User's Guide | Epson PowerLite Home Cinema 700 User`s guide

PowerLite

®

Home Cinema 700

Quick Setup

Before using the projector, read these instructions and the safety instructions in the

User’s Guide on your projector CD-ROM.

1

Unpack the projector

You should have the following items:

Projector Power cord Component-to-VGA adapter

3

Set up the remote control

1

Remove the battery cover.

2

Insert the batteries.

3

Replace the battery cover.

4

Plug in and turn on

1

Open the A/V Mute slide (lens cover).

Turning off the projector

1

If you’re using a computer, shut it down first, while you can still see the display.

2

Press the power button on the projector or remote control.

3

When you see the confirmation message, press the power button again. The projector beeps twice and the power light turns orange.

With Epson’s Instant Off ® technology, there’s no cool-down period. When you’re done, just unplug the projector and it’s ready to travel.

5

Connect your video source

Follow these instructions to connect the projector to your video equipment using an HDMI cable or component video cable and adapter.

For instructions on using other connection options, or connecting to a computer, see the User’s Guide on your CD-ROM.

Connecting with an HDMI cable

For the best image and sound quality, connect your video equipment to the

HDMI port, if possible.

1

Connect an HDMI cable (not included) to the HDMI port on your video player and the HDMI port on the projector.

User’s Guide

CD-ROM

Interface label stickers

(Included for Canada only)

Projector remote control

Batteries

Canada only: For French speakers, remove sticker(s) from the interface label backing sheet and place over corresponding text on the control panel.

2

Choose a location

The easiest way to set up your projector is to place it on a table in front of your screen or wall, or on a high shelf behind you. See the User’s Guide for other ways of setting up the projector.

Table Shelf

2

Connect the power cord to the projector and plug the other end into an electrical outlet.

The power light on the projector turns orange.

Power light

Power button

2

Start your video or presentation. Use the Source Search button on the projector or the Search button on the remote control to select the HDMI source, if necessary.

Connecting with a component video cable

If your video equipment has component video connectors (three connectors labeled either Y/Cb/Cr or Y/Pb/Pr), you can use a component video cable (not included) along with the included component-to-VGA adapter.

1

Connect your component video cable to your video device.

2

Connect the component-to-VGA adapter that came with your projector to the component video cable.

3

Connect the VGA end of the adapter to the projector’s Computer

(Component Video) port.

The distance between the projector and the screen generally determines the size of the image, but the size can also vary depending on the aspect ratio

(image shape), how you zoom into the image, and whether you’ve adjusted other image settings. Depending on the image settings you’ve chosen, you can place the projector anywhere from 33 to 407 inches (84 to 1035 cm) from the screen.

Use the tables in the User’s Guide, or the Image Size or Projection Distance calculator on the Multimedia Projectors page on Epson’s website to help you determine the proper projection distance.

3

Connect your video source, as described to the right.

4

Turn on your computer or video source.

5

Press the power button on the projector or remote control. The projector beeps, the power light flashes green, and the projector warms up. When the power light stays green, the projector is ready for use.

Power button

*411537000*

*411537000*

4

You can connect an optional audio cable if you want to play sound through the projector. See the User’s Guide on your CD-ROM for instructions.

5

Start your video or presentation. Use the Source Search button on the projector or the Search button on the remote control to select the video source, if necessary.

Turn over

PowerLite

®

Home Cinema 700

Quick Setup

Before using the projector, read these instructions and the safety instructions in the

User’s Guide on your projector CD-ROM.

1

Unpack the projector

You should have the following items:

Projector Power cord Component-to-VGA adapter

3

Set up the remote control

1

Remove the battery cover.

2

Insert the batteries.

3

Replace the battery cover.

4

Plug in and turn on

1

Open the A/V Mute slide (lens cover).

Turning off the projector

1

If you’re using a computer, shut it down first, while you can still see the display.

2

Press the power button on the projector or remote control.

3

When you see the confirmation message, press the power button again. The projector beeps twice and the power light turns orange.

With Epson’s Instant Off ® technology, there’s no cool-down period. When you’re done, just unplug the projector and it’s ready to travel.

5

Connect your video source

Follow these instructions to connect the projector to your video equipment using an HDMI cable or component video cable and adapter.

