmn; 0.35 V DC
LIP-552240 (Li-Pol 3.7 V, 400 mAh)
OLED 1“, 96 x 64 pixels, white
V2.0 Compliant SIE
Supply current
operational
standby
accumulator charging
18 mA to 35 mA, 25 mA 1 typical (depends on display contrast and
number of active pixels)
11 &micro;A 2
85 mA
Temperature range
0 &deg;C to +70 &deg;C
Frequency range
RF output power
Supported TR modules
Antenna
868 MHz or 916 MHz (SW selectable)
1.3 mW
TR-52B and highers, without integrated antenna
PCB antenna on the GW board.
It must be connected (soldered) by the user.
Dimensions
93 mm x 42 mm x 14 mm
Weight
42 g 3
Note 1: This current is increased due to charging in case of external supply (depended on the accumulator state).
Note 2: All peripherals shut down.
Note 3: Including accumulator and TR module.
Absolute maximum ratings
Stresses above those values may cause permanent damage to the device. Exposure to maximum rating conditions
for extended periods may affect device reliability.
Supply voltage (VCC)
Storage temperature
&copy; 2010 MICRORISC s.r.o.
5.5 V
-40 &deg;C to +85 &deg;C
www.iqrf.org
MNGWUSB13_100726
Page 3
GW-USB-13
Hardware
GW-USB-13 is a generic equipment, i.e. the hardware is fixed and the user can realize specific functionality by
software only. Detailed information for designers is available in the DS-PAGER development set.
Power supply
GW-USB-13 is intended to be supplied via micro USB connector, either from PC or from the adapter. The
accumulator serves as a backup for external power source and should be charged from it.
Sleep mode
It is possible to switch off all functions and peripherals for current consumption minimizing, especially in idle or while
supplied from the accumulator. GW power is not switched off, the Sleep mode is used instead of this.
EEPROM memory
Capacity: 64 kb, serial interface SPI (shared with the TR module), 1 000 000 erase/write cycles (typ.).
Pushbuttons
Functionality of all three pushbuttons is fully under software control.
Beeper
The functionality is fully under software control.
TR module
The transceiver module is inserted in SIM card connector. User program should be uploaded by an external
programmer outside the GW or inside the GW using RF PGM wireless upload (RF PGM should be enabled in
external programmer first) – see the AN009 Application note.
Antenna
GW uses the built-in PCB antenna module board.
Caution: To enable TR removal, the GW is delivered with TR module not connected to the antenna. It should be
soldered by the user before usage.
Case
The plastic case is limited to a very few number of open/close cycles only.
Tip: The TR module can be uploaded via RF PGM with the case closed.
Interfaces and connectors
interface
pins
connector type
USB
5
Micro USB
Accumulator
2
Soldering stripes
Charger
2
Via Micro USB connector
TR module
8
1
SIM connector
Through hole soldering for antenna connection
Software
GW-USB-13 software should be developed with the DS-PAGER development set. Detailed information for designers
is delivered with it.
&copy; 2010 MICRORISC s.r.o.
www.iqrf.org
MNGWUSB13_100726
Page 4
GW-USB-13
Pack list
• GW-USB-13 with Demo application programmed (in Sleep mode)
• TR-52B with E07-SPI example programmed, inserted in SIM connector, not connected to the antenna, switching to
the RF PGM after reset disabled
• Accumulator (soldered)
• Micro USB cable
Ordering codes
• GW-USB-13
Gateway GW-USB-13, 868 MHz as well as 916 MHz
Recommended options
• DS-PAGER
Development set for GW-USB-13
• MI-TI-A6-microUSB
Wall adapter for charging from mains.
Document history
• 100726
• 090825
• 090626
• 090514
&copy; 2010 MICRORISC s.r.o.
Revised, TR-52B inside. Related development set renamed to DS-PAGER.
Related development set renamed to DK-GW-USB-13-xxx.
Just visual aspects improved
First release
www.iqrf.org
MNGWUSB13_100726
Page 5
GW-USB-13
Sales and Service
Corporate office
MICRORISC s.r.o., Delnicka 222, 506 01 Jicin, Czech Republic, EU
Tel: +420 493 538 125, Fax: +420 493 538 126, www.microrisc.com
Partners and distribution
Please visit www.iqrf.org/partners
Quality management
ISO 9001 : 2000 certified
Complies with ETSI directives EN 30279 V.1.2.1:99, ETS 30683:97, ETSI EN 301489-1:00,
ETSI EN 300220-1:00, ETSI EN 300390-2V.1.1.1:00
Complies with FCC directives FCC CFR, Title 47, Part 15, Section 15.209, FCC CFR, Title 47, Part 15, Section 15.249
Complies with Directive 2002/95/EC (RoHS)
Trademarks
The IQRF name and logo are registered trademarks of MICRORISC s.r.o.
PIC, SPI, Microchip, RFM and all other trademarks mentioned herein are property of their respective owners.
Legal
All information contained in this publication is intended through suggestion only and may be superseded by updates
without prior notice. No representation or warranty is given and no liability is assumed by MICRORISC s.r.o. with respect to
the accuracy or use of such information.
Without written permission it is not allowed to copy or reproduce this information, even partially.
No licenses are conveyed, implicitly or otherwise, under any intellectual property rights.
The IQRF products utilize several patents (CZ, EU, US)
On-line support: http://iq-esupport.com
&copy; 2010 MICRORISC s.r.o.
www.iqrf.org
MNGWUSB13_100726
Page 6
">

Hello! I am an AI chatbot specifically trained to assist you with the MICRORISC GW-USB-13 IQRF USB Gateway User's Guide. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Show related prompts

Assistant typing

Assistant terminated

Key features

USB v2.0 interface
OLED display
8b microcontroller
EEPROM memory
IQRF transceiver module
Backup accumulator
Very low power consumption in Sleep mode

Frequently asked questions

The GW-USB-13 is an IQRF gateway with USB connectivity and an OLED display. It provides an interface between a USB port and an IQRF network.

The GW-USB-13 has a variety of applications, including home automation, portable controllers, pagers, and diagnostic tools. It can also be used as a portable service tool for IQRF network management.

The GW-USB-13 is typically powered via a micro USB connector, either from a PC or an adapter. The on-board accumulator provides backup power and can be charged from the external power source.

The GW-USB-13 uses a built-in PCB antenna module board. This antenna must be soldered by the user before the device can be used.

The GW-USB-13 software is developed using the DS-PAGER development set, which includes detailed information for designers.