Start Here Easy Setup Instructions 6 Lower the lock lever. Click Thank you for purchasing the Canon PIXMA MP780/750. To prepare your machine for use, please follow these Easy Setup Instructions before referring to any other documentation. Lower the lock lever until you hear a click as it locks into place. IMPORTANT Do not connect the USB cable until after the software is installed. See the rear side of this sheet for details. 5 Install the ink tanks. 1 1 Unpack and install the machine. Remove the orange-colored protective film. If it is not removed completely, problems with printing may occur. Check the package contents. • Machine • Power cord • Print head Prepare the ink tanks. Remove the protective cap and discard it. • Telephone line Do not touch! 2 Insert the ink tanks. Click MP780 MP750 • Ink tanks Black BCI-3eBK Black Cyan Magenta Yellow BCI-6BK BCI-6C BCI-6M BCI-6Y Push it in until locks into place. • Easy Setup Instructions • Quick Start Guide • Setup CD-ROM The Setup CD-ROM contains the MP Drivers, as well as the User's Guide, Software Guide and Photo Application Guide in electronic format. Please read these guides. 3 Bad example: Tank 6BK is not fully inserted. Make sure to press it down firmly. Good example Close the Inner Covers and the Scanning Unit. Click • In this sheet, illustrations of MP780 are shown. • A printer cable is not included. You must purchase a USB cable (less than 16 3/8 ft.) to connect your machine to a computer. Click 2 Connect the telephone line. (MP780 model only) Connect external devices as follows: External device jack Telephone line jack Telephone or answering machine Machine Close the two Inner Covers. IMPORTANT Be sure to hold the Scanning Unit firmly with one hand. Connect the telephone line and any necessary external device. For details, see the Quick Start Guide. Telephone line 6 Load the paper. 1 2 Open the Auto Sheet Feeder. Load two sheets or more of letter-size plain paper. (1) Open the Auto Sheet Feeder. Telephone or answering machine Built-in computer modem and telephone Connect the telephone line cord to the wall jack. You can connect an external device (telephone or answering machine) if necessary. Telephone line Machine LINE TEL Computer Telephone 3 Connect the power cord. 1 Connect the power cord. If the message <PUT IN CARTRIDGE> appears, go to Step 4, "Install the print head." Lift the Scanning Unit. (2) Press [OK]. 3 (3) The machine will print the print head position pattern and automatically align the print head. If this message does not appear after closing the Scanning Unit, see "Aligning The Print Head Automatically" in the Quick Start Guide. Click Raise the lock lever. Touch only the lock lever! (3) Install the print head here. If the printed pattern matches the illustration, print head alignment is complete. You can change the language displayed on the LCD. Raise this securely. (1) Open the two Inner Covers. Prepare the print head. Press [OK] to start print head alignment. Pull the Scanning Unit Lever. (2) The Print Head Holder moves to the center. 4 1 ALIGN PRINT HEAD PRESS [OK] Press the Open Button to open the Press the Open Button. Paper Output Tray. Then lift the Scanning Unit until it locks into place. Open the two Inner Covers. Be sure to align the print head to ensure print quality. (1) This message appears. IMPORTANT Be sure to hold the Scanning Unit firmly with one hand. 2 Ensure the paper stack does not exceed the paper limit mark. 7 Align the print head from the Operation Panel. 4 Install the print head. 1 Load the paper with the print side face up. Pinch and adjust the paper guide to the width of the stack. (2) Pull out the Paper Support until it stops. 1. Connect one end of the power cord to the rear of the machine. 2. Connect the other end to the AC outlet. 2 Pull the Scanning Unit Lever towards you to close the Scanning Unit. For details, see "Selecting The Language For The LCD" in the Quick Start Guide. You have completed installation and alignment. 5 Insert the print head. If you are connecting the machine to a computer for use, see the rear side of this sheet for instructions on installing the software. (2) Push back. Do not touch! (1) Insert. Remove the protective cap and discard it. © 2004 Canon U.S.A., Inc., Canon and BCI are registered trademarks and PIXMA is a trademark of Canon Inc. All other products and brand names are registered trademarks or trademarks of their respective owners. Specifications subject to change without notice. HT7-0029-000-V.1.0 xx2004A © CANON INC. 2004 PRINTED IN CHINA Install the software. The following software programs are included on the Setup CD-ROM: Select Easy Install in order to install the application software, electronic manual and MP drivers. Select Custom Install in order to choose the options you would like to install. This sheet explains Easy Install Only. IMPORTANT • If you have an earlier version of the MultiPASS Suite software installed on your computer, uninstall this version before installing the new version. For instructions on uninstallation, see the guides for that version of MultiPASS Suite. • Close any open software applications, including virus checkers, prior to installing the software. On-screen Manual MP Drivers Easy-PhotoPrint ScanSoft OmniPage SE MP Navigator IMPORTANT • Do not connect the machine to Mac OS 9 or Mac OS X Classic environments since they are not supported. • Before installing the software, you must log on as a user with Administrator privileges. Step 1: Connect the USB cable. • Make sure the machine is turned ON. The following software programs are included on the Setup CD-ROM: On-screen Manual MP Drivers MP Navigator Easy-PhotoPrint Easy-WebPrint ScanSoft OmniPage SE Presto! PageManager IMPORTANT • Do not connect the USB cable until Step 3, “Connect the USB cable.” • Before installing the software in Windows 2000, you must log on as Administrator or a user with Administrator privileges, and before installing the software in Windows XP, you must log on as Administrator. Step 1: Prepare the Setup CD-ROM and Get Ready to Install. 1 Turn ON your computer, and start Windows. 2 Insert the Setup CD-ROM into the CD-ROM drive. Step 2: Prepare the Setup CD-ROM. 1 Turn ON your computer, and start Mac OS X. 2 Insert the Setup CD-ROM into the CD-ROM drive. 3 Double-click [Setup] on the Setup CD-ROM, or click [Setup] on the Setup CDROM and click [File] menu and then select [Open]. Step 3: Enter the name and password for an Administrator Account. 1 Enter the name for Administrator. 2 Enter the password and then click [OK]. • The setup program should automatically run. If the setup program does not automatically run, click [My Computer], then double-click [setup] on the Setup CD-ROM. IMPORTANT If the following screen appears, the USB cable is connected. Enter Click Step 4: Install the software. 1 Click [Easy Install], then click [Install]. z Perform the following steps. 1. Disconnect the USB cable. • To read descriptions of the software programs, click the 2. Click [Cancel]. • To read restrictions of the software programs, click the icon. icon. Click Step 2: Install the software. 1 Click [Easy Install], then click [Install]. Click • To read descriptions of the software programs, click the • To read restrictions of the software programs, click the icon. icon. Click 2 Click 3 Click [Yes]. • Installation begins. Click [Continue]. • Follow the displayed instructions. Click 2 3 Click [Yes]. • Installation begins. Click [Continue]. • Follow the displayed instructions. Click 4 Click 4 Click Click [Restart] to restart your computer. Click Click Click [Exit]. • If prompted to, restart your computer. Click Step 3: Connect the USB cable. • Make sure both your machine and the computer are turned ON. • When you connect the USB cable, the computer will automatically detect and configure any necessary settings. In Windows 2000, the machine may not be set as the default printer. [MP780 FAX] is shown in the Name list, but you cannot add [MP780 FAX]. You can fax the document with the current print settings applied to it using the computer's internal modem. You cannot send faxes from your computer via the machine.