Apureleet ja optot IC10 2014, sivut 39
© Siemens AG 2013
Switching Devices – Contactors
and Contactor Assemblies –
Contactor Relays and Relays
5
Price groups
PG 41A, 41B, 41H, 4N1
5/4
5/15
5/16
5/24
5/32
5/35
5/37
Introduction
Contactor relays
SIRIUS 3RH2 contactor relays,
4- and 8-pole
SIRIUS 3RH24 latched contactor relays,
4-pole
3TH4 contactor relays,
8- and 10-pole
3TH2 contactor relays,
4- and 8-pole
Coupling contactors
SIRIUS 3RH21 coupling contactors for
switching auxiliary circuits, 4-pole
Contactors with extended
operating range 0.7 ... 1.25 × Us
for railway applications
SIRIUS 3RH21 contactor relays
3TH4 contactor relays
5/53
Coupling relays
3TX7 coupling relays, narrow design
Relay couplers
Relay couplers with plug-in design
Semiconductor couplers
SIRIUS 3RS18 coupling relays
with industrial enclosure
Relay couplers
Coupling relays with
LZS/LZX plug-in relays
Plug-in relay couplers
Ch.4
Power relays/Miniature contactors
3TG10 contactors, 4-pole, 4 kW
5/39
5/44
5/47
5/51
Notes:
3RH1 contactor relays can be found
- in the Catalog Add-On
IC 10 AO · 2014 in the DVD box IC 01
- in the Catalog Add-On
IC 10 AO · 2014 at the Information
and Download Center
- in the interactive catalog CA 01
- in the Industry Mall
Conversion tool
e.g. from 3RH11 to 3RH21 see
www.siemens.com/sirius/conversion-tool
Siemens
Siemens
IC 10
IC· 10
2014
· 2014
5
5/2
© Siemens AG 2013
Switching Devices — Contactors and Contactor Assemblies
Contactor Relays and Relays
Introduction
■ Overview
The advantages at a glance
Size
Type
S00
3RH21
S00
3RH22
3TH42
3TH43
3TH2
Article No.
Page
3RH21
5/10, 5/11
8-pole
3RH22
5/10, 5/11
4-pole, latched
3RH24
5/15
3RH2 contactor relays
• Screw terminals, spring-type terminals and
ring terminal lug connections
5
4-pole
Coupling contactors
• Coils for control by PLC
3RH21
5/32
Contactor relays
for railway applications
• Coils with extended voltage range
3RH21
5/35
• Screw terminals
3TH42
5/20
3TH43
5/21
• Coils with extended voltage range
3TH42
5/37
4-pole
• Screw terminals, flat connectors and solder pin connections
3TH20
5/28
8-pole
• Screw terminals
3TH22
5/28
4-pole, latched
• Screw terminals
3TH27
5/28
• On front
3RH2911
5/12
• Lateral
3RH2911
Chapter 3
• Delayed, on front
3RA28
Chapter 3
Timing relay blocks
• On front
3RA281.
Chapter 3
Surge suppressors
• On front
3RT2916
5/13
Additional load module
• On front
3RT2916
5/13
3TH4 contactor relays
8-pole
10-pole
Contactor relays for
railway applications
3TH2 contactor relays
Accessories for 3RH2 contactor relays
Auxiliary switch blocks
Note:
Safety characteristics for contactors see Chapter 16,
"Appendix" ➞ "Standards and Approvals" ➞ "Overview".
5/2
Siemens IC 10 · 2014
© Siemens AG 2013
Switching Devices — Contactors and Contactor Assemblies
Contactor Relays and Relays
Introduction
The advantages at a glance
Type
3TX7002
3TX7014
3RS18
LZS/LZX
3TG10
Article No.
Page
• Width 11.5 mm (1 NO), 17.5 mm (1 CO) or
22.5 mm (2 NO, 2 CO)
3TX7002,
3TX7003
5/39
• Width 6.2 mm (1 NO, 1 CO) or
12.5 mm (1 CO)
3TX7004,
3TX7005
Relay couplers
5
Coupling links, narrow design
• Output coupling links
• Input coupling links with hard gold-plating
Plug-in base couplers, complete with relay
• Width 6.2 mm (1 NO, 1 CO)
• Relays, replaceable
3TX7014-1..00;
3TX7015-1..00
5/44
Plug-in base couplers, complete with relay
and hard gold-plating
• Width 6.2 mm (1 CO)
3TX7014-1..02;
3TX7015-1..02
5/44
Semiconductor couplers
• Output 1 semiconductor, triac or transistor,
width 6.2, 11.5 and 12.5 mm
3TX7002,
3TX7004,
3TX7005
5/47
• Protective separation up to 300 V between
contacts and relay circuits
• 1, 2 or 3 changeover contacts
• Hard gold-plated contacts in combination
and wide voltage range versions
3RS18
5/51
Plug-in relay couplers with 2, 3 and 4 changeover
contacts
• Switching capacity 12 A/10 A/6 A
• Width 27 mm
• Base with or without logical separation
LZS/LZX:PT
5/53
Plug-in relay couplers with 3 changeover contacts and
circular base
• Switching capacity 10 A
• 11-pole circular base
• Width 38 mm
LZS/LZX:MT
5/59
Plug-in relay couplers with 1 or 2 changeover contacts
• Switching capacity 16 A/8 A
• Width 15.5 mm
• Base with or without logical separation
LZS/LZX:RT
5/60
• Switching capacity 20 A (AC-1) or
8.4 A (AC-2, AC-3)
• 4-pole, hum-free
• Width 36 mm
3TG10
Ch. 4
Coupling relays in industrial enclosure
Relay couplers
Coupling relays with plug-in relays
Miniature contactors (power relays)
With screw and flat connectors
Connection methods
The contactor relays and the relays are available with screw
terminals (box terminals) or with spring-type terminals.
Screw terminals
Devices of the 3TH2 series are also available for connection with
flat connectors and solder pin connectors.
Spring-type terminals
The plug-in bases for LZS/LZX coupling relays are also available
with plug-in terminals.
Flat connectors
As an option the devices of the 3RH2 series are also available
for connection with ring terminal lugs, particularly versions for
North America and Japan.
Solder pin connections
Plug-in terminals
Ring terminal lug connections
The terminals are indicated in the corresponding
tables by the symbols shown on orange backgrounds.
Siemens IC 10 · 2014
5/3
© Siemens AG 2013
Contactor Relays
SIRIUS 3RH2 contactor relays,
4- and 8-pole
■ Overview
Contactor relays and coupling relays
Size S00 with accessories
10
5
3
1
11
4
11
10
5
2
6
12
7
NSB0_02058
11
8
13
9
1 Contactor relay
2 Coupling relay for auxiliary circuits
3 Solid-state timing relay block
4 1-pole auxiliary switch block, cable entry from the top
5 2-pole auxiliary switch block, cable entry from the top
6 1-pole auxiliary switch block, cable entry from the bottom
7 2-pole auxiliary switch block, cable entry from the bottom
8 4-pole auxiliary switch block
(terminal designations according to EN 50011 or EN 50005)
9 2-pole auxiliary switch block, solid-state compatible version
(terminal designations according to EN 50005)
10 Solder pin adapter for contactor relays with 4-pole auxiliary switch block
11 Solder pin adapter for contactor and coupling relays
12 Additional load module for increasing the permissible residual current
13 Surge suppressor with LED
14 Surge suppressor without LED
5/4
Siemens IC 10 · 2014
14
© Siemens AG 2013
Contactor Relays
SIRIUS 3RH2 contactor relays,
4- and 8-pole
Standards
Auxiliary switch blocks
IEC 60947-1, EN 60947-1,
IEC 60947-4-1, EN 60947-4-1,
IEC 60947-5-1, EN 60947-5-1
The 3RH21 contactor relays can be expanded by up to four contacts by the addition of snap-on auxiliary switch blocks.
The 3RH2 contactor relays have screw, ring terminal lug or
spring-type terminals. The basic unit contains four contacts with
terminal designations according to EN 50011.
The 3RH2 contactor relays are suitable for use in any climate.
They are finger-safe according to EN 50274. The devices with
ring terminal lug connection comply with degree of protection
IP20 when fitted with the related terminal cover.
The auxiliary switch block can easily be snapped onto the front
of the contactor relays. The auxiliary switch block has a centrally
positioned release lever for disassembly.
Auxiliary switches according to EN 50011
Contact reliability
High contact stability at low voltages and currents, suitable for
solid-state circuits with currents  1 mA at a voltage of  17 V.
Surge suppression
RC elements, varistors, diodes or diode assemblies (combination of a diode and a Zener diode) can be plugged onto all 3RH2
contactor relays from the front for damping opening surges in
the coil. The plug-in direction is determined by a coding device.
Note:
The OFF-delay of the NO contact and the ON-delay of the
NC contact are increased if the contactor coils are attenuated
against voltage peaks (noise suppression diode 6 to 10 times;
diode assembly 2 to 6 times, varistor +2 to 5 ms).
In addition, fully mounted 3RH22 8-pole contactor relays are
available; the mounted 4-pole auxiliary switch block is not removable. These versions are built according to special Swiss
regulations SUVA and are distinguished externally by a red
labeling plate.
Auxiliary switches according to EN 50005
All contactor relays with the identification numbers 40E, 31E and
22E can be extended with auxiliary switch blocks to obtain contactor relays with 5 to 8 contacts. The permissible combinations
and the resulting identification numbers can be found in the selection tables in Chapter 3, pages 3/48 to 3/52.
Of the auxiliary contacts (integrated plus mountable) possible
on the device, no more than four NC contacts are permitted.
Accessories
Manuals
The accessories for the 3RT2 contactors in size S00 can also be
used for the 3RH2 contactor relays (see pages 5/13 and 5/14
and also Chapter 3).
For more information, see
• System manual "SIRIUS Innovations – System Overview",
http://support.automation.siemens.com/WW/view/en/60311318
• Manual "SIRIUS Innovations – SIRIUS 3RT2 Contactors/
Contactor Assemblies",
http://support.automation.siemens.com/WW/view/en/60306557
Article No. scheme
Digit of the article No.
1st - 3rd 4th 5th 6th 7th
@@@
SIRIUS contactor relays
@
@
@
@
8th 9th 10th 11th 12th
–
@
@
@
@
@
@
@
@
@
@
@
@
@
@
@
3RH
2nd generation
2
@
Device type (e.g. 1 = 4-pole contactor relay, 2 = 8-pole contactor relay)
@
Number of NO contacts (e.g. 2 = 2 NO)
@
Number of NC contacts (e.g. 2 = 2 NC)
@
Connection type (1 = screw, 2 = spring)
@
Operating range / solenoid coil circuit (e.g. A = AC standard / without)
Rated control supply voltage (e.g. P0 = 230 V, 50 Hz)
@
No significance
Special version
Example
13th 14th 15th 16th
–
3RH
2
1
2
2
–
1
A
P
0
0
Note:
The article No. scheme is presented here merely for information
purposes and for better understanding of the logic behind the
article numbers.
For your orders, please use the article numbers quoted in the
catalog in the Selection and ordering data.
Siemens IC 10 · 2014
5/5
5
The 3RH2911–.GA .. auxiliary switch blocks are available for terminal designations according to EN 50011 or IEC 60947-5-1
(see page 5/12). They are coded, and therefore cannot be combined with contactor relays with identification numbers 31E
or 22E.
© Siemens AG 2013
Contactor Relays
SIRIUS 3RH2 contactor relays,
4- and 8-pole
■ Technical specifications
Contactor relays
Type
3RH2
Size
S00
The contactor relays are designed for operation on a
vertical mounting surface.
360°
22,5° 22,5°
NSB0_00478c
Permissible mounting position
Upright mounting position
NSB0_00477a
Special version required
(3RH2122-2K.40 coupling relays and contactor relays with extended
operating range on request)
3RH22:
Yes, in the basic unit and the auxiliary switch block as well as between
the basic unit and the snap-on auxiliary switch block (permanently
mounted) according to:
• ZH 1/457
• IEC 60947-5-1, Appendix L
Explanations:
There is positively-driven operation if it is ensured that the NC and
NO contacts cannot be closed at the same time.
ZH1/457
Safety Rules for Controls on Power-Operated Metalworking Presses.
IEC 60947-5-1, Appendix L
Low-voltage switchgear and controlgear, Special requirements for positivelydriven contacts
Note:
3RH2911-.NF. solid-state compatible auxiliary switch blocks have no
positively-driven contacts.
Contact reliability
Contact reliability at 17 V, 1 mA acc. to IEC 60947-5-4
Frequency of contact faults <10-8 i.e. < 1 fault per 100 million operating
cycles
Contact endurance for AC-15/AC-14 and
DC-13 utilization categories
The contact endurance is mainly dependent on the breaking current. It is
assumed that the operating mechanisms are switched randomly, i.e. not
synchronized with the phase angle of the supply system.
If magnetic circuits other than the contactor coil systems or solenoid
valves are present, e.g. magnetic brakes, protective measures for the
load circuits are necessary, e.g. in the form of RC elements and freewheel diodes.
The characteristic curves apply to:
•
•
•
•
3RH21/3RH22 contactor relays1)
3RH24 latched contactor relays
3RH2911 auxiliary switch blocks1)
Auxiliary switch blocks for snapping onto the front,
max. 4-pole and for mounting onto the side in size S00
30
NSB0_02061b
Basic unit
Million operating cycles (106)
5
Positively-driven operation of contacts in contactor relays
3RH2:
Yes, in the basic unit and the auxiliary switch block as well as between
the basic unit and the front-mounted auxiliary switch block (removable)
according to:
• ZH 1/457
• IEC 60947-5-1, Appendix L
10
5
4
3
2
1
DC-13
220 V
Basic unit with
attachable
contact block
DC-13
110 V
AC-15/AC-14
Basic unit with
attachable
contact block
0,5
DC-13
24V
0,1
0,05
0,01
0,01
0,03 0,05 0,1
0,3 0,5
1
-DC-13 e -DC-13
220 V
110 V
e
Diagram legend:
a = Breaking current
e = Rated operational current
1)
3RH22, 3RH2911: Ie = 6 A for AC-15/AC-14 and DC-13.
5/6
Siemens IC 10 · 2014
2
3 4 5 6 7 10
e -DC-13
24 V
a
(A)
-AC-15
< 230 V
e
© Siemens AG 2013
Contactor Relays
SIRIUS 3RH2 contactor relays,
4- and 8-pole
3RH21
3RH22
3RH24
Size
S00
S00
S00
mm
45 x 57.5 x 73
--
90 x 57.5 x 73
mm
45 x 57.5 x 116
45 x 57.5 x 116
--
H
Type
• With mounted auxiliary switch block
W
D
Dimensions (W x H x D) with screw terminals
General technical specifications
Mechanical endurance
• Basic units
Operating cycles 30 million
5 million
• Basic unit with snap-on auxiliary switch block
Operating cycles 10 million
5 million
• Solid-state compatible auxiliary switch block
Operating cycles 5 million
Rated insulation voltage Ui (pollution degree 3)
V
690
Rated impulse withstand voltage Uimp
kV
6
Protective separation between the coil and the contacts in the basic unit
acc. to IEC 60947-1, Appendix N
V
400
°C
°C
-25 ... +60
-55 ... +80
5
Permissible ambient temperature
• During operation
• During storage
Degree of protection acc. to IEC 60947-1, Appendix C
IP20
Touch protection acc. to EN 50274
Finger-safe
Shock resistance
• Rectangular pulse
- AC operation
- DC operation
g/ms
g/ms
7.3/5 and 4.7/10
10/5 and 5/10
• Sine pulse
- AC operation
- DC operation
g/ms
g/ms
11.4/5 and 7.3/10
15/5 and 8/10
• Short-circuit test with fuse links of operational class gG:
DIAZED, type 5SB; NEOZED, type 5SE
with short-circuit current Ik = 1 kA acc. to IEC 60947-5-1
A
10
• Test with miniature circuit breaker with C characteristic
with short-circuit current Ik = 400 A acc. to IEC 60947-5-1
A
6
Short-circuit protection
Conductor cross-sections
Auxiliary conductors and coil terminals
(1 or 2 conductors can be connected)
Screw terminals
• Solid or stranded
• Finely stranded with end sleeve
• AWG cables, solid or stranded
mm2
mm2
AWG
2 x (0.5 ... 1.5)1), 2 x (0.75 ... 2.5)1), max. 2 x 4
2 x (0.5 ... 1.5)1), 2 x (0.75 ... 2.5)1)
2 x (20 ... 16)1), 2 x (18 ... 14)1)
• Terminal screw
- Tightening torque
Nm
M3 (for Pozidriv size 2,  5 ... 6 mm)
0.8 ... 1.2 (7 ... 10.3 lb.in)
Auxiliary conductor and coil terminals2)
(1 or 2 conductors can be connected)
Spring-type terminals
• Operating devices3)
mm
3.0 x 0.5; 3.5 x 0.5
•
•
•
•
mm2
mm2
mm2
AWG
2 x (0.5 ... 4)
2 x (0.5 ... 2.5)
2 x (0.5 ... 2.5)
2 x (20 ... 12)
Operating devices3)
mm
3.0 x 0.5; 3.5 x 0.5
•
•
•
•
mm2
mm2
mm2
AWG
2 x (0.5 ... 2.5)
2 x (0.5 ... 1.5)
2 x (0.5 ... 2.5)
2 x (20 ... 14)
Solid or stranded
Finely stranded with end sleeve
Finely stranded without end sleeve
AWG cables, solid or stranded
Auxiliary conductors for front and laterally mounted auxiliary switches2)
Solid or stranded
Finely stranded with end sleeve
Finely stranded without end sleeve
AWG cables, solid or stranded
Ring terminal lug connections
Auxiliary conductor and coil terminals
• Terminal screw
• Tightening torque
• Usable ring terminal lugs
- DIN 46234 without insulation sleeve
- DIN 46225 without insulation sleeve
- DIN 46237 with insulation sleeve
- JIS C2805 Type R without insulation sleeve
- JIS C2805 Type RAV with insulation sleeve
- JIS C2805 Type RAP with insulation sleeve
d3
d2
mm
M3, Pozidriv size 2
Nm
Ø 5 ... 6
mm
0.8 ... 1.2
mm
d2 = min. 3.2
mm
d3 = max. 7.5
I201_12740
• Operating devices
1)
If two different conductor cross-sections are connected to one clamping
point, both cross-sections must lie in one of the ranges specified.
2)
Max. external diameter of the conductor insulation: 3.6 mm.
An insulation stop must be used for spring-type terminals with conductor
cross-sections  1 mm2; see "Accessories", page 5/14.
3)
Tool for opening the spring-type terminals;
see "Accessories", page 5/14.
Siemens IC 10 · 2014
5/7
© Siemens AG 2013
Contactor Relays
SIRIUS 3RH2 contactor relays,
4- and 8-pole
Contactor relays
Type
3RH2.
Size
S00
Control circuit
Solenoid coil operating range
• AC operation
At 50 Hz
At 60 Hz
0.8 ... 1.1 x Us
0.85 ... 1.1 x Us
• DC operation
At 50 °C
At +60 °C
0.8 ... 1.1 x Us
0.85 ... 1.1 x Us
Power consumption of the solenoid coils
(for cold coil and 1.0 x Us)
• AC operation, 50 Hz
- Closing
- Closed
VA/p.f.
VA/p.f.
37/0.8
5.7/0.25
VA/p.f.
VA/p.f.
33/0.75
4.4/0.25
W
4.0
• AC operation, 60 Hz
5
- Closing
- Closed
• DC operation
closing = closed
Permissible residual current of the electronics
(with 0 signal)
• For AC operation1)
• For DC operation
< 4 mA x (230 V/Us)
< 10 mA x (24 V/Us)
Operating times2)
(Total break time = OFF-delay + Arcing time)
Values apply with coil in cold state and at operating temperature for
operating range
AC operation
• Closing
- ON-delay of NO contact
- OFF-delay of NC contact
With 0.8 ... 1.1 x Us
With 1.0 x Us
3RH24 minimum operating time
ms
ms
ms
8 ... 33
9 ... 22
35
With 0.8 ... 1.1 x Us
With 1.0 x Us
ms
ms
6 ... 25
6.5 ... 19
With 0.8 ... 1.1 x Us
With 1.0 x Us
3RH24 minimum operating time
ms
ms
ms
4 ... 15
4.5 ... 15
30
With 0.8 ... 1.1 x Us
With 1.0 x Us
ms
ms
5 ... 15
5 ... 15
With 0.8 ... 1.1 x Us
With 1.0 x Us
3RH24 minimum operating time
ms
ms
ms
30 ... 100
35 ... 50
100
With 0.8 ... 1.1 x Us
With 1.0 x Us
ms
ms
25 ... 90
30 ... 45
With 0.8 ... 1.1 x Us
With 1.0 x Us
3RH24 minimum operating time
ms
ms
ms
7 ... 13
7 ... 12
30
With 0.8 ... 1.1 x Us
With 1.0 x Us
ms
ms
13 ... 19
13 ... 18
ms
10 ... 15
• Opening
- OFF-delay of NO contact
- ON-delay of NC contact
DC operation
• Closing
- ON-delay of NO contact
- OFF-delay of NC contact
• Opening
- OFF-delay of NO contact
- ON-delay of NC contact
• Arcing time
Dependence of the switching frequency z'
on the operational current I' and operational voltage U':
z’ = z  Ie/I’  (Ue/U’)1.5  1/h
1)
2)
The 3RT2916-1GA00 additional load module is recommended
for higher residual currents; (see page 5/13).
The OFF-delay of the NO contact and the ON-delay of the NC contact are
increased if the contactor coils are attenuated against voltage peaks
(noise suppression diode 6 to 10 times;
diode assembly 2 to 6 times, varistor +2 to 5 ms).
5/8
Siemens IC 10 · 2014
© Siemens AG 2013
Contactor Relays
SIRIUS 3RH2 contactor relays,
4- and 8-pole
Contactor relays
Type
3RH2.
Size
S00
Load side
Load rating with AC
Rated operational currents Ie
AC-12
A
10
Up to 230 V
400 V
500 V
690 V
A
A
A
A
101)
3
2
1
• 1 conducting path
24 V
60 V
110 V
220 V
440 V
600 V
A
A
A
A
A
A
10
6
3
1
0.3
0.15
• 2 conducting paths in series
24 V
60 V
110 V
220 V
440 V
600 V
A
A
A
A
A
A
10
10
4
2
1.3
0.65
• 3 conducting paths in series
24 V
60 V
110 V
220 V
440 V
600 V
A
A
A
A
A
A
10
10
10
3.6
2.5
1.8
• 1 conducting path
24 V
60 V
110 V
220 V
440 V
600 V
A
A
A
A
A
A
101)
2
1
0.3
0.14
0.1
• 2 conducting paths in series
24 V
60 V
110 V
220 V
440 V
600 V
A
A
A
A
A
A
10
3.5
1.3
0.9
0.2
0.1
• 3 conducting paths in series
24 V
60 V
110 V
220 V
440 V
600 V
A
A
A
A
A
A
10
4.7
3
1.2
0.5
0.26
h-1
h-1
h-1
1 000
1 000
1 000
h-1
10 000
• Rated control supply voltage
V AC
max. 600
• Rated voltage
V AC
600
AC-15/AC-14 for rated operational voltage Us
Load rating with DC
Rated operational currents Ie
5
DC-12 for rated operational voltage Us
DC-13 for rated operational voltage Us
Switching frequency
Switching frequency z in operating cycles/hour
• For rated operation
For utilization category
• No-load switching frequency
AC-12/DC-12
AC-15/AC-14
DC-13
Dependence of the switching frequency z' on
the operational current I' and operational voltage U':
z’ = z  Ie/I’  (Ue/U’)1.5  1/h
s and u rated data
Basic units and auxiliary switch blocks
• Switching capacity
• Uninterrupted current at 240 V AC
1)
A 600, Q 600
A
10
3RH22, 3RH29: Ie = 6 A for AC-15/AC-14 and DC-13.
Siemens IC 10 · 2014
5/9
© Siemens AG 2013
Contactor Relays
SIRIUS 3RH2 contactor relays,
4- and 8-pole
■ Selection and ordering data
AC operation
PU (UNIT, SET, M) = 1
PS*
= 1 unit
PG
= 41A
Size S00
5
3RH2122-1A . .0
3RH2122-2A . .0
Rated operational current Contacts
Ie/AC-15/AC-14
Ident. No. Version
at 230 V
3RH2244-1A . .0
Article No.
A
NO
NC
3RH2244-2A . .0
DT Screw terminals1)
Rated control
supply voltage Us
at 50/60 Hz2)
DT Spring-type
terminals
Price
per PU
Article No.
Price
per PU
V AC
For screw fixing and snap-on mounting onto
TH 35 standard mounting rail
Terminal designations according to EN 50011
4 NO, Ident. No. 40E
A1(+)
A2(–)
10
3 NO + 1 NC, Ident. No. 31E
13 23 33 43
A1(+)
A2(–)
14 24 34 44
2 NO + 2 NC, Ident. No. 22E
13 21 33 43
A1(+)
13 21 31 43
A2(–)
14 22 34 44
14 22 32 44
40E
4
--
24
110
230
}
}
}
3RH2140-1AB00
3RH2140-1AF00
3RH2140-1AP00
B
B
}
3RH2140-2AB00
3RH2140-2AF00
3RH2140-2AP00
31E
3
1
24
110
230
}
}
}
3RH2131-1AB00
3RH2131-1AF00
3RH2131-1AP00
B
}
}
3RH2131-2AB00
3RH2131-2AF00
3RH2131-2AP00
22E
2
2
24
110
230
}
}
}
3RH2122-1AB00
3RH2122-1AF00
3RH2122-1AP00
B
}
}
3RH2122-2AB00
3RH2122-2AF00
3RH2122-2AP00
• With permanently mounted auxiliary switch block
4 NO + 4 NC, Ident. No. 44E
6 NO + 2 NC, Ident. No. 62E
A1(+) 13 23 33 43 53 61 71 83
A1(+) 13 23 33 43 51 61 71 81
A2(–) 14 24 34 44 54 62 72 84
A2(–) 14 24 34 44 52 62 72 82
6
44E
4
4
230
}
3RH2244-1AP00
A
3RH2244-2AP00
62E
6
2
230
}
3RH2262-1AP00
A
3RH2262-2AP00
1)
The 3RH21/3RH22 contactor relays are also available with ring terminal lug
connection. Please contact your local Siemens representative for information about the special contactor versions with ring terminal lug connection.
2)
Coil operating range
at 50 Hz: 0.8 to 1.1 x Us
at 60 Hz: 0.85 to 1.1 x Us.
5/10
Siemens IC 10 · 2014
Other voltages according to page 5/12 on request.
Accessories see pages 5/12 to 5/14 and
"Accessories for 3RT2 Contactors", Chapter 3.
* You can order this quantity or a multiple thereof.
Illustrations are approximate
© Siemens AG 2013
Contactor Relays
SIRIUS 3RH2 contactor relays,
4- and 8-pole
DC operation
PU (UNIT, SET, M) = 1
PS*
= 1 unit
PG
= 41A
Size S00
3RH2122-2B. .0
3RH2244-1B. .0
Rated operational current Contacts
Ie/AC-15/AC-14
Ident. No. Version
at 230 V
Rated control
supply voltage Us
A
V DC
NO
NC
3RH2244-2B. .0
DT Screw terminals1)
Article No.
DT Spring-type
terminals
Price
per PU
Article No.
Price
per PU
For screw fixing and snap-on mounting onto
TH 35 standard mounting rail
Terminal designations according to EN 50011
4 NO, Ident. No. 40E
A1(+)
A2(–)
10
3 NO + 1 NC, Ident. No. 31E
13 23 33 43
A1(+)
A2(–)
14 24 34 44
2 NO + 2 NC, Ident. No. 22E
13 21 33 43
A1(+)
A2(–)
14 22 34 44
13 21 31 43
14 22 32 44
40E
4
--
24
220
}
}
3RH2140-1BB40
3RH2140-1BM40
}
B
3RH2140-2BB40
3RH2140-2BM40
31E
3
1
24
220
}
A
3RH2131-1BB40
3RH2131-1BM40
}
B
3RH2131-2BB40
3RH2131-2BM40
22E
2
2
24
220
}
}
3RH2122-1BB40
3RH2122-1BM40
}
B
3RH2122-2BB40
3RH2122-2BM40
• With permanently mounted auxiliary switch block
4 NO + 4 NC, Ident. No. 44E
6 NO + 2 NC, Ident. No. 62E
A1(+) 13 23 33 43 53 61 71 83
A1(+) 13 23 33 43 51 61 71 81
A2(–) 14 24 34 44 54 62 72 84
A2(–) 14 24 34 44 52 62 72 82
6
1)
44E
4
4
24
}
3RH2244-1BB40
}
3RH2244-2BB40
62E
6
2
24
}
3RH2262-1BB40
}
3RH2262-2BB40
The 3RH21/3RH22 contactor relays are also available with ring terminal lug
connection. Please contact your local Siemens representative for information about the special contactor versions with ring terminal lug connection.
* You can order this quantity or a multiple thereof.
Illustrations are approximate
Other voltages according to page 5/12 on request.
Accessories see pages 5/12 to 5/14 and
"Accessories for 3RT2 Contactors", Chapter 3.
Siemens IC 10 · 2014
5/11
5
3RH2122-1B. .0
© Siemens AG 2013
Contactor Relays
SIRIUS 3RH2 contactor relays,
4- and 8-pole
■ Options
Rated control supply voltages (change of 10th and 11th digit of the Article No.)
Contactor type
Rated control
supply voltage Us
3RH21, 3RH22
Contactor type
Rated control
supply voltage Us
Control supply voltage at
AC operation
DC operation
Solenoid coils for 50/60 Hz and 60 Hz
50/60 Hz1)
60 Hz
12 V DC
24 V DC
42 V DC
A4
B4
D4
24 V AC
42 V AC
48 V AC
----
B0
D0
H0
48 V DC
60 V DC
110 V DC
W4
E4
F4
110 V AC
220 V AC
230 V AC
----
F0
N2
P0
125 V DC
220 V DC
230 V DC
G4
M4
P4
400 V AC
--
V0
Solenoid coils for USA and Canada2)
5
3RH21, 3RH22
Control supply voltage at
50 Hz
60 Hz
110 V AC
220 V AC
120 V AC
240 V AC
Solenoid coils for
K6
P6
Japan3)
50/60 Hz
60 Hz
100 V AC
200 V AC
400 V AC
110 V AC
220 V AC
440 V AC
G6
N6
R6
1)
Coil operating range
at 50 Hz: 0.8 to 1.1 x Us
at 60 Hz: 0.85 to 1.1 x Us.
2) Coil operating range
at 50 Hz: 0.85 to 1.1 x Us
at 60 Hz: 0.8 to 1.1 x Us.
3)
Coil operating range
at 50/60 Hz: 0.85 to 1.1 x Us
at 60 Hz: 0.8 to 1.1 x Us.
■ Accessories
The auxiliary switch blocks according to EN 50011 listed here
should preferably be used for 3RH2 contactor relays.
For auxiliary switch blocks and solid-state compatible auxiliary
switch blocks according to EN 50005 see "Accessories for 3RT2
Contactors", Chapter 3.
PU (UNIT, SET, M) = 1
PS*
= 1 unit
PG
= 41B
3RH2911-1GA22
For contactor
relays
Contactor relays
with AS block
Auxiliary contacts
Ident. No.
Version
Article No.
Type
NO
3RH2911-2GA22
DT Screw terminals
DT Spring-type
terminals
Price
per PU
Article No.
Price
per PU
NC
Auxiliary switch blocks for snapping onto the front acc. to EN 50011
Blocks for the assembly of contactor relays with 8 contacts1)
3RH2140,
3RH2440,
Ident. No. 40E
80E
4
--
53 63 73 83
71E
3
1
53 61 73 83
62E
2
2
53 61 71 83
53E
1
3
53 61 71 81
44E
--
4
51 61 71 81
}
3RH2911-1GA40
}
3RH2911-2GA40
}
3RH2911-1GA31
}
3RH2911-2GA31
}
3RH2911-1GA22
}
3RH2911-2GA22
}
3RH2911-1GA13
}
3RH2911-2GA13
}
3RH2911-1GA04
}
3RH2911-2GA04
54 64 74 84
54 62 74 84
54 62 72 84
54 62 72 82
52 62 72 82
1)
The 3RH2911-.GA.. auxiliary switches are also available with ring terminal
lug connection. The 8th digit of the Article No. must be changed from a "1"
to a "4", e.g. 3RH2911-1GA22 ➞ 3RH2911-4GA22.
5/12
Siemens IC 10 · 2014
* You can order this quantity or a multiple thereof.
Illustrations are approximate
© Siemens AG 2013
Contactor Relays
SIRIUS 3RH2 contactor relays,
4- and 8-pole
More accessory parts see "Accessories for 3RT2 Contactors in
Size S00", Chapter 3.
The following accessory parts are accessories for 3RT2 contactors in size S00, which are also suitable for 3RH2 contactor
relays.
For
Version
contactors
Rated control supply voltage Us1) DT Article No.2)
AC operation
DC operation
Type
V AC
V DC
Price
per PU
PU
(UNIT,
SET,
M)
PS*
PG
Surge suppressors without LED
(also for spring-type terminals)
3RH2.
Varistor
24 ... 48
48 ... 127
127 ... 240
240 ... 400
400 ... 600
24 ... 70
70 ... 150
150 ... 250
---
}
}
}
}
A
3RT2916-1BB00
3RT2916-1BC00
3RT2916-1BD00
3RT2916-1BE00
3RT2916-1BF00
1
1
1
1
1
1 unit
1 unit
1 unit
1 unit
1 unit
41B
41B
41B
41B
41B
3RH2.
RC elements
24 ... 48
48 ... 127
127 ... 240
240 ... 400
400 ... 600
24 ... 70
70 ... 150
150 ... 250
---
}
}
}
A
A
3RT2916-1CB00
3RT2916-1CC00
3RT2916-1CD00
3RT2916-1CE00
3RT2916-1CF00
1
1
1
1
1
1 unit
1 unit
1 unit
1 unit
1 unit
41B
41B
41B
41B
41B
3RH2.
Noise suppression diode
--
12 ... 250
}
3RT2916-1DG00
1
1 unit
41B
3RH2.
Diode assemblies
(diode and Zener diode) for
DC operation
--
12 ... 250
}
3RT2916-1EH00
1
1 unit
41B
PU
(UNIT,
SET,
M)
PS*
PG
3RT2916-1B.00
1)
Can be used for AC operation for 50/60 Hz. Please inquire about further
voltages.
2)
For packs of 10 or 5 units, "-Z" and order code "X90" must be added to the
Article No.
For
Version
contactors
Type
Rated control
supply voltage Us1)
AC
operation
DC
operation
Power
consumption P
of the LED
at Us
V AC
V DC
mW
DT Article No.2)
Price
per PU
Surge suppressors with LED
(also for spring-type terminals)
For plugging onto the front side of the contactors
(with and without auxiliary switch block)
3RH2.
Varistor
24 ... 48
48 ... 127
127 ... 240
--
12 ... 24
24 ... 70
70 ... 150
150 ... 250
10 ... 120
20 ... 470
50 ... 700
160 ... 950
}
}
}
A
3RT2916-1JJ00
3RT2916-1JK00
3RT2916-1JL00
3RT2916-1JP00
1
1
1
1
1 unit
1 unit
1 unit
1 unit
41B
41B
41B
41B
3RH2.
Noise
suppression
diode
----
24 ... 70
50 ... 150
150 ... 250
20 ... 470
50 ... 700
160 ... 950
}
A
}
3RT2916-1LM00
3RT2916-1LN00
3RT2916-1LP00
1
1
1
1 unit
1 unit
1 unit
41B
41B
41B
PU
(UNIT,
SET,
M)
PS*
PG
1
1 unit
41B
3RT2916-1J.00
1)
Can be used for AC operation for 50/60 Hz. Please inquire about further
voltages.
2)
For packs of 10 or 5 units, "-Z" and order code "X90" must be added to the
Article No.
For
Version
contactors
DT Article No.
Price
per PU
Type
Additional load modules
3RH2.
For plugging onto the front side of the contactors
with or without auxiliary switch blocks1)
}
3RT2916-1GA00
For increasing the permissible residual current and for limiting
the residual voltage. It ensures the safe opening of contactors
with direct control via 230 V AC semiconductor outputs on
SIMATIC controllers. It acts simultaneously as a surge suppressor.
Rated voltage: AC 50/60 Hz, 180 to 255 V.
Operating range: 0.8 to 1.1 x Us
3RT2916-1GA00
1)
For packs of 10 units, "-Z" and order code "X90" must be added to the
Article No.
* You can order this quantity or a multiple thereof.
Illustrations are approximate
Siemens IC 10 · 2014
5/13
5
For plugging onto the front side of the contactors
(with and without auxiliary switch block)
© Siemens AG 2013
Contactor Relays
SIRIUS 3RH2 contactor relays,
4- and 8-pole
For contactors
Rated control supply Time setting
voltage Us
range t
Type
V
DT Screw terminals
Article No.
PU
(UNIT,
SET,
M)
PS*
PG
Price
per PU
s
OFF-delay devices
For contactor relays with DC operation
Non-adjustable delay time
3RH2. . .-1BF40
110 AC/DC
S00: > 0.1
B
3RT2916-2BK01
1
1 unit
41B
B
3RT2916-2BL01
1
1 unit
41B
A
3RT2916-2BE01
1
1 unit
41B
PU
(UNIT,
SET,
M)
PS*
PG
S0: > 0.08
3RH2. . .-1BM40
220/230 AC/DC
S00: > 0.5
S0: > 0.3
3RH2. . .-1BB40
24 DC
S00: > 0.2
5
S0: > 0.1
3RT2916-2B.01
For technical specifications, see "Accessories for 3RT20
Contactors", Chapter 3.
For contactors
Version
DT Article No.
Price
per PU
3RH2.
For manual operation of the contactor
contacts for start-up and service
A
3RT2916-4MC00
1
5 units
41B
3RH2. 1)
Sealable covers
for preventing manual operation
A
3RT2916-4MA10
1
5 units
41B
Type
Control kit
3RT2916-4MC00
Sealable covers
Not suitable for coupling relays
3RT2916-4MA10
1)
Exception: contactors and contactor relays auxiliary switch block mounted
onto the front.
Version
DT Spring-type terminals
Article No.
PU
(UNIT,
SET,
M)
PS*
PG
Price
per PU
Insulation stop for securely holding back the conductor insulation
on conductors up to 1 mm2
Insulation stop strip can be inserted in cable entry of the
spring-type terminal
(2 strips per contactor required)
3RT2916-4JA02
• For basic units S00 (3RT201. or 3RH2.),
removable individually
B
3RT2916-4JA02
1 20 units
41B
A
3RA2908-1A
1
41B
Tools for opening spring-type terminals
Screwdrivers
for all SIRIUS devices with spring-type terminals
Length: approx. 200 mm,
3.0 mm x 0.5 mm,
titanium gray/black, partially insulated
1 unit
3RA2908-1A
5/14
Siemens IC 10 · 2014
* You can order this quantity or a multiple thereof.
Illustrations are approximate
© Siemens AG 2013
Contactor Relays
SIRIUS 3RH24 latched contactor relays,
4-pole
■ Overview
Standards
Control circuit
IEC 60947-1, EN 60947-1,
IEC 60947-5-1, EN 60947-5-1
The contactor coil and the coil of the release solenoid are both
designed for uninterrupted duty.
The terminal designations comply with EN 50011.
RC elements, varistors, diodes or diode assemblies can be fitted
to both coils from the front for damping opening surges in the
coil.
Auxiliary switches
The number of auxiliary contacts can be extended by means of
auxiliary switch blocks on the front (up to four contacts).
The contactor relay can also be switched on and released manually. Minimum actuating times, see "Technical Specifications",
page 5/8.
5
■ Selection and ordering data
3RH2422-1A. . 0
Rated operational
current
Ie/AC-15/AC-14
at 230 V
Contacts
Rated control supply
voltage Us
Ident. No. acc. to Version
EN 50011
DT Screw terminals
Article No.
A
NO
NC
PU
(UNIT,
SET,
M)
PS*
PG
Price
per PU
V
For screw fixing and snap-on mounting onto TH 35 standard mounting rail
Terminal designations according to EN 50011
4 NO, Ident. No. 40E
3 NO + 1 NC, Ident. No. 31E
2 NO + 2 NC, Ident. No. 22E
E1(+) A1+
( ) 13 23 33 43
E1(+) A1(+) 13 21 33 43
E1(+) A1(+) 13 21 31 43
E2(-) A2(-) 14 24 34 44
E2(–) A2(–) 14 22 34 44
E2(–) A2(–) 14 22 32 44
AC operation
AC 50/60 Hz1)
10
40 E
4
--
24
110
230
B
B
B
3RH2440-1AB00
3RH2440-1AF00
3RH2440-1AP00
1
1
1
1 unit
1 unit
1 unit
41A
41A
41A
31 E
3
1
24
110
230
B
B
B
3RH2431-1AB00
3RH2431-1AF00
3RH2431-1AP00
1
1
1
1 unit
1 unit
1 unit
41A
41A
41A
22 E
2
2
24
110
230
B
B
B
3RH2422-1AB00
3RH2422-1AF00
3RH2422-1AP00
1
1
1
1 unit
1 unit
1 unit
41A
41A
41A
40 E
4
--
24
110
220
B
B
B
3RH2440-1BB40
3RH2440-1BF40
3RH2440-1BM40
1
1
1
1 unit
1 unit
1 unit
41A
41A
41A
31 E
3
1
24
110
220
B
B
B
3RH2431-1BB40
3RH2431-1BF40
3RH2431-1BM40
1
1
1
1 unit
1 unit
1 unit
41A
41A
41A
22 E
2
2
24
110
220
B
B
B
3RH2422-1BB40
3RH2422-1BF40
3RH2422-1BM40
1
1
1
1 unit
1 unit
1 unit
41A
41A
41A
DC operation
DC
10
1)
Coil operating range
at 50 Hz: 0.8 to 1.1 x Us
at 60 Hz: 0.85 to 1.1 × Us.
* You can order this quantity or a multiple thereof.
Illustrations are approximate
Accessories see pages 5/12 and 5/13.
Siemens IC 10 · 2014
5/15
© Siemens AG 2013
Contactor Relays
3TH4 contactor relays,
8- and 10-pole
■ Overview
Standards
Surge suppression
IEC 60947-1, EN 60947-1,
IEC 60947-5-1, EN 60947-5-1
The 3TH42 and 3TH43 contactor relays are suitable for use in
any climate. They are finger-safe according to EN 50274.
The 3TH42 and 3TH43 contactor relays can be equipped with
RC elements, varistors, diodes or diode assemblies (combination of a diode and a Zener diode) for damping opening surges.
The surge suppressors can be mounted directly on the coil
(see "Accessories", page 5/22).
Terminal designations according to EN 50011
Note:
In terms of their terminal designations, identification numbers
and identification letters, the 3TH42 and 3TH43 contactor relays
conform to the standard EN 50011 for Specific Contactor Relays.
The OFF-delay of the NO contact and the ON-delay of the NC
contact are increased if the contactor coils are attenuated
against voltage peaks (noise suppression diode 6 to 10 times;
diode assembly 2 to 6 times, varistor +2 to 5 ms).
Contact reliability
■ Technical specifications
Contactor relays
Type
3TH42, 3TH43
Contact endurance for AC-15/AC-14 and
DC-13 utilization categories
The contact endurance is mainly dependent on the breaking current.
It is assumed that the operating mechanisms are switched randomly,
i.e. not synchronized with the phase angle of the supply system.
If magnetic circuits other than the contactor coil systems or solenoid valves
are present, e.g. magnetic brakes, protective measures for the load circuits
are necessary.
RC elements or freewheel diodes are suitable as protective measures for the
circuits.
30
Million operating cycles (106 )
5
High contact stability at low voltages and currents thanks to the
use of moving double-break contacts, suitable for solid-state
circuits with currents  1 mA at a voltage of  17 V.
NSB0_01391a
10
2
AC-15/AC-14
DC-13
5
4
3
110 V
DC-13
24 V
DC-13
220 V
1
0,5
0,1
0,01
0,03 0,05
0,1
0,3
e – DC-13
220 V
0,5
1
e – DC-13
110 V
2
3 4 5 7 10
e – DC-13
24 V
e
– AC-15/AC-14
≤ 230 V
Diagram legend:
Prated = Rated power for squirrel-cage motors at 400 V
a = Breaking current
e = Rated operational current
5/16
Siemens IC 10 · 2014
a
(A)
© Siemens AG 2013
Contactor Relays
3TH4 contactor relays,
8- and 10-pole
Type
3TH42
3TH43
mm
45 x 78 x 97
55 x 78 x 97
mm
45 x 78 x 130
55 x 78 x 130
H
Dimensions (W x H x D)
• DC operation
W
D
• AC operation
General technical specifications
Permissible mounting position
360°
22,5° 22,5°
• DC operation
22,5° 22,5°
90°
5
90°
NSB0_00649a
• AC operation
NSB0_00478c
The contactor relays are designed for operation on a
vertical mounting surface.
Upright mounting position
AC and DC operation
NSB0_00477a
Mechanical endurance
Basic units
Special version required
Operating 30 million
cycles
V
690
Rated impulse withstand voltage Uimp
kV
8
Protective separation between the coil and the main contacts
acc. to IEC 60947-1, Appendix N
V
Up to 500
• During operation
°C
-25 ... +55
• During storage
°C
-55 ... +80
Rated insulation voltage Ui
(pollution degree 3)
Permissible ambient temperature
Degree of protection acc. to IEC 60947-1, Appendix C
IP20
Shock resistance
• Rectangular pulse
- AC operation
- DC operation
g/ms
g/ms
7.7/5 and 4.4/10
9.3/5 and 5.4/10
g/ms
g/ms
12/5 and 6.8/10
14.7/5 and 8.5/10
A
A
A
16
16
20
A
A
16
16
• Sine pulse
- AC operation
- DC operation
Short-circuit protection
Short-circuit test
• with fuse links of operational class gG
with short-circuit current Ik = 1 kA acc. to IEC 60947-5-1
- LV HRC, type 3NA
- DIAZED, type 5SB
- NEOZED Type 5SE, quick
• with miniature circuit breaker
with short-circuit current Ik = 400 A acc. to IEC 60947-5-1
- C Characteristic
- B Characteristic
s and u rated data
Basic units
Rated control supply voltage Us
Max. 600 V AC, 230 V DC (acc. to UL 240 V DC)
Rated voltage
600 V AC, 600 V DC
Switching capacity
A 600, P 600
Conductor cross-sections
Screw terminals
• Solid or stranded
• Finely stranded with end sleeve
• Terminal screw
1)
mm2
2
mm
2 x (0.5 ... 1)1); 2 x (1 ... 2.5)1); 1 x 4
2 x (0.75 ... 2.5)
M3.5
If two different conductor cross-sections are connected to one clamping
point, both cross-sections must lie in one of the ranges specified.
Siemens IC 10 · 2014
5/17
© Siemens AG 2013
Contactor Relays
3TH4 contactor relays,
8- and 10-pole
Contactor relays
Type
3TH42, 3TH43
Control circuit
Solenoid coil operating range
AC operation
0.8 ... 1.1 x Us1)
DC operation (except 24 V)
• At 24 V DC
0.8 ... 1.1 x Us
0.8 ... 1.2 x Us
5
Power consumption of the solenoid coils (for cold coil and 1.0 x Us)
• AC operation, 50 Hz, standard version
- Closing
- Closed
VA/p.f.
VA/p.f.
68/0.82
10/0.29
• AC operation, 50/60 Hz, standard version
- Closing, 50 Hz
- Closed, 50 Hz
- Closing, 60 Hz
- Closed, 60 Hz
VA/p.f.
VA/p.f.
VA/p.f.
VA/p.f.
77/0.81
11/0.28
71/0.75
9/0.27
• AC operation, 50 Hz, USA/Canada
- Closing
- Closed
VA/p.f.
VA/p.f.
68/0.82
10/0.29
• AC operation, 60 Hz, USA/Canada
- Closing
- Closed
VA/p.f.
VA/p.f.
75/0.76
9,4/0.29 ... 0.3
• AC operation, 50 Hz, standard version
- Closing
- Closed
VA/p.f.
VA/p.f.
80/0.8
10,7/0.29
• AC operation, 60 Hz, standard version
- Closing
- Closed
VA/p.f.
VA/p.f.
75 ... 90/0.73
8,5 ... 10,7/0.29 ... 0.3
W
6.2
• DC operation up to 250 V
Closing = Closed
Permissible residual current of the electronics (with 0 signal)
 8 mA x (220 V/Us)
 1.25 mA x (220 V/Us)
• For AC operation
• For DC operation
Operating times2)
Total break time = OFF-delay + arcing time
(the values apply up to and including 20 % undervoltage, 10 % overvoltage, and with the coil in the cold state and at operating temperature)
AC operation
• Closing
- ON-delay NO
- OFF-delay NC
ms
ms
8 ... 35
6 ... 20
• Opening
- OFF-delay NO
- ON-delay NC
ms
ms
4 ... 18
5 ... 30
• Arcing time
ms
10
• Closing
- ON-delay NO
- OFF-delay NC
ms
ms
20 ... 170
18 ... 110
• Opening
- OFF-delay NO
- ON-delay NC
ms
ms
10 ... 25
15 ... 30
Arcing time
ms
10
• Closing
- ON-delay NO
- OFF-delay NC
ms
ms
10 ... 25
7 ... 20
• Opening
- OFF-delay NO
- ON-delay NC
ms
ms
5 ... 18
7 ... 20
• Closing
- ON-delay NO
- OFF-delay NC
ms
ms
30 ... 70
28 ... 65
• Opening
- OFF-delay NO
- ON-delay NC
ms
ms
10 ... 20
15 ... 25
DC operation
Operating times2) at 1.0 x Us
AC operation
DC operation
1)
Coils for USA, Canada and Japan: 0.85 ... 1.1 Us at 60 Hz.
2)
The OFF-delay of the NO contact and the ON-delay of the NC contact are
increased if the contactor coils are attenuated against voltage peaks
(noise suppression diode 6 to 9 times;
diode assembly 2 to 6 times, varistor +2 to 5 ms).
5/18
Siemens IC 10 · 2014
© Siemens AG 2013
Contactor Relays
3TH4 contactor relays,
8- and 10-pole
Contactor relays
Type
3TH42, 3TH43
Load side
Load rating with AC
Rated operational currents Ie
AC-12
A
16
A
A
A
A
10
6
4
2
230/220 V
400/380 V
500 V
690/660 V
kW
kW
kW
kW
2.4
4
4
4
Up to 48 V
110 V
220 V
440 V
A
A
A
A
10
2.1
0.8
0.6
Up to 48 V
110 V
220 V
440 V
A
A
A
A
10
10
1.6
0.8
Up to 48 V
110 V
220 V
440 V
A
A
A
A
10
10
10
1.3
Up to 24 V
48 V
110 V
220 V
440 V
600 V
A
A
A
A
A
A
10
5
1
0.45
0.25
0.2
Up to 24 V
48 V
110 V
220 V
440 V
600 V
A
A
A
A
A
A
10
10
2.5
0.75
0.5
0.4
Up to 24 V
48 V
110 V
220 V
440 V
600 V
A
A
A
A
A
A
10
10
10
2
0.9
0.8
AC-12/DC-12
AC-2
AC-3
AC-15/AC-14
DC-13
h-1
h-1
h-1
h-1
h-1
1 000
500
1 000
3 600
3 600
No-load switching
frequency
h-1
10 000
AC-15/AC-14 for rated operational voltage Ue
230 V
400 V
500 V
690 V
Rated power of three-phase motors
Acc. to utilization categories AC-2 and AC-3, 50 Hz
Load rating with DC
5
Rated operational currents Ie
DC-12, for rated operational voltage Ue
• 1 conducting path
• 2 conducting paths in series
• 3 conducting paths in series
DC-13, for rated operational voltage Ue
• 1 conducting path
• 2 conducting paths in series
• 3 conducting paths in series
Switching frequency
Switching frequency z1) in operating cycles/hour
For rated operation
For utilization category
1)
Dependence of the switching frequency z' on the operational current I' and
operational voltage U': z' = z Ie/I'  (Ue/U')1.5  1/h.
Siemens IC 10 · 2014
5/19
© Siemens AG 2013
Contactor Relays
3TH4 contactor relays,
8- and 10-pole
■ Selection and ordering data
8-pole contactor relays
3TH4244-0B. .
5
Contacts
Number
Rated operational current
Ie/AC-15/AC-14
at
230/
220 V
400/
380 V
500 V
690/
660 V
A
A
A
A
Contacts
DT Screw terminals
Ident. No. acc. to Version
EN 50011
NO
Article No.
NC
NO
PU
(UNIT,
SET,
M)
PS*
PG
Price
per PU
NC
For screw fixing and snap-on mounting onto TH 35 standard mounting rail
Terminal designations according to EN 50011
8 NO, Ident. No. 80E
7 NO + 1 NC, Ident. No. 71E
A1(+) 13 23 33 43 53 63 73 83
A2( )
A1(+)
A2( )
14 24 34 44 54 64 74 84
5 NO + 3 NC, Ident. No. 53E
A1(+)
6 NO + 2 NC, Ident. No. 62E
13 23 33 43 53 61 73 83
A1(+)
A2( )
14 24 34 44 54 62 74 84
4 NO + 4 NC, Ident. No. 44E
13 23 33 43 53 61 71 81
A1(+)
A2( )
14 24 34 44 54 62 72 82
13 23 33 43 51 61 71 81
14 24 34 44 52 62 72 82
AC operation, rated control supply voltage Us = 50 Hz 230/220 V
8
10
6
4
2
14 24 34 44 54 62 72 84
3 NO + 3 NC and 1 NO + 1 NC make-before-break,
Ident. No. 44E, U
A1(+)
A2( )
13 23 33 43 53 61 71 83
A2( )
13 23 33 47 51 61 71 85
14 24 34 48 52 62 72 86
AC1)
80 E
71 E
62 E
53 E
8
7
6
5
-1
2
3
-----
-----
}
}
}
}
3TH4280-0AP0
3TH4271-0AP0
3TH4262-0AP0
3TH4253-0AP0
1
1
1
1
1 unit
1 unit
1 unit
1 unit
41A
41A
41A
41A
44 E
44 E, U
4
3
4
3
-1
-1
}
}
3TH4244-0AP0
3TH4293-0AP0
1
1
1 unit
1 unit
41A
41A
DC operation, rated control supply voltage Us = 24 V DC
8
1)
10
6
4
2
80 E
71 E
62 E
53 E
8
7
6
5
-1
2
3
-----
-----
}
}
}
}
3TH4280-0BB4
3TH4271-0BB4
3TH4262-0BB4
3TH4253-0BB4
1
1
1
1
1 unit
1 unit
1 unit
1 unit
41A
41A
41A
41A
44 E
44 E, U
4
3
4
3
-1
-1
}
}
3TH4244-0BB4
3TH4293-0BB4
1
1
1 unit
1 unit
41A
41A
Operating range at 220 V: 0.85 to 1.1 x Us;
lower operating range limit according to IEC 60947.
Note:
The solenoid coils of the 3TH42 contactor relays are available in
various voltages as spare parts (on request).
- AC operation: 3TY7403-0A..
- DC operation: 3TY4803-0B..
The contacts cannot be replaced on 3TH42 contactor relays.
5/20
Siemens IC 10 · 2014
Other voltages according to page 5/22 on request.
Accessories see pages 5/22 and 5/23.
* You can order this quantity or a multiple thereof.
Illustrations are approximate
© Siemens AG 2013
Contactor Relays
3TH4 contactor relays,
8- and 10-pole
10-pole contactor relays
3TH4355-0A. .
Rated operational current
Ie/AC-15/AC-14
at
Contacts
230 V
400 V
500 V
690 V
A
A
A
A
3TH4355-0B. .
DT Screw terminals
Ident. No. acc. to Version
EN 50011
Article No.
PU
(UNIT,
SET,
M)
PS*
PG
Price
per PU
5
Contacts
Number
NO
NC
NO
NC
For screw fixing and snap-on mounting onto TH 35 standard mounting rail
Terminal designations according to EN 50011
10 NO, Ident. No. 100E
A1(+)
A2( )
A1(+)
A2( )
14 24 34 44 54 64 74 84 94 04
7 NO + 3 NC, Ident. No. 73E
A1(+)
A2( )
8 NO + 2 NC, Ident. No. 82E
9 NO + 1 NC, Ident. No. 91E
13 23 33 43 53 63 73 83 93 03
13 23 33 43 53 63 71 83 93 03
A1(+)
A2( )
14 24 34 44 54 64 72 84 94 04
6 NO + 4 NC, Ident. No. 64E
13 23 33 43 53 63 71 81 91 03
A1(+)
A2( )
14 24 34 44 54 64 72 82 92 04
A2( )
13 23 33 43 53 63 71 81 91 01
A1(+)
A2( )
14 24 34 44 54 64 72 82 92 02
13 23 37 43 53 63 71 85 91 03
A1(+)
A2( )
14 24 38 44 54 64 72 86 92 04
10
6
4
2
13 23 33 43 53 61 71 81 91 01
14 24 34 44 54 62 72 82 92 02
4 NO + 4 NC and 1 NO + 1 NC make-before-break,
Ident. No. 44E, 11U
AC operation, rated control supply voltage Us = 50 Hz 230/220 V AC
10
14 24 34 44 54 64 72 84 92 04
5 NO + 5 NC, Ident. No. 55E
6 NO + 2 NC and 1 NO + 1 NC
make-before-break, Ident. No. 63E, 11U
A1(+)
13 23 33 43 53 63 71 83 91 03
13 23 37 43 53 61 71 85 91 01
14 24 38 44 54 62 72 86 92 02
1)
100 E
91 E
82 E
73 E
73 E, U
10
9
8
7
6
-1
2
3
2
----1
----1
}
}
}
}
}
3TH4310-0AP0
3TH4391-0AP0
3TH4382-0AP0
3TH4373-0AP0
3TH4346-0AP0
1
1
1
1
1
1 unit
1 unit
1 unit
1 unit
1 unit
41A
41A
41A
41A
41A
64 E
55 E
55 E, U
6
5
4
4
5
4
--1
--1
}
}
}
3TH4364-0AP0
3TH4355-0AP0
3TH4394-0AP0
1
1
1
1 unit
1 unit
1 unit
41A
41A
41A
DC operation, rated control supply voltage Us = 24 V DC1)
10
1)
10
6
4
2
100 E
91 E
82 E
73 E
73 E, U
10
9
8
7
6
-1
2
3
2
----1
----1
}
}
}
}
}
3TH4310-0BB4
3TH4391-0BB4
3TH4382-0BB4
3TH4373-0BB4
3TH4346-0BB4
1
1
1
1
1
1 unit
1 unit
1 unit
1 unit
1 unit
41A
41A
41A
41A
41A
64 E
55 E
55 E, U
6
5
4
4
5
4
--1
--1
}
}
}
3TH4364-0BB4
3TH4355-0BB4
3TH4394-0BB4
1
1
1
1 unit
1 unit
1 unit
41A
41A
41A
Operating range at 220 V: 0.85 to 1.1 x Us;
lower operating range limit according to IEC 60947.
Note:
The solenoid coils of the 3TH43 contactor relays are available in
various voltages as spare parts (on request).
- AC operation: 3TY7403-0A..
- DC operation: 3TY4803-0B..
The contacts cannot be replaced on 3TH43 contactor relays.
* You can order this quantity or a multiple thereof.
Illustrations are approximate
Other voltages according to page 5/22 on request.
Accessories see pages 5/22 and 5/23.
Siemens IC 10 · 2014
5/21
© Siemens AG 2013
Contactor Relays
3TH4 contactor relays,
8- and 10-pole
■ Options
Rated control supply voltages
(change of 10th and 11th digit of the Article No.)
Contactor type
Rated control
supply voltage Us
3TH42/3TH43
Contactor type
Solenoid coils for AC 50 and 60 Hz
AC operation
50/60 Hz
Solenoid coils for AC 50 Hz
5
50 Hz
60 Hz
24 V AC
36 V AC
42 V AC
29 V AC
42 V AC
50 V AC
B0
G0
D0
48 V AC
60 V AC
110 V AC
58 V AC
72 V AC
132 V AC
H0
E0
F0
125/127 V AC
230/220 V AC
240 V AC
150/152 V AC
276 V AC
288 V AC
L0
P01)
U0
400/380 V AC
415 V AC
500 V AC
480/460 V AC
500 V AC
600 V AC
V01)
R0
S0
100-110 V AC
200-220 V AC
G62)
N62)
120 V AC
240 V AC
K62)
P62)
For USA and Canada
110 V AC
220 V AC
1)
Operating range at 220 V or 380 V: 0.85 to 1.1 x Us.
2)
Operating range at 60 Hz: 0.85 to 1.1 x Us.
24 V AC
42 V AC
110 V AC
C2
D2
G2
115 V AC
120 V AC
220 V AC
J2
K2
N2
230 V AC
240 V AC
440 V AC
L2
P2
R2
DC operation
For Japan
100 V AC
200 V AC
3TH42/3TH43
Rated control
supply voltage Us
Control supply voltage at
12 V DC
24 V DC
30 V DC
A4
B4
C4
36 V DC
42 V DC
48 V DC
V4
D4
W4
60 V DC
110 V DC
125 V DC
E4
F4
G4
220 V DC
230 V DC
240 V DC
M4
P4
Q4
■ Accessories
Version
Rated control supply
voltage Us
DT Article No.
Price
per PU
PU
(UNIT,
SET,
M)
PS*
PG
AC
DC
V
V
Noise suppression diodes
with line spacer,
for mounting onto the coil terminal
--
24 ... 250
A
3TX7402-3A
1
1 unit
41B
Diode assemblies
(diode and Zener diode) with line spacer,
DC operation,
for mounting onto the coil terminal
--
24 ... 250
A
3TX7402-3D
1
1 unit
41B
Varistors2)
with line spacer,
for mounting onto the coil terminal
24 ... 48
48 ... 127
127 ... 240
240 ... 400
400 ... 600
24 ... 70
70 ... 150
150 ... 250
---
A
A
A
C
C
3TX7402-3G
3TX7402-3H
3TX7402-3J
3TX7402-3K
3TX7402-3L
1
1
1
1
1
1 unit
1 unit
1 unit
1 unit
1 unit
41B
41B
41B
41B
41B
RC elements
with line spacer,
for mounting onto the coil terminal
24 ... 48
48 ... 127
127 ... 240
240 ... 400
400 ... 600
24 ... 70
70 ... 150
150 ... 250
---
A
A
A
B
C
3TX7402-3R
3TX7402-3S
3TX7402-3T
3TX7402-3U
3TX7402-3V
1
1
1
1
1
1 unit
1 unit
1 unit
1 unit
1 unit
41B
41B
41B
41B
41B
Covers
for switch position indicator
--
--
X
3TX4210-0P
1
1 unit
41B
Surge suppressors1) for 3TH4 contactor relays
3TX7402-3.
1)
The OFF-delay of the NO contact and the ON-delay of the NC contact are
increased if the contactor coils are attenuated against voltage peaks
(noise suppression diode 6 to 10 times;
diode assembly 2 to 6 times, varistor +2 to 5 ms).
2)
Includes the peak value of the alternating voltage on the DC side.
5/22
Siemens IC 10 · 2014
* You can order this quantity or a multiple thereof.
Illustrations are approximate
© Siemens AG 2013
Contactor Relays
3TH4 contactor relays,
8- and 10-pole
For
contactors
Version
Rated control supply Time setting
voltage Us
range
AC 50/60 Hz
(minimum
times)
DT Screw terminals
Article No.
Type
V
s
220 ... 230
0.1
PU
(UNIT,
SET,
M)
PS*
PG
Price
per PU
ON-delay devices
3TH42,
3TH43
B
3TX4180-0A
1
1 unit
41B
• For mounting directly onto contactor coil
without surge suppressor
A
3TX4090-0C
1
1 unit
41B
• For mounting directly onto contactor coil
with surge suppressor
A
3TX4090-0D
1
1 unit
41B
PU
(UNIT,
SET,
M)
PS*
PG
NTC
thermistors
Time tolerance
+100 %, -50 %
3TX4180-0A
Coupling links for control by PLC for 3TH4 contactor relays
Operating range: 17 to 30 V DC
Power consumption: 0.5 W at 24 V DC
3TX4090
mounted to contactor
For contactors
Type
Rated control
supply voltage Us
50/60 Hz AC
DC
V
V
OFF-delay
(minimum times)
DT Screw terminals
Article No.
s
Price
per PU
OFF-delay devices for contactors with DC operation
Bridging of voltage interruptions up to 1.2 sec
3TX4701-0AN1
3TH42..-0BF4
3TH43. .-0BF4
110
--
0.15 or 0.3
A
3TX4701-0AN1
1
1 unit
41B
3TH42..-0BM4
3TH43..-0BM4
220
--
0.6 or 1.2
A
3TX4701-0AN1
1
1 unit
41B
3TH42..-0BP4
3TH43..-0BP4
230
--
0.6 or 1.2
A
3TX4701-0AN1
1
1 unit
41B
3TH42..-0BB4
3TH43..-0BB4
--
24
0.4 or 0.8
B
3TX4701-0BB4
1
1 unit
41B
* You can order this quantity or a multiple thereof.
Illustrations are approximate
Siemens IC 10 · 2014
5/23
5
3TH42,
3TH43
© Siemens AG 2013
Contactor Relays
3TH2 contactor relays,
4- and 8-pole
■ Overview
■ Accessories
Standards
Auxiliary switch blocks
IEC 60947-1, EN 60947-1,
IEC 60947-5-1, EN 60947-5-1
The contactor relays with 4 contacts with screw terminals can be
expanded by up to 4 contacts by adding snap-on auxiliary
switch blocks (see "Accessories", page 5/30).
The 3TH2 contactor relays are suitable for use in any climate.
Contactor relays with screw terminal are finger-safe according to
EN 50274.
The terminal designations are according to EN 50011.
Connections
5
The 3TH20 contactor relays with 4 auxiliary contacts are available with SIGUT screw terminals, 6.3 mm x 0.8 mm flat connectors, and solder pin connections.
The contactor relays with 6.3 mm x 0.8 mm flat connectors can
be used in the plug-in base with solder pin connections for
printed circuit boards. The contactor relays are coded, and the
plug-in base is codable in order to ensure non-interchangeability.
The 3TH22 contactor relays with 8 integrated contacts are available with screw terminals. The terminal designations are according to EN 50011.
Contact reliability
High contact stability at low voltages and currents, particularly
suitable for solid-state circuits with currents  1 mA at a voltage
of  17 V.
3TH27 latched contactor relays
The contactor coil and the coil of the release solenoid are both
designed for uninterrupted duty.
RC elements, varistors, diodes or diode assemblies can be fitted
to both coils from the front for damping opening surges in the
coil.
The contactor relay can also be switched on and released
manually.
A cover (with unit labeling plate) must be removed from the front
of the contactor relay for this purpose. The auxiliary switch block
is then easy to mount. The auxiliary switch blocks can be removed again by unlocking them with a laterally arranged orange
slide.
The contactor relays with screw terminals with 4 contacts according to EN 50011 with the identification number 40E can be
expanded with 80E, 71E, 62E, 53E or 44E auxiliary switch blocks
to a total of 8 contacts according to EN 50011. The identification
numbers 80E, 71E, 62E, 53E or 44E on the coded auxiliary
switch blocks apply to the complete contactors. These auxiliary
switch blocks cannot be combined with contactor relays with
identification number 31E and 33E.
All contactor relays with screw terminals with 4 contacts according to EN 50011, identification number 40E, 31E or 22E, can be
expanded with auxiliary switch blocks with identification number
40, 31, 22, 20, 11 or 02 to a total of 6 or 8 contacts according to
EN 50005. The identification numbers on the auxiliary switch
blocks apply only to the attached auxiliary switch blocks.
Surge suppression
RC elements, varistors, diodes or diode assemblies (combination of a diode and a Zener diode for short break times) can be
plugged onto all contactors and auxiliary switch blocks with
screw terminals from the front in order to dampen opening
surges in the coil (see "Accessories", page 5/31).
The unit labeling plate must be removed for this purpose. It can
be snapped onto the attached surge suppressor.
Additional load module
The 3TX4490-1J additional load module (see "Accessories",
page 5/31) can be used by programmable logic controllers to increase permissible residual current, and to limit residual voltage
in semiconductor outputs.
This module ensures the safe shut-down of 3TH2 contactor relays and 3TF2 contactors with direct control via 230 V AC semiconductor outputs. It is accommodated in the same enclosure
as the 3TX4490-3. surge suppressors and can be plugged into
the contactor.
5/24
Siemens IC 10 · 2014
© Siemens AG 2013
Contactor Relays
3TH2 contactor relays,
4- and 8-pole
■ Technical specifications
Contactor relays
Type
3TH2
Contact endurance for AC-15/AC-14 and
DC-13 utilization categories
30
NSB0_00659
Million operating cycles (106)
Coupling links
10
5
3
2
1
0,5
Contactor relays
and coupling links
DC-13
220 V
DC-13
110 V
DC-13
24 V
AC-15/AC-14
0,1
0,05
0,01
0,01 0,03 0,05 0,1
0,3 0,5
1
2 3 4 5 7 10
a
5
The contact endurance is mainly dependent on the breaking
current. It is assumed that the operating mechanisms are
switched randomly, i.e. not synchronized with the phase angle
of the supply system.
If magnetic circuits other than the contactor coil systems or
solenoid valves are present, e.g. magnetic brakes, protective
measures for the load circuits are necessary. RC elements or
freewheel diodes are suitable as protective measures for the
circuits.
Legend for the diagram:
Ie = Rated operational current
Ia = Breaking current
(A)
-DC-13 e -DC-13 e-DC-13 e-AC-15/AC-14
110 V
24 V
≤ 230 V
220 V
e
Positively-driven operation of contacts in contactor relays
3TH20:
Yes, in the basic unit and the auxiliary switch block as well as between the
basic unit and the snap-on auxiliary switch block (removable) acc. to:
• ZH 1/457
• IEC 60947-5-1, Appendix L
3TH22:
Yes, in the basic unit and the auxiliary switch block as well as between the
basic unit and the snap-on auxiliary switch block (permanently mounted)
according to:
• ZH 1/457
• IEC 60947-5-1, Appendix L
• SUVA
Explanations:
There is positively-driven operation if it is ensured that the
NC and NO contacts cannot be closed at the same time.
ZH1/457
Safety rules for control units on power-operated presses in the
metal-working industry.
IEC 60947-5-1, Appendix L
Low-Voltage Switchgear and Controlgear, Control Circuit Devices and
Switching Elements.
Special requirements for positively-driven contacts
SUVA
Accident prevention regulations of the "Schweizer Unfallverhütungsanstalt"
(Swiss Institute for Accident Insurance)
Contactor relays
Dimensions (W x H x D)
• With 3TX4 490 surge suppressor
W
D
H
Type
Auxiliary switch block
3TH20..-....
3TH22..-....
3TX4...-..
mm
45 x 48 x 63
45 x 48 x 91
45 x 33 x 28
mm
45 x 48 x 88
45 x 48 x 116
--
General technical specifications
Permissible mounting position
AC and DC operation
Mechanical endurance
• AC operation
• DC operation
Any
Operating 10 million
cycles
30 million
Rated insulation voltage Ui
(pollution degree 3)
• Screw terminals
• Flat connectors 6.3 mm x 0.8 mm
• Solder pin connections
V
V
V
690
500
500
500
---
500
---
Rated impulse withstand voltage Uimp
(pollution degree 3)
• Screw terminals
• Flat connectors 6.3 mm x 0.8 mm
• Solder pin connections
kV
kV
kV
6
6
6
6
---
6
---
V
Up to 300
°C
°C
-25 ... +55
-55 ... +80
Protective separation between coil and contacts
(according to IEC 60947-1, Appendix N)
Permissible ambient temperature
1)
• During operation
• During storage
Degree of protection acc. to IEC 60947-1 Appendix C
IP00/open
• Connection range for screw terminals
IP20
Touch protection acc. to EN 50274
Finger-safe for screw terminals
Shock resistance
• Rectangular pulse
- AC operation
- DC operation
g/ms
g/ms
7/5 and 4/10
10/5 and 6/10
• Sine pulse
- AC operation
- DC operation
g/ms
g/ms
9/5 and 6/10
13/5 and 8/10
2)
Conductor cross-sections
1)
Applies to 50/60 Hz coil:
Operating range at 60 Hz: 0.85 ... 1.1 x Us;
at 50 Hz, 1.1 x Us, side-by-side mounting and 100 % ON-period,
the maximum ambient temperature is +40 °C.
2)
Conductor cross-sections, see page 5/26.
Siemens IC 10 · 2014
5/25
© Siemens AG 2013
Contactor Relays
3TH2 contactor relays,
4- and 8-pole
Contactor relays
Type
3TH2
Short-circuit protection
Short-circuit test
with fuse links of operational class gG
with short-circuit current Ik = 1 kA acc. to IEC 60947-5-1
LV HRC, type 3NA; DIAZED, type 5SB; NEOZED, type 5SE
A
6
Conductor cross-sections
Main and auxiliary conductors
Screw terminals
mm2
mm2
• Solid or stranded
• Finely stranded with end sleeve
• Terminal screw
2 x (0.5 ... 2.5)
2 x (0.5 ... 1.5)
M3
Flat connectors
• Finely stranded
When using a plug-in sleeve
- 6.3 ... 1
- 6,3 ... 2.5
mm2
mm2
0.5 ... 1
1 ... 2.5
5
Solder pin connections
(only for printed circuit boards)
• Solder pin cross-section
(does not apply to plug-in
bases)
mm2
0.8 x 1.2
Control circuit
Solenoid coil operating range1)
0.8 ... 1.1 x Us
Power consumption of the solenoid coils
(for cold coil and 1.0 x Us)
• AC operation, 50 Hz
• AC operation, 60 Hz
• AC operation, 50/60 Hz1)
• DC operation
Closing
P.f.
Closed
P.f.
Closing
P.f.
Closed
P.f.
Closing
P.f.
Closed
P.f.
Closing = Closed
Permissible residual current of the electronics (with 0 signal)
AC operation
DC operation
VA
VA
VA
VA
VA
VA
15
0.41
6.8
0.42
14.4
0.36
6.1
0.46
16.5/13.2
0.43/0.38
8.0/5.4
0.48/0.42
W
3
mA
mA
 3 x (220 V/Us)
 1 x (220 V/Us)
Operating times for 0.8 ... 1.1 x Us2)
Total break time = Opening delay + Arcing time
Values apply with coil in cold state and at operating temperature for
operating range
• AC operation
- Closing
ON-delay NO
OFF-delay NC
ms
ms
5 ... 20
4 ... 12
- Opening
OFF-delay NO
ON-delay NC
ms
ms
3 ... 24
3 ... 20
- Closing
ON-delay NO
OFF-delay NC
ms
ms
16 ... 140
13 ... 40
- Opening
OFF-delay NO
ON-delay NC
ms
ms
3 ... 6
4 ... 10
ms
10
• DC operation
• Arcing time
Operating times for 1.0 x Us2)
• AC operation
- Closing
ON-delay NO
OFF-delay NC
ms
ms
6 ... 17
5 ... 12
- Opening
OFF-delay NO
ON-delay NC
ms
ms
3 ... 24
5 ... 20
- Closing
ON-delay NO
OFF-delay NC
ms
ms
18 ... 42
15 ... 26
- Opening
OFF-delay NO
ON-delay NC
ms
ms
3 ... 5
4 ... 10
• DC operation
1)
Applies to 50/60 Hz coil
Operating range at 60 Hz: 0.85 ... 1.1 x Us;
at 50 Hz, 1.1 x Us, side-by-side mounting and 100 % ON-period,
the maximum ambient temperature is +40 °C.
5/26
Siemens IC 10 · 2014
2)
The OFF-delay of the NO contact and the ON-delay of the NC contact are
increased if the contactor coils are attenuated against voltage peaks
(noise suppression diode 6 to 10 times; diode assembly 2 to 6 times,
varistor +2 to 5 ms).
© Siemens AG 2013
Contactor Relays
3TH2 contactor relays,
4- and 8-pole
Contactor relays
Type
3TH2
Load side
Load rating with AC
Utilization category AC-12
Rated operational current Ie (at 60 °C)
A
10
230/220 V
400/380 V
500 V
690/660 V
A
A
A
A
4
3
2
1
110 V
230/220 V
400/380 V
500 V
690/660 V
kW
kW
kW
kW
kW
0.2
0.55
1.1
1.5
1.5
A
10
Utilization categories AC-15 and AC-14
Rated power of three-phase motors
Acc. to utilization category
AC-2 and AC-3
5
Rated operational current Ie
For rated operational voltage Ue
Load rating with DC
Utilization category DC-12
Rated operational current Ie
For rated operational voltage Ue
• 1 conducting path1)
Up to 24 V
60 V
110 V
240/220 V
A
A
A
A
4
2
1.1
0.5
• 2 conducting paths in series
Up to 24 V
60 V
110 V
240/220 V
A
A
A
A
10
10
4
2
• 3 conducting paths in series
Up to 24 V
60 V
110 V
240/220 V
A
A
A
A
10
10
6
2.5
• 1 conducting path
Up to 24 V
60 V
110 V
240/220 V
A
A
A
A
2.1
0.9
0.52
0.27
• 2 conducting paths in series
Up to 24 V
60 V
110 V
240/220 V
A
A
A
A
10
3.5
1.3
0.9
• 3 conducting paths in series
Up to 24 V
60 V
110 V
240/220 V
A
A
A
A
10
4.7
3
1.2
AC-12/DC-12
h-1
1 000
AC-2
AC-3
AC-15/AC-14
DC-13
h-1
h-1
h-1
h-1
h-1
500
1 000
1 200
1 200
1 0000
Utilization category DC-13
Rated operational current Ie
For rated operational voltage Ue
Switching frequency
Switching frequency z in operating cycles/hour
Rated operation for utilization category
Dependence of the switching frequency z'
on the operational current I' and
operational voltage U'
z’ = z (Ie/I ’) (400 V/U ’)1.5 1/h
No-load switching frequency
1)
Contact endurance 0.1 x 106 operating cycles.
Siemens IC 10 · 2014
5/27
© Siemens AG 2013
Contactor Relays
3TH2 contactor relays,
4- and 8-pole
■ Selection and ordering data
Contacts Rated operational current
Ie/AC-15/AC-14
at
Contacts
230/
400/
220 V 380 V
Ident. No.
acc. to
EN 50011
Number
A
A
500 V
690/
660 V
A
A
DT Screw terminals
Version
NO
Article No.
PU
(UNIT,
SET,
M)
PS*
PG
Price
per PU
NC
For screw fixing and snap-on mounting onto TH 35 standard mounting rail
Terminal designations according to EN 50011
5
4 NO, Ident. No. 40E
2 NO + 2 NC, Ident. No. 22E
3 NO + 1 NC, Ident. No. 31E
A1(+) 13 23 33 43
A1(+) 13 21 33 43
A1(+) 13 21 31 43
A2( ) 14 24 34 44
A2(–) 14 22 34 44
A2(–) 14 22 32 44
AC operation
4
4
3
2
1
40E
31E
22E
4
3
2
-1
2
A
A
A
3TH2040-0AP0
3TH2031-0AP0
3TH2022-0AP0
1
1
1
1 unit
1 unit
1 unit
41A
41A
41A
3
2
1
40E
31E
22E
4
3
2
-1
2
A
A
A
3TH2040-0BB4
3TH2031-0BB4
3TH2022-0BB4
1
1
1
1 unit
1 unit
1 unit
41A
41A
41A
DC operation
4
4
3TH20. .-0A. .
With permanently mounted auxiliary switch blocks 
For screw fixing and snap-on mounting onto TH 35 standard mounting rail
Terminal designations according to EN 50011
8 NO, Ident. No. 80E
6 NO + 2 NC, Ident. No. 62E
7 NO + 1 NC, Ident. No. 71E
A1(+) 13 23 33 43 53 63 73 83
A2( ) 14 24 34 44 54 64 74 84
5 NO + 3 NC, Ident. No. 53E
A1(+) 13 23 33 43 53 61 73 83
A1(+) 13 23 33 43 53 61 71 83
A2(–) 14 24 34 44 54 62 74 84
A2(–) 14 24 34 44 54 62 72 84
4 NO + 4 NC, Ident. No. 44E
A1(+) 13 23 33 43 53 61 71 81
A1(+) 13 23 33 43 51 61 71 81
A2(–) 14 24 34 44 54 62 72 82
A2(–) 14 24 34 44 52 62 72 82
AC operation
8
3TH22. .-0A. .
4
3
2
--
80E
71E
62E
8
7
6
0
1
2
C
C
C
3TH2280-0AP0
3TH2271-0AP0
3TH2262-0AP0
1
1
1
1 unit
1 unit
1 unit
41A
41A
41A
53E
44E
5
4
3
4
C
C
3TH2253-0AP0
3TH2244-0AP0
1
1
1 unit
1 unit
41A
41A
80E
71E
62E
8
7
6
0
1
2
C
C
C
3TH2280-0BB4
3TH2271-0BB4
3TH2262-0BB4
1
1
1
1 unit
1 unit
1 unit
41A
41A
41A
53E
44E
5
4
3
4
C
C
3TH2253-0BB4
3TH2244-0BB4
1
1
1 unit
1 unit
41A
41A
DC operation
8
4
3
2
--
Latched contactor relays 
For screw fixing and snap-on mounting onto TH 35 standard mounting rail
Terminal designations according to EN 50011
4 NO, Ident. No. 40E
2 NO + 2 NC, Ident. No. 22E
3 NO + 1 NC, Ident. No. 31E
E1(+) A1+
( ) 13 23 33 43
E1(+) A1(+) 13 21 33 43
E1(+) A1(+) 13 21 31 43
E2(-) A2(-) 14 24 34 44
E2(–) A2(–) 14 22 34 44
E2(–) A2(–) 14 22 32 44
AC operation
4
4
3
2
1
40E
31E
22E
4
3
2
-1
2
C
C
C
3TH2740-0AP0
3TH2731-0AP0
3TH2722-0AP0
1
1
1
1 unit
1 unit
1 unit
41A
41A
41A
3
2
1
40E
31E
22E
4
3
2
-1
2
C
C
C
3TH2740-0BB4
3TH2731-0BB4
3TH2722-0BB4
1
1
1
1 unit
1 unit
1 unit
41A
41A
41A
DC operation
4
4
3TH27..
Accessories see pages 5/30 and 5/31.
5/28
Siemens IC 10 · 2014
* You can order this quantity or a multiple thereof.
Illustrations are approximate
© Siemens AG 2013
Contactor Relays
3TH2 contactor relays,
4- and 8-pole
Contacts Rated operational current
Ie/AC-15/AC-14 at
Contacts
230/
400/
220 V 380 V
Ident. No.
acc. to
EN 50011
Number
A
A
500 V
690/
660 V
A
A
DT Flat connectors
Version
NO
Article No.
Price
per PU
PU
(UNIT,
SET,
M)
PS*
PG
NC
Contactor relays with 6.3 mm x 0.8 mm flat connectors
Terminal designations according to EN 50011
4 NO, Ident. No. 40E
A1(+)
A2( )
2 NO + 2 NC, Ident. No. 22E
3 NO + 1 NC, Ident. No. 31E
13 23 33 43
A1(+)
A2( )
14 24 34 44
13 21 33 43
A1(+)
A2( )
14 22 34 44
13 21 31 43
14 22 32 44
AC operation
4
3TH20. .-3. . .
3
4
5
For screw fixing and snap-on mounting onto TH 35 standard mounting
rail
2
--
40E
31E
22E
4
3
2
-1
2
C
D
C
3TH2040-3AP0
3TH2031-3AP0
3TH2022-3AP0
1
1
1
1 unit
1 unit
1 unit
41A
41A
41A
2
--
40E
31E
22E
4
3
2
-1
2
C
C
C
3TH2040-7AP0
3TH2031-7AP0
3TH2022-7AP0
1
1
1
1 unit
1 unit
1 unit
41A
41A
41A
For screw fixing (diagonal)
4
3
4
DC operation
For screw fixing and snap-on mounting onto TH 35 standard mounting
rail
4
3TH20. .-7. . .
3
4
2
--
40E
31E
22E
4
3
2
-1
2
C
C
D
3TH2040-3BB4
3TH2031-3BB4
3TH2022-3BB4
1
1
1
1 unit
1 unit
1 unit
41A
41A
41A
2
--
40E
31E
22E
4
3
2
-1
2
D
C
C
3TH2040-7BB4
3TH2031-7BB4
3TH2022-7BB4
1
1
1
1 unit
1 unit
1 unit
41A
41A
41A
For screw fixing (diagonal)
4
3
4
Contactor relays with solder pin connections for printed circuit boards
Terminal designations according to EN 50011
4 NO, Ident. No. 40E
A1(+)
A2( )
Solder pin
connections
3 NO + 1 NC, Ident. No. 31E
13 23 33 43
A1(+)
A2( )
14 24 34 44
2 NO + 2 NC, Ident. No. 22E
13 21 33 43
A1(+)
A2( )
14 22 34 44
13 21 31 43
14 22 32 44
AC operation
For screw fixing (diagonal)
4
3
4
2
--
40E
31E
22E
4
3
2
-1
2
C
C
D
3TH2040-6AP0
3TH2031-6AP0
3TH2022-6AP0
1
1
1
1 unit
1 unit
1 unit
41A
41A
41A
2
--
40E
31E
22E
4
3
2
-1
2
C
C
D
3TH2040-6BB4
3TH2031-6BB4
3TH2022-6BB4
1
1
1
1 unit
1 unit
1 unit
41A
41A
41A
DC operation
3TH20. .-6. . .
For screw fixing (diagonal)
4
4
3
Accessories see pages 5/30 and 5/31.
■ Options
Rated control supply voltages (change of 10th and 11th digit of the Article No.)
Contactor type
3TH20..-0...
Rated control supply voltage Us
3TH20..-3...,
3TH20..-6...,
3TH20..-7...,
3TH22, 3TH27
AC operation
Contactor type
3TH20..-0...
3TH20..-3...,
3TH20..-6...,
3TH20..-7...,
3TH22, 3TH27
B4
F4
M4
B4
---
Rated control supply voltage Us
DC operation
Solenoid coils for AC 50 and 60 Hz
50 Hz
60 Hz
24 V AC
110 V AC
230/220 V AC
29 V AC
132 V AC
276 V AC
B0
F0
P01)
--P01)
24 V DC
110 V DC
220 V DC
1)
Operating range at 220 V or 380 V:
0.85 to 1.15 x Us; lower operating range limit according to IEC 60947.
Please inquire about further voltages.
* You can order this quantity or a multiple thereof.
Illustrations are approximate
Siemens IC 10 · 2014
5/29
© Siemens AG 2013
Contactor Relays
3TH2 contactor relays,
4- and 8-pole
■ Accessories
Rated operational
current
Ie/AC-15/AC-14 at
Contacts
DT Screw terminals
230/ 400/
500 V Ident. No. Version
220 V 380 V
A
A
A
NO NC
Article No.
PU
(UNIT,
SET,
M)
PS*
PG
Price
per PU
NO NC
Snap-on auxiliary switch blocks for 3TH20 contactor relays
For expansion to 8 contacts according to EN 50011
Only for 3TH2040-0... (with 4 NO, Ident. No. 40E)
4
3
2
5
3TX4440-0A
80E
71E
62E
53E
44E
4
3
2
1
--
-1
2
3
4
------
------
}
}
}
}
}
3TX4440-0A
3TX4431-0A
3TX4422-0A
3TX4413-0A
3TX4404-0A
1
1
1
1
1
1 unit
1 unit
1 unit
1 unit
1 unit
41A
41A
41A
41A
41A
For expansion to 6 or 8 contacts according to EN 50005
4
3
2
40E
4
--
--
--
53 63 73 83
}
3TX4440-2A
1
1 unit
41A
31E
3
1
--
--
54 64 74 84
53 61 73 83
}
3TX4431-2A
1
1 unit
41A
22E
2
2
--
--
54 62 74 84
53 61 71 83
}
3TX4422-2A
1
1 unit
41A
22; 2U
--
--
2
2
54 62 72 84
57 67 75 85
B
3TX4422-2G
1
1 unit
41A
20E
2
--
--
--
53 63
}
3TX4420-2A
1
1 unit
41A
11E
1
1
--
--
54 64
53 61
}
3TX4411-2A
1
1 unit
41A
02E
--
2
--
--
51 61
}
3TX4402-2A
1
1 unit
41A
11; U
--
--
1
1
52 62
57 65
D
3TX4411-2G
1
1 unit
41A
PU
(UNIT,
SET,
M)
PS*
PG
58 68 76 86
4
3
2
54 62
58 66
For contactors
Type
Rated control supply voltage Us OFF-delay
(minimum times)
50/60 Hz AC
DC
V
V
DT Screw terminals
Article No.
Price
per PU
s
OFF-delay devices for contactors with DC operation
Bridging of voltage interruptions up to 0.8 sec
3TH2. . .-0BB4
--
24
0.25 or 0.5
A
3TX4490-1H
1
1 unit
41B
3TH2. . .-0BF4
110
--
0.1 or 0.2
A
3TX4490-1A
1
1 unit
41B
3TH2. . .-0BM4,
3TH2. . .-0BP4
220/230
--
0.4 or 0.8
A
3TX4490-1A
1
1 unit
41B
3TX4490-1A
5/30
Siemens IC 10 · 2014
* You can order this quantity or a multiple thereof.
Illustrations are approximate
© Siemens AG 2013
Contactor Relays
3TH2 contactor relays,
4- and 8-pole
For contactors
Rated control
supply voltage Us
Power consumption
of LED at Us
Type
V AC
mW
V DC
DT Article No.
Price
per PU
PU
(UNIT,
SET,
M)
PS*
PG
Surge suppressors1)
for plugging onto contactors with and without auxiliary switch blocks
Version without LED
RC elements
3TH2. . .-0. . .
3TX4490-3A
24 ... 48
48 ... 127
127 ... 240
24 ... 70
70 ... 150
150 ... 250
----
B
B
B
3TX4490-3R
3TX4490-3S
3TX4490-3T
1
1
1
1 unit
1 unit
1 unit
41B
41B
41B
240 ... 400
400 ... 600
---
---
B
B
3TX4490-3U
3TX4490-3V
1
1
1 unit
1 unit
41B
41B
 48
48 ... 127
127 ... 240
24 ... 70
70 ... 150
150 ... 250
----
}
B
B
3TX4490-3G
3TX4490-3H
3TX4490-3J
1
1
1
1 unit
1 unit
1 unit
41B
41B
41B
240 ... 400
400 ... 600
---
---
B
B
3TX4490-3K
3TX4490-3L
1 10 units
1 10 units
41B
41B
12 ... 250
--
}
3TX4490-3A
1
1 unit
41B
24 ... 250
--
B
3TX4490-3B
1
1 unit
41B
12 ... 24
24 ... 70
70 ... 150
150 ... 250
10 ... 120
20 ... 470
50 ... 700
160 ... 950
B
B
B
D
3TX4490-4G
3TX4490-4H
3TX4490-4J
3TX4490-4K
1
1
1
1
1 unit
1 unit
1 unit
1 unit
41B
41B
41B
41B
24 ... 70
70 ... 150
150 ... 250
20 ... 470
50 ... 700
160 ... 950
B
B
B
3TX4490-4A
3TX4490-4B
3TX4490-4C
1
1
1
1 unit
1 unit
1 unit
41B
41B
41B
D
3TX4490-1J
1
1 unit
41B
D
3TX4491-2A
1
5 units
41A
D
3TX4491-2K
1
1 unit
41A
Noise suppression diodes
3TH2. . .-0. . .
--
Diode assemblies (diode and Zener diode)
For DC operation and short break times
3TH2. . .-0. . .
--
Version with LED
Varistors
3TH2. . .-0. . .
24 ... 48
48 ... 127
127 ... 240
--
3TX4490-4G
Noise suppression diodes
3TH2. . .-0. . .
----
Additional load modules for 3TH2 contactor relays
for plugging onto contactors with and without auxiliary switch blocks
For increasing the permissible residual current and for limiting the
residual voltage of SIMATIC semiconductor outputs
3TH2. . .-0A. .
3TX4490-1J
230/220, 50 Hz
-230, 60 Hz
-230, 50/60 Hz
-Operating range 0.8 ... 1.1 × Us
Plug-in bases with solder pin connections for printed circuit boards,
width 45 mm
For 3TH2 contactor relays;
with flat connectors 1 x 6.3 mm ... 0.8 mm
Rated insulation voltage Ui: 400 V (at pollution degree 3);
rated impulse withstand voltage Uimp: 6 kV;
rated operational current Ie: 6 A;
s and U rated data: max. 300 V, 6 A
3TX4491-2A
3TH20. .-3. . .,
3TH20. .-7. . .
Release tools
3TH20. .-7. . .
1)
For releasing contactors from
3TX4491-2A plug-in bases
The OFF-delay of the NO contact and the ON-delay of the NC contact are
increased if the contactor coils are attenuated against voltage peaks
(noise suppression diode 6 to 10 times;
diode assembly 2 to 6 times, varistor +2 to 5 ms).
* You can order this quantity or a multiple thereof.
Illustrations are approximate
Siemens IC 10 · 2014
5/31
5
Varistors
3TH2. . .-0. . .
© Siemens AG 2013
Contactor Relays
Coupling Contactors
SIRIUS 3RH21 coupling contactors
for switching auxiliary circuits, 4-pole
■ Overview
The 3RH21 coupling contactors cannot be extended with
auxiliary switch blocks.
DC operation
IEC 60947-1, EN 60947-1,
IEC 60947-5-1, EN 60947-5-1
The 3RH21 coupling contactors for switching auxiliary circuits
are tailored to the special requirements of working with electronic controls.
Coupling contactors have a low power consumption and an
extended solenoid coil operating range.
Depending on the version, solenoid coils are supplied either
without overvoltage damping (versions 3RH21 . .-.HB40 or
3RH21 . .-.MB40-0KT0) or with a diode or suppressor diode
connected as standard.
■ Technical specifications
5
All technical specifications not mentioned in the table below
are identical to those of the 3RH21 contactor contactors
(see page 5/6).
Contactor type
3RH21. .-.HB40
3RH21. .-.JB40
3RH21. .-.KB40
Size
S00
S00
S00
With diode
With suppressor diode
38 ... 65
55 ... 75
7 ... 20
20 ... 30
Control circuit
0.7 ... 1.25 x Us
Solenoid coil operating range
Power consumption of the solenoid coil
(for cold coil)
Closing = Closed
• At Us = 17 V
W
1.4
• At Us = 24 V
• At Us = 30 V
W
2.8
W
4.4
Permissible residual current
of the electronics for 0 signal
< 10 mA x (24 V/Us)
Overvoltage configuration of the solenoid coil
No overvoltage damping
Operating times
• Closing at 17 V
- ON-delay NO
- OFF-delay NC
ms
ms
40 ... 130
30 ... 80
• At 24 V
- ON-delay NO
- OFF-delay NC
ms
ms
35 ... 60
25 ... 40
• At 30 V
- ON-delay NO
- OFF-delay NC
ms
ms
25 ... 50
15 ... 30
• Closing at 17 ... 30 V
- OFF-delay NO
- ON-delay NC
ms
ms
7 ... 20
20 ... 30
Upright mounting position
On request
Contactor type
3RH21. .-.MB40-0KT0
3RH21. .-.VB40
3RH21. .-.WB40
Size
S00
S00
S00
Control circuit
0.85 ... 1.85 x Us
Solenoid coil operating range
Power consumption of the solenoid coil
(for cold coil)
Closing = Closed at Us = 24 V
W
1.6
Permissible residual current
of the electronics for 0 signal
< 8 mA x (24 V/Us)
Overvoltage configuration of the solenoid coil
Diode, varistor or RC element, Built-in diode
attachable
5/32
Siemens IC 10 · 2014
Built-in suppressor diode
© Siemens AG 2013
Contactor Relays
Coupling Contactors
SIRIUS 3RH21 coupling contactors
for switching auxiliary circuits, 4-pole
Contactor type
3RH21. .-.MB40-0KT0
3RH21. .-.VB40
3RH21. .-.WB40
Size
S00
S00
S00
20 ... 80
30 ... 90
5 ... 20
10 ... 30
Control circuit
Operating times
• Closing at 20.5 V
- ON-delay NO
- OFF-delay NC
ms
ms
30 ... 120
20 ... 110
• At 24 V
- ON-delay NO
- OFF-delay NC
ms
ms
25 ... 90
15 ... 80
• At 44 V
- ON-delay NO
- OFF-delay NC
ms
ms
15 ... 60
10 ... 50
• Closing at 17 ... 30 V
- OFF-delay NO
- ON-delay NC
ms
ms
5 ... 20
10 ... 30
On request
5
Upright mounting position
■ Selection and ordering data
DC operation
Low power consumption
Extended operating range of the solenoid coil
Integrated coil circuit
PU (UNIT, SET, M) = 1
PS*
= 1 unit
PG
= 41A
3RH21. .-1.B40
Rated operational current
Ie/AC-15/ AC-14
at 230 V
Auxiliary contacts
Ident. No. acc. to
EN 50011
DT Screw terminals
DT Spring-type terminals
Version
Article No.
NO
A
3RH21. .-2.B40
Price
per PU
Article No.
Price
per PU
NC
For screw fixing and snap-on mounting onto
TH 35 standard mounting rail
Size S00
Diode, varistor or RC element, attachable
Terminal designations according to EN 50011 (auxiliary switch blocks cannot be mounted)
4 NO, Ident. No. 40E
A1(+)
A2(–)
3 NO + 1 NC, Ident. No. 31E
13 23 33 43
13 21 33 43
A1(+)
A2(–)
14 22 34 44
14 24 34 44
2 NO + 2 NC, Ident. No. 22E
A1(+)
13 21 31 43
A2(–)
14 22 32 44
Rated control supply voltage Us = 24 V DC,
operating range 0.7 to 1.25 x Us
Power consumption of the solenoid coils 2.8 W at 24 V
10
40E
31E
22E
4
3
2
-1
2
B
B
B
3RH2140-1HB40
3RH2131-1HB40
3RH2122-1HB40
B
B
B
3RH2140-2HB40
3RH2131-2HB40
3RH2122-2HB40
-1
2
B
B
B
3RH2140-1MB40-0KT0
3RH2131-1MB40-0KT0
3RH2122-1MB40-0KT0
B
B
B
3RH2140-2MB40-0KT0
3RH2131-2MB40-0KT0
3RH2122-2MB40-0KT0
Rated control supply voltage Us = 24 V DC,
operating range 0.85 to 1.85 x Us
Power consumption of the solenoid coils 1.6 W at 24 V
10
40E
31E
22E
4
3
2
For surge suppressors, see page 5/13.
* You can order this quantity or a multiple thereof.
Illustrations are approximate
Siemens IC 10 · 2014
5/33
© Siemens AG 2013
Contactor Relays
Coupling Contactors
SIRIUS 3RH21 coupling contactors
for switching auxiliary circuits, 4-pole
PU (UNIT, SET, M) = 1
PS*
= 1 unit
PG
= 41A
3RH21. .-1.B40
Auxiliary contacts
Ident. No. acc. to
EN 50011
3RH21. .-2.B40
DT Screw terminals
DT Spring-type terminals
Version
Article No.
Price
per PU
Article No.
Price
per PU
5
Rated operational current
Ie/AC-15/ AC-14
at 230 V
NO
A
NC
For screw fixing and snap-on mounting onto
TH 35 standard mounting rail
Size S00
With integrated coil circuit (diode)
Terminal designations according to EN 50011 (auxiliary switch blocks cannot be mounted)
4 NO, Ident. No. 40E
A1(+)
A2(–)
3 NO + 1 NC, Ident. No. 31E
13 23 33 43
13 21 33 43
A1(+)
A2(–)
14 24 34 44
2 NO + 2 NC, Ident. No. 22E
A1(+)
13 21 31 43
A2(–)
14 22 34 44
14 22 32 44
Rated control supply voltage Us = 24 V DC,
operating range 0.7 to 1.25 x Us
Power consumption of the solenoid coils 2.8 W at 24 V
10
40E
31E
22E
4
3
2
-1
2
B
}
}
3RH2140-1JB40
3RH2131-1JB40
3RH2122-1JB40
B
}
B
3RH2140-2JB40
3RH2131-2JB40
3RH2122-2JB40
-1
2
B
B
B
3RH2140-1VB40
3RH2131-1VB40
3RH2122-1VB40
B
B
B
3RH2140-2VB40
3RH2131-2VB40
3RH2122-2VB40
Rated control supply voltage Us = 24 V DC,
operating range 0.85 to 1.85 x Us
Power consumption of the solenoid coils 1.6 W at 24 V
10
40E
31E
22E
4
3
2
With integrated coil circuit (suppressor diode)
Terminal designations according to EN 50011 (auxiliary switch blocks cannot be mounted)
4 NO, Ident. No. 40E
A1(+)
A2(–)
3 NO + 1 NC, Ident. No. 31E
13 23 33 43
13 21 33 43
A1(+)
A2(–)
14 24 34 44
2 NO + 2 NC, Ident. No. 22E
A1(+)
A2(–)
14 22 34 44
13 21 31 43
14 22 32 44
Rated control supply voltage Us = 24 V DC,
operating range 0.7 to 1.25 x Us
Power consumption of the solenoid coils 2.8 W at 24 V
10
40E
31E
22E
4
3
2
-1
2
B
}
}
3RH2140-1KB40
3RH2131-1KB40
3RH2122-1KB40
B
}
}
3RH2140-2KB40
3RH2131-2KB40
3RH2122-2KB40
-1
2
B
B
B
3RH2140-1SB40
3RH2131-1SB40
3RH2122-1SB40
B
B
B
3RH2140-2SB40
3RH2131-2SB40
3RH2122-2SB40
Rated control supply voltage Us = 24 V DC,
operating range 0.85 to 1.85 x Us
Power consumption of the solenoid coils 1.6 W at 24 V
10
5/34
40E
31E
22E
Siemens IC 10 · 2014
4
3
2
* You can order this quantity or a multiple thereof.
Illustrations are approximate
© Siemens AG 2013
Contactor Relays
Contactors with Extended Operating Range 0.7 ... 1.25 x Us for Railway Applications
SIRIUS 3RH21 contactor relays
Note:
■ Overview
An additional auxiliary switch block cannot be mounted.
DC operation
Side-by-side mounting
IEC 60947-4-1, EN 60947-4-1
A clearance of 10 mm is required for side-by-side mounting at
ambient temperatures > 60 °C  70 °C.
The contactor relays are finger-safe according to EN 50274. The
size S00 contactor relays have spring-type connections for all
terminals.
Contactor relays with series resistor
Ambient temperature
Control and auxiliary circuits
The permissible ambient temperature for operation of the
contactor relays (across the full solenoid coil operating range) is
-40 to +70 °C.
The DC solenoid systems of the contactor relays are modified
(to holding excitation) by means of a series resistor.
The size S00 contactor relays are supplied prewired with a plugon module containing the series resistor. A surge suppressor
(a suppressor diode or varistor as preferred) is integrated.
Uninterrupted duty at temperatures > +60 °C reduces the
mechanical endurance, the current carrying capacity of the
conducting paths and the switching frequency.
The solenoid coils of the contactor relays have an extended coil
operating range from 0.7 to 1.25 x Us and are fitted as standard
with surge suppressors. The opening delay is consequently
2 to 5 ms longer than for standard contactors.
5
L+
L-
Control and auxiliary circuits
S1
E1+
For operation in installations which are subject both to considerable variations in the control voltage and to high ambient temperatures, e.g. railway applications under extreme climatic conditions, rolling mills, etc.
K1
K1
A2-
13 23 31
14 24 32
Also for control supply voltages with battery buffering to extend
the operating time in the event of battery charge failure.
NSB0_02177
■ Application
RV
Contactor relays with conventional coil
Circuit diagram (version with suppressor diode)
Control and auxiliary circuits
A 4-pole auxiliary switch block (according to EN 50005) can be
fitted additionally.
These contactor relays have an extended operating range from
0.7 to 1.25 x Us; the solenoid coils are fitted as standard with a
suppressor diode. An additional series resistor is not required.
Side-by-side mounting
Side-by-side-side mounting is permissible at ambient temperatures up to 70 °C.
■ Technical specifications
Contactor relays
Type
3RH21..
General technical specifications
Upright mounting position
• Contactors with series resistor
Special version (on request)
• Contactors with conventional coil
Special version (on request)
Ambient temperature
• During operation
°C
-40 ... +701)
• During storage
°C
-55 ... +80
Control circuit
Solenoid coil operating range
DC
0.7 ... 1.25 x Us
For cold coil and 1.0 x Us
Power consumption of the solenoid coils
• Contactors with series resistor
- Closing
- Closed
W
W
13
4
• Contactors with conventional coil
- Closing
- Closed
W
W
2.8
2.8
All details and technical specifications not mentioned here are
identical to those of the standard versions; see page 5/4.
1)
3RH21..-.K contactor relays without the suffix -0LA0 are coupling contactor
relays that are certified for the temperature range -25 °C to +60 °C.
For railway applications, an additional certification approves these contactors with a minimum distance of 10 mm for the extended temperature
range -40 °C to +70 °C.
Siemens IC 10 · 2014
5/35
© Siemens AG 2013
Contactor Relays
Contactors with Extended Operating Range 0.7 ... 1.25 x Us for Railway Applications
SIRIUS 3RH21 contactor relays
■ Selection and ordering data
DC operation
Spring-type terminals
For screw and snap-on mounting onto standard mounting rails
Solenoid coil with surge suppression
5
3RH2122-2K.40
Rated operational current
Ie/AC-15/AC-14
Tu: 70 °C at
230 V
400 V
500 V
Contacts
690 V
Rated control supply
voltage Us
3RH2122-2K.40-0LA0
DT Spring-type terminals
A
A
A
PS*
PG
Version
Article No.
A
PU
(UNIT,
SET, M)
NO
NC
Price
per PU
V DC
3RH21 contactor relays
Size S00
With conventional coil, fitted with suppressor diode
Terminal designations according to EN 50011
2 NO + 2 NC, Ident. No. 22E
A1(+)
A2(–)
3
10
3 NO + 1 NC, Ident. No. 31E
13 21 31 43
A1(+)
A2(–)
14 22 32 44
2
1
2
1)
24
110
3
1
1)
4
01)
21)
2
4 NO, Ident. No. 40E
13 21 33 43
A1(+)
A2(–)
14 22 34 44
13 23 33 43
14 24 34 44
}
A
3RH2122-2KB40
3RH2122-2KF40
1
1
1 unit
1 unit
41A
41A
24
}
3RH2131-2KB40
1
1 unit
41A
24
B
3RH2140-2KB40
1
1 unit
41A
24
110
B
B
3RH2122-2LB40
3RH2122-2LF40
1
1
1 unit
1 unit
41A
41A
12)
24
110
B
B
3RH2122-2KB40-0LA0
3RH2122-2KF40-0LA0
1
1
1 unit
1 unit
41A
41A
12)
24
110
B
B
3RH2122-2LB40-0LA0
3RH2122-2LF40-0LA0
1
1
1 unit
1 unit
41A
41A
With conventional coil, fitted with varistor
Terminal designations according to EN 50011
2 NO + 2 NC, Ident. No. 22E
A1(+)
A2(–)
3
10
13 21 31 43
14 22 32 44
2
1
2
With series resistor, fitted with suppressor diode
Terminal designations according to EN 50011
2 NO + 1 NC, Ident. No. 21X
E1(+)
A2(–)
10
13 23 31
14 24 32
3
2
1
2
With series resistor, fitted with varistor
Terminal designations according to EN 50011
2 NO + 1 NC, Ident. No. 21X
E1(+)
A2(–)
10
1)
2)
3
13 23 31
14 24 32
2
1
2
It is not possible to mount an auxiliary switch block.
4-pole auxiliary switch block according to EN 50005 can be mounted.
5/36
Siemens IC 10 · 2014
* You can order this quantity or a multiple thereof.
Illustrations are approximate
© Siemens AG 2013
Contactor Relays
Contactors with Extended Operating Range 0.7 ... 1.25 x Us for Railway Applications
3TH4 contactor relays
■ Overview
■ Application
For operation in plants which are subject both to considerable
variations in the control voltage and to high ambient temperatures, e.g. in railway applications.
Standards
IEC 60947-4-1, EN 60947-4-1
The contactor relays are finger-safe according to EN 50274.
Terminal covers may have to be fitted onto the connecting bars,
depending on the configuration with other devices.
Control and auxiliary circuits
The solenoid coils of the contactor relays have an extended coil
operating range from 0.7 to 1.25 x Us and are fitted as standard
with varistors to provide protection against overvoltage. The
opening delay is consequently 2 to 5 ms longer than for standard contactors.
Ambient temperature
The permissible ambient temperature for operation of the
contactors (across the full solenoid coil operating range) is
-50 to +70 °C. Uninterrupted duty at temperatures < -25 °C and
> +55 °C reduces the mechanical endurance, the currentcarrying capacity of the conducting paths and the switching
frequency.
5
A clearance of 10 mm is required for side-by-side mounting at
ambient temperatures > 55 °C. There is no need to reduce the
technical specifications.
■ Technical specifications
Contactor relay
Type
3TH42
General technical specifications
Permissible ambient temperature
• During operation
°C
-50 ... +701)
• During storage
°C
-55 ... +80
Control circuit
0.7 ... 1.25 x Us
Solenoid coil operating range
Power consumption of the solenoid coils (for cold coil)
0.7 x Us W
1.0 x Us W
1.25 x Us W
(For cold coil: Closing = Closed)
2.6
5.2
8.2
Permissible residual current of the electronics (with 0 signal)
 10 mA x (24 V/Us)
• DC operation
Operating times
(Total break time = OFF-delay + Arcing time)
• Closing
- 0,7 x Us
ON-delay (NO)
OFF-delay (NC)
ms
ms
70 ... 200
28 ... 33
- 1 x Us
ON-delay (NO)
OFF-delay (NC)
ms
ms
45 ... 80
30 ... 34
- 1.25 x Us
ON-delay (NO)
OFF-delay (NC)
ms
ms
40 ... 60
31 ... 35
OFF-delay (NO)
ON-delay (NC)
ms
ms
20 ... 30
22 ... 32
ms
10
• Opening
- 0.7 ... 1.25 x Us
• Arcing time
1)
Side-by-side mounting with 10 mm distance.
All details and technical specifications not mentioned here are
identical to those of the standard versions; see page 5/16.
Siemens IC 10 · 2014
5/37
© Siemens AG 2013
Contactor Relays
Contactors with Extended Operating Range 0.7 ... 1.25 x Us for Railway Applications
3TH4 contactor relays
■ Selection and ordering data
Solenoid coil fitted with varistor
3TH4244-0L. .
5
Contacts Rated operational current
Ie/AC-15/AC-14
Number
230 V
400 V
500 V
690 V
A
A
A
A
Contacts1)
Ident. No.
acc. to
EN 50011
Rated control supply
voltage Us
DT Screw terminals
Version
NO
NC
Article No.
PU
(UNIT,
SET, M)
PS*
PG
Price
per PU
V DC
For screw fixing and snap-on mounting onto TH 35 standard mounting rail
DC operation
A1(+)
A2( )
8
10
6
4
2
A2( )
10
6
4
2
A2( )
1)
10
6
4
2
62E
4
24
110
}
}
3TH4244-0LB4
3TH4244-0LF4
1
1
1 unit
1 unit
41A
41A
}
}
3TH4253-0LB4
3TH4253-0LF4
1
1
1 unit
1 unit
41A
41A
}
}
3TH4262-0LB4
3TH4262-0LF4
1
1
1 unit
1 unit
41A
41A
13 23 33 43 53 61 71 81
14 24 34 44 54 62 72 82
5
53E
A1(+)
8
14 24 34 44 52 62 72 82
4
44E
A1(+)
8
13 23 33 43 51 61 71 81
3
24
110
13 23 33 43 53 61 71 83
14 24 34 44 54 62 72 84
6
2
24
110
Contacts not extendable.
Accessories see page 5/22.
5/38
Siemens IC 10 · 2014
* You can order this quantity or a multiple thereof.
Illustrations are approximate
© Siemens AG 2013
Coupling Relays
3TX7 Coupling Relays, Narrow Design
Relay couplers
■ Overview
The semiconductor couplers have a low power consumption
and are therefore particularly well suited for solid-state systems.
In the coupling links in double-decker design, the connections
are arranged on two levels; these units are extremely compact.
Connection method: Screw terminals or spring-type terminals.
For test purposes, versions are available with manual-0-automatic switches.
I/O devices
110 V AC
230 V AC
Electronic control
24 V DC
Pushbutton Coupling
Position
link
switch
The input and output coupling links differ with regard to the positioning of the terminals and the LEDs. For equipment identification purposes, each coupling link has a blank labeling plate.
24 V DC
Output
IEC 60947-5-1, EN 60947-5-1
Input
AC and DC operation
Actuators
110 V AC
230 V AC
M
NSB0_00186
Coupling
link
Motor
contactor
Application example: Motor control
Type
3TX7002, 3TX7003
3TX7004, 3TX7005
mm
W x 60 x 62
B x 80 x 85
Rated insulation voltage Ui (pollution degree 3)
V
300
Protective separation1) between coil and contacts
acc. to IEC 60947-1, Appendix N
V
Up to 300 AC
°C
°C
-25 ... +60
-40 ... +80
H
Dimensions (W x H x D)
5
■ Technical specifications
D
For width B see "Selection and ordering data"
W
General technical specifications
Permissible ambient temperature
• During operation
• During storage
Degree of protection
• Connections
• Enclosure
IP20
IP30
Short-circuit protection
• Short-circuit test with fuse links of operational class gG
with short-circuit current Ik = 1 kA acc. to IEC 60947-5-1
A
4
Conductor cross-sections
For 3TX7002, 3TX7004:
Screw terminals
mm2
mm2
• Solid
• Finely stranded with end sleeve
• Terminal screws
- Corresponding opening tool
1 x (0.25 ... 4)
1 x (0.5 ... 2.5)
M3
Screwdriver, size 3.5 mm x 0.5 mm
For 3TX7003, 3TX7005:
Spring-type terminals
mm2
mm2
• Solid or finely stranded
• Finely stranded with end sleeve
• Corresponding opening tool
1)
1 x (0.08 ... 2.5)
1 x (0.25 ... 1.5)
Screwdriver, size 3.0 mm x 0.5 mm (3RA2908-1A)
For 3TX700.-1FB02, no protective separation acc. to IEC 60947-1,
Appendix N.
Type
3TX7002-,
3TX7003-
1AB00 1BB00 1FB02
1AB02
1CB00 2AB00 2AE00
1BF00
2BF02
2AF00
2AF05
Control side
0.8 ... 1.25 x Us
Operating range
0.8 ... 1.1 x Us
Power consumption
• At Us = 24 V AC/DC
• At Us = 230 V AC/DC
W
W
Type
0.75
--
1.2
--
3TX7004, 3TX7005
0.75
--
-1.2
Exception: 3TX7005-...05
Control side
Operating range
• At Us = 24 V AC/DC
• At Us = 110 V AC/DC and 230 V
- Exception: 3TX7005-1LN00
0.7 ... 1.25 x Us
0.8 ... 1.1 x Us
0.7 ... 1.25 x Us
Power consumption
• At Us = 24 V AC/DC
• At Us = 230 V AC
• At Us = 230 V DC
VA/W
VA
W
0.5
-6
1
Siemens IC 10 · 2014
5/39
© Siemens AG 2013
Coupling Relays
3TX7 Coupling Relays, Narrow Design
Relay couplers
Type
3TX7002,
3TX7003
Exception: 3TX7002-1CB00
Load side
Rated operational currents Ie1)
Conventional thermal current Ith
A
6
Rated operational current Ie
acc. to utilization categories (IEC 60947-5-1)
• AC-15
At 24 ... 230 V
A
3
• DC-13
At 24 V
At 110 V
At 230 V
A
A
A
1
0.2
0.1
2
5
Switching current
for resistive load acc. to IEC 60947-5-1
• AC-12
At 24 ... 230 V
A
6
• DC-12
At 24 V
At 110 V
At 230 V
A
A
A
6
0.2
0.2
AC/DC
V
24 ... 250
Switching voltage
Min. contact load for 3TX700.-. . .02
1 V AC/DC/0.1 A
Mechanical endurance
Operating cycles 10 x 106
Electrical endurance at Ie
Operating cycles 1 x 105
Type
3TX7004-1B, -1L,
3TX7005-1L
3TX7004-.M,
3TX7005-.M,
Load side
Rated operational currents Ie1)
Conventional thermal current Ith
A
6
Rated operational current Ie
acc. to utilization categories (IEC 60947-5-1)
• AC-15
At 24 ... 230 V
A
3
• DC-13
At 24 V
At 110 V
At 230 V
A
A
A
1
0.2
0.1
2
Switching current for resistive load acc. to IEC 60947-5-1
• AC-12
At 24 ... 230 V
A
6
• DC-12
At 24 V
At 110 V
At 230 V
A
A
A
6
0.3
0.2
V
mA
30
20
V
17 ... 250
Power limit for hard gold-plating
• Voltage
• Current
Switching voltage
AC/DC
Min. switching voltage (reliability 1 ppm)
• Standard contacts
• Hard gold-plated contacts
17 V DC/5 mA
5 V DC/1 mA
Mechanical endurance
Operating cycles 10 x 106
Electrical endurance at Ie
Operating cycles 1 x 105
1)
Capacitive loads can result in micro-welding on the contacts.
Note:
If inductive loads are connected in parallel, the endurance of the
relay couplers can be increased.
5/40
Siemens IC 10 · 2014
0.5 x 106
© Siemens AG 2013
Coupling Relays
3TX7 Coupling Relays, Narrow Design
Relay couplers
Relay couplers – circuit diagrams for 3TX7002, 3TX7003
Terminal designations acc. to EN 50005
Output/input coupling
links
Output coupling links
3TX7002-1AB00
3TX7002-1AB02
3TX7002-2A.00
3TX7002-2AF05
3TX7002-1BB00
3TX7002-1BF00
Input coupling links
3TX7002-1CB00
3TX7002-1FB02
3TX7002-2BF02
3TX7003-1CB00
3TX7003-1BB00
3TX7003-1AB00
A1
13
A1
14
A2 A2
A1 A1
12 14
A2 A2
NSB0_00189
NSB0_00188
13 23
A1
14 24
A2
11
21
NSB0_00192
NSB0_00191a
NSB0_00190
11
A1
12 14 22 24
12 14
A2
5
A2
11
Relay couplers – circuit diagrams for 3TX7004, 3TX7005
Output coupling links
Input coupling links
3TX700.-1M.00
3TX700.-1BB00
3TX700.-1BF05
3TX700.-1L.0.
A1
A1
14
A1
A1
12
14
A2
13
NSB0_00205
3TX700.-1BB10
12
14
A2
11
A2
A2
NSB0_00207
11
11
NSB0_00208
3TX700.-2M.02
A
0
M
A1
A1
A2
14
12
14
A3
13
NSB0_00213
A2
A2
NSB0_00209
11
11
hGdGhœ›–”ˆ›Š
WGdGŒ™–G—–š›–•
tGdGtˆ•œˆ“
Siemens IC 10 · 2014
5/41
© Siemens AG 2013
Coupling Relays
3TX7 Coupling Relays, Narrow Design
Relay couplers
■ Selection and ordering data
AC and DC operation · for snap-on mounting onto TH 35 standard mounting rail
Rated control supply
voltage Us
(at AC: 50/60 Hz)
Contacts
Version
V
NO
Width W
CO
DT
Article No.
Price
per PU
PU
(UNIT,
SET, M)
PS*
PG
mm
Relay coupling links 3TX7002
Screw terminals
5
Output coupling links
3TX7002-1AB00
24 AC/DC
1
--
11.5
}
3TX7002-1AB00
1
1 unit
41H
24 AC/DC
11)
--
11.5
}
3TX7002-1AB02
1
1 unit
41H
24 AC/DC
--
1
17.5
}
3TX7002-1BB00
1
1 unit
41H
230 AC/DC3)
--
1
17.5
}
3TX7002-1BF00
1
1 unit
41H
24 AC/DC
22)
--
22.5
}
3TX7002-1CB00
1
1 unit
41H
24 AC/DC
--
21) 2)
22.5
}
3TX7002-1FB02
1
1 unit
41H
24 AC/DC
1
--
11.5
}
3TX7002-2AB00
1
1 unit
41H
110 AC/DC4)
1
--
11.5
}
3TX7002-2AE00
1
1 unit
41H
230 AC/DC3)
12)
--
11.5
}
3TX7002-2AF00
1
1 unit
41H
230 AC/DC
12)
--
11.5
}
3TX7002-2AF05
1
1 unit
41H
230 AC/DC3)
--
11)
17.5
}
3TX7002-2BF02
1
1 unit
41H
Input coupling links
Relay coupling links 3TX7003
Output coupling links
Spring-type
terminals
24 AC/DC
1
--
11.5
}
3TX7003-1AB00
1
1 unit
41H
24 AC/DC
--
1
17.5
}
3TX7003-1BB00
1
1 unit
41H
24 AC/DC
22)
--
22.5
}
3TX7003-1CB00
1
1 unit
41H
1
--
11.5
A
3TX7003-2AF00
1
1 unit
41H
Input coupling links
230 AC/DC
3TX7003-1BB00
1)
Hard gold-plated contacts.
2)
Different potential up to 300 V permitted; no protective separation.
3)
Observe max. permissible cable length for AC control voltage: 7 m.
4)
Observe max. permissible cable length for AC control voltage: 15 m.
Note:
For coil voltages which are not listed, SITOP DC power supplies
can be used, e.g. 6EP1331-5BA00 or 6EP1331-5BA10;
see Chapter 15, "Stabilized Power Supplies" ➞ "SITOP Power
Supplies".
Note:
A clearance of at least 10 mm between the modules or to
adjacent contacts is required for operation with rated voltage
and 100 % ON period over 24 hours a day.
5/42
Siemens IC 10 · 2014
* You can order this quantity or a multiple thereof.
Illustrations are approximate
© Siemens AG 2013
Coupling Relays
3TX7 Coupling Relays, Narrow Design
Relay couplers
Rated control supply Contacts
voltage Us
Version
(at AC: 50/60 Hz)
V
NO
Manual-0automatic
switch for
testing
purposes
CO
Width W
DT Article No.
Price
per PU
PU
(UNIT,
SET, M)
PS*
PG
mm
3TX7004 relay couplers
Output coupling links
24 AC/DC
--
1
Without
6.2
}
3TX7004-1LB00
1
1 unit
41H
24 AC/DC
--
12)
Without
6.2
}
3TX7004-1LB02
1
1 unit
41H
24 AC/DC
--
1
With
12.5
}
3TX7004-1BB10
1
1 unit
41H
230 AC/DC
--
1
Without
6.2
}
3TX7004-1LF00
1
1 unit
41H
230 AC/DC
--
1
Without
12.51)
}
3TX7004-1BF05
1
1 unit
41H
24 AC/DC
1
--
Without
6.2
}
3TX7004-1MB00
1
1 unit
41H
230 AC/DC
1
--
Without
6.2
}
3TX7004-1MF00
1
1 unit
41H
24 AC/DC
12)
--
Without
6.2
}
3TX7004-2MB02
1
1 unit
41H
110 AC/DC
12)
--
Without
6.2
}
3TX7004-2ME02
1
1 unit
41H
230 AC/DC
12)
--
Without
6.2
}
3TX7004-2MF02
1
1 unit
41H
Input coupling links
3TX7005 relay couplers
Spring-type
terminals
Output coupling links
3TX7005-2MB02
24 AC/DC
--
1
Without
6.2
}
3TX7005-1LB00
1
1 unit
41H
24 AC/DC
--
12)
Without
6.2
}
3TX7005-1LB02
1
1 unit
41H
110 AC/DC3)
--
1
Without
6.2
B
3TX7005-1LN00
1
1 unit
41H
230 AC/DC
--
1
Without
6.2
}
3TX7005-1LF00
1
1 unit
41H
24 AC/DC
1
--
Without
6.2
}
3TX7005-1MB00
1
1 unit
41H
230 AC/DC
1
--
Without
6.2
}
3TX7005-1MF00
1
1 unit
41H
24 AC/DC
12)
--
Without
6.2
C
3TX7005-2MB02
1
1 unit
41H
230 AC/DC
12)
--
Without
6.2
B
3TX7005-2MF02
1
1 unit
41H
Input coupling links
1)
For long cables.
2)
Hard gold-plated contacts.
3)
Extended operating range 0.7 ... 1.25 x US.
Note:
Note:
For replacement products see 3RS18 coupling links with
industrial enclosure or other 3TX70 products.
A clearance of at least 10 mm between the modules or to adjacent contacts is required for operation with rated voltage and
100 % ON period over 24 hours a day.
For coil voltages which are not listed, SITOP DC power supplies
can be used, e.g. 6EP1331-5BA00 or 6EP1331-5BA10;
see Chapter 15, "Stabilized Power Supplies" ➞ "SITOP Power
Supplies".
■ Accessories
For coupling links
Version
DT Article No.
For linking the same potentials
}
A
Price
per PU
PU
(UNIT,
SET, M)
PS*
PG
3TX7004-8AA00
1
1 unit
41H
3TX7004-8BA00
1
1 unit
41H
Type
Connecting comb, blue
3TX7004
24 terminals,
current carrying capacity for infeed
max. 26 A
Width 6.2 mm
3TX7004-8AA00
Connecting cable, blue
3TX7002 and 3TX7004 with
screw terminals
3TX7003 and 3TX7005 with
spring-type terminals
With supply cable, blue
24 terminals,
current carrying capacity for infeed
max. 12 A
Length of cable between two terminals
approx. 11 cm
3TX7004-8BA00
* You can order this quantity or a multiple thereof.
Illustrations are approximate
Siemens IC 10 · 2014
5/43
5
3TX7004-1LB0.
Screw terminals
© Siemens AG 2013
Coupling Relays
3TX7 Coupling Relays, Narrow Design
Relay couplers with plug-in design
■ Overview
■ Benefits
• Plug-in base couplers with spring-type terminals in width
6.2 mm
• Fast exchange with existing wiring (plug-in relay)
• Tested complete units ➞ shorter mounting time
• Single relays available as components
• The wire inlet and terminals can be reached from the front.
This results in faster wiring time and wiring errors are
prevented.
• Linking of control supply voltage and control signals with
16-pole connecting comb
• Galvanic isolation plate for isolating different voltages for
neighboring units
• Integrated reverse polarity protection and
EMC arc-suppression diode
• Clearly visible functional state of the relay coupler by yellow
LED
• Protective separation according to IEC 61140
• Device variants with hard gold-plated contacts, hence high
contact reliability
• 230 V AC/DC versions available
Coupling links are used to connect signals from and to a PLC.
The plug-in relays enable the relay to be replaced at the end of
its service life without detaching the wiring.
For easy linking of the signals, each terminal can be jumpered
using an external connecting comb.
Note:
5
A clearance of at least 10 mm between the modules or to adjacent contacts is required for operation with rated voltage and
100 % ON period over 24 hours a day.
■ Technical specifications
Type
3TX7014, 3TX7015
mm
6.2 x 90 x 92
mm
1 x 89.2 x 94.2
Rated insulation voltage Ui (pollution degree 2)
V
300
Protective separation
between coil and contacts acc. to IEC 60947-1, Appendix N
V
Up to 300 AC
°C
°C
-25 ... +55
-40 ... +80
D
• Galvanic isolation plate 3TX7014-7CE00
H
Dimensions (W x H x D)
W
General technical specifications
Permissible ambient temperature
• During operation
• During storage
Degree of protection
• Enclosure
• Relays
IP20
IP40
Short-circuit protection
• Short-circuit test with fuse links of operational class gG
with short-circuit current Ik = 1 kA acc. to IEC 60947-5-1
A
4
Conductor cross-sections
For 3TX7014:
Screw terminals
• Solid
• Finely stranded with or without end sleeve
mm2
mm2
1 x (0.5 ... 2.5)
1 x (0.5 ... 1.5)
M2.5
Screwdriver, 3.0 mm x 0.5 mm (3RA29 08-1A)
• Terminal screws
- Corresponding opening tool
For 3TX7015:
Spring-type terminals
• Solid or finely stranded
• Finely stranded with end sleeve
mm2
2
mm
1 x (0.5 ... 2.5)
1 x (0.5 ... 1.5)
• Corresponding opening tool
Screwdriver, 3.0 mm x 0.5 mm (3RA2908-1A)
Type
3TX701.-1.M
3TX701.-1.B
3TX701.-1.E
3TX701.-1.F
0.85 ... 1.1Us
0,7 ... 1.25 Us
0.8 ... 1.1 Us
0.8 ... 1.1 Us
Control side
Operating range
Power consumption, max.
• At Us = 24 V
• At Us = 115 V
• At Us = 230 V
Protection circuit
• DC
• AC
5/44
Siemens IC 10 · 2014
W
W
W
0.5
0.5
1
Freewheel diode + Reverse polarity protection
Rectifier bridge
© Siemens AG 2013
Coupling Relays
3TX7 Coupling Relays, Narrow Design
Relay couplers with plug-in design
Type
3TX7014, 3TX7015
Load side
Rated currents1)
• Conventional thermal current Ith
A
5
- AC-15
At 24 ... 230 V A
3
- DC-13
At 24 V A
At 110 V A
At 230 V A
• Rated operational currents Ie
1
0.2
0.1
AC/DC V
Switching voltage
24 ... 250
Min. contact load (reliability 1 ppm)
• Standard contact
• Hard gold-plated contacts
17 V DC/5 mA
5 V DC/1 mA
Mechanical endurance
Operating cycles 10 x 106
Electrical endurance at Ie acc. to AC-15
Operating cycles 1 x 105
Note:
Capacitive loads can result in micro-welding on the contacts.
If inductive loads are connected in parallel, the endurance of the
relay couplers can be increased.
Connections
Terminal designations acc. to EN 50005
1 NO
1 CO contact
3TX7014-1AM00
3TX7015-1AM00
3TX7014-1B .. .
3TX7015-1B .. .
NO
14
(+)A1
COIL
13
COM
COIL NC NO
(-)A2 12 14
IC01_00208
COIL
-A2
13
COM
IC01_00207
+A1
COIL
■ Selection and ordering data
Rated control supply voltage Us
(at AC: 50/60 Hz)
Contacts
Version
DT Screw terminals
Article No.
V
NO
PU
(UNIT,
SET, M)
PS*
PG
Price
per PU
CO
Plug-in base couplers, width 6.2 mm,
complete with relay
24 DC
1
--
A
3TX7014-1AM00
1
5 units
41H
24 DC
--
1
A
3TX7014-1BM00
1
5 units
41H
24 AC/DC
--
1
A
3TX7014-1BB00
1
5 units
41H
115 AC/DC
--
1
A
3TX7014-1BE00
1
5 units
41H
230 AC/DC
--
1
A
3TX7014-1BF00
1
5 units
41H
24 DC
--
1
A
3TX7014-1BM02
1
5 units
41H
24 AC/DC
--
1
A
3TX7014-1BB02
1
5 units
41H
115 AC/DC
--
1
A
3TX7014-1BE02
1
5 units
41H
230 AC/DC
--
1
A
3TX7014-1BF02
1
5 units
41H
3TX7014-1AM00
With hard gold-plated contacts1)
1)
The versions with hard gold-plated contacts feature high contact reliability
(also for low currents) and are therefore especially suitable for solid-state
inputs of programmable logic controllers.
* You can order this quantity or a multiple thereof.
Illustrations are approximate
Siemens IC 10 · 2014
5/45
5
1)
© Siemens AG 2013
Coupling Relays
3TX7 Coupling Relays, Narrow Design
Relay couplers with plug-in design
Rated control supply voltage Us
(at AC: 50/60 Hz)
Contacts
Version
DT Spring-type
terminals
Article No.
V
NO
PU
(UNIT,
SET, M)
PS*
PG
Price
per PU
CO
Plug-in base couplers, width 6.2 mm,
complete with relay
24 DC
1
--
A
3TX7015-1AM00
1
5 units
41H
24 DC
--
1
A
3TX7015-1BM00
1
5 units
41H
24 AC/DC
--
1
A
3TX7015-1BB00
1
5 units
41H
115 AC/DC
--
1
A
3TX7015-1BE00
1
5 units
41H
230 AC/DC
--
1
A
3TX7015-1BF00
1
5 units
41H
5
With hard gold-plated contacts1)
1)
24 DC
--
1
A
3TX7015-1BM02
1
5 units
41H
24 AC/DC
--
1
A
3TX7015-1BB02
1
5 units
41H
115 AC/DC
--
1
A
3TX7015-1BE02
1
5 units
41H
230 AC/DC
--
1
A
3TX7015-1BF02
1
5 units
41H
The versions with hard gold-plated contacts feature high contact reliability
(also for low currents) and are therefore especially suitable for electronic
inputs of programmable logic controllers.
■ Accessories
For coupling links Rated control supply
voltage Us
Version
DT Article No.
Price
per PU
PU
(UNIT,
SET, M)
PS*
PG
V
Replacement relay modules, width 6.2 mm, 1 changeover contact
For complete unit
3TX7014 and
3TX7015
12 DC
3TX7014 and
3TX7015
24 DC
3TX7014 and
3TX7015
60 DC
• 24 V AC/DC
A
3TX7014-7BQ00
1 20 units
41H
• 24 V DC,
hard gold-plated
A
3TX7014-7BQ02
1 20 units
41H
• 24 V DC
A
3TX7014-7BM00
1 20 units
41H
• 24 V DC,
hard gold-plating
A
3TX7014-7BM02
1 20 units
41H
• 115 V or 230 V AC/DC
A
3TX7014-7BP00
1 20 units
41H
• 115 V or 230 V AC/DC, A
hard gold-plated
3TX7014-7BP02
1 20 units
41H
For linking the same
potentials
A
3TX7014-7AA00
1
5 units
41H
A
3TX7014-7CE00
1 10 units
41H
Connecting comb, blue
3TX7014 and
3TX7015
--
16 terminals,
current carrying capacity
for infeed max. 6 A
3TX7014-7AA00
Galvanic isolation plates
3TX7014 and
3TX7015
--
--
3TX7014-7CE00
Assignment of replacement relay modules
Plug-in base couplers
Replacement modules
Standard contacts
Hard gold-plated contacts
Us
Contact
Standard contacts
Hard gold-plated contacts
3TX701.-1AM00
--
24 V DC
1 NO
3TX7014-7BM00
--
3TX701.-1BM00
3TX701.-1BM02
24 V DC
1 CO contact
3TX7014-7BM00
3TX7014-7BM02
3TX701.-1BB00
3TX701.-1BB02
24 V AC/DC
3TX7014-7BQ00
3TX7014-7BQ02
3TX701.-1BE00
3TX701.-1BE02
115 V AC/DC
3TX7014-7BP00
3TX7014-7BP02
3TX701.-1BF00
3TX701.-1BF02
230 V AC/DC
3TX7014-7BP00
3TX7014-7BP02
More information about replacement relay modules
see Product Support:
http://support.automation.siemens.com/WW/view/en/34803536
5/46
Siemens IC 10 · 2014
* You can order this quantity or a multiple thereof.
Illustrations are approximate
© Siemens AG 2013
Coupling Relays
3TX7 Coupling Relays, Narrow Design
Semiconductor couplers
■ Overview
AC and DC operation
Surge suppression
IEC 60947, EN 60947,
IEC 60664-1, EN 60664-1 and EN 50005;
optocouplers: IEC 60747-5, EN 60747-5;
programmable controllers: IEC 61131-2
In the case of optocouplers, the contact element is a semiconductor. These are not subject to wear; so welding is not possible.
The input and output coupling links differ with regard to the positioning of the terminals and the LEDs. For equipment identification purposes, each coupling link has a blank labeling plate.
With semiconductors, the switching current is not dependent on
the inductance of the load, i.e. the switching current for a DC-13
load is the same as that for an inductive DC-12 load.
The semiconductor couplers have a low power consumption
and are therefore particularly well suited for solid-state systems.
This means that coupling links with a semiconductor output are
particularly suitable for inductive loads such as solenoid valves.
It is not relevant to specify any number of operating cycles because this does not affect the endurance of the semiconductor
provided it is not overheated.
In the coupling links in double-decker design, the connections
are arranged on two levels; these units are extremely compact.
For test purposes, versions are available with manual-0-automatic switches. This design can also be supplied with springtype terminals.
5
Note:
■ Technical specifications
Type
3TX7002
3TX7004, 3TX7005
mm
W x 60 x 62
W x 80 x 85
Rated insulation voltage Ui
(pollution degree 3)
V
300
Optoelectronic coupling elements:
Protective separation
acc. to IEC 60947-1, Appendix N
V
Up to 300
°C
°C
-25 ... +60
-40 ... +80
D
For width W see
"Selection and ordering data"
H
Dimensions (W x H x D)
W
General technical specifications
Permissible ambient temperature
• During operation
• During storage
Conductor cross-sections
For 3TX7002, 3TX7004:
• Solid
• Finely stranded with end sleeve
Screw terminals
mm2
2
mm
• Terminal screws
- Corresponding opening tool
1 x (0.25 ... 4)
1 x (0.5 ... 2.5)
M3
Screwdriver, size 3.0 mm x 0.5 mm (3RA29 08-1A)
For 3TX7005:
• Solid or finely stranded
• Finely stranded with end sleeve
• Corresponding opening tool
Spring-type terminals
mm2
2
mm
---
1 x (0.08 ... 2.5)
1 x (0.25 ... 1.5)
--
Screwdriver, size 3.0 mm x 0.5 mm
(3RA2908-1A)
Siemens IC 10 · 2014
5/47
© Siemens AG 2013
Coupling Relays
3TX7 Coupling Relays, Narrow Design
Semiconductor couplers
Type
3TX7002-3AB00
3TX7002-3AB01
3TX7002-4AB00
3TX7002-4AG00
V
17 ... 30 DC
11 ... 30 DC
17 ... 30 AC/DC
88 ... 264 AC
• At 17 V DC
• At 24 V DC
• At 30 V DC
mA
mA
mA
18
20
22
5
7
8.5
----
----
• At 17 V AC/DC
• At 24 V AC/DC
• At 30 V AC/DC
mA
mA
mA
----
----
10
14
18
----
• At 88 V AC/DC
• At 230 V AC/DC
• At 264 V AC/DC
mA
mA
mA
----
----
----
9
24
28
Switching current
A
1.8
1.5 2)
0.1
0.1
Short-time loading capacity
A
ms
20
20
4
200
1
20
1
20
V
48 ... 264
--
- 60
- 30
- 30
Minimum load current
mA
60
--
--
--
Voltage drop conducting
V
 1.5
 1.1
 1.7
 0.3
Control side
Operating range
Power consumption, max.
Switching voltage (operating range)1)
• Effective AC 50/60 Hz
• DC
1)
Comply with minimum switching voltage for 3TX7002-3AB00.
2)
See derating diagram.
Type
3TX70043TX7005-
3AB04
3AC.4
3AC03
3PB54
3PB74
4PG24
3PG74
Control side
V
Operating range
110 ... 230 88 ... 253
AC/DC
AC/DC
11 ... 30 DC
Power consumption, max.
• At 24 V DC
• At 110 V DC
• At 230 V AC
W
W
VA
0.5
---
Switching voltage
0.25
---
0.2
---
--1.5
-0.2
1.5
V
10 ... 48
DC
10 ... 30
DC
24 ... 250 10 ... 30
AC
DC
11 ... 30
DC
10 ... 30
DC
11 ... 30
DC
Switching current
A
0.5
5
2
1.5
3
0.1
3
A
1.5
100
• Duration
ms
20
Shortcircuit
proof1)
--
Short-circuit proof2)
0.2
20
--
--
3
Shortcircuit
proof2)
--
Minimum load current
mA
--
5003)
50
--
--
--
--
Load side
Short-time loading capacity
• Current
1)
In the event of a short circuit or overload, the semiconductor output
switches off. In order to operate the device again, it must be temporarily
disconnected from the power supply.
2)
In the event of a short circuit or overload, the current is limited by the
semiconductor output.
Derating diagram for 3TX7002-3AB01
(A)
Continuous
current per
channel
1,5
1
Separate
Between
2 modules
with 5 mm
clearance each
and 1 W power
loss each
0,5
NSB0_00187
5
Load side
20
40
60
u (°C)
Load current as a function of ambient temperature Tu
5/48
Siemens IC 10 · 2014
3)
If the current falls below the minimum load current, the built-in semiconductor detects an open circuit in the load circuit. The control must be temporarily switched off for resetting.
© Siemens AG 2013
Coupling Relays
3TX7 Coupling Relays, Narrow Design
Semiconductor couplers
Semiconductor couplers – circuit diagrams
Terminal designations acc. to EN 50005
Output coupling links
Input coupling links
3TX7002-3AB00
A1
3TX7002-3AB01
A1
13
3TX7002-4AB00
A1
13
3TX7002-4AG00
13
A1
14
A2
13
NSB0_00193
NSB0_00195
NSB0_00196
NSB0_00194
A2
14
14
A2
A2
14
Output coupling links
3TX700.-3PB54
3TX700.-3PG74
3TX700.-3PB74
A1
3TX700.-3AC04
5
3TX700.-3AB04
3TX700.-3PB41
A1
A1
+13
+13
A2
+
A1
+13
+13
A2
14
NSB0_00214
NSB0_00215
Load
0V
Load
_
A2
14
NSB0_00216
Output coupling links
3TX700.-3AC03
A1
A1
+13
+13
~13
~13
14
NSB0_00219
A2
~14
NSB0_00218
14
0V
+13
A2
A2
+
A2
NSB0_00217
Load
_
3TX700.-4AB04
A1
A
0
M
A1
A2
0V
Input coupling links
3TX700.-3AC14
A3
+
A2
14
Load
_
Load
~14
Load
hGdGhœ›–”ˆ›Š
WGdGŒ™–G—–š›–•
tGdGtˆ•œˆ“
Siemens IC 10 · 2014
5/49
© Siemens AG 2013
Coupling Relays
3TX7 Coupling Relays, Narrow Design
Semiconductor couplers
■ Selection and ordering data
AC and DC operation · For snap-on mounting onto TH 35 standard mounting rail
Rated control
supply voltage Us
(at AC: 50/60 Hz)
Switching
voltage
Switching Manual-0current
automatic
switch for
testing
purposes
Width W
V
V
A
mm
DT
Article No.
Price
per PU
PU
(UNIT,
SET,
M)
PS*
PG
3TX7002 semiconductor couplers, 1 transistor
Screw terminals
Output coupling links
24 DC
48 ... 264 AC
1.8
--
11.5
}
3TX7002-3AB00
1
1 unit
41H
60 < DC
1.5
--
11.5
}
3TX7002-3AB01
1
1 unit
41H
5
Input coupling links
24 AC/DC
30 < DC
0.1
--
11.5
}
3TX7002-4AB00
1
1 unit
41H
110 … 240 AC
30 < DC
0.1
--
11.5
}
3TX7002-4AG00
1
1 unit
41H
3TX7002-3AB00
3TX7004 semiconductor couplers
Output coupling links
3TX7004-3AB04
24 DC
 48 DC
0.5
--
6.2
}
3TX7004-3AB04
1
1 unit
41H
24 DC
11 ... 30 DC
1.5
--
6.2
}
3TX7004-3PB54
1
1 unit
41H
24 DC
 30 DC
3
--
6.2
}
3TX7004-3PB74
1
1 unit
41H
110 ... 230 AC/DC
 30 DC
3
--
6.2
A
3TX7004-3PG74
1
1 unit
41H
24 DC
 30 DC
5
--
12.5
}
3TX7004-3AC04
1
1 unit
41H
24 DC
 30 DC
5
Yes
12.5
B
3TX7004-3AC14
1
1 unit
41H
24 DC
24 ... 250 AC
2
--
12.5
}
3TX7004-3AC03
1
1 unit
41H
0.1
--
6.2
}
3TX7004-4PG24
1
1 unit
41H
Input coupling links
110 ... 230 AC/DC
 30 DC
3TX7005 semiconductor couplers
Spring-type
terminals
Output coupling links
3TX7005-3AB04
24 DC
 48 DC
0.5
--
6.2
}
3TX7005-3AB04
1
1 unit
41H
24 DC
11 ... 30 DC
1.5
--
6.2
}
3TX7005-3PB54
1
1 unit
41H
24 DC
 30 DC
3
--
6.2
A
3TX7005-3PB74
1
1 unit
41H
110 ... 230 AC/DC
 30 DC
--
6.2
A
3TX7005-3PG74
1
1 unit
41H
24 DC
 30 DC
--
12.5
}
3TX7005-3AC04
1
1 unit
41H
24 DC
 30 DC
Yes
12.5
C
3TX7005-3AC14
1
1 unit
41H
24 DC
24 ... 250 AC
2
--
12.5
C
3TX7005-3AC03
1
1 unit
41H
0.1
--
6.2
}
3TX7005-4PG24
1
1 unit
41H
5
Input coupling links
110 ... 230 AC/DC
 30 DC
Note:
For replacement products, see 3RS18 coupling links with
industrial enclosure or other 3TX70 products.
For coil voltages which are not listed, SITOP DC power supplies
can be used, e.g. 6EP1331-5BA00 or 6EP1331-5BA10;
see Chapter 15, "Stabilized Power Supplies" ➞ "SITOP Power
Supplies".
■ Accessories
For coupling links
Version
DT Article No.
For linking the same potentials
}
A
Price
per PU
PU
(UNIT,
SET,
M)
PS*
PG
3TX7004-8AA00
1
1 unit
41H
3TX7004-8BA00
1
1 unit
41H
Type
Connecting comb, blue
3TX7004
24 terminals,
current carrying capacity for infeed
max. 26 A
Width 6.2 mm
3TX7004-8AA00
Connecting cable, blue
3TX7002 and 3TX7004
with screw terminals
3TX7003 and 3TX7005
with spring-type terminals
With supply cable, blue
24 terminals,
current carrying capacity for infeed
max. 12 A
Length of cable between two terminals
approx. 11 cm
3TX7004-8BA00
5/50
Siemens IC 10 · 2014
* You can order this quantity or a multiple thereof.
Illustrations are approximate
© Siemens AG 2013
Coupling Relays
SIRIUS 3RS18 Coupling Relays with Industrial Enclosure
Relay couplers
■ Overview
Versions:
• Wide voltage range: One connection for a wide voltage range
• Combination voltage: Two connections for different voltage
ranges
• Versions with solid-state compatible outputs
(hard gold-plating)
• 1, 2 or 3 changeover contacts
The 3RS18 coupling relays are couplers in the proven 22.5 mm
industrial enclosure. This enclosure supports the same connection methods as for the 3RP15 timing relays, including springtype connection; 2 wires can be clamped.
The series comprises devices with up to 3 changeover contacts
with screw terminals or spring-type terminals as combination
voltage or wide voltage range versions.
The relay coils are protected internally with noise suppression
diodes.
■ Technical specifications
Type
3RS1800-.A...
3RS1800-.B...
3RS1800-.H...
mm
22.5 x 86 x 84
22.5 x 86 x 94
22.5 x 86 x 103
Rated insulation voltage Ui pollution degree 3
V
500
Protective separation acc. to IEC 60947-1, Appendix N
between the coil and the contacts and between the individual contacts.
V
300
°C
°C
-25 ... +60
-40 ... +80
D
5
H
Dimensions (W x H x D)
W
General technical specifications
Permissible ambient temperature
• During operation
• During storage
Degree of protection acc. to IEC 60529
• Enclosure
• Cover
IP20
IP40
Short-circuit protection
A
Short-circuit test with fuse links of operational class gG
with short-circuit current Ik = 1 kA acc. to IEC 60947-5-1
4
Conductor cross-sections
For 3RS1800-1:
Screw terminals
mm2
mm2
mm2
• Solid
• Finely stranded with end sleeve
• AWG cables, solid or stranded
• Terminal screw
- Corresponding opening tool
1 x (0.5 ... 4); 2 x (0.5 ... 2.5)
2 x (0.5 ... 2.5)
2 x (20 ... 14)
M3.5
Screwdriver, size 3.0 mm x 0.5 mm (3RA29 08-1A)
• Tightening torque
Nm
0.8 ... 1.2
For 3RS1800-2:
•
•
•
•
Spring-type terminals
mm2
mm2
mm2
AWG
Solid
Finely stranded without end sleeve
Finely stranded with end sleeve
AWG cables, solid or stranded
• Corresponding opening tool
2 x (0.25 ... 1.5)
2 x (0.25 ... 1.5)
2 x (0.25 ... 1)
2 x (24 ... 16)
Screwdriver, size 3.0 mm x 0.5 mm (3RA2908-1A)
Control side
0.85 ... 1.1 x Us
Operating range
Power consumption, max.
AC or DC VA/W
8/1
Load side
A
Conventional thermal current Ith
Rated operational currents Ie
• AC-15
• DC-13
Switching current for resistive load
• AC-12
• DC-12
Switching voltage
• Max. AC
• Max. DC
Min. contact load
• Standard contacts
• Hard gold-plated contacts
6
At 24 ... 400 V
At 24 V A
At 110 V A
At 230 V A
3
1
0.2
0.1
At 24 ... 400 V
At 24 V
At 115 V
At 230 V
A
A
A
A
5
5
0.2
0.2
V
V
400
250
17 V DC, 5 mA at 1 ppm fault
5 V DC, 1 mA at 1 ppm fault
Mechanical endurance
Operating cycles 10 x 106
Electrical endurance at Ie
Operating cycles 1 x 105
Siemens IC 10 · 2014
5/51
© Siemens AG 2013
Coupling Relays
SIRIUS 3RS18 Coupling Relays with Industrial Enclosure
Relay couplers
Circuit diagrams
Terminal designations acc. to EN 50005
3RS1800-.AP00,
3RS1800-.AQ00
3RS1800-.BP00,
3RS1800-.BQ00,
3RS1800-.BW00
A1 A3 11
A2
A1 A3 11
A2
12 14
3RS1800-.HP0.,
3RS1800-.HQ0.,
3RS1800-.HW0.
A1 A3 11
21
A2
12 14 22 24
21
31
12 14 22 24 32 34
Connection of the control supply voltage Us
3RS1800-..P0.,
3RS1800-..Q0.
3RS1800-..P0.,
3RS1800-..Q0.
3RS1800-..W0.
U S = 24 V AC/DC
U S = 110 ... 120 V AC
U S = 220 ... 240 V AC
U S = 24 ... 240 V AC/DC
L+
L+
L+
A2
L–
A1
A1
NSB0_02225
A3
A2
L–
A2
L–
NSB0_02226
A1
NSB0_02224
5
A3
Note:
The position of the connection points on the device is based on
the principle of logical separation, i.e. the coil terminals A1, A2,
A3 are above and the terminals for the changeover contacts 11,
12, 14 etc. are below.
■ Selection and ordering data
Rated control supply Connection Us Contacts
voltage Us
Version
(at AC: 50/60 Hz)
V
DT Article No.
Price
per PU
PU
(UNIT,
SET, M)
PS*
PG
CO
Coupling relays in industrial enclosure, 22.5 mm
Screw terminals
Wide voltage range
24 ... 240 AC/DC
A1 - A2
2
3
31)
A
A
A
3RS1800-1BW00
3RS1800-1HW00
3RS1800-1HW01
1
1
1
1 unit
1 unit
1 unit
41H
41H
41H
Combination voltage
24 AC/DC and
110 ... 120 AC
A3 - A2 or
A1 - A2
1
2
3
31)
A
A
A
C
3RS1800-1AQ00
3RS1800-1BQ00
3RS1800-1HQ00
3RS1800-1HQ01
1
1
1
1
1 unit
1 unit
1 unit
1 unit
41H
41H
41H
41H
24 AC/DC and
220 ... 240 AC
A3 - A2 or
A1 - A2
1
2
3
31)
A
A
A
A
3RS1800-1AP00
3RS1800-1BP00
3RS1800-1HP00
3RS1800-1HP01
1
1
1
1
1 unit
1 unit
1 unit
1 unit
41H
41H
41H
41H
3RS1800-1H. . .
Coupling relays in industrial enclosure, 22.5 mm
Wide voltage range
24 ... 240 AC/DC
Spring-type
terminals
A1 - A2
2
3
31)
A
A
A
3RS1800-2BW00
3RS1800-2HW00
3RS1800-2HW01
1
1
1
1 unit
1 unit
1 unit
41H
41H
41H
Combination voltage
24 AC/DC and
110 ... 120 AC
A3 - A2 or
A1 - A2
1
2
3
31)
C
A
C
C
3RS1800-2AQ00
3RS1800-2BQ00
3RS1800-2HQ00
3RS1800-2HQ01
1
1
1
1
1 unit
1 unit
1 unit
1 unit
41H
41H
41H
41H
24 AC/DC and
220 ... 240 AC
A3 - A2 or
A1 - A2
1
2
3
31)
A
A
A
A
3RS1800-2AP00
3RS1800-2BP00
3RS1800-2HP00
3RS1800-2HP01
1
1
1
1
1 unit
1 unit
1 unit
1 unit
41H
41H
41H
41H
3RS1800-2B. . .
1)
Hard gold-plated contacts.
5/52
Siemens IC 10 · 2014
* You can order this quantity or a multiple thereof.
Illustrations are approximate
© Siemens AG 2013
Coupling Relays
Coupling Relays with LZS/LZX Plug-In Relays
Plug-in relay couplers
■ Overview
Function
The semiconductor couplers have a low power consumption
and are therefore particularly well suited for solid-state systems.
In the versions equipped with LEDs, these indicate the switching
state. The LZS:PT/MT plug-in relay couplers have a test button.
This can be used to force the plug-in relay coupler into the
switching state and to lock it. This is indicated by a raised
petrol-colored lever.
Logical separation
The terminals for the contacts and the terminals for the coil are
arranged on separate levels, e.g. above for contacts and below
for coil. Logical separation is not necessarily protective separation.
Protective separation
For safe isolation, transfer of the voltage of one circuit to another
circuit is prevented to a suitable degree of safety (requirements
and tests are described in IEC 60947-1 in Appendix N).
Control with solid-state output
Notes on the previous LZX series
In the case of solid-state outputs (e.g. proximity switches) with
overload and short-circuit protection, you must make allowance
during configuration for the temporarily flowing capacitor charging currents! This is possible, for example, by using a suitable
LZS plug-in relay coupler.
The complete units and accessory parts of the LZX series are no
longer listed in this catalog. The complete units of the LZS series
are fully compatible with the corresponding units of the LZX series. Prices for the LZS series are lower than for the previous LZX
series.
Surge suppression
The LZX plug-in relays are available unchanged and are used
accordingly in both the LZS and the LZX series.
The 24 V DC relays LZX:RT and LZX: PT with LEDs can be supplied with, all others without integral surge suppression (freewheel diode connected in parallel with A1/A2). The positive control supply voltage must be connected to coil terminal A1.
Mounting
The relays are plugged into the base and this is snapped onto a
TH 35 standard mounting rail according to IEC 60715.
Note:
Due to differences in geometry the LED modules, plug-in bases,
retaining brackets and labels can be combined and/or used in
only the respective series, LZS or LZX.
The LZS series offers not only service-proven screw connections
but also versions with plug-in terminals (push-in).
A retaining bracket can be ordered for the MT series that additionally fixes the relay into a plug-in base (under conditions of increased mechanical stress). For the RT and PT series, a combined retaining and ejection bracket is available which can be
used to disassemble the relay where access is difficult, for example, when relays are mounted side-by-side.
They can be mounted as required.
Siemens IC 10 · 2014
5/53
5
Plug-in relay coupling links can be ordered as complete units or
as individual modules for customer assembly.
© Siemens AG 2013
Coupling Relays
Coupling Relays with LZS/LZX Plug-In Relays
Plug-in relay couplers
■ Technical specifications
Relay type
LZX:RT print relay, 8-pole,
(12.7 mm) 1 CO/2 CO
LZX:PT industrial relay, 8-, 11- and 14-pole,
(22.5 mm) 2 CO/3 CO/4 CO
mm
15.5 x 78 x 71
28 x 74 x 72
mm
15.5 x 77 x 71
28 x 77 x 79
mm
15.5 x 98 x 71
28 x 98 x 79
Rated control supply voltage Us1)
V
24 DC
Rated insulation voltage Ui
(pollution degree 3)
V
250
250
Overvoltage category
acc. to IEC 60664-1
III
III
Protective separation
between coil and contacts
acc. to IEC 60947-1, Appendix N
Up to 250 V (with plug-in base LZS:RT78726)
No (for complete units with standard socket)
No
IP67
IP20
IP50
IP20
-40 ... +70
-40 ... +80
-40 ... +70
-40 ... +80
Dimensions (W x H x D)
• LZX:RT.D4 / LZX:PT.D5
D
• LZX:RT.B4 / LZX:PT.B5
H
• LZX:RT.A4 / LZX:PT.A5
W
5
General technical specifications
Degree of protection
• Relays
• Bases
Permissible ambient temperature
• During operation
• During storage
°C
°C
24 AC
115 AC
230 AC
24 DC
24 AC
115 AC
230 AC
Conductor cross-sections
Connection type
Screw terminals
mm2
2
• Solid
• Finely stranded with end sleeve
• Corresponding opening tool
mm
Screw terminals
2 x 2.5
2 x 2.5
2 x 1.5
2 x 1.5
Screwdriver, size 3.0 ... 3.5 mm x 0.5 mm (3RA29 08-1A)
Connection type
Plug-in terminals (push-in)
Plug-in terminals (push-in)
mm2
mm2
mm2
1 x (0.75 ... 1.5), 2 x (0.75 ... 1.0), 2 x 1.5
1 x (0.75 ... 1.5), 2 x (0.75 ... 1.0), 2 x 1.5
1 x (0.75 ... 1.0), 2 x 0.75, 1 x 1.5
1 x (0.75 ... 1.5), 2 x (0.75 ... 1.0), 2 x 1.5
1 x (0.75 ... 1.5), 2 x (0.75 ... 1.0), 2 x 1.5
1 x (0.75 ... 1.0), 2 x 0.75, 1 x 1.5
Operating range at 20 °C
V
16.8 ... 52
18 ... 52
18 ... 40.8
19.2 ... 39.6 92 ... 190
Power consumption at Us
• AC
• DC
VA
W
-0.4
0.75
--
-0.75
1
--
Release voltage
V
2.4
7.2
3.6
7.2
Freewheel
diode for
complete
unit
--
Freewheel
diode in
LED
module
--
• Solid
• Finely stranded without end sleeve
• Finely stranded with end sleeve
Control side
Protection circuit
86.3 ... 127 172 ... 264
34.5
69
34.5
184 ... 380
69
Load side
Switching voltage
AC/DC
V
24 ... 250
24 ... 250
A
A
A
A
A
16
6
---
-12
10
6
• Rated operational current Ie AC-15 acc. to A
utilization categories (IEC 60947-5-1)
RT3 (1 changeover contact): 6
RT4 (2 changeover contacts): 2.5
PT2 (2 changeover contacts): 5
PT3 (3 changeover contacts): 5
PT5 (4 changeover contacts): 4 (DC coils),
2 (AC coils)
• Rated operational current Ie DC-13 with
suppressor diode acc. to utilization
categories (IEC 60947-5-1)
A
2 at 24 V
0.27 at 230 V
PT2, PT3: 5 at 24 V
PT5: 4 at 24 V
0.5 at 230 V
A
10
6
Standard 17 V, 10 mA;
hard gold-plated 17 V/0.1 mA
Standard 17 V, 10 mA;
hard gold-plated 20 mV/1 mA
Rated currents2)
• Conventional thermal current Ith
- 1 CO contact
- 2 CO contacts
- 3 CO contacts
- 4 CO contacts
Short-circuit protection
Short-circuit test with fuse links of
operational class gG
with short-circuit current Ik = 1 kA
acc. to IEC 60947-5-1
• DIAZED, type 5SB
Min. contact load
(reliability: 1 ppm)
Mechanical endurance
Operating cycles 30 x 106
Electrical endurance
(resistive load at 250 V AC)
Operating cycles 1 x 105
1)
10 x 106
AC voltages, 50 Hz; for 60 Hz operation, the lower response value must be
increased by 10 %; the power loss will reduce slightly.
5/54
Siemens IC 10 · 2014
10 x 106
1 x 105
2)
Capacitive loads can result in micro-welding on the contacts.
© Siemens AG 2013
Coupling Relays
Coupling Relays with LZS/LZX Plug-In Relays
Plug-in relay couplers
Relay type
mm
36 x 69 x 36
Rated control supply voltage Us1)
V
24 DC
Rated insulation voltage Ui
(pollution degree 3)
V
250
D
H
Dimensions (W x H x D)
MT industrial relay, 11-pole
(35.5 mm) 3 CO
W
AC and DC operation
Overvoltage category
acc. to IEC 60664-1
III
Protective separation
between coil and contacts
acc. to IEC 60947-1, Appendix N
No
Degree of protection of relay/base
• Relays
• Bases
24 AC
115 AC
230 AC
-45 ... +50
-45 ... +80
-45 ... +50
-45 ... +80
-45 ... +50
-45 ... +80
92 ... 137
184 ... 264
46
92
Permissible ambient temperature
• During operation
• During storage
°C
°C
-40 ... +60
-45 ... +80
Conductor cross-sections
Connection type
Screw terminals
mm2
2
• Solid
• Finely stranded with or without end sleeve
mm
• Corresponding opening tool
2 x 2.5
2 x 1.5
Screwdriver, size 1 or Pozidriv 1
Control side
Operating range at 20 °C
V
18 ... 38
19.2 ... 38
Power consumption
• AC
• DC
VA
W
-1.2
2.3
--
Release voltage
V
2.4
9.6
--
Protection circuit
Load side
Switching voltage
• AC/DC
V
24 ... 250
• Conventional thermal current Ith
A
10
• Rated operational current Ie /DC-13
acc. to utilization categories (IEC 60947-5-1)
A
2 at 24 V,
0.27 at 230 V
• Rated operational current Ie /AC-15
acc. to utilization categories (IEC 60947-5-1)
A
5 at 24 V and 230 V
A
10
Rated currents2)
Short-circuit protection
Short-circuit test with
fuse links of operational class gG
with short-circuit current Ik = 1 kA acc. to IEC 60947-5-1
• DIAZED, type 5SB
12 V DC/10 mA
Min. contact load
(reliability: 1 ppm)
Mechanical endurance
Operating cycles 20 x 106
Electrical endurance
(resistive load at 250 V AC)
Operating cycles 4 x 105
1)
AC voltages, 50 Hz; for 60 Hz operation, the lower response value must be
increased by 10 %; the power loss will reduce slightly.
2)
Capacitive loads can result in micro-welding on the contacts.
Siemens IC 10 · 2014
5/55
5
IP50
IP20
© Siemens AG 2013
Coupling Relays
Coupling Relays with LZS/LZX Plug-In Relays
Plug-in relay couplers
Circuit diagrams
(4)
42
44
(8)
11(9)
41(12)
(13)A1
11(7)
21(8)
(1)
12
14
(5)
(3)
32
34
(6)
31(9)
(13)A1
A2(14)
A2(14)
LZX:RT4
2-pole
11(9)
(3)
32
34
(7)
(2)
22
24
(6)
21(10)
31(11)
(13)A1
(4)
42
44
(8)
41(12)
A2(14)
LZX:MT32
3-pole
5
LZX:RT3
1-pole
(2)
22
24
(5)
(1)
12
14
(4)
NSB0_01011a
(1)
12
14
(5)
LZX:PT520, LZX:PT570, LZX:PT580
4-pole
NSB0_00250a
LZX:PT370
3-pole
NSB0_00249a
LZX:PT270
2-pole
A1
12
11
14
A2
22
21
24
A1
12
11
14
A2
22
21
24
(5)
22
(4)12
(8)32
(3)14
(9)34
NSB0_00248a
NSB0_00247a
NSB0_00251a
(2)
A1
Note:
Values in brackets: Plug-in base designations
Without brackets: Contact/coil designations
5/56
(6) (7)
21 24
Siemens IC 10 · 2014
(1) (11)
11 31
(10)
A2
© Siemens AG 2013
Coupling Relays
Coupling Relays with LZS/LZX Plug-In Relays
Plug-in relay couplers
■ Selection and ordering data
Version
Rated control supply Contacts, Width
voltage Us
number of
(at AC: 50/60 Hz)
CO
contacts
V
DT Article No.
Price
per PU
PU
(UNIT,
SET,
M)
PS*
PG
mm
Complete units, 11- and 14-pole, PT series
Complete units with plug-in base
for snap-on mounting onto TH 35 standard mounting rail
comprising:
• Coupling relays with plug-in relays
• Standard plug-in base with screw terminals
• LED module (version 24 V DC: LED module with freewheel diode)
• Fixing/ejection brackets
• Labels
3 CO contacts
24 DC
24 AC
115 AC
230 AC
3
28
A
A
A
A
LZS:PT3A5L24
LZS:PT3A5R24
LZS:PT3A5S15
LZS:PT3A5T30
1
1
1
1
5 units
5 units
5 units
5 units
41H
41H
41H
41H
4 CO contacts
24 DC
24 AC
115 AC
230 AC
4
28
A
A
A
A
LZS:PT5A5L24
LZS:PT5A5R24
LZS:PT5A5S15
LZS:PT5A5T30
1
1
1
1
5 units
5 units
5 units
5 units
41H
41H
41H
41H
A
A
A
A
LZS:PT5B5L24
LZS:PT5B5R24
LZS:PT5B5S15
LZS:PT5B5T30
1
1
1
1
5 units
5 units
5 units
5 units
41H
41H
41H
41H
LZS:PT3A5L24
Complete units with plug-in base
with logical separation
for snap-on mounting onto TH 35 standard mounting rail
comprising:
• Coupling relays with plug-in relays
• Plug-in base with logical separation and screw terminals
• LED module (version 24 V DC: LED module with freewheel diode)
• Fixing/ejection brackets
• Labels
4 CO contacts
24 DC
24 AC
115 AC
230 AC
4
28
Complete units, 8- and 14-pole, PT series
Complete units with plug-in base
with logical separation
for snap-on mounting onto TH 35 standard mounting rail
comprising:
• Coupling relays with plug-in relays
• Plug-in base with logical separation and plug-in terminals (push-in)
• LED module (version 24 V DC: LED module with freewheel diode)
• Fixing/ejection brackets
• Labels
Plug-in terminals
(push-in)
2 CO contacts
24 DC
230 AC
2
28
A
A
LZS:PT2D5L24
LZS:PT2D5T30
1
1
5 units
5 units
41H
41H
4 CO contacts
24 DC
24 AC
115 AC
230 AC
4
28
A
A
A
A
LZS:PT5D5L24
LZS:PT5D5R24
LZS:PT5D5S15
LZS:PT5D5T30
1
1
1
1
5 units
5 units
5 units
5 units
41H
41H
41H
41H
LZS:PT5D5L24
Note:
Logical separation: The terminals for the contacts and the terminals for the coil are arranged on separate levels, e.g. above for
contacts and below for the coil. Logical separation is not necessarily protective separation.
Protective separation: Protective separation prevents voltage of
one circuit affecting another circuit with sufficient protection
(IEC 61140).
* You can order this quantity or a multiple thereof.
Illustrations are approximate
Siemens IC 10 · 2014
5/57
5
Screw terminals
© Siemens AG 2013
Coupling Relays
Coupling Relays with LZS/LZX Plug-In Relays
Plug-in relay couplers
Version
Rated control supply Contacts, Width
voltage Us
number of
at AC 50/60 Hz
CO
contacts
V
DT Article No.
Price
per PU
PU
(UNIT,
SET,
M)
PS*
PG
mm
Individual modules for customer assembly, PT series
Industrial relays, 8-, 11-, and 14-pole
Mini industrial relays
• With test bracket and mechanical
switch position indicator, without LED1)
5
LZX:PT370024
24 DC
2
3
4
22.5
}
}
}
LZX:PT270024
LZX:PT370024
LZX:PT570024
1
1
1
1 unit
1 unit
1 unit
41H
41H
41H
24 AC
2
3
4
22.5
}
A
}
LZX:PT270524
LZX:PT370524
LZX:PT570524
1
1
1
1 unit
1 unit
1 unit
41H
41H
41H
115 AC
2
3
4
22.5
C
A
}
LZX:PT270615
LZX:PT370615
LZX:PT570615
1
1
1
1 unit
1 unit
1 unit
41H
41H
41H
230 AC
2
3
4
22.5
}
}
}
LZX:PT270730
LZX:PT370730
LZX:PT570730
1
1
1
1 unit
1 unit
1 unit
41H
41H
41H
24 DC
230 AC
4
22.5
}
}
LZX:PT580024
LZX:PT580730
1
1
1 unit
1 unit
41H
41H
24 DC
230 AC
4
22.5
}
C
LZX:PT520024
LZX:PT520730
1
1
1 unit
1 unit
41H
41H
• With hard gold-plating
• Without test bracket
Plug-in bases for PT relays
Standard plug-in bases
for mounting onto TH 35 standard mounting rail
--
Screw terminals
2
3
4
28
}
}
}
LZS:PT78720
LZS:PT78730
LZS:PT78740
1
1
1
1 unit
1 unit
1 unit
41H
41H
41H
2
4
28
}
}
LZS:PT78722
LZS:PT78742
1
1
1 unit
1 unit
41H
41H
1
1
1 unit
1 unit
41H
41H
LZS:PT78740
Plug-in bases with logical separation
for mounting onto TH 35 standard mounting rail
--
LZS:PT78722
Plug-in terminals
(push-in)
Plug-in bases with logical separation
for mounting onto TH 35 standard mounting rail
--
2
4
28
}
}
LZS:PT7872P
LZS:PT7874P
LZS:PT7874P
1)
The test bracket is designed to be non-latching. If the test bracket is
pressed further until 90° has been reached, two small lugs break off and
the test bracket can be latched in position.
Note:
Logical separation: The terminals for the contacts and the terminals for the coil are arranged on separate levels, e.g. above for
contacts and below for the coil. Logical separation is not necessarily protective separation.
Protective separation: Protective separation prevents voltage of
one circuit affecting another circuit with sufficient protection
(IEC 61140).
5/58
Siemens IC 10 · 2014
* You can order this quantity or a multiple thereof.
Illustrations are approximate
© Siemens AG 2013
Coupling Relays
Coupling Relays with LZS/LZX Plug-In Relays
Plug-in relay couplers
Version
Rated control supply Contacts, Width
voltage Us
number of
at AC 50/60 Hz
CO
contacts
V
DT Article No.
Price
per PU
PU
(UNIT,
SET,
M)
PS*
PG
mm
Individual modules for customer assembly, PT series
More individual modules
LED modules
• Red
With freewheel diode
24 DC
}
LZS:PTML0024
1
1 unit
41H
Without freewheel diode
24 AC/DC
}
LZS:PTML0524
1
1 unit
41H
110 … 230 AC/DC
}
LZS:PTML0730
1
1 unit
41H
LZS:PTML0024
--
12.5
• Green
24 DC
}
LZS:PTMG0024
1
1 unit
41H
24 AC
}
LZS:PTMG0524
1
1 unit
41H
110 … 230 AC/DC
}
LZS:PTMG0730
1
1 unit
41H
26
}
LZS:PT17021
100 10 units
41H
--
26
}
LZS:PT17024
100 10 units
41H
--
--
26
}
LZS:PT17040
100 10 units
41H
6 ... 60 AC
--
26
}
LZS:PTMU0524
1
1 unit
41H
}
LZS:PTMU0730
1
1 unit
41H
}
LZS:PTMT00A0
1
1 unit
41H
A
3TX7004-8BA00
1
1 unit
41H
}
LZS:PT170R6
1 10 units
41H
}
LZS:PT170P1
1 10 units
41H
--
12.5
Fixing/ejection brackets for PT base
with logical separation
Screw terminals and
plug-in terminals (push-in)
5
LZS:PT17021
With freewheel diode
Without freewheel diode
--
Fixing/ejection brackets for standard plug-in base
without logical separation
Screw terminals
Labels
LZS:PT17024
RC elements
LZS:PT17040
110 … 230 AC
Freewheel diodes with connection to A1
6 … 230 DC
--
26
Connecting cables, 24-pole
LZS:PTMU0730
Current carrying capacity 12 A,
with supply cable, blue
Connecting combs for PT screw base
6-pole,
10 A current carrying capacity, natural-colored
Connecting brackets for PT push-in base
3TX7004-8BA00
2-pole,
10 A current carrying capacity, natural-colored
Individual modules for customer assembly, MT series
Industrial relays, 11-pole
Industrial relays with test bracket
LZX:MT326024
Without LED
With LED
24 DC
3
35.5
A
}
LZX:MT321024
LZX:MT323024
1
1
1 unit
1 unit
41H
41H
Without LED
With LED
24 AC
3
35.5
A
C
LZX:MT326024
LZX:MT328024
1
1
1 unit
1 unit
41H
41H
Without LED
With LED
115 AC
3
35.5
C
C
LZX:MT326115
LZX:MT328115
1
1
1 unit
1 unit
41H
41H
Without LED
With LED
230 AC
3
35.5
A
A
LZX:MT326230
LZX:MT328230
1
1
1 unit
1 unit
41H
41H
Screw terminals
Plug-in bases
for mounting onto TH 35 standard mounting rail
--
38
}
LZS:MT78750
1
1 unit
41H
--
38
}
LZS:MT28800
1
1 unit
41H
Retaining brackets
--
LZS:MT78750
Note:
Note:
Logical separation: The terminals for the contacts and the terminals for the coil are arranged on separate levels, e.g. above for
contacts and below for the coil. Logical separation is not necessarily protective separation.
For coil voltages which are not listed, SITOP DC power supplies
can be used, e.g. 6EP1331-5BA00 or 6EP1331-5BA10;
see Chapter 15, "Stabilized Power Supplies" ➞ "SITOP Power
Supplies".
Protective separation: Protective separation prevents voltage of
one circuit affecting another circuit with sufficient protection
(IEC 61140).
* You can order this quantity or a multiple thereof.
Illustrations are approximate
Siemens IC 10 · 2014
5/59
© Siemens AG 2013
Coupling Relays
Coupling Relays with LZS/LZX Plug-In Relays
Plug-in relay couplers
Version
Rated control supply Contacts, Width
voltage Us
number of
at AC 50/60 Hz
CO
contacts
V
DT Article No.
Price
per PU
PU
(UNIT,
SET,
M)
PS*
PG
mm
Complete units, 8-pole, 5 mm pinning, RT series
Complete units with standard plug-in base
for snap-on mounting onto TH 35 standard mounting rail
comprising:
• Coupling relays with plug-in relays
• Standard plug-in base with screw terminals
• LED module (version 24 V DC: LED module with freewheel diode)
• Fixing/ejection brackets
• Labels
Screw terminals
1 CO contact
24 DC
24 AC
115 AC
230 AC
1
15.5
A
A
A
A
LZS:RT3A4L24
LZS:RT3A4R24
LZS:RT3A4S15
LZS:RT3A4T30
1
1
1
1
5 units
5 units
5 units
5 units
41H
41H
41H
41H
2 CO contacts
24 DC
24 AC
115 AC
230 AC
2
15.5
A
A
A
A
LZS:RT4A4L24
LZS:RT4A4R24
LZS:RT4A4S15
LZS:RT4A4T30
1
1
1
1
5 units
5 units
5 units
5 units
41H
41H
41H
41H
5
LZS:RT4A4T30
Complete units with plug-in base
with logical separation
for snap-on mounting onto TH 35 standard mounting rail
comprising:
• Coupling relays with plug-in relays
• Plug-in base with logical separation and screw terminals
• LED module (version 24 V DC: LED module with freewheel diode)
• Fixing/ejection brackets
• Labels
1 CO contact
24 DC
24 AC
115 AC
230 AC
1
15.5
A
A
A
A
LZS:RT3B4L24
LZS:RT3B4R24
LZS:RT3B4S15
LZS:RT3B4T30
1
1
1
1
5 units
5 units
5 units
5 units
41H
41H
41H
41H
2 CO contacts
24 DC
24 AC
115 AC
230 AC
2
15.5
A
A
A
A
LZS:RT4B4L24
LZS:RT4B4R24
LZS:RT4B4S15
LZS:RT4B4T30
1
1
1
1
5 units
5 units
5 units
5 units
41H
41H
41H
41H
LZS:RT4B4T30
Complete units with plug-in base
with logical separation
for snap-on mounting onto TH 35 standard mounting rail
comprising:
• Coupling relays with plug-in relays
• Plug-in base with logical separation and plug-in terminals (push-in)
• LED module (version 24 V DC: LED module with freewheel diode)
• Fixing/ejection brackets
• Labels
LZS:RT3D4L24
Plug-in terminals
(push-in)
1 CO contact
24 DC
24 AC
115 AC
230 AC
1
15.5
A
A
A
A
LZS:RT3D4L24
LZS:RT3D4R24
LZS:RT3D4S15
LZS:RT3D4T30
1
1
1
1
5 units
5 units
5 units
5 units
41H
41H
41H
41H
2 CO contacts
24 DC
24 AC
115 AC
230 AC
2
15.5
A
A
A
A
LZS:RT4D4L24
LZS:RT4D4R24
LZS:RT4D4S15
LZS:RT4D4T30
1
1
1
1
5 units
5 units
5 units
5 units
41H
41H
41H
41H
Note:
Logical separation: The terminals for the contacts and the terminals for the coil are arranged on separate levels, e.g. above for
contacts and below for the coil. Logical separation is not necessarily protective separation.
Protective separation: Protective separation prevents voltage of
one circuit affecting another circuit with sufficient protection
(IEC 61140).
5/60
Siemens IC 10 · 2014
* You can order this quantity or a multiple thereof.
Illustrations are approximate
© Siemens AG 2013
Coupling Relays
Coupling Relays with LZS/LZX Plug-In Relays
Plug-in relay couplers
Version
Rated control supply Contacts, Width
voltage Us
number of
at AC 50/60 Hz
CO
contacts
V
DT Article No.
Price
per PU
PU
(UNIT,
SET,
M)
PS*
PG
mm
Individual modules for customer assembly, RT series
Print relays, 8-pole, 5 mm pinning
Print relays
with hard gold-plating
Version with 1 CO contact
LZX:RT314024
24 DC
230 AC
1
12.7
}
C
LZX:RT315024
LZX:RT315730
1
1
1 unit
1 unit
41H
41H
24 DC
24 AC
115 AC
230 AC
1
12.7
}
C
C
}
LZX:RT314024
LZX:RT314524
LZX:RT314615
LZX:RT314730
1
1
1
1
1 unit
1 unit
1 unit
1 unit
41H
41H
41H
41H
12 DC
24 DC
2
12.7
C
}
LZX:RT424012
LZX:RT424024
1
1
1 unit
1 unit
41H
41H
}
}
}
LZX:RT424524
LZX:RT424615
LZX:RT424730
1
1
1
1 unit
1 unit
1 unit
41H
41H
41H
Print relays
5
Version with 1 CO contact
Version with 2 CO contacts
LZS:RT78725
24 AC
115 AC
230 AC
Screw terminals
Standard plug-in bases
for mounting onto TH 35 standard mounting rail
--
--
15.5
}
LZS:RT78725
1
1 unit
41H
--
15.5
}
LZS:RT78726
1
1 unit
41H
Plug-in bases with logical separation
for mounting onto TH 35 standard mounting rail
-LZS:RT78726
Plug-in terminals
(push-in)
Plug-in bases with logical separation
for mounting onto TH 35 standard mounting rail
--
--
15.5
}
LZS:RT7872P
1
1 unit
41H
15.5
}
LZS:PTML0024
1
1 unit
41H
}
}
LZS:PTML0524
LZS:PTML0730
1
1
1 unit
1 unit
41H
41H
}
LZS:PTMG0024
1
1 unit
41H
}
}
LZS:PTMG0524
LZS:PTMG0730
1
1
1 unit
1 unit
41H
41H
LED modules
• Red
LZS:RT7872P
With freewheel diode
24 DC
--
Without freewheel diode
24 AC/DC
110 ... 230 AC/DC
---
• Green
With freewheel diode
24 DC
--
Without freewheel diode
24 AC/DC
110 ... 230 AC/DC
---
15.5
--
--
15.5
}
LZS:RT17016
100 10 units
41H
--
--
15.5
}
LZS:RT17040
100 10 units
41H
6 ... 60 AC
110 ... 230 AC
--
15.5
}
}
LZS:PTMU0524
LZS:PTMU0730
1
1
1 unit
1 unit
41H
41H
--
15.5
}
LZS:PTMT00A0
1
1 unit
41H
A
3TX7004-8BA00
1
1 unit
41H
}
LZS:RT170R8
1 10 units
41H
}
LZS:RT170P1
100 10 units
41H
LZS:PTML0024
Fixing/ejection brackets
for RT base
Labels
LZS:RT17016
RC elements
Freewheel diodes with connection to A1
LZS:RT17040
6 ... 230 DC
Connecting cables, 24-pole
Current carrying capacity 12 A,
with supply cable, blue
Connecting combs for RT screw base
LZS:PTMT0730
8-pole,
10 A current carrying capacity, natural-colored
Connecting brackets for PT push-in base
2-pole,
10 A current carrying capacity, natural-colored
3TX7004-8BA00
Note:
For coil voltages which are not listed, SITOP DC power supplies
can be used, e.g. 6EP1331-5BA00 or 6EP1331-5BA10;
* You can order this quantity or a multiple thereof.
Illustrations are approximate
see Chapter 15, "Stabilized Power Supplies" ➞ "SITOP Power
Supplies".
Siemens IC 10 · 2014
5/61
© Siemens AG 2013
Coupling Relays
Coupling Relays with LZS/LZX Plug-In Relays
Plug-in relay couplers
■ More information
Notes on configuration
PT series
RT series
Mounting the LZS:PT17024 fixing/ejection bracket on the
standard plug-in base with LZS:PT787.0 screw terminal
Mounting the LZS:RT17016 fixing/ejection bracket on the
LZS:RT7872 plug-in base
5
3
1
2
1 Interlock
2 Direction of assembly
Mounting the coupling relay with plug-in relay
2
NSB0_01790a
NSB0_01788
1
1 Interlock
2 Direction of assembly
3 Direction of disassembly
Mounting the coupling relay with plug-in relay
NSB0_01890a
NSB0_01889
Note:
Note:
The LZS:PT17021 and LZS:PT17024 ejection brackets of the
coupling relays with plug-in relay are not status displays!
The LZS:RT17016 ejection brackets of the coupling relays with
plug-in relay are not status displays!
5/62
Siemens IC 10 · 2014
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement