INSTALLATION PARTS INCLUDED

INSTALLATION PARTS INCLUDED
INSTALLATION
MAGNUM PLUS MIRROR
1409
877.370.3604 (toll free)
PARTS INCLUDED
1
1
Magnum Plus Mirror Assembly—Large Head/Convex Lens/Long Stem
Hardware Kit, Including:
1
5/16”-18 X 1-1/2” Socket Head Cap Screw
1
5/16”-18 X 2” Socket Head Cap Screw
1
2.5mm Hex Wrench
1
5/16” Split Lock Washer
1
5/16” Internal Tooth Lock Washer
1
Double End Threaded Stud
1
1” Spacer—NOT USED
1
Installation Instructions
Please read and understand entire instructions before starting installation.
THANK YOU FOR CHOOSING KϋRYAKYN!
IN ORDER TO PROTECT YOU AND OTHERS FROM POSSIBLE INJURY AND/OR
PROPERTY DAMAGE OR LOSS, PLEASE PAY CLOSE ATTENTION TO ALL
INSTRUCTIONS, WARNINGS, CAUTIONS AND NOTICES REGARDING THE USE
AND CARE OF THIS PRODUCT.
This indication alerts you to the fact that ignoring the
contents described herein may negatively affect product
performance and functionality.
This indication alerts you to the fact that ignoring
the contents described herein can result in potential
injury.
IF INSTALLING THIS PRODUCT FOR ANOTHER PARTY,
PLEASE MAKE SURE THEY RECEIVE THIS COPY OF THE
INSTALLATION INSTRUCTIONS SO THEY ARE AWARE OF
THE IMPORTANT INFORMATION CONTAINED IN THEM.
TOOLS SUGGESTED
Set of Hex Wrenches, Set of Combination Wrenches
STRICTLY OBSERVE THE FOLLOWING GUIDELINES IN ORDER TO USE THE
PRODUCT PROPERLY AND AVOID POTENTIALLY DANGEROUS ACCIDENTS.
ALL INSTALLATIONS
STEP 1
CUSTOMER SERVICE
Read and understand all steps in the instructions before starting the
installation. Park the motorcycle on a hard, level surface and turn off the
ignition.
NOTE: The included 2.5mm Hex Wrench is used only in P/N 1428, 1430, 1437
& 1438 to adjust the swivel ball tension.
NOTE: Mirror adapters (sold separately) are required for installation on metric
cruisers.
INSTALLATION QUESTIONS
[email protected]
or call 715.247.2983
LIMITED WARRANTY
Küryakyn warrants that any Küryakyn products
sold hereunder, shall be free of defects in
materials and workmanship for a period of one
(1) year from the date of purchase by the
consumer excepting the following provisions:
● Küryakyn shall have no obligation in the event
the customer is unable to provide a receipt
showing the date the customer purchased the
product(s).
●The product must be properly installed,
maintained and operated under
normal conditions.
●Küryakyn makes no warranty, expressed or
implied, with respect to any gold plated
products.
●Küryakyn shall not be liable for any
consequential and incidental damages, including
labor and paint, resulting from failure of a
Küryakyn product, failure to deliver, delay in
delivery, delivery in nonconforming condition, or
for any breech of contract or duty between
Küryakyn and a customer.
●Küryakyn products are often intended for use in
specific applications. Küryakyn makes no
warranty if a Küryakyn product is used in
applications other than intended.
●Küryakyn electrical products are warranted for
one (1) year from the date of purchase by the
consumer. L.E.D.’S contained in components of
Küryakyn products will be warranted for defects
in materials and workmanship for 3 years from
the date of purchase where as all other
components shall be warranted for one(1) year.
This includes, but is not limited to; control
modules, wiring, chrome & other components.
●Küryakyn makes no warranty of any kind in
regard to other manufacturer¹s products
distributed by Küryakyn. Küryakyn will pass on
all warranties made by the manufacturer and
where possible, will expedite the claim on behalf
of the customer, but ultimately, responsibility for
disposition of the warranty claim lies
with the manufacturer.
ABOUT OUR CATALOG
For purchasing Küryakyn® products, you
can receive a complete catalog free of charge.
Send the Proof-of-Purchase below with
your address to: Küryakyn, P.O. Box 339,
Somerset, WI 54025.
Please indicate either Accessories Catalog for
Harley-Davidson® or GL & Metric Cruisers.
Be sure to ask your local dealer about other
Küryakyn® products, the motorcycle parts and
accessories designed for riders by riders.
©2005 Küryakyn USA® All Rights reserved.
Avoid damage to the motorcycle. Protect painted surfaces with a
soft cloth or blanket.
Ensure that the position of the mirror and stem DO NOT interfere
with the operation of the motorcycle hand controls.
1409-22MC-0113
-cont.-
It is the installer’s responsibility to ensure that all of the fasteners (including
pre-assembled) are tightened before operation of the motorcycle. Küryakyn will
not provide warranty coverage on products or components lost due to improper
installation or lack of maintenance. Periodic inspection and
maintenance are required on all fasteners.
FIG 1
STEP 2
MIRROR
Remove the stock mirror from the hand controls; set it aside, they will not
be re-used.
MOUNTING WITH SINGLE SCREW
STEP 3
Determine which of the included socket head cap screws from the
hardware kit will provide maximum thread engagement in the mirror stem
without bottoming out.
STEP 4
Place a split lock washer over the socket head cap screw and insert it in
the hole in the hand control. FIG 1
STEP 5
Place an internal lock washer over the protruding end of the socket
head cap screw.
LOCK WASHER
STEP 6
While holding the mirror in place, thread the socket head cap screw
into the bottom of the mirror stem.
SOCKET HEAD CAP SCREW
SETSCREW
INTERNAL
LOCK WASHER
HANDLEBAR CONTROL
NOTE: Ensure that the setscrew in the mirror stem does not prevent the
socket head cap screw from being installed fully. FIG 1
STEP 7
Adjust the position of the mirror stem for visibility and clearance;
tighten the socket head cap screw and then the setscrew.
FIG 2
H-D with Bottom Mounted Turn Signals—Right Side Procedure
Removing the retainer nut and/or the ball stud clamp
in the next Step will release the turn signals from the
hand controls. Secure the turn signals to prevent
damage or injury.
SETSCREW
MIRROR
DOUBLE ENDED STUD
STEP 9
Loosen and remove the retainer nut and ball stud clamp shown in FIG 2.
STEP 10
Remove the stock mirror; hold the stock turn signal to prevent it from
being damaged.
STEP 11
Screw a double ended stud into the new mirror stem; tighten and then
tighten the set screw. FIG 2
INTERNAL LOCKWASHER
HANDLEBAR CONTROL
NOTE: Ensure that the setscrew in the mirror stem does not prevent
the double ended stud from being installed fully. FIG 2
STEP 12
Place an internal lock washer over the long end of one of the
double-ended studs; insert the assembly into the mirror stem hole in
the hand control. FIG 2
STEP 13
Place a split lock washer over the protruding end of the double-ended
stud and thread the retainer nut onto the stud. FIG 2
STEP 14
Adjust the position of the mirror stem for visibility and clearance; tighten
the retaining nut.
STEP 15
Install the ball stud clamp onto the retainer nut; adjust the turn signal and tighten the clamp.
STEP 16
Adjust the mirrors for proper view before riding the motorcycle.
LOCKWASHER
RETAINER NUT
BALL STUD CLAMP
BALL STUD
LOCK NUT
STOCK TURN SIGNAL
PAGE
2
Ride On!
MAGNUM PLUS MIRROR
INSTALLATION
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement