AMX | NXA-ENET8-2POE | Quick Start Guide

Quick Start Guide
MST-1001 10.1” Modero S Series® Tabletop Touch Panel
Overview
Series®
The Modero S
is a beautiful touch panel family sophisticated enough for
room control yet priced right for the most cost sensitive installations. The
MST-1001 10.1” Modero S Series Tabletop Panel (FG2265-05) includes VoIP,
brilliant 24-bit color depth, PoE connectivity, Bluetooth, USB and streaming
video.
Microphone
Sleep/Settings Button
Note: For more information on installation and configuration, as well as
complete specifications on this device, please refer to the MSD/T-1001
Operation/Reference Guide, available at www.amx.com.
Note: Optimal performance requires use of one of the following AMX PoE power
supplies (not included):
• PS-POE-AF-TC, PoE Injector, 802.3AF Compliant (FG423-83)
• NXA-ENET8-2POE, Gigabit PoE Ethernet Switch (FG2178-63)
Note: AMX does not support the use of non-AMX power supplies.
Panel Connectors and Wiring
FIG. 1 shows the connectors located on the back of the MST-1001.
Power for the MST-1001 via Power Over Ethernet
Power for the MST-1001 is supplied via Power Over Ethernet (PoE), utilizing an
AMX-certified PoE injector such as the PS-POE-AF-TC PoE Injector
(FG423-83) or other approved AMX PoE power source. The incoming Ethernet
cable should be connected to the RJ-45 port on the MST-1001.
Configuring the MST-1001
(Front)
Microphone
Sleep Button
The MST-1001 is equipped with Settings Pages that allow you to set and
configure various features on the panel. For more information on connecting and
configuring the MST-1001 to a network, please refer to the Modero S Series
Programming Guide, available at www.amx.com.
Accessing the Settings Pages
To access the Settings Pages on the MST-1001, press and hold the Sleep/
Settings Button (FIG. 1) on the top of the panel for 3 seconds. The user will be
prompted to release the button to enter the Settings page (FIG. 2).
USB Port
Speaker
(Rear)
RJ-45 Port
FIG. 1 MST-1001
Product Specifications
MST-1001 Specifications
FIG. 2 Settings page
Power:
PoE (Power over Ethernet), 802.3af, class 0
Accessing the Configuration Page
Power Consumption:
•
•
•
•
Full-On: 14 W maximum
Standby: 4.5 W
Shutdown: 0.7 W
Startup Inrush Current: Not Applicable due to PoE
standard
1.
Operating Environment:
•
•
•
•
•
Operating Temperature: 32° F to 104° F (0° C to 40° C)
Storage Temperature: 4° F to 140° F (-20° C to 60° C)
Humidity Operating: 20% to 85% RH
Humidity Storage: 5% to 85% RH
Power (“Heat”) Dissipation: On: 10.9 BTU/hr, Standby:
10.6 BTU/hr
Dimensions (HWD):
6.18" x 10.04" x 4.06" (15.69 cm x 25.51 cm x 10.32 mm)
Weight:
2.60 lbs (1.18 Kg)
Certifications:
•
•
•
•
•
•
•
•
Included Accessories:
UL
FCC Part 15 Class B
C-Tick CISPR 22 Class B
CE EN 55022 Class B and EN 55024
CE EN 60950-1
IC CISPR 22 Class B
VCCI CISPR 22 Class B
RoHS/WEEE compliant
• USB port cover kit (FG5968-18)
• CATE5 Ethernet Cable, Flat Black (ECA2265-10)
• UTP CAT.5E Snap In Coupler, Black (64-5968-01)
2.
From the Settings Page, select Configuration. If the Configuration page is
password protected, this opens a password keypad.
Enter the panel password into the keypad (the default is 1988) and select
OK to access the page (FIG. 3).
FIG. 3 Configuration page
3.
To reboot the panel, press and hold the text under the Reboot section for
two seconds. To shut down the panel, press and hold the text under the
Shutdown section for two seconds.
Setting the Panel’s Device Number and Device Name
In the Configuration page:
1.
Press Panel to open the Panel Configuration page.
2.
In the Device Name page, ensure that the Synchronize Device Names
button is not selected, and click it to deselect it if it is.
3.
Press Device Number to open the Device Number keypad.
4.
Enter a unique Device Number assignment for the panel and press OK.
5.
Press the Device Name field to open the Device Name keypad.
6.
Enter a unique Device Name assignment for the panel and press OK.
7.
Click the arrow on the top left of the page once to return to the
Configuration page and twice to return to the Settings page.
3.
If you have enabled password security on your Master, you need to set the
username and password within the device.
a. Select Username to open the Master User keyboard.
b. Set your Username and select OK.
c. Select the Password to open the Master Password keyboard.
d. Set your Master Password and select OK.
e. Press the Back button twice to return to the Settings page.
Configuring the Panel to a Network
The first step is to configure the panel’s communication parameters. This only
configures the panel to communicate with a network, and it is still necessary to
tell the panel with which Master it should be communicating.
Accessing the Connection & Networks Page
Network Communication With a DHCP Address
1.
In the Connection & Networks page:
1.
Select Network Connection to open the Network Connection page
(FIG. 6).
2.
From the Settings Page, select Connection & Networks. If the page is
password protected, this opens a password keypad.
Enter the panel password into the keypad (the default is 1988) and select
OK to access the page (FIG. 4).
FIG. 4 Connection & Networks page
Connecting to a Master
The panel requires that you establish the type of connection you want to make
between it and your Master.
In the Connection & Networks page:
1.
Select Master Connection to open the Master Connection page (FIG. 5).
FIG. 6 Network Connection page
2.
3.
Toggle the DHCP/Static field until the choice cycles to DHCP. This action
causes all fields on the page (other than Host Name) to be greyed-out.
Select Host Name to open the Host Name keyboard. Enter the new host
name and click OK.
Setting Static IP Information
When using DHCP settings for a panel, the DHCP server will automatically
populate almost all of the Network Connections page fields, with the exception
of Hostname. When setting the panel for Static, however, this information must
be entered manually. To enter the network connection information:
1.
In DHCP/Static, press the field until the entry reads “Static”. This enables
all of the editable Network Connections page fields.
2.
Select the IP Address field to open the Wired IP Address keypad (FIG. 7).
FIG. 5 Master Connection page
2.
Press Mode to toggle through the available connection modes:
Connection Modes
Mode Description
Procedures
Auto
The device connects to the first
master that responds.
This setting requires that you set
the System Number.
Setting the System Number:
1. Select Master System Number to open
the keypad.
2. Set your Master System Number and
select OK.
The device connects to the
specific IP of a master via a TCP
connection.
This setting requires that you set
the Master’s IP.
Setting the Master IP:
1. Select the Master IP number to the
keyboard.
2. Set your Master IP and select OK.
The device “listens” for the
Master to initiate contact.
This setting requires you provide
the master with the device’s IP.
Confirm device IP is on the Master URL list.
You can set the Host Name on the device
and use it to locate the device on the master.
Host Name is particularly useful in the DHCP
scenario where the IP address can change.
URL
Listen
FIG. 7 Wired IP Address keyboard
3.
Enter the server’s IP address and click OK.
4.
Repeat this procedure with the other fields on the Network Connections
page.
5.
When finished, the new connection information will be visible in the
Network Connections page.
For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).
1/14
©2014 AMX. All rights reserved. AMX and the AMX logo are registered trademarks of AMX.
AMX reserves the right to alter specifications without notice at any time.
3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com
93-2265-05
REV: D
Download PDF