ASW
INSTRUCTION MANUAL
DC ALARM
MODEL
■ FRONT PANEL CONFIGURATION
ASW
BEFORE USE ....
Thank you for choosing M-System. Before use, check the package you received as below.
If you have any problems or questions with the product, please contact M-System’s Sales Office or representatives.
■ PACKAGE INCLUDES:
Signal conditioner (body + base socket + input resistor) (1)
Input resistor is provided only with current input type.
■ MODEL NO.
Check that model No. described on specification label is exactly what you ordered.
■ INSTRUCTION MANUAL
This manual describes necessary points of caution when you use this product, installation, connection and basic maintenance procedures.
Hi Setpoint Monitor
Lo Setpoint Monitor
COM.
Hi Adj.
Lo Adj.
Hi LED
Lo LED
• Explanations
Hi and Lo Adjustments are used to set the alarm setpoints.
A 0 – 10V DC is output at the Hi and Lo setpoint monitor jacks across the COM jack, proportional to the setpoint 0 – 100%.
The Hi and Lo LED lights turn on when the coil for each relay is energized.
• Examples
For setting the relay to trip above 80% of the full-scale input signal, turn the Hi Adj. until you read 8.0V at the Hi Setpoint
Monitor.
COMPONENT IDENTIFICATION
Body Base Socket
Specification
Label
M•UNIT
Model
ASW
DC ALARM
SET
HI
LO
SET MONITOR
0–100%
(0–10VDC)
HI
LO
COM
Input Resistor
INSTALLATION
Detach the yellow clamps located at the top and bottom of the unit for separating the body from the base socket.
Clamp
(top & bottom)
DIN Rail
35mm wide
■ DIN RAIL MOUNTING
Set the base socket so that its
DIN rail adaptor is at the bottom. Position the upper hook at the rear side of base socket on the DIN rail and push in the lower. When removing the socket, push down the DIN rail adaptor utilizing a screwdriver
(–) and pull.
Spring Loaded
DIN Rail Adaptor
Shape and size of the base socket are slightly different with various socket types.
■ WALL MOUNTING
Refer to the drawings in the following page.
P. 1 / 3 EM-1611-B Rev.6
TERMINAL CONNECTIONS
Connect the unit as in the diagram below or refer to the connection diagram label on the front of the unit.
When an input resistor is provided with the module, attach it together with input wiring to the input screw terminals.
■ DIMENSIONS mm (inch)
CLAMP
(top & bottom)
7.8 (.31)
DIN RAIL
35mm wide
8 7 6 5
4
ASW
50 (1.97) 103 (4.06)
132 (5.20)
2–4.5 (.18) dia.
MTG HOLE
25 (.98) deep
11–M3.5
SCREW
[3.3 (.13)]
9
10 11
40 (1.57)
50 (1.97)
3
1 2
•When mounting, no extra space is needed between units.
■ TERMINAL ASSIGNMENTS mm (inch)
INPUT RESISTOR
(model: REM)
■ CONNECTION DIAGRAM
INPUT
+
–
R
*
5
6
3 N.C.
2 N.O.
HI OUTPUT
1 COM
11 N.C.
10 N.O.
LO OUTPUT
9 COM
7 U(+)
POWER
8 V(–)
* Input shunt resistor attached for current input.
8 7 6
4
5
9
10 11
3
1 2
Input shunt resistor attached for current input.
P. 2 / 3 EM-1611-B Rev.6
CHECKING
1) Terminal wiring: Check that all cables are correctly connected according to the connection diagram.
2) Power input voltage: Check voltage across the terminal 7
–␣ 8 with a multimeter.
3) Input: Check that the input signal is within 0 – 100% of the full-scale.
4) Alarm operations: Check the alarm operations referring to the figure below.
5) Output load: Check that the output load is 380V AC/
100VA or 125V DC/30W at the maximum. For maximum relay life with inductive load, external protection is recommended.
ASW
POINTS OF CAUTION
■ GENERAL
• Before you remove the unit from its base socket or mount it, turn off the power supply and input signal for safety.
■ ENVIRONMENT
• When heavy dust or metal particles are present in the air, install the unit inside proper housing and ventilate it.
• Do not install the unit where it is subjected to continuous vibration. Do not apply physical impact to the unit.
• Environmental temperature must be within -5 to +60
°
C (23 to 140
°
F) with relative humidity within 30 to 90% RH in order to ensure adequate life span and operation.
■ WIRING
• Do not install cables (power supply, input and output) close to noise sources (relay drive cable, high frequency line, etc.).
• Do not bind these cables together with those in which noises are present. Do not install them in the same duct.
■ AND ....
• The unit is designed to function as soon as power is supplied, however, a warm up for 10 minutes is required for satisfying complete performance described in the data sheet.
ALARM RELAY OPERATIONS
Hi Output
(1–3)ON
(1–2)ON
Lo Output
(9–10)ON
(9–11)ON
Input
(%) 0 ▲
Lo Setpoint
50 ▲
Hi Setpoint
100
• Trip operation in power failure: terminals 1 – 3, 9 – 11 turn
ON.
ADJUSTMENT PROCEDURE
Adjustment procedure for the Hi and Lo setpoints are as follows:
■ HOW TO ADJUST ALARM SETPOINTS
The monitor jacks output 0 – 10V DC in proportion to the 0
– 100% setpoints.
• Hi Setpoint
Measure the voltage at the Hi setpoint monitor jacks and turn the Hi Adj. until you read a desired value.
• Lo Setpoint
Measure the voltage at the Lo setpoint monitor jacks and turn the Hi Adj. until you read a desired value.
MAINTENANCE
Regular calibration procedure is explained below:
■ CALIBRATION
Warm up the unit for at least 10 minutes.
• Hi Setpoint
Increase the input signal from a value lower than the setpoint and check that the relay trips at the Hi setpoint (Measure the voltage at the Hi setpoint monitor jacks).
• Lo Setpoint
Decrease the input signal from a value higher than the setpoint and check that the relay trips at the Lo setpoint
(Measure the voltage at the Lo setpoint monitor jacks).
When the setpoints are shifted, recalibrate the unit according to the "ADJUSTMENT PROCEDURE" explained earlier.
M-SYSTEM WARRANTY
M-System warrants such new M-System product which it manufactures to be free from defects in materials and workmanship during the 36-month period following the date that such product was originally purchased if such product has been used under normal operating conditions and properly maintained, M-System's sole liability, and purchaser's exclusive remedies, under this warranty are, at M-System's option, the repair, replacement or refund of the purchase price of any M-System product which is defective under the terms of this warranty. To submit a claim under this warranty, the purchaser must return, at its expense, the defective M-System product to the below address together with a copy of its original sales invoice.
THIS IS THE ONLY WARRANTY APPLICABLE TO M-SYSTEM PRODUCT AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. M-SYSTEM SHALL HAVE NO LIABILITY FOR CONSEQUENTIAL, INCIDENTAL OR
SPECIAL DAMAGES OF ANY KIND WHATSOEVER.
M-System Co., Ltd., 5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN, Phone: (06) 6659-8201, Fax: (06) 6659-8510, E-mail: [email protected]
P. 3 / 3 EM-1611-B Rev.6