This little USB stick contains a microcontroller with the code for ST s classic programmer/emulator for STM8 and STM32 bit processors

This little USB stick contains a microcontroller with the code for ST s classic programmer/emulator for STM8 and STM32 bit processors
ST-LINK/V2
ST-LINK/V2 in-circuit debugger/programmer for STM8 and STM32
Data brief
Features
 5 V power supplied by a USB connector
 USB 2.0 full-speed-compatible interface
 USB standard A to Mini- B cable
 SWIM specific features
– 1.65 V to 5.5 V application voltage
supported on SWIM interface
– SWIM low-speed and high-speed modes
supported
– SWIM programming speed rate:
9.7 Kbytes/s in low speed and
12.8 Kbytes/s in high speed
– SWIM cable for connection to the
application via an ERNI standard
vertical connector (ref: 284697 or 214017)
or horizontal connector (ref: 214012)
– SWIM cable for connection to the
application via a pin header or a 2.54 mm
pitch connector
 JTAG/serial wire debugging (SWD) specific
features:
– 1.65 V to 3.6 V application voltage
supported on the JTAG/SWD interface and
5 V tolerant inputs
– JTAG cable for connection to a standard
JTAG 20-pin pitch 2.54 mm connector
– JTAG supported
– SWD and serial wire viewer (SWV)
communication supported
1. The first figure at the top shows the
ST-LINK/V2-ISOL, while the second figure shows the
ST-LINK/V2.
 Direct firmware update feature supported
(DFU)
 Status LED which blinks during communication
with the PC
 Operating temperature 0 to 50 °C
 1000 Vrms high isolation voltage
(ST-LINK/V2-ISOL only)
March 2016
DocID018751 Rev 4
For further information contact your local STMicroelectronics sales office.
1/4
www.st.com
Description
ST-LINK/V2
Description
The ST-LINK/V2 is an in-circuit debugger and programmer for the STM8 and STM32
microcontroller families. The single wire interface module (SWIM) and JTAG/serial wire
debugging (SWD) interfaces are used to communicate with any STM8 or STM32
microcontroller located on an application board.
In addition to provide the same functionalities as the ST-LINK/V2, the ST-LINK/V2-ISOL
features digital isolation between the PC and the target application board. It also withstands
voltages of up to 1000 Vrms.
STM8 applications use the USB full-speed interface to communicate with the ST Visual
Develop (STVD) or ST Visual Program (STVP) software.
STM32 applications use the USB full-speed interface to communicate with Atollic®, IAR™,
Keil® or TASKING integrated development environments.
2/4
DocID018751 Rev 4
ST-LINK/V2
Revision history
Revision history
Table 1. Document revision history
Date
Revision
Changes
21-Apr-2011
1
Initial release.
07-May-2012
2
Added SWD to JTAG connection features.
14-Sep-2012
3
Added ST-LINK/V2-ISOL.
24-Mar-2016
4
Updated Vrms value in Features and Description.
DocID018751 Rev 4
3/4
4
ST-LINK/V2
IMPORTANT NOTICE – PLEASE READ CAREFULLY
STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and
improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on
ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order
acknowledgement.
Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or
the design of Purchasers’ products.
No license, express or implied, to any intellectual property right is granted by ST herein.
Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product.
ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners.
Information in this document supersedes and replaces information previously supplied in any prior versions of this document.
© 2016 STMicroelectronics – All rights reserved
4/4
DocID018751 Rev 4
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
STMicroelectronics:
ST-LINK/V2 ST-LINK/V2-ISOL
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement