Samsung | DVD-FP580W | User manual | Samsung DVD-FP580W User manual

DVD Player
DVD-FP580 / FP580W
DVD-F1080 / F1080W
www.samsung.com
AK68-01464N(02)
PRECAUTIONS
1. Setting up
- Refer to the identification label located on
the rear of your player for its proper operating voltage.
- Install your player in a cabinet with adequate ventilation holes. (7~10cm) Do not
block ventilation holes on any of the components for air circulation.
- Do not push the disc tray in by hand.
- Do not stack components.
- Be sure to turn all components off before
moving the player.
- Before connecting other components to this
player, be sure to turn them off.
- Be sure to remove the disc and turn off the
player after use, especially if you are not
going to use it for a long time.
- The mains plug is used as a disconnect
device and shall stay readily operable at
any time.
2. For your safety
- This product utilizes a laser. Use of controls
or adjustments or performance of procedures other than those specified herein may
result in hazardous radiation exposure.
- Do not open covers and do not repair yourself. Refer servicing to qualified personal.
3. Caution
- Your player is not intended for industrial use
but for domestic purposes. Use of this product is for personal use only.
- Apparatus shall not be exposed to dripping
or splashing and no objects filled with liquids, such as vases, shall be placed on the
apparatus.
- Exterior influences such as lightning and
static electricity can affect normal operation
of this player. If this occurs, turn the player
off and on again with the POWER button, or
disconnect and then reconnect the AC
power cord to the AC power outlet. The
player will operate normally.
- When condensation forms inside the player
due to sharp changes in temperature, the
2
player may not operate correctly. If this
occurs, leave the player at room temperature until the inside of the player becomes
dry and operational.
4. Disc
- Do not clean disc using record-cleaning
sprays, benzene, thinner, or other volatile
solvents that may cause damage to the disc
surface.
- Do not touch the disc’s signal surface. Hold
by the edges or by one edge and the hole
in the center.
- Wipe the dirt away gently; never wipe a
cloth back and forth over the disc.
5. Environmental info
- The battery used in this product contains
chemicals that are harmful to the environ
ment.
- So, dispose of batteries in the proper man
ner, according to federal, state, and local
regulations.
The product unit accompanying this user manual is
licensed under certain intellectual property rights of
certain third parties. This license is limited to private
non-commercial use by end-user consumers for
licensed contents. No rights are granted for
commercial use. The license does not cover any
product unit other than this product unit and the
license does not extend to any unlicensed product
unit or process conforming to ISO/OUR 11172-3 or
ISO/OUR 13818-3 used or sold in combination with
this product unit. The license only covers the use of
this product unit to encode and/or decode audio files
conforming to the ISO/OUR 11172-3 or ISO/OUR
13818-3. No rights are granted under this license for
product features or functions that do not conform to
the ISO/OUR 11172-3 or ISO/OUR 13818-3.
CAUTION: USE OF ANY CONTROLS,
ADJUSTMENTS, OR PROCEDURES OTHER
THAN SPECIFIED HEREIN MAY RESULT IN
HAZARDOUS RADIATION EXPOSURE.
Accessories
Remote Control
User’s Manual
A Battery for Remote
Control (CR2025)
Video/Audio
Cable
AC IN Cable
Install Batteries in the Remote control
1. Open the battery cover on the bottom side of the
remote control.
2. Insert a battery (CR2025).
Make sure that the
polarities (+ and -) are aligned correctly.
3. Replace the battery cover.
If remote control doesn’t operate
properly:
- Check the polarity + - of the battery (Dry-Cell)
- Check if the battery is drained.
- Check if remote control sensor is blocked by
obstacles.
- Check if there is any fluorescent lighting nearby.
TABLE OF
CONTENTS
Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Before you start . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Setup
General Features . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Disc Type and Characteristics . . . . . . . . . . . . . . . . 5
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Tour of the Remote Control . . . . . . . . . . . . . . . . . . 8
Connections
Choosing a Connection . . . . . . . . . . . . . . . . . . . . . 9
Basic Functions
Playing a Disc . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Using the Search and Skip Functions . . . . . . . . . 16
Using the Display Function . . . . . . . . . . . . . . . . . 16
Using the Disc and Title Menu . . . . . . . . . . . . . . 17
Using the Function Menu . . . . . . . . . . . . . . . . . . 17
Repeat Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Slow Play . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Advanced Functions
Adjusting the Aspect Ratio (EZ View) . . . . . . . . . 18
Selecting the Audio Language . . . . . . . . . . . . . . . 19
Selecting the Subtitle Language. . . . . . . . . . . . . . 19
Changing the Camera Angle . . . . . . . . . . . . . . . . 20
Using the Bookmark Function . . . . . . . . . . . . . . . 20
Using the Zoom Function . . . . . . . . . . . . . . . . . . . 21
Clips Menu for MP3/WMA/JPEG/MPEG4/
CD Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Folder Selection . . . . . . . . . . . . . . . . . . . . . . . . . . 21
MP3/WMA/CD Audio Playback. . . . . . . . . . . . . . . 22
MPEG4 Playback . . . . . . . . . . . . . . . . . . . . . . . . . 22
Picture CD Playback. . . . . . . . . . . . . . . . . . . . . . . 24
Changing Setup Menu
Using the Setup Menu . . . . . . . . . . . . . . . . . . . . . 25
Setting Up the Language Features . . . . . . . . . . . 25
Setting Up the Audio Options . . . . . . . . . . . . . . . . 26
Setting Up the Display Options . . . . . . . . . . . . . . 27
Setting Up the Parental Control . . . . . . . . . . . . . . 29
Setting Up the Anynet+(HDMI-CEC)
(DVD-F1080 only) . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Reference
Firmware Upgrade . . . . . . . . . . . . . . . . . . . . . . . . 31
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
3
English
BEFORE YOU
STAR T
SETUP
General Features
Excellent Sound
Dolby Digital, a technology developed by Dolby
Laboratories, provides crystal clear sound reproduction.
Screen
Both regular and widescreen(16:9) pictures can be
viewed.
Slow Motion
An important scene can be viewed in slow motion.
1080p Playback
This player upconverts regular DVDs for playback
on 1080p TVs (DVD-F1080 only).
Parental Control (DVD)
The parental control allows users to set the level
necessary to prohibit children from viewing harmful
movies such as those with violence, adult subject
matter, etc.
Various On-Screen Menu Functions
You can select various languages (Audio/Subtitle)
and screen angles while enjoying movies.
Progressive Scan
Progressive scanning creates an improved picture
with double the scan lines of a conventional interlaced picture.
EZ VIEW (DVD)
Easy View enables picture adjustment to match
your TV's screen size (16:9 or 4:3).
Digital Photo Viewer (JPEG)
You can view Digital Photos on your TV.
Repeat
You can repeat a song or movie simply by pressing
the REPEAT button.
MP3/WMA
This unit can play discs created from MP3/WMA
files.
MPEG4
This unit can play MPEG4 formats within an avi file.
HDMI (High Definition Multimedia
Interface)
HDMI reduces picture noise by allowing a pure
digital video/audio signal path from the player to
your TV (DVD-F1080 only) .
4
Note
- Discs which cannot be played with this
player.
• DVD-ROM
• DVD-RAM
• CD-ROM
• CDV
• CDI
• CVD
• CDGs play audio only, not graphics.
- Ability to play back may depend on recording
conditions.
• DVD-R, +R
• CD-RW
• DVD+RW, -RW (V mode)
- The unit may not play certain CD-R, CD-RW
and DVD-R due to the disc type or recording
conditions.
COPY PROTECTION
Many DVD discs are encoded with copy protection.
Because of this, you should only connect your DVD
player directly to your TV, not to a VCR. Connecting
to a VCR results in a distorted picture from copyprotected DVD discs.
This product incorporates copyright protection
technology that is protected by methods claims of
certain U.S. patents and other intellectual property
rights owned by Macrovision Corporation and other
rights owners. Use of this copyright protection technology must be auzthorized by Macrovision
Corporation, and is intended for home and other
limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
PROGRESSIVE SCAN OUTPUTS
DVD-FP580 (525p)/
DVD-F1080 (525p,720p,1080p)
“CONSUMERS SHOULD NOTE THAT NOT ALL
HIGH DEFINITION TELEVISION SETS ARE FULLY
COMPATIBLE WITH THIS PRODUCT AND MAY
CAUSE ARTIFACTS TO BE DISPLAYED IN THE
PICTURE, IN CASE OF 525, 720, 1080 PROGRESSIVE SCAN PICTURE PROBLEMS, IT IS
RECOMMENDED THAT THE USER SWITCH THE
CONNECTION TO THE ‘STANDARD DEFINITION’
OUTPUT. IF THERE ARE QUESTIONS
REGARDING YOUR TV SET COMPATIBILITY
WITH THIS MODEL 525p, 720p, 1080p DVD PLAYER, PLEASE CONTACT SAMSUNG'S CUSTOMER
SERVICE CENTER.”
Disc Type and Characteristics
This DVD player is capable of playing the following types of discs with the corresponding logos:
Recording Types
DVD
Audio
+
Video
AUDIO-CD
Disc Size
Max. Playing Time
12 Cm
Single-sided 240 min.
Double-sided 480 min.
- DVD contains excellent sound and
video due to Dolby Digital and MPEG2 system.
8 Cm
Single-sided 80 min.
Double-sided 160 min.
- Various screen and audio functions
can be easily selected through the onscreen menu.
12 Cm
74 min.
8 Cm
20 min.
Audio
Characteristics
- CD is recorded as a Digital Signal
with better audio quality, less distortion and less deterioration of audio
quality over time.
Disc Markings
Region Number
~
PAL
Play Region Number
PAL broadcast system in U.K, France,
Germany, etc.
Dolby Digital disc
STEREO
DIGITAL
SOUND
Stereo disc
Digital Audio disc
Both the DVD player and the discs are coded
by region. These regional codes must match in
order for the disc to play. If the codes do not
match, the disc will not play.
The Region Number for this player is
described on the bottom panel of the player.
DTS disc
MP3 disc
You must only insert one DVD disc at a time.
Inserting two or more discs will not allow to
play them back and it may cause damage to
the DVD player.
DivX Certification
DivX, DivX Certified,
and associated logos are trademarks of
DivXNetworks, Inc and are used under
license
5
English
Disc Types (Logos)
Description
Front Panel Controls
1.
2.
3.
4.
STANDBY/ON (
)
When STANDBY/ON is pressed on, the indicator goes
out and the player is turned on.
STANDBY Indicator
When the unit is first plugged in, the indicator lights.
DISC TRAY
Place the disc here.
5.
SKIP (
) / SEARCH
Use to reverse skip a scene or music..
6.
STOP (
)
Stops disc play.
7.
PLAY/PAUSE (
)
Begin or pause disc play.
OPEN/CLOSE (
)
Press to open and close the disc tray.
8.
SKIP (
) / SEARCH
Use to forward skip a scene or music.
3.
AUDIO OUT JACKS
- Connect to the Audio input jacks of your television or
audio/video receiver.
4.
VIDEO OUT JACK
- Use a video cable to connect to the Video input jack
on your television.
- The Video Output in Setup Menu must be set to
I-SCAN.
5.
AC IN JACK
- Use AC IN cable(Included) to connect this jack into
the power outlet.
Rear Panel (DVD-FP580)
1.
2.
DIGITAL AUDIO OUT JACKS
- Use coaxial digital cable to connect to a compatible
Dolby Digital receiver.
- Use coaxial digital cable to connect to an A/V
Amplifier that contains a Dolby Digital, MPEG2 or
DTS decoder.
COMPONENT VIDEO OUT JACKS
- Use these jacks if you have a TV with Component
Video in jacks. These jacks provide PR, PB and Y video.
- If P-SCAN Video Output is selected in Setup Menu,
progressive scan mode will work.
- If I-SCAN Video Output is selected in Setup Menu,
interlaced scan mode will work.
6
English
Rear Panel (DVD-F1080)
1.
DIGITAL AUDIO OUT JACKS
- Use coaxial digital cable to connect to a compatible
Dolby Digital receiver.
- Use coaxial digital cable to connect to an A/V
Amplifier that contains a Dolby Digital, MPEG2 or
DTS decoder.
2.
COMPONENT VIDEO OUT JACKS
- Use these jacks if you have a TV with Component
Video in jacks. These jacks provide PR, PB and Y video.
- If P-SCAN Video Output is selected in Setup Menu,
progressive scan mode will work.
- If I-SCAN Video Output is selected in Setup Menu,
interlaced scan mode will work.
3.
AUDIO OUT JACKS
- Connect to the Audio input jacks of your television or
audio/video receiver.
4.
VIDEO OUT JACK
- Use a video cable to connect to the Video input jack
on your television.
5.
AC IN JACK
- Use AC IN cable(Included) to connect this jack into
the power outlet.
6.
HDMI OUT JACK
- Use the HDMI cable to connect this jack to the HDMI
jack on your television for the best quality picture.
- If an HDMI cable is connected to an HDMI-compatible TV, HDMI will be output automatically within 10
seconds.
Note
- Consult your TV User’s Manual to find out if your TV supports Progressive Scan (P-SCAN).
If Progressive Scan is supported, follow the TV User’s Manual regarding Progressive Scan settings in
the TV’s menu system.
- The HDMI output of this unit can be connected to a DVI jack on a TV or other device using a conversion adapter. In this case, it is necessary to use a TV or display with an HDCP-compatible DVI input
(DVD-F1080 only).
- There may be no image output if the DVD player is connected to a TV or display that is not compatible
with the above format.
- Refer to the TV's instruction manual for detailed information regarding the HDMI terminal (DVD-F1080
only).
- See pages 27 ~ 28 to get more information on how to use the setup menu.
7
Tour of the Remote Control
1.
STANDBY/ON Button
Turns the power on or standby.
2.
1
2
3
4
5
6
7
8
9
12
13
14
15
16
17
18
3.
DISC MENU (NUMBER 4) Button
Brings up the Disc menu.
4.
ZOOM (NUMBER 7) Button
Enlarge DVD Picture.
5.
INFO Button
Displays the current disc mode.
6.
SEARCH Buttons (
)
/
Allow you to search forward/backward through a disc.
7.
STOP Button (
8.
SKIP Buttons (
19
10
NUMBER Buttons
9.
)
)
/
Use to skip the title, chapter or track.
MENU Button
Brings up the DVD player’s menu.
11
20
œ/ƒ
ƒ,¦
¦/‹
‹ Buttons
10. ENTER/œ
This button functions as a toggle switch.
11. EXIT Button
Exit the on-screen menu.
12. OPEN/CLOSE (
) Button
To open and close the disc tray.
13. AUDIO (NUMBER 5) Button
Use this button to access various audio functions on a disc.
14. REPEAT (NUMBER 6) Button
Allows you to repeat play a title, chapter, track or disc.
15. SUBTITLE (NUMBER 9) Button
16. VIDEO SEL. Button
Change Video output mode.
17. EZ VIEW (NUMBER 0) Button
The aspect ratio of a picture can easily be adjusted
according to the screen size of your TV (16:9 or 4:3).
18. PLAY/PAUSE Button (
)
Begin/Pause disc play.
19. RETURN Button
Returns to a previous menu.
20. CANCEL Button
Use to remove menus or status displays from the
screen.
8
CONNECTIONS
English
Choosing a Connection
The following shows examples of connections commonly used to connect the DVD player with a TV and
other components.
Before Connecting the DVD Player
- Always turn off the DVD player, TV, and other components before you connect or disconnect any cables.
- Refer to the user’s manual of the additional components you are connecting for more information on those
particular components.
Connecting to a TV (VIDEO CVBS)
1
Using video/audio cables, connect the VIDEO
(yellow)/AUDIO (red and white) OUT terminals on the rear
of the DVD player to the VIDEO (yellow)/AUDIO (red and
white) IN terminals of TV.
2
Turn on the DVD player and TV.
RED
WHITE
Audio
Cable
RED
WHITE
YELLOW
Video Cable
YELLOW
3
Press the input selector on your TV remote control until the
Video signal from the DVD player appears on the TV
screen.
Note
- Noise may be generated if the audio cable is too close to the power cable.
- If you want to connect to an Amplifier, please refer to the Amplifier connection page. (See pages 13 to 14)
- The number and position of terminals can vary depending on your TV set. Please refer to the user's manual of the TV.
- If there is one audio input terminal on the TV, connect it to the [AUDIO OUT][left] (white) terminal of the
DVD player.
- If you press the VIDEO SEL. button when DVD Player is in stop mode or no disc is inserted, the Video Output
mode changes in the following sequence: (I-SCAN ➝ P-SCAN).
9
Connection to a TV (Interlace)
- Connecting to your TV using Component video cables.
- You will enjoy high quality and accurate color reproduction images. Component video separates the picture element into black and white(Y), blue(PB), red(PR) signals to present clear and clean images. (Audio
signals are delivered through the audio output.)
1
Using component video cables (not included), connect the
COMPONENT VIDEO OUT terminal on the rear of the
DVD player to the COMPONENT IN terminal of TV.
2
RED
BLUE
GREEN
Using the audio cables, connect the AUDIO (red and
white) OUT terminals on the rear of the DVD player to the
AUDIO (red and white) IN terminals of TV. Turn on the
DVD player and TV.
RED
WHITE
3
Press the input selector on your TV remote control until the
Component signal from the DVD player appears on the TV
screen.
Audio Cable
RED
WHITE
RED
BLUE
GREEN
Component cable
(not included)
4
Set the Video Output to I-SCAN in the Display Setup
menu. (See pages 28)
You can use the VIDEO SEL. button to change the Video
Output mode. (See page 9)
Note
- If you want to connect to an Amplifier, please refer to the Amplifier connection page. (See pages 13 to 14)
- The component terminal of TV can be marked by “R-Y, B-Y, Y” or “Cr, Cb, Y” instead of “PR, PB, Y”
depending on the manufacturer. The number and position of terminals can vary depending on the TV set.
Please refer to the user's manual of the TV.
10
Connection to a TV (Progressive)
1
2
RED
BLUE
English
Using component video cables (not included), connect the
COMPONENT VIDEO OUT terminal on the rear of the
DVD player to the COMPONENT IN terminal of TV.
GREEN
Using the audio cables, connect the AUDIO (red and
white) OUT terminals on the rear of the DVD player to the
AUDIO (red and white) IN terminals of TV. Turn on the
DVD player and TV.
RED
3
Press the input selector on your TV remote control until the
Component signal from the DVD player appears on the TV
screen.
WHITE
Audio Cable
RED
WHITE
RED BLUE
GREEN
Component cable
(not included)
4
Set the Video Output to P-SCAN in the Display Setup
menu. (See pages 28)
You can use the VIDEO SEL. button to change the Video
Output mode. (See page 9)
To see the progressive video output,
-You
Consult
TVsupporting
User’s Manual
to find out
need ayour
TV set
the progressive
scanif your TV supports Progressive Scan. If Progressive
Scan isfunction.
supported,
follow
TV up
User’s
Manual regarding Progressive Scan settings in the TV’s
input
And you
havethe
to set
the TV
menu system.
- Depending on your TV, the connection method may differ from the illustration above.
Note
- What is "Progressive Scan"?
Progressive scan has twice as many scanning lines as the interlace output method has. Progressive
scanning method can provide better and clearer picture quality.
11
Connecting to a TV with DVI Jack (DVD-F1080 only)
1
Using the HDMI-DVI cable (not included), connect the
HDMI OUT terminal on the rear of the DVD player to the
DVI IN terminal of your TV.
2
Using the audio cables, connect the AUDIO (red and
white) OUT terminals on the rear of the DVD player to the
AUDIO (red and white) IN terminals of your TV.
Turn on the DVD player and TV.
RED
WHITE
Audio Cable
RED
WHITE
HDMI-DVI cable
(Not Included)
3
Press the input selector on your TV remote control until the
DVI signal from the DVD player appears on your TV
screen.
Connecting to a TV with HDMI Jack (DVD-F1080 only)
1
Using the HDMI-HDMI cable connect the HDMI OUT terminal on the rear of the DVD player to the HDMI IN terminal
of your TV.
2
Press the input selector on your TV remote control until the
HDMI signal from the DVD player appears on your TV
screen.
HDMI cable
(Not Included)
HDMI VIDEO Specifications
- Depending on your TV, certain HDMI output resolutions may not work.
- Please refer to the user's manual of your TV.
- If HDMI or HDMI-DVI cable is plugged into TV, the DVD player’s output is set to HDMI/DVI within 10
seconds.
- If you set the HDMI output resolution 720p,1080p or 1080i, HDMI output provides better picture
quality.
- If you connect an HDMI cable between Samsung TV and this DVD player, you can operate this DVD player
using your TV remote control. This is only available with Samsung TVs that support Anynet+(HDMI-CEC).
(See page 30).
- If your TV has an
logo, then it will
Supports the Anynet+ Function.
12
HDMI is an interface to enable the digital transmission
of video and audio data with just a single connector.
Using HDMI, the DVD player transmits a digital video
and audio signal and displays a vivid picture on a TV
having an HDMI input jack.
• HDMI connection description
HDMI connector - Both uncompressed video data and
digital audio data (LPCM or Bit Stream data).
- Though the player uses a HDMI cable, the player
outputs only a pure digital signal to the TV.
- If TV does not support HDCP (High-bandwidth
Digital content protection), snow noise appears on
the screen.
• Why does Samsung use HDMI?
Analog TVs require an analog video/audio signal.
However, when playing a DVD, the data transmitted
to a TV is digital. Therefore either a digital-to-analog
converter (in the DVD player) or an analog-to-digital
converter (in the TV) is required. During this conversion, the picture quality is degraded due to noise and
signal loss. DVI technology is superior because it
requires no D/A conversion and is a pure digital signal from the player to your TV.
• What is the HDCP?
HDCP (High-bandwidth Digital Content Protection) is
a system for protecting DVD content outputted via
DVI from being copied. It provides a secure digital
link between a video source (PC, DVD. etc) and a
display device (TV, projector . etc). Content is
encrypted at the source device to prevent unauthorized
Connection to an Audio System (2 Channel Amplifier)
1
Using the audio cables, connect the AUDIO (red and
white) OUT terminals on the rear of the DVD player to the
AUDIO (red and white) IN terminals of the Amplifier.
2
Using the video signal cable(s), connect the VIDEO or
COMPONENT OUT terminals on the rear of the DVD player to the VIDEO or COMPONENT IN terminal of your TV as
described on pages 9 to 12.
RED
3
WHITE
Audio Cable
Turn on the DVD player, TV, and Amplifier.
RED
WHITE
2-Channel stereo amp
4
Press the input select button of the Amplifier to select
external input in order to hear sound from the DVD player.
Note
- Please turn the volume down when you turn on the Amplifier. Sudden loud sound may cause
damage to the speakers and your ears.
- Please set the audio in the menu screen according to the Amplifier. (See pages 26 to 27)
- The position of terminals can vary depending on the Amplifier.
Please refer to the user's manual of the Amplifier.
13
English
• HDMI (High Definition Multimedia Interface)
Connection to an Audio System (Dolby digital, MPEG2 or DTS Amplifier)
1
If using a coaxial cable (not included), connect the DIGITAL AUDIO OUT (COAXIAL) terminal on the rear of the
DVD player to the DIGITAL AUDIO IN (COAXIAL) terminal of the Amplifier.
2
Using the video signal cable(s), connect the VIDEO,
COMPONENT or HDMI OUT (DVD-F1080 only) terminals
on the rear of the DVD player to the VIDEO, COMPONENT or DVI IN terminals of your TV as described on
pages 9 to 12.
Coaxial Cable
(not included)
3
Turn on the DVD player, TV, and Amplifier.
Dolby digital or
DTS amp
4
Press the input select button of the Amplifier to select
external input in order to hear sound from the DVD player.
Refer to your Amplifier's user manual to set the Amplifier's
audio input.
Note
- Please turn the volume down when you turn on the Amplifier. Sudden loud sound may cause
damage to the speakers and your ears.
- Please set the audio in the menu screen according to the Amplifier. (See pages 26 to 27)
- The position of terminals can vary depending on the Amplifier.
Please refer to the user's manual of the Amplifier.
14
BASIC FUNCTIONS
Before Play
- Turn on your TV and set it to the correct Video
Input by pressing TV/VIDEO button on the TV
remote control.
- If you connected an external Audio System, turn
on your Audio System and set it to the correct
Audio Input.
After plugging in the player, the first time you press the DVD
POWER button, this screen comes up: If you want to select
a language, press a NUMBER button. (This screen will only
appear when you plug in the player for the first time.)
If the language for the startup screen is not set, the settings
may change whenever you turn the power on or off.
Therefore, make sure that you select the language you want
to use.
Once you select a menu language, you can change it by
pressing the (
) button on the front panel of the unit for
more than 5 seconds with no disc in the unit. Then the
SELECT MENU LANGUAGE window appears again where
you can reset your preferred language.
Press
1
for English
Touche
2
pour Français
Drücken Sie
3
für Deutsch
Pulsar
4
para Español
Premere
5
per Italiano
Druk op
6
voor Nederlands
Playback
) button during play.
5. Removing Disc
Press the OPEN/CLOSE (
) button.
6. Pausing Play
Press the PLAY/PAUSE ( ) button on the
remote control during play.
- Screen stops, no sound.
To resume, press the PLAY/PAUSE ( )
button once again.
7. Slow Motion Play
Press the SEARCH ( / ) button to choose the play
speed between 1/8, 1/4 and 1/2 of normal during PAUSE
mode.
- No sound is heard during slow mode.
- Press the PLAY/PAUSE ( ) button to resume
normal play.
Note
- If the player is left in the stop mode for more
than one minute without any user interaction, a
screen saver will be activated. Press the
PLAY/PAUSE ( ) button to resume normal play.
- If the player is left in the stop mode for more than
about 30 minutes, the power will automatically
shut off.(Automatic Power-Off Function)
- If the player is left for about 5 minutes in pause
mode, it will stop.
- This (
) icon indicates an invalid button press.
1. Press the OPEN/CLOSE ( ) button. The STANDBY
indicator light goes out and the tray opens.
2. Place a disc gently into the tray with the disc’s label facing
up.
3. Press the PLAY/PAUSE ( ) button or OPEN/ CLOSE
( ) button to close the disc tray.
- When you stop disc play, the player remembers
where you stopped, so when you press
PLAY/PAUSE ( ) button again, it will pick up where
you left off.
15
English
4. Stopping Play
Press the STOP (
Playing a Disc
Using the Search and Skip
Functions
During play, you can search quickly through a chapter or
track, and use the skip function to jump to the next selection.
Searching through a Chapter or
Track
During play, press the SEARCH (
or
remote control for more than 1 second.
DVD
2X, 4X, 64X, 128X
CD
2X, 4X, 8X
Using the Display Function
When Playing a DVD/MPEG4
1. During play, press the INFO button on the remote control.
- You can select Info in the function menu by pressing
the MENU button.
2. Press the œ/ƒbuttons to select the desired item.
3. Press the ¦/‹ buttons to make the desired setup and then
press the ENTER button.
- You may use the number buttons of the remote control
to directly access a title, chapter or to start the play
back from a desired time.
) button on the
4. To make the screen disappear, press the INFO button
again.
Note
- The speed marked in this function may be
different from the actual playback speed.
- No sound is hearing during search mode
(Except CD).
Note
Title
Skipping Tracks
During play, press the SKIP (
or
) button.
- When playing a DVD, if you press the SKIP (
Chapter
Most DVD discs are recorded in chapters so
that you can quickly find a specific passage.
Time
Allows playback of the film from a desired
time. You must enter the starting time as a
reference.The time search function does not
operate on some disc.
) button, it
moves to the next chapter. If you press the SKIP (
)
button, it moves to the beginning of the chapter. One more
press makes it move to the beginning of the previous
chapter.
- When playing a CD in Menu Off mode, if you press the
SKIP (
) button, it moves to the next track. If you press
the SKIP (
Audio
) button, it moves to the beginning of the
track. One more press makes it move to the beginning of
the previous track.
16
To access the desired title when there is
more than one in the disc. For example, if
there is more than one movie on a DVD,
each movie will be identified.
Subtitle
Refers to the language of the film soundtrack.
In the example, the soundtrack is played in
English 5.1CH. A DVD disc can have up to
eight different soundtracks.
Refers to the subtitle languages available in
the disc. You will be able to choose the
subtitle languages or, if you prefer, turn them
off from the screen. A DVD disc can have up
to 32 different subtitles.
Using the Disc and Title
Menu
Using the Function Menu
Using the Function Menu (DVD)
Using the Disc Menu
2. Press the œ/ƒ buttons to select Disc Menu, then press the
‹ or ENTER button.
Press ENTER key
for Disc Menu
Enter
Return
Using the Title Menu
1. During the playback of a DVD disc, press the MENU button
on the remote control.
2. Press the œ/ƒ buttons to select Title Menu, then press the
‹ or ENTER button.
Enter
Return
Menu
3. Press the œ/ƒ buttons to select one of the six functions.
Then press the ‹ or ENTER button to access the function.
You can also directly select these functions using their
respective buttons on the remote control.
- INFO
- ZOOM
- EZ VIEW
- REPEAT
Repeat Play
Repeat the current track, chapter, title, a chosen
section (A-B), or all of the disc.
When playing a DVD
Press ENTER key
for Title Menu
Return
Info
Zoom
Bookmark
Repeat
EZ View
Angle
Menu
Note
- Depending on a disc, the Disc Menu may not
work.
- You can also use the Disc Menu, using the
DISC MENU button on the remote control.
Enter
2. Press the œ/ƒ buttons to select Function, then press the
‹ or ENTER button.
- Info (See pages 16)
- Zoom (See page 21)
- Bookmark (See pages 20 to 21)
- Repeat (See pages 17 to 18)
- EZ View (See pages 18 to 19)
- Angle (See pages 20)
1. Press the REPEAT button on the remote control.
Repeat screen appears.
Menu
Note
- Depending on a disc, the Title Menu may not
work.
- Title Menu will only be displayed if there are at
least two titles in the disc.
2. Press the ¦/‹ buttons to select Chapter, Title or A-B,
then press the ENTER button.
- DVD repeats play by chapter or title.
- Chapter ( ): repeats the chapter that is playing.
- Title ( ): repeats the title that is playing.
- A-B: repeats a segment of the disc that you select.
T
DVD
Off
01
T
01 A - B
ENTER REPEAT
17
English
1. Press the MENU button during playback.
1. During the playback of a DVD disc, press the MENU button
on the remote control.
I
Using the A-B Repeat function
1. Press the REPEAT button on the remote control.
2. Press the ¦/‹ buttons to select A-B button.
3. Press the ENTER button at the point where you
want repeat play to start (A). B is automatically highlighted.
4. Press the ENTER button at the point where you
want the repeat play to stop (B).
- To return to normal play, press the CANCEL button.
3. To return to normal play, press REPEAT button again, then
press the ¦/‹ buttons to select Off and press ENTER
button.
DVD
Off
01
T
01 A - B
ENTER REPEAT
Note
- A-B REPEAT allows you to set point (B) until at
least 5 seconds of play back time has elapsed
after point (A) has been set.
- Depending on a disc, the Repeat function may
not work.
ADVANCED
FUNCTIONS
Adjusting the Aspect Ratio
(EZ View)
To play back using aspect ratio
(DVD)
Press the EZ VIEW button.
- The screen size changes when the button is pressed
repeatedly.
- The screen zoom mode operates differently depending on the
screen setting in the Display Setup menu.
- To ensure correct operation of the EZ VIEW button, you
should set the correct aspect ratio in the Display Setup
menu. (See pages 27 to 28).
WIDE SCREEN
EZ VIEW
Slow Play
This feature allows you slowly to repeat scenes containing sports, dancing, musical instruments being
played etc., so you can study them more closely.
When playing a DVD
1. During play, press the PLAY/PAUSE (
) button.
2. Press the SEARCH (
) button to choose the play
/
speed between 1/8, 1/4 and 1/2 of normal during PAUSE
mode.
If you are using a 16:9 TV
For 16:9 aspect ratio discs
- WIDE SCREEN
Displays the content of the DVD title in 16:9 aspect ratio.
- SCREEN FIT
The top and bottom portions of the screen are cut off.
When playing a 2.35:1 aspect ratio disc, the black bars at
the top and bottom of the screen will disappear. The picture
will look vertically stretched. (Depending on a type of disc,
the black bars may not disappear completely.)
- ZOOM FIT
The top, bottom, left and right of the screen are cut off and
the central portion of the screen is enlarge
For 4:3 aspect ratio discs
- Normal Wide
Displays the content of the DVD title in 16:9 aspect ratio.
The picture will look horizontally stretched.
- SCREEN FIT
The top and bottom portions of the screen are cut off and
the full screen appears.
The picture will look vertically stretched.
- ZOOM FIT
The top, bottom, left and right portions of the screen are
cut off and the central portion of the screen is enlarged.
- Vertical Fit
When a 4:3 DVD is viewed on a 16:9 TV, black bars will
appear at the left and right of the screen in order to prevent
the picture from looking horizontally stretched.
18
Y
e
U
(
1
2
For 16:9 aspect ratio discs
- 4:3 Letter Box
Displays the content of the DVD title in 16:9 aspect ratio. The
black bars will appear at the top and bottom of the screen.
- 4:3 Pan Scan
The left and right portions of the screen are cut off and the
central portion of the 16:9 screen is displayed.
- SCREEN FIT
The top and bottom portions of the screen are cut off and a
full screen appears. The picture will look vertically stretched.
- ZOOM FIT
The top, bottom, left and right of the screen are cut off and
the central portion of the screen is enlarged.
For 4:3 aspect ratio discs
- Normal Screen
Displays the content of the DVD title in 4:3 aspect ratio.
- SCREEN FIT
The top and bottom portions of the screen are cut off and the
full screen appears. The picture will look vertically stretched.
- ZOOM FIT
The top, bottom, left and right portions of the screen are cut
off and the central portion of the screen is enlarged.
Note
- This function depends on audio languages are
encoded on the disc and may not work.
- A DVD disc can contain up to 8 audio languages.
- To have the same audio language come up
whenever you play a DVD;
Refer to “Using the Audio Language” on page 26.
Selecting the Subtitle
Language
You can select a desired subtitle quickly and
easily with the SUBTITLE button.
Using the SUBTITLE button
(DVD/MPEG4)
1. Press the SUBTITLE button. The subtitle languages are
represented by abbreviations.
The subtitle changes when DVD
the button is pressed
Off
repeatedly.
SUBTITLE
Note
This function may behave differently depending on
the type of disc.
MPEG4
External subtitle option will
appear, depends the DivX
Disc.
Selecting the Audio
Language
Subtitle Selection
External Subtitle Off
readme.TXT
Non-standard fonts are not supported
You can select a desired audio language quickly and
easily with the AUDIO button.
Using the AUDIO button
(DVD/MPEG4)
1. Press the AUDIO button. The Audio changes when the
button is pressed repeatedly.
The audio languages are DVD
represented by
ENG DOLBY DIGITAL 5.1CH
abbreviations.
AUDIO
Press AUDIO button at
remote control repeatedly
to select the desired
Audio on MPEG4 then
press the ENTER .
MPEG4
PCM 1/2
AUDIO
2. To remove the AUDIO icon, press the CANCEL or RETURN
button.
Enter
Press SUBTITLE button
at remocon repeatedly to
select the desired subtitle language on a
MPEG4 then press the
ENTER .
Return
Menu
MPEG4
Off
SUBTITLE
2. To remove the SUBTITLE icon, press the CANCEL or
RETURN button.
Note
- You have to change the desired subtitle in the
Disc Menu, according to discs. Press the DISC
MENU button.
- This function depends on what subtitles are
encoded on the disc and may not work on all DVDs.
- A DVD disc can contain up to 32 subtitle
languages.
- To have the same subtitle language come up
whenever you play a DVD; Refer to “Using the
Subtitle Language” on page 26.
19
English
If you are using a 4:3 TV
Changing the Camera
Angle
Using the Bookmark
Function
When a DVD contains multiple angles of a particular
scene, you can use the ANGLE function.
Using the ANGLE function (DVD)
If the disc contains multiple angles, the ANGLE
appears on the screen.
This feature lets you bookmark sections of a DVD
so you can quickly find them at a later time.
1. During play or pause mode, press the MENU button on the
remote control.
2. Press the œ/ƒ buttons to select Function, then press the
‹ or ENTER button.
3. Press the œ/ƒ buttons to select Angle, then press the
‹ or ENTER button.
1. During play, press the MENU button on the remote control.
2. Press the œ/ƒ buttons to select Function, then press the
‹ or ENTER button.
Using the Bookmark Function
(DVD)
Info
Zoom
Bookmark
Repeat
Info
EZ View
Zoom
Angle
Bookmark
Enter
Repeat
Return
Menu
EZ View
Angle
Enter
Return
Menu
4. Press the ¦/‹ buttons on the remote control to select the
desired angle.
3. Press the œ/ƒ buttons to select Bookmark, then press the
‹ or ENTER button.
- - -
4/6
Note
- If the disc has only one angle, this feature won’t
work. Currently, very few discs have this feature.
- Depending on the disc, these functions may not
work.
4. When you reach the scene you want to mark, press the
ENTER button. Up to three scenes may be marked at a time.
1 - -
CANCEL
Note
- Depending on a disc, the Bookmark
function may not work.
Recalling a Marked Scene
1~3. The first 1~3 steps are the same as those for “Using the
Bookmark Function” on page 20.
4. Press the ¦/‹ buttons to select a marked scene.
1 2 3
5. Press the PLAY/PAUSE (
scene.
CANCEL
) button to skip to the marked
Clearing a Bookmark
1~3. The first 1~3 steps are the same as those for “Using the
Bookmark Function” on page 20.
4. Press the ¦/‹ buttons to select the bookmark number you
want to delete.
20
5. Press the CANCEL button to delete a bookmark number.
-
: Current Playback Mode : There are four
modes. They can be selected in order by
1 2 3
pressing the REPEAT button.
CANCEL
- Off: Normal Playback
- Track: Repeats the current track.
Using the Zoom Function
- Folder: Repeats the current folder
English
- Random: Files in the disc will be played in
Using the Zoom Function (DVD)
random order.
1. During play or pause mode, press the MENU button on the
remote control.
2. Press the œ/ƒ buttons to select Function, then press the
‹ or ENTER button.
3. Press the œ/ƒ buttons to select Zoom, then press the
‹ or ENTER button.
4. Press the œ/ƒ or ¦/‹ buttons to select the part of the
screen you want to zoom in on. Press the ENTER button.
- During DVD play, press ENTER to zoom in
2X/4X/2X/Normal in order.
-
: MP3 file icon.
-
: CD Audio file icon.
-
: WMA file icon.
-
: Folder icon.
-
: JPEG file icon
-
: Current Folder icon.
-
: AVI file icon.
Note
- When playing MP3, WMA or JPEG, the Picture
Quality and the HDMI Resolution cannot be set.
(DVD-F1080 only).
- When playing MPEG4 file, the VIDEO SEL. only
work in stop mode.
Info
Zoom
Bookmark
Repeat
EZ View
Angle
Enter
Return
Menu
Folder Selection
The folder can be selected both in Stop or Play mode.
CANCEL
- To select the Parent Folder
Press the RETURN button to go to parent folder, or press the
œ/ƒ
ƒ buttons to select “..” and press ENTER to go to the
parent folder.
Clips Menu for MP3/WMA/
JPEG/ MPEG4/CD Audio
CANCEL
CD Audio or discs with MP3/WMA/JPEG contain
individual songs and/or pictures that can be organized into folders as shown below. They are similar
to how you use your computer to put files into different folders.
Open the disc tray.
Place the disc on the tray.
Close the tray.
The tray closes and this
screen displays.
Stop
Off
T
- To select the Peer Folder
ƒ buttons to select the desired folder, then
Press the œ/ƒ
press ENTER.
- To select the Sub-Folder
ƒ buttons to select the desired folder,
Press the œ/ƒ
then press ENTER.
R oot
W MA
JPEG
P arent Fol der
MP 3
00:00:00
MU S IC
C urrent Fol der
WMA
JPEG
1s t
MP3
S ub-Fol ders
MPEG4
2nd
S ON G FILE 1
Enter
Return
Menu
P eer Fol ders
S ON G FILE 2
-
: Name of currently playing file.
S ON G FILE 3
MP E G4 FILE S
-
: Current Playback Time.
21
MP3/WMA/CD Audio
Playback
1. Open the disc tray. Place the disc on the tray. Close the tray.
- Only one kind of file is played back when a disc or a
folder contains both MP3 and WMA files.
ƒ buttons to select a song file.
2. Press the œ/ƒ
Press ENTER to begin playback of the song file.
Play
Off
B e c a u s e Yo u
T
00:00:23
...
B e c a u s e Yo u
Cactus
Sad Dayu
Wonderful
Enter
Return
REPEAT
Repeat
Repeat/Random playback
Press the REPEAT button to change the playback mode. There
are four modes, such as Off, Track, Folder and Random.
- Off: Normal Playback
- Track: Repeats the current song file.
- Folder: Repeats the song files which have the same
extension in the current folder.
- Random: Song files which have the same extension will be
played in random order.
To resume normal play, press the CANCEL button.
CD-R MP3/WMA file
When you record MP3 or WMA files on CD-R, please refer
to the following.
- Your MP3 or WMA files should be ISO 9660 or JOLIET
format.
ISO 9660 format and Joliet MP3 or WMA files are
compatible with Microsoft's DOS and Windows, and with
Apple's Mac. This format is the most widely used.
- When naming your MP3 or WMA files, do not exceed 8
characters, and enter “.mp3, .wma” as the file extension.
General name format : Title.mp3. or Title.wma. When
composing your title, make sure that you use 8 characters or
less, have no spaces in the name, and avoid the use of
special characters including: (.,/,\,=,+).
- Use a decompression transfer rate of at least 128 Kbps
when recording MP3 files.
Sound quality with MP3 files basically depends on the rate of
compression/decompression you choose. Getting CD audio
sound requires an analog/digital sampling rate, that is
conversion to MP3 format, of at least 128 Kbps and up to 160
Kbps. However, choosing higher rates, like 192 Kbps or more,
only rarely give better sound quality. Conversely, files with
decompression rates below 128 Kbps will not be played
properly.
22
- Use a decompression transfer rate of at least 64Kbps
when recording WMA files.
Sound quality with WMA files basically depends on the rate of
compression/decompression you choose.
Getting CD audio sound requires an analog/digital sampling
rate, that is conversion to WMA format, of at least 64Kbps
and up to 192Kbps. Conversely, files with decompression
rates below 64Kbps or over 192Kbps will not be played
properly.
- Do not try recording copyright protected MP3 files.
Certain "secured" files are encrypted and code protected to
prevent illegal copying. These files are of the following types:
TM
Windows Media (registered trade mark of Microsoft Inc) and
TM
SDMI (registered trade mark of The SDMI Foundation). You
cannot copy such files.
- Important:
The above recommendations cannot be taken as a
guarantee that the DVD player will play MP3 recordings, or as
an assurance of sound quality. You should note that certain
technologies and methods for MP3 file recording on CD-Rs
prevent optimal playback of these files on your DVD player
(degraded sound quality and in some cases, inability of the
player to read the files).
- This unit can play a maximum of 500 files and 500 folders
per disc.
MPEG4 Playback
MPEG4 Play Function
AVI files are used to contain the audio and video data. Only
AVI format files with the “.avi” extensions can be played.
1. Open the disc tray. Place the disc on the tray.
Close the tray.
ƒ or ¦/‹
‹ buttons to select an avi file
2. Press the œ/ƒ
(DivX/XiviD) and then press ENTER button.
Stop
Off
/MPEG4
T
00:00:00
...
a01_divx51b-8
a02_divx505b-8
a03_divx502sp-8
a04_divx412-8
Enter
Return
Menu
Repeat playback
Press the REPEAT button to change playback mode. There are
3 modes, such as Off, Folder and Title.
- Folder : repeats the AVI files which have the same extension
in the current folder.
- Title : repeats the title that is playing.
MPEG4 Function Description
Description
Reference page
During play, press the
or
button, it moves forward
or backward 5 minutes.
During play, press the SEARCH
(
or
) button and press
Search
again to search at a faster
(
or
) speed. Allows you to search
at a faster speed in an AVI
file. (2X, 4X, 8X)
Allows you to search at a
Slow Motion slower speed in an AVI file.
Play
(1/8X, 1/4X, 1/2X)
(
Skip
or
)
ZOOM
-
Authorization Error
This player is not authorized
to play this video
-
OK
Enter
Return
P 15
P 21
2X/4X/2X/Normal in order
Possible warning messages that may appear when trying to
play DivX/AVI files are :
1. No Authorization
- File with bad registration code.
English
Function
- These functions may not work depending on MPEG4 file.
CD-R AVI file
2. Unsupported Codec
- Files with certain Codec Types, Versions
(ex. MP4, AFS and other proprietary codecs) are not
suppoerted by this player.
Stop
Off
S w e e t Vo l 3
This unit can play the following video compression formats
within the AVI file format:
- DivX 3.11 contents
- DivX 4 contents (Based on MPEG-4 Simple Profile)
- DivX 5 contents (MPEG-4 simple profile plus additional
features such as bi-directional frames. Qpel and GMC are
also supported.)
- XviD MPEG-4 compliant Contents.
DVD-RW & DVD+R
T
...
B e c a u s e Yo u
C a c t u sFile
you attempt to play
has un supported codec.
Sad Dayu
Wo n d e r f u l
S w e e t Vo l 3
Enter
Menu
Return
3. Unsupported Resolution
- Files containing resolutions higher than the player’s
specification are not supported.
Stop
Off
/a01_divx51b-8
Format that support for DivX file :
- Basic DivX format DivX3.11 / 4.12/ 5.x
- Xvid (MPEG-4 compliant video codec) and DivX Pro
- File format : *.avi, *.div, *.divx.
00:00:20
T
00:00:00
...
a01_divx51b-8
File you attempt to play
has unsupported resolution.
a02_divx505b-8
a03_divx502sp-8
a04_divx412-8
Enter
Menu
Return
This unit supports all resolutions up to maximum below.
DivX3.11 & DivX4 & XviD
DivX5
Bitrate may fluctuate:
Device may skip decoding
the high bitrate portions
and begin decoding again
when Bitrate returns to
normal.
720 x 480 @30fps
720 x 576 @25fps
: Maximum bitrate : 4Mbps
Note
• The resolution that can be supported by DVDFP580/DVD-F1080 model up to 720 x 480 @30
frames/ 720 x 576 @25 frames
• This unit supports CD-R/RW written in MPEG4 in
accordance with the “ISO9660 format”.
23
Picture CD Playback
MP3-JPEG Playback
You can play JPEG using music as a backgound.
1. Select the desired folder.
ƒ buttons to select a Picture file in the clips
2. Press the œ/ƒ
menu and then press the ENTER button.
3. Press the INFO button on the remote control to select the
menu you want to view and then press the ENTER button.
ENTER RETURN
ƒ buttons to select an MP3 file in the clips
1. Press the œ/ƒ
menu and then press the ENTER button.
ƒ buttons to select a JPEG file in the
2. Press the œ/ƒ
clips menu and then press the ENTER button.
- Music will play from the beginning
3. Press Stop button when you want to stop the
playback.
Note
MP3 and JPEG files have to be on the same disc.
Note
- Press the STOP button to return to the clips menu.
- When playing a Kodak Picture CD, the unit
displays the Photo directly, not the clips menu.
Rotation
: Each time the ENTER button is pressed, the
picture rotates 90 degrees clockwise.
Zoom
ƒ buttons to select the part of the
: Press the œ/ƒ
screen you want to zoom in on.
Press the ENTER button. Each time the ENTER button is pressed, the picture is enlarged up to 2X.
Slide Show
•
: The unit enters slide show mode.
• Before beginning the Slide Show, the picture interval must
be set.
•
: When this icon is selected and ENTER is
pressed, the pictures change automatically
with about a 6 second interval.
•
: The pictures change automatically with
about a 12 second interval.
•
: The pictures change automatically with
about a 18 second interval.
TIMER:
ENTER RETURN
Note
- Depending on a file size, the amount of time
between each picture may be different from the
manual.
24
CD-R JPEG Disc
- Only files with the “.jpg” and “.JPG” extensions can be played.
- If the disc is not closed, it will take longer to start playing and
not all of the recorded files may be played.
- Only CD-R discs with JPEG files in ISO 9660 or Joliet format
can be played.
- The name of the JPEG file may not be longer than 8
characters and should contain no blank spaces or special
characters (. / = +).
- Only a consecutively written multi-session disc can be played.
If there is a blank segment in the multi-session disc, the disc
can be played only up to the blank segment.
- A maximum of 3000 images can be stored on a single CD.
- Kodak Picture CDs are recommended.
- When playing a Kodak Picture CD, only the JPEG files in the
pictures folder can be played.
- Kodak Picture CD: The JPEG files in the pictures folder can
be played automatically.
- Konica Picture CD: If you want to see the Picture, select the
JPEG files in the clips menu.
- Fuji Picture CD: If you want to see the Picture, select the
JPEG files in the clips menu.
- QSS Picture CD: The unit may not play QSS Picture CD.
- If the number of files in 1 Disc is over 500, only 500 JPEG
files can be played.
- If the number of folders in 1 Disc is over 500, only JPEG
files in 500 folders can be played
Setting Up the Language
Features
CHANGING SETUP
MENU
If you set the player menu, disc menu, audio and subtitle
language in advance, they will come up automatically every
time you watch a movie.
Using the Setup Menu
1. With the unit in Stop mode, press the MENU button on the
ƒ buttons to select Setup, then
remote control. Use the œ/ƒ
press the ‹ or ENTER button.
Language Setup
Audio Setup
‹
‹
Display Setup
‹
Parental Setup :
‹
DivX(R) Registration
‹
Enter
Return
Menu
1. With the unit in Stop mode, press the MENU button.
ƒ buttons to select Setup, then press the ‹
2. Press the œ/ƒ
or ENTER button.
ƒ buttons to select Language Setup, then
3. Press the œ/ƒ
press the ‹ or ENTER button.
ƒ buttons to select Player Menu, then press
4. Press the œ/ƒ
the ‹ or ENTER button.
ƒ buttons to select the desired language,
5. Press the œ/ƒ
then press the ‹ or ENTER button.
- The language is selected and the screen
returns to Language Setup menu.
- To make the setup menu disappear, press the MENU
button.
DVD-FP580 Setup Menu
LANGUAGE SETUP
Player Menu
Menu
Player
Language Setup
‹
Disc Menu
Audio Setup
‹
Audio
Display Setup
‹
Subtitle
Parental Setup :
‹
DivX Subtitle
DivX(R) Registration
‹
Enter
: English
√ English
Français
Deutsch
Español
Italiano
Nederlands
Return
Menu
Anynet+(HDMI-CEC):On
Enter
Return
Menu
Using the Disc Menu Language
DVD-F1080 Setup Menu
❶ Language Setup: Setup of the Language.
❷ Audio Setup : Setup of the Audio Options.
❸ Display Setup : Setup of the Display Options. Use to
select which type of screen you want to
watch and several display options.
❹ Parental Setup : Setup of the Parental Level. Allows
users to set the level necessary to
prevent children from viewing unsuitable
movies such as those with violence,
adult subject matter, etc.
❺ Divx(R) Registration : Please use the Registration code
to register this player with the
DivX(R) Video On Demand
format. To learn more go to
www.divx.com/vod.
❻ Anynet+(HDMI-CEC): Setup of the Anynet+(HDMI-CEC)
Options (DVD-F1080 only).
ƒ buttons to access the different features.
2. Press the œ/ƒ
Press the ‹ or ENTER button to access the sub features.
3. To make the setup screen disappear after setting up, press
the MENU button again.
This function changes the text language only on the disc
menu screens.
1. With the unit in Stop mode, press the MENU button.
ƒ buttons to select Setup, then press the ‹
2. Press the œ/ƒ
or ENTER button.
ƒ buttons to select Language Setup, then
3. Press the œ/ƒ
press the ‹ or ENTER button.
ƒ buttons to select Disc Menu, then press
4. Press the œ/ƒ
the ‹ or ENTER button.
ƒ buttons to select the desired language,
5. Press the œ/ƒ
then press the ‹ or ENTER button.
- If the selected language is not recorded on the disc,
the original pre-recorded language is selected.
- The language is selected and the screen returns to
Language Setup menu.
- To make the setup menu disappear, press the MENU
button.
LANGUAGE SETUP
Player Menu
Disc Menu
Audio
Note
Depending on the disc, some Setup Menu
selections may not work.
Subtitle
DivX Subtitle
Enter
√ English
Français
Deutsch
Español
Italiano
Nederlands
Return
Menu
25
English
Using the Player Menu Language
The Setup menu lets you customize your DVD player by
allowing you to select various language preferences, set up
a parental level, even adjust the player to the type of
television screen you have.
Using the Audio Language
Using the DivX Subtitle Language
1. With the unit in Stop mode, press the MENU button.
ƒ buttons to select Setup, then press the ‹
2. Press the œ/ƒ
or ENTER button.
ƒ buttons to select Language Setup, then
3. Press the œ/ƒ
press the ‹ or ENTER button.
ƒ buttons to select Audio, then press the ‹
4. Press the œ/ƒ
or ENTER button.
ƒ buttons to select the desired language,
5. Press the œ/ƒ
then press the ‹ or ENTER button.
- Select “Original” if you want the default soundtrack
language to be the original language the disc is
recorded in.
- If the selected language is not recorded on the disc, the
original pre-recorded language is selected.
- The language is selected and the screen returns to
Language Setup menu.
- To make the setup menu disappear, press the
MENU button.
1. With the unit in Stop mode, press the MENU button.
ƒ buttons to select Setup, then press the ‹
2. Press the œ/ƒ
or ENTER button.
ƒ buttons to select Language Setup, then
3. Press the œ/ƒ
press the ‹ or ENTER button.
ƒ buttons to select DivX Subtitle, then press
4. Press the œ/ƒ
the ‹ or ENTER button.
ƒ buttons to select the desired language,
5. Press the œ/ƒ
then press the ‹ or ENTER button.
- The language is selected and the screen returns to
Language Setup menu.
- To make the setup menu disappear, press the
MENU button.
LANGUAGE SETUP
Player Menu
: English
Disc Menu
: English
Audio
Subtitle
DivX Subtitle
√ Unicode
Western
Turkish
Central
Cyrillic
Greek
LANGUAGE SETUP
Enter
Player Menu
Original
√ English
Français
Audio
Deutsch
Subtitle
Español
DivX Subtitle
Italiano
Disc Menu
Enter
Return
Menu
Using the Subtitle Language
1. With the unit in Stop mode, press the MENU button.
ƒ buttons to select Setup, then press the ‹
2. Press the œ/ƒ
or ENTER button.
ƒ buttons to select Language Setup, then
3. Press the œ/ƒ
press the ‹ or ENTER button.
ƒ buttons to select Subtitle, then press the
4. Press the œ/ƒ
‹ or ENTER button.
ƒ buttons to select the desired language,
5. Press the œ/ƒ
then press the ‹ or ENTER button.
- Select “Automatic” if you want the subtitle language to
be the same as the language selected as the audio
language.
- Some discs may not contain the language you select as
your initial language; in that case the disc will use its
original language setting.
- The language is selected and the screen returns to
setup menu.
- To make the setup menu disappear, press the MENU
button.
LANGUAGE SETUP
Player Menu
Disc Menu
Audio
Subtitle
DivX Subtitle
Enter
26
√ Automatic
English
Français
Deutsch
Español
Italiano
Return
Menu
Return
Menu
Setting Up the Audio
Options
Audio Options allows you to setup the audio device
and sound status settings depending on the audio
system in use.
1. With the unit in Stop mode, press the MENU button.
ƒ buttons to select Setup, then press the ‹
2. Press the œ/ƒ
or ENTER button.
ƒ buttons to select Audio Setup, then press
3. Press the œ/ƒ
the ‹ or ENTER button.
ƒ buttons to select the desired item, then
4. Press the œ/ƒ
press the ‹ or ENTER button.
Language Setup
‹
Audio Setup
‹
Display Setup
‹
Parental Setup :
‹
DivX(R) Registration
‹
Enter
Return
Menu
AUDIO SETUP
Digital Out
: PCM
MPEG-2 Digital Out
: PCM
Dynamic Compression : On
PCM Down Sampling
Enter
Return
: On
Menu
❶ Digital Out
- PCM : Converts to PCM(2CH) audio.
- Bitstream : Outputs Dolby Digital via the digital
output. Select Bitstream when connecting to a
Dolby Digital Decoder.
Note :
- Even when PCM Down sampling is Off
• Some discs will only output down sampled audio
through the digital outputs.
- There is no analog audio output when you play a DTS
sound disc.
- To make the Setup menu disappear, press the
MENU button.
Language Setup
‹
Audio Setup
‹
Display Setup
‹
Parental Setup :
‹
DivX(R) Registration
‹
Anynet+(HDMI-CEC):On
Enter
Return
Menu
DVD-F1080 Dispay Setup
❶ TV Aspect
Depending on a type of television you have, you may want
to adjust the screen setting (aspect ratio).
- 4:3 Letter Box : Select when you want to see the total
16:9 ratio screen DVD supplies, even though you
have a TV with a 4:3 ratio screen. Black bars will
appear at the top and bottom of the screen.
- 4:3 Pan&Scan : Select this for conventional size TVs
when you want to see the central portion of the 16:9
screen. (Extreme left and right side of movie picture
will be cut off.)
- 16:9 Wide : You can view the full 16:9 picture on your
wide screen TV.
DISPLAY SETUP
HDMI (DVD-F1080 only)
- If your TV is not compatible with compressed multichannel formats (Dolby Digital, DTS, MPEG), you
should set Digital Audio to PCM.
- If your TV is not compatible with LPCM sampling
rates over 48kHz, you should set PCM Down sampling to On.
Enter
4:3 Letter Box
4:3 Pan&Scan
√ 16:9 Wide
: I-SCAN
: Off
Return
Menu
❷ Still Mode
- Auto : When selecting Auto, Field/Frame mode will be
automatically converted.
- Field : Select this feature when the screen shakes in
the Auto mode.
“DTS” and “DTS Digital Out” are trademarks of
Digital Theater Systems, Inc.
- Frame : Select this feature when you want to see
small letters more clearly in the Auto mode.
Setting Up the Display
Options
❸ Screen Messages
Use to turn on-screen messages On or Off.
Display options enable you to set various video functions of
the player.
1. With the unit in Stop mode, press the MENU button.
ƒ buttons to select Setup, then press the ‹
2. Press the œ/ƒ
or ENTER button.
ƒ buttons to select Display Setup, then
3. Press the œ/ƒ
press the ‹ or ENTER button.
ƒ buttons to select the desired item, then
4. Press the œ/ƒ
press the ‹ or ENTER button.
Language Setup
‹
Audio Setup
‹
Display Setup
‹
Parental Setup :
‹
DivX(R) Registration
‹
Return
: 16:9 Wide
Still Mode
Screen Message
TV System
Video Output
Black Level
These options will help prevent picture shake in still
mode and display small text clearer.
Manufactured under license from Dolby
Laboratories. “Dolby” and the double-D symbol
are trademarks of Dolby Laboratories.
Enter
Aspect
Ratio
TV Aspect
Menu
DVD-FP580 Dispay Setup
❹ TV System
- NTSC : In case of using NTSC disc
• If your TV system only has PAL-Video input, you must
choose “PAL”. When you choose “PAL”, Interlace output format is PAL 60 Hz output.
• If your TV system only has NTSC, input you must
choose “NTSC ”.
• If you set up the NTSC TV, HDMI output frame rate is 60 Hz.
- PAL : In case of using PAL disc
• If your TV system only has NTSC-Video input, you
must choose “NTSC”.
• If your TV system only has PAL input, you must
choose “PAL ”.
• If you set up the PAL TV, HDMI output frame rate is 50 Hz .
27
English
❷ MPEG-2 Digital Out
- PCM : Converts to PCM(2CH) audio.
- Bitstream : Converts to MPEG-2 Digital Bitstream
(5.1CH or 8CH). Select Bitstream when using the
Digital Audio Output.
❸ Dynamic Compression
- On : To select dynamic compression.
- Off : To select the standard range.
❹ PCM Down Sampling
- On : Select this when the Amplifier connected to the
player is not 96KHz compatible. In this case, the
96KHz signals will be down converted to 48KHZ.
- Off : Select this when the Amplifier connected to the
player is 96KHz compatible. In this case, all signals will
be output without any changes.
DISPLAY SETUP
TV Aspect
: Wide
Still Mode
: Auto
Screen Messages
: On
TV System
- Black Level (DVD-FP580 and DVD-F1080) : Adjusts
the brightness of the screen.(On or Off) It does not
NTSC
√ PAL
Video Output
Black Level
❼ Picture Quality / Black Level
function in Progressive mode.
: Off
- Brightness : Level 1 ~ Level 5
Enter
Return
Menu
- Contrast : Level 1 ~ Level 5
❺ Video Output
Select Video Output.
- Color Saturation : Level 1 ~ Level 5
- I-SCAN : Select when you want to use Component
Interlace (525i) Out.
DISPLAY SETUP
- P-SCAN : Select when you want to use Component
Progressive (525p) Out.
• If you press the VIDEO SEL. button when DVD
Player is in play mode, stop mode or no disc is
inserted, the Video Output mode changes in the
following sequence:
(I-SCAN ➝ P-SCAN)
TV Aspect
: Wide
Still Mode
: Auto
Screen Messages
: On
TV System
: PAL
Video Output
: I-SCAN
Black Level
: Off
Enter
Return
Menu
DVD-FP580
Black Level Menu
❻ HDMI (DVD-F1080 only)
PICTURE QUALITY
This setting is used when the unit is connected by HDMI
to Display devices (TV, Projector, etc.).
- Resolution Setting
Black Level
3
: Off
Brightness
: Level 3
Contrast
: Level 3
Color Saturation
: Level 3
- Auto : Resolution setting automatically
- Manual : Resolution setting manually
Enter
- Resolution
Return
Menu
DVD-F1080
Picture Quality Menu
• 480p/576p : 720 x 480, 720 x 480
4
• 720p : 1280 x 720
• 1080i : 1920 x 1080
• 1080p : 1920 x 1080
DISPLAY SETUP
TV Aspect
: Wide
Still Mode
: Auto
Screen Messages
: On
TV System
: PAL
Video Output
: I-SCAN
‹
HDMI
‹
Picture Quality
Enter
Return
Menu
HDMI SETUP
Resolution Setting
: Manual
Resolution
: 720p
Enter
28
Return
Menu
• Consult your TV User’s Manual to find
out if your TV supports Progressive Scan. If
Progressive Scan is supported, follow the
TV User’s Manual regarding Progressive
Scan settings in the TV’s menu system.
• If Video Output is set incorrectly, the screen
may be blocked.
• The resolutions available for HDMI output
depend on the connected TV or projector.
For details, see the user’s manual of your
TV or projector (DVD-F1080 only).
• When the resolution is changed during playback, it may take a few seconds for a normal image to appear.
• If you set the HDMI output resolution 720p,
1080p or 1080i, HDMI output provides better
picture quality (DVD-F1080 only).
5
6
Setting Up the Parental
Control
To make the setup menu disappear, press the MENU
button. For example, if you select up to Level 6, discs
that contain Level 7,8 will not play.
1. With the unit in Stop mode, press the MENU button.
ƒ buttons to select Setup, then press the ‹
2. Press the œ/ƒ
or ENTER button.
Changing the Password
1. With the unit in Stop mode, press the MENU button.
ƒ buttons to select Setup, then press the ‹
2. Press the œ/ƒ
or ENTER button.
Language Setup
‹
Audio Setup
‹
Language Setup
‹
Display Setup
‹
Audio Setup
‹
Parental Setup :
‹
Display Setup
‹
DivX(R) Registration
‹
Parental Setup :
‹
DivX(R) Registration
‹
Enter
Return
Menu
Enter
Return
Menu
ƒ buttons to select Parental Setup, then
3. Press the œ/ƒ
press the ‹ or ENTER button.
ƒ buttons to select Parental Setup, then
3. Press the œ/ƒ
press the ‹ or ENTER button.
Language Setup
‹
Language Setup
‹
Audio Setup
‹
Audio Setup
‹
Display Setup
‹
Display Setup
‹
Parental Setup :
‹
Parental Setup :
‹
DivX(R) Registration
DivX(R) Registration
‹
Enter
Enter
Return
Return
‹
Menu
Menu
ƒ buttons to select Rating Level, then press
4. Press the œ/ƒ
the ‹ or ENTER button.
ƒ button to select Change Password, then
4. Press the œ/ƒ
press the ‹ or ENTER button. Enter your new password.
Re-enter the new password again.
PARENTAL SETUP
Rating Level
PARENTAL SETUP
: Kids Safe
Rating Level
Change Password
:Kids Safe
Change Password
Enter
Return
Menu
5. Enter your password.
- By default, password is set to 0000.
- Please change password to other than 0000 to
activate parental control function.
Enter
Return
Menu
PARENTAL SETUP
Rating Level
:Kids Safe
Change Password
PARENTAL SETUP
Rating Level
Enter Password
: Kids Safe
Change Password
Enter Password
Enter
Return
Menu
PARENTAL SETUP
Enter
Return
Menu
ƒ buttons to select the Rating Level you want,
6. Press the œ/ƒ
then press the ‹ or ENTER button.
e.g) Setting up in Kids Safe.
Rating Level
:Kids Safe
Change Password
Enter New Password
PARENTAL SETUP
Enter
Rating
RatingLevel
Level
Change Passwor
Enter
Return
Return
Menu
: Kids Safe
√ Kids Safe
Level 2
Level 3
Level 4
Level 5
Level 6
Note
If you have forgotten your password, see
“Forgot Password” in the Troubleshooting Guide.
Menu
29
English
The Parental Control function works in conjunction
with DVDs that have been assigned a rating, which
helps you control the types of DVDs that your family
watches. There are up to 8 rating levels on a disc.
Setting Up the Rating Level
Setting Up the Anynet+
(HDMI-CEC) (DVD-F1080 only)
Anynet+ is a function that can be used to operate
the unit using a Samsung TV remote control, by
connecting the DVD-F1080 to a SAMSUNG TV
using a HDMI Cable. (see page 12) (This is only
available with SAMSUNG TVs that support
Anynet+).
Note
To make the Setup menu disappear, press the
MENU button.
• You can operate the DVD Player by using TV
remote control. (TV buttons that can be used to con
trol the DVD Player :
,
,
,
,
Select On when you connecting the DVD-F1080
with Samsung TV that support Anynet+.
,
,
,and
buttons,
buttons.).
- Select Device : Use this option to select device.
1. With the unit in Stop mode, press the MENU button.
ƒ buttons to select Setup, then press the ‹
2. Press the œ/ƒ
or ENTER button.
Language Setup
‹
Audio Setup
‹
Display Setup
‹
Parental Setup :
‹
DivX(R) Registration
‹
Anynet+(HDMI-CEC):On
Enter
Return
Menu
ƒ buttons to select Anynet+(HDMI-CEC),
3. Press the œ/ƒ
then press the ‹ or ENTER button.
Language Setup
‹
Audio Setup
‹
Display Setup
‹
Parental Setup :
‹
DivX(R) Registration
‹
Anynet+(HDMI-CEC):On
Enter
Return
Menu
4. Set the Anynet+(HDMI-CEC) to “On” on your DVD Player,
then press the ‹ or ENTER button.
Language Setup
‹
Audio Setup
‹
Display Setup
‹
Parental Setup :
‹
DivX(R) Registration
Off
√ On
Anynet+(HDMI-CEC):On
‹
Enter
Return
Menu
5. Set the Anynet+ function at your TV. (See the TV instruction
manual for more information.).
• When you press Anynet+ button on the TV remote
control, the below OSD will appear.
DVDP
View TV
®
Select Device
®
Record
®
Menu on Device
®
Device Operation
®
Receiver : Off
®
Setup
®
Move
Exit
ENTER
TV Menu
30
- Menu on Device : Same as MENU button on the
DVD Player remote control.
- Device Operation : Same as INFO button on the
DVD Player remote control.
Note
• By pressing the PLAY button of the unit while watching TV, the TV screen will change to the play screen.
• If you play a DVD when the TV power is off, the TV
will power On.
• If you turn the TV off , the DVD Player will power
off automatically.
• If you change the HDMI to other sources
(Composite,Component,... etc) in TV while play
ing the DVD disc, the DVD Player will stop play
ing.
REFERENCE
Firmware upgrade
2. Press the ¦/‹ buttons to select Total, then press the
ENTER button.
English
Introduction
Samsung will often support the software upgrade to
improve the performance of this unit to the latest
status, through Samsung Internet Site
(www.samsung.com).
.
Because the specially new mpeg4 codec continues and
it is appearing. What improvements are made depends
on the upgrade software you are using as well as the
software that your DVD-player contained before the
upgrade.
How to make an upgrade disc
Write the downloaded file onto a blank CD-R or CDRW disc, using the following settings:
Firmware upgrade starts
- In the middle of the writing, the tray will open
automatically. After taking out the disc, please wait for
about 2 minutes.
- If the unit was succesfully updated, the unit will turn off
and on after closing the tray automatically. When the
unit turns on, this screen will display.
3. Press the number buttons to select the desired language
1. You have to download a new file through Download Center
of Samsung Internet Site (www.samsung.com).
2. Write the file to Disc using CD-RW of your computer.
Note
- File System CD-ROM ISO Level
- Character set ISO 9660
- Finalized, single session
- Write speed low
Upgrade procedure
1. Open the disc tray. Place the disc on the tray. Close the
tray. The Firmware upgrade screen appears.
Press
Touche
Drücken Sie
Pulsar
Premere
Druk op
1
2
3
4
5
6
for English
pour Français
für Deutsch
para Español
per Italiano
voor Nederlands
Note
- If the “Select Menu Language” doesn’t appear,
please contact to “Samsung Service Center”.
- Do not press any button and unplug the power
code during upgrade.
- The upgrade procedure may change, refer to
the web site (www.samsung.com).
Firmware upgrade
appears on the display
31
Troubleshooting
Before requesting service (troubleshooting), please check the following.
Action
Problem
Page
No operations can be
performed with the
remote control.
• Check the batteries in the remote control.
They may need replacing.
• Operate the remote control at a distance of no more than 20 feet.
• Remove batteries and hold down one or more buttons for several minutes to drain
the microprocessor inside the remote control to reset it. Reinstall batteries and try
to operate the remote control again.
P3
Disc does not play.
• Ensure that the disc is installed with the label side facing up.
• Check the region number of the DVD.
P5
5.1 channel sound is
not being reproduced.
The
icon appears
on screen.
• 5.1 channel sound is reproduced only when the following conditions are met. :
1) The DVD player is connected with the proper Amplifier
2) The disc is recorded with 5.1 channel sound.
• Check whether the disc being played has the “5.1 ch” mark on the outside.
• Check if your audio system is connected and working properly.
• In a SETUP Menu, is the Audio Output set to Bitstream?
• The features or action cannot be completed at this time because:
1. The DVD’s software restricts it.
2. The DVD’s software doesn’t support the feature (e.g., angles).
3. The feature is not available at the moment.
4. You’ve requested a title or chapter number or search time that is out of range.
P13-14
P26~27
Disc Menu doesn’t appear. • Check if the disc has a Menu.
Play mode differs from the • Some of the functions selected in the Setup Menu may not work properly if the
disc is not encoded with the corresponding function.
Setup Menu selection.
P25~30
The screen ratio
cannot be changed.
• The Screen Ratio is fixed on your DVDs.
P27~28
No audio.
• Make sure you have selected the correct Digital Output in the Audio Options
Menu.
P26~27
The screen is blocked
• Press the
button (in front panel) for more than 5 seconds under no disc
inside. All settings will revert to the factory settings.
P15
Forgot password
• Press the
button (in front panel) for more than 5 seconds
under no disc inside. All settings including the password will revert to the factory
settings. Don't use this unless absolutely necessary.
If you experience
other problems.
• Go to the contents and find the section of the instruction book that contains the
explanations regarding the current problem, and follow the procedure once again.
• If the problem still cannot be solved, please contact your nearest authorized service center.
The picture is noisy or
distorted
• Make sure that the disc is not dirty or scratched.
• Clean the disc.
No HDMI output.
(DVD-F1080 only)
• Check the Video output is HDMI enabled.
• Check the connection between the TV and the HDMI jack of DVD player.
• See if the TV supports this 480p/576p/720p/1080i/1080p DVD player.
P12~13
Abnormal HDMI output
screen. (DVD-F1080
only)
• If snow noise appears on the screen, it means that TV does not support HDCP
(High-bandwidth Digital Content Protection).
P12~13
• Check your TV system setup correctly.
• The screen Jitter phenomenon may occur when frame rate is converted from
50Hz to 60Hz for 720P/1080i/1080p HDMI (High Definition Multimedia Interface)
Output.
• Please refer to the user’s manual of your TV.
P27~28
HDMI output Jitter
(DVD-F1080 only)
32
P29
P2
Specifications
AC 110-240V ~ 50/60 Hz
Power Consumption
7W
Weight
Dimensions
0.976 Kg
240mm (W) X 240mm (D) X 50.5mm (H)
Operating Temperature Range
+5°C to +35°C
Operating Humidity Range
10 % to 75 %
DVD
(DIGITAL VERSATILE DISC)
English
General
Power Requirements
Reading Speed : 3.49 ~ 4.06 m/sec.
Approx. Play Time
(Single Sided, Single Layer Disc) : 135 min.
CD : 12Cm
Disc
(COMPACT DISC)
CD : 8Cm
(COMPACT DISC)
VCD : 12Cm
Composite Video
Component Video
HDMI
Output
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 20 min.
Reading Speed : 4.8 ~ 5.6 m/sec.
Maximum Play Time : 74 min. (Video + Audio)
1 channel : 1.0 Vp-p (75 Ω load)
Pr : 0.70 Vp-p (75 Ω load)
Pb : 0.70 Vp-p (75 Ω load)
2 Channel
Audio
Maximum Play Time : 74 min.
Y : 1.0 Vp-p (75 Ω load)
Video
Output
Reading Speed : 4.8 ~ 5.6 m/sec.
*Frequency Response
480p/576p. 720p. 1080i. 1080p (DVD-F1080 only)
L(1/L), R(2/R)
48 kHz Sampling : 4 Hz to 22 kHz
96 kHz Sampling : 4 Hz to 44 kHz
*S/N Ratio
110 dB
*Dynamic Range
100 dB
*Total Harmonic Distortion
0.004 %
*: Nominal specification
- Samsung Electronics Co., Ltd reserves the right to change the specifications with out notice.
- Weight and dimensions are approximate.
33
81,7('.,1*'20
7KLV6DPVXQJSURGXFWLVZDUUDQWHGIRUWKHSHULRGRI
WZHOYHPRQWKVIURPWKHRULJLQDOGDWHRI
SXUFKDVHDJDLQVWGHIHFWLYHPDWHULDOVDQG
ZRUNPDQVKLS,QWKHHYHQWWKDWZDUUDQW\VHUYLFHLV
UHTXLUHG\RXVKRXOGUHWXUQWKHSURGXFWWRWKHUHWDLOHU
IURPZKRPLWZDVSXUFKDVHG
+RZHYHU6DPVXQJ$XWKRULVHG'HDOHUVDQG
$XWKRULVHG6HUYLFH&HQWUHVLQRWKHU(&&RXQWULHVZLOO
FRPSO\ZLWKWKHZDUUDQW\RQWKHWHUPVLVVXHGWR
SXUFKDVHUVLQWKHFRXQWU\FRQFHUQHG
,QFDVHRIGLIILFXOW\GHWDLOVRIRXU$XWKRULVHG6HUYLFH
&HQWUHVDUHDYDLODEOHIURP
6DPVXQJ(OHFWURQLFV8./WG
&XVWRPHU&DUH&HQWUH32%R[(GLQEXUJK
(+<%8QLWHG.LQJGRP
8QLWHG.LQJGRP
7HO6$0681*
)D[
:HEZZZVDPVXQJFRP
EIRE
7HO
)D[
:HEwww.samsung.com
„:$55$17<&21',7,216
7KHZDUUDQW\LVRQO\YDOLGLIZKHQZDUUDQW\VHUYLFH
LVUHTXLUHGWKHZDUUDQW\FDUGLVIXOO\DQGSURSHUO\
FRPSOHWHGDQGLVSUHVHQWHGZLWKWKHRULJLQDOLQYRLFH
RUVDOHVVOLSRUFRQILUPDWLRQDQGWKHVHULDOQXPEHU
RQWKHSURGXFWKDVQRWEHHQGHIDFHG
6DPVXQJ¶VREOLJDWLRQVDUHOLPLWHGWRWKHUHSDLURU
DWLWVGLVFUHWLRQUHSODFHPHQWRIWKHSURGXFWRUWKH
GHIHFWLYHSDUW
:DUUDQW\UHSDLUVPXVWEHFDUULHGRXWE\$XWKRULVHG
6DPVXQJ'HDOHUVRU$XWKRULVHG6HUYLFH&HQWUHV
1RUHLPEXUVHPHQWZLOOEHPDGHIRUUHSDLUVFDUULHG
RXWE\QRQ6DPVXQJ'HDOHUVDQGDQ\VXFKUHSDLU
ZRUNDQGGDPDJHWRWKHSURGXFWVFDXVHGE\VXFK
UHSDLUZRUNZLOOQRWEHFRYHUHGE\WKLVZDUUDQW\
EIRE
7KLVSURGXFWLVQRWFRQVLGHUHGWREHGHIHFWLYH
LQPDWHULDOVQRUZRUNPDQVKLSE\UHDVRQWKDWLW
UHTXLUHVDGDSWDWLRQLQRUGHUWRFRQIRUPWRQDWLRQDO
RUORFDOWHFKQLFDORUVDIHW\VWDQGDUGVLQIRUFHLQ
DQ\&RXQWU\RWKHUWKDQWKHRQHIRUZKLFKWKH
SURGXFWZDVRULJLQDOO\GHVLJQHGDQGPDQXIDFWXUHG
7KLVZDUUDQW\ZLOOQRWFRYHUDQGQRUHLPEXUVH
PHQWZLOOEHPDGHIRUVXFKDGDSWDWLRQQRUDQ\
GDPDJHZKLFKPD\UHVXOW
7KLVZDUUDQW\FRYHUVQRQHRIWKHIROORZLQJ
D3HULRGLFFKHFNXSVPDLQWHQDQFHDQGUHSDLURU
UHSODFHPHQWRISDUWVGXHWRQRUPDOZHDUDQG
WHDU
E&RVWUHODWLQJWRWUDQVSRUWUHPRYDORULQVWDOODWLRQ
RIWKHSURGXFW
F0LVXVHLQFOXGLQJWKHIDLXUHWRXVHWKLVSURGXFW
IRULWVQRUPDOSXUSRVHVRULQFRUUHFWLQVWDOODWLRQ
G'DPDJHFDXVHGE\/LJKWQLQJ:DWHU)LUH$FWV
RI*RG:DU3XEOLF'LVWXUEDQFHVLQFRUUHFW
PDLQVYROWDJHLPSURSHUYHQWLODWLRQRUDQ\RWKHU
FDXVHEH\RQGWKHFRQWURORI6DPVXQJ
7KLVZDUUDQW\LVYDOLGIRUDQ\SHUVRQZKROHJDOO\
DFTXLUHGSRVVHVVLRQRIWKHSURGXFWGXULQJWKH
ZDUUDQW\SHULRG
7KHFRQVXPHUVVWDWXWRU\ULJKWVLQDQ\DSSOLFDEOH
QDWLRQDOOHJLVODWLRQZKHWKHUDJDLQVWWKHUHWDLOHU
DULVLQJIURPWKHSXUFKDVHFRQWUDFWRURWKHUZLVH
DUHQRWDIIHFWHGE\WKLVZDUUDQW\8QOHVVWKHUHLV
QDWLRQDOOHJLVODWLRQWRWKHFRQWUDU\WKHULJKWVXQGHU
WKLVZDUUDQW\DUHWKHFRQVXPHUVVROHULJKWVDQG
6DPVXQJLWVVXEVLGLDULHVDQGGLVWULEXWRUVVKDOOQRW
EHOLDEOHIRULQGLUHFWRUFRQVHTXHQWLDOORVVRUDQ\
GDPDJHWRUHFRUGVFRPSDFWGLVFVYLGHRVRUDXGLR
WDSHURUDQ\RWKHUUHODWHGHTXLSPHQWRUPDWHULDO
6$0681*(/(&7521,&68./7'
Contact SAMSUNG WORLD WIDE
If you have any questions or comments relating to Samsung products,
please contact the SAMSUNG customer care centre.
☎ 0845 - SAMSUNG(7267864)/ www.samsung.com
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems)
This marking shown on the product or its literature, indicates that it should not be disposed with other household
wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable
reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local
ce, for details of where and how they can take this item for environmentally safe recycling.
government
Business users should contact their supplier and check the terms and conditions of the purchase
contract. This product should not be mixed with other commercial wastes for disposal.
AK68-01464N(02)
Download PDF