For instructions on using other connection options, or connecting to a computer, see the User’s Guide on your CD-ROM.

Connecting with an HDMI cable

For the best image and sound quality, connect your video equipment to the

HDMI port, if possible.

1

Connect an HDMI cable (not included) to the HDMI port on your video player and the HDMI port on the projector.

User’s Guide

CD-ROM

Interface label stickers

(Included for Canada only)

Projector remote control

Batteries

Canada only: For French speakers, remove sticker(s) from the interface label backing sheet and place over corresponding text on the control panel.

2

Choose a location

The easiest way to set up your projector is to place it on a table in front of your screen or wall, or on a high shelf behind you. See the User’s Guide for other ways of setting up the projector.

Table Shelf

2

Connect the power cord to the projector and plug the other end into an electrical outlet.

The power light on the projector turns orange.

Power light

Power button

2

Start your video or presentation. Use the Source Search button on the projector or the Search button on the remote control to select the HDMI source, if necessary.

Connecting with a component video cable

If your video equipment has component video connectors (three connectors labeled either Y/Cb/Cr or Y/Pb/Pr), you can use a component video cable (not included) along with the included component-to-VGA adapter.

1

Connect your component video cable to your video device.

2

Connect the component-to-VGA adapter that came with your projector to the component video cable.

3

Connect the VGA end of the adapter to the projector’s Computer

(Component Video) port.

The distance between the projector and the screen generally determines the size of the image, but the size can also vary depending on the aspect ratio

(image shape), how you zoom into the image, and whether you’ve adjusted other image settings. Depending on the image settings you’ve chosen, you can place the projector anywhere from 33 to 407 inches (84 to 1035 cm) from the screen.

Use the tables in the User’s Guide, or the Image Size or Projection Distance calculator on the Multimedia Projectors page on Epson’s website to help you determine the proper projection distance.

3

Connect your video source, as described to the right.

4

Turn on your computer or video source.

5

Press the power button on the projector or remote control. The projector beeps, the power light flashes green, and the projector warms up. When the power light stays green, the projector is ready for use.

Power button

*411537000*

*411537000*

4

You can connect an optional audio cable if you want to play sound through the projector. See the User’s Guide on your CD-ROM for instructions.

5

Start your video or presentation. Use the Source Search button on the projector or the Search button on the remote control to select the video source, if necessary.

Turn over

PowerLite

®

Home Cinema 700

Quick Setup

Before using the projector, read these instructions and the safety instructions in the

User’s Guide on your projector CD-ROM.

1

Unpack the projector

You should have the following items:

Projector Power cord Component-to-VGA adapter

3

Set up the remote control

1

Remove the battery cover.

2

Insert the batteries.

3

Replace the battery cover.

4

Plug in and turn on

1

Open the A/V Mute slide (lens cover).

Turning off the projector

1

If you’re using a computer, shut it down first, while you can still see the display.

2

Press the power button on the projector or remote control.

3

When you see the confirmation message, press the power button again. The projector beeps twice and the power light turns orange.

With Epson’s Instant Off ® technology, there’s no cool-down period. When you’re done, just unplug the projector and it’s ready to travel.

5

Connect your video source

Follow these instructions to connect the projector to your video equipment using an HDMI cable or component video cable and adapter.

For instructions on using other connection options, or connecting to a computer, see the User’s Guide on your CD-ROM.

Connecting with an HDMI cable

For the best image and sound quality, connect your video equipment to the

HDMI port, if possible.

1

Connect an HDMI cable (not included) to the HDMI port on your video player and the HDMI port on the projector.

User’s Guide

CD-ROM

Interface label stickers

(Included for Canada only)

Projector remote control

Batteries

Canada only: For French speakers, remove sticker(s) from the interface label backing sheet and place over corresponding text on the control panel.

2

Choose a location

The easiest way to set up your projector is to place it on a table in front of your screen or wall, or on a high shelf behind you. See the User’s Guide for other ways of setting up the projector.

Table Shelf

2

Connect the power cord to the projector and plug the other end into an electrical outlet.

The power light on the projector turns orange.

Power light

Power button

2

Start your video or presentation. Use the Source Search button on the projector or the Search button on the remote control to select the HDMI source, if necessary.

