Ricoh | FV-L500B1 | Camera Link® 5 mega-pixel Camera

Camera Link ®
5 mega-pixel Camera
5M Camera Link with highly rigid case
and compact design
FV-L500B1
5 megapixels
Camera
Link
PoCL
Use in tasks such as fault inspection, display inspection, solder defect
inspection, and high-precision flaw detection for semiconductors, liquid crystal
and plasma flat panel displays, circuit boards, etc.
35 mm×35 mm compact design
Uses PoCL (Power over Camera Link), which has a strong track record as a
high-resolution digital camera interface
High-speed frame rate of 5M: 16 fps
Various trigger modes (pulse width, edge preset trigger) as standard features
In addition to camera tripod screw holes, M4 screw holes are located on
four sides (top, bottom, left, right)
To increase mounting precision, mounting holes are arranged based on the
CCD optical axis
[Exposure-interval signal output] outputs the camera exposure interval and enables efficient inspection
[Supported cameras] FV-L500B1, FV-L200B1, FV-L030B1, FV-G200B1, FV-G030B1
Exposure-interval signal output—which can start the next exposure during the
transfer of the previous image—makes it possible to achieve high-speed work
inspection*, thereby raising inspection efficiency. In addition, since the camera
exposure interval is output externally, it can be used for various purposes.
*Limited to cases where the next exposure does not end before the completion of image transfer.
Standard
cameras
Trigger signal
CCD exposure
Camera image
output
Cameras supporting
exposure-interval
signal output
Trigger signal
CCD exposure
Camera image
output
• Exposure starts during image transfer.
The CCD exposure start marked with the
Dimensions and rear connector specifications
FV-L500B1 Product specifications
Active picture elements
±0.02
15.5
14.5
±0.05
2448 (H) × 2058 (V)
33.264 kHz
17.69 [CCD image area: in air 17.526]
64 MHz
Minimum scene illumination
Sync. System
Internal
Video output
Digital 8 , 10 or 12 bit Raw Data (Base configuration)
Shutter speed
OFF, 1/8 to 1/209,000 sec. (Variable at every H and clock)
Gain
0 to 18.309 dB
Gamma
1.0
Input voltage
12 Vdc ± 10%
Consumption
Less than 4.0 W
Power supply
35
(R1)
1/4”20UNC(Screw for Tripod)
40.7
10.5
B
A
U1(C Mount Screw)
Unit: mm
A Camera Link connector 3M-made SDR equivalent
B
Input/output signal connector
Hirose-made HR10A-7R-6PB equivalent Trigger signal input can be done in accordance with the
camera setting.Optional connector RICOH FP-CN6PB is supported.
Note: For the frame grabber board and cable, the PoCL type should be used.
1
IN/
OUT
IN
C mount
2
I/O-1
IN/OUT
Approximately 80 g
3
I/O-2
IN/OUT
35 (W) × 35 (H) × 40.7 (D) mm (excluding the connector)
Lens mount
φ2.0 Depth 2.5 H7 +0.010
0
0
φ36 −0.05
Signal
name
GND
Dimensions
Weight
4-R3
0.24 lux at F1.2
35
Pixel frequency
16 Hz
φ30
Horizontal frequency
22.7
4–M4 Depth 4
25 ±0.05
3.45 (H) × 3.45 (V) µm
Vertical frequency (Frame rate)
2.0 Depth 2.5 H7 +0.010
0
±0.05
16.8 ±0.05
15 ±0.02
Cell size
Operational
environment
17.69
2/3" interline 5.0 Mega pixels monochrome progressive CCD
2.3
Imager
is speeded up, thereby making high-speed work detection possible.
Pin No.
Operational
temperature
-5 to 40 deg. C
4
I/O-3
IN/OUT
Storage
temperature
-30 to 65 deg. C
5
6
TRIGGER
N.C.
OUT
IN
OUT
IN
OUT
IN
OUT
OUT
Voltage
Low voltage
0V
0 to +0.99V
0V
0 to +0.99V
0V
0 to +0.99V
0V
0V
High voltage
+2.3 to +3.3V
+3.3V
+2.3 to +3.3V
+3.3V
+2.3 to +3.3V
+3.3V
+3.3V
04
4575 Ruffner St., San Diego, CA 92111 | P: 858.565.1101 | T: 800.284.2288 | F: 858.565.7845 | sales@avsupply.com | www.avsupply.com
Download PDF