Ficha técnica 1: FX101PZ - FX101PZ | FX-101P-Z

Ficha técnica 1: FX101PZ - FX101PZ | FX-101P-Z
DIGITAL FIBER SENSOR
FX-100SERIES
Conforming to
EMC Directive
Bringing digital fiber sensors closer
New possibilities with digital fiber sensors.
The FX series is a round 100 for success.
Easy to read, multipurpose, and at an economical price.
The FX series has been designed to be what customers want it to be.
Take a step into the new world that starts with ‘100’.
Easy to read
The digital dual-display shines out in the workplace!
The digital dual-display allows you to check both the threshold
value and incident light intensity at the same time, and it also
makes the procedures for setting the various values much easier.
The threshold values can be adjusted simply by pressing the
(UP) key or the
(DOWN) key, so that the sensors can
be used at the same sensitivity levels as analog control-type
sensors. And of course a key lock function is also included.
Threshold value
Incident light intensity
General purpose
Commercially-availabie connectors
are used so that lead time and spare
part numbers can both be reduced.
The connectors used are commerciallyavailable connectors, so that processing
costs and lead time required for carrying out
processing after purchase of the sensors can
be greatly reduced. The same connection
parts as the DP-100 series of digital pressure
sensors and the PM-64 series of micro
photoelectric sensors can be used.
Commercially-available press-fit connectors are used, so that the processing costs for connection cables can be greatly reduced.
Conventional (cable type)
Conventional lead time
;Harness
ss processing
p
by outside order after sensor preparation
Customer Sensor preparation
1 Sensor purchase and preparation
2 Harness processing by outside order
Harness
processor
From now on (built-in connector type)
Sensor installation
Harness Processing
Lead time from now on
;Harness
ss processing
p
by outside order
Customer Sensor preparation
1 Sensor purchase and preparation
2 Harness processing by outside order
Harness
processor
Using cables with connectors
Sensor installation
Lead time further reduced
Customer Sensor preparation Sensor installation
Reduced
1 Purchase of sensors and cable with connectors
SUNX fiber sensor product lineup
Select the best types to suit your application.
Digital type
FX-300 (High function)
FX-410 (Volume setting)
FX-100
Analog control-type
1
Reduced
Harness Processing
FX-101 (Standard type)
FX-102 (Long sensing range type)
FX-311 (General purpose)
Reduced
lead time
Digital fiber sensor
DIN rail
installation also
possible
9
mm
0.354 in thickness
"3.2 "0.126 mounting hole
Direct installation possible without bracket
Designed in a 3-layer structure to accommodate basic settings through to
advanced settings.
Setting details are divided into three levels for clearer operation, so that settings for normal operation are
made in ‘RUN mode’, basic settings are made in ‘SET mode’, and advanced functions are set in ‘PRO mode’.
This makes setting operations much easier to understand and carry out.
RUN mode
Functions used during normal operation
RUN MODE
Simple setting
[ function table ]
• Changing threshold values • Key lock
• Quick settings • Code settings
SET mode
Functions used when initializing the
sensor and carrying out maintenance
[ function table ]
SET MODE
• Teaching • L-ON / D-ON setting
• Timer setting
• Light-emitting amount selection
• Emission frequency setting function
PRO mode
Equipped with a full complement
of digital fiber sensor functions
PRO MODE
Special and detailed setting
The same operating system is shared by the widely-acclaimed
DP-100 series of digital pressure sensors. The ‘100’ is the indicator
for easy handling.
[ function table ]
• Shift • External input • Reset
• GETA • ECO • Display reversing
• Surplus value display • Copy
• Threshold value seeking cycle setting
Digital pressure sensor
DP-100 series
2
Easy for inexperienced operators to use,
and experienced operators will still be satisfied too.
Introducing sensors with a full complement of functions
to support the needs of your workplace.
Changing threshold values
Quick code input function
For
For
factory
operators designers
Sensor settings can be made simply by selecting preset
values.
Key lock
Quick settings
Code settings
Quick setting numbers (summary)
No.
Output operation
Light-emitting
amount selection
Dark-ON
OFF
None
Dark-ON
ON
None
Dark-ON
OFF
OFF-delay 10 ms
Dark-ON
ON
OFF-delay 10 ms
Light-ON
ON
ON-delay 40 ms
Light-ON
OFF
ON-delay 40 ms
Light-ON
ON
ON-delay 10 ms
Light-ON
OFF
ON-delay 10 ms
Timer
Smooth support via telephone
Confirmation can be carried out smoothly via telephone by
simply quoting numbers. This can be of great assistance
when dealing with overseas customers.
3
Teaching
L-ON / D-ON setting
Teaching using ON / OFF buttons
For
factory
operators
Simply press the ON button when an object is present
and OFF when it is not. There is no need to switch
)
settings or make judgments between Light-ON (
and Dark-ON (
).
<Setting example>
Thru-beam type
Timer setting
Light-emitting amount selection
Interference prevention function
If the light receiving level becomes saturated when sensing
over short distances or when sensing transparent objects
or minute objects, the light emitting amount can be adjusted
so that stable sensing can be provided without needing to
change the response time.
Emission frequency setting function
(
Object present ON
Object absent OFF
For
designers
Light-emitting amount selection function
)
For
factory
operators
The emission frequencies can be set separately for each
unit in order to avoid interference. The emitted light flashes
while setting is in progress, so that you can see at a glance
which fiber sensor is currently being set. In addition,
this interference prevention is not done by using optical
communication. This means that there is no need to place
the amplifiers close together like there was before, and so
the amplifiers can be set up apart from each other.
Reflective type
mWhen the emission frequencies are changed, the response times will
also change.
Object present ON
Object absent OFF
Limit teaching function
This carries out teaching and sets threshold values only
when no object is present (when the incident light amount is
stable). This is useful when sensing objects if there are other
objects in the background and when sensing minute objects.
Teaching can also be carried out using external input.
Shift
External input
This function seeks changes in the light
emitting amount resulting from changes
in the environment over long periods
(such as dust levels), so that the incident
light intensity can be checked at desired
intervals and the threshold values can
For
factory
operators
Current value
Threshold value
GETA
ECO
Display reversing
Surplus value display
Copy
Reset
External input function
Settings such as emission
(Brown) V
halt, limit / auto teaching
(Black) Output
and ECO settings can be
(White) External input
carried out via external
(Blue) 0 V
input.
External input lines are equipped as standard
Time
(Price)
be reset automatically.
Incident light intensity
Threshold value seeking cycle setting function
Threshold value seeking cycle setting
The functions and performance of a digital fiber sensor at an
easily-affordable price!
;Digital type
FX-300
FX-411
;Analog control-type
SUNX digital-type sensors have never been more accessible than this. And they are
ideal as replacement products for analog control types and teaching types also.
FX-100
target
;Teaching type
Performance (sensing range), operability
4
FX-100
ORDER GUIDE
Amplifiers
Appearance
Model No.
M8 plug-in
connector type
Cable set (Note 1)
Standard type
M8 plug-in
connector type
Type
Accessory
Emitting
element
Output
FX-101 (Note 2)
NPN open-collector
transistor
FX-101-Z (Note 3)
NPN open-collector
transistor
FX-101P (Note 2)
PNP open-collector
transistor
FX-101P-Z (Note 3)
PNP open-collector
transistor
FX-101-CC2
NPN open-collector
transistor
FX-101P-CC2
PNP open-collector
collector transistor
• CN-14A-C2
(
6.562 ft
)
mOnly include cable set type
M8 plug-in
connector type
M8 plug-in
connector type
Cable set (Note 1)
Long sensing range type
Red LED
FX-102 (Note 2)
NPN open-collector
transistor
FX-102-Z (Note 3)
NPN open-collector
transistor
FX-102P (Note 2)
PNP open-collector
transistor
FX-102P-Z (Note 3)
PNP open-collector
transistor
FX-102-CC2
NPN open-collector
transistor
FX-102P-CC2
PNP open-collector
transistor
Notes: 1) The connector attached cable CN-14A-C2 is supplied with the amplifier.
2) Make sure to use the optional connector attached cable CN-14A-C or the connector CN-14A.
3) Make sure to use the optional M8 connector attached cable CN-24A-C.
OPTIONS
M8 connector attached cable
Designation
Model No.
Description
31.4
1.236
CN-14A-C1 1 m 3.281 ft
Connector
attached cable
CN-14A-C2 2 m 6.562 ft
(Note)
CN-14A-C3 3 m 9.843 ft
0.02 mm2 4-core cabtyre cable
with connector on one end
Cable outer diameter: "3.7 mm "0.146 in
CN-14A-C5 5 m 16.404 ft
CN-24A-C5
For M8 plug-in connector type
The connector on one end
5 m 16.404 ft Cable outer diameter: "4 mm "0.157 in
Connector
CN-14A
Set of 10 housings and 40 contacts
Protection cover
FC-FX-1
This protects the operating surfaces.
Amplifier mounting
bracket
MS-DIN-4
Mounting bracket for amplifier
MS-DIN-E
When it moves depending on the way it is installed on a DIN rail,
these end plates ensure that all amplifiers are mounted together in
a secure and fully connected manner.
M8 connector
attached cable
End plates
CN-24A-C2 2 m 6.562 ft
Two pcs. per set
Note: The connector attached cable CN-14A-C2 is supplied with the cable set type FX-10(P)-CC2.
M8 connector
attached cable
CN-24A-CI
• CN-24A-C
"4
"0.157
"9
"0.354
Fixing ring
Protection cover
• FC-FX-1
Amplifier mounting bracket
• MS-DIN-4
Connector attached cable
• CN-14A-C
Connector
Contact
•
Housing
5
FX-100
SPECIFICATIONS
Item
Model No.
Type
Standard type
Long sensing range type
Cable set
Cable set
NPN output
FX-101 (-Z) (Note 4)
FX-101-CC2
FX-102 (-Z) (Note 4)
FX-102-CC2
PNP output
FX-101P (-Z) (Note 4)
FX-101P-CC2
FX-102P (-Z) (Note 4)
FX-102P-CC2
12 to 24 V DC10 % Ripple P-P 10 % or less
Supply voltage
Power consumption
Output
Normal operation: 720 mW or less (Current consumption 30 mA or less at 24 V supply voltage)
ECO mode: 600 mW or less (Current consumption 25 mA or less at 24 V supply voltage)
<NPN output type>
NPN open-collector transistor
• Maximum sink current:100 mA
• Applied voltage: 30 V DC or less (between output and 0 V)
• Residual voltage: 1.5 V or less (at 100 mA sink current)
Output operation
Selectable either Light-ON or Dark-ON, at SET mode
Short-circuit protection
External input
Response time
Incorporated
<NPN output type>
NPN non-contact input
• Signal condition
High: 8 V to V DC or Open
Low: 0 to2 V DC
(Source current 0.5 mA or less)
• Input impedance: 10 kΩ approx.
<PNP output type>
PNP non-contact input
• Signal condition
High: 4 V toV DC
(Sink current 0.5 to 3 mA)
Low: 0 to0.6 V DC or Open
• Input impedance: 10 kΩ approx.
Emission frequency 0: 250 !s or less
Emission frequency 1: 450 !s or less
Emission frequency 2: 500 !s or less
Emission frequency 3: 600 !s or less
Sensitivity setting
Emission frequency 1: 2.5 ms or less
Emission frequency 2: 2.8 ms or less
Emission frequency 3: 3.2 ms or less
Emission frequency 4: 5.0 ms or less
2-level teaching / Limit teaching / Full-auto teaching
Operation indicator
Orange LED (lights up when the output is ON)
4 digits (green)4 digits (red) LCD display
Digital display
Fine sensitivity adjustment function
Timer function
Incorporated
ON-delay / OFF-delay timer, switchable either effective or ineffective.
[Timer period:1 ms, 5 ms, 10 ms, 20 ms, 40 ms, 50 ms, 100 ms, 500 ms, 1,000 ms]
Light emitting amount selection
function
Environmental resistance
Interference prevention
function
Ambient temperature
Incorporated / Switchable either effective or ineffective
Incorporated
Emission frequency selection method (Note 2)
(Functions at emission frequency 1, 2 or 3)
Incorporated
Emission frequency selection method (Note 2)
(Functions at emission frequency 1, 2 , 3 or 4)
10 to 55 C 14 to 131 F (If 4 to 7 units are mounted close together: 10 to 50 C 14 to 122 F, if 8 to 16 units are :
10 to 45 C 14 to 113 F) (No dew condensation or icing allowed), Storage: 20 to 70 C 4 to 158 F
Ambient humidity
35 to 85 % RH, Storage: 35 to 85 % RH
Incandescent light: 3,000 ?x at the light-receiving face
Ambient illuminance
Voltage withstandability
<PNP output type>
PNP open-collector transistor
• Maximum source current: 100 mA
• Applied voltage: 30 V DC or less (between output and V)
• Residual voltage: 1.5 V or less (at 100 mA source current)
1,000 V AC for one min. between all supply terminals connected together and enclosure (Note 3)
Insulation resistance
20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure (Note 3)
Vibration resistance
10 to 150 Hz frequency, 0.75 mm 0.030 in amplitude in X, Y and Z directions for two hours each
Shock resistance
98 m/s2 acceleration (10 G approx.) in X, Y and Z directions for five times each
Emitting element (modulated)
Material
Red LED (Peak emission wavelength : 632 nm)
Enclosure: Polycarbonate, Key switch: Polycarbonate, Fiber lock lever: PBT
Connecting method
Cable extension
Weight
Accessory
Connector (Note 4)
Total length up to 100 m 328.084 ft is possible with 0.3 mm2, or more, cable.
Net weight: 15 g approx.
Gross weight: 35 g approx.
Net weight: 15 g approx.
Gross weight: 75 g approx.
CN-14A-C2
(Connector attached cable, 2 m 6.562 ft long):1pc.
Net weight: 15 g approx.
Gross weight: 35 g approx.
Net weight: 15 g approx.
Gross weight: 75 g approx.
CN-14A-C2
(Connector attached cable, 2 m 6.562 ft long):1pc.
Notes: 1) Where measurement conditions have not been specified precisely, the conditions used were ambient temperature 23 C 73.4 F.
2) When using the interference prevention function, set the emission frequencies for the amplifiers to be covered by the interference prevention
function to different frequency values.
However, the interference prevention function does not operate at emission frequency 0 (factory default setting) for the FX-101(P)(-Z) / FX-101(P)-CC2.
3) The voltage withstandability and the insulation resistance values given in the above table are for the amplifier only.
4) Connector attached cable CN-14A-C2 is not attached to the models that have no ‘-CC2’ at the end of the model Nos.
Make sure to use the optional connector attached cable CN-14A-C or the connector CN-14A.
Model Nos. having the suffix ‘-Z’ are M8 plug-in connector type. Make sure to use the optional M8 plug-in connector cable CN-24A-C.
6
FX-100
I/O CIRCUIT AND WIRING DIAGRAMS
FX-10((-Z/-CC2))
NPN output type
I/O circuit diagram
Terminal arrangement diagram
Connector type
Terminal No.
Color code of cable with connector
(Brown) V
1
Sensor circuit
D
Tr
8 V
ZD
(White) Extemal input
3
Internal circuit
12 to 24 V DC
10 %
2
3
4
m1
(Blue) 0 V
4
Terminal No.
1
Load
(Black) Output
2
100 mA max.
Function
1
V
2
Output
3
External input
4
0V
Users’ circuit
Symbols ... D : Reverse supply polarity protection diode
ZD : Surge absorption zener diode
Tr : NPN output transistor
M8 plug-in connector type
m1
Non-voltage contact or NPN open-collector transistor
1
Terminal No.
2
or
3
High (8 V to V DC or open): Ineffective
Low [(0 to 2 V DC (source current 0.5 mA or less)] : Effective
4
Function
1
V
2
Output
3
External input
4
0V
FX-10P((-Z/-CC2))
PNP output type
I/O circuit diagram
Terminal arrangement diagram
Terminal No.
Connector type
Color code of cable with connector
Sensor circuit
(Brown) V
1
m1
(White) External input
3
ZD
Tr
D
Internal circuit
100 mA max.
2
(Black) Output
(Blue) 0 V
4
Load
Terminal No.
1
12 to 24 V DC
10 %
2
3
4
V
2
Output
3
External input
4
0V
Users’ circuit
Symbols ... D : Reverse supply polarity protection diode
ZD : Surge absorption zener diode
Tr : PNP output transistor
M8 plug-in connector type
m1
Non-voltage contact or PNP open-collector transistor
1
Terminal No.
2
or
High [4 V to V DC (sink current 0.5 to 3 mA)]: Effective
Low (0 to 0.6 V DC or open): Ineffective
7
Function
1
3
4
Function
1
V
2
Output
3
External input
4
0V
FX-100
LIST OF FIBERS
Pliable fibers (flexible and sharp bending fibers) are marked with light blue in the table.
Thru-beam type (one pair set)
Type
Shape of fiber head
(mm in)
Lens mountable
Standard type FX-101
M4
Lens mountable
Fiber cable Bending
length
Long sensing range type FX-102
: Free-cut radius
Sensing range (mm in)(Note)
400 15.748
FT-B8
1,150 45.276
R25 mm
R0.984 in
M4
FT-FM2
Sleeve 90 mm 3.543 in M4
M4
800 31.496
300 11.811
"1.48 "0.058
Sleeve 40 mm 1.575 in
2m
6.562 ft
M4
"1.48 "0.058
Lens mountable
M4
Lens mountable
M4
Lens mountable
260 10.236
230 9.055
FT-FM2S4
FT-W8
650 25.591
R4 mm
R0.157 in
Flexible
FT-P80
1m
3.281 ft
R10 mm
R0.394 in
FT-P81X
2m
6.562 ft
R4 mm
R0.157 in
Flexible
FT-P60
260 10.236
800 31.496
M4
300 11.811
Nut type
M4
Lens mountable
Lens mountable
(except FX-LE2)
570 22.441
215 8.465
W7H9D13.9
W0.276H0.354D0.547
With lens
M4
430 16.929
W7H9D14.6
W0.276H0.354D0.575
Elbow
Threaded type
FT-FM2S
R1 mm
R0.039 in
Tough flexible
130 5.118
Fiber
R25 mm
R0.984 in
Sleeve
R10 mm
R0.394 in
650 25.591
M4
Lens mountable
Model No.
M4
430 16.929
180 7.087
M3
1,150 45.276
2m
6.562 ft
2m
6.562 ft
M3
M3
"0.88 "0.035
Sleeve 40 mm 1.575 in
FT-T80
FT-NFM2
130 5.118
280 11.024
2m
6.562 ft
"0.88 "0.035
Long sensing
range
g
M3
With lens
FT-R80
R25 mm
R0.984 in
M3
M3
R25 mm
R0.984 in
800 31.496
300 11.811
FT-WR80
FT-WR80L
M3
Sleeve 90 mm 3.543 in
R1 mm
R0.039 in
Fiber
R25 mm
R0.984 in
Sleeve
R10 mm
R0.394 in
FT-NFM2S
FT-NFM2S4
80 3.150
220 8.661
R1 mm
R0.039 in
FT-W4
80 3.150
240 9.449
R4 mm
R0.157 in
Flexible
FT-P40
M14
9,300 366.141
15,000 590.550
10 m
32.808 ft
R25 mm
R0.984 in
FT-FM10L
Note: Please take care that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut.
8
FX-100
LIST OF FIBERS
Pliable fibers (flexible and sharp bending fibers) are marked with light blue in the table.
Thru-beam type (one pair set)
"3 "0.118
Type
Shape of fiber head
(mm in)
Standard type FX-101
With lens • Long sensing range
"3 "0.118
600 23.622
"3 "0.118
"2.5 "0.098
"1.5 "0.059
Cylindrical type
Ultra-small diameter "1
"0.039
"1 "0.039
Beam diameter
"0.125 mm "0.005 in
"0.25 "3
"0.010 "0.118
800 31.496
300 11.811
"0.4 "3
"0.016 "0.118
FT-SFM2L
130 5.118
R1 mm
R0.039 in
R25 mm
R0.984 in
280 11.024
2m
6.562 ft
220 8.661
80 3.150
1m
3.281 ft
330 12.992
120 4.724
500 mm
19.685 in
90 3.543
40 1.575
1m
3.281 ft
60 2.362
15 0.591
R1 mm
R0.039 in
Sleeve part cannot be bent.
"1.5 "0.059
Side-view
0.88 0.031
0
"2.5 "0.098
180 7.087
470 18.504
Sleeve p
part cannot be bent.
"1 "0.039
0.66 0.024
0
"2 "0.079
140 5.512
380 14.961
Sleeve part cannot be bent.
FT-PS1
FT-E22
FT-V10
2m
6.562 ft
1m
3.281 ft
FT-SFM2SV2
R25 mm
R0.984 in
FT-V22
"1 "0.039
0.66 0.024
0
"2.5 "0.098
40 1.575
1 0.039
0
"2 "0.079
Sleeve part cannot be bent.
30 1.181
FT-V41
120 4.724
Sleeve part cannot be bent.
"1 "0.039
80 3.150
2m
6.562 ft
R1 mm
R0.039 in
Note: Please take care that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut.
9
FT-WS4
FT-E12
2,350 92.520
1,000 39.370
FT-SNFM2
R5 mm
R0.197 in
"4 "0.157
3
0.118
FT-WS8
FT-P2
R4 mm
R0.157 in
Flexible
500 mm
19.685 in
19 0.748
6 0.236
FT-SFM2
2m
6.562 ft
650 25.591
260 10.236
Sleeve part cannot be bent.
Beam diameter
"0.25 mm "0.010 in
FT-WS3
R25 mm
R0.984 in
"2.5 "0.098
"1.5 "0.059
2m
6.562 ft
R1 mm
R0.039 in
2,400 94.488
760 29.921
"2.5 "0.098
"1.5 "0.059
600 23.622
Model No.
FT-WS8L
1,500 59.055
150 5.906
With lens • Long sensing range
"2.5 "0.098
"1.5 "0.059
Fiber cable Bending
length
Long sensing range type FX-102
: Free-cut radius
Sensing range (mm in)(Note)
FT-WV42
FX-100
LIST OF FIBERS
Pliable fibers (flexible and sharp bending fibers) are marked with light blue in the table.
Thru-beam type (one pair set)
Type
Shape of fiber head
(mm in)
Fiber cable Bending
length
Long sensing range type FX-102
: Free-cut radius
Sensing range (mm in)(Note 1)
Standard type FX-101
Easy mounting • Top sensing
W3H8D12
W0.118H0.315D0.472
Model No.
1,200 47.244
2,800 110.236
R1 mm
R0.039 in
FT-WZ8H
1,400 55.118
3,100 122.047
R4 mm
R0.157 in
Flexible
FT-Z8H
2,100 82.677
R1 mm
R0.039 in
FT-WZ8E
R4 mm
R0.157 in
Flexible
FT-Z8E
R1 mm
R0.039 in
FT-WZ8
R4 mm
R0.157 in
Flexible
FT-Z8
Easy mounting • Side sensing
700 27.559
W3H12D8
W0.118H0.472D0.315
800 31.496
1,850 72.835
2m
6.562 ft
Compact
Rectangular
Easy mounting • Front sensing
950 37.402
330 12.992
W8.5H12D3
W0.335H0.472D0.118
360 14.173
1,000 39.370
Front sensing
W10H7D2
W0.394H0.276D0.079
Fiber bending type
W2H10D10 W0.079H0.394D0.394
670 26.378
230 9.055
80 3.150
FT-WZ4
1m
3.281 ft
230 9.055
R1 mm
R0.039 in
Front sensing
W14H7D3.5
W0.551H0.276D0.138
Fiber bending type
W3.5H14D11 W0.138H0.551D0.433
330 12.992
580 22.835
190 7.480
"3.5
"0.138
"3.7
"0.146
Narrow beam
1,000 39.370
1,000 39.370
Side-view type with small light
dispersion
"4 "0.157
700 27.559
3
0.118
FT-WZ7
2m
6.562 ft
FT-WZ7HB
3,000 118.110
R25 mm
R0.984 in
2,200 86.614
R1 mm
R0.039 in
3,000 118.110
1,000 39.370
FT-WZ4HB
2m
6.562 ft
FT-K8
FT-WKV8
R25 mm
R0.984 in
FT-KV8
R10 mm
R0.394 in
FT-KV1
R1 mm
R0.039 in
FT-WA30
R10 mm
R0.394 in
FT-A30
R1 mm
R0.039 in
FT-WA8
R10 mm
R0.394 in
FT-A8
W2H1.5D20 W0.079H0.059D0.787
2 0.079
135 5.315
500 19.685
Sensing width
32 mm 1.260 in
Wide beam
Special
Wide area sensing
W5H69D20
W0.197H2.717D0.787
(Note
(No
ote 2)
3,500 137.795
(Note
(No
ote 2)
3,500 137.795
2m
6.562 ft
Wide area sensing
Sensingg width
11 mm 0.433in
1,500 59.055
(Note
(No
ote 2)
3,500 137.795
W4.2H31D13.5
W0.165H1.220D0.531
Array
Top sensing
W5H15D15 W0.197H0.591D0.591
280 11.024
Side sensing
W5H15D15
W0.197H0.591D0.591
240 9.449
FT-AFM2
720 28.346
670 26.378
2m
6.562 ft
R25 mm
R0.984 in
FT-AFM2E
Notes: 1) Please take care that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut.
2) The fiber cable length practically limits the sensing range to 3,500 mm 137.795 in long.
10
FX-100
LIST OF FIBERS
Thru-beam type (one pair set)
Type
Shape of fiber head
(mm in)
350 C 662 F
Lens mountable
Standard type FX-101
M4
350 C 662 F
Sleeve 60 mm 2.362 in
Heat-resistant
Fiber cable Bending
length
Long sensing range type FX-102
: Free-cut radius
Sensing range (mm in)(Note 1)
170 6.693
490 19.291
2m
6.562 ft
M4
"2.1 "0.083
Allows flexible wiring
200 C 392 F
Lens mountable
200 C 392 F
Lens mountable
M4
M4
130 C 266 F
Lens mountable (FX-LE2 only)
M4
100 3.937
300 11.811
540 21.260
210 8.268
250 9.843
700 27.559
1m
3.281 ft
1m
3.281 ft
R25 mm
R0.984 in
Model No.
FT-H35-M2
Fiber
R25 mm
R0.984 in
Sleeve
R10 mm
R0.394 in
FT-H35-M2S6
R10 mm
R0.394 in
FT-H20W-M1
FT-H20-M1
R25 mm
R0.984 in
2m
6.562 ft
FT-H13-FM2
200 mm 7.874 in
(Note 2)
FT-H20-J20-S
Special
Heat-resistant • Joint
Lens mountable (FX-LE1)
M4
Side-view
150 5.906
Easy mounting • Rectangular head
SEMI S2 compliant
W7H15D13
W0.276H0.591D0.512
500 19.685
520 20.472
"5.5 "0.217
Side-view
3,100 122.047
"5.5 "0.217
300 C 572 F
Lens mountable (FV-LE1/SV2 only)
M4
110 4.331
FT-H20-J30-S
Heatresistant
side fiber
R18 mm
R0.709 in
(Note 3)
800 31.496
280 11.024
(Note 4)
FT-H20-J50-S
(Note 4)
500 mm 19.685 in
(Note 2)
FT-H20-VJ50-S
800 mm 31.496 in
(Note 2)
FT-H20-VJ80-S
2m
6.562 ft
(Note 4)
(Note 4)
R25 mm
R0.984 in
FT-Z802Y
FT-L80Y
2,600 102.362
1,100 43.307
340 13.386
Vacuumresistant
300 mm 11.811 in
(Note 2)
500 mm 19.685 in
(Note 2)
"3.8
"0.150
"4
"0.157
Chemical-resistant
420 16.535
135 5.315
(Note 4)
2m
6.562 ft
(Note 5)
R30 mm
R1.181 in
1m
3.281 ft
R18 mm
R0.709 in
FT-V80Y
FT-H30-M1V-S
(Note 6)
Notes: 1) Please take care that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut.
2) This is the fiber length (fixed length) for heat-resistant side fibers. The ordinary-temperature side fibers are free-cut to 2 m 6.562 ft.
3) The ordinary-temperature side fiber is R25 mm R0.984 in or more.
4) Heat-resistant joint fibers and ordinary-temperature side fibers (FT-FM2) are sold as a set. Please refer to ‘Heat-resistant joint fiber catalog’ for details.
5) The allowable cutting range is 500 mm 19.685 in from the end that the amplifier inserted.
6) Sold as a set comprising vacuum-resistant type fiberphoto-terminal (FV-BR1)fiber at atmospheric side (FT-J8). Please refer to ‘Vacuum-resistant
fiber catalog’ for details.
Model No. when ordering heat-resistant joint fibers individually as replacement parts
• FT-H20-J20 (one pair set)
• FT-H20-VJ50 (one pair set)
• FT-H20-J30 (one pair set)
• FT-H20-VJ80 (one pair set)
• FT-H20-J50 (one pair set)
Model No. when ordering vacuum-resistant fibers individually as replacement parts
• Vacuum-resistant type fiber
FT-H30-M1V (one pair set)
11
• Photo-terminal
FV-BR1 (one pair set)
• Fiber at atmospheric side
FT-J8 (one pair set)
FX-100
LIST OF FIBERS
Pliable fibers (flexible and sharp bending fibers) are marked with light blue in the table.
Retroreflective type
Sharp bending
Shape of fiber head
(mm in)
Fiber cable Bending
length
Long sensing range type FX-102
: Free-cut radius
Sensing range (mm in)(Note 1, 2)
Standard type FX-101
W9.5H5.2D15 W0.374H0.205D0.591
100 to 550
3.937 to 21.654
W30H30D0.5 W1.181H1.181D0.020
W9.5H5.2D21 W0.374H0.205D0.827
100 to 830
3.937 to 32.677
2m
6.562 ft
R1 mm
R0.039 in
2m
6.562 ft
R10 mm
R0.394 in
2m
6.562 ft
R10 mm
R0.394 in
Model No.
FR-WKZ11
FR-KZ21
W10.6H28D10.1 W0.417H1.102D0.398
W9.5H25
D5.2
W0.374H0.984
D0.205
200 7.874
200 7.874
FR-KZ21E
W10.6H28D10.1
W0.417H1.102D0.398
W7.5H2.2D11.2 W0.295H0.087D0.441
Wafer mapping
Narrow beam
polarizing
p
Side sensing Top sensing With
filters
Type
15 to 200
0.591 to 7.874
15 to 360
0.591 to 14.173
FR-KV1
W4H2D21.5 W0.157H0.079D0.846
Notes: 1) Please take care that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut.
The sensing range of FR-WKZ11 is specified for the RF-13. The sensing range of FR-KZ21, FR-KZ21E and FR-KV1 is specified for the attached reflector.
The sensing ranges when using in combination with the FR-WKZ11 reflector (optional) are given in the below table.
Reflector
Amplifier
FX-101
FX-102
FR-WKZ11RF-210
100 to 700 3.937 to 27.559
100 to 1,100 3.937 to 43.307
FR-WKZ11RF-220
100 to 1,300 3.937 to 51.181
100 to 2,600 3.937 to 102.362
FR-WKZ11RF-230
100 to 2,000 3.937 to 78.740
100 to 4,000 3.937 to 157.480
2) The sensing range of FR-WKZ11 is the possible setting range for the reflector or reflective tape. The fiber can detect an object less than 100 mm 3.937 in away.
However, note that if there are any white or highly-reflective surfaces near the fiber head, reflected incident light may affect the fiber head. If this occurs,
adjust the threshold value of the amplifier unit before use.
The sensing range of FR-KZ21(E) is the possible setting range for the reflector. However, if setting the fiber to detect objects passing within 0 to 20 mm
0 to 0.787 in from the fiber head, unstable detection may result.
The sensing range of FR-KV1 is the possible setting range for the reflector. The fiber can detect an object less than 15 mm 0.591 in away.
Reflective type
Type
Shape of fiber head
(mm in)
M6
Fiber cable Bending
length
Long sensing range type FX-102
: Free-cut radius
Sensing range (mm in)(Note 1, 2)
Standard type FX-101
170 6.693
Coaxial
M6
FD-B8
440 17.323
R25 mm
R0.984 in
100 3.937
FD-FM2
410 16.142
Sleeve 90 mm 3.543 in
M6
M6
Threaded type
"2.5 "0.098
Sleeve 40 mm 1.575 in
M6
100 3.937
345 13.583
2m
6.562 ft
"2.5 "0.098
M6
80 3.150
90 3.543
230 9.055
200 7.874
M6
M6
70 2.756
220 8.661
Elbow
Tough flexible
M6
Model No.
70 2.756
180 7.087
1m
3.281 ft
2m
6.562 ft
Fiber
R25 mm
R0.984 in
Sleeve
R10 mm
R0.394 in
FD-FM2S
FD-FM2S4
R1 mm
R0.039 in
FD-W8
R4 mm
R0.157 in
Flexible
FD-P80
R10 mm
R0.394 in
FD-P81X
R25 mm
R0.984 in
FD-R80
Notes: 1) The sensing range is specified for white non-glossy paper (400400 mm 15.74815.748 in) as the object.
2) Please take care that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut.
12
FX-100
LIST OF FIBERS
Pliable fibers (flexible and sharp bending fibers) are marked with light blue in the table.
Reflective type
Type
Shape of fiber head
(mm in)
M4
Fiber cable Bending
length
Long sensing range type FX-102
: Free-cut radius
Sensing range (mm in)(Note 1, 2)
Standard type FX-101
110 4.331
FD-T80
345 13.583
R25 mm
R0.984 in
M4
FD-NFM2
Sleeve 90 mm 3.543 in
M4
35 1.378
Fiber
R25 mm
R0.984 in
Sleeve
R10 mm
R0.394 in
100 3.937
"1.48 "0.058
Sleeve 40 mm 1.575 in
M4
"1.48 "0.058
M4
Sleeve 40 mm 1.575 in
M4
15 0.591
40 1.575
2m
6.562 ft
"1.48 "0.058
M4
80 3.150
Small spot for sensing minute objects
Coaxial • Lens mountable
Threaded type
28 1.102
50 1.969
M4
230 9.055
75 2.953
120 4.724
150 5.906
45 1.772
M4
Small diameter
35 1.378
100 3.937
M3
M3
15 0.591
M3
8 0.315
Lens mountable (FX-MR3, FX-MR6)
M3
M3
Coaxial
Lens mountable (FX-MR3, FX-MR6)
M3
Tough flexible
Coaxial
Coaxial • Lens mountable (FX-MR3, FX-MR6)
M3
50 1.969
18 0.709
Coaxial • Lens mountable (FX-MR3, FX-MR6)
M3
Light emitting
fiber element 7 0.276
High precision "0.125 "0.005
"0.5 "0.020
Sleeve part cannot be bent.
Coaxial
"0.8 "0.031
M3
Sleeve part cannot be bent.
40 1.575
1 0.039
15 0.591
2m
6.562 ft
30 1.181
120 4.724
160 6.299
45 1.772
High precision
Coaxial • Lens mountable (FX-MR3, FX-MR6)
M3
Light emitting
fiber element 10 0.394
High precision "0.175 "0.007
M3
Model No.
1m
3.281 ft
(Note 3)
50 1.969
FD-NFM2S4
Fiber
R1 mm
R0.039 in
Sleeve
R10 mm
R0.394 in
FD-W44
R1 mm
R0.039 in
FD-WT8
R2 mm
R0.079 in
FD-WG4
R25 mm
R0.984 in
FD-G4
R4 mm
R0.157 in
Flexible
FD-P60
R25 mm
R0.984 in
FD-T40
R1 mm
R0.039 in
FD-WT4
R4 mm
R0.157 in
Flexible
FD-P40
R25 mm
R0.984 in
FD-G6
R10 mm
R0.394 in
FD-G6X
R25 mm
R0.984 in
FD-EG1
30 1.181
FD-EG2
500 mm
19.685 in
R10 mm
R0.394 in
22 0.866
FD-EG3
4 0.157
48 1.890
FD-NFM2S
FD-EN500S1
1m
3.281 ft
R25 mm
R0.984 in
FD-ENM1S1
Notes: 1) The sensing range is specified for white non-glossy paper [200200 mm 7.8747.874 in (FD-T80, FD-WT8: 400400 mm 15.74815.748 in, FD-W44,
FD-WT4, FD-P40, FD-G6, FD-EG1, FD-EG2, FD-EG3, FD-EN500S1, FD-ENM1S1: 100100 mm 3.9373.937 in)] as the object.
2) Please take care that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut.
3) The allowable cutting range is 700 mm 27.559 in from the end that the amplifier inserted.
13
FX-100
LIST OF FIBERS
Pliable fibers (flexible and sharp bending fibers) are marked with light blue in the table.
Reflective type
Shape of fiber head
(mm in)
Type
"3 "0.118
"3 "0.118
Fiber cable Bending
length
Long sensing range type FX-102
: Free-cut radius
Sensing range (mm in)(Note 1, 2)
Standard type FX-101
100 3.937
"3 "0.118
345 13.583
80 3.150
230 9.055
Coaxial
28 1.102
75 2.953
2m
6.562 ft
"3 "0.118
"1.5
"2.5
"0.059 "0.098
Ultra-small diameter
150 5.906
45 1.772
"2.5
"0.098
35 1.378
"1.5 "0.059
Side-view
Cylindrical type
"3 "0.118
25 0.984
"1.5 "
"0.5
"0.059 "0.020
Sleeve part cannot be bent.
Coaxial
"3 "0.118
"0.65 "0.026
Sleeve part cannot be bent.
Small diameter
"1.5 "0.059
0.77 0.028
0
"3 "0.118
Sleeve part cannot be bent.
"2
"
"3
"
"0.118 "0.079
1 0.039
0
Sleeve part cannot be
b bent.
"2
"
"5
"
"0.197 "0.079
0.88 0.031
0
Sleeve part cannot be
b bent.
Glass substrate detection • Mapping
3.5 0.138
65 2.559
2m
6.562 ft
1m
3.281 ft
13 0.512
1m
3.281 ft
16 0.630
25 0.984
6 0.236
30 1.181
16 to 30 0.630 to 1.181
W25H7.3D30 W0.984H0.287D1.181
Glass substrate detection • Alignment
W20H29D3.8
W0.787H1.142D0.150
100 3.937
0 to 40 0 to 1.575
45 1.772
70 2.756
20 0.787
2m
6.562 ft
90 3.543
12 to 50 0.472 to 1.969
0 to 50 0 to 1.969
4m
13.123 ft
3m
9.843 ft
Glass substrate detection • Alignment
Rectangular
Convergent reflective type
W17H29D3.8
W0669H1.142D0.150
Glass substrate detection •
Seating confirmation
W12H19D3
W0.472H0.748D0.118
Glass substrate detection
W24H21D4
W0.945H0.827D0.157
W6H18D14
W0.236H0.709D0.551
W7.2H7.5D2
W0.283H0.295D0.079
0 to 19 0 to 0.748
0 to 6 0 to 0.236
0 to 25 0 to 0.984
0 to 5.5 0 to 0.217
7 to 12 0.276 to 0.472
(Convergent point 8 0.315)
6 to 13.5 0.236 to 0.531
(Convergent point 8 0.315)
3 to 14 0.118 to 0.551
(Convergent point 8 0.315)
1.5 to 16 0.059 to 0.630
(Convergent point 8 0.315)
5 to 8 0.197 to 0.315
(Convergent point 6 0.236)
1 to 4.5 0.039 to 0.177
R25 mm
R0.984 in
FD-S80
R1 mm
R0.039 in
FD-WS8
R2 mm
R0.079 in
FD-WSG4
R4 mm
R0.157 in
Flexible
FD-P50
R25 mm
R0.984 in
FD-P2
R10 mm
R0.394 in
FD-E12
R25 mm
R0.984 in
FD-E22
R25 mm
R0.984 in
FD-V41
R1 mm
R0.039 in
FD-WV42
R25 mm
R0.984 in
FD-SFM2SV2
R25 mm
R0.984 in
FD-L46
FD-L45
R4 mm
R0.157 in
FD-L43
2m
6.562 ft
FD-L44
2m
6.562 ft
R10 mm
R0.394 in
FD-L44S
R1 mm
R0.039 in
2m
6.562 ft
1 to 17 0.039 to 0.669
(Convergent point 6 0.236)
0.5 to 6.5 0.020 to 0.256
FD-SNFM2
R4 mm
R0.157 in
Flexible
0 to 8 0 to 0.315
0 to 4.5 0 to 0.177
Model No.
FD-WL41
FD-L41
R10 mm
R0.394 in
FD-L4
1m
3.281 ft
R1 mm
R0.039 in
FD-WL48
Notes: 1) The sensing range is specified for white non-glossy paper (FD-S80, FD-WS8: 400400 mm 15.74815.748 in, FD-WSG4, FD-P50, FD-SNFM2,
FD-V41, FD-SFM2SV2: 200200 mm 7.8747.874 in, FD-P2, FD-E12, FD-E22, FD-WV42, FD-L4, FD-WL48: 100100 mm 3.9373.937 in, FD-L46:
100100t 0.7 mm 3.9373.937t 0.028 in R edge of LCD glass substrates, FD-L43, FD-L44
4 and FD-L45: 100100t 0.7 mm 3.9373.937t 0.028 in
LCD glass substrates, FD-L44S: silicon wafers polished surface, FD-WL41, FD-L41: 100100t 2 mm 3.9373.937t 0.079 in glass substrates)
2) Please take care that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut.
14
FX-100
LIST OF FIBERS
Pliable fibers (flexible and sharp bending fibers) are marked with light blue in the table.
Reflective type
Type
Shape of fiber head
(mm in)
Fiber cable Bending
length
Long sensing range type FX-102
: Free-cut radius
Sensing range (mm in)(Note 1, 2)
Standard type FX-101
Model No.
Front sensing
Compact
Array
Liquid level sensing
Special
sensing
Wide beam Long
range
g
Rectangular
W10H7D2
W0.394H0.276D0.079
Fiber bending type
Front sensing
FD-WZ4
2 to 20 0.079 to 0.787
1 to 70 0.039 to 2.756
1m
3.281 ft
W2H D10
W0.079H0.394D0.394
W14H7D3.5
W0.551H0.276D0.138
Fiber bending type
W3.5H14D11
W0.138H0.551D0.433
Long sensing range • Rectangular head
W5.2 5D15
W0.205H0.374D0.591
R1 mm
R0.039 in
1 to 55 0.039 to 2.165
1 to 60 0.039 to 2.362
20 to 180 0.787 to 7.087
125 4.921
160 6.299
FD-WZ7
0.5 to 180 0.020 to 7.087
20 to 480
0.787 to 18.898
250 9.843
W7H15D30 W0.276H0.591D1.181
Top sensing
W5 H20D20
W0.197H0.787D0.787
Side sensing
W5 H20D20
W0.197H0.787D0.787
Contact type
"6 "0.236
Mountable on pipe •
Standard
W25H13D20
W0.984H0.512D0.787
Mountable on pipe • For PFA, wall
thickness 1 mm 0.039 in pipe
W25H13D20
W0.984H0.512D0.787
105 4.134
85 3.346
FD-WZ4HB
2m
6.562 ft
FD-WZ7HB
2m
6.562 ft
2m
6.562 ft
R1 mm
R0.039 in
R25 mm
R0.984 in
285 11.220
245 9.646
Applicable pipe diameter:
Outer dia. "6 to "26 mm "0.236 to "1.024 in transparent pipe
[PFA (fluorine resin) or equivalently transparent pipe, wall thickness 1 mm 0.039 in]
FD-A15
FD-AFM2
2m
6.562 ft
2m
6.562 ft
(Note 3)
Applicable pipe diameter:
Outer dia. "6 to "26 mm "0.236 to "1.024 in transparent pipe
[PVC (vinyl chloride), fluorine resin, polycarbonate, acrylic, glass, wall thickness 1 to 3 mm 0.039 to 0.118 in]
FD-WKZ1
R25 mm
R0.984 in
FD-AFM2E
Protective tube
R40 mm
R1.575 in
Fiber
R15 mm
R0.591 in
FD-F8Y
FD-F41
2m
6.562 ft
R10 mm
R0.394 in
FD-F4
Notes: 1) The sensing range is specified for white non-glossy paper [200200 mm 7.8747.874 in (FD-WKZ1, FD-AFM2, FD-AFM2E: 400400 mm 15.47815.478 in)]
as the object.
2) Please take care that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut.
3) The allowable cutting range is 1,000 mm 39.370 in from the end that the amplifier inserted.
15
FX-100
LIST OF FIBERS
Reflective type
Type
Shape of fiber head
(mm in)
Fiber cable Bending
length
Long sensing range type FX-102
: Free-cut radius
Sensing range (mm in)(Note 1, 2)
Standard type FX-101
350 C 662 F • Coaxial
M6
350 C 662 F • Sleeve 60 mm 2.362 in
"2.8
"
M6
"0.110
200 C 392 F • Coaxial
M6
75 2.953
2m
6.562 ft
280 11.024
120 4.724
Heat-resistant
Special
350 C 662 F • Sleeve 90 mm 3.543 in
"2.1
"
"0.083
200 C 392 F • Coaxial
1m
3.281 ft
200 7.874
M4
90 3.543
Fiber
R25 mm R0.984 in
Sleeve
R10 mm
R0.394 in
FD-H35-M2S6
Fiber
R25 mm R0.984 in
Sleeve
R10 mm
R0.394 in
FD-H35-20S
FD-H20-21
280 11.024
M4
300 C 572 F • Glass substrate detection
Convergent reflective type
W19H27D5
W0.748H1.063
D0.197
2 to 9 0.079 to 0.354
180 C 356 F • Glass substrate detection
Convergent reflective type
y
W19H27D5
W0.748H1.063
D0.197
130 C 266 F
M6
Vacuum-resistant
R25 mm
FD-H35-M2
R0.984 in
R25 mm
FD-H20-M1
R0.984 in
300 11.811
85 3.346
Model No.
0 to 10 0 to 0.394
2m
6.562 ft
0 to 17 0 to 0.669
FD-H30-L32
R25 mm
R0.984 in
0 to 25 0 to 0.984
100 3.937
FD-H18-L31
2m
6.562 ft
280 11.024
FD-H13-FM2
300 C 572 F • Rectangular head
W9.5H5.2D15 W0.374H0.205D0.591
300 C 572 F • Glass substrate detection
Convergent reflective type
W19H5D27
W0.748H0.197
D1.063
25 to 80 0.984 to 3.150
2.5 to 6.5 0.098 to 0.256
10 to 220 0.394 to 8.661
1m
3.281 ft
3m
9.843 ft
0 to 11 0 to 0.433
R18 mm
R0.709 in
FD-H30-KZ1V-S
(Note 3)
FD-H30-L32V-S
(Note 3)
Notes: 1) The sensing range is specified for white non-glossy paper [400400 mm 15.74815.748 in (FD-H30-L32, FD-H18-L31: 5050 mm 1.9691.969 in
glass substrate, FD-H30-KZ1V-S, FD-H30-L32V-S: 100100t 0.7 mm 3.9373.937t 0.028 in transparent glass)] as the object.
2) Please take care that the sensing range of the free-cut type fiber may be reduced by 20 % max. depending upon how the fiber is cut.
3) Sold as a set comprising vacuum-resistant type fiberphoto-terminal (FV-BR1)fiber at atmospheric side (FT-J8).
Model No. when ordering vacuum-resistant fibers individually as replacement parts
• Vacuum-resistant type fiber
FD-H30-KZ1V
FD-H30-L32V
• Mounting bracket for FD-H30-KZ1V
MS-FD-2
• Photo-terminal
FV-BR1 (one pair set)
• Fiber at atmospheric side
FT-J8 (one pair set)
Accessories (attached with fibers)
RF-003 (FR-KZ21/KZ21E exclusive reflector)
• RF-003
RF-13 (Reflective tape)
FX-CT1 (Fiber cutter)
FX-CT2 (Fiber cutter)
FX-AT2 (Attachment for fixed-length fiber, Orange)
FX-AT3 (Attachment for "2.2 mm "0.087 in fiber, Clear orange)
FX-AT4 (Attachment for "1 mm "0.039 in fiber, Black)
FX-AT5 (Attachment for "1.3 mm "0.051 in fiber, Gray)
FX-AT6 (Attachment for "1 mm "0.039 in / "1.3 mm "0.051 in mixed fiber, Black / Gray)
If connecting to a fiber amplifier other than the
FX-100 series
Applicable fiber amplifiers: FX2 / FX3 series
FX-AT10 (Attachment for "1 mm "0.039 in fiber)
FX-AT13 (Attachment for "1.3 mm "0.051 in fiber)
FX-AT15 (Attachment for "1 mm "0.039 in / "1.3 mm "0.051 in mixed fiber)
• RF-13
• FX-CT1
• FX-CT2
• FX-AT2
• FX-AT3
• FX-AT4
• FX-AT10
• FX-AT13
• FX-AT15
• FX-AT5
• FX-AT6
16
FX-100
FIBER OPTIONS
Lens (For thru-beam type fiber)
Designation
Model No.
Description
Increases the sensing
range by 5 times or more.
For thru-beam type fiber
Expansion
lens
(Note 1)
• Ambient temperature:
60 to 350 °C
76 to 662 °F
FX-LE1
Tremendously increases the
sensing range with large
diameter lenses.
Superexpansion
lens
(Note 1)
FX-LE2
Side-view
lens
Side-view
lens for
vacuumresistant fiber
FV-LE1
FX-SV2
Amplifier
Fiber
FX-101
FX-102
FT-B8
FT-FM2, FT-T80
FT-R80
FT-W8
FT-P80, FT-P60
FT-P81X
FT-H35-M2
FT-H20W-M1
FT-H20-M1
FT-H20-J20-S,, FT-H20-J30-S,, FT-H20-J50-S
2,200
3,000
1,900
3,000
3,500 (Note 2)
1,600 (Note 2)
2,000
1,300
1,600 (Note 2)
1,000
3,500 (Note 2)
3,500 (Note 2)
3,500 (Note 2)
3,500 (Note 2)
3,500 (Note 2)
1,600 (Note 2)
3,500 (Note 2)
1,600 (Note 2)
1,600 (Note 2)
3,500 (Note 2)
Sensing range (mm) [Lens on both sides]
Amplifier
Fiber
FX-101
FX-102
• Ambient temperature:
60 to 350 °C
76 to 662 °F
FT-B8,, FT-FM2,, FT-R80,, FT-W8,, FT-P80,, FT-P60
FT-P81X
FT-H35-M2
FT-H20W-M1, FT-H20-M1
FT-H13-FM2
FT-H20-J20-S,, FT-H20-J30-S,, FT-H20-J50-S
3,500 (Note 2)
1,600 (Note 2)
3,500 (Note 2)
1,600 (Note 2)
3,500 (Note 2)
3,500 (Note 2)
3,500 (Note 2)
1,600 (Note 2)
3,500 (Note 2)
1,600 (Note 2)
3,500 (Note 2)
3,500 (Note 2)
Beam axis is bent by 90 °.
Sensing range (mm) [Lens on both sides]
• Ambient temperature:
60 to 300 °C
76 to 572 °F
Fiber
Sensing range increases by
4 times or more.
• Ambient temperature:
40 to 120 °C 40 to248 °F
Beam axis is bent by 90 °.
Sensing range (mm) [Lens on both sides] (Note 3)
FX-SV1
Expansion
lens for vacuumresistant fiber
(Note 1)
Sensing range (mm) [Lens on both sides]
Amplifier
FT-B8
FT-FM2, FT-T80
FT-W8
FT-P80
FT-P60
FT-P81X
FT-H35-M2
FT-H20W-M1
FT-H20-M1
FT-H20-J20-S,, FT-H20-J30-S,, FT-H20-J50-S
Amplifier
Fiber
FT-H30-M1V
FX-101
FX-102
530
550
450
420
300
550
280
140
280
150
1,450
1,700
1,300
1,400
850
1,700
800
400
840
410
FX-101
FX-102
450
1,600
,
Sensing range (mm) [Lens on both sides] (Note 3)
• Ambient temperature:
Fiber
60 to 300 °C 140 to572 °F FT-H30-M1V
Amplifier
FX-101
FX-102
450
1,600
,
Notes: 1) Be careful when installing the thru-beam type fiber equipped with the expansion lens, as the beam envelope becomes narrow and alignment is difficult. Especially
when installing a fiber with many cores (sharp bending fibers and heat-resistant glass fiber), please be sure to use it only after you have adjusted it sufficiently.
2) The fiber cable length practically limits the sensing range to 3,500 mm 137.795 in long (FT-H20W-M1, FT-P81X
X and FT-H20-M1: 1,600 mm 62.992 in).
3) The fiber cable length for the FT-H30-M1V
V is 1m 3.281 ft. The sensing ranges in FX-102 (long sensing range type) take into account the length of the FT-J8 atmospheric side fiber.
Lens (For reflective type fiber)
Designation
Model No.
Pinpoint spot
lens
Description
Pinpoint spot of "0.5 mm "0.020 in. Enables detection of minute objects or small marks.
• Distance to focal point: 61 mm 0.236 0.039 in
• Applicable fibers: FD-WG4, FD-G4
• Ambient temperature:40 to70 °C 40 to158 °F
FX-MR1
Screw-in
depth
FX-MR2
Zoom lens
For reflective type fiber
Distance to
focal point
Finest spot
lens
Spot
diameter
FX-MR3
Distance to
focal point
Finest spot
lens
Spot diameter
FX-MR6
Screw-in depth
Zoom lens
Side-view
type
(
)
FX-MR5
Distance
nce
to foca
al
point
Spot diameter
The spot diameter is adjustable from "0.7 mm
to "2 mm "0.028 in to "0.079 in according to
how much the fiber is screwed in.
• Applicable fibers: FD-WG4, FD-G4
• Ambient temperature:40 to70 °C 40 to158 °F
• Accessory: MS-EX-3 (mounting bracket)
Extremely fine spot of "0.3 mm "0.012 in
approx. achieved.
• Applicable fibers: FD-WG4, FD-G4,
FD-EG1, FD-EG2, FD-EG3, FD-G6X, FD-G6
• Ambient temperature:
40 to70 °C 40 to158 °F
Extremely fine spot of "0.1 mm "0.004 in
approx. achieved.
• Applicable fibers: FD-WG4, FD-G4,
FD-EG1, FD-EG2, FD-EG3, FD-G6X, FD-G6
• Ambient temperature:
20 to60 °C 4 to140 °F
Sensing range for FX-101 (Note)
Screw-in depth
7 mm
12 mm
14 mm
Distance to focal point
18.5 mm approx.
27 mm approx.
43 mm approx
Spot diameter
"0.7 mm
"1.2 mm
"2.0 mm
Sensing range for FX-101 (Note)
Fiber model No. Distance to focal point
FD-EG3
7.50.5 mm
FD-EG2
7.50.5 mm
FD-EG1
7.50.5 mm
FD-WG4/G4/G6X/G6
7.50.5 mm
Spot diameter
"0.15 mm approx.
"0.2 mm approx.
"0.3 mm approx.
"0.5 mm approx.
Sensing range for FX-101 (Note)
Fiber model No. Distance to focal point
FD-EG3
7.50.5 mm
FD-EG2
7.50.5 mm
FD-EG1
7.50.5 mm
FD-WG4/G4/G6X/G6
7.50.5 mm
Spot diameter
"0.1 mm approx.
"0.15 mm approx.
"0.2 mm approx.
"0.4 mm approx.
FX-MR2 is converted into a side-view type Sensing range for FX-101 (Note)
and can be mounted in a very small space. Screw-in depth Distance to focal point Spot diameter
• Applicable fibers: FD-WG4, FD-G4
8 mm
13 mm approx.
"0.5 mm
• Ambient temperature:
10 mm
15 mm approx.
"0.8 mm
40 to70 °C 40 to158 °F
14 mm
30 mm approx
"3.0 mm
Note: The sensing ranges are the values when used in combination with FX-101 (standard type). Please contact our office for details on sensing ranges for other types of amplifier.
17
FX-100
FIBER OPTIONS
Others
Model No.
FTP-500 (0.5 m 1.640 ft)
FTP-1000 (1 m 3.281 ft)
Protective tube
For thru-beam
type fiber
(
)
FTP-1500 (1.5 m 4.921 ft)
FTP-N500 (0.5 m 1.640 ft)
FTP-N1000 (1 m 3.281 ft)
FTP-N1500 (1.5 m 4.921 ft)
FDP-500 (0.5 m 1.640 ft)
FDP-1000 (1 m 3.281 ft)
Protective tube
For reflective
type fiber
(
)
FDP-1500 (1.5 m 4.921 ft)
FDP-N500 (0.5 m 1.640 ft)
FDP-N1000 (1 m 3.281 ft)
FDP-N1500 (1.5 m 4.921 ft)
Fiber bender
FB-1
Universal sensor MS-AJ1-F
mounting stand
(Note 2)
MS-AJ2-F
Protective tube
Description
For
M4
thread
FT-B8
FT-P80
FT-FM2
FT-P60
FT-FM2S FT-FM2S4
FT-H13-FM2
For
M3
thread
FT-T80
FT-P40
FT-NFM2 FD-T40
FT-NFM2S FD-P40
FT-NFM2S4
For
M6
thread
Applicable fibers
Designation
FD-B8
FD-FM2
FD-FM2S
FD-FM2S4
• FTP-
• FDP-
Fiber bender
• FB-1
The protective tube, made
of non-corrosive stainless
steel, protects the inner
FD-P80 fiber cable from any
FT-H13-FM2 external forces.
FD-T80
FD-NFM2
FD-NFM2S
FD-NFM2S4
For
M4
thread
Fiber cutter
• FX-CT2
• FX-CT1
The fiber bender bends the sleeve part of the fiber head at the
proper radius. (Note 1)
Horizontal mounting type
Vertical mounting type
Mounting stand assembly for fiber
(For M3, M4 or M6 threaded head fiber)
Universal sensor mounting stand
FX-CT2
Fiber cutter
FX-CT1
Attachment for
fixed-length fiber
FX-AT2
The free-cut type fiber can be easily cut.
Accessory. FX-CT1 is attached with the FT-P80 or the FD-P80.
The FX-CT2 is provided with fibers other than this.
Using the arm which enables adjustment in
the horizontal direction, sensing can also
be done from above an assembly line.
• MS-AJ1-F
360 ° rotation
Forward / back
adjustment: 130 mm
5.118 in approx.
This is the attachment for the fixed length fiber. Orange.
(Accessory)
Attachment for "2.2 mm
FX-AT3
"0.087 in fiber
This is the attachment for the "2.2 mm "0.087 in fiber. Clear Orange.
(Accessory. Does not attach with the FT-P80 or the FD-P80.)
Attachment for "1 mm
FX-AT4
"0.039 in fiber
This is the attachment for the "1 mm "0.039 in fiber. Black.
(Accessory)
Attachment for "1.3 mm
FX-AT5
"0.051 in fiber
This is the attachment for the "1.3 mm "0.051 in fiber. Gray.
(Accessory)
Attachment for "1 mm
"0.039 in / "1.3 mm FX-AT6
"0.051 in mixed fiber
This is the attachment for the "1 mm "0.039 in / "1.3 mm "0.051 in
mixed fiber. Black / Gray. (Accessory)
Height
adjustment:
150 mm
5.906 in
approx.
360 °
rotation
2 °
20
Mounting hole
20 °
for M6 screw
Angle adjustment:20 °
• MS-AJ2-F
360 ° rotation
Forward / back
adjustment: 130 mm
5.118 in approx.
Height
adjustment:
150 mm
5.906 in
approx.
Notes: 1) Do not bend the sleeve part of any side-view type fiber or ultra-small diameter head type fiber.
2) Refer to the ‘Sensor general catalog 2003-2004’ or the SUNX website: http://www.sunx.jp/ for universal sensor mounting stand.
360 °
rotation
Mounting hole
2 °
20
for M6 screw
20 °
Angle adjustment:20 °
Fiber attachment
It’s possible to simultaneously cut two fibers to the same length
Each fiber (with some exceptions) has a newly developed two-in-one fiber attachment (FX-AT3/AT4/AT5/AT6) which enables two fibers to be
cut simultaneously to the same length with the new fiber cutter (FX-CT2). Also, since the fibers can be attached to the amplifier while being
fixed in position in the two-in-one fiber attachment, sensitivity changes resulting from variation in the amount of fiber insertion do not occur.
• FX-AT2
For fixed-length
fiber
• FX-AT3
For "2.2 mm
"0.087 in fiber
• FX-AT4
For "1 mm
"0.039 in fiber
• FX-AT5
For "1.3 mm
"0.051 in fiber
• FX-AT6
For "1 mm "0.039 in /
"1.3 mm "0.051 in mixed fiber
PRECAUTIONS FOR PROPER USE
• Never use this product as a sensing device for personnel protection.
• In case of using sensing devices for personnel protection, use products
which meet regulations and standards, such as OSHA, ANSI or IEC
etc., for personnel protection applicable in each region or country.
Part description
Operation indicator
(Orange)
Digital display (Green)
(Threshold value)
ON key /
Set value UP key
OFF key /
Set value DOWN key
MODE key
Digital display (Red)
(Incident light intensity)
18
䡵DIMENSIONS (Unit: mm in)
The CAD data in the dimensions can be downloaded from the website: http://www.sunx.jp/
FX-101䡺, FX-102䡺
0.8
0.031
Amplifier
47 1.850
29 1.142
20
12.2
0.787
7
0.480
FX-101(P)-Z, FX-102(P)-Z
6 0.236 6 0.236
2.7
0.106
0
0.7
0.028
OFF key / Setting value DOWN key
ON key / Setting value UP key
4.1
Operation indicator (Orange) 0.161
Digital display (Green, Red)
MODE key
Assembly dimensions with optional protective cover
0.75 0.030
6 6 10.85
0.236 0.236 0.427
47 1.850
1 850
29 1.142
1 142
12.2
0.8
0.480
0.031
0
Amplifier
0.7 0.028
Operation indicator (Orange) 4.1
0.161
Digital display (Green, Red)
9
0.354
2.7
0.106
OFF key / Setting value DOWN key
ON key / Setting value UP key
MODE key
1
0.039
1.1
0.043
7
0.276
9
0.354
66.2
2.606
2 0.079
2 0.079
7 6 0.236
0.276
1.1
0.043
0.8
0.031
30
10
0.394 1.181
8.1
0.319
3 0.118
10
0.394
"3.2
"0.126
4
0.157
5.5 0.217
MS-DIN-4
5.5
0.217
"6.2 mm "0.244 in
spot facing, 3 0.118 deep
5
0.197
Material: PBT
35 1.378
1 378
64.5 2.539
3.2
0.126
End plate (Optional)
7.2 mm 0.283 in
spot facing, 4 0.157 deep
2.75 0.108
3
0.118
15
0.591
1
0.039
15
0.591
M3 (Iength 18 mm 0.709 in) pan head screws
60
2.362
6.2 mm 0.244 in
spot facing, 3 0.118 deep
3.2
0.126
"3.2 "0.126
3 0.118
1.6
0.063
32
1.260
4
0.157
Suitable for 35mm 1.378 in width DIN rail
Material: Polycarbonate
CN-14A-C䡺
(8)
5.6 M3 Square nut
0.220
24.7
0.972
9
0.354
1
0.039
24.5
0.965
35
1.378
35
(1.378
1 378 )
Suitable for 35 mm 1.378 in width DIN rail
MS-DIN-E
11.5
0.453
4
0.157
13.5
0.531
Suitable for 35 mm 1.378 in width DIN rail
"3.2 "0.126
9.25
0.364
3.2
8.1
0.126 0.319
2
0
0.079
3
0.118
50 1.969
2
0.0
079
Amplifer mounting bracket (Optional)
"7.2 mm "0.283 in
spot
p facing,
g 4 0.157 deep
p
10 30
.18
0.3941.181
"3.2
"0.126
3.2
0
0.126
50 1.969
35 1.378
64.5 2.539
13.5
0.531
10
0.394
"6.5
"0.256
4
0.157
Connector attached cable (Optional)
L
CN-14A-C2 is attached FX-101(P)-CC2 / FX-102(P)-CC2
50
(1.969
1 969)
• Length L
(8)
"3.7 "0.146 cable
Model No.
CN-14A-C1
CN-14A-C2
CN-14A-C3
CN-14A-C5
Length L (mm in)
1,000 39.370
2,000 78.740
3,000 118.110
5,000 196.850
All information is subject to change without prior notice.
SUNX Limited
2431-1 Ushiyama-cho, Kasugai-shi, Aichi,
486-0901, Japan
Phone: +81-(0)568-33-7211
FAX: +81-(0)568-33-2631
Overseas Sales Dept.
http://www.sunx.jp/
Phone: +81-(0)568-33-7861
FAX: +81-(0)568-33-8591
Printed on 100% recycled paper
PRINTED IN JAPAN
No.CE-FX100-10 January, 2007
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement