advertisement
V56.17.x, V56.16.x, and V56.15.6Z
Summary of Firmware Changes
This document summarizes the following V56.17.x, V56.16.x, and V56.15.x firmware releases:
Firmware
Release Date
Page
Firmware
Release Date
Page
V56.17.17Z
Release Date: 30 December 2013
This firmware release includes features of the previous V56.17.16Z release. It is for use with the following printer models:
• GX420d™
• GX420t™
• GX430t™
Changes
• Support for the wlan.power_save Set/Get/Do command has been added.
See the Zebra Programming Guide for details.
Issues Corrected
•
Updated to current ENERGY STAR
®
standards.
V56.17.16Z
Release Date: 13 June 2013
This firmware release includes features of the previous V56.17.12Z release. It is for use with the following printer models:
• GX420d™
• GX420t™
• GX430t™
© 2013 ZIH Corp. All product names and numbers are Zebra trademarks, and Zebra and the Zebra logo are registered trademarks of ZIH Corp. All rights reserved.
14588L-015 Rev. A
12/30/2013
2
Summary of Firmware Changes
V56.17.12Z
Issues Corrected
• Calibration of small height labels has been enhanced
• The printer will now report “12”when there is a label ready to be removed and the unit is in peel mode
• Improved vertical registration when in
"device.epl_legacy_mode" "registration" mode
• Handling of functions within GS128 barcodes has been improved
• Positioning of human readable text in EPL barcodes improved when the height of the barcode is larger than the length of the label
• The printer will now use the ZPL Font 0 as the default font
• Print positioning when the JB command is used has been improved
• Code 128 landscape printing improved to correct image artifact issue
• Nine digit zip codes are now correctly supported in EPL-formatted Maxicode barcodes
• When in EPL mode the R command now accepts negative values.
• Enhanced memory management to resolve text field not printing issue.
• Using embedded commands in a Field Block (^FB) field are now correctly supported.
Changes
None.
V56.17.12Z
Release Date: 21 July 2012
This firmware release includes features of the previous V56.17.11ZA release. It is for use with the following printer models:
• GX420d™
• GX420t™
• GX430t™
Issues Corrected
• Issue with labels printing out of order has been fixed
.
• When the print width is set using q command, the R command will now be set to 0,
making margin positioning backward-compatible to previous firmware versions.
• The internal wired and wireless printserver will no longer lose connectivity when a raw port other than 9100 is used.
• The issue where a printer could display a flashing Red-Green LED immediately after a power cycle has been fixed.
Changes
None.
14588L-015 12/30/2013
Summary of Firmware Changes
V56.17.11ZA
3
V56.17.11ZA
Release Date: 15 August 2011
This firmware release includes features of the previous V56.17.11Z release. It is for use with the following printer models:
• GX420d™
• GX420t™
• GX430t™
Issues Corrected
Roaming when using WEP has been improved.
Changes
None.
V56.17.11Z
Release Date: 30 June 2011
This firmware release includes features of the previous V56.17.10Z release. It is for use with the following printer models:
• GX420d™
• GX420t™
• GX430t™
Issues Corrected
• Support for using FNC1 in Code 128 now complies to AIM ITS/99-005 4 November
1999.
• When printer is configured to cutter mode, the ^LL command will now be ignored unless the value used is greater than the cutter-to-head distance, plus the max tear adjust.
• Timing issues caused by dry cut are resolved.
• Remaining number of labels after RIBBON OUT condition is now accurately reflected.
• Print position issues when printing serialized fields has been corrected.
• EPL stored forms are now being completely cleared.
• The encoding table for EPL soft fonts has been corrected.
• Print servers now properly handle fragmented TCP packets.
• The OS command has now been implemented.
• Carriage Returns and Nulls will now be ignored before processing EPL or ZPL code.
12/30/2013 14588L-015
4
Summary of Firmware Changes
V56.17.11Z
• Handling of multiple formats separated by CR/LF strings has been improved.
• A "0" will no longer be added to a Code 128 barcode when the data stream is "<T>".
• No-Motion Power Up placement has been corrected for all print modes.
• Mirroring command files with ^DFB will now store formats in B: memory correctly.
• 'R' command values are now persistent across power cycle.
• While in ZPL mode, if the print mode is set using ^MM, the selected values will carry over to EPL mode.
• The ~CONTROL value settings are now persistent through a printer power cycle
• Codablock now works correctly in conjunction with ^FT in all orientations.
• FTP connections are no longer incorrectly closed during data transmission.
• Issues found when printing via LPD have been resolved.
• Issue with wireless print servers not connecting to certain access points when using
WPA-PSK is resolved.
• Issue with authentication failure when using PEAP on IAS2008 server is resolved.
• Issue with wireless print servers losing communication for extended periods of time with certain controllers when configured for WPA-LEAP is resolved.
• Russian translations for WEB and DELAYED CUT have been updated.
• ~JS has been updated function correctly when lower case letters are used in parameters.
• Internal Print Server will now try to renew DHCP address once lease is up.
• File names with more than 8 characters will no longer be changed during the defragmentation process.
• RAM management has been improved to reduce out of memory errors.
Changes
• Added SGD command, comm.pnp_option, with two values 'on' and 'off' - with the default being 'off''.
• Added extra param to ^SC - "g" param, called "Serial PnP,” with values 'y' and 'n', defaulted to 'n'.
• Added new printhead over-temp mode, when triggered the printer LED shall blink
RED-RED-RED-Green.
Note •
If a print server is directly connected to some Cisco switches, it may be necessary to configure the “switchport” setting to “host”. Once “host” is enabled, it enables the “portfast” feature, which prevents spanning-tree topology updates from occurring. These updates are exchanged between all of the switches on the network and can cause delays.
14588L-015 12/30/2013
Summary of Firmware Changes
V56.17.10Z
5
V56.17.10Z
Release Date: 03 December 2010
This firmware release includes features of the previous V56.17.9Z release. It is for use with the following printer models:
• GX420d™
• GX420t™
• GX430t™
Issues Corrected
• Firmware downloading enhancements to improve reliability.
Changes
• None.
V56.17.9Z
Release Date: 05 August 2010
This firmware release includes features of the previous V56.17.5Z release. It is for use with the following printer models:
• GX420d™
• GX420t™
• GX430t™
Issues Corrected
• An EPL format with 2 variable fields in the barcode will now print the same size when printed consecutively and will scan properly.
• The printer will now maintain the same configuration when switching between EPL1 and
EPL2 mode.
• The internal wired 10/100 print server will now issue a DHCP Decline when a duplicate
IP address is detected.
• Unwanted characters will no longer appear on the printer's LCD display during a Mirror process.
• When the printer is configured to EPL 1 mode after a power cycle it will now remain responsive to EPL commands if a network timeout occurs.
• A printer configured for no media feed at power-up will now have the first printed label correctly positioned.
• A printer configured for no media feed at power-up should not skip labels.
12/30/2013 14588L-015
6
Summary of Firmware ChangesSGD Printer Commands
V56.17.9Z
Changes
Added SGD command, device.epl_legacy_mode, that configures the printer into
LP/TLP 2824 and LP/TLP 2844 compatibility mode for vertical registration.
Updated the ^CM Change Memory Letter Designation command to include the multiple alias parameter.
device.epl_legacy_mode
Description This command places the printer in a LP/TLP 2824 and LP/TLP 2844 compatibility mode for vertical registration.
Supported Devices
• G-Series printers
• LP2824 Plus and TLP 2824 Plus
Type getvar;setvar
Commands
getvar setvar*
Details
This command causes the printer to return the current setting for the device.epl_legacy_mode setting.
Format: ! U1 getvar "device.epl_legacy_mode"
This command instructs the printer to change the epl_legacy_mode setting.
Format: ! U1 setvar "device.epl_legacy_mode" "value"
Values:
off = epl_legacy_mode not active registration = EPL legacy registration mode on
Default Value: "epl_zpl"
Note •
For details on SGD command structure, see the Zebra Programming guide.
14588L-015
Example •
This setvar example shows setting the value to "registration".
! U1 setvar "device.epl_legacy_mode" "registration"
Note •
This setting is not defaulted as part of a factory default (^JUF or ^default). The setting is persistent across a power cycle or reset (~JR or device.reset)
When printing labels using EPL commands, printing starts 1mm from the top edge of the label
(from the gap). This is known as the "no print zone". When printing in ZT mode, the "no print zone" starts at the gap on the leading edge of the label. When printing in ZB mode, the "no print zone" starts from the gap on the trailing edge of the label. In the TLP2844, LP2844,
TLP2824, LP2824, and TLP3842 printers, the distance from gap to start of print (the "no print zone") is not always 1mm. The table below shows the nominal distance.
12/30/2013
Summary of Firmware ChangesZPL Commands
V56.17.9Z
7
Distance from Edge of Label to First Print Line (No Print Zone)
Legacy Printer
Model
New Printer Model ZT Mode
LP2844
TLP2844
TLP3842
LP2824
TLP2824
GX420, GK420 (direct thermal)
GX420, GK420 (thermal transfer)
GX430 (thermal transfer)
LP 2824 Plus (direct thermal)
TLP 2824 Plus (thermal transfer)
1.9 mm
0.4 mm
0.0 mm
1.5 mm
0.1 mm a. Setting epl_legacy_mode to "registration" selects the distance shown in the table.
b. Setting epl_legacy_mode to "off" selects a no print zone distance of 1mm.
ZB Mode
0.0 mm
1.6 mm
1.2 mm
0.4 mm
1.8 mm
^CM — Change Memory Letter Designation
Description The ^CM command allows you to reassign a letter designation to the printer’s memory devices. If a format already exists, you can reassign the memory device to the corresponding letter without forcing, altering, or recreating the format itself.
Using this command affects every subsequent command that refers to specific memory locations.
Format ^CMa,b,c,d
Parameters Details
a
= memory alias for
B:
Accepted Values:
B: , E: , R: , A: , and NONE
Default Value: B: b
= memory alias for
E:
Accepted Values:
B: , E: , R: , A: , and NONE
Default Value: E: c
= memory alias for
R:
Accepted Values:
B: , E: , R: , A: , and NONE
Default Value: R: d
= memory alias for
A:
Accepted Values:
B: , E: , R: , A: , and NONE
Default Value: A: e
= multiple alias
Accepted Values:
M , or no value
Default Value: no value
• This parameter is supported on Xi4 and ZM400/ZM600 printers using firmware V53.17.7Z or later.
• This parameter is supported on G-Series printers using firmware versions v56.17.9Z and v61.17.9Z or later.
• This parameter is supported on printers using firmware V60.17.7Z or later.
Comments Unless the e (multiple alias) parameter is used, when two or more parameters specify the same letter designator, all letter designators are set to their default values.
12/30/2013 14588L-015
8
Summary of Firmware ChangesZPL Commands
V56.17.9Z
It is recommended that after entering the ^CM command, ^JUS is entered to save changes to
EEPROM. Any duplicate parameters entered will reset the letter designations back to the default.
If any of the parameters are out of specification, the command is ignored.
Example 1 •
This example designates letter E: to point to the B: memory device, and the letter B: to point to the E:memory device.
^XA
^CME,B,R,A
^JUS
^XZ
Example 2 •
This example designates that content sent to, or read from the B: or E: memory locations will be sent to or read from the E: memory location.
^XA
^CME,E,R,A,M
^JUS
^XZ
Example 3 •
This example designates that content sent to, or read from the A: or E: memory locations will be sent to or read from the E: memory location.
^XA
^CMB,E,R,E,M
^JUS
^XZ
Example 4 •
This example designates that content sent to, or read from the A:, B: or E: memory locations will be sent to or read from the E: memory location.
^XA
^CME,E,R,E,M
^JUS
^XZ
Note •
Examples 2, 3 and 4 are the only valid uses of the multiple alias parameter.
14588L-015 12/30/2013
Summary of Firmware ChangesSGD Wireless Commands
V56.17.5Z
9
V56.17.5Z
Release Date: 18 January 2010
This firmware release includes features of the previous V56.17.3Z release. It is for use with the following printer models:
• GX420d™
• GX420t™
• GX430t™
Changes
The ip.mirror.reset_delay command allows you to configure the number of seconds between when the printer receives the last byte of the last file from the /commands directory and when the printer resets during a mirror event. This new command makes it possible to place files that require processing by the ZPL or SGD engines in the /commands directory.
Zebra recommends placing files that require processing by the ZPL or SGD engines into the
/commands directory and using the ip.mirror.reset_delay command, rather than performing character substitution on content being placed in the /files directory. The default setting for the ip.mirror.reset_delay command is 5 seconds; in some cases it may be necessary to use a longer delay to allow for full processing of longer or more complex files.
The /commands directory — with the use of the ip.mirror.reset_delay command
— is now for files that need processing by the ZPL or SGD engine. This includes:
• Stored formats using the ^DF command
• Saved formats using the ^IS command
• Graphics and font files that do need processing to be stored (content using the ~DY, ~DG,
~DS, ~DT, and ~DU commands)
The /files directory is for use with files that do not require processing by the ZPL or SGD engines. This includes:
• .ttf, .png or .bmp files (that previously would have been sent using ~DY)
• .wml files
• ZBI programs
• Wireless certificate files
• .nrd files (containing either certificate content or command content)
ip.mirror.reset_delay
Description This command specifies the number of seconds between when the printer receives the last byte of the last file from the /commands directory and when the printer resets during a mirror event.
12/30/2013 14588L-015
10
Summary of Firmware ChangesSGD Wireless Commands
V56.17.5Z
Type getvar;setvar
Note •
This command is available in V56.17.3Z, V61.17.3Z and later versions.
This table identifies the command for this format:
Commands
getvar setvar
Details
This command retrieves the number of seconds between when the printer receives the last byte of the last file from the /commands directory and when the printer resets during a mirror event.
Format: ! U1 getvar "ip.mirror.reset_delay"
This command sets the number of seconds between when the printer receives the last byte of the last file from the /commands directory and when the printer resets during a mirror event.
Format: ! U1 setvar "ip.mirror.reset_delay" "value"
Values: 0 - 900 (seconds)
Default Value: "5"
Example •
This setvar example shows the value set to "10".
! U1 setvar "ip.mirror.reset_delay" "10"
When the setvar value is set to "10", the getvar result is "10".
Note •
The default setting for the ip.mirror.reset_delay command is 5 seconds; in some cases it may be necessary to use a longer delay to allow for full processing of longer or more complex files.
Issues Corrected
• Print Server will now completely close a connection after a connection timeout.
• A print job will resume after the print head is opened, closed and an error has been cleared.
• Multiple connections being opened and closed at the same time will no longer cause labels to print out of order.
• Printer will no longer reset and lose print job when the print head is lifted in the middle of a EPL 1 print job.
• The SGD commands “interface.network.active.ip_addr” and
“interface.network.active.gateway” will now correctly reflect the active network connection.
• In EPL 1 mode, the Formfeed control character (0x0C) will now cause the printer to advance to the top of next label.
• Printer will no longer stop responding after obtaining an IP address via BOOTP when
Mirroring is enabled.
14588L-015 12/30/2013
Summary of Firmware ChangesSGD Wireless Commands
V56.17.3Z
11
• Internal Wired/Wireless Print Server will no longer send a continuous DHCP-DISCOVER when "DHCP" is the only selected addressing method.
V56.17.3Z
Release Date: 02 September 2009
This firmware release includes features of the previous V56.16.9Z release. It is for use with the following printer models:
• GX420d™
• GX420t™
• GX430t™
Changes
Wireless Markup Language (WML)
WML offers a text-based method of designing customized menus on the LCD front panel of selected printers. By leveraging Set-Get-Do (SGD) and Zebra Programming Language (ZPL) commands, menus that feature both display and command features can be created. The WML
“card” structure makes it possible to link from one menu screen to another, creating menus that are as many levels “deep” as desired or reduced to only those options needed by the printer operator.
Mirror
•
•
•
•
Mirror is a feature that gives you the ability to:
Centrally manage and monitor the deployment of your Zebra printers
Centrally configure and maintain your Zebra printers through remote updates
Remotely monitor printer updates – via the “Feedback” feature
There are several Set/Get/Do (SGD) commands that can initiate Mirror. For details see the
ZPL Manual.
•
Benefits
When using Mirror, updating the configuration and firmware on the printer is remotely managed from a centralized FTP server. Configurations can be uniformly deployed to individual printers or to groups of printers. Unique Configurations can also be targeted to printers as needed. Through the “Feedback” feature, Administrators can easily log and monitor configuration updates on a printer-by-printer basis. Typical uses of Mirror include:
• Configuring printers as they are first received.
• Performing scheduled maintenance updates, sending firmware, fonts, graphics and other objects to the printer as needed.
• Changing printer Configurations in order to move printers from one role to another.
12/30/2013 14588L-015
12
Summary of Firmware ChangesSGD Wireless Commands
V56.16.9Z
• Supported printers and print servers:
Printer
G-series
•
•
Print Servers
Internal, Integrated 10/100 wired
Internal Wireless and Wireless Plus
Print Servers connected to the parallel port, either externally or internally, are not supported for Mirror use.
See the ZPL Manual for full details on the Mirror feature.
Issues Corrrected
• The integrated internal wired and wireless print servers will now close the connection when the Host resets a connection that does not contain any data.
• Dynamic Media Calibration enhanced to use more data samples
• The EPL Q command value no longer overwrites the calibrated label length.
V56.16.9Z
Release Date: 21 May 2009
This firmware release includes features of the previous V56.16.7Z release. It is for use with the following printer models:
• GX420d
• GX420t
• GX430t
Note •
V56.16.8Z was not released.
Issues Corrected
• In line mode, the 12 digit UPC-A barcode will now use 11 digits to calculate the check digit.
• Darkness consistency across continuously printed labels in Thermal Transfer has been improved.
14588L-015 12/30/2013
Summary of Firmware ChangesSGD Wireless Commands
V56.16.7Z
13
V56.16.7Z
Release Date: 22 April 2009
This firmware release includes features of the previous V56.16.6Z release. It is for use with the following printer models:
• GX420d
• GX420t
• GX430t
Changes
• Peel and Cutter Modes enabled to support printers equipped with Peel or Cutter hardware.
• ZPL Black Line mode now operates as it did in legacy printers. The ^MN command has been enhanced to support an offset parameter when the printer is set to “Non-continuous media mark sensing” (^MNM). This parameter allows the user to set an offset position for the black mark. The default for this parameter is 0, the range for the parameter is
Details are as follows:
Format ^MNa,b
This table identifies the parameters for this format:
Parameters
a
= media being used b
= mark offset
Details
Accepted Values:
N
= continuous media
Y = non-continuous media web sensing*
W
= non-continuous media web sensing*
M
= non-continuous media mark sensing
A = auto-detects the type of media during calibration**
Default Value: a value must be entered or the command is ignored
Accepted Values:
-80 to +283 for the GX420d
-120 to +283 for the GX420t
-80 to +283 = the number of dot rows the black mark is offset from the perforation.
Note •
For 600 dpi printers, the step size doubles.
Default Value: 0
*.Provides the same result.
**.This parameter is supported only on G-series printers.
Comments This command is ignored on the HC100™ printer.
12/30/2013 14588L-015
14
Summary of Firmware ChangesSGD Wireless Commands
V56.16.6Z
Issues Corrected
• Entering and exiting EPL Line Mode now works correctly.
• Diagnostic mode now works correctly when accessed from EPL Line Mode, EPL Page
Mode, and ZPL.
V56.16.6Z
Release Date: 05 January 2009
This firmware release includes features of the previous V56.16.5Z release. It is for use with the following printer models:
• GX420d
• GX420t
• GX430t
Changes
• Support for ZBI 2.1 added (CSVLOAD, CSVSTORE, TXTLOAD, TXTSTORE). Refer to the
ZPL II
Programming Guide for complete details.
• Rectangular Datamatrix bar codes are now supported. A new “aspect ratio” parameter has been added to the ^BX command to support this new functionality. Refer to the ZPL II
Programming Guide for complete details
.
Issues Corrected
• The ZBI – VAL() function will now correctly convert a string value to a number.
• Code 128 Auto with F1 command in the data stream will now print.
• Formats using graphics and binary 02, 03 and 0F characters now print correctly.
• Intermittent image distortion issue when printing graphics no longer occurs.
• Use of the ZPL ^LH command will no longer effect the positioning of documents described using EPL .
• Use of the ZPL ^LT command will no longer effect the positioning of documents described using EPL
.
• Use of the ZPL ^CM command will no longer effect the ability to locate objects with EPL.
• The Bluetooth PIN code will no longer be requested for every print request.
• The printer can now process SDG commands expressed in UTF-16.
• The Front Panel will no longer intermittently display "1HEAD OPEN0" instead of "HEAD
OPEN".
• The EPL “R” command will now have the desired effect when used repeatedly.
• Internal 10/100 Print Server now responds to TCP packets when sent at a high rate.
14588L-015 12/30/2013
Summary of Firmware ChangesSGD Wireless Commands
V56.16.5Z
15
• The print server will remain on-line after a very high level of NetBIOS traffic.
• Printer retains default gateway after power cycle
• Printer web pages now load when using advanced wireless settings
V56.16.5Z
Release Date: 25 June 2008
This firmware release includes features of the previous V56.15.6Z release. It is for use with the following printer models:
• GX420d
• GX420t
• GX430t
Changes
ZBI 2.0
• V56.16.5Z and later firmware version are ZBI 2.0-Ready.
• ZBI 2.0 can be enabled by placing a ZBI 2.0 key on the printer via the ZBI Key Manager
& Downloader utility. Printers can be ordered from the factory with the ZBI 2.0 option enabled. Printers can be ZBI-Enabled in the field by purchasing and using a ZBI Key Kit.
Printers can be ZBI-Enabled in the field by purchasing a key at www.zebrasoftware.com.
• Printers which have been ZBI-Enabled will not display a “Z” at the end of the firmware version string. For example, a printer which has been ZBI-Enabled will display the firmware version as V56.16.5, while a printer which has not been ZBI-Enabled will display the firmware version as V56.16.5Z.
• The printer configuration label will display the ZBI status for the printer:
ZBI-Enabled
12/30/2013
• ZBI 2.0 is backwards compatible with previous versions of ZBI. Any code which was specifically written to handle a maximum string length of 255 characters will need to be reviewed to ensure it works with unlimited string lengths.
• Support for longer strings, the length of the string dependent on available memory.
• Support for NULL values in Strings and String operations
14588L-015
16
Summary of Firmware ChangesSGD Wireless Commands
V56.16.5Z
• SNMP & Set/Get/Do (SGD) Control of ZBI
• On-printer Debugging (via ZBI-Developer)
• ZBI 2.0 Program Encryption
• ZBI 2.0 programs can be made hidden and/or persistent
• Button presses on control panel can be registered as events in ZBI programs
• Support for longer strings, the length of the string dependent on available memory
• New ZBI 2.0 Commands added:
ACCEPT
ADDBREAK
CLIENTSOCKET
CLOSE ALL
DELBREAK
HANDLEEVENT
HEXTOINT
INTTOHEX$
READ
New ZBI 2.0 Commands
REGISTEREVENTS
SERVERSOCKET
SPLIT
SPLITCOUNT
SUB
TCPX
TRIGGEREVENT
UNREGISTEREVENTS
WRITE
• New ZBI 2.0 Events added:
ZBI Event ID ZBI Event
68
69
70
71
72
Autobaud
Factory Default
Networking Default
Networking Factory Default
Print Width
74
75
Calibrate
Scroll Key
• New ZBI 2.0 Key Events added:
Control Panel Key ZBI Event ID ZBI Name
Feed
Key
Select
Key
Scroll
Key
3
10
75
Feed Key
Select Key
Scroll Key
See the latest ZPL manual (available at www.zebra.com
) for details on new commands.
14588L-015 12/30/2013
Summary of Firmware ChangesSGD Wireless Commands
V56.16.5Z
17
Bluetooth / Wireless
• Support for Bluetooth (with LCD control panel) or 802.11b/g option (with LCD control panel). See
for supported Wireless Securities.
Table 1 •
Securities
Supported
Open
WEP 40-bit & 128-bit
LEAP
PEAP
EAP- FAST
EAP-TLS
EAP-TTLS
WPA PSK
WPA LEAP
WPA PEAP
Internal
Wireless
802.11b/g
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Securities
Supported
WPA EAP- FAST
WPA EAP-TLS
WPA EAP-TTLS
WPA2 PSK
WPA2 LEAP
WPA2 PEAP
WPA2 EAP- FAST
WPA2 EAP-TLS
WPA2 EAP-TTLS
KERBEROS
Internal
Wireless
802.11b/g
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Not Supported
Wireless Notes
The following items are issues Zebra has noted during testing with various wireless networking products:
• It is recommended to set WPA Handshaking to 1000.
• It is recommended to disable the Aironet Extensions.
• It is recommended to use Cisco Access Point firmware 12.3(8)JAE1 or later.
12/30/2013 14588L-015
18
Summary of Firmware ChangesSGD Wireless Commands
V56.15.6Z
V56.15.6Z
Release Date: 11 April 2008
This is the initial firmware release for the following printer models:
• GX420d
• GX420t
• GX430t
New Features
New implementation to support new printer models.
• Dual support for ZPL and EPL II.
• New SetGetDo commands.*
• Support for internal wired print server.
*See the current ZPL Guide for a complete list of the new commands.
For support, please visit www.zebra.com/support or refer to the contact options below:
Geographic Location
The Americas
Asia Pacific
Europe, Africa,
Middle East, India
Telephone Toll-free
+1-847-955-2299 +1-877-ASK-ZEBRA
+65-6858-0722 —
Please contact your supplier.
FAX
—
+65 6885 0838
14588L-015 12/30/2013
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project