Connecting with a component video cable

If your video equipment has component video connectors (three connectors labeled either Y/Cb/Cr or Y/Pb/Pr), you can use a component video cable (not included) along with the included component-to-VGA adapter.

1

Connect your component video cable to your video device.

2

Connect the component-to-VGA adapter that came with your projector to the component video cable.

3

Connect the VGA end of the adapter to the projector’s Computer

(Component Video) port.

The distance between the projector and the screen generally determines the size of the image, but the size can also vary depending on the aspect ratio

(image shape), how you zoom into the image, and whether you’ve adjusted other image settings. Depending on the image settings you’ve chosen, you can place the projector anywhere from 33 to 407 inches (84 to 1035 cm) from the screen.

Use the tables in the User’s Guide, or the Image Size or Projection Distance calculator on the Multimedia Projectors page on Epson’s website to help you determine the proper projection distance.

3

Connect your video source, as described to the right.

4

Turn on your computer or video source.

5

Press the power button on the projector or remote control. The projector beeps, the power light flashes green, and the projector warms up. When the power light stays green, the projector is ready for use.

Power button

*411537000*

*411537000*

4

You can connect an optional audio cable if you want to play sound through the projector. See the User’s Guide on your CD-ROM for instructions.

5

Start your video or presentation. Use the Source Search button on the projector or the Search button on the remote control to select the video source, if necessary.

Turn over

6

Adjust the image

1

To raise the image, press the foot release lever and lift the front of the projector. Release the lever to lock the foot in position.

Remote Control Map

Search and individual Source selection buttons Power button

2

Rotate the focus ring to sharpen the image. To reduce or enlarge the image, rotate the zoom ring.

Focus ring

Zoom ring

3

If your image looks like or , first make sure the projector is facing the screen squarely. Then, if necessary, press the and

buttons on the projector’s control panel until the image looks correct.

4

To select the best color mode, press the Color Mode button on the remote control. Press it repeatedly to move through the options.

A/V Mute button

Turns off image

Auto button

Resets tracking, sync, and position

Aspect button

Changes screen size

Page Up/Down buttons

Control PowerPoint ® slides

(USB cable required)

E-Zoom +/– buttons

Zoom into image details

Menu button

Accesses menus

Freeze button

Stops image

Color Mode button

Changes display mode

Num button

Activates number buttons

Help button

Displays help menus

Volume buttons

Adjust volume

Esc button

Exits menus

Menu navigation buttons and Enter button

Troubleshooting

If you see a blank screen

If you see a blank screen or the No signal message after turning on your computer or video source, check the following:

 Make sure the power light on the projector is green and not flashing and the A/V Mute slide (lens cover) is open.

 Make sure the cables are connected correctly. (See the User’s Guide for more information.)

 If you’ve connected more than one video source, you may need to press the Source Search button on the projector or the Search button on the remote control to select the one you want to watch.

(Allow a few seconds for the projector to sync up after pressing it.)

If the picture is taller on one side

The projector is set at an angle to the screen. Face it squarely toward the screen.

Aspect button Color Mode button

5

If the image is stretched or cut off, press the Aspect button until the image looks correct.

See your User’s Guide on the CD-ROM for more information about image adjustments.

7

Install User’s Guide and register your projector

1

Insert the projector CD-ROM in your drive. If the installer doesn’t open automatically, double-click the Epson CD-ROM icon, then double-click the Epson installer icon.

2

Select English.

3

Follow the instructions on the screen to register.

NOTE

You can also register at www.epson.com/webreg.

4

After you register the projector, click User’s Guide to install it.

(If you are using Windows and don’t already have Adobe ®

Reader ® , click Adobe Reader and follow the on-screen instructions to install it.)

5

When you’re done, click Exit.

To open your User’s Guide, double-click the PL HC700 User’s Guide

icon on your desktop.

Where to get help

Internet support

Visit Epson’s support website at epson.com/support and select your product for solutions to common problems. You can download utilities and documentation, get FAQs and troubleshooting advice, or e-mail Epson with your questions.

Speak to a support representative

To use the Epson PrivateLine ® Support service, call (800) 637-7661 and enter the PIN on the Epson PrivateLine Support card that came with your projector.

This service is available 6 AM to 6 PM , Pacific Time, Monday through Friday, for the duration of your warranty period. You may also speak with a projector support specialist by dialing one of the following numbers. (Toll or long distance charges may apply.)

