Amana | VR8205 | Installation guide | Amana VR8205 Installation guide

PACKAGE GAS-ELECTRIC
USER’S INFORMATION MANUAL
DESIGN
CE RT I F I E D
CE
RT IF IE D
®
®
WARNING
IF THE INFORMATION IN THESE INSTRUCTIONS IS NOT FOLLOWED EXACTLY, A FIRE OR EXPLOSION
MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.
–
DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND LIQUIDS IN THE
VICINITY OF THIS OR ANY OTHER APPLIANCE.
–
WHAT TO DO IF YOU SMELL GAS:
• DO NOT TRY TO LIGHT ANY APPLIANCE.
• DO NOT TOUCH ANY ELECTRICAL SWITCH; DO NOT USE ANY PHONE IN YOUR BUILDING.
• IMMEDIATELY CALL YOUR GAS SUPPLIER FROM A NEIGHBOR’S PHONE. FOLLOW THE GAS
SUPPLIER’S INSTRUCTIONS.
• IF YOU CANNOT REACH YOUR GAS SUPPLIER, CALL THE FIRE DEPARTMENT.
–
INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER, SERVICE AGENCY
OR THE GAS SUPPLIER.
Installer - Affix this manual, Installation Guide, and Warranty adjacent to the
appliance.
Owner -
Read and keep all product literature in a safe place for future
reference.
WARNING
WARNING
TO AVOID PROPERTY DAMAGE, PERSONAL INJURY OR DEATH, DO NOT USE
SHOULD OVERHEATING OCCUR, OR THE GAS SUPPLY FAIL TO SHUT OFF,
SHUT OFF THE MANUAL GAS VALVE TO THE FURNACE BEFORE SHUTTING OFF
THE ELECTRICAL SUPPLY.
THIS FURNACE IF ANY PART OF THE FURNACE HAS BEEN UNDER WATER.
IMMEDIATELY CALL A QUALIFIED SERVICE TECHNICIAN TO INSPECT THE
FURNACE AND TO REPLACE ANY PART OF THE CONTROL SYSTEM AND ANY
GAS CONTROL HAVING BEEN UNDER WATER.
WARNING
PRODUCT CONTAINS FIBERGLASS WOOL. DISTURBING THE INSULATION IN
THIS PRODUCT DURING INSTALLATION, MAINTENANCE, OR REPAIR WILL
EXPOSE YOU TO FIBERGLASS WOOL.
BREATHING THIS MAY CAUSE LUNG
STATE OF CALIFORNIA TO
CANCER. (FIBERGLASS WOOL IS KNOWN TO THE
CAUSE CANCER.)
FIBERGLASS WOOL MAY ALSO CAUSE RESPIRATORY, SKIN,
TO REDUCE EXPOSURE OR FOR FURTHER
AND EYE IRRITATION.
INFORMATION, CONSULT MATERIAL SAFETY DATA SHEETS AVAILABLE FROM
ADDRESS SHOWN BELOW OR CONTACT YOUR SUPERVISOR.
RECOGNIZE THIS SYMBOL AS A SAFETY PRECAUTION.
*NOTE: Please contact your distributor or our
website for the applicable product data book
referred to in this manual.
Part No. 10500226
Printed in U.S.A.
®
is a trademark of Maytag Corporation and is used under license to
Goodman Company, L.P. All rights reserved.
2002-2004 Goodman Company, L.P.
Effective: May 2004
SIGNAL WORDS
Dear Homeowner, please recognize the following safety information.
This information will alert you to the potential for personal injury.
Gutters or deflectors must be installed on the roof to prevent water
from shedding on the unit.
1. An area must be available to reach the unit in a clear and unobstructed path.
WARNING - Indicate hazards or unsafe practices which COULD 2. The unit area and the vicinity of any other gas appliances must
be kept clear and free of combustible materials, gasoline, and
result in severe personal injury or death.
other flammable vapors and liquids. Also, do not store or use
flammable items such as paint, varnish, or lacquer in the area.
CAUTION - Indicate hazards or unsafe practices which COULD
3. The combustion air supply must not be contaminated by prodresult in minor personal injury or product or property damage.
ucts containing chlorine or fluorine, as they could corrode the
heat exchanger. If you need further information on this subject,
WARNING
contact your installing dealer or another qualified servicer.
THIS PRODUCT CONTAINS OR PRODUCES A CHEMICAL OR CHEMICALS WHICH
MAY CAUSE SERIOUS ILLNESS OR DEATH AND WHICH ARE KNOWN TO THE
STATE OF CALIFORNIA TO CAUSE CANCER, BIRTH DEFECTS OR OTHER
REPRODUCTIVE HARM.
4. Familiarize yourself with the controls that turn off the gas and
electrical power to the unit. If the unit is to be shut down at the
end of the heating season, turn off both the gas and electrical
power. For safety, always turn them off before performing service
or maintenance on the unit.
5. Establish a regular service and maintenance schedule to ensure
efficient and safe operation of the unit.
WARNING
TO AVOID POSSIBLE EQUIPMENT DAMAGE, PERSONAL INJURY, FIRE OR
DEATH, THE FOLLOWING INSTRUCTIONS MUST BE OBSERVED REGARDING UNIT
LOCATION, AIR REQUIREMENTS AND OPERATING PROCEDURES.
6. The unit must be placed where no runoff water from higher ground
can collect in the unit.
UNIT INSTALLATION
Examine the unit installation to determine the following:
1. The vent connector is in place and is physically sound without
holes or excessive corrosion.
WARNING
HEATING UNIT SHOULD NOT BE UTILIZED WITHOUT REASONABLE, ROUTINE,
INSPECTION, MAINTENANCE AND SUPERVISION. IF THE BUILIDNG IN WHICH ANY
SUCH DEVICE IS LOCATED WILL BE VACANT, CARE SHOULD BE TAKEN THAT
2. The physical support of the unit is sound without sagging, cracks,
or gaps around the base so as to provide a seal between the
support and the base.
SUCH DEVICE IS ROUTINELY INSPECTED, MAINTAINED AND MONITORED. IN THE
3. There are no obvious signs of deterioration of the unit.
EVENT THAT THE BUILDING MAYBE EXPOSED TO FREEZING TEMPERATURES
4. The burner flames are stable, soft and blue, (dust may cause
orange tips but must not be yellow). The flames should extend
directly outward from the burner without curling, floating, or lifting
off. To examine, turn on the electrical power and gas. Set the
room temperature to the maximum setting.
AND WILL BE VACANT, ALL WATER-BEARING PIPES SHOULD BE DRAINED, THE
BUILDING SHOULD BE PROPERLY WINTERIZED, AND THE WATER SOURCE
CLOSED. IN THE EVENT THAT THE BUILDING MAY BE EXPOSED TO FREEZING
TEMPERATURES AND WILL BE VACANT, ANY HYDRONIC COIL UNITS SHOULD
BE DRAINED AS WELL AND, IN SUCH CASE, ALTERNATIVE HEAT SOURCES
SHOULD BE UTILIZED.
IMPORTANT NOTE TO THE OWNER
It is important that you fill out the owner’s registration card and mail it
today. This will assist us in contacting you should any service or
warranty information change in the future. When filling in the registration card, be sure to include the Model, Manufacturing and Serial
Numbers, plus the installation date. If the registration card cannot be
located, please call 1-877-254-4729 to register the furnace.
Your warranty certificate is also supplied with the unit. Read the
warranty carefully and note what is covered. Keep the warranty
certificate in a safe place, so you can find it, if necessary.
Before using this manual, check the serial plate for proper model identification.
The installation and servicing of this equipment must be performed by
qualified, experienced technicians only.
Check the burner flames for:
1. Good adjustment
2. Stable, soft and blue
3. Not curling, floating, or lifting off.
Burner
NOTE: If a strong wind is blowing, it may not be possible to perform
the flame inspection.
GENERAL INFORMATION
UNIT LOCATION
This unit is approved only for an outdoor installation. The diagram in the
Product Data Book applicable to your model* illustrates the required
clearances to the unit. It is important that safety measures are taken in
the surrounding area of the unit.
*NOTE: Please contact your distributor or our website for the applicable product data book referred to in this manual.
2
WARNING
WARNING
PERSONAL INJURY OR DEATH FROM ASPHYXIATION CAN RESULT FROM
EXPOSURE TO CARBON MONOXIDE. CARBON MONOXIDE OR “CO” IS A
TO AVOID PERSONAL INJURY OR FIRE, MINIMUM CLEARANCES TO
COMBUSTIBLE SURFACES MUST BE FOLLOWED.
COLORLESS AND ODORLESS GAS PRODUCED WHEN FUEL IS NOT BURNED
AIR REQUIREMENTS
COMPLETELY OR WHEN THE FLAME DOES NOT RECEIVE SUFFICIENT OXYGEN.
BE AWARE OF THESE AIR STARVATION SIGNALS WHICH INDICATE CONDITIONS
THAT MAY RESULT IN CARBON MONOXIDE OR THAT CARBON MONOXIDE MAY
WARNING
BE PRESENT:
1.
TO AVOID PROPERTY DAMAGE, PERSONAL INJURY OR DEATH, SUFFICIENT
2.
FRESH AIR MUST BE SUPPLIED FOR PROPER COMBUSTION AND VENTILATION
HEADACHES-NAUSEA-DIZZINESS, FLU-LIKE SYMPTOMS.
EXCESSIVE HUMIDITY-HEAVILY FROSTED WINDOWS OR A MOIST “CLAMMY”
FEELING IN THE HOME.
OF FLUE GASES.
3.
Since the gas/electric unit is installed completely in the outdoors, the
depletion of combustion air is highly improbable. To ensure an adequate
supply of combustion air, do not allow the air inlet hood or flue outlet hood
to become blocked by leaves, snow, rubbish, or insect (wasps) nests.
4.
SMOKE FROM A FIREPLACE WILL NOT DRAW UP THE CHIMNEY.
FLUE GASES THAT WILL NOT DRAW UP THE APPLIANCE VENT PIPE.
INDOOR HUMIDITY
Relative humidity is the amount of water vapor in the air relative to
the amount the air can hold at the same temperature. Example: At
40% relative humidity, the air could hold 2-1/2 times as much
moisture (2.5 x 40 = 100%) before becoming saturated.
Great care has been taken in the design and manufacture of your unit to
provide for your comfort and safety. Be aware of the possibility that some
problems with your unit or other gas-fired appliances could cause flue
gases to be present in your building. These flue gases could include
carbon monoxide.
The colder the air; the less moisture it can hold. As air is warmed,
its ability to hold moisture is increased. Example: A winter day,
outdoor temperature 10°F, and relative humidity of 70%. If that air
enters a home and is warmed to 72°F, the relative humidity will
drop to 6% (very dry) if no more moisture is added.
Relative humidity is important to your health and home as proper
humidification helps cut down on incidence of respiratory illness
and helps keep air cleaner and fresher.
A good relative humidity is one just high enough to barely start
condensation along the lower edges or lower corners of the
windows. More than that can be damaging.
Frequent fogging or excessive condensation on inside windows
indicates the indoor humidity level is too high for outdoor weather
conditions. Damage to the building may result if the condition
persists. (Condensation on inside of storm windows indicates
loose inside windows. Adding weather-stripping to tighten inside
windows usually corrects this problem.)
CARBON MONOXIDE POISONING HAZARD
Special Warning for Installation of Furnace or Air Handling Units in
Enclosed Areas such as Garages, Utility Rooms or Parking Areas
The following table shows the recommended maximum indoor
humidity in relationship to the outdoor temperatures.
Carbon monoxide producing devices (such as an automobile, space
heater, gas water heater, etc.) should not be operated in enclosed areas
such as unventilated garages, utility rooms or parking areas because of
the danger of carbon monoxide (CO) poisoning resulting from the exhaust
emissions. If a furnace or air handler is installed in an enclosed area such
as a garage, utility room or parking area and a carbon monoxide producing
device is operated therein, there must be adequate, direct outside
ventilation.
This ventilation is necessary to avoid the danger of CO poisoning which
can occur if a carbon monoxide producing device continues to operate in
the enclosed area. Carbon monoxide emissions can be (re)circulated
throughout the structure if the furnace or air handler is operating in any
mode.
Outdoor
Temperature
(°F)
Maximum
Indoor
%RH
+20
-10
0
-10
-20
35
30
25
20
15
Table 1
CO can cause serious illness including permanent brain damage or death.
B10259-216
WARNING
TO PREVENT PROPERTY DAMAGE OR
SERIOUS PERSONAL INJURY DUE TO
FIRE OR EXPLOSION CAUSED BY A PROPANE GAS LEAK, INSTALL A GAS
DETECTING WARNING DEVICE.
IF THE PROPANE GAS UNIT IS INSTALLED IN AN EXCAVATED AREA OR A
CONFINED SPACE, A WARNING DEVICE IS REQUIRED DUE TO:
•
PROPANE GAS IS HEAVIER THAN AIR AND ANY LEAKING GAS CAN
•
PROPANE GAS ODORANT MAY FADE, MAKING THE GAS UNDETECTABLE
SETTLE IN ANY LOW AREAS OR CONFINED SPACES.
EXCEPT WITH A WARNING DEVICE.
3
WARNING
AN UNDETECTED GAS LEAK WILL
WARNING
AN UNDETECTED GAS LEAK CAN CREATE A DANGER OF EXPLOSION
THE UNIT AND ITS GAS CONNECTIONS MUST BE LEAK TESTED
CREATE A DANGER OF EXPLOSION
OR FIRE.
OR FIRE. IF THE PRESENCE OF GAS IS SUSPECTED, FOLLOW THE
INSTRUCTIONS ON THE COVER OF THIS MANUAL.
FAILURE TO DO SO
BEFORE PLACING IN OPERATION.
COULD RESULT IN SERIOUS PERSONAL INJURY OR DEATH.
HEATING START UP
THERMOSTAT
To put your unit into operation, follow the steps listed below.
This unit will not operate properly without a good quality, correctly
installed thermostat. It is very important that the thermostat be
located where it can best “sense” the average room temperature.
Be sure the thermostat is not exposed to hot or cold drafts or to hot
or cold spots on the wall, such as those received from outside
walls, walls with pipes inside, or from openings into the attic.
1. Close the external manual gas shutoff valve.
2. Turn off the electrical power to the unit.
3. Set the room thermostat to the lowest possible setting.
4. Remove the heat exchanger door on the side of the unit by removing screws.
No matter the type or style, thermostat operation is basically the
same. The most widely used types will control both heating and
cooling functions and will have a Fan Switch with Auto and ON
settings. On Auto, the Circulating Air Blower will cycle on/off, but
if switched to ON it will run constantly.
5. This unit is equipped with an ignition device which automatically lights
the burner. Do not try to light the burner by hand.
6. Move (White-Rodgers Models 36E22, 36F22, and 36G22) or rotate
(Honeywell Model VR8205) the gas control switch to the OFF position. Do not use excessive force.
7. Wait five minutes to clear out any gas. Then smell for gas, including
near the floor as some types of gas are heavier than air.
IMPORTANT NOTE: To avoid the possibility of damage to the unit
heat exchanger, do not set the thermostat fan switch to ON
(constant fan operation) during the heating season without first
consulting the installer of the unit or another qualified servicer.
There are thermostats that automatically switch from Heating to
Cooling, or with night setbacks. The night setback, or multiple
setback type, will lower the temperature at night or during the day
when the building is unoccupied.
Room Temperature
Thermostat
Cool/Heat
Temperature
Control Dials
Fan Switch
System
Switch
OFF
Fan
Switch
AUTO
COOL
AUTO
COOL
ON
HEAT
AUTO
HEAT
ON
OFF
ON
Cool/Heat
Switch
8. If you smell gas following the five minute waiting period in step 7,
immediately follow the instructions onpage 2 this manual. If you do
not smell gas after five minutes, move or rotate the gas control switch
to the ON position. The switch should turn easily. Do not use excessive force.
9. Reinstall the burner compartment door.
10. Open the external manual gas shutoff valve.
Action
None
System only cools, fan
cycles off and on.
System only cools, fan
runs all the time.
System only heats, fan
cycles off and on.
System only heats, fan
runs all the time.
No heating or cooling,
fan runs all the time.
11. Turn on the electrical power to the unit.
12. Adjust the thermostat to a setting above room temperature.
13. After the burners are lit, set the thermostat to desired temperature.
HEATING SHUT DOWN
To shut down operation, follow the steps listed below.
Typical Thermostat
PROPANE (LP) GAS INSTALLATIONS ONLY
1. Set the thermostat to the lowest setting.
For units operating on propane gas, please review the following
warnings before use.
2. Turn OFF electrical power to the unit.
3. Remove the heat exchanger door on the side of the unit by removing
screws.
WARNING
TO AVOID PROPERTY DAMAGE, PERSONAL INJURY OR DEATH DUE TO
EXPLOSION OR FIRE, INSTALL A GAS DETECTING WARNING DEVICE. SINCE THE
ODORANT IN PROPANE GAS CAN BE REDUCED BY IRON OXIDE (RUST), A GAS
4. Move (White-Rodgers Models 36E22, 36F22, and 36G22) or rotate
(Honeywell Model VR8205) the gas control switch to the OFF position. Do not use excessive force.
5. Close the external manual gas shutoff valve.
DETECTING WARNING DEVICE IS THE ONLY RELIABLE METHOD TO DETECT
6. Reinstall the heat exchanger door.
PROPANE GAS LEAKS.
7. If cooling and/or air circulation is desired, turn ON the electrical power.
OPERATING INSTRUCTIONS
COOLING OPERATION
Cooling operation may be obtained as follows:
1. Place the room thermostat selector switch in the COOL position (or
AUTO, if available, and if automatic changeover from cooling to heating is desired).
WARNING
ELECTRICAL COMPONENTS ARE CONTAINED IN BOTH COMPARTMENTS.
TO AVOID PERSONAL INJURY, ELECTRICAL SHOCK OR DEATH, DO NOT
REMOVE ANY INTERNAL COMPARTMENT COVERS. CONTACT A
2. Set the room thermostat to the desired temperature.
3. If cooling system does not energize, wait five minutes. The system
startup may be delayed by the short-cycle protector feature of the
ignition control board. Check the manual reset devices on the rollout
limit, as described in this manual.
QUALIFIED SERVICER AT ONCE IF AN ABNORMAL CONDITION IS NOTICED.
4
Gas Valve
On/Off
Selector
Switch
O
F
F
INLET
ON
M
1
P
3
C
2
WARNING
IF THE SECONDARY LIMIT CONTROL SHOULD OPEN, THE REASON MUST BE
DETERMINED BEFORE THE CONTROL RESETS. THE ELECTRICAL POWER
OUTLET
MUST BE DISCONNECTED BEFORE ANY PANEL IS REMOVED OR MAINTENANCE IS PERFORMED.
Pressure Regulator
Adjustment
(Under Cap Screw)
Inlet Pressure Tap
(Side of Valve)
Outlet (Manifold)
Pressure Tap
(Side of Valve)
White-Rodgers Model 36E22
SECONDARY LIMIT
The secondary limit control is located on the blower housing and
monitors blower compartment temperatures. It is a normally closed
(electrically), automatic reset, temperature activated sensor. This
limit guards against overheating as a result of insufficient conditioned air passing over the heat exchanger. It deenergizes the gas
valve if the blower fails.
NOTE: If the power to the unit is interrupted during the heating cycle,
it may cause the secondary limit to trip. Once the blower compartment
temperature drops below the limit reset temperature, the limit will
automatically reset.
Gas Valve
On/Off
Selector
Switch
INLET
OUTLET
Inlet Pressure Tap
(Side of Valve) Pressure Regulator
Adjustment
(Under Cap Screw)
Secondary
Control Limit
Outlet (Manifold)
Pressure Tap
White-Rodgers Model 36F22
Pressure Regulator
Adjustment
(Under Cap Screw)
Outlet Pressure
Tap
OUTLET
INLET
Inlet Pressure
Tap
Back of Unit
Secondary Limit Control
Gas Valve
On/Off
Selector
Switch
ROLLOUT LIMIT
White-Rodgers Model 36G22
WARNING
THE CAUSE OF THE ROLLOUT PROTECTION DEVICE OPENING MUST BE INVESTIGATED BY A QUALIFIED SERVICER BEFORE ANY ATTEMPT IS MADE TO RESET
THE ROLLOUT PROTECTION DEVICE AND TURN THE UNIT BACK ON.
Pressure Regulator
Adjustment
(Under Cap Screw)
Outlet (Manifold)
Pressure Tap
Honeywell
INLET
OUTLET
ON
OFF
Inlet Pressure Tap
THE
ELECTRICAL POWER MUST BE DISCONNECTED BEFORE EITHER FRONT PANEL
IS REMOVED.
The rollout limit is a normally-closed (electrically), manual-reset,
temperature-activated sensor. It is mounted on the burner bracket
and monitors the burner flame. If there is an improper draw of burner
flames into the heat exchanger, the rollout limit will detect it and shut
off gas flowing to the burners. Contact a qualified servicer to check
the unit before resetting this device.
Gas Valve
On/Off
Control Knob
Rollout Protection
Honeywell Model VR8205
SAFETY CIRCUITS
A number of safety circuits are employed to ensure safe and proper
unit operation. These circuits serve to control any potential safety
hazards and, as inputs in the monitoring and diagnosis of abnormal
operation.
Rollout Protection on Burner Bracket
5
COMPRESSOR PROTECTION DEVICES
ensure that adequate combustion air is being drawn and the vent system
is working properly. Particular attention should be paid to the following
items. Repair as necessary.
This gas/electric package unit includes components which are
designed to protect the compressor against abnormal operating
conditions.
• Check physical support of the unit. Ensure it is sound without any
sagging, cracks, or gaps, around the base.
• Check for obvious signs of deterioration of the unit.
WARNING
TO PREVENT PERSONAL INJURY OR
• Flue and Air Inlet Hood. Check for blockage (wasp nest, etc.) and
corrosion.
DEATH, ALWAYS DISCONNECT THE
ELECTRICAL POWER BEFORE INSPECTING OR SERVICING THE UNIT.
SINCE
ALL OF THE COMPRESSOR PROTECTION DEVICES RESET AUTOMATICALLY,
THE CONTACTOR AND OUTDOOR FAN MAY BE ENERGIZED WHEN RESET.
Flue Hood
NOTE: The operation of the indoor blower will not be affected by any
compressor protection devices.
If, during a call for cooling, the indoor fan runs and circulates room
temperature air while the compressor and outdoor fan do not
operate:
1. Wait five minutes, as a protection device may be holding the
compressor off.
2. Check the room thermostat to see if it is correctly set.
Air Intake
Hood
3. If the room thermostat is correctly set, call a qualified servicer
to determine if one of the compressor protection devices has
opened.
Vent Hoods
• Return Air Connection. Check for physical soundness and ensure
that the connection is firmly sealed to the package unit casing.
SHORT-CYCLE PROTECTOR
A short-cycle protector is built into the ignition control. Each time
the compressor is off for less than 3 minutes, the short-cycle
protector will delay compressor startup for up to 3 minutes. This
protects the compressor from improper operation.
• Heat exchanger. Check for corrosion and/or obstructions within the
heat exchanger passageways.
• Burners. Check for proper ignition, burner flame, and flame sense.
Turn the electrical power and gas valve ON. Set the room thermostat to its maximum setting. Inspect the main burner flames. Flames
should extend directly outward from burners without curling, floating
or lifting off. Flames should be predominantly blue and directed into
the tubes. Although dust may cause orange tips, the flames must
not be yellow. Also check vestibule area for signs of deterioration.
Vacuum out the vestibule annually.
NOTE: These units are not designed to provide mechanical cooling
at outd oor temperatures below 50°F. If low ambient cooling is
needed, consult a qualified servicer.
IGNITER
The unit has an electronic ignition device which lights the burners
automatically. Never try to light the burners by hand. It also has
an induced draft blower to exhaust combustion products.
INDOOR AIR CIRCULATOR BLOWER
Keep the blower access door panel in place except for inspection
and maintenance.
Check the burner flames for:
1. Good adjustment
2. Stable, soft and blue
3. Not curling, floating, or lifting off.
ROUTINE MAINTENANCE
If you perform maintenance on the unit yourself, remember that
certain mechanical and electrical knowledge, skills and tools are
required to perform unit maintenance. Personal injury or death
may result If you are not properly trained. You should call your
installing dealer or place of purchase if you are uncertain about
your ability to perform maintenance.
Burner Flame
NOTE: If a strong wind is blowing, it may not be possible to perform
the flame inspection.
• Wiring. Check electrical connections for tightness and/or corrosion.
Check wires for damage.
WARNING
TO AVOID PERSONAL INJURY OR DEATH DUE TO EXPLOSION OR FIRE, THE
• Filters. Check that filters are clean and in the proper placement in
the unit or duct system.
FOLLOWING PROCEDURES MUST BE FOLLOWED EXACTLY IN SEQUENCE
BEFORE INSPECTING THE UNIT:
• TURN OFF GAS BY CLOSING EXTERNAL GAS SHUTOFF VALVE TO THE UNIT. • Louvers. Inspect louvers behind the air inlet hood on the unit. Ensure the area is clean and free of dirt and debris.
• TURN OFF ELECTRICAL POWER BY OPENING UNIT POWER DISCONNECT.
• IF THE UNIT HAS BEEN OPERATING, WAIT 15 MINUTES FOR IT TO COOL.
REPLACING OR CLEANING FILTER
IMPORTANT NOTE: Never operate unit without a filter installed as dust
and lint will build up on internal parts resulting in loss of efficiency,
equipment damage and possible fire.
ANNUAL INSPECTION
Your package unit should be inspected by a qualified installer, or
service agency at least twice every year. This check should be
performed before the heating and cooling seasons begin. This will
6
A return air filter is not supplied with this unit; however, there must be
a means of filtering the return air. The filter(s) may be located in the
return air duct(s). Consult with your installing dealer for the actual
location of the return air filter(s) in your unit.
FOR ADDITIONAL INFORMATION
Most questions can be answered by your local dealer. If you have
other matters that cannot be resolved locally, or you need additional information regarding other heating and cooling products
offered by us - please call:
See Product Data Book applicable to your model* for filter sizes.
A dirty filter is the most common cause of inadequate heating or
cooling performance. Filter inspection should be made at least every
two months; more often if necessary because of local conditions and
usage.
CONSUMER INFORMATION LINE
AMANA TOLL FREE
1-877-254-4729 (U.S. only)
email us at: customerservice@goodmanmfg.com
fax us at: (731) 856-1821
(Not a technical assistance line for dealers.)
Dirty throwaway filters should be discarded and replaced with a new,
clean filter. Dirty permanent filters should be washed with water,
thoroughly dried and sprayed with a filter adhesive before being
reinstalled. (Filter adhesives may be found at many hardware stores.)
Permanent filters should last several years. However, should one
become uncleanable, it should be replaced.
Outside the U.S., call 1-713-861-2500.
(Not a technical assistance line for dealers.)
Your telephone company will bill you for the call.
When installing a new filter or reinstalling an old one, always make
certain the air flow arrows on the filter point in the proper direction.
CLEAN OUTSIDE COIL (QUALIFIED SERVICER ONLY)
WARNING
Ask your participating dealer
about our extended service
plan. It adds to the strong
warranty with additional parts
and labor coverage.
TO AVOID PERSONAL INJURY OR DEATH DUE TO ELECTRICAL SHOCK,
DISCONNECT THE ELECTRICAL SWITCH BEFORE CLEANING THE COIL(S).
The coil with the outside air flowing over it should be inspected
annually and cleaned as frequently as necessary to keep the finned
areas free of leaves, grass, seeds, and debris.
SAFETY LABELS
INDOOR AIR CIRCULATOR BLOWER MOTOR LUBRICATION
The air circulator blower motor bearings are permanently lubricated
NOTE: If safety labels are missing or illegible, contact the installing
and do not require additional oiling.
dealer.
To obtain the proper safety labels, the Model, Manufacturing Number
INDUCED DRAFT BLOWER MOTOR LUBRICATION
The induced draft blower motor is permanently lubricated and does and Serial Number of the unit must be supplied. These numbers are
recorded on the nameplate of the unit. For convenience, record this
not require additional oiling.
information here:
OUTDOOR COIL FAN MOTOR LUBRICATION
The outdoor fan motor is permanently lubricated and does not require MODEL NUMBER: _ _ _ _ _ _ _ _ _ _ _
additional oiling.
MANUFACTURING NUMBER: P _ _ _ _ _ _ _ _
COMPRESSOR
The compressor motor is hermetically sealed and does not require
additional oiling.
Safety Labels
TO AVOID THE RISK OF
BURNS, PROPERTY
DAMAGE, PERSONAL
INJURY OR DEATH
WARNING
DO NOT APPLY POWER TO THIS
APPLIANCE OR COMPRESSOR IF
THE TERMINAL COVER HAS BEEN
REMOVED OR IS NOT FIRMLY IN
PLACE.
C8982701
WARNING
HEATING UNITS SHOULD NOT BE UTILIZED WITHOUT REASONABLE, ROUTINE,
INSPECTION, MAINTENANCE AND SUPERVISION. IF THE BUILDING IN WHICH
ANY SUCH DEVICE IS LOCATED WILL BE VACANT, CARE SHOULD BE TAKEN
THAT SUCH DEVICE IS ROUTINELY INSPECTED, MAINTAINED AND MONITORED.
IN THE EVENT THAT THE BUILDING MAY BE EXPOSED TO FREEZING TEMPERATURES AND WILL BE VACANT, ALL WATER-BEARING PIPES SHOULD BE
DRAINED, THE BUILDING SHOULD BE PROPERLY WINTERIZED, AND THE
WATER SOURCE CLOSED. IN THE EVENT THAT THE BUILDING MAY BE
EXPOSED TO FREEZING TEMPERATURES AND WILL BE VACANT, ANY
HYDRONIC COIL UNITS SHOULD BE DRAINED AS WELL AND, IN SUCH CASE,
ALTERNATIVE HEAT SOURCES SHOULD BE UTILIZED.
B14933-206
7
Safety Labels
WARNING: IMPROPER INTALLATION, ADJUSTMENT, ALTERATION, SERVICE OR MAINTENANCE CAN CAUSE PROPERTY
DAMAGE, PERSONAL INJURY OR LOSS OF LIFE, OR EXPOSURE
TO SUBSTANCES IN FUEL OR FROM FUEL COMBUSTION WHICH
CAN CAUSE DEATH OR SERIOUS INJURY, AND WHICH ARE
KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER,
BIRTH DEFECTS, OR OTHER REPRODUCTIVE HARM. REFER
TO THE USER'S INFORMATION MANUAL PROVIDED WITH
THIS FURNACE. INSTALLATION AND SERVICE MUST BE
PERFORMED BY A QUALIFIED INSTALLER, SERVICE
AGENCY OR THE GAS SUPPLIER.
ATTENTION! UN NIVEAU INADEQUAT DE MONTAGE,
REGLAGE, ADJUSTEMENT, SERVICE OU MANUTENTION PEUT
ENTRAINER DES DEGATS MATERIAUX, DES BLESSURES OU
LA MORT, RAPPORTEZ-VOUS AU MANUEL D'UTILISATION
FOURNI AVEC CE FOUR. LE MONTAGE ET L'ENTRETIEN
DOIVENT ETRE REALISES PAR UN TECHNICIEN
QUALIFIE, UNE AGENCE D'ENTRETIEN, OU LE
FOURNISSEUR DE GAZ.
POUR VÔTRE SÛRETE
FOR YOUR SAFETY
NE METTEZ PAS ET N'UTILISEZ PAS DE COMBUSTIBLE
OU DES VAPEURS ET LIQUIDES FLAMMABLES
PRES DE CET APPAREIL OU DES AURTES.
DO NOT STORE OR USE GASOLINE OR OTHER
FLAMMABLE VAPORS AND LIQUIDS IN THE VICINITY
OF THIS OR ANY OTHER APPLIANCE.
LE MODE D'EMPLOI SE TROUVE APPOSE A L'INTERIEUR
DE CE PANNEAU D'ACCES.
SEE INSIDE SURFACE OF THIS DOOR FOR
LIGHTING/OPERATING INSTRUCTIONS.
WARNING
R isk o f ele ctric sh o ck o r de a th.
10543401
CAUTION
TO PREVENT BURNS
D isc o nn e ct re m o te e lec tric po w e r
su p ply o r su pp lies be fo re s e rvicing .
DO NOT TOUCH HOT
Th is co m pa rtm e nt m u st b e c lo s ed
ex ce pt w h e n se rvicin g.
HOOD SURFACES
C6496101
AVERTISSEMENT
Danger de choc électrique ou
de mort.
Débrancher toute boite á fusibles
avant l'entretien.
Ce compartment doit rester ferme,
sauf pour l'entretien.
WARNING
FOR YOUR SAFETY
READ BEFORE OPERATING
WARNING: If you do not follow these instructions
explosion may result causing property damage,
personal injury or loss of life.
la lettre les instructions dans le présent manuel
risque de déclecher un incendie ou une explosion
entraînant des dammages matériels, des lésions
corporelles ou la perte de vies humaines.
A. This appliance does not have a pilot. It is equipped
with an ignition device which automatically lights
the burner. Do not try to light the burner by hand.
A. Cet appareil ne comporte pas de veilleuse. Il est
B. BEFORE OPERATING smell all around the appliance
area for gas. Be sure to smell next to the floor
because some gas is heavier than air and will
settle on the floor.
FIRE AND/OR SEVERE
PERSONAL INJURY HAZARD.
REFRIGERANT MUST BE
REMOVED FROM BOTH THE
LOW AND HIGH PRESSURE
SIDES OF THE SYSTEM
BEFORE HEAT IS APPLIED.
WHAT TO DO IF YOU SMELL GAS
10466601
LIRE AVANT DE METTRE
EN MARCHELIRE
AVERTISSEMENT: Quiconque ne respecte pas á
Do not try to light any appliance.
Do not touch any electric switch;
do not use any phone in your building.
Immediately call your gas supplier from a neighbor's
phone. Follow the gas supplier's instructions.
If you cannot reach your gas supplier,
call the fire department.
C. Use only your hand to push in or turn the gas control lever.
Never use tools. If the lever will not push in or turn by
hand, don't try to repair it, call a qualified service
technician. Force or attempted repair may result in a fire
or explosion.
D. Do not use this appliance if any part has been underwater.
Immediately call a qualified service technician to inspect
the appliance and to replace any part of the control
system and any gas control which has been underwater.
muni d'un dispositif d'allumage qui allume
automatiquement le brûleur. Ne pas tenter
d'allumer le brûleur manuellement.
B. AVANT DE LE FAIRE FONCTIONNER,
renifler tout autour de l'appariel pour déceler
une odeur de gaz. Renifler près du plancher, car
certains gaz sont plus lourds que l'air et
peuvent s'accumuler au niveau du so.l
QUE FAIRE S'IL Y A UNE ODEUR DE GAZ
Ne pas tenter d'allumer l'appariel
Ne toucher aucun interrupteur électrique;
n'utiliser aucun téléphone dans le bâtiment.
Appeler immédiatement le fournisseur de gaz
en employant le téléphone dún voisin.
Respecter à la lettre les instructions du
fournisseur de gaz.
Si personne ne répond, appeler le service des
incendies.
C. Ne pousser ou tourner le levier d'admission du gaz
qu'à la main; ne jamais emploer d'outil à cet effet.
Si la manette reste coincée, ne pas tenter de la
réparer; appeler un technicien qualifié. Quiconque
tente de forcer la manette ou de la reparer peut
déclencher une explosion ou un incendie.
D. Ne pas se servir de cet appareil s'il a été plongé
dans l'eau, complètement ou en partie. Appeler un
technicien qualifié pour inspecter l'appareil et
remplacer tout partie du système de contrôle et
toute commande qui ont été plongés dans l'eau.
MISE EN MARCHE
OPERATING INSTRUCTIONS
CARBON MONOXIDE POISONING HAZARD
Special Warning for Installation of Furnace or Air Handling Units in
Enclosed Areas such as Garages, Utility Rooms or Parking Areas
Carbon monoxide producing devices (such as an automobile, space
heater, gas water heater, etc.) should not be operated in enclosed areas
such as unventilated garages, utility rooms or parking areas because of
the danger of carbon monoxide (CO) poisoning resulting from the exhaust
emissions. If a furnace or air handler is installed in an enclosed area such
as a garage, utility room or parking area and a carbon monoxide producing
device is operated therein, there must be adequate, direct outside
ventilation.
This ventilation is necessary to avoid the danger of CO poisoning which
can occur if a carbon monoxide producing device continues to operate in
the enclosed area. Carbon monoxide emissions can be (re)circulated
throughout the structure if the furnace or air handler is operating in any
mode.
CO can cause serious illness including permanent brain damage or death.
B10259-216
1. STOP! Read the safety information above on
this label.
2. Set the thermostat to lowest setting.
3. Turn off all power to the appliance.
4. This appliance is equipped with an ignition.
device which automatically lights the burner.
Do not try to light the burner by hand.
5. Push the gas control lever to "OFF" Position.
Do not force.
6. Wait five (5) minutes to clear out any gas. Then
smell for gas, including near the floor. If you
then smell gas, STOP! Follow "B"
in the safety. information above
on this label if you don't smell
gas, go to next step.
GAS
7. Push gas control lever
INLET
to "ON".
8. Replace access panel.
9. Turn on all electric
ARRIVEE
DU GAZ
power to the appliance.
10.Set thermostat to desired setting.
11.If the appliance will not operate,
follow the instructions "To Turn
Off Gas To Appliance" and call your
service technician or gas company.
ROBINET A GAZ
MANUEL, EN POS
"ON/MARCHE"
MANUAL GAS
LEVER SHOWN
IN ON POSITION
TO TURN OFF GAS TO APPLIANCE
1. Set the thermostat to lowest setting.
2. Turn off all electric power to the appliance
if service is to be performed.
3. Push the gas control lever to "OFF" Position.
Do not force.
4. Replace control access panel.
1. ARRETÊR! Lisez les instructions de sécurité sur
la portion supérieure de cette étiquette.
. 2. Régler le thermostat à la température la plus basse
3. Couper l'alimentation électrique de l'appareil.
4. Cet appareil ménager étant doté d'un système
d'allumage automatique, ne pas essayer à
allumer le brûleur manuellement.
5. Pousse le levier du contrôle du gaz à "OFF/ ARRET"
position.
6. Attendre cinq (5) minutes pour laisser echapper tout le
gaz. Renifler tout autour de l'appareil, y compris près du
plancher, pour déceler une odeur de gaz. Si c'est le cas,
ARRETER! Passer à l'étape B des instructions de sécuritié
sur la portion supérieure de cette étiquette.
S'il n'y a pas d'odeur de gaz, passer à l'étape suivanté.
7. Pousse le levier du contrôle du gaz à "ON/MARCHE"
position.
8. Remettre en place le panneau d'accés.
9. Mettre l'appareil sous tension.
10. Régler le thermostat à la température desirée.
11. Si l'appareil ne se met pas en marche, suiyre les
instructions intitulées. Comment coupler l'admission
de gaz de l'appereil et appeler un technicien
qualifié ou le fourrnisseur de gaz.
POUR COUPER L'ADMISSION
DE GAZ DE L'APPAREIL
1. Régler le thermostat à la température la plus basse.
2. Couper l'alimentation électrique de l'appareil s'il
faut procéder à des opérations d'entretien.
3. Pousse le levier du contrôle du gaz à "OFF / ARRET"
position.
Ne pas forcer.
4. Remettre en place le panneau d'accès.
11072712
2002-2004 Goodman Company, L.P.
Effective: May 2004
8
Download PDF