RW-5000F
VER 001
ROAD WEIGHER INDICATOR
OWNER
’S MANUAL
ROAD WEIGHER INDICATOR RW-5000F
NOTE
(1) The unauthorized copying of some or all of this manual is prohibited.
(2) The information contained herein is subject to change without notice.
(3) If there are any questions such as wrong or missing parts of the contents listed in this manual, please contact us.
(4) To improve the product performance, functions can be changed with no notice.
(5) Please understand that CAS does not have responsibility for a demand related to loss, lost profit etc. caused by operating the product, regardless of the third clause.
WARNING DEFINITIONS
This is warning & caution mark
This is hazard alert mark
This is useful information mark
- 2 -
ROAD WEIGHER INDICATOR RW-5000F
INDEX
1. Precautions ........................................................................... 4
2. Introduction ........................................................................... 5
3. Installation ............................................................................. 6
4. Description of Panels and Symbols ....................................... 7
5. Use of Battery Charger .......................................................... 9
6. Measurement of Axle Loads ................................................ 10
7. Alphabet Input ..................................................................... 13
8. Calling the Saved Data ........................................................ 16
9. Initialization of Memory ........................................................ 18
10. Real Time Clock .................................................................. 18
11. Setting Mode ....................................................................... 19
12. Test Mode ........................................................................... 23
13. RS-232C Interface .............................................................. 25
14. USB Interface ...................................................................... 27
15. Replacing the Paper Roll ..................................................... 28
16. Specifications ...................................................................... 30
17. Check Message .................................................................. 32
- 3 -
ROAD WEIGHER INDICATOR RW-5000F
1. Precautions
Please be informed that we’re not responsible for any incident or mishap caused by partial modification of this product. To avoid such situation, customers need to contact our customer service team or system installation staff in advance, and any modification should be conducted under our surveillance.
◆ Use only approved enhancements and batteries. Do not connect incompatible products. Use only batteries, chargers, adaptor, and enhancements approved by CAS for use with this particular model.
The use of any other types may invalidate any approval or warranty, and may be dangerous. For availability of approved enhancements, please check with your dealer.
◆ Do not install the indicator in strong direct sunlight and dust.
◆ Please confirm that the local voltage is correct for the indicator.
◆ Do not use inflammable substances for cleaning.
◆ Do not use the product in the rain. Keep it dry.
◆ Avoid sudden changes of temperature if possible
◆ Do not use the product in a place with a high-voltage current or severe electronic noise.
◆ Do not use the product in a place with severe vibration.
◆ Do not put too much pressure to keys.
◆ Avoid from the shock of excessive weight.
- 4 -
ROAD WEIGHER INDICATOR RW-5000F
2. Introduction
◆ Portable & watertight case
◆ Indicators for measuring axle
◆ Wireless communication: ZigBee
◆ Weigh-In-Motion and static weighing mode
◆ Built in thermal printer
◆ Memory capacity: 10K vehicles
◆ Standard RS232C
◆ Alert for over loaded vehicle
◆ Long battery lifetime by one time charging
◆ Optional USB host (For USB memory stick)
- 5 -
ROAD WEIGHER INDICATOR RW-5000F
3. Installation
Weighing method
Sequential
2 Axle, 2 Plate
Accuracy: ±1~3%
(WIM: ±3%)
[Scale ID]
Axle 1☞ Left: 1 / Right: 2
Synchronous
2 Axle, 4 Plate
Accuracy: ±0.1%
[Scale ID]
Axle 1☞ Left: 1 / Right: 2
Axle 2☞ Left: 3 / Right: 4
Synchronous
3 Axle, 6 Plate
Accuracy: ±0.1%
[Scale ID]
Axle 1☞ Left: 1 / Right: 2
Axle 2☞ Left: 3 / Right: 4
Axle 3☞ Left: 5 / Right: 6
Description
In case of Weigh-In-Motion (WIM), you must install the dummy pad (longer to the length of the vehicle) back and forth on scale.
Can be installed up to maximum 6 axles
- 6 -
ROAD WEIGHER INDICATOR RW-5000F
4. Description of Panels and Symbols
No. Name
1 Display
Description
Display the weight data & message
2 Antenna
3 Keypad
3dBi dipole antenna for wireless communication
Ten key and function key
4 Printer
5 USB port
6 DC jack port
7 RS232C port
Thermal printer
USB host port for memory stick
AC/DC Adaptor jack for battery charge
To PC communication port or firmware coding port
- 7 -
ROAD WEIGHER INDICATOR RW-5000F
4.1. Display specification
No.
1
Description
Indicates number of scales to be linked or sequence number
Example of display
(1 scale)
(3 scales)
(5 scales)
(7 scales)
(9 scales)
(11 scales)
(2 scales)
(4 scales)
(6 scales)
(8 scales)
(10 scales)
(12 scales)
2 Indicates in-motion mode
3 Indicates the status of the wireless connection
4 Displayed when the weight is minus
5 Indicates when a battery has to be recharged
6 Displayed when printing
7 Displayed when the type the alphabet.
8 Displayed when the weight is zero
9 Indicates the status of accumulated axle weight
10 Indicates the unit used to weight
11 Displayed when the weight is stable
- 8 -
ROAD WEIGHER INDICATOR RW-5000F
4.2. Keypad specification
Key Description
Turn on and off the indicator
~ Use to change input value and input data
Use to back light on and off
Use to change weight unit
The scale ’s unit is also changes
Return the display to zero
Use to print the accumulated weight
Line feed key of printer
Use to input he vehicle number
Use to confirm content of weight memory
Displays weight to be accumulated
Use to store current axle weight
5. Use of Battery Charger
◆ Connect adapter into charge connector (Check if the voltage is 12V 1A).
◆ If a battery jack is connected with an adaptor properly, RED lamp is on.
◆ If it’s charged completely, a green lamp is on.
(The estimated time for charging is about 10 hour but charging time can be varied according to environment condition.)
- 9 -
ROAD WEIGHER INDICATOR RW-5000F
6. Measurement of Axle Loads
6.1. Sequential weighing in static mode
1 Connect scales by wireless
2 Setting F03-0 and F01-2.
3
4
Initial display
→ Input the vehicle ID →
5
6
7
(For 2 seconds) → Input the item code →
1 st axle weighing → Stable lamp →
Stored the 1 st
axle weight
8
2 nd axle weighing → Stable lamp →
9 Repeat measures of axle weight ( 3 rd
, 4 th
, 5 th
)
10
11
6 th
axle(Last axle) weighing → Stable lamp →
Stored the 6 th
axle weight
12
13 → Print & Save
→ Displays weight to be accumulated
14 Repeat the same procedure for each vehicle to be loaded starting from step 3.
How to check an individual pad weight
Step 1: Press and hold key for 2 seconds, then “1 – 12” is displayed.
Step 2: Press scale ID number and then press
Step 3: The weight value of the scale is displayed.
key.
Step 4: To display the total weight of all scales again, you press
Undoing the accumulated data
The last axle weight data can be deleted from the accumulated data.
key
If you press key, clears the previous axle weight.
Vehicle ID & Item code input method: Refer to ‘7. Alphabet Input’
- 10 -
ROAD WEIGHER INDICATOR RW-5000F
6.2. Sequential weighing in WIM (Weigh-In-Motion)
1 Connect scales by wireless
2 Setting F03-1 and F01-2.
3
4
Initial display
→ Input the vehicle ID →
5
6
(For 2 seconds) → Input the item code →
1 st
axle weighing (WIM)
7 2 nd
axle weighing (WIM)
8 Repeat measures of axle weight ( 3 rd
, 4 th
, 5 th
)
9 6 th
axle(Last axle) weighing (WIM)
10
11 → Print & Save
→ Displays weight to be accumulated
12 Repeat the same procedure for each vehicle to be loaded starting from step 3.
When “SLO”, “FAST” message occurs, in order to initialize, press
Then, must be measured weight again from step 6.
Vehicle ID & Item code input method: Refer to ‘7. Alphabet Input’
key.
Maximum vehicle speed: 10km/h (6mi/h)
- 11 -
ROAD WEIGHER INDICATOR RW-5000F
6.3. Synchronous weighing method in static mode
1 Connect the scales by wireless (Example: 6 scales)
2 Setting F03-0 and F01-6.
3
4
Initial display
→ Input the vehicle ID →
5
(For 2 seconds) → Input the item code →
6 Loaded vehicle entry
7
8 → Print & Save
→ Displays weight to be accumulated
9 Repeat the same procedure for each vehicle to be loaded starting from step 3.
How to check an individual pad weight
Step 1: Press and hold key for 2 seconds, then “1 – 12” is displayed.
Step 2: Press scale ID number and then press key.
Step 3: The weight value of the scale is displayed.
Step 4: To display the total weight of all scales again, you press
Vehicle ID & Item code input method: Refer to ‘7. Alphabet Input’
key
- 12 -
ROAD WEIGHER INDICATOR RW-5000F
7. Alphabet Input
7.1. Input method
English input is similar to the way cellular phone.
Erase previous value
Enter key
Number/English conversion Space key
7.2. Input the vehicle ID
You can enter up to 10 characters. Vehicle ID is not stored in the memory.
For example (
“5-A”)
Step1: Press key in the weight mode, is displayed.
☞ ☞ ☞ ☞ Step2:
English input wait state
English keypad state
- 13 -
ROAD WEIGHER INDICATOR RW-5000F
7.3. Input the item code
You can enter up to 10 characters. Item code is not stored in the memory.
For example ( “IRON”)
Step1: Press and hold key for more 2 seconds, is displayed.
Step2: ☞ ☞ ☞ ☞ ☞
English input wait state
English keypad state
7.4. Input the customer details
You can enter up to 120 characters.
This data is stored in non-volatile memory, and is not lost even if power is off.
For example (
“WE WEIGH THE WORLD”)
key, Step1: When the indicator is power off press key while pressing
“ EDIT” is displayed.
Step2: Press key again, is displayed.
Step3: ☞ ☞
☞ ☞
☞
☞
☞
☞
☞
☞
☞ ☞ ☞
☞ ☞
☞ ☞
☞ ☞
English input wait state
English keypad state
- 14 -
ROAD WEIGHER INDICATOR RW-5000F
Delete the previous contents
Step1: When the indicator is power off press key while pressing
“ EDIT” is displayed.
Step2: Press
key,
key,
“ DELETE” is displayed and delete the previous contents.
Press key, exit this mode without any additional work.
7.5. The actual display (Alphabetical)
- 15 -
ROAD WEIGHER INDICATOR RW-5000F
8. Calling the Saved Data
Press key in the weight mode and “ 1 - 5” is displayed.
Refer to the call method of the downside and press to key.
Call the date
1
2
Input the year and date
→
Press
(October 13 th
2014)
key and execute the send to printer & PC
1
Call the serial number
2
Input the serial number
→
Press
(1234)
key and execute the send to printer & PC
Call the vehicle ID
1
2
Input the vehicle ID
→
Press
(5-A)
key and execute the send to printer & PC
Call the item code
1
2
Input the item code →
Press
(IRON)
key and execute the send to printer & PC
1
The entire call
Press key and execute the send to printer & PC
- 16 -
ROAD WEIGHER INDICATOR RW-5000F
8.1. Print form
Please refer to print form of page 20.
