MAX9632EVKIT
MAX9632 Evaluation Kit
Evaluates: MAX9632
General Description
The MAX9632 evaluation kit (EV kit) provides a proven
design to evaluate the MAX9632 low-noise, precision
and wide-band op amp. The MAX9632 can be used in a
wide variety of applications such as test and measurement, instrumentation, medical imaging, control loops,
and professional audio. Because of the ultra-low noise
and great precision, it can either drive high-resolution
(18 to 24 bits) ADCs or buffer high-resolution DACs. The
EV kit circuit can easily be adapted by installing shunts
and changing a few components to support multiple
op-amp configurations: transimpedance, noninverting,
inverting, or differential amplifier. The components on
the EV kit have pads that accommodate 0805 packages,
making them easy to solder and replace. The EV kit
accepts a single-supply voltage from +4.5V to +36V or a
dual-supply voltage from Q2.25V to Q18V.
Features
S Accommodates Multiple Op-Amp Configurations
S +4.5V to +36V Wide Input Supply Range
S Shutdown Input
S 0805 Components
S Proven PCB Layout
S Fully Assembled and Tested
Ordering Information
PART
TYPE
MAX9632EVKIT+
EV Kit
+Denotes lead(Pb)-free and RoHS compliant.
Component List
DESIGNATION
C1, C3
QTY
2
DESCRIPTION
QTY
JU3
1
3-pin header
R1
0
Not installed, resistor (0805)
R2, R4
2
100I Q1% resistors (0805)
R3, R5
2
0I resistors (0805)
U1
1
Single high-voltage op amp
(8 TDFN)
Maxim MAX9632ATA+
—
3
Shunts
—
1
PCB: MAX9632 EVALUATION
KIT+
0.1FF Q10%, 50V X7R ceramic
capacitors (0805)
Murata GRM21BR71H104K
TDK C2012X7R1H104K
2
4.7FF Q10%, 50V X5R ceramic
capacitors (1210)
Murata GRM32ER71H475M
TDK C3225X7R1H475M
C5, C6, C7
0
Not installed, ceramic capacitors
(0805)
JU1, JU2
2
2-pin headers
C2, C4
DESIGNATION
DESCRIPTION
Component Suppliers
SUPPLIER
Murata Electronics North America, Inc.
PHONE
770-436-1300
WEBSITE
www.murata-northamerica.com
TDK Corp.
847-803-6100
www.component.tdk.com
Note: Indicate that you are using the MAX9632 when contacting these component suppliers.
For pricing, delivery, and ordering information, please contact Maxim Direct
at 1-888-629-4642, or visit Maxim’s website at www.maximintegrated.com.
19-5592; Rev 1; 2/14
MAX9632 Evaluation Kit
Evaluates: MAX9632
Quick Start
• MAX9632 EV kit
Required Equipment
• ±15V, 40mA DC power supply (PS1)
• +1V precision voltage source
• Digital multimeter (DMM)
Procedure
The EV kit is fully assembled and tested. Follow the steps
below to verify board operation:
1) Connect the positive terminal of the +15V supply to
the VCC pad and the GND terminal to the GND pad.
Connect the negative terminal of the -15V supply to
the VEE pad and the GND terminal to the GND pad.
The power supplies should be off.
2) Connect the positive terminal of the precision voltage
source to the IN- pad. Connect the negative terminal
of the precision voltage source to the IN+ pad.
3) Install a shunt on jumper JU2 to short IN+ to GND.
4) With the 100I feedback resistor and on-board 100I
resistor, the gain is -1 (inverting configuration).
5) Connect the DMM to monitor the voltage on the OUT
pad.
6) Turn on the Q15V power supply.
7) Apply 1V from the precision voltage source. Observe
the output at the OUT pad on the DMM. OUT should
read approximately -1V.
Jumper Selection
Jumpers JU1 and JU2 are provided to allow flexibility
in grounding inputs for multiple op-amp configurations.
When a shunt is installed on JU1 or JU2, the corresponding input pad is referenced to ground. See Table
1 for JU1 and JU2 configuration. See the Op-Amp
Configuration section for more information regarding EV
kit configuration.
Shutdown Mode (SHDN)
Jumper JU3 controls the shutdown mode (SHDN) of the
device. When SHDN is pulled low, the device is enabled.