U.S.: (562) 276-4394, 6 AM to 6 PM , Pacific Time, Monday-Friday

Canada: (905) 709-3839, 6 AM to 6 PM , Pacific Time, Monday-Friday

Days and hours of support are subject to change without notice.

Purchase supplies and accessories

You can purchase screens and other accessories from an Epson authorized reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766).

Or you can purchase online at www.epsonstore.com (U.S. sales) or

www.epson.ca (Canadian sales).

Epson and Instant Off are registered trademarks and Epson Exceed Your Vision is a registered logomark of Seiko Epson Corporation. PowerLite and PrivateLine are registered trademarks of Epson America, Inc.

General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks.

This information is subject to change without notice.

© 2008 Epson America, Inc. 7/08

Printed in XXXXXX CPD-26345

6

Adjust the image

1

To raise the image, press the foot release lever and lift the front of the projector. Release the lever to lock the foot in position.

Remote Control Map

Search and individual Source selection buttons Power button

2

Rotate the focus ring to sharpen the image. To reduce or enlarge the image, rotate the zoom ring.

Focus ring

Zoom ring

3

If your image looks like or , first make sure the projector is facing the screen squarely. Then, if necessary, press the and

buttons on the projector’s control panel until the image looks correct.

4

To select the best color mode, press the Color Mode button on the remote control. Press it repeatedly to move through the options.

A/V Mute button

Turns off image

Auto button

Resets tracking, sync, and position

Aspect button

Changes screen size

Page Up/Down buttons

Control PowerPoint ® slides

(USB cable required)

E-Zoom +/– buttons

Zoom into image details

Menu button

Accesses menus

Freeze button

Stops image

Color Mode button

Changes display mode

Num button

Activates number buttons

Help button

Displays help menus

Volume buttons

Adjust volume

Esc button

Exits menus

Menu navigation buttons and Enter button

Troubleshooting

If you see a blank screen

If you see a blank screen or the No signal message after turning on your computer or video source, check the following:

 Make sure the power light on the projector is green and not flashing and the A/V Mute slide (lens cover) is open.

 Make sure the cables are connected correctly. (See the User’s Guide for more information.)

 If you’ve connected more than one video source, you may need to press the Source Search button on the projector or the Search button on the remote control to select the one you want to watch.

(Allow a few seconds for the projector to sync up after pressing it.)

If the picture is taller on one side

The projector is set at an angle to the screen. Face it squarely toward the screen.

Aspect button Color Mode button

5

If the image is stretched or cut off, press the Aspect button until the image looks correct.

See your User’s Guide on the CD-ROM for more information about image adjustments.

7

Install User’s Guide and register your projector

1

Insert the projector CD-ROM in your drive. If the installer doesn’t open automatically, double-click the Epson CD-ROM icon, then double-click the Epson installer icon.

2

Select English.

3

Follow the instructions on the screen to register.

NOTE

You can also register at www.epson.com/webreg.

4

After you register the projector, click User’s Guide to install it.

(If you are using Windows and don’t already have Adobe ®

Reader ® , click Adobe Reader and follow the on-screen instructions to install it.)

5

When you’re done, click Exit.

To open your User’s Guide, double-click the PL HC700 User’s Guide

icon on your desktop.

Where to get help

Internet support

Visit Epson’s support website at epson.com/support and select your product for solutions to common problems. You can download utilities and documentation, get FAQs and troubleshooting advice, or e-mail Epson with your questions.

Speak to a support representative

To use the Epson PrivateLine ® Support service, call (800) 637-7661 and enter the PIN on the Epson PrivateLine Support card that came with your projector.

This service is available 6 AM to 6 PM , Pacific Time, Monday through Friday, for the duration of your warranty period. You may also speak with a projector support specialist by dialing one of the following numbers. (Toll or long distance charges may apply.)

U.S.: (562) 276-4394, 6 AM to 6 PM , Pacific Time, Monday-Friday

Canada: (905) 709-3839, 6 AM to 6 PM , Pacific Time, Monday-Friday

Days and hours of support are subject to change without notice.

Purchase supplies and accessories

You can purchase screens and other accessories from an Epson authorized reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766).

Or you can purchase online at www.epsonstore.com (U.S. sales) or

www.epson.ca (Canadian sales).

Epson and Instant Off are registered trademarks and Epson Exceed Your Vision is a registered logomark of Seiko Epson Corporation. PowerLite and PrivateLine are registered trademarks of Epson America, Inc.

General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks.

This information is subject to change without notice.

© 2008 Epson America, Inc. 7/08

Printed in XXXXXX CPD-26345

6

Adjust the image

1

To raise the image, press the foot release lever and lift the front of the projector. Release the lever to lock the foot in position.

Remote Control Map

Search and individual Source selection buttons Power button

2

Rotate the focus ring to sharpen the image. To reduce or enlarge the image, rotate the zoom ring.

Focus ring

Zoom ring

3

If your image looks like or , first make sure the projector is facing the screen squarely. Then, if necessary, press the and

buttons on the projector’s control panel until the image looks correct.

4

To select the best color mode, press the Color Mode button on the remote control. Press it repeatedly to move through the options.

A/V Mute button

Turns off image

Auto button

Resets tracking, sync, and position

Aspect button

Changes screen size

Page Up/Down buttons

Control PowerPoint ® slides

(USB cable required)

E-Zoom +/– buttons

Zoom into image details

Menu button

Accesses menus

Freeze button

Stops image

Color Mode button

Changes display mode

Num button

Activates number buttons

Help button

Displays help menus

Volume buttons

Adjust volume

Esc button

Exits menus

Menu navigation buttons and Enter button

Troubleshooting

If you see a blank screen

If you see a blank screen or the No signal message after turning on your computer or video source, check the following:

 Make sure the power light on the projector is green and not flashing and the A/V Mute slide (lens cover) is open.

 Make sure the cables are connected correctly. (See the User’s Guide for more information.)

 If you’ve connected more than one video source, you may need to press the Source Search button on the projector or the Search button on the remote control to select the one you want to watch.

(Allow a few seconds for the projector to sync up after pressing it.)

If the picture is taller on one side

The projector is set at an angle to the screen. Face it squarely toward the screen.

Aspect button Color Mode button

5

If the image is stretched or cut off, press the Aspect button until the image looks correct.

See your User’s Guide on the CD-ROM for more information about image adjustments.

7

Install User’s Guide and register your projector

1

Insert the projector CD-ROM in your drive. If the installer doesn’t open automatically, double-click the Epson CD-ROM icon, then double-click the Epson installer icon.

2

Select English.

3

Follow the instructions on the screen to register.

NOTE

You can also register at www.epson.com/webreg.

4

After you register the projector, click User’s Guide to install it.

(If you are using Windows and don’t already have Adobe ®

Reader ® , click Adobe Reader and follow the on-screen instructions to install it.)

5

When you’re done, click Exit.

To open your User’s Guide, double-click the PL HC700 User’s Guide

icon on your desktop.

Where to get help

Internet support

Visit Epson’s support website at epson.com/support and select your product for solutions to common problems. You can download utilities and documentation, get FAQs and troubleshooting advice, or e-mail Epson with your questions.

Speak to a support representative

To use the Epson PrivateLine ® Support service, call (800) 637-7661 and enter the PIN on the Epson PrivateLine Support card that came with your projector.

This service is available 6 AM to 6 PM , Pacific Time, Monday through Friday, for the duration of your warranty period. You may also speak with a projector support specialist by dialing one of the following numbers. (Toll or long distance charges may apply.)

U.S.: (562) 276-4394, 6 AM to 6 PM , Pacific Time, Monday-Friday

Canada: (905) 709-3839, 6 AM to 6 PM , Pacific Time, Monday-Friday

Days and hours of support are subject to change without notice.

Purchase supplies and accessories

You can purchase screens and other accessories from an Epson authorized reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766).

Or you can purchase online at www.epsonstore.com (U.S. sales) or

www.epson.ca (Canadian sales).

Epson and Instant Off are registered trademarks and Epson Exceed Your Vision is a registered logomark of Seiko Epson Corporation. PowerLite and PrivateLine are registered trademarks of Epson America, Inc.

General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks.

This information is subject to change without notice.

© 2008 Epson America, Inc. 7/08

Printed in XXXXXX CPD-26345