75920 Series 2D Prints

75920 Series 2D Prints
4
3
2
LOCKWASHER SEATED ON
THE INNER SURFACE OF
H
BEZEL, SEE NOTE 12
BEZEL, BLACK PLASTIC, WHITE LETTERING
SEE NOTE 12
D
1
HOUSING, BLACK PLASTIC
LOCK WASHER, 2 REQ'D
HEX NUT, BRASS,
2 REQ'D, SEE NOTE 12
HEX NUT, BRASS, 2 REQ'D
BEZEL, SEE NOTE 12
STUD, COPPER, 3/8-24, 2 PL
CAP & SCREW, SEE NOTES 12 & 13
BEZEL, SEE NOTE 12
F
KNOB, RED PLASTIC,
POINTER WHITE
SEE NOTE 12
E
B
B
1.69 [42.9]
H
2.59 [65.8]
B
0.200 [5.08]
0.450 [11.43]
1.375 [34.93]
0.900 [22.86]
0.47 [11.9]
MOUNTING STEM & PIN,
ZINC DIE CAST
NOTES:
1. ALL DIMENSIONS ARE REFERENCE ONLY
2. ALL STEEL PARTS PLATED
3. CONTACT SURFACES COPPER
4. RECOMMENDED LOCK SHANK SIZE 5/16" (0.312[7.93]) DIA
5. TESTED TO IP68
6. RATINGS:CONTINUOUS DUTY:12 Vdc: 300 AMPS;
24 Vdc: 250 AMPS; 36 Vdc: 200 AMPS
INTERMITTENT DUTY:
1000 AMPS FOR 90 SECONDS ON; 5 MINUTES OFF
2000 AMPS FOR 30 SECONDS ON; 5 MINUTES OFF
7. SWITCH MUST BE INSTALLED WITH BEZEL
8. CUSTOMER SUPPLIED TERMINALS SHOULD BE IN DIRECT
CONTACT WITH BASE OF STUD
9. MAX. STUD TORQUE 70-90 IN-LBS [7.9-10.1 N.m]
10 MOUNTING STEM HEX NUT TORQUE 18 FT LBS [24.4 N.m]
11. PANEL THICKNESS RANGE: 0.032-0.450 [0.81-11.43]
12. PARTS SHIPPED BAGGED
D 13. FOR ADDITIONAL KNOB RETENTION, ASSEMBLE SCREW
TO SHAFT THEN INSERT CAP, ASSEMBLE
SCREW TO SHAFT THEN INSERT CAP
H
NORMAL AND DOES NOT EFFECT OPERATION OR SEALING
2.28 [58.0]
MOUNTING
PATTERNS
E
0.250 [6.35]
0.750 [19.05]
0.670
[17.02]
0.812 [20.62]
0.813 [20.64]
1.000 [25.40]
A
MOUNTING STEM, 3/4-16
PERMANENT MARK
DATE CODE IN THIS AREA
0.670 [17.02]
Revision Control Record
Rev.
Description of Change
A
RELEASED DRAWING
B
ADD DATE CODE
C
ECN No.
08204
Rev.
Date
1/2/08
08362 07/08/08
08373 07/16/08
NOTE 12
D ADDED CAP & SCREW & NOTE 13 08773
4
Description of Change
ECN No.
E CORRECTED VIEW| ADDED NOTE 09280
F
G
H
CHANGED SCREWS, GASKET,
O-RING
CHANGE TO IP68
ADD CE MARK & NOTE
11268
Date
4/29/09
08/02/11
12252 08/09/12
09525 09/30/13
Tolerances Unless otherwise specifically noted, the
following are default tolerances;
2-places
+/- 0.02"
3
Angular
+/- 1
Metric: Shown in [ ] refers to equivalent English Dim Tol
"REF." or an Asterisk (*) = Non-Toleranced Reference
Dimension, shown for clarification purposes only.
NOTE: All tolerances are Non-Cumulative.
FORM CHT-6 (2/07)
12/8/08
3-places
+/- 0.005"
Used On
or Ref.:
EX28369
Special Characteristics:
PROPRIETARY INFORMATION This
Engineering Drawing, and the
Critical Characteristic, relating to
information contained herein, is
CC
Safety and/or Regulatory Compliance
proprietary to Cole Hersee Company and
may not be disclosed, re-produced, or in
Significant Characteristic relating to
X
any other way transferred or
Process Control
communicated to any other party without
Control Dimension relating to Form the express written consent of an
authorized representative of Cole Hersee KC Fit - Function as defined by Cole
Hersee Company and/or the Customer
Company.
Scale: 1:1
Drawn
By:
2
DPS
Date
Drawn:
1/2/08
Pg. 1 of 1
Cole Hersee Co.
20 Old Colony Ave., South Boston, MA, 02127
R
Description:
Drawing /
Part No.:
Phn: 617-268-2100 Web: www.colehersee.com
SW,ROT,MAST DISC
75920
1
Current Rev.
H
A
4
3
2
HOUSING, BLACK PLASTIC
LOCKWASHER SEATED ON
THE INNER SURFACE OF
BEZEL, SEE NOTE 12
C
BEZEL, BLACK PLASTIC, WHITE LETTERING
SEE NOTE 12
1
LOCK WASHER, 2 REQ'D
HEX NUT, BRASS, 2 REQ'D
HEX NUT, BRASS,
2 REQ'D, SEE NOTE 12
STUD, COPPER, 3/8-24, 2 PL
CAP & SCREW, SEE NOTES 12 & 13
KNOB, RED WITH
WHITE POINTER
NOTE 12
B
1.69 [42.9]
C
2.56 [65.0]
0.200 [5.08]
0.450 [11.43]
1.375 [34.93]
0.900 [22.86]
0.47 [11.9]
MOUNTING STEM & PIN,
ZINC DIE CAST
NOTES:
1. ALL DIMENSIONS ARE REFERENCE ONLY
2. ALL STEEL PARTS PLATED
3. CONTACT SURFACES COPPER
4. RECOMMENDED LOCK SHANK SIZE 5/16" (0.312[7.93]) DIA
5. TESTED TO IP68
6. RATINGS: CONTINUOUS DUTY:
12 Vdc: 300 AMPS; 24 Vdc: 250 AMPS; 36 Vdc: 200 AMPS
INTERMITTENT DUTY:
1000 AMPS FOR 90 SECONDS ON; 5 MINUTES OFF
2000 AMPS FOR 30 SECONDS ON; 5 MINUTES OFF
7. SWITCH MUST BE INSTALLED WITH BEZEL
8. CUSTOMER SUPPLIED TERMINALS SHOULD BE IN DIRECT
CONTACT WITH BASE OF STUD
9. STUD TORQUE 70-90 IN-LBS [7.9-10.1 N.m]
10. MOUNTING STEM HEX NUT TORQUE 18 FT LBS [24.4 N.m]
11. PANEL THICKNESS RANGE: 0.032-0.450 [0.81-11.43]
12. PARTS SHIPPED BAGGED
13. FOR ADDITIONAL KNOB RETENTION, ASSEMBLE SCREW
TO SHAFT THEN INSERT CAP
2.34 [59.5]
MOUNTING
PATTERNS
0.670
[17.02]
0.250 [6.35]
0.750 [19.05]
0.812 [20.62]
0.813 [20.64]
1.000 [25.40]
MOUNTING STEM, 3/4-16
Revision Control Record
Rev.
Rev.
Description of Change
ECN No.
Date
A
RELEASED DRAWING
11265
8/16/11
B
CHANGE TO IP68
12252 08/09/12
C
ADD CE MARK & NOTE
09529 09/30/13
Description of Change
ECN No.
Date
Tolerances Unless otherwise specifically noted, the
following are default tolerances;
2-places
+/- 0.02"
3-places
+/- 0.005"
Angular
+/- 1
Metric: Shown in [ ] refers to equivalent English Dim Tol
"REF." or an Asterisk (*) = Non-Toleranced Reference
Dimension, shown for clarification purposes only.
NOTE: All tolerances are Non-Cumulative.
FORM CHT-6 (2/07)
4
C
PERMANENT MARK
DATE CODE IN THIS AREA
0.670 [17.02]
3
Used On
or Ref.:
75920, EX28670
NORMAL AND DOES NOT EFFECT OPERATION OR SEALING
PROPRIETARY INFORMATION
This
Engineering Drawing, and the
information contained herein, is
proprietary to Cole Hersee Company and
may not be disclosed, re-produced, or in
any other way transferred or
communicated to any other party without
the express written consent of an
authorized representative of Cole Hersee
Company.
Scale: 1:1
Drawn
By:
2
A
DPS
Special Characteristics:
Cole Hersee Co.
Critical Characteristic, relating to
CC Safety and/or Regulatory Compliance
X
Significant Characteristic relating to
Process Control
Control Dimension relating to Form Fit - Function as defined by Cole
KC Hersee Company and/or the Customer
Date
Drawn:
4/6/11
Pg. 1 of 1
20 Old Colony Ave., South Boston, MA, 02127
R
Description:
Drawing /
Part No.:
Phn: 617-268-2100 Web: www.colehersee.com
SW,ROT,MAST DISC
75920-05
1
Current Rev.
C
4
3
BEZEL, BLACK PLASTIC, WHITE LETTERING
SEE NOTE 12
2
LOCKWASHER SEATED ON
THE INNER SURFACE OF
B
BEZEL, SEE NOTE 12
1
HOUSING, BLACK PLASTIC
LOCK WASHER, STAINLESS STEEL, 2 REQ'D
HEX NUT, BRASS,
2 REQ'D, SEE NOTE 12
HEX NUT, STAINLESS STEEL, 2 REQ'D
STUD, COPPER, TIN PLATED, 3/8-24, 2 PL
CAP & SCREW, SEE NOTES 12 & 13
KNOB, RED WITH
WHITE POINTER
NOTE 12
B
1.69 [42.9]
B
2.56 [65.0]
0.200 [5.08]
0.450 [11.43]
1.375 [34.93]
0.900 [22.86]
0.47 [11.9]
MOUNTING STEM & PIN,
ZINC DIE CAST
NOTES:
1. ALL DIMENSIONS ARE REFERENCE ONLY
2. ALL STEEL PARTS PLATED
3. CONTACT SURFACES COPPER
4. RECOMMENDED LOCK SHANK SIZE 5/16" (0.312[7.93]) DIA
5. TESTED TO IP68
6. RATINGS:
CONTINUOUS DUTY:
12 Vdc: 300 AMPS; 24 Vdc: 250 AMPS; 36 Vdc: 200 AMPS
INTERMITTENT DUTY:
1000 AMPS FOR 90 SECONDS ON; 5 MINUTES OFF
2000 AMPS FOR 30 SECONDS ON; 5 MINUTES OFF
7. SWITCH MUST BE INSTALLED WITH BEZEL
8. CUSTOMER SUPPLIED TERMINALS SHOULD BE IN DIRECT
CONTACT WITH BASE OF STUD
9. STUD TORQUE 70-90 IN-LBS [7.9-10.1 N.m]
10. MOUNTING STEM HEX NUT TORQUE 18 FT LBS [24.4 N.m]
11. PANEL THICKNESS RANGE: 0.032-0.450 [0.81-11.43]
12. PARTS SHIPPED BAGGED
13. FOR ADDITIONAL KNOB RETENTION, ASSEMBLE SCREW
TO SHAFT THEN INSERT CAP
2.34 [59.5]
MOUNTING
PATTERNS
0.670
[17.02]
0.250 [6.35]
0.750 [19.05]
0.812 [20.62]
0.813 [20.64]
1.000 [25.40]
MOUNTING STEM, 3/4-16
PERMANENT MARK
DATE CODE IN THIS AREA
0.670 [17.02]
Revision Control Record
Rev.
Description of Change
ECN No.
Date
Tolerances Unless otherwise specifically noted, the
following are default tolerances;
2-places
+/- 0.02"
3-places
+/- 0.005"
Angular
+/- 1
Rev.
Description of Change
ECN No.
Date
A
ADD STAINLESS STEEL
HARDWARE
12328
10/29/12
"REF." or an Asterisk (*) = Non-Toleranced Reference
Dimension, shown for clarification purposes only.
B
ADD CE MARK & NOTE
09525
09/30/13
NOTE: All tolerances are Non-Cumulative.
Metric: Shown in [ ] refers to equivalent English Dim Tol
FORM CHT-6 (2/07)
4
3
Used On
or Ref.:
75920, EX28988
B
PROPRIETARY INFORMATION
This
Engineering Drawing, and the
information contained herein, is
proprietary to Cole Hersee Company and
may not be disclosed, re-produced, or in
any other way transferred or
communicated to any other party without
the express written consent of an
authorized representative of Cole Hersee
Company.
Scale: 1:1
Drawn
By:
2
DPS
NORMAL AND DOES NOT EFFECT OPERATION OR SEALING
Special Characteristics:
Cole Hersee Co.
Critical Characteristic, relating to
CC Safety and/or Regulatory Compliance
X
Significant Characteristic relating to
Process Control
Control Dimension relating to Form Fit - Function as defined by Cole
KC Hersee Company and/or the Customer
Date
Drawn:
9/4/12
Pg. 1 of 1
20 Old Colony Ave., South Boston, MA, 02127
R
Description:
Drawing /
Part No.:
Phn: 617-268-2100 Web: www.colehersee.com
SW,ROT,MAST DISC
75920-10
1
Current Rev.
B
A
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement