Montigo | H-Series DF | Owner`s manual | Montigo H-Series DF Owner`s manual

www.montigo.com
Installation Operation & Maintenance Manual
Check local codes and read all instructions prior to installation.
H-Series DL Gas Fireplace
H34DL Indoor
H38DL Indoor
H42DL Indoor
Warning:
If the information in these instructions is not
followed exactly, a fire or explosion
may result causing property damage, personal injury or death.
H38DL Shown
Warning:
WHAT TO DO IF YOU SMELL GAS
Improper installation, adjustment, alteration, service or maintenance can cause
injury or property damage. Refer to this manual. For assistance or additional
information consult a qualified installer, service agency or the gas supplier.
Safety Notice:
Glass doors on gas fireplaces are extremely hot while the fireplace is on and remain
hot even after the fireplace has been turned off. Safety screens are available and
can reduce the risks of severe burns. Please keep children away from the fireplace
at all times.
For Your Safety:
Do not store or use gasoline or other flammable vapors and liquids in the
vicinity of this or any other appliance.
®
C
XG0140
US
Canadian Heating Products Inc. Langley, BC V4W 4A
•
•
Do not try to light any appliance.
Do not touch any electrical
switch; do not use any phone in
your building.
• Immediately call your gas
supplier from a neighbor's
phone. Follow the gas supplier's
instructions.
• If you cannot reach your gas
supplier, call the fire department.
Installation and service must be
performed by a qualified installer,
service agency or the gas supplier.
• Installer: Leave this manual
with the appliance.
• Consumer: Retain this
manual for future reference.
Montigo Del Ray Corp. Ferndale, WA 98248
092210
H-Series DL Gas Fireplace
Table of Contents
Safety Alert Key
▪ Section 3-3-2: Venting Components.............................. 16
Introduction................................................................................ 3
▪ Section 3-3-3: Heat Shields.......................................... 17
▪ Installing a RHS8 Wall Mounted Heat Shield.......... 17
Installation
▪ Installing a RHS101 Wall Mounted Heat Shield. ..... 17
Before you Start.............................................................. 4
Section 4: Wiring.................................................................... 18
Installation Checklist....................................................... 4
▪ Honeywell gas control and pilot . ......................... 18
Section 1: Installation Overview and Product Dimensions....... 5
▪ SIT - IPI gas control and pilot. .............................. 18
▪ Installing HFK Fan Kit.......................................... 18
Models............................................................................ 3
Section 2: Framing the Fireplace.............................................. 6
Clearances...........................................................
Section 5: Installing the Gas Line........................................... 19
Installing the Standoffs.........................................
Section 5-1: Fuel Conversion......................................... 19
Section 3: The Direct Vent System....................................7 - 16
Section 5-2: Gas Pressure. ........................................... 19
Section 5-3: Gas Connection......................................... 19
Section 3-1: Converting from Top Vent to Rear Vent..... 7
Section 3-2: Installing a Roof mounted Termination.8 - 9
Section 6: Finishing................................................................ 20
▪ Section 3-2-1: Venting Layout....................................... 8
Section 7: Installing and Removing the Door......................... 21
▪ Roof mounted Terminations
Section 8: Installing the Accessories...............................22 - 24
Standard Top Vent (no elbows or offsets)............. 8
▪ Installing the H34DL Log Set.................................... 22
Top Vent (two elbows one offset).......................... 8
▪ Installing the H38DL & H42DL Log Set...............23 - 34
Top Vent (multi-elbows and offsets)...................... 8
▪ Installing the Top / Bottom Horizontal Louvers............ 24
Standard Roof Vent (one elbows no offsets)........ 9
Section 9: Operation........................................................25 - 27
▪ Section 3-2-2: Venting Components.............................. 9
Section 3-3: Installing a Wall mounted Termination..... 10
▪ Standard PTO Installation.................................... 10
▪ Pre-installed MSR Frame..................................... 10
Maintenance . ..................................................................28 - 30
▪ Pre-installed BSR Frame. .................................... 10
▪ General.................................................................. 28
▪ Installing MOSR Frame. ...................................... 10
▪ Cleaning. ............................................................... 28
▪ Installing VSS Termination Shield. ........................ 10
▪ Hi-Lo Burner Adjustment.......................................... 28
▪ Installing PTKOG Heat Guard. ............................. 10
▪ Pilot Burner Adjustment. .......................................... 28
▪ Start-up Sequence with Continuous Pilot................... 25
▪ Start-up Sequence with Honeywell Electronic Ignition.26
▪ Start-up Sequence SIT-IPI Gas valve........................ 27
▪ Section 3-3-1: Venting Layout.................................... 11
▪ Troubleshooting. ...................................................... 29
▪ Top Vent, Wall mounted Graph, H34DL. ................ 11
SIT- Nova 820 Gas Control Valve.......................... 29
▪ Top Vent, Wall mounted Graph, H38DL. ................ 11
SIT- IPI Electronic Gas Control Valve..................... 29
▪ Top Vent, Wall mounted Graph, H42DL. ................ 12
Honeywell Gas Control Valve................................ 29
▪ Top Vent, Wall mounted termination (one elbow)..... 12
▪ Parts List................................................................ 30
▪ Top Vent, Wall mounted termination (multi elbow).... 12
Appendix
▪ Rear Vent, Wall mounted Graph, H34DL. .............. 13
A. Termination Locations. ......................................... 31
▪ Rear Vent, Wall mounted Graph, H38DL. .............. 13
B. Warranty............................................................. 32
▪ Rear Vent, Wall mounted Graph, H42DL. .............. 14
C. State of Massachusetts........................................ 33
▪ Standard Rear Vent, (no elbows or offsets)............ 14
D. Mobile Home....................................................... 34
▪ Rear Vent, Wall mounted termination (two elbows). 14
▪ Rear Vent, Wall mounted termination (45° corner)... 15
▪ Rear Vent, Wall mounted termination (-45° corner).. 15
Page 2
Warning:
Read this manual before installing, operating or troubleshooting this appliance. Please retain this owner's
manual for future reference.
Part No. XG0140 - 092210
H-Series DL Gas Fireplace
Introduction
Safety Alert Key:
WARNING
HOT GLASS WILL
CAUSE BURNS.
DO NOT TOUCH GLASS
UNTIL COOLED.
NEVER ALLOW CHILDREN
TO TOUCH GLASS.
Warranty and Installation Information: (See Appendix B)
The Montigo warranty will be voided by, and Montigo disclaims any
responsibility for, the following actions:
► Modification of the fireplace and/or components including DirectVent assembly or glass doors.
►
Use of any component part not manufactured or approved by
Montigo in combination with this Montigo fireplace system.
►
Traditional Burner /
Logset
Contemporary
Burner w/River rock
Linear Burner w/
Glass Accessories
Standing Pilot
Ignition
Honeywell Hot
Surface Ignition
SIT Electronic
Ignition
With over 30 years of experience, Montigo is committed to providing
you with a gas fireplace that is not only a beautiful addition to your
space, but that is also designed and manufactured to the highest
safety, reliability and engineering standards.
We strongly encourage you to read and carefully follow the
instructions laid out in this Installation, Operation and Maintenance
Manual and retain it for your future reference. Pay special attention
to all cautions, warnings, and notices throughout this manual
intended to ensure your safety.
This manual covers installation, operation and maintenance.
Lighting, operation and care of this fireplace can be easily
performed by the homeowner. All installation and service work
should be performed by a qualified or licensed installer, plumber
or gasfitter as certified by the state, province, region or governing
body where the fireplace is being installed.
MODEL
INTRODUCTION
Congratulations on your purchase of a Montigo Fireplace.
Natural Gas
Liquid Propane
Gas Rating
(BTU hr)
• WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.
• CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
• NOTICE: Used to address practices not related to personal injury.
• Important: Used to address practices not related to personal injury.
H34DLN
X
18,000
X
H34DLNE
X
18,000
X
H34DLNI
X
18,000
X
H34DLM
X
18,000
X
X
X
H34DLL
X
18,000
X
H34DLLE
X
18,000
X
H34DLLI
X
18,000
X
H38DLN
X
26,000
X
H38DLNE
X
26,000
X
H38DLNI
X
26,000
X
H38DLL
X
26,000
X
H38DLLE
X
26,000
X
H38DLLI
X
26,000
X
H42DLN
X
34,000
X
H42DLNE
X
34,000
X
H42DLNI
X
34,000
X
H42DLL
X
32,000
X
H42DLLE
X
32,000
X
H42DLLI
X
32,000
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
This installation, operation and maintenance manual is applicable
to the models described below. Refer to your rating plate to
verify included options. Throughout this manual instructions are
applicable to all models designated as H*DL* unless otherwise
noted.
Installation other than as instructed in this manual.
Consult your local Gas Inspection Branch on installation requirements
for factory-built gas fireplaces. Installation & repairs should be done by
a qualified contractor.
Part No. XG0140 - 092210
Page 3
H-Series DL Gas Fireplace
Installation
IMPORTANT MESSAGE: SAVE THESE INSTRUCTIONS
The H*DL* Direct Vent fireplace must be installed in accordance
with these Instructions. Carefully read all the Instructions in this
manual first. Consult the Local Gas Branch to determine the need
for a permit prior to starting the installation. It is the responsibility
of the installer to ensure this fireplace is installed in compliance
with the manufacturers instructions and all applicable codes.
Installation Checklist
„„ Determine the desired install location of your fireplace.
„„ See Section 1, Dimensions on Page 5, and refer to the Framing
Section 2 for details.
„„ Select the location of your termination and resulting vent run.
„„ Your selected termination location must be the highest point
in the Direct Vent installation.
BEFORE YOU START:
„„ Should it be impossible to meet the venting requirements laid
out in Section 3: Venting, please contact Montigo regarding the
use of a Montigo Power Vent.
INSTALLATION AND REPAIRS SHOULD BE DONE
BY AN AUTHORIZED SERVICE TECHNICIAN. THE
APPLIANCE SHOULD BE INSPECTED BEFORE USE
AND AT LEAST ANNUALLY BY A PROFESSIONAL
SERVICE TECHNICIAN. MORE FREQUENT CLEANING
MAY BE REQUIRED DUE TO EXCESSIVE LINT
FROM CARPETING, BEDDING MATERIAL, ETC. IT
IS IMPERATIVE THAT CONTROL COMPARTMENTS,
BURNERS AND CIRCULATING AIR PASSAGEWAYS
OF THE FIREPLACE ARE KEPT CLEAN.
„„ Lay out the Vent run; calculating the required elbows and straight
runs of 4"/7" flex or rigid pipe.
CAUTION!
Due to its high operating temperatures, the appliance should
be located out of traffic & away from furniture and draperies.
 Children and adults should be alerted to the hazards
of the high surface temperature, which could cause
burns or clothing ignition.
 Young children should be carefully supervised when
they are in the same room as the appliance.
 Clothing or other flammable materials should not be
placed on or near the appliance.
„„ Layout Electrical Requirements Refer to Section 4: Wiring, for
Details.
„„ Refer to Section 5: Installing the Gas Line, for details on the
gas connection and access.
„„ Refer to local codes and guidelines for installation requirements.
„„ Installation and repairs should be done by a qualified
contractor and must conform to:
• Installations in Canada must conform to the current
CAN/CGA B-149.1 and .2 Gas Installation Code and local regulations.
• Installations in the USA must conform to local codes,
or in the absence of local codes to the National Fuel Gas Code, ANSI
Z223.1-1988.
• See Appendix C for installation within the State of
Massachusetts. This fireplace must comply with NFPA-54 Chapter
10.
WARNING!
When this appliance is installed directly on any combustible
material other than wood flooring, it must be installed on a
metal or wood panel extending the full width and depth of
the appliance.
Page 4
Part No. XG0140 - 092210
H-Series DL Gas Fireplace
Installation
Section 1: Installation Overview and Product Dimensions
Please review the Installation Checklist on Page 4 for general information on preparing for a successful installation of your fireplace.
The H*DL* fireplace may be installed in any location that maintains proper clearances to air conditioning ducts, electrical wiring and plumbing.
Safety, as well as efficiency of operation, should be considered when selecting the fireplace location. Try to select a location that does not interfere
with room traffic, has adequate ventilation and offers an accessible path for Direct Vent installation.
The fireplace dimensions are shown below:
H
K
J
J
I
CCLL
G
K
Top View
D
C
G
D
K
J
D
B
B
L
F
A
Front View
LH-Side View
A
B
C
D
E
F
G
H
I
J
K
L
H34DL*
33 /8
31 /2
31 /8
1
1 /4
21 /2
1
15 /4
3
21 /4
3
7 /4
4
7
25
H38DL*
37 /4
34 /2
34 /4
1
1 /4
24 /2
1
16 /4
25
1
9 /4
5
8
27 3/4
H42DL*
42 1/4
38 1/2
39 3/4
1 1/4
28 1/2
1
17 3/4
28 1/4
10 3/8
5
8
31 1/2
7
3
1
1
3
1
1
1
1
1
Figure 1. Fireplace dimensions, (ALL Models, shown in Table on Page 3).
Part No. XG0140 - 092210
Page 5
H-Series DL Gas Fireplace
Installation
Section 2: Framing
1). Frame in the enclosure for the unit with framing materials. The
framed opening for the assembled fireplaces are as shown below,
see Figure 2.
NOTE: When constructing the framed opening, please ensure
there is access to install the gas line when the unit is installed.
See Figure 22.
Combustible
Shelf
Combustible
Header
17 1/2”
Dimension for Top
PEL Shor t
vent fireplaces, see 90° elbow
graphs, figures 14, L
* 2” min.
15 & 16.
M
Exterior
Wall
Figure 4. Combustible Framing for shelves over the fireplace, Top
vent.
M”
Clearances
When installing a shelf over the top of the fireplaces, the following
guidelines must be adhered to:
N”
For Rear Vent applications, the minimum clearance is 2" from the rear
of the fireplace to a wall, or any combustible materials, and 9" clearance
from the top of the fireplace to the underside of any combutible shelf
materials.
O”
0" clearance
to corners only
For Top Vent applications, the minimum clearance is 2" from the rear of
the fireplace to a wall, or any combustible materials, and 17 1/2" to the
underside of any combustible shelf materials, Figure 4.
Q
S
T
H34DL*
37 1/4 33 3/4 17 7/8
52 3/8
37
31
41
H38DL*
40 1/4 37 3/4 18 7/8
57 1/2
40 5/8
34
44
H42DL*
44 1/4
63 3/4
45 1/8
38
48
42
19 3/8
Figure 2. Framing dimensions, (Straight wall & Corner Installation).
(ALL Models, shown in Table on Page 3).
Combustible
Shelf
2” min.
18” max.
"L" Dimension, see
table on Page 5.
*L
Combustible
Header
9”
S
9
17 1/2
2
1
0
4
Installing The Standoffs
To avoid elevated mantel temperatures, all H*DL*- Series gas
fireplaces are required to have the supplied standoffs installed.
The fireplace is supplied with two standoffs. Bend and install these
standoffs on top of the fireplace ensuring that the height of the standoff
maintains a MIN. 6" clearance.
6"
M
Exterior
Wall
Figure 3. Combustible Framing for shelves over the fireplace, Rear
vent.
Page 6
H*DL*
Mantel
P
Floor
O
Sides
N
Back
M
The fireplace clearances are shown below:
Top Top Vent
* When sheetrock is not used behind
the fireplace, framing depth "O" may be
reduced by 5/8".
For Top or Rear Vent applications where the Minimum mantel height
is required above the fireplace, (for an alcove or low profile shelf), ALL
Materials MUST BE NON-COMBUSTIBLE, Figure 5. The minimum
clearance is 2" from the rear of the fireplace to a wall, or any combustible
materials.
Top Rear Vent*
N”
P”
MODEL
Q”
Figure 6. Installing the standoff's.
Part No. XG0140 - 092210
H-Series DL Gas Fireplace
Installation
Section 3: Venting
Montigo supplies a variety of direct venting and termination options.
The direct vent termination location MUST be selected such that
it is the highest point in the venting assembly. It should also be
selected such that it provides the shortest vent run possible. Should
it be impossible to ensure that the termination is the highest point
or to meet the venting guidelines laid out below please contact your
Montigo dealer to discuss power venting options.
NOTES FOR PLANNING VENTING:
„„ Venting can originate from the unit through the top or
through the rear
„„ Venting can terminate through the roof or through an
exterior wall.
„„
Refer to Appendix A - Termination Locations to ensure the
planned termination location is acceptable.
„„ Once the termination location has been established, refer
to the appropriate section below for installation details
4.Install the (4/5" and 7/8") collars to the rear vent outlet using the
included hardware, as illustrated Figure 9a.
Flue Cover Plate
Flue Gasket
7” Outer Flue Collar, H34DL
8” Outer Flue Collar, H38DL & H42DL
4” Inner Flue Collar, H34DL
5” Inner Flue Collar, H38DL & H42DL
Figure 9a. Flue cover and collar installation, Rear Vented fireplace.
„„ All fireplaces shipped from the factory are Top vent.
See Section 3-1 for converting the unit from top vent to rear vent.
Section 3-1: CONVERTING TO REAR VENT
Use the following instructions to convert an H*DL* for Rear Vent use:
1.Remove the Rear flue cover and gasket (4/5" and 7/8") on the
flue outlet, as shown in Figure 9.
2.Next, Remove the Top flue collar's (4/5" and 7/8") on the flue
outlet, as shown in Figure 9.
3.Install the (removed) Rear flue cover and gasket material, to the
Top vent outlet. Fasten the cover with included hardware, as
illustrated Figure 9a.
4” Inner Flue Collar, H34DL
5” Inner Flue Collar, H38DL & H42DL
7” Outer Flue Collar, H34DL
8” Outer Flue Collar, H38DL & H42DL
Flue Gasket
Flue Cover Plate
Figure 9. Flue cover and collar removal, Top Vented fireplace.
Part No. XG0140 - 092210
Page 7
H-Series DL Gas Fireplace
Installation
Section 3-2: INSTALLING A ROOF MOUNTED DIRECT VENT
TERMINATION (MVTK-1 / PVTK-1)
This section applies to installations where the direct vent termination will be roof mounted.
PVTK1 / PVTK-1
MVTK-1
Termination
Termination
2’ min.
Section 3-2-1: VENTING LAYOUT
Support ring
Selection of components and details of venting lay out should
adhere to the following guidelines:
32’ max.
Support plate
Obstacle
„„ The maximum termination point is 32’ above the fireplace (NOTE:
if the maximum termination height is used, the flame pattern
may be affected).
Firestop
„„ The Vertical termination must be a minimum 2’ higher than where
the termination exits the roofing materials, (asphault shingles,
cedar shakes, etc). This distance should be measured from the
high side of the roof slope where the flue flashing intersects the
roofing materials. (see Figures 11 to 11c *).
„„ Termination location must be a minimum 6’ from a mechanical
air inlet.
„„ Termination location must be a minimum 18” from a parapet wall.
„„ A maximum of two offsets (each offset is made up of 2-90°
bends) may be made.
Figure 11a. Top vent, Roof mounted with 1 offset (1 offset= two 90°
bends).
„„ Install a firestop at any location where venting passes through
combustible materials and construction.
MVTK-1 / PVTK-1
PVTK1
Termination
Termination
„„ Utilize support straps, or support plates, and rings (as required)
to meet acceptable building practices.
2’ min.
„„ Install all roof flashing and storm collars as shown.
Support straps or
support plate & ring
Roof mounted Terminations
The following details are some possible configurations for Roof
mounted terminations. See below.
MVTK-1 / PVTK-1
PVTK1
Termination
Termination
2’ min.
Firestop
32’ max
Support plate
& ring
Support ring
32’ max.
Firestop
Support plate
Obstacle
2’
Firestop
Figure 11. Top vent, Roof mounted termination with no offset in
vent run.
Page 8
Firestop
Figure 11b.Top vent, Roof mounted with 2 offsets (1 offset= two 90°
bends).
Part No. XG0140 - 092210
H-Series DL Gas Fireplace
Installation
MVTK-1
PVTK1 / PVTK-1
Termination
Termination
Connection and installation of the vent components should
adhere to the following guidelines:
„„ Use any combination of rigid and Flex pipe as required.
MEXT/PEXT
Sections
Support plate
„„ Flex sections may be stretched up to 50% of their total length
(e.g. a 24” section maybe stretched to 36”).
„„ Connect all vent sections using a minimum of three sheet metal
screws on the outer pipe flue.
32’ max
Support ring
„„ Ensure the pipe ends male to female slide in a minimum of 1
1/2” of overlap.
„„ Ensure all runs are supported with a minimum of 3 supports per
10’ of venting.
„„ When hanging/ supporting venting, ensure that 1” clearance
is maintained on sides and bottom of vent runs and 2” above
horizontal vent runs to any combustible material.
„„ Ensure when cutting sections of rigid pipe to maintain integrity
of internal supports.
18”
Max.
Figure 11c.Rear vent, Roof mounted venting (1 = 90° bend).
Section 3-2-2: VENTING COMPONENTS
Select from the following components and associated Montigo
part numbers for installation of a Roof Mounted Termination.
Use only Montigo Vent Components. Use of non-Montigo parts
will void the warranty and may impede operation of the fireplace.
4" / 7" Venting
5" / 8" Venting
A - Termination
MVTK-1
B - Flex Sections
MFL - 1
MFL - 18
MFL - 2
MFL - 3
MFL - 4
MFL - 6
(12" f/f Section)
(18" f/f Section)
(24" f/f Section)
(36" f/f Section)
(48" f/f Section)
(72" f/f Section)
PFL - 1
PFL - 18
PFL - 2
PFL - 3
PFL - 4
PFL - 6
(12" f/f Section)
(18" f/f Section)
(24" f/f Section)
(36" f/f Section)
(48" f/f Section)
(72" f/f Section)
C - Rigid Sections
MXT - 5
MXT - 10
MEXT - 1
MXT - 20
MEXT - 2
MEXT - 3
MEXT - 4
MEXT - 6
(5" f/f Section)
(10" f/f Section)
(12" f/f Section)
(20" f/f Section)
(24" m/f Section)
(36" m/f Section)
(48" m/f Section)
(72" m/f Section)
PXT - 5
PXT - 10
PEXT - 1
PXT - 20
PEXT - 2
PEXT - 3
PEXT - 4
PEXT - 6
(5" f/f Section)
(10" f/f Section)
(12" f/f Section)
(20" f/f Section)
(24" m/f Section)
(36" m/f Section)
(48" m/f Section)
(72" m/f Section)
D - Elbows
MEL-90MM
MEL-90FF
MEL-90FM
MEL-45FM
E - Support Ring
& Plate
MSPXT-8
PSPXT-8
F - Firestop
FS-8
PS-8
G - Roof Flashing
MRF-7
MRF-12
Part No. XG0140 - 092210
PVTK-1
(m/m 90º Elbow)
( f/f 90º Elbow)
( f/m 90º Elbow)
( f/m 45º Elbow)
(1/12 - 7/12 pt.)
(7/12 - 12/12 pt.)
PEL-90MM
PEL-90FF
PEL-90FM
PEL-45FM
PRF-7
PRF-12
„„ Place the springs, supplied with the pipe kit, between the outer
and inner pipes to keep the pipes separate and avoid any
possible hot spots.
„„ Montigo recommends the use of a flex section for the final pipe
connected directly to the fireplace offering greater flexibility of
installation and absorption of movement.
„„ When penetrating a combustible ceiling, a ceiling firestop must
be used.
„„ Montigo recommends that all exterior corners and joints be sealed
with exterior caulking however we encourage you to consult
your Building Envelope Engineer or Waterproofing Consultant
for further recommendations.
IMPORTANT:
Please Refer to your Building Envelope Engineer
or Waterproofing Consultant for a review of ALL
penetrations through exterior walls or the roof.
(m/m 90º Elbow)
( f/f 90º Elbow)
( f/m 90º Elbow)
( f/m 45º Elbow)
(1/12 - 7/12 pt.)
(7/12 - 12/12 pt.)
Page 9
H-Series DL Gas Fireplace
Installation
Section 3-3: INSTALLING A WALL MOUNTED DIRECT VENT
TERMINATION
This section applies to installations where the direct vent termination will be wall mounted.
1). Installation of Termination with built in frame
4). Installation of termination from inside structure
A Termination with a MOSR Frame is installed from the inside of the
structure. These are commonly used in high-rise construction.
Framing, concrete or other
materials
12”
MOSR Frame
A Termination with a Built-In Frame is installed during framing of a structure.
1. Frame the termination opening to 11" x 11".
12”
2. Install exterior sheathing to the structure framing.
3. Fasten the termination to the sheathing using a minimum of 4 screws.
11”
PTO-4 (5"/8")
Termination
Exterior Sheathing, concrete or
other materials
Fastening Hardware,
minimum 4-screws
Framing
Exterior
Sheathing
11”
Fastening Hardware,
minimum 4-screws
Figure 12b. Installing a PTO termination with the MOSR frame.
1. Frame the MOSR opening to 12" x 12".
PTO-4F (5"/8")
Termination
2. Fasten the MOSR frame to the interior side of the studs, concrete,
or finished wall construction using a minimum of 4 screws.
Figure 12. Installing a PTO-F termination.
3. Insert the termination into the MOSR frame as shown here, (from
the inside) and attach to the MOSR by installing a min. quantity of
4 bolts into the threaded nuts on the MOSR Frame.
2). Installation of termination frame at time of framing
5). Installation of a termination shield for Vinyl Siding
Terminations with a MSR frame allow the installation of the frame prior
to installation of the termination.
1. Frame the termination opening to 12" x 12".
2. Secure the MSR Frame to the exterior sheathing of the structure.
3. Fasten the termination to the MSR Frame using a minimum of 4 screws.
12”
Framing
MSR Frame
Fastening Hardware,
minimum 4-screws
Exterior
Sheathing
PTO-4 (5"/8")
Termination
12”
The VSS Termination shield is installed when the exterior of a structure
is clad with Vinyl siding. It is placed directly above, and on-center with
the termination.
VSS Vinyl shield
PTO-4 (5"/8")
Termination
Exterior Vinyl
siding
Figure 12c. Installing the VSS Vinyl Shield.
Installing Heat Guards over Terminations is recommended
Figure 12a. Installing a PTO termination with the MSR frame.
3). Installation of termination frame at time of framing in
Masonry
in installations where the termination is located within 7' feet above
grade, or above a pedestrian walkway, and may be Required by code
in Public areas.
Terminations with a BSR frame allow the installation of the frame in
masonry prior to the installation of the termination
1. Frame the BSR opening to 12" x 12".
2. Secure the BSR Frame to the exterior sheathing of the structure.
12”
Framing
Exterior
Sheathing
12”
BSR Frame
Fastening Hardware,
minimum 4-screws
PTO-4 (5"/8")
Termination
Figure 12c. Installing a PTO termination with the BSR frame.
Page 10
PTKOG (5"/8")
Figure 12d. Installing a PTO termination heat guard.
1. Ensure that the two long mounting brackets are facing the bottom
of the termination. (See inset). This will provide more heat protection
at the top of the termination, where temperatures are highest.
2. Attach to the faceplate of the termination using four sheet metal
screws.
Part No. XG0140 - 092210
H-Series DL Gas Fireplace
Installation
Section 3-3-1: VENTING LAYOUT: Wall mounted termination.
Selection of components and details of venting layout should
adhere to the following guidelines:
„„ Vent terminations must not be recessed in walls or siding.
A
If your installation does not fall
within the venting graph parameters, please contact Montigo
for Power Venting options.
„„ All through-the–wall terminations within 3’ of the fireplace must
have a Montigo Heat Shield (RHS101) installed. See Section
3-3-3.
Acceptable vent run
within non-shaded area.
C
B
„„ All through-the-wall terminations beyond 3' of the fireplace must
have a Montigo Heat Shield (RHS8) installed. See Section 3-3-3.
41”
72”
Unacceptable vent run
within shaded area.
„„ Once the proposed venting layout has been determined, refer to
Figure 13, 14 or 15 to ensure the layout is acceptable.
Notes Wall Mounted Terminations: Top Vent
„„ All measurements for vertical or horizontal runs are measured
from center of the vent pipe.
Figure 13 H34DL* Top Vent Venting Graph for wall mounted
terminations, See Figures 15a & 15b.
„„ Venting runs must fall within the limits set by the venting graphs,
Figure 13, 14 & 15.
The Venting Graph: H38DL*
Measure the vertical height from the fireplace hearth to the centre of the
termination and the horizontal run from the fireplace flue collar to the wall
flange of the termination. Plot on the Venting Graph Figure 14 with an 'X'.
Wall mounted Terminations
The following details are some possible configurations for Wall
mounted terminations. See below.
The Venting Graph: H34DL*
Measure the vertical height from the fireplace hearth to the centre of the
termination and the horizontal run from the fireplace flue collar to the wall
flange of the termination. Plot on the Venting Graph Figure 13 with an 'X'.
If the 'X' falls on or above the top boundary of the shaded area, the
installation is acceptable.
Example A: (Acceptable Installation)
If the vertical dimension from the hearth is 108" and the horizontal run to
the wall flange of the vent termination is 180", this would be an acceptable installation.
Example B: (Acceptable Installation)
If the vertical dimension from the hearth is 48" and the horizontal run to
the wall flange of the vent termination is 72", this would be an acceptable
installation.
Example C: (Unacceptable Installation)
If the vertical dimension from the floor of the fireplace is 60" and the horizontal run to the wall flange of the vent termination is 144", this would
not be an acceptable installation.
If the 'X' falls on or above the top boundary of the shaded area, the
installation is acceptable.
Example A: (Acceptable Installation)
If the vertical dimension from the hearth is 84" and the horizontal run to
the wall flange of the vent termination is 36", this would be an acceptable
installation.
Example B: (Acceptable Installation)
If the vertical dimension from the hearth is 108" and the horizontal run to
the wall flange of the vent termination is 144", this would be an acceptable
installation.
Example C: (Unacceptable Installation)
If the vertical dimension from the floor of the fireplace is 72" and the
horizontal run to the wall flange of the vent termination is 108", this would
not be an acceptable installation.
Acceptable vent run
within non-shaded area.
B
C
A
44”
34”
Unacceptable vent run
within shaded area.
If your installation does not fall
within the venting graph parameters, please contact Montigo
for Power Venting options.
Figure 14 H38DL* Top Vent Venting Graph for wall mounted
terminations, See Figures 15a & 15b.
Part No. XG0140 - 092210
Page 11
H-Series DL Gas Fireplace
Installation
The Venting Graph: H42DL*
Measure the vertical height from the fireplace hearth to the centre of the
termination and the horizontal run from the fireplace flue collar to the wall
flange of the termination. Plot on the Venting Graph Figure 15 with an 'X'.
If the 'X' falls on or above the top boundary of the shaded area, the
installation is acceptable.
72"Max. H34DL*
34"Max. H38DL*
18"Max. H42DL*
Flex section
shown
Example A: (Acceptable Installation)
Termination
If the vertical dimension from the hearth is 84" and the horizontal run to
the wall flange of the vent termination is 36", this would be an acceptable
installation.
41"Min. H34DL*
44"Min. H38DL*
48"Min. H42DL*
Example B: (Acceptable Installation)
If the vertical dimension from the hearth is 120" and the horizontal run to
the wall flange of the vent termination is 132", this would be an acceptable
installation.
Example C: (Unacceptable Installation)
If the vertical dimension from the floor of the fireplace is 72" and the
horizontal run to the wall flange of the vent termination is 108", this would
not be an acceptable installation.
B
Acceptable vent run
within non-shaded area.
Exterior
Wall
Hearth
Figure 15a. Top Vented, wall mounted installation with1 elbow (1 one
90° bend). The vent run must comply with Venting Graph for
Top vent, wall mounted terminations, Figure 13, 14 & 15.
15’foot Max.
30”min
Solid Section
48”
Unacceptable vent run
within shaded area.
If your installation does not fall
within the venting graph parameters, please contact Montigo
for Power Venting options.
Figure 15 H42DL* Top Vent Venting Graph for wall mounted
terminations, See Figures 15a & 15b.
Page 12
RHS8 Heat
Shield
C
A
18”
RHS8 Heat
Shield
Termination
8’foot
Max.
Flex Section
Hearth
Exterior
Wall
Figure 15b. Top Vented, wall mounted Multi-elbow installation. See
Venting Graph for Top vent, wall mounted terminations,
Figure 13, 14 & 15.
Part No. XG0140 - 092210
H-Series DL Gas Fireplace
Installation
Notes Wall Mounted Terminations: Rear Vent
„„ All dimension lengths for vertical or horizontal runs are measured
from center of the vent pipe.
„„ Venting runs must fall within the limits set by the venting graphs,
see Figure 16, 17 & 18.
„„ Fireplace must be converted to Rear Vent configuration prior to
running vent, see Figure 7 and 8.
The Venting Graph H34DL*
Measure the vertical height from the fireplace hearth to the centre of the
termination and the horizontal run from the fireplace flue collar to the wall
flange of the termination. Plot on the Venting Graph Figure 16 with an 'X'.
The Venting Graph: H38DL*
Measure the vertical height from the fireplace hearth to the centre of the
termination and the horizontal run from the fireplace flue collar to the wall
flange of the termination. Plot on the Venting Graph Figure 17 with an 'X'.
If the 'X' falls on or above the top boundary of the shaded area, the
installation is acceptable.
Example A: (Acceptable Installation)
If the vertical dimension from the hearth is 84" and the horizontal run to
the wall flange of the vent termination is 36", this would be an acceptable
installation.
Example B: (Acceptable Installation)
If the vertical dimension from the hearth is 108" and the horizontal run to
the wall flange of the vent termination is 144", this would be an acceptable
installation.
If the 'X' falls on or above the top boundary of the shaded area, the
installation is acceptable.
Example A: (Acceptable Installation)
Example C: (Unacceptable Installation)
If the vertical dimension from the hearth is 60" and the horizontal
run to the wall flange of the vent termination is 24", this would be
an acceptable installation.
If the vertical dimension from the floor of the fireplace is 72" and the
horizontal run to the wall flange of the vent termination is 108", this would
not be an acceptable installation.
Example B: (Acceptable Installation)
Example C: (Unacceptable Installation)
If the vertical dimension from the floor of the fireplace is 60" and
the horizontal run to the wall flange of the vent termination is 120",
this would not be an acceptable installation.
Acceptable vent run
within non-shaded area.
C
Vertical Height (in.)
If the vertical dimension from the hearth is 78" and the horizontal
run to the wall flange of the vent termination is 60", this would be
an acceptable installation.
B
A
34”
Acceptable vent run
within non-shaded area.
27 3/4”
18”
Vertical Height (in.)
C
Unacceptable vent run
within shaded area.
50”
If your installation does not fall
within the venting graph parameters, please contact Montigo
for Power Venting options.
B
Horizontal Run (in.)
A
Acceptable Vent run
within non-shaded area.
46”
34”
25”
18”
Figure 17 H38DL* Rear Vent Venting Graph for wall mounted
terminations, See Figures 18a & 18b.
If your installation does not fall within
the venting graph parameters, (nonShaded area) please contact Montigo
for Power Venting options.
Horizontal Run (in.)
Figure 16. H34DL* Rear Vent Venting Graph for wall mounted
terminations, See Figures 18a & 18b.
Part No. XG0140 - 092210
Page 13
H-Series DL Gas Fireplace
Installation
The Venting Graph: H42DL*
Measure the vertical height from the fireplace hearth to the centre of the
termination and the horizontal run from the fireplace flue collar to the wall
flange of the termination. Plot on the Venting Graph Figure 18 with an 'X'.
NOTE:
18” MAX. horizontal
run with no vertical lift.
If the 'X' falls on or above the top boundary of the shaded area, the
installation is acceptable.
MXT Extension
RHS100 Heat
Shield
Example A: (Acceptable Installation)
If the vertical dimension from the hearth is 84" and the horizontal run to
the wall flange of the vent termination is 36", this would be an acceptable
installation.
Termination
18” MAX.
Example B: (Acceptable Installation)
If the vertical dimension from the hearth is 108" and the horizontal run to
the wall flange of the vent termination is 144", this would be an acceptable
installation.
Example C: (Unacceptable Installation)
If the vertical dimension from the floor of the fireplace is 72" and the
horizontal run to the wall flange of the vent termination is 108", this would
not be an acceptable installation.
Acceptable vent run
within non-shaded area.
Figure 18a. Straight run, Rear Vented, wall mounted termination for
H*DL* models, Figure 16, 17 & 18.
16" Max. H*DL*
Flex or Rigid
Section
C
Vertical Height (in.)
Exterior
Wall
Hearth
25" H34DL*
27 3/4” H38DL*
31 1/2” H42DL*
B
A
Unacceptable vent run
within shaded area.
50”
34”
31 1/2”
18”
If your installation does not fall
within the venting graph parameters, please contact Montigo
for Power Venting options.
Horizontal Run (in.)
Figure 18 H*42DL* Rear Vent Venting Graph for wall mounted
terminations, See Figures 18a & 18b.
Page 14
18”
Max.
25" H34DL*
27 3/4” H38DL*
31 1/2” H42DL*
46"Min.
. H34DL*
46"Min. H38DL*
50"Min. H42DL*
Figure 18b.Rear Vented, wall mounted Multi-elbow termination
installation. Installation for H34DL* & H38DL* must have
a minimum vertical rise of 46".The Installation for H42DL*
must have a minimum vertical rise of 50".
The vent run must comply with the Venting Graph for Rear
vent, wall mounted terminations, Figures 16, 17 & 18.
Part No. XG0140 - 092210
H-Series DL Gas Fireplace
Installation
45° Corner Installation.
Attach an MEL-45 / PEL-45 (45° elbow) directly onto the flue collar.
Cut the MXT-20 / PXT-20 to suit, and attach it to the MEL-45 / PEL45. Slide the fireplace into position and attach to the termination.
Rigid Section
Rigid Elbow
Figure 18c. Corner installation.
45° or less Corner Installation.
Use an MTO-4 / PTO-4 termination and an MFL-1 / PFL-1 or MFL-2
/ PFL-2 (12" or 24" compressed length) and a frame, if appropriate.
Flex may be turned to obtain desired degree of angle required but
must not exceed 45°.
Flex Section
Figure 18d. Flex installation. (NG Models Only)
Note: Through the wall venting kits are also available for both
the Straight and the Corner Installation. The Kit includes a heat
shield, a MFL-12 (f/f) / PFL-12 (f/f) flexible pipe, and a termination
with or without a mounting frame.
Part No. XG0140 - 092210
Page 15
H-Series DL Gas Fireplace
Installation
Section 3-3-2: VENTING COMPONENTS
The following components and associated Montigo part numbers are available for installation of a Wall Mounted Termination.
Use only Montigo Vent Components. Use of non-Montigo parts
will void the warranty and may impede operation of the fireplace.
4" / 7" Venting
5" / 8" Venting
A - Termination
MTO-4
MTO-4F
(3" Length)
(3" Length)
PTO-4
PTO-4F
(3" Length)
(3" Length)
B - Frame Kits
MSR
MOSR
BSR-4
BSR-6
(Stucco Frame)
(Stucco Frame)
(4" Brick Frame)
(6" Brick Frame)
MSR
MOSR
BSR-4
BSR-6
(Stucco Frame)
(Stucco Frame)
(4" Brick Frame)
(6" Brick Frame)
C - Flex Sections
MFL - 1
MFL - 18
MFL - 2
MFL - 3
MFL - 4
MFL - 6
(12" f/f Section)
(18" f/f Section)
(24" f/f Section)
(36" f/f Section)
(48" f/f Section)
(72" f/f Section)
PFL - 1
PFL - 18
PFL - 2
PFL - 3
PFL - 4
PFL - 6
(12" f/f Section)
(18" f/f Section)
(24" f/f Section)
(36" f/f Section)
(48" f/f Section)
(72" f/f Section)
D - Rigid Sections
MXT - 5
MXT - 10
MEXT - 1
MXT - 20
MEXT - 2
MEXT - 3
MEXT - 4
MEXT - 6
(5" f/f Section)
(10" f/f Section)
(12" f/f Section)
(20" f/f Section)
(24" m/f Section)
(36" m/f Section)
(48" m/f Section)
(72" m/f Section)
PXT - 5
PXT - 10
PEXT - 1
PXT - 20
PEXT - 2
PEXT - 3
PEXT - 4
PEXT - 6
(5" f/f Section)
(10" f/f Section)
(12" f/f Section)
(20" f/f Section)
(24" m/f Section)
(36" m/f Section)
(48" m/f Section)
(72" m/f Section)
E - Elbows
MEL-90MM
MEL-90FF
MEL-90FM
MEL-45FM
(m/m 90º Elbow)
( f/f 90º Elbow)
( f/m 90º Elbow)
( f/m 45º Elbow)
PEL-90MM
PEL-90FF
PEL-90FM
PEL-45FM
„„ When penetrating a combustible ceiling, a ceiling firestop
must be used.
„„ Montigo recommends that all exterior corners and joints be
sealed with exterior caulking however we encourage you to
consult your Building Envelope Engineer or Waterproofing
Consultant for further recommendations.
IMPORTANT:
Please Refer to your Building Envelope Engineer
or Waterproofing Consultant for a review of ALL
penetrations through exterior walls or the roof.
(m/m 90º Elbow)
( f/f 90º Elbow)
( f/m 90º Elbow)
( f/m 45º Elbow)
Connection and installation of the vent components should
adhere to the following guidelines:
„„ Use any combination of rigid and Flex pipe as required.
„„ Flex sections may be stretched up to 50% of their total length
(e.g. a 24” section maybe stretched to 36”).
„„ Connect all vent sections using a minimum of three sheet metal
screws on the outer pipe flue..
„„ Ensure the pipe ends male to female slide in a minimum of 1
1/2” of overlap.
„„ Ensure all runs are supported with a minimum of 3 supports
per 10’ of venting.
„„ When hanging/ supporting venting, ensure that 1” clearance
is maintained on sides and bottom of vent runs and 2” above
horizontal vent runs to any combustible material.
„„ Ensure when cutting sections of rigid pipe to maintain integrity
of internal supports.
„„ Place the springs, supplied with the pipe kit, between the outer
and inner pipes to keep the pipes separate and avoid any
possible hot spots.
„„ Montigo recommends the use of a flex section for the final pipe
connected directly to the fireplace offering greater flexibility of
installation and absorption of movement.
Page 16
Part No. XG0140 - 092210
H-Series DL Gas Fireplace
Installation
Section 3-3-3: Heat Shields
Installing a Wall Mounted RHS101 Heat shield.
Installing a Wall Mounted RHS8 Heat shield
The RHS101 Heat shield MUST be used where the RHS8 Termination
(Figure 19 and 19a) CANNOT be used. Use the RHS100 where any
of the dimensions are within the parameters shown, figure 19a.
The RHS8 Heat shield CANNOT be used when the Termination is WITHIN
(36" Min. horizontal and 39" Min. vertical) from the fireplace, or directly
off the rear of the fireplace, as shown figure 19a. The RHS101 Heat
Shield (Figure 19c and 19d) MUST be used within the noted dimensions.
To install the RHS8, frame an opening in combustible construction,
Figure 19 below. Slide the Heat shield in place over the vent pipe
which attaches to the fireplace. After the fireplace and vent pipe has
been installed, clearances should match the dimensions in Figure 19.
1” Min. Both sides Typical
2” Min.
To install the RHS100, Slide the Inner Section over the vent pipe that will
connect to the fireplace. Fasten the vent pipe to the back of the fireplace
with a Min. of three sheet metal screws.
(Note: ensure you DO NOT EXCEED the Max. 18" fireplace clearance).
Next, slide the RHS100 outer section from the outside of the structure,
see Figure 19c.
To complete the installation fasten the Heat Shield Outer Section &
Termination frame to the structure Figure 19d.
RHS100 Heat Shield
Outer Section
RHS8 Heat Shield
Termination
Drywall / sheetrock
RHS100 Heat Shield, inner Section
Vent pipe, from fireplace
Combustible Framing
1” Min.
Fireplace
Figure 19. RHS8 Installation. (Install by sliding over vent pipe where it
passes through the combustible contruction).
36” Min
RHS8 Heat
Shield
PTO Termination
Termination
MTO
18” max
Combustible
framing
Figure 19c. RHS101 Installation. (Install by sliding Outer Section over vent
pipe where it passes through the combustible construction.
RHS100 Heat Shield
Outer Section
Drywall / sheetrock
RHS100 Heat Shield, inner Section
Termination
Flex 39” Min.
Rigid 43” Min.
Fireplace
Figure 19a. RHS8 Installation. (Minimum requirements).
Figure 19d.Heat Shield. After sliding the outer section in place.
Part No. XG0140 - 092210
Page 17
H-Series DL Gas Fireplace
Installation
Section 4: Wiring
Honeywell (Q3450)
Pilot Assembly
Pilot Electrical
Harness Connector
Honeywell Gas
Control (SV9501M)
Models
H34DLNE
H38DLLE
H34DLLE
H42DLNE
H38DLNE
H42DLLE
Gas Control
Connector
Fan Plug
Receptacle
Junction Box
Black
White
Green
115VAC
24VAC
Gnd Screw
40 VA
Transformer
Wall Switch
Figure 20. Wiring with Honeywell gas control and pilot.
Models
H34DLNI
H38DLLI
H34DLLI
H42DLNI
H38DLNI
H42DLLI
Installations in the USA which employ the fans must be grounded in
accordance with local codes or, in the absence of local codes, with the
National Electrical Code, ANSI/NFPA 70-1987.
For more information see the Fan Kit Installation Guide included with
the fan kit.
NOTE:
If any of the original wire supplied with the appliance is replaced, it
must be replaced with the same type, or its equivalent.
5/1/60 Supply
G L1 L2
L2-WH
G L1-BLK
Figure 21. Wiring for the SIT IPI Wiring Schematic
Wiring for the optional Fan Kit
All H*DL* fireplaces may be equipped with optional fan kits for circulating
heat into the living space.
Installations in Canada which employ the fans must be electrically
grounded in accordance with CSA C22.1 Canadian Electrical Code
Part 1 and/or Local Codes.
Page 18
Quick Connect
plug to motor
Figure 21a. Wiring schematic for optional fans.
Part No. XG0140 - 092210
H-Series DL Gas Fireplace
Installation
Section 5: Installing the Gas line
Section 5-1: FUEL CONVERSION
Gasline Acces
0.875 dia.
„„ Verify that your fireplace is compatible with your available gas
type. (Natural Gas or Propane shown by "N" or "L" in your
model number
„„ If gas type is not compatible, contact your local Montigo
representative to purchase a conversion kit.
2
„„ Conversion kits must be installed by a qualified service technician.
7
to center
Section 5-2: GAS PRESSURE
Figure 22. Gas line access.
„„ Optimum appliance performance requires proper input pressures.
„„ Gas line sizing requirements will be determined in ANSI Z221.3
National Fuel Gas Code in the USA and CAN/CGA B149 in
Canada.
„„ Pressure requirements are:
Gas Pressure
Natural Gas
Propane
Minimum inlet pressure
5.5in. w.c.
11in. w.c.
Manifold pressure
3.5in. w.c.
10in. w.c.
„„ The manifold outlet pressure is set from the factory to the
appropriate pressure but should be verified.
„„ To check pressures, control valves have a provision to remove
a 1/8” N.PT. plug to be fitted with a hose barb.
„„ Montigo requires a service shut off valve be located in an
accessible location to isolate the gas supply.
„„ Only install gas shut-off valves approved for use by the state,
province, or other governing body in which the fireplace is being
installed.
Note:
After gas line is connected, each appliance connection,
valve and valve train must be checked while under normal
operating pressure with either a liquid solution, or leak
detection device, to locate any source of leak. Tighten any
areas where bubbling appears or leak is detected until
bubbling stops completely or leak is no longer detected.
DO NOT use a flame of any kind to test for leaks.
WARNING!
When pressure testing the fireplace, Gas line, and input system
follow the appropriate local codes or your area. DO NOT
connect the fireplace to pressures in excess of 1/2lb. This will
damage the gas control valve.
Section 5-3: GAS CONNECTION
„„ See Figure 22 below for location of gas line access.
„„ Flexible gas connectors must not exceed 3 feet in length, unless
allowable within local regulations.
„„ Connect incoming gas line to the 1/2"or 3/8" gas inlet port.
„„ Purge all air out of gas line.
„„ Check appliance connection, valve and valve train under normal
operating pressure with a commercially available leak check
solution.
„„ DO NOT USE A FLAME OF ANY KIND TO TEST FOR LEAKS.
Part No. XG0140 - 092210
Page 19
H-Series DL Gas Fireplace
Section 6: Finishing
Installation
Finishing Around the Fireplace
Combustible mantels and mouldings may be safely installed over the
top and on the front of the fireplace provided that they do not project
beyond shaded area shown in Figure 24.
Fireplace Facing
When sizing the finish material for your fireplace, it is important to remember the following: THE OPENING MUST NOT BE OBSTRUCTED IN ANY
WAY - to do so restricts the air supply for the control compartments
and heat exchanger it also prevents access for servicing controls.
The face of the fireplace may be painted to match the room decor,
provided you use a heat-resistant paint. Decorative facing must not
extend past the fireplace opening at all, because it will interfere with
the access to retainers for removal of glass door.
Vertical Run (in)
Combustible
Construction allowed
in shaded area
Combustible Facing
Material
Combustible Framing
Material
Top of fireplace
WARNING!
We recommend careful consideration be given to the effects of
elevated mantel temperatures which may be in excess of product
design, for example: candles, plastic or pictures. This can cause
melting, deformation, discoloration or premature failure of T.V.
radio, and other electronic components.
Horizontal Run (in)
Figure 24. Combustible mantels and facings.
WARNING!
When covering the upper metal portion of the fireplace, up to 4"
(as shown, Fig.24) with a non-combustible material Please Note:
The decorative facing materials may be subject to temperatures
in excess of 250° F. This should be considered when selecting
facing materials.
WARNING!
Do not attempt to clean glass when hot.
Do not clean glass with abrasive materials as any glass etching may cause premature glass failure.
CAUTION!
DO NOT OPERATE THIS FIREPLACE WITHOUT THE GLASS
DOOR OR WITH A BROKEN GLASS DOOR.
Page 20
Part No. XG0140 - 092210
H-Series DL Gas Fireplace
Installation
Section 7: Installing & Removing the Door
Removing the door:
The H*DL* Series door is removed in a few simple steps. Follow these
below to remove the Horizontal access panel, unlatch the door buckles
and, remove the door. Replace in reverse order.
Remove the Horizontal Access Panel:
Step 1:
Remove the Horizontal Access Panel:
Remove the Horizontal cover
by placing fingers in both finger
holes, then pushing away from
you and lifting out. Place it
Finger Holes
aside during maintenance or
cleaning.
Installed Gas
Install in reverse order.
Valve Cover
Figure 26. Removing and installing the the Horizontal Acess Panel
Step 2:
Locate the Door Buckles:
Step 5:
Ensure the tool is firmly
in the lower end of the
slot, (as shown), Then pull
toward you (Caution: hold
the tool securely).
2
Figure 26d.
Step 6:
Pull hard if necessary to
release the spring tension. (Caution: The latch
springs back with force,
hold the tool securely).
3
Figure 26e.
Step 7:
Remove the tool from
the latch slot. Ensure the
latches are hanging freely,
the hook end is released
from the bottom of the door.
(Repeat all 4-steps for the
remaining latches).
4
Figure 26f.
Figure 26a. Locate the door buckles. (Both Sides Typical)
Step 3:
Release the Door Buckles
Hand-hold
Step 8:
Removing the Door:
Grasp the Door on either side, usually midway and lift upward, lift
the door carefully up and away from the front of the fireplace. See
Figures 26g. Place the Door aside in a safe place while maintenance
and / or cleaning is being performed.
Door Latch Slot
Door Latch Hook
Figure 26b. Door buckle Tool
Step 4:
Firmly grasp hand-hold
end of Door buckle tool
and place the machined
end in the slot under door
frame. (as shown)
1
Figure 26g. Removing and installing the glass doors. (Both Sides
Typical)
Installing the Door:
To install the door, hook the top edge of the door frame into place. Lower
the door into position and follow the previous steps shown in reverse order.
Figure 26c.
Part No. XG0140 - 092210
Page 21
H-Series DL Gas Fireplace
Installation
Section 8: Installing the Accessories
Log 'D'
Installing the Logs:
The H34DL* is supplied with five ceramic fibre logs. Unpack the logs
and handle them very carefully.
Top Left Log
1. Remove the glass door as described on Page 21.
Notch
Fireplace Base
Air Inlets
Pilot Assembly
Figure 29d. Top Left log placement.
5. Place the top right log as shown in figure 29e. A notch is provided on the front right log, and a impression in the Rear bottom
log.
Fireplace Base
Top Right Log
Figure 29a. H34DL*'s Fireplace Base.
2. Install Bottom Rear log as shown in Figure 29b.
Rear / Bottom Log
Log stand
Fireplace Base
Embers
Embers
Notch in Log
Embers
Log stand
Figure 29e. Top right log placement.
Figure 29b. Bottom/Rear log placement.
3. Install Both front base logs, (Figure 29c) on the log stands provided.
See Figure 29b.
6. Start the fireplace. If the flame appears satisfactory, replace the
glass door. If the flame does not appear satisfactory, doublecheck the air inlet and exhaust outlet pipe to ensure that they are
unobstructed.
Notch
Notch
Front Right
Base Log
Front Left
Base Log
Fireplace Base
Figure 29c. Front base logs placement.
4. Place the top left log as shown in figure 29d. A flat area is
provided on the front left log, and a notch in the Rear bottom log,
as shown in figure 29c.
Page 22
CAUTION!
If logs are not placed properly, excessive sooting will result.
The surface of the logs will crack due to the heat from the
flames. This is a normal occurance.
Part No. XG0140 - 092210
H-Series DL Gas Fireplace
Installation
Installing the Logs:
The H38DL* and H42DL* is supplied with a seven ceramic fibre log
logset. Unpack the logs and handle them very carefully.
Step 1.Remove the glass door as described on Page 21.
Top
Right Log
Top
Left Log
Align Pins
Align Pins
Rear / Bottom Log
Top Left
Log
Pilot Assembly
Notch in Log
Top Right
Log
Notch in Log
Fireplace Base
Figure 30a. Placing Bottom Rear Log.
Figure 30d. Placing Top Right and Left Logs.
Step 2.Place the bottom Rear log as shown in figure 30a.
Step 4.Place the bottom Right log as shown in figure 30c
Step 5.Place the Top Right and Left logs using the (4) four alignment
pins protruding from the top of the Right and Left Bottom Logs,
as shown in figure 30d. With these pins align the Top Right and
Left logs using the predetermined alignment holes cast into the
underside of the logs, as shown above, figure 30d insets.
Align
Step 6.Place the Centre Front log , Figure 30e below, as shown using
the notch cast in the Bottom Rear log as shown in figure 30d
above.
Air Inlets
Bottom Left Log
Figure 30b. Placing Bottom Left Log.
Step 3.Place the bottom Left log as shown in figure 30b.
Center Front Log
Align
Centerline of Fireplace
Figure 30e. Placing Centre Front Log.
Step 7.Place the Front Centre log as shown in figure 30e.
Bottom Right Log
Right Front
Log
Groove
in Log
Figure 30c. Placing Bottom Right Log.
Rest Log
Figure 30f. Placing Right Front Log.
Part No. XG0140 - 092210
Page 23
H-Series DL Gas Fireplace
Installation
Installing the Horizontal Louvres:
Place Embers in this area
Figure 30g. Placing Embers.
1. Ensure the fireplace is turned off before beginning installation.
2. Install the upper louvre assembly as shown in figure 31a. Before
tightening the screws fully, adjust the louvre assembly so that it is
centred horizontally and vertically.
Step 9.Place the Embers as shown in figure 30g.
Arrange the ember chips on top of the burner tray. Care should be taken
when placing the embers, as blocked burner ports may cause an
incorrect flame pattern, carbon deposits and delayed ignition. Also,
the embers must never be placed in a way that obstructs any of
the air inlet ports, located at the rear of the burner, as shown in
figure 30b.
Figure 31a.
Installing the upper louvre assembly
3. Install the lower louvre assembly. Line up the slots on each side of
the bottom louvre with the hinge tabs at the base of the fireplace
as shown in figure 31b.
Figure 31b.
Page 24
Installing the lower louvre assembly
Part No. XG0140 - 092210
H-Series DL Gas Fireplace
Operation
Installation
Section 9: Start-up Sequence
with Continuous Pilot
Models
H38DLL
H34DLN
H34DLM
H42DLN
H34DLL
H38DLN
H42DLL
For Your
Safety
- READ
BEFORE
LIGHTING:
with
American
Flame Electronic
Ignition
WARNING!
If you do not follow these instructions exactly, a fire or explosion may
result causing property damage, personal injury or loss of life.
A. This appliance has a pilot which must be lighted by hand.
When lighting the pilot, follow these instructions exactly.
B. BEFORE LIGHTING smell all around the appliance area for
gas. Be sure to smell next to the floor because some gas is
heavier than air and will settle on the floor.
What To Do If You Smell Gas:
QQ Do not try to light any appliance.
QQ Do not touch any electrical switch; do not use any phone
in your building.
QQ Immediately call your gas supplier from a neighbour's
phone. Follow the gas supplier's instructions.
QQ If you cannot reach your gas supplier, call the Fire
Department.
C. Use only your hand to push in or turn the gas control knob.
Never use tools. If the knob will not push in or turn by hand,
don't try to repair it, call a qualified service technician. Force
or attempt to repair may result in a fire or explosion.
D. Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect the
appliance and to replace any part of the control system, and
any gas control which has been under water.
Lighting Instructions:
1.
2.
3.
4.
STOP! Read the safety information above on this label.
Lift out the lower Horizontal access panel.
to "OFF."
Push in gas control knob and turn clockwise
Wait five (5) minutes to clear out any gas. Smell for gas,
including near the floor. If you then smell gas, STOP! Follow
"B" in the safety information above on this label. If you don't
smell gas, go to the next step.
5. Locate pilot burner (See illustration at right.) and follow steps
below.
to "PILOT."
6. Turn knob on gas control counter clockwise
7. Push in gas control knob completely and hold. Light with Piezo
Igniter button. Continue to hold the control knob in for about
(1) minute after the pilot is lit. Release the knob and it will pop
back up. Pilot should remain lit. If it goes out repeat steps 3
through 8.
QQ If knob does not pop up when released. Stop and
immediately call your service technician or gas supplier.
QQ If the pilot will not stay lit after several tries, turn the gas
control knob to "OFF" and call your service technician
or gas supplier.
to
8. Push in gas control knob and turn counter-clockwise
"ON."
9. Replace the lower Horizontal access
panel.
10. Turn on remote switch to ignite fire.
NOTE: Gas control knob cannot be turned from "PILOT" to "OFF"
unless knob is pushed in slightly. Do not force.
To Turn Off Gas To Appliance:
1. Turn off remote switch.
2. Lift out the lower Horizontal access panel.
3. Push in gas control knob slightly and turn
"Off". Do not force.
clockwise to
4. Replace the lower Horizontal access panel.
Part No. XG0140 - 092210
Page 25
H-Series DL Gas Fireplace
Operation
Installation
Models
with Honeywell Electronic Ignition
H34DLNE
H38DLNE
H42DLNE
H34DLLE
H38DLLE
H42DLLE
For Your
Safety
- READ
BEFORE
LIGHTING:
with
American
Flame Electronic
Ignition
WARNING!
If you do not follow these instructions exactly, a fire or explosion may
result causing property damage, personal injury or loss of life.
A. This appliance is equipped with an ignition system that
lights the pilot burner automatically. Do not attempt to light
the pilot by hand.
B. BEFORE LIGHTING smell all around the appliance area for
gas. Be sure to smell next to the floor because some gas is
heavier than air and will settle on the floor.
What To Do If You Smell Gas:
QQ Do not try to light any appliance.
QQ Do not touch any electrical switch; do not use any
phone in your building.
QQ Immediately call your gas supplier from a neighbour's
phone. Follow the gas supplier's instructions.
QQ If you cannot reach your gas supplier, call the Fire
Department.
C. Use only your hand to push in or turn the gas control knob.
Never use tools. If the knob will not push in or turn by
hand, don't try to repair it, call a qualified service technician.
Force or attempt to repair may result in a fire or explosion.
D. Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect
the appliance and to replace any part of the control system,
and any gas control which has been under water.
Lighting Instructions:
1. STOP! Read the safety information above on this label.
2. Flip down the lower trims.
8. If the fireplace does not operate, follow the instructions "To
Turn Off Gas To Appliance" and call your service technician
or gas supplier.
3. Turn switch on the gas control to OFF".
4. Wait 5 minutes to clear out any gas. If you smell gas,
STOP! Follow "B" in the safety information above on this
label. If you don't smell gas, go to the next step.
5. Turn switch on the gas control to "ON". NOTE: This unit is
equipped with an ignition system that lights the pilot burner
automatically. Do not attempt to light the pilot by hand.
6. Turn on wall switch.
7. Flip up the lower trim.
Gas
Inlet
Gas Control Switch
Shown in "On" Position
To Turn Off Gas To Appliance:
1. Turn off remote switch.
3. Turn the switch on the gas control to "Off".
2. Flip down the lower trim.
4. Flip up the trim.
Page 26
Part No. XG0140 - 092210
H-Series DL Gas Fireplace
Operation
Installation
Models
Proflame SIT Electronic Ignition
H34DLNI
H38DLNI
H42DLNI
H34DLLI
H38DLLI
H42DLLI
For Your
Safety
- READ
BEFORE
LIGHTING:
with
American
Flame Electronic
Ignition
WARNING!
If you do not follow these instructions exactly, a fire or explosion may
result causing property damage, personal injury or loss of life.
A. This appliance is equipped with an ignition system that lights
the pilot burner automatically. Do not attempt to light the pilot
by hand.
B. BEFORE LIGHTING smell all around the appliance area for
gas. Be sure to smell next to the floor because some gas is
heavier than air and will settle on the floor.
What To Do If You Smell Gas:
 Do not try to light any appliance.
 Do not touch any electrical switch; do not use any phone
in your building.
 Immediately call your gas supplier from a neighbour's
phone. Follow the gas supplier's instructions.
 If you cannot reach your gas supplier, call the Fire
Department.
C. Use only your hand to push in or turn the gas control knob.
Never use tools. If the knob will not push in or turn by
hand, don't try to repair it, call a qualified service technician.
Force or attempt to repair may result in a fire or explosion.
D. Do not use this appliance if any part has been under water.
Immediately call a qualified service technician to inspect
the appliance and to replace any part of the control system,
and any gas control which has been under water.
Lighting Instructions:
1. STOP! Read the safety information above on this label.
2. Remove the lower Horizontal access panel.
3. Turn Incoming gas valve to the ON" position.
4. Wait 5 minutes to clear out any gas. If you smell gas,
STOP! Follow "B" in the safety information above on this
label. If you don't smell gas, go to the next step.
5. Turn wall switch "ON".
two trials, (one minute audible clicking, thirty seconds of
silence, and then another one minute of audible clicking).
7. After completion of the information in the Troubleshooting
section, Repeat step 5.
8. If the system will not function correctly, follow the instructions "To Turn Off Gas To Appliance" and call your service
technician or gas supplier.
6. If the Fireplace does not light, the System will cycle through
EV1 (Pilot
burner)
Pilot Sensor
Lockout Reset Key
Diagnostic Terminal
Igniter
Ground
EV1 (Pilot burner)
EV2 (Main burner)
Power
Gas "In"
EV2 (Main
burner)
Pilot Adjust Screw
Gas "Out"
Incoming Gas
Line, Shut-off
Valve
To fireplace Main
burner
Command (Wall
switch)
To Turn Off Gas To Appliance:
1. Turn off remote switch.
3. Turn the incoming gas control valve to "Off".
2. Remove the lower Horizontal access panel.
4. Replace the lower Horizontal access panel.
Part No. XG0140 - 092210
Page 27
H-Series DL Gas Fireplace
Maintenance
Models
Hi-Lo Burner
Adjustment:
Lighting Instructions
See pages 25 to 27.
(SIT Nova 820).
General
 Have the fireplace and installation inspected yearly. The inspection
must include, but is not limited to, the following:
• A visual check of the entire vent system and termination.
H38DLL
H34DLN
H34DLM
H42DLN
H34DLL
H38DLN
H42DLL
The H*DL* is equipped with an adjustable burner, allowing you to raise
or lower the flames. To adjust the flames, locate the black knob marked
'Hi-Lo', in the centre of the gas control valve (See Figure 32).

To raise the flame height, turn the black knob (located behind
• An inspection of the explosion relief flappers and the door the lower trim) counter-clockwise.
gasketing to ensure a proper seal.

To lower the flame height, turn clockwise.
• An inspection of the burner, venturi, and primary air openings.
• An inspection of the gas valve, gas components, and pilot flame.
For your convenience a 1/8" manifold pressure tap is supplied
on the gas valve for a test gauge connection.
'Hi-Lo' Adjustment Knob
• Ensure proper log placement as per this manual.
• Inspection of all optional equipment; fans, thermostats, etc.
 For Natural Gas this appliance requires a minimum inlet pressure
of 5.5" W.C. and a manifold pressure of 3.5" W.C.
 For Propane Gas this appliance requires a minimum inlet pressure
of 11" W.C. and a manifold pressure of 10" W.C.
 Always keep the fireplace area clear and free of combustible materials,
as well as gasoline and other flammable vapors and liquids.
 Do not use this appliance if any part has been under water. Immediately
call a qualified service technician to inspect the appliance and to
replace any part of the control system and any gas control which
has been under water.
Cleaning
Gas Control Knob
(Shown in “Pilot” position)
Figure 32. 'Hi-Lo' Adjustment on the H*DL* s gas valve,
Pilot Burner Adjustment: (SIT Nova 820).
1. Locate Pilot Adjustment Screw. (See figure 33.)
2. Adjust pilot screw to
provide properly sized
flame as shown.
When the fireplace is first activated, there may be some smoking and
a visible film may be left on the glass. This is a normal condition, and is
the result of burning of protective coatings on new metal.
 Glass must be cleaned periodically to remove any film (which is
a normal by-product of combustion) which may be visible. Film
can easily be removed by removing the door, as shown on Page
19. Handle the door carefully, and clean it with non-abrasive glass
cleaners. One of the most effective products is Kel Kem.
 Silicone seals on inner door during initial firing will "off gas", leaving
a visual deposit of a white substance on combustion chamber walls.
This can easily be removed using normal household products.
3. After installing or servicing, leak test with a soap solution with
main burner on. Coat pipe and tubing joints, gasket etc. with soap
solution. Bubbles indicate leaks. Tighten any areas where the
bubbles appear until the bubbling stops completely.
Power
Generator
Pilot Adjustment Screw
 Use a vacuum cleaner or whisk broom to keep the control
compartment, burner, and firebox free from dust and lint. Wall Switch
 Logs may be cleaned periodically with a vacuum to remove soot or
other contaminates.
CAUTION!
 Fireplace gas control must be in the “OFF” position and pilot
and main burners extinguished when cleaning appliance with
a vacuum.
Inlet Pressure
Manifold Pressure
Test Connection
Figure 33. 'Pilot' Adjustment on the H*DL* s gas valve.
 Doors can get very hot. Handle only when cool.
Page 28
Part No. XG0140 - 092210
H-Series DL Gas Fireplace
Maintenance
Troubleshooting:
Models
(SIT Nova 820).
H38DLL
H34DLN
H34DLM
H42DLN
H34DLL
H38DLN
H42DLL
Troubleshooting:
(Honeywell)
Models
H34DLNE
H38DLNE
H42DLNE
H34DLLE
H38DLLE
H42DLLE
The following is a troubleshooting chart of possible problems:
PROBLEM
CORRECTIVE ACTION
Noisy Pilot Flame
Locate pilot adjustement screw on
gas control valve. Flame is decreased by
turning adjustment screw clockwise.
Pilot won’t ignite Disconnect remote wires and try to
light pilot. If pilot now works, remote
connections are faulty. Check wiring
diagram figure 33.
Main burner will
not light
1. Check wiring (see figure 33).
2. Check wall switch for proper connection.
Troubleshooting:
(SIT - IPI Electronic)
Models
H34DLNI
H38DLNI
H42DLNI
H34DLLI
H38DLLI
H42DLLI
1. Locate the lead to the battery backup, (remove)
(Refer to schematic, below)
2. Locate the AC/DC wall transformer, (Unplug connector)
(Refer to schematic, below)
1.
2.
If your fireplace still does not operate correctly, consult your dealer or
the manufacturer.
All service and repairs should be performed by a qualified
Technician.
All spare parts, optional fans, and optional trim finishes are available
from your local dealer or the manufacturer.
If your fireplace still does not operate correctly, consult your dealer or
the manufacturer.
Part No. XG0140 - 092210
Page 29
H-Series DL Gas Fireplace
Maintenance
Spare Parts List
H34DL
H38DL
H42DL
NG Gas Valve
RGC1006
RGC1006
RGC1006
LP Gas Valve
RGC1005
RGC1005
RGC1005
NG Pilot
RPA020
RPA020
RPA020
LP Pilot
RPA021
RPA021
RPA021
Burner NG
RBH3403
RBH3803
RBH4203
Burner LPG
RBH3404
RBH3804
RBH4204
Orifice NG
ROR1120
ROR1122
ROR1124
Orifice LPG
ROR1121
ROR1123
ROR1125
Door
RDTH34
RDTH38
RDTH42
Log Set
RLGSH34
RLGSH38
RLGSH42
Log Base
RLGSH34B
RLGSH38B
RLGSH42B
Page 30
Part No. XG0140 - 092210
H-Series DL Gas Fireplace
Appendix A - Termination Locations
A = clearance to the termination frame above grade, veranda, porch, deck,
or balcony [16 inches (41 cm) minimum]
N = † clearance above paved sidewalk or a paved driveway located on public
property [*7 feet (2.1 m) minimum]
B = clearance to door, or sides and top of window, that may be opened [16
inches (41 cm) minimum for appliances ≤100 000 BTU/H (30kW)]
P = c l e a r a n c e u n d e r v e r a n d a , p o r c h , d e c k , o r b a l c o n y
[16 inches (41 cm) minimum‡ to non-combustibles]
[22 inches (56 cm) minimum‡ to combustibles]
C = clearance to bottom of window that may be opened horizontally [36 inches
(92 cm) minimum for appliances ≤100 000 BTU/H (30kW)]
Q = clearance above a roof [24 inches (61 cm) minimum]
D = no clearance to permanently closed window when installed with approved
glass penetration termination
R = clearance to adjacent walls and neighboring buildings
[18 inches (46 cm) minimum]
E = clearance to permanently closed window [16 inches 41 cm recommended
to prevent condensation on window]
S = c l e a r a n c e f r o m c o r n e r i n r e c e s s e d l o c a t i o n
[12 inches (31 cm) minimum]
F = vertical clearance to ventilated soffit located above the termination within a
horizontal distance of 2 feet (61 cm) from the centreline of the termination
[22 inches (56 cm) minimum]
T = m a x i m u m d e p t h i n
[48 inches (122 cm) minimum]
G = c l e a r a n c e t o u n v e n t i l a t e d s o f f i t [ 1 6 i n c h e s
(41 cm) minimum to non-combustibles]
[22 inches (56 cm) minimum to combustibles]
H = clearance to outside corner [9 inches (23 cm) minimum]
I = clearance to inside corner [12 inches (31 cm) minimum]
J = * not to be installed above a meter/regulator assembly within
40" (103 cm) horizontally from the centreline of the regulator
K = clearance to service regulator vent outlet [3 feet minimum in the United
States] [*6 feet (1.8 m) minimum in Canada]
recessed
location
U = m i n i m u m w i d t h f o r b a c k w a l l o f r e c e s s e d l o c a t i o n
[24 inches (61 cm) minimum]
V = no horizontal clearance between the frames of two terminations that
are level.
W = horizontal clearance between the frames of two terminations that are
not level. [36 inches (92 cm) minimum]
†
a vent shall not terminate directly above a sidewalk or paved driveway
which is located between two single family dwellings and serves both
dwellings
L = clearance to non-mechanical air supply inlet to building or the combustion
air inlet to any other appliance [16 inches (41 cm) minimum for appliances
≤100 000 BTU/H (30kW)]
M = clearance to mechanical air supply inlet [*6 feet (1.8 m) minimum]
only permitted if veranda, porch, deck, or balcony has an open side that
is equal to or greater than the depth of the enclosed area
*
as specified in CGA B149 Installation Codes. Note: local Codes or
Regulations may require different clearance.
‡
Part No. XG0140 - 092210
Page 31
H-Series DL Gas Fireplace
Appendix B - Warranty
The Warranty
The Companies warrants the Montigo Gas Appliance to be free from defects in materials and workmanship at the time of manufacture. On the Montigo fireplace,
there is a ten-year warranty on the firebox and its components, a five-year warranty on the main burner and pilot burner, and a one-year warranty on the gas control
valve, fibre logs and Power Vent Module. The Glass, plated / painted finishes, and refractory lining are exempt from the warranty.
Remedy And Exclusions
The coverage of this Warranty is limited to all components of the Gas Appliance manufactured by The Companies.
This Warranty only covers Montigo Gas Appliances installed in the United States or Canada.
If the components of the Gas Appliance covered by this Warranty are found to be defective within the time frame stated (see The Companies right of investigation
outlined below). The Companies will, at its option, replace or repair defective components of the Gas Appliance manufactured by The Companies at no charge,
and will also pay for reasonable labour costs incurred in replacing or repairing components. If repair or replacement is not commercially practical, The Companies
will, at its option, refund the purchase price of the Montigo Gas Appliance.
This Warranty covers only parts and labour as provided above. In no case shall The Companies be responsible for materials, components, or construction which
are not manufactured or supplied by The Companies, or for the labour necessary to install, repair or remove such materials, components or construction. All
replacement or repair components will be shipped F.O.B. the nearest The Companies factory.
Qualifications To The Warranty
The Gas Appliance Warranty outlined above is further subject to the following qualifications:
(1) The Gas Appliance must be installed in accordance with The Companies installation instructions and local building codes. The Warranty on this Montigo
Gas Appliance covers only the component parts manufactured by The Companies. The use of components manufactured by others with this Montigo Gas
Appliance could create serious safety hazards, may result in the denial of certification by recognized national safety agencies, and could be in violation of
local building codes. This warranty does not cover any damages occurring from the use of any components not manufactured or supplied by The Companies
(2) The Montigo Gas Appliance must be subjected to normal use. The Gas Appliances are designed to burn gas only. Burning conventional fireplace fuels such
as wood, coal or any other solid fuel will cause damage to the Gas Appliance, will produce excessive temperatures and will result in a fire hazard.
Limitations On Liability
It is expressly agreed and understood that The Companies sole obligation, and purchaser's exclusive remedy under this Warranty, under any other warranty,
expressed or implied, or in contract, tort or otherwise, shall be limited to replacement, repair, or refund, as specified above.
In no event shall The Companies be responsible for any incidental or consequential damages caused by defects in its products, whether such damage occurs
or is discovered before or after replacement or repair, and whether or not such damage is caused by The Companies negligence. Some states do not allow the
exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. The duration of any implied warranty
with respect to this Montigo Gas Appliance is limited to the duration of the foregoing warranty. Some states do not allow limitation on how long an implied warranty
lasts, so the above may not apply to you.
Investigation Of Claims Against Warranty
The Companies reserves the right to investigate any and all claims against this Warranty and to decide upon method of settlement.
The Companies Are Not Responsible For Work Done Without Written Consent
The Companies shall in no event be responsible for any warranty work done without first obtaining The Companies written consent.
Dealers Have No Authority To Alter This Warranty
The Companies employees and dealers have no authority to make any warranties nor to authorize any remedies in addition to or inconsistent with those stated above.
How To Register A Claim Against Warranty
In order for any claim under this Warranty to be valid, The Companies must be notified of the claimed defect in writing or by telephone, as soon as reasonably
possible after the defect is discovered. Claims against this Warranty in writing should include the date of installation, and a description of the defect.
Other Rights
This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
NOTE:
The Companies as stated above refer to - Canadian Heating Products Inc. and/or Montigo Del Ray Corp.
Canadian Heating Products Inc. and/or Montigo DelRay Corp. reserves the right to make changes at any time, without notice, in design, materials,
specifications, prices and also to discontinue colors, styles and products.
Page 32
Part No. XG0140 - 092210
H-Series DL Gas Fireplace
Appendix C - State of Massachusetts
Amendment
(Gas Fireplace / Equipment sold in the State of Massachusetts)
5.08: Modifications to NFPA-54, Chapter 10
(1) Revise NFPA-54 section 10.5.4.2 by adding a second exception as follows:
Existing chimneys shall be permitted to have their use continued when a gas conversion burner is installed, and shall be equipped with a manually reset device
that will automatically shut off the gas to the burner in the event of a sustained back-draft.
(2) Revise 10.8.3 by adding the following additional requirements:
(a) For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for residential purposes,
including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than seven (7) feet above finished grade in
the area of the venting, including but not limited to decks and porches, the following requirements shall be satisfied:
1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time of installation of the side wall horizontal vented gas fueled equipment, the installing plumber or gas fitter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-up is installed on the floor
level where the gas equipment is to be installed. In addition, the installing plumber or gas fitter shall observe that a battery operated or hard wired carbon
monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure served by the side wall horizontal vented gas fueled
equipment. It shall be the responsibility of the property owner to secure the services of qualified licensed professionals for the installation of hard wired carbon
monoxide detectors
a. In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard wired carbon monoxide detector with
alarm and battery back-up may be installed on the next adjacent floor level.
b. In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall have a period of thirty (30) days
to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon monoxide detector with an alarm
shall be installed.
2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon monoxide detector as required in accordance with the above provisions
shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS certified.
3. SIGNAGE. A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight (8) feet
above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The sign shall read, in print
size no less than one-half (1/2) inch in size, “GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.
4. INSPECTION. The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation unless,
upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR 5.08(2)(a)1 through 4.
(b) EXEMPTIONS: The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4:
1. The equipment listed in Chapter 10 entitled “Equipment Not Required To Be Vented” in the most current edition of NFPA 54 as adopted by the
Board; and
2. Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the dwelling, building or structure used in whole or in part for residential purposes. (c) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM PROVIDED. When the manufacturer of Product
Approved side wall horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the instructions
provided by the manufacturer for installation of the equipment and the venting system shall include:
1. Detailed instructions for the installation of the venting system design or the venting system components; and
2. A complete parts list for the venting system design or venting system.
(d) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED. When the manufacturer of a Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the flue gases, but identifies “special venting systems”,
the following requirements shall be satisfied by the manufacturer:
1. The referenced “special venting system” instructions shall be included with the appliance or equipment installation instructions; and
2. The “special venting systems” shall be Product Approved by the Board, and the instructions for that system shall include a parts list and
detailed installation instructions.
(e) A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions, all parts lists for
venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of the installation.
(3) After NFPA-54 section 10.10.4.2 add a new section 10.10.4.3 as follows:
When more than four gas appliances are to be vented through a common gas vent or common horizontal vent manifold, a plan of the proposed vent installation
shall be submitted to the Inspector and the serving gas supplier for review and approval.
Extraction from: Massachusets Rules and Regulations
5.00: Amendments To 2002 Edition Of ANSI Z223.1-NFPA-54
Part No. XG0140 - 092210
Page 33
H-Series DL Gas Fireplace
Appendix D - Mobile Home
This appliance may be installed as an OEM installation
in a manufactured home (USA only) or mobile home and
must be installed in accordance with the manufacturer's
instructions and the Manufactured Home Construction
and Safety Standard, Title 24 CFR, Part 3280, in the
United States or The Mobile Home Standard, CAN / CSA
Z240 MH Series, in Canada. This appliance is only for
use with the type(s) of gas indicated on the rating plate.
A conversion kit is supplied with the appliance.
H*DLM-Mobile Home fireplaces:
The mobile home option is a factory installed on the H34DLM gas fireplaces, and are for use in a manufactured or mobile home.
Note:
The H34DM-E equipped with Hot Surface Ignition (HSI) are not
approved for use in mobile or manufactured homes.
The H34DLM is rated for:
Natural Gas at 18,000 BTU/H (5.28 Kilowatts) max. input, and
16,000 BTU/H (4.69 Kilowatts) min. input.
Propane at 18,000 BTU/H (5.28 Kilowatts) max. input, and
16,000 BTU/H (4.69 Kilowatts) min. input.
Gas Control Valve
The following gas control valve is installed on the H34DLM.
Power
Generator
Pilot Adjustment Screw
Wall Switch
Inlet
Pressure
Manifold Pressure
Test Connection
Figure B1. Sit Nova 820 gas valve.
Conversion Kits
The H34DLM mobile home appliance is field convertible between
Natural Gas (NG) and Propane (LP).
To convert from Natural Gas to Propane order conversion kit
# RCV734.
To convert from Propane to Natural Gas order conversion kit
H34DL* Part No. # RCV834.
Conversion kits are available for standard H34DL-l conversion
between Natural Gas (NG) and Propane (LP).
A manufactured home (USA only) or mobile home OEM
installation must conform with the Manufactured Home
Construction and Safety Standard, Title 24 CFR, Part
3280, or when such a standard is not applicable, the
Standard for Fire Safety Criteria for Manufactured Home
Installation Sites and Communities, ANSI/NFPA 501A, in
the United States or the Mobile Home Standard, CAN /
CSA Z240 MH Series, in Canada.
Page 34
Part No. XG0140 - 092210
H-Series DL Gas Fireplace
Notes
Part No. XG0140 - 092210
Page 35
XG0140 - 092210
Canadian Heating Products Inc.
Langley, BC V4W 4A1
Montigo Del Ray Corp.
Ferndale, WA 98248
Download PDF