Motherboard
P5S800-VM
E2419
Revised Edition V4
January 2006
Copyright © 2006 ASUSTeK COMPUTER INC. All Rights Reserved.
No part of this manual, including the products and software described in it, may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language in any form
or by any means, except documentation kept by the purchaser for backup purposes, without the
express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
Product warranty or service will not be extended if: (1) the product is repaired, modified or
altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2)
the serial number of the product is defaced or missing.
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER
EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES
OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE
LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES
(INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE
OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR
ERROR IN THIS MANUAL OR PRODUCT.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED
FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME
WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS.
ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR
INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS
AND SOFTWARE DESCRIBED IN IT.
Products and corporate names appearing in this manual may or may not be registered
trademarks or copyrights of their respective companies, and are used only for identification or
explanation and to the owners’ benefit, without intent to infringe.
ii
Contents
Notices ................................................................................................ vi
Safety information ............................................................................. vii
About this guide ............................................................................... viii
Typography ......................................................................................... ix
P5S800-VM specifications summary ................................................... x
Chapter 1: Product introduction
1.1
Welcome! .............................................................................. 1-2
1.2
Package contents ................................................................. 1-2
1.3
Special features .................................................................... 1-3
1.3.1
Product highlights ................................................... 1-3
1.3.2
Innovative ASUS features ....................................... 1-4
1.4
Before you proceed .............................................................. 1-5
1.5
Motherboard overview .......................................................... 1-6
1.6
1.7
1.8
1.5.1
Placement direction ................................................ 1-6
1.5.2
Screw holes ............................................................ 1-6
1.5.3
Motherboard layout ................................................ 1-7
Central Processing Unit (CPU) .............................................. 1-8
1.6.1
Installling the CPU ................................................... 1-8
1.6.2
Installling the CPU heatsink and fan ..................... 1-11
1.6.3
Uninstallling the CPU heatsink and fan ................. 1-13
System memory ................................................................. 1-15
1.7.1
Overview ............................................................... 1-15
1.7.2
DDR Qualified Vendors List ................................... 1-15
1.7.3
Installing a DIMM ................................................... 1-17
1.7.4
Removing a DIMM ................................................. 1-17
Expansion slots ................................................................... 1-18
1.8.1
Installing an expansion card .................................. 1-18
1.8.2
Configuring an expansion card .............................. 1-18
1.8.3
Interrupt assignments .......................................... 1-19
1.8.4
PCI slots ................................................................ 1-20
1.8.5
AGP slot ................................................................ 1-20
1.9
Jumpers .............................................................................. 1-21
1.10
Connectors ......................................................................... 1-22
1.10.1 Rear panel connectors .......................................... 1-22
1.10.2 Internal connectors ............................................... 1-24
iii
Contents
Chapter 2: BIOS setup
2.1
2.2
2.3
2.4
2.5
iv
Managing and updating your BIOS ........................................ 2-2
2.1.1
Creating a bootable floppy disk .............................. 2-2
2.1.2
ASUS EZ Flash utility .............................................. 2-3
2.1.3
AFUDOS utility ........................................................ 2-4
2.1.4
ASUS CrashFree BIOS 2 utility ................................ 2-6
2.1.5
ASUS Update utility ................................................ 2-8
BIOS setup program ........................................................... 2-11
2.2.1
BIOS menu screen ................................................. 2-12
2.2.2
Menu bar ............................................................... 2-12
2.2.3
Navigation keys .................................................... 2-12
2.2.4
Menu items ........................................................... 2-13
2.2.5
Sub-menu items ................................................... 2-13
2.2.6
Configuration fields .............................................. 2-13
2.2.7
Pop-up window ..................................................... 2-13
2.2.8
Scroll bar .............................................................. 2-13
2.2.9
General help .......................................................... 2-13
Main menu .......................................................................... 2-14
2.3.1
System Time ......................................................... 2-14
2.3.2
System Date ......................................................... 2-14
2.3.3
Legacy Diskette A ................................................ 2-14
2.3.4
Primary and Secondary IDE Master/Slave ............. 2-15
2.3.5
OnChip SATA Controller ....................................... 2-16
2.3.6
System Information .............................................. 2-16
Advanced menu .................................................................. 2-17
2.4.1
JumperFree Configuration .................................... 2-17
2.4.2
CPU Configuration ................................................. 2-18
2.4.3
Chipset ................................................................. 2-19
2.4.4
Onboard Devices Configuration ............................ 2-20
2.4.5
PCI PnP ................................................................. 2-22
2.4.6
USB Configuration ................................................. 2-23
2.4.7
Instant Music Configuration .................................. 2-24
Power menu ........................................................................ 2-25
2.5.1
Suspend Mode ...................................................... 2-25
2.5.2
ACPI 2.0 Support .................................................. 2-25
Contents
2.6
2.7
2.5.3
ACPI APIC Support ................................................ 2-25
2.5.4
APM Configuration ................................................ 2-26
2.5.5
Hardware Monitor ................................................. 2-27
Boot menu .......................................................................... 2-29
2.6.1
Boot Device Priority .............................................. 2-29
2.6.2
Disk Drives ............................................................ 2-29
2.6.3
Boot Settings Configuration ................................. 2-30
2.6.4
Security ................................................................ 2-31
Exit menu ........................................................................... 2-33
Chapter 3: Software support
3.1
Installing an operating system ............................................. 3-2
3.2
Support CD information ........................................................ 3-2
3.2.1
Running the support CD ......................................... 3-2
3.2.2
Drivers menu .......................................................... 3-3
3.2.3
Utilities menu .......................................................... 3-4
3.2.4
ASUS Contact information ...................................... 3-5
v
Notices
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
• This device may not cause harmful interference, and
• This device must accept any interference received including interference
that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with
manufacturer’s instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
The use of shielded cables for connection of the monitor to the graphics
card is required to assure compliance with FCC regulations. Changes or
modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate
this equipment.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus set out in the Radio Interference
Regulations of the Canadian Department of Communications.
This class B digital apparatus complies with Canadian
ICES-003.
vi
Safety information
Electrical safety
• To prevent electrical shock hazard, disconnect the power cable from
the electrical outlet before relocating the system.
• When adding or removing devices to or from the system, ensure that
the power cables for the devices are unplugged before the signal cables
are connected. If possible, disconnect all power cables from the existing
system before you add a device.
• Before connecting or removing signal cables from the motherboard,
ensure that all power cables are unplugged.
• Seek professional assistance before using an adapter or extension cord.
These devices could interrupt the grounding circuit.
• Make sure that your power supply is set to the correct voltage in your
area. If you are not sure about the voltage of the electrical outlet you
are using, contact your local power company.
• If the power supply is broken, do not try to fix it by yourself. Contact a
qualified service technician or your retailer.
Operation safety
• Before installing the motherboard and adding devices on it, carefully read
all the manuals that came with the package.
• Before using the product, make sure all cables are correctly connected
and the power cables are not damaged. If you detect any damage,
contact your dealer immediately.
• To avoid short circuits, keep paper clips, screws, and staples away from
connectors, slots, sockets and circuitry.
• Avoid dust, humidity, and temperature extremes. Do not place the
product in any area where it may become wet.
• Place the product on a stable surface.
• If you encounter technical problems with the product, contact a qualified
service technician or your retailer.
vii
About this guide
This user guide contains the information you need when installing and
configuring the motherboard.
How this guide is organized
This manual contains the following parts:
•
Chapter 1: Product introduction
This chapter describes the features of the motherboard and the new
technology it supports. This chapter also lists the hardware setup
procedures that you have to perform when installing system
components. It includes description of the jumpers and connectors on
the motherboard.
•
Chapter 2: BIOS setup
This chapter tells how to change system settings through the BIOS
Setup menus. Detailed descriptions of the BIOS parameters are also
provided.
•
Chapter 3: Software support
This chapter describes the contents of the support CD that comes
with the motherboard package.
Where to find more information
Refer to the following sources for additional information and for product
and software updates.
viii
1.
ASUS websites
The ASUS website provides updated information on ASUS hardware
and software products. Refer to the ASUS contact information.
2.
Optional documentation
Your product package may include optional documentation, such as
warranty flyers, that may have been added by your dealer. These
documents are not part of the standard package.
Conventions used in this guide
To make sure that you perform certain tasks properly, take note of the
following symbols used throughout this manual.
D A N G E R / W A R N I N G : Information to prevent injury to yourself
when trying to complete a task.
C A U T I O N : Information to prevent damage to the components
when trying to complete a task.
I M P O R T A N T : Instructions that you MUST follow to complete a
task.
N O T E : Tips and additional information to help you complete a
task.
Typography
Bold text
Indicates a menu or an item to select
Italics
Used to emphasize a word or a phrase
<Key>
Keys enclosed in the less-than and greater-than sign means
that you must press the enclosed key
Example: <Enter> means that you must press the Enter or
Return key
<Key1+Key2+Key3>
If you must press two or more keys simultaneously, the
key names are linked with a plus sign (+)
Example: <Ctrl+Alt+D>
Command
Means that you must type the command exactly as shown,
then supply the required item or value enclosed in
brackets
Example: At the DOS prompt, type the command line:
afudos /i[filename]
afudos /iP5S800VM.ROM
ix
P5S800-VM specifications summary
CPU
LGA775 socket for Intel® Pentium® 4/CeleronD processor
Compatible with the Intel® PCG 04A and 04B processors
Supports Intel® Hyper-Threading Technology
Chipset
Northbridge: SIS 661FX
Southbridge: SIS 964
Front Side Bus
800/533 MHz
Memory
2 x 184-pin DIMM sockets support up to 2GB of
unbufferred non-ECC 400/333/266 MHz DDR DIMMs
Expansion slots
1 x AGP 8x (1.5V only)
3 x PCI slots
Storage
2 x Ultra DMA 133/100/66/33
2 x Serial ATA with RAID 0 and RAID 1 configuration
Audio
Realtek® ALC655 6-channel CODEC
S/PDIF out interface support
Universal Audio Jack (UAJ®) Sensing Technology support
LAN
Realtek® 10/100 Mbps Ethernet controller
USB
Supports up to 8 USB 2.0 ports
Special features
Power Loss Restart
ASUS AI Audio
ASUS EZ Flash
ASUS CrashFree BIOS 2
ASUS MyLogo2™
Instant Music Lite
Rear panel
1 x Parallel port
1 x LAN (RJ-45) port
4 x USB 2.0 ports
1 x VGA port
1 x Serial port (COM)
1 x PS/2 keyboard port
1 x PS/2 mouse port
Audio I/O ports
BIOS features
4 Mb Flash ROM, AMI BIOS, PnP, WfM2.0, DMI2.0,
SM BIOS 2.3, ASUS EZ Flash, CrashFree BIOS2, C.P.R.
(CPU Parameter Recall)
I n d u s t r y s t a n d a r d PCI 2.2, USB 2.0
Manageability
WfM 2.0, DMI 2.0, WOL by PME, WOR by PME, Chassis
Intrussion
(continued on the next page)
x
P5S800-VM specifications summary
Internal
connectors
2 x USB 2.0 connectors for 4 additional USB 2.0 ports
1 x CPU fan connector
1 x Chassis fan connector
1 x 20-pin ATX power connector
1 x 4-pin ATX 12 V power connector
1 x 3-1 pin Power LED connector
1 x 4-pin Speaker out connector
1 x CD/AUX connector
1 x Chassis intrusion connector
1 x Front panel audio connector
1 x S/PDIF out connector
1 x Front panel connector
Power
Requirement
ATX power supply (with 20-pin and 4-pin 12 V plugs)
Form Factor
ATX form factor: 9.6 in x 9.6 in (24.4 cm x 24.4 cm)
Support CD
contents
Device drivers
ASUS PC Probe
ASUS Live Update utility
Anti-virus software (OEM version)
*Specifications are subject to change without notice.
xi
xii
This chapter describes the motherboard
features and the new technologies
it supports.
1
Product
introduction
ASUS P5S800-VM
1-1
1.1
Welcome!
T h a n k y o u f o r b u y i n g a n A S U S® P 5 S 8 0 0 - V M m o t h e r b o a r d !
The motherboard delivers a host of new features and latest technologies,
making it another standout in the long line of ASUS quality motherboards!
Before you start installing the motherboard, and hardware devices on it,
check the items in your package with the list below.
1.2
Package contents
Check your motherboard package for the following items.
Motherboard
ASUS P5S800-VM motherboard
Cables
2 x Serial ATA signal cables
1 x Ultra DMA/133 cables
1 x Floppy disk drive cable
Accessories
I/O shield
Application CDs
ASUS motherboard support CD
Documentation
User guide
If any of the above items is damaged or missing, contact your retailer.
1.3
Special features
1.3.1
Product highlights
Latest processor technology
The motherboard comes with a 775-pin surface mount Land Grid Array
(LGA) socket designed for the Intel® Pentium® 4 processor in the 775-land
package. The motherboard supports the Intel® Pentium® 4 processor with
800 MHz Front Side Bus (FSB), 1 MB L2 cache, and core speed of up to
3.6 GHz. The motherboard also supports the Intel ® Hyper-Threading
Technology and is fully compatible with Intel® 04B and 04A processors.
See page 1-8 for details.
1-2
Chapter 1: Product introduction
SIS Advanced HyperStreaming™ Architecture
The motherboard supports the SIS HyperStreaming™ technology that
smartly manages data streaming between the Northbridge and
Southbridge, memory, graphics interface, and other peripherals for efficient
and superior performance.
SIS Ultra-AGPII™ Technology
Outstanding graphics performance is achieved with the Ultra-AGPII™
technology that enables a VGA throughput of 3.2GB/s with DDR400
significantly increasing the 2.1GB/s speed provided by AGP8X.
Serial ATA technology
The motherboard supports the Serial ATA technology through the Serial ATA
interfaces and the SIS 964 chipset. The SATA specification allows for
thinner, more flexible cables with lower pin count, reduced voltage
requirement, and up to 150 MB/s data transfer rate. See page 1-25 for
details.
Onboard RAID solution
The onboard SIS 964 chipset allows RAID 0 or RAID 1 configuration for two
SATA connectors.
AI Audio
The motherboard comes with the Realtek® ALC655 audio CODEC that lets
you enjoy high-quality 6-channel audio without having to buy advanced
sound cards. It also features intelligent detection of plugged peripherals
into the audio ports and identifies any incompatible devices. See page 1-23
for details.
S/PDIF digital sound ready
The motherboard supports the S/PDIF Out function through the S/PDIF
interfaces at midboard. The S/PDIF technology turns your computer into a
high-end entertainment system with digital connectivity to powerful audio and
speaker systems. See page 1-26 for details.
USB 2.0 technology
The motherboard implements the Universal Serial Bus (USB) 2.0
specification, dramatically increasing the connection speed from the
12 Mbps bandwidth on USB 1.1 to a fast 480 Mbps on USB 2.0. USB 2.0 is
backward compatible with USB 1.1. See page 1-28 for details.
ASUS P5S800-VM
1-3
Temperature, fan, and voltage monitoring
The CPU temperature is monitored by the ASIC (integrated in the Winbond
Super I/O) to prevent overheating and damage. The system fan rotations
per minute (RPM) is monitored for timely failure detection. The ASIC
monitors the voltage levels to ensure stable supply of current for critical
components. See page 2-27 for details.
1.3.2
Innovative ASUS features
CrashFree BIOS 2
This feature allows you to restore the original BIOS data from the support CD
in case when the BIOS codes and data are corrupted. This protection
eliminates the need to buy a replacement ROM chip. See details on page 2-6.
ASUS MyLogo2™
This new feature present in the motherboard allows you to personalize and
add style to your system with customizable boot logos. See page 2-31.
ASUS EZ Flash BIOS
With the ASUS EZ Flash, you can easily update the system BIOS even
before loading the operating system. No need to use a DOS-based utility or
boot from a floppy disk. See page 2-3 for details.
Instant Music Lite
This unique feature allows you to playback audio CDs even without booting
the system to Windows®. Just press the ASUS Instant Music special
function keys and enjoy the music! See page 2-25.
1-4
Chapter 1: Product introduction
1.4
Before you proceed
Take note of the following precautions before you install motherboard
components or change any motherboard settings.
•
Unplug the power cord from the wall socket before touching any
component.
•
Use a grounded wrist strap or touch a safely grounded object or to
a metal object, such as the power supply case, before handling
components to avoid damaging them due to static electricity
•
Hold components by the edges to avoid touching the ICs on them.
•
Whenever you uninstall any component, place it on a grounded
antistatic pad or in the bag that came with the component.
•
Before you install or remove any component, ensure
that the ATX power supply is switched off or the
p o w e r c o r d i s d e t a c h e d f r o m t h e p o w e r s u p p l y . Failure
to do so may cause severe damage to the motherboard, peripherals,
and/or components.
Onboard LED
®
P5S800-VM
The motherboard comes with a standby power LED that lights up to
indicate that the system is ON, in sleep mode, or in soft-off mode.
This is a reminder that you should shut down the system and unplug
the power cable before removing or plugging in any motherboard
component. The illustration below shows the location of the onboard
LED.
SB_PWR1
ON
Standby
Power
OFF
Powered
Off
P5S800-VM Onboard LED
ASUS P5S800-VM
1-5
1.5
Motherboard overview
Before you install the motherboard, study the configuration of your chassis
to ensure that the motherboard fits into it.
Make sure to unplug the power cord before installing or removing the
motherboard. Failure to do so can cause you physical injury and damage
motherboard components.
1.5.1
Placement direction
When installing the motherboard, make sure that you place it into the
chassis in the correct orientation. The edge with external ports goes to the
rear part of the chassis as indicated in the image below.
1.5.2
Screw holes
Place eight (8) screws into the holes indicated by circles to secure the
motherboard to the chassis.
Do not overtighten the screws! Doing so can damage the motherboard.
1-6
®
P5S800-VM
Place this side towards
the rear of the chassis
Chapter 1: Product introduction
1.5.3
Motherboard layout
PS/2KBMS KBPWR1
T: Mouse
B: Keyboard
Super
I/O
ATX12V1
COM1
LGA775
Intel FWH
4Mb
FLOPPY1
ATXPWR1
SEC_IDE1
PRI_IDE1
Top:Line In
Center:Line Out
Below:Mic In
®
SiS
661FX
LAN_USB34
P5S800-VM
F_USB12
DDR DIMM2 (64 bit,184-pin module)
VGA1
DDR DIMM1 (64 bit,184-pin module)
PARALLEL PORT
CPU_FAN1
AGP1
RTL8100C
CR2032 3V
Lithium Cell
CMOS Power
PCI1
SB_PWR1
SiS
964
SATA2
SATA1
CHA_FAN1
PCI3
ALC655
CHASSIS1
USB56
FP_AUDIO
AUX1
ASUS P5S800-VM
CD1
SPDIF1
CLRTC1
PLED1
IR_CON1
PCI2
USB78
F_PANEL
COM2
GAME1 SPEAKER1
1-7
1.6
Central Processing Unit (CPU)
The motherboard comes with a surface mount LGA775 socket designed for
the Intel® Pentium® 4 processor in the 775-land package.
1.6.1
•
Your boxed Intel® Pentium® 4 LGA775 processor package should
come with installation instructions for the CPU, fan and heatsink
assembly. If the instructions in this section do not match the CPU
documentation, follow the latter.
•
Upon purchase of the motherboard, make sure that the PnP cap is
on the socket and the socket pins are not bent. Contact your
retailer immediately if the PnP cap is missing, or if you see any
damage to the PnP cap/socket pins/motherboard components.
ASUS will shoulder the cost of repair only if the damage is shipment/
transit-related.
•
Keep the cap after installing the motherboard. ASUS will process
Return Merchandise Authorization (RMA) requests only if the
motherboard comes with the cap on the LGA775 socket.
•
The product warranty does not cover damage to the socket pins
resulting from incorrect CPU installation/removal, or misplacement/
loss/incorrect removal of the PnP cap.
Installling the CPU
To install a CPU:
®
Locate the CPU socket on the motherboard.
P5S800-VM
1.
P5S800-VM CPU Socket 775
Before installing the CPU, make sure that the socket box is facing
towards you and the load lever is on your left.
1-8
Chapter 1: Product introduction
2.
Press the load lever with your thumb (A) and move it to the left (B)
until it is released from the retention tab.
PnP Cap
Retention tab
A
Load lever
B
This side of the cam
box should face you.
To prevent damage to the socket pins, do not remove the PnP cap
unless you are installing a CPU.
3.
Lift the load lever in the direction
of the arrow to a 135º angle.
4.
Lift the load plate with your
thumb and forefinger to a 100º
angle (A), then push the PnP cap
from the load plate window to
remove (B).
B
A
Load plate
5.
Position the CPU over the
socket, making sure that
the gold triangle is on
the bottom-left corner of
the socket. The socket
alignment key should fit
into the CPU notch.
Alignment key
Gold triangle mark
ASUS P5S800-VM
1-9
6.
Close the load plate (A), then
push the load lever (B) until it
snaps into the retention tab.
A
B
The CPU fits in only one correct orientation. DO NOT force the CPU into
the socket to prevent bending the connectors on the socket and
damaging the CPU!
Notes on Intel® Hyper-Threading Technology
•
This motherboard supports Intel® Pentium® 4 CPUs in the 775-land
package with Hyper-Threading Technology.
•
Hyper-Threading Technology is supported under Windows® XP/2003
Server and Linux 1.7.x (kernel) and later versions only. Under Linux,
use the Hyper-Threading compiler to compile the code. If you are
using any other operating systems, disable the Hyper-Threading
Technology item in the BIOS to ensure system stability and
performance.
•
Installing Windows® XP Service Pack 1 or later is recommended.
•
Make sure to enable the Hyper-Threading Technology item in BIOS
before installing a supported operating system.
•
For more information on Hyper-Threading Technology, visit
www.intel.com/info/hyperthreading.
To use the Hyper-Threading Technology on this motherboard:
1.
Install an Intel® Pentium® 4 CPU in the 775-land package that supports
Hyper-Threading Technology.
2.
Power up the system and enter the BIOS Setup (see Chapter 2: BIOS
setup). Under the Advanced Menu, make sure that the item
Hyper-Threading Technology is set to Enabled. The item appears only
if you installed a CPU that supports Hyper-Threading Technology.
3.
Reboot the computer.
1-10
Chapter 1: Product introduction
1.6.2
Installling the CPU heatsink and fan
The Intel® Pentium® 4 LGA775 processor requires a specially designed
heatsink and fan assembly to ensure optimum thermal condition and
performance.
•
Install the motherboard to the chassis before you install the CPU fan
and heatsink assembly
•
When you buy a boxed Intel® Pentium® 4 processor, the package
includes the CPU fan and heatsink assembly. If you buy a CPU
separately, make sure that you use only Intel®-certified
multi-directional heatsink and fan.
•
Your Intel® Pentium® 4 LGA775 heatsink and fan assembly comes in
a push-pin design and requires no tool to install.
If you purchased a separate CPU heatsink and fan assembly, make sure
that a Thermal Interface Material is properly applied to the CPU heatsink
or CPU before you install the heatsink and fan assembly.
To install the CPU heatsink and fan:
1.
Place the heatsink on top of the
installed CPU, making sure that
the four fasteners match the
holes on the motherboard.
Fastener
Motherboard hole
Make sure each fastener is oriented as shown, with the narrow groove
directed outward.
ASUS P5S800-VM
1-11
2.
3.
Push down two fasteners at a
time in a diagonal sequence to
secure the heatsink and fan
assembly in place.
A
B
B
A
B
A
A
B
When the fan and heatsink assembly is in place, connect the CPU fan
cable to the connector on the motherboard labeled CPU_FAN1.
®
P5S800-VM
CPU_FAN1
CPU FAN PWM
CPU FAN IN
CPU FAN PWR
GND
P5S800-VM CPU fan connector
Do not forget to connect the CPU fan connector! Hardware monitoring
errors can occur if you fail to plug this connector.
1-12
Chapter 1: Product introduction
1.6.3
Uninstalling the CPU heatsink and fan
To uninstall the CPU heatsink and fan:
1.
Disconnect the CPU fan
cable from the connector
on the motherboard labeled
CPU_FAN1.
2.
Rotate each fastener
counterclockwise.
3.
Pull up two fasteners at a
time in a diagonal sequence
to disengage the heatsink
and fan assembly from the
motherboard.
B
A
A
B
A
B
B
A
ASUS P5S800-VM
1-13
4.
Remove the heatsink and fan
assembly from the
motherboard.
5.
Rotate each fastener
clockwise to reset the
orientation.
Narrow end of the groove
The narrow end of the
groove should point
outward after resetting.
(The photo shows the
groove shaded for
emphasis.)
1-14
Chapter 1: Product introduction
1.7
System memory
1.7.1
Overview
The motherboard comes with two 184-pin Double Data Rate (DDR) Dual
Inline Memory Modules (DIMM) sockets. You may install 128 MB, 256 MB,
512 MB and 1 GB unbuffered non-ECC DDR DIMMs into the DIMM sockets.
DIMM2
®
P5S800-VM
DIMM1
The following figure illustrates the location of the sockets:
P5S800-VM 184-pin DDR DIMM sockets
1.7.2
DDR Qualified Vendors List
The following table lists the memory modules that have been tested and
qualified for use with this motherboard. Visit the ASUS website
(www.asus.com) for the latest DDR DIMM modules for this motherboard.
DDR Qualified Vendors List
Size
256MB
256MB
512MB
512MB
512MB
512MB
256MB
256MB
512MB
256MB
512MB
512MB
256MB
256MB
512MB
256MB
512MB
256MB
Vendor
Kingston
Kingston
Kingston
Kingston
Kingston
Kingston
Kingston
Infineon
Infineon
Infineon
Infineon
HY
HY
HY
HY
Corsair
Corsair
Corsair
Model
KVR333X64C25/256
KVR333X64C25/256
KVR333X64C25/512
KVR333X64C25/512
KVR400X643A/512
KVR400X64C3A/512
KVR400X64C3A/256
HYS64D64320GU-5-C
HYS64D32300GU-5-C
HYS64D64320GU-5-C
HYS64D64320GU-6-C
DDR400-512
DDR266-256
DDR333-256
DDR333-512
VS256MB400
VS512MB400
VS256MB333
DIMM support
Brand
Component
A B
Side(s)
Kingston
SS
D3208DH1T-6
• •
Hynix
SS
HY5DU56822BT-J
• •
Hynix
DS
HY5DU56822BT-D43
• •
Hynix
DS
HY5DU56822BT-J
• •
Hynix
DS
HY5DU56822BT-D43
• •
Kingston
DS
D3208DL3T-5
• •
Hynix
SS
HY5DU56822BT-D43
• •
Infineon
SS
HYB25D256800CE-5C
• •
Infineon
DS
HYB25D256800CE-5C
• •
Infineon
SS
HYB25D256800CE-5C
• •
Infineon
DS
HYB25D256800CE-6C
• •
Hynix
DS
HY5DU56822BT-D43
• •
Hynix
SS
HY5DU56822AT-H
• •
Hynix
SS
HY5DU56822BT-J
• •
Hynix
DS
HY5DU56822BT-J
• •
Value select
SS
VS32M8-5 2B0409
• •
Value select
DS
VS32M8-5 2B0412
• •
Samsung
SS
K4H5608380-TCB3
• •
(Continued on the next page)
ASUS P5S800-VM
1-15
DDR Qualified Vendors List
Side(s)
Component
DS
MT46V32M8-G
DIMM support
A B
Size
512MB
Vendor
Micron
Model
MT16VDDT6464AG-335GB
Brand
Micron
256MB
Micron
MT8VDDT3264AG-335GB
Micron
SS
256MB
Micron
MT8VDDT3264AG-40BGB
Micron
SS
256MB
Samsung
M368L3223FTN-CB3
Samsung
512MB
256MB
Samsung
Winbond
M368L6423FTN-CB3
U24256ADWBG6H20
Samsung
Winbond
256MB
Winbond
U24256AAWBG6H20
Winbond
512MB
Winbond
DDR333-512
Winbond
256MB
Transcend
DDR400-256
Mosel
SS
V58C2256804SAT5B
•
•
512MB
256MB
512MB
512MB
256MB
256MB
256MB
512MB
512MB
1G
256MB
Transcend
Transcend
Transcend
Kingmax
Apacer
Apacer
Apacer
Apacer
Smart
Twinmos
Twinmos
DDR400-512
DDR333-256
DDR333-512
MPXC22D-38KT3R
77.10628.10A
77.10628.56G
77.10636.56G
77.10736.11G
U24512ADSRG6H20
M2S5016AJAMC5G0811A-J
M2S9109BFAPS9F0811A-T
Samsung
Mosel
Hynix
Kingmax
Apacer
Mosel
Mosel
Infineon
Smart
Micron
PSC
DS
SS
DS
DS
SS
SS
SS
DS
DS
DS
SS
K4H560838F-TCCC
V58C2256804SAT6
HY5DU56822CT-J
KDL388P4EA-50
AM3A5608AIT-6B
V58C2256804SAT6
V58C2256804SAT5B
HYB25D256800BT-5B
D32M8XS50H3X4AMV
MT46V64M8TG-6T
A2S56D30ATP
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
MT46V32M8-G
•
•
MT46V32M8-G
•
•
SS
K4H560838F-TCB3
•
•
DS
SS
K4H5608838F-TCB3
W942508CH-5
•
•
•
•
SS
W942508CH-6
•
•
DS
W942508BH-6
•
•
Legend:
S i d e ( s ) : S S - Single-sided
D S - Double-sided
DIMM support:
A - supports one module inserted into either slot, in a Single-channel memory
configuration.
B -
1-16
supports one pair of modules inserted into both slots.
Chapter 1: Product introduction
1.7.3
Installing a DIMM
Make sure to unplug the power supply before adding or removing DIMMs
or other system components. Failure to do so may cause severe damage
to both the motherboard and the components.
2
1.
Unlock a DIMM socket by
pressing the retaining clips
outward.
2.
Align a DIMM on the socket such
that the notch on the DIMM
matches the break on the
socket.
DDR DIMM notch
1
1
Unlocked retaining clip
A DDR DIMM is keyed with a notch so that it fits in only one direction.
DO NOT force a DIMM into a socket to avoid damaging the DIMM.
3.
Firmly insert the DIMM into the
socket until the retaining clips
snap back in place and the DIMM
is properly seated.
Locked Retaining Clip
1.7.4
Removing a DIMM
2
Follow these steps to remove a DIMM.
1.
Simultaneously press the
retaining clips outward to unlock
the DIMM.
1
1
DDR DIMM notch
Support the DIMM lightly with your fingers when pressing the retaining
clips. The DIMM might get damaged when it flips out with extra force.
2.
Remove the DIMM from the socket.
ASUS P5S800-VM
1-17
1.8
Expansion slots
In the future, you may need to install expansion cards. The following
sub-sections describe the slots and the expansion cards that they support.
Make sure to unplug the power cord before adding or removing
expansion cards. Failure to do so may cause you physical injury and
damage motherboard components.
1.8.1
Installing an expansion card
To install an expansion card:
1.
Before installing the expansion card, read the documentation that
came with it and make the necessary hardware settings for the card.
2.
Remove the system unit cover (if your motherboard is already
installed in a chassis).
3.
Remove the bracket opposite the slot that you intend to use. Keep
the screw for later use.
4.
Align the card connector with the slot and press firmly until the card is
completely seated on the slot.
5.
Secure the card to the chassis with the screw you removed earlier.
6.
Replace the system cover.
1.8.2
Configuring an expansion card
After installing the expansion card, configure it by adjusting the software
settings.
1.
Turn on the system and change the necessary BIOS settings, if any.
See Chapter 2 for information on BIOS setup.
2.
Assign an IRQ to the card. Refer to the tables on the next page.
3.
Install the software drivers for the expansion card.
1-18
Chapter 1: Product introduction
1.8.3
Interrupt assignments
Standard interrupt assignments
IRQ
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Priority
Standard Function
1
2
•
11
12
13
14
15
3
4
5
6
7
8
9
10
System Timer
Keyboard Controller
Re-direct to IRQ#9
Communications Port (COM2)*
Communications Port (COM1)*
IRQ holder for PCI steering*
Floppy Disk Controller
Printer Port (LPT1)*
System CMOS/Real Time Clock
IRQ holder for PCI steering*
IRQ holder for PCI steering*
IRQ holder for PCI steering*
PS/2 Compatible Mouse Port*
Numeric Data Processor
Primary IDE Channel
Secondary IDE Channel
* These IRQs are usually available for ISA or PCI devices.
IRQ assignments for this motherboard
A
PCI slot 1
PCI slot 2
PCI slot 3
AGP 8X slot
Onboard USB controller 1
Onboard USB controller 2
Onboard USB controller 3
Onboard USB controller 4
Onboard USB 2.0 controller
Onboard LAN
Onboard audio
Onboard VGA
B
—
—
—
shared
—
—
shared
—
—
—
—
—
—
—
shared
—
—
—
—
shared
shared
—
shared
—
C
D
E
F
—
—
—
—
—
—
used
—
—
—
—
—
—
—
—
—
—
used
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
used
—
—
—
—
—
—
—
—
—
G
H
used
—
—
—
—
—
—
—
—
shared
—
—
—
—
—
—
—
shared
—
—
—
—
—
—
When using PCI cards on shared slots, ensure that the drivers support
“Share IRQ” or that the cards do not need IRQ assignments. Otherwise,
conflicts will arise between the two PCI groups, making the system
unstable and the card inoperable.
ASUS P5S800-VM
1-19
1.8.4
PCI slots
The PCI slots support cards such as a
LAN card, SCSI card, USB card, and
other cards that comply with PCI
specifications. The figure shows a
LAN card installed on a PCI slot.
1.8.5
AGP slot
The Accelerated Graphics Port (AGP) slot supports AGP8X/4X cards. When
you buy an AGP card, make sure that you ask for one with +1.5V
specification. Note the notches on the card golden fingers to ensure that
they fit the AGP slot on your motherboard.
®
P5S800-VM
Install only 1.5 V or 0.8 V AGP cards on this motherboard! 3.3V AGP
cards are not supported in this motherboard.
Keyed for 1.5v
P5S800-VM Accelerated Graphics Port (AGP)
1-20
Chapter 1: Product introduction
1.9
1.
Jumpers
Clear RTC RAM (CLRTC1)
This jumper allows you to clear the Real Time Clock (RTC) RAM in
CMOS. You can clear the CMOS memory of date, time, and system
setup parameters by erasing the CMOS RTC RAM data. The onboard
button cell battery powers the RAM data in CMOS, which include
system setup information such as system passwords.
To erase the RTC RAM:
1.
Turn OFF the computer and unplug the power cord.
2.
Remove the onboard battery.
3.
Move the jumper cap from pins 2-3 (default) to pins 1-2. Keep the
cap on pins 1-2 for about 5~10 seconds, then move the cap back to
pins 2-3.
4.
Re-install the battery.
5.
Plug the power cord and turn ON the computer.
6.
Hold down the <Del> key during the boot process and enter BIOS
setup to re-enter data.
®
P5S800-VM
Except when clearing the RTC RAM, never remove the cap on CLRTC
jumper default position. Removing the cap will cause system boot failure!
CLRTC1
2
1
Clear CMOS
P5S800-VM Clear RTC RAM
3
2
Normal
(Default)
You do not need to clear the RTC when the system hangs due to
overclocking. For system failure due to overclocking, use the C.P.R. (CPU
Parameter Recall) feature. Shut down and reboot the system so the BIOS
can automatically reset parameter settings to default values.
ASUS P5S800-VM
1-21
2.
Keyboard power (3-pin KBPWR1)
This jumper allows you to enable or disable the keyboard wake-up
feature. Set this jumper to pins 2-3 (+5VSB) to wake up the
computer when you press a key on the keyboard (the default is the
Space Bar). This feature requires an ATX power supply that can supply
at least 1A on the +5VSB lead, and a corresponding setting in the
BIOS.
KBPWR1
+5V
®
P5S800-VM
1 2
2 3
+5VSB
(Default)
P5S800-VM Keyboard power setting
1.10
Connectors
1.10.1 Rear panel connectors
1
2
3
4
5
6
11
10
9
8
7
1.
2.
P S / 2 m o u s e p o r t ( g r e e n ) . This port is for a PS/2 mouse.
P a r a l l e l p o r t . This 25-pin port connects a parallel printer, a scanner,
or other devices.
3.
L A N ( R J - 4 5 ) p o r t . This port allows Gigabit connection to a Local
Area Network (LAN) through a network hub. Refer to the table below
for the LAN port LED indications.
1-22
Chapter 1: Product introduction
LAN port LED indications
ACT/LINK LED
4.
5.
6.
SPEED LED
Status
Description
Status
Description
OFF
No link
OFF
10 Mbps connection
GREEN
Linked
ORANGE
100 Mbps connection
BLINKING
Data activity
L i n e I n p o r t ( l i g h t b l u e ) . This port connects a tape, CD, DVD
player, or other audio sources. In 4-channel and 6-channel
configuration, the function of this port becomes Front Speaker Out.
L i n e O u t p o r t ( l i m e ) . This port connects a headphone or a
speaker. In 4-channel and 6-channel configuration, the function of this
port becomes Rear Speaker Out.
M i c r o p h o n e p o r t ( p i n k ) . This port connects a microphone. In a
6-channel configuration, the function of this port becomes Center/
Subwoofer.
Refer to the audio configuration table for the function of the audio ports
in 2, 4, or 6-channel configuration.
Audio 2, 4, or 6-channel configuration
Port
Headset
2-channel
4-channel
Line In
Front Speaker Out
Front Speaker Out
Lime
Line Out
Rear Speaker Out
Rear Speaker Out
Pink
Mic In
Mic In
Center/Subwoofer
Light Blue
7.
8.
6-channel
U S B 2 . 0 p o r t s 3 a n d 4 . These two 4-pin Universal Serial Bus
(USB) ports are available for connecting USB 2.0 devices.
U S B 2 . 0 p o r t s 1 a n d 2 . These two 4-pin Universal Serial Bus
(USB) ports are available for connecting USB 2.0 devices.
V G A p o r t . This 15-pin VGA port connects to a VGA monitor.
9.
1 0 . S e r i a l c o n n e c t o r . This 9-pin COM1 port is for serial devices.
1 1 . P S / 2 k e y b o a r d p o r t ( p u r p l e ) . This port is for a PS/2 keyboard.
ASUS P5S800-VM
1-23
1.10.2 Internal connectors
1.
Floppy disk drive connector (34-1 pin FLOPPY1)
This connector is for the provided floppy disk drive (FDD) signal cable.
Insert one end of the cable to this connector, then connect the other
end to the signal connector at the back of the floppy disk drive.
Pin 5 on the connector is removed to prevent incorrect cable connection
when using an FDD cable with a covered Pin 5.
FLOPPY1
®
P5S800-VM
NOTE: Orient the red markings on
the floppy ribbon cable to PIN 1.
PIN 1
P5S800-VM Floppy disk drive connector
Primary IDE connector (40-1 pin PRI_IDE1, SEC_IDE1)
These connectors are for Ultra DMA 100/66 signal cables. The Ultra
DMA 100/66 signal cable has three connectors: a blue connector for
the primary IDE connector on the motherboard, a black connector for
an Ultra DMA 100/66 IDE slave device (optical drive/hard disk drive),
and a gray connector for an Ultra DMA 100/66 IDE master device (hard
disk drive). If you install two hard disk drives, you must configure the
second drive as a slave device by setting its jumper accordingly. Refer
to the hard disk documentation for the jumper settings.
•
Pin 20 on the IDE connector is removed to match the covered hole
on the Ultra DMA cable connector. This prevents incorrect insertion
when you connect the IDE cable.
•
Use the 80-conductor IDE cable for Ultra DMA 100/66 IDE devices.
NOTE: Orient the red markings
(usually zigzag) on the IDE
ribbon cable to PIN 1.
P5S800-VM IDE connectors
1-24
PRI_IDE1
SEC_IDE1
®
P5S800-VM
2.
PIN 1
Chapter 1: Product introduction
3.
Serial ATA connectors (7-pin SATA1, SATA2)
These connectors are for the Serial ATA signal cables for Serial ATA
hard disk drives.
®
SATA2
GND
RSATA_RXN1
RSATA_RXP1
GND
RSATA_TXN1
RSATA_TXP1
GND
P5S800-VM
GND
RSATA_RXN2
RSATA_RXP2
GND
RSATA_TXN2
RSATA_TXP2
GND
If you installed Serial ATA hard disk drives, you can can create a RAID
0 or RAID 1 configuration through the onboard SIS 964 RAID
controller.
P5S800-VM SATA connectors
SATA1
Important notes on Serial ATA
4.
•
The Serial ATA RAID feature (RAID 0, RAID 1) is available only if you
are using Windows® 2000/XP.
•
Install the Windows® 2000 Service Pack 4 or the Windows® XP
Service Pack1 or later before using Serial ATA.
Speaker connector (4-pin SPEAKER1)
®
P5S800-VM
This 4-pin connector is for the chassis-mounted system warning
speaker. The speaker allows you to hear system beeps and warnings.
SPEAKER1
Speak Out
GND
GND
+5V
1
P5S800-VM Speaker out connector
ASUS P5S800-VM
1-25
5.
CPU and Chassis fan connectors
(4-pin CPU_FAN1, 3-pin CHA_FAN1)
The fan connectors support cooling fans of 350mA~740mA (8.88W
max.) or a total of 1A~2.22A (26.64W max.) at +12V. Connect the fan
cables to the fan connectors on the motherboard, making sure that the
black wire of each cable matches the ground pin of the connector.
Do not forget to connect the fan cables to the fan connectors.
Insufficient air flow inside the system may damage the motherboard
components. These are not jumpers! DO NOT place jumper caps on the
fan connectors.
CPU_FAN1
®
P5S800-VM
CPU FAN PWM
CPU FAN IN
CPU FAN PWR
GND
GND
+12V
Rotation
CHA_FAN1
P5S800-VM Fan connectors
6.
Digital Audio connector (4-1 pin SPDIF1)
SPDIFOUT
GND
+5V
®
P5S800-VM
This connector is for the S/PDIF audio module to allow digital sound
output. Connect one end of the S/PDIF audio cable to this connector
and the other end to the S/PDIF module.
SPDIF1
P5S800-VM Digital audio connector
The S/PDIF out module is purchased separately.
1-26
Chapter 1: Product introduction
7.
ATX power connectors (20-pin ATXPWR1, 4-pin ATX12V1)
These connectors are for an ATX power supply. The plugs from the
power supply are designed to fit these connectors in only one
orientation. Find the proper orientation and push down firmly until the
connectors completely fit.
•
You can also use a Power Supply Unit (PSU) with a 24-pin ATX power
connector on this motherboard.
•
Do not forget to connect the 4-pin ATX +12 V power plug;
otherwise, the system will not boot up.
•
Use a PSU with a minimum power rating of 300 W on this
motherboard. Use of a PSU with a higher power output is
recommended when configuring a system with more
power-consuming devices. The system may become unstable or may
not boot up if the power is inadequate.
ATX12V1
+12V DC GND
®
P5S800-VM
+12V DC GND
ATXPWR1
P5S800-VM ATX power connectors
8.
+12.0VDC
+5VSB
PWR_OK
COM
+5.0VDC
COM
+5.0VDC
COM
+3.3VDC
+3.3VDC
+5.0VDC
+5.0VDC
-5.0VDC
COM
COM
COM
PS_ON#
COM
-12.0VDC
+3.3VDC
Power LED connector (3-1 pin PLED1)
®
P5S800-VM
This 3-1 pin connector is for the system power LED. The system
power LED lights up when you turn on the system power, and blinks
when the system is in sleep mode.
PLED1
PLEDNC
PLED+
1
P5S800-VM PLED connector
ASUS P5S800-VM
1-27
Ground
Right Audio Channel
Left Audio Channel
Right Audio Channel
Ground
®
Left Audio Channel
Internal audio connectors (4-pin CD1, AUX1)
These connectors allow you to receive stereo audio input from sound
sources such as a CD-ROM, TV tuner, MPEG card or modem.
P5S800-VM
9.
AUX1 (White) CD1 (Black)
P5S800-VM Internal audio connectors
1 0 . USB connectors (10-1 pin USB56, USB78)
P5S800-VM USB 2.0 connectors
1
USB+5V
USB_P7USB_P7+
GND
USB78
1
USB+5V
USB_P5USB_P5+
GND
USB56
USB+5V
USB_P8USB_P8+
GND
NC
USB+5V
USB_P6USB_P6+
GND
NC
®
P5S800-VM
These connectors are for USB 2.0 ports. Connect the optional
USB/GAME module cable to any of these connectors, then install the
module to a slot opening at the back of the system chassis. These
USB connectors comply with USB 2.0 specification that supports up to
480 Mbps connection speed.
Never connect a 1 3 9 4 c a b l e to the USB connectors. Doing so will
damage the motherboard!
The USB/GAME module is purchased separately.
1-28
Chapter 1: Product introduction
BLINE_OUT_L
AGND
+5VA
BLINE_OUT_R
®
P5S800-VM
1 1 . Front panel audio connector (10-1 pin FP_AUDIO1)
This connector is for a chassis-mounted front panel audio I/O module
that supports legacy AC ‘97 audio standard. Connect one end of the
front panel audio I/O module cable to this connector.
MIC2
MICPWR
Line out_R
NC
Line out_L
FP_AUDIO1
P5S800-VM Front panel audio connector
1 2 . Serial port connector (10-1 pin COM2)
This connector is for a serial (COM) port. Connect the serial port
module cable to this connector, then install the module to a slot
opening at the back of the system chassis.
®
P5S800-VM
COM2
PIN 1
P5S800-VM Serial port connector
The Serial port module is purchased separately.
ASUS P5S800-VM
1-29
1 3 . Chassis intrusion connector (4-1 pin CHASSIS1)
This connector is for a chassis-mounted intrusion detection sensor or
switch. Connect one end of the chassis intrusion sensor or switch
cable to this connector. The chassis intrusion sensor or switch sends a
high-level signal to this connector when a chassis component is
removed or replaced. The signal is then generated as a chassis
intrusion event.
By default, the pins labeled “Chassis Signal” and “Ground” are shorted
with a jumper cap. Remove the jumper caps only when you intend to
use the chassis intrusion detection feature.
Chassis Signal
GND
+5VSB_MB
®
P5S800-VM
CHASSIS1
(Default)
P5S800-VM Chassis intrusion connector
1-30
Chapter 1: Product introduction
1 4 . System panel connector (10-1 pin F_PANEL1)
This connector supports several chassis-mounted functions.
PLED+
PLEDPWR
GND
®
P5S800-VM
PLED PWRBTN*
HDLED+
HDLEDGround
Reset
F_PANEL1
HDLED RESET
P5S800-VM System panel connector
The sytem panel connector is color-coded for easy connection. Refer to
the connector description below for details.
•
•
•
•
System power LED (Green 2-pin PLED)
This 2-pin connector is for the system power LED. Connect the
chassis power LED cable to this connector. The system power LED
lights up when you turn on the system power, and blinks when the
system is in sleep mode.
Hard disk drive activity (Red 2-pin HDLED)
This 2-pin connector is for the HDD Activity LED. Connect the HDD
Activity LED cable to this connector. The IDE LED lights up or flashes
when data is read from or written to the HDD.
Power/Soft-off button (Black 2-pin PWRBTN)
This connector is for the system power button. Pressing the power
button turns the system ON or puts the system in SLEEP or SOFT-OFF
mode depending on the BIOS settings. Pressing the power switch for
more than four seconds while the system is ON turns the system OFF.
Reset button (Blue 2-pin RESET)
This 2-pin connector is for the chassis-mounted reset button for
system reboot without turning off the system power.
ASUS P5S800-VM
1-31
1-32
Chapter 1: Product introduction
This chapter tells how to change
the system settings through the BIOS
Setup menus. Detailed descriptions
of the BIOS parameters are also
provided.
2
BIOS setup
ASUS P5S800-VM
2-1
2.1
Managing and updating your BIOS
The following utilities allow you to manage and update the motherboard
Basic Input/Output System (BIOS) setup.
1.
2.
ASUS
floppy
ASUS
A F U D O S (Updates the BIOS in DOS mode using a bootable
disk.)
E Z F l a s h (Updates the BIOS using a floppy disk during POST.)
3.
A S U S C r a s h F r e e B I O S 2 (Updates the BIOS using a bootable
floppy disk or the motherboard support CD when the BIOS file fails or
gets corrupted.)
4.
A S U S U p d a t e (Updates the BIOS in Windows® environment.)
Refer to the corresponding sections for details on these utilities.
Save a copy of the original motherboard BIOS file to a bootable floppy
disk in case you need to restore the BIOS in the future. Copy the original
motherboard BIOS using the ASUS Update or AFUDOS utilities.
2.1.1
1.
Creating a bootable floppy disk
Do either one of the following to create a bootable floppy disk.
DOS environment
a. Insert a 1.44MB floppy disk into the drive.
b. At the DOS prompt, type format A:/S then press <Enter>.
Windows® XP environment
a. Insert a 1.44 MB floppy disk to the floppy disk drive.
b. Click S t a r t from the Windows® desktop, then select M y
C o m p u t e rr.
c. Select the 3 1/2 Floppy Drive icon.
d. Click F i l e from the menu, then select F o r m a tt. A F o r m a t 3 1 / 2
F l o p p y D i s k window appears.
e. Select C r e a t e a n M S - D O S s t a r t u p d i s k from the format
options field, then click S t a r tt.
Windows® 2000 environment
To create a set of boot disks for Windows® 2000:
a. Insert a formatted, high density 1.44 MB floppy disk into the drive.
b. Insert the Windows® 2000 CD to the optical drive.
c. Click S t a r tt, then select R u n
n.
2-2
Chapter 2: BIOS setup
d. From the Open field, type
D:\bootdisk\makeboot a:
assuming that D: is your optical drive.
e. Press <Enter>, then follow screen instructions to continue.
2.
Copy the original or the latest motherboard BIOS file to the bootable
floppy disk.
2.1.2
ASUS EZ Flash utility
The ASUS EZ Flash feature allows you to update the BIOS without having to
go through the long process of booting from a floppy disk and using a
DOS-based utility. The EZ Flash utility is built-in the BIOS chip so it is
accessible by pressing <Alt> + <F2> during the Power-On Self Tests
(POST).
To update the BIOS using EZ Flash:
1.
Visit the ASUS website (www.asus.com) to download the latest BIOS
file for the motherboard and rename the same to P 5 S 8 0 0 V M . R O M
M.
2.
Save the BIOS file to a floppy disk, then restart the system.
3.
Press <Alt> + <F2> during POST to display the following.
EZFlash starting BIOS update
Checking for floppy...
4.
Insert the floppy disk that contains the BIOS file to the floppy disk
drive. When the correct BIOS file is found, EZ Flash performs the BIOS
update process and automatically reboots the system when done.
EZFlash starting BIOS update
Checking for floppy...
Floppy found!
Reading file “P5S800VM.ROM”. Completed.
Start erasing.......|
Start programming...|
Flashed successfully. Rebooting.
•
Do not shutdown or reset the system while updating the BIOS to
prevent system boot failure!
•
A “Floppy not found!” error message appears if there is no floppy
disk in the drive. A “P5S800VM.ROM not found!” error message
appears if the correct BIOS file is not found in the floppy disk. Make
sure that you rename the BIOS file to P5S800VM.ROM.
ASUS P5S800-VM
2-3
2.1.3
AFUDOS utility
The AFUDOS utility allows you to update the BIOS file in DOS environment
using a bootable floppy disk with the updated BIOS file. This utility also
allows you to copy the current BIOS file that you can use as backup when
the BIOS fails or gets corrupted during the updating process.
Copying the current BIOS
To copy the current BIOS file using the AFUDOS utility:
•
Make sure that the floppy disk is not write-protected and has at
least 600 KB free space to save the file.
•
The succeeding BIOS screens are for reference only. The actual BIOS
screen displays may not be exactly the same as shown.
1.
Copy the AFUDOS utility (afudos.exe) from the motherboard support
CD to the bootable floppy disk you created earlier.
2.
Boot the system in DOS mode, then at the prompt type:
afudos /o[filename]
where the [filename] is any user-assigned filename not more than
eight alphanumeric characters for the main filename and three
alphanumeric characters for the extension name.
A:\>afudos /oOLDBIOS1.ROM
Main filename
3.
Extension name
Press <Enter>. The utility copies the current BIOS file to the floppy
disk.
A:\>afudos /oOLDBIOS1.ROM
AMI Firmware Update Utility - Version 1.10
Copyright (C) 2002 American Megatrends, Inc. All rights reserved.
Reading flash ..... done
A:\>
The utility returns to the DOS prompt after copying the current BIOS
file.
2-4
Chapter 2: BIOS setup
Updating the BIOS file
To update the BIOS file using the AFUDOS utility:
1.
Visit the ASUS website (www.asus.com) and download the latest BIOS
file for the motherboard. Save the BIOS file to a bootable floppy disk.
Write the BIOS filename on a piece of paper. You need to type the exact
BIOS filename at the DOS prompt.
2.
Copy the AFUDOS utility (afudos.exe) from the motherboard support
CD to the bootable floppy disk you created earlier.
3.
Boot the system in DOS mode, then at the prompt type:
afudos /i[filename]
where [filename] is the latest or the original BIOS file on the bootable
floppy disk.
A:\>afudos /iP5S800VM.ROM
4.
The utility verifies the file and starts updating the BIOS.
A:\>afudos /iP5S800VM.ROM
AMI Firmware Update Utility - Version 1.10
Copyright (C) 2002 American Megatrends, Inc. All rights reserved.
Reading file ..... done
Erasing flash .... done
Writing flash .... 0x0008CC00 (9%)
Do not shut down or reset the system while updating the BIOS to
prevent system boot failure!
5.
The utility returns to the DOS prompt after the BIOS update process is
completed. Reboot the system from the hard disk drive.
A:\>afudos /iP5S800VM.ROM
AMI Firmware Update Utility - Version 1.10
Copyright (C) 2002 American Megatrends, Inc. All rights reserved.
Reading file ..... done
Erasing flash .... done
Writing flash .... 0x0008CC00 (9%)
Verifying flash .. done
A:\>
ASUS P5S800-VM
2-5
2.1.4
ASUS CrashFree BIOS 2 utility
The ASUS CrashFree BIOS 2 is an auto recovery tool that allows you to
restore the BIOS file when it fails or gets corrupted during the updating
process. You can update a corrupted BIOS file using the motherboard
support CD or the floppy disk that contains the updated BIOS file.
•
Prepare the motherboard support CD or the floppy disk containing
the updated motherboard BIOS before using this utility.
•
Make sure that you rename the original or updated BIOS file in the
floppy disk to P 5 S 8 0 0 V M . R O M
M.
Recovering the BIOS from a floppy disk
To recover the BIOS from a floppy disk:
1.
Turn on the system.
2.
Insert the floppy disk with the original or updated BIOS file to the
floppy disk drive.
3.
The utility displays the following message and automatically checks
the floppy disk for the original or updated BIOS file.
Bad BIOS checksum. Starting BIOS recovery...
Checking for floppy...
When found, the utility reads the BIOS file and starts flashing the
corrupted BIOS file.
Bad BIOS checksum. Starting BIOS recovery...
Checking for floppy...
Floppy found!
Reading file “P5S800VM.ROM”. Completed.
Start flashing...
DO NOT shut down or reset the system while updating the BIOS! Doing
so can cause system boot failure!
4.
2-6
Restart the system after the utility completes the updating process.
Chapter 2: BIOS setup
Recovering the BIOS from the support CD
To recover the BIOS from the support CD:
1.
Remove any floppy disk from the floppy disk drive, then turn on the
system.
2.
Insert the support CD to the optical drive.
3.
The utility displays the following message and automatically checks
the floppy disk for the original or updated BIOS file.
Bad BIOS checksum. Starting BIOS recovery...
Checking for floppy...
When no floppy disk is found, the utility automatically checks the
optical drive for the original or updated BIOS file. The utility then
updates the corrupted BIOS file.
Bad BIOS checksum. Starting BIOS recovery...
Checking for floppy...
Floppy not found!
Checking for CD-ROM...
CD-ROM found!
Reading file “P5S800VM.ROM”. Completed.
Start flashing...
DO NOT shut down or reset the system while updating the BIOS! Doing
so can cause system boot failure!
4.
Restart the system after the utility completes the updating process.
The recovered BIOS may not be the latest BIOS version for this
motherboard. Visit the ASUS website (www.asus.com) to download the
latest BIOS file.
ASUS P5S800-VM
2-7
2.1.5
ASUS Update utility
The ASUS Update is a utility that allows you to manage, save, and update
the motherboard BIOS in Windows® environment. The ASUS Update utility
allows you to:
• Save the current BIOS file
• Download the latest BIOS file from the Internet
• Update the BIOS from an updated BIOS file
• Update the BIOS directly from the Internet, and
• View the BIOS version information.
This utility is available in the support CD that comes with the motherboard
package.
ASUS Update requires an Internet connection either through a network
or an Internet Service Provider (ISP).
Installing ASUS Update
To install ASUS Update:
2.
Place the support CD in the optical drive. The D r i v e r s menu appears.
Click the U t i l i t i e s tab, then click I n s t a l l A S U S U p d a t e
VX.XX.XX
X. See page 3-4 for the U t i l i t i e s screen menu.
3.
The ASUS Update utility is copied to your system.
1.
Quit all Windows® applications before you update the BIOS using this
utility.
2-8
Chapter 2: BIOS setup
Updating the BIOS through the Internet
To update the BIOS through the Internet:
1.
Launch the ASUS Update utility from the Windows® desktop by clicking
Start > Programs > ASUS > ASUSUpdate > ASUSUpdate
e. The
ASUS Update main window appears.
2.
Select U p d a t e B I O S f r o m
t h e I n t e r n e t option from the
drop-down menu, then click
N e x tt.
ASUS P5S800-VM
3.
Select the ASUS FTP site
nearest you to avoid network
traffic, or click A u t o S e l e c tt.
Click N e x tt.
2-9
4.
From the FTP site, select the
BIOS version that you wish to
download. Click Next.
5.
Follow the screen instructions to
complete the update process.
The ASUS Update utility is
capable of updating itself
through the Internet. Always
update the utility to avail all
its features.
Updating the BIOS through a BIOS file
To update the BIOS through a BIOS file:
1.
2.
Launch the ASUS Update utility from the Windows® desktop by
clicking S t a r t > P r o g r a m s > A S U S > A S U S U p d a t e >
ASUSUpdate
e. The ASUS Update main window appears.
Select U p d a t e B I O S f r o m a
f i l e option from the drop-down
menu, then click N e x tt.
3.
Locate the BIOS file from the
O p e n window, then click S a v e
e.
4.
Follow the screen instructions to
complete the update process.
2-10
Chapter 2: BIOS setup
2.2
BIOS setup program
This motherboard supports a programmable firmware chip that you can
update using the provided utility described in section “2.1 Managing and
updating your BIOS.”
Use the BIOS Setup program when you are installing a motherboard,
reconfiguring your system, or prompted to “Run Setup.” This section
explains how to configure your system using this utility.
Even if you are not prompted to use the Setup program, you can change
the configuration of your computer in the future. For example, you can
enable the security password feature or change the power management
settings. This requires you to reconfigure your system using the BIOS
Setup program so that the computer can recognize these changes and
record them in the CMOS RAM of the firmware hub.
The firmware hub on the motherboard stores the Setup utility. When you
start up the computer, the system provides you with the opportunity to
run this program. Press <Del> during the Power-On Self-Test (POST) to
enter the Setup utility; otherwise, POST continues with its test routines.
If you wish to enter Setup after POST, restart the system by pressing
<Ctrl+Alt+Delete>, or by pressing the reset button on the system chassis.
You can also restart by turning the system off and then back on. Do this
last option only if the first two failed.
The Setup program is designed to make it as easy to use as possible. Being
a menu-driven program, it lets you scroll through the various sub-menus
and make your selections from the available options using the navigation
keys.
•
The default BIOS settings for this motherboard apply for most
conditions to ensure optimum performance. If the system becomes
unstable after changing any BIOS settings, load the default settings
to ensure system compatibility and stability. Select the L o a d
D e f a u l t S e t t i n g s item under the Exit Menu. See section “2.7 Exit
Menu.”
•
The BIOS setup screens shown in this section are for reference
purposes only, and may not exactly match what you see on your
screen.
•
Visit the ASUS website (www.asus.com) to download the latest BIOS
file for this motherboard and .
ASUS P5S800-VM
2-11
2.2.1
BIOS menu screen
Menu items
Menu bar
System Time
System Date
Legacy Diskette A
Primary IDE Master
Primary IDE Slave
Secondary IDE Master
Secondary IDE Slave
OnChip SATA Controller
Configuration fields
[11:51:19]
[Thu 12/29/2005]
[1.44M, 3.5 in]
: [ST320413A]
: [ASUS CD-S360]
: [Not Detected]
: [Not Detected]
[RAID Mode]
General help
Use [ENTER], [TAB]
or [SHIFT-TAB] to
select a field.
Use [+] or [-] to
configure system time.
System Information
Sub-menu items
2.2.2
Navigation keys
Menu bar
The menu bar on top of the screen has the following main items:
Main
Advanced
For changing the basic system configuration
Power
For changing the advanced power management (APM)
configuration
Boot
Exit
For changing the system boot configuration
For changing the advanced system settings
For selecting the exit options and loading default
settings
To select an item on the menu bar, press the right or left arrow key on the
keyboard until the desired item is highlighted.
2.2.3
Navigation keys
At the bottom right corner of a menu screen are the navigation keys for
that particular menu. Use the navigation keys to select items in the menu
and change the settings.
Some of the navigation keys differ from one screen to another.
2-12
Chapter 2: BIOS setup
2.2.4
Menu items
The highlighted item on the menu bar
displays the specific items for that menu.
For example, selecting M a i n shows the
Main menu items.
The other items (Advanced, Power, Boot,
and Exit) on the menu bar have their
respective menu items.
2.2.5
Main menu items
Sub-menu items
A solid triangle before each item on any menu screen means that the iteam
has a sub-menu. To display the sub-menu, select the item and press
<Enter>.
2.2.6
Configuration fields
These fields show the values for the menu items. If an item is userconfigurable, you can change the value of the field opposite the item. You
cannot select an item that is not user-configurable.
A configurable field is enclosed in brackets, and is highlighted when
selected. To change the value of a field, select it then press <Enter> to
display a list of options. Refer to “2.2.7 Pop-up window.”
2.2.7
Pop-up window
Select a menu item then press <Enter> to display a pop-up window with
the configuration options for that item.
2.2.8
Scroll bar
A scroll bar appears on the right side
of a menu screen when there are
items that do not fit on the screen.
Press the
Up/Down arrow keys or <Page Up> /
<Page Down> keys to display the
other items on the screen.
2.2.9
General help
Pop-up window
Scroll bar
At the top right corner of the menu
screen is a brief description of the
selected item.
ASUS P5S800-VM
2-13
2.3
Main menu
When you enter the BIOS Setup program, the Main menu screen appears,
giving you an overview of the basic system information.
Refer to section “2.2.1 BIOS menu screen” for information on the menu
screen items and how to navigate through them.
System Time
System Date
Legacy Diskette A
Primary IDE Master
Primary IDE Slave
Secondary IDE Master
Secondary IDE Slave
OnChip SATA Controller
Use [ENTER], [TAB], or
[SHIFT-TAB] to select
a field.
[11:51:19]
[Thu 12/29/2005]
[1.44M, 3.5 in]
Use [+] or [-] to
configure system time.
: [ST320413A]
: [ASUS CD-S360]
: [Not Detected]
: [Not Detected]
[Raid Mode]
System Information
2.3.1
System Time [xx:xx:xx]
Allows you to set the system time.
2.3.2
System Date [Day xx/xx/xxxx]
Allows you to set the system date.
2.3.3
Legacy Diskette A [1.44M, 3.5 in.]
Sets the type of floppy drive installed. Configuration options: [Disabled]
[360K, 5.25 in.] [1.2M , 5.25 in.] [720K , 3.5 in.] [1.44M, 3.5 in.]
[2.88M, 3.5 in.]
2-14
Chapter 2: BIOS setup
2.3.4
Primary and Secondary IDE Master/Slave
While entering Setup, the BIOS automatically detects the presence of IDE
devices. There is a separate sub-menu for each IDE device. Select a device
item then press <Enter> to display the IDE device information.
Primary IDE Master
Device
: Hard Disk
Vendor
: ST320413A
Size
: 20.0GB
LBA Mode
: Supported
Block Mode
: 16 Sectors
PIO Mode
: 4
Async DMA
: MultiWord DMA-2
Ultra DMA
: Ultra DMA-5
SMART Monitoring: Supported
Type
LBA/Large Mode
Block(Multi-sector Transfer)
PIO Mode
SMART Monitoring
32Bit Data Transfer
Select the type of
device connected to
the system.
[Auto]
[Auto]
[Auto]
[Auto]
[Auto]
[Disabled]
The BIOS automatically detects the values opposite the dimmed items
(Device, Vendor, Size, LBA Mode, Block Mode, PIO Mode, Async DMA, Ultra
DMA, and SMART monitoring). These values are not user-configurable.
These items show N/A if no IDE device is installed in the system.
Type [Auto]
Selects the type of IDE drive. Setting to Auto allows automatic selection of
the appropriate IDE device type. Select CDROM if you are specifically
configuring a CD-ROM drive. Select ARMD (ATAPI Removable Media Device)
if your device is either a ZIP, LS-120, or MO drive.
Configuration options: [Not Installed] [Auto] [CDROM] [ARMD]
LBA/Large Mode [Auto]
Enables or disables the LBA mode. Setting to Auto enables the LBA mode if
the device supports this mode, and if the device was not previously
formatted with LBA mode disabled. Configuration options: [Disabled]
[Auto]
Block (Multi-sector Transfer) [Auto]
Enables or disables data multi-sectors transfers. When set to Auto, the
data transfer from and to the device occurs multiple sectors at a time if
the device supports multi-sector transfer feature. When set to [Disabled],
the data transfer from and to the device occurs one sector at a time.
Configuration options: [Disabled] [Auto]
ASUS P5S800-VM
2-15
PIO Mode [Auto]
Selects the PIO mode.
Configuration options: [Auto] [0] [1] [2] [3] [4]
SMART Monitoring [Auto]
Sets the Smart Monitoring, Analysis, and Reporting Technology.
Configuration options: [Auto] [Disabled] [Enabled]
32Bit Data Transfer [Disabled]
Enables or disables 32-bit data transfer.
Configuration options: [Disabled] [Enabled]
2.3.5
OnChip SATA Controller [Raid Mode]
Enables or disables the onchip Serial ATA controller.
Configuration options: [Disabled] [Native Mode] [Raid Mode]
2.3.6
System Information
This menu gives you an overview of the general system specifications. The
BIOS automatically detects the items in this menu.
AMIBIOS
Version
: 08.00.09
Build Date : 12/19/05
Processor
Type
Speed
Count
: Genuine Intel(R) CPU 3.20GHz
: 2800 MHz
: 1
System Memory
Size
: 512MB
AMI BIOS
Displays the auto-detected BIOS information.
Processor
Displays the auto-detected CPU specification.
System Memory
Displays the auto-detected system memory.
2-16
Chapter 2: BIOS setup
2.4
Advanced menu
The Advanced menu items allow you to change the settings for the CPU
and other system devices.
Take caution when changing the settings of the Advanced menu items.
Incorrect field values may cause the system to malfunction.
Adjust system
frequency/voltage
JumperFree Configuration
CPU Configuration
Chipset
Onboard Devices Configuration
PCIPnP
USB Configuration
Instant Music Configuration
2.4.1
JumperFree Configuration
Configure System Frequency/Voltage
AI Overclock Tuner
Spread Spectrum
DRAM Frequency
[Standard]
[Enabled]
[Auto]
Select the target CPU
frequency, and the
relevant parameters
will be auto-adjusted.
Frequencies higher than
CPU manufacturer
recommends are not
guaranteed to be
stable. If the system
becomes unstable,
return to the default.
AI Overclock Tuner [Auto]
Allows you to select the overclocking options to achieve the desired CPU
internal frequency. [Standard] loads the standard settings for the system.
Configuration options: [Standard] [Overclock 5%] [Overclock 10%]
[Overclock 20%] [Overclock 30%]
ASUS P5S800-VM
2-17
The A G P / P C I F r e q u e n c y item appears when you set the AI Overclock
Tuner to [Overclock 5%, 10%, 20%, or 30%].
AGP/PCI Frequency [Auto]
Allows you to set the AGP/PCI frequency.
Configuration options: [Auto] [66.6/33.3] [75.0/37.5] [85.7/42.8]
Spread Spectrum [Enabled]
Allows you to enable or disable the clock generator spread spectrum.
Configuration options: [Disabled] [Enabled]
DRAM Frequency [Auto]
Sets the DDR operating frequency.
Configuration options: [Auto] [200 Mhz] [266 Mhz] [333 Mhz] [400 Mhz]
2.4.2
CPU Configuration
The items in this menu show the CPU-related information auto-detected by
BIOS.
Configure Advanced CPU settings
Manufacturer:
Brand String:
Frequency
:
FSB Speed
:
Cache L1
Cache L2
Cache L3
Intel
Intel(R) Pentium(R) 4 CPU 2.80GHz
2806Mhz
800Mhz
: 16 KB
: 1024 KB
: 0 KB
Sets the ratio between
CPU Core Clock and the
FSB Frequency.
NOTE: If an invalid
ratio is set in CMOS
then actual and
setpoint values may
differ.
Ratio Status: Unlocked (Max:22, Min:14)
Ratio Actual Value: 14
Ratio CMOS Setting:
[ 22]
Max CPUID Value Limit:
[Disabled]
Execute Disable Function
[Disabled]
Hardware Prefetcher:
[Enabled]
Adjacent Cache Line Prefetcher
[Enabled]
CPU Internal Thermal Control
[Auto]
Hyper Threading Function
[Enabled]
Ratio CMOS Setting [ 22]
Sets the ratio between the CPU core clock and the FSB frequency.
Max CPUID Value Limit [Disabled]
This item allows you to enable or disable the maximum CPUID value limit.
Configuration options: [Disabled] [Enabled]
2-18
Chapter 2: BIOS Setup
Execute Disable Function [Disabled]
This item allows you to enable or disable the No-Execution Page Protection
technology, which can force the XD feature flag to always return to 0.
Configuration options: [Disabled] [Enabled]
Hardware Prefetcher [Enabled]
This item allows you to enable or disable the hardware prefetcher feature.
Configuration options: [Disabled] [Enabled]
Adjacent Cache Line Prefetch [Enabled]
This item allows you to enable or disable the adjacent cache line prefetch
feature. Configuration options: [Disabled] [Enabled]
CPU Internal Thermal Control [Auto]
This item allows you to disable or set to auto the Intel® Thermal Monitoring
2 feature. Configuration options: [Auto] [Disabled]
Hyper-Threading Function [Enabled]
This item allows you to enable or disable the processor Hyper-Threading
Technology. Configuration options: [Disabled] [Enabled]
ASUS P5S800-VM
2-19
2.4.3
Chipset
The Chipset menu items allow you to change the advanced chipset
settings. Select an item then press <Enter> to display the sub-menu.
NorthBridge SiS661FX Configuration
SouthBridge SiS964 Configuration
NorthBridge SiS661FX Configuration
Primary Graphics Adapter
MA 1T/2T Select
DRAM CAS# Latency
DRAM Precharge Delay
DRAM RAS# to CAS# Delay
DRAM RAS# Precharge
Graphic Win Size
AGP Fast Write Control
[PCI]
[Auto]
[By SPD]
[Auto]
[Auto]
[Auto]
[ 64MB]
[Disabled]
Share Memory Size
[ 32MB]
<Enter> to select.
Primary Graphics Adapter [PCI]
Allows selection of the graphics controller to use as primary boot device.
Configuration options: [PCI] [AGP] [Onboard AGP]
MA 1T/2T Select [Auto]
Configuration options: [Auto] [MA 2T] [1T]
DRAM CAS# Latency [By SPD]
This item controls the latency between the SDRAM read command and the
time the data actually becomes available.
Configuration options: [By SPD] [2T] [2.5T] [3T]
DRAM Precharge Delay [Auto]
Configuration options: [Auto] [6T] [7T] [5T] [4T] [8T] [9T]
DRAM RAS# to CAS# Delay [Auto]
This item controls the latency between the DDR SDRAM active command and
the read/write command. Configuration options: [Auto] [3T] [2T] [4T] [5T]
DRAM RAS# Precharge [Auto]
This item controls the idle clocks after issuing a precharge command to the
DDR SDRAM. Configuration options: [Auto] [3T] [2T] [4T] [5T]
2-20
Chapter 2: BIOS Setup
Graphics Win Size [64MB]
Allows you to select the size of mapped memory for AGP graphic data.
Configuration options: [32MB] [64MB] [128MB]
AGP Fast Write Control [Disabled]
Disables or enables the AGP Fast Write Control function.
Configuration options: [Disabled] [Enabled]
Share Memory Size [ 32MB]
Sets the share memory size. Configuration options: [16MB] [32MB]
[64MB] [128MB] [Disabled]
SouthBridge SiS964 Configuration
Onboard AC97 Audio Device
[Enabled]
Onboard AC97 Audio Device [Enabled]
This item enables or disables the onboard AC’97 audio CODEC device.
Configuration options: [Disabled] [Enabled]
2.4.4
Onboard Devices Configuration
Configure Onboard Device
Serial Port1 Address
Serial Port2 Address
Parallel Port Address
Parallel Port Mode
ECP Mode DMA Channel
Parallel Port IRQ
Onboard Game/MIDI Port
[3F8/IRQ4]
[2F8/IRQ3]
[378]
[ECP]
[DMA3]
[IRQ7]
[Disabled]
Onboard RTL8100C LAN DEVICE
Onboard LAN Boot ROM
[Enabled]
[Disabled]
Allows the BIOS to
select the Serial
Port1 Base Addresses.
Serial Port1 Address [3F8/IRQ4]
Allows you to select the Serial Port1 base address.
Configuration options: [Disabled] [3F8/IRQ4] [3E8/IRQ4] [2E8/IRQ3]
Serial Port2 Address [2F8/IRQ3]
Allows you to select the Serial Port2 base address. Configuration options:
[Disabled] [2F8/IRQ3] [3E8/IRQ4] [2E8/IRQ3]
ASUS P5S800-VM
2-21
Parallel Port Address [378]
Allows you to select the Parallel Port base addresses. Configuration
options: [Disabled] [378] [278] [3BC]
Parallel Port Mode [ECP]
Allows you to select the Parallel Port mode. When the item P a r a l l e l P o r t
A d d r e s s is set to 3 B C
C, the Parallel Port Mode options are only Normal,
Bi-directional, and ECP. Configuration options: [Normal] [Bi-directional]
[EPP] [ECP]
ECP Mode DMA Channel [DMA3]
Allows selection of the Parallel Port ECP DMA channel. This item
appears only when the P a r a l l e l P o r t M o d e is set to E C P
P.
Configuration options: [DMA0] [DMA1] [DMA3]
EPP Version [1.9]
Allows selection of the Parallel Port EPP version. This item appears
only when the P a r a l l e l P o r t M o d e is set to E P P
P.
Configuration options: [1.9] [1.7]
Parallel Port IRQ [IRQ7]
Allows you to select the Parallel Port IRQ.
Configuration options: [IRQ5] [IRQ7]
Onboard Game/MIDI Port [Disabled]
Allows you to set the onboard Game/MIDI port address or disable the port.
Configuration options: [Disabled] [200/300] [200/330] [208/300]
[208/330]
Onboard RTL8100C Lan DEVICE [Enabled]
Enables or disables the onboard RTL8100C LAN device.
Configuration options: [Disabled] [Enabled]
OnBoard LAN Boot ROM [Disabled]
Allows you to enable or disable the onboard LAN Boot ROM.
Configuration options: [Disabled] [Enabled]
2-22
Chapter 2: BIOS Setup
2.4.5
PCI PnP
The PCI PnP menu items allow you to change the advanced settings for
PCI/PnP devices. The menu includes setting IRQ and DMA channel resources
for either PCI/PnP or legacy ISA devices, and setting the memory size block
for legacy ISA devices.
Take caution when changing the settings of the PCI PnP menu items.
Incorrect field values can cause the system to malfunction.
Advanced PCI/PnP Settings
WARNING: Setting wrong values in below sections
may cause system to malfunction.
Plug And Play O/S
PCI Latency Timer
Allocate IRQ to PCI VGA
Palette Snooping
PCI IDE BusMaster
[No]
[64]
[Yes]
[Disabled]
[Enabled]
IRQ3
IRQ4
IRQ5
IRQ7
IRQ9
IRQ10
IRQ11
IRQ14
IRQ15
[Available]
[Available]
[Available]
[Available]
[Available]
[Available]
[Available]
[Available]
[Available]
Plug and Play O/S [No]
When set to [No], BIOS configures all the devices in the system. When set
to [Yes] and if you install a Plug and Play operating system, the operating
system configures the Plug and Play devices not required for boot.
Configuration options: [No] [Yes]
PCI Latency Timer [64]
Allows you to select the value in units of PCI clocks for the PCI device
latency timer register. Configuration options: [32] [64] [96] [128] [160]
[192] [224] [248]
Allocate IRQ to PCI VGA [Yes]
When set to [Yes], BIOS assigns an IRQ to PCI VGA card if the card
requests for an IRQ. When set to [No], BIOS does not assign an IRQ to the
PCI VGA card even if requested. Configuration options: [No] [Yes]
Palette Snooping [Disabled]
When set to [Enabled], the palette snooping feature informs the PCI
devices that an ISA graphics device is installed in the system so that the
latter can function correctly. Configuration options: [Disabled] [Enabled]
ASUS P5S800-VM
2-23
PCI IDE BusMaster [Enabled]
Allows BIOS to use PCI bus mastering when reading/writing to IDE devices.
Configuration options: [Disabled] [Enabled]
IRQ xx assigned to [Available]
When set to [Available], the specific IRQ is free for use of PCI/PnP devices.
When set to [Reserved], the IRQ is reserved for legacy ISA devices.
Configuration options: [Available] [Reserved]
2.4.6
USB Configuration
The items in this menu allows you to change the USB-related features.
Select an item then press Enter to display the configuration options.
Onboard SiS USB1.1 DEVICE
Onboard SiS USB2.0 DEVICE
[Enabled]
[Enabled]
<Enter> to enable or
disable.
USB Configuration
Module
Version - 2.24.0-9.4
USB Devices Enabled: None
Legacy USB Support
USB 2.0 Controller Mode
Stop EHCI HC in OHCI handover
[Auto]
[HiSpeed]
[Enabled]
OnBoard SiS USB 1.1 Device [Enabled]
Allows you to enable or disable the onboard SiS USB 1.1 device.
Configuration options: [Disabled] [Enabled]
OnBoard SiS USB 2.0 Device [Enabled]
Allows you to enable or disable the onboard SiS USB 2.0 device.
Configuration options: [Disabled] [Enabled]
•
•
2-24
The Module Version and USB Devices Enabled items show the
auto-detected values. If no USB device is detected, the item shows
None.
Set to [Disabled] if you are using a Windows® 98SE or Windows® ME
OS.
Chapter 2: BIOS Setup
Legacy USB Support [Auto]
Allows you to enable or disable support for legacy USB devices. Setting to
Auto allows the system to detect the presence of USB devices at startup.
If detected, the USB controller legacy mode is enabled. If no USB device is
detected, the legacy USB support is disabled.
Configuration options: [Disabled] [Enabled] [Auto]
USB 2.0 Controller Mode [HiSpeed]
Allows you to configure the USB 2.0 controller in HiSpeed (480 Mbps) or
Full Speed (12 Mbps). Configuration options: [HiSpeed ] [Full Speed]
Stop EHCI HC in OHCI handover [Enabled]
Allows you to enable or disable the feature to stop the EHCI host controller
during the OHCI OS handover call. This is needed when installing operating
systems that do not support EHCI host controllers.
Configuration options: [Disabled] [Enabled]
2.4.7
Instant Music Configuration
Instant Music Option
Instant Music
[Disabled]
If enabled, power up
by PS/2 keyboard and
mouse function will be
disabled.
Instant Music [Disabled]
Allows you to enable or disable the Instant Music feature in BIOS.
Configuration options: [Disabled] [Enabled]
When Instant Music is enabled, the PS/2 keyboard power up feature is
automatically disabled.
Instant Music CD-ROM Drive [IDE Secondary Master]
Allows you to select the CD-ROM drive that you wish to use for the Instant
Music CD playback. Configuration options: [IDE Primary Master]
[IDE Primary Slave] [IDE Secondary Master] [IDE Secondary Slave]
The above item appears only if you enabled the Instant Music item.
ASUS P5S800-VM
2-25
2.5
Power menu
The Power menu items allow you to change the settings for the Advanced
Configuration and Power Interface (ACPI) and the Advanced Power
Management (APM). Select an item then press <Enter> to display the
configuration options.
Suspend Mode
ACPI 2.0 Support
ACPI APIC Support
[Auto]
[No]
[Enabled]
Select the ACPI state
used for System
Suspend.
APM Configuration
Hardware Monitor
2.5.1
Suspend Mode [Auto]
Allows you to select the Advanced Configuration and Power Interface
(ACPI) state to be used for system suspend.
Configuration options: [S1 (POS) Only] [Auto] [S3 Only]
2.5.2
ACPI 2.0 Support [No]
Allows you to add more tables for Advanced Configuration and Power
Interface (ACPI) 2.0 specifications. Configuration options: [No] [Yes]
2.5.3
ACPI APIC Support [Enabled]
Allows you to enable or disable the Advanced Configuration and Power
Interface (ACPI) support in the Application-Specific Integrated Circuit
(ASIC). When set to Enabled, the ACPI APIC table pointer is included in the
RSDT pointer list. Configuration options: [Disabled] [Enabled]
2-26
Chapter 2: BIOS setup
2.5.5
APM Configuration
Power Button Mode
[On/Off]
Restore on AC Power Loss
Power On By PS2 Keyboard
Power On By PS2 Mouse
Power On by PCI Devices
Power On By External Modems
Power On By RTC Alarm
[Always OFF]
[Disabled]
[Disabled]
[Disabled]
[Disabled]
[Disabled]
Enable/Disable RTC
wake from sleep
states.
Power Button Mode [On/Off]
Allows the system to go into On/Off mode or suspend mode when the
power button is pressed. Configuration options: [On/Off] [Suspend]
Restore on AC Power Loss [Always OFF]
When set to Power Off, the system goes into off state after an AC power
loss. When set to Power On, the system goes on after an AC power loss.
When set to Last State, the system goes into either off or on state,
whatever the system state was before the AC power loss.
Configuration options: [Always OFF] [Always On] [Keep Previous State]
Power On By PS/2 Keyboard [Disabled]
Allows you to disable the PS/2 Power-On by keyboard feature or use
specific keys on the keyboard to turn on the system. This feature requires
an ATX power supply that provides at least 1A on the +5VSB lead.
Configuration options: [Disabled] [Space Bar] [Ctrl-Esc] [Power Key]
Power On By PS/2 Mouse [Disabled]
When set to [Enabled], this parameter allows you to use the PS/2 mouse
to turn on the system. This feature requires an ATX power supply that
provides at least 1A on the +5VSB lead. Configuration options: [Disabled]
[Enabled]
Power On By PCI Devices [Disabled]
When set to [Enabled], this parameter allows you to turn on the system
through a PCI LAN or modem card. This feature requires an ATX power
supply that provides at least 1A on the +5VSB lead.
Configuration options: [Disabled] [Enabled]
ASUS P5S800-VM
2-27
Power On By External Modems [Disabled]
This allows either settings of [Enabled] or [Disabled] for powering up the
computer when the external modem receives a call while the computer is in
Soft-off mode. Configuration options: [Disabled] [Enabled]
The computer cannot receive or transmit data until the computer and
applications are fully running. Thus, connection cannot be made on the
first try. Turning an external modem off and then back on while the
computer is off causes an initialization string that turns the system
power on.
Power On By RTC Alarm [Disabled]
Allows you to enable or disable RTC to generate a wake event. When this
item is set to Enabled, the items RTC Alarm Date, RTC Alarm Hour, RTC
Alarm Minute, and RTC Alarm Second appear with set values. Configuration
options: [Disabled] [Enabled]
2.5.6
Hardware Monitor
Hardware Monitor
CPU Temperature
CPU Temperature
MB Temperature
[51ºC/122.5ºF]
[41ºC/105.5ºF]
CPU Fan Speed
CPU Q-Fan Control
Chassis Fan Speed
[3813 RPM]
[Disabled]
[N/A]
VCORE Voltage
3.3V Voltage
5V Voltage
12V Voltage
[ 1.320V]
[ 3.345V]
[ 5.094V]
[11.880V]
CPU Temperature [xxxºC/xxxºF]
MB Temperature [xxxºC/xxxºF]
The onboard hardware monitor automatically detects and displays the
motherboard and CPU temperatures. Select Ignored if you do not wish to
display the detected temperatures.
CPU Fan Speed [xxxxRPM] or [N/A]
The onboard hardware monitor automatically detects and displays the CPU
fan speed in rotations per minute (RPM). If the fan is not connected to the
motherboard, the field shows N/A. Select Ignored if you do not wish to
display the detected fan speed.
2-28
Chapter 2: BIOS setup
CPU Q-Fan Control [Disabled]
Allows you to enable or disable the CPU Q-Fan Control feature that smarly
adjusts the fan speeds for more efficient system operation. Configuration
options: [Disabled] [Enabled]
The two succeeding iems appear when the C P U Q - F a n C o n t r o l item
is set to [Enabled].
CPU Fan Ratio [Auto]
Allows you to set the appropriate CPU fan speed ratio for the system. The
default [Auto] automatically selecs the fan speed ratio when operating at
low CPU temperature. Select a higher ratio if you installed additional
devices and the system requires more ventilation. Configuration options:
[90%] [80%] [70%] ~ [20%]
CPU Target Temperature [xxx ºC]
Allows you to set the CPU temperature threshold when the CPU fan speed
is increased to lower the CPU temperature. The configuration options for
ths item depend on the recommended Intel® Fan Speed Control (FSC)
temperature settings. The Intel® FSC provides target temperature options
at 50 ~ 90 ºC with 4 ºC intervals.
Chassis Fan Speed [xxxxRPM] or [N/A]
The onboard hardware monitor automatically detects and displays the
chassis fan speed in rotations per minute (RPM). If the fan is not connected
to the chassis, the specific field shows N/A. Select Ignored if you do not
wish to display the detected fan speed.
VCORE Voltage, 3.3V Voltage, 5V Voltage, 12V Voltage
The onboard hardware monitor automatically detects the voltage output
through the onboard voltage regulators.
ASUS P5S800-VM
2-29
2.6
Boot menu
The Boot menu items allow you to change the system boot options. Select
an item then press <Enter> to display the sub-menu.
Specifies the Boot
Device Priority
sequence.
Boot Settings
Boot Device Priority
Boot Settings Configuration
Security
2.6.1
Boot Device Priority
Boot Device Priority
1st Boot Device
2nd Boot Device
3rd Boot Device
[1st FLOPPY DRIVE]
[PM-ST330620A]
[PS-ASUS CD-S360]
Specifies the boot
sequence from the
available devices.
1st ~ xxth Boot Device [1st Floppy Drive]
These items specify the boot device priority sequence from the available
devices. The number of device items that appears on the screen depends
on the number of devices installed in the system.
Configuration options: [xxxxx Drive] [Disabled]
2.6.2
Hard Disk Drives
Hard Disk Drives
1st Drive
2nd Drive
[PM-IBM-DJNA-371350]
[Maxtor 6B200M0]
1st ~ xxth Drive [XXX Drive]
These items displays the available hard disk drives. The number of device
items that appears on the screen depends on the number of devices
installed in the system. This item appears only when you install additional
disk drives on your system. Configuration options: [xxxxx Drive] [Disabled]
2-30
Chapter 2: BIOS setup
2.6.3
Boot Settings Configuration
Boot Settings Configuration
Quick Boot
Full Screen Logo
AddOn ROM Display Mode
Bootup Num-Lock
PS/2 Mouse Support
Wait For ‘F1’ If Error
Hit ‘DEL’ Message Display
Interrupt 19 Capture
[Enabled]
[Enabled]
[Force BIOS]
[On]
[Auto]
[Enabled]
[Enabled]
[Disabled]
Allows BIOS to skip
certain tests while
booting. This will
decrease the time
needed to boot the
system.
Quick Boot [Enabled]
Enabling this item allows the BIOS to skip some power on self tests (POST)
while booting to decrease the time needed to boot the system. When set
to [Disabled], BIOS performs all the POST items.
Configuration options: [Disabled] [Enabled]
Full Screen Logo [Enabled]
This allows you to enable or disable the full screen logo display feature.
Configuration options: [Disabled] [Enabled]
Set this item to [Enabled] to use the ASUS MyLogo2™ feature.
Add On ROM Display Mode [Force BIOS]
Sets the display mode for option ROM.
Configuration options: [Force BIOS] [Keep Current]
Bootup Num-Lock [On]
Allows you to select the power-on state for the NumLock.
Configuration options: [Off] [On]
PS/2 Mouse Support [Auto]
Allows you to enable or disable support for PS/2 mouse.
Configuration options: [Disabled] [Enabled] [Auto]
Wait for ‘F1’ If Error [Enabled]
When set to Enabled, the system waits for the F1 key to be pressed when
error occurs. Configuration options: [Disabled] [Enabled]
Hit ‘DEL’ Message Display [Enabled]
When set to Enabled, the system displays the message “Press DEL to run
Setup” during POST. Configuration options: [Disabled] [Enabled]
ASUS P5S800-VM
2-31
Interrupt 19 Capture [Disabled]
When set to [Enabled], this function allows the option ROMs to trap
Interrupt 19. Configuration options: [Disabled] [Enabled]
2.6.4
Security
The Security menu items allow you to change the system security settings.
Select an item then press <Enter> to display the configuration options.
Security Settings
Supervisor Password
User Password
: Not Installed
: Not Installed
<Enter> to change
password.
<Enter> again to
disabled password.
Change Supervisor Password
Change Supervisor Password
Select this item to set or change the supervisor password. The Supervisor
Password item on top of the screen shows the default N o t I n s t a l l e d
d.
After you set a password, this item shows I n s t a l l e d
d.
To set a Supervisor Password:
1.
Select the Change Supervisor Password item and press <Enter>.
2.
From the password box, type a password composed of at least six
letters and/or numbers, then press <Enter>.
3.
Confirm the password when prompted.
The message “Password Installed” appears after you successfully set your
password.
To change the supervisor password, follow the same steps as in setting a
user password.
To clear the supervisor password, select the Change Supervisor Password
then press <Enter>. The message “Password Uninstalled” appears.
If you forget your BIOS password, you can clear clear it by erasing the
CMOS Real Time Clock (RTC) RAM. See section “1.9 Jumpers” for
information on how to erase the RTC RAM.
2-32
Chapter 2: BIOS setup
After you have set a supervisor password, the other items appear to allow
you to change other security settings.
Security Settings
Supervisor Password
User Password
: Not Installed
: Not Installed
Change Supervisor Password
User Access Level
Change User Password
Clear User Password
Password Check
[Full Access]
[Setup]
User Access Level (Full Access]
This item allows you to select the access restriction to the Setup items.
Configuration options: [No Access] [View Only] [Limited] [Full Access]
N o A c c e s s prevents user access to the Setup utility.
V i e w O n l y allows access but does not allow change to any field.
L i m i t e d allows changes only to selected fields, such as Date and
Time.
F u l l A c c e s s allows viewing and changing all the fields in the Setup
utility.
Change User Password
Select this item to set or change the user password. The User Password
item on top of the screen shows the default N o t I n s t a l l e d
d. After you set
a password, this item shows I n s t a l l e d
d.
To set a User Password:
1.
Select the Change User Password item and press <Enter>.
2.
On the password box that appears, type a password composed of at
least six letters and/or numbers, then press <Enter>.
3.
Confirm the password when prompted.
The message “Password Installed” appears after you set your password
successfully.
To change the user password, follow the same steps as in setting a user
password.
Clear User Password
Select this item to clear the user password.
ASUS P5S800-VM
2-33
Password Check [Setup]
When set to [Setup], BIOS checks for user password when accessing the
Setup utility. When set to [Always], BIOS checks for user password both
when accessing Setup and booting the system.
Configuration options: [Setup] [Always]
2.7
Exit menu
The Exit menu items allow you to load the optimal or failsafe default values
for the BIOS items, and save or discard your changes to the BIOS items.
Exit Options
Exit & Save Changes
Exit & Discard Changes
Discard Changes
Load Setup Defaults
Pressing <Esc> does not immediately exit this menu. Select one of the
options from this menu or <F10> from the legend bar to exit.
Exit & Save Changes
Once you are finished making your selections, choose this option from the
Exit menu to ensure the values you selected are saved to the CMOS RAM.
An onboard backup battery sustains the CMOS RAM so it stays on even
when the PC is turned off. When you select this option, a confirmation
window appears. Select Y e s to save changes and exit.
2-34
Chapter 2: BIOS setup
If you attempt to exit the Setup program without saving your changes,
the program prompts you with a message asking if you want to save
your changes before exiting. Press <Enter> to save the changes while
exiting.
Exit & Discard Changes
Select this option only if you do not want to save the changes that you
made to the Setup program. If you made changes to fields other than
System Date, System Time, and Password, the BIOS asks for a confirmation
before exiting.
Discard Changes
This option allows you to discard the selections you made and restore the
previously saved values. After selecting this option, a confirmation appears.
Select Y e s to discard any changes and load the previously saved values.
Load Setup Defaults
This option allows you to load the default values for each of the
parameters on the Setup menus. When you select this option or if you
press <F5>, a confirmation window appears. Select Y e s to load default
values. Select E x i t & S a v e C h a n g e s or make other changes before
saving the values to the non-volatile RAM.
ASUS P5S800-VM
2-35
2-36
Chapter 2: BIOS setup
This chapter describes the contents
of the support CD that comes with
the motherboard package.
3
Software
support
ASUS P5S800-VM
3-1
3.1
Installing an operating system
This motherboard supports Windows® 98SE/ME/2000/XP/2003 Server
operating systems (OS). Always install the latest OS version and
corresponding updates to maximize the features of your hardware.
3.2
•
Motherboard settings and hardware options vary. Use the setup
procedures presented in this chapter for reference only. Refer to
your OS documentation for detailed information.
•
Make sure that you install Windows® 2000 Service Pack 4 or the
Windows® XP Service Pack 1 or later versions before installing the
drivers for better compatibility and system stability.
Support CD information
The support CD that came with the motherboard package contains the
drivers, software applications, and utilities that you can install to avail all
motherboard features.
The contents of the support CD are subject to change at any time
without notice. Visit the ASUS website(www.asus.com) for updates.
3.2.1
Running the support CD
Place the support CD to the optical drive. The CD automatically displays the
D r i v e r s menu if Autorun is enabled in your computer.
Click an icon to
display support
CD/motherboard
information
Click an item to install
If A u t o r u n is NOT enabled in your computer, browse the contents of
the support CD to locate the file ASSETUP.EXE from the BIN folder.
Double-click the A S S E T U P . E X E to run the CD.
3-2
Chapter 3: Software support
3.2.2
Drivers menu
The drivers menu shows the available device drivers if the system detects
installed devices. Install the necessary drivers to activate the devices.
SIS Chipset Driver
Installs the SIS Chipset driver. When installed to the target system, this
driver provides the method for configuring the chipset components.
SIS AGP Driver
Installs the SIS AGP driver.
SIS Onboard Graphics Driver
Installs the onboard SIS graphics driver.
Realtek ALC655 Audio Driver
Executes the wizard to install the Realtek® ALC655 audio driver and
application.
SIS RAID Controller Driver
Installs the SIS RAID controller driver.
Realtek RTL8139 Ethernet Device Driver
Installs the Realtek® RTL8139 Ethernet device driver.
USB 2.0 Driver
Installs the USB 2.0 driver.
ASUS P5S800-VM
3-3
3.2.3
Utilities menu
The Utilities menu shows the applications and other software that the
motherboard supports.
ASUS PC Probe
This smart utility monitors the fan speed, CPU temperature, and system
voltages, and alerts you of any detected problems. This utility helps you
keep your computer in healthy operating condition.
ASUS Update
The ASUS Update utility allows you to update the motherboard BIOS in a
Windows® environment. This utility requires an Internet connection either
through a network or an Internet Service Provider (ISP). See page 2-8 for
details.
Microsoft DirectX
Installs the Microsoft® DirectX 9.0b driver.
Anti-Virus Utility
Installs the PC-cillin anti-virus program. View the online help for detailed
information.
ADOBE Acrobat Reader
Installs the Adobe® Acrobat® Reader V5.0.
ASUS Screen Saver
Installs the ASUS screen saver.
3-4
Chapter 3: Software support
3.2.4
ASUS Contact information
Click the C o n t a c t tab to display the ASUS contact information. You can
also find this information on the inside front cover of this user guide.
ASUS P5S800-VM
3-5
3-6
Chapter 3: Software support
Download PDF