Regency Fireplace Products | HZ42E-NG | Installation manual | Regency Fireplace Products HZ42E-NG Installation manual

Regency Horizon™ HZ42E
Gas Fireplace
Owners &
Installation Manual
MODELS:
HZ42E-NG Natural Gas
HZ42E-LP Propane
www.regency-fire.com
WARNING:
FOR YOUR SAFETY
If the information in these instructions are not followed exactly, What to do if you smell gas:
a fire or explosion may result causing property damage,
Do not try to light any appliance
Do not touch any electrical switch:
personal injury or loss of life.
do not use any phone in your
FOR YOUR SAFETY
building.
Do not store or use gasoline or other flammable vapors and
Immediately call your gas supplier
liquids in the vicinity of this or any other appliance.
from a neighbour's phone. Follow
the gas supplier's instructions.
Installation and service must be performed by a qualified
If you cannot reach your gas
installer, service agency or the gas supplier.
supplier, call the fire department.
Tested by:
Installer: Please complete the details on the back cover
Installer:
and leave this manual with the homeowner.
Homeowner: Please keep these instructions for future reference.
918-932
FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4
06/25/13
To the New Owner:
Congratulations!
You are the owner of a state-of-the-art Gas Fireplace by REGENCY®. The HZ42E has been
designed to provide you with all the warmth and charm of a fireplace at the flick of a switch. The
model HZ42E has been approved by Warnock Hersey/Intertek for both safety and efficiency. As
it also bears our own mark, it promises to provide you with economy, comfort and security for
many trouble free years to follow. Please take a moment now to acquaint yourself with these
instructions and the many features of your Regency® Fireplace.
Regency Horizon
Gas Inserts Benefits Video
2
HZ42E Regency Horizon™ Gas Fireplace
MANUFACTURED MOBILE HOME REQUIREMENTS
INFORMATION FOR MOBILE/MANUFACTURED HOMES AFTER FIRST SALE
This Regency® product has been tested and listed by Warnock Hersey/Intertek as a Direct Vent Wall Furnace to the following standards:
VENTED GAS FIREPLACE HEATERS ANSI Z21.88a-2007 / CSA 2.33a-2007 and GAS-FIRED APPLIANCES FOR USE AT HIGH ALTITUDES
CAN / CGA 2.17-M91.
This Direct Vent System Appliance must be installed in accordance with the manufacturer's installation instructions and the Manufactured
Home Construction and Safety Standard, Title 24 CFR, Part 3280, or the current Standard of Fire Safety Criteria for Manufactured Home
Installations, Sites, and Communities ANSI/NFPA 501A, and with CAN/CSA Z240-MH Mobile Home Standard in Canada.
This appliance installation must comply with the manufacturer's installation instructions and local codes, if any. In the absence of local codes
follow the current National Fuel Gas Code, ANSI Z223.1 and the current National Electrical Code ANSI/NFPA 70 in the U.S.A., and the current
CAN/CGA B149 Gas Installation Code and the current Canadian Electrical Code CSA C22.1 in Canada.
This appliance comes equipped with a dedicated #8 Ground Lug for attachment of the ground wire to the steel chassis as applicable to
local codes.
The appliance, when installed, must be electrically grounded in accordance with local codes or, in the absence of local codes, with the
National Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.1.
This appliance may only be installed in an aftermarket permanently located, manufactured (U.S.A only) or mobile home, where not prohibited
by local codes.
This appliance can only be used with the type of gas indicated on the rating plate. This appliance is not convertible for use with other gases.
Ensure that structural members are not cut or weakened during installation.
HZ42E Regency Horizon™ Gas Fireplace
3
TABLE OF CONTENTS
SAFETY LABEL
Copy of Safety Decal .....................................................5
REQUIREMENTS
MA Code - CO Detector.................................................6
DIMENSIONS
Unit Dimensions ............................................................7
Pilot Adjustment ...........................................................34
Gas Pipe Pressure Testing ..........................................34
886 S.I.T. Valve Description.........................................34
Aeration Adjustment ....................................................34
Wiring Diagram ............................................................35
optional accent lighting Wiring Diagram .....................36
Optional Wall Thermostat ...........................................38
Optional Remote Control .............................................38
Gt /GTm remote features.............................................38
Wall Switch ..................................................................38
GT remote installation .................................................39
GTM remote installation ..............................................40
Optional Reflective Panel Installation ..........................42
Optional Light Installation ............................................43
Glass Crystals or optional stones ................................46
Installation On Burner ..................................................46
Glass door Installation .................................................48
Faceplate Installation..................................................49
INSTALLATION
Important Message ......................................................8
Before You Start ............................................................8
General Safety Information............................................8
Installation Checklist ......................................................9
Locating Your Gas Fireplace .........................................9
Clearances ..................................................................10
Mantel Clearances....................................................... 11
Mantel Leg Clearances................................................ 11
Unit Assembly Prior To Installation ..............................12
Standoff Assembly ...............................................12
Nailing Strips........................................................12
Framing Dimensions....................................................13
Non-Combustible Requirements .................................14
non-combustible facing installation .............................14
Framing & Finishing.....................................................15
Vent Restrictor Position ...............................................17
Exterior Vent Termination Requirements .....................18
4” x 6-5/8” Rigid Pipe ..................................................19
Cross Reference Chart only ........................................19
Venting Introduction .....................................................21
Venting Arrangement for Horizontal Terminations .......21
Horizontal Terminations ...............................................22
Flex Vent 4" x 6-5/8" ....................................................22
Horizontal terminations ................................................23
Rigid Pipe 4" x 6-5/8"...................................................23
Horizontal Terminations ...............................................24
Rigid Pipe 4" x 6-5/8"...................................................24
Venting Arrangement for Vertical Terminations............27
Rigid Pipe 4" x 6-5/8" Vertical Terminations ................29
Rigid Pipe 4" x 6-5/8"...................................................29
Unit Installation with Horizontal Termination ...............31
4" x 6-5/8"venting ........................................................31
Unit Installation with Horizontal Termination ...............32
Unit installation with Vertical Termination ....................33
4" x 6-5/8" venting .......................................................33
High Elevation Gas Line Installation ............................34
4
OPERATING INSTRUCTIONS
Operating Instructions .................................................51
First Fire ......................................................................51
Lighting Procedure ......................................................51
Shutdown Procedure ...................................................51
Normal Operating Sounds of Gas Appliances .............51
Copy of Lighting Plate Instructions ..............................52
Maintenance Instructions.............................................53
General Vent Maintenance ..........................................53
Glass Gasket ...............................................................53
Glass Door...................................................................53
Glass Replacement .............................................53
Glass Door Removal ...................................................54
Valve assembly Replacement .....................................55
Bulb replacement.........................................................56
PARTS LIST
Main Assembly ............................................................57
WARRANTY
The Warranty: Limited Lifetime ...................................59
HZ42E Regency Horizon™ Gas Fireplace
SAFETY LABEL
This is a copy of the label that accompanies each HZ42E-NG and HZ42E-LP Direct Vent Gas Fireplace. We have printed a copy of the contents here for
your review.
NOTE: Regency® units are constantly being improved. Check the label on the unit and if there is a difference, the label on the unit is the correct one.
COPY OF SAFETY DECAL
DO NOT REMOVE THIS LABEL / NE PAS ENLEVER CETTE ÉTIQUETTE
Listed: VENTED GAS FIREPLACE HEATER / FOYER AU GAZ À ÉVACUATION
Certified for/Certifiée pour: CANADA and U.S.A.
Serial No./ No de serie
Tested to: CAN/CGA-2.17-M91,ANSI Z21.88a-2007/CSA 2.33a-2007
4001172
371
MAY BE INSTALLED IN MANUFACTURED (MOBILE) HOMES AFTER FIRST SALE.
NATURAL GAS: Model HZ42E-NG
Minimum supply pressure
Manifold pressure high
Manifold pressure low
Orifice size
Minimum input
Maximum input
Altitude
5.0"
3.5"
1.6"
#40
17,500
26,000
0-4500
WC/C.E. (1.25kPa)
WC/C.E. (0.87kPa)
WC/C.E. (0.40kPa)
DMS
Btu/h (5.13 kW)
Btu/h (7.62 kW)
ft/pi
(0-1372 m)
APPAREIL FONCTIONNANT AU NATURAL GAS
CONCU POUR ETRE POELE: Modéle HZ42E
Pression d'allimentation minimum
Pression à la tubulure d'échappement élevée
Pression à la tubulure d'échappement basse
Grandeur de l'injecteur
Débit Calorifique minimum selon
Débit Calorifique maximum selon
l'altitude
Minimum Clearances to Combustibles /
Degagement Minimum De Materiaux Combustibles
B
D
F
A
C
E
PROPANE GAS: Model HZ42E-LP
Minimum supply pressure
Manifold pressure high
Manifold pressure low
Orifice size
Minimum input
Maximum input
Altitude
12“ WC
(2.98 kpa)
10"
WC/C.E. (2..49kPa)
WC/C.E. (1.60kPa)
6.4"
#53
DMS
19,500 Btu/h (5.71 kW)
24,500 Btu/h (7.18 kW)
0-4500 ft/pi
(0-1372 m)
ÉQUIPÉ A L'UISINE POUR GAZ PROPANE
CONCU POUR ETRE POELE: Modéle HZ42E
Pression d'allimentation minimum
Pression à la tubulure d'échappement élevée
Pression à la tubulure d'échappement basse
Grandeur de l'injecteur
Débit Calorifique minimum selon
Débit Calorifique maximum selon
l'altitude
Side Walls
A
8” (203mm)
Ceiling
B
22” (559mm)
Min. Mantel Height
C
13" (330mm)
Max. Mantel Depth
D
13” (330mm)
Alcove Width
E
84" (2133mm)
Alcove Depth
F
36" (914mm)
DOOR SEAL: Please
check that the door is
properly sealed
(See Instruction Manual for
detailed instructions)
This appliance must be installed in accordance with local codes, if any; if none, follow the National Fuel Gas Code, ANSI Z223.1, or Natural Gas and Propane Installation Code, CSA B149.1.
This appliance must be installed in accordance with the Standard CAN/CSA Z240 MH, Mobile Housing, in Canada, or with the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280, in
the United States, or when such a standard is not applicable, ANSI/NCSBCS A225.1/NFPA 501A, Manufactured Home Installations Standard or ANSI A119.2 ou NFPA 501C Standard for Recreational Vehicles
This appliance is only for use with the type of gas indicated on the rating plate and may be installed in an aftermarket, permanently located, manufactured (mobile) home where not prohibited by local codes. See
owner's manual for details.
Installer l'appareil selon les codes ou règlements locaux, ou, en l'absence de tels règlements, selon les codes d'installation ANSI Z223.1, National Fuel Gas Code ou CSA-B149.1 en vigueur.
Installer l'appareil selon la norme CAN/CSA-Z240, Série MM, Maison mobiles ou CAN/CSA-Z240 VC, Véhicules de camping, ou la norme 24 CFR Part 3280, Manufactured Home Construction and Safety
Standard. Si ces normes ne sont pas pertinentes, utilisez la norme ANSI/NCSBCS A225.1/NFPA 501A, Manufactured Home Installations Standard, ou ANSI A119.2 ou NFPA 501C Standard for Recreational
Vehicles.
Cet appareil doit être utilize uniquement avec le type de gaz indiqué sur la plaque signalétique. Cet appareil peut être installé dans une maison préfabriquée ou mobile (É.-U. seulement) installée à demeure si
les règlements locaux le permettent. Voir la notice de l'utilisateur pour plus de renseignements. Cet appareil ne peut pas être utilisé avec d'autres gaz sauf si une trousse de conversion certifiée est fournie.
This vented gas fireplace heater is not for use with air filters.
Ne pas utiliser de filtre à air avec ce foyer au gaz à évacuation.
POUR UTILISATION UNIQUEMENT AVEC LES PORTES EN VERRE CERTIFIÉES AVEC L'APPAREIL
FOR USE WITH GLASS DOORS CERTIFIED WITH THE APPLIANCE ONLY
Electrical supply / Électrique 115VAC, 1.13 A, 60Hz.
NOT FOR USE WITH SOLID FUELS. / NE PAS UTILISER AVEC DU COMBUSTIBLE SOLIDE.
FPI Fireplace Products International Ltd. Delta, BC, Canada
Made in Canada/ Fabrique au Canada
918-931
For the State of Massachusetts, installation
and repair must be done by a plumber or
gasfitter licensed in the Commonwealth of
Massachusetts.
For the State of Massachusetts, flexible connectors shall not exceed 36 inches in length.
For the State of Massachusetts, the appliances individual manual shut-off must be a
t-handle type valve.
The State of Massachusetts requires the
installation of a carbon monoxide alarm in
accordance with NFPA 720 and a CO alarm
with battery back up in the same room where
the gas appliance is installed.
HZ42E Regency Horizon™ Gas Fireplace
5
REQUIREMENTS
MA Code - CO Detector
(for the State of Massachusetts only)
5.08: Modifications to NFPA-54, Chapter 10
(2) Revise 10.8.3 by adding the following additional requirements:
(a) For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for
residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than
seven (7) feet above finished grade in the area of the venting, including but not limited to decks and porches, the following requirements shall
be satisfied:
1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time of installation of the side wall horizontal vented gas fueled
equipment, the installing plumber or gasfitter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-up is
installed on the floor level where the gas equipment is to be installed. In addition, the installing plumber or gasfitter shall observe that a battery
operated or hard wired carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure
served by the side wall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to secure the services of
qualified licensed professionals for the installation of hard wired carbon monoxide detectors
a. In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard wired carbon
monoxide detector with alarm and battery back-up may be installed on the next adjacent floor level.
b. In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall have a period of
thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon
monoxide detector with an alarm shall be installed.
2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon monoxide detector as required in accordance with the above provisions
shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS certified.
3. SIGNAGE. A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight
(8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The
sign shall read, in print size no less than one-half (1/2) inch in size, "GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL
OBSTRUCTIONS".
4. INSPECTION. The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation
unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR
5.08(2)(a)1 through 4.
(b) EXEMPTIONS: The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4:
1. The equipment listed in Chapter 10 entitled "Equipment Not Required To Be Vented" in the most current edition of NFPA 54 as adopted by
the Board; and
2. Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the dwelling, building or
structure used in whole or in part for residential purposes.
(c) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM PROVIDED. When the manufacturer of Product
Approved side wall horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the
instructions provided by the manufacturer for installation of the equipment and the venting system shall include:
1. Detailed instructions for the installation of the venting system design or the venting system components; and
2. A complete parts list for the venting system design or venting system.
(d) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED. When the manufacturer of a
Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the flue gases, but identifies
"special venting systems", the following requirements shall be satisfied by the manufacturer:
1. The referenced "special venting system" instructions shall be included with the appliance or equipment installation instructions; and
2. The "special venting systems" shall be Product Approved by the Board, and the instructions for that system shall include a parts list and
detailed installation instructions.
(e) A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions,
all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of
the installation.
6
HZ42E Regency Horizon™ Gas Fireplace
DIMENSIONS
UNIT DIMENSIONS
47” (1194mm)
18-5/8” (473mm)
15-5/8” (397mm)
½” (13mm)
1-½” (38mm)
41-3/16”” (1046mm)
1-½” (38mm)
28-7/8” (733mm)
21-3/16” (538mm)
½” (13mm)
23-5/8” (600mm)
12-7/8” (327mm)
36” (914mm)
36-7/8” (937mm)
30” (762mm)
38”” (965mm)
14-5/32” (360mm)
48-3/4” (1238mm)
HZ42E Regency Horizon™ Gas Fireplace
7
INSTALLATION
IMPORTANT MESSAGE
SAVE THESE
INSTRUCTIONS
The HZ42E Direct Vent Fireplace must be installed
in accordance with these instructions. Carefully read
all the instructions in this manual first. Consult the
"authority having jurisdiction" to determine the need
for a permit prior to starting the installation. It is the
responsibility of the installer to ensure this fireplace
is installed in compliance with manufacturers
instructions and all applicable codes.
BEFORE YOU START
Safe installation and operation of this appliance
requires common sense, however, we are required
by the Canadian Safety Standards and ANSI
Standards to make you aware of the following:
INSTALLATION AND REPAIR SHOULD
BE DONE BY AN AUTHORIZED
SERVICE PERSON. THE APPLIANCE
SHOULD BE INSPECTED BEFORE
USE AND AT LEAST ANNUALLY BY A
PROFESSIONAL SERVICE PERSON.
MORE FREQUENT CLEANING MAY
BE REQUIRED DUE TO EXCESSIVE
LINT FROM CARPETING, BEDDING
MATERIAL, ETC. IT IS IMPERATIVETHAT
CONTROL COMPARTMENTS, BURNERS
AND CIRCULATING AIR PASSAGEWAYS
OF THE APPLIANCE BE KEPT CLEAN.
DUE TO HIGH TEMPERATURES, THE
APPLIANCE SHOULD BE LOCATED
OUT OF TRAFFIC AND AWAY FROM
FURNITURE AND DRAPERIES.
WARNING: FAILURE TO INSTALL THIS
APPLIANCE CORRECTLY WILL VOID
YOUR WARRANTY AND MAY CAUSE A
SERIOUS HOUSE FIRE.
CHILDREN AND ADULTS SHOULD BE
ALERTED TO THE HAZARDS OF HIGH
SURFACE TEMPERATURES, ESPECIALLY THE FIREPLACE GLASS, AND
SHOULD STAY AWAY TO AVOID BURNS
OR CLOTHING IGNITION.
YOUNG CHILDREN SHOULD BE CAREFULLY SUPERVISED WHEN THEY ARE
IN THE SAME AREA AS THE APPLIANCE. TODDLERS, YOUNG CHILDREN
AND OTHERS MAY BE SUSCEPTIBLE
TO ACCIDENTAL CONTACT BURNS. A
PHYSICAL BARRIERS IS RECOMMENDED IF THERE ARE AT RISK INDIVIDUAL
IN THE HOUSE. TO RESTRICT ACCESS
TO A FIREPLACE OR STOVE, INSTALL
AN ADJUSTABLE SAFETY GATE TO
KEEP TODDLERS, YOUNG CHILDREN
AND OTHER AT RISK INDIVIDUALS OUT
OF THE ROOM AND AWAY FROM HOT
SURFACES.
CLOTHING OR OTHER FLAMMABLE
MATERIAL SHOULD NOT BE PLACED
ON OR NEAR THE APPLIANCE.
GENERAL SAFETY
INFORMATION
10) Be aware of electrical wiring locations in walls
and ceilings when cutting holes for termination.
11) Under no circumstances should this appliance
be modified. Parts that have to be removed for
servicing should be replaced prior to operating
this appliance.
12) Installation and any repairs to this appliance
should be done by an authorized service person. A professional service person should be
called to inspect this appliance annually. Make
it a practice to have all of your gas appliances
checked annually.
13) Do not slam shut or strike the glass door.
14) Under no circumstances should any solid fuels
(wood, paper, cardboard, coal, etc.) be used
in this appliance.
15) The appliance area must be kept clear and
free of combustible materials, (gases and other
flammable vapours and liquids).
Emissions from burning wood or gas could
contain chemicals known to the State of
California to cause cancer, birth defects or
other reproductive harm.
1) The appliance installation must conform with
local codes or, in the absence of local codes,
with the current Canadian or National Gas
Codes, CAN1-B149 or ANSI Z223.1 Installation
Codes.
2) The appliance when installed, must be electrically grounded in accordance with local codes,
or in the absence of local codes with the current
National Electrical Code, ANSI/NFPA 70 or CSA
C22.1 Canadian Electrical Code.
3) See general construction and assembly instructions. The appliance and vent should be
enclosed.
4) This appliance must be connected to the specified vent and termination cap to the outside of
the building envelope. Never vent to another
room or inside a building. Make sure that the
vent is fitted as per Venting instructions.
5) Inspect the venting system annually for blockage and any signs of deterioration.
6) Venting terminals shall not be recessed into a
wall or siding.
7) Any safety glass removed for servicing must
be replaced prior to operating the appliance.
8) To prevent injury, do not allow anyone who is
unfamiliar with the operation to use the fireplace.
9) Wear gloves and safety glasses for protection
while doing required maintenance.
8
HZ42E Regency Horizon™ Gas Fireplace
INSTALLATION
INSTALLATION
CHECKLIST
1) Locate appliance
a) Room location (Refer to "Locating Your Gas
fireplace" section)
b) Clearances to Combustibles (Refer to
"Clearances" section)
c) Mantle Clearances (Refer to "Mantel
Clearances" section)
d) Framing & Finishing Requirements (Refer
to "Framing & Finishing" section)
e) Venting Requirements (Refer to "Venting"
section)
This includes:
1) Clocking the appliance to ensure the correct
firing rate (rate noted on label 26,000 Btu/h
(NG), 24,500 Btu/h (LP) after burning appliance
for 15 minutes.
4) This appliance is Listed for bedroom installations
using the standard Remote (millivolt thermostat
system). Some areas may have further
requirements, check local codes before
installation.
2) If required, adjusting the primary air to ensure
that the flame does not carbon. First allow the
unit to burn for 15-20 min. to stabilize.
5) The HZ42E Direct Vent Gas Fireplace
is approved for alcove installations, see
"Clearances" section for details.
CAUTION: Any alteration to the product that
causes sooting or carboning that results in damage is not the responsibility of the manufacturer.
6) We recommend that you plan your installation on
paper using exact measurements for clearances
and floor protection before actually installing this
appliance. Have an authorized inspector, dealer,
or installer review your plans before installation.
2) Assemble Standoffs (Refer to "Unit Assembly
Prior to Installation).
Note: For vent terminations refer to "Exterior
Vent Termination Locations" section.
3) Slide unit into place.
LOCATING YOUR
GAS FIREPLACE
4) Install vent (Refer to "Venting Arrangement"
sections).
5) Make gas connections (Refer to "Gas Line
Installation section).
6) Make electrical connections to receptacle
supplied with unit (recommended).
7) Test the pilot (Refer to "Pilot Adjustment"
section).
8) Test Gas Pressure (Refer to "Gas Pipe Pressure
Testing" section).
9) Install standard and optional features. Refer to
the following sections:
a)
b)
c)
d)
e)
f)
g)
1) When selecting a location for your fireplace,
ensure that the clearances are met.
2) The appliance must be installed on a flat, solid,
continuous surface For example a wood, metal
or concrete floor or in a raised (on the wall) application. The appliance must be installed on
a metal or wood panel extending the full width
and depth of the appliance.
3) The HZ42E Direct Vent Gas Fireplace can be
installed in a recessed position or framed out
into the room as in A, B, C and D.
See Diagram 1.
Glass Crystals/ Optional Ceramic
Stones
Optional Firebox Base Pebbles
Optional Reflective Panels
Optional Accent Light
Faceplate
Remote Control or Wall Thermostat
Optional AC Power Adaptor
10) Wall Mounted ON/OFF Switch:
Use the toggle wall switch supplied with the
manual package. Use of a “decor” switch causes
higher resistance which is a problem on gas
fireplaces.
Diagram 1
11) Final check.
Before leaving this unit with the customer, the
installer must ensure that the appliance is firing
correctly and operation fully explained to
customer.
HZ42E Regency Horizon™ Gas Fireplace
A)
B)
C)
D)
Flat on Wall
Flat on Wall Corner
Recessed into Wall/Alcove
Corner
9
INSTALLATION
CLEARANCES
The clearances listed below are Minimum distances unless otherwise stated:
A major cause of chimney related fires is failure to maintain required clearances (air space) to combustible materials. It is of the greatest importance
that this fireplace and vent system be installed only in accordance with these instructions.
Caution Requirements
The top, back and sides of the fireplace are defined by
standoffs. The metal ends of the standoff may NOT be
recessed into combustible construction.
WARNING
Fire hazard is an extreme risk
if these clearances (air space) to combustible materials are not
adhered to. It is of greatest importance that this fireplace and vent
system be installed only in accordance with these instructions.
Clearance:
Dimension
A: Mantel Height (min.)
13" (330mm)
Top of Fireplace Opening
B: Sidewall (on one side)
8" (203mm)
Side of Fireplace Opening
C: Ceiling
(room and/or alcove)
22" (559mm)
Top of Fireplace Opening
D: Mantel Depth (max.)
13" (330mm)
22" Above Fireplace Opening
E: Alcove Width
84" (2134mm)
Sidewall to Sidewall (Minimum)
F: Alcove Depth
36" (914mm)
Front to Back Wall (Maximum)
G: From Floor
Measured From:
25-3/4"
Top of Fireplace Opening
0"
No hearth required
Note:
Flue Clearances to Combustibles
Horizontal - Top
Horiztonal - Side
Horiztonal - Bottom
Vertical
Passing through wall/
floor/ceiling - when
firestop is used.
3"
2"
2"
2"
1-1/2"
Installed close
to ceiling.
E
IMPORTANT NOTE
Combustible material can only be installed to
the bottom lip of the fireplace as shown below.
The finished floor must not come in contact with
the front face of the fireplace. Non-combustible
material (see "Framing and Finishing" section)
must act as a barrier between the front face and
finished floor.
F
Alcove
10
HZ42E Regency Horizon™ Gas Fireplace
INSTALLATION
MANTEL CLEARANCES
14 12 10 8
6
4
2
0
Due to the extreme heat this fireplace emits, the
mantel clearances are critical. Combustible mantel
clearances from top of front facing are shown in the
diagram on the right.
26
12" (305mm)
Note: Ensure the paint that is used on the mantel
and the facing is "High Quality" or the paint
may discolour.
Combustible Material
20
21-1/2”
1" (25mm)
10
13”
0
To Unit
Base 25-3/4”
Metal Stud
(On Edge)
Non-combustible
Facing
Standoff
Top of
Fireplace
Opening
MANTEL LEG CLEARANCES
Combustible mantel leg clearances as per diagram:
3-7/8”(98mm)
MANTEL LEG
7”
4"
Non-Combustible
Allowable mantel
leg projection
1.5" (38mm)
5-1/2” (140mm)
8” (203mm)
11” (279mm)
HZ42E Regency Horizon™ Gas Fireplace
11
INSTALLATION
UNIT ASSEMBLY
PRIOR TO
INSTALLATION
The Nailing Strips and the 2 Standoffs must be correctly positioned and attached
before unit is slid into position.
NAILING STRIPS
The nailing strips come attached to the unit. There is 1 plate on each side,
1 on the top, and one on the bottom that can be folded out as required.
The top and side nailing strips are secured to the framing. The bottom
nailing strip is secured to the unfinished floor - if installing the unit directly
on the floor.
STANDOFF ASSEMBLY
The standoffs are shipped in a flat position and must be folded into shape and
attached.
1) Remove the standoffs from the fireplace.
2) Take each standoff and bend into the correct shape. Bend up at the bend lines
until the screw holes in the standoff and the pre-punched screw holes on the
fireplace top line up.
3) Attach the standoff securely to the unit with 2 screws per standoff (on opposite
corners).
Nailing Strips
Standoff
Nailing Strips shown folded out.
IMPORTANT NOTE
Framing depth measurement is noted with the
nailing strips set as far forward on the firebox
as possible. The nailing strips can be adjusted
back up to 1” to allow for varying thicknesses
in non-combustible material & wall finishes.
12
HZ42E Regency Horizon™ Gas Fireplace
INSTALLATION
FRAMING DIMENSIONS
Framing
Dimensions
Description
A
B
Framing Height
Framing Width
C*
Framing Depth*
D
E
F
G
H
I
J
K
Minimum Height to Combustibles
Corner Wall Depth
Corner Facing Wall Width
Vent Centerline Height
Non-combustible facing height
Gas Connection Opening Height
Gas Connection Height
Gas Connection Inset
L
Gas Connection Opening Width
HZ42E
37-1/4” (946mm)
47 - 1/2" (1207mm)
C1 Horizontal Vent 18 - 3/4" (476mm)
C2 Vertical Vent 22" (559mm)
Vertical rise -terminating horizontal
39 - 9/16" (1004mm)
51 - 1/2" (1308)
72 - 7/8" (1851mm)
33 - 1/4" (845mm)
13” (330mm)
2" (51mm)
4 - 1/2" (114mm)
2 - 7/8" (73mm)
4 - 5/8" (117mm)
* Framing depth measurement is noted with the nailing strips set as far forward on the firebox as possible.
The nailing strips can be adjusted back up to 1” to allow for varying thicknesses in non-combustible
material & wall finishes.
Drywall or
other facing
Metal Stud (Header)
H
Note: All other framing may
be of wood construction.
Metal Stud
on edge
A
G
Flex or Rigid Pipe
Non-Combustible
Facing
C1
B
C
Finished Floor
D
E
C2
I
J
F
HZ42E Regency Horizon™ Gas Fireplace
K
L
13
INSTALLATION
NON-COMBUSTIBLE REQUIREMENTS
All four pieces (top, 2 sides, bottom) are now supplied to meet the non combustible requirements. Previously only the top was supplied
Metal Stud
Metal Stud
16"
(406mm)
4-3/8"
(111mm)
34 -1/4" (870mm)
Non-combustible
Note: Calcium Silicate is 1/2' thick
41-3/8”
21-1/2”
18-3/4”
(467mm)
If finishing the wall above the unit with materials
such as tile, brick, marble, etc. non-combustible
board available from the building supply store
can be used.
Non-combustible
Material
(supplied with unit)
Non-combustible
Calcium silicate board is a high - grade material
with cement, quartz, natural and selected
minerals as the main raw materials. It is widely
used for partitions and ceilings in buildings.
It is fire proof and earthquake proof.
Metal Stud (header)
on edge
48-7/8" (1241mm)
Non-combustible
3-5/8"
(92mm)
NON-COMBUSTIBLE FACING INSTALLATION
Caution: The non-combustible board supplied with this unit can
be damaged if dropped or struck. Handle with care.
1) Using drywall screws - secure non combustible material
around unit, framing and top nailing strip every 6 inches.
Important Note: To avoid cracking the board - pre-drill holes prior to
securing to unit/ framing.
2) Wipe any debris/dust from the non combustible
material and drywall.
3) Prior to securing it is mandatory to prime the facing and edges
using a quality primer. This will ensure proper adhesion of both the
tape and mud. The supplied board is very porous.
Failure to follow this procedure will result in cracked seams.
Non-combustible board
shipped with unit.
Non-combustible board
shipped with unit.
4) Tape the seams using a mesh type tape.
5) Mud seams as normal. We recommend using a
product called Durabond high strength compound - for the first coat.
This product can be found at any hardware store.
Mud must be cured as per manufacturer’s recommendations.
6) Prime wall for a second time for proper adhesion of paint
7) Paint walls using a high quality paint which will withstand
the high temperatures being emitted from this appliance.
14
Non-combustible board-faces and edges
MUST BE PRIMED.
HZ42E Regency Horizon™ Gas Fireplace
INSTALLATION
FRAMING & FINISHING
1) Frame in the enclosure for the unit with framing material.
IMPORTANT: The framed opening must be of non-combustible
material.
Note: When constructing the framed opening, please ensure there
is access to install the gas lines when the unit is installed.
5) If material such as brick, stone, etc extends past the faceplate depth (1-1/2"),
when finishing around the faceplate, the minimum opening dimensions noted
below must be adhered to ensuring for the removal of the faceplate and for
the safe operation of this appliance.
2) For exterior walls, insulate the enclosure to the same degree as the
rest of the house, apply vapour barrier and drywall, as per local installation codes. (Do not insulate the fireplace itself.)
WARNING: Failure to insulate and add vapor barriers to the inside
of the exterior wall will result in operational and performance
problems including, but not limited to: excessive condensation
on glass doors, poor flame package, carbon, blue flames etc.
These are not product related issues.
3) The unit does not have to be completely enclosed in a chase. You
must maintain clearances from the vent to combustible materials: See
"Clearances" section. Combustible materials can be laid against the
side and back standoffs and the stove base.
4) Non-combustible material (ie. tile, slate, etc) may be brought up to and
overlap the unit (top and bottom) ensuring that the maximum thickness
does not go beyond the 1-1/2" as shown in the diagram below. The
faceplate will not be able to be mounted if finished material is beyond
1-1/2".
6) For material such as brick, stone, etc that extends less than 1-1/2" , the
minimum opening dimensions noted below must be adhered, when finishing around the faceplate. This is to ensure the removal of the faceplate and
for the safe operation of this appliance.
21-1/2”
41-3/8”
Unit shown without faceplate
1/2" required
between faceplate
+ finished wall
HZ42E Regency Horizon™ Gas Fireplace
15
INSTALLATION
Note:
Depending on the material used for finishing, the nailing strips must be set accordingly so that the finished material is always at the 1-1/2" edge of the flange.
Finished
Material
Nailing Strip
Position
1/2"
1"
Nailing Strip
1” Forward
Unit
1"
1/2"
Nailing Strip
½” Forward
Unit
1-1/2"
0" (flush)
Nailing Strip
Flush w/unit
Factory Set
Unit
16
HZ42E Regency Horizon™ Gas Fireplace
INSTALLATION
VENT RESTRICTOR POSITION
Vent restriction is required for certain venting installations, see the diagrams in the "Venting
Arrangements" section to determine if they are required for your installation.
The Vent Restrictor plate is located on the inside top of the firebox.
To set the vent restriction as indicated in the venting arrangements diagrams, refer to the following instructions;
1) Remove the glass door - see instructions in this manual.
2) Remove the screws that hold the vent restrictor plate in place.
3) Adjust the vent restrictor plate to the required vent restrictor position as per the diagrams shown.
4) Once the vent restrictor plate is in the required position, secure with screws.
SET 0
THIS HOLE SETS THE
VENT RESTRICTOR
AT 2”
2”
Vent Restrictor Set 0
Factory Set Vent Restrictor
(no adjustment required)
SET 1
THIS HOLE SETS THE
VENT RESTRICTOR
AT 1-1/2”
1-1/2”
SET 2
THIS HOLE SETS THE
VENT RESTRICTOR
AT 1”
Vent Restrictor Set 1
1”
Vent Restrictor Set 2
HZ42E Regency Horizon™ Gas Fireplace
17
INSTALLATION
EXTERIOR VENT TERMINATION REQUIREMENTS
Minimum Clearance Requirements
Canada1
USA2
A
Clearance above grade, veranda, porch, deck, or balcony
12"(30cm)
12"(30cm)
B
Clearance to window or door that may be opened
12"(30cm)
9" (23cm)
C
Clearance to permanently closed window
*
*
D
Vertical clearance to ventilated soffit located above the terminal within a horizontal distance of 2 feet (61cm)
from the center line of the terminal (check with the local code)
19"(48cm)
19"(48cm)
E
Clearance to unventilated soffit
19"(48cm)
19"(48cm)
F
Clearance to outside corner: with AstroCap Termination Cap.
7"(18cm)
7"(18cm)
Clearance to outside corner: with all other approved Termination Caps.
13"(33cm)
13"(33cm)
Clearance to inside corner: with AstroCap Termination Cap
7"(18cm)
7"(18cm)
Clearance to inside corner: with all other approved Termination Caps.
13"(33cm)
G
H
Clearance to each side of center line extended above meter/regulator assembly
36"(90cm)
a
13"(33cm)
*
J
Clearance to service regulator vent outlet
36"(90cm)
*
K
Clearance to non-mechanical air supply inlet to building or the combustion air inlet to any other appliance
12"(30cm)
9" (23cm)
L
Clearance to a mechanical air supply inlet
#3' (91cm) above if within 10' (3m) horizontally.
72"(1.8m)
36"(90cm)b
M
Clearance above paved sidewalk or a paved driveway located on public property
84"(2.1m)┼
*
Clearance under veranda, porch, deck, or balcony
12"(30cm)‡
*
N
1
In accordance with current CSA B149.1, Natural Gas and Propane Installation Code
In accordance with the current ANSI Z223.1/NFPA 54, National Fuel Gas Code
A vent shall not terminate directly above a sidewalk or paved driveway which is located between two single family dwellings and serves both dwellings
‡ Permitted only if veranda, porch, deck, or balcony is fully open on a minimum of two sides beneath the floor
*a Clearance in accordance with local installation codes and the requirements of the gas supplier
3 feet (91cm) within a height of 15 feet (4.5m) above the meter / regulator assembly
b 3 feet (91cm) above - if within 10 feet (3m) horizontally
2
┼
18
HZ42E Regency Horizon™ Gas Fireplace
INSTALLATION
4” X 6-5/8” RIGID PIPE
CROSS REFERENCE CHART ONLY
Components from different Manufacturers may not be mixed. Not All Rigid Pipe components are available directly from FPI.
Description
Simpson
Selkirk
Direct Vent Pro®
Direct Temp™
American Metal
Products®
Metal-Fab™
Security
ICC Excel
Sure Seal
Secure- Vent®
Direct
Amerivent Direct
6” Pipe Length-Galvanized
46DVA-06
4DT-6
N/A
4D6
SV4L6
TC-4DL6
6” Pipe Length-Black
46DVA-06B
4DT-6B
N/A
4D6B
SV4LB6
TC-4DL6B
7” Pipe Length-Galvanized
N/A
N/A
4D7
N/A
N/A
N/A
7” Pipe Length-Black
N/A
N/A
4D7B
N/A
N/A
N/A
9” Pipe Length-Galvanized
46DVA-09
4DT-9
N/A
N/A
N/A
N/A
9” Pipe Length-Black
46DVA-09B
4DT-9B
N/A
N/A
N/A
N/A
12” Pipe Length-Galvanized
46DVA-12
4DT-12
4D12
4D12
SV4L12
TC-4DL1
TC-4DL1B
12” Pipe Length-Black
46DVA-12B
4DT-12B
4D12B
4D12B
SV4LB12
18” Pipe Length-Galvanized
46DVA-18
4DT-18
4D18
4D18
SV4LA
TC-4DL18
18” Pipe Length-Black
46DVA-18B
4DT-18B
4D18B
4D18B
SV4LA
TC-4DL18B
24” Pipe Length-Galvanized
46DVA-24
4DT-24
4D24
4D24
SV4L24
TC-4DL2
24” Pipe Length-Black
46DVA-24B
4DT-24B
4D24B
4D24B
SV4LB24
TC-4DL2B
36” Pipe Length-Galvanized
46DVA-36
4DT-36
4D36
4D36
SV4L36
TC-4DL3
36” Pipe Length-Black
46DVA-36B
4DT-36B
4D36B
4D36B
SV4LB36
TC-4DL3B
48” Pipe Length-Galvanized
46DVA-48
4DT-48
4D48
4D48
SV4L48
TC-4DL4
48” Pipe Length-Black
46DVA-48B
4DT-48B
4D48B
4D48B
SV4LB48
TC-4DL4B
60” Pipe Length-Galvanized
46DVA-60
4DT-60
N/A
N/A
N/A
N/A
60” Pipe Length-Black
46DVA-60B
4DT-60B
N/A
N/A
N/A
N/A
Adjustable Length 3”-10”-Galvanized
N/A
N/A
N/A
4DAL
N/A
TC-4DLT
Adjustable Length 3”-10”-Black
N/A
N/A
N/A
4DALB
N/A
TC-4DLTB
Adjustable Length 7”-Galvanized
N/A
N/A
4D7A
N/A
N/A
N/A
Adjustable Length 7”-Black
N/A
N/A
4D7AB
N/A
N/A
N/A
Extension Pipe 8-1/2”-Galvanized
46DVA-08A
N/A
N/A
N/A
N/A
N/A
Extension Pipe 8-1/2”-Black
46DVA-08AB
N/A
N/A
N/A
N/A
N/A
Adjustable Length 12”-Galvanized
N/A
N/A
4D12A
N/A
SV4LA12
N/A
Adjustable Length 12”-Black
N/A
N/A
4D12A
N/A
SV4LBA12
N/A
Extension Pipe 16”-Galvanized
46DVA-16A
N/A
N/A
N/A
N/A
N/A
Extension Pipe 16”-Black
46DVA-16AB
N/A
N/A
N/A
N/A
N/A
45º Elbow-Galvanized
46DVA-E45
4DT-EL45
4D45L
N/A
N/A
TE-4DE45
45º Elbow-Black
46DVA-E45B
4DT-EL45B
4DT-EL45B
N/A
N/A
TE-4DE45B
45º Elbow Swivel-Galvanized
See 46DVA-E45
N/A
N/A
4D45L
SV4E45
N/A
45º Elbow Swivel-Black
See 46DVA-E45B
N/A
N/A
4D45LB
SV4EB45
N/A
90º Elbow-Galvanized
46DVA-E90
4DT-EL90S
4DT-EL90S
N/A
N/A
TE-4DE90
90º Elbow-Black
46DVA-E90B
4DT-EL90SB
4DT-EL90SB
N/A
SV4EBR90-1
TE-4DE90B
90º Elbow, Swivel-Galvanized
See 46DVA-E90
N/A
N/A
4D90L
SV4E90-1
N/A
90º Elbow, Swivel-Black
See 46DVA-E90B
N/A
N/A
4D90LB
SV4EB90-1
N/A
90º Starter Elbow, Swivel-Galvanized
N/A
N/A
N/A
4D90A
N/A
N/A
Adaptor*
N/A
N/A
N/A
4D90L
N/A
N/A
Ceiling Support
N/A
4DT-CS
4DFSP
4DSP
SV4SD
TE-4DE45
Cathedral Support Box
46DVA-CS
4DT-CSS
4DRSB
4DRS
SV4CSB
TE-4DE45B
Wall Support/Band
46DVA-WS
4DT-WS/B
4DWS
4DWS
SV4BM
N/A
Offset Support
46DVA-ES (N/A - FPI)
4DT-OS
N/A
N/A
SV4SU
N/A
Wall Thimble-Black
46DVA-WT
4DT-WT
4DWT
4DWT
SV4RSM
TE-4DE90
Wall Thimble Support/Ceiling Support
46DVA-DC
N/A
N/A
N/A
SV4PF
TE-4DE90B
Firestop Spacer
46DVA-FS
4DT-FS
4DFSP
4DFS
SV4BF
N/A
Trim Plate-Black
N/A
4DT-TP
4DFPB
4DCP
SV4LA
N/A
HZ42E Regency Horizon™ Gas Fireplace
19
INSTALLATION
Description
Simpson
Selkirk
Direct Vent Pro®
Direct Temp™
American Metal
Products®
Metal-Fab™
Security
ICC Excel
Sure Seal
Secure- Vent®
Direct
Amerivent Direct
Attic Insulation Shield 12”
46DVA-IS N/A@ FPI
N/A
4DAIS12
N/A
SV4RSA
N/A
Attic Insulation Shield - Cold Climates 36”
N/A
N/A
4DAIS12
N/A
N/A
TM-4AS
Basic Horizontal Termination Kit (A)
Disc.
4DT-HKA
4DHTK2
4DHTKA
SV-SHK
N/A
Horizontal Termination Kit (B)
46DVA-KHA
4DT-HKB
4DHTK1
4DHTKB
SV-HK
N/A
4DT-VKC
4DHTK
4DHTK
SV-FK
N/A
(Changed Components)
Vertical Termination Kit
Disc.
High Wind Vertical Cap
46DVA-VCH
N/A
N/A
N/A
N/A
TM-4VT
High Wind Horizontal Cap
46DVA-HC
N/A
N/A
N/A
N/A
TM-4DHT
Horizontal Square Termination Cap
See 46DVA-HC
4DT-HHC
4DHC
4DHT
SV4CHC-1
TM-4HT
Vertical Termination Cap
46DVA-VC
4DT-HVC
4DVC
4DVT
SV4CGV-1
TM-4VT
Storm Collar
46DVA-08A
4DT-SC
4DSC
4DSC
SV4FC
TM-SC
Adjustable Flashing 0/12-6/12
46DVA-F6
4DT-ST14
4D12S
4DST14
SV4STC14
TF-4FA
Adjustable Flashing 6/12-12/12
46DVA-FLA
4DT-ST36
4D36S
4DST36
SV4STC36
TF-4FB
Vinyl Siding Standoff
46DVA-VSS
4DT-VS
N/A
4DVS
SV4VS
TM-VSS
Vinyl Siding Shield Plate
N/A
4DT-VSP
N/A
N/A
SV4VS
N/A
Snorkel Termination 14”
46DVA-SNKL
N/A
N/A
N/A
N/A
TM-4ST14
Snorkel Termination 36”
N/A
N/A
N/A
N/A
N/A
TM-4ST36
Restrictor Disk
N/A
N/A
N/A
N/A
N/A
TM-4DS
Extended Vertical Termination Cap
N/A
N/A
N/A
N/A
N/A
N/A
Chimney Conversion Kit A (USA only)
46DVA-KCA
N/A
N/A
N/A
N/A
TM-4CA6
Chimney Conversion Kit B (USA only)
46DVA-KCB
N/A
N/A
N/A
N/A
TM-4CA7
Chimney Conversion Kit C (USA only)
46DVA-KCC
N/A
N/A
N/A
N/A
TM-4CA8
Chimney Conversion Kit Masonry
(USA only)
46DVA-KMC
N/A
N/A
N/A
N/A
N/A
Wall Firestop
46DVA-WFS
N/A
N/A
N/A
N/A
TM-4TR
Colinear Flex Connectors
46DVA-ADF
N/A
N/A
N/A
N/A
N/A
FPI
946-506/P
Vent Guard (Optional) for AstroCap
946-205
Vinyl Siding Shield for Riser Vent Terminal
510-994
Rigid Pipe Adaptor (Must use with all rigid piping)
946-208/P
Vent Guard (Optional) for Riser Vent Terminal
640-530/P
Riser Vent Terminal
946-523/P
AstroCap Horizontal Cap
946-605
Starter Collar Increaser 4” x 6-5/8” to 5” x 8”
946-206
Vinyl Siding Standoff for AstroCap
Note: When using Metal-Fab Sure Seal Rigid Piping - please note that the Adaptor (4DDA) must be used in conjunction with FPI Rigid Pipe Adaptor (510-994).
Offset Pipe Selection: Use this table to determine offset pipe lengths.
Pipe Length
(L)
4” x 6-5/8” Venting
Run (X)
Rise (Y)
For specific instructions on venting components - visit the
manufacturers website listed below.
0” (0mm)
4-7/8” (124mm)
13-7/8” (340mm)
6” (152mm)
8” (203mm)
16-1/2” (419mm)
Simpson Direct Vent Pro: www.duravent.com
Selkirk Direct-Temp: www.selkirkcorp.com
9” (229mm)
10-1/8” (257mm)
18-5/8” (473mm)
American Metal Products: www.americanmetalproducts.com
12” (305mm)
12-1/4” (311mm)
20-3/4” (527mm)
Metal-Fab Sure Seal: www.mtlfab.com
24” (610mm)
20-5/8” (524mm)
29-1/8” (740mm)
Security Secure Vent: www.securitychimneys.com
36” (914mm)
29” (737mm)
37-1/2” (953mm)
Industrial Chimney Company: www.icc-rsf.com
48” (1219mm)
37-7/16” (951mm)
45-15/16” (1167mm)
Note: Horizontal runs of vent must be level, or have a 1/4” rise for every 1 foot of run towards the termination.
Never allow the vent to run downward - this could cause high temperatures and may present a possible fire hazard.
Regency Fireplace Products . 6988 Venture St. . Delta, BC . Canada . V4G 1H4 . 604-946-5155 . www.regency-fire.com
20
HZ42E Regency Horizon™ Gas Fireplace
INSTALLATION
VENTING INTRODUCTION
The HZ42E uses the "balanced flue" technology Co-Axial system. The inner liner vents products of combustion to the outside while the outer liner draws
outside combustion air into the combustion chamber thereby eliminating the need to use heated room air for combustion and losing warm room air up the chimney.
Note: These flue pipes must not be connected to any other appliance.
The gas appliance and vent system must be vented directly to the outside of the building, and never be attached to a chimney serving a separate solid fuel
or gas burning appliance. Each direct vent gas appliance must use it's own separate vent system. Common vent systems are prohibited.
VENTING ARRANGEMENT FOR HORIZONTAL TERMINATIONS
The diagram shows all allowable combinations of vertical runs with horizontal terminations, using one 90o (two 45o elbows equal one 90o elbow). (Not including
the starting 45o elbow at the flue collar when using rigid venting.)
Note: Must use optional rigid pipe adapter (Part# 510-994) when using Rigid Pipe Venting Systems.
Horizontal (Feet)
0
2
4
6
8
10
12
14
16
18
20
18
Vertical Height (Feet) from Centreline
16
14
Vent Restrictor
on Set 1
12
10
Vent Restrictor
on Set 0
(Factory Set)
8
6
4
2
33-1/4” (845mm)
Minimum Height
Requirement
0
VENT RESTRICTOR SETTING:
Vent restrictor factory set at Set 0.
Refer to the "Vent Restrictor Position" section for details on how to change the vent restrictor from the factory setting of Set 0 to Set 1 if required.
Note: For horizontal terminations the Regency Direct Vent Flex System may be used for installations with a maximum continuous vent length of
up to 10 feet. If longer runs are required, rigid pipe must be used.
•
•
•
•
•
Maintain clearances to combustibles as listed in "Clearances" section
Horizontal vent must be supported every 3 feet.
Firestops are required at each floor level and whenever passing through a wall.
A vent guard should be used whenever the termination is lower than the specified minimum or as per local codes.
Flex system can only be used up to 10 feet - otherwise rigid venting must be used.
HZ42E Regency Horizon™ Gas Fireplace
21
INSTALLATION
HORIZONTAL TERMINATIONS
FLEX VENT 4" X 6-5/8"
These venting systems, in combination with the HZ42E Direct Vent Gas Fireplace, has been tested and listed as a direct vent heater system by Warnock
Hersey/ Intertek. The location of the termination cap must conform to the requirements in the Vent Terminal Locations diagram in "Exterior Vent Termination
Locations" section.
Regency® Direct Vent (Flex) System Termination Kits includes all the parts needed to install the HZ42E using a flexible vent.
FPI Kit #
Length
Contains:
#946-513
2 Feet
#946-515
4 Feet
#946-516
10 Feet
1)
2)
3)
4)
5)
6)
7)
8)
9)
6-5/8” flexible outer liner (Kit length)
4” flexible inner liner (Kit length)
spring spacers
thimble
AstroCap termination cap
screws
tube of Mill Pac
plated screws
S.S. screws #8 x 1-1/2” drill point
Notes:
1) Liner sections should be continuous without any
joints or seams.
2) Only Flex pipe purchased from Regency® may be
used for Flex installations
3) Horizontal vent must be supported every 3 feet.
4) Regency® Direct Vent System (Flex) is only approved
for horizontal terminations.
5) Flex system can only be used up to a maximum
continuous vent length of up to 10 feet. If longer
runs are required, rigid pipe must be used.
22
HZ42E Regency Horizon™ Gas Fireplace
INSTALLATION
HORIZONTAL TERMINATIONS
RIGID PIPE 4" X 6-5/8"
The minimum components required for a basic horizontal
termination are:
1
1
1
1
1
Horizontal Termination Cap
45o Elbow
Rigid Pipe Adaptor (510-994)
Wall Thimble
Length of pipe to suit wall thickness
(see chart)
Wall thickness is measured from the back standoffs to the inside
mounting surface of termination cap. For siding other than vinyl
furring strips may be used, instead of the vinyl siding standoff, to
create a level surface to mount the vent terminal. The Terminal
must not be recessed into siding. Measure the wall thickness
including furring strips.
If a Vinyl Siding Standoff is required (it must be used with vinyl
siding), measure to outside surface of wall without siding and
add 2 inches.
Vertical Terminal
Storm Collar
Horizontal
Termination Cap
Flashing
Vinyl Siding
Standoff (Optional)
Ceiling Firestop
Flat Wall Installation
Wall Thickness
(inches)
Vent Length Required
(inches)
4" - 5-1/2"
6"
7" - 8-1/2"
9"
10" - 11-1/2"
12"
9" - 14-1/2'
11" - 14-5/8" Adj. Pipe
15" - 23-1/2"
17" - 24" Adj. Pipe
Wall Thimble
Pipe Length
Adj.Pipe Length
o
45 Elbow
Rigid Pipe Adapter
WARNING:
Do not combine venting components from
different venting systems.
However use of the the AstroCapTM and FPI
Riser is acceptable with all systems.
This product has been evaluated by Intertek
for using a Rigid Pipe Adaptor in conjunction
with Duravent Direct-Vent, Selkirk Direct-Temp,
Ameri Vent Direct Venting, ICC Excel Direct
and Security Secure Vent systems. Use of
these systems with the Rigid Pipe adaptor is
deemed acceptable and does not affect the
Intertek WHI listing of components.
When using Rigid Vent other than
Simpson Dura-Vent, 3 screws must be
used to secure rigid pipe to adaptor.
The FPI AstroCapTM and FPI Riser Vent terminal are certified for installations using FPI venting systems as well as Simpson Dura-Vent® Direct Vent,
American Metal Products Ameri Vent Direct Vent, Security Secure Vent®, ICC Excel, Selkirk Direct-Temp. AstroCapTM is a proprietary trademark of FPI
Fireplace Products International Ltd. Dura-Vent® and Direct Vent are registered and/or proprietary trademarks of Simpson Dura-Vent Co. Inc.
HZ42E Regency Horizon™ Gas Fireplace
23
INSTALLATION
HORIZONTAL TERMINATIONS
RIGID PIPE 4" X 6-5/8"
The diagrams below shows examples of horizontal termination arrangements using one, two, or three 90o elbows (two 45o elbows equal one 90o elbow)
1) A maximum of three 90o elbows are permitted (not including the starting 45o elbow at the flue collar when using rigid venting).
2) Minimum distance between elbows is 1 ft. (305mm).
•
•
•
•
•
•
Maintain clearances to combustibles as listed in the "Clearances" section.
Horizontal vent must be supported every 3 feet.
Firestops are required at each floor level and whenever passing through a wall.
Must use optional rigid pipe adaptor (Part# 510-994) when using rigid pipe vent systems.
A vent guard should be used whenever the termination is lower than the specified minimum or as per local codes.
Flex system can only be used up to 10 feet - otherwise rigid venting must be used.
Straight Out Horizontal Venting
Horizontal Venting with One (1) 90o Elbow
Diagram 1
Diagram 2
Option
A)
B)
C)
D)
E)
F)
V
1' (305mm) Minimum
2' (610mm) Minimum
3' (914mm) Minimum
4' (1.22m) Minimum
5' (1.5m) Minimum
6' (1.86m) Minimum
H
3' (914mm) Maximum
6' (1.86m) Maximum
9' (2.7m) Maximum
12' (3.6m) Maximum
15' (4.5m) Maximum
17' (5.1m) Maximum
With the above options, maximum total pipe length if 37 feet with
minimum of 6 feet total vertical and maximum 17 feet total horizontal.
Please note minimum 1 foot between 90o elbows is required.
Please note the minimum centerline for
basic install shown above.
24
HZ42E Regency Horizon™ Gas Fireplace
INSTALLATION
Horizontal Venting with Two (2) 90o Elbows
Horizontal Venting with Three (3) 90o Elbows
One 90o elbow = Two 45o elbows.
One 90o elbow = Two 45o elbows.
Option
V
H + H1
A)
1' Min.
3' Max.
B)
2' Min.
4' Max.
C)
3' Min.
5' Max.
D)
4' Min.
6' Max.
E)
5' Min.
7' Max.
F)
6' Min.
8' Max.
With these options, maximum
total pipe length is 30 feet
with minimum of 6 feet total
vertical and maximum 8 feet
total horizontal.
Option
H
V
H+H1+H2
A)
1' Max.
1' Min.
3' Max.
B)
2' Max.
3' Min.
5' Max.
C)
3' Max.
5' Min.
6' Max.
Please note minimum 1
foot between 90o elbows is
required.
D)
4' Max.
7' Min.
7' Max.
E)
5' Max.
9' Min.
8' Max.
F)
6' Max.
11' Min.
9' Max.
Restrictor Position - Set 0 (factory setting)
With these options,
maximum total pipe
length is 30 feet with
minimum of 11 feet
total vertical and
maximum 9 feet total
horizontal.
Please
note
minimum 1 foot
between 90o elbows
is required.
Restrictor Position - Set 0 (factory setting)
Horizontal Venting with Two (2) 90o Elbows
One 90o elbow = Two 45o elbows.
Option
H
V
H+H1
A)
1' Max.
1' Min.
3' Max.
B)
2' Max.
2' Min.
5' Max.
C)
3' Max.
4' Min.
6' Max.
D)
4' Max.
6' Min.
7' Max.
E)
5' Max.
8' Min.
8' Max.
With these options,
maximum total pipe
length is 30 feet with
minimum of 8 feet total
vertical and maximum
8 feet total horizontal.
Please note minimum
1 foot between 90o
elbows is required.
Restrictor Position - Set 0 (factory setting)
HZ42E Regency Horizon™ Gas Fireplace
25
INSTALLATION
Horizontal Venting with Three (3) 90o Elbows
One 90o elbow = Two 45o elbows.
Option
V
H
V+V1
H+H1
A)
2' Min.
1' Max.
3' Min.
4' Max.
B)
3' Min.
2' Max.
4' Min.
5' Max.
C)
4' Min.
3' Max.
6' Min.
6' Max.
D)
5' Min.
4' Max.
8' Min.
7' Max.
E)
6' Min.
5' Max.
10' Min.
8' Max.
F)
7' Min.
6' Max.
12' Min.
9' Max.
With these options,
maximum total pipe
length is 30 feet with
minimum of 12 feet
total vertical and
maximum 9 feet total
horizontal.
Please
note
minimum 1 foot
between 90o elbows
is required.
Restrictor Position - Set 0 (factory setting)
26
HZ42E Regency Horizon™ Gas Fireplace
INSTALLATION
VENTING ARRANGEMENT FOR VERTICAL TERMINATIONS
Horizontal (Feet)
0
The shaded area in the diagram shows all allowable combinations
of straight vertical and offset to vertical terminations, using two
90o elbows, with Rigid Pipe Venting Systems.
2
4
6
8
10
12
14
18
16
40
Two 45o elbows equal to one 90o elbow. Maximum of four
45o elbows allowed, not including the starting 45o elbow at the
flue collar.
•
Vent must be supported at offsets.
•
Minimum distance between elbows is 1 ft. (305mm).
•
Maintain clearances to combustibles as listed in the
"Clearances" section.
•
Horizontal vent must be supported every 3 feet.
•
Firestops are required at each floor level and whenever
passing through a wall.
30
•
Must use optional rigid pipe adaptor (Part# 510-994)
when using rigid pipe vent systems.
28
•
Refer to the "Vent Restrictor Position" section for
details on how to change the vent restrictor from the
factory setting of Set 0 to Set 1 or Set 2 if required.
26
Maximum: 40 ft. (12.2m)
38
36
34
32
Vent Restrictor on Set 2
24
Vent Restrictor on Set 1
20
Maximum: 27 ft. (8.2m)
Vertical Height (Feet)
22
18
16
14
Please note min. 1 foot between 90o
elbows is required.
12
Vent Restrictor on Set 0
(factory set)
10
Minimum
8’6” (2.6m)
8
6
2
0
Minimum length of pipe
between elbows 12” (305mm)
HZ42E Regency Horizon™ Gas Fireplace
Min. 33-1/4”
(1118mm)
4
Max. 10’ (3m)(centerline to centerline)
27
20
INSTALLATION
VERTICAL TERMINATIONS
RIGID PIPE 4" X 6-5/8"
The minimum components required for a basic vertical
termination are:
1
1
1
1
1
1
1
Vertical Termination Cap
45o Elbow
Rigid Pipe Adaptor (510-994)
Ceiling Firestop
Flashing
Storm Collar
Length of pipe to suit wall thickness
(see chart)
Vertical Terminal
Storm Collar
Flashing
Galvanized pipe is desirable above the roofline due to its higher
corrosion resistance. Continue to add pipe sections through the
flashing until the height of the vent cap meets the minimum height
requirements specified in Dia. 4 or local codes. Note that for steep
roof pitches, the vertical height must be increased. A poor draft, or
down drafting can result from high wind conditions near big trees
or adjoining roof lines, in these cases, increasing the vent height
may solve the problem.
Vinyl S
Standoff (O
Ceiling Firestop
Pipe Length
Adj.Pipe L
o
45 Elbow
Roof Pitch
flat to 7/12
over 7/12 to 8/12
over 8/12 to 9/12
over 9/12 to 10/12
over 10/12 to 11/12
over 11/12 to 12/12
over 12/12 to 14/12
over 14/12 to 16/12
over 16/12 to 18/12
over 18/12 to 20/12
over 20/12 to 21/12
Minimum Vent Height
Feet
Meters
2
0.61
2
0.61
2
0.61
2.5
0.76
3.25
0.99
4
1.22
5
1.52
6
1.83
7
2.13
7.5
2.29
8
2.44
Rigid Pipe Adapter
WARNING:
Do not combine venting components from different venting systems.
However use of the the AstroCapTM and FPI Riser is acceptable with all systems.
This product has been evaluated by Intertek for using a Rigid Pipe Adaptor in conjunction
with Duravent Direct-Vent, Selkirk Direct-Temp, Ameri Vent Direct Venting, ICC Excel Direct
and Security Secure Vent systems. Use of these systems with the Rigid Pipe adaptor is
deemed acceptable and does not affect the Intertek WHI listing of components.
When using Rigid Vent other than
Simpson Dura-Vent, 3 screws must be
used to secure rigid pipe to adaptor.
The FPI AstroCapTM and FPI Riser Vent terminal are certified for installations using FPI venting systems as well as Simpson Dura-Vent® Direct Vent,
American Metal Products Ameri Vent Direct Vent, Security Secure Vent®, ICC Excel, Selkirk Direct-Temp. AstroCapTM is a proprietary trademark of FPI
Fireplace Products International Ltd. Dura-Vent® and Direct Vent are registered and/or proprietary trademarks of Simpson Dura-Vent Co. Inc.
28
HZ42E Regency Horizon™ Gas Fireplace
INSTALLATION
VERTICAL TERMINATIONS
RIGID PIPE 4" X 6-5/8"
•
•
•
•
•
•
•
Two 45o elbows equal to one 90o elbow. Maximum of four 45o elbows allowed, not including the starting 45o elbow at the flue collar.
Vent must be supported at offsets.
Minimum distance between elbows is 1 ft. (305mm).
Maintain clearances to combustibles as listed in the "Clearances" section.
Horizontal vent must be supported every 3 feet.
Firestops are required at each floor level and whenever passing through a wall.
Must use optional rigid pipe adaptor (Part# 510-994) when using rigid pipe vent systems.
Vertical Venting with One (1) 90o Elbow
One 90o elbow = Two 45o elbows.
Option
A)
B)
C)
D)
V
1' (305mm) Minimum
2' (610mm) Minimum
3' (914mm) Minimum
4' (1.22m) Minimum
H
2' (610mm) Maximum
4' (1.22m) Maximum
6' (1.86m) Maximum
8' (2.4m) Maximum
With the above options, maximum total pipe length if 37 feet with
minimum of 4 feet total vertical and maximum 8 feet total horizontal.
Please note minimum 1 foot between 90o elbows is required.
Vertical Venting with Two (2) 90o Elbows
Vertical Venting with Two (2) 90o Elbows
o
o
One 90 elbow = Two 45 elbows.
Option
V
H
V+V1
A)
1' Min. 4' Max.
2' Min.
B)
2' Min. 5' Max.
3' Min.
C)
3' Min. 6' Max.
4' Min.
D)
4' Min. 7' Max.
5' Min.
E)
5' Min. 8' Max.
6' Min.
One 90o elbow = Two 45o elbows.
With these options,
maximum total pipe
length is 30 feet with
minimum of 6 feet total
vertical and maximum 8
feet total horizontal.
Option
H + H1
V
A)
2' Max.
2' Min.
B)
3' Max.
3' Min.
C)
4' Max.
4' Min.
Please note minimum
1 foot between 90 o
elbows is required.
D)
5' Max.
5' Min.
E)
6' Max.
6' Min.
Restrictor Position - Set 0 (factory setting)
With these options, maximum
total pipe length is 30 feet
with minimum of 6 feet total
vertical and maximum 6 feet
total horizontal.
Please note minimum 1
foot between 90o elbows is
required.
Restrictor Position - Set 0 (factory setting)
For additional vertical venting with
2 x 90o elbows, refer to "Rigid Pipe
Venting Arrangements" Section.
HZ42E Regency Horizon™ Gas Fireplace
29
INSTALLATION
Vertical Venting with Three (3) 90o Elbows
One 90o elbow = Two 45o elbows.
Option
A)
B)
C)
D)
E)
H
1' Max.
2' Max.
3' Max.
4' Max.
5' Max.
V
1' Min.
2' Min.
3' Min.'
4' Min.
5' Min.
H + H1
3' Max.
4' Max.
5' Max.
6' Max.
7' Max.
V + V1
3' Min.
5' Min.
7' Min.
9' Min.
11' Min.
With these options, max. total
pipe length is 30 feet with min.
of 11 feet total vertical and
max. 7 feet total horizontal.
Please note min. 1 foot
between 90 o elbows is
required.
Restrictor Position - Set 0 (factory setting)
Vertical Venting with Three (3) 90o Elbows
One 90o elbow = Two 45o elbows.
Option
A)
B)
C)
D)
E)
F)
V
2' Min.
3' Min.
4' Min.
5' Min.
6' Min.
7' Min.
H + H1
3' Max.
4' Max.
5' Max.
6' Max.
7' Max.
8' Max.
V + V1 With these options, max. total
4' Min. pipe length is 30 feet with min.
6' Min. of 10 feet total vertical and
7' Min. max. 8 feet total horizontal.
Please note min. 1 foot
8' Min. between 90 o elbows is
9' Min. required.
10' Min.
Restrictor Position - Set 0 (factory setting)
30
HZ42E Regency Horizon™ Gas Fireplace
INSTALLATION
UNIT INSTALLATION
WITH HORIZONTAL
TERMINATION
5) Assemble the desired combination of pipe and
elbows to the appliance adaptor and twist-lock
for a solid connection.
4" X 6-5/8"
VENTING
(Rigid Vent Systems)
Note: For best results and optimum performance
with each approved venting system, it is
highly recommended to apply “Mill-Pac”
sealant (supplied) to every inner pipe
connection. Failure to do so may result
in drafting or performance issues not
covered under warranty. Silicone (red
RTV) is optional.
* Clearances noted below must be maintained;
except when passing through a wall, ceiling or at the
termination where the use of a firestop or wall thimble
reduces clearance to 1-1/2" (38mm).
Horizontal Top*
3" (76mm)*
Horizontal Side
2 " (51mm)
Horizontal Bottom
2" (51mm)
Vertical Vent
2" (51mm)
Below are the recommended framing
dimensions (inside measurements) for the
4" x 6-5/8" rigid vent terminations - for use
with a firestop or wall thimble.
Recommended Framed Opening
Size
Vent Size
Framing Size
4" x 6 - 5/8"
10" x 10"
Install the vent system according to the
manufacturer's instructions included with the
components.
1) Set the unit in its desired location. Check to
determine if wall studs or roof rafters are in
the way when the venting system is attached.
If this is the case, you may want to adjust the
location of the unit. Rough in the gas preferably
on the right side of the unit and the electrical
(junction block is on the left side) on the left.
2) Direct Vent pipe and fittings are designed with
special twist-lock connections to connect the
venting system to the appliance flue outlet. A
twist-lock appliance adaptor is required.
3) In conjunction with the Approved Vent system,
install the adaptor after the unit is set in its
desired location. Put a bead of high temperature
silicone inside the outer section of the adapter
and a bead of Mill Pack on the inner collar. Slip
the adapter over the existing inner and outer
flue collar. Fasten to the outer collar only with
the 3 supplied screws (drilling pilot holes will
make this easier).
4) Level the fireplace and fasten it to the framing
using nails or screws through the top and side
nailing strips.
Note: If installing termination on a vinyl siding
covered wall, a vinyl siding standoff or
furring strips must be used to ensure
that the termination is not recessed into
the siding.
Horizontal runs of vent must be supported every
3 feet (0.9meter). Wall straps are available for
this purpose.
6) Mark the wall for a square hole.-see chart to left
for size. The center of the square hole should line
up with the center-line of the horizontal pipe. Cut
and frame the square hole in the exterior wall
where the vent will be terminated. See diagram
2 for center line requirements.
If the wall being penetrated is constructed of
non-combustible material, i.e. masonry block
or concrete, an 8" (203mm) diameter hole is
acceptable.
Note:
a) The horizontal run of vent must be level, or
have a 1/4 inch rise for every 1 foot of run
towards the termination. Never allow the
vent to run downward. This could cause
high temperatures and may present the
possibility of a fire.
b) The location of the horizontal vent termination
on an exterior wall must meet all local and
national building codes, and must not be
blocked or obstructed. See "Exterior Vent
Termination Locations" section for more
details.
Diagram 5
The four wood screws provided should be
replaced with appropriate fasteners for stucco,
brick, concrete, or other types of sidings.
8) Before connecting the horizontal run of vent pipe
to the vent termination, slide the Wall Thimble
over the vent pipe. The wall thimble is required
for all horizontal terminations.
9) Slide the appliance and vent assembly towards
the wall carefully inserting the vent pipe into the
vent cap assembly. It is important that the vent
pipe extends into the vent cap sufficient distance
so as to result in a minimum pipe overlap of
1-1/4 inches (32mm). Secure the connection
between the vent pipe and the vent cap.
10) Install wall thimble in the center of the framed
hole and attach with wood screws (Diagram 7).
center
of hole
CL
CL
33-1/4" (845mm)
Min. height
(Z-flex & Rigid)
Minimum Vent Clearances
to Combustibles
7) Ensure that the pipe clearances to combustible
materials are maintained (Diagram 5). Install
the termination cap.
Diagram 7
Diagram 2
Diagram 1
HZ42E Regency Horizon™ Gas Fireplace
31
INSTALLATION
4" X 6-5/8"
VENTING
(Flex Vent Systems)
Minimum Vent Clearances
to Combustibles
* Clearances noted below must be maintained;
except when passing through a wall, ceiling or at the
termination where the use of a firestop or wall thimble
reduces clearance to 1-1/2" (38mm).
Horizontal Top*
3" (76mm)*
Horizontal Side
2 " (51mm)
Horizontal Bottom
2" (51mm)
Vertical Vent
2" (51mm)
Below are the recommended framing
dimensions (inside measurements) for the
4" x 6-5/8" and 5" x 8" rigid vent terminations for use with a firestop or wall thimble.
Recommended Framed Opening
Size
Vent Size
Framing Size
4" x 6 - 5/8"
10" x 10"
1) Locate the unit in the framing, rough in the gas
(preferably on the right side of the unit). Locate
the centerline of the termination and mark wall
accordingly. Cut an square hole in the wall - see
chart (inside dimension).
Note: If installing termination on a siding covered wall, a vinyl siding standoff or vinyl
furring strips must be used to ensure that
the termination is not recessed into the
siding.
NOTE:
Horizontal sections must be supported
at intervals not exceeding 3 feet (0.9
meter). (Flame picture and performance
will be affected by sags in the liner).
ASTROCAP
DIMENSIONS (946-523/P)
4) Separate the 2 halves of the wall thimble and
securely fasten the one with the tabs to the
outside wall making sure that the tabs are on
top and bottom. Fasten the other thimble half
to the inside wall. The thimble halves slip inside
each other and can be adjusted for 2 x 4 or 2 x
6 walls.
5) Slip the assembled liner and termination
assembly through the thimble making sure the
termination cap faces up (there are markings
on the cap that show which wayis up). This will
position the termination cap with proper down
slope for draining water. Fasten the cap to the
outer wall with the 4 supplied screws.
11”
(294mm)
11”
(294mm)
6) Pull the centre inner and outer flex liner out
enough to slip over the flue collars of the
fireplace. (You may wish to cut the liner shorter
to make it more workable.) Do not bend liner
more than 90o. The liners must slip over the
collars a minimum of 1-3/8".
7) Apply Mill Pac over the fireplace inner flue
collar and slip the inner flex liner down over it
and attach with 3 supplied screws.
8) Do the same with the outer flue collar and outer
flex liner.
33-1/4"
UNIT INSTALLATION
WITH HORIZONTAL
TERMINATION
9) Apply a bead of silicone between the thimble
and termination and around the outer edge of
the terminal at the wall in order to keep the
water out.
IMPORTANT: Do not locate termination hood
where excessive snow or ice buildup may
occur. Be sure to check vent termination
area after snow falls, and clear to prevent
accidental blockage of venting system. When
using snow blowers, make sure snow is not
directed towards vent termination area.
2) Level the fireplace and fasten it to the framing
using nails or screws through the nailing strips.
3) Assemble the vent assembly by applying Mill
Pac to the inner flue collar of the termination
and slipping the inner flex liner over it at least
1-3/8" (35mm). Fasten with the 3 screws (drilling pilot holes will make this easier). Apply Mill
Pac or high temperature silicone to the outer
flex pipe and slip it over the outer flue collar of
the vent terminal at least 1-3/8"(35mm) and
fasten with the 3 screws.
32
HZ42E Regency Horizon™ Gas Fireplace
INSTALLATION
UNIT INSTALLATION
WITH VERTICAL
TERMINATION
4) Assemble the desired lengths of pipe and
elbows. Ensure that all pipes and elbow connections are in the fully twist-locked position
and sealed.
4" X 6-5/8" VENTING
(Rigid Vent Systems)
Diagram 4
1) Maintain the 1-1/2" clearances (air spaces)
to combustibles when passing through
ceilings, walls, roofs, enclosures, attic rafter,
or other nearby combustible surfaces. Do not
pack air spaces with insulation.
Check "Venting" Sections for
the maximum vertical rise of the
venting system and the maximum
horizontal offset limitations.
2) Set the gas appliance in its
desired location. Drop a plumb
bob down from the ceiling to the
position of the appliance flue
exit, and mark the location where
the vent will penetrate the
ceiling. Drill a small hole
at this point. Next, drop a
plumb bob from the roof to
the hole previously drilled
in the ceiling, and mark the
Diagram 1
spot where the vent will penetrate the roof.
Roof Pitch
NOTE: For best results and optimum performance with each approved venting system, it
is highly recommended to apply “Mill-Pac”
sealant (supplied) to every inner pipe connection. Failure to do so may result in drafting or
performance issues not covered under warranty.
Silicone (red RTV) is optional.
5) Cut a hole in the roof centered on the small
drilled hole placed in the roof in Step 2. The hole
should be of sufficient size to meet the minimum
requirements for clearance to combustibles
of 1-1/2". Slip the flashing under the shingles
(shingles should overlap half the flashing) as
per Diagram 3.
3) A Firestop spacer must be installed in the
floor or ceiling of every level. To install the
Firestop spacer in a flat ceiling or wall, cut
a 10 inch square hole. Frame the hole as
shown in Diagram 2 and install the firestop.
Note: All vertical terminations are
vented using 4" x 6-5/8" venting and
rigid pipe adaptor #510-994.
flat to 7/12
over 7/12 to 8/12
over 8/12 to 9/12
over 9/12 to 10/12
over 10/12 to 11/12
over 11/12 to 12/12
over 12/12 to 14/12
over 14/12 to 16/12
over 16/12 to 18/12
over 18/12 to 20/12
over 20/12 to 21/12
Minimum Vent Height
Feet
Meters
2
0.61
2
0.61
2
0.61
2.5
0.76
3.25
0.99
4
1.22
5
1.52
6
1.83
7
2.13
7.5
2.29
8
2.44
7) Ensure vent is vertical and secure the base of
the flashing to the roof with roofing rails, slide
storm collar over the pipe section and seal with
a mastic.
8) Install the vertical termination cap by twistlocking it.
Note: Any closets or storage spaces, which the
vent passes through must be enclosed.
Diagram 3: The upper half of the flashing is installed
under the roofing material and not nailed down
until the chimney is installed. This allows for small
adjustments.
6) Continue to assemble pipe lengths.
Note: If an offset is necessary in the attic to
avoid obstructions, it is important to
support the vent pipe every 3 feet, to
avoid excessive stress on the elbows,
and possible separation. Wall straps
are available for this purpose.
Diagram 2
HZ42E Regency Horizon™ Gas Fireplace
Galvanized pipe is desirable above the roofline
due to its higher corrosion resistance. Continue
to add pipe sections through the flashing until the
height of the vent cap meets the minimum height
requirements specified in Dia. 4 or local codes.
Note that for steep roof pitches, the vertical
height must be increased. A poor draft, or down
drafting can result from high wind conditions
near big trees or adjoining roof lines, in these
cases, increasing the vent height may solve the
problem.
33
INSTALLATION
HZ42E-NG SYSTEM DATA
Min. Supply Pressure
5" WC (1.25 kpa)
Low Setting Man.
Pressure
1.6" WC (0.40kpa)
Max. Manifold
Pressure
3.5" WC (0.87 kpa)
Orifice Size
#40 DMS
Minimum Input
17,500 Btu/h
(5.13 kW)
Maximum Input
26,000 Btu/h
(7.62 kW)
PILOT ADJUSTMENT
Burner
Flame Sensor
HZ42E-LP SYSTEM DATA
Min. Supply Pressure
12" WC (2.98 kpa)
Low Setting Man.
Pressure
6.4" WC (1.59kpa)
Max. Manifold
Pressure
10" WC (2.49 kpa)
Orifice Size
#53 DMS
Minimum Input
19,500 Btu/h
(5.71 kW)
Maximum Input
24,500 Btu/h
(7.18 kW)
HIGH ELEVATION
This unit is approved for altitude 0 to 4500 ft.
(CAN1 2.17-M91).
GAS LINE
INSTALLATION
Since some municipalities have additional local
codes it is always best to consult with your local
authorities and the CAN/CGA B149 installation
code.
For USA installations follow local codes and/or the
current National Fuel Gas Code, ANSI Z223.1.
When using copper or flex connectors use only
approved fittings. Always provide a union so that
gas lines can be easily disconnected for servicing.
Flare nuts for copper lines and flex connectors
are usually considered to meet this requirement.
NOTE: A shutoff / dante valve should be supplied in or near the unit (or as per local codes)
for ease of servicing this appliance.
IMPORTANT: Always check for gas leaks with
a soap and water solution or gas leak detector.
Do not use open flame for leak testing.
Pilot
Ignitor
flame pattern has three strong blue flames: 1
flowing around the thermopile, 1 around the
thermocouple and 1 flowing across the burner.
1)
2)
3)
4)
5)
6)
7)
Note: If you have an incorrect flame pattern,
contact your Regency® dealer for further
instructions.
Manual high/low adjustment
Pilot adjustment
Outlet Pressure Tap
Inlet Pressure Tap
Pilot Outlet
Main Gas Outlet
Main Gas Inlet
3
4
Incorrect flame pattern will have small, probably
yellow flames, not coming into proper contact with
the burner or thermopile or thermocouple.
GAS PIPE PRESSURE
TESTING
2
1
The appliance must be isolated from the gas supply
piping system by closing its individual manual shut-off
valve during any pressure testing of the gas supply
piping system at test pressures equal to or less
than 1/2 psig. (3.45 kPa). Disconnect piping from
valve at pressures over 1/2 psig.
The manifold pressure is controlled by a regulator
built into the gas control, and should be checked at
the pressure test point.
7
Note: To properly check gas pressure, both
inlet and manifold pressures should be
checked using the valve pressure ports
on the valve.
5
6
1) Make sure the valve is in the "OFF" position.
2) Loosen the "IN" and/or "OUT" pressure tap(s),
turning counterclockwise with a
1/8" wide flat screwdriver.
3) Attach manometer to "IN" and/or "OUT" pressure
tap(s) using a 5/16" ID hose.
4) Light the pilot and turn the valve to "ON" position.
5) The pressure check should be carried out with
the unit burning and the setting should be within
the limits specified on the safety label.
6) When finished reading manometer, turn off the
gas valve, disconnect the hose and tighten the
screw (clockwise) with a 1/8" flat screwdriver.
Note: Screw should be snug, but do not over
tighten.
34
886 S.I.T. VALVE
DESCRIPTION
Periodically check the pilot flames. Correct
AERATION ADJUSTMENT
The burner aeration is factory set but may need
adjusting due to either the local gas supply or
altitude. Open the air shutter for a blue flame or
close for a more yellow flame.
Minimum Air Shutter Opening:
NG
LP
Fully Closed
3/8"
Note: Any damage due to carboning resulting
from improperly setting the aeration
controls is NOT covered under warranty.
HZ42E Regency Horizon™ Gas Fireplace
INSTALLATION
WIRING DIAGRAM
This heater does not require a 120V A.C. supply for operation. In case of a power failure, the burner switch and the optional remote control/thermostat will
continue to operate. However, a 120V A.C. power supply is needed for the AC Adaptor.
(Do not cut the ground terminal off under any circumstances.)
NOTE: Even if the fan is not purchased with the unit, it is still a good idea to bring power to the receptacle box (provided with the unit) in case the
fan is installed at a later date.
Note: 4 AA batteries must be installed to operate
the burner switch.
Do not use a 9 volt battery.
IMPORTANT: If the optional remote control is used, the AA batteries normally installed into the battery holder must be removed. The AA batteries in the
receiver now operate the unit. Having AA batteries in both the battery holder and receiver will damage the gas valve.
Ground
Black
Power
Switch
Electrical Connection Alternative Scheme "B",
Power at Switch
Fan
Speed
Control
Wall Junction Box
L1
~
*Speed Control
Switch with lead wires
Ground
To Fan (see above)
Red
Break Tab
Copper terminals
Do Not Break Tab
on Neutral (silver terminals)
Black
AC Adaptor (see AC Adaptor in
Wire Nuts
Black (Hot)
120 Volts White (Neutral)
60 Hz Copper Ground
Wire
Black
White
Ground
14 AWG wire
N
*Wire Clamp
Receptacle
in Unit
* = supplied with fan kit
*Receptacle Box
inside stove
Other parts are to be supplied
by electrician or installer
*Receptacle
(dedicated use
by unit fan only)
HZ42E Regency Horizon™ Gas Fireplace
35
INSTALLATION
OPTIONAL ACCENT LIGHTING WIRING DIAGRAM
Wall Mounted
Switch
L1
L2
Hot
Neutral
Optional Accent Lights
Receptacle
in Unit
36
HZ42E Regency Horizon™ Gas Fireplace
INSTALLATION
AC POWER ADAPTOR INSTALLATION (FOR SUREFIRE SYSTEM)
An optional AC power adaptor may be installed as a constant power source for the SureFire system.
NOTE: AC power adaptor is not required when using GTMF Remote
IMPORTANT: Recommend removing the 4-AA batteries in the SureFire receiver.
This will avoid battery leakage and power drainage. 4-AA Battery pack may be re-installed into receiver during power outages.
NOTE: For all Gas Fireplaces 120 volt power must be brought to the receptacle box inside the ERWWRPRIWKH¿UHER[(provided with the unit).
All Freestanding Gas Stoves & Gas Inserts will need a receptacle box located outside / near the unit
so that the AC Power Adaptor can be plugged in.
INSTALL AC ADAPTOR WITH SUREFIRE WALL SWITCH ONLY - (WITHOUT REMOTE)
1) Locate “DC Supply” tag on wire harness. For location in unit
see remote installation page in owners manual.
2) Connect the male end from AC adaptor to the female end
tagged “DC Supply” on wiring harness in unit.
3) Plug AC adaptor into 120V wall outlet (or into 120V receptacle if
LQVWDOOHGLQVLGHWKHJDV¿UHSODFH¿UHER[
4) Neatly tuck any loose AC Power Adaptor wires neatly underneath /
inside the appliance.
Note: (QVXUHWKDWZLUHVGRQRWWRXFKWKHXQGHUVLGHRIWKH¿UHER[
(keep wires away from the heat as much as possible).
INSTALL AC ADAPTOR WITH SUREFIRE PROFLAME GT / GTM REMOTE
This method also applies for models, HZ30E - HZ40E - L390E - HZI390E
1) Connect the male end of the AC adaptor to the female end of the
wire adaptor (supplied with AC adaptor) together as shown .
Wire adaptor
AC adaptor
2) Locate FCM - COM connector on the Remote wire harness see manual for location in unit.
3) Plug in wire adaptor to FCM - COM connector - be careful not
WRGDPDJHHQGV7KLVRQO\¿WVRQHZD\'R1RW)RUFHLQZURQJZD\
AC adaptor
wire adaptor
FCM - COM
4) Plug AC adaptor into 120V wall outlet (or into 120V receptacle if
LQVWDOOHGLQVLGHWKHJDV¿UHSODFH¿UHER[
5) Neatly tuck any loose AC Power Adaptor wires neatly underneath /
inside the appliance.
Note: (QVXUHWKDWZLUHVGRQRWWRXFKWKHXQGHUVLGHRIWKH¿UHER[
(keep wires away from the heat as much as possible).
FCM - COM
HZ42E Regency Horizon™ Gas Fireplace
37
INSTALLATION
Optional
WALL THERMOSTAT
A wall thermostat may be installed if desired,
connect the wires as per the wiring diagram. Use
table below to determine the maximum wire length.
Note: Preferable if the thermostat is installed
on an interior wall.
®
Regency offers an optional programmable
thermostat but any 250-750 millivolt rated nonanticipator type thermostat that is CSA, ULC or
UL approved may be used.
CAUTION
Do not wire millivolt
wall thermostat wires
to 120V wire.
Optional
REMOTE CONTROL
WALL SWITCH
(Included with Unit)
Use the Regency® Remote Control approved for this
unit. Use of other systems may void your warranty.
The remote control comes with a hand held transmitter, a receiver and a wall mounting plate.
1) Choose a convenient location on the wall to
install the receiver and the receptacle box
(protection from extreme heat is very important).
Run wires from the fireplace to that location.
Use Thermostat Wire Table.
1) Run the supplied 10' of wire through the right
or left side gas inlet opening. Be careful not to
damage wire.
Note: We recommend a maximum of 10' of
wire but if you wish to go with a longer
run, use the Thermostat Wire Table.
2) Connect the wire to the wall switch and install
into the receptacle box. Also attach wires to
the valve as shown below.
CAUTION
Do not wire millivolt
wall switch wires
to 120V wire.
CAUTION
Do not wire millivolt
remote control wires
to 120V wire.
Thermostat Wire Table
Recommended Maximum Lead Length
(Two-Wire) When Using Wall
Thermostat (CP-2 System)
Wire Size
Max. Length
14 GA.
50 Ft.
16 GA.
32 Ft.
18 GA.
20 Ft.
20 GA.
12 Ft.
22 GA.
9 Ft.
GT /GTM REMOTE FEATURES
** GTMF NOT OFFERED ON THE HZ42E
584 Proflame GT Series
Feature Sheet
**
1
1
1
(X) Indicates Included Feature
Note 1 ~ Proflame Flame Modulator for GTM & GTMF Remote Controls are sold seperately. Choice of NG or
LP flame modulator (to match unit fuel type). See Regency Retail Price pages for complete details
Note: Regency Proflame systems include a white and black wall cover & switch.
38
HZ42E Regency Horizon™ Gas Fireplace
INSTALLATION
GT REMOTE INSTALLATION
DFBC = digital fireplace burner control
5) Locate the DFC wire from the receiver wire harness and connect to the
DC supply wire from the DFBC.
1)
Remove the faceplate and glass door to access to DFBC &
battery pack tray.
2)
Lift DFBC and battery pack up and out.
HZ42E
HZ42STE
3) Disconnect connector from battery holder and remove from tray – (battery
holder is attached by Velcro to tray).
HZ42E
Note: DO NOT USE 4 AA batteries in the battery pack on the tray - the
DFBC is now powered by the receiver batteries in the wall.
HZ42STE
4) Remove the 4 AA batteries if installed, reconnect the connector to the
battery pack and put back onto Velcro strip
HZ42E Regency Horizon™ Gas Fireplace
39
INSTALLATION
GTM REMOTE INSTALLATION
DFBC = digital fireplace burner control
6) Locate the DFC wire from the receiver wire harness and connect to the
DC supply wire from the DFBC.
1)
Remove the faceplate and glass door to access to DFBC &
battery pack tray.
2)
Lift DFBC and battery pack up and out.
HZ42E
HZ42STE
Disconnect connector from battery holder and remove from tray – (battery
holder is attached by Velcro to tray).
Note: DO NOT USE 4 AA batteries in the battery pack on the tray - the
DFBC is now powered by the receiver batteries in the wall.
7) Remove the hi/lo knob from the valve head, if installed, by removing
2 screws as shown below. Ensure diaphragm is removed.
HZ42E
HZ42STE
Remove the 4 AA batteries if installed, reconnect the connector to the
battery pack and put back onto Velcro strip
Locate the Green and White wires from the DFBC module wire harness;
connect the spade connectors from the receiver wire harness, (TH)
Green to (DFBC) Green and (TH/TP) White to (DFBC) White
40
8) Install the stepper motor in the same location the hi/lo knob was
removed from - with 2 screws as shown below.
HZ42E Regency Horizon™ Gas Fireplace
INSTALLATION
9) Install the ground wire to the ground lug just behind and to the left of the
valve on the HZ42E and to the right of the valve on the HZ42STE.
HZ42E
HZ42STE
14) Install the receiver in the wall or if that is not possible - to the tray.
HZ42E
HZ42STE
10) Install 4 - AA batteries into the receiver, ensure correct polarity.
15) HZ42E Only: Manoeuvre the tray into the base of the unit using the
stops to guide how far back the tray sits.
HZ42STE Only: Manoeuvre the tray into the two L brackets on the backs
of the front wall of the unit base.
11) Plug receiver wires into the back of the receiver and bundle wires
with the wire clip as shown below.
HZ42E
12) Connect GTM motor wire from the stepper motor to the wire connector
from the receiver wire harness.
HZ42STE
HZ42E Only:
16) Install the heat shield over the tray by slotting tabs into slots located
location shown below.
13) Program Receiver and transmitter (refer to manual)
Note: DO NOT USE 4 AA batteries in the battery pack on the tray; the
DFBC is now powered by the receiver batteries in the wall.
HZ42E Regency Horizon™ Gas Fireplace
41
INSTALLATION
OPTIONAL REFLECTIVE PANEL INSTALLATION
Before installation, panels must be handled and cleaned as per instructions noted below:
Stainless Steel Panels
Black Enamel Panels
• Stainless panels must be inspected for scratches and dimples prior
to installation. All claims to be recorded at this time.
Claims for damage after installation will not receive consideration.
• Black Enamel panels must be inspected for scratches and dimples
prior to installation. All claims to be recorded at this time.
Claims for damage after installation will not receive consideration.
• Use a hair dryer to remove the protective coating from the panels.
• To protect the finish during installation and handling - cotton gloves
MUST be worn at all times while handling the panels.
• Stainless panels will discolor a little during normal operation.
• Black Enamel panels will discolor a little during normal operation. This
*
All hand and finger marks MUST be cleaned off with a soft cloth. Use
an ammonia based cleaner (ie. glass cleaner) to remove any fingerprints
before applying heat to the unit.
Failure to do this will result in burn stain on panels which you
will be unable to remove. Not protected by product warranty.
This is normal and should not be considered a defect.
All hand and finger marks MUST be cleaned off with a soft cloth and
a stainless steel cleaner. Most stainless steel cleaners leave a film/
residue on the surface of the panels. Use an ammonia based cleaner
(ie. glass cleaner) to remove this film before applying heat to the unit.
Failure to do this will result in burn stains on panels which you
will be unable to remove. Not protected by product warranty.
is normal and should not be considered a defect.
*
1) Position the left side panel in place - top of panel in first, then fit the
bottom tab into the slot at the bottom of the firebox as shown below.
Repeat for right side panel.
90 degree
bend faces
towards center
of unit on both
left and right
side panels
Left Side
Panel
Shown
Right side panel in position
2) Fit the back panel into position by clearing the pilot shield - bottom
of panel goes in first.
Then fit the tabs on the bottom left and right side of the back panel
into the slots at the base of the firebox.
Secure the back panel in place by placing the brackets over the
screws on the top of the inside left and right side of the firebox and
tighten the screw to hold the bracket against the back panel shown
below.
Left Side
Bracket
Fit side panel tab into slot
Right side back panel tab fitted into slot
Left side panel in position
42
Bracket shown in place on right side of the firebox
HZ42E Regency Horizon™ Gas Fireplace
INSTALLATION
OPTIONAL LIGHT INSTALLATION
4) Remove the glass door - see instructions in manual.
HZ42 Accent Light Assembly Kit # 596-959
1
910-814
Plug wiring + gasket
2
910-997
Halogen Bulb
5) Remove the glass crystals/optional ceramic stones or pebbles- if
installed.
2
940-363
Amber Glass
6) Remove the inner panels if installed - see instructions in manual.
1
Light Assembly
Includes gaskets (x2)
1
918-828
Instruction Sheet
7) Remove the bottom cover - shown below.
Plug Wiring
Light Diffuser
Amber Glass
Important: 120 Volt AC power is required for the optional light.
The receptacle box will be installed on the lower left corner of
the unit and will need to be wired by a qualified electrician prior
to the optional light installation. The neutral (wider) slot of the
polarized receptacle should be at the top. A wall mounted switch
should be installed to turn the accent lighting on/off.
See wiring diagram in the instruction manual.
Bottom Cover
8) Loosen the 3 screws securing burner - slide burner to the left
and lift out - shown below.
1) Shut off electrical supply.
If faceplate is already installed - follow steps 2 & 3.
2) Remove faceplate by lifting up off glass door - see below.
3) Slide out bottom faceplate panel - see below.
Burner
Glass Door
Faceplate
9) Remove cover plate located on the left side of the firebox floor
by removing 4 screws. Discard the cover plate and gasket - keep
the screws.
Cover
Plate
Bottom
Faceplate Panel
HZ42E Regency Horizon™ Gas Fireplace
43
INSTALLATION
10) Feed the plug wiring through the opening in the
firebox - secure light assembly mounting plate and gasket
with 4 screws from the cover plate in step 9.
14) Place gasket over the inside perimeter of the light diffuser box.
15) From outside the firebox -Install light assembly box and
gasket into opening created from the removal of the cover plates
open end up - as shown below.
11) Remove the 2 cover plates and gaskets located in the lower front of the
firebox by removing 4 screws from each plate - see below.
Discard cover plates and gaskets - keep the screws.
12) Remove one screw securing the socket end of the diffuser and
separate the 2 parts - as shown below.
16) Secure the light diffuser in place with the 4 screws set aside from
the cover plates.
Screws secured from outside
the firebox.
17) Slide amber glass into light diffuser to reinstall.
13) Remove the amber glass - by sliding out.
18)
Install bulb into the socket end of assembly - as shown below.
Note: Oils from hands will shorten the life of the bulbs,
do not handle bulbs with bare hands.
44
HZ42E Regency Horizon™ Gas Fireplace
INSTALLATION
19)
20)
Install socket and bulb into light diffuser as shown below.
3) Pull out light diffuser.
Secure socket to light diffuser with one screw - as shown below.
4) Remove one screw securing the socket end of the diffuser and
separate the 2 parts - as shown below.
21) Repeat steps 12-20 to install 2nd light diffuser .
22) Plug light assembly into receptacle located in the lower left corner
inside the unit, attach ground wire to ground lug - located forward of
the receptacle.
Ground
Receptacle
23) Reconnect electrical supply - test lights.
24) Reverse steps 8 -2.
5) Replace bulb.
Note: Oils from hands will shorten the life of the bulbs,
do not handle bulbs with bare hands.
BULB REPLACEMENT
1) Slide out bottom faceplate panel - see step 3 from previous page.
2) Remove 4 screws securing light diffuser mounting plate.
6) Reverse steps 3 through 1..
HZ42E Regency Horizon™ Gas Fireplace
45
INSTALLATION
GLASS CRYSTALS OR OPTIONAL STONES
INSTALLATION ON BURNER
Spread the Glass Crystals or Stones evenly over the burner. Ensure the crystals/stones do not overlap excessively as this will affect the flame pattern.
IMPORTANT NOTE:
Only the supplied approved Glass Crystals and Stones are to be used with these fireplaces. Use of any other type of glass crystals or stones can
alter the unit's performance, any damage caused by the use of any unapproved glass or stones will not be covered under warranty.
When using Ceramic Spa/Volcanic Stones DO NOT cover burner ports or pilot light that lead to pilot flame.
BURNER PACKAGES
Unit
*Glass Crystals
Stones - Spa / Ceramic / Volcanic
E18
5lbs
5lb Glass + 70 spa stones or 1 Box Volcanic stones
GF900C (AUS)
10lbs (2lbs burner + 8lbs firebox) 10 lb Glass + 32 Volcanic Stones
HZ54E
3 lbs
1 lb Glass + 2 packages (140 Spa Stones)
2 lb Glass + 35 Ceramic Stones or 2 lb Glass + 40 Volcanic Stones
HZ42 / HZ42E
2 lbs
1 lb Glass + 1 package (70 Spa Stones)
HZ42ST / HZ42STE
2 lbs
1 lb Glass + 1 package (70 Spa Stones)
HZ30E **
1 lb
1 lb Glass + 1 package (70 Spa Stones)** / 1 lb Glass + 30 Volcanic Stones
1 lb Glass + 24 Ceramic Stones
HZ40E
2lbs
1.5 lb Glass + 30 Ceramic Stones or 1.5 lb Glass + 25 Volcanic Stones
HZ33CE
4lbs
4 lb Glass + 1 package (70 Spa stones) 4 lb Glass + 20 Volcanic Stones
4 lb Glass + 16 Ceramic Stones
HZI234E ***
3/4 lb
3/4 lb Glass + 1 package 70 Spa Stones)***
HZI390EB / HZI390PB
7 lbs [4 lbs burner + 3 lbs firebox] 2 lb Glass + 1 package (70 Spa Stones)
HZI540EB
HZI540PB
10 lbs [5 lbs burner + 5 lbs firebox] 10 lb Glass + 1 package (70 Spa Stones) / 2 lb Glass + 40 Volcanic Stones
2 lb Glass + 30 Ceramic Stones
HZO42/HZO42 (AUS)
3 lbs
3 lb Glass + 35 Volcanic stones
HZO42 (AUS)
3 lbs
3 lb Glass + 50 Garden Stones
HZ965
12 lbs
2 package Spa Stones = (140 spa stones)
PTO28CIT
5 lbs
5 lb Glass + 14 Volcanic Stones (Recommended)
PTO28 Burner Only
6 lbs
6 lb glass + 14 Volcanic Stones (Recommended)
PTO30 / Plateau Series
10 lbs
1 Box Volcanic Stones
PTO60
20 lbs
2 Boxes Volcanic Stones
NOTE: * Glass Crystals are not supplied with the unit. Must purchase separately - see quantities above.
Glass Crystals are available in 1lb and 5lb bags.
Note: 1 Spa stone package contains 70 stones.
**
Recommended - use only 40 of the 70 spa stones on the HZ30E burner.
*** Recommended - use only 24 of the 70 spa stones on the HZI234E burner.
OPTIONAL PEBBLES / GLASS CRYSTAL INSTALLATION FOR FIREBOX BASE (AROUND BURNER)
There are 2 optional packages to choose from to cover the firebox base:
1) Natural River Pebbles
2) Glass Crystals (4 colors available)
Spread the pebbles / crystals evenly on the exposed base of the firebox. Pebbles are NOT to be placed anywhere on the burner or over top of
the Glass Crystals or optional Stones.
IMPORTANT NOTE: Only the supplied and approved pebbles / glass crystals are to be used with these fireplaces. Use of any other type of pebbles,
glass crystals or other material can create a danger and will void the warranty.
Firebox (Around Burner) Packages
Unit
46
Glass Crystals
Pebbles
HZ54E / HZ54EPV
6 lbs
2 packages (6 x bags pebbles)
HZ42 / HZ42E / HZ40E
5 lbs
2 packages (6 x bags pebbles)
HZ42ST / HZ42STE / HZ42STEPV
5 lbs
2 package (6 x bags pebbles)
HZ30E
2 lbs
1 package (3 x bags pebbles)
HZI540E
3 lbs
1-2/3 packages (5 x bags pebbles)
HZI390E /HZI390PB
3 lbs
1 package (3 x bags pebbles)
HZI234E
2 lbs
1 package (3 x bags pebbles)
HZO42 / HZO42 (AUS)
3 lbs
1 package (3 x bags pebbles)
HZ42E Regency Horizon™ Gas Fireplace
INSTALLATION
Glass Crystals shown on Burner
For Units HZ54E, , HZ42ST, HZ42STE, HZI234E, HZ42E, HZ42,
HZ30E,
HZO42, HZO42 (AUS) PTO30, PTO60, Plateau Series
Optional Spa Stones + Glass Crystals shown on burner.
For Units HZ54E, HZ42ST, HZ42STE, HZI234E, HZ42, HZ42E,
HZ30E
Natural River Pebbles shown surrounding the a Horizon Burner
Glass Crystals shown surrounding the Burner
Glass Crystals shown on Burner and Firebox Floor
For Units HZI390E, HZI540E
DO NOT block pilot area with glass crystals
HZ42E Regency Horizon™ Gas Fireplace
47
INSTALLATION
GLASS DOOR INSTALLATION
Hook top of
door onto
top flange
Flush
Door
Diagram 1
Diagram 2
Diagram 3
48
HZ42E Regency Horizon™ Gas Fireplace
INSTALLATION
FACEPLATE INSTALLATION
1) Hook the flange on the back of the faceplate over the top edge of
the glass door - as shown below.
The bottom panel of the faceplate installs on the unit with 2 slides.
These slides are located in the bottom of the unit - already installed
within the outer slide. The inner slides need to be removed to install
them on the brackets.
3) Pull out inner slide from the outer slide.
4) Push done on the black lever on the outside of the inner slide - this will
release the inner slide. Pull inner slide completely out - from outer slide.
Faceplate
Glass Door
2) The height at which the faceplate sits may be adjusted to maintain
an even space between the upper faceplate and
lower faceplate panel.
5) Lay out the brackets for the lower faceplate to identify the left and
right brackets.
The upper faceplate can be raised up once the
lower faceplate panel is in position - by adjusting the 2 screws
at the back of the upper faceplate - see below
(requires an extended phillips head screw driver)
.
Left Bracket
Right Bracket
6) Install the brackets onto the lower faceplate.
Note: Installation location of the left and right brackets is the same for
both the HZ42 and HZ42ST.
Top of lower
faceplate
Right bracket shown in position on lower faceplate.
HZ42E Regency Horizon™ Gas Fireplace
49
INSTALLATION
7) Secure each bracket with 4 screws in locations shown below.
Top of lower
faceplate
HZ42ST - install slider with flat
side facing inwards
-secure with 2 screws in
locations shown.
Screw locations.
8) Install the inner slide removed from Step 4 to the bracket.
Note: Installation locations of the slide are different for the HZ42 and
HZ42ST - read instructions carefully.
10) With brackets and inner slides attached to the lower faceplate
panel - guide the lower faceplate panel into the outer slides located
in the bottom part of the unit. See inset.
Push in until flush with upper faceplate.
HZ42 - install slider on
this side of the bracket.
HZ42 -
Install slider with flat
side facing outward
-secure with 2 screws
in locations shown.
To adjust the space between the upper faceplate and the lower
faceplate panel - see step 2.
11) Final installation of faceplate on HZ42 unit
HZ42ST - install
slider on this side of the
bracket.
Note: Two faceplates need to be installed on the HZ42 ST unit.
50
HZ42E Regency Horizon™ Gas Fireplace
OPERATING INSTRUCTIONS
OPERATING
INSTRUCTIONS
LIGHTING
PROCEDURE
1) Read and understand these instructions
before operating this appliance.
IMPORTANT
To ignite or reignite the pilot, you
must first remove the glass door.
2) Check to see that all wiring is correct and
enclosed to prevent possible shock.
3) Check to ensure there are no gas leaks.
1) Press and release on ON/OFF button once
on the remote control or ON/OFF switch.
4) Make sure the glass in the glass door frame
is properly positioned. Never operate the
appliance with the glass removed.
2) After approximately 4 seconds the spark
ignition system will spark for 60 seconds to
light the main burner.
5) Verify that the venting and cap are
unobstructed.
3) The unit will turn on.
6) The unit should never be turned off, and on
again without a minimum of a 60 second
wait.
FIRST FIRE
The FIRST FIRE in your heater is part of the
paint curing process. To ensure the paint is properly cured, it is recommended you burn your
fireplace for at least four (4) hours the first time.
When first operated, the unit will release an
odour caused by the curing of the paint and the
burning off of any oils remaining from manufacturing. Smoke detectors in the house may go off
at this time. Open a few windows to ventilate
the room for a couple of hours. The glass may
require cleaning.
NOTE: When the glass is cold and the appliance
is lit, it may cause condensation and fog
the glass. This condensation is normal
and will disappear in a few minutes as
the glass heats up.
DO NOT ATTEMPT TO CLEAN THE
GLASS WHILE IT IS STILL HOT!
DO NOT BURN THE UNIT WITHOUT THE
GLASS DOOR IN PLACE.
Note: The first try for ignition will last approximately 60 seconds. If there is no flame ignition
(rectification) the board will stop sparking for
approximately 35 seconds. After wait time
, the board will start second try for ignition
by sparking for approximately 60 seconds .
If there is still no positive ignition the board
will go into lock out.
The system will need to be reset as follows:
a) Turn the system off using ON/OFF switch
or press ON/OFF button - if using optional
remote.
b) After approximately 2 seconds turn on ON/
OFF switch or press ON/OFF button if using
optional remote.
c) Repeat step 2.
NORMAL OPERATING
SOUNDS OF
GAS APPLIANCES
It is possible that you will hear some sounds from
your gas appliance. This is perfectly normal due to
the fact that there are various gauges and types
of steel used within your appliance. Listed below
are some examples. All are normal operating
sounds and should not be considered as defects
in your appliance.
Burner Tray:
The burner tray is positioned directly under the
burner and is made of a different gauge material
from the rest of the firebox and body. Therefore,
the varying thicknesses of steel will expand and
contract at slightly different rates which can cause
"ticking" and "cracking" sounds. You should also
be aware that as there are temperature changes
within the unit these sounds will likely re-occur.
Again, this is normal for steel fireboxes.
Pilot Flame:
While the pilot flame is on it can make a very
slight "whisper" sound.
Gas Control Valve:
As the gas control valve turns ON and OFF, a
dull clicking sound may be audible, this is normal
operation of a gas regulator or valve.
Unit Body/Firebox:
Different types and thicknesses of steel will
expand and contract at different rates resulting
in some "cracking" and "ticking" sounds will be
heard throughout the cycling process.
SHUTDOWN
PROCEDURE
1) Turn the wall mounted switch or remote to
the "OFF" position.
2) Press "OFF" on the remote control.
3) Turn the gas control knob to the "OFF" position to turn off the pilot.
During the first few fires, a white film
may develop on the glass front as part of
the curing process. The glass should be
cleaned after the unit has cooled down
or the film will bake on and become very
difficult to remove. Use a non-abrasive
cleaner and DO NOT ATTEMPT TO CLEAN
THE GLASS WHILE IT IS HOT.
HZ42E Regency Horizon™ Gas Fireplace
51
OPERATING INSTRUCTIONS
COPY OF LIGHTING PLATE INSTRUCTIONS
FOR YOUR SAFETY READ BEFORE LIGHTING
This appliance must be installed in accordance with local codes, if any;
if none, follow the National Fuel Gas Code, ANSI Z223.1/NFPA 54, or
Natural Gas and Propane Installation Codes, CSA B149.1.
WARNING: If you do not follow these instructions exactly, a fire or explosion may result
causing property damage, personal injury or loss of life. Improper installation, adjustment,
alteration, service or maintenance can cause injury or property damage. Refer to the owner’s
information manual provided with this appliance. For assistance or additional information
consult a qualified installer, service agency or gas supplier.
AVERTISSEMENT. Quiconque ne respecte pas à la lettre les instructions dans la présente notice
risquede déclencher un incendie ou une explosion entraînant des dommages, des blessures ou
la mort.
Une installation, d'ajustement, de modification, de service ou d'entretien peut provoquer
des blessures ou des dommages matériels. Reportez-vous au manuel du propriétaire de
l'information fournie avec cet appareil. Pour obtenir de l'aide ou des informations supplémentaires consulter un installateur qualifié, une agence de service ou fournisseur de gaz.
A) This appliance is equipped with an ignition device which automatically lights the pilot.
Do not try to light the pilot by hand.
B) BEFORE OPERATING smell all around the appliance area for gas. Be sure to smell next to the floor
because some gas is heavier than air and will settle on the floor.
WHAT TO DO IF YOU SMELL GAS
- Do not try to light any appliance.
- Do not touch any electric switch, do not use any phone in your building.
- Immediately call your gas supplier from a neighbours phone. Follow the gas supplier’s instructions.
- If you cannot reach your gas supplier, call the fire department.
C) Do not use this appliance if any part has been under water. Immediately call a qualified service
technician to inspect the appliance and replace any part of the control system and any
gas control which has been underwater.
A) Cet appareil est muni d’un dispositif d’allumage qui allume automatiquement la veilleuse.
Ne tentez pas d’allumer la veilleuse manuellement.
B) AVANT DE FAIRE FONCTIONNER, reniflez tout autour de l’appareil pour déceler une odeur
de gaz. Reniflez près du plancher, car certains gaz sont pluslourds que l’air et peuvent
s’accumuler au niveau du sol.
QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ :
• Ne pas tenter d’allumer d’appareil
• Ne touchez à aucun interrupteur; ne pas vous servir des téléphones se trouvant dans le
bâtiment.
• Appelez immédiatement votre fournisseur de gaz depuis un voisin. Suivez les
instructions du fournisseur.
• Si vous ne pouvez rejoindre le fournisseur, appelez le service des incendies
C) N’utilisez pas cet appareil s’il a été plongé dansl’eau, même partiellement. Faites inspecter l’appareil par un technicien qualifié et remplacez toute partie du système de contrôle et toute commande qui ont été plongés dans l’eau.
CAUTION: Hot while in operation. Do not touch. Severe Burns may result. Due to high surface
temperatures keep children, clothing and furniture, gasoline and other liquids having flammable
vapors away. Keep burner and control compartment clean. See installation and operating
instructions accompanying appliance.
LIGHTING INSTRUCTIONS
s
1) Turn on ON/OFF switch
2) After approximately 4 seconds the spark ignition system will spark for 60 seconds to light the main
burner.
3) The unit will turn on.
Note: The first attempt to ignition will last approximately 60 seconds. If there is no flame ignition (rectification) the board will stop sparking for approximately 35 seconds. After this wait time, the board will start a
second try for ignition by sparking for approximately 60 seconds. If there is still no positive ignition after the
second attempt the board will go into lock out.
The system will need to be reset as follows (after going into lock out mode):
a) Wait 5 minutes - turn the system off using ON/OFF switch.
b) After approximately 2 seconds turn on ON/OFF switch or press ON/OFF button if using optional
remote.
c) Unit will repeat step 2.
1) Appuyez le bouton ON / OFF
2) Attendre 4 secondes. Le système d’allumage produira des étincelles pendant 60 secondes afin d’amorcer
le brûleur principal.
3) Les flammes s’allumeront.
Remarque : Au premier allumage, le système tente d’allumer les flammes pendant 60 secondes. Si l’essai est
infructueux, le système fait une pause de 35 secondes. C’est ce qu'on appelle l'étape de rectification. Ce délai
écoulé, le système tente à nouveau d'allumer les flammes en produisant des étincelles pendant 60 secondes.
Si les flammes ne s’allument toujours pas, le système se met en mode verrouillage.
Il faut alors le réinitialiser en suivant les étapes ci-dessous (pour le déverrouiller) :
a) Attendre 5 minutes et éteindre l’appareil en réglant l’interrupteur à la position « OFF »;
b) Attendre 2 secondes et rallumer le système à l’aide de l’interrupteur ou de la télécommande.
c) L'unité répétera l'étape 2.
TO TURN OFF GAS APPLIANCE
1)
2)
Turn off ON/OFF switch
If service is to be performed - you must disconnect power to the unit, from the battery pack, refer to
manual.
1)
2)
Appuyez sur le bouton ON / OFF
Si le service est effectuée, vous devez débrancher l'appareil, du bloc-piles, voir le manuel d'instruction
pour plus de détails.
DO NOT REMOVE THIS INSTRUCTION PLATE
52
918-628b
HZ42E Regency Horizon™ Gas Fireplace
MAINTENANCE
MAINTENANCE
INSTRUCTIONS
GENERAL VENT
MAINTENANCE
1) Always turn off the gas and electrical supply
before cleaning. For relighting, refer to
lighting instructions. Keep the burner and
control compartment clean by brushing and
vacuuming at least once a year.
Conduct an inspection of the venting system
semi-annually. Recommended areas to inspect
as follows:
2) Clean appliance and door with a damp
cloth (never when unit is hot). Never use
an abrasive cleaner. The glass should be
cleaned with a gas fireplace glass cleaner.
The glass should be cleaned when it
starts looking cloudy.
3) The faceplate is finished in a heat resistant
paint and should only be refinished with heat
resistant paint. Regency® uses StoveBright
Paint - Metallic Black #6309.
Note: Faceplates and inner panels made
from stainless steel will naturally
change color over time.
4) Make a periodic check of burner for proper
position and condition. Visually check the
flame of the burner periodically, making sure
the flames are steady; not lifting or floating.
If there is a problem, call a qualified service
person.
5) The appliance and venting system must be
inspected before use, and at least annually,
by a qualified field service person, to ensure
that the flow of combustion and ventilation
air is not obstructed.
Note: Never operate the appliance without
the glass properly secured in place.
6) Do not use this appliance if any part has been
under water. Immediately call a qualified
service technician to inspect the appliance
and to replace any part of the control system
and any gas control which has been under
water.
7) In the event this appliance has been
serviced check that the vent-air system
has been properly resealed & reinstalled
in accordance with the manufacturer's
instructions.
1) Check the Venting System for corrosion in areas
that are exposed to the elements. These will
appear as rust spots or streaks, and in extreme
cases, holes. These components should be
replaced immediately.
2) Remove the Cap, and shine a flashlight down
the Vent. Remove any bird nests, or other
foreign material.
3) Check for evidences of excessive condensation,
such as water droplets forming in the inner
liner, and subsequently dripping out the joints,
Continuous condensation can cause corrosion
of caps, pipe, and fittings. It may be caused
by having excessive lateral runs, too many
elbows, and exterior portions of the system
being exposed to cold weather.
4) Inspect joints, to verify that no pipe sections or
fittings have been disturbed, and consequently
loosened. Also check mechanical supports
such as Wall Straps, or plumbers' tape for
rigidity.
GLASS GASKET
If the glass gasket requires replacement use a
tadpole glass gasket (Part # 936-159).
GLASS DOOR
Your Regency ® fireplace is supplied with
high temperature 5mm-Ceramic glass. If
your glass requires cleaning, we recommend
using an approved glass cleaner available at
all authorized dealers. Do not use abrasive
materials.
CAUTION & WARNINGS:
* Do not clean when the glass is hot.
* The use of substitute glass will void all product
warranties.
* Care must be taken to avoid breakage of the
glass.
* Do not strike or abuse the glass.
* Do not operate this fireplace without the glass
front or with a cracked or broken glass front.
* Wear gloves when removing damaged or
broken glass.
* Replacement of the glass panel(s) should be
done by a licensed or qualified service per
son.
GLASS REPLACEMENT
In the event that you break your glass by impact,
purchase your replacement from an authorized
Regency® dealer only.
Replacement neo-ceramic glass is shipped
with gasket.
CAUTION: Wear gloves when
removing damaged or broken glass.
WARNING: Do not operate the
appliance with the glass panels
removed, cracked or broken.
Replacement of the glass panels
should be done by a licensed or
qualified service person.
8) Verify operation after servicing.
HZ42E Regency Horizon™ Gas Fireplace
53
MAINTENANCE
GLASS DOOR REMOVAL
1) Turn the unit off and allow it to cool down to
room temperature.
2) Turn off the gas supply to the unit.
3) Remove the faceplate by lifting it up off the
glass door.
Faceplate
Glass Door
4) Remove the glass door.
a) Remove the 3 screws shown below
at the bottom of the glass door.
b) Swing the door out 45o from the bottom
and lift up and out.
54
HZ42E Regency Horizon™ Gas Fireplace
MAINTENANCE
VALVE ASSEMBLY REPLACEMENT
1) Turn the unit off and allow it to cool down to room temperature.
6) Lift out firebox base cover.
2) Turn off the gas and power supply to the unit.
3) Remove the faceplate by lifting it up off the glass door.
7) Remove three screws from locations shown below to release
burner.
Slide burner to the left to release from the orifice and lift out see inset.
Faceplate
Glass Door
4) Remove the glass door.
a) Remove the 3 screws shown below at the bottom of the glass
door.
b) Swing the door out 45o from the bottom and lift up and out.
8) Remove the valve tray by undoing the 14 outer screws.
Note: Some of the screws are not visible in Diagram below.
Note: If optional accent lights have been installed - assure all wiring is out
of the way before removing valve assembly.
5) Remove the pilot cover as shown below.
HZ42E Regency Horizon™ Gas Fireplace
55
MAINTENANCE
BULB REPLACEMENT
9) Partially lift out valve tray.
1) Slide out bottom faceplate panel.
2) Remove 4 screws securing light diffuser mounting plate - see below.
3) Pull out light diffuser.
Gas Line
10) Disconnect the inlet gas line and remove the valve assembly.
11) Replace valve assembly and reverse steps.
4) Remove one screw securing the socket end of the diffuser and
separate the 2 parts - as shown below.
5) Replace bulb.
Note: Oils from hands will shorten the life of the bulbs,
do not handle bulbs with bare hands.
56
HZ42E Regency Horizon™ Gas Fireplace
PARTS LIST
MAIN ASSEMBLY
Part #
Description
2) 910-078
910-363
910-366
Battery AA
White Wall Switch
White Switch Plate Wire
3) 596-008
Bottom Cover NG / LP
4) 596-525
596-530
5) 596-574/P
596-576/P
6) 911-004
911-005
7) 911-006
911-007
8) 904-593
904-345
9) 948-484
Burner Assembly -NG
Burner Assembly-LP
Valve Assembly -NG
Valve Assembly-LP
886 Sit Valve - NG
886 Sit Valve - LP
Pilot Assembly - NG
Pilot Assembly - LP
Orifice # 40 (NG)
Orifice # 53 (LP)
Slide Hinge
904-658
430-011
596-047F
596-048
596-089
430-011
586-017F
586-016F
596-068
596-045
596 072
Inlet Gas Flex Line SS
Flue Collar Gasket
Relief plate door
Plate Relief Gasket
Valve Tray Gasket
Inner Flue Collar Gasket
Flue Restrictor Plate
Gas line cover
Top nailing strip
Side nailing strip
Bottom nailing strip
940-361/P
586-029
Flush Glass / c/w gasket
Flush Glass Frame (shown on next page)
910-882
Wire (Valve to Burner ON/OFF)
918-932
Manual
7
9
3
4
8
5
6
HZ42E Regency Horizon™ Gas Fireplace
57
PARTS LIST
Part #
Description
10) 596-907
596-908
Reflective Stainless Steel Inner Panels
Black Enamel Inner Panels
11) 586-914
586-916
586-917
Faceplate Black
Faceplate Sunset Bronze
Faceplate Brushed Stainless
946-671
946-672
946-673
946-674
Cobalt Blue Glass Crystals
Natural River Pebbles
White River Pebbles
Ceramic Spa Stones
946-680
946-681
946-683
946-684
910-574
910-576
910-572
GT Proflame Remote Control
GTM Proflame Remote Control
GTM NG Modulator
GTM LP Modulator
GTM Wire Harness
Cover Wall Mount (white)
Receiver GTM SIT w/Batt & Cover
10
11
58
HZ42E Regency Horizon™ Gas Fireplace
WARRANTY
Regency® Fireplace Products are designed with reliability and simplicity in mind. In addition, our internal Quality Assurance Team carefully inspects each unit thoroughly
before it leaves our facility. Regency® Fireplace Products is pleased to extend this limited lifetime warranty to the original purchaser of a Regency® Product. This warranty
is not transferable.
The Warranty: Limited Lifetime
The combustion chamber, heat exchanger, burner tubes/pans, logs, glass crystals, ceramic spa stones, pebbles, brick panels and gold plating (against defective manufacture only) are
covered under the Limited Lifetime Warranty for five (5) years for parts and subsidized labour* and parts only thereafter.
Glass is covered for lifetime against thermal breakage only, parts and subsidized labour* for five (5) years and parts only thereafter from date of purchase.
External casting, surrounds and grills are covered against cracks and warps resulting from manufacturer defects, parts and subsidized labour* for three (3) years from the date of purchase
and parts only thereafter.
Special Finishes - One year on stainless steel panels, nickel overlays,nickel faceplates, brushed nickel and antique copper full screens and doors. You can expect some changes in color
as the product "ages" with constant heating and cooling. Regency warranties the product for any manufacturing defects on the original product. However, the manufacturers warranty does
not cover changing colors and marks, ie. finger prints, etc applied after the purchase of the product. Damage from the use of abrasive cleaners is not covered by warranty.
Electrical and mechanical components such as blowers, switches, wiring, thermodiscs, Regency® remote controls, spill switches, thermopiles, thermocouples, pilot assembly components,
and gas valves are covered for two years parts and one year subsidized labour* from the date of purchase. Blowers and valves replaced under warranty are considered repairs and continue
as if new with appliance. ie. twelve (12) months from original purchase date of appliance with a minimum of three (3) months coverage from date of replacement.
Regency venting components are covered parts and subsidized labour* for three (3) years from date of purchase.
Simpson Dura-Vent venting components (Direct Vent units) are covered by Simpson Dura-Vent Inc. warranty.
Repair/replacement parts purchased by the consumer from Regency® after the original coverage has expired on the unit will carry a 90 day warranty, valid with a receipt only. Any item
shown to be defective will be repaired or replaced at our discretion. No labor coverage is included with these parts.
Conditions:
Any part or parts of this unit which in our judgement show evidence of such defects will be repaired or replaced at Regency's option, through an accredited distributor or agent provided that
the defective part be returned to the distributor or agent Transportation Prepaid, if requested.
Porcelain/Enamel - Absolute perfection is either guaranteed nor commercially possible. Any chips must be reported and inspected by an authorized dealer within three days of installation.
Reported damage after this time will be subject to rejection.
It is the general practice of Regency® to charge for larger, higher priced replacement parts and issue credit once the replaced component has been returned to Regency and evaluated for
manufacturer defect.
The authorized selling dealer is responsible for all in-field service work carried out on your Regency® product. Regency will not be liable for results or costs of workmanship from unauthorized
service persons or dealers.
At all times Regency reserves the right to inspect product in the field which is claimed to be defective.
All claims must be submitted to Regency® by authorized selling dealers. It is essential that all submitted claims provide all of the necessary information including customer name, purchase
date, serial #, type of unit, problem, and part or parts requested, without this information the warranty will be invalid.
Exclusions:
This limited Lifetime Warranty does not extend to or include paint, door or glass gasketing or trim.
At no time will Regency® be liable for any consequential damages which exceed the purchase price of the unit. Regency® has no obligation to enhance or modify any unit once manufactured.
ie. as products evolve, field modifications or upgrades will not be performed.
Regency® will not be liable for travel costs for service work.
Installation and environmental problems are not the responsibility of the manufacturer and therefore are not covered under the terms of this warranty policy.
Embers, rockwool, gaskets, door handles and paint are not covered under the terms of this warranty policy.
Any unit which shows signs of neglect or misuse is not covered under the terms of this warranty policy.
The warranty will not extend to any part which has been tampered with or altered in any way, or in our judgment has been subject to misuse, improper installation, negligence or accident,
spillage or downdrafts caused by environmental or geographical conditions, inadequate ventilation, excessive offsets, negative air pressure caused by mechanical systems such as furnaces,
fans, clothes dryer, etc.
Freight damage to stoves and replacement parts is not covered by warranty and is subject to a claim against the freight carrier by the dealer.
Regency will not be liable for acts of God, or acts of terrorism, which cause malfunction of the appliance.
Performance problems due to operator error will not be covered by this warranty policy.
Products made or provided by other manufacturers and used in conjunction with the operation of this appliance without prior authorization from Regency®, may nullify your warranty on
this product.
Any alteration to the unit which causes sooting or carboning that results in damage to the interior / exterior facia is not the responsibility of Regency® .
HZ42E Regency HorizonTM Gas Fireplace
59
Register your Regency® warranty online
www.regency-fire.com
Reasons to register your product online today!
• View and modify a list of all your registered products.
• Request automatic email notification of new product updates.
• Stay informed about the current promotions, events, and special
offers on related products.
Installer: Please complete the following information
Dealer Name & Address: ______________________________________________
___________________________________________________________________
Installer: ___________________________________________________________
Phone #: ___________________________________________________________
Date Installed: ______________________________________________________
Serial No.: __________________________________________________________
Regency Horizon is a trademark of FPI Fireplace Products International Ltd.
© Copyright 2013, FPI Fireplace Products International Ltd. All rights reserved.
Printed in Canada
Download PDF