8.2. PC data format
◊ 1~20 byte
[Data & time] [Serial number]
1 4 / 1 0 / 1 3 , 1 5 : 1 2 , 0 1 2
◊ 21~41
[Vehicle ID] [Item code]
A B C D E 1 2 3 4 5 ,
3
A B C D E F G H
◊ 42~62
[Axle 1 weight: left / right / sum]
0 0 0 , l b , 0 1 0 0 0 , 0 1
◊ 63~80
[Axle 2 weight: left / right / sum]
, 0 2 0 0 0 , 0 2 0 0 0
◊ 81~98
[Axle 3 weight: left / right / sum]
, 0 3 0 0 0 , 0 3 0 0 0
◊ 99~116
[Axle 4 weight: left / right / sum]
, 0 4 0 0 0 , 0 4 0 0 0
◊ 117~134
[Axle 5 weight: left / right / sum]
,
,
,
0 4
0 6
0 8
, 0 2
0 0 0
0 0 0
0 0 0
,
I J
0 0 0
, 0 5 0 0 0 , 0 5 0 0 0
◊ 135~152
[Axle 6 weight: left / right / sum]
, 1 0 0 0 0
, 0 6 0 0 0 , 0 6 0 0 0 , 1 2 0 0 0
◊ 153~ 173
[Left sum] [Left %] [Right sum]
, 0 2 1 0 0 0 , 0 5 0 . 0 , 0 2 1 0
◊ 174~188
[Right %] [Amount]
0 0
0 5 0 . 0 , 0 4 2 0 0 0 , CR LF
,
- 17 -
ROAD WEIGHER INDICATOR RW-5000F
9. Initialization of Memory
It is used to initialize the data stored in the weight mode.
Stored data: Date, Time, Serial number, Item code, Vehicle ID and Weight.
When the indicator is power off press key while pressing
Then this mode is started.
Step 1. “ ----” message is shown on the display.
Step 2. Enter the password (1013), memory is cleared.
key,
10. Real Time Clock
It is used to initialize the data stored in the weight mode.
When the indicator is power off press key while pressing key,
Then this mode is started.
Step 1.
“ DATE” message is shown on the display.
Step 2. Input the year, date and press key
Step 1.
“ TIME” message is shown on the display.
Step 2. Input the current time and press key
Depending on the environment can cause errors. Therefore, recommended setting the time once a month.
- 18 -
ROAD WEIGHER INDICATOR RW-5000F
11. Setting Mode
6.1. How to enter
When the display is off, press key while pressing the key.
Step 1. At this time,
“F01” is shown on the display after “SET” message.
At this point, If you press key exit the mode.
Step 2. You can select the menu that you want to set. Enter number of set menu
key. by pressing the ten keys and then press
6.2. Function menu
◊ F01: Number of scales to be linked wireless (1~12)
Value Description
1
2
6
1 Scale
2 Scales
6 Scales
12 12 Scales
◊ F02: Stable condition (1~9) ▶ Initial value: 2
Value
1
5
Sensitive
Normal
Description
9 Insensitive
◊ F03: Weigh-In-Motion (0,1) ▶ Initial value: 0
Value Description
0 Not used
1 WIM
◊ F04: Backlight conditions (0~2) ▶
Initial value: 0
Value
0
1
2
Description
Manual ON/OFF
Automatic ON/OFF (Weighing: ON / Zero: OFF)
Always ON
- 19 -
ROAD WEIGHER INDICATOR RW-5000F
◊ F05: Backlight brightness level control (0~9) ▶ Initial value: 9
Value Description
0 10%
4 50%
The brightness of the backlight is adjusted depending on this parameter.
9 100%
◊ F06: Excess weight (0~999999) ▶ Initial value: 0
Value Description
0 Excess weight print function is not used.
20000
22000
If weight is greater than setting value, excess print function is active.
◊ F07: Print format (0~3) ▶ Initial value: 0
Description Value
0
1
Standard
Included left-right balance
2
3
Included inspector and driver
Included left-right balance, inspector and driver
WE WEIGH THE WORLD
------------------------
Customer details (Max. 5 lines – 120 characters)
DATE: 13/10/2014
TIME: 12:10
SN : 1234
ITEM: IRON
VEHICLE: AX13569PE
------------------------
1_AXLE:10000 lb/12000 lb
22000 lb
Item code (Max. 10 characters)
Vehicle ID (Max. 10 characters)
Excess: 2000 lb
2_AXLE:11000 lb/13000 lb
24000 lb
------------------------
TOTAL: 46000 lb
LEFT : 21000 lb (45.6%)
RIGHT: 26000 lb (53.4%)
------------------------
INSPECTOR:
In case of limit weight for axle is 20000 lb
Can measure up to six axles
F07-1 / F07-3
F07-2 / F07-3
DRIVER:
- 20 -
ROAD WEIGHER INDICATOR RW-5000F
◊ F08: Number of copies (0,1) ▶ Initial value: 0
Value Description
0
1
A sheet of paper
Two sheet of paper
◊ F09: Line feed (0~9) ▶
Initial value: 5
Value
0
Description
1 line feed automatically after printing
4
9
5 line feed automatically after printing
10 line feed automatically after printing
◊ F10: Enable printer (0,1) ▶
Initial value: 1
Value Description
0
1
Not used printer
Used printer
◊ F11: Baud rate for RS232C port (0~4) ▶
Initial value: 2
Value Description
0
1
2
2400 bps
4800 bps
9600 bps
3 19200 bps
4 38400 bps
◊ F12: Data bits, parity for RS232C port (0~2) ▶
Initial value: 0
Value
0
1
2
Description
Data 8 bits, Stop 1 bit, Non parity
Data 7 bits, Stop 1bit, Even parity
Data 7 bits, Stop 1bit, Odd parity
- 21 -
ROAD WEIGHER INDICATOR RW-5000F
◊ F13: Data format for auxiliary display (In case of F14-3) ▶ Initial value: 0
Value Description
0 22 bytes format (CAS standard)
1 18 bytes format
◊ F14: RS232C output (0~2) ▶ Initial value: 0
Refer to “13. RS-232C Interface”
Value
0
1
Description
Not used
Stream mode (Send the weight of each scales)
2
Press key (6.1-step13, 6.2-step11, 6.3-step8) to send the data
3 Stream mode (Depend on the setting of F13)
F14-1: Send a scale data 1 ☞ scale 2 ☞ scale 3 ☞ scale 4 ☞ scale 5
☞ scale 6 ☞ scale 1 ☞ scale 2 ….
F14-2: Send a scale data 1 ☞ scale 2 ☞ scale 3 ☞ scale 4 ☞ scale 5
☞ scale 6 ☞ Send a sum weight of scales
F14-3: Primarily, it is used to send a sum weight to auxiliary display unit.
◊ F15: External wireless output (0,1) ▶ Initial value: 0
Value
0 Not used
Description
1 To wireless auxiliary display unit
◊ F16: USB option (0,1) ▶
Initial value: 0
Value Description
0 Not used
1 Used
◊ F17: Power off sync (0,1) ▶ Initial value: 1
Refer to “14. USB Interface”
Value Description
0
1
Not used
When turn off the indicator, scales will turn off automatically
- 22 -
ROAD WEIGHER INDICATOR RW-5000F
12. Test Mode
12.1. How to enter
When the display is off, press key while pressing the key.
Step 1. At this time,
“TEST1” is shown on the display after “TEST” message.
At this point, If you press key exit the mode.
Step 2. You can select the menu that you want to test. Enter number of test menu by pressing the ten keys and then press
12.2. Test menu
◊ TEST 1: Keyboard test
Display
key.
Description
--
If you press a key that you want to test, the key number is appeared on the display.
◊ TEST 2: Wireless connect test
Display Description
1 - 12
Pressing the equipment ID of scales, the weight value of the scale is displayed.
◊ TEST 3: Printer test
Display Description
PRINT
Print the key is pressed.
◊ TEST 4: Back light test
Display
LIGHT
Description
Turn on the backlight the key is pressed.
- 23 -
ROAD WEIGHER INDICATOR RW-5000F
◊ TEST 5: Memory test
Display
MEMORY
GOOD
Description
Press key, and then
“GOOD” is displayed.
If flash memory has failed,
“ERROR” is displayed.
◊ TEST 6: Real time clock
Display Description
123056
Make sure the real time clock is goes.
- 24 -
ROAD WEIGHER INDICATOR RW-5000F
13. RS-232C Interface
13.1. Specifications
◊ Method: Full-duplex, asynchronous transmission format
◊ Baud rate: 2400, 4800, 9600, 19200, 38400 bps
◊ Data bit: 7, 8 bits
◊ Parity bit: Even or Odd (For 7 data bits) or Non parity (For 8 data bits)
◊ Start bit: 1bit / Stop bit: 1bit
◊ Code: ASCII
◊ Adaptable connector: D-SUB 9pin connector (Female)
1P 2P 3P 4P 5P 6P 7P 8P 9P
N.C. RXD TXD N.C. GND
13.2. Data format
N.C.
① Setting mode F14-1 or 2 ( : Space)
Vehicle ID Scale ID Weight data (8bytes) Unit Terminator
, , 2 4 4 0 l b C
R
L
F
Byte 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22
Data1 2 4 3 2 0 , 1 , 2 4 4 0 l b C
R
L
F
Data2 2 4 3 2 0 , 1 2 , 2 1 6 0 l b C
R
L
F
Data3 2 4 3 2 0 , T , 8 2 2 0 l b C
R
L
F
F14-1: Send the weight scale 1 ☞ scale 2 ☞ scale 3 ☞ scale 4 ☞ scale 5
☞ scale 6 ☞ scale 1 ☞ scale 2 ….
F14-2: Send the weight scale 1 ☞ scale 2 ☞ scale 3 ☞ scale 4 ☞ scale 5
☞ scale 6 ☞ Send a sum weight of scales (Scale ID “ T”)
- 25 -
ROAD WEIGHER INDICATOR RW-5000F
② Setting mode F14-3
◊ Format 1 (F13-0, 22bytes)
Header 1 Header 2 Fixed Data Unit Terminator
S T , G S , 1 , 8 2 2 0 l b C
R
L
F
ST Stable weight data (0x53) (0x54)
Header 1
US
OL
Unstable weight data (0x55) (0x53)
Overload (0x4F) (0x4C)
Header 2
HD
GS
Hold weight data (0x48) (0x44)
Gross data (0x47) (0x53)
Data
Example 1) 13.5kg
‘ ’, ‘ ’, ‘ ’, ‘ ’, ‘1’, ‘3’, ‘.’, ‘5’
Example 2) 135kg ‘ ’, ‘ ’, ‘ ’, ‘ ’, ‘1’, ‘3’, ‘5’, ‘ ’
Example 3) -13.5kg ‘-’, ‘ ’, ‘ ’, ‘ ’, ‘1’, ‘3’, ‘5’, ‘ ’
Unit
Terminator C
R
L
F
(0x0D) (0x0A)
◊ Format 2 (F13-1, 18bytes)
Header 1 Header 2 Data Unit Terminator
S T , G S , + 0 0 0 8 2 2 0 k g C
R
L
F
ST Stable weight data (0x53) (0x54)
Header 1 kg (0x6B) (0x67) / lb (0x6C) (0x62)
US
OL
Unstable weight data (0x55) (0x53)
Overload (0x4F) (0x4C)
Header 2
Data
Unit
Terminator
GS Gross data (0x47) (0x53)
The first of the data bit is the polarity (+/-) kg (0x6B) (0x67) / lb (0x6C) (0x62)
C
R
L
F
(0x0D) (0x0A)
- 26 -
ROAD WEIGHER INDICATOR RW-5000F
14. USB Interface
The USB host option is for sending the weight data to USB memory.
When you print weighing data, it is stored to USB memory stick.
If an error occurs at the time of storage, “CH 04” is displayed.
14.1. Specifications
◊ USB 2.0 compatible
◊ FAT32 file system
◊ Adaptable connector (USB A type/ Female)
If not use FAT32-formatted memory stick, it does not work.
14.2. Data format
◊ The file name is made by date
◊ The weighing data is stored sequentially in the same date file.
◊ Press
key (6.1-step13 / 6.2-step11 / 6.3-step8) to saves the data in the memory stick.
◊ When save the data to memory stick, RED lamp of USB port is lit.
Example: 140506.csv (Comma separated value - Excel file format)
14.3. Data capacity
◊ In case of 1G memory stick: Approx. 5,899,670 data
- 27 -
ROAD WEIGHER INDICATOR RW-5000F
15. Replacing the Paper Roll
Be sure to use paper rolls that meet the specifications.
Do not use paper rolls that have the paper glued to the core because the printer cannot detect the paper end correctly.
Step 1. Make sure that the printer is not receiving data.
Step 2. Open the paper roll cover by pressing the cover open button.
Do not open the print cover while the printer is operating.
Step 3. Remove the used paper roll core if there is one.
Step 4. Insert the paper roll as shown.
Be sure to note correct direction that the paper comes off the roll.
- 28 -
ROAD WEIGHER INDICATOR RW-5000F
Step 5. Pull out a small amount of paper, as shown. Then close the cover.
When closing the cover, Press the center of printer cover firmly to prevent paper miss-loading
Step 6. Tear off the paper as shown.
- 29 -
ROAD WEIGHER INDICATOR RW-5000F
16. Specifications
◆ General specifications
Display
Backlight
Operating temperature
Operating humidity
Net weight
Power
Charging adapter
Operating time
Option
◆ Printer specifications
Print method
Columns
Font size
Dot density
Total dots
Print speed
Print paper
Print width
Data buffer
Interface
Input power
Dimensions
6 digit FSTN LCD (Height: 20mm)
Amber LED backlight
-20℃ ~ 60℃
85% R.H. (No condensation)
Approx. 4.2kg
6V 10A lead-acid battery
AC/DC Adapter 12V 1A
Approx. 240hr
USB host (For memory stick, OP-01)
Thermal mechanism
24 on English
12 x 24
200 DPI(8dot/mm)
384 dots/line
60mm/sec
Ф40 x 57mm roll paper
48.0mm
16kbytes
RS-232C serial
6V 1.5A
77.5(W) x 51(D) x 81(H)
- 30 -
ROAD WEIGHER INDICATOR RW-5000F
◆ Wireless specifications
Wireless method
RF frequency range
Output power
Channel width
Frequency offset
Transmit data rate
Receiver sensitivity
Maximum input level
RF In/out impedance
Spurious(2nd harmonics)
Radio link effective range
◆ Dimensions
ZigBee
2400 ~ 2483.5 MHz
Max. 4dBm
2 MHz
< ±30ppm
250Kbps,500Kbps
-99dBm (PER <1%)
0dBm
50 ohm (TXRF, RXRF)
< -30dBm
Approx. 30M (Open space)
- 31 -
ROAD WEIGHER INDICATOR RW-5000F
17. Check Message
Code Description
CH 03 Something wrong in printer.
Please check printer and contact us to resolve this technical problem.
CH 04
Something wrong in USB port.
Please check your memory stick.
FAT32-formatted memory stick must be used.
PAPER
OVER
Displayed when there is no paper in the printer.
Replace the roll paper.
The scale ’s weight is over maximum capacity.
Don
’t load the article whose weight is heavier than the maximum capacity.
FULL When memory capacity was exceeded, this is displayed.
Please execute a memory initialization.
FAST In the WIM , occur when the vehicle’s speed is too fast.
Please pass the vehicle with 10km/h or less.
SLO
In the WIM
, occur when the vehicle’s speed is too slow.
RF 01
.
.
RF 12
When wireless connection is wrong, scale
’s ID is displayed.
Please check setting of F01 and ID of scale.
BATT 1
..
.
BATT12
When a scale's battery has to be recharged, scale ’s ID is displayed with once per every 5 seconds.
- 32 -
[MEMO]
ROAD WEIGHER INDICATOR RW-5000F
- 33 -
[MEMO]
ROAD WEIGHER INDICATOR RW-5000F
- 34 -