When the SHDN pin is pulled high, the device is
disabled. See Table 2 for JU3 configuration.
Table 1. JU1/JU2 Jumper Selection
SHUNT POSITION
IN-/IN+ INPUT
Installed
Connected to GND
Not installed*
Signal applied at IN-/IN+ pad
*Default position.
Table 2. JU3 Jumper Selection
SHUNT
POSITION
SHDN PIN
EV KIT
FUNCTION
1-2
Connected to VCC
Disabled
2-3*
Connected to GND
Enabled
*Default position.
Detailed Description of Hardware
The MAX9632 EV kit provides a proven layout for the
MAX9632 low-noise op amp to support multiple op-amp
configurations. The device accepts a single-supply
voltage from +4.5V to +36V, or a dual-supply voltage
from Q2.25V to Q18V.
2 Maxim Integrated
MAX9632 Evaluation Kit
Evaluates: MAX9632
Op-Amp Configuration
Transimpedance Application
To configure the EV kit as a transimpedance amplifier
(TIA), replace R2 with a 0I resistor, install a shunt on
jumper JU2, and capacitor C5 remains open. The output
voltage of the TIA is the input current multiplied by the
feedback resistor:
VOUT=
−
(IIN × IBIAS ) × R4 ± VOS
where R4 is installed as a 100I resistor, IIN is defined as
IN current, IBIAS is the input bias current, and VOS is the
input offset voltage of the op amp. Use capacitor C6 to
stabilize the op amp by rolling off high-frequency gain
due to a large cable capacitance.
Inverting Configuration
To configure the EV kit as an inverting amplifier, replace
R2 and R4 with the desired 1% gain-setting resistors,
install a shunt on jumper JU2, and feed a voltage VIN
between the IN- and IN+ pads. Install a shunt on JU2
to ground the IN+ input in this configuration. The output
voltage is given by the following equation:
R4
VOUT =
− (VIN + VOS )
R2
The offset voltage VOS can be either positive or negative.
Maxim Integrated
Noninverting Configuration
To configure the device as a noninverting amplifier,
replace R2 and R4 with the desired 1% gain-setting
resistors, and feed a voltage VIN between the IN+ and
IN- pads. Install a shunt on JU1 to ground the IN- input
in this configuration. The output voltage is given by the
following equation:
R4
VOUT =
(1 +
)(VIN ± VOS )
R2
Differential Amplifier
To configure the EV kit as a differential amplifier, replace
R1–R4 with appropriate resistors. Make sure R1 = R4
and R2 = R3. The CMRR of the differential amplifier is
determined by the matching of the resistor ratios R4/R2
and R1/R3:
R4 R1
=
VOUT =
Gain(INP − INN), where Gain =
R2 R3
Capacitive Loads
Some applications require driving large capacitive loads.
To improve the stability of the amplifier in such cases,
replace R5 with a suitable resistor value to improve
amplifier phase margin. The R5/C7 filter can also be
used as an anti-alias filter or to limit amplifier output noise
by reducing its output bandwidth.
3
MAX9632 Evaluation Kit
Evaluates: MAX9632
Figure 1. MAX9632 EV Kit Schematic
4 Maxim Integrated
MAX9632 Evaluation Kit
Evaluates: MAX9632
1.0”
Figure 2. MAX9632 EV Kit Component Placement Guide—
Component Side
1.0”
Figure 3. MAX9632 EV Kit PCB Layout—Component Side
1.0”
Figure 4. MAX9632 EV Kit PCB Layout—Solder Side
Maxim Integrated
5
MAX9632 Evaluation Kit
Evaluates: MAX9632
Revision History
REVISION
NUMBER
REVISION
DATE
0
10/10
Initial release
—
1
2/14
Corrected equations and descriptions of configurations
3
DESCRIPTION
PAGES
CHANGED
Maxim Integrated cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim Integrated product. No circuit patent
licenses are implied. Maxim Integrated reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and
max limits) shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance.
6
© 2014
Maxim Integrated 160 Rio Robles, San Jose, CA 95134 USA 1-408-601-1000
Maxim Integrated Products, Inc.
Maxim Integrated and the Maxim Integrated logo are trademarks of Maxim Integrated Products, Inc.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement