Dacor | DHW482 | Product specifications | Dacor DHW482 Product specifications

M i l len n ia™ Wa l l
H o o ds
For use with models:
Part No. 101743 Rev. B
DHW301
DHW361
DHW421
DHW482
I n sta l l ati o n I n stru c ti o n s
M o u nt R an g e
Table
of
Important Safety Instructions........................................... 1
Product Specifications................................................... 3-4
General Specifications........................................................ 3
Dimensions.......................................................................... 3
Preparing for Installation..................................................... 4
Electrical Power Supply Installation.................................... 4
Plan and Install the Duct Work............................................ 4
Contents
Installation Instructions................................................ 6-11
Verify the Package Contents............................................... 6
Mounting Bracket Installation.............................................. 7
Chimney Mounting Bracket Installation............................... 7
Hanging the Range Hood................................................... 8
Final Installation.................................................................. 9
Verifying Proper Operation................................................ 10
Installation Checklist..........................................................11
Notes................................................................................. 12
Before You Begin...
IMPORTANT:
•
•
INSTALLER: In the interest of safety and to minimize
problems, read these installation instructions
completely and carefully before you begin the
installation process. Leave these installation
instructions with the customer.
If you have questions or problems with installation, contact
your Dacor dealer or the Dacor Customer Service Team.
Dacor Customer Service Team
Phone: (800) 793-0093
Web site: www.Dacor.com
CUSTOMER: Keep these installation instructions for
future reference and the local electrical inspector’s use.
All specifications are subject to change without notice. Dacor assumes no liability for changes to specifications.
© 2007 Dacor, all rights reserved
Important Safety Instructions
Important Information About Safety
Instructions
Safety Symbols and Labels
The Important Safety Instructions and warnings in these
instructions are not meant to cover all possible problems
and conditions that can occur. Use common sense and
caution when installing, maintaining or operating this or any
other appliance.
Always contact the Dacor Customer Service Team about
problems and conditions that you do not understand.
DANGER
Immediate hazards which WILL result in severe
personal injury or death.
WARNING
Hazards or unsafe practices which COULD result in
severe personal injury or death.
CAUTION
Hazards or unsafe practices which COULD result in
minor personal injury or property damage.
DANGER
IMPORTANT: If you smell gas:
• Do not use or light any appliance.
• Do not touch any electrical switch or use any electrical devices, including the telephone, in your building.
• From a neighbor’s phone, immediately call the gas supplier. Follow the gas supplier’s instructions.
• If you cannot contact the gas supplier, call the fire department.
IMPORTANT: Do not store or use combustible, flammable or explosive vapors and liquids (such as gasoline) on or in
the vicinity of this or any other appliance. Also keep items that could explode, such as aerosol cans, away from the
cooktop. Do not store flammable or explosive materials in adjacent cabinets or areas (including above and below the
cooktop).
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
a) Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer.
b) Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to
prevent power from being switched on accidentally. When the service disconnecting means cannot be locked,
securely fasten a prominent warning device, such as a tag, to the service panel.
READ AND SAVE THESE INSTRUCTIONs
1
Important Safety Instructions
To reduce the risk of fire, electric shock, serious injury or death when using your range hood, follow basic
safety precautions, including the following:
WARNING
1. Do not install or operate this hood if it has been damaged, dropped, has damaged electrical conduit or wires or is
not working properly. If the product is damaged when received, immediately contact the dealer or builder.
2. Use this range hood only for its intended purpose as outlined in the use and care manual. Do not use this range
hood to vent hazardous or explosive materials or vapors. If you have questions, contact the manufacturer.
3. The customer should not install, repair or replace any part of the range hood unless specifically recommended in
the literature accompanying it. A qualified service technician should perform all other service. Contact the nearest
Dacor authorized service representative at (800) 793-0093, or at www.Dacor.com for examination, repair or
adjustment.
4. Keep all packaging materials away from children. Plastic bags can cause suffocation.
5. This range hood must be installed and grounded by a qualified installer according to these installation
instructions. All installation work and electrical wiring must be performed in accordance with all applicable codes
and standards, including fire-rated construction.
6. Install or locate this appliance only in accordance with these installation instructions and the requirements
specified by the manufacturer of the cooktop or range. Improper installation, adjustment, alteration, service or
maintenance can cause serious personal injury or property damage.
7. Do not use an extension cord or adapter plug with this appliance.
8. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning
equipment to prevent back drafting. Follow the heating equipment manufacturer’s guidelines and safety standards
such as those published by the National Fire Protection Association (NFPA), and the American Society for
Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.
9. When cutting or drilling into the wall or ceiling, do not damage electrical wiring and other hidden utilities.
10. The installer must show the customer the location of the fuse or junction box so that the customer knows where
and how to turn the power off.
11. Before installing or servicing the range hood, switch power off at the fuse or junction box and lock the electrical
panel door to prevent power from being switched on accidentally. When the electrical panel cannot be locked,
securely fasten a prominent warning device, such as a tag, to the service panel.
12. Read the use and care manual completely before using the appliance.
13. Do not tamper with the controls.
14. Never allow the filter(s) to become blocked or clogged. Do not allow foreign objects, such as cigarettes or
napkins, to be sucked into the hood.
15. Clean the filter(s) and all grease-laden surfaces often to prevent grease fires and maintain performance.
16. If the cooktop and range hood are near a window, use an appropriate window treatment. Avoid long drapes or
other window coverings that could blow over the cooktop and hood, resulting in a fire hazard.
17. Always run the blower(s) whenever the cooktop is operating.
18. Never leave the range or cooktop unattended when a burner (or element) is in use. Boil-overs and greasy spills
may smoke and/or ignite.
19. Do not leave children alone or unattended in the area where the cooktop and range hood are in use. Never allow
children to sit or stand on an appliance. Do not let children play with a range, cooktop or range hood. Do not
store items of interest to children above or around the cooktop, range or range hood.
20. The minimum vertical distance between the cooktop surface and the exterior part of the hood must be no less
than 30” (762 mm). The vertical distance may be longer for the range or cooktop being used. Consult the range
or cooktop installation instructions for the minimum and maximum vertical distance from the appliance being
used.
21. A minimum of two people are required to safely install this appliance.
2
Important Safety Instructions
WARNING
22. TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE:
a. SMOTHER FLAMES with a close-fitting lid, cookie sheet or metal tray, then turn off the burner. BE CAREFUL
TO PREVENT BURNS. If the flames do not go out immediately, EVACUATE AND CALL THE FIRE
DEPARTMENT.
b. NEVER PICK UP A FLAMING PAN - you may be burned.
c. DO NOT USE WATER, including wet dish cloths or towels - a violent steam explosion may result.
d. Use a fire extinguisher ONLY if:
•
You have a Class ABC extinguisher, and you already know how to operate it.
•
The fire is small and contained in the area where it started.
•
The fire department is being called.
•
You can fight the fire with your back to an exit.
Product Specifications
General Specifications
Dimensions
ALL MODELS
Blower
600 CFM (1200 for units with 2 blowers)
with electronic speed control
Tolerances: +1/16”, -0
(+1.6 mm, -0), unless otherwise stated
Blower Speeds 4
Lights
12 Vac, 20W halogen
Filters
Baffle type, dishwasher safe
Exhaust
Finish
8-inch
430 stainless steel
Voltage
120 Vac, 60 Hz (see below for current
rating)
Circuit
Requirement
120 Vac, 15 Amp grounded, dedicated
circuit, minimum
MODEL SPECIFIC
MODEL NUMBER
DHW301 DHW361 DHW421 DHW482
Blowers
1
1
1
2
Lights
2
2
3
4
Filters
1
1
1
2
Maximum
Current Draw
3.38 A
3.38 A
3.55 A
6.75 A
* 18” 1/4 on 48-inch model (DHW482) with exhaust cowling
IMPORTANT: The minimum installed distance from the
hood to the cooktop surface must be no less than 30
inches. The minimum specified distance may be higher
for the particular range or cooktop in use. Check the
manufacturers specifications for the cooktop or range.
3
Preparing
for Installation
WARNING
•
The electrical service to the range hood should be installed only by a licensed electrician.
•
Observe all governing codes and ordinances during
planning and installation. Contact your local building
department for further information.
•
A qualified technician must complete the installation
of this built-in appliance. The owner is responsible to
make sure the hood is properly installed.
Carefully check the location where the hood is to be
installed. The hood should be placed for convenient
access. Make certain that electrical power can be provided
in the selected location.
Plan the installation so that all minimum dimensions are
met or exceeded (see page 3). Dimensions shown provide
minimum clearances, unless otherwise noted.
Plan
Electrical Power Supply
Installation
Electrical Specifications
Duct Work
WARNING
•
To reduce the risk of fire and to properly exhaust
air, be sure to duct air outside the house or building.
Do not vent exhaust air into spaces within walls or
ceilings or into attics, crawl spaces or garages.
•
Tape all duct joints securely to prevent combustion
by-products, smoke or odors from entering the home.
Doing so will also improve system efficiency.
•
Do not exhaust more than one vent into a single duct
run.
•
Use only duct work constructed of materials deemed
acceptable by state, municipal and local codes.
•
Range hoods may interrupt the proper flow of
smoke and combustion gases from furnaces, gas
water heaters and fireplaces. To avoid drawing
lethal gases into the home, follow the manufactures
recommendation for these devices and consult NFPA
and ASHRAE recommendations.
•
DO NOT install an additional in-line or external
blower to increase the length of the duct run. Even
small differences between blower air flow rates can
greatly reduce the air draw by the hood.
All contact surfaces between the hood and any cabinets or
walls must be solid and at right angles.
Install the range hood and cooking appliance(s) so that
they can be removed if service is required.
and Install the
•
All duct work materials (including screws and duct tape)
must be purchased separately by the customer. When
planning new duct work, always look for the shortest,
most direct route to the outside. Venting can be done
through the roof or directly through the back wall to the
outside.
•
The hood exhaust connects to an 8-inch round duct.
You can increase the duct size over the duct run if
desired. To prevent a back draft, never decrease the
duct size over the run.
•
Do not rely on duct tape alone to seal duct joints.
Fasten all connections with sheet metal screws and
tape all joints with certified silver tape or duct tape.
Use sheet metal screws as require to support the duct
weight.
•
To prevent back-drafts, a damper at the duct outlet may
also be required.
•
Make sure duct work does not interfere with floor joists
or wall studs.
It is the owner’s responsibility to ensure that the electrical
connection of this appliance is performed by a qualified
electrician. The electrical installation, including minimum
supply wire size and grounding, must be in accordance
with the National Electric code ANSI/NFPA* (or latest
revision) and local codes and ordinances.
*A copy of this standard may be obtained from:
National Fire Protection Association
1 Batterymarch Park
Quincy, Massachusetts 02269-9101
Installing the Electrical Connection
The electrical connection box must be:
•
•
4
Connected to a 120 Vac, 60 Hz dedicated, grounded,
circuit protected by a 15 Amp circuit breaker or time
delay fuse.
Located a minimum of 17” (43 cm) above the bottom of
the range hood.
Preparing
for Installation
Calculating the Maximum Duct Run Length
The maximum straight duct length for the hood is 50
feet. For each elbow and transition added to the duct
work, a certain number of feet must be subtracted from
the maximum straight length to compensate for wind
resistance. To determine the length the duct work cannot
exceed, subtract all of the equivalent lengths of the elbows
and transitions listed below from 50 feet.
Duct Work Equivalent Lengths
DUCT PIECE
SUBTRACT
90° elbow (8” Dia.)
7 feet
45° elbow (8” Dia.)
3 feet
3 1/4” x 10” to 8” round
4 foot
Wall cap with damper
30 feet
Roof cap
30 feet
Duct Work Design Tips
•
Wherever possible, reduce the number of transitions
and turns to as few sharp angles as possible. Two
staggered 45° angles are better than one 90°.
•
Keep turns as far away from the hood exhaust as
possible, with as much space between each bend as
possible.
•
For best performance, use round duct instead of
rectangular, especially when elbows are required.
•
If multiple elbows are used, try to keep a minimum of
24” of straight duct between them.
•
Avoid “S” or “back to back” configurations of adjacent
elbows.
•
In regions where the weather gets extremely cold,
thermal breaks, such as a short section of non-metallic
duct, should be used to avoid indoor heat loss. The
break should be located as close to the pass through
point to the outside as possible.
•
Do not use flexible metal duct.
•
Do not use duct work that is smaller in cross-sectional
area than the recommended size duct (8” round).
Duct Work Installation
Install all of the duct work, except for the portion that
will be located inside the hood chimney:
1. Determine the vertical center line for the range hood.
The center line for the hood is usually the same as the
center line of the range or cooktop.
2. Using a pencil, mark the vertical center line on the wall
from where the bottom of hood will be located to where
the top of the chimney will be located.
3. Draw a horizontal line 24 inches long at 90° to the
vertical center line where the bottom of the hood will be
located. The minimum allowable distance from the top
of the cooktop to the bottom of the hood is 30”.
4. Install the duct work so that the connection to the hood
will be centered on the hood’s center line. Also allow
for a 1” clearance between the duct work and the wall
where the hood will be mounted. The 1” clearance will
allow room for the chimney mounting bracket on the
ceiling.
5
Verify
Installation Instructions
the
Package Contents
Unpack the parts box and verify that all required
components have been provided. If any item is missing or
damaged, please contact the dealer immediately. Do not
install a damaged or incomplete appliance.
A
Hood assembly with filter(s)
B
Chimney assembly (2 piece)
C
Chimney mounting bracket
D
Mounting bracket*
E
Blower exhaust cowling (2 blower units only)
F
Mounting and assembly hardware
G
Use and care manual
* NOTE: The mounting hardware
included with the hardware packet
is suitable for mounting to brick
and masonry only. If mounting the
range hood to drywall, Dacor strongly recommends the
using a sturdy anchoring system
designed for use with drywall.
In addition, Dacor strongly
recommends that you install a
reinforced mounting block between
the studs behind all hood mounting
locations.
A
B
Make sure you have everything
necessary for proper installation
before proceeding.
C
E
D
F
G
6
Installation Instructions
If mounting the hood to drywall:
WARNING
•
The electrical service to the range hood should be installed only by a licensed electrician.
•
Do not install the range hood unless the electrical
service provided meets the range hood specifications.
•
Observe all governing codes and ordinances during
planning and installation. Contact your local building
department for further information.
•
A qualified technician must complete the installation
of this built-in appliance. The owner is responsible to
make sure the hood is properly installed.
•
To avoid an electric shock hazard and property
damage, locate electric wires and water pipes and
avoid drilling in the vicinity.
•
Drill three appropriate sized pilot holes for the
mounting hardware being used. The drywall
mounting hardware must be purchased separately.
MOUNTING BRACKET
Mounting Bracket Installation
1. Measure the distance between the bottom of the hood
and the mounting bracket hole on the hood being
installed. Using a pencil, draw a short line on the wall
the same distance above the horizontal line previously
drawn on the wall.
MOUNTING BRACKET
HOLE
6. Attach the mounting bracket securely to the wall (3
places).
Chimney Mounting Bracket
Installation
1. Locate the chimney mounting bracket and position it
against the ceiling as shown. Center it on the center
line drawn on the wall.
2. Find the mounting bracket in the shipping box. Put
the bracket against the wall and line up the top of the
bracket with the short line just drawn.
MOUNTING BRACKET
2. Mark the ceiling and the wall in two places each,
through the holes in the bracket. Remove the bracket
from the ceiling.
3. Drill four 5/16” holes through the four spots marked on
the ceiling and wall.
4. Insert the four of the provided wall anchors into the four
holes on the ceiling and wall.
ANCHOR
ANCHOR
CHIMNEY
MOUNTING
BRACKET
3. Line up the vertical line drawn on the wall with the
center hole on the bracket.
4. Mark the three mounting hole positions through the
holes in the bracket. Make sure they are level.
5. Drill the mounting holes...
If mounting the hood to brick or masonry:
•
Drill three 5/16” X 1 1/2” holes in the locations
marked.
•
Insert three of the provided wall anchors into the
holes. The anchors provided are for attaching the
hood to masonry or brick only.
5. Place the chimney mounting bracket against the ceiling
and attach it using four included 1 1/2” screws.
7
Hanging
Installation Instructions
the
Range Hood
warning
•
Hanging the range hood requires two people. Do not
attempt to lift the hood without assistance.
1. Attach the hood junction box to the top of the hood
using two machine screws as shown.
4. Insert two provided machine screws into the two holes
above the mounting bracket on the range hood. Tighten
the screws until they make contact with the bracket,
then tighten them as necessary to make minor leveling
adjustments to the hood.
5. Insert two machine screws through the front of the
mounting bracket and tighten them into place.
2. Remove the filter(s) to reduce weight and avoid
damage.
3. Lift the hood up on both sides and put the mounting
hole on the top of the hood over the lip of the mounting
bracket. Gently lower it into place.
MOUNTING
BRACKET
8
6. On models with two blowers: Put the exhaust cowling
over the blower outlets on the top of the hood. Fasten
the cowling in place with 14 machine screws.
Installation Instructions
7. Inside the exhaust outlet(s) there are metal or plastic
damper flaps. The flaps close to help prevent backdrafts when the blower is turned off. Remove the
shipping tape and make sure all the flaps open and
close freely before proceeding.
Final Electrical Installation
WARNINGS
•
To avoid electrical shock or fire hazard, make sure
the power supply at the fuse or junction box is turned
off before proceeding with final installation.
•
Improper connection of the hood electrical wiring may
create an electric shock or fire hazard and may result
in damage to the hoods electrical system.
•
Do not ground the hood to the neutral (white) power
supply wire. Connect the hood ground wire to a
separate, properly grounded wire installed by a
licensed electrician.
Connect the house power supply wires to the wires
coming out of the top of the hood junction box:
1. Connect the white wire from the hood to the neutral
(white) power supply wire.
2. Connect the black wire from the hood to the hot (black)
power supply wire.
Final Installation
3. Connect the green and yellow wire from the hood to
the house ground (green) wire from the junction box.
Connecting to the Duct Work
warning
•
•
Do not use screws to attach the duct work to the
hood exhaust outlet. Use duct tape only. Screws may
prevent the damper flaps on the top of the hood from
opening.
Install the last of the duct work between the hood
exhaust and the previously installed duct work. Attach
the duct to the hood exhaust with duct tape alone. Use
sheet metal screws (not provided) and duct tape on the
remaining joints.
black to black
white to white
Yellow/green
to green
9
Installation Instructions
Installing the Chimney
IMPORTANT: Be careful not to pinch the electrical wires
while installing the chimney.
1. Remove the protective plastic covering from both
pieces of the chimney assembly. Do not remove the
protective tape strips from the inside of the chimney.
They protect the telescoping pieces from scratching
during installation.
2. Carefully slide both sections together so that only the
vents on the top section show.
Verifying Proper Operation
1. Turn on power at the junction or fuse box.
2. If the control panel is not lit, remove the filter(s) and
turn on the main power switch located behind the filters
on the bottom of the hood. Replace the filter(s).
3. Touch the light key. Verify that all the lights come on.
4. Touch the light key again to turn the lights off.
3. Hold the chimney vertically with the vents up.
5. Touch the blower “+” key once and release. Verify that
one light is showing on the blower speed indicator and
that the blower is on at low speed.
4. Carefully put the chimney over the top of the duct work
extending out of the top of the hood, taking care not to
scratch the surfaces. Make sure the wiring is tucked in
behind the chimney.
6. Touch and release the blower “+” repeatedly, three
times. Verify that with each touch of the key the number
of lights on the blower speed indicator increases and
that the blower speed increases.
duct work
7. Touch and hold the blower “-” key until the blower
turns off.
If the hood fails to operate properly:
CHIMNEY
mounting
BRACKET

vent
Verify that power is supplied to the hood.
•
Check the electrical connections to ensure that the
installation has been completed correctly.
•
Repeat the above test.
•
If the appliance still does not work, contact an
authorized Dacor service company at (800) 793-0093.
Do not attempt to repair the appliance yourself. Dacor
is not responsible for service required to correct a faulty
installation.

CHIMNEY

hood
5. Move the chimney up toward the ceiling. Line up the
holes on the side of the chimney, above the vents, with
the holes on the side of the chimney mounting bracket.
6. Attach the sides of the chimney to the bracket using
two sheet metal screws, one on each side.
7. Carefully, slide the bottom portion of the chimney down
until it rests on the top of the range hood.
Reinstall the range hood filter(s) before operation.
10
•
Installation Instructions
Installation Checklist
WARNING
•
To ensure a safe and proper installation, the following
checklist should be completed by the installer to
ensure that no part of the installation has been
overlooked.
•
Proper installation is the responsibility of the
homeowner. The importance of proper installation of
your Dacor range hood cannot be overemphasized.
□□
Is the mounting bracket properly attached to the wall
according to the instructions on page 7?
□□
Is the hood properly tightly secured to the mounting
bracket with the machine screws (see page 8)?
□□
Is the duct work completely installed? Are all joints
attached with sheet metal screws and wrapped with
duct tape (see pages 4 and 9)?
□□
Is the range hood wired and grounded according to
these instructions and in accordance with all applicable
electrical codes (see page 9)?
□□
Are the filters properly installed according to the use
and care manual?
□□
□□
Has proper operation been verified (see page 10)?
Have any problems been noted on the warranty card
or during the on-line warranty activation? Has the
warranty been activated on-line or the warranty card
filled out completely and mailed?
11
Notes
12
Dacor ● 1440 Bridge Gate Drive, Diamond Bar, CA 91765 ● Tel: (800) 793-0093 ● FAX: (626) 403-3130 ● www.Dacor.com
Download PDF