Mounts by PDM 625T-11 PANEL DISPLAY MOUNT

Mounts by PDM 625T-11  PANEL DISPLAY MOUNT
Mounts by
A division of David Engineering & Mfg. Inc.
Model
PDM 625T-11 PANEL DISPLAY MOUNT
Thank you for purchasing the PDR panel display wall mount.
To ensure the correct usage, please read and follow the instructionsmanual thoroughly. Please store the instructions in a safe place for future reference.
All PDR mounts and adapters carry a limited lifetime warranty against defects in material and workmanship.
We are not liable for improper installation that results in damage to mounts, adapters or presentation equipment.
Special techniques are necessary for installation of the panel display mount.
Do not attempt to perform this work by yourself.
Request an installation specialist to install this unit.
Manufacturer assumes absolutely no responsibility for injuries and damages that may occur due to improper installation and handling.
Please remember that if you remove the panel display from the wall later, you will find the screw holes and anchor bolts for the
mounting unit left on the wall. Also note that long use of the panel display may discolor the wall around it due to its heat and
airflow.
To ensure customer safety, be sure to decide the installation location so that the strength is sufficient to withstand the weightof both the panel
display and the wall mount.
Always use at least two persons for all installations.
Fully tighten all of the mounting screws as specified in the installation instructions.
Parts Configuration Chart
Features
Low profile 2 5/8”
16”, 24” or 32” stud mounting points
Easy installation
Flat to 12º tilt (no tools required)
Lateral movement from center for better viewing position
1
INSTALLATION LOCATION
WARNING
The wall where the wall mount is to be installed must be capable of long-term support of the total load of
the panel display and wall mount. Measures should al so be taken to ensure sufficient strength to
withstand the force of earthquakes, vi bration and other external forces.
Note: Incorrect installation can cause the p anel display to fall and cause injury.
Total load of the panel (p anel display + wall mount)
MAXIMUM WEIGHT 300 LBS (92 kg)
INSTALLATION ON A WOODEN WALL
Always install so that the load is supported by a wood stud. If the strength of the wood studs is not sufficient, add reinforcement.
Do not install on decorative posts or plaster board.
Always confirm the center of the stud is used for the installation.
CAUTION
Avoid installing in locations where the temperature and humidity are excessively high, and where contact with any
water is possible. These can result in fire or electric shock.
Do not install close to an air conditioner intake or outlet. Do not install in locations where there are excessive amounts of d ust,
oily smoke or tobacco smoke. Fire could result.
Do not block the ventilation holes. Leave sufficient clearance in regard to the surroundings to avoid blocking the ventilation.
.
The internal temperature could elevate and possibly result in fire. Install the panel (4") or more away from surroundings.
. on a vertical surface. Avoid sloped surfaces. Also, do not install facing upward. The internal temperature could
Install only
elevate and possibly result in fire. Injury or damage could also result from falling.
Do not install in locations where there is excessive vibration or impact. Injury and damage could result from the panel display
falling.
Do not install where there is direct sunlight or other strong light. Strong light could result in eye fatigue during usage.
WARNING
Use the specified bolts and screws in the specified places and tighten firmly. Failure to do this could cause injury if the panel
display falls.
Do not alter any of the parts. Do not use broken parts. This could result with injury due to the panel display falling.
Make sure that both hooks from the each pivot bracket engage with the wall bracket . Failure to do so could cause the panel
display to fall.
Always use at least two people to perform the installation work. Injury could result from dropping heavy objects.
Caution: Installation of unit is to be carried out by qualified technicians only. Install in an appropriate location by checking the wall structure
and durability for safety and accident prevention.
Rev 021908
2
PARTS LIST
A
Display bracket .... 2 pcs
B
Wall mount bracket…1 pc
C
Locking bar... 2 pc
D
I
5/16” Flat washers...6 pcs Plastic spacer 3/4 x 1”...4 pcs
J
E
5/16’ x 2 ½”Lag bolts...6 pcs Multi mount washer ...4 pcs
K
F
5mm x 40mm... 4 pcs
5mm x 16mm...4 pcs
L
G
6mm x 40mm...4pcs
6mm x 16mm...4 pcs
H
M
8mm x 16mm...4pcs
8mm x 40mm...4pcs
MOUNTING ARM ASSEMBLY
Fig 1
TOP
BOTTOM
LEFT HAND SHOWN RIGHT HAND OPPOSITE
3
1. FASTEN MOUNTING PLATE TO WALL
The bracket must be secured to the wall studs capable of at least (4) times the weight of the unit. The wall bracket should be mounted at the same horizontal center line
as the display center line ( viewing horizontal center line). Using the six lag bolts( E ) and washers supplied ( D ), level and secure the mounting plate to the center of
the wall studs. Pre drill 3/16” (5mm) hole for lag bolts Fig.2
Fig 2
47 ½”
4”
EQUAL
SPACING
VIEWING
HORIZONTAL
CENTER LINE
WOOD STUDS
(std construction 2 x 4 studs/1/2” wallboard)
16"
32"
FLOOR LINE
2. SECURE THE DISPLAY BRACKETS TO THE MONITOR
Lay the display panel face down on a protected surface. Position the left and the right hand brackets ( A ) with the slots facing towards the top.
See Fig.3. Note bottom edge! Using the proper screws and square multi-mount washers supplied, position the brackets equal distance from
top to bottom and tighten hardware.
NOTE: Do not over tighten the bracket mounting screws as damage to the display internal mounting threads could occur.
Fig 3
Square Multi-mount washer (J )
Mounting hardware F,G,H,K,L,M
Display bracket ( A ) right
Display bracket ( A ) left
Plastic spacer ( I )
Panel display bottom edge
4
3. MOUNT THE DISPLAY TO THE WALL MOUNT BRACKET
Lift the display, with the brackets attached, onto the wall plate. See Fig4 Position the top and bottom into the slots. See Fig 5 and Fig 6
Insert the locking bars (C) as shown in Fig 5 with the locking holes facing up to match the holes in the wall mount bracket (B) . Make sure the display brackets
engage the rails on the wall mount bracket (B)
See Fig 5. Secure with a padlock (not supplied) if required thru holes in the locking bars (C) and wall mount bracket (B)Fig 5
Fig 5
Fig 4
Locking bars (C)
4. Adjust lateral movement
Lateral Movement:
Once the display on the wall is complete, you can still move the display left to right to optimize the final viewing position by gently sliding the unit on the wall
bracket. The adjustment distance will vary depending on the display model being installed. See Fig 7
Adjust for best viewing angle (up to 12 deg.) using the Tri knob.
After adjustment is complete, tighten both tri knobs . See Fig 6
Fig 6
12°
Fig 7
Tri knob
5
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement